0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
DSPIC33CH64MP203-E/M5

DSPIC33CH64MP203-E/M5

  • 厂商:

    ACTEL(微芯科技)

  • 封装:

    UFQFN36

  • 描述:

    IC MCU 16BIT 88KB FLASH 36UQFN

  • 数据手册
  • 价格&库存
DSPIC33CH64MP203-E/M5 数据手册
dsPIC33CH128MP508 FAMILY 28/36/48/64/80-Pin Dual Core, 16-Bit Digital Signal Controllers with High-Resolution PWM and CAN Flexible Data (CAN FD) Operating Conditions Power Management • 3V to 3.6V, -40°C to +125°C: - Master Core: DC to 90 MIPS - Slave Core: DC to 100 MIPS • 3V to 3.6V, -40°C to +150°C: - Master Core: DC to 60 MIPS - Slave Core: DC to 60 MIPS • Low-Power Management Modes (Sleep, Idle, Doze) • Integrated Power-on Reset and Brown-out Reset Core: Dual 16-Bit dsPIC33CH CPU • Master/Slave Core Operation • Independent Peripherals for Master Core and Slave Core • Dual Partition for Slave PRAM LiveUpdate • Configurable Shared Resources for Master Core and Slave Core • Master Core with 64-128 Kbytes of Program Flash with ECC and 16K RAM • Slave Core with 24 Kbytes of Program RAM (PRAM) with ECC and 4K Data Memory RAM • Fast Six-Cycle Divide • Message Boxes and FIFO to Communicate Between Master and Slave (MSI) • Code Efficient (C and Assembly) Architecture • 40-Bit Wide Accumulators • Single-Cycle (MAC/MPY) with Dual Data Fetch • Single-Cycle, Mixed-Sign MUL Plus Hardware Divide • 32-Bit Multiply Support • Five Sets of Interrupt Context Selected Registers and Accumulators per Core for Fast Interrupt Response • Zero Overhead Looping Clock Management • • • • • • • • High-Resolution PWM with Fine Edge Placement • Up to 12 PWM Channels: - Four channels for Master - Eight channels for Slave • 250 ps PWM Resolution • Applications Include: - DC/DC Converters - AC/DC power supplies - Uninterruptable Power Supply (UPS) - Motor Control: BLDC, PMSM, SR, ACIM Timers/Output Compare/Input Capture • Two General Purpose 16-Bit Timers: - One each for Master and Slave • Peripheral Trigger Generator (PTG) Module: - One module for Master - Slave can interrupt on select PTG sources - Useful for automating complex sequences • 12 SCCP Modules: - Eight modules for Master - Four modules for Slave - Timer, Capture/Compare and PWM Modes - 16 or 32-bit time base - 16 or 32-bit capture - Four-deep capture buffer - Fully Asynchronous Operation, Available in Sleep Modes Internal Oscillator Programmable PLLs and Oscillator Clock Sources Master Reference Clock Output Slave Reference Clock Output Fail-Safe Clock Monitor (FSCM) Fast Wake-up and Start-up Backup Internal Oscillator LPRC Oscillator  2017-2019 Microchip Technology Inc. DS70005319D-page 1 dsPIC33CH128MP508 FAMILY Advanced Analog Features Other Features • Four ADC Modules: - One module for Master core - Three modules for Slave core - 12-bit, 3.5 Msps ADC - Up to 18 conversion channels • Four DAC/Analog Comparator Modules: - One module for Master core - Three modules for Slave core - 12-bit DACs with hardware slope compensation - 15 ns analog comparators • Three PGA Modules: - Three modules for Slave core - Can be read by Master ADC - Option to interface with Master ADC • Shared DAC/Analog Output: - DAC/analog comparator outputs - PGA outputs • PPS to Allow Function Remap • Programmable Cyclic Redundancy Check (CRC) for the Master • Two SENT Modules for the Master Communication Interfaces • Three UART Modules: - Two modules for Master core - One module for Slave core - Support for DMX and LIN/J2602 protocols • Three 4-Wire SPI/I2S Modules: - Two modules for Master core - One module for Slave core • CAN Flexible Data-Rate (FD) Module for the Master Core • Three I2C Modules: - Two modules for Master - One module for Slave - Support for SMBus Direct Memory Access (DMA) • Eight DMA Channels: - Six DMA channels available for the Master core - Two DMA channels available for the Slave core Debugger Development Support • In-Circuit and In-Application Programming • Simultaneous Debugging Support for Master and Slave Cores • Master Only Debug and Slave Only Debug Support • Master with Three Complex, Five Simple Breakpoints and Slave with One Complex, Two Simple Breakpoints • IEEE 1149.2 Compatible (JTAG) Boundary Scan • Trace Buffer and Run-Time Watch Safety Features • • • • • • • • • • DMT (Deadman Timer) ECC (Error Correcting Code) WDT (Watchdog Timer) CodeGuard™ Security CRC (Cyclic Redundancy Check) Two-Speed Start-up Fail-Safe Clock Monitoring Backup FRC (BFRC) Capless Internal Voltage Regulator Virtual Pins for Redundancy and Monitoring Qualification and Class B Support • AEC-Q100 REVG (Grade 1: -40°C to +125°C) Compliant • Class B Safety Library, IEC 60730 DS70005319D-page 2  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 1: MASTER AND SLAVE CORE FEATURES Feature Core Frequency Master Core Slave Core Shared 90 MIPS @ 180 MHz 100 MIPS @ 200 MHz — Program Memory 64K-128 Kbytes 24 Kbytes (PRAM)(2) — Internal Data RAM 16 Kbytes 4 Kbytes — 16-Bit Timer 1 1 — DMA 6 2 — SCCP (Capture/Compare/Timer) 8 4 — UART 2 1 — SPI/I2S 2 1 — I2C 2 1 — CAN FD 1 — — SENT 2 — — CRC 1 — — QEI 1 1 — PTG 1 — — CLC 4 4 — 16-Bit High-Speed PWM 4 8 — ADC 12-Bit 1 3 — Digital Comparator 4 4 — 12-Bit DAC/Analog CMP Module 1 3 — Watchdog Timer 1 1 — Deadman Timer 1 — — Input/Output 69 69 69 Simple Breakpoints 5 2 — PGAs(1) — 3 3 DAC Output Buffer — — 1 Oscillator 1 1 1 Note 1: Slave owns the peripheral/feature, but it is shared with the Master. 2: Dual Partition feature is available on Slave PRAM.  2017-2019 Microchip Technology Inc. DS70005319D-page 3 The device names, pin counts, memory sizes and peripheral availability of each device are listed in Table 2. The following pages show their pinout diagrams. Note 1: 2: PTG CRC PWM (High Resolution) Analog Comparators PGA Current Bias Source REFO 80 CLC Slave Master 64 QEI dsPIC33CH128MP508 Slave Master 64 I2C dsPIC33CH64MP508 Slave Master 48 SPI/I2S dsPIC33CH128MP506 Slave Master 48 UART  2017-2019 Microchip Technology Inc. dsPIC33CH64MP506 Slave Master 36 SENT dsPIC33CH128MP505 Slave Master 36 CAN FD dsPIC33CH64MP505 Slave Master 28 SCCP dsPIC33CH128MP503 Slave Master Timers dsPIC33CH64MP503 Slave Master 28 ADC Channels dsPIC33CH128MP502 Master 12-ADC Modules(2) dsPIC33CH64MP502 Core Data RAM Product Flash(1) dsPIC33CHXXXMP50X FAMILY Pins TABLE 2: 64K 16K 1 12 1 8 1 2 2 2 2 1 4 1 1 4 1 — 1 1 24K 128K 4K 16K 3 1 11 12 1 1 4 8 — 1 — 2 1 2 1 2 1 2 1 1 4 4 — 1 — 1 8 4 3 1 3 — — 1 1 1 24K 64K 4K 16K 3 1 11 15 1 1 4 8 — 1 — 2 1 2 1 2 1 2 1 1 4 4 — 1 — 1 8 4 3 1 3 — — 1 1 1 24K 128K 4K 16K 3 1 15 15 1 1 4 8 — 1 — 2 1 2 1 2 1 2 1 1 4 4 — 1 — 1 8 4 3 1 3 — — 1 1 1 24K 64K 4K 16K 3 1 16 16 1 1 4 8 — 1 — 2 1 2 1 2 1 2 1 1 4 4 — 1 — 1 8 4 3 1 3 — — 1 1 1 24K 128K 4K 16K 3 1 16 16 1 1 4 8 — 1 — 2 1 2 1 2 1 2 1 1 4 4 — 1 — 1 8 4 3 1 3 — — 1 1 1 24K 64K 4K 16K 3 1 16 16 1 1 4 8 — 1 — 2 1 2 1 2 1 2 1 1 4 4 — 1 — 1 8 4 3 1 3 — — 1 1 1 24K 128K 4K 16K 3 1 18 16 1 1 4 8 — 1 — 2 1 2 1 2 1 2 1 1 4 4 — 1 — 1 8 4 3 1 3 — — 1 1 1 24K 64K 4K 16K 3 1 18 16 1 1 4 8 — 1 — 2 1 2 1 2 1 2 1 1 4 4 — 1 — 1 8 4 3 1 3 — — 1 1 1 24K 128K 4K 16K 3 1 18 16 1 1 4 8 — 1 — 2 1 2 1 2 1 2 1 1 4 4 — 1 — 1 8 4 3 1 3 — — 1 1 1 — 1 1 1 1 4 — — 8 3 3 — 1 80 Slave 24K 4K 3 18 1 4 — For the Slave core, the implemented program memory of 24K is PRAM. Number of ADC modules implemented in the Master and Slave cores. dsPIC33CH128MP508 FAMILY DS70005319D-page 4 dsPIC33CH128MP508 PRODUCT FAMILIES dsPIC33CH128MP208 DS70005319D-page 5 Note 1: 2: Slave Master Slave 80 PWM (High Resolution) — 2 2 2 2 1 4 1 1 4 3 11 1 4 — — 1 1 1 1 4 — — 8 1 12 1 8 — 2 2 2 2 1 4 1 1 4 3 11 1 4 — — 1 1 1 1 4 — — 8 1 15 1 8 — 2 2 2 2 1 4 1 1 4 4K 3 15 1 4 — — 1 1 1 1 4 — — 8 16K 1 15 1 8 — 2 2 2 2 1 4 1 1 4 4K 3 16 1 4 — — 1 1 1 1 4 — — 8 16K 1 16 1 8 — 2 2 2 2 1 4 1 1 4 4K 3 16 1 4 — — 1 1 1 1 4 — — 8 16K 1 16 1 8 — 2 2 2 2 1 4 1 1 4 4K 3 16 1 4 — — 1 1 1 1 4 — — 8 16K 1 16 1 8 — 2 2 2 2 1 4 1 1 4 4K 3 18 1 4 — — 1 1 1 1 4 — — 8 16K 1 16 1 8 — 2 2 2 2 1 4 1 1 4 4K 3 18 1 4 — — 1 1 1 1 4 — — 8 16K 1 16 1 8 — 2 2 2 2 1 4 1 1 4 24K 4K 128K 16K 24K 4K 64K 16K 24K 128K 24K 64K 24K 128K 24K 64K 24K 128K 24K 64K REFO CRC 8 Current Bias Source PTG 1 PGA CLC 12 16K Analog Comparators QEI 80 I2C Slave Master 64 SPI/I2S dsPIC33CH64MP208 Slave Master 64 UART dsPIC33CH128MP206 Slave Master 48 SENT dsPIC33CH64MP206 Slave Master 48 CAN FD dsPIC33CH128MP205 Slave Master 36 SCCP dsPIC33CH64MP205 Slave Master 36 Timers dsPIC33CH128MP203 Slave Master 28 1 64K 1 — 1 1 3 3 — 1 1 — 1 1 3 3 — 1 1 — 1 1 3 3 — 1 1 — 1 1 3 3 — 1 1 — 1 1 3 3 — 1 1 — 1 1 3 3 — 1 1 — 1 1 3 3 — 1 1 — 1 1 3 3 — 1 1 — 1 1 24K 4K 3 18 1 4 — — 1 1 1 1 4 — — 8 3 3 — 1 128K 16K 1 16 1 8 — 2 2 2 2 1 4 1 1 4 1 — 1 1 24K 4K 3 18 1 4 — — 1 1 1 1 4 — — 8 3 3 — 1 For the Slave core, the implemented program memory of 24K is PRAM. Number of ADC modules implemented in the Master and Slave cores. dsPIC33CH128MP508 FAMILY dsPIC33CH64MP203 Slave Master 28 ADC Channels dsPIC33CH128MP202 Master Data RAM dsPIC33CH64MP202 Core Flash(1) Product ADC Modules(2) dsPIC33CHXXXMP20X FAMILY WITH NO CAN FD Pins  2017-2019 Microchip Technology Inc. TABLE 3: dsPIC33CH128MP508 FAMILY Pin Diagrams RA1 RA2 RA3 RA4 AVDD AVSS VDD VSS RB0 RB1 RB2 RB3 RB4 RB5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 dsPIC33CHXXXMP502 dsPIC33CHXXXMP202 28-Pin SSOP(1) 28 27 26 25 24 23 22 21 20 19 18 17 16 15 RA0 MCLR RB15 RB14 RB13 RB12 RB11 RB10 VDD VSS RB9 RB8 RB7 RB6 Note 1: Shaded pins are up to 5.5 VDC tolerant (refer to Table 3-29). For the list of analog ports, refer to Table 3-28 and Table 4-25. TABLE 4: 28-PIN SSOP Pin # Master Core Slave Core 1 AN1/RA1 S1AN15/S1RA1 2 AN2/RA2 S1AN16/S1RA2 3 AN3/IBIAS0/RA3 S1AN0/S1CMP1A/S1PGA1P1/S1RA3 4 AN4/IBIAS1/RA4 S1MCLR3/S1AN1/S1CMP2A/S1PGA2P1/S1PGA3P2/S1RA4 5 AVDD AVDD 6 AVSS AVSS 7 VDD VDD 8 VSS VSS 9 OSCI/CLKI/AN5/RP32/RB0 S1AN5/S1RP32/S1RB0 10 OSCO/CLKO/AN6/IBIAS2/RP33/RB1(2) S1AN4/S1RP33/S1RB1(2) 11 DACOUT1/AN7/CMP1D/RP34/INT0/RB2 S1MCLR2/S1AN3/S1ANC0/S1ANC1/S1CMP1D/S1CMP2D/S1CMP3D/ S1RP34/S1INT0/S1RB2 12 PGD2/AN8/RP35/RB3 S1PGD2/S1AN18/S1CMP3A/S1PGA3P1/S1RP35/S1RB3 13 PGC2/RP36/RB4 S1PGC2/S1AN9/S1RP36/S1PWM5L/S1RB4 14 PGD3/RP37/SDA2/RB5 S1PGD3/S1RP37/S1RB5 15 PGC3/RP38/SCL2/RB6 S1PGC3/S1RP38/S1RB6 16 TDO/AN9/RP39/RB7 S1MCLR1/S1AN6/S1RP39/S1PWM5H/S1RB7 17 PGD1/AN10/RP40/SCL1/RB8 S1PGD1/S1AN7/S1RP40/S1SCL1/S1RB8 18 PGC1/AN11/RP41/SDA1/RB9 S1PGC1/S1RP41/S1SDA1/S1RB9 19 VSS VSS 20 VDD VDD 21 TMS/RP42/PWM3H/RB10(1) S1RP42/S1PWM3H/S1RB10(1) 22 TCK/RP43/PWM3L/RB11 S1RP43/S1PWM8H/S1PWM3L/S1RB11 23 TDI/RP44/PWM2H/RB12 S1RP44/S1PWM2H/S1RB12 24 RP45/PWM2L/RB13 S1RP45/S1PWM7H/S1PWM2L/S1RB13 25 RP46/PWM1H/RB14 S1RP46/S1PWM1H/S1RB14 26 RP47/PWM1L/RB15 S1RP47/S1PWM6H/S1PWM1L/S1RB15 27 MCLR 28 AN0/CMP1A/RA0 — S1RA0 Legend: RPn represents remappable peripheral functions. Note 1: A pull-up resistor is connected to this pin during programming. 2: This pin is toggled during programming. DS70005319D-page 6  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY VSS RB9 VDD RB10 RB11 RB13 28-Pin UQFN(1,2) RB12 Pin Diagrams (Continued) 28 27 26 25 24 23 22 RB14 1 21 RB8 RB15 2 20 RB7 MCLR 3 RB6 RA0 4 RA1 5 19 dsPIC33CHXXXMP502 dsPIC33CHXXXMP202 18 17 RA2 6 16 RB3 RA3 7 15 RB2 RB5 RB4 RB1 RB0 VSS VDD AVSS RA4 AVDD 8 9 10 11 12 13 14 Note 1: Shaded pins are up to 5.5 VDC tolerant (refer to Table 3-29). For the list of analog ports, refer to Table 3-28 and Table 4-25. 2: The large center pad on the bottom of the package may be left floating or connected to VSS. The four-corner anchor pads are internally connected to the large bottom pad, and therefore, must be connected to the same net as the large center pad. TABLE 5: Pin # 28-PIN UQFN Master Core Slave Core 1 RP46/PWM1H/RB14 S1RP46/S1PWM1H/S1RB14 S1RP47/S1PWM6H/S1PWM1L/S1RB15 2 RP47/PWM1L/RB15 3 MCLR 4 AN0/CMP1A/RA0 AN1/RA1 S1RA0 S1AN15/S1RA1 AN2/RA2 AN3/IBIAS0/RA3 S1AN16/S1RA2 S1AN0/S1CMP1A/S1PGA1P1/S1RA3 5 6 7 — 8 AN4/IBIAS1/RA4 S1MCLR3/S1AN1/S1CMP2A/S1PGA2P1/S1PGA3P2/S1RA4 9 AVDD 10 AVSS AVDD AVSS 11 12 VDD VSS VDD VSS 13 14 OSCI/CLKI/AN5/RP32/RB0 OSCO/CLKO/AN6/IBIAS2/RP33/RB1(2) S1AN5/S1RP32/S1RB0 S1AN4/S1RP33/S1RB1(2) 15 16 DACOUT1/AN7/CMP1D/RP34/INT0/RB2 PGD2/AN8/RP35/RB3 S1MCLR2/S1AN3/S1ANC0/S1ANC1/S1CMP1D/S1CMP2D/S1CMP3D/S1RP34/S1INT0/S1RB2 S1PGD2/S1AN18/S1CMP3A/S1PGA3P1/S1RP35/S1RB3 17 18 PGC2/RP36/RB4 PGD3/RP37/SDA2/RB5 S1PGC2/S1AN9/S1RP36/S1PWM5L/S1RB4 S1PGD3/S1RP37/S1RB5 19 PGC3/RP38/SCL2/RB6 S1PGC3/S1RP38/S1RB6 20 TDO/AN9/RP39/RB7 S1MCLR1/S1AN6/S1RP39/S1PWM5H/S1RB7 21 22 PGD1/AN10/RP40/SCL1/RB8 PGC1/AN11/RP41/SDA1/RB9 S1PGD1/S1AN7/S1RP40/S1SCL1/S1RB8 S1PGC1/S1RP41/S1SDA1/S1RB9 23 VSS 24 VDD VSS VDD 25 26 TMS/RP42/PWM3H/RB10(1) TCK/RP43/PWM3L/RB11 S1RP42/S1PWM3H/S1RB10(1) S1RP43/S1PWM8H/S1PWM3L/S1RB11 27 TDI/RP44/PWM2H/RB12 RP45/PWM2L/RB13 S1RP44/S1PWM2H/S1RB12 S1RP45/S1PWM7H/S1PWM2L/S1RB13 28 Legend: RPn represents remappable peripheral functions. Note 1: A pull-up resistor is connected to this pin during programming. 2: This pin is toggled during programming.  2017-2019 Microchip Technology Inc. DS70005319D-page 7 dsPIC33CH128MP508 FAMILY Pin Diagrams (Continued) RB9 RC4 RC5 VSS VDD RB10 RB11 RB12 RB13 36-Pin UQFN(1,2) RB14 1 36 35 34 33 32 31 30 29 28 27 RB8 RB15 2 26 RB7 MCLR 3 25 RB6 RC0 4 24 RB5 RA0 5 23 VDD RA1 6 22 VSS 7 21 RB4 RA3 8 20 RB3 RA4 9 19 RB2 RA2 dsPIC33CHXXXMP503 dsPIC33CHXXXMP203 RB1 RB0 RC3 VSS VDD RC2 AVSS RC1 AVDD 10 11 12 13 14 15 16 17 18 Note 1: Shaded pins are up to 5.5 VDC tolerant (refer to Table 3-29). For the list of analog ports, refer to Table 3-28 and Table 4-25. 2: The large center pad on the bottom of the package may be left floating or connected to VSS. The four-corner anchor pads are internally connected to the large bottom pad, and therefore, must be connected to the same net as the large center pad. DS70005319D-page 8  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 6: 36-PIN UQFN Pin # Master Core Slave Core 1 RP46/PWM1H/RB14 S1RP46/S1PWM1H/S1RB14 2 RP47/PWM1L/RB15 S1RP47/S1PWM6H/S1PWM1L/S1RB15 3 MCLR 4 AN12/IBIAS3/RP48/RC0 S1AN10/S1RP48/S1RC0 — 5 AN0/CMP1A/RA0 S1RA0 6 AN1/RA1 S1AN15/S1RA1 7 AN2/RA2 S1AN16/S1RA2 8 AN3/IBIAS0/RA3 S1AN0/S1CMP1A/S1PGA1P1/S1RA3 9 AN4/IBIAS1/RA4 S1MCLR3/S1AN1/S1CMP2A/S1PGA2P1/S1PGA3P2/S1RA4 10 AVDD AVDD 11 AVSS AVSS 12 AN13/ISRC0/RP49/RC1 S1ANA1/S1RP49/S1RC1 13 AN14/ISRC1/RP50/RC2 S1ANA0/S1RP50/S1RC2 14 VDD VDD 15 VSS VSS 16 CMP1B/RP51/RC3 S1AN8/S1CMP3B/S1RP51/S1RC3 17 OSCI/CLKI/AN5/RP32/RB0 S1AN5/S1RP32/S1RB0 18 OSCO/CLKO/AN6/IBIAS2/RP33/RB1(2) S1AN4/S1RP33/S1RB1(2) 19 DACOUT1/AN7/CMP1D/RP34/INT0/RB2 S1MCLR2/S1AN3/S1ANC0/S1ANC1/S1CMP1D/S1CMP2D/S1CMP3D/ S1RP34/S1INT0/S1RB2 20 PGD2/AN8/RP35/RB3 S1PGD2/S1AN18/S1CMP3A/S1PGA3P1/S1RP35/S1RB3 21 PGC2/RP36/RB4 S1PGC2/S1AN9/S1RP36/S1PWM5L/S1RB4 22 VSS VSS 23 VDD VDD 24 PGD3/RP37/SDA2/RB5 S1PGD3/S1RP37/S1RB5 25 PGC3/RP38/SCL2/RB6 S1PGC3/S1RP38/S1RB6 26 TDO/AN9/RP39/RB7 S1MCLR1/S1AN6/S1RP39/S1PWM5H/S1RB7 27 PGD1/AN10/RP40/SCL1/RB8 S1PGD1/S1AN7/S1RP40/S1SCL1/S1RB8 28 PGC1/AN11/RP41/SDA1/RB9 S1PGC1/S1RP41/S1SDA1/S1RB9 29 RP52/RC4 S1RP52/S1PWM2H/S1RC4 30 RP53/RC5 S1RP53/S1PWM2L/S1RC5 31 VSS VSS 32 VDD VDD 33 TMS/RP42/PWM3H/RB10(1) S1RP42/S1PWM3H/S1RB10(1) 34 TCK/RP43/PWM3L/RB11 S1RP43/S1PWM8H/S1PWM3L/S1RB11 35 TDI/RP44/PWM2H/RB12 S1RP44/S1PWM7L/S1RB12 36 RP45/PWM2L/RB13 S1RP45/S1PWM7H/S1RB13 Legend: RPn represents remappable peripheral functions. Note 1: A pull-up resistor is connected to this pin during programming. 2: This pin is toggled during programming.  2017-2019 Microchip Technology Inc. DS70005319D-page 9 dsPIC33CH128MP508 FAMILY Pin Diagrams (Continued) RC4 RB9 RC5 RC10 RC11 VSS VDD RD1 RB11 RB10 RB12 RB13 48-Pin TQFP/UQFN(1,2) 48 47 46 45 44 43 42 41 40 39 38 37 RB14 1 36 RB8 RB15 2 35 RB7 RC12 RC13 3 34 4 33 RB6 RB5 MCLR 5 32 VDD RD13 6 31 VSS RC0 7 30 RD8 RA0 RA1 RA2 8 29 RC9 9 28 RC8 10 27 RB4 RA3 11 26 RB3 RA4 12 25 RB2 dsPIC33CHXXXMP505 dsPIC33CHXXXMP205 RD10 RC7 RB1 RB0 RC3 VSS VDD RC6 RC2 RC1 AVSS AVDD 13 14 15 16 17 18 19 20 21 22 23 24 Note 1: Shaded pins are up to 5.5 VDC tolerant (refer to Table 3-29). For the list of analog ports, refer to Table 3-28 and Table 4-25. 2: The large center pad on the bottom of the package may be left floating or connected to VSS. The four-corner anchor pads are internally connected to the large bottom pad, and therefore, must be connected to the same net as the large center pad. DS70005319D-page 10  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 7: 48-PIN TQFP/UQFN Pin # Master Core Slave Core 1 RP46/PWM1H/RB14 S1RP46/S1PWM6L/S1RB14 2 RP47/PWM1L/RB15 S1RP47/S1PWM6H/S1RB15 3 RP60/RC12 S1RP60/S1PWM3H/S1RC12 4 RP61/RC13 S1RP61/S1PWM3L/S1RC13 5 MCLR 6 RD13 S1ANN0/S1PGA1N2/S1RD13 — 7 AN12/IBIAS3/RP48/RC0 S1AN10/S1RP48/S1RC0 8 AN0/CMP1A/RA0 S1RA0 9 AN1/RA1 S1AN15/S1RA1 10 AN2/RA2 S1AN16/S1RA2 11 AN3/IBIAS0/RA3 S1AN0/S1CMP1A/S1PGA1P1/S1RA3 12 AN4/IBIAS1/RA4 S1MCLR3/S1AN1/S1CMP2A/S1PGA2P1/S1PGA3P2/S1RA4 13 AVDD AVDD 14 AVSS AVSS 15 AN13/ISRC0/RP49/RC1 S1ANA1/S1RP49/S1RC1 16 AN14/ISRC1/RP50/RC2 S1ANA0/S1RP50/S1RC2 17 RP54/RC6 S1AN11/S1CMP1B/S1RP54/S1RC6 18 VDD VDD 19 VSS VSS 20 CMP1B/RP51/RC3 S1AN8/S1CMP3B/S1RP51/S1RC3 21 OSCI/CLKI/AN5/RP32/RB0 S1AN5/S1RP32/S1RB0 22 OSCO/CLKO/AN6/IBIAS2/RP33/RB1(2) S1AN4/S1RP33/S1RB1(2) 23 ISRC3/RD10 S1AN13/S1CMP2B/S1RD10 24 AN15/ISRC2/RP55/RC7 S1AN12/S1RP55/S1RC7 25 DACOUT1/AN7/CMP1D/RP34/INT0/RB2 S1MCLR2/S1AN3/S1ANC0/S1ANC1/S1CMP1D/S1CMP2D/S1CMP3D/S1RP34/ S1INT0/S1RB2 26 PGD2/AN8/RP35/RB3 S1PGD2/S1AN18/S1CMP3A/S1PGA3P1/S1RP35/S1RB3 27 PGC2/RP36/RB4 S1PGC2/S1AN9/S1RP36/S1PWM5L/S1RB4 28 RP56/ASDA1/SCK2/RC8 S1RP56/S1ASDA1/S1SCK1/S1RC8 29 RP57/ASCL1/SDI2/RC9 S1RP57/S1ASCL1/S1SDI1/S1RC9 30 SDO2/PCI19/RD8 S1SDO1/S1PCI19/S1RD8 31 VSS VSS 32 VDD VDD 33 PGD3/RP37/SDA2/RB5 S1PGD3/S1RP37/S1RB5 34 PGC3/RP38/SCL2/RB6 S1PGC3/S1RP38/S1RB6 35 TDO/AN9/RP39/RB7 S1MCLR1/S1AN6/S1RP39/S1PWM5H/S1RB7 36 PGD1/AN10/RP40/SCL1/RB8 S1PGD1/S1AN7/S1RP40/S1SCL1/S1RB8 37 PGC1/AN11/RP41/SDA1/RB9 S1PGC1/S1RP41/S1SDA1/S1RB9 38 RP52/RC4 S1RP52/S1PWM2H/S1RC4 39 RP53/RC5 S1RP53/S1PWM2L/S1RC5 40 RP58/RC10 S1RP58/S1PWM1H/S1RC10 41 RP59/RC11 S1RP59/S1PWM1L/S1RC11 42 VSS VSS 43 VDD VDD 44 RP65/RD1 S1RP65/S1PWM4H/S1RD1 45 TMS/RP42/PWM3H/RB10(1) S1RP42/S1PWM8L/S1RB10(1) 46 TCK/RP43/PWM3L/RB11 S1RP43/S1PWM8H/S1RB11 47 TDI/RP44/PWM2H/RB12 S1RP44/S1PWM7L/S1RB12 48 RP45/PWM2L/RB13 S1RP45/S1PWM7H/S1RB13 Legend: RPn represents remappable peripheral functions. Note 1: A pull-up resistor is connected to this pin during programming. 2: This pin is toggled during programming.  2017-2019 Microchip Technology Inc. DS70005319D-page 11 dsPIC33CH128MP508 FAMILY Pin Diagrams (Continued) 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 RB13 RB12 RB11 RB10 RD0 RD1 RD2 VDD VSS RD3 RD4 RC11 RC10 RC5 RC4 RB9 64-Pin TQFP/QFN(1,2) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 dsPIC33CHXXXMP506 dsPIC33CHXXXMP206 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 RB8 RB7 RB6 RB5 RD5 RD6 RD7 VDD Vss RD8 RD9 RC9 RC8 RB4 RB3 RB2 RA3 RA4 AVDD AVSS RD12 RC1 RC2 RC6 VDD VSS RC3 RB0 RB1 RD11 RD10 RC7 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 RB14 RB15 RC12 RC13 RC14 RC15 MCLR RD15 VSS VDD RD14 RD13 RC0 RA0 RA1 RA2 Note 1: Shaded pins are up to 5.5 VDC tolerant (refer to Table 3-29). For the list of analog ports, refer to Table 3-28 and Table 4-25. 2: The large center pad on the bottom of the package may be left floating or connected to VSS. The four-corner anchor pads are internally connected to the large bottom pad, and therefore, must be connected to the same net as the large center pad. DS70005319D-page 12  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 8: 64-PIN TQFP/QFN Pin # Master Core Slave Core 1 RP46/PWM1H/RB14 S1RP46/S1RB14 S1RP47/S1RB15 2 RP47/PWM1L/RB15 3 RP60/PWM4H/RC12 S1RP60/S1RC12 4 RP61/PWM4L/RC13 S1RP61/S1RC13 5 RP62/RC14 S1RP62/S1PWM7H/S1RC14 6 RP63/RC15 S1RP63/S1PWM7L/S1RC15 7 MCLR 8 PCI22/RD15 S1PCI22/S1RD15 — 9 VSS VSS 10 VDD VDD 11 PCI21/RD14 S1ANN1/S1PGA2N2/S1PCI21/S1RD14 12 RD13 S1ANN0/S1PGA1N2/S1RD13 13 AN12/IBIAS3/RP48/RC0 S1AN10/S1RP48/S1RC0 14 AN0/CMP1A/RA0 S1RA0 15 AN1/RA1 S1AN15/S1RA1 16 AN2/RA2 S1AN16/S1RA2 17 AN3/IBIAS0/RA3 S1AN0/S1CMP1A/S1PGA1P1/S1RA3 18 AN4/IBIAS1/RA4 S1MCLR3/S1AN1/S1CMP2A/S1PGA2P1/S1PGA3P2/S1RA4 19 AVDD AVDD 20 AVSS AVSS 21 RD12 S1AN14/S1PGA2P2/S1RD12 22 AN13/ISRC0/RP49/RC1 S1ANA1/S1RP49/S1RC1 23 AN14/ISRC1/RP50/RC2 S1ANA0/S1RP50/S1RC2 24 RP54/RC6 S1AN11/S1CMP1B/S1RP54/S1RC6 25 VDD VDD 26 VSS VSS 27 CMP1B/RP51/RC3 S1AN8/S1CMP3B/S1RP51/S1RC3 28 OSCI/CLKI/AN5/RP32/RB0 S1AN5/S1RP32/S1RB0 29 OSCO/CLKO/AN6/IBIAS2/RP33/RB1(2) S1AN4/S1RP33/S1RB1(2) 30 RD11 S1AN17/S1PGA1P2/S1RD11 31 ISRC3/RD10 S1AN13/S1CMP2B/S1RD10 32 AN15/ISRC2/RP55/RC7 S1AN12/S1RP55/S1RC7 33 DACOUT1/AN7/CMP1D/RP34/INT0/RB2 S1MCLR2/S1AN3/S1ANC0/S1ANC1/S1CMP1D/S1CMP2D/S1CMP3D/S1RP34/ S1INT0/S1RB2 34 PGD2/AN8/RP35/RB3 S1PGD2/S1AN18/S1CMP3A/S1PGA3P1/S1RP35/S1RB3 35 PGC2/RP36/RB4 S1PGC2/S1AN9/S1RP36/S1PWM5L/S1RB4 36 RP56/ASDA1/SCK2/RC8 S1RP56/S1ASDA1/S1SCK1/S1RC8 37 RP57/ASCL1/SDI2/RC9 S1RP57/S1ASCL1/S1SDI1/S1RC9 38 PCI20/RD9 S1PCI20/S1RD9 39 SDO2/PCI19/RD8 S1SDO1/S1PCI19/S1RD8 40 VSS VSS 41 VDD VDD 42 RP71/RD7 S1RP71/S1PWM8H/S1RD7 43 RP70/RD6 S1RP70/S1PWM6H/S1RD6 44 RP69/RD5 S1RP69/S1PWM6L/S1RD5 45 PGD3/RP37/SDA2/RB5 S1PGD3/S1RP37/S1RB5 46 PGC3/RP38/SCL2/RB6 S1PGC3/S1RP38/S1RB6 47 TDO/AN9/RP39/RB7 S1MCLR1/S1AN6/S1RP39/S1PWM5H/S1RB7 48 PGD1/AN10/RP40/SCL1/RB8 S1PGD1/S1AN7/S1RP40/S1SCL1/S1RB8 49 PGC1/AN11/RP41/SDA1/RB9 S1PGC1/S1RP41/S1SDA1/S1RB9 50 RP52/RC4 S1RP52/S1PWM2H/S1RC4 Legend: RPn represent remappable peripheral functions. Note 1: A pull-up resistor is connected to this pin during programming. 2: This pin is toggled during programming.  2017-2019 Microchip Technology Inc. DS70005319D-page 13 dsPIC33CH128MP508 FAMILY TABLE 8: 64-PIN TQFP/QFN (CONTINUED) Pin # Master Core Slave Core 51 RP53/RC5 S1RP53/S1PWM2L/S1RC5 52 RP58/RC10 S1RP58/S1PWM1H/S1RC10 53 RP59/RC11 S1RP59/S1PWM1L/S1RC11 54 RP68/RD4 S1RP68/S1PWM3H/S1RD4 55 RP67/RD3 S1RP67/S1PWM3L/S1RD3 56 VSS VSS 57 VDD VDD 58 RP66/RD2 S1RP66/S1PWM8L/S1RD2 59 RP65/RD1 S1RP65/S1PWM4H/S1RD1 60 RP64/RD0 S1RP64/S1PWM4L/S1RD0 61 TMS/RP42/PWM3H/RB10(1) S1RP42/S1RB10(1) 62 TCK/RP43/PWM3L/RB11 S1RP43/S1RB11 63 TDI/RP44/PWM2H/RB12 S1RP44/S1RB12 64 RP45/PWM2L/RB13 S1RP45/S1RB13 Legend: RPn represent remappable peripheral functions. Note 1: A pull-up resistor is connected to this pin during programming. 2: This pin is toggled during programming. DS70005319D-page 14  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY Pin Diagrams (Continued) dsPIC33CHXXXMP508 dsPIC33CHXXXMP208 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 RB8 RE11 RB7 RE10 RB6 RB5 RD5 RD6 RD7 VDD VSS RD8 RD9 RC9 RC8 RB4 RE9 RB3 RE8 RB2 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 RA3 RE4 RA4 RE5 AVDD AVSS RD12 RC1 RC2 RC6 VDD VSS RC3 RB0 RB1 RD11 RE6 RD10 RE7 RC7 RB14 RE0 RB15 RE1 RC12 RC13 RC14 RC15 MCLR RD15 VSS VDD RD14 RD13 RC0 RA0 RE2 RA1 RE3 RA2 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 RB13 RE15 RB12 RE14 RB11 RB10 RD0 RD1 RD2 VDD VSS RD3 RD4 RC11 RC10 RC5 RE13 RC4 RE12 RB9 80-Pin TQFP(1) Note 1: Shaded pins are up to 5.5 VDC tolerant (refer to Table 3-29). For the list of analog ports, refer to Table 3-28 and Table 4-25.  2017-2019 Microchip Technology Inc. DS70005319D-page 15 dsPIC33CH128MP508 FAMILY TABLE 9: 80-PIN TQFP Pin # Master Core Slave Core 1 RP46/PWM1H/RB14 S1RP46/S1RB14 2 RE0 S1RE0 3 RP47/PWM1L/RB15 S1RP47/S1RB15 4 RE1 S1RE1 5 RP60/PWM4H/RC12 S1RP60/S1RC12 6 RP61/PWM4L/RC13 S1RP61/S1RC13 7 RP62/RC14 S1RP62/S1PWM7H/S1RC14 8 RP63/RC15 S1RP63/S1PWM7L/S1RC15 9 MCLR 10 PCI22/RD15 S1PCI22/S1RD15 — 11 VSS VSS 12 VDD VDD 13 PCI21/RD14 S1ANN1/S1PGA2N2/S1PCI21/S1RD14 14 RD13 S1ANN0/S1PGA1N2/S1RD13 15 AN12/IBIAS3/RP48/RC0 S1AN10/S1RP48/S1RC0 16 AN0/CMP1A/RA0 S1RA0 17 RE2 S1RE2 18 AN1/RA1 S1AN15/S1RA1 19 RE3 S1RE3 20 AN2/RA2 S1AN16/S1RA2 21 AN3/IBIAS0/RA3 S1AN0/S1CMP1A/S1PGA1P1/S1RA3 22 RE4 S1RE4 23 AN4/IBIAS1/RA4 S1MCLR3/S1AN1/S1CMP2A/S1PGA2P1/S1PGA3P2/S1RA4 24 RE5 S1RE5 25 AVDD AVDD 26 AVSS AVSS 27 RD12 S1AN14/S1PGA2P2/S1RD12 28 AN13/ISRC0/RP49/RC1 S1ANA1/S1RP49/S1RC1 29 AN14/ISRC1/RP50/RC2 S1ANA0/S1RP50/S1RC2 30 RP54/RC6 S1AN11/S1CMP1B/S1RP54/S1RC6 31 VDD VDD 32 VSS VSS 33 CMP1B/RP51/RC3 S1AN8/S1CMP3B/S1RP51/S1RC3 34 OSCI/CLKI/AN5/RP32/RB0 S1AN5/S1RP32/S1RB0 35 OSCO/CLKO/AN6/IBIAS2/RP33/RB1(2) S1AN4/S1RP33/S1RB1(2) 36 RD11 S1AN17/S1PGA1P2/S1RD11 37 RE6 S1PGA3N2/S1RE6 38 ISRC3/RD10 S1AN13/S1CMP2B/S1RD10 39 RE7 S1RE7 40 AN15/ISRC2/RP55/RC7 S1AN12/S1RP55/S1RC7 41 DACOUT1/AN7/CMP1D/RP34/INT0/RB2 S1MCLR2/S1AN3/S1ANC0/S1ANC1/S1CMP1D/S1CMP2D/S1CMP3D/S1RP34/ S1INT0/S1RB2 42 RE8 S1RE8 43 PGD2/AN8/RP35/RB3 S1PGD2/S1AN18/S1CMP3A/S1PGA3P1/S1RP35/S1RB3 44 RE9 S1RE9 45 PGC2/RP36/RB4 S1PGC2/S1AN9/S1RP36/S1PWM5L/S1RB4 46 RP56/ASDA1/SCK2/RC8 S1RP56/S1ASDA1/S1SCK1/S1RC8 47 RP57/ASCL1/SDI2/RC9 S1RP57/S1ASCL1/S1SDI1/S1RC9 48 PCI20/RD9 S1PCI20/S1RD9 Legend: RPn represent remappable peripheral functions. Note 1: A pull-up resistor is connected to this pin during programming. 2: This pin is toggled during programming. DS70005319D-page 16  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 9: 80-PIN TQFP (CONTINUED) Pin # Master Core Slave Core 49 SDO2/PCI19/RD8 S1SDO1/S1PCI19/S1RD8 50 VSS VSS 51 VDD VDD 52 RP71/RD7 S1RP71/S1PWM8H/S1RD7 53 RP70/RD6 S1RP70/S1PWM6H/S1RD6 54 RP69/RD5 S1RP69/S1PWM6L/S1RD5 55 PGD3/RP37/SDA2/RB5 S1PGD3/S1RP37/S1RB5 56 PGC3/RP38/SCL2/RB6 S1PGC3/S1RP38/S1RB6 57 RE10 S1RE10 58 TDO/AN9/RP39/RB7 S1MCLR1/S1AN6/S1RP39/S1PWM5H/S1RB7 59 RE11 S1RE11 60 PGD1/AN10/RP40/SCL1/RB8 S1PGD1/S1AN7/S1RP40/S1SCL1/S1RB8 61 PGC1/AN11/RP41/SDA1/RB9 S1PGC1/S1RP41/S1SDA1/S1RB9 62 ASCL2/RE12 S1RE12 63 RP52/RC4 S1RP52/S1PWM2H/S1RC4 64 ASDA2/RE13 S1RE13 65 RP53/RC5 S1RP53/S1PWM2L/S1RC5 66 RP58/RC10 S1RP58/S1PWM1H/S1RC10 67 RP59/RC11 S1RP59/S1PWM1L/S1RC11 68 RP68/RD4 S1RP68/S1PWM3H/S1RD4 69 RP67/RD3 S1RP67/S1PWM3L/S1RD3 70 VSS VSS 71 VDD VDD 72 RP66/RD2 S1RP66/S1PWM8L/S1RD2 73 RP65/RD1 S1RP65/S1PWM4H/S1RD1 74 RP64/RD0 S1RP64/S1PWM4L/S1RD0 75 TMS/RP42/PWM3H/RB10(1) S1RP42/S1RB10(1) 76 TCK/RP43/PWM3L/RB11 S1RP43/S1RB11 77 RE14 S1RE14 78 TDI/RP44/PWM2H/RB12 S1RP44/S1RB12 79 RE15 S1RE15 80 RP45/PWM2L/RB13 S1RP45/S1RB13 Legend: RPn represent remappable peripheral functions. Note 1: A pull-up resistor is connected to this pin during programming. 2: This pin is toggled during programming.  2017-2019 Microchip Technology Inc. DS70005319D-page 17 dsPIC33CH128MP508 FAMILY Table of Contents 1.0 Device Overview ........................................................................................................................................................................ 21 2.0 Guidelines for Getting Started with 16-Bit Digital Signal Controllers .......................................................................................... 29 3.0 Master Modules .......................................................................................................................................................................... 35 4.0 Slave Modules .......................................................................................................................................................................... 259 5.0 Master Slave Interface (MSI).................................................................................................................................................... 415 6.0 Oscillator with High-Frequency PLL ......................................................................................................................................... 429 7.0 Power-Saving Features (Master and Slave) ............................................................................................................................ 471 8.0 Direct Memory Access (DMA) Controller ................................................................................................................................. 489 9.0 High-Resolution PWM (HSPWM) with Fine Edge Placement .................................................................................................. 499 10.0 Capture/Compare/PWM/Timer Modules (SCCP) ..................................................................................................................... 533 11.0 High-Speed Analog Comparator with Slope Compensation DAC ............................................................................................ 551 12.0 Quadrature Encoder Interface (QEI) (Master/Slave) ................................................................................................................ 563 13.0 Universal Asynchronous Receiver Transmitter (UART) ........................................................................................................... 581 14.0 Serial Peripheral Interface (SPI)............................................................................................................................................... 603 15.0 Inter-Integrated Circuit (I2C) ..................................................................................................................................................... 621 16.0 Single-Edge Nibble Transmission (SENT) ............................................................................................................................... 631 17.0 Timer1 ...................................................................................................................................................................................... 641 18.0 Configurable Logic Cell (CLC).................................................................................................................................................. 645 19.0 32-Bit Programmable Cyclic Redundancy Check (CRC) Generator ....................................................................................... 657 20.0 Current Bias Generator (CBG) ................................................................................................................................................. 661 21.0 Special Features ...................................................................................................................................................................... 667 22.0 Instruction Set Summary .......................................................................................................................................................... 713 23.0 Development Support............................................................................................................................................................... 723 24.0 Electrical Characteristics .......................................................................................................................................................... 725 25.0 High-Temperature Electrical Characteristics ............................................................................................................................ 765 26.0 Packaging Information.............................................................................................................................................................. 779 Appendix A: Revision History............................................................................................................................................................. 805 Index ................................................................................................................................................................................................. 807 The Microchip Website....................................................................................................................................................................... 817 Customer Change Notification Service .............................................................................................................................................. 817 Customer Support .............................................................................................................................................................................. 817 Product Identification System............................................................................................................................................................. 819 DS70005319D-page 18  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TO OUR VALUED CUSTOMERS It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and enhanced as new volumes and updates are introduced. If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via E-mail at docerrors@microchip.com. We welcome your feedback. Most Current Data Sheet To obtain the most up-to-date version of this data sheet, please register at our Worldwide Website at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character of the literature number is the version number, (e.g., DS30000000A is version A of document DS30000000). Errata An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of silicon and revision of document to which it applies. To determine if an errata sheet exists for a particular device, please check with one of the following: • Microchip’s Worldwide Website; http://www.microchip.com • Your local Microchip sales office (see last page) When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are using. Customer Notification System Register on our website at www.microchip.com to receive the most current information on all of our products.  2017-2019 Microchip Technology Inc. DS70005319D-page 19 dsPIC33CH128MP508 FAMILY Referenced Sources This device data sheet is based on the following individual chapters of the “dsPIC33/PIC24 Family Reference Manual”. These documents should be considered as the general reference for the operation of a particular module or device feature. Note 1: To access the documents listed below, browse to the documentation section of the dsPIC33CH128MP508 product page of the Microchip website (www.microchip.com) or select a family reference manual section from the following list. In addition to parameters, features and other documentation, the resulting page provides links to the related family reference manual sections. • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • “Introduction” (www.microchip.com/DS70573) “Enhanced CPU” (www.microchip.com/DS70005158) “dsPIC33/PIC24 Program Memory” (www.microchip.com/DS70000613) “Data Memory” (www.microchip.com/DS70595) “Dual Partition Flash Program Memory” (www.microchip.com/DS70005156) “Flash Programming” (www.microchip.com/DS70000609) “Reset” (www.microchip.com/DS70602) “Interrupts” (www.microchip.com/DS70000600) “I/O Ports with Edge Detect” (www.microchip.com/DS70005322) “Deadman Timer” (www.microchip.com/DS70005155) “CAN Flexible Data-Rate (FD) Protocol Module” (www.microchip.com/DS70005340) “12-Bit High-Speed, Multiple SARs A/D Converter (ADC)” (www.microchip.com/DS70005213) “Peripheral Trigger Generator (PTG)” (www.microchip.com/DS70000669) “Programmable Gain Amplifier (PGA)” (www.microchip.com/DS70005146) “Master Slave Interface (MSI) Module” (www.microchip.com/DS70005278) “Watchdog Timer and Power-Saving Modes” (www.microchip.com/DS70615) “Oscillator Module with High-Speed PLL” (www.microchip.com/DS70005255) “Timer1 Module” (www.microchip.com/DS70005279) “Direct Memory Access Controller (DMA)” (www.microchip.com/DS30009742) “Capture/Compare/PWM/Timer (MCCP and SCCP)” (www.microchip.com/DS30003035) “High-Resolution PWM with Fine Edge Placement” (www.microchip.com/DS70005320) “Serial Peripheral Interface (SPI) with Audio Codec Support” (www.microchip.com/DS70005136) “Inter-Integrated Circuit (I2C)” (www.microchip.com/DS70000195) “Multiprotocol Universal Asynchronous Receiver Transmitter (UART) Module” (www.microchip.com/DS70005288) “Single-Edge Nibble Transmission (SENT) Module” (www.microchip.com/DS70005145) “32-Bit Programmable Cyclic Redundancy Check (CRC)” (www.microchip.com/DS30009729) “Configurable Logic Cell (CLC)” (www.microchip.com/DS70005298) “Quadrature Encoder Interface (QEI)” (www.microchip.com/DS70000601) “High-Speed Analog Comparator Module” (www.microchip.com/DS70005280) “Current Bias Generator (CBG)” (www.microchip.com/DS70005253) “Dual Watchdog Timer” (www.microchip.com/DS70005250) “Programming and Diagnostics” (www.microchip.com/DS70608) “CodeGuard™ Security” (www.microchip.com/DS70005182) DS70005319D-page 20  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 1.0 DEVICE OVERVIEW Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive resource. To complement the information in this data sheet, refer to the related section of the “dsPIC33/ PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 3.2 “Master Memory Organization” and Section 4.2 “Slave Memory Organization” in this data sheet for device-specific register and bit information. This document contains device-specific information for the dsPIC33CH128MP508 Digital Signal Controller (DSC) and Microcontroller (MCU) devices. dsPIC33CH128MP508 devices contain extensive Digital Signal Processor (DSP) functionality with a high-performance, 16-bit MCU architecture. Figure 1-2 shows a general block diagram of the cores and peripheral modules of the Master and Slave. Table 1-1 lists the functions of the various pins shown in the pinout diagrams. The Master core and Slave core can operate independently, and can be programmed and debugged separately during the application development. Both processor (Master and Slave) subsystems have their own interrupt controllers, clock generators, ICD, port logic, I/O MUXes and PPS. The device is equivalent to having two complete dsPIC® DSCs on a single die. The Master core will execute the code from Program Flash Memory (PFM) and the Slave core will operate from Program RAM Memory (PRAM).  2017-2019 Microchip Technology Inc. Once the code development is complete, the Master Flash will be programmed with the Master code, as well as the Slave code. After a Power-on Reset (POR), the Slave code from Master Flash will be loaded to the PRAM (program memory of the Slave) and the Slave can execute the code independently of the Master. The Master and Slave can communicate with each other using the Master Slave Interface (MSI) peripheral, and can exchange data between them. Figure 1-1 shows the block diagram of the device operation during a POR and the process of transferring the Slave code from the Master to Slave PRAM. The I/O ports are shared between the Master and Slave. Table 1 shows the number of peripherals and the shared peripherals that the Master and Slave own. There are Configuration bits in the Flash memory that specify the ownership (Master or Slave) of each device pin. The default (erased) state of the Flash assigns all of the device pins to the Master. The two cores (Master and Slave) can both be connected to debug tools, which support independent and simultaneous debugging. When the Slave core or Master core is debugged (non-Dual Debug mode), the S1MCLRx is not used. MCLR is used for programming and debugging both the Master core and the Slave core. S1MCLRx is only used when debugging both the cores at the same time. In normal operation, the “owner” of a device pin is responsible for full control of that pin; this includes both the digital and analog functionality. The pin owner’s GPIO registers control all aspects of the I/O pad, including the ANSELx, CNPUx, CNPDx, ODCx registers and slew rate control. Note: Both the Master and Slave cores can monitor a pin as an input, regardless of pin ownership. Pin ownership is valid only for the output functionality of the port. DS70005319D-page 21 dsPIC33CH128MP508 FAMILY FIGURE 1-1: SLAVE CORE CODE TRANSFER BLOCK DIAGRAM Before a POR: Master Flash Code to Transfer the Slave Code to the Slave PRAM Slave PRAM Master CPU Slave CPU No Code Master Code Slave RAM Master RAM Slave Code After a POR, it is Master code’s responsibility to load the Slave PRAM with the Slave code. Once the Slave code is loaded to PRAM, the Master can enable the Slave to start Slave code execution: Master Flash Code to Transfer the Slave Code to the Slave PRAM Slave PRAM Master CPU Slave CPU Slave Code Master Code Master RAM Slave RAM Slave Code DS70005319D-page 22  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY dsPIC33CH128MP508 FAMILY BLOCK DIAGRAM(1) FIGURE 1-2: CLC (4) QEI (1) SENT (2) CAN FD (1) ADC (1) DMA (6) SCCP (8) I2C (2) WDT/ DMT CRC (1) PTG (1) HS PWM (4) Timer1 (1) DAC/ Comparator (1) SPI/I2S (2) UART (2) OSCI/CLKI Power-up Timer Timing Generation Oscillator Start-up Timer MCLR S1MCLRx POR/BOR PORTA(2) Master CPU MSI (Master Slave Interface) PORTB(2) Slave CPU PORTC(2) Watchdog Timer/ Deadman Timer VDD, VSS AVDD, AVSS PORTD(2) 16 PORTE(2) QEI (1) PGA (3) CLC (4) ADC (3) DMA (2) SCCP (4) I2C (1) Remappable Pins(3) WDT HS PWM (8) Timer1 (1) DAC/ Comparator (3) SPI/I2S (1) UART (1) PORTS Note 1: The numbers in the parentheses are the number of instantiations of the module indicated. 2: Not all I/O pins or features are implemented on all device pinout configurations. See Table 1-1 for specific implementations by pin count. 3: Some peripheral I/Os are only accessible through remappable pins.  2017-2019 Microchip Technology Inc. DS70005319D-page 23 dsPIC33CH128MP508 FAMILY TABLE 1-1: PINOUT I/O DESCRIPTIONS Pin Buffer PPS Type Type Pin Name(1) Description AN0-AN18 S1AN0-S1AN18 S1ANA0, S1ANA1 I I I Analog No Master analog input channels Analog No Slave analog input channels Analog No Slave alternate analog inputs ADCTRG I ST Yes ADC Trigger Input 31 CAN1RX CAN1 I O ST — Yes CAN1 receive input Yes CAN1 transmit output CLKI I CLKO O OSCI I OSCO I/O ST/ No External Clock (EC) source input. Always associated with OSCI pin CMOS function. — No Oscillator crystal output. Connects to crystal or resonator in Crystal Oscillator mode. Optionally functions as CLKO in RC and EC modes. Always associated with OSCO pin function. ST/ No Oscillator crystal input. ST buffer when configured in RC mode; CMOS CMOS otherwise. — No Oscillator crystal output. Connects to crystal or resonator in Crystal Oscillator mode. Optionally functions as CLKO in RC and EC modes. REFOI/S1REFOI I ST Yes Reference clock input REFCLKO/S1REFCLKO(3) O — Yes Reference clock output INT0/S1INT0(3) INT1/S1INT1(3) INT2/S1INT2(3) INT3/S1INT3(3) I I I I ST ST ST ST No Yes Yes Yes External Interrupt 0 External Interrupt 1 External Interrupt 2 External Interrupt 3 IOCA[4:0]/S1IOCA[4:0](3) IOCB[15:0]/S1IOCB[15:0](3) IOCC[15:0]/S1IOCC[15:0](3) IOCD[15:0]/S1IOCD[15:0](3) IOCE[15:0]/S1IOCE[15:0](3) I I I I I ST ST ST ST ST No No No No No Interrupt-on-Change input for PORTA Interrupt-on-Change input for PORTB Interrupt-on-Change input for PORTC Interrupt-on-Change input for PORTD Interrupt-on-Change input for PORTE QEIA1 QEIB1 QEINDX1 QEIHOM1 QEICMP I I I I O ST ST ST ST — Yes Yes Yes Yes Yes QEI Input A QEI Input B QEI Index 1 input QEI Home 1 input QEI comparator output RA0-RA4/S1RA0-S1RA4(3) I/O ST No PORTA is a bidirectional I/O port (3) RB0-RB15/S1RB0-S1RB15 I/O ST No PORTB is a bidirectional I/O port RC0-RC15/S1RC0-S1RC15(3) I/O ST No PORTC is a bidirectional I/O port RD0-RD15/S1RD0-S1RD15(3) I/O ST No PORTD is a bidirectional I/O port RE0-RE15/S1RE0-S1RE15(3) I/O ST No PORTE is a bidirectional I/O port I ST Yes Timer1 external clock input T1CK/S1T1CK(3) Legend: CMOS = CMOS compatible input or output Analog = Analog input P = Power ST = Schmitt Trigger input with CMOS levels O = Output I = Input PPS = Peripheral Pin Select TTL = TTL input buffer Note 1: Not all pins are available in all package variants. See the “Pin Diagrams” section for pin availability. 2: These pins are remappable as well as dedicated. Some of the pins are associated with the Slave function and have S1 attached to the beginning of the name. For example, AN0 for the Slave is S1AN0. 3: S1 attached to the beginning of the name indicates the Slave feature for that function. For example, AN0 for the Slave is S1AN0. 4: Only 48, 64 and 80-pin devices have all eight PWM output pairs on dedicated pins. Refer to pinout diagrams for PWM pin availability on other packages. DS70005319D-page 24  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 1-1: PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name(1) Pin Buffer PPS Type Type Description U1CTS/S1U1CTS(3) U1RTS/S1U1RTS(3) U1RX/S1U1RX(3) U1TX/S1U1TX(3) U1DSR/S1U1DSR U1DTR/S1U1DTR I O I O I O ST — ST — ST — Yes Yes Yes Yes Yes Yes UART1 Clear-to-Send UART1 Request-to-Send UART1 receive UART1 transmit UART1 Data-Set-Ready UART1 Data-Terminal-Ready U2CTS U2RTS U2RX U2TX U2DSR U2DTR I O I O I O ST — ST — ST — Yes Yes Yes Yes Yes Yes UART2 Clear-to-Send UART2 Request-to-Send UART2 receive UART2 transmit UART2 Data-Set-Ready UART2 Data-Terminal-Ready SENT1 SENT2 SENT1OUT SENT2OUT I I O O ST ST — — Yes Yes Yes Yes SENT1 input SENT2 input SENT1 output SENT2 output PTGTRG24 PTGTRG25 O O — — Yes PTG Trigger Output 24 Yes PTG Trigger Output 25 TCKI1-TCKI8/ S1TCKI1-S1TCKI4(3) ICM1-ICM8/ S1ICM1-S1ICM4(3) OCFA-OCFB/ S1OCFA-S1OCFB(3) OCM1-OCM8/ S1OCM1-S1OCM4(3) I ST Yes SCCP Timer Inputs 1 through 8/1 through 4 I ST Yes SCCP Capture Inputs 1 through 8/1 through 4 I ST Yes SCCP Fault Inputs A through B O — Yes SCCP Compare Outputs 1 through 8/1 through 4 SCK1/S1SCK1(3) SDI1/S1SDI1(3) SDO1/S1SDO1(3) SS1/S1SS1(3) I/O I O I/O ST ST — ST Yes Yes Yes Yes Synchronous serial clock input/output for SPI1 SPI1 data in SPI1 data out SPI1 Slave synchronization or frame pulse I/O SCK2 SDI2 SDO2 SS2 I/O I O I/O ST ST — ST Yes Yes Yes Yes Synchronous serial clock input/output for SPI2 SPI2 data in SPI2 data out SPI2 Slave synchronization or frame pulse I/O SCL1/S1SCL1(3) SDA1/S1SDA1(3) ASCL1 ASDA1 I/O I/O I/O I/O ST ST ST ST No No No No Synchronous serial clock input/output for I2C1 Synchronous serial data input/output for I2C1 Alternate synchronous serial clock input/output for I2C1 Alternate synchronous serial data input/output for I2C1 SCL2 SDA2 ASCL2 ASDA2 I/O I/O I/O I/O ST ST ST ST No No No No Synchronous serial clock input/output for I2C2 Synchronous serial data input/output for I2C2 Alternate synchronous serial clock input/output for I2C2 Alternate synchronous serial data input/output for I2C2 Legend: CMOS = CMOS compatible input or output Analog = Analog input P = Power ST = Schmitt Trigger input with CMOS levels O = Output I = Input PPS = Peripheral Pin Select TTL = TTL input buffer Note 1: Not all pins are available in all package variants. See the “Pin Diagrams” section for pin availability. 2: These pins are remappable as well as dedicated. Some of the pins are associated with the Slave function and have S1 attached to the beginning of the name. For example, AN0 for the Slave is S1AN0. 3: S1 attached to the beginning of the name indicates the Slave feature for that function. For example, AN0 for the Slave is S1AN0. 4: Only 48, 64 and 80-pin devices have all eight PWM output pairs on dedicated pins. Refer to pinout diagrams for PWM pin availability on other packages.  2017-2019 Microchip Technology Inc. DS70005319D-page 25 dsPIC33CH128MP508 FAMILY TABLE 1-1: PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name(1) Pin Buffer PPS Type Type Description TMS TCK TDI TDO I I I O ST ST ST — No No No No PCI8-PCI18/ S1PCI8-S1PCI18 PWMEA-PWMED/ S1PWMEA-S1PWMED PCI19-PCI22/ S1PCI19-S1PCI22(3) PWM1L-PWM4L/S1PWM1L/ S1PWM8L(3,4) PWM1H-PWM4H/ S1PWM1H-S1PWM8H(2,3,4) I ST Yes PWM Inputs 8 through 18 O — Yes PWM Event Outputs A through D I ST No PWM Inputs 19 through 22 O — No PWM Low Outputs 1 through 8 O — PWM High Outputs 1 through 8 I ST Yes CLC Inputs A through D O — Yes CLC Outputs 1 through 4 CLCINA-CLCIND/ S1CLCINA-S1CLCIND(3) CLC1OUT-CLC4OUT JTAG Test mode select pin JTAG test clock input pin JTAG test data input pin JTAG test data output pin CMP1 CMP1A/ S1CMP1A-S1CMP3A(3) CMP1B/ S1CMP1B-S1CMP3B(3) CMP1D/ S1CMP1D-S1CMP3D(3) O I — Yes Comparator 1 output Analog No Comparator Channels 1A through 3A inputs I Analog No Comparator Channels 1B through 3B inputs I Analog No Comparator Channels 1D through 3D inputs DACOUT1 O IBIAS3, IBIAS2, IBIAS1, IBIAS0/ISRC3, ISRC2, ISRC1, ISRC0 O — No DAC output voltage Analog No Constant-Current Outputs 0 through 3 S1PGA1P2 I Analog No PGA1 Positive Input 2 S1PGA1N2 I Analog No PGA1 Negative Input 2 S1PGA2P2 I Analog No PGA2 Positive Input 2 S1PGA2N2 I Analog No PGA2 Negative Input 2 S1PGA3P1-S1PGA3P2 I Analog No PGA3 Positive Inputs 1 through 2 S1PGA3N2 I Analog No PGA3 Negative Input 2 Legend: CMOS = CMOS compatible input or output Analog = Analog input P = Power ST = Schmitt Trigger input with CMOS levels O = Output I = Input PPS = Peripheral Pin Select TTL = TTL input buffer Note 1: Not all pins are available in all package variants. See the “Pin Diagrams” section for pin availability. 2: These pins are remappable as well as dedicated. Some of the pins are associated with the Slave function and have S1 attached to the beginning of the name. For example, AN0 for the Slave is S1AN0. 3: S1 attached to the beginning of the name indicates the Slave feature for that function. For example, AN0 for the Slave is S1AN0. 4: Only 48, 64 and 80-pin devices have all eight PWM output pairs on dedicated pins. Refer to pinout diagrams for PWM pin availability on other packages. DS70005319D-page 26  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 1-1: PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name(1) Pin Buffer PPS Type Type Description PGD1/S1PGD1(3) PGC1/S1PGC1(3) I/O I ST ST PGD2/S1PGD2(3) PGC2/S1PGC2(3) I/O I ST ST PGD3/S1PGD3(3) PGC3/S1PGC3(3) I/O I ST ST MCLR/S1MCLR1/S1MCLR2/ S1MCLR3 I/P ST No Master Clear (Reset) input. This pin is an active-low Reset to the device. S1MCLRx is valid only for Slave debug in Dual Debug mode. AVDD P P No Positive supply for analog modules. This pin must be connected at all times. AVSS P P No Ground reference for analog modules. This pin must be connected at all times. VDD P — No Positive supply for peripheral logic and I/O pins VSS P — No Ground reference for logic and I/O pins No Data I/O pin for Programming/Debugging Communication Channel 1 No Clock input pin for Programming/Debugging Communication Channel 1 No Data I/O pin for Programming/Debugging Communication Channel 2 No Clock input pin for Programming/Debugging Communication Channel 2 No Data I/O pin for Programming/Debugging Communication Channel 3 No Clock input pin for Programming/Debugging Communication Channel 3 Legend: CMOS = CMOS compatible input or output Analog = Analog input P = Power ST = Schmitt Trigger input with CMOS levels O = Output I = Input PPS = Peripheral Pin Select TTL = TTL input buffer Note 1: Not all pins are available in all package variants. See the “Pin Diagrams” section for pin availability. 2: These pins are remappable as well as dedicated. Some of the pins are associated with the Slave function and have S1 attached to the beginning of the name. For example, AN0 for the Slave is S1AN0. 3: S1 attached to the beginning of the name indicates the Slave feature for that function. For example, AN0 for the Slave is S1AN0. 4: Only 48, 64 and 80-pin devices have all eight PWM output pairs on dedicated pins. Refer to pinout diagrams for PWM pin availability on other packages.  2017-2019 Microchip Technology Inc. DS70005319D-page 27 dsPIC33CH128MP508 FAMILY NOTES: DS70005319D-page 28  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 2.0 2.1 GUIDELINES FOR GETTING STARTED WITH 16-BIT DIGITAL SIGNAL CONTROLLERS 2.2 Basic Connection Requirements Consider the following criteria when using decoupling capacitors: Getting started with the family devices of the dsPIC33CH128MP508 requires attention to a minimal set of device pin connections before proceeding with development. The following is a list of pin names which must always be connected: • All VDD and VSS pins (see Section 2.2 “Decoupling Capacitors”) • All AVDD and AVSS pins regardless if ADC module is not used (see Section 2.2 “Decoupling Capacitors”) • MCLR pin (see Section 2.3 “Master Clear (MCLR) Pin”) • PGCx/PGDx pins used for In-Circuit Serial Programming™ (ICSP™) and debugging purposes (see Section 2.4 “ICSP Pins”) • OSCI and OSCO pins when an external oscillator source is used (see Section 2.5 “External Oscillator Pins”)  2017-2019 Microchip Technology Inc. Decoupling Capacitors The use of decoupling capacitors on every pair of power supply pins, such as VDD, VSS, AVDD and AVSS is required. • Value and type of capacitor: Recommendation of 0.1 µF (100 nF), 10-20V. This capacitor should be a low-ESR and have resonance frequency in the range of 20 MHz and higher. It is recommended to use ceramic capacitors. • Placement on the printed circuit board: The decoupling capacitors should be placed as close to the pins as possible. It is recommended to place the capacitors on the same side of the board as the device. If space is constricted, the capacitor can be placed on another layer on the PCB using a via; however, ensure that the trace length from the pin to the capacitor is within one-quarter inch (6 mm) in length. • Handling high-frequency noise: If the board is experiencing high-frequency noise, above tens of MHz, add a second ceramic-type capacitor in parallel to the above described decoupling capacitor. The value of the second capacitor can be in the range of 0.01 µF to 0.001 µF. Place this second capacitor next to the primary decoupling capacitor. In high-speed circuit designs, consider implementing a decade pair of capacitances as close to the power and ground pins as possible. For example, 0.1 µF in parallel with 0.001 µF. • Maximizing performance: On the board layout from the power supply circuit, run the power and return traces to the decoupling capacitors first, and then to the device pins. This ensures that the decoupling capacitors are first in the power chain. Equally important is to keep the trace length between the capacitor and the power pins to a minimum, thereby reducing PCB track inductance. DS70005319D-page 29 dsPIC33CH128MP508 FAMILY FIGURE 2-1: RECOMMENDED MINIMUM CONNECTION 0.1 µF Ceramic R R1 VSS VDD VDD C dsPIC33 VDD 0.1 µF Ceramic VSS VSS AVSS VDD AVDD 0.1 µF Ceramic VDD 0.1 µF Ceramic 0.1 µF Ceramic As an option, instead of a hard-wired connection, an inductor (L1) can be substituted between VDD and AVDD to improve ADC noise rejection. The inductor impedance should be less than 1 and the inductor capacity greater than 10 mA. Where: F CNV f = -------------2 1 f = ---------------------- 2 LC  (i.e., ADC Conversion Rate/2) 2 1 L =  ----------------------   2f C  2.2.1 The MCLR functions: provides two specific device • Device Reset • Device Programming and Debugging. For example, as shown in Figure 2-2, it is recommended that the capacitor, C, be isolated from the MCLR pin during programming and debugging operations. Note 1: There are the S1MCLR1, S1MCLR2 and S1MCLR3 pins and they are used for Slave debug during the dual debug process. Those pins do not reset the Slave core during normal operation. FIGURE 2-2: On boards with power traces running longer than six inches in length, it is suggested to use a bulk capacitor for integrated circuits, including DSCs, to supply a local power source. The value of the bulk capacitor should be determined based on the trace resistance that connects the power supply source to the device and the maximum current drawn by the device in the application. In other words, select the bulk capacitor so that it meets the acceptable voltage sag at the device. Typical values range from 4.7 µF to 47 µF. EXAMPLE OF MCLR PIN CONNECTIONS VDD R(1) BULK CAPACITORS DS70005319D-page 30 pin Place the components, as shown in Figure 2-2, within one-quarter inch (6 mm) from the MCLR pin. L1(1) Note 1: Master Clear (MCLR) Pin During device programming and debugging, the resistance and capacitance that can be added to the pin must be considered. Device programmers and debuggers drive the MCLR pin. Consequently, specific voltage levels (VIH and VIL) and fast signal transitions must not be adversely affected. Therefore, specific values of R and C will need to be adjusted based on the application and PCB requirements. MCLR VSS 2.3 R1(2) MCLR JP dsPIC33 C Note 1: R  10 k is recommended. A suggested starting value is 10 k. Ensure that the MCLR pin VIH and VIL specifications are met. 2: R1  470 will limit any current flowing into MCLR from the external capacitor, C, in the event of MCLR pin breakdown due to Electrostatic Discharge (ESD) or Electrical Overstress (EOS). Ensure that the MCLR pin VIH and VIL specifications are met.  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 2.4 ICSP Pins The PGCx and PGDx pins are used for ICSP and debugging purposes. It is recommended to keep the trace length between the ICSP connector and the ICSP pins on the device as short as possible. If the ICSP connector is expected to experience an ESD event, a series resistor is recommended, with the value in the range of a few tens of Ohms, not to exceed 100 Ohms. Pull-up resistors, series diodes and capacitors on the PGCx and PGDx pins are not recommended as they will interfere with the programmer/debugger communications to the device. If such discrete components are an application requirement, they should be removed from the circuit during programming and debugging. Alternatively, refer to the AC/DC characteristics and timing requirements information in the respective device Flash programming specification for information on capacitive loading limits and pin Voltage Input High (VIH) and Voltage Input Low (VIL) requirements. Ensure that the “Communication Channel Select” (i.e., PGCx/PGDx pins) programmed into the device matches the physical connections for the ICSP to PICkit™ 3, MPLAB® ICD 3 or MPLAB REAL ICE™ emulator. For more information on MPLAB ICD 2, MPLAB ICD 3 and REAL ICE emulator connection requirements, refer to the following documents that are available on the Microchip website. • “Using MPLAB® ICD 3 In-Circuit Debugger” (poster) (DS51765) • “Development Tools Design Advisory” (DS51764) • “MPLAB® REAL ICE™ In-Circuit Emulator User’s Guide” (DS51616) • “Using MPLAB® REAL ICE™ In-Circuit Emulator” (poster) (DS51749)  2017-2019 Microchip Technology Inc. 2.5 External Oscillator Pins Many DSCs have options for at least two oscillators: a high-frequency Primary Oscillator (POSC) and a low-frequency Secondary Oscillator (SOSC). For details, see Section 6.12.1 “Master Oscillator Control Registers”. The oscillator circuit should be placed on the same side of the board as the device. Also, place the oscillator circuit close to the respective oscillator pins, not exceeding one-half inch (12 mm) distance between them. The load capacitors should be placed next to the oscillator itself, on the same side of the board. Use a grounded copper pour around the oscillator circuit to isolate them from surrounding circuits. The grounded copper pour should be routed directly to the MCU ground. Do not run any signal traces or power traces inside the ground pour. Also, if using a two-sided board, avoid any traces on the other side of the board where the crystal is placed. A suggested layout is shown in Figure 2-3. FIGURE 2-3: SUGGESTED PLACEMENT OF THE OSCILLATOR CIRCUIT Main Oscillator Guard Ring Guard Trace Oscillator Pins DS70005319D-page 31 dsPIC33CH128MP508 FAMILY 2.6 Oscillator Value Conditions on Device Start-up 2.8 If the PLL of the target device is enabled and configured for the device start-up oscillator, the maximum oscillator source frequency must be limited to a certain frequency (see Section 6.0 “Oscillator with High-Frequency PLL”) to comply with device PLL start-up conditions. This means that if the external oscillator frequency is outside this range, the application must start up in the FRC mode first. The default PLL settings after a POR with an oscillator frequency outside this range will violate the device operating speed. Once the device powers up, the application firmware can initialize the PLL SFRs, CLKDIV and PLLFBD, to a suitable value, and then perform a clock switch to the Oscillator + PLL clock source. Note that clock switching must be enabled in the device Configuration Word. 2.7 Unused I/Os Unused I/O pins should be configured as outputs and driven to a logic low state. Targeted Applications • Power Factor Correction (PFC): - Interleaved PFC - Critical Conduction PFC - Bridgeless PFC • DC/DC Converters: - Buck, Boost, Forward, Flyback, Push-Pull - Half/Full-Bridge - Phase-Shift Full-Bridge - Resonant Converters • DC/AC: - Half/Full-Bridge Inverter - Resonant Inverter • Motor Control - BLDC - PMSM - SR - ACIM Examples of typical application connections are shown in Figure 2-4 through Figure 2-6. Alternatively, connect a 1k to 10k resistor between VSS and unused pins, and drive the output to logic low. FIGURE 2-4: INTERLEAVED PFC VOUT+ |VAC| k1 k4 k2 VAC k3 VOUT- PGA/ADC Channel ADC Channel DS70005319D-page 32 FET Driver FET Driver PWM PGA/ADC Channel PWM PGA/ADC Channel ADC Channel dsPIC33CH128MP508  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 2-5: PHASE-SHIFTED FULL-BRIDGE CONVERTER VIN+ Gate 6 Gate 3 Gate 1 VOUT+ S1 S3 VOUT- Gate 2 Gate 4 Gate 5 Gate 6 Gate 5 VIN- FET Driver k2 PWM ADC Channel k1 Analog Ground Gate 1 S1 FET Driver PWM Gate 3 S3 FET Driver PGA/ADC Channel dsPIC33CH128MP508 PWM Gate 2 Gate 4  2017-2019 Microchip Technology Inc. DS70005319D-page 33 dsPIC33CH128MP508 FAMILY FIGURE 2-6: OFF-LINE UPS VDC Push-Pull Converter Full-Bridge Inverter VOUT+ VBAT + VOUTGND GND FET Driver FET Driver PWM PWM PGA/ADC ADC or Analog Comp. k3 k2 k1 FET Driver FET Driver FET Driver FET Driver PWM PWM PWM PWM dsPIC33CH128MP508 ADC k4 k5 ADC ADC ADC PWM FET Driver k6 + Battery Charger DS70005319D-page 34  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.0 MASTER MODULES 3.1 Master CPU Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “Enhanced CPU” (www.microchip.com/DS70005158) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). There are two independent CPU cores in the dsPIC33CH128MP508 family. The Master and Slave cores are similar, except for the fact that the Slave core can run at a higher speed than the Master core. The Slave core fetches instructions from the PRAM and the Master core fetches the code from the Flash. The Master and Slave cores can run independently asynchronously, at the same speed or at a different speed. This section discusses the Master core. Note: All of the associated register names are the same on the Master, as well as on the Slave. The Slave code will be developed in a separate project in MPLAB® X IDE with the device selection, dsPIC33CH128MP508S1, where the S1 indicates the Slave device. 