ACT38A

Tel: 0044 (0)118 979 1238 Fax: 0044 (0)118 979 1283 E-mail: info@actcrystals.com ACT39 / 38A The ACT39 is a compact crystal resonator offering high vibration and shock resistance together with high stability. It is most suitable for portable equipment and close packing density. The device is offered with frequencies between 4.0 and 70.0MHz. Specification Parameter Frequency Symbol fo Specification 4.0-14MHz 14-49.5MHZ 49.5-70MHz ±30~50ppm ±10~50ppm (typ±30) ±30~50ppm ±30~50ppm ±10~50ppm (typ±30) ±30~50ppm -20 ~ +70°C -10~+70°C -20 ~ +70°C -40 ~ +85°C 150Ω max 100Ω max 60Ω max 40Ω max 30Ω max 100Ω max 80Ω max 5.0pF typical 16.0pF (Others available.) 50~100 μ W 500MΩ Min ±5ppm max Condition case size 3x9mm case size 3x8mm case size 3x9mm 4.0-10MHz 10-49.5MHZ 49.5-70MHz 4.0-10MHz 10-49.5MHZ 49.5-70MHz 4.0-10MHz 10~49.5MHz 49.5~70MHz ( 39 ) ( 38A ) ( 39 ) Frequency Tolerance @25°C Δf/fo Frequency Stability Δf/fo Temp Operating Range Topr Temp Storage Range Equivalent Series Resistance Tstg ESR 4.0~6.0MHz 6.0~10.0MHz 10.0~14.0MHz 16.0~20.0MHz 20.0~30.0MHz 30.0~49.5MHz( 3rd O/T) 49.5~70MHz( 3rd O/T) Please specify DC100V±15V @ 25°C ±3°C 1st year Shunt Capacitance Load Capacitance Drive Level Insulation Resistance Aging C0 CL DL IR Fa Please note that all parameters can not necessarily be specified in the same device Customer to Specify : Frequency, Frequency Tolerance, Operating Temperature Range & Load Capacitance In line with our ongoing policy of product evolvement and improvement, the above specification may be subject to change without notice. ISO9001: 2000 Registered For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK Issue : 3 C1 (M4) Date : 07/09/04 http://www.actcrystals.com 1 of 2 Tel: 0044 (0)118 979 1238 Fax: 0044 (0)118 979 1283 E-mail: info@actcrystals.com SOLDERING of CYLINDER CRYSTALS Lead wire should be soldered within 5 seconds with the iron having a tip temperature of less than 270°C. Case temperature should not exceed 150°C With regard to wave soldering it is recommended that the process is carried out with the crystal unit set upright on the circuit board. Should the process be carried out with the crystal unit on its side then steps must be taken to prevent heat transfer through the can. Should the whole crystal unit be heated (in a re-flow oven for example) it will result in amarked deterioration of the performance or even failure to oscillate. This is due to the internal construction of the crystal unit which involves the use of solder. Please note that all parameters can not necessarily be specified in the same device Customer to Specify : Frequency, Frequency Tolerance, Operating Temperature Range & Load Capacitance In line with our ongoing policy of product evolvement and improvement, the above specification may be subject to change without notice. ISO9001: 2000 Registered For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK http://www.actcrystals.com Issue : 3 C1 (M4) Date : 07/09/04 2 of 2