KW006A0A41-SRZ

Data Sheet October 5, 2009 KW006-010 Series (Sixteenth-Brick) DC-DC Converter Power Modules: 36–75Vdc Input; 3.3Vdc to 5.0Vdc Output; 6A to 10A Output Current RoHS Compliant Features Applications ƒ Distributed power architectures ƒ Wireless networks ƒ Access and optical network Equipment ƒ Enterprise Networks ƒ Latest generation IC’s (DSP, FPGA, ASIC) and Microprocessor powered applications ƒ Compliant to RoHS EU Directive 2002/95/EC (-Z versions) ƒ Compliant to RoHS EU Directive 2002/95/EC with lead solder exemption (non-Z versions) ƒ Delivers up to 33W output power: 3.3V(10A), 5.0V(6A) ƒ Small size and low profile: 33.0 mm x 22.9 mm x 8.75 mm (1.30 in x 0.9 in x 0.344 in) ƒ Industry standard DOSA footprint ƒ Output voltage adjustment trim (-20%, +10%) ƒ Remote On/Off, Positive logic ƒ Remote Sense ƒ Over-temperature protection (non-latching) ƒ Output over-current protection (non-latching) ƒ Output over-voltage protection (latching) ƒ Wide operating temperature range (-40°C to 85°C) ƒ Meets the voltage isolation requirements for ETSI 300-132-2 and complies with and is licensed for Basic Insulation rating per EN60950-1 ƒ CE mark meets the 2006/95/EC directive ƒ UL* 60950-1Recognized, CSA† C22.2 No. 60950-1-03 Certified, and VDE‡ 0805 (EN60950 3rd Edition) Licensed ƒ ISO** 9001 and ISO 14001 certified manufacturing facilities ƒ Surface Mount (Tape and Reel, -SR Suffix) Options ƒ Negative Remote On/Off logic § Description The KW (Sixteenth-brick) series power modules are isolated dc-dc converters that operate over a wide input voltage range of 36 to 75Vdc and provide a single precisely regulated output. The output is fully isolated from the input, allowing versatile polarity configurations and grounding connections. The modules exhibit high efficiency, typical efficiency of 87% for 3.3V/10A. These open frame modules are available in surface-mount (-SR) form. * UL is a registered trademark of Underwriters Laboratories, Inc. † CSA is a registered trademark of Canadian Standards Association. ‡ VDE is a trademark of Verband Deutscher Elektrotechniker e.V. § This product is intended for integration into end-user equipment. All of the required procedures of end-user equipment should be followed. ** ISO is a registered trademark of the International Organization of Standards Document No: DS06-114 ver.1.32 PDF name: kw006-010.ds.pdf Data Sheet October 5, 2009 KW0006-010 Series Power Modules: 36 – 75Vdc Input; 3.3 to 5.0Vdc Output; 6 to 10A Output Current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit Continuous All VIN -0.3 80 Vdc Transient (100 ms) All VIN,trans -0.3 100 Vdc All TA -40 85 °C Storage Temperature All Tstg -55 125 °C I/O Isolation voltage (100% Factory tested) All ⎯ ⎯ 1500 Vdc Input Voltage Operating Ambient Temperature (see Thermal Considerations section) Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit Operating Input Voltage All VIN 36 48 75 Vdc Maximum Input Current All IIN,max 1.5 Adc All IIN,No load 40 75 mA All IIN,stand-by 3 5 mA Inrush Transient All It 0.1 As Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1μH source impedance; VIN, min to VIN, max, IO= IOmax ; See Test configuration section) All Input Ripple Rejection (120Hz) All (VIN= VIN, min to VIN, max, IO=IO, max) Input No Load Current (VIN = VIN, nom, IO = 0, module enabled) Input Stand-by Current (VIN = VIN, nom, module disabled) EMC, EN55022 2 30 50 2 mAp-p dB See EMC Considerations section CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to an integrated part of sophisticated power architectures. To preserve maximum flexibility, internal fusing is not included, however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a time-delay fuse with a maximum rating of 5 A (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. LINEAGE POWER 2 Data Sheet October 5, 2009 KW0006-010 Series Power Modules: 36 – 75Vdc Input; 3.3 to 5.0Vdc Output; 6 to 10A Output Current Electrical Specifications (continued) Parameter Output Voltage Set-point Device Symbol Min Typ Max Unit All VO, set -1.5 ⎯ +1.5 % VO, set All VO -3.0 ⎯ +3.0 % VO, set All VO,adj -20.0 +10.0 Vdc % VO, set (VIN=VIN, min, IO=IO, max, TA=25°C) Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end of life) Adjustment Range Selected by an external resistor Output Regulation Line (VIN=VIN, min to VIN, max) All ⎯ ⎯ 0.1 Load (IO=IO, min to IO, max) All ⎯ ⎯ 5 mV Temperature (Tref=TA, min to TA, max) All ⎯ ⎯ ±1.0 % VO, set F ⎯ ⎯ 20 mVrms Peak-to-Peak (5Hz to 20MHz bandwidth) F ⎯ ⎯ 60 mVpk-pk RMS (5Hz to 20MHz bandwidth) A ⎯ ⎯ 25 mVrms Peak-to-Peak (5Hz to 20MHz bandwidth) A ⎯ ⎯ 75 mVpk-pk μF Output Ripple and Noise on nominal output (VIN=VIN, nom ,IO= IO, max , TA=TA, min to TA, max) (see Figure 14 for test conditions) RMS (5Hz to 20MHz bandwidth) F CO, max 0* ⎯ 5,000 A CO, max 0* ⎯ 2,000 μF A Io 0 ⎯ 6 Adc F Io 0 ⎯ 10 Adc All IO, lim 101 130 % Io All IO, s/c ⎯ ⎯ Arms All η 87.0 % All fsw 300 kHz Peak Deviation All Vpk Settling Time (Vo