3.1.1 REGISTERS The dsPIC33CH128MP508 devices have sixteen, 16-bit Working registers in the programmer’s model. Each of the Working registers can act as a Data, Address or Address Offset register. The 16th Working register (W15) operates as a Software Stack Pointer for interrupts and calls. In addition, the dsPIC33CH128MP508 devices include four Alternate Working register sets, which consist of W0 through W14. The Alternate Working registers can be made persistent to help reduce the saving and restoring of register content during Interrupt Service Routines (ISRs). The Alternate Working registers can be assigned to a specific Interrupt Priority Level (IPL1 through IPL7) by configuring the CTXTx[2:0] bits in the FALTREG Configuration register. The Alternate Working registers can also be accessed manually by using the CTXTSWP instruction. The CCTXI[2:0] and MCTXI[2:0] bits in the CTXTSTAT register can be used to identify the current, and most recent, manually selected Working register sets. 3.1.2 INSTRUCTION SET The instruction set for dsPIC33CH128MP508 devices has two classes of instructions: the MCU class of instructions and the DSP class of instructions. These two instruction classes are seamlessly integrated into the architecture and execute from a single execution unit. The instruction set includes many addressing modes and was designed for optimum C compiler efficiency. The dsPIC33CH128MP508 family CPU has a 16-bit (data) modified Harvard architecture with an enhanced instruction set, including significant support for Digital Signal Processing (DSP). The CPU has a 24-bit instruction word with a variable length opcode field. The Program Counter (PC) is 23 bits wide and addresses up to 4M x 24 bits of user program memory space. An instruction prefetch mechanism helps maintain throughput and provides predictable execution. Most instructions execute in a single-cycle effective execution rate, with the exception of instructions that change the program flow, the double-word move (MOV.D) instruction, PSV accesses and the table instructions. Overhead-free program loop constructs are supported using the DO and REPEAT instructions, both of which are interruptible at any point.  2017-2019 Microchip Technology Inc. DS70005319D-page 35 dsPIC33CH128MP508 FAMILY 3.1.3 DATA SPACE ADDRESSING The base Data Space (DS) can be addressed as up to 4K words or 8 Kbytes, and is split into two blocks, referred to as X and Y data memory. Each memory block has its own independent Address Generation Unit (AGU). The MCU class of instructions operates solely through the X memory AGU, which accesses the entire memory map as one linear Data Space. Certain DSP instructions operate through the X and Y AGUs to support dual operand reads, which splits the data address space into two parts. The X and Y Data Space boundary is device-specific. The upper 32 Kbytes of the Data Space memory map can optionally be mapped into Program Space (PS) at any 16K program word boundary. The program-to-Data Space mapping feature, known as Program Space Visibility (PSV), lets any instruction access Program Space as if it were Data Space. Refer to “Data Memory” (www.microchip.com/DS70595) in the “dsPIC33/PIC24 Family Reference Manual” for more details on PSV and table accesses. 3.1.4 ADDRESSING MODES The CPU supports these addressing modes: • • • • • • Inherent (no operand) Relative Literal Memory Direct Register Direct Register Indirect Each instruction is associated with a predefined addressing mode group, depending upon its functional requirements. As many as six addressing modes are supported for each instruction. On dsPIC33CH128MP508 family devices, overheadfree circular buffers (Modulo Addressing) are supported in both X and Y address spaces. The Modulo Addressing removes the software boundary checking overhead for DSP algorithms. The X AGU Circular Addressing can be used with any of the MCU class of instructions. The X AGU also supports BitReversed Addressing to greatly simplify input or output data re-ordering for radix-2 FFT algorithms. DS70005319D-page 36  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 3-1: dsPIC33CH128MP508 FAMILY (MASTER) CPU BLOCK DIAGRAM X Address Bus Y Data Bus X Data Bus Interrupt Controller PSV and Table Data Access 24 Control Block 8 Data Latch Data Latch Y Data RAM X Data RAM Address Latch Address Latch 16 Y Address Bus 24 24 PCU PCH PCL Program Counter Loop Stack Control Control Logic Logic Address Latch 16 16 16 16 16 16 24 16 X RAGU X WAGU 16 Y AGU Program Memory EA MUX 16 Data Latch Literal Data 24 24 16 IR ROM Latch 16 16 16-Bit Working Register Arrays 16 16 16 Divide Support DSP Engine 16-Bit ALU Control Signals to Various Blocks Instruction Decode and Control 16 Power, Reset and Oscillator Modules 16 Ports Peripheral Modules Slave CPU  2017-2019 Microchip Technology Inc. MSI DS70005319D-page 37 dsPIC33CH128MP508 FAMILY 3.1.5 PROGRAMMER’S MODEL The programmer’s model for the dsPIC33CH128MP508 family is shown in Figure 3-2. All registers in the programmer’s model are memory-mapped and can be manipulated directly by instructions. Table 3-1 lists a description of each register. TABLE 3-1: In addition to the registers contained in the programmer’s model, the dsPIC33CH128MP508 devices contain control registers for Modulo Addressing, Bit-Reversed Addressing and interrupts. These registers are described in subsequent sections of this document. All registers associated with the programmer’s model are memory-mapped, as shown in Figure 3-3 and Figure 3-4. PROGRAMMER’S MODEL REGISTER DESCRIPTIONS Register(s) Name W0 through W15 (1) Description Working Register Array W14(1) Alternate Working Register Array 1 W0 through W14(1) Alternate Working Register Array 2 (1) Alternate Working Register Array 3 W0 through W14(1) Alternate Working Register Array 4 W0 through W0 through W14 ACCA, ACCB 40-Bit DSP Accumulators (Additional 4 Alternate Accumulators) PC 23-Bit Program Counter SR ALU and DSP Engine STATUS Register SPLIM Stack Pointer Limit Value Register TBLPAG Table Memory Page Address Register DSRPAG Extended Data Space (EDS) Read Page Register RCOUNT REPEAT Loop Counter Register DCOUNT DO Loop Counter Register DOSTARTH, DOSTARTL (2) DO Loop Start Address Register (High and Low) DOENDH, DOENDL DO Loop End Address Register (High and Low) CORCON Contains DSP Engine, DO Loop Control and Trap Status bits Note 1: 2: Memory-mapped W0 through W14 represent the value of the register in the currently active CPU context. The DOSTARTH and DOSTARTL registers are read-only. DS70005319D-page 38  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 3-2: PROGRAMMER’S MODEL (MASTER) D15 D0 D15 D0 D15 D0 D15 D0 D15 D0 W0 (WREG) W1 W0-W3 W0 W1 W0 W0 W0 W1 W1 W1 W4 W2 W3 W4 W2 W2 W2 W3 W3 W3 W4 W4 W4 W5 W5 W5 W5 W5 W6 W7 W6 W7 W6 W7 W6 W6 W7 W7 W8 W8 W8 W8 W8 W9 W9 W9 W9 W9 W2 W3 DSP Operand Registers Working/Address Registers DSP Address Registers W10 W10 W11 W11 W12 W12 W13 W13 W10 W10 W10 W11 W11 W11 Frame Pointer/W14 W14 W14 W14 W14 Alternate Working/Address Registers W12 W12 W12 W13 W13 W13 Stack Pointer/W15 0 PUSH.S and POP.S Shadows SPLIM Nested DO Stack AD39 AD15 AD31 AD39 AD15 AD31 AD39 AD0 AD0 AD0 AD15 AD31 AD39 DSP Accumulators(1) Stack Pointer Limit 0 AD31 AD39 AD15 AD31 AD0 AD0 AD15 ACCA ACCB PC23 PC0 0 0 Program Counter 0 7 TBLPAG Data Table Page Address 9 0 DSRPAG X Data Space Read Page Address 15 0 REPEAT Loop Counter RCOUNT 15 0 DCOUNT DO Loop Counter and Stack 23 0 DOSTART 0 0 DO Loop Start Address and Stack 23 0 DOEND 0 0 DO Loop End Address and Stack 15 0 CORCON CPU Core Control Register SRL OA OB SA SB OAB SAB  2017-2019 Microchip Technology Inc. DA DC IPL2 IPL1 IPL0 RA N OV Z C STATUS Register DS70005319D-page 39 dsPIC33CH128MP508 FAMILY 3.1.6 CPU RESOURCES Many useful resources are provided on the main product page of the Microchip website for the devices listed in this data sheet. This product page contains the latest updates and additional information. DS70005319D-page 40 3.1.6.1 Key Resources • “Enhanced CPU” (www.microchip.com/ DS70005158) in the “dsPIC33/PIC24 Family Reference Manual” • Code Samples • Application Notes • Software Libraries • Webinars • All related “dsPIC33/PIC24 Family Reference Manual” Sections • Development Tools  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.1.7 CPU CONTROL/STATUS REGISTERS REGISTER 3-1: SR: CPU STATUS REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/C-0 R/C-0 R-0 R/W-0 OA OB SA(3) SB(3) OAB SAB DA DC bit 15 bit 8 R/W-0(2) R/W-0(2) IPL2(1) IPL1 (1) R/W-0(2) IPL0 (1) R-0 R/W-0 R/W-0 R/W-0 R/W-0 RA N OV Z C bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’= Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 OA: Accumulator A Overflow Status bit 1 = Accumulator A has overflowed 0 = Accumulator A has not overflowed bit 14 OB: Accumulator B Overflow Status bit 1 = Accumulator B has overflowed 0 = Accumulator B has not overflowed bit 13 SA: Accumulator A Saturation ‘Sticky’ Status bit(3) 1 = Accumulator A is saturated or has been saturated at some time 0 = Accumulator A is not saturated bit 12 SB: Accumulator B Saturation ‘Sticky’ Status bit(3) 1 = Accumulator B is saturated or has been saturated at some time 0 = Accumulator B is not saturated bit 11 OAB: OA || OB Combined Accumulator Overflow Status bit 1 = Accumulator A or B has overflowed 0 = Neither Accumulator A or B has overflowed bit 10 SAB: SA || SB Combined Accumulator ‘Sticky’ Status bit 1 = Accumulator A or B is saturated or has been saturated at some time 0 = Neither Accumulator A or B is saturated bit 9 DA: DO Loop Active bit 1 = DO loop is in progress 0 = DO loop is not in progress bit 8 DC: MCU ALU Half Carry/Borrow bit 1 = A carry-out from the 4th low-order bit (for byte-sized data) or 8th low-order bit (for word-sized data) of the result occurred 0 = No carry-out from the 4th low-order bit (for byte-sized data) or 8th low-order bit (for word-sized data) of the result occurred Note 1: 2: 3: The IPL[2:0] bits are concatenated with the IPL[3] bit (CORCON[3]) to form the CPU Interrupt Priority Level. The value in parentheses indicates the IPL, if IPL[3] = 1. User interrupts are disabled when IPL[3] = 1. The IPL[2:0] Status bits are read-only when the NSTDIS bit (INTCON1[15]) = 1. A data write to the SR register can modify the SA and SB bits by either a data write to SA and SB or by clearing the SAB bit. To avoid a possible SA or SB bit write race condition, the SA and SB bits should not be modified using bit operations.  2017-2019 Microchip Technology Inc. DS70005319D-page 41 dsPIC33CH128MP508 FAMILY REGISTER 3-1: SR: CPU STATUS REGISTER (CONTINUED) bit 7-5 IPL[2:0]: CPU Interrupt Priority Level Status bits(1,2) 111 = CPU Interrupt Priority Level is 7 (15); user interrupts are disabled 110 = CPU Interrupt Priority Level is 6 (14) 101 = CPU Interrupt Priority Level is 5 (13) 100 = CPU Interrupt Priority Level is 4 (12) 011 = CPU Interrupt Priority Level is 3 (11) 010 = CPU Interrupt Priority Level is 2 (10) 001 = CPU Interrupt Priority Level is 1 (9) 000 = CPU Interrupt Priority Level is 0 (8) bit 4 RA: REPEAT Loop Active bit 1 = REPEAT loop is in progress 0 = REPEAT loop is not in progress bit 3 N: MCU ALU Negative bit 1 = Result was negative 0 = Result was non-negative (zero or positive) bit 2 OV: MCU ALU Overflow bit This bit is used for signed arithmetic (two’s complement). It indicates an overflow of the magnitude that causes the sign bit to change state. 1 = Overflow occurred for signed arithmetic (in this arithmetic operation) 0 = No overflow occurred bit 1 Z: MCU ALU Zero bit 1 = An operation that affects the Z bit has set it at some time in the past 0 = The most recent operation that affects the Z bit has cleared it (i.e., a non-zero result) bit 0 C: MCU ALU Carry/Borrow bit 1 = A carry-out from the Most Significant bit of the result occurred 0 = No carry-out from the Most Significant bit of the result occurred Note 1: 2: 3: The IPL[2:0] bits are concatenated with the IPL[3] bit (CORCON[3]) to form the CPU Interrupt Priority Level. The value in parentheses indicates the IPL, if IPL[3] = 1. User interrupts are disabled when IPL[3] = 1. The IPL[2:0] Status bits are read-only when the NSTDIS bit (INTCON1[15]) = 1. A data write to the SR register can modify the SA and SB bits by either a data write to SA and SB or by clearing the SAB bit. To avoid a possible SA or SB bit write race condition, the SA and SB bits should not be modified using bit operations. DS70005319D-page 42  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-2: CORCON: CORE CONTROL REGISTER R/W-0 U-0 R/W-0 R/W-0 R/W-0 R-0 R-0 R-0 VAR — US1 US0 EDT(1) DL2 DL1 DL0 bit 15 bit 8 R/W-0 R/W-0 R/W-1 R/W-0 R/C-0 R-0 R/W-0 R/W-0 SATA SATB SATDW ACCSAT IPL3(2) SFA RND IF bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 VAR: Variable Exception Processing Latency Control bit 1 = Variable exception processing is enabled 0 = Fixed exception processing is enabled bit 14 Unimplemented: Read as ‘0’ bit 13-12 US[1:0]: DSP Multiply Unsigned/Signed Control bits 11 = Reserved 10 = DSP engine multiplies are mixed sign 01 = DSP engine multiplies are unsigned 00 = DSP engine multiplies are signed bit 11 EDT: Early DO Loop Termination Control bit(1) 1 = Terminates executing DO loop at the end of the current loop iteration 0 = No effect bit 10-8 DL[2:0]: DO Loop Nesting Level Status bits 111 = Seven DO loops are active ... 001 = One DO loop is active 000 = Zero DO loops are active bit 7 SATA: ACCA Saturation Enable bit 1 = Accumulator A saturation is enabled 0 = Accumulator A saturation is disabled bit 6 SATB: ACCB Saturation Enable bit 1 = Accumulator B saturation is enabled 0 = Accumulator B saturation is disabled bit 5 SATDW: Data Space Write from DSP Engine Saturation Enable bit 1 = Data Space write saturation is enabled 0 = Data Space write saturation is disabled bit 4 ACCSAT: Accumulator Saturation Mode Select bit 1 = 9.31 saturation (super saturation) 0 = 1.31 saturation (normal saturation) bit 3 IPL3: CPU Interrupt Priority Level Status bit 3(2) 1 = CPU Interrupt Priority Level is greater than 7 0 = CPU Interrupt Priority Level is 7 or less Note 1: 2: x = Bit is unknown This bit is always read as ‘0’. The IPL3 bit is concatenated with the IPL[2:0] bits (SR[7:5]) to form the CPU Interrupt Priority Level.  2017-2019 Microchip Technology Inc. DS70005319D-page 43 dsPIC33CH128MP508 FAMILY REGISTER 3-2: CORCON: CORE CONTROL REGISTER (CONTINUED) bit 2 SFA: Stack Frame Active Status bit 1 = Stack frame is active; W14 and W15 address 0x0000 to 0xFFFF, regardless of DSRPAG 0 = Stack frame is not active; W14 and W15 address the base Data Space bit 1 RND: Rounding Mode Select bit 1 = Biased (conventional) rounding is enabled 0 = Unbiased (convergent) rounding is enabled bit 0 IF: Integer or Fractional Multiplier Mode Select bit 1 = Integer mode is enabled for DSP multiply 0 = Fractional mode is enabled for DSP multiply Note 1: 2: This bit is always read as ‘0’. The IPL3 bit is concatenated with the IPL[2:0] bits (SR[7:5]) to form the CPU Interrupt Priority Level. REGISTER 3-3: CTXTSTAT: CPU W REGISTER CONTEXT STATUS REGISTER U-0 U-0 U-0 U-0 U-0 — — — — — R-0 R-0 R-0 CCTXI[2:0] bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 — — — — — R-0 R-0 R-0 MCTXI[2:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-11 Unimplemented: Read as ‘0’ bit 10-8 CCTXI[2:0]: Current (W Register) Context Identifier bits 111 = Reserved • • • 100 = Alternate Working Register Set 4 is currently in use 011 = Alternate Working Register Set 3 is currently in use 010 = Alternate Working Register Set 2 is currently in use 001 = Alternate Working Register Set 1 is currently in use 000 = Default register set is currently in use bit 7-3 Unimplemented: Read as ‘0’ bit 2-0 MCTXI[2:0]: Manual (W Register) Context Identifier bits 111 = Reserved • • • 100 = Alternate Working Register Set 4 was most recently manually selected 011 = Alternate Working Register Set 3 was most recently manually selected 010 = Alternate Working Register Set 2 was most recently manually selected 001 = Alternate Working Register Set 1 was most recently manually selected 000 = Default register set was most recently manually selected DS70005319D-page 44  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.1.8 ARITHMETIC LOGIC UNIT (ALU) The dsPIC33CH128MP508 family ALU is 16 bits wide and is capable of addition, subtraction, bit shifts and logic operations. Unless otherwise mentioned, arithmetic operations are two’s complement in nature. Depending on the operation, the ALU can affect the values of the Carry (C), Zero (Z), Negative (N), Overflow (OV) and Digit Carry (DC) Status bits in the SR register. The C and DC Status bits operate as Borrow and Digit Borrow bits, respectively, for subtraction operations. The ALU can perform 8-bit or 16-bit operations, depending on the mode of the instruction that is used. Data for the ALU operation can come from the W register array or data memory, depending on the addressing mode of the instruction. Likewise, output data from the ALU can be written to the W register array or a data memory location. Refer to the “16-Bit MCU and DSC Programmer’s Reference Manual” (DS70000157) for information on the SR bits affected by each instruction. The core CPU incorporates hardware support for both multiplication and division. This includes a dedicated hardware multiplier and support hardware for 16-bit divisor division. 3.1.8.1 Multiplier Using the high-speed, 17-bit x 17-bit multiplier, the ALU supports unsigned, signed or mixed-sign operation in several MCU multiplication modes: • • • • • • • 16-bit x 16-bit signed 16-bit x 16-bit unsigned 16-bit signed x 5-bit (literal) unsigned 16-bit signed x 16-bit unsigned 16-bit unsigned x 5-bit (literal) unsigned 16-bit unsigned x 16-bit signed 8-bit unsigned x 8-bit unsigned 3.1.8.2 Divider The divide block supports 32-bit/16-bit and 16-bit/16-bit signed and unsigned integer divide operations with the following data sizes: • • • • 3.1.9 DSP ENGINE The DSP engine consists of a high-speed 17-bit x 17-bit multiplier, a 40-bit barrel shifter and a 40-bit adder/ subtracter (with two target accumulators, round and saturation logic). The DSP engine can also perform inherent accumulatorto-accumulator operations that require no additional data. These instructions are, ADD, SUB, NEG, MIN and MAX. The DSP engine has options selected through bits in the CPU Core Control register (CORCON), as listed below: • Fractional or integer DSP multiply (IF) • Signed, unsigned or mixed-sign DSP multiply (USx) • Conventional or convergent rounding (RND) • Automatic saturation on/off for ACCA (SATA) • Automatic saturation on/off for ACCB (SATB) • Automatic saturation on/off for writes to data memory (SATDW) • Accumulator Saturation mode selection (ACCSAT) TABLE 3-2: Instruction CLR DSP INSTRUCTIONS SUMMARY Algebraic Operation ACC Write-Back Yes A=0 2 ED A = (x – y) No EDAC A = A + (x – y)2 No MAC A = A + (x • y) Yes MAC A = A + x2 No MOVSAC No change in A Yes MPY A=x•y No 2 No MPY A=x MPY.N A=–x•y No MSC A=A–x•y Yes 32-bit signed/16-bit signed divide 32-bit unsigned/16-bit unsigned divide 16-bit signed/16-bit signed divide 16-bit unsigned/16-bit unsigned divide The 16-bit signed and unsigned DIV instructions can specify any W register for both the 16-bit divisor (Wn) and any W register (aligned) pair (W(m + 1):Wm) for the 32-bit dividend. The divide algorithm takes one cycle per bit of divisor, so both 32-bit/16-bit and 16-bit/ 16-bit instructions take the same number of cycles to execute. There are additional instructions: DIV2 and DIVF2. Divide instructions will complete in six cycles.  2017-2019 Microchip Technology Inc. DS70005319D-page 45 dsPIC33CH128MP508 FAMILY 3.2 Master Memory Organization Note: 3.2.1 The program address memory space of the dsPIC33CH128MP508 family devices is 4M instructions. The space is addressable by a 24-bit value derived either from the 23-bit PC during program execution, or from table operation or Data Space remapping, as described in Section 3.2.9 “Interfacing Program and Data Memory Spaces”. This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “dsPIC33/PIC24 Program Memory” (www.microchip.com/DS70000613) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). User application access to the program memory space is restricted to the lower half of the address range (0x000000 to 0x7FFFFF). The exception is the use of TBLRD operations, which use TBLPAG[7] to permit access to calibration data and Device ID sections of the configuration memory space. The dsPIC33CH128MP508 family architecture features separate program and data memory spaces, and buses. This architecture also allows the direct access of program memory from the Data Space (DS) during code execution. The program memory maps for the Master dsPIC33CHXXXMPX08 device are shown in Figure 3-3 and Figure 3-4. PROGRAM MEMORY MAP FOR MASTER dsPIC33CH128MPXXX DEVICES(1) User Memory Space FIGURE 3-3: PROGRAM ADDRESS SPACE GOTO Instruction 0x000000 Reset Address 0x000002 0x000004 0x0001FE 0x000200 Interrupt Vector Table User Program Flash Memory (44K instructions) Device Configuration 0x015EFE 0x015F00 0x015FFE 0x016000 Unimplemented (Read ‘0’s) Reserved 0x7FFFFE 0x800000 0x800FFE 0x801000 Configuration Memory Space Calibration Data(2,3) User OTP Memory 0x8017FE 0x801800 Reserved Write Latches 0xF9FFFE 0xFA0000 0xFA0002 0xFA0004 Reserved DEVID Reserved Note 1: 0x8016FC 0x801700 0xFEFFFE 0xFF0000 0xFF0002 0xFF0004 0xFFFFFE Memory areas are not shown to scale. 2: Calibration data area must be maintained during programming. 3: Calibration data area includes UDID locations. DS70005319D-page 46  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 3-4: PROGRAM MEMORY MAP FOR MASTER dsPIC33CH64MPXXX DEVICES(1) GOTO Instruction 0x000000 Reset Address 0x000002 0x000004 0x0001FE 0x000200 User Memory Space Interrupt Vector Table User Program Flash Memory (22K instructions) Device Configuration 0x00AEFE 0x00AF00 0x00AFFE 0x00B000 Unimplemented (Read ‘0’s) Reserved 0x7FFFFE 0x800000 0x800FFE 0x800100 Configuration Memory Space Calibration Data(2,3) User OTP Memory Reserved Write Latches 0x8017FE 0x801800 0xF9FFFE 0xFA0000 0xFA0002 0xFA0004 Reserved DEVID Reserved Note 1: 0x8016FC 0x801700 0xFEFFFE 0xFF0000 0xFF0002 0xFF0004 0xFFFFFE Memory areas are not shown to scale. 2: Calibration data area must be maintained during programming. 3: Calibration data area includes UDID locations.  2017-2019 Microchip Technology Inc. DS70005319D-page 47 dsPIC33CH128MP508 FAMILY 3.2.1.1 Program Memory Organization 3.2.1.2 The program memory space is organized in wordaddressable blocks. Although it is treated as 24 bits wide, it is more appropriate to think of each address of the program memory as a lower and upper word, with the upper byte of the upper word being unimplemented. The lower word always has an even address, while the upper word has an odd address (Figure 3-5). All dsPIC33CH128MP508 family devices reserve the addresses between 0x000000 and 0x000200 for hardcoded program execution vectors. A hardware Reset vector is provided to redirect code execution from the default value of the PC on device Reset to the actual start of code. A GOTO instruction is programmed by the user application at address, 0x000000, of Flash memory, with the actual address for the start of code at address, 0x000002, of Flash memory. Program memory addresses are always word-aligned on the lower word, and addresses are incremented or decremented, by two, during code execution. This arrangement provides compatibility with data memory space addressing and makes data in the program memory space accessible. FIGURE 3-5: A more detailed discussion of the Interrupt Vector Tables (IVTs) is provided in Section 3.5 “Master Interrupt Controller”. PROGRAM MEMORY ORGANIZATION least significant word most significant word msw Address 23 0x000001 0x000003 0x000005 0x000007 16 8 PC Address (lsw Address) 0 0x000000 0x000002 0x000004 0x000006 00000000 00000000 00000000 00000000 Program Memory ‘Phantom’ Byte (read as ‘0’) 3.2.2 Interrupt and Trap Vectors UNIQUE DEVICE IDENTIFIER (UDID) All dsPIC33CH128MP508 family devices are individually encoded during final manufacturing with a Unique Device Identifier or UDID. The UDID cannot be erased by a bulk erase command or any other user-accessible means. This feature allows for manufacturing traceability of Microchip Technology devices in applications where this is a requirement. It may also be used by the application manufacturer for any number of things that may require unique identification, such as: • Tracking the device • Unique serial number • Unique security key Instruction Width The UDID is stored in five read-only locations, located between 0x801200 and 0x801208 in the device configuration space. Table 3-3 lists the addresses of the identifier words and shows their contents TABLE 3-3: UDID ADDRESSES UDID Address Description UDID1 0x801200 UDID Word 1 UDID2 0x801202 UDID Word 2 UDID3 0x801204 UDID Word 3 UDID4 0x801206 UDID Word 4 UDID5 0x801208 UDID Word 5 The UDID comprises five 24-bit program words. When taken together, these fields form a unique 120-bit identifier. DS70005319D-page 48  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.2.3 DATA ADDRESS SPACE (MASTER) The dsPIC33CH128MP508 family CPU has a separate 16-bit wide data memory space. The Data Space is accessed using separate Address Generation Units (AGUs) for read and write operations. The data memory map is shown in Figure 3-6. All Effective Addresses (EAs) in the data memory space are 16 bits wide and point to bytes within the Data Space. This arrangement gives a base Data Space address range of 64 Kbytes or 32K words. The lower half of the data memory space (i.e., when EA[15] = 0) is used for implemented memory addresses, while the upper half (EA[15] = 1) is reserved for the Program Space Visibility (PSV). The dsPIC33CH128MP508 family devices implement up to 16 Kbytes of data memory. If an EA points to a location outside of this area, an all-zero word or byte is returned. 3.2.3.1 Data Space Width The data memory space is organized in byteaddressable, 16-bit wide blocks. Data are aligned in data memory and registers as 16-bit words, but all Data Space EAs resolve to bytes. The Least Significant Bytes (LSBs) of each word have even addresses, while the Most Significant Bytes (MSBs) have odd addresses. 3.2.3.2 Data Memory Organization and Alignment To maintain backward compatibility with PIC® MCU devices and improve Data Space memory usage efficiency, the dsPIC33CH128MP508 family instruction set supports both word and byte operations. As a consequence of byte accessibility, all Effective Address calculations are internally scaled to step through wordaligned memory. For example, the core recognizes that Post-Modified Register Indirect Addressing mode [Ws++] results in a value of Ws + 1 for byte operations and Ws + 2 for word operations. A data byte read, reads the complete word that contains the byte, using the LSb of any EA to determine which byte to select. The selected byte is placed onto the LSB of the data path. That is, data memory and registers are organized as two parallel, byte-wide entities with shared (word) address decode, but separate write lines. Data byte writes only write to the corresponding side of the array or register that matches the byte address.  2017-2019 Microchip Technology Inc. All word accesses must be aligned to an even address. Misaligned word data fetches are not supported, so care must be taken when mixing byte and word operations, or translating from 8-bit MCU code. If a misaligned read or write is attempted, an address error trap is generated. If the error occurred on a read, the instruction underway is completed. If the error occurred on a write, the instruction is executed but the write does not occur. In either case, a trap is then executed, allowing the system and/or user application to examine the machine state prior to execution of the address Fault. All byte loads into any W register are loaded into the LSB; the MSB is not modified. A Sign-Extend (SE) instruction is provided to allow user applications to translate 8-bit signed data to 16-bit signed values. Alternatively, for 16-bit unsigned data, user applications can clear the MSB of any W register by executing a Zero-Extend (ZE) instruction on the appropriate address. 3.2.3.3 SFR Space The first 4 Kbytes of the Near Data Space, from 0x0000 to 0x0FFF, is primarily occupied by Special Function Registers (SFRs). These are used by the dsPIC33CH128MP508 family core and peripheral modules for controlling the operation of the device. SFRs are distributed among the modules that they control and are generally grouped together by module. Much of the SFR space contains unused addresses; these are read as ‘0’. Note: 3.2.3.4 The actual set of peripheral features and interrupts varies by the device. Refer to the corresponding device tables and pinout diagrams for device-specific information. Near Data Space The 8-Kbyte area, between 0x0000 and 0x1FFF, is referred to as the Near Data Space. Locations in this space are directly addressable through a 13-bit absolute address field within all memory direct instructions. Additionally, the whole Data Space is addressable using MOV instructions, which support Memory Direct Addressing mode with a 16-bit address field, or by using Indirect Addressing mode using a Working register as an Address Pointer. DS70005319D-page 49 dsPIC33CH128MP508 FAMILY FIGURE 3-6: DATA MEMORY MAP FOR dsPIC33CH128MP508 DEVICES MSB Address MSB 4-Kbyte SFR Space LSB Address 16 Bits LSB 0x0000 0x0001 SFR Space 0x0FFE 0x0FFF 0x1001 X Data RAM (X) (8K) 16-Kbyte SRAM Space 8-Kbyte Near Data Space 0x2000 0x2FFE 0x3000 0x2FFF 0x3001 Y Data RAM (Y) (8K) 0x4FFF 0x5001 0x4FFE 0x5000 0x8001 0x8000 X Data Unimplemented (X) Optionally Mapped into Program Memory 0xFFFF Note: 0xFFFE Memory areas are not shown to scale. DS70005319D-page 50  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.2.3.5 X and Y Data Spaces The dsPIC33CH128MP508 family core has two Data Spaces, X and Y. These Data Spaces can be considered either separate (for some DSP instructions) or as one unified linear address range (for MCU instructions). The Data Spaces are accessed using two Address Generation Units (AGUs) and separate data paths. This feature allows certain instructions to concurrently fetch two words from RAM, thereby enabling efficient execution of DSP algorithms, such as Finite Impulse Response (FIR) filtering and Fast Fourier Transform (FFT). The X Data Space is used by all instructions and supports all addressing modes. X Data Space has separate read and write data buses. The X read data bus is the read data path for all instructions that view Data Space as combined X and Y address space. It is also the X data prefetch path for the dual operand DSP instructions (MAC class). The Y Data Space is used in concert with the X Data Space by the MAC class of instructions (CLR, ED, EDAC, MAC, MOVSAC, MPY, MPY.N and MSC) to provide two concurrent data read paths.  2017-2019 Microchip Technology Inc. Both the X and Y Data Spaces support Modulo Addressing mode for all instructions, subject to addressing mode restrictions. Bit-Reversed Addressing mode is only supported for writes to X Data Space. All data memory writes, including in DSP instructions, view Data Space as combined X and Y address space. The boundary between the X and Y Data Spaces is device-dependent and is not user-programmable. 3.2.4 MEMORY RESOURCES Many useful resources are provided on the main product page of the Microchip website for the devices listed in this data sheet. This product page contains the latest updates and additional information. 3.2.4.1 Key Resources • “Enhanced CPU” (www.microchip.com/ DS70005158) in the “dsPIC33/PIC24 Family Reference Manual” • Code Samples • Application Notes • Software Libraries • Webinars • All Related “dsPIC33/PIC24 Family Reference Manual” Sections • Development Tools DS70005319D-page 51 dsPIC33CH128MP508 FAMILY 3.2.5 SFR MAPS The following tables show dsPIC33CH128MP508 family Master SFR names, addresses and Reset values. These tables contain all registers applicable to TABLE 3-4: Register the dsPIC33CH128MP508 family. Not all registers are present on all device variants. Refer to Table 1 and Table 2 for peripheral availability. Table 4-25 shows port availability for the different package options. MASTER SFR BLOCK 000h Address All Resets Register Address MODCON 046 00--000000000000 CRC WREG0 000 0000000000000000 XMODSRT 048 xxxxxxxxxxxxxxx0 WREG1 002 0000000000000000 XMODEND 04A xxxxxxxxxxxxxxx1 WREG2 004 0000000000000000 YMODSRT 04C xxxxxxxxxxxxxxx0 CRCXORL WREG3 006 0000000000000000 YMODEND 04E xxxxxxxxxxxxxxx1 WREG4 008 0000000000000000 XBREV 050 0xxxxxxxxxxxxxxx WREG5 00A 0000000000000000 DISICNT 052 WREG6 00C 0000000000000000 TBLPAG WREG7 00E 0000000000000000 WREG8 010 0000000000000000 Core All Resets Register Address All Resets CRCCONL 0B0 0-000000010000-- CRCCONH 0B2 ---00000---00000 0B4 000000000000000- CRCXORH 0B6 0000000000000000 CRCDATL 0B8 0000000000000000 xxxxxxxxxxxxxx00 CRCDATH 0BA 0000000000000000 054 --------00000000 CRCWDATL 0BC 0000000000000000 YPAG 056 --------00000001 CRCWDATH 0BE 0000000000000000 MSTRPR 058 ----------00---0 CLC WREG9 012 0000000000000000 CTXTSTAT 05A 0000000000000000 CLC1CONL 0C0 0-0-00--000--000 WREG10 014 0000000000000000 DMTCON 05C 0000000000000000 CLC1CONH 0C2 ------------0000 WREG11 016 0000000000000000 DMTPRECLR 060 0000000000000000 CLC1SEL 0C4 -000-000-000-000 WREG12 018 0000000000000000 DMTCLR 064 0000000000000000 CLC1GLSL 0C8 0000000000000000 WREG13 01A 0000000000000000 DMTSTAT 068 0000000000000000 CLC1GLSH 0CA 0000000000000000 WREG14 01C 0000000000000000 DMTCNTL 06C 0000000000000000 CLC2CONL 0CC 0-0-00--000--000 WREG15 01E 0000100000000000 DMTCNTH 06E 0000000000000000 CLC2CONH 0CE ------------0000 SPLIM 020 xxxxxxxxxxxxxxxx DMTHOLDREG 070 0000000000000000 CLC2SEL 0D0 -000-000-000-000 ACCAL 022 xxxxxxxxxxxxxxxx DMTPSCNTL 074 0000000000000000 CLC2GLSL 0D4 0000000000000000 ACCAH 024 xxxxxxxxxxxxxxxx DMTPSCNTH 076 0000000000000000 CLC2GLSH 0D6 0000000000000000 ACCAU 026 xxxxxxxxxxxxxxxx DMTPSINTVL 078 0000000000000000 CLC3CONL 0D8 0-0-00--000--000 ACCBL 028 xxxxxxxxxxxxxxxx DMTPSINTVH 07A 0000000000000000 CLC3CONH 0DA ------------0000 ACCBH 02A xxxxxxxxxxxxxxxx SENT CLC3SEL 0DC -000-000-000-000 ACCBU 02C xxxxxxxxxxxxxxxx SENT1CON1 080 0000000000000000 CLC3GLSL 0E0 0000000000000000 PCL 02E 0000000000000000 SENT1CON2 084 0000000000000000 CLC3GLSH 0E2 0000000000000000 PCH 030 --------00000000 SENT1CON3 088 0000000000000000 CLC4CONL 0E4 0-0-00--000--000 DSRPAG 032 ------0000000001 SENT1STAT 08C 0000000000000000 CLC4CONH 0E6 ------------0000 DSWPAG 034 -----00000000001 SENT1SYNC 090 0000000000000000 CLC4SEL 0E8 -000-000-000-000 RCOUNT 036 xxxxxxxxxxxxxxxx SENT1DATL 094 0000000000000000 CLC4GLSL 0EC 0000000000000000 DCOUNT 038 xxxxxxxxxxxxxxxx SENT1DATH 096 0000000000000000 CLC4GLSH 0EE 0000000000000000 DOSTART 03A 1111111111111111 SENT2CON1 098 0000000000000000 ECCCONL 0F0 ---------------0 DOSTARTL 03A 1111111111111110 SENT2CON2 09C 0000000000000000 ECCCONH 0F2 0000000000000000 DOSTARTH 03C 0000000011111111 SENT2CON3 0A0 0000000000000000 ECCADDRL 0F4 0000000000000000 DOENDL 03E xxxxxxxxxxxxxxx0 SENT2STAT 0A4 0000000000000000 ECCADDRH 0F6 0000000000000000 DOENDH 040 ---------xxxxxxx SENT2SYNC 0A8 0000000000000000 ECCSTATL 0F8 0000000000000000 SR 042 0000000000000000 SENT2DATL 0AC 0000000000000000 ECCSTATH 0FA ------0000000000 CORCON 044 x-xx000000100000 SENT2DATH 0AE 0000000000000000 Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively. Note 1: SFR shown is for the superset 80-pin device. DS70005319D-page 52  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 3-5: Register MASTER SFR BLOCK 100h Address All Resets Register Address All Resets Register Address All Resets T1CON 100 0-0000000-00-00- INT1TMRH 15E 0000000000000000 MSI1MBX3D 1E0 0000000000000000 INT1HLDL 160 0000000000000000 MSI1MBX4D 1E2 TMR1 104 0000000000000000 0000000000000000 INT1HLDH 162 0000000000000000 MSI1MBX5D 1E4 PR1 108 0000000000000000 0000000000000000 INDX1CNTL 164 0000000000000000 MSI1MBX6D 1E6 0000000000000000 INDX1CNTH 166 0000000000000000 MSI1MBX7D 1E8 0000000000000000 0000000000000000 Timers QEI QEI1CON 140 0000000000000000 INDX1HLDL 168 0000000000000000 MSI1MBX8D 1EA QEI1IOCL 144 000000000000xxxx INDX1HLDH 16A 0000000000000000 MSI1MBX9D 1EC 0000000000000000 QEI1IOCH 146 ---------------0 QEI1GECL 16C 0000000000000000 MSI1MBX10D 1EE 0000000000000000 QEI1STAT 148 --00000000000000 QEI1GECH 16E 0000000000000000 MSI1MBX11D 1F0 0000000000000000 POS1CNTL 14C 0000000000000000 QEI1LECL 170 0000000000000000 MSI1MBX12D 1F2 0000000000000000 POS1CNTH 14E 0000000000000000 QEI1LECH 172 0000000000000000 MSI1MBX13D 1F4 0000000000000000 POS1HLDL 150 0000000000000000 MSI1CON 1D2 0---xx0000000000 MSI1MBX14D 1F6 0000000000000000 POS1HLDH 152 0000000000000000 MSI1STAT 1D4 0000000000000000 MSI1MBX15D 1F8 0000000000000000 VEL1CNTL 154 0000000000000000 MSI1KEY 1D6 --------00000000 MSI1FIFOCS 1FA 0---00000---0000 VEL1CNTH 156 0000000000000000 MSI1MBXS 1D8 --------00000000 MRSWFDATA 1FC 0000000000000000 VEL1HLDL 158 0000000000000000 MSI1MBX0D 1DA 0000000000000000 MWSRFDATA 1FE 0000000000000000 VEL1HLDH 15A 0000000000000000 MSI1MBX1D 1DC 0000000000000000 INT1TMRL 15C 0000000000000000 MSI1MBX2D 1DE 0000000000000000 Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively.  2017-2019 Microchip Technology Inc. DS70005319D-page 53 dsPIC33CH128MP508 FAMILY TABLE 3-6: Register MASTER SFR BLOCK 200h Address All Resets Register Address U1P2 200 0-01000000000000 U1P3 2C I I2C1CONL All Resets Register Address All Resets 24E -------000000000 SPI1CON1H 2AE 0000000000000000 250 0000000000000000 SPI1CON2L 2B0 -----------00000 ---------------- I2C1CONH 202 ---------0000000 U1P3H 252 --------00000000 SPI1CON2H 2B2 I2C1STAT 204 000--00000000000 U1TXCHK 254 --------00000000 SPI1STATL 2B4 ---00--0001-1-00 I2C1ADD 208 ------0000000000 U1RXCHK 256 --------00000000 SPI1STATH 2B6 --000000--000000 I2C1MSK 20C ------0000000000 U1SCCON 258 ----------00000- SPI1BUFL 2B8 0000000000000000 I2C1BRG 210 0000000000000000 U1SCINT 25A --00-000--00-000 SPI1BUFH 2BA 0000000000000000 I2C1TRN 214 --------11111111 U1INT 25C --------00---0-- SPI1BRGL 2BC ---xxxxxxxxxxxxx I2C1RCV 218 --------00000000 U2MODE 260 0-000-0000000000 SPI1BRGH 2BE ---------------- I2C2CONL 21C 0-01000000000000 U2MODEH 262 00---00000000000 SPI1IMSKL 2C0 ---00--0000-0-00 I2C2CONH 21E ---------0000000 U2STA 264 0000000010000000 SPI1IMSKH 2C2 0-0000000-000000 I2C2STAT 220 000--00000000000 U2STAH 266 -000-00000101110 SPI1URDTL 2C4 0000000000000000 I2C2ADD 224 ------0000000000 U2BRG 268 0000000000000000 SPI1URDTH 2C6 0000000000000000 I2C2MSK 228 ------0000000000 U2BRGH 26A ------------0000 SPI2CON1L 2C8 0-00000000000000 I2C2BRG 22C 0000000000000000 U2RXREG 26C --------xxxxxxxx SPI2CON1H 2CA 0000000000000000 I2C2TRN 230 --------11111111 U2TXREG 270 -------xxxxxxxxx SPI2CON2L 2CC -----------00000 I2C2RCV 234 --------00000000 U2P1 274 -------000000000 SPI2CON2H 2CE ---------------- U2P2 276 -------000000000 SPI2STATL 2D0 ---00--0001-1-00 238 0-000-0000000000 U2P3 278 0000000000000000 SPI2STATH 2D2 --000000--000000 0000000000000000 UART U1MODE U1MODEH 23A 00---00000000000 U2P3H 27A --------00000000 SPI2BUFL 2D4 U1STA 23C 0000000010000000 U2TXCHK 27C --------00000000 SPI2BUFH 2D6 0000000000000000 U1STAH 23E -000-00000101110 U2RXCHK 27E --------00000000 SPI2BRGL 2D8 ---xxxxxxxxxxxxx U1BRG 240 0000000000000000 U2SCCON 280 ----------00000- SPI2BRGH 2DA ---------------- U1BRGH 242 ------------0000 U2SCINT 282 --00-000--00-000 SPI2IMSKL 2DC ---00--0000-0-00 U1RXREG 244 --------xxxxxxxx U2INT 284 --------00---0-- SPI2IMSKH 2DE 0-0000000-000000 U1TXREG 248 -------xxxxxxxxx SPI SPI2URDTL 2E0 0000000000000000 U1P1 24C -------000000000 SPI1CON1L SPI2URDTH 2E2 0000000000000000 2AC 0-00000000000000 Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively. DS70005319D-page 54  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 3-7: Register MASTER SFR BLOCK 300h-400h Address All Resets Register High-Speed PWM Address All Resets Register Address All Resets 0000-00000000000 PG1TRIGB 356 0000000000000000 PG3FFPCIH 3AE PCLKCON 300 00-----0--00--00 PG1TRIGC 358 0000000000000000 PG3SPCIL 3B0 0000000000000000 FSCL 302 0000000000000000 PG1DTL 35A --00000000000000 PG3SPCIH 3B2 0000-00000000000 FSMINPER 304 0000000000000000 PG1DTH 35C --00000000000000 PG3LEBL 3B4 0000000000000000 MPHASE 306 0000000000000000 PG1CAP 35E 0000000000000000 PG3LEBH 3B6 -----000----0000 MDC 308 0000000000000000 PG2CONL 360 0-00000000000000 PG3PHASE 3B8 0000000000000000 MPER 30A 0000000000000000 PG2CONH 362 000-000000--0000 PG3DC 3BA 0000000000000000 LFSR 30C 0000000000000000 PG2STAT 364 0000000000000000 PG3DCA 3BC --------00000000 CMBTRIGL 30E --------00000000 PG2IOCONL 366 0000000000000000 PG3PER 3BE 0000000000000000 CMBTRIGH 310 --------00000000 PG2IOCONH 368 -000---0--000000 PG3TRIGA 3C0 0000000000000000 LOGCONA 312 000000000000-000 PG2EVTL 36A 00000000---00000 PG3TRIGB 3C2 0000000000000000 LOGCONB 314 000000000000-000 PG2EVTH 36C 0000--0000000000 PG3TRIGC 3C4 0000000000000000 LOGCONC 316 000000000000-000 PG2FPCIL 36E 0000000000000000 PG3DTL 3C6 --00000000000000 LOGCOND 318 000000000000-000 PG2FPCIH 370 0000-00000000000 PG3DTH 3C8 --00000000000000 LOGCONE 31A 000000000000-000 PG2CLPCIL 372 0000000000000000 PG3CAP 3CA 0000000000000000 LOGCONF 31C 000000000000-000 PG2CLPCIH 374 0000-00000000000 PG4CONL 3CC 0-00000000000000 PWMEVTA 31E 0000----0000-000 PG2FFPCIL 376 0000000000000000 PG4CONH 3CE 000-000000--0000 PWMEVTB 320 0000----0000-000 PG2FFPCIH 378 0000-00000000000 PG4STAT 3D0 0000000000000000 PWMEVTC 322 0000----0000-000 PG2SPCIL 37A 0000000000000000 PG4IOCONL 3D2 0000000000000000 PWMEVTD 324 0000----0000-000 PG2SPCIH 37C 0000-00000000000 PG4IOCONH 3D4 -000---0--000000 PWMEVTE 326 0000----0000-000 PG2LEBL 37E 0000000000000000 PG4EVTL 3D6 00000000---00000 PWMEVTF 328 0000----0000-000 PG2LEBH 380 -----000----0000 PG4EVTH 3D8 0000--0000000000 PG1CONL 32A 0-00000000000000 PG2PHASE 382 0000000000000000 PG4FPCIL 3DA 0000000000000000 PG1CONH 32C 000-000000--0000 PG2DC 384 0000000000000000 PG4FPCIH 3DC 0000-00000000000 PG1STAT 32E 0000000000000000 PG2DCA 386 --------00000000 PG4CLPCIL 3DE 0000000000000000 PG1IOCONL 330 0000000000000000 PG2PER 388 0000000000000000 PG4CLPCIH 3E0 0000-00000000000 PG1IOCONH 332 -000---0--000000 PG2TRIGA 38A 0000000000000000 PG4FFPCIL 3E2 0000000000000000 0000-00000000000 PG1EVTL 334 00000000---00000 PG2TRIGB 38C 0000000000000000 PG4FFPCIH 3E4 PG1EVTH 336 0000--0000000000 PG2TRIGC 38E 0000000000000000 PG4SPCIL 3E6 0000000000000000 PG1FPCIL 338 0000000000000000 PG2DTL 390 --00000000000000 PG4SPCIH 3E8 0000-00000000000 PG1FPCIH 33A 0000-00000000000 PG2DTH 392 --00000000000000 PG4LEBL 3EA 0000000000000000 PG1CLPCIL 33C 0000000000000000 PG2CAP 394 0000000000000000 PG4LEBH 3EC -----000----0000 PG1CLPCIH 33E 0000-00000000000 PG3CONL 396 0-00000000000000 PG4PHASE 3EE 0000000000000000 PG1FFPCIL 340 0000000000000000 PG3CONH 398 000-000000--0000 PG4DC 3F0 0000000000000000 PG1FFPCIH 342 0000-00000000000 PG3STAT 39A 0000000000000000 PG4DCA 3F2 --------00000000 PG1SPCIL 344 0000000000000000 PG3IOCONL 39C 0000000000000000 PG4PER 3F4 0000000000000000 PG1SPCIH 346 0000-00000000000 PG3IOCONH 39E -000---0--000000 PG4TRIGA 3F6 0000000000000000 PG1LEBL 348 0000000000000000 PG3EVTL 3A0 00000000---00000 PG4TRIGB 3F8 0000000000000000 PG1LEBH 34A -----000----0000 PG3EVTH 3A2 0000--0000000000 PG4TRIGC 3FA 0000000000000000 PG1PHASE 34C 0000000000000000 PG3FPCIL 3A4 0000000000000000 PG4DTL 3FC --00000000000000 PG1DC 34E 0000000000000000 PG3FPCIH 3A6 0000-00000000000 PG4DTH 3FE --00000000000000 PG1DCA 350 --------00000000 PG3CLPCIL 3A8 0000000000000000 PG4CAP 400 0000000000000000 PG1PER 352 0000000000000000 PG3CLPCIH 3AA 0000-00000000000 PG1TRIGA 354 0000000000000000 PG3FFPCIL 3AC 0000000000000000 Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively.  2017-2019 Microchip Technology Inc. DS70005319D-page 55 dsPIC33CH128MP508 FAMILY TABLE 3-8: Register MASTER SFR BLOCK 500h Address All Resets Register C1TSCONL 5C0 0-00011101100000 C1TSCONH CAN FD C1CONL Address All Resets Register Address All Resets 5D4 ------0000000000 C1RXOVIFH 5EA 0000000000000000 5D6 -------------000 C1TXATIFL 5EC 0000000000000000 C1CONH 5C2 0000010010011000 C1VECL 5D8 ---00000-1000000 C1TXATIFH 5EE 0000000000000000 C1NBTCFGL 5C4 -0001111-0001111 C1VECH 5DA -10000---1000000 C1TXREQL 5F0 0000000000000000 C1NBTCFGH 5C6 0000000000111110 C1INTL 5DC 000000-----00000 C1TXREQH 5F2 0000000000000000 C1DBTCFGL 5C8 ----0011----0011 C1INTH 5DE 00000000---00000 C1TRECL 5F4 0000000000000000 C1DBTCFGH 5CA 00000000---01110 C1RXIFL 5E0 000000000000000- C1TRECH 5F6 ----------100000 C1TDCL 5CC -0010000--000000 C1RXIFH 5E2 0000000000000000 C1BDIAG0L 5F8 0000000000000000 C1TDCH 5CE ------00------10 C1TXIFL 5E4 0000000000000000 C1BDIAG0H 5FA 0000000000000000 C1TBCL 5D0 0000000000000000 C1TXIFH 5E6 0000000000000000 C1BDIAG1L 5FC 0000000000000000 C1TBCH 5D2 0000000000000000 C1RXOVIFL 5E8 000000000000000- C1BDIAG1H 5FE 00000-000-000000 Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively. DS70005319D-page 56  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 3-9: Register MASTER SFR BLOCK 600h Address All Resets CAN FD (Continued) Register Address All Resets Register Address All Resets C1FIFOCON6H 65A 00000000-1100000 C1MASK5L 6AC 0000000000000000 C1TEFCONL 600 -----100--0-0000 C1FIFOSTA6 65C ---0000000000000 C1MASK5H 6AE 0000000000000000 C1TEFCONH 602 ---00000-------- C1FIFOUA6L 660 xxxxxxxxxxxxxxxx C1FLTOBJ6L 6B0 0000000000000000 C1TEFSTA 604 ------------0000 C1FIFOUA6H 662 xxxxxxxxxxxxxxxx C1FLTOBJ6H 6B2 0000000000000000 C1TEFUAL 608 xxxxxxxxxxxxxxxx C1FIFOCON7L 664 -----10000000000 C1MASK6L 6B4 0000000000000000 C1TEFUAH 60A xxxxxxxxxxxxxxxx C1FIFOCON7H 666 00000000-1100000 C1MASK6H 6B6 0000000000000000 C1FIFOBAL 60C 0000000000000000 C1FIFOSTA7 668 ---0000000000000 C1FLTOBJ7L 7B8 0000000000000000 C1FIFOBAH 60E 0000000000000000 C1FIFOUA7L 66C xxxxxxxxxxxxxxxx C1FLTOBJ7H 6BA 0000000000000000 C1TXQCONL 610 -----1001--0-0-0 C1FIFOUA7H 66E xxxxxxxxxxxxxxxx C1MASK7L 6BC 0000000000000000 C1TXQCONH 612 00000000-1100000 C1FLTCON0L 670 0--000000--00000 C1MASK7H 6BE 0000000000000000 C1TXQSTA 614 ---000000000-0-0 C1FLTCON0H 672 0--000000--00000 C1FLTOBJ8L 6C0 0000000000000000 C1TXQUAL 618 xxxxxxxxxxxxxxxx C1FLTCON1L 674 0--000000--00000 C1FLTOBJ8H 6C2 0000000000000000 C1TXQUAH 61A xxxxxxxxxxxxxxxx C1FLTCON1H 676 0--000000--00000 C1MASK8L 6C4 0000000000000000 C1FIFOCON1L 61C -----10000000000 C1FLTCON2L 678 0--000000--00000 C1MASK8H 6C6 0000000000000000 C1FIFOCON1H 61E 00000000-1100000 C1FLTCON2H 67A 0--000000--00000 C1FLTOBJ9L 6C8 0000000000000000 C1FIFOSTA1 620 ---0000000000000 C1FLTCON3L 67C 0--000000--00000 C1FLTOBJ9H 6CA 0000000000000000 C1FIFOUA1L 624 xxxxxxxxxxxxxxxx C1FLTCON3H 67E 0--000000--00000 C1MASK9L 6CC 0000000000000000 C1MASK9H 6CE 0000000000000000 6D0 0000000000000000 C1FIFOUA1H 626 xxxxxxxxxxxxxxxx C1FLTOBJ0L 680 0000000000000000 C1FIFOCON2L 628 -----10000000000 C1FLTOBJ0H 682 0000000000000000 C1FLTOBJ10L C1FIFOCON2H 62A 00000000-1100000 C1MASK0L 684 0000000000000000 C1FLTOBJ10H 6D2 0000000000000000 C1FIFOSTA2 62C ---0000000000000 C1MASK0H 686 0000000000000000 C1MASK10L 6D4 0000000000000000 C1FIFOUA2L 630 xxxxxxxxxxxxxxxx C1FLTOBJ1L 688 0000000000000000 C1MASK10H 6D6 0000000000000000 C1FIFOUA2H 632 xxxxxxxxxxxxxxxx C1FLTOBJ1H 68A 0000000000000000 C1FLTOBJ11L 6D8 0000000000000000 C1FIFOCON3L 634 -----10000000000 C1MASK1L 68C 0000000000000000 C1FLTOBJ11H 6DA 0000000000000000 C1FIFOCON3H 636 00000000-1100000 C1MASK1H 68E 0000000000000000 C1MASK11L 6DC 0000000000000000 C1MASK11H C1FIFOSTA3 638 ---0000000000000 C1FLTOBJ2L 690 0000000000000000 6DE 0000000000000000 C1FIFOUA3L 63C xxxxxxxxxxxxxxxx C1FLTOBJ2H 692 0000000000000000 C1FLTOBJ12L 6E0 0000000000000000 C1FIFOUA3H 63E xxxxxxxxxxxxxxxx C1MASK2L 694 0000000000000000 C1FLTOBJ12H 6E2 0000000000000000 C1FIFOCON4L 640 -----10000000000 C1MASK2H 696 0000000000000000 C1MASK12L 6E4 0000000000000000 C1FIFOCON4H 642 00000000-1100000 C1FLTOBJ3L 698 0000000000000000 C1MASK12H 6E6 0000000000000000 C1FIFOSTA4 644 ---0000000000000 C1FLTOBJ3H 69A 0000000000000000 C1FLTOBJ13L 6E8 0000000000000000 C1FIFOUA4L 648 xxxxxxxxxxxxxxxx C1MASK3L 69C 0000000000000000 C1FLTOBJ13H 6EA 0000000000000000 C1FIFOUA4H 64A xxxxxxxxxxxxxxxx C1MASK3H 69C 0000000000000000 C1MASK13L 6EC 0000000000000000 C1FIFOCON5L 64C -----10000000000 C1FLTOBJ4L 6A0 0000000000000000 C1MASK13H 6EE 0000000000000000 C1FIFOCON5H 64E 00000000-1100000 C1FLTOBJ4H 6A2 0000000000000000 C1FLTOBJ14L 6F0 0000000000000000 C1FIFOSTA5 650 ---0000000000000 C1MASK4L 6A4 0000000000000000 C1FLTOBJ14H 6F2 0000000000000000 C1FIFOUA5L 654 xxxxxxxxxxxxxxxx C1MASK4H 6A6 0000000000000000 C1FIFOUA5H 656 xxxxxxxxxxxxxxxx C1FLTOBJ5L 6A8 0000000000000000 C1FIFOCON6L 658 -----10000000000 C1FLTOBJ5H 6AA 0000000000000000 Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively.  2017-2019 Microchip Technology Inc. DS70005319D-page 57 dsPIC33CH128MP508 FAMILY TABLE 3-10: Register MASTER SFR BLOCK 700h Address All Resets CAN FD (Continued) Register Address All Resets Register Address All Resets C1MASK15H 6FE -000000000000000 C1FLTOBJ15L 6F8 0000000000000000 C1MASK14L 6F4 0000000000000000 C1FLTOBJ15H 6FA -000000000000000 C1MASK14H 6F6 -000000000000000 6FC 0000000000000000 C1MASK15L Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively. TABLE 3-11: Register MASTER SFR BLOCK 800h Address All Resets Register IPC3 846 -100-100-100-100 IPC33 882 -100-100-100-100 800 0000000000-00000 IPC4 848 -100-100-100-100 IPC34 884 -100-100-100-100 Interrupts IFS0 Address All Resets Register Address All Resets IFS1 802 0000000000000000 IPC5 84A -100-100-100-100 IPC35 886 ---------100-100 IFS2 804 00000-00-00000-- IPC6 84C -100-100-100-100 IPC35 886 ---------100-100 IFS3 806 000--------00000 IPC7 84E -100-100-100-100 IPC36 888 -----100-------- IFS4 808 --000----0000-00 IPC8 850 -100-100-------- IPC37 88A -----100-100------------100-100 IFS5 80A 000000000000000- IPC9 852 -----100-100-100 IPC38 88C IFS6 80C 0000000000000000 IPC10 854 -100-----100-100 IPC39 88E ---------100---- IFS7 80E 0000000000000--- IPC11 856 -100-100-100-100 IPC42 894 -100-100-100-100 IFS8 810 --0000000000000- IPC12 858 -100-100-100-100 IPC43 896 -100-100-100-100 IFS9 812 --0---00-00--0-- IPC13 85A -------------100 IPC44 898 -100-100-100-100 IFS10 814 00000000-------- IPC15 85E -100-100-100---- IPC45 89A -------------100 IFS11 816 -00--------00000 IPC16 860 -100-----100-100 IPC47 89E -----100-100---- IEC0 820 0000000000-00000 IPC17 862 -----100-100-100 INTCON1 8C0 000000000000000- IEC1 822 0000000000000000 IPC18 864 -100------------ INTCON2 8C2 000----0----0000 IEC2 824 00000-00-00000-- IPC19 866 ---------100-100 INTCON3 8C4 -------0---0---0 IEC3 826 000--------00000 IPC20 868 -100-100-100---- INTCON4 8C6 --------------00 IEC4 828 --000----0000-00 IPC21 86A -100-100-100-100 INTTREG 8C8 000-000000000000 IEC5 82A 000000000000000- IPC22 86C -100-100-100-100 Flash IEC6 82C 0000000000000000 IPC23 86E -100-100-100-100 NVMCON 8D0 0000--00----0000 IEC7 82E 0000000000000--- IPC24 870 -100-100-100-100 NVMADR 8D2 0000000000000000 IEC8 830 --0000000000000- IPC25 872 -100-100-100-100 NVMADRU 8D4 --------00000000 IEC8 830 --0000000000000- IPC26 874 -100-100-100-100 NVMKEY 8D6 --------00000000 IEC9 832 --0---00-00--0-- IPC27 876 -100-100-100-100 NVMSRCADRL 8D8 0000000000000000 IEC10 834 00000000------00 IPC28 878 -100------------ NVMSRCADRH 8DA --------00000000 IEC11 836 -00--------00000 IPC29 87A -100-100-100-100 CBG IPC0 840 -100-100-100-100 IPC30 87C -100-100-100-100 BIASCON 8F0 --------0---0000 IPC1 842 -100-100-----100 IPC31 87E -100-100-100-100 IBIASCONL 8F4 --000000--000000 IPC2 844 -100-100-100-100 IPC32 880 -100-100-100---- IBIASCONH 8F6 --000000--000000 Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively. DS70005319D-page 58  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 3-12: Register MASTER SFR BLOCK 900h Address All Resets PTG Register Address All Resets Register Address All Resets 0000000000000000 CCP1CON2L 954 00-0----00000000 CCP3TMRH 9AA PTGCST 900 0-00-00000x---00 CCP1CON2H 956 0------100-00000 CCP3PRL 9AC 1111111111111111 PTGCON 902 -----00000000000 CCP1CON3H 95A 0000------0-00-- CCP3PRH 9AE 1111111111111111 PTGBTE 904 xxxxxxxxxxxxxxxx CCP1STATL 95C -----0--00xx0000 CCP3RAL 9B0 0000000000000000 PTGBTEH 906 ---------------- CCP1TMRL 960 0000000000000000 CCP3RBL 9B4 0000000000000000 PTGHOLD 908 0000000000000000 CCP1TMRH 962 0000000000000000 CCP3BUFL 9B8 0000000000000000 PTGT0LIM 90C 0000000000000000 CCP1PRL 964 1111111111111111 CCP3BUFH 9BA 0000000000000000 PTGT1LIM 910 0000000000000000 CCP1PRH 966 1111111111111111 CCP4CON1L 9BC 0-00000000000000 PTGSDLIM 914 0000000000000000 CCP1RAL 968 0000000000000000 CCP4CON1H 9BE 00--000000000000 PTGC0LIM 918 0000000000000000 CCP1RBL 96C 0000000000000000 CCP4CON2L 9C0 00-0----00000000 PTGC1LIM 91C 0000000000000000 CCP1BUFL 970 0000000000000000 CCP4CON2H 9C2 0------100-00000 PTGADJ 920 0000000000000000 CCP1BUFH 972 0000000000000000 CCP4CON3H 9C6 0000------0-00-- PTGL0 924 0000000000000000 CCP2CON1L 974 0-00000000000000 CCP4STATL 9C8 -----0--00xx0000 PTGQPTR 928 -----------00000 CCP2CON1H 976 00--000000000000 CCP4TMRL 9CC 0000000000000000 PTGQUE0 930 xxxxxxxxxxxxxxxx CCP2CON2L 978 00-0----00000000 CCP4TMRH 9CE 0000000000000000 PTGQUE1 932 xxxxxxxxxxxxxxxx CCP2CON2H 97A 0------100-00000 CCP4PRL 9D0 1111111111111111 PTGQUE2 934 xxxxxxxxxxxxxxxx CCP2CON3H 97E 0000------0-00-- CCP4PRH 9D2 1111111111111111 PTGQUE3 936 xxxxxxxxxxxxxxxx CCP2STATL 980 -----0--00xx0000 CCP4RAL 9D4 0000000000000000 PTGQUE4 938 xxxxxxxxxxxxxxxx CCP2TMRL 984 0000000000000000 CCP4RBL 9D8 0000000000000000 PTGQUE5 93A xxxxxxxxxxxxxxxx CCP2TMRH 986 0000000000000000 CCP4BUFL 9DC 0000000000000000 PTGQUE6 93C xxxxxxxxxxxxxxxx CCP2PRL 988 1111111111111111 CCP4BUFH 9DE 0000000000000000 PTGQUE7 93E xxxxxxxxxxxxxxxx CCP2PRH 98A 1111111111111111 CCP5CON1L 9E0 0-00000000000000 PTGQUE8 940 xxxxxxxxxxxxxxxx CCP2RAL 98C 0000000000000000 CCP5CON1H 9E2 00--000000000000 PTGQUE9 942 xxxxxxxxxxxxxxxx CCP2RBL 990 0000000000000000 CCP5CON2L 9E4 00-0----00000000 PTGQUE10 944 xxxxxxxxxxxxxxxx CCP2BUFL 994 0000000000000000 CCP5CON2H 9E6 0------100-00000 0000------0-00-- PTGQUE11 946 xxxxxxxxxxxxxxxx CCP2BUFH 996 0000000000000000 CCP5CON3H 9EA PTGQUE12 948 xxxxxxxxxxxxxxxx CCP3CON1L 998 0-00000000000000 CCP5STATL 9EC -----0--00xx0000 PTGQUE13 94A xxxxxxxxxxxxxxxx CCP3CON1H 99A 00--000000000000 CCP5TMRL 9F0 0000000000000000 PTGQUE14 94C xxxxxxxxxxxxxxxx CCP3CON2L 99C 00-0----00000000 CCP5TMRH 9F2 0000000000000000 PTGQUE15 94E xxxxxxxxxxxxxxxx CCP3CON2H 99E 0------100-00000 CCP5PRL 9F4 1111111111111111 CCP3CON3H 9A2 0000------0-00-- CCP5PRH 9F6 1111111111111111 CCP1CON1L 950 0-00000000000000 CCP3STATL 9A4 -----0--00xx0000 CCP5RAL 9F8 0000000000000000 CCP1CON1H 952 00--000000000000 CCP3TMRL 9A8 0000000000000000 CCP5RBL 9FC 0000000000000000 CCP Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively.  2017-2019 Microchip Technology Inc. DS70005319D-page 59 dsPIC33CH128MP508 FAMILY TABLE 3-13: Register MASTER SFR BLOCK A00h Address All Resets CCP (Continued) Register Address All Resets Register Address All Resets 0000000000000001 CCP7RAL A40 0000000000000000 DMACNT0 ACC CCP5BUFL A00 0000000000000000 CCP7RBL A44 0000000000000000 DMACH1 ACE ---0-00000000000 CCP5BUFH A02 0000000000000000 CCP7BUFL A48 0000000000000000 DMAINT1 AD0 0000000000000--0 CCP6CON1L A04 0-00000000000000 CCP7BUFH A4A 0000000000000000 DMASRC1 AD2 0000000000000000 CCP6CON1H A06 00--000000000000 CCP8CON1L A4C 0-00000000000000 DMADST1 AD4 0000000000000000 CCP6CON2L A08 00-0----00000000 CCP8CON1H A4E 00--000000000000 DMACNT1 AD6 0000000000000001 CCP6CON2H A0A 0------100-00000 CCP8CON2L A50 00-0----00000000 DMACH2 AD8 ---0-00000000000 CCP6CON3H A0E 0000------0-00-- CCP8CON2H A52 0------100-00000 DMAINT2 ADA 0000000000000--0 CCP6STATL A10 -----0--00xx0000 CCP8STATL A58 -----0--00xx0000 DMASRC2 ADC 0000000000000000 CCP6TMRL A14 0000000000000000 CCP8STATH A5A -----------00000 DMADST2 ADE 0000000000000000 CCP6TMRH A16 0000000000000000 CCP8TMRL A5C 0000000000000000 DMACNT2 AE0 0000000000000001 CCP6PRL A18 1111111111111111 CCP8TMRH A5E 0000000000000000 DMACH3 AE2 ---0-00000000000 CCP6PRH A1A 1111111111111111 CCP8PRL A60 1111111111111111 DMAINT3 AE4 0000000000000--0 CCP6RAL A1C 0000000000000000 CCP8PRH A62 1111111111111111 DMASRC3 AE6 0000000000000000 CCP6RBL A20 0000000000000000 CCP8RAL A64 0000000000000000 DMADST3 AE8 0000000000000000 0000000000000001 CCP6BUFL A24 0000000000000000 CCP8RBL A68 0000000000000000 DMACNT3 AEA CCP6BUFH A26 0000000000000000 CCP8BUFL A6C 0000000000000000 DMACH4 AEC ---0-00000000000 CCP7CON1L A28 0-00000000000000 CCP8BUFH A6E 0000000000000000 DMAINT4 AEE 0000000000000--0 CCP7CON1H A2A 00--000000000000 DMA DMASRC4 AF0 0000000000000000 CCP7CON2L A2C 00-0----00000000 DMACON ABC 0--------------0 DMADST4 AF2 0000000000000000 CCP7CON2H A2E 0------100-00000 DMABUF ABE 0000000000000000 DMACNT4 AF4 0000000000000001 CCP7CON3H A32 0000------0-00-- DMAL AC0 0000000000000000 DMACH5 AF6 ---0-00000000000 CCP7STATL A34 -----0--00xx0000 DMAH AC2 0001000000000000 DMAINT5 AF8 0000000000000--0 CCP7TMRL A38 0000000000000000 DMACH0 AC4 ---0-00000000000 DMASRC5 AFA 0000000000000000 CCP7TMRH A3A 0000000000000000 DMAINT0 AC6 0000000000000--0 DMADST5 AFC 0000000000000000 CCP7PRL A3C 1111111111111111 DMASRC0 AC8 0000000000000000 DMACNT5 AFE 0000000000000001 CCP7PRH A3E 1111111111111111 DMADST0 ACA 0000000000000000 Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively. DS70005319D-page 60  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 3-14: Register MASTER SFR BLOCK B00h Address All Resets Register Address All Resets Register Address All Resets ADCON1L B00 000-00000----000 ADCMP1ENH B42 -----------00000 ADTRIG0H B82 0000000000000000 ADCMP1LO B44 0000000000000000 ADTRIG1L B84 ADCON1H B02 --------011----- 0000000000000000 ADCMP1HI B46 0000000000000000 ADTRIG1H B86 ADCON2L B04 0000000000000000 00-0000000000000 ADCMP2ENL B48 0000000000000000 ADTRIG2L B88 ADCON2H 0000000000000000 B06 00-0000000000000 ADCMP2ENH B4A -----------00000 ADTRIG2H B8A 0000000000000000 ADCON3L B08 00000x0000000000 ADCMP2LO B4C 0000000000000000 ADTRIG3L B8C 0000000000000000 ADCON3H B0A 000000000------- ADCMP2HI B4E 0000000000000000 ADTRIG3H B8E 0000000000000000 ADMOD0L B10 -0-0-0-0-0-0-0-0 ADCMP3ENL B50 0000000000000000 ADTRIG4L B90 0000000000000000 ADMOD0H B12 -0-0-0-0-0-0-0-0 ADCMP3ENH B52 -----------00000 ADTRIG4H B92 0000000000000000 ADMOD1L B14 -------0-0-0-0-0 ADCMP3LO B54 0000000000000000 ADTRIG5L B94 000-----00000000 ADIEL B20 xxxxxxxxxxxxxxxx ADCMP3HI B56 0000000000000000 ADCMP0CON BA0 0000000000000000 ADIEH B22 -----------xxxxx ADFL0DAT B68 0000000000000000 ADCMP1CON BA4 0000000000000000 ADCSS1L B28 0000000000000000 ADFL0CON B6A 0xx0000000000000 ADCMP2CON BA8 0000000000000000 ADSTATL B30 0000000000000000 ADFL1DAT B6C 0000000000000000 ADCMP3CON BAC 0000000000000000 ADSTATH B32 -----------00000 ADFL1CON B6E 0xx0000000000000 ADLVLTRGL BD0 0000000000000000 ADCMP0ENL B38 0000000000000000 ADFL2DAT B70 0000000000000000 ADLVLTRGH BD2 -----------xxxxx ADC ADCMP0ENH B3A -----------00000 ADFL2CON B72 0xx0000000000000 ADEIEL BF0 xxxxxxxxxxxxxxxx ADCMP0LO B3C 0000000000000000 ADFL3DAT B74 0000000000000000 ADEIEH BF2 -----------xxxxx ADCMP0HI B3E 0000000000000000 ADFL3CON B76 0xx0000000000000 ADEISTATL BF8 xxxxxxxxxxxxxxxx ADCMP1ENL B40 0000000000000000 ADTRIG0L B80 0000000000000000 ADEISTATH BFA -----------xxxxx Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively. TABLE 3-15: Register MASTER SFR BLOCK C00h Address All Resets Register Address ADC (Continued) All Resets Register Address All Resets 000-----0000-000 ADCBUF9 C1E 0000000000000000 DAC ADCON5L C00 0-------0------- ADCBUF10 C20 0000000000000000 DACCTRL1L C80 ADCON5H C02 0---xxxx0------- ADCBUF11 C22 0000000000000000 DACCTRL2L C84 ------0001010101 ADCAL1H C0A 00000-00-000---- ADCBUF12 C24 0000000000000000 DACCTRL2H C86 ------0010001010 ADCBUF0 C0C 0000000000000000 ADCBUF13 C26 0000000000000000 DAC1CONL C88 000--000x0000000 ADCBUF1 C0E 0000000000000000 ADCBUF14 C28 0000000000000000 DAC1CONH C8A ------0000000000 0000000000000000 ADCBUF2 C10 0000000000000000 ADCBUF15 C2A 0000000000000000 DAC1DATL C8C ADCBUF3 C12 0000000000000000 ADCBUF16 C2C 0000000000000000 DAC1DATH C8E 0000000000000000 ADCBUF4 C14 0000000000000000 ADCBUF17 C2E 0000000000000000 SLP1CONL C90 0000000000000000 ADCBUF5 C16 0000000000000000 ADCBUF18 C30 0000000000000000 SLP1CONH C92 0---000--------- ADCBUF6 C18 0000000000000000 ADCBUF19 C32 0000000000000000 SLP1DAT C94 0000000000000000 ADCBUF7 C1A 0000000000000000 ADCBUF20 C34 0000000000000000 VREGCON CFC 0---------000000 ADCBUF8 C1C 0000000000000000 Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively.  