24AA32AT-I/ST

24AA32A/24LC32A 32-Kbit I2C Serial EEPROM Device Selection Table VCC Range Maximum Clock Frequency Temperature Ranges 1.7V-5.5V 400 kHz(1) I 24LC32A 2.5V-5.5V 400 kHz I, E Note 1: 100 kHz for VCC 4,000V • More than 1 Million Erase/Write Cycles • Data Retention > 200 Years • Factory Programming Available • RoHS Compliant • Temperature Ranges: - Industrial (I): -40°C to +85°C - Extended (E): -40°C to +125°C • Automotive AEC-Q100 Qualified The Microchip Technology Inc. 24XX32A(1) is a 32-Kbit Electrically Erasable PROM (EEPROM). The device is organized as a single block of 4K x 8-bit memory with a two-wire serial interface. Its low-voltage design permits operation down to 1.7V, with standby and active currents of only 1 µA and 1 mA, respectively. The 24XX32A also has a page write capability for up to 32 bytes of data. Functional address lines allow up to eight devices on the same bus, for up to 256 Kbits address space. Packages Note 1: 24XX32A is used in this document as a generic part number for the 24AA32A/ 24LC32A devices. Block Diagram A0 A1 A2 WP I/O Control Logic Memory Control Logic HV Generator EEPROM Array XDEC Page Latches I/O SCL YDEC SDA • 8-Lead DFN, 8-Lead MSOP, 8-Lead PDIP, 8Lead SOIC, 8-Lead SOIJ, 5-Lead SOT-23, 8Lead TDFN, 8-Lead TSSOP and 8-Lead XRotated TSSOP Vcc VSS Sense Amp. R/W Control Package Types DFN/TDFN A0 1 A1 2 A2 3 VSS 4 8 VCC 7 WP 6 SCL 5 SDA SOT-23 PDIP/MSOP/SOIC/SOIJ/TSSOP A0 1 8 VCC SCL 1 A1 2 7 WP VSS 2 A2 3 6 SCL VSS 4 5 SDA SDA 3  2002-2021 Microchip Technology Inc. and its subsidiaries X-Rotated TSSOP 5 WP 4 VCC WP VCC A0 A1 1 2 3 4 8 7 6 5 SCL SDA VSS A2 DS20001713N-page 1 24AA32A/24LC32A 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings (†) VCC .............................................................................................................................................................................6.5V All inputs and outputs w.r.t. VSS ......................................................................................................... -0.3V to VCC +1.0V Storage temperature ...............................................................................................................................-65°C to +150°C Ambient temperature with power applied ................................................................................................-40°C to +125°C ESD protection on all pins  4 kV † NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. TABLE 1-1: DC CHARACTERISTICS DC CHARACTERISTICS Industrial (I): Extended (E): Param. Symbol No. Characteristic Minimum High-Level Input Voltage 0.7 VCC — — D1 D2 VIH TA = -40°C to +85°C, VCC = +1.7V to +5.5V TA = -40°C to +125°C, VCC = +2.5V to +5.5V Type Maximum Units Conditions — — V — 0.3 VCC V VCC 2.5V — 0.2 VCC V VCC < 2.5V 0.05 VCC — — V VCC  2.5V (Note 1) — — 0.40 V IOL = 3.0 mA, VCC = 4.5V IOL = 2.1 mA, Vcc = 2.5V VIL Low-Level Input Voltage D3 VHYS Hysteresis of Schmitt Trigger Inputs (SDA, SCL pins) D4 VOL Low-Level Output Voltage D5 ILI Input Leakage Current — — ±1 µA VIN = VSS or VCC D6 ILO Output Leakage Current — — ±1 µA VOUT = VSS or VCC D7 CIN, COUT Pin Capacitance (all inputs/outputs) — — 10 pF VCC = 5.0V (Note 1) TA = +25°C, FCLK = 1 MHz D8 ICC write — 0.1 3 mA VCC = 5.5V, SCL = 400 kHz D9 ICC read — 0.05 400 µA VCC = 5.5V, SCL = 400 kHz — 0.01 1 µA SDA = SCL = VCC A0, A1, A2, WP = VSS, ITemp. — — 5 µA SDA = SCL = VCC = 5.5V A0, A1, A2, WP = VSS, ETemp Operating Current D10 Note 1: 2: ICCS Standby Current This parameter is periodically sampled and not 100% tested. Typical measurements taken at room temperature. DS20001713N-page 2  2002-2021 Microchip Technology Inc. and its subsidiaries 24AA32A/24LC32A TABLE 1-2: AC CHARACTERISTICS Industrial (I): TA = -40°C to +85°C, VCC = +1.7V to +5.5V Extended (E):TA = -40°C to +125°C, VCC = +2.5V to +5.5V AC CHARACTERISTICS Param. Symbol No. 1 FCLK 2 THIGH 3 TLOW Characteristic Clock Frequency Clock High Time Clock Low Time 4 TR SDA and SCL Rise Time 5 TF SDA and SCL Fall Time 6 THD:STA Start Condition Hold Time 7 TSU:STA Start Condition Setup Time 8 THD:DAT Data Input Hold Time 9 TSU:DAT Data Input Setup Time 10 TSU:STO Stop Condition Setup Time 11 TSU:WP WP