DSC1004DI5-066.5800

DSC1004 Low-Power Precision CMOS Oscillator 1.8~3.3V General Description Features The DSC1004 is a silicon MEMS based CMOS oscillator offering excellent jitter and stability performance over a wide range of supply voltages and temperatures. The device operates from 1 to 150MHz with supply voltages between 1.8 to 3.3 Volts and extended temperatures from -40ºC to 105ºC. The DSC1004 has the same functionality and performance as the DSC1001 but with greater output drive (CL< 40pf). The DSC1004 incorporates an all silicon resonator that is extremely robust and nearly immune to stress related fractures, common to crystal based oscillators. Without sacrificing the performance and stability required of today’s systems, a crystal-less design allows for a higher level of reliability, making the DSC1004 ideal for rugged, industrial, and portable applications where stress, shock, and vibration can damage quartz crystal based systems. Available in industry standard packages, the DSC1004 can be “dropped-in” to the same PCB footprint as standard crystal oscillators.         Benefits   Block Diagram VDD Output Frequency Range: 1 to 150MHz Exceptional Stability over Temperature o ±10 PPM , ±25 PPM, ±50 PPM Operating voltage o 1.7 to 3.6V Operating Temperature Range o Ext. Industrial -40ºC to 105ºC o Industrial -40ºC to 85ºC o Ext. Commercial -20ºC to 70ºC o Commercial 0ºC to 70ºC Low Operating and Standby Current o 8mA Operating (40MHz) o 15uA Standby Ultra Miniature Footprint o 2.5 x 2.0 x 0.85 mm o 3.2 x 2.5 x 0.85 mm o 5.0 x 3.2 x 0.85 mm o 7.0 x 5.0 x 0.85 mm Excellent Shock and Vibration Resistance Lead Free, RoHS & Reach SVHC Compliant     Pin for pin “drop in” replacement for industry standard oscillators Semiconductor level reliability, significantly higher than quartz Short mass production lead-times Longer Battery Life / Reduced Power Compact Plastic package Cost Effective Applications Resonator      VCO PFD Frac-N PLL Standby#  Mobile Applications Consumer Electronics Portable Electronics CCD Clock for VTR Cameras Low Profile Applications Industrial GND (pin1) All Rights Reserved. No part of this document may be copied or reproduced in any form without the prior written permission of Micrel, Inc. Micrel Inc. may update or make changes to the contents, products, programs or services described at any time without notice. This document neither states nor implies any kind of warranty, including, but not limited to implied warranties of merchantability or fitness for a particular use. Page 1 MK-Q-B-P-D-083010-02-4 1.8~3.3V DSC1004 Low-Power Precision Oscillator Absolute Maximum Ratings1 Item Min. Max Unit Input Voltage -0.3 VDD+0.3 V Junction Temp - +150 °C Storage Temp -55 +150 °C Soldering Temp - +260 °C ESD HBM - DSC1004 Condition - 032.0000 T Family Package, Temp & Stability 40 sec max. Tape/ Reel Output Freq 1.0 to 150MHz V 4000 MM CDM CE1 200 1500 * See Ordering Information for details Ordering Code Recommended Operating Conditions Parameter Symbol Range Supply Voltage VDD 1.7 – 3.6V Output Load ZL R>10KΩ, C≤40pF Operating Temperature Option 1 Option 2 Option 3 Option 4 T -40 to +105 °C -40 to +85 °C -20 to +70 °C 0 to +70 °C Specifications (VDD = 1.8 to 3.3v) TA=850C unless otherwise specified Parameter Symbol Condition Min f0 Single Frequency 1 Frequency Tolerance Δf Includes frequency variations due to initial tolerance, temperature and power supply voltage Aging Δf Frequency Supply Current, standby Output Startup Time Output Disable Time 2 Max Unit 150 MHz ±10,±25,±50 ppm 1 year @25°C ±5 ppm IDD T=25°C 15 uA tSU T=25°C 1.0 1.3 ms 20 100 ns tDA Typ Output Duty Cycle SYM 45 55 % Input Logic Levels Input logic high Input logic low VIH VIL 0.75*VDD - 0.25* VDD Volts Notes: 1. Absolute maximum ratings are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated beyond these limits. 