2017-2019 Microchip Technology Inc. DS70005319D-page 61 dsPIC33CH128MP508 FAMILY TABLE 3-16: Register MASTER SFR BLOCK D00h Address All Resets Address All Resets Register Address All Resets RPCON D00 ----0----------- RPINR19 D2A 1111111111111111 RPINR20 D2C 1111111111111111 RPOR4 D88 --000000--000000 RPOR5 D8A RPINR0 D04 11111111-------- RPINR21 D2E --000000--000000 1111111111111111 RPOR6 D8C RPINR1 D06 1111111111111111 RPINR22 --000000--000000 D30 1111111111111111 RPOR7 D8E RPINR2 D08 11111111-------- --000000--000000 RPINR23 D32 1111111111111111 RPOR8 D90 RPINR3 D0A --000000--000000 1111111111111111 RPINR26 D38 --------11111111 RPOR9 D92 RPINR4 --000000--000000 D0C 1111111111111111 RPINR30 D40 11111111-------- RPOR10 D94 --000000--000000 RPINR5 D0E 1111111111111111 RPINR37 D4E 11111111-------- RPOR11 D96 --000000--000000 RPINR6 D10 1111111111111111 RPINR38 D50 --------11111111 RPOR12 D98 --000000--000000 RPINR7 D12 1111111111111111 RPINR42 D58 1111111111111111 RPOR13 D9A --000000--000000 RPINR8 D14 1111111111111111 RPINR43 D5A 1111111111111111 RPOR14 D9C --000000--000000 RPINR9 D16 1111111111111111 RPINR44 D5C 1111111111111111 RPOR15 D9E --000000--000000 RPINR10 D18 1111111111111111 RPINR45 D5E 1111111111111111 RPOR16 DA0 --000000--000000 RPINR11 D1A 1111111111111111 RPINR46 D60 1111111111111111 RPOR17 DA2 --000000--000000 RPINR12 D1C 1111111111111111 RPINR47 D62 1111111111111111 RPOR18 DA4 --000000--000000 RPINR13 D1E 1111111111111111 RPOR0 D80 --000000--000000 RPOR19 DA6 --000000--000000 RPINR14 D20 1111111111111111 RPOR1 D82 --000000--000000 RPOR20 DA8 --000000--000000 RPINR15 D22 1111111111111111 RPOR2 D84 --000000--000000 RPOR21 DAA --000000--000000 RPINR18 D28 1111111111111111 RPOR3 D86 --000000--000000 RPOR22 DAC --000000--000000 I/O Ports Register Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively. TABLE 3-17: Register MASTER SFR BLOCK E00h Address All Resets I/O Ports (Continued) ANSELA Register Address All Resets Register Address All Resets CNCONB E2A 0---0----------- LATD E5A xxxxxxxxxxxxxxxx E00 -----------11111 CNEN0B E2C 0000000000000000 ODCD E5C 0000000000000000 TRISA E02 -----------11111 CNSTATB E2E 0000000000000000 CNPUD E5E 0000000000000000 PORTA E04 -----------xxxxx CNEN1B E30 0000000000000000 CNPDD E60 0000000000000000 LATA E06 -----------xxxxx CNFB E32 0000000000000000 CNCOND E62 0---0----------- ODCA E08 -----------00000 ANSELC E38 --------1---1111 CNEN0D E64 0000000000000000 CNPUA E0A -----------00000 TRISC E3A 1111111111111111 CNSTATD E66 0000000000000000 CNPDA E0C -----------00000 PORTC E3C xxxxxxxxxxxxxxxx CNEN1D E68 0000000000000000 CNCONA E0E 0---0----------- LATC E3E xxxxxxxxxxxxxxxx CNFD E6A 0000000000000000 CNEN0A E10 -----------00000 ODCC E40 0000000000000000 TRISE E72 1111111111111111 CNSTATA E12 -----------00000 CNPUC E42 0000000000000000 PORTE E74 xxxxxxxxxxxxxxxx CNEN1A E14 -----------00000 CNPDC E44 0000000000000000 LATE E76 xxxxxxxxxxxxxxxx CNFA E16 -----------00000 CNCONC E46 0---0----------- ODCE E78 0000000000000000 ANSELB E1C ------111---1111 CNEN0C E48 0000000000000000 CNPUE E7A 0000000000000000 TRISB E1E 1111111111111111 CNSTATC E4A 0000000000000000 CNPDE E7C 0000000000000000 PORTB E20 xxxxxxxxxxxxxxxx CNEN1C E4C 0000000000000000 CNCONE E7E 0---0----------- LATB E22 xxxxxxxxxxxxxxxx CNFC E4E 0000000000000000 CNEN0E E80 0000000000000000 ODCB E24 0000000000000000 ANSELD E54 -----1---------- CNSTATE E82 0000000000000000 CNPUB E26 0000000000000000 TRISD E56 1111111111111111 CNEN1E E84 0000000000000000 CNPDB E28 0000000000000000 PORTD E58 xxxxxxxxxxxxxxxx CNFE E86 0000000000000000 Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively. DS70005319D-page 62  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 3-18: Register MASTER SFR BLOCK F00h Address All Resets F80 00--x-0000000011 Reset RCON Oscillator Register Address All Resets Register PMD2 PMD3 Address All Resets FA6 --------00000000 FA8 --------0-----0- PCTRAPH FC2 --------00000000 FEXL FC4 PMD4 FAA xxxxxxxxxxxxxxxx ------------0--- FEXH FC6 --------xxxxxxxx OSCCON F84 -000-yyy0-0-0--0 PMD6 FAE --000000-------- DPCL FCE xxxxxxxxxxxxxxxx CLKDIV F86 00110000--000001 PMD7 FB0 -------x----0--- DPCH FD0 --------xxxxxxxx PLLFBD F88 ----000010010110 PMD8 FB2 ---00--0--xx000- APPO FD2 xxxxxxxxxxxxxxxx PLLDIV F8A ------00-011-001 WDT APPI FD4 xxxxxxxxxxxxxxxx OSCTUN F8C ----------000000 WDTCONL FB4 0--0000000000000 APPS FD6 -----------xxxxx ACLKCON1 F8E 00-----0--000001 WDTCONH FB6 0000000000000000 STROUTL FD8 xxxxxxxxxxxxxxxx APLLFBD1 F90 ----000010010110 REFOCONL FB8 0-000-00----0000 STROUTH FDA xxxxxxxxxxxxxxxx APLLDIV1 F92 ------00-011-001 REFOCONH FBA -000000000000000 STROVCNT FDC xxxxxxxxxxxxxxxx CANCLKCON F9A ----xxxx-xxxxxxx REFOTRIM FBE 000000000------- JDATAH FFA xxxxxxxxxxxxxxxx PCTRAPL FC0 0000000000000000 JDATAL FFC xxxxxxxxxxxxxxxx PMD PMD1 Legend: FA4 ----000-00000-00 x = unknown or indeterminate value; “-” =unimplemented bits; y = value set by Configuration bits. Address and Reset values are in hexadecimal and binary, respectively.  2017-2019 Microchip Technology Inc. DS70005319D-page 63 dsPIC33CH128MP508 FAMILY 3.2.5.1 Paged Memory Scheme The dsPIC33CH128MP508 architecture extends the available Data Space through a paging scheme, which allows the available Data Space to be accessed using MOV instructions in a linear fashion for pre- and post-modified Effective Addresses (EAs). The upper half of the base Data Space address is used in conjunction with the Data Space Read Page (DSRPAG) register to form the Program Space Visibility (PSV) address. The paged memory scheme provides access to multiple 32-Kbyte windows in the PSV memory. The Data Space Read Page (DSRPAG) register, in combination with the upper half of the Data Space address, can provide up to 8 Mbytes of PSV address space. The paged data memory space is shown in Figure 3-8. The Program Space (PS) can be accessed with a DSRPAG of 0x200 or greater. Only reads from PS are supported using the DSRPAG. The Data Space Read Page (DSRPAG) register is located in the SFR space. Construction of the PSV address is shown in Figure 3-7. When DSRPAG[9] = 1 and the base address bit, EA[15] = 1, the DSRPAG[8:0] bits are concatenated onto EA[14:0] to form the 24-bit PSV read address. FIGURE 3-7: PROGRAM SPACE VISIBILITY (PSV) READ ADDRESS GENERATION 16-Bit DS EA EA[15] = 0 (DSRPAG = don’t care) No EDS Access 0 Byte Select EA EA[15] DSRPAG[9] =1 1 EA Select DSRPAG Generate PSV Address 1 DSRPAG[8:0] 9 Bits 15 Bits 24-Bit PSV EA Byte Select Note: DS read access when DSRPAG = 0x000 will force an address error trap. DS70005319D-page 64  2017-2019 Microchip Technology Inc.  2017-2019 Microchip Technology Inc. FIGURE 3-8: PAGED DATA MEMORY SPACE Table Address Space (TBLPAG[7:0]) Program Space (Instruction & Data) DS_Addr[15:0] 0x0000 Program Memory (lsw – [15:0]) 0x00_0000 DS_Addr[14:0] 0x0000 DS_Addr[15:0] 0xFFFF (DSRPAG = 0x200) No Writes Allowed Local Data Space (TBLPAG = 0x00) lsw Using TBLRDL/TBLWTL, MSB Using TBLRDH/TBLWTH 0x7FFF SFR Registers 0x0FFF 0x1000 0x0000 Up to 16-Kbyte RAM 0x2FFF 0x3000 0x7FFF 0x8000 (DSRPAG = 0x2FF) No Writes Allowed 0x0000 0x7F_FFFF 0x7FFF 0x0000 0xFFFF (DSRPAG = 0x300) No Writes Allowed 0x7FFF PSV Program Memory (MSB) 32-Kbyte PSV Window 0xFFFF 0x0000 Program Memory (MSB – [23:16]) 0x00_0000 (DSRPAG = 0x3FF) No Writes Allowed 0x7FFF DS70005319D-page 65 0x7F_FFFF (TBLPAG = 0x7F) lsw Using TBLRDL/TBLWTL, MSB Using TBLRDH/TBLWTH dsPIC33CH128MP508 FAMILY PSV Program Memory (lsw) 0x0000 dsPIC33CH128MP508 FAMILY When a PSV page overflow or underflow occurs, EA[15] is cleared as a result of the register indirect EA calculation. An overflow or underflow of the EA in the PSV pages can occur at the page boundaries when: • The initial address, prior to modification, addresses the PSV page • The EA calculation uses Pre- or Post-Modified Register Indirect Addressing; however, this does not include Register Offset Addressing In general, when an overflow is detected, the DSRPAG register is incremented and the EA[15] bit is set to keep the base address within the PSV window. When an underflow is detected, the DSRPAG register is decremented and the EA[15] bit is set to keep the base TABLE 3-19: O, Read U, Read U, Read U, Read [++Wn] or [Wn++] [--Wn] or [Wn--] Legend: Note 1: 2: 3: 4: Exceptions to the operation described above arise when entering and exiting the boundaries of Page 0 and PSV spaces. Table 3-19 lists the effects of overflow and underflow scenarios at different boundaries. In the following cases, when overflow or underflow occurs, the EA[15] bit is set and the DSRPAG is not modified; therefore, the EA will wrap to the beginning of the current page: • Register Indirect with Register Offset Addressing • Modulo Addressing • Bit-Reversed Addressing OVERFLOW AND UNDERFLOW SCENARIOS AT PAGE 0 AND PSV SPACE BOUNDARIES(2,3,4) Before O/U, Operation R/W O, Read address within the PSV window. This creates a linear PSV address space, but only when using Register Indirect Addressing modes. DSRPAG DS EA[15] DSRPAG = 0x2FF 1 DSRPAG = 0x3FF After Page Description DSRPAG DS EA[15] Page Description PSV: Last lsw page DSRPAG = 0x300 1 PSV: First MSB page 1 PSV: Last MSB page DSRPAG = 0x3FF 0 See Note 1 DSRPAG = 0x001 1 PSV page DSRPAG = 0x001 0 See Note 1 DSRPAG = 0x200 1 PSV: First lsw page DSRPAG = 0x200 0 See Note 1 DSRPAG = 0x300 1 PSV: First MSB page DSRPAG = 0x2FF 1 PSV: Last lsw page O = Overflow, U = Underflow, R = Read, W = Write The Register Indirect Addressing now addresses a location in the base Data Space (0x0000-0x8000). An EDS access, with DSRPAG = 0x000, will generate an address error trap. Only reads from PS are supported using DSRPAG. Pseudolinear Addressing is not supported for large offsets. DS70005319D-page 66  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.2.5.2 Extended X Data Space The lower portion of the base address space range, between 0x0000 and 0x7FFF, is always accessible, regardless of the contents of the Data Space Read Page register. It is indirectly addressable through the register indirect instructions. It can be regarded as being located in the default EDS Page 0 (i.e., EDS address range of 0x000000 to 0x007FFF with the base address bit, EA[15] = 0, for this address range). However, Page 0 cannot be accessed through the upper 32 Kbytes, 0x8000 to 0xFFFF, of base Data Space in combination with DSRPAG = 0x00. Consequently, DSRPAG is initialized to 0x001 at Reset. Note 1: DSRPAG should not be used to access Page 0. An EDS access with DSRPAG set to 0x000 will generate an address error trap. When the PC is pushed onto the stack, PC[15:0] are pushed onto the first available stack word, then PC[22:16] are pushed into the second available stack location. For a PC push during any CALL instruction, the MSB of the PC is zero-extended before the push, as shown in Figure 3-9. During exception processing, the MSB of the PC is concatenated with the lower eight bits of the CPU STATUS Register, SR. This allows the contents of SRL to be preserved automatically during interrupt processing. Note 1: To maintain system Stack Pointer (W15) coherency, W15 is never subject to (EDS) paging, and is therefore, restricted to an address range of 0x0000 to 0xFFFF. The same applies to the W14 when used as a Stack Frame Pointer (SFA = 1). 2: As the stack can be placed in, and can access X and Y spaces, care must be taken regarding its use, particularly with regard to local automatic variables in a C development environment 2: Clearing the DSRPAG in software has no effect. 3.2.5.3 Software Stack The W15 register serves as a dedicated Software Stack Pointer (SSP), and is automatically modified by exception processing, subroutine calls and returns; however, W15 can be referenced by any instruction in the same manner as all other W registers. This simplifies reading, writing and manipulating the Stack Pointer (for example, creating stack frames). Note: To protect against misaligned stack accesses, W15[0] is fixed to ‘0’ by the hardware. FIGURE 3-9: 0x0000 CALL STACK FRAME 15 0 CALL SUBR Stack Grows Toward Higher Address The remaining PSV pages are only accessible using the DSRPAG register in combination with the upper 32 Kbytes, 0x8000 to 0xFFFF, of the base address, where the base address bit, EA[15] = 1. PC[15:1] W15 (before CALL) b‘000000000’ PC[22:16] [Free Word] W15 (after CALL) W15 is initialized to 0x1000 during all Resets. This address ensures that the SSP points to valid RAM in all dsPIC33CH128MP508 devices and permits stack availability for non-maskable trap exceptions. These can occur before the SSP is initialized by the user software. You can reprogram the SSP during initialization to any location within Data Space. The Software Stack Pointer always points to the first available free word and fills the software stack, working from lower toward higher addresses. Figure 3-9 illustrates how it pre-decrements for a stack pop (read) and post-increments for a stack push (writes).  2017-2019 Microchip Technology Inc. DS70005319D-page 67 dsPIC33CH128MP508 FAMILY 3.2.6 INSTRUCTION ADDRESSING MODES The addressing modes shown in Table 3-20 form the basis of the addressing modes optimized to support the specific features of individual instructions. The addressing modes provided in the MAC class of instructions differ from those in the other instruction types. 3.2.6.1 File Register Instructions Most file register instructions use a 13-bit address field (f) to directly address data present in the first 8192 bytes of data memory (Near Data Space). Most file register instructions employ a Working register, W0, which is denoted as WREG in these instructions. The destination is typically either the same file register or WREG (with the exception of the MUL instruction), which writes the result to a register or register pair. The MOV instruction allows additional flexibility and can access the entire Data Space. TABLE 3-20: 3.2.6.2 MCU Instructions The three-operand MCU instructions are of the form: Operand 3 = Operand 1 Operand 2 where Operand 1 is always a Working register (that is, the addressing mode can only be Register Direct), which is referred to as Wb. Operand 2 can be a W register fetched from data memory or a 5-bit literal. The result location can either be a W register or a data memory location. The following addressing modes are supported by MCU instructions: • • • • • Register Direct Register Indirect Register Indirect Post-Modified Register Indirect Pre-Modified 5-Bit or 10-Bit Literal Note: Not all instructions support all the addressing modes given above. Individual instructions can support different subsets of these addressing modes. FUNDAMENTAL ADDRESSING MODES SUPPORTED Addressing Mode Description File Register Direct The address of the file register is specified explicitly. Register Direct The contents of a register are accessed directly. Register Indirect The contents of Wn form the Effective Address (EA). Register Indirect Post-Modified The contents of Wn form the EA. Wn is post-modified (incremented or decremented) by a constant value. Register Indirect Pre-Modified Wn is pre-modified (incremented or decremented) by a signed constant value to form the EA. Register Indirect with Register Offset The sum of Wn and Wb forms the EA. (Register Indexed) Register Indirect with Literal Offset DS70005319D-page 68 The sum of Wn and a literal forms the EA.  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.2.6.3 Move and Accumulator Instructions Move instructions, and the DSP accumulator class of instructions, provide a greater degree of addressing flexibility than other instructions. In addition to the addressing modes supported by most MCU instructions, move and accumulator instructions also support Register Indirect with Register Offset Addressing mode, also referred to as Register Indexed mode. Note: For the MOV instructions, the addressing mode specified in the instruction can differ for the source and destination EA. However, the 4-bit Wb (Register Offset) field is shared by both source and destination (but typically only used by one). 3.2.6.4 The dual source operand DSP instructions (CLR, ED, EDAC, MAC, MPY, MPY.N, MOVSAC and MSC), also referred to as MAC instructions, use a simplified set of addressing modes to allow the user application to effectively manipulate the Data Pointers through register indirect tables. The two-source operand prefetch registers must be members of the set {W8, W9, W10, W11}. For data reads, W8 and W9 are always directed to the X RAGU, and W10 and W11 are always directed to the Y AGU. The Effective Addresses generated (before and after modification) must therefore, be valid addresses within X Data Space for W8 and W9, and Y Data Space for W10 and W11. In summary, the following addressing modes are supported by move and accumulator instructions: • • • • • • • • Register Direct Register Indirect Register Indirect Post-Modified Register Indirect Pre-Modified Register Indirect with Register Offset (Indexed) Register Indirect with Literal Offset 8-Bit Literal 16-Bit Literal Note: Not all instructions support all the addressing modes given above. Individual instructions may support different subsets of these addressing modes.  2017-2019 Microchip Technology Inc. MAC Instructions Note: Register Indirect with Register Offset Addressing mode is available only for W9 (in X space) and W11 (in Y space). In summary, the following addressing modes are supported by the MAC class of instructions: • • • • • Register Indirect Register Indirect Post-Modified by 2 Register Indirect Post-Modified by 4 Register Indirect Post-Modified by 6 Register Indirect with Register Offset (Indexed) 3.2.6.5 Other Instructions Besides the addressing modes outlined previously, some instructions use literal constants of various sizes. For example, BRA (branch) instructions use 16-bit signed literals to specify the branch destination directly, whereas the DISI instruction uses a 14-bit unsigned literal field. In some instructions, such as ULNK, the source of an operand or result is implied by the opcode itself. Certain operations, such as a NOP, do not have any operands. DS70005319D-page 69 dsPIC33CH128MP508 FAMILY 3.2.7 MODULO ADDRESSING 3.2.7.1 Modulo Addressing mode is a method of providing an automated means to support circular data buffers using hardware. The objective is to remove the need for software to perform data address boundary checks when executing tightly looped code, as is typical in many DSP algorithms. Start and End Address The Modulo Addressing scheme requires that a starting and ending address be specified and loaded into the 16-bit Modulo Buffer Address registers: XMODSRT, XMODEND, YMODSRT and YMODEND (see Table 3-4). Note: Y space Modulo Addressing EA calculations assume word-sized data (LSb of every EA is always clear). Modulo Addressing can operate in either Data or Program Space (since the Data Pointer mechanism is essentially the same for both). One circular buffer can be supported in each of the X (which also provides the pointers into Program Space) and Y Data Spaces. Modulo Addressing can operate on any W Register Pointer. However, it is not advisable to use W14 or W15 for Modulo Addressing since these two registers are used as the Stack Frame Pointer and Stack Pointer, respectively. The length of a circular buffer is not directly specified. It is determined by the difference between the corresponding start and end addresses. The maximum possible length of the circular buffer is 32K words (64 Kbytes). In general, any particular circular buffer can be configured to operate in only one direction, as there are certain restrictions on the buffer start address (for incrementing buffers) or end address (for decrementing buffers), based upon the direction of the buffer. The Modulo and Bit-Reversed Addressing Control register, MODCON[15:0], contains enable flags, as well as a W register field to specify the W Address registers. The XWM and YWM fields select the registers that operate with Modulo Addressing: The only exception to the usage restrictions is for buffers that have a power-of-two length. As these buffers satisfy the start and end address criteria, they can operate in a Bidirectional mode (that is, address boundary checks are performed on both the lower and upper address boundaries). • If XWM = 1111, X RAGU and X WAGU Modulo Addressing is disabled • If YWM = 1111, Y AGU Modulo Addressing is disabled 3.2.7.2 W Address Register Selection The X Address Space Pointer W (XWM) register, to which Modulo Addressing is to be applied, is stored in MODCON[3:0] (see Table 3.2.1). Modulo Addressing is enabled for X Data Space when XWM is set to any value other than ‘1111’ and the XMODEN bit is set (MODCON[15]). The Y Address Space Pointer W (YWM) register, to which Modulo Addressing is to be applied, is stored in MODCON[7:4]. Modulo Addressing is enabled for Y Data Space when YWM is set to any value other than ‘1111’ and the YMODEN bit (MODCON[14]) is set. FIGURE 3-10: MODULO ADDRESSING OPERATION EXAMPLE Byte Address 0x1100 0x1163 Start Addr = 0x1100 End Addr = 0x1163 Length = 0x0032 words DS70005319D-page 70 MOV MOV MOV MOV MOV MOV #0x1100, W0 W0, XMODSRT #0x1163, W0 W0, MODEND #0x8001, W0 W0, MODCON MOV #0x0000, W0 ;W0 holds buffer fill value MOV #0x1110, W1 ;point W1 to buffer DO AGAIN, #0x31 MOV W0, [W1++] AGAIN: INC W0, W0 ;set modulo start address ;set modulo end address ;enable W1, X AGU for modulo ;fill the 50 buffer locations ;fill the next location ;increment the fill value  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.2.7.3 Modulo Addressing Applicability Modulo Addressing can be applied to the Effective Address (EA) calculation associated with any W register. Address boundaries check for addresses equal to: • The upper boundary addresses for incrementing buffers • The lower boundary addresses for decrementing buffers It is important to realize that the address boundaries check for addresses less than, or greater than, the upper (for incrementing buffers) and lower (for decrementing buffers) boundary addresses (not just equal to). Address changes can, therefore, jump beyond boundaries and still be adjusted correctly. Note: 3.2.8 The modulo corrected Effective Address is written back to the register only when Pre-Modify or Post-Modify Addressing mode is used to compute the Effective Address. When an address offset (such as [W7 + W2]) is used, Modulo Addressing correction is performed, but the contents of the register remain unchanged. BIT-REVERSED ADDRESSING Bit-Reversed Addressing mode is intended to simplify data reordering for radix-2 FFT algorithms. It is supported by the X AGU for data writes only. The modifier, which can be a constant value or register contents, is regarded as having its bit order reversed. The address source and destination are kept in normal order. Thus, the only operand requiring reversal is the modifier. 3.2.8.1 Bit-Reversed Addressing Implementation Bit-Reversed Addressing mode is enabled in any of these situations: • BWMx bits (W register selection) in the MODCON register are any value other than ‘1111’ (the stack cannot be accessed using Bit-Reversed Addressing) • The BREN bit is set in the XBREV register • The addressing mode used is Register Indirect with Pre-Increment or Post-Increment If the length of a bit-reversed buffer is M = 2N bytes, the last ‘N’ bits of the data buffer start address must be zeros. XB[14:0] is the Bit-Reversed Addressing modifier, or ‘pivot point’, which is typically a constant. In the case of an FFT computation, its value is equal to half of the FFT data buffer size. Note: All bit-reversed EA calculations assume word-sized data (LSb of every EA is always clear). The XB value is scaled accordingly to generate compatible (byte) addresses. When enabled, Bit-Reversed Addressing is executed only for Register Indirect with Pre-Increment or PostIncrement Addressing and word-sized data writes. It does not function for any other addressing mode or for byte-sized data and normal addresses are generated instead. When Bit-Reversed Addressing is active, the W Address Pointer is always added to the address modifier (XB) and the offset associated with the Register Indirect Addressing mode is ignored. In addition, as word-sized data are a requirement, the LSb of the EA is ignored (and always clear). Note: Modulo Addressing and Bit-Reversed Addressing can be enabled simultaneously using the same W register, but BitReversed Addressing operation will always take precedence for data writes when enabled. If Bit-Reversed Addressing has already been enabled by setting the BREN (XBREV[15]) bit, a write to the XBREV register should not be immediately followed by an indirect read operation using the W register that has been designated as the Bit-Reversed Pointer.  2017-2019 Microchip Technology Inc. DS70005319D-page 71 dsPIC33CH128MP508 FAMILY FIGURE 3-11: BIT-REVERSED ADDRESSING EXAMPLE Sequential Address b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 0 Bit Locations Swapped Left-to-Right Around Center of Binary Value b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b1 b2 b3 b4 0 Bit-Reversed Address Pivot Point TABLE 3-21: XB = 0x0008 for a 16-Word Bit-Reversed Buffer BIT-REVERSED ADDRESSING SEQUENCE (16-ENTRY) Normal Address Bit-Reversed Address A3 A2 A1 A0 Decimal A3 A2 A1 A0 Decimal 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 8 0 0 1 0 2 0 1 0 0 4 0 0 1 1 3 1 1 0 0 12 0 1 0 0 4 0 0 1 0 2 0 1 0 1 5 1 0 1 0 10 0 1 1 0 6 0 1 1 0 6 0 1 1 1 7 1 1 1 0 14 1 0 0 0 8 0 0 0 1 1 1 0 0 1 9 1 0 0 1 9 1 0 1 0 10 0 1 0 1 5 1 0 1 1 11 1 1 0 1 13 1 1 0 0 12 0 0 1 1 3 1 1 0 1 13 1 0 1 1 11 1 1 1 0 14 0 1 1 1 7 1 1 1 1 15 1 1 1 1 15 DS70005319D-page 72  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.2.9 INTERFACING PROGRAM AND DATA MEMORY SPACES Table instructions allow an application to read or write to small areas of the program memory. This capability makes the method ideal for accessing data tables that need to be updated periodically. It also allows access to all bytes of the program word. The remapping method allows an application to access a large block of data on a read-only basis, which is ideal for look-ups from a large table of static data. The application can only access the least significant word of the program word. The dsPIC33CH128MP508 family architecture uses a 24-bit wide Program Space (PS) and a 16-bit wide Data Space (DS). The architecture is also a modified Harvard scheme, meaning that data can also be present in the Program Space. To use these data successfully, they must be accessed in a way that preserves the alignment of information in both spaces. Aside from normal execution, the architecture of the dsPIC33CH128MP508 family devices provides two methods by which Program Space can be accessed during operation: • Using table instructions to access individual bytes or words anywhere in the Program Space • Remapping a portion of the Program Space into the Data Space (Program Space Visibility) TABLE 3-22: PROGRAM SPACE ADDRESS CONSTRUCTION Program Space Address Access Space Access Type [23] [22:16] Instruction Access (Code Execution) User TBLRD/TBLWT (Byte/Word Read/Write) User TBLPAG[7:0] Configuration TBLPAG[7:0] [15] 0xxx xxxx xxxx 0xxx xxxx [0] xxxx 0 xxxx xxx0 Data EA[15:0] xxxx xxxx xxxx xxxx 1xxx xxxx FIGURE 3-12: [14:1] PC[22:1] 0 Data EA[15:0] xxxx xxxx xxxx xxxx DATA ACCESS FROM PROGRAM SPACE ADDRESS GENERATION Program Counter(1) Program Counter 0 0 23 Bits EA Table Operations(2) 1/0 1/0 TBLPAG 8 Bits 16 Bits 24 Bits User/Configuration Space Select Note 1: 2: Byte Select The Least Significant bit (LSb) of Program Space addresses is always fixed as ‘0’ to maintain word alignment of data in the Program and Data Spaces. Table operations are not required to be word-aligned. Table Read operations are permitted in the configuration memory space.  2017-2019 Microchip Technology Inc. DS70005319D-page 73 dsPIC33CH128MP508 FAMILY 3.2.9.1 Data Access from Program Memory Using Table Instructions The TBLRDL and TBLWTL instructions offer a direct method of reading or writing the lower word of any address within the Program Space without going through Data Space. The TBLRDH and TBLWTH instructions are the only method to read or write the upper eight bits of a Program Space word as data. The PC is incremented by two for each successive 24-bit program word. This allows program memory addresses to directly map to Data Space addresses. Program memory can thus be regarded as two 16-bit wide word address spaces, residing side by side, each with the same address range. TBLRDL and TBLWTL access the space that contains the least significant data word. TBLRDH and TBLWTH access the space that contains the upper data byte. Two table instructions are provided to move byte or word-sized (16-bit) data to and from Program Space. Both function as either byte or word operations. • TBLRDL (Table Read Low): - In Word mode, this instruction maps the lower word of the Program Space location (P[15:0]) to a data address (D[15:0]) - In Byte mode, either the upper or lower byte of the lower program word is mapped to the lower byte of a data address. The upper byte is selected when Byte Select is ‘1’; the lower byte is selected when it is ‘0’. FIGURE 3-13: • TBLRDH (Table Read High): - In Word mode, this instruction maps the entire upper word of a program address (P[23:16]) to a data address. The ‘phantom’ byte (D[15:8]) is always ‘0’. - In Byte mode, this instruction maps the upper or lower byte of the program word to D[7:0] of the data address in the TBLRDL instruction. The data are always ‘0’ when the upper ‘phantom’ byte is selected (Byte Select = 1). In a similar fashion, two table instructions, TBLWTH and TBLWTL, are used to write individual bytes or words to a Program Space address. The details of their operation are explained in Section 3.3 “Master Flash Program Memory”. For all table operations, the area of program memory space to be accessed is determined by the Table Page register (TBLPAG). TBLPAG covers the entire program memory space of the device, including user application and configuration spaces. When TBLPAG[7] = 0, the table page is located in the user memory space. When TBLPAG[7] = 1, the page is located in configuration space. ACCESSING PROGRAM MEMORY WITH TABLE INSTRUCTIONS Program Space TBLPAG 02 23 15 0 0x000000 23 16 8 0 00000000 0x020000 0x030000 00000000 00000000 00000000 ‘Phantom’ Byte TBLRDH.B (Wn[0] = 0) TBLRDL.B (Wn[0] = 1) TBLRDL.B (Wn[0] = 0) TBLRDL.W 0x800000 DS70005319D-page 74 The address for the table operation is determined by the data EA within the page defined by the TBLPAG register. Only read operations are shown; write operations are also valid in the user memory area.  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.3 Master Flash Program Memory Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “Flash Programming” (www.microchip.com/DS70000609) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). 2: This section refers to the “Dual Partition Flash Program Memory” (www.microchip.com/DS70005156) in the “dsPIC33/PIC24 Family Reference Manual”, but the Dual Partition is not implemented in the Master Flash. The dsPIC33CH128MP508 family devices contain internal Flash program memory for storing and executing application code. The memory is readable, writable and erasable during normal operation over the entire VDD range. Flash memory can be programmed in three ways: • In-Circuit Serial Programming™ (ICSP™) programming capability • Enhanced In-Circuit Serial Programming (Enhanced ICSP) • Run-Time Self-Programming (RTSP) ICSP allows for a dsPIC33CH128MP508 family device to be serially programmed while in the end application circuit. This is done with a Programming Clock and Programming Data (PGCx/PGDx) line, and three other lines for power (VDD), ground (VSS) and Master Clear (MCLR). This allows customers to manufacture boards with unprogrammed devices and then program the device just before shipping the product. This also allows the most recent firmware or a custom firmware to be programmed. RTSP allows the Master Flash user application code to update itself during run time. The feature is capable of writing a single program memory word (two instructions) or an entire row as needed. 3.3.1 FLASH PROGRAMMING OPERATIONS For ICSP and RTSP programming of the Master Flash, TBLWTL and TBLWTH instructions are used to write to the NVM write latches. An NVM write operation then writes the contents of both latches to the Flash, starting at the address defined by the contents of TBLPAG, and the NVMADR and NVMADRU registers. Programmers can program two adjacent words (24 bits x 2) of Program Flash Memory at a time on every other word address boundary (0x000002, 0x000006, 0x00000A, etc.). To do this, it is necessary to erase the page that contains the desired address of the location the user wants to change. For protection against accidental operations, the write initiate sequence for NVMKEY must be used to allow any erase or program operation to proceed. After the programming command has been executed, the user application must wait for the programming time until programming is complete. Regardless of the method used to program the Flash, a few basic requirements should be met: • A full 48-bit double instruction word should always be programmed to a Flash location. Either instruction may simply be a NOP to fulfill this requirement. This ensures a valid ECC value is generated for each pair of instructions written. • Assuming the above step is followed, the last 24-bit location in implemented program space should never be executed. The penultimate instruction must contain a program flow change instruction, such as a RETURN or BRA instruction. Enhanced In-Circuit Serial Programming uses an on-board bootloader, known as the Program Executive, to manage the programming process. Using an SPI data frame format, the Program Executive can erase, program and verify program memory. For more information on Enhanced ICSP, see the device programming specification.  2017-2019 Microchip Technology Inc. DS70005319D-page 75 dsPIC33CH128MP508 FAMILY FIGURE 3-14: ADDRESSING FOR TABLE REGISTERS 24 Bits Using Program Counter Program Counter 0 0 Working Reg EA Using Table Instruction 1/0 TBLPAG Reg 8 Bits User/Configuration Space Select DS70005319D-page 76 16 Bits 24-Bit EA Byte Select  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.3.2 RTSP OPERATION RTSP allows the user application to program one double instruction word or one row at a time.The double instruction word write blocks and single row write blocks are edge-aligned, from the beginning of program memory, on boundaries of one double instruction word and 64 double instruction words, respectively. The basic sequence for RTSP programming is to first load two 24-bit instructions into the NVM write latches found in configuration memory space. Refer to Figure 3-3 EXAMPLE 3-1: through Figure 3-4 for write latch addresses. Then, the WR bit in the NVMCON register is set to initiate the write process. The processor stalls (waits) until the programming operation is finished. The WR bit is automatically cleared when the operation is finished. Double instruction word writes are performed by manually loading both write latches, using TBLWTL and TBLWTH instructions, and then initiating the NVM write while the NVMOPx bits are set to ‘0x1’. The program space destination address is defined by the NVMADR/U registers. FLASH WRITE/READ /////////Flash write //////////////////////// //Sample code for writing 0x123456 to address locations 0x10000 / 10002 NVMCON = 0x4001; TBLPAG = 0xFA; // write latch upper address NVMADR = 0x0000; // set target write address of general segment NVMADRU = 0x0001; __builtin_tblwtl(0, 0x3456); // load write latches __builtin_tblwth (0,0x12); __builtin_tblwtl(2, 0x3456); __builtin_tblwth (2,0x12); // load write latches asm volatile ("disi #5"); __builtin_write_NVM(); while(_WR == 1 ) ; ////////////Flash Read/////////////// //Sample code to read the Flash content of address 0x10000 // readDataL/ readDataH variables need to defined TBLPAG = 0x0001; readDataL = __builtin_tblrdl(0x0000); readDataH = __builtin_tblrdh(0x0000);  2017-2019 Microchip Technology Inc. DS70005319D-page 77 dsPIC33CH128MP508 FAMILY Row programming is performed by first loading 128 instructions into data RAM and then loading the address of the first instruction in that row into the NVMSRCADRL/H registers. Once the write has been initiated, the device will automatically load two instructions into the write latches and write them to the program space destination address defined by the NVMADR/U registers. The operation will increment the NVMSRCADRL/H and the NVMADR/U registers until all double instruction words have been programmed. The RPDF bit (NVMCON[9]) selects the format of the stored data in RAM to be either compressed or uncompressed. See Figure 3-15 for data formatting. Compressed data help to reduce the amount of required RAM by using the upper byte of the second word for the MSB of the second instruction. All erase and program operations may optionally use the NVM interrupt to signal the successful completion of the operation. FIGURE 3-15: UNCOMPRESSED/ COMPRESSED FORMAT 15 0 7 Increasing Address LSW1 0x00 Even Byte Address MSB1 LSW2 0x00 MSB2 UNCOMPRESSED FORMAT (RPDF = 0) Increasing Address 15 0 7 LSW1 MSB2 Even Byte Address MSB1 LSW2 COMPRESSED FORMAT (RPDF = 1) DS70005319D-page 78 3.3.3 ERROR CORRECTING CODE (ECC) In order to improve program memory performance and durability, the devices include Error Correcting Code functionality (ECC) as an integral part of the Flash memory controller. ECC can determine the presence of single bit errors in program data, including which bit is in error, and correct the data automatically without user intervention. ECC cannot be disabled. When data are written to program memory, ECC generates a 7-bit Hamming code parity value for every two (24-bit) instruction words. The data are stored in blocks of 48 data bits and seven parity bits; parity data are not memory-mapped and are inaccessible. When the data are read back, the ECC calculates the parity on it and compares it to the previously stored parity value. If a parity mismatch occurs, there are two possible outcomes: • Single bit error has occurred and has been automatically corrected on readback. • Double-bit error has occurred and the read data are not changed. Single bit error occurrence can be identified by the state of the ECCSBEIF (IFS0[13]) bit. An interrupt can be generated when the corresponding interrupt enable bit is set, ECCSBEIE (IEC0[13]). The ECCSTATL register contains the parity information for single bit errors. The SECOUT[7:0] bit field contains the expected calculated SEC parity and SECIN[7:0] bits contain the actual value from a Flash read operation. The SECSYNDx bits (ECCSTATH[7:0]) indicate the bit position of the single bit error within the 48-bit pair of instruction words. When no error is present, SECINx equals SECOUTx and SECSYNDx is zero. Double-bit errors result in a generic hard trap. The ECCDBE bit (INTCON4[1]) will be set to identify the source of the hard trap. If no Interrupt Service Routine is implemented for the hard trap, a device Reset will also occur. The ECCSTATH register contains double-bit error status information. The DEDOUT bit is the expected calculated DED parity and DEDIN is the actual value from a Flash read operation. When no error is present, DEDIN equals DEDOUT.  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.3.3.1 ECC Fault Injection To test Fault handling, an EEC error can be generated. Both single and double-bit errors can be generated in both the read and write data paths. Read path Fault injection first reads the Flash data and then modifies them prior to entering the ECC logic. Write path Fault injection modifies the actual data prior to them being written into the target Flash and will cause an EEC error on subsequent Flash read. The following procedure is used to inject a Fault: 1. 2. 3. 4. 5. 6. Load Flash target address into the ECCADDR register. Select 1st Fault bit determined by FLT1PTRx (ECCCONH[7:0]). The target bit is inverted to create the Fault. If a double Fault is desired, select the 2nd Fault bit determined by FLT2PTRx (ECCCONH[15:8]), otherwise set to all ‘1’s. Write the NVMKEY unlock sequence. Enable the ECC Fault injection logic by setting the FLTINJ bit (ECCCONL[0]) Perform a read or write to the Flash target address.  2017-2019 Microchip Technology Inc. 3.3.4 CONTROL REGISTERS Five SFRs are used to write and erase the Program Flash Memory: NVMCON, NVMKEY, NVMADR, NVMADRU and NVMSRCADRL/H. The NVMCON register (Register 3-4) selects the operation to be performed (page erase, word/row program, Inactive Partition erase) and initiates the program or erase cycle. NVMKEY (Register 3-7) is a write-only register that is used for write protection. To start a programming or erase sequence, the user application must consecutively write 0x55 and 0xAA to the NVMKEY register. There are two NVM Address registers: NVMADR and NVMADRU. These two registers, when concatenated, form the 24-bit Effective Address (EA) of the selected word/row for programming operations, or the selected page for erase operations. The NVMADRU register is used to hold the upper eight bits of the EA, while the NVMADR register is used to hold the lower 16 bits of the EA. For row programming operation, data to be written to Program Flash Memory are written into data memory space (RAM) at an address defined by the NVMSRCADRL/H register (location of first element in row programming data). DS70005319D-page 79 dsPIC33CH128MP508 FAMILY 3.3.5 NVM CONTROL REGISTERS REGISTER 3-4: R/SO-0(1) NVMCON: NONVOLATILE MEMORY (NVM) CONTROL REGISTER R/W-0(1) WR WREN R/W-0(1) R/W-0 U-0 U-0 R/W-0 R/C-0 WRERR NVMSIDL(2) — — RPDF URERR bit 15 bit 8 U-0 U-0 U-0 U-0 — — — — R/W-0(1) R/W-0(1) R/W-0(1) R/W-0(1) NVMOP[3:0](3,4) bit 7 bit 0 Legend: C = Clearable bit SO = Settable Only bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 WR: Write Control bit(1) 1 = Initiates a Flash memory program or erase operation; the operation is self-timed and the bit is cleared by hardware once the operation is complete 0 = Program or erase operation is complete and inactive bit 14 WREN: Write Enable bit(1) 1 = Enables Flash program/erase operations 0 = Inhibits Flash program/erase operations bit 13 WRERR: Write Sequence Error Flag bit(1) 1 = An improper program or erase sequence attempt, or termination has occurred (bit is set automatically on any set attempt of the WR bit) 0 = The program or erase operation completed normally bit 12 NVMSIDL: NVM Stop in Idle Control bit(2) 1 = Flash voltage regulator goes into Standby mode during Idle mode 0 = Flash voltage regulator is active during Idle mode bit 11-10 Unimplemented: Read as ‘0’ bit 9 RPDF: Row Programming Data Format bit 1 = Row data to be stored in RAM are in compressed format 0 = Row data to be stored in RAM are in uncompressed format bit 8 URERR: Row Programming Data Underrun Error bit 1 = Indicates row programming operation has been terminated 0 = No data underrun error is detected bit 7-4 Unimplemented: Read as ‘0’ Note 1: 2: 3: 4: 5: These bits can only be reset on a POR. If this bit is set, there will be minimal power savings (IIDLE), and upon exiting Idle mode, there is a delay (TVREG) before Flash memory becomes operational. All other combinations of NVMOP[3:0] are unimplemented. Execution of the PWRSAV instruction is ignored while any of the NVM operations are in progress. Two adjacent words on a 4-word boundary are programmed during execution of this operation. DS70005319D-page 80  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-4: NVMCON: NONVOLATILE MEMORY (NVM) CONTROL REGISTER (CONTINUED) NVMOP[3:0]: NVM Operation Select bits(1,3,4) 1111 = Reserved 1110 = User memory bulk erase operation 1101 = Reserved 1100 = Reserved 1011 = Reserved 1010 = Reserved 1001 = Reserved 1000 = Reserved 0111 = Reserved 0101 = Reserved 0100 = Reserved 0011 = Memory page erase operation 0010 = Memory row program operation 0001 = Memory double-word operation(5) 0000 = Reserved bit 3-0 Note 1: 2: 3: 4: 5: These bits can only be reset on a POR. If this bit is set, there will be minimal power savings (IIDLE), and upon exiting Idle mode, there is a delay (TVREG) before Flash memory becomes operational. All other combinations of NVMOP[3:0] are unimplemented. Execution of the PWRSAV instruction is ignored while any of the NVM operations are in progress. Two adjacent words on a 4-word boundary are programmed during execution of this operation.  2017-2019 Microchip Technology Inc. DS70005319D-page 81 dsPIC33CH128MP508 FAMILY REGISTER 3-5: R/W-x NVMADR: NONVOLATILE MEMORY LOWER ADDRESS REGISTER R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x NVMADR[15:8] bit 15 bit 8 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x NVMADR[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown NVMADR[15:0]: Nonvolatile Memory Lower Write Address bits Selects the lower 16 bits of the location to program or erase in Program Flash Memory. This register may be read or written to by the user application. REGISTER 3-6: NVMADRU: NONVOLATILE MEMORY UPPER ADDRESS REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x NVMADRU[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7-0 NVMADRU[23:16]: Nonvolatile Memory Upper Write Address bits Selects the upper eight bits of the location to program or erase in Program Flash Memory. This register may be read or written to by the user application. DS70005319D-page 82  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-7: NVMKEY: NONVOLATILE MEMORY KEY REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 NVMKEY[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-8 Unimplemented: Read as ‘0’ bit 7-0 NVMKEY[7:0]: NVM Key Register bits (write-only)  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 83 dsPIC33CH128MP508 FAMILY REGISTER 3-8: R/W-0 NVMSRCADRL: NVM SOURCE DATA ADDRESS REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 NVMSRCADR[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 NVMSRCADR[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown NVMSRCADR[15:0]: NVM Source Data Address bits The RAM address of the data to be programmed into Flash when the NVMOP[3:0] bits are set to row programming. REGISTER 3-9: NVMSRCADRH: NVM SOURCE DATA ADDRESS REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 NVMSRCADR[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7-0 NVMSRCADR[23:16]: NVM Source Data Address bits The RAM address of the data to be programmed into Flash when the NVMOP[3:0] bits are set to row programming. DS70005319D-page 84  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.3.6 ECC CONTROL REGISTERS REGISTER 3-10: ECCCONL: ECC FAULT INJECTION CONFIGURATION REGISTER LOW U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — — FLTINMJ bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-1 Unimplemented: Read as ‘0’ bit 0 FLTINJ: Fault Injection Sequence Enable bit 1 = Enabled 0 = Disabled REGISTER 3-11: R/W-0 x = Bit is unknown ECCCONH: ECC FAULT INJECTION CONFIGURATION REGISTER HIGH R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FLT2PTR[7:0] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FLT1PTR[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 FLT2PTR[7:0]: ECC Fault Injection Bit Pointer 2 11111111-00111000 = No Fault injection occurs 00110111 = Fault injection (bit inversion) occurs on bit 55 of ECC bit order ... 00000001 = Fault injection (bit inversion) occurs on bit 1 of ECC bit order 00000000 = Fault injection (bit inversion) occurs on bit 0 of ECC bit order bit 7-0 FLT1PTR[7:0]: ECC Fault Injection Bit Pointer 1 11111111-00111000 = No Fault injection occurs 00110111 = Fault injection occurs on bit 55 of ECC bit order ... 00000001 = Fault injection occurs on bit 1 of ECC bit order 00000000 = Fault injection occurs on bit 0 of ECC bit order  2017-2019 Microchip Technology Inc. DS70005319D-page 85 dsPIC33CH128MP508 FAMILY REGISTER 3-12: R/W-0 ECCADDRL: ECC FAULT INJECT ADDRESS COMPARE REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ECCADDR[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ECCADDR[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown ECCADDR[15:0]: ECC Fault Injection NVM Address Match Compare bits REGISTER 3-13: R/W-0 ECCADDRH: ECC FAULT INJECT ADDRESS COMPARE REGISTER HIGH R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ECCADDR[31:24] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ECCADDR[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown ECCADDR[31:16]: ECC Fault Injection NVM Address Match Compare bits DS70005319D-page 86  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-14: R-0 ECCSTATL: ECC SYSTEM STATUS DISPLAY REGISTER LOW R-0 R-0 R-0 R-0 R-0 R-0 R-0 SECOUT[7:0] bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 SECIN[7:0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 SECOUT[7:0]: Calculated Single Error Correction Parity Value bits bit 7-0 SECIN[7:0]: Read Single Error Correction Parity Value bits Bits are the actual parity value of a Flash read operation. REGISTER 3-15: ECCSTATH: ECC SYSTEM STATUS DISPLAY REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 R-0 R-0 — — — — — — DEDOUT DEDIN bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 SECSYND[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-10 Unimplemented: Read as ‘0’ bit 9 DEDOUT: Calculated Dual Bit Error Detection Parity bit bit 8 DEDIN: Read Dual Bit Error Detection Parity bit bit 7-0 SECSYND[7:0]: Calculated ECC Syndrome Value bits Indicates the bit location that contains the error.  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 87 dsPIC33CH128MP508 FAMILY 3.4 Master Resets Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “Reset” (www.microchip.com/ DS70602) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). The Reset module combines all Reset sources and controls the device Master Reset Signal, SYSRST. The following is a list of device Reset sources: • • • • • • • • POR: Power-on Reset BOR: Brown-out Reset MCLR: Master Clear Pin Reset SWR: RESET Instruction WDTO: Watchdog Timer Time-out Reset CM: Configuration Mismatch Reset TRAPR: Trap Conflict Reset IOPUWR: Illegal Condition Device Reset - Illegal Opcode Reset - Uninitialized W Register Reset - Security Reset Note: Refer to the specific peripheral section or Section 3.2 “Master Memory Organization” of this data sheet for register Reset states. All types of device Reset set a corresponding status bit in the RCON register to indicate the type of Reset (see Register 3-16). A POR clears all the bits, except for the BOR and POR bits (RCON[1:0]) that are set. The user application can set or clear any bit, at any time, during code execution. The RCON bits only serve as status bits. Setting a particular Reset status bit in software does not cause a device Reset to occur. The RCON register also has other bits associated with the Watchdog Timer and device power-saving states. The function of these bits is discussed in other sections of this data sheet. Note: A simplified block diagram of the Reset module is shown in Figure 3-16. FIGURE 3-16: Any active source of Reset will make the SYSRST signal active. On system Reset, some of the registers associated with the CPU and peripherals are forced to a known Reset state, and some are unaffected. The status bits in the RCON register should be cleared after they are read so that the next RCON register value after a device Reset is meaningful. For all Resets, the default clock source is determined by the FNOSC[2:0] bits in the FOSCSEL Configuration register. The value of the FNOSCx bits is loaded into the NOSC[2:0] (OSCCON[10:8]) bits on Reset, which in turn, initializes the system clock. MASTER RESET SYSTEM BLOCK DIAGRAM RESET Instruction Glitch Filter MCLR WDT Module Sleep or Idle VDD BOR Internal Regulator SYSRST VDD Rise Detect POR Trap Conflict Illegal Opcode Uninitialized W Register Security Reset Configuration Mismatch DS70005319D-page 88  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.4.1 RESET RESOURCES Many useful resources are provided on the main product page of the Microchip website for the devices listed in this data sheet. This product page contains the latest updates and additional information.  2017-2019 Microchip Technology Inc. 3.4.1.1 Key Resources • “Reset” (www.microchip.com/DS70602) in the “dsPIC33/PIC24 Family Reference Manual” • Code Samples • Application Notes • Software Libraries • Webinars • All Related “dsPIC33/PIC24 Family Reference Manual” Sections • Development Tools DS70005319D-page 89 dsPIC33CH128MP508 FAMILY 3.4.2 RESET CONTROL REGISTER RCON: RESET CONTROL REGISTER(1) REGISTER 3-16: R/W-0 R/W-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 TRAPR IOPUWR — — — — CM VREGS bit 15 bit 8 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-1 R/W-1 EXTR SWR — WDTO SLEEP IDLE BOR POR bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 TRAPR: Trap Reset Flag bit 1 = A Trap Conflict Reset has occurred 0 = A Trap Conflict Reset has not occurred bit 14 IOPUWR: Illegal Opcode or Uninitialized W Register Access Reset Flag bit 1 = An illegal opcode detection, an illegal address mode or Uninitialized W register used as an Address Pointer caused a Reset 0 = An illegal opcode or Uninitialized W Register Reset has not occurred bit 13-10 Unimplemented: Read as ‘0’ bit 9 CM: Configuration Mismatch Flag bit 1 = A Configuration Mismatch Reset has occurred. 0 = A Configuration Mismatch Reset has not occurred bit 8 VREGS: Voltage Regulator Standby During Sleep bit 1 = Voltage regulator is active during Sleep 0 = Voltage regulator goes into Standby mode during Sleep bit 7 EXTR: External Reset (MCLR) Pin bit 1 = A Master Clear (pin) Reset has occurred 0 = A Master Clear (pin) Reset has not occurred bit 6 SWR: Software RESET (Instruction) Flag bit 1 = A RESET instruction has been executed 0 = A RESET instruction has not been executed bit 5 Unimplemented: Read as ‘0’ bit 4 WDTO: Watchdog Timer Time-out Flag bit 1 = WDT time-out has occurred 0 = WDT time-out has not occurred bit 3 SLEEP: Wake-up from Sleep Flag bit 1 = Device has been in Sleep mode 0 = Device has not been in Sleep mode bit 2 IDLE: Wake-up from Idle Flag bit 1 = Device has been in Idle mode 0 = Device has not been in Idle mode bit 1 BOR: Brown-out Reset Flag bit 1 = A Brown-out Reset has occurred 0 = A Brown-out Reset has not occurred Note 1: All of the Reset status bits can be set or cleared in software. Setting one of these bits in software does not cause a device Reset. DS70005319D-page 90  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-16: bit 0 Note 1: RCON: RESET CONTROL REGISTER(1) (CONTINUED) POR: Power-on Reset Flag bit 1 = A Power-on Reset has occurred 0 = A Power-on Reset has not occurred All of the Reset status bits can be set or cleared in software. Setting one of these bits in software does not cause a device Reset.  2017-2019 Microchip Technology Inc. DS70005319D-page 91 dsPIC33CH128MP508 FAMILY 3.5 Master Interrupt Controller Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “Interrupts” (www.microchip.com/ DS70000600) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). The dsPIC33CH128MP508 family interrupt controller reduces the numerous peripheral interrupt request signals to a single interrupt request signal to the dsPIC33CH128MP508 family CPU. 3.5.1.1 The Alternate Interrupt Vector Table (AIVT), shown in Figure 3-18, is available only when the Boot Segment (BS) is defined and the AIVT has been enabled. To enable the Alternate Interrupt Vector Table, the Configuration bit, AIVTDIS in the FSEC register, must be programmed and the AIVTEN bit must be set (INTCON2[8] = 1). When the AIVT is enabled, all interrupt and exception processes use the alternate vectors instead of the default vectors. The AIVT begins at the start of the last page of the Boot Segment, defined by BSLIM[12:0]. The second half of the page is no longer usable space. The Boot Segment must be at least two pages to enable the AIVT. Note: The interrupt controller has the following features: • Six Processor Exceptions and Software Traps • Seven User-Selectable Priority Levels • Interrupt Vector Table (IVT) with a Unique Vector for each Interrupt or Exception Source • Fixed Priority within a Specified User Priority Level • Fixed Interrupt Entry and Return Latencies • Alternate Interrupt Vector Table (AIVT) for Debug Support 3.5.1 INTERRUPT VECTOR TABLE The dsPIC33CH128MP508 family Interrupt Vector Table (IVT), shown in Figure 3-17, resides in program memory, starting at location, 000004h. The IVT contains six non-maskable trap vectors and up to 246 sources of interrupts. In general, each interrupt source has its own vector. Each interrupt vector contains a 24-bit wide address. The value programmed into each interrupt vector location is the starting address of the associated Interrupt Service Routine (ISR). Interrupt vectors are prioritized in terms of their natural priority. This priority is linked to their position in the vector table. Lower addresses generally have a higher natural priority. For example, the interrupt associated with Vector 0 takes priority over interrupts at any other vector address. DS70005319D-page 92 Alternate Interrupt Vector Table Although the Boot Segment must be enabled in order to enable the AIVT, application code does not need to be present inside of the Boot Segment. The AIVT (and IVT) will inherit the Boot Segment code protection. The AIVT supports debugging by providing a means to switch between an application and a support environment without requiring the interrupt vectors to be reprogrammed. This feature also enables switching between applications for evaluation of different software algorithms at run time. 3.5.2 RESET SEQUENCE A device Reset is not a true exception because the interrupt controller is not involved in the Reset process. The dsPIC33CH128MP508 family devices clear their registers in response to a Reset, which forces the PC to zero. The device then begins program execution at location, 0x000000. A GOTO instruction at the Reset address can redirect program execution to the appropriate start-up routine. Note: Any unimplemented or unused vector locations in the IVT should be programmed with the address of a default interrupt handler routine that contains a RESET instruction.  