Setup Time 12 THD:WP WP Hold Time 13 TAA Output Valid from Clock 14 TBUF Bus free time: Time the bus must be free before a new transmission can start 15 TOF Output Fall Time from VIH Minimum to VIL Maximum 16 TSP 17 TWC 18 3: 4: Units Conditions — 400 kHz 2.5V  VCC  5.5V 1.7V  VCC  2.5V (24AA32A) — 100 kHz 600 — ns 2.5V  VCC  5.5V 4000 — ns 1.7V  VCC  2.5V (24AA32A) 1300 — ns 2.5V  VCC  5.5V 4700 — ns 1.7V  VCC  2.5V (24AA32A) — 300 ns 2.5V  VCC  5.5V (Note 1) — 1000 ns 1.7V  VCC  2.5V (24AA32A) (Note 1) — 300 ns Note 1 600 — ns 2.5V  VCC  5.5V 4000 — ns 1.7V  VCC  2.5V (24AA32A) 600 — ns 2.5V  VCC  5.5V 4700 — ns 1.7V  VCC  2.5V (24AA32A) Note 2 0 — ns 100 — ns 2.5V  VCC  5.5V 250 — ns 1.7V  VCC  2.5V (24AA32A) 600 — ns 2.5V  VCC  5.5V 4000 — ns 1.7V  VCC  2.5V (24AA32A) 600 — ns 2.5V VCC  5.5V 4000 — ns 1.7V VCC < 2.5V (24AA32A) 1300 — ns 2.5V VCC  5.5V 4700 — ns 1.7V VCC < 2.5V (24AA32A) — 900 ns 2.5V  VCC  5.5V (Note 2) — 3500 ns 1.7V  VCC  2.5V (24AA32A) (Note 2) 1300 — ns 2.5V  VCC  5.5V 4700 — ns 1.7V  VCC  2.5V (24AA32A) 20+0.1CB 250 ns 2.5V  VCC  5.5V — 250 ns 1.7V  VCC  2.5V (24AA32A) Input Filter Spike Suppression (SDA and SCL pins) — 50 ns Note 1 and Note 3 Write Cycle Time (byte or page) — 5 ms 1,000,000 — cycles Endurance Note 1: 2: Minimum Maximum +25°C, 5.5V, Page Mode (Note 4) Not 100% tested. CB = total capacitance of one bus line in pF. As a transmitter the device must provide an internal minimum delay time to bridge the undefined region (minimum 300 ns) of the falling edge of SCL to avoid unintended generation of Start or Stop conditions. The combined TSP and VHYS specifications are due to new Schmitt Trigger inputs which provide improved noise spike suppression. This eliminates the need for a TI specification for standard operation. This parameter is not tested but ensured by characterization.  2002-2021 Microchip Technology Inc. and its subsidiaries DS20001713N-page 3 24AA32A/24LC32A FIGURE 1-1: BUS TIMING DATA 5 SCL SDA IN 7 3 4 D4 2 8 10 9 6 16 14 13 SDA OUT (protected) (unprotected) WP FIGURE 1-2: 12 11 BUS TIMING START/STOP D4 SCL 6 7 10 SDA Start DS20001713N-page 4 Stop  2002-2021 Microchip Technology Inc. and its subsidiaries 24AA32A/24LC32A 2.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 2-1. TABLE 2-1: PIN FUNCTION TABLE Name PDIP SOIC SOIJ TSSOP Rotated DFN(1) TDFN(1) MSOP SOT-23 CS TSSOP Description A0 1 1 1 1 3 1 1 1 — — Chip Address Input A1 2 2 2 2 4 2 2 2 — — Chip Address Input A2 3 3 3 3 5 3 3 3 — — Chip Address Input VSS 4 4 4 4 6 4 4 4 2 2 Ground SDA 5 5 5 5 7 5 5 5 3 5 Serial Address/Data I/O SCL 6 6 6 6 8 6 6 6 1 4 Serial Clock WP 7 7 7 7 1 7 7 7 5 3 Write-Protect Input VCC 8 8 8 8 2 8 8 8 4 1 Power Supply Note 1: 2.1 The exposed pad on the DFN/TDFN packages can be connected to VSS or left floating. A0, A1, A2 Chip Address Inputs The A0, A1 and A2 inputs are used by the 24XX32A for multiple device operation. The levels on these inputs are compared with the corresponding bits in the client address. The chip is selected if the comparison is true. Up to eight devices may be connected to the same bus by using different Chip Select bit combinations. These inputs must be connected to either VCC or VSS. In most applications, the chip address inputs A0, A1 and A2 are hard-wired to logic ‘0’ or logic ‘1’. For applications in which these pins are controlled by a microcontroller or other programmable device, the chip address pins must be driven to logic ‘0’ or logic ‘1’ before normal device operation can proceed. Address pins are not available in the SOT-23 package. 2.2 2.3 Serial Clock (SCL) The SCL input is used to synchronize the data transfer to and from the device. 2.4 Write-Protect (WP) This pin must be connected to either VSS or VCC. If tied to VSS, write operations are enabled. If tied to VCC, write operations are inhibited but read operations are not affected. Serial Address/Data Input/Output (SDA) SDA is a bidirectional pin used to transfer addresses and data into and out of the device. It is an open-drain terminal; therefore, the SDA bus requires a pull-up resistor to VCC (typical 10 k for 100 kHz, 2 k for 400 kHz) For normal data transfer, SDA is allowed to change only during SCL low. Changes during SCL high are reserved for indicating Start and Stop conditions.  