AXA003A0X-SRZ

GE Data Sheet 12V Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 8.3Vdc – 14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current Features RoHS Compliant ▪ Compliant to RoHS Directive 2011/65/EU and amended Directive (EU) 2015/863 ▪ Compliant to REACH Directive (EC) No 1907/2006 ▪ Delivers up to 3A output current ▪ High efficiency – 91% at 3.3V full load (VIN = 12.0V) ▪ Small size and low profile: 20.3 mm x 11.4 mm x 7.27 mm (0.80 in x 0.45 in x 0.286 in) Applications ▪ Low output ripple and noise ▪ Constant switching frequency (300 kHz) ▪ Output voltage programmable from 0.75 Vdc to 5.5 Vdc via external resistor ▪ Line Regulation: 0.3% (typical) ▪ Distributed power architectures ▪ Load Regulation: 0.4% (typical) ▪ Intermediate bus voltage applications ▪ Temperature Regulation: 0.4 % (typical) ▪ Telecommunications equipment ▪ Remote On/Off ▪ Servers and storage applications ▪ Output overcurrent protection (non-latching) ▪ Networking equipment ▪ ▪ Enterprise Networks Wide operating temperature range (-40°C to 85°C) ▪ Latest generation IC’s (DSP, FPGA, ASIC) and Microprocessor powered applications ▪ ANSI/UL* 62368-1 and CAN/CSA† C22.2 No. 62368-1 Recognized, DIN VDE‡ 0868-1/A11:2017 (EN623681:2014/A11:2017 ▪ ISO** 9001 and ISO 14001 certified manufacturing facilities Description Austin MiniLynxTM 12V SMT (surface mount technology) power modules are non-isolated dc-dc converters that can deliver up to 3A of output current with full load efficiency of 91% at 3.3V output. These modules provide precisely regulated output voltage programmable via external resistor from 0.75Vdc to 5.5Vdc over a wide range of input voltage (VIN = 8.3 - 14V). Their open-frame construction and small footprint enable designers to develop cost- and space-efficient solutions. In addition to sequencing, standard features include remote On/Off, programmable output voltage and over current protection. * UL is a registered trademark of Underwriters Laboratories, Inc. † CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards ‡ July 24, 2020 ©2015 General Electric Company. All rights reserved. GE Data Sheet 12V Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Input Voltage Device Symbol Min Max Unit All VIN -0.3 15 Vdc All TA -40 85 °C All Tstg -55 125 °C Continuous Operating Ambient Temperature (see Thermal Considerations section) Storage Temperature Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Vo,set ≤ 3.63 VIN 8.3 Vo,set > 3.63 VIN 8.3 All IIN,max VO,set = 0.75Vdc IIN,No load 45 mA VO,set = 5.5Vdc IIN,No load 150 mA All IIN,stand-by 1.2 mA Inrush Transient All I2t Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1μH source impedance; VIN, min to VIN, max, IO= IOmax ; See Test configuration section) All 30 Input Ripple Rejection (120Hz) All 30 Operating Input Voltage Maximum Input Current Max Unit 12 14 Vdc 12 13.2 Vdc 2.2 Adc (VIN= VIN, min to VIN, max, IO=IO, max VO,set = 3.3Vdc) Input No Load Current (VIN = VIN, nom Vdc, IO = 0, module enabled) Input Stand-by Current (VIN = 5.5Vdc, module disabled) 0.4 A2s mAp-p dB CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to being part of a complex power architecture. To preserve maximum flexibility, internal fusing is not included, however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 6 A (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. July 24, 2020 ©2015 General Electric Company. All rights reserved. Page 2 GE Data Sheet 12V Austin MiniLynxTM: SMT Non-Isolated DC-DC Power Modules 8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current Electrical Specifications (continued) Parameter Output Voltage Set-point Device Symbol Min Typ Max Unit All VO, set -2.5 VO, set +2.5 % VO, set All VO, set -3% ⎯ +4% % VO, set All VO 0.7525 5.5 Vdc (VIN=IN, min, IO=IO, max, TA=25°C) Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end of life) Adjustment Range Selected by an external resistor Output Regulation Line (VIN=VIN, min to VIN, max) All ⎯ 0.3 ⎯ % VO, set Load (IO=IO, min to IO, max) All ⎯ 0.4 ⎯ % VO, set Temperature (Tref=TA, min to TA, max) All ⎯ 0.4 ⎯ % VO, set RMS (5Hz to 20MHz bandwidth) All ⎯ 10 15 mVrms Peak-to-Peak (5Hz to 20MHz bandwidth) All ⎯ 30 50 mVpk-pk Output Ripple and Noise on nominal output (VIN=VIN, nom and IO=IO, min to IO, max Cout = 1μF ceramic//10μFtantalum capacitors) External Capacitance ESR ≥ 1 mΩ All CO, max ⎯ ⎯ 1000 μF ESR ≥ 10 mΩ All CO, max ⎯ ⎯ 3000 μF Output Current All Io 0 3 Adc Output Current Limit Inception (Hiccup Mode ) All IO, lim ⎯ 200 ⎯ % Io All IO, s/c ⎯ 2 ⎯ Adc VO,set = 1.2Vdc η 81.5 % VIN= VIN, nom, TA=25°C VO, set = 1.5Vdc η 84.0 % IO=IO, max , VO= VO,set VO,set = 1.8Vdc η 86.0 % VO,set = 2.5Vdc η 89.0 % VO,set = 3.3Vdc η 91.0 % VO,set = 5.0Vdc η 93.0 All fsw All Settling Time (Vo