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY IVT Decreasing Natural Order Priority FIGURE 3-17: dsPIC33CH128MP508 FAMILY MASTER INTERRUPT VECTOR TABLE Reset – GOTO Instruction Reset – GOTO Address Oscillator Fail Trap Vector Address Error Trap Vector Generic Hard Trap Vector Stack Error Trap Vector Math Error Trap Vector Reserved Generic Soft Trap Vector Reserved Interrupt Vector 0 Interrupt Vector 1 : : : Interrupt Vector 52 Interrupt Vector 53 Interrupt Vector 54 : : : Interrupt Vector 116 Interrupt Vector 117 Interrupt Vector 118 Interrupt Vector 119 Interrupt Vector 120 : : : Interrupt Vector 244 Interrupt Vector 245 START OF CODE  2017-2019 Microchip Technology Inc. 0x000000 0x000002 0x000004 0x000006 0x000008 0x00000A 0x00000C 0x00000E 0x000010 0x000012 0x000014 0x000016 : : : 0x00007C 0x00007E 0x000080 : : : 0x0000FC 0x0000FE 0x000100 0x000102 0x000104 : : : 0x0001FC 0x0001FE 0x000200 See Table 3-19 for Interrupt Vector Details DS70005319D-page 93 dsPIC33CH128MP508 FAMILY FIGURE 3-18: dsPIC33CH128MP508 ALTERNATE MASTER INTERRUPT VECTOR TABLE AIVT Decreasing Natural Order Priority Reserved Reserved Oscillator Fail Trap Vector Address Error Trap Vector Generic Hard Trap Vector Stack Error Trap Vector Math Error Trap Vector Reserved Generic Soft Trap Vector Reserved Interrupt Vector 0 Interrupt Vector 1 : : : Interrupt Vector 52 Interrupt Vector 53 Interrupt Vector 54 : : : Interrupt Vector 116 Interrupt Vector 117 Interrupt Vector 118 Interrupt Vector 119 Interrupt Vector 120 : : : Interrupt Vector 244 Interrupt Vector 245 Note 1: BSLIM[12:0](1) + 0x000000 BSLIM[12:0](1) + 0x000002 BSLIM[12:0](1) + 0x000004 BSLIM[12:0](1) + 0x000006 BSLIM[12:0](1) + 0x000008 BSLIM[12:0](1) + 0x00000A BSLIM[12:0](1) + 0x00000C BSLIM[12:0](1) + 0x00000E BSLIM[12:0](1) + 0x000010 BSLIM[12:0](1) + 0x000012 BSLIM[12:0](1) + 0x000014 BSLIM[12:0](1) + 0x000016 : : : BSLIM[12:0](1) + 0x00007C BSLIM[12:0](1) + 0x00007E BSLIM[12:0](1) + 0x000080 : : : BSLIM[12:0](1) + 0x0000FC BSLIM[12:0](1) + 0x0000FE BSLIM[12:0](1) + 0x000100 BSLIM[12:0](1) + 0x000102 BSLIM[12:0](1) + 0x000104 : : : BSLIM[12:0](1) + 0x0001FC BSLIM[12:0](1) + 0x0001FE See Table 3-19 for Interrupt Vector Details The address depends on the size of the Boot Segment defined by BSLIM[12:0]: [(BSLIM[12:0] – 1) x 0x800] + Offset. DS70005319D-page 94  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 3-23: TRAP TABLE Trap Description MPLAB® XC16 Vector Trap ISR # Name IVT Address Trap Bit Location Generic Flag Source Flag Enable Priority Level Oscillator Failure Trap _OscillatorFail 0 0x000004 INTCON1[1] — — 15 Address Error Trap _AddressError 1 0x000006 INTCON1[3] — — 14 Generic Hard Trap – ECCDBE _HardTrapError 2 0x000008 — INTCON4[1] — 13 Generic Hard Trap – SGHT 2 0x000008 — INTCON4[0] INTCON2[13] 13 — 12 _HardTrapError — Stack Error Trap _StackError 3 0x00000A INTCON1[2] Math Error Trap – OVAERR _MathError 4 0x00000C INTCON1[4] INTCON1[14] INTCON1[10] 11 Math Error Trap – OVBERR _MathError 4 0x00000C INTCON1[4] INTCON1[13] INTCON1[9] 11 Math Error Trap – COVAERR _MathError 4 0x00000C INTCON1[4] INTCON1[12] INTCON1[8] 11 Math Error Trap – COVBERR _MathError 4 0x00000C INTCON1[4] INTCON1[11] INTCON1[8] 11 Math Error Trap – SFTACERR _MathError 4 0x00000C INTCON1[4] INTCON1[7] INTCON1[8] 11 Math Error Trap – DIV0ERR _MathError 4 0x00000C INTCON1[4] INTCON1[6] INTCON1[8] 11 Reserved Reserved 5 0x00000E — — — — Generic Soft Trap – CAN _SoftTrapError 6 0x000010 — INTCON3[9] — 9 Generic Soft Trap – NAE _SoftTrapError 6 0x000010 — INTCON3[8] — 9 Generic Soft Trap – CAN2 _SoftTrapError 6 0x000010 — INTCON3[6] — 9 Generic Soft Trap – DAE _SoftTrapError 6 0x000010 — INTCON3[5] — 9 Generic Soft Trap – DOOVR _SoftTrapError 6 0x000010 — INTCON3[4] — 9 Generic Soft Trap – APLL Lock _SoftTrapError 6 0x000010 — INTCON3[0] — 9 Reserved 7 0x000012 — — — — Reserved  2017-2019 Microchip Technology Inc. DS70005319D-page 95 dsPIC33CH128MP508 FAMILY TABLE 3-24: MASTER INTERRUPT VECTOR DETAILS(1) Interrupt Description MPLAB® XC16 ISR Name Vector # IRQ # IVT Address Interrupt Bit Location Flag Enable Priority External Interrupt 0 _INT0Interrupt 8 0 0x000014 IFS0[0] IEC0[0] IPC0[2:0] Timer1 _T1Interrupt 9 1 0x000016 IFS0[1] IEC0[1] IPC0[6:4] Change Notice Interrupt A _CNAInterrupt 10 2 0x000018 IFS0[2] IEC0[2] IPC0[10:8] Change Notice Interrupt B _CNBInterrupt 11 3 0x00001A IFS0[3] IEC0[3] IPC0[14:12] DMA Channel 0 _DMA0Interrupt 12 4 0x00001C IFS0[4] IEC0[4] IPC1[2:0] Reserved Reserved 13 5 0x00001E — — — Input Capture/Output Compare 1 _CCP1Interrupt 14 6 0x000020 IFS0[6] IEC0[6] IPC1[10:8] CCP1 Timer _CCT1Interrupt 15 7 0x000022 IFS0[7] IEC0[7] IPC1[14:12] DMA Channel 1 _DMA1Interrupt 16 8 0x000024 IFS0[8] IEC0[8] IPC2[2:0] SPI1 Receiver _SPI1RXInterrupt 17 9 0x000026 IFS0[9] IEC0[9] IPC2[6:4] SPI1 Transmitter _SPI1TXInterrupt 18 10 0x000028 IFS0[10] IEC0[10] IPC2[10:8] UART1 Receiver _U1RXInterrupt 19 11 0x00002A IFS0[11] IEC0[11] IPC2[14:12] UART1 Transmitter _U1TXInterrupt 20 12 0x00002C IFS0[12] IEC0[12] IPC3[2:0] ECC Single Bit Error _ECCSBEInterrupt 21 13 0x00002E IFS0[13] IEC0[13] IPC3[6:4] NVM Write Complete _NVMInterrupt 22 14 0x000030 IFS0[14] IEC0[14] IPC3[10:8] External Interrupt 1 _INT1Interrupt 23 15 0x000032 IFS0[15] IEC0[15] IPC3[14:12] I2C1 Slave Event _SI2C1Interrupt 24 16 0x000034 IFS1[0] IEC1[0] IPC4[2:0] I2C1 Master Event _MI2C1Interrupt 25 17 0x000036 IFS1[1] IEC1[1] IPC4[6:4] DMA Channel 2 _DMA2Interrupt 26 18 0x000038 IFS1[2] IEC1[2] IPC4[10:8] Change Notice Interrupt C _CNCInterrupt 27 19 0x00003A IFS1[3] IEC1[3] IPC4[14:12] External Interrupt 2 _INT2Interrupt 28 20 0x00003C IFS1[4] IEC1[4] IPC5[2:0] DMA Channel 3 _DMA3Interrupt 29 21 0x00003E IFS1[5] IEC1[5] IPC5[6:4] DMA Channel 4 _DMA4Interrupt 30 22 0x000040 IFS1[6] IEC1[6] IPC5[10:8] Input Capture/Output Compare 2 _CCP2Interrupt 31 23 0x000042 IFS1[7] IEC1[7] IPC5[14:12] CCP2 Timer _CCT2Interrupt 32 24 0x000044 IFS1[8] IEC1[8] IPC6[2:0] CAN1 Combined Error _CAN1Interrupt 33 25 0x000046 IFS1[9] IEC1[9] IPC6[6:4] External Interrupt 3 _INT3Interrupt 34 26 0x000048 IFS1[10] IEC1[10] IPC6[10:8] UART2 Receiver _U2RXInterrupt 35 27 0x00004A IFS1[11] IEC1[11] IPC6[14:12] UART2 Transmitter _U2TXInterrupt 36 28 0x00004C IFS1[12] IEC1[12] IPC7[2:0] SPI2 Receiver _SPI2RXInterrupt 37 29 0x00004E IFS1[13] IEC1[13] IPC7[6:4] SPI2 Transmitter _SPI2TXInterrupt 38 30 0x000050 IFS1[14] IEC1[14] IPC7[10:8] CAN1 RX Data Ready _C1RXInterrupt 39 31 0x000052 IFS1[15] IEC1[15] IPC7[14:12] Reserved Reserved 40-41 32-33 0x000054-0x000056 — — — DMA Channel 5 _DMA5Interrupt 42 34 0x000058 IFS2[2] IEC2[2] IPC8[10:8] Input Capture/Output Compare 3 _CCP3Interrupt 43 35 0x00005A IFS2[3] IEC2[3] IPC8[14:12] CCP3 Timer _CCT3Interrupt 44 36 0x00005C IFS2[4] IEC2[4] IPC9[2:0] I2C2 Slave Event _SI2C2Interrupt 45 37 0x00005E IFS2[5] IEC2[5] IPC9[6:4] I2C2 Master Event _MI2C2Interrupt 46 38 0x000060 IFS2[6] IEC2[6] IPC9[10:8] Reserved Reserved 47 39 0x000062 — — — Input Capture/Output Compare 4 _CCP4Interrupt 48 40 0x000064 IFS2[8] IEC2[8] IPC10[2:0] CCP4 Timer _CCT4Interrupt 49 41 0x000066 IFS2[9] IEC2[9] IPC10[6:4] Reserved Reserved 50 42 0x000068 — — — Input Capture/Output Compare 5 _CCP5Interrupt 51 43 0x00006A IFS2[11] IEC2[11] IPC10[14:12] CCP5 Timer _CCT5Interrupt 52 44 0x00006C IFS2[12] IEC2[12] IPC11[2:0] Deadman Timer _DMTInterrupt 53 45 0x00006E IFS2[13] IEC2[13] IPC11[6:4] Note 1: Not all interrupts are available on all packages. Make sure the selected device variant has the interrupt available on the device. DS70005319D-page 96  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 3-24: MASTER INTERRUPT VECTOR DETAILS(1) (CONTINUED) Interrupt Description MPLAB® XC16 ISR Name Input Capture/Output Compare 6 _CCP6Interrupt Vector # IRQ # IVT Address 54 46 Interrupt Bit Location Flag Enable Priority 0x000070 IFS2[14] IEC2[14] IPC11[10:8] IPC11[14:12] CCP6 Timer _CCT6Interrupt 55 47 0x000072 IFS2[15] IEC2[15] QEI Position Counter Compare _QEI1Interrupt 56 48 0x000074 IFS3[0] IEC3[0] IPC12[2:0] UART1 Error _U1EInterrupt 57 49 0x000076 IFS3[1] IEC3[1] IPC12[6:4] UART2 Error _U2EInterrupt 58 50 0x000078 IFS3[2] IEC3[2] IPC12[10:8] CRC Generator _CRCInterrupt 59 51 0x00007A IFS3[3] IEC3[3] IPC12[14:12] CAN1 TX Data Request _C1TXInterrupt 60 52 0x00007C IFS3[4] IEC3[4] IPC13[2:0] Reserved Reserved 61-68 53-60 0x00007E-0x00008C — — — In-Circuit Debugger _ICDInterrupt 69 61 0x00008E IFS3[13] IEC3[13] IPC15[6:4] JTAG Programming _JTAGInterrupt 70 62 0x000090 IFS3[14] IEC3[14] IPC15[10:8] PTG Step _PTGSTEPInterrupt 71 63 0x000092 IFS3[15] IEC3[15] IPC15[14:12] I2C1 Bus Collision _I2C1BCInterrupt 72 64 0x000094 IFS4[0] IEC4[0] IPC16[2:0] I2C2 Bus Collision _I2C2BCInterrupt 73 65 0x000096 IFS4[1] IEC4[1] IPC16[6:4] Reserved Reserved 74 66 0x000098 — — — PWM Generator 1 _PWM1Interrupt 75 67 0x00009A IFS4[3] IEC4[3] IPC16[14:12] PWM Generator 2 _PWM2Interrupt 76 68 0x00009C IFS4[4] IEC4[4] IPC17[2:0] PWM Generator 3 _PWM3Interrupt 77 69 0x00009E IFS4[5] IEC4[5] IPC17[6:4] IPC17[10:8] PWM Generator 4 _PWM4Interrupt Reserved Reserved 78 70 0x0000A0 IFS4[6] IEC4[6] 79-82 71-74 0x0000A2-0x0000A8 — — Change Notice D — _CNDInterrupt 83 75 0x0000AA IFS4[11] IEC4[11] IPC18[14:12] Change Notice E _CNEInterrupt 84 76 0x0000AC IFS4[12] IEC4[12] IPC19[2:0] IPC19[6:4] Comparator 1 _CMP1Interrupt Reserved Reserved 85 77 0x0000AE IFS4[13] IEC4[13] 86-88 78-80 0x0000B0-0x0000B4 — — PTG Watchdog Timer Time-out — _PTGWDTInterrupt 89 81 0x0000B6 IFS5[1] IEC5[1] IPC20[6:4] PTG Trigger 0 _PTG0Interrupt 90 82 0x0000B8 IFS5[2] IEC5[2] IPC20[10:8] PTG Trigger 1 _PTG1Interrupt 91 83 0x0000BA IFS5[3] IEC5[3] IPC20[14:12] PTG Trigger 2 _PTG2Interrupt 92 84 0x0000BC IFS5[4] IEC5[4] IPC21[2:0] PTG Trigger 3 _PTG3Interrupt 93 85 0x0000BE IFS5[5] IEC5[6] IPC21[6:4] SENT1 TX/RX _SENT1Interrupt 94 86 0x0000C0 IFS5[6] IEC5[6] IPC21[10:8] IPC21[14:12] SENT1 Error _SENT1EInterrupt 95 87 0x0000C2 IFS5[7] IEC5[7] SENT2 TX/RX _SENT2Interrupt 96 88 0x0000C4 IFS5[8] IEC5[8] IPC22[2:0] SENT2 Error _SENT2EInterrupt 97 89 0x0000C6 IFS5[9] IEC5[9] IPC22[6:4] ADC Global Interrupt _ADCInterrupt 98 90 0x0000C8 IFS5[10] IEC5[10] IPC22[10:8] ADC AN0 Interrupt _ADCAN0Interrupt 99 91 0x0000CA IFS5[11] IEC5[11] IPC22[14:12] ADC AN1 Interrupt _ADCAN1Interrupt 100 92 0x0000CC IFS5[12] IEC5[12] IPC23[2:0] ADC AN2 Interrupt _ADCAN2Interrupt 101 93 0x0000CE IFS5[13] IEC5[13] IPC23[6:4] ADC AN3 Interrupt _ADCAN3Interrupt 102 94 0x0000D0 IFS5[14] IEC5[14] IPC23[10:8] ADC AN4 Interrupt _ADCAN4Interrupt 103 95 0x0000D2 IFS5[15] IEC5[15] IPC23[14:12] ADC AN5 Interrupt _ADCAN5Interrupt 104 96 0x0000D4 IFS6[0] IEC6[0] IPC24[2:0] ADC AN6 Interrupt _ADCAN6Interrupt 105 97 0x0000D6 IFS6[1] IEC6[1] IPC24[6:4] ADC AN7 Interrupt _ADCAN7Interrupt 106 98 0x0000D8 IFS6[2] IEC6[2] IPC24[10:8] ADC AN8 Interrupt _ADCAN8Interrupt 107 99 0x0000DA IFS6[3] IEC6[3] IPC24[14:12] ADC AN9 Interrupt _ADCAN9Interrupt 108 100 0x0000DC IFS6[4] IEC6[4] IPC25[2:0] ADC AN10 Interrupt _ADCAN10Interrupt 109 101 0x0000DE IFS6[5] IEC6[5] IPC25[6:4] ADC AN11 Interrupt _ADCAN11Interrupt 110 102 0x0000E0 IFS6[6] IEC6[6] IPC25[10:8] Note 1: Not all interrupts are available on all packages. Make sure the selected device variant has the interrupt available on the device.  2017-2019 Microchip Technology Inc. DS70005319D-page 97 dsPIC33CH128MP508 FAMILY TABLE 3-24: MASTER INTERRUPT VECTOR DETAILS(1) (CONTINUED) MPLAB® XC16 ISR Name Vector # IRQ # IVT Address ADC AN12 Interrupt _ADCAN12Interrupt 111 103 ADC AN13 Interrupt _ADCAN13Interrupt 112 ADC AN14 Interrupt _ADCAN14Interrupt 113 ADC AN15 Interrupt _ADCAN15Interrupt ADC AN16 Interrupt Interrupt Description Interrupt Bit Location Flag Enable Priority 0x0000E2 IFS6[7] IEC6[7] IPC25[14:12] 104 0x0000E4 IFS6[8] IEC6[8] IPC26[2:0] 105 0x0000E6 IFS6[9] IEC6[9] IPC26[6:4] 114 106 0x0000E8 IFS6[10] IEC6[10] IPC26[10:8] _ADCAN16Interrupt 115 107 0x0000EA IFS6[11] IEC6[11] IPC26[14:12] ADC AN17 Interrupt _ADCAN17Interrupt 116 108 0x0000EC IFS6[12] IEC6[12] IPC27[2:0] ADC AN18 Interrupt _ADCAN18Interrupt 117 109 0x0000EE IFS6[13] IEC6[13] IPC27[6:4] ADC AN19 Interrupt _ADCAN19Interrupt 118 110 0x0000F0 IFS6[14] IEC6[14] IPC27[10:8] ADC AN20 Interrupt _ADCAN20Interrupt 119 111 0x0000F2 IFS6[15] IEC6[15] IPC27[14:12] Reserved Reserved ADC Fault _ADFLTInterrupt 120-122 112-114 0x0000F4-0x0000F8 123 115 0x0000FA — — — IFS7[3] IEC7[3] IPC28[14:12] ADC Digital Comparator 0 _ADCMP0Interrupt 124 116 0x0000FC IFS7[4] IEC7[4] IPC29[2:0] ADC Digital Comparator 1 _ADCMP1Interrupt 125 117 0x0000FE IFS7[5] IEC7[5] IPC29[6:4] ADC Digital Comparator 2 _ADCMP2Interrupt 126 118 0x000100 IFS7[6] IEC7[6] IPC29[10:8] ADC Digital Comparator 3 _ADCMP3Interrupt 127 119 0x000102 IFS7[7] IEC7[7] IPC29[14:12] ADC Oversample Filter 0 _ADFLTR0Interrupt 128 120 0x000104 IFS7[8] IEC7[8] IPC30[2:0] ADC Oversample Filter 1 _ADFLTR1Interrupt 129 121 0x000106 IFS7[9] IEC7[9] IPC30[6:4] ADC Oversample Filter 2 _ADFLTR2Interrupt 130 122 0x000108 IFS7[10] IEC7[10] IPC30[10:8] ADC Oversample Filter 3 _ADFLTR3Interrupt 131 123 0x00010A IFS7[11] IEC7[11] IPC30[14:12] CLC1 Positive Edge _CLC1PInterrupt 132 124 0x00010C IFS7[12] IEC7[12] IPC31[2:0] CLC2 Positive Edge _CLC2PInterrupt 133 125 0x00010E IFS7[13] IEC7[13] IPC31[6:4] SPI1 Error _SPI1GInterrupt 134 126 0x000110 IFS7[14] IEC7[14] IPC31[10:8] SPI2 Error _SPI2GInterrupt 135 127 0x000112 IFS7[15] IEC7[15] IPC31[14:12] Reserved Reserved 136 128 0x000114 — — — MSI Slave Initiated Interrupt _MSIS1Interrupt 137 129 0x000116 IFS8[1] IEC8[1] IPC32[6:4] MSI Protocol A _MSIAInterrupt 138 130 0x000118 IFS8[2] IEC8[2] IPC32[10:8] MSI Protocol B _MSIBInterrupt 139 131 0x00011A IFS8[3] IEC8[3] IPC32[14:12] MSI Protocol C _MSICInterrupt 140 132 0x00011C IFS8[4] IEC8[4] IPC33[2:0] MSI Protocol D _MSIDInterrupt 141 133 0x00011E IFS8[5] IEC8[5] IPC33[6:4] MSI Protocol E _MSIEInterrupt 142 134 0x000120 IFS8[6] IEC8[6] IPC33[10:8] MSI Protocol F _MSIFInterrupt 143 135 0x000122 IFS8[7] IEC8[7] IPC33[14:12] MSI Protocol G _MSIGInterrupt 144 136 0x000124 IFS8[8] IEC8[8] IPC34[2:0] MSI Protocol H _MSIHInterrupt 145 137 0x000126 IFS8[9] IEC8[9] IPC34[6:4] Master Read FIFO Data Ready _MSIDTInterrupt 146 138 0x000128 IFS8[10] IEC8[10] IPC34[10:8] Master Write FIFO Empty _MSIWFEInterrupt 147 139 0x00012A IFS8[11] IEC8[11] IPC34[14:12] Read or Write FIFO Fault (Over/Underflow) _MSIFLTInterrupt 148 140 0x00012C IFS8[12] IEC8[12] IPC35[2:0] 149 141 0x00012E IFS8[13] IEC8[13] IPC35[6:4] — — — IFS9[2] IEC9[2] IPC36[10:8] MSI Slave Reset _S1RSTInterrupt Reserved Reserved Slave Break _S1BRKInterrupt Reserved Reserved Input Capture/Output Compare 7 _CCP7Interrupt 150-153 142-145 0x000130-0x000136 154 146 0x000138 155-156 147-148 0x00013A-0x00013C 157 149 — — — 0x00013E IFS9[5] IEC9[5] IPC37[6:4] CCP7 Timer _CCT7Interrupt 158 150 0x000140 IFS9[6] IEC9[6] IPC37[10:8] Reserved Reserved 159 151 0x000142 — — — Note 1: Not all interrupts are available on all packages. Make sure the selected device variant has the interrupt available on the device. DS70005319D-page 98  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 3-24: MASTER INTERRUPT VECTOR DETAILS(1) (CONTINUED) Interrupt Description MPLAB® XC16 ISR Name Input Capture/Output Compare 8 _CCP8Interrupt Vector # IRQ # IVT Address 160 152 161 153 Interrupt Bit Location Flag Enable Priority 0x000144 IFS9[8] IEC9[8] IPC38[2:0] 0x000146 IFS9[9] IEC9[9] IPC38[6:4] — — — IFS9[13] IEC9[13] IPC39[6:4] — — — IPC42[2:0] CCP8 Timer _CCT8Interrupt Reserved Reserved Slave Clock Fail _S1CLKFInterrupt Reserved Reserved ADC FIFO Ready _ADFIFOInterrupt 176 168 0x000164 IFS10[8] IEC10[8] PWM Event A _PEVTAInterrupt 177 169 0x000166 IFS10[9] IEC10[9] IPC42[6:4] PWM Event B _PEVTBInterrupt 178 170 0x000168 IFS10[10] IEC10[10] IPC42[10:8] PWM Event C _PEVTCInterrupt 179 171 0x00016A IFS10[11] IEC10[11] IPC42[14:12] PWM Event D _PEVTDInterrupt 180 172 0x00016C IFS10[12] IEC10[12] IPC43[2:0] PWM Event E _PEVTEInterrupt 181 173 0x00016E IFS10[13] IEC10[13] IPC43[6:4] 162-164 154-156 0x000148-0x00014C 165 157 0x00014E 166-175 158-167 0x000150-0x000162 PWM Event F _PEVTFInterrupt 182 174 0x000170 IFS10[14] IEC10[14] IPC43[10:8] CLC3 Positive Edge _CLC3PInterrupt 183 175 0x000172 IFS10[15] IEC10[15] IPC43[14:12] CLC4 Positive Edge _CLC4PInterrupt 184 176 0x000174 IFS11[0] IEC11[0 IPC44[2:0] CLC1 Negative Edge _CLC1NInterrupt 185 177 0x000176 IFS11[1] IEC11[1 IPC44[6:4] CLC2 Negative Edge _CLC2NInterrupt 186 178 0x000178 IFS11[2] IEC11[2 IPC44[10:8] CLC3 Negative Edge _CLC3NInterrupt 187 179 0x00017A IFS11[3] IEC11[3 IPC44[14:]12] CLC4 Negative Edge _CLC4NInterrupt 188 180 IPC45[2:0] Reserved Reserved UART1 Event _U1EVTInterrupt 197 UART2 Event _U2EVTInterrupt 198 0x00017C IFS11[4] IEC11[4 0x0017E-0x0018C — — — 189 0x00018E IFS11[13] IF2C11[13] IPC47[6:4] 190 0x000190 IFS11[14] IF2C11[14] IPC47[12:8] 189-196 181-188 Note 1: Not all interrupts are available on all packages. Make sure the selected device variant has the interrupt available on the device.  2017-2019 Microchip Technology Inc. DS70005319D-page 99 Register Address MASTER INTERRUPT FLAG REGISTERS Bit 15 Bit14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 IFS0 800h INT1IF NVMIF ECCSBEIF U1TXIF U1RXIF SPI1TXIF SPI1RXIF DMA1IF CCT1IF CCP1IF — DMA0IF CNBIF CNAIF T1IF INT0IF IFS1 802h C1RXIF SPI2TXIF SPI2RXIF U2TXIF U2RXIF INT3IF C1IF CCT2IF CCP2IF DMA4IF DMA3IF INT2IF CNCIF DMA2IF MI2C1IF SI2C1IF IFS2 804h CCT6IF CCP6IF DMTIF CCT5IF CCP5IF — CCT4IF CCP4IF — MI2C2IF SI2C2IF CCT3IF CCP3IF DMA5IF — — IFS3 806h PTGSTEPIF JTAGIF ICDIF — — — — — — — — C1TXIF CRCIF U2EIF U1EIF QEI1IF IFS4 808h — — CMP1IF CNEIF CNDIF — — — — PWM4IF PWM3IF PWM2IF PWM1IF — I2C2BCIF I2C1BCIF IFS5 80Ah ADCAN4IF ADCAN3IF ADCAN2IF ADCAN1IF ADCAN0IF ADCIF SENT2EIF SENT2IF SENT1EIF SENT1IF PTG3IF PTG2IF PTG1IF PTG0IF PTGWDTIF — IFS6 80Ch ADCAN20IF ADCAN19IF ADCAN18IF ADCAN17IF ADCAN16IF ADCAN15IF ADCAN14IF ADCAN13IF ADCAN12IF ADCAN11IF ADCAN10IF ADCAN9IF ADCAN8IF ADCAN7IF ADCAN6IF ADCAN5IF IFS7 80Eh SPI2GIF SPI1GIF CLC2PIF CLC1PIF ADFLTR3IF ADFLTR2IF ADFLTR1IF ADFLTR0IF ADCMP3IF ADFLTIF — — — IFS8 810h — — S1SRSTIF MSIFLTIF MSIWFEIF MSIDTIF MSIHIF MSIGIF MSIFIF MSIEIF MSIDIF MSICIF MSIBIF MSIAIF MSIS1IF — IFS9 812h — — S1CLKFIF — — — CCT8IF CCP8IF — CCT7IF CCP7IF — — S1BRKIF — — IFS10 814h CLC3PIF PEVTFIF PEVTEIF PEVTDIF PEVTCIF PEVTBIF PEVTAIF ADFIFOIF — — — — — — — — IFS11 816h — U2EVTIF U1EVTIF — — — — — — — — CLC4NIF CLC3NIF CLC2NIF CLC1NIF CLC4PIF Legend: — = Unimplemented. Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 TABLE 3-26: Register Address ADCMP2IF ADCMP1IF ADCMP0IF MASTER INTERRUPT ENABLE REGISTERS Bit 15 Bit14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 1 Bit 0 IEC0 820h INT1IE NVMIE ECCSBEIE U1TXIE U1RXIE SPI1TXIE SPI1RXIE DMA1IE CCT1IE CCP1IE — DMA0IE CNBIE CNAIE T1IE INT0IE IEC1 822h C1RXIE SPI2TXIE SPI2RXIE U2TXIE U2RXIE INT3IE C1IE CCT2IE CCP2IE DMA4IE DMA3IE INT2IE CNCIE DMA2IE MI2C1IE SI2C1IE IEC2 824h CCT6IE CCP6IE DMTIE CCT5IE CCP5IE — CCT4IE CCP4IE — MI2C2IE SI2C2IE CCT3IE CCP3IE DMA5IE — — IEC3 826h PTGSTEPIE JTAGIE ICDIE — — — — — — — — C1TXIE CRCIE U2EIE U1EIE QEI1IE  2017-2019 Microchip Technology Inc. IEC4 828h — — CMP1IE CNEIE CNDIE — — — — PWM4IE PWM3IE PWM2IE PWM1IE — I2C2BCIE I2C1BCIE IEC5 82Ah ADCAN4IE ADCAN3IE ADCAN2IE ADCAN1IE ADCAN0IE ADCIE SENT2EIE SENT2IE SENT1EIE SENT1IE PTG3IE PTG2IE PTG1IE PTG0IE PTGWDTIE — IEC6 82Ch ADCAN20IE ADCAN19IE ADCAN18IE ADCAN17IE ADCAN16IE ADCAN15IE ADCAN14IE ADCAN13IE ADCAN12IE ADCAN11IE ADCAN10IE ADCAN9IE ADCAN8IE ADCAN7IE ADCAN6IE ADCAN5IE IEC7 82Eh SPI2GIE SPI1GIE CLC2PIE CLC1PIE ADFLTR3IE ADFLTR2IE ADFLTR1IE ADFLTR0IE ADCMP3IE ADCMP2IE ADFLTIE — — — IEC8 830h — — S1SRSTIE MSIFLTIE MSIWFEIE MSIDTIE MSIHIE MSIGIE MSIFIE MSIEIE MSIDIE MSICIE MSIBIE MSIAIE MSIS1IE — IEC9 832h — — S1CLKFIE — — — CCT8IE CCP8IE — CCT7IE CCP7IE — — S1BRKIE — — IEC10 834h CLC3PIE PEVTFIE PEVTEIE PEVTDIE PEVTCIE PEVTBIE PEVTAIE ADFIFOIE — — — — — — — — IEC11 836h — U2EVTIE U1EVTIE — — — — — — — — CLC4NIE CLC3NIE CLC2NIE CLC1NIE CLC4PIE Legend: — = Unimplemented. ADCMP1IE ADCMP0IE dsPIC33CH128MP508 FAMILY DS70005319D-page 100 TABLE 3-25:  2017-2019 Microchip Technology Inc. TABLE 3-27: MASTER INTERRUPT PRIORITY REGISTERS Register Address Bit 15 Bit14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 840h — CNBIP2 CNBIP1 CNBIP0 — CNAIP2 CNAIP1 CNAIP0 — T1IP2 T1IP1 T1IP0 — INT0IP2 INT0IP1 INT0IP0 IPC1 842h — CCT1IP2 CCT1IP1 CCT1IP0 — CCP1IP2 CCP1IP1 CCP1IP0 — — — — — DMA0IP2 DMA0IP1 DMA0IP0 IPC2 844h — U1RXIP2 U1RXIP1 U1RXIP0 — SPI1TXIP2 SPI1TXIP1 SPI1TXIP0 — SPI1RXIP2 SPI1RXIP1 SPI1RXIP0 — DMA1IP2 DMA1IP1 DMA1IP0 IPC3 846h — INT1IP2 INT1IP1 INT1IP0 — NVMIP2 NVMIP1 NVMIP0 — ECCSBEIP2 ECCSBEIP1 ECCSBEIP0 — U1TXIP2 U1TXIP1 U1TXIP0 IPC4 848h — CNCIP2 CNCIP1 CNCIP0 — DMA2IP2 DMA2IP1 DMA2IP0 — MI2C1IP2 MI2C1IP1 MI2C1IP0 — SI2C1IP2 SI2C1IP1 SI2C1IP0 IPC5 84Ah — CCP2IP2 CCP2IP1 CCP2IP0 — DMA4IP2 DMA4IP1 DMA4IP0 — DMA3IP2 DMA3IP1 DMA3IP20 — INT2IP2 INT2IP1 INT2IP0 IPC6 84Ch — U2RXIP2 U2RXIP1 U2RXIP0 — INT3IP2 INT3IP1 INT3IP0 — CAN1IP2 CAN1IP1 CAN1IP0 — CCT2IP2 CCT2IP1 CCT2IP0 IPC7 84Eh — C1RXIP2 C1RXIP1 C1RXIP0 — SPI2TXIP2 SPI2TXIP1 SPI2TXIP0 — SPI2RXIP2 SPI2RXIP1 SPI2RXIP0 — U2TXIP2 U2TXIP1 U2TXIP0 IPC8 850h — CCP3IP2 CCP3IP1 CCP3IP0 — DMA5IP2 DMA5IP1 DMA5IP0 — — — — — — — — IPC9 852h — — — — — MI2C2IP2 MI2C2IP1 MI2C2IP0 — SI2C2IP2 SI2C2IP1 SI2C2IP0 — CCT3IP2 CCT3IP1 CCT3IP0 IPC10 854h — CCP5IP2 CCP5IP1 CCP5IP0 — — — — — CCT4IP2 CCT4IP1 CCT4IP0 — CCP4IP2 CCP4IP1 CCP4IP0 IPC11 856h — CCT6IP2 CCT6IP1 CCT6IP0 — CCP6IP2 CCP6IP1 CCP6IP0 — DMTIP2 DMTIP1 DMTIP0 — CCT5IP2 CCT5IP1 CCT5IP0 IPC12 858h — CRCIP2 CRCIP1 CRCIP0 — U2EIP2 U2EIP1 U2EIP0 — U1EIP2 U1EIP1 U1EIP0 — QEI1IP2 QEI1IP1 QEI1IP0 IPC13 85Ah — — — — — — — — — — — — — C1TXIP2 C1TXIP1 C1TXIP0 IPC14 85Ch — — — — — — — — — — — — — IPC15 85Eh — — JTAGIP2 JTAGIP1 JTAGIP0 — ICDIP2 ICDIP1 ICDIP0 — — — — IPC16 860h — PWM1IP0 — — — — — I2C2BCIP2 I2C2BCIP1 I2C2BCIP0 — I2C1BCIP2 I2C1BCIP1 I2C1BCIP0 IPC17 862h — — — — — PWM4IP2 PWM4IP1 PWM4IP0 — PWM3IP2 PWM3IP1 PWM3IP0 — PWM2IP2 PWM2IP1 PWM2IP0 IPC18 864h — CNDIP2 CNDIP1 CNDIP0 — — — — — — — — — — — — IPC19 866h — — — — — — — — — CMP1IP2 CMP1IP1 CMP1IP0 — CNEIP2 CNEIP1 CNEIP0 IPC20 868h — PTG1IP2 PTG1IP1 PTG1IP0 — PTG0IP2 PTG0IP1 PTG0IP0 — IPC21 86Ah — SENT1EIP2 SENT1EIP1 SENT1EIP0 — SENT1IP2 SENT1IP1 SENT1IP0 — IPC22 86Ch — ADCAN0IP2 ADCAN0IP1 ADCAN0IP0 — ADCIP2 ADCIP1 ADCIP0 — SENT2EIP2 IPC23 86Eh — ADCAN4IP2 ADCAN4IP1 ADCAN4IP0 — ADCAN3IP2 ADCAN3IP1 ADCAN3IP0 — ADCAN2IP2 IPC24 870h — ADCAN8IP2 ADCAN8IP1 ADCAN8IP0 — ADCAN7IP2 ADCAN7IP1 ADCAN7IP0 — ADCAN6IP2 ADCAN6IP1 IPC25 872h — ADCAN12IP2 ADCAN12IP1 ADCAN12IP0 — ADCAN11IP2 ADCAN11IP1 ADCAN11IP0 — IPC26 874h — ADCAN16IP2 ADCAN16IP2 ADCAN16IP2 — ADCAN15IP2 ADCAN15IP1 ADCAN15IP0 — IPC27 876h — ADCAN20IP2 ADCAN20IP1 ADCAN20IP0 — ADCAN19IP2 ADCAN19IP1 ADCAN19IP0 — IPC28 878h — ADFLTIP2 ADFLTIP1 ADFLTIP0 — — — — — — — — — — — — IPC29 87Ah — ADCMP3IP2 ADCMP3IP1 ADCMP3IP0 — ADCMP2IP2 ADCMP2IP1 ADCMP2IP0 — ADCMP1IP2 ADCMP1IP1 ADCMP1IP0 — ADCMP0IP2 ADCMP0IP1 ADCMP0IP0 IPC30 87Ch — ADFLTR3IP2 ADFLTR3IP1 ADFLTR3IP0 — ADFLTR2IP2 ADFLTR2IP1 ADFLTR2IP0 — ADFLTR1IP2 ADFLTR1IP1 ADFLTR1IP0 — ADFLTR0IP2 ADFLTR0IP1 ADFLTR0IP0 IPC31 87Eh — SPI2GIP0 SPI2GIP1 SPI2GIP0 — SPI1GIP2 SPI1GIP1 SPI1GIP0 — CLC2PIP2 CLC2PIP1 CLC2PIP0 — CLC1PIP2 CLC1PIP1 IPC32 880h — MSIBIP2 MSIBIP1 MSIBIP0 — MSIAIP2 MSIAIP1 MSIAIP0 — MSIS1IP2 MSIS1IP1 MSIS1IP0 — — — — IPC33 882h — MSIFIP2 MSIFIP1 MSIFIP0 — MSIEIP2 MSIEIP1 MSIEIP0 — MSIDIP2 MSIDIP1 MSIDIP0 — MSICIP2 MSICIP1 MSICIP0 884h — MSIWFEIP2 MSIWFEIP1 MSIWFEIP0 — MSIDTIP2 MSIDTIP1 MSIDTIP0 — MSIHIP2 MSIHIP1 MSIHIP0 — MSIGIP2 MSIGIP1 MSIGIP0 IPC34 Legend: PTGSTEPIP2 PTGSTEPIP1 PTGSTEPIP0 PWM1IP2 — = Unimplemented. PWM1IP1 PTGWDTIP2 PTGWDTIP1 PTGWDTIP0 — — — — PTG3IP0 — PTG2IP2 PTG2IP1 PTG2IP0 SENT2EIP1 SENT2EIP0 — SENT2IP2 SENT2IP1 SENT2IP0 ADCAN2IP1 ADCAN2IP0 — ADCAN1IP2 ADCAN1IP1 ADCAN1IP0 ADCAN6IP0 — ADCAN5IP2 ADCAN5IP1 ADCAN5IP0 ADCAN10IP2 ADCAN10IP1 ADCAN10IP0 — ADCAN9IP2 ADCAN9IP1 ADCAN9IP0 ADCAN14IP2 ADCAN14IP1 ADCAN14IP0 — ADCAN13IP2 ADCAN13IP1 ADCAN13IP0 ADCAN18IP2 ADCAN18IP1 ADCAN18IP0 — ADCAN17IP2 ADCAN17IP1 ADCAN17IP0 PTG3IP2 PTG3IP1 CLC1PIP0 dsPIC33CH128MP508 FAMILY DS70005319D-page 101 IPC0 MASTER INTERRUPT PRIORITY REGISTERS (CONTINUED) Register Address Bit 15 Bit14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 886h — — — — — — — — — S1SRSTIP2 S1SRSTIP1 S1SRSTIP0 — MSIFLTIP2 MSIFLTIP1 MSIFLTIP0 IPC36 888h — — — — — S1BRKIP2 S1BRKIP1 S1BRKIP0 — — — — — — — — IPC37 88Ah — — — — — CCT7IP2 CCT7IP1 CCT7IP0 — CCP7IP2 CCP7IP1 CCP7IP0 — — — — IPC38 88Ch — — — — — — — — — CCT8IP2 CCT8IP1 CCT8IP0 — CCP8IP2 CCP8IP1 CCP8IP0 IPC35 IPC39 88Eh — — — — — — — — — S1CLKFIP2 S1CLKFIP1 S1CLKFIP0 — — — — IPC40 890h — — — — — — — — — — — — — — — — IPC41 892h — — — — — — — — — — — — — — — — IPC42 894h — PEVTCIP2 PEVTCIP1 PEVTCIP0 — PEVTBIP2 PEVTBIP1 PEVTBIP0 — PEVTAIP2 PEVTAIP1 PEVTAIP0 — ADFIFOIP2 ADFIFOIP1 ADFIFOIP0 IPC43 896h — CLC3PIP2 CLC3PIP1 CLC3PIP0 — PEVTFIP2 PEVTFIP1 PEVTFIP0 — PEVTEIP2 PEVTEIP1 PEVTEIP0 — PEVTDIP2 PEVTDIP1 PEVTDIP0 IPC44 898h — CLC3NIP2 CLC3NIP1 CLC3NIP0 — CLC2NIP2 CLC2NIP1 CLC2NIP0 — CLC1NIP2 CLC1NIP1 CLC1NIP0 — CLC4PIP2 CLC4PIP1 CLC4PIP0 IPC45 89Ah — — — — — — — — — — — — — CLC4NIP2 CLC4NIP1 CLC4NIP0 IPC46 89Ch — — — — — — — — — — — — — — — — IPC47 89Eh — — — — — U2EVTIP2 U2EVTIP1 U2EVTIP0 — U1EVTIP2 U1EVTIP1 U1EVTIP0 — — — — Legend: — = Unimplemented. dsPIC33CH128MP508 FAMILY DS70005319D-page 102 TABLE 3-27:  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.5.3 INTERRUPT RESOURCES 3.5.4.4 IPCx Many useful resources are provided on the main product page of the Microchip website for the devices listed in this data sheet. This product page contains the latest updates and additional information. The IPCx registers are used to set the Interrupt Priority Level (IPL) for each source of interrupt. Each user interrupt source can be assigned to one of seven priority levels. 3.5.3.1 3.5.4.5 Key Resources • “Interrupts” (www.microchip.com/DS70000600) in the “dsPIC33/PIC24 Family Reference Manual” • Code Samples • Application Notes • Software Libraries • Webinars • All Related “dsPIC33/PIC24 Family Reference Manual” Sections • Development Tools 3.5.4 INTERRUPT CONTROL AND STATUS REGISTERS The dsPIC33CH128MP508 family devices implement the following registers for the interrupt controller: • • • • • INTCON1 INTCON2 INTCON3 INTCON4 INTTREG 3.5.4.1 INTCON1 through INTCON4 Global interrupt control functions are controlled from INTCON1, INTCON2, INTCON3 and INTCON4. INTCON1 contains the Interrupt Nesting Disable bit (NSTDIS), as well as the control and status flags for the processor trap sources. The INTCON2 register controls external interrupt request signal behavior, contains the Global Interrupt Enable bit (GIE) and the Alternate Interrupt Vector Table Enable bit (AIVTEN). INTTREG The INTTREG register contains the associated interrupt vector number and the new CPU Interrupt Priority Level, which are latched into the Vector Number (VECNUM[7:0]) and Interrupt Level bits (ILR[3:0]) fields in the INTTREG register. The new Interrupt Priority Level is the priority of the pending interrupt. The interrupt sources are assigned to the IFSx, IECx and IPCx registers in the same sequence as they are listed in Table 3-24. For example, INT0 (External Interrupt 0) is shown as having Vector Number 8 and a natural order priority of 0. Thus, the INT0IF bit is found in IFS0[0], the INT0IE bit in IEC0[0] and the INT0IP[2:0] bits in the first position of IPC0 (IPC0[2:0]). 3.5.4.6 Status/Control Registers Although these registers are not specifically part of the interrupt control hardware, two of the CPU Control registers contain bits that control interrupt functionality. For more information on these registers, refer to “Enhanced CPU” (www.microchip.com/DS70005158) in the “dsPIC33/PIC24 Family Reference Manual”. • The CPU STATUS Register, SR, contains the IPL[2:0] bits (SR[7:5]). These bits indicate the current CPU Interrupt Priority Level. The user software can change the current CPU Interrupt Priority Level by writing to the IPLx bits. • The CORCON register contains the IPL3 bit, which together with IPL[2:0], also indicates the current CPU priority level. IPL3 is a read-only bit so that trap events cannot be masked by the user software. INTCON3 contains the status flags for the Auxiliary PLL and DO stack overflow status trap sources. All Interrupt registers are described in Register 3-19 through Register 3-23 in the following pages. The INTCON4 register contains the Generated Hard Trap Status bit (SGHT). 3.5.4.7 3.5.4.2 Software IFSx The IFSx registers maintain all of the interrupt request flags. Each source of interrupt has a status bit, which is set by the respective peripherals or external signal and is cleared via software. 3.5.4.3 IECx The IECx registers maintain all of the interrupt enable bits. These control bits are used to individually enable interrupts from the peripherals or external signals.  2017-2019 Microchip Technology Inc. Cross Core Interrupts There are three interrupts that can occur in the Master core based on the Slave events: • S1RSTIF is a Slave Reset interrupt which gets set in the Master if the Slave gets a Reset. This interrupt is enabled only when the SRTSIE bit (MSI1CON[7]) is set. • S1CLKIF is a Master interrupt which gets set if the Slave core loses its system clock. • S1BRKIF is the Slave Break interrupt. This interrupt gets set in the Master if the Slave stops at a breakpoint (valid only when the Slave is being debugged). DS70005319D-page 103 dsPIC33CH128MP508 FAMILY 3.5.5 INTERRUPT STATUS/CONTROL REGISTERS SR: CPU STATUS REGISTER(1) REGISTER 3-17: R/W-0 R/W-0 R/W-0 R/W-0 R/C-0 R/C-0 R-0 R/W-0 OA OB SA SB OAB SAB DA DC bit 15 bit 8 R/W-0(3) R/W-0(3) IPL2(2) IPL1 (2) R/W-0(3) IPL0 (2) R-0 R/W-0 R/W-0 R/W-0 R/W-0 RA N OV Z C bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’= Bit is set ‘0’ = Bit is cleared x = Bit is unknown IPL[2:0]: CPU Interrupt Priority Level Status bits(2,3) 111 = CPU Interrupt Priority Level is 7 (15); user interrupts are disabled 110 = CPU Interrupt Priority Level is 6 (14) 101 = CPU Interrupt Priority Level is 5 (13) 100 = CPU Interrupt Priority Level is 4 (12) 011 = CPU Interrupt Priority Level is 3 (11) 010 = CPU Interrupt Priority Level is 2 (10) 001 = CPU Interrupt Priority Level is 1 (9) 000 = CPU Interrupt Priority Level is 0 (8) bit 7-5 Note 1: 2: 3: For complete register details, see Register 3-1. The IPL[2:0] bits are concatenated with the IPL[3] bit (CORCON[3]) to form the CPU Interrupt Priority Level. The value in parentheses indicates the IPL, if IPL[3] = 1. User interrupts are disabled when IPL[3] = 1. The IPL[2:0] Status bits are read-only when the NSTDIS bit (INTCON1[15]) = 1. DS70005319D-page 104  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-18: CORCON: CORE CONTROL REGISTER(1) R/W-0 U-0 R/W-0 R/W-0 R/W-0 R-0 R-0 R-0 VAR — US1 US0 EDT DL2 DL1 DL0 bit 15 bit 8 R/W-0 R/W-0 R/W-1 R/W-0 R/C-0 R-0 R/W-0 R/W-0 SATA SATB SATDW ACCSAT IPL3(2) SFA RND IF bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’= Bit is set ‘0’ = Bit is cleared bit 15 VAR: Variable Exception Processing Latency Control bit 1 = Variable exception processing is enabled 0 = Fixed exception processing is enabled bit 3 IPL3: CPU Interrupt Priority Level Status bit 3(2) 1 = CPU Interrupt Priority Level is greater than 7 0 = CPU Interrupt Priority Level is 7 or less Note 1: 2: x = Bit is unknown For complete register details, see Register 3-2. The IPL3 bit is concatenated with the IPL[2:0] bits (SR[7:5]) to form the CPU Interrupt Priority Level.  2017-2019 Microchip Technology Inc. DS70005319D-page 105 dsPIC33CH128MP508 FAMILY REGISTER 3-19: INTCON1: INTERRUPT CONTROL REGISTER 1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 NSTDIS OVAERR OVBERR COVAERR COVBERR OVATE OVBTE COVTE bit 15 bit 8 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 SFTACERR DIV0ERR — MATHERR ADDRERR STKERR OSCFAIL — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 NSTDIS: Interrupt Nesting Disable bit 1 = Interrupt nesting is disabled 0 = Interrupt nesting is enabled bit 14 OVAERR: Accumulator A Overflow Trap Flag bit 1 = Trap was caused by an overflow of Accumulator A 0 = Trap was not caused by an overflow of Accumulator A bit 13 OVBERR: Accumulator B Overflow Trap Flag bit 1 = Trap was caused by an overflow of Accumulator B 0 = Trap was not caused by an overflow of Accumulator B bit 12 COVAERR: Accumulator A Catastrophic Overflow Trap Flag bit 1 = Trap was caused by a catastrophic overflow of Accumulator A 0 = Trap was not caused by a catastrophic overflow of Accumulator A bit 11 COVBERR: Accumulator B Catastrophic Overflow Trap Flag bit 1 = Trap was caused by a catastrophic overflow of Accumulator B 0 = Trap was not caused by a catastrophic overflow of Accumulator B bit 10 OVATE: Accumulator A Overflow Trap Enable bit 1 = Trap overflow of Accumulator A 0 = Trap is disabled bit 9 OVBTE: Accumulator B Overflow Trap Enable bit 1 = Trap overflow of Accumulator B 0 = Trap is disabled bit 8 COVTE: Catastrophic Overflow Trap Enable bit 1 = Trap catastrophic overflow of Accumulator A or B is enabled 0 = Trap is disabled bit 7 SFTACERR: Shift Accumulator Error Status bit 1 = Math error trap was caused by an invalid accumulator shift 0 = Math error trap was not caused by an invalid accumulator shift DS70005319D-page 106  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-19: INTCON1: INTERRUPT CONTROL REGISTER 1 (CONTINUED) bit 6 DIV0ERR: Divide-by-Zero Error Status bit 1 = Math error trap was caused by a divide-by-zero 0 = Math error trap was not caused by a divide-by-zero bit 5 Unimplemented: Read as ‘0’ bit 4 MATHERR: Math Error Status bit 1 = Math error trap has occurred 0 = Math error trap has not occurred bit 3 ADDRERR: Address Error Trap Status bit 1 = Address error trap has occurred 0 = Address error trap has not occurred bit 2 STKERR: Stack Error Trap Status bit 1 = Stack error trap has occurred 0 = Stack error trap has not occurred bit 1 OSCFAIL: Oscillator Failure Trap Status bit 1 = Oscillator failure trap has occurred 0 = Oscillator failure trap has not occurred bit 0 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. DS70005319D-page 107 dsPIC33CH128MP508 FAMILY REGISTER 3-20: INTCON2: INTERRUPT CONTROL REGISTER 2 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0 R/W-0 GIE DISI SWTRAP — — — — AIVTEN bit 15 bit 8 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — — INT3EP INT2EP INT1EP INT0EP bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 GIE: Global Interrupt Enable bit 1 = Interrupts and associated IE bits are enabled 0 = Interrupts are disabled, but traps are still enabled bit 14 DISI: DISI Instruction Status bit 1 = DISI instruction is active 0 = DISI instruction is not active bit 13 SWTRAP: Software Trap Status bit 1 = Software trap is enabled 0 = Software trap is disabled bit 12-9 Unimplemented: Read as ‘0’ bit 8 AIVTEN: Alternate Interrupt Vector Table Enable bit 1 = Uses Alternate Interrupt Vector Table 0 = Uses standard Interrupt Vector Table bit 7-4 Unimplemented: Read as ‘0’ bit 3 INT3EP: External Interrupt 3 Edge Detect Polarity Select bit 1 = Interrupt on negative edge 0 = Interrupt on positive edge bit 2 INT2EP: External Interrupt 2 Edge Detect Polarity Select bit 1 = Interrupt on negative edge 0 = Interrupt on positive edge bit 1 INT1EP: External Interrupt 1 Edge Detect Polarity Select bit 1 = Interrupt on negative edge 0 = Interrupt on positive edge bit 0 INT0EP: External Interrupt 0 Edge Detect Polarity Select bit 1 = Interrupt on negative edge 0 = Interrupt on positive edge DS70005319D-page 108 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-21: INTCON3: INTERRUPT CONTROL REGISTER 3 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 — — — — — — CAN NAE bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 U-0 U-0 U-0 R/W-0 — — DAE DOOVR — — — APLL bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-10 Unimplemented: Read as ‘0’ bit 9 CAN: CAN Address Error Soft Trap Status bit 1 = CAN address error soft trap has occurred 0 = CAN address error soft trap has not occurred bit 8 NAE: NVM Address Error Soft Trap Status bit 1 = NVM address error soft trap has occurred 0 = NVM address error soft trap has not occurred bit 7-6 Unimplemented: Read as ‘0’ bit 5 DAE: DMA Address Error (Soft) Trap Status bit 1 = DMA address error trap has occurred 0 = DMA address error trap has not occurred bit 4 DOOVR: DO Stack Overflow Soft Trap Status bit 1 = DO stack overflow soft trap has occurred 0 = DO stack overflow soft trap has not occurred bit 3-1 Unimplemented: Read as ‘0’ bit 0 APLL: Auxiliary PLL Loss of Lock Soft Trap Status bit 1 = APLL lock soft trap has occurred 0 = APLL lock soft trap has not occurred  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 109 dsPIC33CH128MP508 FAMILY REGISTER 3-22: INTCON4: INTERRUPT CONTROL REGISTER 4 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 — — — — — — ECCDBE SGHT bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-2 Unimplemented: Read as ‘0’ bit 1 ECCDBE: ECC Double-Bit Error Trap bit 1 = ECC double-bit error trap has occurred 0 = ECC double-bit error trap has not occurred bit 0 SGHT: Software Generated Hard Trap Status bit 1 = Software generated hard trap has occurred 0 = Software generated hard trap has not occurred DS70005319D-page 110 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-23: INTTREG: INTERRUPT CONTROL AND STATUS REGISTER U-0 U-0 R-0 U-0 R-0 R-0 R-0 R-0 — — VHOLD — ILR3 ILR2 ILR1 ILR0 bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 VECNUM[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 VHOLD: Vector Number Capture Enable bit 1 = VECNUM[7:0] bits read current value of vector number encoding tree (i.e., highest priority pending interrupt) 0 = Vector number latched into VECNUM[7:0] at Interrupt Acknowledge and retained until next IACK bit 12 Unimplemented: Read as ‘0’ bit 11-8 ILR[3:0]: New CPU Interrupt Priority Level bits 1111 = CPU Interrupt Priority Level is 15 ... 0001 = CPU Interrupt Priority Level is 1 0000 = CPU Interrupt Priority Level is 0 bit 7-0 VECNUM[7:0]: Vector Number of Pending Interrupt bits 11111111 = 255, Reserved; do not use ... 00001001 = 9, IC1 – Input Capture 1 00001000 = 8, INT0 – External Interrupt 0 00000111 = 7, Reserved; do not use 00000110 = 6, Generic soft error trap 00000101 = 5, Reserved; do not use 00000100 = 4, Math error trap 00000011 = 3, Stack error trap 00000010 = 2, Generic hard trap 00000001 = 1, Address error trap 00000000 = 0, Oscillator fail trap  2017-2019 Microchip Technology Inc. DS70005319D-page 111 dsPIC33CH128MP508 FAMILY 3.6 Master I/O Ports Note: Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “I/O Ports with Edge Detect” (www.microchip.com/DS70005322) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). 2: The I/O ports are shared by Master core and Slave core. All input goes to both the Master and Slave. The I/O ownership is defined by the Configuration bits. 3: The TMS pin function may be active multiple times during ICSP™ device erase, programming and debugging. When the TMS function is active, the integrated pull-up resistor will pull the pin to VDD. Proper care should be taken if there are sensitive circuits connected on the TMS pin during programming/erase and debugging. Many of the device pins are shared among the peripherals and the Parallel I/O ports. All I/O input ports feature Schmitt Trigger inputs for improved noise immunity. The Master and Slave have the same number of I/O ports and are shared. The Master PORT registers are located in the Master SFR and the Slave PORT registers are located in the Slave SFR, respectively. Some of the key features of the I/O ports are: The output functionality of the ports is defined by the Configuration registers, FCFGPRA0 to FCFGPRE0. When these Configuration bits are maintained as ‘1’, the Master owns the pin (only the output function); when the bits are ‘0’, the ownership of that specific pin belongs to the Slave. The input function of the I/O is valid for both Master and Slave. The Configuration registers, FCFGPRA0 to FCFGPRE0, do not have any control over the input function. 3.6.1 PARALLEL I/O (PIO) PORTS All port pins have 12 registers directly associated with their operation as digital I/Os. The Data Direction register (TRISx) determines whether the pin is an input or an output. If the data direction bit is a ‘1’, then the pin is an input. All port pins are defined as inputs after a Reset. Reads from the latch (LATx), read the latch. Writes to the latch, write the latch. Reads from the port (PORTx), read the port pins, while writes to the port pins, write the latch. Any bit and its associated data and control registers that are not valid for a particular device are disabled. This means the corresponding LATx and TRISx registers, and the port pin are read as zeros. When a pin is shared with another peripheral or function that is defined as an input only, it is nevertheless regarded as a dedicated port because there is no other competing source of outputs. Table 3-28 shows the pin availability. Table 3-29 shows the 5V input tolerant pins across this device. • Individual Output Pin Open-Drain Enable/Disable • Individual Input Pin Weak Pull-up and Pull-Down • Monitor Selective Inputs and Generate Interrupt when Change in Pin State is Detected • Operation during Sleep and Idle modes DS70005319D-page 112  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 3-28: PIN AND ANSELx AVAILABILITY Device Rx15 Rx14 Rx13 Rx12 Rx11 Rx10 Rx9 Rx8 Rx7 Rx6 Rx5 Rx4 Rx3 Rx2 Rx1 Rx0 PORTA dsPIC33XXXMP508/208 — — — — — — — — — — — X X X X X dsPIC33XXXMP506/206 — — — — — — — — — — — X X X X X dsPIC33XXXMP505/205 — — — — — — — — — — — X X X X X dsPIC33XXXMP503/203 — — — — — — — — — — — X X X X X dsPIC33XXXMP502/202 — — — — — — — — — — — X X X X X ANSELA — — — — — — — — — — — X X X X X PORTB dsPIC33XXXMP508/208 X X X X X X X X X X X X X X X X dsPIC33XXXMP506/206 X X X X X X X X X X X X X X X X dsPIC33XXXMP505/205 X X X X X X X X X X X X X X X X dsPIC33XXXMP503/203 X X X X X X X X X X X X X X X X dsPIC33XXXMP502/202 X X X X X X X X X X X X X X X X ANSELB — — — — — — X X X — — — X X X X PORTC dsPIC33XXXMP508/208 X X X X X X X X X X X X X X X X dsPIC33XXXMP506/206 X X X X X X X X X X X X X X X X dsPIC33XXXMP505/205 — — X X X X X X X X X X X X X X dsPIC33XXXMP503/203 — — — — — — — — — — X X X X X X dsPIC33XXXMP502/202 — — — — — — — — — — — — — — — — ANSELC — — — — — — — — X — — — X X X X dsPIC33XXXMP508/208 X X X X X X X X X X X X X X X X dsPIC33XXXMP506/206 X X X X X X X X X X X X X X X X dsPIC33XXXMP505/205 — — X — — X — X — — — — — — X — dsPIC33XXXMP503/203 — — — — — — — — — — — — — — — — dsPIC33XXXMP502/202 — — — — — — — — — — — — — — — — ANSELD — — — — — X — — — — — — — — — — PORTD PORTE dsPIC33XXXMP508/208 X X X X X X X X X X X X X X X X dsPIC33XXXMP506/206 — — — — — — — — — — — — — — — — dsPIC33XXXMP505/205 — — — — — — — — — — — — — — — — dsPIC33XXXMP503/203 — — — — — — — — — — — — — — — — dsPIC33XXXMP502/202 — — — — — — — — — — — — — — — — TABLE 3-29: PORTA — — — — — RA4 RA3 RA2 RA1 RA0 RB15 RB14 RB13 RB12 RB11 RB10 RB9 RB8 RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0 PORTC RC15 RC14 RC13 RC12 RC11 RC10 RC9 RC8 RC7 RC6 RC5 RC4 RC3 RC2 RC1 RC0 PORTD RD15 RD14 RD13 RD12 RD11 RD10 RD9 RD8 RD7 RD6 RD5 RD4 RD3 RD2 RD1 RD0 PORTE RE9 RE8 RE7 RE6 RE5 RE4 RE3 RE2 RE1 RE0 PORTB Legend: — 5V INPUT TOLERANT PORTS — — — — — RE15 RE14 RE13 RE12 RE11 RE10 Shaded pins are up to 5.5 VDC input tolerant.  2017-2019 Microchip Technology Inc. DS70005319D-page 113 dsPIC33CH128MP508 FAMILY FIGURE 3-19: BLOCK DIAGRAM OF A TYPICAL SHARED PORT STRUCTURE Peripheral Module Output Multiplexers Peripheral Input Data Peripheral Module Enable Peripheral Output Enable Peripheral Output Data PIO Module WR TRISx Output Enable 0 1 Output Data 0 Read TRISx Data Bus I/O 1 D Q I/O Pin CK TRISx Latch D WR LATx + WR PORTx Q CK Data Latch Read LATx Input Data Read PORTx DS70005319D-page 114  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.6.1.1 Open-Drain Configuration In addition to the PORTx, LATx and TRISx registers for data control, port pins can also be individually configured for either digital or open-drain output. This is controlled by the Open-Drain Enable for PORTx register, ODCx, associated with each port. Setting any of the bits configures the corresponding pin to act as an open-drain output. The open-drain feature allows the generation of outputs, other than VDD, by using external pull-up resistors. The maximum open-drain voltage allowed on any pin is the same as the maximum VIH specification for that particular pin. 3.6.2 CONFIGURING ANALOG AND DIGITAL PORT PINS The ANSELx registers control the operation of the analog port pins. The port pins that are to function as analog inputs or outputs must have their corresponding ANSELx and TRISx bits set. In order to use port pins for I/O functionality with digital modules, such as timers, UARTs, etc., the corresponding ANSELx bit must be cleared. The ANSELx registers have a default value of 0xFFFF; therefore, all pins that share analog functions are analog (not digital) by default. Pins with analog functions affected by the ANSELx registers are listed with a buffer type of analog in the Pinout I/O Descriptions (see Table 1-1). When the PORTx register is read, all pins configured as analog input channels are read as cleared (a low level). Pins configured as digital inputs do not convert an analog input. Analog levels on any pin, defined as a digital input (including the ANx pins), can cause the input buffer to consume current that exceeds the device specifications. 3.6.2.1 I/O Port Write/Read Timing One instruction cycle is required between a port direction change or port write operation and a read operation of the same port. Typically, this instruction would be a NOP. The following registers are in the PORT module: • • • • • • • • • • • • Register 3-24: ANSELx (one per port) Register 3-25: TRISx (one per port) Register 3-26: PORTx (one per port) Register 3-27: LATx (one per port) Register 3-28: ODCx (one per port) Register 3-29: CNPUx (one per port) Register 3-30: CNPDx (one per port) Register 3-31: CNCONx (one per port – optional) Register 3-32: CNEN0x (one per port) Register 3-33: CNSTATx (one per port – optional) Register 3-34: CNEN1x (one per port) Register 3-35: CNFx (one per port) If the TRISx bit is cleared (output) while the ANSELx bit is set, the digital output level (VOH or VOL) is converted by an analog peripheral, such as the ADC module or comparator module.  2017-2019 Microchip Technology Inc. DS70005319D-page 115 dsPIC33CH128MP508 FAMILY 3.6.3 MASTER PORT CONTROL REGISTERS REGISTER 3-24: R/W-1 ANSELx: ANALOG SELECT FOR PORTx REGISTER R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 ANSELx[15:8] bit 15 bit 8 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 ANSELx[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown ANSELx[15:0]: Analog Select for PORTx bits 1 = Analog input is enabled and digital input is disabled on the PORTx[n] pin 0 = Analog input is disabled and digital input is enabled on the PORTx[n] pin DS70005319D-page 116  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-25: R/W-1 TRISx: OUTPUT ENABLE FOR PORTx REGISTER R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 TRISx[15:8] bit 15 bit 8 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 TRISx[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown TRISx[15:0]: Output Enable for PORTx bits 1 = LATx[n] is not driven on the PORTx[n] pin 0 = LATx[n] is driven on the PORTx[n] pin REGISTER 3-26: R/W-1 PORTx: INPUT DATA FOR PORTx REGISTER R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 PORTx[15:8] bit 15 bit 8 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 PORTx[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown PORTx[15:0]: PORTx Data Input Value bits  2017-2019 Microchip Technology Inc. DS70005319D-page 117 dsPIC33CH128MP508 FAMILY REGISTER 3-27: R/W-x LATx: OUTPUT DATA FOR PORTx REGISTER R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x LATx[15:8] bit 15 bit 8 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x LATx[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown LATx[15:0]: PORTx Data Output Value bits REGISTER 3-28: R/W-0 ODCx: OPEN-DRAIN ENABLE FOR PORTx REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ODCx[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ODCx[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown ODCx[15:0]: PORTx Open-Drain Enable bits 1 = Open-drain is enabled on the PORTx pin 0 = Open-drain is disabled on the PORTx pin DS70005319D-page 118  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-29: R/W-0 CNPUx: CHANGE NOTIFICATION PULL-UP ENABLE FOR PORTx REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CNPUx[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CNPUx[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown CNPUx[15:0]: Change Notification Pull-up Enable for PORTx bits 1 = The pull-up for PORTx[n] is enabled – takes precedence over the pull-down selection 0 = The pull-up for PORTx[n] is disabled REGISTER 3-30: R/W-0 CNPDx: CHANGE NOTIFICATION PULL-DOWN ENABLE FOR PORTx REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CNPDx[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CNPDx[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown CNPDx[15:0]: Change Notification Pull-Down Enable for PORTx bits 1 = The pull-down for PORTx[n] is enabled (if the pull-up for PORTx[n] is not enabled) 0 = The pull-down for PORTx[n] is disabled  2017-2019 Microchip Technology Inc. DS70005319D-page 119 dsPIC33CH128MP508 FAMILY REGISTER 3-31: CNCONx: CHANGE NOTIFICATION CONTROL FOR PORTx REGISTER R/W-0 U-0 U-0 U-0 R/W-0 U-0 U-0 U-0 ON — — — CNSTYLE — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ON: Change Notification (CN) Control for PORTx On bit 1 = CN is enabled 0 = CN is disabled bit 14-12 Unimplemented: Read as ‘0’ bit 11 CNSTYLE: Change Notification Style Selection bit 1 = Edge style (detects edge transitions, CNFx[15:0] bits are used for a Change Notification event) 0 = Mismatch style (detects change from last port read, CNSTATx[15:0] bits are used for a Change Notification event) bit 10-0 Unimplemented: Read as ‘0’ REGISTER 3-32: R/W-0 CNEN0x: INTERRUPT CHANGE NOTIFICATION ENABLE FOR PORTx REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CNEN0x[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CNEN0x[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown CNEN0x[15:0]: Interrupt Change Notification Enable for PORTx bits 1 = Interrupt-on-change (from the last read value) is enabled for PORTx[n] 0 = Interrupt-on-change is disabled for PORTx[n] DS70005319D-page 120  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-33: R-0 CNSTATx: INTERRUPT CHANGE NOTIFICATION STATUS FOR PORTx REGISTER R-0 R-0 R-0 R-0 R-0 R-0 R-0 CNSTATx[15:8] bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 CNSTATx[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown CNSTATx[15:0]: Interrupt Change Notification Status for PORTx bits When CNSTYLE (CNCONx[11]) = 0: 1 = Change occurred on PORTx[n] since last read of PORTx[n] 0 = Change did not occur on PORTx[n] since last read of PORTx[n] REGISTER 3-34: R/W-0 CNEN1x: INTERRUPT CHANGE NOTIFICATION EDGE SELECT FOR PORTx REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CNEN1x[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CNEN1x[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown CNEN1x[15:0]: Interrupt Change Notification Edge Select for PORTx bits  2017-2019 Microchip Technology Inc. DS70005319D-page 121 dsPIC33CH128MP508 FAMILY REGISTER 3-35: R/W-0 CNFx: INTERRUPT CHANGE NOTIFICATION FLAG FOR PORTx REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CNFx[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CNFx[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15- x = Bit is unknown CNFx[15:0]: Interrupt Change Notification Flag for PORTx bits When CNSTYLE (CNCONx[11]) = 1: 1 = An enabled edge event occurred on the PORTx[n] pin 0 = An enabled edge event did not occur on the PORTx[n] pin DS70005319D-page 122  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.6.4 INPUT CHANGE NOTIFICATION (ICN) The Input Change Notification function of the I/O ports allows the dsPIC33CH128MP508 family devices to generate interrupt requests to the processor in response to a Change-of-State (COS) on selected input pins. This feature can detect input Change-of-States, even in Sleep mode, when the clocks are disabled. Every I/O port pin can be selected (enabled) for generating an interrupt request on a Change-of-State. Five control registers are associated with the Change Notification (CN) functionality of each I/O port. To enable the Change Notification feature for the port, the ON bit (CNCONx[15]) must be set. The CNEN0x and CNEN1x registers contain the CN interrupt enable control bits for each of the input pins. The setting of these bits enables a CN interrupt for the corresponding pins. Also, these bits, in combination with the CNSTYLE bit (CNCONx[11]), define a type of transition when the interrupt is generated. Possible CN event options are listed in Table 3-30. TABLE 3-30: CNSTYLE Bit (CNCONx[11]) CHANGE NOTIFICATION EVENT OPTIONS CNEN1x CNEN0x Bit Bit Change Notification Event Description 3.6.5 PERIPHERAL PIN SELECT (PPS) A major challenge in general purpose devices is providing the largest possible set of peripheral features, while minimizing the conflict of features on I/O pins. The challenge is even greater on low pin count devices. In an application where more than one peripheral needs to be assigned to a single pin, inconvenient work arounds in application code, or a complete redesign, may be the only option. Peripheral Pin Select configuration provides an alternative to these choices by enabling peripheral set selection and placement on a wide range of I/O pins. By increasing the pinout options available on a particular device, users can better tailor the device to their entire application, rather than trimming the application to fit the device. The Peripheral Pin Select configuration feature operates over a fixed subset of digital I/O pins. Users may independently map the input and/or output of most digital peripherals to any one of these I/O pins. Hardware safeguards are included that prevent accidental or spurious changes to the peripheral mapping once it has been established. 3.6.6 AVAILABLE PINS 0 Does not matter 0 Disabled 0 Does not matter 1 Detects a mismatch between the last read state and the current state of the pin 1 0 0 Disabled The number of available pins is dependent on the particular device and its pin count. Pins that support the Peripheral Pin Select feature include the label, “RPn”, in their full pin designation, where “n” is the remappable pin number. “RP” is used to designate pins that support both remappable input and output functions. 1 0 1 Detects a positive transition only (from ‘0’ to ‘1’) 3.6.7 1 1 0 Detects a negative transition only (from ‘1’ to ‘0’) 1 1 1 Detects both positive and negative transitions The peripherals managed by the Peripheral Pin Select are all digital only peripherals. These include general serial communications (UART and SPI), general purpose timer clock inputs, timer-related peripherals (input capture and output compare) and interrupt-on-change inputs. The CNSTATx register indicates whether a change occurred on the corresponding pin since the last read of the PORTx bit. In addition to the CNSTATx register, the CNFx register is implemented for each port. This register contains flags for Change Notification events. These flags are set if the valid transition edge, selected in the CNEN0x and CNEN1x registers, is detected. CNFx stores the occurrence of the event. CNFx bits must be cleared in software to get the next Change Notification interrupt. The CN interrupt is generated only for the I/Os configured as inputs (corresponding TRISx bits must be set). Note: Pull-ups and pull-downs on Input Change Notification pins should always be disabled when the port pin is configured as a digital output.  2017-2019 Microchip Technology Inc. AVAILABLE PERIPHERALS In comparison, some digital only peripheral modules are never included in the Peripheral Pin Select feature. This is because the peripheral’s function requires special I/O circuitry on a specific port and cannot be easily connected to multiple pins. One example includes I2C modules. A similar requirement excludes all modules with analog inputs, such as the A/D Converter (ADC) A key difference between remappable and nonremappable peripherals is that remappable peripherals are not associated with a default I/O pin. The peripheral must always be assigned to a specific I/O pin before it can be used. In contrast, non-remappable peripherals are always available on a default pin, assuming that the peripheral is active and not conflicting with another peripheral. DS70005319D-page 123 dsPIC33CH128MP508 FAMILY When a remappable peripheral is active on a given I/O pin, it takes priority over all other digital I/Os and digital communication peripherals associated with the pin. Priority is given regardless of the type of peripheral that is mapped. Remappable peripherals never take priority over any analog functions associated with the pin. 3.6.8 CONTROLLING CONFIGURATION CHANGES Because peripheral mapping can be changed during run time, some restrictions on peripheral remapping are needed to prevent accidental configuration changes. The dsPIC33CH128MP508 devices have implemented the control register lock sequence. 3.6.8.1 CONTROL REGISTER LOCK Under normal operation, writes to the RPINRx and RPORx registers are not allowed. Attempted writes will appear to execute normally, but the contents of the registers will remain unchanged. To change these registers, they must be unlocked in hardware. The register lock is controlled by the IOLOCK bit (RPCON[11]). Setting IOLOCK prevents writes to the control registers; clearing IOLOCK allows writes. To set or clear IOLOCK, the NVMKEY unlock sequence must be executed: 1. 2. 3. Write 0x55 to NVMKEY. Write 0xAA to NVMKEY. Clear (or set) IOLOCK as a single operation. IOLOCK remains in one state until changed. This allows all of the Peripheral Pin Selects to be configured with a single unlock sequence, followed by an update to all of the control registers. Then, IOLOCK can be set with a second lock sequence. Note: MPLAB® XC16 provides a built-in C language function for unlocking and modifying the RPCON register: __builtin_write_RPCON(value); For more information, see the MPLAB XC16 Help files. 3.6.9 CONSIDERATIONS FOR PERIPHERAL PIN SELECTION The ability to control Peripheral Pin Selection introduces several considerations into application design that most users would never think of otherwise. This is particularly true for several common peripherals, which are only available as remappable peripherals. The main consideration is that the Peripheral Pin Selects are not available on default pins in the device’s default (Reset) state. More specifically, because all RPINRx registers reset to ‘1’s and RPORx registers reset to ‘0’s, this means all PPS inputs are tied to VSS, while all PPS outputs are disconnected. This means that before any other application code is executed, the user must initialize the device with the proper peripheral configuration. Because the IOLOCK bit resets in the unlocked state, it is not necessary to execute the unlock sequence after the device has come out of Reset. For application safety, however, it is always better to set IOLOCK and lock the configuration after writing to the control registers. The NVMKEY unlock sequence must be executed as an Assembly language routine. If the bulk of the application is written in C, or another high-level language, the unlock sequence should be performed by writing in-line assembly or by using the __builtin_write_RPCON(value) function provided by the compiler. Choosing the configuration requires a review of all Peripheral Pin Selects and their pin assignments, particularly those that will not be used in the application. In all cases, unused pin-selectable peripherals should be disabled completely. Unused peripherals should have their inputs assigned to an unused RPn pin function. I/O pins with unused RPn functions should be configured with the null peripheral output. 