2002-2021 Microchip Technology Inc. and its subsidiaries DS20001713N-page 5 24AA32A/24LC32A 3.0 FUNCTIONAL DESCRIPTION The 24XX32A supports a bidirectional, two-wire bus and data transmission protocol. A device that sends data onto the bus is defined as transmitter, while a device receiving data is defined as a receiver. The bus has to be controlled by a host device which generates the Serial Clock (SCL), controls the bus access and generates the Start and Stop conditions, while the 24XX32A works as client. Both host and client can operate as transmitter or receiver, but the host device determines which mode is activated. 4.0 BUS CHARACTERISTICS The following bus protocol has been defined: • Data transfer may be initiated only when the bus is not busy. • During data transfer, the data line must remain stable whenever the clock line is high. Changes in the data line while the clock line is high will be interpreted as a Start or Stop condition. Accordingly, the following bus conditions have been defined (Figure 4-1). 4.1 Start Data Transfer (B) A high-to-low transition of the SDA line while the clock (SCL) is high determines a Start condition. All commands must be preceded by a Start condition. 4.3 Stop Data Transfer (C) A low-to-high transition of the SDA line while the clock (SCL) is high determines a Stop condition. All operations must be ended with a Stop condition. FIGURE 4-1: Data Valid (D) The state of the data line represents valid data when, after a Start condition, the data line is stable for the duration of the high period of the clock signal. The data on the line must be changed during the low period of the clock signal. There is one clock pulse per bit of data. Each data transfer is initiated with a Start condition and terminated with a Stop condition. The number of data bytes transferred between Start and Stop conditions is determined by the host device and is, theoretically, unlimited (although only the last 32 bytes will be stored when doing a write operation). When an overwrite does occur, it will replace data in a First-In First-Out (FIFO) principle. 4.5 Acknowledge Each receiving device, when addressed, is obliged to generate an Acknowledge after the reception of each byte. The host device must generate an extra clock pulse which is associated with this Acknowledge bit. Note: Bus Not Busy (A) Both data and clock lines remain high. 4.2 4.4 The 24XX32A does not generate any Acknowledge bits if an internal programming cycle is in progress. The device that acknowledges, has to pull down the SDA line during the Acknowledge clock pulse in such a way that the SDA line is stable-low during the high period of the Acknowledge-related clock pulse. Moreover, setup and hold times must be taken into account. During reads, a host must signal an end of data to the client by not generating an Acknowledge bit on the last byte that has been clocked out of the client. In this case, the client (24XX32A) will leave the data line high to enable the host to generate the Stop condition. DATA TRANSFER SEQUENCE ON THE SERIAL BUS (A) (B) (D) Start Condition Address or Acknowledge Valid (D) (C) (A) SCL SDA DS20001713N-page 6 Data Allowed to Change Stop Condition  2002-2021 Microchip Technology Inc. and its subsidiaries 24AA32A/24LC32A 5.0 DEVICE ADDRESSING FIGURE 5-1: A control byte is the first byte received following the Start condition from the host device. The control byte consists of a 4-bit control code. For the 24XX32A, this is set as ‘1010’ binary for read and write operations. The next 3 bits of the control byte are the Chip Select bits (A2, A1, A0). The Chip Select bits allow the use of up to eight 24XX32A devices on the same bus and are used to select which device is accessed. The Chip Select bits in the control byte must correspond to the logic levels on the corresponding A2, A1 and A0 pins for the device to respond. These bits are in effect the three Most Significant bits of the word address. The combination of the 4-bit control code and the next three bits are called the client address. For the SOT-23 package, the address pins are not available. During device addressing, the