2. tSU is time to stable output frequency after VDD is applied. tSU and tEN (after EN is asserted) are identical values. 3. Measured over 50k clock cycles. All Rights Reserved. No part of this document may be copied or reproduced in any form without the prior written permission of Micrel, Inc. Micrel Inc. may update or make changes to the contents, products, programs or services described at any time without notice. This document neither states nor implies any kind of warranty, including, but not limited to implied warranties of merchantability or fitness for a particular use. Page 2 MK-Q-B-P-D-083010-02-4 DSC1004 1.8~3.3V Low-Power Precision Oscillator VDD = 1.8v Parameter Supply Current, no load Output Logic Levels Output logic high Output logic low Output Transition time Rise Time Fall Time Output Transition time Rise Time Fall Time Period Jitter Symbol IDD Condition 1MHz CL=0p 27MHz RL=∞ 70MHz T=25°C 150MHz VOH VOL -6mA 6mA tR tF CL=40pF; T=25°C 20%/80%*VDD tR tF Jp Min Typ 5.9 6.7 8.1 10.6 0.8*VDD - Max 6.2 7.1 8.5 11.9 Unit mA 0.2*VDD Volts 1.4 1.1 3 3 ns CL=40pF; T=25°C 10%/90%*VDD 2.2 1.8 4 4 ns F = 100MHz3 10 15 ps rms Typ 6.1 7.2 8.9 12.2 Max 6.4 7.5 9.4 13.9 Unit VDD = 2.5v Parameter Supply Current, no load Output Logic Levels Output logic high Output logic low Output Transition time Rise Time Fall Time Output Transition time Rise Time Fall Time Period Jitter Symbol IDD Condition 1MHz CL=0p 27MHz RL=∞ 70MHz T=25°C 150MHz VOH VOL -6mA 6mA tR tF CL=40pF; T=25°C 20%/80%*VDD tR tF Jp Min 0.9*VDD - mA 0.1*VDD Volts 1.0 0.9 2 2 ns CL=40pF; T=25°C 10%/90%*VDD 1.7 1.5 3.5 3 ns F = 100MHz3 5 10 ps rms Typ 6.2 7.6 10.0 14.4 Max 6.5 8.0 10.5 16.6 Unit VDD = 3.3v Parameter Supply Current, no load Output Logic Levels Output logic high Output logic low Output Transition time Rise Time Fall Time Output Transition time Rise Time Fall Time Period Jitter Symbol IDD Condition 1MHz CL=0p 27MHz RL=∞ 70MHz T=25°C 150MHz VOH VOL -8mA 8mA tR tF CL=40pF; T=25°C 20%/80%*VDD tR tF Jp Min 0.9*VDD - mA 0.1*VDD Volts 0.8 0.8 2 2 ns CL=40pF; T=25°C 10%/90%*VDD 1.4 1.3 3 3 ns F = 100MHz3 5 10 ps rms All Rights Reserved. No part of this document may be copied or reproduced in any form without the prior written permission of Micrel, Inc. Micrel Inc. may update or make changes to the contents, products, programs or services described at any time without notice. This document neither states nor implies any kind of warranty, including, but not limited to implied warranties of merchantability or fitness for a particular use. Page 3 MK-Q-B-P-D-083010-02-4 1.8~3.3V DSC1004 Low-Power Precision Oscillator Output Waveform tR tF VOH Output VOL tEN 1/fo tDA VIH Standby# VIL Standby Function Standby# Output (pin 1) (pin 3) Hi Level Output ON Open (no connect) Output ON Low Level High Impedance Test Circuit IDD VDD 0.01uF 4 3 1 2 40pF *VSD *VSD = Standby# Logic Level Input All Rights Reserved. No part of this document may be copied or reproduced in any form without the prior written permission of Micrel, Inc. Micrel Inc. may update or make changes to the contents, products, programs or services described at any time without notice. This document neither states nor implies any kind of warranty, including, but not limited to implied warranties of merchantability or fitness for a particular use. Page 4 MK-Q-B-P-D-083010-02-4 1.8~3.3V DSC1004 Low-Power Precision Oscillator Board Layout (recommended) Solder Reflow Profile 20-40 Sec MSL 1 @ 260°C refer to JSTD-020C Ramp-Up Rate (200°C to Peak Temp) 3°C/Sec Max. Preheat Time 150°C to 200°C 60-180 Sec Time maintained above 217°C 60-150 Sec 255-260°C Peak Temperature Time within 5°C of actual Peak 20-40 Sec 6°C/Sec Max. Ramp-Down Rate Time 25°C to Peak Temperature 8 min Max. Se 3C / 217°C 200°C 60-150 Sec S 6C/ ec 3C / Se cM ax . Reflow 25°C 60-180 Sec x. 150°C Ma Temperature (°C) cM ax . 