3.6.10 INPUT MAPPING The inputs of the Peripheral Pin Select options are mapped on the basis of the peripheral. That is, a control register associated with a peripheral dictates the pin it will be mapped to. The RPINRx registers are used to configure peripheral input mapping. Each register contains sets of 8-bit fields, with each set associated with one of the remappable peripherals. Programming a given peripheral’s bit field with an appropriate 8-bit index value maps the RPn pin with the corresponding value, or internal signal, to that peripheral. See Table 3-31 for a list of available inputs. For example, Figure 3-20 illustrates remappable pin selection for the U1RX input. DS70005319D-page 124  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 3-20: REMAPPABLE INPUT FOR U1RX U1RXR[7:0] 0 VSS 1 CMP1 32 U1RX Input to Peripheral RP32 n RP181 Note: For input only, Peripheral Pin Select functionality does not have priority over TRISx settings. Therefore, when configuring an RPn pin for input, the corresponding bit in the TRISx register must also be configured for input (set to ‘1’). Physical connection to a pin can be made through RP32 through RP71. There are internal signals and virtual pins that can be connected to an input. Table 3-31 shows the details of the input assignment. EXAMPLE 3-2: CONFIGURING UART1 INPUT AND OUTPUT FUNCTIONS // ******************************************* // Unlock Registers //***************************************** __builtin_write_RPCON(0x0000); //***************************************** // Configure Input Functions (See Table 3-32) // Assign U1Rx To Pin RP35 //*************************** _U1RXR = 35; // Assign U1CTS To Pin RP36 //*************************** _U1CTSR = 36; //***************************************** // Configure Output Functions (See Table 3-34) //***************************************** // Assign U1Tx To Pin RP37 //*************************** _RP37 = 1; //*************************** // Assign U1RTS To Pin RP38 //*************************** _RP38 = 2; //***************************************** // Lock Registers //***************************************** __builtin_write_RPCON(0x0800); Example 3-2 provides a configuration for bidirectional communication with flow control using UART1. The following input and output functions are used: • Input Functions: U1RX, U1CTS • Output Functions: U1TX, U1RTS  2017-2019 Microchip Technology Inc. DS70005319D-page 125 dsPIC33CH128MP508 FAMILY TABLE 3-31: MASTER REMAPPABLE PIN INPUTS RPINRx[15:8] or RPINRx[7:0] Function Available on Ports 0 VSS Internal 1 Master Comparator 1 Internal 2 Slave Comparator 1 Internal 3 Slave Comparator 2 Internal 4 Slave Comparator 3 Internal 5 Slave REFCLKO Internal 6 Master PTG Trigger 26 Internal 7 Master PTG Trigger 27 Internal 8 Slave PWM Event Output C Internal 9 Slave PWM Event Output D Internal 10 Slave PWM Event Output E Internal 11 Master PWM Event Output C Internal 12 Master PWM Event Output D Internal 13 Master PWM Event Output E Internal 14-31 RP14-RP31 Reserved 32 RP32 Port Pin RB0 33 RP33 Port Pin RB1 34 RP34 Port Pin RB2 35 RP35 Port Pin RB3 36 RP36 Port Pin RB4 37 RP37 Port Pin RB5 38 RP38 Port Pin RB6 39 RP39 Port Pin RB7 40 RP40 Port Pin RB8 41 RP41 Port Pin RB9 42 RP42 Port Pin RB10 43 RP43 Port Pin RB11 44 RP44 Port Pin RB12 45 RP45 Port Pin RB13 46 RP46 Port Pin RB14 47 RP47 Port Pin RB15 48 RP48 Port Pin RC0 49 RP49 Port Pin RC1 50 RP50 Port Pin RC2 51 RP51 Port Pin RC3 52 RP52 Port Pin RC4 53 RP53 Port Pin RC5 54 RP54 Port Pin RC6 55 RP55 Port Pin RC7 56 RP56 Port Pin RC8 57 RP57 Port Pin RC9 58 RP58 Port Pin RC10 59 RP59 Port Pin RC11 DS70005319D-page 126  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 3-31: MASTER REMAPPABLE PIN INPUTS (CONTINUED) RPINRx[15:8] or RPINRx[7:0] Function Available on Ports 60 RP60 Port Pin RC12 61 RP61 Port Pin RC13 62 RP62 Port Pin RC14 63 RP63 Port Pin RC15 64 RP64 Port Pin RD0 65 RP65 Port Pin RD1 66 RP66 Port Pin RD2 67 RP67 Port Pin RD3 68 RP68 Port Pin RD4 69 RP69 Port Pin RD5 70 RP70 Port Pin RD6 71 RP71 Port Pin RD7 72-167 Reserved Reserved 168 RP168 Slave On Request PWM1 Internal PWM Signal 169 TP169 Slave Off Request PWM1 Internal PWM Signal 170 RP170 Slave Virtual S1RPV0 171 RP171 Slave Virtual S1RPV1 172 RP172 Slave Virtual S1RPV2 173 RP173 Slave Virtual S1RPV3 174 RP174 Slave Virtual S1RPV4 175 RP175 Slave Virtual S1RPV5 176 RP176 Master Virtual RPV0 177 RP177 Master Virtual RPV1 178 RP178 Master Virtual RPV2 179 RP179 Master Virtual RPV3 180 RP180 Master Virtual RPV4 181 RP181 Master Virtual RPV5  2017-2019 Microchip Technology Inc. DS70005319D-page 127 dsPIC33CH128MP508 FAMILY 3.6.11 VIRTUAL CONNECTIONS The dsPIC33CH128MP508 devices support six Master virtual RPn pins (RP176-RP181), which are identical in functionality to all other RPn pins, with the exception of pinouts. These six pins are internal to the devices and are not connected to a physical device pin. These pins provide a simple way for inter-peripheral connection without utilizing a physical pin. For example, the output of the analog comparator can be connected to RP176 and the PWM Fault input can be configured for RP176 as well. This configuration allows the analog comparator to trigger PWM Faults without the use of an actual physical pin on the device. 3.6.12 SLAVE PPS INPUTS TO MASTER CORE PPS The dsPIC33CH128MP508 Slave core subsystem PPS has connections to the Master core subsystem virtual PPS (RPV5-RPV0) output blocks. These inputs are mapped as S1RP175, S1RP174, S1RP173, S1RP172, S1RP171 and S1RP170. The RPn inputs, RP1-RP13, are connected to internal signals from both the Master and Slave core subsystems. Additionally, the Master core virtual output PPS blocks (RPV5-RPV0) are connected to the Slave core PPS circuitry. DS70005319D-page 128 There are virtual pins in PPS to share between Master and Slave: • • • • • • • • • • • • RP181 is for Master input (RPV5) RP180 is for Master input (RPV4) RP179 is for Master input (RPV3) RP178 is for Master input (RPV2) RP177 is for Master input (RPV1) RP176 is for Master input (RPV0) RP175 is for Slave input (S1RPV5) RP174 is for Slave input (S1RPV4) RP173 is for Slave input (S1RPV3) RP172 is for Slave input (S1RPV2) RP171 is for Slave input (S1RPV1) RP170 is for Slave input (S1RPV0) The idea of the RPVn (Remappable Pin Virtual) is to interconnect between the Master and Slave without an I/O pin. For example, the Master UART receiver can be connected to the Slave UART transmit using RPVn and data communication can happen from Slave to Master without using any physical pin.  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 3-32: SELECTABLE INPUT SOURCES (MAPS INPUT TO FUNCTION) Input Name(1) Function Name Register Register Bits External Interrupt 1 INT1 RPINR0 INT1R[7:0] External Interrupt 2 INT2 RPINR1 INT2R[7:0] External Interrupt 3 INT3 RPINR1 INT3R[7:0] Timer1 External Clock T1CK RPINR2 T1CK[7:0] SCCP Timer1 TCKI1 RPINR3 TCKI1R[7:0] SCCP Capture 1 ICM1 RPINR3 ICM1R[7:0] SCCP Timer2 TCKI2 RPINR4 TCKI2R[7:0] SCCP Capture 2 ICM2 RPINR4 ICM2R[7:0] SCCP Timer3 TCKI3 RPINR5 TCKI3R[7:0] SCCP Capture 3 ICM3 RPINR5 ICM3R[7:0] SCCP Timer4 TCKI4 RPINR6 TCKI4R[7:0] SCCP Capture 4 ICM4 RPINR6 ICM4R[7:0] SCCP Timer5 TCKI5 RPINR7 TCKI5R[7:0] SCCP Capture 5 ICM5 RPINR7 ICM5R[7:0] SCCP Timer6 TCKI6 RPINR8 TCKI6R[7:0] SCCP Capture 6 ICM6 RPINR8 ICM6R[7:0] SCCP Timer7 TCKI7 RPINR9 TCKI7R[7:0] SCCP Capture 7 ICM7 RPINR9 ICM7R[7:0] SCCP Timer8 TCKI8 RPINR10 TCKI8R[7:0] SCCP Capture 8 ICM8 RPINR10 ICM8R[7:0] SCCP Fault A OCFA RPINR11 OCFAR[7:0] SCCP Fault B OCFB RPINR11 OCFBR[7:0] PWM PCI Input 8 PCI8 RPINR12 PCI8R[7:0] PWM PCI Input 9 PCI9 RPINR12 PCI9R[7:0] PWM PCI Input 10 PCI10 RPINR13 PCI10R[7:0] PWM PCI Input 11 PCI11 RPINR13 PCI11R[7:0] QEI Input A QEIA1 RPINR14 QEIA1R[7:0] QEI Input B QEIB1 RPINR14 QEIB1R[7:0] QEI Index 1 Input QEINDX1 RPINR15 QEINDX1R[7:0] QEI Home 1 Input QEIHOM1 RPINR15 QEIHOM1R[7:0] UART1 Receive UART1 Data-Set-Ready UART2 Receive U1RX RPINR18 U1RXR[7:0] U1DSR RPINR18 U1DSRR[7:0] U2RX RPINR19 U2RXR[7:0] U2DSRR[7:0] U2DSR RPINR19 SPI1 Data Input SDI1 RPINR20 SDI1R[7:0] SPI1 Clock Input SCK1IN RPINR20 SCK1R[7:0] SPI1 Slave Select SS1 RPINR21 SS1R[7:0] UART2 Data-Set-Ready Reference Clock Input REFOI RPINR21 REFOIR[7:0] SPI2 Data Input SDI2 RPINR22 SDI2R[7:0] SPI2 Clock Input SCK2IN RPINR22 SCK2R[7:0] SS2 RPINR23 SS2R[7:0] U1CTS RPINR23 U1CTSR[7:0] SPI2 Slave Select UART1 Clear-to-Send Note 1: Unless otherwise noted, all inputs use the Schmitt Trigger input buffers.  2017-2019 Microchip Technology Inc. DS70005319D-page 129 dsPIC33CH128MP508 FAMILY TABLE 3-32: SELECTABLE INPUT SOURCES (MAPS INPUT TO FUNCTION) (CONTINUED) Input Name(1) Function Name Register Register Bits CAN1RX RPINR26 CAN1RXR[7:0] UART2 Clear-to-Send U2CTS RPINR30 U2CTSR[7:0] PWM PCI Input 17 PCI17 RPINR37 PCI17R[7:0] PWM PCI Input 18 PCI18 RPINR38 PCI18R[7:0] PWM PCI Input 12 PCI12 RPINR42 PCI12R[7:0] PWM PCI Input 13 PCI13 RPINR42 PCI13R[7:0] PWM PCI Input 14 PCI14 RPINR43 PCI14R[7:0] PWM PCI Input 15 PCI15 RPINR43 PCI15R[7:0] CAN1 Input PWM PCI Input 16 PCI16 RPINR44 PCI16R[7:0] SENT1 Input SENT1 RPINR44 SENT1R[7:0] SENT2 Input SENT2 RPINR45 SENT2R[7:0] CLC Input A CLCINA RPINR45 CLCINAR[7:0] CLC Input B CLCINB RPINR46 CLCINBR[7:0] CLC Input C CLCINC RPINR46 CLCINCR[7:0] CLC Input D CLCIND RPINR47 CLCINDR[7:0] ADC Trigger Input (ADTRIG31) ADCTRG RPINR47 ADCTRGR[7:0] Note 1: Unless otherwise noted, all inputs use the Schmitt Trigger input buffers. DS70005319D-page 130  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.6.13 3.6.14 OUTPUT MAPPING In contrast to inputs, the outputs of the Peripheral Pin Select options are mapped on the basis of the pin. In this case, a control register associated with a particular pin dictates the peripheral output to be mapped. The RPORx registers are used to control output mapping. Each register contains sets of 6-bit fields, with each set associated with one RPn pin (see Register 3-69 through Register 3-91). The value of the bit field corresponds to one of the peripherals and that peripheral’s output is mapped to the pin (see Table 3-34 and Figure 3-21). MAPPING LIMITATIONS The control schema of the peripheral select pins is not limited to a small range of fixed peripheral configurations. There are no mutual or hardware-enforced lockouts between any of the peripheral mapping SFRs. Literally, any combination of peripheral mappings, across any or all of the RPn pins, is possible. This includes both many-to-one and one-to-many mappings of peripheral inputs, and outputs to pins. While such mappings may be technically possible from a configuration point of view, they may not be supportable from an electrical point of view (see Table 3-33). A null output is associated with the output register Reset value of ‘0’. This is done to ensure that remappable outputs remain disconnected from all output pins by default. FIGURE 3-21: MULTIPLEXING REMAPPABLE OUTPUTS FOR RPn RPnR[5:0] Default U1TX Output U1RTS Output 0 1 RP32-RP71 (Physical Pins) 2 Output Data U1DTR Output U2DTR Output 52 53 RP170-RP181 (Internal Virtual Output Ports) Note 1: There are six virtual output ports which are not connected to any I/O ports (RP176-RP181). These virtual ports can be accessed by RPOR20, RPOR21 and RPOR22.  2017-2019 Microchip Technology Inc. DS70005319D-page 131 dsPIC33CH128MP508 FAMILY TABLE 3-33: MASTER REMAPPABLE OUTPUT PIN REGISTERS(1) Register RP Pin I/O Port RPOR0[5:0] RP32 Port Pin RB0 RPOR0[13:8] RP33 Port Pin RB1 RPOR1[5:0] RP34 Port Pin RB2 RPOR1[13:8] RP35 Port Pin RB3 RPOR2[5:0] RP36 Port Pin RB4 RPOR2[13:8] RP37 Port Pin RB5 RPOR3[5:0] RP38 Port Pin RB6 RPOR3[13:8] RP39 Port Pin RB7 RPOR4[5:0] RP40 Port Pin RB8 RPOR4[13:8] RP41 Port Pin RB9 RPOR5[5:0] RP42 Port Pin RB10 RPOR5[13:8] RP43 Port Pin RB11 RPOR6[5:0] RP44 Port Pin RB12 RPOR6[13:8] RP45 Port Pin RB13 RPOR7[5:0] RP46 Port Pin RB14 RPOR7[13:8] RP47 Port Pin RB15 RPOR8[5:0] RP48 Port Pin RC0 RPOR8[13:8] RP49 Port Pin RC1 RPOR9[5:0] RP50 Port Pin RC2 RPOR9[13:8] RP51 Port Pin RC3 RPOR10[5:0] RP52 Port Pin RC4 RPOR10[13:8] RP53 Port Pin RC5 RPOR11[5:0] RP54 Port Pin RC6 RPOR11[13:8] RP55 Port Pin RC7 RPOR12[5:0] RP56 Port Pin RC8 RPOR12[13:8] RP57 Port Pin RC9 RPOR13[5:0] RP58 Port Pin RC10 RPOR13[13:8] RP59 Port Pin RC11 RPOR14[5:0] RP60 Port Pin RC12 RPOR14[13:8] RP61 Port Pin RC13 RPOR15[5:0] RP62 Port Pin RC14 RPOR15[13:8] RP63 Port Pin RC15 RPOR16[5:0] RP64 Port Pin RD0 RPOR16[13:8] RP65 Port Pin RD1 RPOR17[5:0] RP66 Port Pin RD2 RPOR17[13:8] RP67 Port Pin RD3 RPOR18[5:0] RP68 Port Pin RD4 RPOR18[13:8] RP69 Port Pin RD5 RPOR19[5:0] RP70 Port Pin RD6 RPOR19[13:8] RP71 Port Pin RD7 RPOR20[5:0] RP176 Virtual Pin RPV0 RPOR20[13:8] RP177 Virtual Pin RPV1 RPOR21[5:0] RP178 Virtual Pin RPV2 RPOR21[13:8] RP179 Virtual Pin RPV3 RPOR22[5:0] RP180 Virtual Pin RPV4 RPOR22[13:8] RP181 Virtual Pin RPV5 Note 1: Not all RP pins are available on all packages. Make sure the selected device variant has the feature available on the device. DS70005319D-page 132  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 3-34: Function OUTPUT SELECTION FOR REMAPPABLE PINS (RPn)(1) RPnR[5:0] Output Name Default PORT 0 RPn tied to Default Pin U1TX 1 RPn tied to UART1 Transmit U1RTS 2 RPn tied to UART1 Request-to-Send U2TX 3 RPn tied to UART2 Transmit U2RTS 4 RPn tied to UART2 Request-to-Send SDO1 5 RPn tied to SPI1 Data Output SCK1 6 RPn tied to SPI1 Clock Output SS1 7 RPn tied to SPI1 Slave Select SDO2 8 RPn tied to SPI2 Data Output SCK2 9 RPn tied to SPI2 Clock Output SS2 10 RPn tied to SPI2 Slave Select REFCLKO 14 RPn tied to Reference Clock Output OCM1 15 RPn tied to SCCP1 Output OCM2 16 RPn tied to SCCP2 Output OCM3 17 RPn tied to SCCP3 Output OCM4 18 RPn tied to SCCP4 Output OCM5 19 RPn tied to SCCP5 Output OCM6 20 RPn tied to SCCP6 Output CAN1 21 RPn tied to CAN1 Output CMP1 23 RPn tied to Comparator 1 Output PWM4H 34 RPn tied to PWM4H Output PWM4L 35 RPn tied to PWM4L Output PWMEA 36 RPn tied to PWM Event A Output PWMEB 37 RPn tied to PWM Event B Output QEICMP 38 RPn tied to QEI Comparator Output CLC1OUT 40 RPn tied to CLC1 Output CLC2OUT 41 RPn tied to CLC2 Output OCM7 42 RPn tied to SCCP7 Output OCM8 43 RPn tied to SCCP8 Output PWMEC 44 RPn tied to PWM Event C Output PWMED 45 RPn tied to PWM Event D Output PTGTRG24 46 PTG Trigger Output 24 PTGTRG25 47 PTG Trigger Output 25 SENT1OUT 48 RPn tied to SENT1 Output SENT2OUT 49 RPn tied to SENT2 Output CLC3OUT 50 RPn tied to CLC3 Output CLC4OUT 51 RPn tied to CLC4 Output U1DTR 52 Data Terminal Ready Output 1 53 Data Terminal Ready Output 2 U2DTR Note 1: Not all RP are available on all packages. Make sure the selected device variant has the feature available on the device.  2017-2019 Microchip Technology Inc. DS70005319D-page 133 dsPIC33CH128MP508 FAMILY 3.6.15 1. 2. I/O HELPFUL TIPS In some cases, certain pins, as defined in Table 24-18 under “Injection Current”, have internal protection diodes to VDD and VSS. The term, “Injection Current”, is also referred to as “Clamp Current”. On designated pins, with sufficient external current-limiting precautions by the user, I/O pin input voltages are allowed to be greater or lesser than the data sheet absolute maximum ratings, with respect to the VSS and VDD supplies. Note that when the user application forward biases either of the high or low-side internal input clamp diodes, that the resulting current being injected into the device that is clamped internally by the VDD and VSS power rails, may affect the ADC accuracy by four to six counts. I/O pins that are shared with any analog input pin (i.e., ANx) are always analog pins, by default, after any Reset. Consequently, configuring a pin as an analog input pin automatically disables the digital input pin buffer and any attempt to read the digital input level by reading PORTx or LATx will always return a ‘0’, regardless of the digital logic level on the pin. To use a pin as a digital I/O pin on a shared ANx pin, the user application needs to configure the Analog Select for PORTx registers in the I/O ports module (i.e., ANSELx) by setting the appropriate bit that corresponds to that I/O port pin to a ‘0’. Note: Although it is not possible to use a digital input pin when its analog function is enabled, it is possible to use the digital I/O output function, TRISx = 0x0, while the analog function is also enabled. However, this is not recommended, particularly if the analog input is connected to an external analog voltage source, which would create signal contention between the analog signal and the output pin driver. DS70005319D-page 134 3. 4. 5. Most I/O pins have multiple functions. Referring to the device pin diagrams in this data sheet, the priorities of the functions allocated to any pins are indicated by reading the pin name, from left-to-right. The left most function name takes precedence over any function to its right in the naming convention. For example: AN14/ISRC1/RP50/RC2; this indicates that AN14 is the highest priority in this example and will supersede all other functions to its right in the list. Those other functions to its right, even if enabled, would not work as long as any other function to its left was enabled. This rule applies to all of the functions listed for a given pin. Each pin has an internal weak pull-up resistor and pull-down resistor that can be configured using the CNPUx and CNPDx registers, respectively. These resistors eliminate the need for external resistors in certain applications. The internal pull-up is up to ~(VDD – 0.8), not VDD. This value is still above the minimum VIH of CMOS and TTL devices. When driving LEDs directly, the I/O pin can source or sink more current than what is specified in the VOH/IOH and VOL/IOL DC characteristics specification. The respective IOH and IOL current rating only applies to maintaining the corresponding output at or above the VOH, and at or below the VOL levels. However, for LEDs, unlike digital inputs of an externally connected device, they are not governed by the same minimum VIH/VIL levels. An I/O pin output can safely sink or source any current less than that listed in the Absolute Maximum Ratings in Section 24.0 “Electrical Characteristics” of this data sheet. For example: VOH = 2.4v @ IOH = -8 mA and VDD = 3.3V The maximum output current sourced by any 8 mA I/O pin = 12 mA. LED source current < 12 mA is technically permitted. Refer to the VOH/IOH graphs in Section 24.1 “DC Characteristics” for additional information.  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 6. The Peripheral Pin Select (PPS) pin mapping rules are as follows: a) Only one “output” function can be active on a given pin at any time, regardless if it is a dedicated or remappable function (one pin, one output). b) It is possible to assign a “remappable output” function to multiple pins and externally short or tie them together for increased current drive. c) If any “dedicated output” function is enabled on a pin, it will take precedence over any remappable “output” function. d) If any “dedicated digital” (input or output) function is enabled on a pin, any number of “input” remappable functions can be mapped to the same pin. e) If any “dedicated analog” function(s) are enabled on a given pin, “digital input(s)” of any kind will all be disabled, although a single “digital output”, at the user’s cautionary discretion, can be enabled and active as long as there is no signal contention with an external analog input signal. For example, it is possible for the ADC to convert the digital output logic level, or to toggle a digital output on a comparator or ADC input, provided there is no external analog input, such as for a built-in self-test. f) Any number of “input” remappable functions can be mapped to the same pin(s) at the same time, including to any pin with a single output from either a dedicated or remappable “output”. g) The TRISx registers control only the digital I/O output buffer. Any other dedicated or remappable active “output” will automatically override the TRISx setting. The TRISx register does not control the digital logic “input” buffer. Remappable digital “inputs” do not automatically override TRISx settings, which means that the TRISx bit must be set to input for pins with only remappable input function(s) assigned. h) All analog pins are enabled by default after any Reset and the corresponding digital input buffer on the pin has been disabled. Only the Analog Select for PORTx (ANSELx) registers control the digital input buffer, not the TRISx register. The user must disable the analog function on a pin using the Analog Select for PORTx registers in order to use any “digital input(s)” on a corresponding pin, no exceptions.  2017-2019 Microchip Technology Inc. 3.6.16 I/O PORTS RESOURCES Many useful resources are provided on the main product page of the Microchip website for the devices listed in this data sheet. This product page contains the latest updates and additional information. 3.6.16.1 Key Resources • “I/O Ports with Edge Detect” (www.microchip.com/DS70005322) in the “dsPIC33/PIC24 Family Reference Manual” • Code Samples • Application Notes • Software Libraries • Webinars • All Related “dsPIC33/PIC24 Family Reference Manual” Sections • Development Tools DS70005319D-page 135 PORTA REGISTER SUMMARY ANSELA — — — — — — — — — — — ANSELA[4:0] TRISA — — — — — — — — — — — TRISA[4:0] PORTA — — — — — — — — — — — RA[4:0] LATA — — — — — — — — — — — LATA[4:0] ODCA — — — — — — — — — — — ODCA[4:0] CNPUA — — — — — — — — — — — CNPUA[4:0] CNPDA — — — — — — — — — — — CNCONA ON — — — CNSTYLE — — — — — — CNEN0A — — — — — — — — — — — CNEN0A[4:0] CNSTATA — — — — — — — — — — — CNSTATA[4:0] CNEN1A — — — — — — — — — — — CNEN1A[4:0] CNFA — — — — — — — — — — — CNFA[4:0] TABLE 3-36: ANSELB — — — — — — — — ANSELB[9:7] — — — — — — ANSELB[3:0] TRISB[15:0] PORTB RB[15:0] LATB LATB[15:0] ODCB ODCB[15:0] CNPUB CNPUB[15:0] CNPDB CNPDB[15:0] ON — — — CNSTYLE — — —  2017-2019 Microchip Technology Inc. CNEN0B CNEN0[15:0] CNSTATB CNSTATB[15:0] CNEN1B CNEN1B[15:0] CNFB — PORTB REGISTER SUMMARY — TRISB CNCONB CNPDA[4:0] — CNFB[15:0] — — — — — dsPIC33CH128MP508 FAMILY DS70005319D-page 136 TABLE 3-35:  2017-2019 Microchip Technology Inc. TABLE 3-37: ANSELC PORTC REGISTER SUMMARY — — — — — — — ANSELC[8:7] TRISC PORTC — — — ANSELC[3:0] ODCC[15:0] CNPUC CNPUC[15:0] CNPDC CNPDC[15:0] CNCONC ON — — — CNSTYLE — — — — CNEN0C CNEN0C[15:0] CNSTATC CNSTATC[15:0] CNEN1C CNEN1C[15:0] CNFC — — — — CNFC[15:0] PORTD REGISTER SUMMARY — — — — — ANSEL10 — TRISD — — — — — — — — — — — — — — — — — TRISD[15:0] PORTD RD[15:0] LATD LATD[15:0] ODCD ODCD[15:0] CNPUD CNPUD[15:0] CNPDD CNPDD[15:0] ON — — — CNSTYLE — — — CNEN0D CNEN0D[15:0] CNSTATD CNSTATD[15:0] CNEN1D CNEN1D[15:0] CNFD[15:0] DS70005319D-page 137 dsPIC33CH128MP508 FAMILY TABLE 3-38: CNFD — LATC[15:0] ODCC CNCOND — RC[15:0] LATC ANSELD — TRISC[15:0] ANSLE PORTE REGISTER SUMMARY — — — — — — — TRISE PORTE — — — — — — — — — — — — — — — — RE[15:0] LATE LATE[15:0] ODCE ODCE[15:0] CNPUE CNPUE[15:0] CNPDE CNCONE — TRISE[15:0] CNPDE[15:0] ON — — — CNSTYLE — — — CNEN0E CNEN0E[15:0] CNSTATE CNSTATE[15:0] CNEN1E CNEN1E[15:0] CNFE CNFE[15:0] dsPIC33CH128MP508 FAMILY DS70005319D-page 138 TABLE 3-39:  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.6.17 PERIPHERAL PIN SELECT REGISTERS REGISTER 3-36: RPCON: PERIPHERAL REMAPPING CONFIGURATION REGISTER(1) U-0 U-0 U-0 U-0 R/W-0 U-0 U-0 U-0 — — — — IOLOCK — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-12 Unimplemented: Read as ‘0’ bit 11 IOLOCK: Peripheral Remapping Register Lock bit 1 = All Peripheral Remapping registers are locked and cannot be written 0 = All Peripheral Remapping registers are unlocked and can be written bit 10-0 Unimplemented: Read as ‘0’ Note 1: Writing to this register needs an unlock sequence. REGISTER 3-37: RPINR0: PERIPHERAL PIN SELECT INPUT REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INT1R7 INT1R6 INT1R5 INT1R4 INT1R3 INT1R2 INT1R1 INT1R0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 INT1R[7:0]: Assign External Interrupt 1 (INT1) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. DS70005319D-page 139 dsPIC33CH128MP508 FAMILY REGISTER 3-38: RPINR1: PERIPHERAL PIN SELECT INPUT REGISTER 1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INT3R7 INT3R6 INT3R5 INT3R4 INT3R3 INT3R2 INT3R1 INT3R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INT2R7 INT2R6 INT2R5 INT2R4 INT2R3 INT2R2 INT2R1 INT2R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 INT3R[7:0]: Assign External Interrupt 3 (INT3) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 INT2R[7:0]: Assign External Interrupt 2 (INT2) to the Corresponding RPn Pin bits See Table 3-31. REGISTER 3-39: RPINR2: PERIPHERAL PIN SELECT INPUT REGISTER 2 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 T1CKR7 T1CKR6 T1CKR5 T1CKR4 T1CKR3 T1CKR2 T1CKR1 T1CKR0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 T1CKR[7:0]: Assign Timer1 External Clock (T1CK) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 Unimplemented: Read as ‘0’ DS70005319D-page 140  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-40: RPINR3: PERIPHERAL PIN SELECT INPUT REGISTER 3 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ICM1R7 ICM1R6 ICM1R5 ICM1R4 ICM1R3 ICM1R2 ICM1R1 ICM1R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TCKI1R7 TCKI1R6 TCKI1R5 TCKI1R4 TCKI1R3 TCKI1R2 TCKI1R1 TCKI1R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 ICM1R[7:0]: Assign SCCP Capture 1 (ICM1) Input to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 TCKI1[7:0]: Assign SCCP Timer1 (TCKI1) Input to the Corresponding RPn Pin bits See Table 3-31. REGISTER 3-41: RPINR4: PERIPHERAL PIN SELECT INPUT REGISTER 4 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ICM2R7 ICM2R6 ICM2R5 ICM2R4 ICM2R3 ICM2R2 ICM2R1 ICM2R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TCKI2R7 TCKI2R6 TCKI2R5 TCKI2R4 TCKI2R3 TCKI2R2 TCKI2R1 TCKI2R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 ICM2R[7:0]: Assign SCCP Capture 2 (ICM2) Input to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 TCKI2R[7:0]: Assign SCCP Timer2 (TCKI2) Input to the Corresponding RPn Pin bits See Table 3-31.  2017-2019 Microchip Technology Inc. DS70005319D-page 141 dsPIC33CH128MP508 FAMILY REGISTER 3-42: RPINR5: PERIPHERAL PIN SELECT INPUT REGISTER 5 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ICM3R7 ICM3R6 ICM3R5 ICM3R4 ICM3R3 ICM3R2 ICM3R1 ICM3R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TCKI3R7 TCKI3R6 TCKI3R5 TCKI3R4 TCKI3R3 TCKI3R2 TCKI3R1 TCKI3R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 ICM3R[7:0]: Assign SCCP Capture 3 (ICM3) Input to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 TCKI3R[7:0]: Assign SCCP Timer3 (TCKI3) Input to the Corresponding RPn Pin bits See Table 3-31. REGISTER 3-43: RPINR6: PERIPHERAL PIN SELECT INPUT REGISTER 6 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ICM4R7 ICM4R6 ICM4R5 ICM4R4 ICM4R3 ICM4R2 ICM4R1 ICM4R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TCKI4R7 TCKI4R6 TCKI4R5 TCKI4R4 TCKI4R3 TCKI4R2 TCKI4R1 TCKI4R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 ICM4R[7:0]: Assign SCCP Capture 4 (ICM4) Input to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 TCKI4R[7:0]: Assign SCCP Timer4 (TCKI4) Input to the Corresponding RPn Pin bits See Table 3-31. DS70005319D-page 142  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-44: RPINR7: PERIPHERAL PIN SELECT INPUT REGISTER 7 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ICM5R7 ICM5R6 ICM5R5 ICM5R4 ICM5R3 ICM5R2 ICM5R1 ICM5R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TCKI5R7 TCKI5R6 TCKI5R5 TCKI5R4 TCKI5R3 TCKI5R2 TCKI5R1 TCKI5R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 ICM5R[7:0]: Assign SCCP Capture 5 (ICM5) Input to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 TCKI5R[7:0]: Assign SCCP Timer5 (TCKI5) Input to the Corresponding RPn Pin bits See Table 3-31. REGISTER 3-45: RPINR8: PERIPHERAL PIN SELECT INPUT REGISTER 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ICM6R7 ICM6R6 ICM6R5 ICM6R4 ICM6R3 ICM6R2 ICM6R1 ICM6R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TCKI6R7 TCKI6R6 TCKI6R5 TCKI6R4 TCKI6R3 TCKI6R2 TCKI6R1 TCKI6R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 ICM6R[7:0]: Assign SCCP Capture 6 (ICM6) Input to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 TCKI6R[7:0]: Assign SCCP Timer6 (TCKI6) Input to the Corresponding RPn Pin bits See Table 3-31.  2017-2019 Microchip Technology Inc. DS70005319D-page 143 dsPIC33CH128MP508 FAMILY REGISTER 3-46: RPINR9: PERIPHERAL PIN SELECT INPUT REGISTER 9 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ICM7R7 ICM7R6 ICM7R5 ICM7R4 ICM7R3 ICM7R2 ICM7R1 ICM7R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TCKI7R7 TCKI7R6 TCKI7R5 TCKI7R4 TCKI7R3 TCKI7R2 TCKI7R1 TCKI7R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 ICM7R[7:0]: Assign SCCP Capture 7 (ICM7) Input to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 TCKI7R[7:0]: Assign SCCP Timer7 (TCKI7) Input to the Corresponding RPn Pin bits See Table 3-31. REGISTER 3-47: RPINR10: PERIPHERAL PIN SELECT INPUT REGISTER 10 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ICM8R7 ICM8R6 ICM8R5 ICM8R4 ICM8R3 ICM8R2 ICM8R1 ICM8R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TCKI8R7 TCKI8R6 TCKI8R5 TCKI8R4 TCKI8R3 TCKI8R2 TCKI8R1 TCKI8R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 ICM8R[7:0]: Assign SCCP Capture 8 (ICM8) Input to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 TCKI8R[7:0]: Assign SCCP Timer8 (TCKI8) Input to the Corresponding RPn Pin bits See Table 3-31. DS70005319D-page 144  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-48: RPINR11: PERIPHERAL PIN SELECT INPUT REGISTER 11 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 OCFBR7 OCFBR6 OCFBR5 OCFBR4 OCFBR3 OCFBR2 OCFBR1 OCFBR0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 OCFAR7 OCFAR6 OCFAR5 OCFAR4 OCFAR3 OCFAR2 OCFAR1 OCFAR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 OCFBR[7:0]: Assign SCCP Fault B (OCFB) Input to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 OCFAR[7:0]: Assign SCCP Fault A (OCFA) Input to the Corresponding RPn Pin bits See Table 3-31. REGISTER 3-49: RPINR12: PERIPHERAL PIN SELECT INPUT REGISTER 12 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI9R7 PCI9R6 PCI9R5 PCI9R4 PCI9R3 PCI9R2 PCI9R1 PCI9R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI8R7 PCI8R6 PCI8R5 PCI8R4 PCI8R3 PCI8R2 PCI8R1 PCI8R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 PCI9R[7:0]: Assign PWM Input 9 (PCI9) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 PCI8R[7:0]: Assign PWM Input 8 (PCI8) to the Corresponding RPn Pin bits See Table 3-31.  2017-2019 Microchip Technology Inc. DS70005319D-page 145 dsPIC33CH128MP508 FAMILY REGISTER 3-50: RPINR13: PERIPHERAL PIN SELECT INPUT REGISTER 13 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI11R7 PCI11R6 PCI11R5 PCI11R4 PCI11R3 PCI11R2 PCI11R1 PCI11R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI10R7 PCI10R6 PCI10R5 PCI10R4 PCI10R3 PCI10R2 PCI10R1 PCI10R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 PCI11R[7:0]: Assign PWM Input 11 (PCI11) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 PCI10R[7:0]: Assign PWM Input 10 (PCI10) to the Corresponding RPn Pin bits See Table 3-31. REGISTER 3-51: RPINR14: PERIPHERAL PIN SELECT INPUT REGISTER 14 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 QEIB1R7 QEIB1R6 QEIB1R5 QEIB1R4 QEIB1R3 QEIB1R2 QEIB1R1 QEIB1R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 QEIA1R7 QEIA1R6 QEIA1R5 QEIA1R4 QEIA1R3 QEIA1R2 QEIA1R1 QEIA1R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 QEIB1R[7:0]: Assign QEI Input B (QEIB1) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 QEIA1R[7:0]: Assign QEI Input A (QEIA1) to the Corresponding RPn Pin bits See Table 3-31. DS70005319D-page 146  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-52: R/W-0 QEIHOM1R7 RPINR15: PERIPHERAL PIN SELECT INPUT REGISTER 15 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 QEIHOM1R6 QEIHOM1R5 QEIHOM1R4 QEIHOM1R3 QEIHOM1R2 QEIHOM1R1 QEIHOM1R0 bit 15 bit 8 R/W-0 QEINDX1R7 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 QEINDX1R6 QEINDX1R5 QEINDX1R4 QEINDX1R3 QEINDX1R2 R/W-0 R/W-0 QEINDX1R1 QEINDX1R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 QEIHOM1R[7:0]: Assign QEI Home 1 Input (QEIHOM1) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 QEINDX1R[7:0]: Assign QEI Index 1 Input (QEINDX1) to the Corresponding RPn Pin bits See Table 3-31. REGISTER 3-53: RPINR18: PERIPHERAL PIN SELECT INPUT REGISTER 18 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U1DSRR7 U1DSRR6 U1DSRR5 U1DSRR4 U1DSRR3 U1DSRR2 U1DSRR1 U1DSRR0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U1RXR7 U1RXR6 U1RXR5 U1RXR4 U1RXR3 U1RXR2 U1RXR1 U1RXR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 U1DSRR[7:0]: Assign UART1 Data-Set-Ready (U1DSR) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 U1RXR[7:0]: Assign UART1 Receive (U1RX) to the Corresponding RPn Pin bits See Table 3-31.  2017-2019 Microchip Technology Inc. DS70005319D-page 147 dsPIC33CH128MP508 FAMILY REGISTER 3-54: RPINR19: PERIPHERAL PIN SELECT INPUT REGISTER 19 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U2DSRR7 U2DSRR6 U2DSRR5 U2DSRR4 U2DSRR3 U2DSRR2 U2DSRR1 U2DSRR0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U2RXR7 U2RXR6 U2RXR5 U2RXR4 U2RXR3 U2RXR2 U2RXR1 U2RXR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 U2DSRR[7:0]: Assign UART2 Data-Set-Ready (U2DSR) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 U2RXR[7:0]: Assign UART2 Receive (U2RX) to the Corresponding RPn Pin bits See Table 3-31. REGISTER 3-55: RPINR20: PERIPHERAL PIN SELECT INPUT REGISTER 20 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SCK1R7 SCK1R6 SCK1R5 SCK1R4 SCK1R3 SCK1R2 SCK1R1 SCK1R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SDI1R7 SDI1R6 SDI1R5 SDI1R4 SDI1R3 SDI1R2 SDI1R1 SDI1R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 SCK1R[7:0]: Assign SPI1 Clock Input (SCK1IN) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 SDI1R[7:0]: Assign SPI1 Data Input (SDI1) to the Corresponding RPn Pin bits See Table 3-31. DS70005319D-page 148  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-56: RPINR21: PERIPHERAL PIN SELECT INPUT REGISTER 21 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 REFOIR7 REFOIR6 REFOIR5 REFOIR4 REFOIR3 REFOIR2 REFOIR1 REFOIR0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SS1R7 SS1R6 SS1R5 SS1R4 SS1R3 SS1R2 SS1R1 SS1R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 REFOIR[7:0]: Assign Reference Clock Input (REFOI) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 SS1R[7:0]: Assign SPI1 Slave Select (SS1) to the Corresponding RPn Pin bits See Table 3-31. REGISTER 3-57: RPINR22: PERIPHERAL PIN SELECT INPUT REGISTER 22 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SCK2R7 SCK2R6 SCK2R5 SCK2R4 SCK2R3 SCK2R2 SCK2R1 SCK2R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SDI2R7 SDI2R6 SDI2R5 SDI2R4 SDI2R3 SDI2R2 SDI2R1 SDI2R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 SCK2R[7:0]: Assign SPI2 Clock Input (SCK2IN) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 SDI2R[7:0]: Assign SPI2 Data Input (SDI2) to the Corresponding RPn Pin bits See Table 3-31.  2017-2019 Microchip Technology Inc. DS70005319D-page 149 dsPIC33CH128MP508 FAMILY REGISTER 3-58: RPINR23: PERIPHERAL PIN SELECT INPUT REGISTER 23 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U1CTSR7 U1CTSR6 U1CTSR5 U1CTSR4 U1CTSR3 U1CTSR2 U1CTSR1 U1CTSR0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SS2R7 SS2R6 SS2R5 SS2R4 SS2R3 SS2R2 SS2R1 SS2R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 U1CTSR[7:0]: Assign UART1 Clear-to-Send (U1CTS) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 SS2R[7:0]: Assign SPI2 Slave Select (SS2) to the Corresponding RPn Pin bits See Table 3-31. REGISTER 3-59: RPINR26: PERIPHERAL PIN SELECT INPUT REGISTER 26 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-0 R/W-0 CAN1RXR7 CAN1RXR6 R/W-0 R/W-0 R/W-0 CAN1RXR5 CAN1RXR4 CAN1RXR3 R/W-0 R/W-0 R/W-0 CAN1RXR2 CAN1RXR1 CAN1RXR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7-0 CAN1RXR[7:0]: Assign CAN1 Input (CAN1RX) to the Corresponding RPn Pin bits See Table 3-31. DS70005319D-page 150  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-60: RPINR30: PERIPHERAL PIN SELECT INPUT REGISTER 30 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U2CTSR7 U2CTSR6 U2CTSR5 U2CTSR4 U2CTSR3 U2CTSR2 U2CTSR1 U2CTSR0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 U2CTSR[7:0]: Assign UART2 Clear-to-Send (U2CTS) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 Unimplemented: Read as ‘0’ REGISTER 3-61: RPINR37: PERIPHERAL PIN SELECT INPUT REGISTER 37 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI17R7 PCI17R6 PCI17R5 PCI17R4 PCI17R3 PCI17R2 PCI17R1 PCI17R0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 PCI17R[7:0]: Assign PWM Input 17 (PCI17) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. DS70005319D-page 151 dsPIC33CH128MP508 FAMILY REGISTER 3-62: RPINR38: PERIPHERAL PIN SELECT INPUT REGISTER 38 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI18R7 PCI18R6 PCI18R5 PCI18R4 PCI18R3 PCI18R2 PCI18R1 PCI18R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7-0 PCI18R[7:0]: Assign PWM Input 18 (PCI18) to the Corresponding RPn Pin bits See Table 3-31. REGISTER 3-63: RPINR42: PERIPHERAL PIN SELECT INPUT REGISTER 42 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI13R7 PCI13R6 PCI13R5 PCI13R4 PCI13R3 PCI13R2 PCI13R1 PCI13R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI12R7 PCI12R6 PCI12R5 PCI12R4 PCI12R3 PCI12R2 PCI12R1 PCI12R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 PCI13R[7:0]: Assign PWM Input 13 (PCI13) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 PCI12R[7:0]: Assign PWM Input 12 (PCI12) to the Corresponding RPn Pin bits See Table 3-31. DS70005319D-page 152  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-64: RPINR43: PERIPHERAL PIN SELECT INPUT REGISTER 43 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI15R7 PCI15R6 PCI15R5 PCI15R4 PCI15R3 PCI15R2 PCI15R1 PCI15R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI14R7 PCI14R6 PCI14R5 PCI14R4 PCI14R3 PCI14R2 PCI14R1 PCI14R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 PCI15R[7:0]: Assign PWM Input 15 (PCI15) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 PCI14R[7:0]: Assign PWM Input 14 (PCI14) to the Corresponding RPn Pin bits See Table 3-31. REGISTER 3-65: RPINR44: PERIPHERAL PIN SELECT INPUT REGISTER 44 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SENT1R7 SENT1R6 SENT1R5 SENT1R4 SENT1R3 SENT1R2 SENT1R1 SENT1R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI16R7 PCI16R6 PCI16R5 PCI16R4 PCI16R3 PCI16R2 PCI16R1 PCI16R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 SENT1R[7:0]: Assign SENT1 Input (SENT1) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 PCI16[7:0]: Assign PWM Input 16 (PCI16) to the Corresponding RPn Pin bits See Table 3-31.  2017-2019 Microchip Technology Inc. DS70005319D-page 153 dsPIC33CH128MP508 FAMILY REGISTER 3-66: RPINR45: PERIPHERAL PIN SELECT INPUT REGISTER 45 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CLCINAR7 CLCINAR6 CLCINAR5 CLCINAR4 CLCINAR3 CLCINAR2 CLCINAR1 CLCINAR0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SENT2R7 SENT2R6 SENT2R5 SENT2R4 SENT2R3 SENT2R2 SENT2R1 SENT2R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 CLCINAR[7:0]: Assign CLC Input A (CLCINA) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 SENT2R[7:0]: Assign SENT2 Input (SENT2) to the Corresponding RPn Pin bits See Table 3-31. REGISTER 3-67: RPINR46: PERIPHERAL PIN SELECT INPUT REGISTER 46 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CLCINCR7 CLCINCR6 CLCINCR5 CLCINCR4 CLCINCR3 CLCINCR2 CLCINCR1 CLCINCR0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CLCINBR7 CLCINBR6 CLCINBR5 CLCINBR4 CLCINBR3 CLCINBR2 CLCINBR1 CLCINBR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 CLCINCR[7:0]: Assign CLC Input C (CLCINC) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 CLCINBR[7:0]: Assign CLC Input B (CLCINB) to the Corresponding RPn Pin bits See Table 3-31. DS70005319D-page 154  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-68: R/W-0 ADCTRGR7 RPINR47: PERIPHERAL PIN SELECT INPUT REGISTER 47 R/W-0 R/W-0 R/W-0 R/W-0 ADCTRGR6 ADCTRGR5 ADCTRGR4 ADCTRGR3 R/W-0 ADCTRGR2 R/W-0 R/W-0 ADCTRGR1 ADCTRGR0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CLCINDR7 CLCINDR6 CLCINDR5 CLCINDR4 CLCINDR3 CLCINDR2 CLCINDR1 CLCINDR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 ADCTRGR[7:0]: Assign ADC Trigger Input (ADCTRG) to the Corresponding RPn Pin bits See Table 3-31. bit 7-0 CLCINDR[7:0]: Assign CLC Input D (CLCIND) to the Corresponding RPn Pin bits See Table 3-31.  2017-2019 Microchip Technology Inc. DS70005319D-page 155 dsPIC33CH128MP508 FAMILY REGISTER 3-69: RPOR0: PERIPHERAL PIN SELECT OUTPUT REGISTER 0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP33R5 RP33R4 RP33R3 RP33R2 RP33R1 RP33R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP32R5 RP32R4 RP32R3 RP32R2 RP32R1 RP32R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP33R[5:0]: Peripheral Output Function is Assigned to RP33 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP32R[5:0]: Peripheral Output Function is Assigned to RP32 Output Pin bits (see Table 3-34 for peripheral function numbers) REGISTER 3-70: RPOR1: PERIPHERAL PIN SELECT OUTPUT REGISTER 1 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP35R5 RP35R4 RP35R3 RP35R2 RP35R1 RP35R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP34R5 RP34R4 RP34R3 RP34R2 RP34R1 RP34R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP35R[5:0]: Peripheral Output Function is Assigned to RP35 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP34R[5:0]: Peripheral Output Function is Assigned to RP34 Output Pin bits (see Table 3-34 for peripheral function numbers) DS70005319D-page 156  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-71: RPOR2: PERIPHERAL PIN SELECT OUTPUT REGISTER 2 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP37R5 RP37R4 RP37R3 RP37R2 RP37R1 RP37R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP36R5 RP36R4 RP36R3 RP36R2 RP36R1 RP36R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP37R[5:0]: Peripheral Output Function is Assigned to RP37 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP36R[5:0]: Peripheral Output Function is Assigned to RP36 Output Pin bits (see Table 3-34 for peripheral function numbers) REGISTER 3-72: RPOR3: PERIPHERAL PIN SELECT OUTPUT REGISTER 3 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP39R5 RP39R4 RP39R3 RP39R2 RP39R1 RP39R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP38R5 RP38R5 RP38R5 RP38R5 RP38R5 RP38R5 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP39R[5:0]: Peripheral Output Function is Assigned to RP39 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP38R[5:0]: Peripheral Output Function is Assigned to RP38 Output Pin bits (see Table 3-34 for peripheral function numbers)  2017-2019 Microchip Technology Inc. DS70005319D-page 157 dsPIC33CH128MP508 FAMILY REGISTER 3-73: RPOR4: PERIPHERAL PIN SELECT OUTPUT REGISTER 4 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP41R5 RP41R4 RP41R3 RP41R2 RP41R1 RP41R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP40R5 RP40R4 RP40R3 RP40R2 RP40R1 RP40R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP41R[5:0]: Peripheral Output Function is Assigned to RP41 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP40R[5:0]: Peripheral Output Function is Assigned to RP40 Output Pin bits (see Table 3-34 for peripheral function numbers) REGISTER 3-74: RPOR5: PERIPHERAL PIN SELECT OUTPUT REGISTER 5 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP43R5 RP43R4 RP43R3 RP43R2 RP43R1 RP43R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP42R5 RP42R4 RP42R3 RP42R2 RP42R1 RP42R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP43R[5:0]: Peripheral Output Function is Assigned to RP43 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP42R[5:0]: Peripheral Output Function is Assigned to RP42 Output Pin bits (see Table 3-34 for peripheral function numbers) DS70005319D-page 158  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-75: RPOR6: PERIPHERAL PIN SELECT OUTPUT REGISTER 6 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP45R5 RP45R4 RP45R3 RP45R2 RP45R1 RP45R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP44R5 RP44R4 RP44R3 RP44R2 RP44R1 RP44R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP45R[5:0]: Peripheral Output Function is Assigned to RP45 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP44R[5:0]: Peripheral Output Function is Assigned to RP44 Output Pin bits (see Table 3-34 for peripheral function numbers) REGISTER 3-76: RPOR7: PERIPHERAL PIN SELECT OUTPUT REGISTER 7 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP47R5 RP47R4 RP47R3 RP47R2 RP47R1 RP47R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP46R5 RP46R4 RP46R3 RP46R2 RP46R1 RP46R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP47R[5:0]: Peripheral Output Function is Assigned to RP47 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP46R[5:0]: Peripheral Output Function is Assigned to RP46 Output Pin bits (see Table 3-34 for peripheral function numbers)  2017-2019 Microchip Technology Inc. DS70005319D-page 159 dsPIC33CH128MP508 FAMILY REGISTER 3-77: RPOR8: PERIPHERAL PIN SELECT OUTPUT REGISTER 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP49R5 RP49R4 RP49R3 RP49R2 RP49R1 RP49R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP48R5 RP48R4 RP48R3 RP48R2 RP48R1 RP48R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP49R[5:0]: Peripheral Output Function is Assigned to RP49 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP48R[5:0]: Peripheral Output Function is Assigned to RP48 Output Pin bits (see Table 3-34 for peripheral function numbers) REGISTER 3-78: RPOR9: PERIPHERAL PIN SELECT OUTPUT REGISTER 9 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP51R5 RP51R4 RP51R3 RP51R2 RP51R1 RP51R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP50R5 RP50R4 RP50R3 RP50R2 RP50R1 RP50R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP51R[5:0]: Peripheral Output Function is Assigned to RP51 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP50R[5:0]: Peripheral Output Function is Assigned to RP50 Output Pin bits (see Table 3-34 for peripheral function numbers) DS70005319D-page 160  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-79: RPOR10: PERIPHERAL PIN SELECT OUTPUT REGISTER 10 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP53R5 RP53R4 RP53R3 RP53R2 RP53R1 RP53R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP52R5 RP52R4 RP52R3 RP52R2 RP52R1 RP52R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP53[5:0]: Peripheral Output Function is Assigned to RP53 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP52R[5:0]: Peripheral Output Function is Assigned to RP52 Output Pin bits (see Table 3-34 for peripheral function numbers) REGISTER 3-80: RPOR11: PERIPHERAL PIN SELECT OUTPUT REGISTER 11 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP55R5 RP55R4 RP55R3 RP55R2 RP55R1 RP55R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP54R5 RP54R4 RP54R3 RP54R2 RP54R1 RP54R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP55R[5:0]: Peripheral Output Function is Assigned to RP55 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP54R[5:0]: Peripheral Output Function is Assigned to RP54 Output Pin bits (see Table 3-34 for peripheral function numbers)  2017-2019 Microchip Technology Inc. DS70005319D-page 161 dsPIC33CH128MP508 FAMILY REGISTER 3-81: RPOR12: PERIPHERAL PIN SELECT OUTPUT REGISTER 12 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP57R5 RP57R4 RP57R3 RP57R2 RP57R1 RP57R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP56R5 RP56R4 RP56R3 RP56R2 RP56R1 RP56R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP57R[5:0]: Peripheral Output Function is Assigned to RP57 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP56R[5:0]: Peripheral Output Function is Assigned to RP56 Output Pin bits (see Table 3-34 for peripheral function numbers) REGISTER 3-82: RPOR13: PERIPHERAL PIN SELECT OUTPUT REGISTER 13 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP59R5 RP59R4 RP59R3 RP59R2 RP59R1 RP59R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP58R5 RP58R4 RP58R3 RP58R2 RP58R1 RP58R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP59R[5:0]: Peripheral Output Function is Assigned to RP59 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP58R[5:0]: Peripheral Output Function is Assigned to RP58 Output Pin bits (see Table 3-34 for peripheral function numbers) DS70005319D-page 162  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-83: RPOR14: PERIPHERAL PIN SELECT OUTPUT REGISTER 14 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP61R5 RP61R4 RP61R3 RP61R2 RP61R1 RP61R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP60R5 RP60R4 RP60R3 RP60R2 RP60R1 RP60R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP61R[5:0]: Peripheral Output Function is Assigned to RP61 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP60R[5:0]: Peripheral Output Function is Assigned to RP60 Output Pin bits (see Table 3-34 for peripheral function numbers) REGISTER 3-84: RPOR15: PERIPHERAL PIN SELECT OUTPUT REGISTER 15 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP63R5 RP63R4 RP63R3 RP63R2 RP63R1 RP63R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP62R5 RP62R4 RP62R3 RP62R2 RP62R1 RP62R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP63R[5:0]: Peripheral Output Function is Assigned to RP63 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP62R[5:0]: Peripheral Output Function is Assigned to RP62 Output Pin bits (see Table 3-34 for peripheral function numbers)  2017-2019 Microchip Technology Inc. DS70005319D-page 163 dsPIC33CH128MP508 FAMILY REGISTER 3-85: RPOR16: PERIPHERAL PIN SELECT OUTPUT REGISTER 16 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP65R5 RP65R4 RP65R3 RP65R2 RP65R1 RP65R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP64R5 RP64R4 RP64R3 RP64R2 RP64R1 RP64R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP65R[5:0]: Peripheral Output Function is Assigned to RP65 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP64R[5:0]: Peripheral Output Function is Assigned to RP64 Output Pin bits (see Table 3-34 for peripheral function numbers) REGISTER 3-86: RPOR17: PERIPHERAL PIN SELECT OUTPUT REGISTER 17 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP67R5 RP67R4 RP67R3 RP67R2 RP67R1 RP67R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP66R5 RP66R4 RP66R3 RP66R2 RP66R1 RP66R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP67R[5:0]: Peripheral Output Function is Assigned to RP67 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP66R[5:0]: Peripheral Output Function is Assigned to RP66 Output Pin bits (see Table 3-34 for peripheral function numbers) DS70005319D-page 164  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-87: RPOR18: PERIPHERAL PIN SELECT OUTPUT REGISTER 18 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP69R5 RP69R4 RP69R3 RP69R2 RP69R1 RP69R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP68R5 RP68R4 RP68R3 RP68R2 RP68R1 RP68R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP69R[5:0]: Peripheral Output Function is Assigned to RP69 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP68R[5:0]: Peripheral Output Function is Assigned to RP68 Output Pin bits (see Table 3-34 for peripheral function numbers) REGISTER 3-88: RPOR19: PERIPHERAL PIN SELECT OUTPUT REGISTER 19 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP71R5 RP71R4 RP71R3 RP71R2 RP71R1 RP71R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP70R5 RP70R4 RP70R3 RP70R2 RP70R1 RP70R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP71R[5:0]: Peripheral Output Function is Assigned to RP71 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP70R[5:0]: Peripheral Output Function is Assigned to RP70 Output Pin bits (see Table 3-34 for peripheral function numbers)  2017-2019 Microchip Technology Inc. DS70005319D-page 165 dsPIC33CH128MP508 FAMILY REGISTER 3-89: RPOR20: PERIPHERAL PIN SELECT OUTPUT REGISTER 20 U-0 U-0 R/W-0 — — RP177R5(1) R/W-0 R/W-0 RP177R4(1) RP177R3(1) R/W-0 R/W-0 R/W-0 RP177R2(1) RP177R1(1) RP177R0(1) bit 15 bit 8 U-0 U-0 R/W-0 — — RP176R5(1) R/W-0 R/W-0 RP176R4(1) RP176R3(1) R/W-0 R/W-0 R/W-0 RP176R2(1) RP176R1(1) RP176R0(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP177R[5:0]: Peripheral Output Function is Assigned to RP177 Output Pin bits(1) (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP176R[5:0]: Peripheral Output Function is Assigned to RP176 Output Pin bits(1) (see Table 3-34 for peripheral function numbers) Note 1: These are virtual output ports. REGISTER 3-90: U-0 — RPOR21: PERIPHERAL PIN SELECT OUTPUT REGISTER 21 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — RP179R5(1) RP179R4(1) RP179R3(1) RP179R2(1) RP179R1(1) RP179R0(1) bit 15 bit 8 U-0 — U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — RP178R5(1) RP178R4(1) RP178R3(1) RP178R2(1) RP178R1(1) RP178R0(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP179R[5:0]: Peripheral Output Function is Assigned to RP179 Output Pin bits(1) (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP178R[5:0]: Peripheral Output Function is Assigned to RP178 Output Pin bits(1) (see Table 3-34 for peripheral function numbers) Note 1: These are virtual output ports. DS70005319D-page 166  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-91: RPOR22: PERIPHERAL PIN SELECT OUTPUT REGISTER 22 U-0 U-0 R/W-0 — — RP181R5(1) R/W-0 R/W-0 RP181R4(1) RP181R3(1) R/W-0 R/W-0 R/W-0 RP181R2(1) RP181R1(1) RP181R0(1) bit 15 bit 8 U-0 U-0 R/W-0 — — RP180R5(1) R/W-0 R/W-0 RP180R4(1) RP180R3(1) R/W-0 R/W-0 R/W-0 RP180R2(1) RP180R1(1) RP180R0(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP181R[5:0]: Peripheral Output Function is Assigned to RP181 Output Pin bits (see Table 3-34 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP180R[5:0]: Peripheral Output Function is Assigned to RP180 Output Pin bits (see Table 3-34 for peripheral function numbers) Note 1: These are virtual output ports.  2017-2019 Microchip Technology Inc. DS70005319D-page 167 Register Bit 15 MASTER PPS INPUT CONTROL REGISTERS Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 — RPCON — — — — IOLOCK — — — — — — — — — — RPINR0 INT1R7 INT1R6 INT1R5 INT1R4 INT1R3 INT1R2 INT1R1 INT1R0 — — — — — — — — RPINR1 INT3R7 INT3R6 INT3R5 INT3R4 INT3R3 INT3R2 INT3R1 INT3R0 INT2R7 INT2R6 INT2R5 INT2R4 INT2R3 INT2R2 INT2R1 INT2R0 RPINR2 T1CKR7 T1CKR6 T1CKR5 T1CKR4 T1CKR3 T1CKR2 T1CKR1 T1CKR0 — — — — — — — — RPINR3 ICM1R7 ICM1R6 ICM1R5 ICM1R4 ICM1R3 ICM1R2 ICM1R1 ICM1R0 TCKI1R7 TCKI1R6 TCKI1R5 TCKI1R4 TCKI1R3 TCKI1R2 TCKI1R1 TCKI1R0 RPINR4 ICM2R7 ICM2R6 ICM2R5 ICM2R4 ICM2R3 ICM2R2 ICM2R1 ICM2R0 TCKI2R7 TCKI2R6 TCKI2R5 TCKI2R4 TCKI2R3 TCKI2R2 TCKI2R1 TCKI2R0 RPINR5 ICM3R7 ICM3R6 ICM3R5 ICM3R4 ICM3R3 ICM3R2 ICM3R1 ICM3R0 TCKI3R7 TCKI3R6 TCKI3R5 TCKI3R4 TCKI3R3 TCKI3R2 TCKI3R1 TCKI3R0 RPINR6 ICM4R7 ICM4R6 ICM4R5 ICM4R4 ICM4R3 ICM4R2 ICM4R1 ICM4R0 TCKI4R7 TCKI4R TCKI4R5 TCKI4R4 TCKI4R3 TCKI4R2 TCKI4R1 TCKI4R0 RPINR7 ICM5R7 ICM5R6 ICM5R5 ICM5R4 ICM5R3 ICM5R2 ICM5R1 ICM5R0 TCKI5R7 TCKI5R6 TCKI5R5 TCKI5R4 TCKI5R3 TCKI5R2 TCKI5R1 TCKI5R0 RPINR8 ICM6R7 ICM6R6 ICM6R5 ICM6R4 ICM6R3 ICM6R2 ICM6R1 ICM6R0 TCKI6R7 TCKI6R6 TCKI6R5 TCKI6R4 TCKI6R3 TCKI6R2 TCKI6R1 TCKI6R0 RPINR9 ICM7R7 ICM7R6 ICM7R5 ICM7R4 ICM7R3 ICM7R2 ICM7R1 ICM7R0 TCKI7R7 TCKI7R6 TCKI7R5 TCKI7R4 TCKI7R3 TCKI7R2 TCKI7R1 TCKI7R0 RPINR10 ICM8R7 ICM8R6 ICM8R5 ICM8R4 ICM8R3 ICM8R2 ICM8R1 ICM8R0 TCKI8R7 TCKI8R6 TCKI8R5 TCKI8R4 TCKI8R3 TCKI8R2 TCKI8R1 TCKI8R0 RPINR11 OCFBR7 OCFBR6 OCFBR5 OCFBR4 OCFBR3 OCFBR2 OCFBR1 OCFBR0 OCFAR7 OCFAR6 OCFAR5 OCFAR4 OCFAR3 OCFAR2 OCFAR1 OCFAR0 RPINR12 PCI9R7 PCI9R6 PCI9R5 PCI9R4 PCI9R3 PCI9R2 PCI9R1 PCI9R0 PCI8R7 PCI8R6 PCI8R5 PCI8R4 PCI8R3 PCI8R2 PCI8R1 PCI8R0 RPINR13 PCI11R7 PCI11R6 PCI11R5 PCI11R4 PCI11R3 PCI11R2 PCI11R1 PCI11R0 PCI10R7 PCI10R6 PCI10R5 PCI10R4 PCI10R3 PCI10R2 PCI10R1 PCI10R0 RPINR14 QEIB1R7 QEIB1R6 QEIB1R5 QEIB1R4 QEIB1R3 QEIB1R2 QEIB1R1 QEIB1R0 QEIA1R7 QEIA1R6 QEIA1R5 QEIA1R4 QEIA1R3 QEIA1R2 QEIA1R1 QEIA1R0 RPINR15 QEIHOM1R7 QEIHOM1R6 QEIHOM1R5 QEIHOM1R4 QEIHOM1R3 QEIHOM1R2 QEIHOM1R1 QEIHOM1R0 QEINDX1R7 QEINDX1R6 QEINDX1R5 QEINDX1R4 QEINDX1R3 QEINDX1R2 QEINDX1R1 QEINDX1R0  2017-2019 Microchip Technology Inc. RPINR18 U1DSRR7 U1DSRR6 U1DSRR5 U1DSRR4 U1DSRR3 U1DSRR2 U1DSRR1 U1DSRR0 U1RXR7 U1RXR6 U1RXR5 U1RXR4 U1RXR3 U1RXR2 U1RXR1 U1RXR0 RPINR19 U2DSRR7 U2DSRR6 U2DSRR5 U2DSRR4 U2DSRR3 U2DSRR2 U2DSRR1 U2DSRR0 U2RXR7 U2RXR6 U2RXR5 U2RXR4 U2RXR3 U2RXR2 U2RXR1 U2RXR0 RPINR20 SCK1R7 SCK1R6 SCK1R5 SCK1R4 SCK1R3 SCK1R2 SCK1R1 SCK1R0 SDI1R7 SDI1R6 SDI1R5 SDI1R4 SDI1R3 SDI1R2 SDI1R1 SDI1R0 RPINR21 REFOIR7 REFOIR6 REFOIR5 REFOIR4 REFOIR3 REFOIR2 REFOIR1 REFOIR0 SS1R7 SS1R6 SS1R5 SS1R4 SS1R3 SS1R2 SS1R1 SS1R0 RPINR22 SCK2R7 SCK2R6 SCK2R5 SCK2R4 SCK2R3 SCK2R2 SCK2R1 SCK2R0 SDI2R7 SDI2R6 SDI2R5 SDI2R4 SDI2R3 SDI2R2 SDI2R1 SDI2R0 RPINR23 U1CTSR7 U1CTSR6 U1CTSR5 U1CTSR4 U1CTSR3 U1CTSR2 U1CTSR1 U1CTSR0 SS2R7 SS2R6 SS2R5 SS2R4 SS2R3 SS2R2 SS2R1 SS2R0 RPINR26 — — — — — — — — CAN1RXR7 CAN1RXR6 CAN1RXR5 CAN1RXR4 CAN1RXR3 CAN1RXR2 CAN1RXR1 CAN1RXR0 RPINR30 U2CTSR7 U2CTSR6 U2CTSR5 U2CTSR4 U2CTSR3 U2CTSR2 U2CTSR1 U2CTSR0 — — — — — — — — RPINR37 PCI17R7 PCI17R6 PCI17R5 PCI17R4 PCI17R3 PCI17R2 PCI17R1 PCI17R0 — — — — — — — — RPINR38 — — — — — — — — PCI18R7 PCI18R6 PCI18R5 PCI18R4 PCI18R3 PCI18R2 PCI18R1 PCI18R0 RPINR42 PCI13R7 PCI13R6 PCI13R5 PCI13R4 PCI13R3 PCI13R2 PCI13R1 PCI13R0 PCI12R7 PCI12R6 PCI12R5 PCI12R4 PCI12R3 PCI12R2 PCI12R1 PCI12R0 RPINR43 PCI15R7 PCI15R6 PCI15R5 PCI15R4 PCI15R3 PCI15R2 PCI15R1 PCI15R0 PCI14R7 PCI14R6 PCI14R5 PCI14R4 PCI14R3 PCI14R2 PCI14R1 PCI14R0 RPINR44 SENT1R7 SENT1R6 SENT1R5 SENT1R4 SENT1R3 SENT1R2 SENT1R1 SENT1R0 PCI16R7 PCI16R6 PCI16R5 PCI16R4 PCI16R3 PCI16R2 PCI16R1 PCI16R0 RPINR45 CLCINAR7 CLCINAR6 CLCINAR5 CLCINAR4 CLCINAR3 CLCINAR2 CLCINAR1 CLCINAR0 SENT2R7 SENT2R6 SENT2R5 SENT2R4 SENT2R3 SENT2R2 SENT2R1 SENT2R0 RPINR46 CLCINCR7 CLCINCR6 CLCINCR5 CLCINCR4 CLCINCR3 CLCINCR2 CLCINCR1 CLCINCR0 CLCINBR7 CLCINBR6 CLCINBR5 CLCINBR4 CLCINBR3 CLCINBR2 CLCINBR1 CLCINBR0 RPINR47 ADCTRGR7 ADCTRGR6 ADCTRGR5 ADCTRGR4 ADCTRGR3 ADCTRGR2 ADCTRGR1 ADCTRGR0 CLCINDR7 CLCINDR6 CLCINDR5 CLCINDR4 CLCINDR3 CLCINDR2 CLCINDR1 CLCINDR0 dsPIC33CH128MP508 FAMILY DS70005319D-page 168 TABLE 3-40:  2017-2019 Microchip Technology Inc. MASTER PPS OUTPUT CONTROL REGISTERS(1) TABLE 3-41: Register Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 — — RP33R5 RP33R4 RP33R3 RP33R2 RP33R1 RP33R0 — — RP32R5 RP32R4 RP32R3 RP32R2 RP32R1 RP32R0 — — RP35R5 RP35R4 RP35R3 RP35R2 RP35R1 RP35R0 — — RP34R5 RP34R4 RP34R3 RP34R2 RP34R1 RP34R0 RPOR2 — — RP37R5 RP37R4 RP37R3 RP37R2 RP37R1 RP37R0 — — RP36R5 RP36R4 RP36R3 RP36R2 RP36R1 RP36R0 RPOR3 — — RP39R5 RP39R4 RP39R3 RP39R2 RP39R1 RP39R0 — — RP38R5 RP38R4 RP38R3 RP38R2 RP38R1 RP38R0 RPOR4 — — RP41R5 RP41R4 RP41R3 RP41R2 RP41R1 RP41R0 — — RP40R5 RP40R4 RP40R3 RP40R2 RP40R1 RP40R0 RPOR5 — — RP43R5 RP43R4 RP43R3 RP43R2 RP43R1 RP43R0 — — RP42R5 RP42R4 RP42R3 RP42R2 RP42R1 RP42R0 RPOR6 — — RP45R5 RP45R4 RP45R3 RP45R2 RP45R1 RP45R0 — — RP44R5 RP44R4 RP44R3 RP44R2 RP44R1 RP44R0 RPOR7 — — RP47R5 RP47R4 RP47R3 RP47R2 RP47R1 RP47R0 — — RP46R5 RP46R4 RP46R3 RP46R2 RP46R1 RP46R0 RPOR8 — — RP49R5 RP49R4 RP49R3 RP49R2 RP49R1 RP49R0 — — RP48R5 RP48R4 RP48R3 RP48R2 RP48R1 RP48R0 RPOR9 — — RP51R5 RP51R4 RP51R3 RP51R2 RP51R1 RP51R0 — — RP50R5 RP50R4 RP50R3 RP50R2 RP50R1 RP50R0 RPOR10 — — RP53R5 RP53R4 RP53R3 RP53R2 RP53R1 RP53R0 — — RP52R5 RP52R4 RP52R3 RP52R2 RP52R1 RP52R0 RPOR11 — — RP55R5 RP55R4 RP55R3 RP55R2 RP55R1 RP55R0 — — RP54R5 RP54R4 RP54R3 RP54R2 RP54R1 RP54R0 RPOR12 — — RP57R5 RP57R4 RP57R3 RP57R2 RP57R1 RP57R0 — — RP56R5 RP56R4 RP56R3 RP56R2 RP56R1 RP56R0 RPOR13 — — RP59R5 RP59R4 RP59R3 RP59R2 RP59R1 RP59R0 — — RP58R5 RP58R4 RP58R3 RP58R2 RP58R1 RP58R0 RPOR14 — — RP61R5 RP61R4 RP61R3 RP61R2 RP61R1 RP61R0 — — RP60R5 RP60R4 RP60R3 RP60R2 RP60R1 RP60R0 RPOR15 — — RP63R5 RP63R4 RP63R3 RP63R2 RP63R1 RP63R0 — — RP62R5 RP62R4 RP62R3 RP62R2 RP62R1 RP62R0 RPOR16 — — RP65R5 RP65R4 RP65R3 RP65R2 RP65R1 RP65R0 — — RP64R5 RP64R4 RP64R3 RP64R2 RP64R1 RP64R0 RPOR17 — — RP67R5 RP67R4 RP67R3 RP67R2 RP67R1 RP67R0 — — RP66R5 RP66R4 RP66R3 RP66R2 RP66R1 RP66R0 RPOR18 — — RP69R5 RP69R4 RP69R3 RP69R2 RP69R1 RP69R0 — — RP68R5 RP68R4 RP68R3 RP68R2 RP68R1 RP68R0 RPOR19 — — RP71R5 RP71R4 RP71R3 RP71R2 RP71R1 RP71R0 — — RP70R5 RP70R4 RP70R3 RP70R2 RP70R1 RP70R0 RPOR20 — — RP177R5 RP177R4 RP177R3 RP177R2 RP177R1 RP177R0 — — RP176R5 RP176R4 RP176R3 RP176R2 RP176R1 RP176R0 RPOR21 — — RP179R5 RP179R4 RP179R3 RP179R2 RP179R1 RP179R0 — — RP178R5 RP178R4 RP178R3 RP178R2 RP178R1 RP178R0 RPOR22 — — RP181R5 RP181R4 RP181R3 RP181R2 RP181R1 RP181R0 — — RP180R5 RP180R4 RP180R3 RP180R2 RP180R1 RP180R0 Note 1: Not all RP pins are available on all packages. Make sure the selected device variant has the feature available on the device. DS70005319D-page 169 dsPIC33CH128MP508 FAMILY RPOR0 RPOR1 dsPIC33CH128MP508 FAMILY 3.7 Deadman Timer (DMT) (Master Only) Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “Deadman Timer (DMT)” (www.microchip.com/DS70005155) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). DMT can be enabled in the Configuration fuse or by software in the DMTCON register by setting the ON bit. The DMT consists of a 32-bit counter with a time-out count match value, as specified by the two 16-bit Configuration Fuse registers: FDMTCNTL and FDMTCNTH. A DMT is typically used in mission-critical and safetycritical applications, where any single failure of the software functionality and sequencing must be detected. Table 3-42 shows an overview of the DMT module. TABLE 3-42: 2: The Slave core does not have any DMT module; only the Master has the DMT. The primary function of the Deadman Timer (DMT) is to interrupt the processor in the event of a software malfunction. The DMT, which works on the system clock, is a free-running instruction fetch timer, which is clocked whenever an instruction fetch occurs, until a count match occurs. Instructions are not fetched when the processor is in Sleep mode. FIGURE 3-22: DMT MODULE OVERVIEW No. of DMT Modules Identical (Modules) Master Core 1 No Slave Core None NA Figure 3-22 shows a block diagram of the Deadman Timer module. DEADMAN TIMER BLOCK DIAGRAM BAD1 BAD2 Improper Sequence Flag DMT Enable (2) Instruction Fetched Strobe 32-Bit Counter (Counter) = DMT Max Count(1) DMT Event System Clock Note 1: DMT Max Count is controlled by the initial value of the FDMTCNTL and FDMTCNTH Configuration registers. 