A1, A2, and A0 Chip Selects bits should be set to ‘0’. The last bit of the control byte is the Read/Write (R/W) bit and it defines the operation to be performed. When set to a ‘1’, a read operation is selected. When set to a zero, a write operation is selected. The next two bytes received define the address of the first data byte (Figure 5-2). Because only A11 to A0 are used, the upper four address bits are “don’t care” bits. The upper address bits are transferred first, followed by the Less Significant bits. CONTROL BYTE FORMAT Read/Write Bit Chip Select Bits Control Code S 1 0 1 A2 0 A1 A0 R/W ACK Client Address Start Bit 5.1 Acknowledge Bit Contiguous Addressing Across Multiple Devices The Chip Select bits A2, A1 and A0 can be used to expand the contiguous address space for up to 256 Kbits by adding up to eight 24XX32A devices on the same bus. In this case, software can use A0 of the control byte as address bit A12; A1 as address bit A13; and A2 as address bit A14. It is not possible to sequentially read across device boundaries. The SOT-23 package do not support multiple device addressing on the same bus. Following the Start condition, the 24XX32A monitors the SDA bus checking the device type identifier being transmitted and, upon receiving a valid client address and the R/W bit, the client device outputs an Acknowledge signal on the SDA line. Depending on the state of the R/W bit, the 24XX32A will select a read or write operation. FIGURE 5-2: ADDRESS SEQUENCE BIT ASSIGNMENTS Control Byte 1 0 1 Control Code 0 A 2 A 1 Address High Byte A 0 R/W x Chip Select Bits  2002-2021 Microchip Technology Inc. and its subsidiaries x x x A A 11 10 A 9 Address Low Byte A 8 A 7 • • • • • • A 0 x = “don’t care” bit DS20001713N-page 7 24AA32A/24LC32A 6.0 WRITE OPERATIONS 6.1 Byte Write Following the Start condition from the host, the control code (4 bits), the Chip Select (3 bits), and the R/W bit (which is a logic low) are clocked onto the bus by the host transmitter. This indicates to the addressed client receiver that the address high byte will follow once it has generated an Acknowledge bit during the ninth clock cycle. Therefore, the next byte transmitted by the host is the high-order byte of the word address and will be written into the Address Pointer of the 24XX32A. The next byte is the Least Significant Address Byte. After receiving another Acknowledge signal from the 24XX32A, the host device will transmit the data word to be written into the addressed memory location. The 24XX32A acknowledges again and the host generates a Stop condition. This initiates the internal write cycle and, during this time, the 24XX32A will not generate Acknowledge signals (Figure 6-1). If an attempt is made to write to the array with the WP pin held high, the device will acknowledge the command, but no write cycle will occur. No data will be written and the device will immediately accept a new command. After a byte Write command, the internal Address Pointer will point to the address location following the one that was just written. Note: 6.2 Page Write The write control byte, word address and the first data byte are transmitted to the 24XX32A in the same way as in a byte write. However, instead of generating a Stop condition, the host transmits up to 31 additional bytes which are temporarily stored in the on-chip page buffer and will be written into memory once the host has transmitted a Stop condition. Upon receipt of each word, the five lower Address Pointer bits, which form the byte counter, are internally incremented by ‘1’. The higher-order 7-bits of the word address remain constant. If the host should transmit more than 32bytes prior to generating the Stop condition, the Address Pointer will roll over and the previously received data will be overwritten. As with the byte write operation, once the Stop condition is received, an internal write cycle will begin (Figure 6-2). If an attempt is made to write to the array with the WP pin held high, the device will acknowledge the command, but no write cycle will occur, no data will be written, and the device will immediately accept a new command. Note: When doing a write of less than 32-bytes the data in the rest of