260°C Cool Pre heat Time 8 min max Package Dimensions 7.0 x 5.0 mm Plastic Package External Dimensions 7.0±0.10 [0.276±0.004] #4 Recommended Land Pattern* 5.08 [0.200] 5.08 [0.2] #3 #4 #3 2.6 [0.102] 2.6 [0.102] 3.5 [0.138] 0.2 [0.008] 2.2 [0.087] #1 #2 5.0±0.10 [0.197±0.004] #2 1.4 [0.055] 0.2 [0.008] #1 0.85±0.05 [0.033±0.002] o o o o o 1.4 [0.055] 0.2 [0.008] 1.4 [0.055] 1.2 [0.047] No. 1 2 3 4 o Pin Terminal Standby# GND Output VDD *Note: The center pad is not connected internally and should be left unconnected or tied to GND. units: mm [inch] All Rights Reserved. No part of this document may be copied or reproduced in any form without the prior written permission of Micrel, Inc. Micrel Inc. may update or make changes to the contents, products, programs or services described at any time without notice. This document neither states nor implies any kind of warranty, including, but not limited to implied warranties of merchantability or fitness for a particular use. Page 5 MK-Q-B-P-D-083010-02-4 1.8~3.3V DSC1004 Low-Power Precision Oscillator 5.0 x 3.2 mm Plastic Package External Dimensions #3 2.54 [0.100] 2.54 [0.100] 5±0.10 [0.197±0.004] #4 Recommended Land Pattern #4 #3 2.1 [0.083] 1.2 [0.047] 0.2 [0.008] 0.1 [0.004] #2 1.2 [0.047] #1 #2 3.2±0.10 [0.126±0.004] 1.1 [0.043] #1 0.1 [0.004] 1.2 [0.047] 0.9 [0.035] No. 1 2 3 4 0.85±0.05 [0.033±0.002] Pin Terminal Standby# GND Output VDD units: mm [inch] 3.2 x 2.5 mm Plastic Package External Dimensions 3.2±0.05 [0.126±0.002] #4 Recommended Land Pattern 2.1 [0.083] 2.1 [0.083] #3 #3 #4 0.9 [0.035] 0.9 [.035] 1.0 [0.039] CO.25 #1 #2 2.5±0.05 [0.098±0.002] #2 0.9±0.05 [0.035±0.002] #1 0.8±0.1 [0.031±0.004] 0.85±0.05 [0.033±0.002] No. 1 2 3 4 Pin Terminal Standby# GND Output VDD 0.2 [0.008] 0.9 [0.035] units: mm [inch] All Rights Reserved. No part of this document may be copied or reproduced in any form without the prior written permission of Micrel, Inc. Micrel Inc. may update or make changes to the contents, products, programs or services described at any time without notice. This document neither states nor implies any kind of warranty, including, but not limited to implied warranties of merchantability or fitness for a particular use. Page 6 MK-Q-B-P-D-083010-02-4 1.8~3.3V DSC1004 Low-Power Precision Oscillator 2.5 x 2.0 mm Plastic Package External Dimensions 2.5±0.05 [0.098±0.002] #4 Recommended Land Pattern 1.65 [0.065] 1.65 [0.065] #3 #3 #4 0.7 [0.028] 0.7 [0.028] 0.85 [0.033] CO.25 #1 #2 2.0±0.05 [0.079±0.002] #2 0.65±0.05 [0.026±0.002] #1 0.2 [0.008] 0.65 [0.026] 0.65±0.10 [0.026±0.004] No .1 2 3 4 0.85±0.05 [0.033±0.002] Pin Terminal Standby# GND Output VDD units: mm [inch] Ordering Information DSC1004 PTS – xxx.xxxx T PART NUMBERING GUIDE Package (Plastic QFN) P=A: P=B: P=C: P=D: 7.0x5.0mm 5.0x3.2mm 3.2x2.5mm 2.5x2.0mm Temperature T=C: 0o ~ +70o C T=E: -20o ~ +70o C T=I: -40o ~ +85o C T=L: -40o ~ +105o C Stability Frequency S=1: ±50ppm S=2: ±25ppm S=5: ±10ppm XXX.XXXX - Packing Option Blank: Tubes T: Tape & Reel Example: DSC1004CE1–123.0000T The example part number above is a 123.0000MHz oscillator in Plastic 3.2x2.5mm package, with ±50ppm stability over an operating temperature of -20 to +70oC, shipped in Tape and Reel. Disclaimer: Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this data sheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel’s terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. MICREL, Inc. Phone: +1 (408) 944-0800 ● ● 2180 Fortune Drive, Fax: +1 (408) 474-1000 San Jose, California 95131 ● Email: hbwhelp@micrel.com ● ● USA www.micrel.com All Rights Reserved. No part of this document may be copied or reproduced in any form without the prior written permission of Micrel, Inc. Micrel Inc. may update or make changes to the contents, products, programs or services described at any time without notice. This document neither states nor implies any kind of warranty, including, but not limited to implied warranties of merchantability or fitness for a particular use. Page 7 MK-Q-B-P-D-083010-02-4