2: DMT window interval is controlled by the value of the FDMTIVTL and FDMTIVTH Configuration registers. DS70005319D-page 170  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.7.1 DEADMAN TIMER CONTROL/STATUS REGISTERS REGISTER 3-92: DMTCON: DEADMAN TIMER CONTROL REGISTER R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 ON(1) — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 ON: DMT Module Enable bit(1) 1 = Deadman Timer module is enabled 0 = Deadman Timer module is not enabled bit 14-0 Unimplemented: Read as ‘0’ Note 1: x = Bit is unknown This bit has control only when DMTDIS = 0 in the FDMT register. REGISTER 3-93: R/W-0 DMTPRECLR: DEADMAN TIMER PRECLEAR REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 STEP1[7:0] bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 STEP1[7:0]: DMT Preclear Enable bits 01000000 = Enables the Deadman Timer preclear (Step 1) All Other Write Patterns = Sets the BAD1 flag; these bits are cleared when a DMT Reset event occurs. STEP1[7:0] bits are also cleared if the STEP2[7:0] bits are loaded with the correct value in the correct sequence. bit 7-0 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. DS70005319D-page 171 dsPIC33CH128MP508 FAMILY REGISTER 3-94: DMTCLR: DEADMAN TIMER CLEAR REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 STEP2[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7-0 STEP2[7:0]: DMT Clear Timer bits 00001000 = Clears STEP1[7:0], STEP2[7:0] and the Deadman Timer if preceded by the correct loading of the STEP1[7:0] bits in the correct sequence. The write to these bits may be verified by reading the DMTCNTL/H register and observing the counter being reset. All Other Write Patterns = Sets the BAD2 bit; the value of STEP1[7:0] will remain unchanged and the new value being written to STEP2[7:0] will be captured. These bits are cleared when a DMT Reset event occurs. DS70005319D-page 172  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-95: DMTSTAT: DEADMAN TIMER STATUS REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 HC/R-0 HC/R-0 HC/R-0 U-0 U-0 U-0 U-0 R-0 BAD1 BAD2 DMTEVENT — — — — WINOPN bit 7 bit 0 Legend: HC = Hardware Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7 BAD1: Deadman Timer Bad STEP1[7:0] Value Detect bit 1 = Incorrect STEP1[7:0] value was detected 0 = Incorrect STEP1[7:0] value was not detected bit 6 BAD2: Deadman Timer Bad STEP2[7:0] Value Detect bit 1 = Incorrect STEP2[7:0] value was detected 0 = Incorrect STEP2[7:0] value was not detected bit 5 DMTEVENT: Deadman Timer Event bit 1 = Deadman Timer event was detected (counter expired, or bad STEP1[7:0] or STEP2[7:0] value was entered prior to counter increment) 0 = Deadman Timer event was not detected bit 4-1 Unimplemented: Read as ‘0’ bit 0 WINOPN: Deadman Timer Clear Window bit 1 = Deadman Timer clear window is open 0 = Deadman Timer clear window is not open  2017-2019 Microchip Technology Inc. DS70005319D-page 173 dsPIC33CH128MP508 FAMILY REGISTER 3-96: R/W-0 DMTCNTL: DEADMAN TIMER COUNT REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 COUNTER[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 COUNTER[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown COUNTER[15:0]: Read Current Contents of Lower DMT Counter bits REGISTER 3-97: R/W-0 DMTCNTH: DEADMAN TIMER COUNT REGISTER HIGH R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 COUNTER[31:24] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 COUNTER[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown COUNTER[31:16]: Read Current Contents of Higher DMT Counter bits DS70005319D-page 174  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-98: R/W-0 DMTPSCNTL: DMT POST-CONFIGURE COUNT STATUS REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PSCNT[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PSCNT[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown PSCNT[15:0]: Lower DMT Instruction Count Value Configuration Status bits This is always the value of the FDMTCNTL Configuration register. REGISTER 3-99: R/W-0 DMTPSCNTH: DMT POST-CONFIGURE COUNT STATUS REGISTER HIGH R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PSCNT[31:24] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PSCNT[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown PSCNT[31:16]: Higher DMT Instruction Count Value Configuration Status bits This is always the value of the FDMTCNTH Configuration register.  2017-2019 Microchip Technology Inc. DS70005319D-page 175 dsPIC33CH128MP508 FAMILY REGISTER 3-100: DMTPSINTVL: DMT POST-CONFIGURE INTERVAL STATUS REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PSINTV[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PSINTV[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown PSINTV[15:0]: Lower DMT Window Interval Configuration Status bits This is always the value of the FDMTIVTL Configuration register. REGISTER 3-101: DMTPSINTVH: DMT POST-CONFIGURE INTERVAL STATUS REGISTER HIGH R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PSINTV[31:24] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PSINTV[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown PSINTV[31:16]: Higher DMT Window Interval Configuration Status bits This is always the value of the FDMTIVTH Configuration register. DS70005319D-page 176  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-102: DMTHOLDREG: DMT HOLD REGISTER(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 UPRCNT[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 UPRCNT[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-0 UPRCNT[15:0]: DMTCNTH Register Value when DMTCNTL and DMTCNTH were Last Read bits Note 1: The DMTHOLDREG register is initialized to ‘0’ on Reset, and is only loaded when the DMTCNTL and DMTCNTH registers are read.  2017-2019 Microchip Technology Inc. DS70005319D-page 177 dsPIC33CH128MP508 FAMILY 3.8 Controller Area Network (CAN FD) Module (Master Only) Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “CAN Flexible Data-Rate (FD) Protocol Module” (www.microchip.com/ DS70005340) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). 2: Only the Master core has a CAN FD module. Table 3-43 shows an overview of the CAN FD module. TABLE 3-43: CAN FD MODULE OVERVIEW Number of CAN Modules Identical (Modules) Master Core 1 NA Slave Core None NA 3.8.1 FEATURES The CAN FD module has the following features: General • Nominal (Arbitration) Bit Rate up to 1 Mbps • Data Bit Rate up to 8 Mbps • CAN FD Controller modes: - Mixed CAN 2.0B and CAN FD mode - CAN 2.0B mode • Conforms to ISO11898-1:2015 Message FIFOs • Seven FIFOs, Configurable as Transmit or Receive FIFOs • One Transmit Queue (TXQ) • Transmit Event FIFO (TEF) with 32-Bit Timestamp Message Transmission • Message Transmission Prioritization: - Based on priority bit field, and/or - Message with lowest ID gets transmitted first using the TXQ • Programmable Automatic Retransmission Attempts: Unlimited, Three Attempts or Disabled DS70005319D-page 178 Message Reception • 16 Flexible Filter and Mask Objects. • Each Object can be Configured to Filter either: - Standard ID + first 18 data bits or - Extended ID • 32-Bit Timestamp. • The CAN FD Bit Stream Processor (BSP) Implements the Medium Access Control of the CAN FD Protocol Described in ISO11898-1:2015. It serializes and deserializes the bit stream, encodes and decodes the CAN FD frames, manages the medium access, Acknowledges frames, and detects and signals errors. • The TX Handler Prioritizes the Messages that are Requested for Transmission by the Transmit FIFOs. It uses the RAM interface to fetch the transmit data from RAM and provides them to the BSP for transmission. • The BSP provides Received Messages to the RX Handler. The RX handler uses acceptance filters to filter out messages that shall be stored in the Receive FIFOs. It uses the RAM interface to store received data into RAM. • Each FIFO can be Configured either as a Transmit or Receive FIFO. The FIFO control keeps track of the FIFO head and tail, and calculates the user address. In a TX FIFO, the user address points to the address in RAM where the data for the next transmit message shall be stored. In an RX FIFO, the user address points to the address in RAM where the data of the next receive message shall be read. The user notifies the FIFO that a message was written to or read from RAM by incrementing the head/tail of the FIFO. • The Transmit Queue (TXQ) is a Special Transmit FIFO that Transmits the Messages based on the ID of the Messages Stored in the Queue. • The Transmit Event FIFO (TEF) Stores the Message IDs of the Transmitted Messages. • A Free-Running Time Base Counter is used to Timestamp Received Messages. Messages in the TEF can also be timestamped. • The CAN FD Controller module Generates Interrupts when New Messages are Received or when Messages were Transmitted Successfully. Figure 3-23 shows the CAN FD system block diagram. Note: CAN is available only on dsPIC33CHXXXMP50X devices. the  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 3-23: CAN FD MODULE BLOCK DIAGRAM C1TX TX Handler Timestamping TX Prioritization Interrupt Control C1RX RX Handler Error Handling Diagnostics Filter and Masks Device RAM TEF TXQ FIFO 1 FIFO 7 Message Object 0 Message Object 0 Message Object 0 Message Object 0 • • • • • • • • • • Message Object 31 Message Object 31 Message Object 31 Message Object 31  2017-2019 Microchip Technology Inc. • • • • • DS70005319D-page 179 dsPIC33CH128MP508 FAMILY 3.8.2 CAN CONTROL/STATUS REGISTERS REGISTER 3-103: C1CONH: CAN CONTROL REGISTER HIGH(2) R/W-0 R/W-0 R/W-0 R/W-0 S/HC-0 R/W-1 R/W-0 R/W-0 TXBWS3 TXBWS2 TXBWS1 TXBWS0 ABAT REQOP2 REQOP1 REQOP0 bit 15 bit 8 R-1 R-0 R-0 R/W-1 R/W-1 R/W-0 R/W-0 R/W-0 OPMOD2 OPMOD1 OPMOD0 TXQEN(1) STEF(1) SERRLOM(1) ESIGM(1) RTXAT(1) bit 7 bit 0 Legend: S = Settable bit HC = Hardware Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-12 TXBWS[3:0]: Transmit Bandwidth Sharing bits 1111-1100 = 4096 1011 = 2048 1010 = 1024 1001 = 512 1000 = 256 0111 = 128 0110 = 64 0101 = 32 0100 = 16 0011 = 8 0010 = 4 0001 = 2 0000 = No delay bit 11 ABAT: Abort All Pending Transmissions bit 1 = Signals all transmit buffers to abort transmission 0 = Module will clear this bit when all transmissions are aborted bit 10-8 REQOP[2:0]: Request Operation Mode bits 111 = Sets Restricted Operation mode 110 = Sets Normal CAN 2.0 mode; error frames on CAN FD frames 101 = Sets External Loopback mode 100 = Sets Configuration mode 011 = Sets Listen Only mode 010 = Sets Internal Loopback mode 001 = Sets Disable mode 000 = Sets Normal CAN FD mode; supports mixing of full CAN FD and classic CAN 2.0 frames bit 7-5 OPMOD[2:0]: Operation Mode Status bits 111 = Module is in Restricted Operation mode 110 = Module is in Normal CAN 2.0 mode; error frames on CAN FD frames 101 = Module is in External Loopback mode 100 = Module is in Configuration mode 011 = Module is in Listen Only mode 010 = Module is in Internal Loopback mode 001 = Module is in Disable mode 000 = Module is in Normal CAN FD mode; supports mixing of full CAN FD and classic CAN 2.0 frames Note 1: 2: These bits can only be modified in Configuration mode (OPMOD[2:0] = 100). CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 180  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-103: C1CONH: CAN CONTROL REGISTER HIGH(2) (CONTINUED) bit 4 TXQEN: Enable Transmit Queue bit(1) 1 = Enables Transmit Message Queue (TXQ) and reserves space in RAM 0 = Does not reserve space in RAM for TXQ bit 3 STEF: Store in Transmit Event FIFO bit(1) 1 = Saves transmitted messages in TEF 0 = Does not save transmitted messages in TEF bit 2 SERRLOM: Transition to Listen Only Mode on System Error bit(1) 1 = Transitions to Listen Only mode 0 = Transitions to Restricted Operation mode bit 1 ESIGM: Transmit ESI in Gateway Mode bit(1) 1 = ESI is transmitted as recessive when ESI of the message is high or CAN controller is error passive 0 = ESI reflects error status of CAN controller bit 0 RTXAT: Restrict Retransmission Attempts bit(1) 1 = Restricted retransmission attempts, uses TXAT[1:0] bits (C1TXQCONH[6:5]) 0 = Unlimited number of retransmission attempts, TXAT[1:0] bits will be ignored Note 1: 2: These bits can only be modified in Configuration mode (OPMOD[2:0] = 100). CAN is available only on the dsPIC33CHXXXMP50X devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 181 dsPIC33CH128MP508 FAMILY REGISTER 3-104: C1CONL: CAN CONTROL REGISTER LOW(2) R/W-0 CON U-0 — R/W-0 SIDL R/W-0 BRSDIS R/W-0 BUSY R/W-1 WFT1 R/W-1 WFT0 R/W-1 WAKFIL(1) bit 15 bit 8 R/W-0 CLKSEL(1) bit 7 R/W-1 R/W-1 R/W-0 R/W-0 R/W-0 R/W-0 PXEDIS(1) ISOCRCEN(1) DNCNT4 DNCNT3 DNCNT2 DNCNT1 R/W-0 DNCNT0 bit 0 Legend: R = Readable bit -n = Value at POR bit 15 bit 14 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown CON: CAN Enable bit 1 = CAN module is enabled 0 = CAN module is disabled Unimplemented: Read as ‘0’ bit 13 SIDL: CAN Stop in Idle Control bit 1 = Stops module operation in Idle mode 0 = Does not stop module operation in Idle mode bit 12 BRSDIS: Bit Rate Switching (BRS) Disable bit 1 = Bit Rate Switching is disabled, regardless of BRS in the transmit message object 0 = Bit Rate Switching depends on BRS in the transmit message object BUSY: CAN Module is Busy bit 1 = The CAN module is active 0 = The CAN module is inactive bit 11 bit 10-9 bit 8 WFT[1:0]: Selectable Wake-up Filter Time bits 11 = T11FILTER 10 = T10FILTER 01 = T01FILTER 00 = T00FILTER WAKFIL: Enable CAN Bus Line Wake-up Filter bit(1) 1 = Uses CAN bus line filter for wake-up 0 = CAN bus line filter is not used for wake-up bit 7 CLKSEL: Module Clock Source Select bit(1) 1 = AFPLLO is selected as the source 0 = FCAN is selected as the source bit 6 PXEDIS: Protocol Exception Event Detection Disabled bit(1) A recessive “reserved bit” following a recessive FDF bit is called a Protocol Exception. 1 = Protocol Exception is treated as a form error 0 = If a Protocol Exception is detected, CAN will enter the bus integrating state bit 5 ISOCRCEN: Enable ISO CRC in CAN FD Frames bit(1) 1 = Includes stuff bit count in CRC field and uses non-zero CRC initialization vector 0 = Does not include stuff bit count in CRC field and uses CRC initialization vector with all zeros DNCNT[4:0]: DeviceNet™ Filter Bit Number bits 10011-11111 = Invalid selection (compares up to 18 bits of data with EID) 10010 = Compares up to Data Byte 2, bit 6 with EID17 ... 00001 = Compares up to Data Byte 0, bit 7 with EID0 00000 = Does not compare data bytes bit 4-0 Note 1: 2: These bits can only be modified in Configuration mode (OPMOD[2:0] = 100). CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 182  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-105: C1NBTCFGH: CAN NOMINAL BIT TIME CONFIGURATION REGISTER HIGH(1,2) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 BRP[7:0] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-0 R/W-0 TSEG1[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 BRP[7:0]: Baud Rate Prescaler bits 1111 1111 = TQ = 256/FSYS ... 0000 0000 = TQ = 1/FSYS bit 7-0 TSEG1[7:0]: Time Segment 1 bits (Propagation Segment + Phase Segment 1) 1111 1111 = Length is 256 x TQ ... 0000 0000 = Length is 1 x TQ Note 1: 2: These bits can only be modified in Configuration mode (OPMOD[2:0] = 100). CAN is available only on the dsPIC33CHXXXMP50X devices. REGISTER 3-106: C1NBTCFGL: CAN NOMINAL BIT TIME CONFIGURATION REGISTER LOW(1,2) U-0 — R/W-0 R/W-0 R/W-0 R/W-1 TSEG2[6:0] R/W-1 R/W-1 R/W-1 bit 15 bit 8 U-0 R/W-0 R/W-0 R/W-0 — R/W-1 R/W-1 R/W-1 R/W-1 SJW[6:0] bit 7 bit 0 Legend: R = Readable bit -n = Value at POR W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown bit 15 bit 14-8 Unimplemented: Read as ‘0’ TSEG2[6:0]: Time Segment 2 bits (Phase Segment 2) 111 1111 = Length is 128 x TQ ... 000 0000 = Length is 1 x TQ bit 7 bit 6-0 Unimplemented: Read as ‘0’ SJW[6:0]: Synchronization Jump Width bits 111 1111 = Length is 128 x TQ ... 000 0000 = Length is 1 x TQ Note 1: 2: These bits can only be modified in Configuration mode (OPMOD[2:0] = 100). CAN is available only on the dsPIC33CHXXXMP50X devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 183 dsPIC33CH128MP508 FAMILY REGISTER 3-107: C1DBTCFGH: CAN DATA BIT TIME CONFIGURATION REGISTER HIGH(1,2) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 BRP[7:0] R/W-0 R/W-0 R/W-0 bit 15 bit 8 U-0 U-0 U-0 — — — R/W-0 R/W-1 R/W-1 R/W-1 R/W-0 TSEG1[4:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 BRP[7:0]: Baud Rate Prescaler bits 1111 1111 = TQ = 256/FSYS ... 0000 0000 = TQ = 1/FSYS bit 7-5 bit 4-0 Unimplemented: Read as ‘0’ TSEG1[4:0]: Time Segment 1 bits (Propagation Segment + Phase Segment 1) 1 1111 = Length is 32 x TQ ... 0 0000 = Length is 1 x TQ Note 1: 2: This register can only be modified in Configuration mode (OPMOD[2:0] = 100). CAN is available only on the dsPIC33CHXXXMP50X devices. REGISTER 3-108: C1DBTCFGL: CAN DATA BIT TIME CONFIGURATION REGISTER LOW(1,2) U-0 — U-0 — U-0 — U-0 — R/W-0 R/W-0 R/W-1 TSEG2[3:0] R/W-1 bit 15 bit 8 U-0 U-0 U-0 U-0 — — — — R/W-0 R/W-0 R/W-1 R/W-1 SJW[3:0] bit 7 bit 0 Legend: R = Readable bit -n = Value at POR W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown bit 15-12 bit 11-8 Unimplemented: Read as ‘0’ TSEG2[3:0]: Time Segment 2 bits (Phase Segment 2) 1111 = Length is 16 x TQ ... 0000 = Length is 1 x TQ bit 7-4 Unimplemented: Read as ‘0’ bit 3-0 SJW[3:0]: Synchronization Jump Width bits 1111 = Length is 16 x TQ ... 0000 = Length is 1 x TQ Note 1: 2: This register can only be modified in Configuration mode (OPMOD[2:0] = 100). CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 184  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-109: C1TDCH: CAN TRANSMITTER DELAY COMPENSATION REGISTER HIGH(1,2) U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 — — — — — — EDGFLTEN SID11EN bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 R/W-1 R/W-0 — — — — — — TDCMOD1 TDCMOD0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-10 Unimplemented: Read as ‘0’ bit 9 EDGFLTEN: Enable Edge Filtering During Bus Integration State bit 1 = Edge filtering is enabled according to ISO11898-1:2015 0 = Edge filtering is disabled bit 8 SID11EN: Enable 12-Bit SID in CAN FD Base Format Messages bit 1 = RRS is used as SID11 in CAN FD base format messages: SID[11:0] = {SID[10:0], SID11} 0 = Does not use RRS; SID[10:0] bit 7-2 Unimplemented: Read as ‘0’ bit 1-0 TDCMOD[1:0]: Transmitter Delay Compensation Mode bits (Secondary Sample Point (SSP)) 10-11 = Auto: Measures delay and adds TSEG1[4:0] (C1DBTCFGH[4:0]), adds TDCO[6:0] 01 = Manual: Does not measure, uses TDCV[5:0] + TDCO[6:0] from register 00 = Disable Note 1: 2: This register can only be modified in Configuration mode (OPMOD[2:0] = 100). CAN is available only on the dsPIC33CHXXXMP50X devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 185 dsPIC33CH128MP508 FAMILY REGISTER 3-110: C1TDCL: CAN TRANSMITTER DELAY COMPENSATION REGISTER LOW(1,2) U-0 R/W-0 R/W-0 R/W-1 — R/W-0 R/W-0 R/W-0 R/W-0 TDCO[6:0] bit 15 bit 8 U-0 U-0 — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TDCV[5:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-8 TDCO[6:0]: Transmitter Delay Compensation Offset bits (Secondary Sample Point (SSP)) 111 1111 = -64 x TSYS ... 011 1111 = 63 x TSYS ... 000 0000 = 0 x TSYS bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 TDCV[5:0]: Transmitter Delay Compensation Value bits (Secondary Sample Point (SSP)) 11 1111 = FP ... 00 0000 = 0 x FP Note 1: 2: This register can only be modified in Configuration mode (OPMOD[2:0] = 100). CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 186  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-111: C1TBCH: CAN TIME BASE COUNTER REGISTER HIGH(1,2,3) , R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TBC[31:24] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TBC[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-0 TBC[31:16]: CAN Time Base Counter bits This is a free-running timer that increments every TBCPREx clock when TBCEN is set. Note 1: 2: 3: The Time Base Counter (TBC) will be stopped and reset when TBCEN = 0 to save power. The TBC prescaler count will be reset on any write to C1TBCH/L (TBCPREx will be unaffected). CAN is available only on the dsPIC33CHXXXMP50X devices. REGISTER 3-112: C1TBCL: CAN TIME BASE COUNTER REGISTER LOW(1,2,3) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TBC[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TBC[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-0 TBC[15:0]: CAN Time Base Counter bits This is a free-running timer that increments every TBCPREx clock when TBCEN is set. Note 1: 2: 3: The TBC will be stopped and reset when TBCEN = 0 to save power. The TBC prescaler count will be reset on any write to C1TBCH/L (TBCPREx will be unaffected). CAN is available only on the dsPIC33CHXXXMP50X devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 187 dsPIC33CH128MP508 FAMILY REGISTER 3-113: C1TSCONH: CAN TIMESTAMP CONTROL REGISTER HIGH(1) U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 15 bit 8 U-0 — U-0 — U-0 — U-0 — U-0 — R/W-0 TSRES R/W-0 TSEOF R/W-0 TBCEN bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-3 bit 2 Unimplemented: Read as ‘0’ TSRES: Timestamp Reset bit (CAN FD frames only) 1 = At sample point of the bit following the FDF bit 0 = At sample point of Start-of-Frame (SOF) bit 1 TSEOF: Timestamp End-of-Frame (EOF) bit 1 = Timestamp when frame is taken valid (11898-1 10.7): - RX no error until last, but one bit of EOF - TX no error until the end of EOF 0 = Timestamp at “beginning” of frame: - Classical Frame: At sample point of SOF - FD Frame: See TSRES bit TBCEN: Time Base Counter Enable bit 1 = Enables TBC 0 = Stops and resets TBC bit 0 Note 1: x = Bit is unknown CAN is available only on the dsPIC33CHXXXMP50X devices. REGISTER 3-114: C1TSCONL: CAN TIMESTAMP CONTROL REGISTER LOW(1) U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — R/W-0 R/W-0 TBCPRE[9:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TBCPRE[7:0] bit 7 bit 0 Legend: R = Readable bit -n = Value at POR W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown bit 15-10 Unimplemented: Read as ‘0’ bit 9-0 TBCPRE[9:0]: CAN Time Base Counter Prescaler bits 1023 = TBC increments every 1024 clocks ... 0 = TBC increments every 1 clock Note 1: CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 188  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-115: C1VECH: CAN INTERRUPT CODE REGISTER HIGH(1) U-0 R-1 R-0 R-0 — R-0 R-0 R-0 R-0 RXCODE[6:0] bit 15 bit 8 U-0 R-1 R-0 — R-0 R-0 R-0 R-0 R-0 TXCODE[6:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 Unimplemented: Read as ‘0’ bit 14-8 RXCODE[6:0]: Receive Interrupt Flag Code bits 1000001-1111111 = Reserved 1000000 = No interrupt 0001000-0111111 = Reserved 0000111 = FIFO 7 interrupt (RFIF7 is set) ... 0000010 = FIFO 2 interrupt (RFIF2 is set) 0000001 = FIFO 1 interrupt (RFIF1 is set) 0000000 = Reserved; FIFO 0 cannot receive bit 7 Unimplemented: Read as ‘0’ bit 6-0 TXCODE[6:0]: Transmit Interrupt Flag Code bits 1000001-1111111 = Reserved 1000000 = No interrupt 0001000-0111111 = Reserved 0000111 = FIFO 7 interrupt (TFIF7 is set) ... 0000001 = FIFO 1 interrupt (TFIF1 is set) 0000000 = FIFO 0 interrupt (TFIF0 is set) Note 1: x = Bit is unknown CAN is available only on the dsPIC33CHXXXMP50X devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 189 dsPIC33CH128MP508 FAMILY REGISTER 3-116: C1VECL: CAN INTERRUPT CODE REGISTER LOW(1) U-0 U-0 U-0 — — — R-0 R-0 R-0 R-0 R-0 FILHIT[4:0] bit 15 bit 8 U-0 R-1 R-0 — R-0 R-0 R-0 R-0 R-0 ICODE[6:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-13 Unimplemented: Read as ‘0’ bit 12-8 FILHIT[4:0]: Filter Hit Number bits 01111 = Filter 15 01110 = Filter 14 ... 00001 = Filter 1 00000 = Filter 0 bit 7 Unimplemented: Read as ‘0’ bit 6-0 ICODE[6:0]: Interrupt Flag Code bits 1001011-1111111 = Reserved 1001010 = Transmit attempt interrupt (any bit in C1TXATIF is set) 1001001 = Transmit event FIFO interrupt (any bit in C1TEFSTA is set) 1001000 = Invalid message occurred (IVMIF/IE) 1000111 = CAN module mode change occurred (MODIF/IE) 1000110 = CAN timer overflow (TBCIF/IE) 1000101 = RX/TX MAB overflow/underflow (RX: Message received before previous message was saved to memory; TX: Can’t feed TX MAB fast enough to transmit consistent data) 1000100 = Address error interrupt (illegal FIFO address presented to system) 1000011 = Receive FIFO overflow interrupt (any bit in C1RXOVIF is set) 1000010 = Wake-up interrupt (WAKIF/WAKIE) 1000001 = Error interrupt (CERRIF/IE) 1000000 = No interrupt 0001000-0111111 = Reserved 0000111 = FIFO 7 interrupt (TFIF7 or RFIF7 is set) ... 0000001 = FIFO 1 interrupt (TFIF1 or RFIF1 is set) 0000000 = FIFO 0 interrupt (TFIF0 is set) Note 1: CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 190  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-117: C1INTH: CAN INTERRUPT REGISTER HIGH(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 IVMIE WAKIE CERRIE SERRIE RXOVIE TXATIE — — bit 15 bit 8 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — TEFIE MODIE TBCIE RXIE TXIE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 IVMIE: Invalid Message Interrupt Enable bit 1 = Invalid message interrupt is enabled 0 = Invalid message interrupt is disabled bit 14 WAKIE: Bus Wake-up Activity Interrupt Enable bit 1 = Wake-up activity interrupt is enabled 0 = Wake-up Activity Interrupt is disabled bit 13 CERRIE: CAN Bus Error Interrupt Enable bit 1 = CAN bus error interrupt is enabled 0 = CAN bus error interrupt is disabled bit 12 SERRIE: System Error Interrupt Enable bit 1 = System error interrupt is enabled 0 = System error interrupt is disabled bit 11 RXOVIE: Receive Buffer Overflow Interrupt Enable bit 1 = Receive buffer overflow interrupt is enabled 0 = Receive buffer overflow interrupt is disabled bit 10 TXATIE: Transmit Attempt Interrupt Enable bit 1 = Transmit attempt interrupt is enabled 0 = Transmit attempt interrupt is disabled bit 9-5 Unimplemented: Read as ‘0’ bit 4 TEFIE: Transmit Event FIFO Interrupt Enable bit 1 = Transmit event FIFO interrupt is enabled 0 = Transmit event FIFO interrupt is disabled bit 3 MODIE: Mode Change Interrupt Enable bit 1 = Mode change interrupt is enabled 0 = Mode change interrupt is disabled bit 2 TBCIE: CAN Timer Interrupt Enable bit 1 = CAN timer interrupt is enabled 0 = CAN timer interrupt is disabled bit 1 RXIE: Receive Object Interrupt Enable bit 1 = Receive object interrupt is enabled 0 = Receive object interrupt is disabled bit 0 TXIE: Transmit Object Interrupt Enable bit 1 = Transmit object interrupt is enabled 0 = Transmit object interrupt is disabled Note 1: x = Bit is unknown CAN is available only on the dsPIC33CHXXXMP50X devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 191 dsPIC33CH128MP508 FAMILY REGISTER 3-118: C1INTL: CAN INTERRUPT REGISTER LOW(2) HS/C-0 IVMIF (1) HS/C-0 HS/C-0 HS/C-0 R-0 R-0 U-0 U-0 WAKIF(1) CERRIF(1) SERRIF(1) RXOVIF TXATIF — — bit 15 bit 8 U-0 U-0 — — U-0 — R-0 HS/C-0 (1) TEFIF MODIF HS/C-0 TBCIF (1) R-0 R-0 RXIF TXIF bit 7 bit 0 Legend: C = Clearable bit HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 IVMIF: Invalid Message Interrupt Flag bit(1) 1 = Invalid message interrupt occurred 0 = No invalid message interrupt bit 14 WAKIF: Bus Wake-up Activity Interrupt Flag bit(1) 1 = Wake-up activity interrupt occurred 0 = No wake-up activity interrupt bit 13 CERRIF: CAN Bus Error Interrupt Flag bit(1) 1 = CAN bus error interrupt occurred 0 = No CAN bus error interrupt bit 12 SERRIF: System Error Interrupt Flag bit(1) 1 = System error interrupt occurred 0 = No system error interrupt bit 11 RXOVIF: Receive Buffer Overflow Interrupt Flag bit 1 = Receive buffer overflow interrupt occurred 0 = No receive buffer overflow interrupt bit 10 TXATIF: Transmit Attempt Interrupt Flag bit 1 = Transmit attempt interrupt occurred 0 = No Transmit Attempt Interrupt bit 9-5 Unimplemented: Read as ‘0’ bit 4 TEFIF: Transmit Event FIFO Interrupt Flag bit 1 = Transmit event FIFO interrupt occurred 0 = No transmit event FIFO interrupt bit 3 MODIF: CAN Mode Change Interrupt Flag bit(1) 1 = CAN module mode change occurred (OPMOD[2:0] have changed to reflect REQOP[2:0]) 0 = No mode change occurred bit 2 TBCIF: CAN Timer Overflow Interrupt Flag bit(1) 1 = TBC has overflowed 0 = TBC has not overflowed bit 1 RXIF: Receive Object Interrupt Flag bit 1 = Receive object interrupt is pending 0 = No receive object interrupts are pending bit 0 TXIF: Transmit Object Interrupt Flag bit 1 = Transmit object interrupt is pending 0 = No transmit object interrupts are pending Note 1: 2: C1INTL: Flags are set by hardware and cleared by application. CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 192  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-119: C1RXIFH: CAN RECEIVE INTERRUPT STATUS REGISTER HIGH(1,2) R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 RFIF[31:24] bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 RFIF[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: 2: x = Bit is unknown RFIF[31:16]: Unimplemented C1RXIFH: FIFO: RFIFx = ‘or’ of enabled RX FIFO flags (flags need to be cleared in the FIFO register). CAN is available only on the dsPIC33CHXXXMP50X devices. REGISTER 3-120: C1RXIFL: CAN RECEIVE INTERRUPT STATUS REGISTER LOW(1,2) R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 RFIF[15:8] bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 U-0 — RFIF[7:1] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-8 RFIF[15:8]: Unimplemented bit 7-1 RFIF[7:1]: Receive FIFO Interrupt Pending bits 1 = One or more enabled receive FIFO interrupts are pending 0 = No enabled receive FIFO interrupts are pending bit 0 Unimplemented: Read as ‘0’ Note 1: 2: x = Bit is unknown C1RXIFL: FIFO: RFIFx = ‘or’ of enabled RX FIFO flags (flags need to be cleared in the FIFO register). CAN is available only on the dsPIC33CHXXXMP50X devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 193 dsPIC33CH128MP508 FAMILY REGISTER 3-121: C1RXOVIFH: CAN RECEIVE OVERFLOW INTERRUPT STATUS REGISTER HIGH(1,2) R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 RFOVIF[31:24] bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 RFOVIF[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: 2: x = Bit is unknown RFOVIF[31:16]: Unimplemented C1RXOVIFH: FIFO: RFOVIFx (flag needs to be cleared in the FIFO register). CAN is available only on the dsPIC33CHXXXMP50X devices. REGISTER 3-122: C1RXOVIFL: CAN RECEIVE OVERFLOW INTERRUPT STATUS REGISTER LOW(1,2) R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 RFOVIF[15:8] bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 U-0 — RFOVIF[7:1] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-8 RFOVIF[15:8]: Unimplemented bit 7-1 RFOVIF[7:1]: Receive FIFO Overflow Interrupt Pending bits 1 = Interrupt is pending 0 = Interrupt is not pending bit 0 Unimplemented: Read as ‘0’ Note 1: 2: x = Bit is unknown C1RXOVIFL: FIFO: RFOVIFx (flag needs to be cleared in the FIFO register). CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 194  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-123: C1TXIFH: CAN TRANSMIT INTERRUPT STATUS REGISTER HIGH(1,2) R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 TFIF[31:24] bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 TFIF[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: 2: x = Bit is unknown TFIF[31:16]: Unimplemented C1TXIFH: FIFO: TFIFx = ‘or’ of the enabled TX FIFO flags (flags need to be cleared in the FIFO register). CAN is available only on the dsPIC33CHXXXMP50X devices. REGISTER 3-124: C1TXIFL: CAN TRANSMIT INTERRUPT STATUS REGISTER LOW(1,3) R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 TFIF[15:8] bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 (2) TFIF[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-8 TFIF[15:8]: Unimplemented bit 7-0 TFIF[7:0]: Transmit FIFO/TXQ Interrupt Pending bits(2) 1 = One or more enabled transmit FIFO/TXQ interrupts are pending 0 = No enabled transmit FIFO/TXQ interrupts are pending Note 1: 2: 3: x = Bit is unknown C1TXIFL: FIFO: TFIFx = ‘or’ of the enabled TX FIFO flags (flags need to be cleared in the FIFO register). TFIF0 is for the transmit queue. CAN is available only on the dsPIC33CHXXXMP50X devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 195 dsPIC33CH128MP508 FAMILY REGISTER 3-125: C1TXATIFH: CAN TRANSMIT ATTEMPT INTERRUPT STATUS REGISTER HIGH(1,2) R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 TFATIF[31:24] bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 TFATIF[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: 2: x = Bit is unknown TFATIF[31:16]: Unimplemented C1TXATIFH: FIFO: TFATIFx (flag needs to be cleared in the FIFO register). CAN is available only on the dsPIC33CHXXXMP50X devices. REGISTER 3-126: C1TXATIFL: CAN TRANSMIT ATTEMPT INTERRUPT STATUS REGISTER LOW(1,3) R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 TFATIF[15:8] bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 TFATIF[7:0](2) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 TFATIF[15:8]: Unimplemented bit 7-0 TFATIF[7:0]: Transmit FIFO/TXQ Attempt Interrupt Pending bits(2) 1 = Interrupt is pending 0 = Interrupt is not pending Note 1: 2: 3: C1TXATIFL: FIFO: TFATIFx (flag needs to be cleared in the FIFO register). TFATIF0 is for the transmit queue. CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 196  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-127: C1TXREQH: CAN TRANSMIT REQUEST REGISTER HIGH(1) S/HC-0 S/HC-0 S/HC-0 S/HC-0 S/HC-0 S/HC-0 S/HC-0 S/HC-0 TXREQ[31:24] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 S/HC-0 TXREQ[23:16] bit 7 bit 0 Legend: S = Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: HC = Hardware Clearable bit x = Bit is unknown TXREQ[31:16]: Unimplemented CAN is available only on the dsPIC33CHXXXMP50X devices. REGISTER 3-128: C1TXREQL: CAN TRANSMIT REQUEST REGISTER LOW(1) S/HC-0 S/HC-0 S/HC-0 S/HC-0 S/HC-0 S/HC-0 S/HC-0 S/HC-0 TXREQ[15:8] bit 15 bit 8 S/HC-0 S/HC-0 S/HC-0 S/HC-0 S/HC-0 S/HC-0 S/HC-0 TXREQ[7:1] S/HC-0s TXREQ0 bit 7 bit 0 Legend: S = Settable bit HC = Hardware Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 TXREQ[15:8]: Unimplemented bit 7-1 TXREQ[7:1]: Message Send Request bits TXEN = 1 (object configured as a transmit object): Setting this bit to ‘1’ requests sending a message. The bit will automatically clear when the message(s) queued in the object is (are) successfully sent. This bit can NOT be used for aborting a transmission. TXEN = 0 (object configured as a receive object): This bit has no effect. bit 0 TXREQ0: Transmit Queue Message Send Request bit Setting this bit to ‘1’ requests sending a message. The bit will automatically clear when the message(s) queued in the object is (are) successfully sent. This bit can NOT be used for aborting a transmission. Note 1: CAN is available only on the dsPIC33CHXXXMP50X devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 197 dsPIC33CH128MP508 FAMILY REGISTER 3-129: C1FIFOBAH: CAN MESSAGE MEMORY BASE ADDRESS REGISTER HIGH(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FIFOBA[31:24] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FIFOBA[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: x = Bit is unknown FIFOBA[31:16]: Message Memory Base Address bits Defines the base address for the transmit event FIFO followed by the message objects. CAN is available only on the dsPIC33CHXXXMP50X devices. REGISTER 3-130: C1FIFOBAL: CAN MESSAGE MEMORY BASE ADDRESS REGISTER LOW(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FIFOBA[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R-0 R-0 FIFOBA[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: x = Bit is unknown FIFOBA[15:0]: Message Memory Base Address bits Defines the base address for the transmit event FIFO followed by the message objects. CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 198  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-131: C1TXQCONH: CAN TRANSMIT QUEUE CONTROL REGISTER HIGH(2) R/W-0 PLSIZE2 R/W-0 (1) PLSIZE1 R/W-0 (1) PLSIZE0 R/W-0 (1) (1) FSIZE4 R/W-0 FSIZE3 (1) R/W-0 FSIZE2 (1) R/W-0 FSIZE1 (1) R/W-0 FSIZE0(1) bit 15 bit 8 U-0 R/W-1 R/W-1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — TXAT1 TXAT0 TXPRI4 TXPRI3 TXPRI2 TXPRI1 TXPRI0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-13 PLSIZE[2:0]: Payload Size bits(1) 111 = 64 data bytes 110 = 48 data bytes 101 = 32 data bytes 100 = 24 data bytes 011 = 20 data bytes 010 = 16 data bytes 001 = 12 data bytes 000 = 8 data bytes bit 12-8 FSIZE[4:0]: FIFO Size bits(1) 11111 = FIFO is 32 messages deep ... 00010 = FIFO is 3 messages deep 00001 = FIFO is 2 messages deep 00000 = FIFO is 1 message deep bit 7 Unimplemented: Read as ‘0’ bit 6-5 TXAT[1:0]: Retransmission Attempts bits This feature is enabled when RTXAT (C1CONH[0]) is set. 11 = Unlimited number of retransmission attempts 10 = Unlimited number of retransmission attempts 01 = Three retransmission attempts 00 = Disables retransmission attempts bit 4-0 TXPRI[4:0]: Message Transmit Priority bits 11111 = Highest message priority ... 00000 = Lowest message priority Note 1: 2: x = Bit is unknown These bits can only be modified in Configuration mode (OPMOD[2:0] = 100). CAN is available only on the dsPIC33CHXXXMP50X devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 199 dsPIC33CH128MP508 FAMILY REGISTER 3-132: C1TXQCONL: CAN TRANSMIT QUEUE CONTROL REGISTER LOW(1) U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 — — — — — FRESET TXREQ UINC bit 15 bit 8 R-0 U-0 U-0 HS/C-0 U-0 R/W-0 U-0 R/W-0 TXEN — — TXATIE — TXQEIE — TXQNIE bit 7 bit 0 Legend: HS = Hardware Settable bit C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-11 Unimplemented: Read as ‘0’ bit 10 FRESET: FIFO Reset bit 1 = FIFO will be reset when bit is set, cleared by hardware when FIFO is reset; user should poll whether this bit is clear before taking any action 0 = No effect bit 9 TXREQ: Message Send Request bit 1 = Requests sending a message; the bit will automatically clear when all the messages queued in the TXQ are successfully sent 0 = Clearing the bit to ‘0’ while set (‘1’) will request a message abort bit 8 UINC: Increment Head/Tail bit When this bit is set, the FIFO head will increment by a single message. bit 7 TXEN: TX Enable bit bit 6-5 Unimplemented: Read as ‘0’ bit 4 TXATIE: Transmit Attempts Exhausted Interrupt Enable bit 1 = Enables interrupt 0 = Disables interrupt bit 3 Unimplemented: Read as ‘0’ bit 2 TXQEIE: Transmit Queue Empty Interrupt Enable bit 1 = Interrupt is enabled for TXQ empty 0 = Interrupt is disabled for TXQ empty bit 1 Unimplemented: Read as ‘0’ bit 0 TXQNIE: Transmit Queue Not Full Interrupt Enable bit 1 = Interrupt is enabled for TXQ not full 0 = Interrupt is disabled for TXQ not full Note 1: CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 200  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-133: C1TXQSTA: CAN TRANSMIT QUEUE STATUS REGISTER(3) U-0 U-0 — U-0 — — R-0 TXQCI4 R-0 (1) R-0 (1) TXQCI3 R-0 (1) TXQCI2 R-0 (1) TXQCI1 TXQCI0(1) bit 15 bit 8 R-0 TXABT (2) R-0 R-0 HS/C-0 U-0 R-1 U-0 R-1 TXLARB TXERR TXATIF — TXQEIF — TXQNIF bit 7 bit 0 Legend: HS = Hardware Settable bit C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-13 Unimplemented: Read as ‘0’ bit 12-8 TXQCI[4:0]: Transmit Message Queue Index bits(1) A read of this register will return an index to the message that the FIFO will next attempt to transmit. bit 7 TXABT: Message Aborted Status bit(2) 1 = Message was aborted 0 = Message completed successfully bit 6 TXLARB: Message Lost Arbitration Status bit 1 = Message lost arbitration while being sent 0 = Message did not lose arbitration while being sent bit 5 TXERR: Error Detected During Transmission bit 1 = A bus error occurred while the message was being sent 0 = A bus error did not occur while the message was being sent bit 4 TXATIF: Transmit Attempts Exhausted Interrupt Pending bit 1 = Interrupt is pending 0 = Interrupt is not pending bit 3 Unimplemented: Read as ‘0’ bit 2 TXQEIF: Transmit Queue Empty Interrupt Flag bit 1 = TXQ is empty 0 = TXQ is not empty, at least one message is queued to be transmitted bit 1 Unimplemented: Read as ‘0’ bit 0 TXQNIF: Transmit Queue Not Full Interrupt Flag bit 1 = TXQ is not full 0 = TXQ is full Note 1: 2: 3: The TXQCI[4:0] bits give a zero-indexed value to the message in the TXQ. If the TXQ is four messages deep (FSIZE[4:0] = 3), TXQCIx will take on a value of 0 to 3, depending on the state of the TXQ. This bit is updated when a message completes (or aborts) or when the TXQ is reset. CAN is available only on the dsPIC33CHXXXMP50X devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 201 dsPIC33CH128MP508 FAMILY REGISTER 3-134: C1FIFOCONxH: CAN FIFO CONTROL REGISTER x (x = 1 TO 7) HIGH(2) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PLSIZE2(1) PLSIZE1(1) PLSIZE0(1) FSIZE4(1) FSIZE3(1) FSIZE2(1) FSIZE1(1) FSIZE0(1) bit 15 bit 8 U-0 R/W-1 R/W-1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — TXAT1 TXAT0 TXPRI4 TXPRI3 TXPRI2 TXPRI1 TXPRI0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-13 PLSIZE[2:0]: Payload Size bits(1) 111 = 64 data bytes 110 = 48 data bytes 101 = 32 data bytes 100 = 24 data bytes 011 = 20 data bytes 010 = 16 data bytes 001 = 12 data bytes 000 = 8 data bytes bit 12-8 FSIZE[4:0]: FIFO Size bits(1) 11111 = FIFO is 32 messages deep ... 00010 = FIFO is 3 messages deep 00001 = FIFO is 2 messages deep 00000 = FIFO is 1 message deep bit 7 Unimplemented: Read as ‘0’ bit 6-5 TXAT[1:0]: Retransmission Attempts bits This feature is enabled when RTXAT (C1CONH[0]) is set. 11 = Unlimited number of retransmission attempts 10 = Unlimited number of retransmission attempts 01 = Three retransmission attempts 00 = Disables retransmission attempts bit 4-0 TXPRI[4:0]: Message Transmit Priority bits 11111 = Highest message priority ... 00000 = Lowest message priority Note 1: 2: x = Bit is unknown These bits can only be modified in Configuration mode (OPMOD[2:0] = 100). CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 202  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-135: C1FIFOCONxL: CAN FIFO CONTROL REGISTER x (x = 1 TO 7) LOW(2) U-0 U-0 U-0 U-0 U-0 S/HC-1 R/W/HC-0 S/HC-0 — — — — — FRESET TXREQ UINC bit 15 bit 8 R/W-0 R/W-0 TXEN RTREN R/W-0 RXTSEN (1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TXATIE RXOVIE TFERFFIE TFHRFHIE TFNRFNIE bit 7 bit 0 Legend: S = Settable bit HC = Hardware Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-11 Unimplemented: Read as ‘0’ bit 10 FRESET: FIFO Reset bit 1 = FIFO will be reset when bit is set, cleared by hardware when FIFO is reset; user should poll whether this bit is clear before taking any action 0 = No effect bit 9 TXREQ: Message Send Request bit TXEN = 1 (FIFO configured as a transmit FIFO): 1 = Requests sending a message; the bit will automatically clear when all the messages queued in the FIFO are successfully sent 0 = Clearing the bit to ‘0’ while set (‘1’) will request a message abort TXEN = 0 (FIFO configured as a receive FIFO): This bit has no effect. bit 8 UINC: Increment Head/Tail bit TXEN = 1 (FIFO configured as a transmit FIFO): When this bit is set, the FIFO head will increment by a single message. TXEN = 0 (FIFO configured as a receive FIFO): When this bit is set, the FIFO tail will increment by a single message. bit 7 TXEN: TX/RX Buffer Selection bit 1 = Transmits message object 0 = Receives message object bit 6 RTREN: Auto-Remote Transmit (RTR) Enable bit 1 = When a Remote Transmit is received, TXREQ will be set 0 = When a Remote Transmit is received, TXREQ will be unaffected bit 5 RXTSEN: Received Message Timestamp Enable bit(1) 1 = Captures timestamp in received message object in RAM 0 = Does not capture timestamp bit 4 TXATIE: Transmit Attempts Exhausted Interrupt Enable bit 1 = Enables interrupt 0 = Disables interrupt bit 3 RXOVIE: Overflow Interrupt Enable bit 1 = Interrupt is enabled for overflow event 0 = Interrupt is disabled for overflow event Note 1: 2: This bit can only be modified in Configuration mode (OPMOD[2:0] = 100). CAN is available only on the dsPIC33CHXXXMP50X devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 203 dsPIC33CH128MP508 FAMILY REGISTER 3-135: C1FIFOCONxL: CAN FIFO CONTROL REGISTER x (x = 1 TO 7) LOW(2) (CONTINUED) bit 2 TFERFFIE: Transmit/Receive FIFO Empty/Full Interrupt Enable bit TXEN = 1 (FIFO configured as a transmit FIFO): Transmit FIFO Empty Interrupt Enable 1 = Interrupt is enabled for FIFO empty 0 = Interrupt is disabled for FIFO empty TXEN = 0 (FIFO configured as a receive FIFO): Receive FIFO Full Interrupt Enable 1 = Interrupt is enabled for FIFO full 0 = Interrupt is disabled for FIFO full bit 1 TFHRFHIE: Transmit/Receive FIFO Half Empty/Half Full Interrupt Enable bit TXEN = 1 (FIFO configured as a transmit FIFO): Transmit FIFO Half Empty Interrupt Enable 1 = Interrupt is enabled for FIFO half empty 0 = Interrupt is disabled for FIFO half empty TXEN = 0 (FIFO configured as a receive FIFO): Receive FIFO Half Full Interrupt Enable 1 = Interrupt is enabled for FIFO half full 0 = Interrupt is disabled for FIFO half full bit 0 TFNRFNIE: Transmit/Receive FIFO Not Full/Not Empty Interrupt Enable bit TXEN = 1 (FIFO configured as a transmit FIFO): Transmit FIFO Not Full Interrupt Enable 1 = Interrupt is enabled for FIFO not full 0 = Interrupt is disabled for FIFO not full TXEN = 0 (FIFO configured as a receive FIFO): Receive FIFO Not Empty Interrupt Enable 1 = Interrupt is enabled for FIFO not empty 0 = Interrupt is disabled for FIFO not empty Note 1: 2: This bit can only be modified in Configuration mode (OPMOD[2:0] = 100). CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 204  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-136: C1FIFOSTAx: CAN FIFO STATUS REGISTER x (x = 1 TO 7)(4) U-0 U-0 — U-0 — — R-0 FIFOCI4 R-0 (1) R-0 (1) FIFOCI3 R-0 (1) FIFOCI2 R-0 (1) FIFOCI1 FIFOCI0(1) bit 15 bit 8 R-0 TXABT (3) R-0 R-0 HS/C-0 HS/C-0 R-0 R-0 R-0 TXLARB(2) TXERR(2) TXATIF RXOVIF TFERFFIF TFHRFHIF TFNRFNIF bit 7 bit 0 Legend: C = Clearable bit HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-13 Unimplemented: Read as ‘0’ bit 12-8 FIFOCI[4:0]: FIFO Message Index bits(1) TXEN = 1 (FIFO configured as a transmit buffer): A read of this register will return an index to the message that the FIFO will next attempt to transmit. TXEN = 0 (FIFO configured as a receive buffer): A read of this register will return an index to the message that the FIFO will use to save the next message. bit 7 TXABT: Message Aborted Status bit(3) 1 = Message was aborted 0 = Message completed successfully bit 6 TXLARB: Message Lost Arbitration Status bit(2) 1 = Message lost arbitration while being sent 0 = Message did not lose arbitration while being sent bit 5 TXERR: Error Detected During Transmission bit(2) 1 = A bus error occurred while the message was being sent 0 = A bus error did not occur while the message was being sent bit 4 TXATIF: Transmit Attempts Exhausted Interrupt Pending bit TXEN = 1 (FIFO configured as a transmit buffer): 1 = Interrupt is pending 0 = Interrupt is not pending TXEN = 0 (FIFO configured as a receive buffer): Unused, read as ‘0’. bit 3 RXOVIF: Receive FIFO Overflow Interrupt Flag bit TXEN = 1 (FIFO configured as a transmit buffer): Unused, read as ‘0’. TXEN = 0 (FIFO configured as a receive buffer): 1 = Overflow event has occurred 0 = No overflow event has occurred Note 1: 2: 3: 4: FIFOCI[4:0] gives a zero-indexed value to the message in the FIFO. If the FIFO is four messages deep (FSIZE[4:0] = 3), FIFOCIx will take on a value of 0 to 3, depending on the state of the FIFO. These bits are updated when a message completes (or aborts) or when the FIFO is reset. This bit is reset on any read of this register or when the TXQ is reset. The bits are cleared when TXREQ is set or using an SPI write. CAN is available only on the dsPIC33CHXXXMP50X devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 205 dsPIC33CH128MP508 FAMILY REGISTER 3-136: C1FIFOSTAx: CAN FIFO STATUS REGISTER x (x = 1 TO 7)(4) (CONTINUED) bit 2 TFERFFIF: Transmit/Receive FIFO Empty/Full Interrupt Flag bit TXEN = 1 (FIFO configured as a transmit FIFO): Transmit FIFO Empty Interrupt Flag 1 = FIFO is empty 0 = FIFO is not empty, at least one message is queued to be transmitted TXEN = 0 (FIFO configured as a receive FIFO): Receive FIFO Full Interrupt Flag 1 = FIFO is full 0 = FIFO is not full bit 1 TFHRFHIF: Transmit/Receive FIFO Half Empty/Half Full Interrupt Flag bit TXEN = 1 (FIFO configured as a transmit FIFO): Transmit FIFO Half Empty Interrupt Flag 1 = FIFO is  half full 0 = FIFO is > half full TXEN = 0 (FIFO configured as a receive FIFO): Receive FIFO Half Full Interrupt Flag 1 = FIFO is  half full 0 = FIFO is < half full bit 0 TFNRFNIF: Transmit/Receive FIFO Not Full/Not Empty Interrupt Flag bit TXEN = 1 (FIFO configured as a transmit FIFO): Transmit FIFO Not Full Interrupt Flag 1 = FIFO is not full 0 = FIFO is full TXEN = 0 (FIFO configured as a receive FIFO): Receive FIFO Not Empty Interrupt Flag 1 = FIFO is not empty, has at least one message 0 = FIFO is empty Note 1: 2: 3: 4: FIFOCI[4:0] gives a zero-indexed value to the message in the FIFO. If the FIFO is four messages deep (FSIZE[4:0] = 3), FIFOCIx will take on a value of 0 to 3, depending on the state of the FIFO. These bits are updated when a message completes (or aborts) or when the FIFO is reset. This bit is reset on any read of this register or when the TXQ is reset. The bits are cleared when TXREQ is set or using an SPI write. CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 206  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-137: C1TEFCONH: CAN TRANSMIT EVENT FIFO CONTROL REGISTER HIGH(2) U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FSIZE[4:0](1) bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-13 Unimplemented: Read as ‘0’ bit 12-8 FSIZE[4:0]: FIFO Size bits(1) 11111 = FIFO is 32 messages deep ... 00010 = FIFO is 3 messages deep 00001 = FIFO is 2 messages deep 00000 = FIFO is 1 message deep bit 7-0 Unimplemented: Read as ‘0’ Note 1: 2: x = Bit is unknown These bits can only be modified in Configuration mode (OPMOD[2:0] = 100). CAN is available only on the dsPIC33CHXXXMP50X devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 207 dsPIC33CH128MP508 FAMILY REGISTER 3-138: C1TEFCONL: CAN TRANSMIT EVENT FIFO CONTROL REGISTER LOW(2) U-0 U-0 U-0 U-0 U-0 S/HC-0 U-0 S/HC-0 — — — — — FRESET — UINC bit 15 bit 8 U-0 U-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 — — TEFTSEN(1) — TEFOVIE TEFFIE TEFHIE TEFNEIE bit 7 bit 0 Legend: S = Settable bit HC = Hardware Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-11 Unimplemented: Read as ‘0’ bit 10 FRESET: FIFO Reset bit 1 = FIFO will be reset when bit is set, cleared by hardware when FIFO is reset; the user should poll whether this bit is clear before taking any action 0 = No effect bit 9 Unimplemented: Read as ‘0’ bit 8 UINC: Increment Tail bit 1 = When this bit is set, the FIFO tail will increment by a single message 0 = FIFO tail will not increment bit 7-6 Unimplemented: Read as ‘0’ bit 5 TEFTSEN: Transmit Event FIFO Timestamp Enable bit(1) 1 = Timestamps elements in TEF 0 = Does not timestamp elements in TEF bit 4 Unimplemented: Read as ‘0’ bit 3 TEFOVIE: Transmit Event FIFO Overflow Interrupt Enable bit 1 = Interrupt is enabled for overflow event 0 = Interrupt is disabled for overflow event bit 2 TEFFIE: Transmit Event FIFO Full Interrupt Enable bit 1 = Interrupt is enabled for FIFO full 0 = Interrupt is disabled for FIFO full bit 1 TEFHIE: Transmit Event FIFO Half Full Interrupt Enable bit 1 = Interrupt is enabled for FIFO half full 0 = Interrupt is disabled for FIFO half full bit 0 TEFNEIE: Transmit Event FIFO Not Empty Interrupt Enable bit 1 = Interrupt is enabled for FIFO not empty 0 = Interrupt is disabled for FIFO not empty Note 1: 2: These bits can only be modified in Configuration mode (OPMOD[2:0] = 100). CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 208  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-139: C1TEFSTA: CAN TRANSMIT EVENT FIFO STATUS REGISTER(2) U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 S/HC-0 R-0 R-0 R-0 — — — — TEFOVIF TEFFIF(1) TEFHIF(1) TEFNEIF(1) bit 7 bit 0 Legend: HC = Hardware Clearable bit S = Settable by ‘1’ bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-4 Unimplemented: Read as ‘0’ bit 3 TEFOVIF: Transmit Event FIFO Overflow Interrupt Flag bit 1 = Overflow event has occurred 0 = No overflow event has occurred bit 2 TEFFIF: Transmit Event FIFO Full Interrupt Flag bit(1) 1 = FIFO is full 0 = FIFO is not full bit 1 TEFHIF: Transmit Event FIFO Half Full Interrupt Flag bit(1) 1 = FIFO is  half full 0 = FIFO is < half full bit 0 TEFNEIF: Transmit Event FIFO Not Empty Interrupt Flag bit(1) 1 = FIFO is not empty 0 = FIFO is empty Note 1: 2: x = Bit is unknown These bits are read-only and reflect the status of the FIFO. CAN is available only on the dsPIC33CHXXXMP50X devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 209 dsPIC33CH128MP508 FAMILY REGISTER 3-140: C1FIFOUAHx: CAN FIFO USER ADDRESS HIGH x (x = 1 TO 7) REGISTER(1,2) R-x R-x R-x R-x R-x R-x R-x R-x FIFOUA[31:24] bit 15 bit 8 R-x R-x R-x R-x R-x R-x R-x R-x FIFOUA[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: 2: x = Bit is unknown FIFOUA[31:16]: FIFO User Address bits TXEN = 1 (FIFO configured as a transmit buffer): A read of this register will return the address where the next message is to be written (FIFO head). TXEN = 0 (FIFO configured as a receive buffer): A read of this register will return the address where the next message is to be read (FIFO tail). This register is not ensured to read correctly in Configuration mode and should only be accessed when the module is not in Configuration mode. CAN is available only on the dsPIC33CHXXXMP50X devices. REGISTER 3-141: C1FIFOUALx: CAN FIFO USER ADDRESS LOW x (x = 1 TO 7) REGISTER(1,2) R-x R-x R-x R-x R-x R-x R-x R-x FIFOUA[15:8] bit 15 bit 8 R-x R-x R-x R-x R-x R-x R-x R-x FIFOUA[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: 2: x = Bit is unknown FIFOUA[15:0]: FIFO User Address bits TXEN = 1 (FIFO configured as a transmit buffer): A read of this register will return the address where the next message is to be written (FIFO head). TXEN = 0 (FIFO configured as a receive buffer): A read of this register will return the address where the next message is to be read (FIFO tail). This register is not ensured to read correctly in Configuration mode and should only be accessed when the module is not in Configuration mode. CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 210  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-142: C1TEFUAH: CAN TRANSMIT EVENT FIFO USER ADDRESS REGISTER HIGH(1,2) R-x R-x R-x R-x R-x R-x R-x R-x TEFUA[31:24] bit 15 bit 8 R-x R-x R-x R-x R-x R-x R-x R-x TEFUA[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: 2: x = Bit is unknown TEFUA[31:16]: Transmit Event FIFO User Address bits A read of this register will return the address where the next event is to be read (FIFO tail). This register is not ensured to read correctly in Configuration mode and should only be accessed when the module is not in Configuration mode. CAN is available only on the dsPIC33CHXXXMP50X devices. REGISTER 3-143: C1TEFUAL: CAN TRANSMIT EVENT FIFO USER ADDRESS REGISTER LOW(1,2) R-x R-x R-x R-x R-x R-x R-x R-x TEFUA[15:8] bit 15 bit 8 R-x R-x R-x R-x R-x R-x R-x R-x TEFUA[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: 2: x = Bit is unknown TEFUA[15:0]: Transmit Event FIFO User Address bits A read of this register will return the address where the next event is to be read (FIFO tail). This register is not ensured to read correctly in Configuration mode and should only be accessed when the module is not in Configuration mode. CAN is available only on the dsPIC33CHXXXMP50X devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 211 dsPIC33CH128MP508 FAMILY REGISTER 3-144: C1TXQUAH: CAN TRANSMIT QUEUE USER ADDRESS REGISTER HIGH(1,2) R-x R-x R-x R-x R-x R-x R-x R-x TXQUA[31:24] bit 15 bit 8 R-x R-x R-x R-x R-x R-x R-x R-x TXQUA[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: 2: x = Bit is unknown TXQUA[31:16]: TXQ User Address bits A read of this register will return the address where the next message is to be written (TXQ head). This register is not ensured to read correctly in Configuration mode and should only be accessed when the module is not in Configuration mode. CAN is available only on the dsPIC33CHXXXMP50X devices. REGISTER 3-145: C1TXQUAL: CAN TRANSMIT QUEUE USER ADDRESS REGISTER LOW(1,2) R-x R-x R-x R-x R-x R-x R-x R-x TXQUA[15:8] bit 15 bit 8 R-x R-x R-x R-x R-x R-x R-x R-x TXQUA[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: 2: x = Bit is unknown TXQUA[15:0]: TXQ User Address bits A read of this register will return the address where the next message is to be written (TXQ head). This register is not ensured to read correctly in Configuration mode and should only be accessed when the module is not in Configuration mode. CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 212  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-146: C1TRECH: CAN TRANSMIT/RECEIVE ERROR COUNT REGISTER HIGH(1) U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 R-1 R-0 R-0 R-0 R-0 R-0 — — TXBO TXBP RXBP TXWARN RXWARN EWARN bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-6 Unimplemented: Read as ‘0’ bit 5 TXBO: Transmitter in Error State Bus Off bit (TERRCNT[7:0] > 255) In Configuration mode, TXBO is set since the module is not on the bus. bit 4 TXBP: Transmitter in Error State Bus Passive bit (TERRCNT[7:0] > 127) bit 3 RXBP: Receiver in Error State Bus Passive bit (RERRCNT[7:0] > 127) bit 2 TXWARN: Transmitter in Error State Warning bit (128 > TERRCNT[7:0] > 95) bit 1 RXWARN: Receiver in Error State Warning bit (128 > RERRCNT[7:0] > 95) bit 0 EWARN: Transmitter or Receiver in Error State Warning bit Note 1: CAN is available only on the dsPIC33CHXXXMP50X devices. REGISTER 3-147: C1TRECL: CAN TRANSMIT/RECEIVE ERROR COUNT REGISTER LOW(1) R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 TERRCNT[7:0] bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 RERRCNT[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-8 TERRCNT[7:0]: Transmit Error Counter bits bit 7-0 RERRCNT[7:0]: Receive Error Counter bits Note 1: x = Bit is unknown CAN is available only on the dsPIC33CHXXXMP50X devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 213 dsPIC33CH128MP508 FAMILY REGISTER 3-148: C1BDIAG0H: CAN BUS DIAGNOSTICS REGISTER 0 HIGH(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DTERRCNT[7:0] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DRERRCNT[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-8 DTERRCNT[7:0]: Data Bit Rate Transmit Error Counter bits bit 7-0 DRERRCNT[7:0]: Data Bit Rate Receive Error Counter bits Note 1: x = Bit is unknown CAN is available only on the dsPIC33CHXXXMP50X devices. REGISTER 3-149: C1BDIAG0L: CAN BUS DIAGNOSTICS REGISTER 0 LOW(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 NTERRCNT[7:0] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 NRERRCNT[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-8 NTERRCNT[7:0]: Nominal Bit Rate Transmit Error Counter bits bit 7-0 NRERRCNT[7:0]: Nominal Bit Rate Receive Error Counter bits Note 1: x = Bit is unknown CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 214  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-150: C1BDIAG1H: CAN BUS DIAGNOSTICS REGISTER 1 HIGH(1) R/W-0 R/W-0 R/C-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 DLCMM ESI DCRCERR DSTUFERR DFORMERR — DBIT1ERR DBIT0ERR bit 15 bit 8 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TXBOERR — NCRCERR NSTUFERR NFORMERR NACKERR NBIT1ERR NBIT0ERR bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 DLCMM: DLC Mismatch bit During a transmission or reception, the specified DLC is larger than the PLSIZE[2:0] of the FIFO element. bit 14 ESI: ESI Flag of a Received CAN FD Message Set bit bit 13 DCRCERR: Same as for nominal bit rate bit 12 DSTUFERR: Same as for nominal bit rate bit 11 DFORMERR: Same as for nominal bit rate bit 10 Unimplemented: Read as ‘0’ bit 9 DBIT1ERR: Same as for nominal bit rate bit 8 DBIT0ERR: Same as for nominal bit rate bit 7 TXBOERR: Device Went to Bus Off bit (and auto-recovered) bit 6 Unimplemented: Read as ‘0’ bit 5 NCRCERR: Received Message with CRC Incorrect Checksum bit The CRC checksum of a received message was incorrect. The CRC of an incoming message does not match with the CRC calculated from the received data. bit 4 NSTUFERR: Received Message with Illegal Sequence bit More than 5 equal bits in a sequence have occurred in a part of a received message where this is not allowed. bit 3 NFORMERR: Received Frame Fixed Format bit A fixed format part of a received frame has the wrong format. bit 2 NACKERR: Transmitted Message Not Acknowledged bit Transmitted message was not acknowledged. bit 1 NBIT1ERR: Transmitted Message Recessive Level bit During the transmission of a message (with the exception of the arbitration field), the device wanted to send a recessive level (bit of logical value ‘1’), but the monitored bus value was dominant. bit 0 NBIT0ERR: Transmitted Message Dominant Level bit During the transmission of a message (or Acknowledge bit, active error flag or overload flag), the device wanted to send a dominant level (data or identifier bit of logical value ‘0’), but the monitored bus value was recessive. During bus off recovery, this status is set each time a sequence of 11 recessive bits has been monitored. This enables the CPU to monitor the proceeding of the bus off recovery sequence (indicating the bus is not stuck at dominant or continuously disturbed). Note 1: CAN is available only on the dsPIC33CHXXXMP50X devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 215 dsPIC33CH128MP508 FAMILY REGISTER 3-151: C1BDIAG1L: CAN BUS DIAGNOSTICS REGISTER 1 LOW(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 EFMSGCNT[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 EFMSGCNT[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 EFMSGCNT[15:0]: Error-Free Message Counter bits Note 1: CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 216 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-152: C1FLTCONxH: CAN FILTER CONTROL REGISTER x HIGH (x = 0 TO 3; c = 2, 6, 10, 14; d = 3, 7, 11, 15)(1) R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FLTENd — — FdBP4 FdBP3 FdBP2 FdBP1 FdBP0 bit 15 bit 8 R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FLTENc — — FcBP4 FcBP3 FcBP2 FcBP1 FcBP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 FLTENd: Enable Filter d to Accept Messages bit 1 = Filter is enabled 0 = Filter is disabled bit 14-13 Unimplemented: Read as ‘0’ bit 12-8 FdBP[4:0]: Pointer to Object When Filter d Hits bits 11111 to 11000 = Reserved 00111 = Message matching filter is stored in Object 7 00110 = Message matching filter is stored in Object 6 ... 