the page is refreshed along with the data bytes being written. This will force the entire page to endure a write cycle, for this reason endurance is specified per page. 6.3 Page write operations are limited to writing bytes within a single physical page, regardless of the number of bytes actually being written. Physical page boundaries start at addresses that are integer multiples of the page buffer size (or ‘page size’) and end at addresses that are integer multiples of page size – 1. If a page write command attempts to write across a physical page boundary, the result is that the data wrap around to the beginning of the current page (overwriting data previously stored there), instead of being written to the next page as might be expected. It is therefore necessary for the application software to prevent page write operations that would attempt to cross a page boundary. Write Protection The WP pin allows the user to write-protect the entire array (000-FFF) when the pin is tied to VCC. If tied to VSS the write protection is disabled. The WP pin is sampled at the Stop bit for every Write command (Figure 4-1). Toggling the WP pin after the Stop bit will have no effect on the execution of the write cycle. DS20001713N-page 8  2002-2021 Microchip Technology Inc. and its subsidiaries 24AA32A/24LC32A FIGURE 6-1: BYTE WRITE Bus Activity Host S T A R T Control Byte Address High Byte AA S1 0 1 0A 210 0 SDA Line S T O P Data xxx x A C K Bus Activity Address Low Byte P A C K A C K A C K x = “don’t care” bit FIGURE 6-2: PAGE WRITE Bus Activity Host S T A R T SDA Line AA S10 1 0A 2100 Bus Activity Control Byte Address High Byte Address Low Byte Data Byte 0 S T O P P Data Byte 31 xxxx A C K A C K A C K A C K A C K x = “don’t care” bit  2002-2021 Microchip Technology Inc. and its subsidiaries DS20001713N-page 9 24AA32A/24LC32A 7.0 ACKNOWLEDGE POLLING Since the device will not acknowledge during a write cycle, this can be used to determine when the cycle is complete (this feature can be used to maximize bus throughput). Once the Stop condition for a write command has been issued from the host, the device initiates the internally-timed write cycle. ACK polling can then be initiated immediately. This involves the host sending a Start condition followed by the control byte for a write command (R/W = 0). If the device is still busy with the write cycle, then no ACK will be returned. If no ACK is returned, the Start bit and control byte must be re-sent. If the cycle is complete, the device will return the ACK and the host can then proceed with the next read or write operation. See Figure 7-1 for flow diagram of this operation. FIGURE 7-1: ACKNOWLEDGE POLLING FLOW Send Write Command Send Stop Condition to Initiate Write Cycle Send Start Send Control Byte with R/W = 0 Did Device Acknowledge (ACK = 0)? No Yes Next Operation DS20001713N-page 10  2002-2021 Microchip Technology Inc. and its subsidiaries 24AA32A/24LC32A 8.0 READ OPERATION 8.3 Read operations are initiated in the same way as write operations, with the exception that the R/W bit of the control byte is set to ‘1’. There are three basic types of read operations: current address read, random read and sequential read. 8.1 Current Address Read The 24XX32A contains an Address Pointer that maintains the address of the last word accessed, internally incremented by ‘1’. Therefore, if the previous read access was to address ‘n’ (n is any legal address), the next current address read operation would access data from address n + 1. Upon receipt of the control byte with R/W bit set to ‘1’, the 24XX32A issues an Acknowledge and transmits the 8-bit data word. The host will not acknowledge the transfer, but does generate a Stop condition and the 24XX32A discontinues transmission (Figure 8-1). 