00010 = Message matching filter is stored in Object 2 00001 = Message matching filter is stored in Object 1 00000 = Reserved; Object 0 is the TX Queue and can’t receive messages bit 7 FLTENc: Enable Filter c to Accept Messages bit 1 = Filter is enabled 0 = Filter is disabled bit 6-5 Unimplemented: Read as ‘0’ bit 4-0 FcBP[4:0]: Pointer to Object When Filter c Hits bits 11111 to 11000 = Reserved 00111 = Message matching filter is stored in Object 7 00110 = Message matching filter is stored in Object 6 ... 00010 = Message matching filter is stored in Object 2 00001 = Message matching filter is stored in Object 1 00000 = Reserved; Object 0 is the TX Queue and can’t receive messages Note 1: CAN is available only on the dsPIC33CHXXXMP50X devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 217 dsPIC33CH128MP508 FAMILY REGISTER 3-153: C1FLTCONxL: CAN FILTER CONTROL REGISTER x LOW (x = 0 TO 3; a = 0, 4, 8, 12; b = 1, 5, 9, 13)(1) R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FLTENb — — FbBP4 FbBP3 FbBP2 FbBP1 FbBP0 bit 15 bit 8 R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FLTENa — — FaBP4 FaBP3 FaBP2 FaBP1 FaBP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 FLTENb: Enable Filter b to Accept Messages bit 1 = Filter is enabled 0 = Filter is disabled bit 14-13 Unimplemented: Read as ‘0’ bit 12-8 FbBP[4:0]: Pointer to Object When Filter b Hits bits 11111 to 11000 = Reserved 00111 = Message matching filter is stored in Object 7 00110 = Message matching filter is stored in Object 6 ... 00010 = Message matching filter is stored in Object 2 00001 = Message matching filter is stored in Object 1 00000 = Reserved; Object 0 is the TX Queue and can’t receive messages bit 7 FLTENa: Enable Filter a to Accept Messages bit 1 = Filter is enabled 0 = Filter is disabled bit 6-5 Unimplemented: Read as ‘0’ bit 4-0 FaBP[4:0]: Pointer to Object When Filter a Hits bits 11111 to 11000 = Reserved 00111 = Message matching filter is stored in Object 7 00110 = Message matching filter is stored in Object 6 ... 00010 = Message matching filter is stored in Object 2 00001 = Message matching filter is stored in Object 1 00000 = Reserved; Object 0 is the TX Queue and can’t receive messages Note 1: CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 218  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-154: C1FLTOBJxH: CAN FILTER OBJECT REGISTER x HIGH (x = 0 TO 15)(1) U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — EXIDE SID11 EID17 EID16 EID15 EID14 EID13 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 EID12 EID11 EID10 EID9 EID8 EID7 EID6 EID5 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14 EXIDE: Extended Identifier Enable bit If MIDE = 1: 1 = Matches only messages with Extended Identifier addresses 0 = Matches only messages with Standard Identifier addresses bit 13 SID11: Standard Identifier Filter bit bit 12-0 EID[17:5]: Extended Identifier Filter bits In DeviceNet™ mode, these are the filter bits for the first two data bytes. Note 1: CAN is available only on the dsPIC33CHXXXMP50X devices. REGISTER 3-155: C1FLTOBJxL: CAN FILTER OBJECT REGISTER x LOW (x = 0 TO 15)(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 EID4 EID3 EID2 EID1 EID0 SID10 SID9 SID8 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SID7 SID6 SID5 SID4 SID3 SID2 SID1 SID0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-11 EID[4:0]: Extended Identifier Filter bits In DeviceNet™ mode, these are the filter bits for the first two data bytes. bit 10-0 SID[10:0]: Standard Identifier Filter bits Note 1: x = Bit is unknown CAN is available only on the dsPIC33CHXXXMP50X devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 219 dsPIC33CH128MP508 FAMILY REGISTER 3-156: C1MASKxH: CAN MASK REGISTER x HIGH (x = 0 TO 15)(1) U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — MIDE MSID11 MEID17 MEID16 MEID15 MEID14 MEID13 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 MEID12 MEID11 MEID10 MEID9 MEID8 MEID7 MEID6 MEID5 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14 MIDE: Identifier Receive Mode bit 1 = Matches only message types (standard or extended address) that correspond to the EXIDE bit in the filter 0 = Matches either standard or extended address message if filters match (i.e., if (Filter SID) = (Message SID) or if (Filter SID/EID) = (Message SID/EID)) bit 13 MSID11: Standard Identifier Mask bit bit 12-0 MEID[17:5]: Extended Identifier Mask bits In DeviceNet™ mode, these are the mask bits for the first two data bytes. Note 1: CAN is available only on the dsPIC33CHXXXMP50X devices. REGISTER 3-157: C1MASKxL: CAN MASK REGISTER x LOW (x = 0 TO 15)(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 MEID4 MEID3 MEID2 MEID1 MEID0 MSID10 MSID9 MSID8 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 MSID7 MSID6 MSID5 MSID4 MSID3 MSID2 MSID1 MSID0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-11 MEID[4:0]: Extended Identifier Mask bits In DeviceNet™ mode, these are the mask bits for the first two data bytes. bit 10-0 MSID[10:0]: Standard Identifier Mask bits Note 1: CAN is available only on the dsPIC33CHXXXMP50X devices. DS70005319D-page 220  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.9 High-Speed, 12-Bit Analog-to-Digital Converter (Master ADC) Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “12-Bit High-Speed, Multiple SARs A/D Converter (ADC)” (www.microchip.com/DS70005213) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). 2: This section describes the Master ADC module, which implements one shared core and no dedicated cores. dsPIC33CH128MP508 devices have a high-speed, 12-bit Analog-to-Digital Converter (ADC) that features a low conversion latency, high resolution and oversampling capabilities to improve performance in AC/ DC and DC/DC power converters. The Master implements one SAR core ADC. 3.9.1 MASTER ADC FEATURES OVERVIEW The high-speed, 12-bit multiple SARs Analog-to-Digital Converter (ADC) includes the following features: • One Shared (common) Core • User-Configurable Resolution of up to 12 Bits • Up to 3.5 Msps Conversion Rate per Channel at 12-Bit Resolution • Low Latency Conversion • Up to 20 Analog Input Channels, with a Separate 16-Bit Conversion Result Register for each Input Channel • Conversion Result can be Formatted as Unsigned or Signed Data, on a per Channel Basis, for All Channels  2017-2019 Microchip Technology Inc. • Channel Scan Capability • Multiple Conversion Trigger Options, including: - PWM triggers from Master and Slave CPU cores - SCCP modules triggers - CLC modules triggers - External pin trigger event (ADTRG31) - Software trigger • Four Integrated Digital Comparators with Dedicated Interrupts: - Multiple comparison options - Assignable to specific analog inputs • Four Oversampling Filters with Dedicated Interrupts: - Provide increased resolution - Assignable to a specific analog input Simplified block diagrams of the 12-bit ADC are shown in Figure 3-24 and Figure 3-25. The analog inputs (channels) are connected through multiplexers and switches to the Sample-and-Hold (S&H) circuit of the ADC core. The core uses the channel information (the output format, the Measurement mode and the input number) to process the analog sample. When conversion is complete, the result is stored in the result buffer for the specific analog input, and passed to the digital filter and digital comparator if they were configured to use data from this particular channel. The ADC provides each analog input the ability to specify its own trigger source. This capability allows the ADC to sample and convert analog inputs that are associated with PWM generators operating on independent time bases. DS70005319D-page 221 dsPIC33CH128MP508 FAMILY FIGURE 3-24: ADC MODULE BLOCK DIAGRAM AVDD AVSS Voltage Reference (REFSEL[2:0]) Digital Comparator 0 Digital Comparator 1 Digital Comparator 2 Digital Comparator 3 AN15 ... SPGA3 (AN18) ADCMP2 Interrupt ADCMP3 Interrupt ADFL0DAT Digital Filter 1 ADFL1DAT Digital Filter 2 ADFL2DAT Digital Filter 3 ADFL3DAT ADCBUF20 ADFLTR0 Interrupt ADFLTR1 Interrupt ADFLTR2 Interrupt ADFLTR3 Interrupt ADCAN0 Interrupt ADCAN1 Interrupt ADCAN20 Interrupt Reference Output Data SPGA1 (AN16) SPGA2 (AN17) ADCMP1 Interrupt Digital Filter 0 ADCBUF0 ADCBUF1 AN0 ADCMP0 Interrupt Shared ADC Core Clock Divider (CLKDIV[5:0]) Temperature Sensor (AN19) Band Gap 1.2V (AN20) Clock Selection (CLKSEL[1:0]) FVCO/4 AFVCODIV FP (FOSC/2) Fosc Note: SPGA1, SPGA2 and SPGA3 are internal analog inputs and are not available on device pins. DS70005319D-page 222  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 3-25: SHARED CORE BLOCK DIAGRAM .. AN0 AN15 SPGA1 (AN16) + SPGA2 (AN17) Shared Sampleand-Hold SPGA3 (AN18) Temperature Sensor (AN19) Band Gap 1.2V (AN20) 12-Bit SAR ADC Analog Channel Number from Current Trigger ADC Core Clock Divider – Sampling Time Reference Output Data Clock SHRADCS[6:0] SHRSAMC[9:0] AVSS 3.9.2 TEMPERATURE SENSOR The ADC channel, AN19, is connected to a forward biased diode; it can be used to measure die temperature. This diode provides an output with a temperature coefficient of approximately -1.5 mV/C that can be monitored by the ADC. To get the exact gain and offset numbers, two-point temperature calibration is recommended. 3.9.3 ANALOG-TO-DIGITAL CONVERTER RESOURCES Many useful resources are provided on the main product page of the Microchip website for the devices listed in this data sheet. This product page contains the latest updates and additional information.  2017-2019 Microchip Technology Inc. 3.9.3.1 Key Resources • “12-Bit High-Speed, Multiple SARs A/D Converter (ADC)” (www.microchip.com/ DS70005213) in the “dsPIC33/PIC24 Family Reference Manual” • Code Samples • Application Notes • Software Libraries • Webinars • All Related “dsPIC33/PIC24 Family Reference Manual” Sections • Development Tools DS70005319D-page 223 dsPIC33CH128MP508 FAMILY 3.9.4 ADC CONTROL/STATUS REGISTERS REGISTER 3-158: ADCON1L: ADC CONTROL REGISTER 1 LOW R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0 ADON(1) — ADSIDL — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 ADON: ADC Enable bit(1) 1 = ADC module is enabled 0 = ADC module is off bit 14 Unimplemented: Read as ‘0’ bit 13 ADSIDL: ADC Stop in Idle Mode bit 1 = Discontinues module operation when device enters Idle mode 0 = Continues module operation in Idle mode bit 12-0 Unimplemented: Read as ‘0’ Note 1: x = Bit is unknown Set the ADON bit only after the ADC module has been configured. Changing ADC Configuration bits when ADON = 1 will result in unpredictable behavior. DS70005319D-page 224  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-159: ADCON1H: ADC CONTROL REGISTER 1 HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-0 R/W-1 R/W-1 U-0 U-0 U-0 U-0 U-0 FORM SHRRES1 SHRRES0 — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-8 Unimplemented: Read as ‘0’ bit 7 FORM: Fractional Data Output Format bit 1 = Fractional 0 = Integer bit 6-5 SHRRES[1:0]: Shared ADC Core Resolution Selection bits 11 = 12-bit resolution 10 = 10-bit resolution 01 = 8-bit resolution 00 = 6-bit resolution bit 4-0 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 225 dsPIC33CH128MP508 FAMILY REGISTER 3-160: ADCON2L: ADC CONTROL REGISTER 2 LOW R/W-0 R/W-0 U-0 R/W-0 R/W-0 REFCIE REFERCIE — EIEN PTGEN R/W-0 R/W-0 R/W-0 SHREISEL2(1) SHREISEL1(1) SHREISEL0(1) bit 15 bit 8 U-0 R/W-0 R/W-0 — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SHRADCS[6:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 REFCIE: Band Gap and Reference Voltage Ready Common Interrupt Enable bit 1 = Common interrupt will be generated when the band gap becomes ready 0 = Common interrupt is disabled for the band gap ready event bit 14 REFERCIE: Band Gap or Reference Voltage Error Common Interrupt Enable bit 1 = Common interrupt will be generated when a band gap or reference voltage error is detected 0 = Common interrupt is disabled for the band gap and reference voltage error event bit 13 Unimplemented: Read as ‘0’ bit 12 EIEN: Early Interrupts Enable bit 1 = The early interrupt feature is enabled for the input channel interrupts (when the EISTATx flag is set) 0 = The individual interrupts are generated when conversion is done (when the ANxRDY flag is set) bit 11 PTGEN: External Conversion Request Interface bit Setting this bit will enable the PTG to request conversion of an ADC input. bit 10-8 SHREISEL[2:0]: Shared Core Early Interrupt Time Selection bits(1) 111 = Early interrupt is set and interrupt is generated 8 TADCORE clocks prior to when the data are ready 110 = Early interrupt is set and interrupt is generated 7 TADCORE clocks prior to when the data are ready 101 = Early interrupt is set and interrupt is generated 6 TADCORE clocks prior to when the data are ready 100 = Early interrupt is set and interrupt is generated 5 TADCORE clocks prior to when the data are ready 011 = Early interrupt is set and interrupt is generated 4 TADCORE clocks prior to when the data are ready 010 = Early interrupt is set and interrupt is generated 3 TADCORE clocks prior to when the data are ready 001 = Early interrupt is set and interrupt is generated 2 TADCORE clocks prior to when the data are ready 000 = Early interrupt is set and interrupt is generated 1 TADCORE clock prior to when the data are ready bit 7 Unimplemented: Read as ‘0’ bit 6-0 SHRADCS[6:0]: Shared ADC Core Input Clock Divider bits These bits determine the number of TCORESRC (Source Clock Periods) for one shared TADCORE (Core Clock Period). 1111111 = 254 Source Clock Periods ... 0000011 = 6 Source Clock Periods 0000010 = 4 Source Clock Periods 0000001 = 2 Source Clock Periods 0000000 = 2 Source Clock Periods Note 1: For the 6-bit shared ADC core resolution (SHRRES[1:0] = 00), the SHREISEL[2:0] settings, from ‘100’ to ‘111’, are not valid and should not be used. For the 8-bit shared ADC core resolution (SHRRES[1:0] = 01), the SHREISEL[2:0] settings, ‘110’ and ‘111’, are not valid and should not be used. DS70005319D-page 226  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-161: ADCON2H: ADC CONTROL REGISTER 2 HIGH HSC/R-0 HSC/R-0 U-0 r-0 r-0 r-0 REFRDY REFERR — — — — R/W-0 bit 15 bit 8 R/W-0 SHRSAMC7 R/W-0 SHRSAMC9 SHRSAMC8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SHRSAMC6 SHRSAMC5 SHRSAMC4 SHRSAMC3 SHRSAMC2 SHRSAMC1 SHRSAMC0 bit 7 bit 0 Legend: r = Reserved bit U = Unimplemented bit, read as ‘0’ R = Readable bit W = Writable bit HSC = Hardware Settable/Clearable bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 REFRDY: Band Gap and Reference Voltage Ready Flag bit 1 = Band gap is ready 0 = Band gap is not ready bit 14 REFERR: Band Gap or Reference Voltage Error Flag bit 1 = Band gap was removed after the ADC module was enabled (ADON = 1) 0 = No band gap error was detected bit 13 Unimplemented: Read as ‘0’ bit 12-10 Reserved: Maintain as ‘0’ bit 9-0 SHRSAMC[9:0]: Shared ADC Core Sample Time Selection bits These bits specify the number of shared ADC Core Clock Periods (TADCORE) for the shared ADC core sample time (Sample Time = (SHRSAMC[9:0] + 2) * TADCORE). 1111111111 = 1025 TADCORE ... 0000000001 = 3 TADCORE 0000000000 = 2 TADCORE  2017-2019 Microchip Technology Inc. DS70005319D-page 227 dsPIC33CH128MP508 FAMILY REGISTER 3-162: ADCON3L: ADC CONTROL REGISTER 3 LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 HSC/R-0 R/W-0 HSC/R-0 REFSEL2 REFSEL1 REFSEL0 SUSPEND SUSPCIE SUSPRDY SHRSAMP CNVRTCH bit 15 bit 8 R/W-0 HSC/R-0 SWLCTRG SWCTRG R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: U = Unimplemented bit, read as ‘0’ R = Readable bit W = Writable bit HSC = Hardware Settable/Clearable bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-13 R/W-0 CNVCHSEL5 CNVCHSEL4 CNVCHSEL3 CNVCHSEL2 CNVCHSEL1 CNVCHSEL0 x = Bit is unknown REFSEL[2:0]: ADC Reference Voltage Selection bits Value VREFH VREFL 000 AVDD AVSS 001-111 = Unimplemented: Do not use bit 12 SUSPEND: All ADC Core Triggers Disable bit 1 = All new trigger events for all ADC cores are disabled 0 = All ADC cores can be triggered bit 11 SUSPCIE: Suspend All ADC Cores Common Interrupt Enable bit 1 = Common interrupt will be generated when ADC core triggers are suspended (SUSPEND bit = 1) and all previous conversions are finished (SUSPRDY bit becomes set) 0 = Common interrupt is not generated for suspend ADC cores event bit 10 SUSPRDY: All ADC Cores Suspended Flag bit 1 = ADC core is suspended (SUSPEND bit = 1) and has no conversions in progress 0 = ADC cores have previous conversions in progress bit 9 SHRSAMP: Shared ADC Core Sampling Direct Control bit This bit should be used with the individual channel conversion trigger controlled by the CNVRTCH bit. It connects an analog input, specified by the CNVCHSEL[5:0] bits, to the shared ADC core and allows extending the sampling time. This bit is not controlled by hardware and must be cleared before the conversion starts (setting CNVRTCH to ‘1’). 1 = Shared ADC core samples an analog input specified by the CNVCHSEL[5:0] bits 0 = Sampling is controlled by the shared ADC core hardware bit 8 CNVRTCH: Software Individual Channel Conversion Trigger bit 1 = Single trigger is generated for an analog input specified by the CNVCHSEL[5:0] bits; when the bit is set, it is automatically cleared by hardware on the next instruction cycle 0 = Next individual channel conversion trigger can be generated bit 7 SWLCTRG: Software Level-Sensitive Common Trigger bit 1 = Triggers are continuously generated for all channels with the software; level-sensitive common trigger selected as a source in the ADTRIGnL and ADTRIGnH registers 0 = No software, level-sensitive common triggers are generated bit 6 SWCTRG: Software Common Trigger bit 1 = Single trigger is generated for all channels with the software; common trigger selected as a source in the ADTRIGnL and ADTRIGnH registers; when the bit is set, it is automatically cleared by hardware on the next instruction cycle 0 = Ready to generate the next software common trigger bit 5-0 CNVCHSEL [5:0]: Channel Number Selection for Software Individual Channel Conversion Trigger bits These bits define a channel to be converted when the CNVRTCH bit is set. DS70005319D-page 228  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-163: ADCON3H: ADC CONTROL REGISTER 3 HIGH R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CLKSEL1 CLKSEL0 CLKDIV5 CLKDIV4 CLKDIV3 CLKDIV2 CLKDIV1 CLKDIV0 bit 15 bit 8 R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 SHREN — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 CLKSEL[1:0]: ADC Module Clock Source Selection bits 11 = FVCO/4 10 = AFVCODIV 01 = FOSC 00 = FP (FOSC/2) bit 13-8 CLKDIV[5:0]: ADC Module Clock Source Divider bits The divider forms a TCORESRC clock used by all ADC cores (shared and dedicated), from the TSRC ADC module clock source, selected by the CLKSEL[1:0] bits. Then, each ADC core individually divides the TCORESRC clock to get a core-specific TADCORE clock using the ADCS[6:0] bits in the ADCORExH register or the SHRADCS[6:0] bits in the ADCON2L register. 111111 = 64 Source Clock Periods ... 000011 = 4 Source Clock Periods 000010 = 3 Source Clock Periods 000001 = 2 Source Clock Periods 000000 = 1 Source Clock Period bit 7 SHREN: Shared ADC Core Enable bit 1 = Shared ADC core is enabled 0 = Shared ADC core is disabled bit 6-0 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. DS70005319D-page 229 dsPIC33CH128MP508 FAMILY REGISTER 3-164: ADCON5L: ADC CONTROL REGISTER 5 LOW HSC/R-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 SHRRDY — — — — — — — bit 15 bit 8 R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 SHRPWR — — — — — — — bit 7 bit 0 Legend: U = Unimplemented bit, read as ‘0’ R = Readable bit W = Writable bit HSC = Hardware Settable/Clearable bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 SHRRDY: Shared ADC Core Ready Flag bit 1 = ADC core is powered and ready for operation 0 = ADC core is not ready for operation bit 14-8 Unimplemented: Read as ‘0’ bit 7 SHRPWR: Shared ADC Core Power Enable bit 1 = ADC core is powered 0 = ADC core is off bit 6-0 Unimplemented: Read as ‘0’ DS70005319D-page 230 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-165: ADCON5H: ADC CONTROL REGISTER 5 HIGH U-0 U-0 U-0 U-0 — — — — R/W-0 R/W-0 R/W-0 R/W-0 WARMTIME[3:0] bit 15 bit 8 R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 SHRCIE — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-12 Unimplemented: Read as ‘0’ bit 11-8 WARMTIME[3:0]: ADC Dedicated Core Power-up Delay bits These bits determine the power-up delay in the number of the Core Source Clock Periods (TCORESRC) for all ADC cores. 1111 = 32768 Source Clock Periods 1110 = 16384 Source Clock Periods 1101 = 8192 Source Clock Periods 1100 = 4096 Source Clock Periods 1011 = 2048 Source Clock Periods 1010 = 1024 Source Clock Periods 1001 = 512 Source Clock Periods 1000 = 256 Source Clock Periods 0111 = 128 Source Clock Periods 0110 = 64 Source Clock Periods 0101 = 32 Source Clock Periods 0100 = 16 Source Clock Periods 00xx = 16 Source Clock Periods bit 7 SHRCIE: Shared ADC Core Ready Common Interrupt Enable bit 1 = Common interrupt will be generated when ADC core is powered and ready for operation 0 = Common interrupt is disabled for an ADC core ready event bit 6-0 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. DS70005319D-page 231 dsPIC33CH128MP508 FAMILY REGISTER 3-166: ADLVLTRGL: ADC LEVEL-SENSITIVE TRIGGER CONTROL REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 LVLEN[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 LVLEN[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown LVLEN[15:0]: Level Trigger for Corresponding Analog Input Enable bits 1 = Input trigger is level-sensitive 0 = Input trigger is edge-sensitive REGISTER 3-167: ADLVLTRGH: ADC LEVEL-SENSITIVE TRIGGER CONTROL REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 LVLEN[20:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-5 Unimplemented: Read as ‘0’ bit 4-0 LVLEN[20:16]: Level Trigger for Corresponding Analog Input Enable bits 1 = Input trigger is level-sensitive 0 = Input trigger is edge-sensitive DS70005319D-page 232  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-168: ADEIEL: ADC EARLY INTERRUPT ENABLE REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 EIEN[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 EIEN[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown EIEN[15:0]: Early Interrupt Enable for Corresponding Analog Input bits 1 = Early interrupt is enabled for the channel 0 = Early interrupt is disabled for the channel REGISTER 3-169: ADEIEH: ADC EARLY INTERRUPT ENABLE REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 EIEN[20:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-5 Unimplemented: Read as ‘0’ bit 4-0 EIEN[20:16]: Early Interrupt Enable for Corresponding Analog Input bits 1 = Early interrupt is enabled for the channel 0 = Early interrupt is disabled for the channel  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 233 dsPIC33CH128MP508 FAMILY REGISTER 3-170: ADEISTATL: ADC EARLY INTERRUPT STATUS REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 EISTAT[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 EISTAT[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown EISTAT[15:0]: Early Interrupt Status for Corresponding Analog Input bits 1 = Early interrupt was generated 0 = Early interrupt was not generated since the last ADCBUFx read REGISTER 3-171: ADEISTATH: ADC EARLY INTERRUPT STATUS REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 EISTAT[20:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-5 Unimplemented: Read as ‘0’ bit 4-0 EISTAT[20:16]: Early Interrupt Status for Corresponding Analog Input bits 1 = Early interrupt was generated 0 = Early interrupt was not generated since the last ADCBUFx read DS70005319D-page 234  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-172: ADMOD0L: ADC INPUT MODE CONTROL REGISTER 0 LOW U-0 R/W-0 U-0 R/W-0 U-0 R/W-0 U-0 R/W-0 — SIGN7 — SIGN6 — SIGN5 — SIGN4 bit 15 bit 8 U-0 R/W-0 U-0 R/W-0 U-0 R/W-0 U-0 R/W-0 — SIGN3 — SIGN2 — SIGN1 — SIGN0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-1 (odd) x = Bit is unknown Unimplemented: Read as ‘0’ bit 14-0 (even) SIGNn (n = 7 to 0): Output Data Sign for Corresponding Analog Input bits 1 = Channel output data are signed 0 = Channel output data are unsigned REGISTER 3-173: ADMOD0H: ADC INPUT MODE CONTROL REGISTER 0 HIGH U-0 R/W-0 U-0 R/W-0 U-0 R/W-0 U-0 R/W-0 — SIGN15 — SIGN14 — SIGN13 — SIGN12 bit 15 bit 8 U-0 R/W-0 U-0 R/W-0 U-0 R/W-0 U-0 R/W-0 — SIGN11 — SIGN10 — SIGN9 — SIGN8 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-1 (odd) x = Bit is unknown Unimplemented: Read as ‘0’ bit 14-0 (even) SIGNn (n = 15 to 8): Output Data Sign for Corresponding Analog Input bits 1 = Channel output data are signed 0 = Channel output data are unsigned  2017-2019 Microchip Technology Inc. DS70005319D-page 235 dsPIC33CH128MP508 FAMILY REGISTER 3-174: ADMOD1L: ADC INPUT MODE CONTROL REGISTER 1 LOW U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — — SIGN20 bit 15 bit 8 U-0 R/W-0 U-0 R/W-0 U-0 R/W-0 U-0 R/W-0 — SIGN19 — SIGN18 — SIGN17 — SIGN16 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-9 Unimplemented: Read as ‘0’ bit 7-1 (odd) Unimplemented: Read as ‘0’ bit 8-0 (even) SIGNn (n = 20 to 16): Output Data Sign for Corresponding Analog Input bits 1 = Channel output data are signed 0 = Channel output data are unsigned DS70005319D-page 236  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-175: ADIEL: ADC INTERRUPT ENABLE REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 IE[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 IE[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown IE[15:0]: Common Interrupt Enable bits 1 = Common and individual interrupts are enabled for the corresponding channel 0 = Common and individual interrupts are disabled for the corresponding channel REGISTER 3-176: ADIEH: ADC INTERRUPT ENABLE REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 IE[20:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-5 Unimplemented: Read as ‘0’ bit 4-0 IE[20:16]: Common Interrupt Enable bits 1 = Common and individual interrupts are enabled for the corresponding channel 0 = Common and individual interrupts are disabled for the corresponding channel  2017-2019 Microchip Technology Inc. DS70005319D-page 237 dsPIC33CH128MP508 FAMILY REGISTER 3-177: ADSTATL: ADC DATA READY STATUS REGISTER LOW HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 AN[15:8]RDY bit 15 HSC/R-0 bit 8 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 AN[7:0]RDY bit 7 bit 0 Legend: U = Unimplemented bit, read as ‘0’ R = Readable bit W = Writable bit HSC = Hardware Settable/Clearable bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown AN[15:0]RDY: Common Interrupt Enable for Corresponding Analog Input bits 1 = Channel conversion result is ready in the corresponding ADCBUFx register 0 = Channel conversion result is not ready REGISTER 3-178: ADSTATH: ADC DATA READY STATUS REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 — — — HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 AN[20:16]RDY bit 7 bit 0 Legend: U = Unimplemented bit, read as ‘0’ R = Readable bit W = Writable bit HSC = Hardware Settable/Clearable bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-5 Unimplemented: Read as ‘0’ bit 4-0 AN[20:16]RDY: Common Interrupt Enable for Corresponding Analog Input bits 1 = Channel conversion result is ready in the corresponding ADCBUFx register 0 = Channel conversion result is not ready DS70005319D-page 238  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-179: ADTRIGnL AND ADTRIGnH: ADC CHANNEL TRIGGER n(x) SELECTION REGISTERS LOW AND HIGH (x = 0 TO 19; n = 0 TO 4) U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TRGSRC(x+1)[4:0] bit 15 bit 8 U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TRGSRCx[4:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-13 Unimplemented: Read as ‘0’ bit 12-8 TRGSRC(x+1)[4:0]: Trigger Source Selection for Corresponding Analog Input bits (TRGSRC1 to TRGSRC19 – Odd) 11111 = ADTRG31 (PPS input) 11110 = Master PTG 11101 = Slave CLC1 11100 = Master CLC1 11011 = Slave PWM8 Trigger 2 11010 = Slave PWM5 Trigger 2 11001 = Slave PWM3 Trigger 2 11000 = Slave PWM1 Trigger 2 10111 = Master SCCP4 input capture/output compare 10110 = Master SCCP3 input capture/output compare 10101 = Master SCCP2 input capture/output compare 10100 = Master SCCP1 input capture/output compare 10011 = Reserved 10010 = Reserved 10001 = Reserved 10000 = Reserved 01111 = Reserved 01110 = Reserved 01101 = Reserved 01100 = Reserved 01011 = Master PWM4 Trigger 2 01010 = Master PWM4 Trigger 1 01001 = Master PWM3 Trigger 2 01000 = Master PWM3 Trigger 1 00111 = Master PWM2 Trigger 2 00110 = Master PWM2 Trigger 1 00101 = Master PWM1 Trigger 2 00100 = Master PWM1 Trigger 1 00011 = Reserved 00010 = Level software trigger 00001 = Common software trigger 00000 = No trigger is enabled bit 7-5 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. DS70005319D-page 239 dsPIC33CH128MP508 FAMILY REGISTER 3-179: ADTRIGnL AND ADTRIGnH: ADC CHANNEL TRIGGER n(x) SELECTION REGISTERS LOW AND HIGH (x = 0 TO 19; n = 0 TO 4) (CONTINUED) bit 4-0 TRGSRCx[4:0]: Common Interrupt Enable for Corresponding Analog Input bits (TRGSRCx0 to TRGSRCx20 – Even) 11111 = ADTRG31 (PPS input) 11110 = Master PTG 11101 = Slave CLC1 11100 = Master CLC1 11011 = Slave PWM8 Trigger 2 11010 = Slave PWM5 Trigger 2 11001 = Slave PWM3 Trigger 2 11000 = Slave PWM1 Trigger 2 10111 = Master SCCP4 input capture/output compare 10110 = Master SCCP3 input capture/output compare 10101 = Master SCCP2 input capture/output compare 10100 = Master SCCP1 input capture/output compare 10011 = Reserved 10010 = Reserved 10001 = Reserved 10000 = Reserved 01111 = Reserved 01110 = Reserved 01101 = Reserved 01100 = Reserved 01011 = Master PWM4 Trigger 2 01010 = Master PWM4 Trigger 1 01001 = Master PWM3 Trigger 2 01000 = Master PWM3 Trigger 1 00111 = Master PWM2 Trigger 2 00110 = Master PWM2 Trigger 1 00101 = Master PWM1 Trigger 2 00100 = Master PWM1 Trigger 1 00011 = Reserved 00010 = Level software trigger 00001 = Common software trigger 00000 = No trigger is enabled DS70005319D-page 240  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-180: ADCMPxCON: ADC DIGITAL COMPARATOR x CONTROL REGISTER (x = 0, 1, 2, 3) U-0 U-0 U-0 — — — HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 CHNL[4:0] bit 15 bit 8 R/W-0 R/W-0 HC/HS/R-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CMPEN IE STAT BTWN HIHI HILO LOHI LOLO bit 7 bit 0 Legend: HC = Hardware Clearable bit U = Unimplemented bit, read as ‘0’ R = Readable bit W = Writable bit HSC = Hardware Settable/Clearable bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared HS = Hardware Settable bit bit 15-13 Unimplemented: Read as ‘0’ bit 12-8 CHNL[4:0]: Input Channel Number bits 11111 = Reserved ... 10101 = Reserved 10100 = Band gap, 1.2V (AN20) 10011 = Temperature sensor (AN19) 10010 = SPGA3 (AN18) 10001 = SPGA2 (AN17) 10000 = SPGA1 (AN16) 01111 = AN15 ... 00000 = AN0 bit 7 CMPEN: Comparator Enable bit 1 = Comparator is enabled 0 = Comparator is disabled and the STAT status bit is cleared bit 6 IE: Comparator Common ADC Interrupt Enable bit 1 = Common ADC interrupt will be generated if the comparator detects a comparison event 0 = Common ADC interrupt will not be generated for the comparator bit 5 STAT: Comparator Event Status bit This bit is cleared by hardware when the channel number is read from the CHNL[4:0] bits. 1 = A comparison event has been detected since the last read of the CHNL[4:0] bits 0 = A comparison event has not been detected since the last read of the CHNL[4:0] bits bit 4 BTWN: Between Low/High Comparator Event bit 1 = Generates a comparator event when ADCMPxLO ≤ ADCBUFx < ADCMPxHI 0 = Does not generate a digital comparator event when ADCMPxLO ≤ ADCBUFx < ADCMPxHI bit 3 HIHI: High/High Comparator Event bit 1 = Generates a digital comparator event when ADCBUFx ≥ ADCMPxHI 0 = Does not generate a digital comparator event when ADCBUFx ≥ ADCMPxHI bit 2 HILO: High/Low Comparator Event bit 1 = Generates a digital comparator event when ADCBUFx < ADCMPxHI 0 = Does not generate a digital comparator event when ADCBUFx < ADCMPxHI bit 1 LOHI: Low/High Comparator Event bit 1 = Generates a digital comparator event when ADCBUFx ≥ ADCMPxLO 0 = Does not generate a digital comparator event when ADCBUFx ≥ ADCMPxLO bit 0 LOLO: Low/Low Comparator Event bit 1 = Generates a digital comparator event when ADCBUFx < ADCMPxLO 0 = Does not generate a digital comparator event when ADCBUFx < ADCMPxLO  2017-2019 Microchip Technology Inc. DS70005319D-page 241 dsPIC33CH128MP508 FAMILY REGISTER 3-181: ADCMPxENL: ADC DIGITAL COMPARATOR x CHANNEL ENABLE REGISTER LOW (x = 0, 1, 2, 3) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CMPEN[15:8] bit 15 bit 8 R/W/0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CMPEN[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown CMPEN[15:0]: Comparator Enable for Corresponding Input Channel bits 1 = Conversion result for corresponding channel is used by the comparator 0 = Conversion result for corresponding channel is not used by the comparator REGISTER 3-182: ADCMPxENH: ADC DIGITAL COMPARATOR x CHANNEL ENABLE REGISTER HIGH (x = 0, 1, 2, 3) U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CMPEN[20:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-5 Unimplemented: Read as ‘0’ bit 4-0 CMPEN[20:16]: Comparator Enable for Corresponding Input Channel bits 1 = Conversion result for corresponding channel is used by the comparator 0 = Conversion result for corresponding channel is not used by the comparator DS70005319D-page 242  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-183: ADFLxCON: ADC DIGITAL FILTER x CONTROL REGISTER (x = 0, 1, 2, 3) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 HSC/R-0 FLEN MODE1 MODE0 OVRSAM2 OVRSAM1 OVRSAM0 IE RDY bit 15 bit 8 U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FLCHSEL[4:0] bit 7 bit 0 Legend: U = Unimplemented bit, read as ‘0’ R = Readable bit W = Writable bit HSC = Hardware Settable/Clearable bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 FLEN: Filter Enable bit 1 = Filter is enabled 0 = Filter is disabled and the RDY bit is cleared bit 14-13 MODE[1:0]: Filter Mode bits 11 = Averaging mode 10 = Reserved 01 = Reserved 00 = Oversampling mode bit 12-10 OVRSAM[2:0]: Filter Averaging/Oversampling Ratio bits If MODE[1:0] = 00: 111 = 128x (16-bit result in the ADFLxDAT register is in 12.4 format) 110 = 32x (15-bit result in the ADFLxDAT register is in 12.3 format) 101 = 8x (14-bit result in the ADFLxDAT register is in 12.2 format) 100 = 2x (13-bit result in the ADFLxDAT register is in 12.1 format) 011 = 256x (16-bit result in the ADFLxDAT register is in 12.4 format) 010 = 64x (15-bit result in the ADFLxDAT register is in 12.3 format) 001 = 16x (14-bit result in the ADFLxDAT register is in 12.2 format) 000 = 4x (13-bit result in the ADFLxDAT register is in 12.1 format) If MODE[1:0] = 11 (12-bit result in the ADFLxDAT register in all instances): 111 = 256x 110 = 128x 101 = 64x 100 = 32x 011 = 16x 110 = 8x 001 = 4x 000 = 2x bit 9 IE: Filter Common ADC Interrupt Enable bit 1 = Common ADC interrupt will be generated when the filter result will be ready 0 = Common ADC interrupt will not be generated for the filter bit 8 RDY: Oversampling Filter Data Ready Flag bit This bit is cleared by hardware when the result is read from the ADFLxDAT register. 1 = Data in the ADFLxDAT register are ready 0 = The ADFLxDAT register has been read and new data in the ADFLxDAT register are not ready bit 7-5 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. DS70005319D-page 243 dsPIC33CH128MP508 FAMILY REGISTER 3-183: ADFLxCON: ADC DIGITAL FILTER x CONTROL REGISTER (x = 0, 1, 2, 3) (CONTINUED) bit 4-0 FLCHSEL[4:0]: Oversampling Filter Input Channel Selection bits 11111 = Reserved ... 10101 = Reserved 10100 = Band gap, 1.2V (AN20) 10011 = Temperature sensor (AN19) 10010 = SPGA3 (AN18) 10001 = SPGA2 (AN17) 10000 = SPGA1 (AN16) 01111 = AN15 ... 00000 = AN0 DS70005319D-page 244  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.10 Peripheral Trigger Generator (PTG) Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “Peripheral Trigger Generator (PTG)” (www.microchip.com/ DS70000669) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com) Table 3-44 shows an overview of the PTG module. TABLE 3-44: PTG MODULE OVERVIEW No. of PTG Modules Identical (Modules) Master 1 NA Slave None NA The dsPIC33CH128MP508 family Peripheral Trigger Generator (PTG) module is a user-programmable sequencer that is capable of generating complex trigger signal sequences to coordinate the operation of other peripherals. The PTG module is designed to interface with the modules, such as an Analog-toDigital Converter (ADC), output compare and PWM modules, timers and interrupt controllers.  2017-2019 Microchip Technology Inc. 3.10.1 FEATURES • Behavior is Step Command-Driven: - Step commands are eight bits wide • Commands are Stored in a Step Queue: - Queue depth is parameterized (8-32 entries) - Programmable Step execution time (Step delay) • Supports the Command Sequence Loop: - Can be nested one-level deep - Conditional or unconditional loop - Two 16-bit loop counters • 16 Hardware Input Triggers: - Sensitive to either positive or negative edges, or a high or low level • One Software Input Trigger • Generates up to 32 Unique Output Trigger Signals • Generates Two Types of Trigger Outputs: - Individual - Broadcast • Strobed Output Port for Literal Data Values: - 5-bit literal write (literal part of a command) - 16-bit literal write (literal held in the PTGL0 register) • Generates up to Ten Unique Interrupt Signals • Two 16-Bit General Purpose Timers • Flexible Self-Contained Watchdog Timer (WDT) to Set an Upper Limit to Trigger Wait Time • Single-Step Command Capability in Debug mode • Selectable Clock (system, Pulse-Width Modulator (PWM) or ADC) • Programmable Clock Divider DS70005319D-page 245 dsPIC33CH128MP508 FAMILY FIGURE 3-26: PTG BLOCK DIAGRAM PTGHOLD PTGL0[15:0](2) PTGADJ Step Command PTGTxLIM[15:0](3) PTG General Purpose Timerx PTGCxLIM[15:0](4) PTGSDLIM[15:0] PTG Loop Counter x PTG Step Delay Timer PTGBTE[31:0](2) 16-Bit Data Bus PTGCST[15:0] Step Command PTGCON[15:0] Trigger Outputs PTGDIV[4:0] PTGCLK0 • • • PTGCLK7 Clock Inputs PTGCLK[2:0]  PTG Control Logic Step Command Trigger Inputs PTG Interrupts Step Command PTGI0 • • • PTGI15 PTGO0 • • • PTGO31 PTG0IF • • • PTG7IF Strobe Output[15:0] PTGQPTR[4:0] PTG Watchdog Timer(1) PTGQUE0 PTGWDTIF PTGQUE1 PTGQUE2 PTGQUE3 PTGQUE4 PTGQUE5 Command Decoder PTGQUE6 PTGQUE7 ... PTGSTEPIF PTGQUE15 Note 1: 2: 3: 4: This is a dedicated Watchdog Timer for the PTG module and is independent of the device Watchdog Timer. See Figure 4-11. See Figure 4-9. See Figure 4-2. DS70005319D-page 246  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 3.10.2 PTG CONTROL/STATUS REGISTERS REGISTER 3-184: PTGCST: PTG CONTROL/STATUS LOW REGISTER R/W-0 U-0 R/W-0 R/W-0 U-0 HC/R/W-0 R/W-0 R/W-0 PTGEN — PTGSIDL PTGTOGL — PTGSWT(2) PTGSSEN(3) PTGIVIS bit 15 bit 8 HC/R/W-0 HS/R/W-0 HS/HC/R/W-0 U-0 U-0 U-0 R/W-0 R/W-0 PTGSTRT PTGWDTO PTGBUSY — — — PTGITM1(1) PTGITM0(1) bit 7 bit 0 Legend: HC = Hardware Clearable bit HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 PTGEN: PTG Enable bit 1 = PTG is enabled 0 = PTG is disabled bit 14 Unimplemented: Read as ‘0’ bit 13 PTGSIDL: PTG Freeze in Debug Mode bit 1 = Halts PTG operation when device is Idle 0 = PTG operation continues when device is Idle bit 12 PTGTOGL: PTG Toggle Trigger Output bit 1 = Toggles state of TRIG output for each execution of PTGTRIG 0 = Generates a single TRIG pulse for each execution of PTGTRIG bit 11 Unimplemented: Read as ‘0’ bit 10 PTGSWT: PTG Software Trigger bit(2) 1 = If the PTG state machine is executing a “Wait for software trigger” Step command (OPTION[3:0] = 1010 or 1011), the command will complete and execution will continue 0 = No action other than to clear the bit bit 9 PTGSSEN: PTG Single-Step Command bit(3) 1 = Enables single Step when in Debug mode 0 = Disables single Step bit 8 PTGIVIS: PTG Counter/Timer Visibility bit 1 = Reading the PTGSDLIM, PTGCxLIM or PTGTxLIM registers returns the current values of their corresponding Counter/Timer registers (PTGSDLIM, PTGCxLIM and PTGTxLIM) 0 = Reading the PTGSDLIM, PTGCxLIM or PTGTxLIM registers returns the value of these Limit registers bit 7 PTGSTRT: PTG Start Sequencer bit 1 = Starts to sequentially execute the commands (Continuous mode) 0 = Stops executing the commands bit 6 PTGWDTO: PTG Watchdog Timer Time-out Status bit 1 = PTG Watchdog Timer has timed out 0 = PTG Watchdog Timer has not timed out bit 5 PTGBUSY: PTG State Machine Busy bit 1 = PTG is running on the selected clock source; no SFR writes are allowed to PTGCLK[2:0] or PTGDIV[4:0] 0 = PTG state machine is not running Note 1: 2: 3: These bits apply to the PTGWHI and PTGWLO commands only. This bit is only used with the PTGCTRL Step command software trigger option. The PTGSSEN bit may only be written when in Debug mode.  2017-2019 Microchip Technology Inc. DS70005319D-page 247 dsPIC33CH128MP508 FAMILY REGISTER 3-184: PTGCST: PTG CONTROL/STATUS LOW REGISTER (CONTINUED) bit 4-2 Unimplemented: Read as ‘0’ bit 1-0 PTGITM[1:0]: PTG Input Trigger Operation Selection bit(1) 11 = Single-level detect with Step delay not executed on exit of command (regardless of the PTGCTRL command) (Mode 3) 10 = Single-level detect with Step delay executed on exit of command (Mode 2) 01 = Continuous edge detect with Step delay not executed on exit of command (regardless of the PTGCTRL command) (Mode 1) 00 = Continuous edge detect with Step delay executed on exit of command (Mode 0) Note 1: 2: 3: These bits apply to the PTGWHI and PTGWLO commands only. This bit is only used with the PTGCTRL Step command software trigger option. The PTGSSEN bit may only be written when in Debug mode. DS70005319D-page 248  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-185: PTGCON: PTG CONTROL/STATUS HIGH REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGCLK2 PTGCLK1 PTGCLK0 PTGDIV4 PTGDIV3 PTGDIV2 PTGDIV1 PTGDIV0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 PTGPWD3 PTGPWD2 PTGPWD1 PTGPWD0 — PTGWDT2 PTGWDT1 PTGWDT0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-13 PTGCLK[2:0]: PTG Module Clock Source Selection bits 111 = Reserved 110 = PLL VCO DIV 4 output 101 = PTG module clock source will be SCCP7 100 = PTG module clock source will be SCCP8 011 = Input from Timer1 Clock pin, T1CK 010 = PTG module clock source will be ADC clock 001 = PTG module clock source will be FOSC 000 = PTG module clock source will be FOSC/2 (FP) bit 12-8 PTGDIV[4:0]: PTG Module Clock Prescaler (Divider) bits 11111 = Divide-by-32 11110 = Divide-by-31 ... 00001 = Divide-by-2 00000 = Divide-by-1 bit 7-4 PTGPWD[3:0]: PTG Trigger Output Pulse-Width (in PTG clock cycles) bits 1111 = All trigger outputs are 16 PTG clock cycles wide 1110 = All trigger outputs are 15 PTG clock cycles wide ... 0001 = All trigger outputs are 2 PTG clock cycles wide 0000 = All trigger outputs are 1 PTG clock cycle wide bit 3 Unimplemented: Read as ‘0’ bit 2-0 PTGWDT[2:0]: PTG Watchdog Timer Time-out Selection bits 111 = Watchdog Timer will time out after 512 PTG clocks 110 = Watchdog Timer will time out after 256 PTG clocks 101 = Watchdog Timer will time out after 128 PTG clocks 100 = Watchdog Timer will time out after 64 PTG clocks 011 = Watchdog Timer will time out after 32 PTG clocks 010 = Watchdog Timer will time out after 16 PTG clocks 001 = Watchdog Timer will time out after 8 PTG clocks 000 = Watchdog Timer is disabled  2017-2019 Microchip Technology Inc. DS70005319D-page 249 dsPIC33CH128MP508 FAMILY REGISTER 3-186: PTGBTE: PTG BROADCAST TRIGGER ENABLE LOW REGISTER(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGBTE[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGBTE[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: x = Bit is unknown PTGBTE[15:0]: PTG Broadcast Trigger Enable bits 1 = Generates trigger when the broadcast command is executed 0 = Does not generate trigger when the broadcast command is executed These bits are read-only when the module is executing Step commands. REGISTER 3-187: PTGBTEH: PTG BROADCAST TRIGGER ENABLE HIGH REGISTER(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGBTE[31:24] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGBTE[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: x = Bit is unknown PTGBTE[31:16]: PTG Broadcast Trigger Enable bits 1 = Generates trigger when the broadcast command is executed 0 = Does not generate trigger when the broadcast command is executed These bits are read-only when the module is executing Step commands. DS70005319D-page 250  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-188: PTGHOLD: PTG HOLD REGISTER(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGHOLD[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGHOLD[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: x = Bit is unknown PTGHOLD[15:0]: PTG General Purpose Hold Register bits This register holds the user-supplied data to be copied to the PTGTxLIM, PTGCxLIM, PTGSDLIM or PTGL0 register using the PTGCOPY command. These bits are read-only when the module is executing Step commands. REGISTER 3-189: PTGT0LIM: PTG TIMER0 LIMIT REGISTER(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGT0LIM[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGT0LIM[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: x = Bit is unknown PTGT0LIM[15:0]: PTG Timer0 Limit Register bits General Purpose Timer0 Limit register. These bits are read-only when the module is executing Step commands.  2017-2019 Microchip Technology Inc. DS70005319D-page 251 dsPIC33CH128MP508 FAMILY REGISTER 3-190: PTGT1LIM: PTG TIMER1 LIMIT REGISTER(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGT1LIM[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGT1LIM[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: x = Bit is unknown PTGT1LIM[15:0]: PTG Timer1 Limit Register bits General Purpose Timer1 Limit register. These bits are read-only when the module is executing Step commands. REGISTER 3-191: PTGSDLIM: PTG STEP DELAY LIMIT REGISTER(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGSDLIM[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGSDLIM[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: x = Bit is unknown PTGSDLIM[15:0]: PTG Step Delay Limit Register bits This register holds a PTG Step delay value representing the number of additional PTG clocks between the start of a Step command and the completion of a Step command. These bits are read-only when the module is executing Step commands. DS70005319D-page 252  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-192: PTGC0LIM: PTG COUNTER 0 LIMIT REGISTER(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGC0LIM[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGC0LIM[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: x = Bit is unknown PTGC0LIM[15:0]: PTG Counter 0 Limit Register bits This register is used to specify the loop count for the PTGJMPC0 Step command or as a Limit register for the General Purpose Counter 0. These bits are read-only when the module is executing Step commands. REGISTER 3-193: PTGC1LIM: PTG COUNTER 1 LIMIT REGISTER(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGC1LIM[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGC1LIM[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: x = Bit is unknown PTGC1LIM[15:0]: PTG Counter 1 Limit Register bits This register is used to specify the loop count for the PTGJMPC1 Step command or as a Limit register for the General Purpose Counter 1. These bits are read only when the module is executing step commands.  2017-2019 Microchip Technology Inc. DS70005319D-page 253 dsPIC33CH128MP508 FAMILY REGISTER 3-194: PTGADJ: PTG ADJUST REGISTER(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGADJ[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGADJ[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: x = Bit is unknown PTGADJ[15:0]: PTG Adjust Register bits This register holds the user-supplied data to be added to the PTGTxLIM, PTGCxLIM, PTGSDLIM or PTGL0 register using the PTGADD command. These bits are read-only when the module is executing Step commands. REGISTER 3-195: PTGL0: PTG LITERAL 0 REGISTER(1,2) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGL0[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGL0[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: 2: x = Bit is unknown PTGL0[15:0]: PTG Literal 0 Register bits This register holds the 6-bit value to be written to the CNVCHSEL[5:0] bits (ADCON3L[5:0]) with the PTGCTRL Step command. These bits are read-only when the module is executing Step commands. The PTG strobe output is typically connected to the ADC Channel Select register. This allows the PTG to directly control ADC channel switching. See the specific device data sheet for connections of the PTG output. DS70005319D-page 254  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 3-196: PTGQPTR: PTG STEP QUEUE POINTER REGISTER(1) U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PTGQPTR[4:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-5 Unimplemented: Read as ‘0’ bit 4-0 PTGQPTR[4:0]: PTG Step Queue Pointer Register bits This register points to the currently active Step command in the Step queue. Note 1: These bits are read only when the module is executing step commands. REGISTER 3-197: PTGQUEn: PTG STEP QUEUE n POINTER REGISTER (n = 0-15)(1,2) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 STEP2n+1[7:0] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 STEP2n[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 STEP2n+1[7:0]: PTG Command 4n+1 bits A queue location for storage of the STEP2n+1 command byte, where ‘n’ is from PTGQUEn. bit STEP2n[7:0]: PTG Command 4n+2 bits A queue location for storage of the STEP2n command byte, where ‘n’ are the odd numbered Step Queue Pointers. Note 1: 2: These bits are read-only when the module is executing Step commands. Refer to Table 3-1 for the Step command encoding.  2017-2019 Microchip Technology Inc. DS70005319D-page 255 dsPIC33CH128MP508 FAMILY TABLE 3-45: PTG STEP COMMAND FORMAT AND DESCRIPTION Step Command Byte STEPx[7:0] CMD[3:0] bit 7 bit 7-4 OPTION[3:0] bit 4 bit 3 Step Command CMD[3:0] bit 0 Command Description Execute the control command as described by the OPTION[3:0] bits. Add contents of the PTGADJ register to the target register as described by the OPTION[3:0] bits. PTGCOPY Copy contents of the PTGHOLD register to the target register as described by the OPTION[3:0] bits. PTGSTRB 001x Copy the values contained in the bits, CMD[0]:OPTION[3:0], to the strobe output bits[4:0]. PTGWHI 0100 Wait for a low-to-high edge input from a selected PTG trigger input as described by the OPTION[3:0] bits. PTGWLO 0101 Wait for a high-to-low edge input from a selected PTG trigger input as described by the OPTION[3:0] bits. — 0110 Reserved; do not use.(1) PTGIRQ 0111 Generate individual interrupt request as described by the OPTION[3:0] bits. PTGTRIG 100x Generate individual trigger output as described by the bits, CMD[0]:OPTION[3:0]. PTGJMP 101x Copy the values contained in the bits, CMD[0]:OPTION[3:0], to the PTGQPTR register and jump to that Step queue. PTGJMPC0 110x PTGC0 = PTGC0LIM: Increment the PTGQPTR register. PTGC0  PTGC0LIM: Increment Counter 0 (PTGC0) and copy the values contained in the bits, CMD[0]:OPTION[3:0], to the PTGQPTR register, and jump to that Step queue. PTGJMPC1 111x PTGC1 = PTGC1LIM: Increment the PTGQPTR register. PTGC1  PTGC1LIM: Increment Counter 1 (PTGC1) and copy the values contained in the bits, CMD[0]:OPTION[3:0], to the PTGQPTR register, and jump to that Step queue. Note 1: All reserved commands or options will execute, but they do not have any affect (i.e., execute as a NOP instruction). PTGCTRL PTGADD DS70005319D-page 256 0000 0001  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 3-46: bit 3-0 PTG COMMAND OPTIONS Step Command PTGWHI(1) or PTGWLO(1) PTGIRQ(1) OPTION[3:0] 0000 • • • • • • PTGI15 (see Table 3-47 for input assignments). 0000 Generate PTG Interrupt 0. • • • 0111 Generate PTG Interrupt 7. 1000 Reserved; do not use. • • • • • • 1111 Reserved; do not use. 0000 PTGO0 (see Table 3-48 for output assignments). 0001 PTGO1 (see Table 3-48 for output assignments). • • • Note 1: PTGI0 (see Table 3-47 for input assignments). 1111 • • • PTGTRIG Command Description • • • 1110 PTGO30 (see Table 3-48 for output assignments). 1111 PTGO31 (see Table 3-48 for output assignments). All reserved commands or options will execute, but they do not have any affect (i.e., execute as a NOP instruction).  2017-2019 Microchip Technology Inc. DS70005319D-page 257 dsPIC33CH128MP508 FAMILY TABLE 3-47: PTG INPUT DESCRIPTIONS PTG Input Number PTG Input Description PTG Trigger Input 0 Trigger Input from Master PWM Channel 1 PTG Trigger Input 1 Trigger Input from Master PWM Channel 2 PTG Trigger Input 2 Trigger Input from Master PWM Channel 3 PTG Trigger Input 3 Trigger Input from Master PWM Channel 4 PTG Trigger Input 4 Trigger Input from Slave PWM Channel 1 PTG Trigger Input 5 Trigger Input from Slave PWM Channel 2 PTG Trigger Input 6 Trigger Input from Slave PWM Channel 3 PTG Trigger Input 7 Trigger Input from Master SCCP4 IC/OC PTG Trigger Input 8 Trigger Input from Slave SCCP4 IC/OC PTG Trigger Input 9 Trigger Input from Master Comparator 1 PTG Trigger Input 10 Trigger Input from Slave Comparator 1 PTG Trigger Input 11 Trigger Input from Slave Comparator 2 PTG Trigger Input 12 Trigger Input from Slave Comparator 3 PTG Trigger Input 13 Trigger Input Master ADC Done Group Interrupt PTG Trigger Input 14 Trigger Input Slave ADC Done Group Interrupt PTG Trigger Input 15 Trigger Input from INT2 PPS TABLE 3-48: PTG OUTPUT DESCRIPTIONS PTG Output Number PTGO0 to PTGO11 PTG Output Description Reserved PTGO12 Trigger for Master ADC TRGSRC[30] PTGO13 Trigger for Slave ADC TRGSRC[30] PTGO16 to PTGO23 Reserved PTGO24 PPS Master Output RP46 PTGO25 PPS Master Output RP47 PTGO26 PPS Master Input RP6 PTGO27 PPS Master Input RP7 PTGO28 PPS Slave Output RP46 PTGO29 PPS Slave Output RP47 PTGO30 PPS Slave Input RP6 PTGO31 PPS Slave Input RP7 DS70005319D-page 258  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 4.0 SLAVE MODULES 4.1 Slave CPU Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “Enhanced CPU” (www.microchip.com/DS70005158) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). The Slave CPU fetches instructions from the PRAM (Program RAM Memory for the Slave). The Master core and Slave core can run independently asynchronously, at the same speed, or at a different speed. On a POR, the PRAM will not have the user code. The Master core will load the Slave code from the Master Flash to the Slave PRAM, and once the code is verified, the Master core will release the Slave core to start executing the code (SLVEN (MSI1CON[15] = 1). Note: All of the associated register names are the same on the Master as well as the Slave. The Slave code will be developed in a separate project in MPLAB® X IDE with the device selection, MP50XS1/20XS1, where S1 indicates the Slave device. The dsPIC33CH128MP508S1 family CPU has a 16-bit (data) modified Harvard architecture with an enhanced instruction set, including significant support for Digital Signal Processing (DSP). The CPU has a 24-bit instruction word with a variable length opcode field. The Program Counter (PC) is 23 bits wide and addresses up to 4M x 24 bits of user program memory space. 4.1.1 REGISTERS The dsPIC33CH128MP508S1 devices have sixteen, 16-bit Working registers in the programmer’s model. Each of the Working registers can act as a data, address or address offset register. The 16th Working register (W15) operates as a Software Stack Pointer for interrupts and calls. In addition, the dsPIC33CH128MP508S1 devices include four Alternate Working register sets, which consist of W0 through W14. The Alternate Working registers can be made persistent to help reduce the saving and restoring of register content during Interrupt Service Routines (ISRs). The Alternate Working registers can be assigned to a specific Interrupt Priority Level (IPL1 through IPL7) by configuring the CTXTx[2:0] bits in the FALTREG Configuration register. The Alternate Working registers can also be accessed manually by using the CTXTSWP instruction. The CCTXI[2:0] and MCTXI[2:0] bits in the CTXTSTAT register can be used to identify the current and most recent, manually selected Working register sets. 4.1.2 INSTRUCTION SET The instruction set for dsPIC33CH128MP508S1 devices has two classes of instructions: the MCU class of instructions and the DSP class of instructions. These two instruction classes are seamlessly integrated into the architecture and execute from a single execution unit. The instruction set includes many addressing modes and was designed for optimum C compiler efficiency. Note 1: Unlike the Master, there is no prefetch of the instruction implemented for the Slave. Most instructions execute in a single-cycle effective execution rate, with the exception of instructions that change the program flow, the double-word move (MOV.D) instruction, PSV accesses and the table instructions. Overhead-free program loop constructs are supported using the DO and REPEAT instructions, both of which are interruptible at any point.  