8.2 Sequential Read Sequential reads are initiated in the same way as a random read, except that once the 24XX32A transmits the first data byte, the host issues an Acknowledge as opposed to the Stop condition used in a random read. This Acknowledge directs the 24XX32A to transmit the next sequentially addressed 8-bit word (Figure 8-3). Following the final byte transmitted to the host, the host will NOT generate an Acknowledge, but will generate a Stop condition. To provide sequential reads, the 24XX32A contains an internal Address Pointer which is incremented by ‘1’ upon completion of each operation. This Address Pointer allows the entire memory contents to be serially read during one operation. The internal Address Pointer will automatically roll over from address FFF to address 000 if the host acknowledges the byte received from the array address FFF. Random Read Random read operations allow the host to access any memory location in a random manner. To perform this type of read operation, the word address must first be set. This is accomplished by sending the word address to the 24XX32A as part of a write operation (R/W bit set to ‘0’). Once the word address is sent, the host generates a Start condition following the Acknowledge. This terminates the write operation, but not before the internal Address Pointer is set. The host issues the control byte again, but with the R/W bit set to a ‘1’. The 24XX32A will then issue an Acknowledge and transmit the 8-bit data word. The host will not acknowledge the transfer, but does generate a Stop condition which causes the 24XX32A to discontinue transmission (Figure 8-2). After a random Read command, the internal Address Pointer will point to the address location following the one that was just read. FIGURE 8-1: CURRENT ADDRESS READ Bus Activity Host S T A R T SDA Line S 1 Control Byte 0 1 0 Bus Activity  2002-2021 Microchip Technology Inc. and its subsidiaries S T O P Data Byte A A A 1 2 1 0 P A C K N O A C K DS20001713N-page 11 24AA32A/24LC32A FIGURE 8-2: Bus Activity Host RANDOM READ S T A R T Control Byte Address High Byte AA xxxx S1 0 1 0 A 2100 A C Bus Activity K x = “don’t care” bit S T A R T Address Low Byte SDA Line FIGURE 8-3: Bus Activity Host A C K A C K Control Byte AA S1 0 1 0 A 2 1 01 S T O P Data Byte P N O A C K A C K SEQUENTIAL READ Control Byte Data n Data n + 1 Data n + 2 Data n + x S T O P P SDA Line Bus Activity DS20001713N-page 12 A C K A C K A C K A C K N O A C K  2002-2021 Microchip Technology Inc. and its subsidiaries 24AA32A/24LC32A 9.0 PACKAGING INFORMATION 9.1 Package Marking Information 8-Lead 2x3 DFN XXX YWW NN Example 264 134 13 8-Lead MSOP Example XXXXXT YWWNNN 4L32AI 13413F 8-Lead PDIP (300 mil) Example XXXXXXXX T/XXXNNN YYWW 8-Lead SOIC (3.90 mm) XXXXXXXT XXXXYYWW NNN 24LC32A I/P e3 13F 2134 Example 24LC32AI SN e3 2134 13F 8-Lead SOIJ (5.28 mm) Example XXXXXXXX T/XXXXXX YYWWNNN 24LC32A I/SM e3 213413F  2002-2021 Microchip Technology Inc. and its subsidiaries DS20001713N-page 13 24AA32A/24LC32A 5-Lead SOT-23 Example XXNN M613 8-Lead 2x3 TDFN XXX YWW NN 8-Lead TSSOP DS20001713N-page 14 Example A64 134 I3 Example XXXX 4LA TYWW I134 NNN 13F  2002-2021 Microchip Technology Inc. and its subsidiaries 24AA32A/24LC32A 1st Line Marking Codes Part Number TSSOP TSSOP X-Rotated MSOP 261 — 264 265 24AA32A 4AA 4AAX 4A32AT(1) 24LC32A 4LA 4LAX 4L32AT(1) Note 1: 2: DFN I Temp. TDFN E Temp. I Temp. SOT-23 E Temp. I Temp. A61 — B6NN(2) E Temp. — A64 A65 M6NN(2) N6NN(2) T = Temperature grade (I, E) NN = Alphanumeric traceability code Legend: XX...X T Y YY WW NNN e3 * Part number or part number code Temperature (I, E) Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Alphanumeric traceability code (2 characters for small packages) JEDEC® designator for Matte Tin (Sn) Standard OTP marking consists of Microchip part number, year code, week code, and traceability code. Note: For very small packages with no room for the JEDEC® designator e3 , the marking will only appear on the outer carton or reel label. Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information.  2002-2021 Microchip Technology Inc. and its subsidiaries DS20001713N-page 15 24AA32A/24LC32A /HDG3ODVWLF'XDO)ODW1R/HDG3DFNDJH0&[[PP%RG\>')1@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ ' $ % 1 '$780$ '$780% ( 127( ;  &  ;  &  7239,(:  & & $ $ 6($7,1* 3/$1( ; $  & 6,'(9,(: '  127(  & $ %   & $ % ( . / 1 ;E H %277209,(:   & $ % & 0LFURFKLS7HFKQRORJ\'UDZLQJ&5HY(6KHHWRI DS20001713N-page 16  2002-2021 Microchip Technology Inc. and its subsidiaries 24AA32A/24LC32A /HDG3ODVWLF'XDO)ODW1R/HDG3DFNDJH0&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‘9 &