2017-2019 Microchip Technology Inc. DS70005319D-page 259 dsPIC33CH128MP508 FAMILY 4.1.3 DATA SPACE ADDRESSING The base Data Space can be addressed as up to 4K words or 8 Kbytes, and is split into two blocks, referred to as X and Y data memory. Each memory block has its own independent Address Generation Unit (AGU). The MCU class of instructions operates solely through the X memory AGU, which accesses the entire memory map as one linear Data Space. Certain DSP instructions operate through the X and Y AGUs to support dual operand reads, which splits the data address space into two parts. The X and Y Data Space boundary is device-specific. The upper 32 Kbytes of the Data Space memory map can optionally be mapped into Program Space (PS) at any 16K program word boundary. The program-to-Data Space mapping feature, known as Program Space Visibility (PSV), lets any instruction access Program Space as if it were Data Space. Refer to “Data Memory” (DS70595) in the “dsPIC33/PIC24 Family Reference Manual” for more details on PSV and table accesses. 4.1.4 ADDRESSING MODES The CPU supports these addressing modes: • • • • • • Inherent (no operand) Relative Literal Memory Direct Register Direct Register Indirect Each instruction is associated with a predefined addressing mode group, depending upon its functional requirements. As many as six addressing modes are supported for each instruction. On dsPIC33CH128MP508S1 family devices, overheadfree circular buffers (Modulo Addressing) are supported in both X and Y address spaces. The Modulo Addressing removes the software boundary checking overhead for DSP algorithms. The X AGU Circular Addressing can be used with any of the MCU class of instructions. The X AGU also supports BitReversed Addressing to greatly simplify input or output data re-ordering for radix-2 FFT algorithms. DS70005319D-page 260  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 4-1: dsPIC33CH128MP508S1 FAMILY (SLAVE) CPU BLOCK DIAGRAM X Address Bus Y Data Bus X Data Bus Interrupt Controller PSV and Table Data Access 24 Control Block 8 Data Latch Data Latch Y Data RAM X Data RAM Address Latch Address Latch 16 Y Address Bus 24 24 PCU PCH PCL Program Counter Loop Stack Control Control Logic Logic Address Latch 16 16 16 16 16 16 24 16 X RAGU X WAGU 16 Y AGU PRAM Memory EA MUX 16 Data Latch Literal Data 24 24 16 IR ROM Latch 16 16 16-Bit Working Register Arrays 16 16 16 Divide Support DSP Engine 16-Bit ALU Control Signals to Various Blocks Instruction Decode and Control 16 Power, Reset and Oscillator Modules 16 Ports Peripheral Modules Master CPU  2017-2019 Microchip Technology Inc. MSI DS70005319D-page 261 dsPIC33CH128MP508 FAMILY 4.1.5 PROGRAMMER’S MODEL The programmer’s model for the dsPIC33CH128MP508S1 family is shown in Figure 4-2. All registers in the programmer’s model are memorymapped and can be manipulated directly by instructions. Table 4-1 lists a description of each register. TABLE 4-1: In addition to the registers contained in the programmer’s model, the dsPIC33CH128MP508S1 devices contain control registers for Modulo Addressing, Bit-Reversed Addressing and interrupts. These registers are described in subsequent sections of this document. All registers associated with the programmer’s model are memory-mapped, as shown in Figure 4-3. PROGRAMMER’S MODEL REGISTER DESCRIPTIONS Register(s) Name Description W0 through W15(1) Working Register Array W0 through W14(1) Alternate 1 Working Register Array W14(1) Alternate 2 Working Register Array W0 through W14(1) Alternate 3 Working Register Array (1) Alternate 4 Working Register Array W0 through W0 through W14 ACCA, ACCB 40-Bit DSP Accumulators (Additional 4 Alternate Accumulators) PC 23-Bit Program Counter SR ALU and DSP Engine STATUS Register SPLIM Stack Pointer Limit Value Register TBLPAG Table Memory Page Address Register DSRPAG Extended Data Space (EDS) Read Page Register RCOUNT REPEAT Loop Counter Register DCOUNT DO Loop Counter Register DOSTARTH(2), DOSTARTL(2) DO Loop Start Address Register (High and Low) DOENDH, DOENDL DO Loop End Address Register (High and Low) CORCON Contains DSP Engine, DO Loop Control and Trap Status bits Note 1: 2: Memory-mapped W0 through W14 represent the value of the register in the currently active CPU context. The DOSTARTH and DOSTARTL registers are read-only. DS70005319D-page 262  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 4-2: PROGRAMMER’S MODEL (SLAVE) D15 D0 D15 D0 D15 D0 D15 D0 D15 D0 W0 (WREG) W1 W0-W3 W0 W0 W0 W1 W1 W1 W4 W2 W3 W4 W2 W2 W2 W3 W3 W3 W4 W4 W4 W5 W5 W5 W5 W5 W6 W7 W6 W7 W8 W6 W7 W6 W6 W7 W7 W8 W8 W8 W9 W9 W9 W9 W2 W3 DSP Operand Registers Working/Address Registers W8 W9 DSP Address Registers W10 W10 W11 W11 W10 W10 W10 W11 W11 W11 W12 W12 W13 W13 Frame Pointer/W14 W14 Stack Pointer/W15 0 W12 W12 W12 W13 W13 W13 PUSH.S and POP.S Shadows SPLIM Nested DO Stack AD15 AD31 AD0 AD0 AD0 AD15 AD15 AD31 AD31 AD31 W14 W14 W14 AD31 AD39 AD39 Alternate Working/Address Registers Stack Pointer Limit 0 AD39 AD39 DSP Accumulators(1) W0 W1 AD15 AD0 AD0 AD15 AD31 ACCA ACCB PC23 PC0 0 0 Program Counter 0 7 TBLPAG Data Table Page Address 9 0 DSRPAG X Data Space Read Page Address 15 0 REPEAT Loop Counter RCOUNT 15 0 DCOUNT DO Loop Counter and Stack 23 0 DOSTART 0 0 DO Loop Start Address and Stack 23 0 DOEND 0 0 DO Loop End Address and Stack 15 0 CORCON CPU Core Control Register SRL OA OB SA SB OAB SAB  2017-2019 Microchip Technology Inc. DA DC IPL2 IPL1 IPL0 RA N OV Z C STATUS Register DS70005319D-page 263 dsPIC33CH128MP508 FAMILY 4.1.6 CPU RESOURCES Many useful resources are provided on the main product page of the Microchip website for the devices listed in this data sheet. This product page contains the latest updates and additional information. DS70005319D-page 264 4.1.6.1 Key Resources • “Enhanced CPU” (www.microchip.com/ DS70005158) in the “dsPIC33/PIC24 Family Reference Manual” • Code Samples • Application Notes • Software Libraries • Webinars • All related “dsPIC33/PIC24 Family Reference Manual” Sections • Development Tools  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 4.1.7 CPU CONTROL/STATUS REGISTERS REGISTER 4-1: SR: CPU STATUS REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/C-0 R/C-0 R-0 R/W-0 OA OB SA(3) SB(3) OAB SAB DA DC bit 15 bit 8 R/W-0(2) R/W-0(2) (1) IPL1 IPL2 (1) R/W-0(2) R-0 R/W-0 R/W-0 R/W-0 R/W-0 IPL0(1) RA N OV Z C bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’= Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 OA: Accumulator A Overflow Status bit 1 = Accumulator A has overflowed 0 = Accumulator A has not overflowed bit 14 OB: Accumulator B Overflow Status bit 1 = Accumulator B has overflowed 0 = Accumulator B has not overflowed bit 13 SA: Accumulator A Saturation ‘Sticky’ Status bit(3) 1 = Accumulator A is saturated or has been saturated at some time 0 = Accumulator A is not saturated bit 12 SB: Accumulator B Saturation ‘Sticky’ Status bit(3) 1 = Accumulator B is saturated or has been saturated at some time 0 = Accumulator B is not saturated bit 11 OAB: OA || OB Combined Accumulator Overflow Status bit 1 = Accumulator A or B has overflowed 0 = Neither Accumulator A or B has overflowed bit 10 SAB: SA || SB Combined Accumulator ‘Sticky’ Status bit 1 = Accumulator A or B is saturated or has been saturated at some time 0 = Neither Accumulator A or B is saturated bit 9 DA: DO Loop Active bit 1 = DO loop is in progress 0 = DO loop is not in progress bit 8 DC: MCU ALU Half Carry/Borrow bit 1 = A carry-out from the 4th low-order bit (for byte-sized data) or 8th low-order bit (for word-sized data) of the result occurred 0 = No carry-out from the 4th low-order bit (for byte-sized data) or 8th low-order bit (for word-sized data) of the result occurred Note 1: 2: 3: The IPL[2:0] bits are concatenated with the IPL[3] bit (CORCON[3]) to form the CPU Interrupt Priority Level. The value in parentheses indicates the IPL, if IPL[3] = 1. User interrupts are disabled when IPL[3] = 1. The IPL[2:0] Status bits are read-only when the NSTDIS bit (INTCON1[15]) = 1. A data write to the SR register can modify the SA and SB bits by either a data write to SA and SB or by clearing the SAB bit. To avoid a possible SA or SB bit write race condition, the SA and SB bits should not be modified using bit operations.  2017-2019 Microchip Technology Inc. DS70005319D-page 265 dsPIC33CH128MP508 FAMILY REGISTER 4-1: SR: CPU STATUS REGISTER (CONTINUED) bit 7-5 IPL[2:0]: CPU Interrupt Priority Level Status bits(1,2) 111 = CPU Interrupt Priority Level is 7 (15); user interrupts are disabled 110 = CPU Interrupt Priority Level is 6 (14) 101 = CPU Interrupt Priority Level is 5 (13) 100 = CPU Interrupt Priority Level is 4 (12) 011 = CPU Interrupt Priority Level is 3 (11) 010 = CPU Interrupt Priority Level is 2 (10) 001 = CPU Interrupt Priority Level is 1 (9) 000 = CPU Interrupt Priority Level is 0 (8) bit 4 RA: REPEAT Loop Active bit 1 = REPEAT loop is in progress 0 = REPEAT loop is not in progress bit 3 N: MCU ALU Negative bit 1 = Result was negative 0 = Result was non-negative (zero or positive) bit 2 OV: MCU ALU Overflow bit This bit is used for signed arithmetic (2’s complement). It indicates an overflow of the magnitude that causes the sign bit to change state. 1 = Overflow occurred for signed arithmetic (in this arithmetic operation) 0 = No overflow occurred bit 1 Z: MCU ALU Zero bit 1 = An operation that affects the Z bit has set it at some time in the past 0 = The most recent operation that affects the Z bit has cleared it (i.e., a non-zero result) bit 0 C: MCU ALU Carry/Borrow bit 1 = A carry-out from the Most Significant bit of the result occurred 0 = No carry-out from the Most Significant bit of the result occurred Note 1: 2: 3: The IPL[2:0] bits are concatenated with the IPL[3] bit (CORCON[3]) to form the CPU Interrupt Priority Level. The value in parentheses indicates the IPL, if IPL[3] = 1. User interrupts are disabled when IPL[3] = 1. The IPL[2:0] Status bits are read-only when the NSTDIS bit (INTCON1[15]) = 1. A data write to the SR register can modify the SA and SB bits by either a data write to SA and SB or by clearing the SAB bit. To avoid a possible SA or SB bit write race condition, the SA and SB bits should not be modified using bit operations. DS70005319D-page 266  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-2: CORCON: CORE CONTROL REGISTER R/W-0 U-0 R/W-0 R/W-0 R/W-0 R-0 R-0 R-0 VAR — US1 US0 EDT(1) DL2 DL1 DL0 bit 15 bit 8 R/W-0 R/W-0 R/W-1 R/W-0 R/C-0 R-0 R/W-0 R/W-0 SATA SATB SATDW ACCSAT IPL3(2) SFA RND IF bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 VAR: Variable Exception Processing Latency Control bit 1 = Variable exception processing is enabled 0 = Fixed exception processing is enabled bit 14 Unimplemented: Read as ‘0’ bit 13-12 US[1:0]: DSP Multiply Unsigned/Signed Control bits 11 = Reserved 10 = DSP engine multiplies are mixed sign 01 = DSP engine multiplies are unsigned 00 = DSP engine multiplies are signed bit 11 EDT: Early DO Loop Termination Control bit(1) 1 = Terminates executing DO loop at the end of the current loop iteration 0 = No effect bit 10-8 DL[2:0]: DO Loop Nesting Level Status bits 111 = Seven DO loops are active ... 001 = One DO loop is active 000 = Zero DO loops are active bit 7 SATA: ACCA Saturation Enable bit 1 = Accumulator A saturation is enabled 0 = Accumulator A saturation is disabled bit 6 SATB: ACCB Saturation Enable bit 1 = Accumulator B saturation is enabled 0 = Accumulator B saturation is disabled bit 5 SATDW: Data Space Write from DSP Engine Saturation Enable bit 1 = Data Space write saturation is enabled 0 = Data Space write saturation is disabled bit 4 ACCSAT: Accumulator Saturation Mode Select bit 1 = 9.31 saturation (super saturation) 0 = 1.31 saturation (normal saturation) bit 3 IPL3: CPU Interrupt Priority Level Status bit 3(2) 1 = CPU Interrupt Priority Level is greater than 7 0 = CPU Interrupt Priority Level is 7 or less Note 1: 2: x = Bit is unknown This bit is always read as ‘0’. The IPL3 bit is concatenated with the IPL[2:0] bits (SR[7:5]) to form the CPU Interrupt Priority Level.  2017-2019 Microchip Technology Inc. DS70005319D-page 267 dsPIC33CH128MP508 FAMILY REGISTER 4-2: CORCON: CORE CONTROL REGISTER (CONTINUED) bit 2 SFA: Stack Frame Active Status bit 1 = Stack frame is active; W14 and W15 address 0x0000 to 0xFFFF, regardless of DSRPAG 0 = Stack frame is not active; W14 and W15 address the base Data Space bit 1 RND: Rounding Mode Select bit 1 = Biased (conventional) rounding is enabled 0 = Unbiased (convergent) rounding is enabled bit 0 IF: Integer or Fractional Multiplier Mode Select bit 1 = Integer mode is enabled for DSP multiply 0 = Fractional mode is enabled for DSP multiply Note 1: 2: This bit is always read as ‘0’. The IPL3 bit is concatenated with the IPL[2:0] bits (SR[7:5]) to form the CPU Interrupt Priority Level. REGISTER 4-3: CTXTSTAT: CPU W REGISTER CONTEXT STATUS REGISTER U-0 U-0 U-0 U-0 U-0 — — — — — R-0 R-0 R-0 CCTXI[2:0] bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 — — — — — R-0 R-0 R-0 MCTXI[2:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-11 Unimplemented: Read as ‘0’ bit 10-8 CCTXI[2:0]: Current (W Register) Context Identifier bits 111 = Reserved ... 100 = Alternate Working Register Set 4 is currently in use 011 = Alternate Working Register Set 3 is currently in use 010 = Alternate Working Register Set 2 is currently in use 001 = Alternate Working Register Set 1 is currently in use 000 = Default register set is currently in use bit 7-3 Unimplemented: Read as ‘0’ bit 2-0 MCTXI[2:0]: Manual (W Register) Context Identifier bits 111 = Reserved ... 100 = Alternate Working Register Set 4 was most recently manually selected 011 = Alternate Working Register Set 3 was most recently manually selected 010 = Alternate Working Register Set 2 was most recently manually selected 001 = Alternate Working Register Set 1 was most recently manually selected 000 = Default register set was most recently manually selected DS70005319D-page 268  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 4.1.8 ARITHMETIC LOGIC UNIT (ALU) The dsPIC33CH128MP508S1 family ALU is 16 bits wide and is capable of addition, subtraction, bit shifts and logic operations. Unless otherwise mentioned, arithmetic operations are two’s complement in nature. Depending on the operation, the ALU can affect the values of the Carry (C), Zero (Z), Negative (N), Overflow (OV) and Digit Carry (DC) Status bits in the SR register. The C and DC Status bits operate as Borrow and Digit Borrow bits, respectively, for subtraction operations. The ALU can perform 8-bit or 16-bit operations, depending on the mode of the instruction that is used. Data for the ALU operation can come from the W register array or data memory, depending on the addressing mode of the instruction. Likewise, output data from the ALU can be written to the W register array or a data memory location. Refer to the “16-Bit MCU and DSC Programmer’s Reference Manual” (DS70000157) for information on the SR bits affected by each instruction. The core CPU incorporates hardware support for both multiplication and division. This includes a dedicated hardware multiplier and support hardware for 16-bit divisor division. 4.1.8.1 Multiplier Using the high-speed, 17-bit x 17-bit multiplier, the ALU supports unsigned, signed or mixed-sign operation in several MCU Multiplication modes: • • • • • • • 16-bit x 16-bit signed 16-bit x 16-bit unsigned 16-bit signed x 5-bit (literal) unsigned 16-bit signed x 16-bit unsigned 16-bit unsigned x 5-bit (literal) unsigned 16-bit unsigned x 16-bit signed 8-bit unsigned x 8-bit unsigned 4.1.8.2 Divider 4.1.9 DSP ENGINE The DSP engine consists of a high-speed, 17-bit x 17-bit multiplier, a 40-bit barrel shifter and a 40-bit adder/ subtracter (with two target accumulators, round and saturation logic). The DSP engine can also perform inherent accumulatorto-accumulator operations that require no additional data. These instructions are, ADD, SUB and NEG. The DSP engine has options selected through bits in the CPU Core Control register (CORCON), as listed below: • • • • • • Fractional or integer DSP multiply (IF) Signed, unsigned or mixed-sign DSP multiply (USx) Conventional or convergent rounding (RND) Automatic saturation on/off for ACCA (SATA) Automatic saturation on/off for ACCB (SATB) Automatic saturation on/off for writes to data memory (SATDW) • Accumulator Saturation mode selection (ACCSAT) TABLE 4-2: Instruction DSP INSTRUCTIONS SUMMARY Algebraic Operation ACC Write-Back Yes CLR A=0 ED A = (x – y)2 No 2 EDAC A = A + (x – y) No MAC A = A + (x • y) Yes x2 No MAC A=A+ MOVSAC No change in A Yes MPY A=x•y No MPY A = x2 No MPY.N A=–x•y No MSC A=A–x•y Yes The divide block supports 32-bit/16-bit and 16-bit/16-bit signed and unsigned integer divide operations with the following data sizes: • • • • 32-bit signed/16-bit signed divide 32-bit unsigned/16-bit unsigned divide 16-bit signed/16-bit signed divide 16-bit unsigned/16-bit unsigned divide The quotient for all divide instructions ends up in W0 and the remainder in W1. 16-bit signed and unsigned DIV instructions can specify any W register for both the 16-bit divisor (Wn) and any W register (aligned) pair (W(m + 1):Wm) for the 32-bit dividend. The divide algorithm takes one cycle per bit of divisor, so both 32-bit/16-bit and 16-bit/16-bit instructions take the same number of cycles to execute.  2017-2019 Microchip Technology Inc. DS70005319D-page 269 dsPIC33CH128MP508 FAMILY 4.2 Slave Memory Organization Note: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “dsPIC33/PIC24 Program Memory” (www.microchip.com/DS70000613) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). The dsPIC33CH128MP508S1 family architecture features separate program and data memory spaces, and buses. This architecture also allows the direct access of program memory from the Data Space (DS) during code execution. FIGURE 4-3: 4.2.1 PROGRAM ADDRESS SPACE The program address memory space of the dsPIC33CH128MP508S1 family devices is 4M instructions. The space is addressable by a 24-bit value derived either from the 23-bit PC during program execution, or from table operation or Data Space remapping, as described in Section 4.2.8 “Interfacing Program and Data Memory Spaces”. User application access to the program memory space is restricted to the lower half of the address range (0x000000 to 0x7FFFFF). The exception is the use of TBLRD operations, which use TBLPAG[7] to permit access to calibration data and Device ID sections of the configuration memory space. The PRAM for the Slave dsPIC33CH128MP508S1 devices implements two 12-Kbyte PRAM panels with a total of 24 Kbytes of PRAM available for the Slave device. All variants of the Slave have the same amount of PRAM available, irrespective of the size of the Flash available on the Master Flash program memory, as shown in Figure 4-3. PRAM (PROGRAM MEMORY) FOR SLAVE dsPIC33CH128MP508S1 DEVICES User Memory Space Normal Operation or Single Partition Dual Partition PRAM Organization GOTO Instruction 0x000000 GOTO Instruction Reset Address 0x000002 0x000004 0x0001FE 0x000200 Interrupt Vector Table Interrupt Vector Table User PRAM (24 Kbytes) User Program Memory (12 Kbytes) 0x000200 0x003FFE 0x004000 Unimplemented (Read ‘0’s) GOTO Instruction Unimplemented (Read ‘0’s) Reserved Reset Address 0x000000 0x000002 0x000004 0x0001FE 0x000200 0x3FFFFE 0x400000 0x400002 Reset Address 0x7FFFFE 0x800000 0xF7FFFE 0xF80000 0x400004 Interrupt Vector Table 0x4001FE 0x400200 Configuration Memory Space User Program Memory (12 Kbytes) Calibration Data Unimplemented (Read ‘0’s) 0x7FFFFE Write Latches 0xF80050 0xFA0000 0xFA0002 0xFA0004 Reserved DEVID Reserved Note: 0x401FFE 0x402000 0xFEFFFE 0xFF0000 0xFF0002 0xFF0004 0xFFFFFE Memory areas are not shown to scale. DS70005319D-page 270  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 4.2.1.1 Program Memory Organization 4.2.1.2 The program memory space is organized in wordaddressable blocks. Although it is treated as 24 bits wide, it is more appropriate to think of each address of the program memory as a lower and upper word, with the upper byte of the upper word being unimplemented. The lower word always has an even address, while the upper word has an odd address (Figure 4-4). All dsPIC33CH128MP508S1 family devices reserve the addresses between 0x000000 and 0x000200 for hard-coded program execution vectors. A hardware Reset vector is provided to redirect code execution from the default value of the PC on device Reset to the actual start of code. A GOTO instruction is programmed by the user application at address, 0x000000, of PRAM memory, with the actual address for the start of code at address, 0x000200, of PRAM memory. Program memory addresses are always word-aligned on the lower word, and addresses are incremented, or decremented, by two, during code execution. This arrangement provides compatibility with data memory space addressing and makes data in the program memory space accessible. FIGURE 4-4: msw Address A more detailed discussion of the Interrupt Vector Tables (IVTs) is provided in Table 4-21. PROGRAM MEMORY ORGANIZATION least significant word most significant word 23 0x000001 0x000003 0x000005 0x000007 Interrupt and Trap Vectors 16 8  2017-2019 Microchip Technology Inc. 0 0x000000 0x000002 0x000004 0x000006 00000000 00000000 00000000 00000000 Program Memory ‘Phantom’ Byte (read as ‘0’) PC Address (lsw Address) Instruction Width DS70005319D-page 271 dsPIC33CH128MP508 FAMILY 4.2.2 DATA ADDRESS SPACE (SLAVE) The dsPIC33CH128MP508S1 family CPU has a separate 16-bit wide data memory space. The Data Space is accessed using separate Address Generation Units (AGUs) for read and write operations. The data memory map is shown in Figure 4-5. All Effective Addresses (EAs) in the data memory space are 16 bits wide and point to bytes within the Data Space. This arrangement gives a base Data Space address range of 64 Kbytes or 32K words. The lower half of the data memory space (i.e., when EA[15] = 0) is used for implemented memory addresses, while the upper half (EA[15] = 1) is reserved for the Program Space Visibility (PSV). The dsPIC33CH128MP508S1 family devices implement up to 4 Kbytes of data memory. If an EA points to a location outside of this area, an all-zero word or byte is returned. 4.2.2.1 Data Space Width The data memory space is organized in byteaddressable, 16-bit wide blocks. Data are aligned in data memory and registers as 16-bit words, but all Data Space EAs resolve to bytes. The Least Significant Bytes (LSBs) of each word have even addresses, while the Most Significant Bytes (MSBs) have odd addresses. 4.2.2.2 Data Memory Organization and Alignment To maintain backward compatibility with PIC ® MCU devices and improve Data Space memory usage efficiency, the dsPIC33CH128MP508S1 family instruction set supports both word and byte operations. As a consequence of byte accessibility, all Effective Address calculations are internally scaled to step through wordaligned memory. For example, the core recognizes that Post-Modified Register Indirect Addressing mode [Ws++] results in a value of Ws + 1 for byte operations and Ws + 2 for word operations. A data byte read, reads the complete word that contains the byte, using the LSb of any EA to determine which byte to select. The selected byte is placed onto the LSB of the data path. That is, data memory and registers are organized as two parallel, byte-wide entities with shared (word) address decode, but separate write lines. Data byte writes only write to the corresponding side of the array or register that matches the byte address. DS70005319D-page 272 All word accesses must be aligned to an even address. Misaligned word data fetches are not supported, so care must be taken when mixing byte and word operations, or translating from 8-bit MCU code. If a misaligned read or write is attempted, an address error trap is generated. If the error occurred on a read, the instruction underway is completed. If the error occurred on a write, the instruction is executed but the write does not occur. In either case, a trap is then executed, allowing the system and/or user application to examine the machine state prior to execution of the address Fault. All byte loads into any W register are loaded into the LSB; the MSB is not modified. A Sign-Extend (SE) instruction is provided to allow user applications to translate 8-bit signed data to 16-bit signed values. Alternatively, for 16-bit unsigned data, user applications can clear the MSB of any W register by executing a Zero-Extend (ZE) instruction on the appropriate address. 4.2.2.3 SFR Space The first 4 Kbytes of the Near Data Space, from 0x0000 to 0x0FFF, is primarily occupied by Special Function Registers (SFRs). These are used by the dsPIC33CH128MP508S1 family core and peripheral modules for controlling the operation of the device. SFRs are distributed among the modules that they control and are generally grouped together by module. Much of the SFR space contains unused addresses; these are read as ‘0’. Note: 4.2.2.4 The actual set of peripheral features and interrupts varies by the device. Refer to the corresponding device tables and pinout diagrams for device-specific information. Near Data Space The 8-Kbyte area, between 0x0000 and 0x1FFF, is referred to as the Near Data Space. Locations in this space are directly addressable through a 13-bit absolute address field within all memory direct instructions. Additionally, the whole Data Space is addressable using MOV instructions, which support Memory Direct Addressing mode with a 16-bit address field, or by using Indirect Addressing mode using a Working register as an Address Pointer.  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 4-5: DATA MEMORY MAP FOR SLAVE dsPIC33CH128MP508S1 DEVICES MSB Address MSB 4-Kbyte SFR Space LSB Address 16 Bits LSB 0x0001 0x0000 SFR Space 0x0FFE 0x1000 0x0FFF 0x1001 X Data RAM (X) (2K) 4-Kbyte SRAM Space 0x1800 0x1802 0x17FE 0x1801 8-Kbyte Near Data Space Y Data RAM (Y) (2K) 0x1FFF 0x2001 0x1FFE 0x2000 0x8001 0x8000 X Data Unimplemented (X) 0xFFFF Note: Optionally Mapped into Program Memory 0xFFFE Memory areas are not shown to scale.  2017-2019 Microchip Technology Inc. DS70005319D-page 273 dsPIC33CH128MP508 FAMILY 4.2.2.5 X and Y Data Spaces The dsPIC33CH128MP508S1 family core has two Data Spaces, X and Y. These Data Spaces can be considered either separate (for some DSP instructions) or as one unified linear address range (for MCU instructions). The Data Spaces are accessed using two Address Generation Units (AGUs) and separate data paths. This feature allows certain instructions to concurrently fetch two words from RAM, thereby enabling efficient execution of DSP algorithms, such as Finite Impulse Response (FIR) filtering and Fast Fourier Transform (FFT). The X Data Space is used by all instructions and supports all addressing modes. X Data Space has separate read and write data buses. The X read data bus is the read data path for all instructions that view Data Space as combined X and Y address space. It is also the X data prefetch path for the dual operand DSP instructions (MAC class). The Y Data Space is used in concert with the X Data Space by the MAC class of instructions (CLR, ED, EDAC, MAC, MOVSAC, MPY, MPY.N and MSC) to provide two concurrent data read paths. 4.2.3 MEMORY RESOURCES Many useful resources are provided on the main product page of the Microchip website for the devices listed in this data sheet. This product page contains the latest updates and additional information. 4.2.3.1 Key Resources • “dsPIC33/PIC24 Program Memory” (www.microchip.com/DS70000613) in the “dsPIC33/PIC24 Family Reference Manual” • Code Samples • Application Notes • Software Libraries • Webinars • All Related “dsPIC33/PIC24 Family Reference Manual” Sections • Development Tools Both the X and Y Data Spaces support Modulo Addressing mode for all instructions, subject to addressing mode restrictions. Bit-Reversed Addressing mode is only supported for writes to X Data Space. All data memory writes, including in DSP instructions, view Data Space as combined X and Y address space. The boundary between the X and Y Data Spaces is device-dependent and is not user-programmable. DS70005319D-page 274  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 4.2.4 SFR MAPS The following tables show dsPIC33CH128MP508 family Slave SFR names, addresses and Reset values. These tables contain all registers applicable to the TABLE 4-3: Register dsPIC33CH128MP508S1 family. Not all registers are present on all device variants. Refer to Table 1 and Table 2 for peripheral availability. Table 4-25 details port availability for the different package options. SLAVE SFR BLOCK 000h Address All Resets Register Address Address All Resets DSRPAG 032 ------0000000001 WREG0 000 0000000000000000 DSWPAG 034 -----00000000001 CLC1GLSL 0C8 0000000000000000 CLC1GLSH 0CA WREG1 002 0000000000000000 RCOUNT 036 xxxxxxxxxxxxxxxx 0000000000000000 CLC2CONL 0CC WREG2 004 0000000000000000 DCOUNT 038 0-0-00--000--000 xxxxxxxxxxxxxxxx CLC2CONH 0CE WREG3 006 0000000000000000 DOSTART ------------0000 03A 1111111111111111 CLC2SELL 0D0 WREG4 008 0000000000000000 -000-000-000-000 DOSTARTL 03A 1111111111111110 CLC2SELH 0D2 WREG5 00A 0000000000000000 ---------------- DOSTARTH 03C 0000000011111111 CLC2GLSL 0D4 0000000000000000 WREG6 00C WREG7 00E 0000000000000000 DOENDL 03E xxxxxxxxxxxxxxx0 CLC2GLSH 0D6 0000000000000000 0000000000000000 DOENDH 040 ---------xxxxxxx CLC3CONL 0D8 WREG8 0-0-00--000--000 010 0000000000000000 SR 042 0000000000000000 CLC3CONH 0DA ------------0000 WREG9 012 0000000000000000 CORCON 044 x-xx000000100000 CLC3SELL 0DC -000-000-000-000 WREG10 014 0000000000000000 MODCON 046 00--000000000000 CLC3GLSL 0E0 0000000000000000 0000000000000000 Core All Resets Register WREG11 016 0000000000000000 XMODSRT 048 xxxxxxxxxxxxxxx0 CLC3GLSH 0E2 WREG12 018 0000000000000000 XMODEND 04A xxxxxxxxxxxxxxx1 CLC4CONL 0E4 0-0-00--000--000 WREG13 01A 0000000000000000 YMODSRT 04C xxxxxxxxxxxxxxx0 CLC4CONH 0E6 ------------0000 WREG14 01C 0000000000000000 YMODEND 04E xxxxxxxxxxxxxxx1 CLC4SELL 0E8 -000-000-000-000 WREG15 01E 0000100000000000 XBREV 050 0xxxxxxxxxxxxxxx CLC4GLSL 0EC 0000000000000000 SPLIM 020 xxxxxxxxxxxxxxxx DISICNT 052 xxxxxxxxxxxxxx00 CLC4GLSH 0EE 0000000000000000 ACCAL 022 xxxxxxxxxxxxxxxx TBLPAG 054 --------00000000 ECCCONL 0F0 ---------------0 ACCAH 024 xxxxxxxxxxxxxxxx YPAG 056 --------00000001 ECCCONH 0F2 0000000000000000 ACCAU 026 xxxxxxxxxxxxxxxx MSTRPR 058 ----------0----- ECCADDRL 0F4 0000000000000000 ACCBL 028 xxxxxxxxxxxxxxxx CTXTSTAT 05A 0000000000000000 ECCADDRH 0F6 0000000000000000 ACCBH 02A xxxxxxxxxxxxxxxx CLC ECCSTATL 0F8 0000000000000000 ACCBU 02C xxxxxxxxxxxxxxxx CLC1CONL 0C0 0-0-00--000--000 ECCSTATH 0FA ------0000000000 PCL 02E 0000000000000000 CLC1CONH 0C2 ------------0000 PCH 030 --------00000000 CLC1SELL 0C4 -000-000-000-000 Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively.  2017-2019 Microchip Technology Inc. DS70005319D-page 275 dsPIC33CH128MP508 FAMILY TABLE 4-4: Register SLAVE SFR BLOCK 100h Address All Resets Register Address All Resets Register Address All Resets INT1TMRL 15C 0000000000000000 SI1MBX2D 1DE 0000000000000000 T1CON 100 0-0000000-00-00- INT1TMRH 15E 0000000000000000 SI1MBX3D 1E0 0000000000000000 TMR1 104 0000000000000000 INT1HLDL 160 0000000000000000 SI1MBX4D 1E2 0000000000000000 PR1 108 0000000000000000 INT1HLDH 162 0000000000000000 SI1MBX5D 1E4 0000000000000000 INDX1CNTL 164 0000000000000000 SI1MBX6D 1E6 0000000000000000 Timers QEI QEI1CON 140 0000000000000000 INDX1CNTH 166 0000000000000000 SI1MBX7D 1E8 0000000000000000 QEI1IOCL 144 000000000000xxxx INDX1HLDL 168 0000000000000000 SI1MBX8D 1EA 0000000000000000 QEI1IOCH 146 ---------------0 INDX1HLDH 16A 0000000000000000 SI1MBX9D 1EC 0000000000000000 QEI1STAT 148 --00000000000000 QEI1GECL 16C 0000000000000000 SI1MBX10D 1EE 0000000000000000 POS1CNTL 14C 0000000000000000 QEI1GECH 16E 0000000000000000 SI1MBX11D 1F0 0000000000000000 POS1CNTH 14E 0000000000000000 QEI1LECL 170 0000000000000000 SI1MBX12D 1F2 0000000000000000 POS1HLDL 150 0000000000000000 QEI1LECH 172 0000000000000000 SI1MBX13D 1F4 0000000000000000 POS1HLDH 152 0000000000000000 SI1CON 1D2 0---xx0000000000 SI1MBX14D 1F6 0000000000000000 VEL1CNTL 154 0000000000000000 SI1STAT 1D4 0000000000000000 SI1MBX15D 1F8 0000000000000000 VEL1CNTH 156 0000000000000000 SI1MBXS 1D8 --------00000000 SI1FIFOCS 1FA 0---00000---0000 VEL1HLDL 158 0000000000000000 SI1MBX0D 1DA 0000000000000000 SWMRFDATA 1FC 0000000000000000 VEL1HLDH 15A 0000000000000000 SI1MBX1D 1DC 0000000000000000 SRMWFDATA 1FE 0000000000000000 Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively. TABLE 4-5: Register SLAVE SFR BLOCK 200h Address All Resets Register Address U1BRGH 242 200 0-01000000000000 U1RXREG 244 2 I C I2C1CONL All Resets Register Address All Resets ------------0000 SPI1CON2L 2B0 -----------00000 --------xxxxxxxx SPI1CON2H 2B2 ------------------00--0001-1-00 I2C1CONH 202 ---------0000000 U1TXREG 248 -------xxxxxxxxx SPI1STATL 2B4 I2C1STAT 204 000--00000000000 U1P1 24C -------000000000 SPI1STATH 2B6 --000000--000000 I2C1ADD 208 ------0000000000 U1P2 24E -------000000000 SPI1BUFL 2B8 0000000000000000 I2C1MSK 20C ------0000000000 U1P3 250 0000000000000000 SPI1BUFH 2BA 0000000000000000 I2C1BRG 210 0000000000000000 U1P3H 252 --------00000000 SPI1BRGL 2BC ---xxxxxxxxxxxxx I2C1TRN 214 --------11111111 U1TXCHK 254 --------00000000 SPI1BRGH 2BE ---------------- I2C1RCV 218 --------00000000 UART U1RXCHK 256 --------00000000 SPI1IMSKL 2C0 ---00--0000-0-00 U1SCCON 258 ----------00000- SPI1IMSKH 2C2 0-0000000-000000 U1MODE 238 0-000-0000000000 U1SCINT 25A --00-000--00-000 SPI1URDTL 2C4 0000000000000000 U1MODEH 23A 00---00000000000 U1INT 25C --------00---0-- SPI1URDTH 2C6 0000000000000000 U1STA 23C 0000000010000000 U1STAH 23E -000-00000101110 SPI1CON1L 2AC 0-00000000000000 U1BRG 240 0000000000000000 SPI1CON1H 2AE 0000000000000000 SPI Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively. DS70005319D-page 276  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 4-6: Register SLAVE SFR BLOCK 300h Address All Resets Register High-Speed PWM Address All Resets Register Address All Resets 0000-00000000000 PG1TRIGB 356 0000000000000000 PG3FFPCIH 3AE PCLKCON 300 00-----0--00--00 PG1TRIGC 358 0000000000000000 PG3SPCIL 3B0 0000000000000000 FSCL 302 0000000000000000 PG1DTL 35A --00000000000000 PG3SPCIH 3B2 0000-00000000000 FSMINPER 304 0000000000000000 PG1DTH 35C --00000000000000 PG3LEBL 3B4 0000000000000000 MPHASE 306 0000000000000000 PG1CAP 35E 0000000000000000 PG3LEBH 3B6 -----000----0000 MDC 308 0000000000000000 PG2CONL 360 0-00000000000000 PG3PHASE 3B8 0000000000000000 MPER 30A 0000000000000000 PG2CONH 362 000-000000--0000 PG3DC 3BA 0000000000000000 LFSR 30C 0000000000000000 PG2STAT 364 0000000000000000 PG3DCA 3BC --------00000000 CMBTRIGL 30E --------00000000 PG2IOCONL 366 0000000000000000 PG3PER 3BE 0000000000000000 CMBTRIGH 310 --------00000000 PG2IOCONH 368 -000---0--000000 PG3TRIGA 3C0 0000000000000000 LOGCONA 312 000000000000-000 PG2EVTL 36A 00000000---00000 PG3TRIGB 3C2 0000000000000000 LOGCONB 314 000000000000-000 PG2EVTH 36C 0000--0000000000 PG3TRIGC 3C4 0000000000000000 LOGCONC 316 000000000000-000 PG2FPCIL 36E 0000000000000000 PG3DTL 3C6 --00000000000000 LOGCOND 318 000000000000-000 PG2FPCIH 370 0000-00000000000 PG3DTH 3C8 --00000000000000 LOGCONE 31A 000000000000-000 PG2CLPCIL 372 0000000000000000 PG3CAP 3CA 0000000000000000 LOGCONF 31C 000000000000-000 PG2CLPCIH 374 0000-00000000000 PG4CONL 3CC 0-00000000000000 PWMEVTA 31E 0000----0000-000 PG2FFPCIL 376 0000000000000000 PG4CONH 3CE 000-000000--0000 PWMEVTB 320 0000----0000-000 PG2FFPCIH 378 0000-00000000000 PG4STAT 3D0 0000000000000000 PWMEVTC 322 0000----0000-000 PG2SPCIL 37A 0000000000000000 PG4IOCONL 3D2 0000000000000000 PWMEVTD 324 0000----0000-000 PG2SPCIH 37C 0000-00000000000 PG4IOCONH 3D4 -000---0--000000 PWMEVTE 326 0000----0000-000 PG2LEBL 37E 0000000000000000 PG4EVTL 3D6 00000000---00000 PWMEVTF 328 0000----0000-000 PG2LEBH 380 -----000----0000 PG4EVTH 3D8 0000--0000000000 PG1CONL 32A 0-00000000000000 PG2PHASE 382 0000000000000000 PG4FPCIL 3DA 0000000000000000 PG1CONH 32C 000-000000--0000 PG2DC 384 0000000000000000 PG4FPCIH 3DC 0000-00000000000 PG1STAT 32E 0000000000000000 PG2DCA 386 --------00000000 PG4CLPCIL 3DE 0000000000000000 PG1IOCONL 330 0000000000000000 PG2PER 388 0000000000000000 PG4CLPCIH 3E0 0000-00000000000 PG1IOCONH 332 -000---0--000000 PG2TRIGA 38A 0000000000000000 PG4FFPCIL 3E2 0000000000000000 0000-00000000000 PG1EVTL 334 00000000---00000 PG2TRIGB 38C 0000000000000000 PG4FFPCIH 3E4 PG1EVTH 336 0000--0000000000 PG2TRIGC 38E 0000000000000000 PG4SPCIL 3E6 0000000000000000 PG1FPCIL 338 0000000000000000 PG2DTL 390 --00000000000000 PG4SPCIH 3E8 0000-00000000000 PG1FPCIH 33A 0000-00000000000 PG2DTH 392 --00000000000000 PG4LEBL 3EA 0000000000000000 PG1CLPCIL 33C 0000000000000000 PG2CAP 394 0000000000000000 PG4LEBH 3EC -----000----0000 PG1CLPCIH 33E 0000-00000000000 PG3CONL 396 0-00000000000000 PG4PHASE 3EE 0000000000000000 PG1FFPCIL 340 0000000000000000 PG3CONH 398 000-000000--0000 PG4DC 3F0 0000000000000000 PG1FFPCIH 342 0000-00000000000 PG3STAT 39A 0000000000000000 PG4DCA 3F2 --------00000000 PG1SPCIL 344 0000000000000000 PG3IOCONL 39C 0000000000000000 PG4PER 3F4 0000000000000000 PG1SPCIH 346 0000-00000000000 PG3IOCONH 39E -000---0--000000 PG4TRIGA 3F6 0000000000000000 PG1LEBL 348 0000000000000000 PG3EVTL 3A0 00000000---00000 PG4TRIGB 3F8 0000000000000000 PG1LEBH 34A -----000----0000 PG3EVTH 3A2 0000--0000000000 PG4TRIGC 3FA 0000000000000000 PG1PHASE 34C 0000000000000000 PG3FPCIL 3A4 0000000000000000 PG4DTL 3FC --00000000000000 PG1DC 34E 0000000000000000 PG3FPCIH 3A6 0000-00000000000 PG4DTH 3FE --00000000000000 PG1DCA 350 --------00000000 PG3CLPCIL 3A8 0000000000000000 PG4CAP 400 0000000000000000 PG1PER 352 0000000000000000 PG3CLPCIH 3AA 0000-00000000000 PG1TRIGA 354 0000000000000000 PG3FFPCIL 3AC 0000000000000000 Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively.  2017-2019 Microchip Technology Inc. DS70005319D-page 277 dsPIC33CH128MP508 FAMILY TABLE 4-7: Register SLAVE SFR BLOCK 400h Address All Resets High-Speed PWM (Continued) Register Address All Resets Register Address All Resets 0000000000000000 PG6CLPCIL 44A 0000000000000000 PG7DC 492 PG5CONL 402 0-00000000000000 PG6CLPCIH 44C 0000-00000000000 PG7DCA 494 --------00000000 PG5CONH 404 000-000000--0000 PG6FFPCIL 44E 0000000000000000 PG7PER 496 0000000000000000 PG5STAT 406 0000000000000000 PG6FFPCIH 450 0000-00000000000 PG7TRIGA 498 0000000000000000 PG5IOCONL 408 0000000000000000 PG6SPCIL 452 0000000000000000 PG7TRIGB 49A 0000000000000000 PG5IOCONH 40A -000---0--000000 PG6SPCIH 454 0000-00000000000 PG7TRIGC 49C 0000000000000000 PG5EVTL 40C 00000000---00000 PG6LEBL 456 0000000000000000 PG7DTL 49E --00000000000000 PG5EVTH 40E 0000--0000000000 PG6LEBH 458 -----000----0000 PG7DTH 4A0 --00000000000000 PG5FPCIL 410 0000000000000000 PG6PHASE 45A 0000000000000000 PG7CAP 4A2 0000000000000000 PG5FPCIH 412 0000-00000000000 PG6DC 45C 0000000000000000 PG8CONL 4A4 0-00000000000000 PG5CLPCIL 414 0000000000000000 PG6DCA 45E --------00000000 PG8CONH 4A6 000-000000--0000 PG5CLPCIH 416 0000-00000000000 PG6PER 460 0000000000000000 PG8STAT 4A8 0000000000000000 PG5FFPCIL 418 0000000000000000 PG6TRIGA 462 0000000000000000 PG8IOCONL 4AA 0000000000000000 PG5FFPCIH 41A 0000-00000000000 PG6TRIGB 464 0000000000000000 PG8IOCONH 4AC -000---0--000000 PG5SPCIL 41C 0000000000000000 PG6TRIGC 466 0000000000000000 PG8EVTL 4AE 00000000---00000 PG5SPCIH 41E 0000-00000000000 PG6DTL 468 --00000000000000 PG8EVTH 4B0 0000--0000000000 PG5LEBL 420 0000000000000000 PG6DTH 46A --00000000000000 PG8FPCIL 4B2 0000000000000000 PG5LEBH 422 -----000----0000 PG6CAP 46C 0000000000000000 PG8FPCIH 4B4 0000-00000000000 PG5PHASE 424 0000000000000000 PG7CONL 46E 0-00000000000000 PG8CLPCIL 4B6 0000000000000000 PG5DC 426 0000000000000000 PG7CONH 470 000-000000--0000 PG8CLPCIH 4B8 0000-00000000000 PG5DCA 428 --------00000000 PG7STAT 472 0000000000000000 PG8FFPCIL 4BA 0000000000000000 PG5PER 42A 0000000000000000 PG7IOCONL 474 0000000000000000 PG8FFPCIH 4BC 0000-00000000000 PG5TRIGA 42C 0000000000000000 PG7IOCONH 476 -000---0--000000 PG8SPCIL 4BE 0000000000000000 PG5TRIGB 42E 0000000000000000 PG7EVTL 478 00000000---00000 PG8SPCIH 4C0 0000-00000000000 PG5TRIGC 430 0000000000000000 PG7EVTH 47A 0000--0000000000 PG8LEBL 4C2 0000000000000000 PG5DTL 432 --00000000000000 PG7FPCIL 47C 0000000000000000 PG8LEBH 4C4 -----000----0000 PG5DTH 434 --00000000000000 PG7FPCIH 47E 0000-00000000000 PG8PHASE 4C6 0000000000000000 PG5CAP 436 0000000000000000 PG7CLPCIL 480 0000000000000000 PG8DC 4C8 0000000000000000 PG6CONL 438 0-00000000000000 PG7CLPCIH 482 0000-00000000000 PG8DCA 4CA --------00000000 PG6CONH 43A 000-000000--0000 PG7FFPCIL 484 0000000000000000 PG8PER 4CC 0000000000000000 PG6STAT 43C 0000000000000000 PG7FFPCIH 486 0000-00000000000 PG8TRIGA 4CE 0000000000000000 PG6IOCONL 43E 0000000000000000 PG7SPCIL 488 0000000000000000 PG8TRIGB 4D0 0000000000000000 PG6IOCONH 440 -000---0--000000 PG7SPCIH 48A 0000-00000000000 PG8TRIGC 4D2 0000000000000000 PG6EVTL 442 00000000---00000 PG7LEBL 48C 0000000000000000 PG8DTL 4D4 --00000000000000 PG6EVTH 444 0000--0000000000 PG7LEBH 48E -----000----0000 PG8DTH 4D6 --00000000000000 PG6FPCIL 446 0000000000000000 PG7PHASE 490 0000000000000000 PG8CAP 4D8 0000000000000000 PG6FPCIH 448 0000-00000000000 Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively. DS70005319D-page 278  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 4-8: Register SLAVE SFR BLOCK 800h Address All Resets Register IPC2 844 -100-100-100-100 IPC34 884 -100-100-100-100 800 0000000000-00000 IPC3 846 -100-100-100-100 IPC35 886 ---------100-100 Interrupts IFS0 Address All Resets Register Address All Resets IFS1 802 0000000000000000 IPC4 848 -100-100-100-100 IPC35 886 ---------100-100 IFS2 804 00000-00-00000-- IPC5 84A -100-100-100-100 IPC36 888 -----100-------- IFS3 806 000--------00000 IPC6 84C -100-100-100-100 IPC42 894 -100-100-100-100 IFS4 808 --000----0000-00 IPC8 850 -100-100-------- IPC43 896 -100-100-100-100 IFS5 80A 000000000000000- IPC9 852 -----100-100-100 IPC44 898 -100-100-100-100 IFS6 80C 0000000000000000 IPC10 854 -100-----100-100 IPC45 89A -------------100 IFS7 80E 0000000000000--- IPC12 858 -100-100-100-100 IPC47 89E -----100-100---- IFS8 810 --0000000000000- IPC15 85E -100-100-100---- INTCON1 8C0 000000000000000- IFS9 812 --0---00-00--0-- IPC16 860 -100-----100-100 INTCON2 8C2 000----0----0000 IFS10 814 00000000-------- IPC17 862 -----100-100-100 INTCON3 8C4 -------0---0---0 IFS11 816 -00--------00000 IPC18 864 -100------------ INTCON4 8C6 --------------00 IEC0 820 0000000000-00000 IPC19 866 ---------100-100 INTTREG 8C8 000-000000000000 IEC1 822 0000000000000000 IPC20 868 -100-100-100---- Flash IEC2 824 00000-00-00000-- IPC21 86A -100-100-100-100 NVMCON 8D0 0000--00----0000 IEC3 826 000--------00000 IPC22 86C -100-100-100-100 NVMADR 8D2 0000000000000000 IEC4 828 --000----0000-00 IPC23 86E -100-100-100-100 NVMADRU 8D4 --------00000000 IEC5 82A 000000000000000- IPC24 870 -100-100-100-100 NVMKEY 8D6 --------00000000 IEC6 82C 0000000000000000 IPC25 872 -100-100-100-100 NVMSRCADRL 8D8 0000000000000000 IEC7 82E 0000000000000--- IPC26 874 -100-100-100-100 NVMSRCADRH 8DA --------00000000 IEC8 830 --0000000000000- IPC27 876 -100-100-100-100 PGA1CON 8E0 00000000---0-010 IEC8 830 --0000000000000- IPC28 878 -100------------ PGA1CAL 8E2 --------00000000 IEC9 832 --0---00-00--0-- IPC29 87A -100-100-100-100 PGA2CON 8E4 00000000---0-010 IEC10 834 00000000------00 IPC30 87C -100-100-100-100 PGA2CAL 8E6 --------00000000 IEC11 836 -00--------00000 IPC31 87E -100-100-100-100 PGA3CON 8E8 00000000---0-010 IPC0 840 -100-100-100-100 IPC32 880 -100-100-100---- PGA3CAL 8EA --------00000000 IPC1 842 -100-100-----100 IPC33 882 -100-100-100-100 Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively.  2017-2019 Microchip Technology Inc. DS70005319D-page 279 dsPIC33CH128MP508 FAMILY TABLE 4-9: Register SLAVE SFR BLOCK 900h Address All Resets 950 0-00000000000000 CCP CCP1CON1L Register Address All Resets Register Address CCP2CON3H CCP2STATL All Resets 97E 0000------0-00-- CCP3PRH 9AE 1111111111111111 980 -----0--00xx0000 CCP3RAL 9B0 0000000000000000 CCP1CON1H 952 00--000000000000 CCP2TMRL 984 0000000000000000 CCP3RBL 9B4 0000000000000000 CCP1CON2L 954 00-0----00000000 CCP2TMRH 986 0000000000000000 CCP3BUFL 9B8 0000000000000000 CCP1CON2H 956 0------100-00000 CCP2PRL 988 1111111111111111 CCP3BUFH 9BA 0000000000000000 CCP1CON3H 95A 0000------0-00-- CCP2PRH 98A 1111111111111111 CCP4CON1L 9BC 0-00000000000000 CCP1STATL 95C -----0--00xx0000 CCP2RAL 98C 0000000000000000 CCP4CON1H 9BE 00--000000000000 CCP1TMRL 960 0000000000000000 CCP2RBL 990 0000000000000000 CCP4CON2L 9C0 00-0----00000000 CCP1TMRH 962 0000000000000000 CCP2BUFL 994 0000000000000000 CCP4CON2H 9C2 0------100-00000 CCP1PRL 964 1111111111111111 CCP2BUFH 996 0000000000000000 CCP4CON3H 9C6 0000------0-00-- CCP1PRH 966 1111111111111111 CCP3CON1L 998 0-00000000000000 CCP4STATL 9C8 -----0--00xx0000 CCP1RAL 968 0000000000000000 CCP3CON1H 99A 00--000000000000 CCP4TMRL 9CC 0000000000000000 CCP1RBL 96C 0000000000000000 CCP3CON2L 99C 00-0----00000000 CCP4TMRH 9CE 0000000000000000 CCP1BUFL 970 0000000000000000 CCP3CON2H 99E 0------100-00000 CCP4PRL 9D0 1111111111111111 CCP1BUFH 972 0000000000000000 CCP3CON3H 9A2 0000------0-00-- CCP4PRH 9D2 1111111111111111 CCP2CON1L 974 0-00000000000000 CCP3STATL 9A4 -----0--00xx0000 CCP4RAL 9D4 0000000000000000 CCP2CON1H 976 00--000000000000 CCP3TMRL 9A8 0000000000000000 CCP4RBL 9D8 0000000000000000 CCP2CON2L 978 00-0----00000000 CCP3TMRH 9AA 0000000000000000 CCP4BUFL 9DC 0000000000000000 CCP2CON2H 97A 0------100-00000 CCP3PRL 9AC 1111111111111111 CCP4BUFH 9DE 0000000000000000 Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively. TABLE 4-10: Register SLAVE SFR BLOCK A00h Address All Resets Register DMACH0 AC4 DMACON ABC 0-0------------0 DMAINT0 AC6 DMABUF ABE 0000000000000000 DMASRC0 AC8 0000000000000000 DMASRC1 AD2 0000000000000000 DMAL AC0 0001000000000000 DMADST0 ACA 0000000000000000 DMADST1 AD4 0000000000000000 DMAH AC2 0001000000000000 DMACNT0 ACC 0000000000000001 DMACNT1 AD6 0000000000000001 DMA Address All Resets Register Address All Resets ---0-00000000000 DMACH1 ACE ---0-00000000000 0000000000000--0 DMAINT1 AD0 0000000000000--0 Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively. DS70005319D-page 280  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 4-11: Register SLAVE SFR BLOCK B00h Address All Resets Register Address All Resets Address All Resets ADCON1L B00 000-00000----000 ADCMP1ENH B42 -----------00000 ADCMP1LO B44 0000000000000000 ADTRIG2L B88 0000000000000000 ADTRIG2H B8A ADCON1H B02 --------011----- ADCMP1HI B46 0000000000000000 0000000000000000 ADTRIG3L B8C ADCON2L B04 00-0000000000000 ADCMP2ENL B48 0000000000000000 0000000000000000 ADTRIG3H B8E ADCON2H B06 00-0000000000000 ADCMP2ENH 0000000000000000 B4A -----------00000 ADTRIG4L B90 ADCON3L B08 00000x0000000000 0000000000000000 ADCMP2LO B4C 0000000000000000 ADTRIG4H B92 ADCON3H B0A 000000000------- 0000000000000000 ADCMP2HI B4E 0000000000000000 ADTRIG5L B94 ADCON4L B0C 000-----00000000 0-----000-----xx ADCMP3ENL B50 0000000000000000 ADCMP0CON BA0 ADCON4H 0000000000000000 B0E 00----------0000 ADCMP3ENH B52 -----------00000 ADCMP1CON BA4 ADMOD0L 0000000000000000 B10 -0-0-0-0-0-00000 ADCMP3LO B54 0000000000000000 ADCMP2CON BA8 0000000000000000 ADC Register ADMOD0H B12 -0-0-0-0-0-0-0-0 ADCMP3HI B56 0000000000000000 ADCMP3CON BAC 0000000000000000 ADMOD1L B14 -------0-0-0-0-0 ADFL0DAT B68 0000000000000000 ADLVLTRGL BD0 0000000000000000 ADIEL B20 xxxxxxxxxxxxxxxx ADFL0CON B6A 0xx0000000000000 ADLVLTRGH BD2 -----------xxxxx ADIEH B22 -----------xxxxx ADFL1DAT B6C 0000000000000000 ADCORE0L BD4 0000000000000000 ADCSS1L B28 0000000000000000 ADFL1CON B6E 0xx0000000000000 ADCORE0H BD6 0000001100000000 ADCSS1H B2A -------------000 ADFL2DAT B70 0000000000000000 ADCORE1L BD8 0000000000000000 ADSTATL B30 0000000000000000 ADFL2CON B72 0xx0000000000000 ADCORE1H BDA 0000001100000000 ADSTATH B32 -----------00000 ADFL3DAT B74 0000000000000000 ADEIEL BF0 xxxxxxxxxxxxxxxx -----------xxxxx ADCMP0ENL B38 0000000000000000 ADFL3CON B76 0xx0000000000000 ADEIEH BF2 ADCMP0ENH B3A -----------00000 ADTRIG0L B80 0000000000000000 ADEISTATL BF8 xxxxxxxxxxxxxxxx ADCMP0LO B3C 0000000000000000 ADTRIG0H B82 0000000000000000 ADEISTATH BFA -----------xxxxx ADCMP0HI B3E 0000000000000000 ADTRIG1L B84 0000000000000000 ADCMP1ENL B40 0000000000000000 ADTRIG1H B86 0000000000000000 Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively. TABLE 4-12: Register SLAVE SFR BLOCK C00h Address All Resets Register ADCBUF12 C24 0-------0------- ADCBUF13 C26 ADC (Continued) ADCON5L C00 Address All Resets Register Address All Resets 0000000000000000 SLP1CONL C90 0000000000000000 0000000000000000 SLP1CONH C92 0---000--------- ADCON5H C02 0---xxxx0------- ADCBUF14 C28 0000000000000000 SLP1DAT C94 0000000000000000 ADCAL0L C04 0000000000000000 ADCBUF15 C2A 0000000000000000 DAC2CONL C98 000--000x0000000 ADCAL1H C0A 00000-00-000---- ADCBUF16 C2C 0000000000000000 DAC2CONH C9A ------0000000000 ADCBUF0 C0C 0000000000000000 ADCBUF17 C2E 0000000000000000 DAC2DATL C9C 0000000000000000 ADCBUF1 C0E 0000000000000000 ADCBUF18 C30 0000000000000000 DAC2DATH C9E 0000000000000000 ADCBUF2 C10 0000000000000000 ADCBUF19 C32 0000000000000000 SLP2CONL CA0 0000000000000000 C80 000-----0000-000 ADCBUF3 C12 0000000000000000 DAC ADCBUF4 C14 0000000000000000 DACCTRL1L SLP2CONH CA2 0---000--------- SLP2DAT CA4 0000000000000000 ADCBUF5 C16 0000000000000000 DACCTRL2L C84 ------0001010101 DAC3CONL CA8 000--000x0000000 ADCBUF6 C18 0000000000000000 DACCTRL2H C86 ------0010001010 DAC3CONH CAA ------0000000000 ADCBUF7 C1A 0000000000000000 DAC1CONL C88 000--000x0000000 DAC3DATL CAC 0000000000000000 ADCBUF8 C1C 0000000000000000 ADCBUF12 C24 0000000000000000 DAC3DATH CAE 0000000000000000 ADCBUF9 C1E 0000000000000000 DAC1CONH C8A ------0000000000 SLP3CONL CB0 0000000000000000 ADCBUF10 C20 0000000000000000 DAC1DATL C8C 0000000000000000 SLP3CONH CB2 0---000--------- ADCBUF11 C22 0000000000000000 DAC1DATH C8E 0000000000000000 SLP3DAT CB4 0000000000000000 Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively.  2017-2019 Microchip Technology Inc. DS70005319D-page 281 dsPIC33CH128MP508 FAMILY TABLE 4-13: Register SLAVE SFR BLOCK D00h Address All Resets Address All Resets Register Address All Resets RPCON D00 ----0----------- RPINR23 D32 1111111111111111 RPOR8 D90 --000000--000000 RPINR37 D4E 11111111-------- RPOR9 D92 RPINR0 D04 --000000--000000 11111111-------- RPINR38 D50 --------11111111 RPOR10 D94 RPINR1 --000000--000000 D06 1111111111111111 RPINR42 D58 1111111111111111 RPOR11 D96 --000000--000000 RPINR2 D08 11111111-------- RPINR43 D5A 1111111111111111 RPOR12 D98 --000000--000000 RPINR3 D0A 1111111111111111 RPINR44 D5C 1111111111111111 RPOR13 D9A --000000--000000 RPINR4 D0C 1111111111111111 RPINR45 D5E 1111111111111111 RPOR14 D9C --000000--000000 RPINR5 D0E 1111111111111111 RPINR46 D60 1111111111111111 RPOR15 D9E --000000--000000 RPINR6 D10 1111111111111111 RPINR47 D62 1111111111111111 RPOR16 DA0 --000000--000000 RPINR11 D1A 1111111111111111 RPOR0 D80 --000000--000000 RPOR17 DA2 --000000--000000 RPINR12 D1C 1111111111111111 RPOR1 D82 --000000--000000 RPOR18 DA4 --000000--000000 RPINR13 D1E 1111111111111111 RPOR2 D84 --000000--000000 RPOR19 DA6 --000000--000000 RPINR14 D20 1111111111111111 RPOR3 D86 --000000--000000 RPOR20 DA8 --000000--000000 RPINR15 D22 1111111111111111 RPOR4 D88 --000000--000000 RPOR21 DAA --000000--000000 RPINR18 D28 1111111111111111 RPOR5 D8A --000000--000000 RPOR22 DAC --000000--000000 RPINR20 D2C 1111111111111111 RPOR6 D8C --000000--000000 RPINR21 D2E 1111111111111111 RPOR7 D8E --000000--000000 I/O Ports Register Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively. DS70005319D-page 282  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 4-14: Register SLAVE SFR BLOCK E00h Address All Resets Register Address All Resets Register Address All Resets I/O Ports (Continued) CNEN0B E2C 0000000000000000 CNPUD E5E 0000000000000000 ANSELA E00 -----------1111- CNSTATB E2E 0000000000000000 CNPDD E60 0000000000000000 TRISA E02 -----------11111 CNEN1B E30 0000000000000000 CNCOND E62 0---0----------- PORTA E04 -----------xxxxx CNFB E32 0000000000000000 CNEN0D E64 0000000000000000 LATA E06 -----------xxxxx ANSELC E38 --------11--1111 CNSTATD E66 0000000000000000 ODCA E08 -----------00000 TRISC E3A 1111111111111111 CNEN1D E68 0000000000000000 CNPUA E0A -----------00000 PORTC E3C xxxxxxxxxxxxxxxx CNFD E6A 0000000000000000 CNPDA E0C -----------00000 LATC E3E xxxxxxxxxxxxxxxx ANSELE E70 ---------1------ CNEN0A E10 -----------00000 ODCC E40 0000000000000000 TRISE E72 1111111111111111 CNSTATA E12 -----------00000 CNPUC E42 0000000000000000 PORTE E74 xxxxxxxxxxxxxxxx CNEN1A E14 -----------00000 CNPDC E44 0000000000000000 LATE E76 xxxxxxxxxxxxxxxx CNFA E16 -----------00000 CNCONC E46 0---0----------- ODCE E78 0000000000000000 ANSELB E1C -------11--11111 CNEN0C E48 0000000000000000 CNPUE E7A 0000000000000000 TRISB E1E 1111111111111111 CNSTATC E4A 0000000000000000 CNPDE E7C 0000000000000000 PORTB E20 xxxxxxxxxxxxxxxx CNEN1C E4C 0000000000000000 CNCONE E7E 0---0----------- LATB E22 xxxxxxxxxxxxxxxx CNFC E4E 0000000000000000 CNEN0E E80 0000000000000000 ODCB E24 0000000000000000 ANSELD E54 -11111---------- CNSTATE E82 0000000000000000 CNPUB E26 0000000000000000 TRISD E56 1111111111111111 CNEN1E E84 0000000000000000 CNFE E86 0000000000000000 CNPDB E28 0000000000000000 PORTD E58 xxxxxxxxxxxxxxxx CNEN0A E10 -----------00000 LATD E5A xxxxxxxxxxxxxxxx CNCONB E2A 0---0----------- ODCD E5C 0000000000000000 Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Address and Reset values are in hexadecimal and binary, respectively. TABLE 4-15: Register SLAVE SFR BLOCK F00h Address All Resets Register PMD1 F80 00--x-0000000011 PMD2 PMD4 Reset RCON Oscillator Address All Resets Register Address All Resets FA4 ----000-00000-00 REFOTRIM FBE 000000000------- FA6 --------00000000 PCTRAPL FBF 0000000000000000 FAA ------------0--- PCTRAPL FC0 0000000000000000 PCTRAPH FC2 --------00000000 OSCCON F84 -000-xxx0-0-0--0 PMD6 FAE --000000-------- CLKDIV F86 00110000--000001 PMD7 FB0 -------x----0--- PLLFBD F88 ----000010010110 PMD8 FB2 ---00--0--xx000- PLLDIV F8A ------00-011-001 WDT APLLFBD1 F90 ----000010010110 WDTCONL FB4 0--0000000000000 APLLDIV1 F92 ------00-011-001 WDTCONH FB6 0000000000000000 REFOCONL FB8 0-000-00----0000 REFOCONH FBA -000000000000000 PMD PMDCON FA0 ----0----------- Legend: x = unknown or indeterminate value; “-” = unimplemented bits. Reset and address values are in hexadecimal.  2017-2019 Microchip Technology Inc. DS70005319D-page 283 dsPIC33CH128MP508 FAMILY 4.2.4.1 Paged Memory Scheme The dsPIC33CH128MP508S1 architecture extends the available Data Space through a paging scheme, which allows the available Data Space to be accessed using MOV instructions in a linear fashion for pre- and post-modified Effective Addresses (EAs). The upper half of the base Data Space address is used in conjunction with the Data Space Read Page (DSRPAG) register to form the Program Space Visibility (PSV) address. The paged memory scheme provides access to multiple 32-Kbyte windows in the PSV memory. The Data Space Read Page (DSRPAG) register, in combination with the upper half of the Data Space address, can provide up to 8 Mbytes of PSV address space. The paged data memory space is shown in Figure 4-7. The Program Space (PS) can be accessed with a DSRPAG of 0x200 or greater. Only reads from PS are supported using the DSRPAG. The Data Space Read Page (DSRPAG) register is located in the SFR space. Construction of the PSV address is shown in Figure 4-6. When DSRPAG[9] = 1 and the base address bit, EA[15] = 1, the DSRPAG[8:0] bits are concatenated onto EA[14:0] to form the 24-bit PSV read address. FIGURE 4-6: PROGRAM SPACE VISIBILITY (PSV) READ ADDRESS GENERATION 16-Bit DS EA EA[15] = 0 (DSRPAG = don’t care) No EDS Access 0 Byte Select EA EA[15] DSRPAG[9] =1 1 EA Select DSRPAG Generate PSV Address 1 DSRPAG[8:0] 9 Bits 15 Bits 24-Bit PSV EA Byte Select Note: DS read access when DSRPAG = 0x000 will force an address error trap. DS70005319D-page 284  2017-2019 Microchip Technology Inc.  2017-2019 Microchip Technology Inc. FIGURE 4-7: PAGED DATA MEMORY SPACE Table Address Space (TBLPAG[7:0]) Program Space (Instruction & Data) DS_Addr[15:0] 0x0000 Program Memory (lsw – [15:0]) 0x00_0000 DS_Addr[14:0] 0x0000 DS_Addr[15:0] 0xFFFF (DSRPAG = 0x200) No Writes Allowed Local Data Space (TBLPAG = 0x00) lsw Using TBLRDL/TBLWTL, MSB Using TBLRDH/TBLWTH 0x7FFF SFR Registers 0x0FFF 0x1000 0x0000 Up to 4-Kbyte RAM 0x1FFF 0x2000 0x7FFF 0x8000 (DSRPAG = 0x2FF) No Writes Allowed 0x0000 0x7F_FFFF 0x7FFF 0x0000 0xFFFF (DSRPAG = 0x300) No Writes Allowed 0x7FFF PSV Program Memory (MSB) 32-Kbyte PSV Window 0xFFFF 0x0000 Program Memory (MSB – [23:16]) 0x00_0000 (DSRPAG = 0x3FF) No Writes Allowed 0x7FFF DS70005319D-page 285 0x7F_FFFF (TBLPAG = 0x7F) lsw Using TBLRDL/TBLWTL, MSB Using TBLRDH/TBLWTH dsPIC33CH128MP508 FAMILY PSV Program Memory (lsw) 0x0000 dsPIC33CH128MP508 FAMILY When a PSV page overflow or underflow occurs, EA[15] is cleared as a result of the register indirect EA calculation. An overflow or underflow of the EA in the PSV pages can occur at the page boundaries when: • The initial address, prior to modification, addresses the PSV page • The EA calculation uses Pre- or Post-Modified Register Indirect Addressing; however, this does not include Register Offset Addressing In general, when an overflow is detected, the DSRPAG register is incremented and the EA[15] bit is set to keep the base address within the PSV window. When an underflow is detected, the DSRPAG register is decremented and the EA[15] bit is set to keep the base TABLE 4-16: O, Read U, Read U, Read U, Read [++Wn] or [Wn++] [--Wn] or [Wn--] Legend: Note 1: 2: 3: 4: Exceptions to the operation described above arise when entering and exiting the boundaries of Page 0 and PSV spaces. Table 4-16 lists the effects of overflow and underflow scenarios at different boundaries. In the following cases, when overflow or underflow occurs, the EA[15] bit is set and the DSRPAG is not modified; therefore, the EA will wrap to the beginning of the current page: • Register Indirect with Register Offset Addressing • Modulo Addressing • Bit-Reversed Addressing OVERFLOW AND UNDERFLOW SCENARIOS AT PAGE 0 AND PSV SPACE BOUNDARIES(2,3,4) Before O/U, Operation R/W O, Read address within the PSV window. This creates a linear PSV address space, but only when using Register Indirect Addressing modes. DSRPAG DS EA[15] DSRPAG = 0x2FF 1 DSRPAG = 0x3FF After Page Description DSRPAG DS EA[15] Page Description PSV: Last lsw page DSRPAG = 0x300 1 PSV: First MSB page 1 PSV: Last MSB page DSRPAG = 0x3FF 0 See Note 1 DSRPAG = 0x001 1 PSV page DSRPAG = 0x001 0 See Note 1 DSRPAG = 0x200 1 PSV: First lsw page DSRPAG = 0x200 0 See Note 1 DSRPAG = 0x300 1 PSV: First MSB page DSRPAG = 0x2FF 1 PSV: Last lsw page O = Overflow, U = Underflow, R = Read, W = Write The Register Indirect Addressing now addresses a location in the base Data Space (0x0000-0x8000). An EDS access, with DSRPAG = 0x000, will generate an address error trap. Only reads from PS are supported using DSRPAG. Pseudolinear Addressing is not supported for large offsets. DS70005319D-page 286  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY Extended X Data Space The lower portion of the base address space range, between 0x0000 and 0x7FFF, is always accessible, regardless of the contents of the Data Space Read Page register. It is indirectly addressable through the register indirect instructions. It can be regarded as being located in the default EDS Page 0 (i.e., EDS address range of 0x000000 to 0x007FFF with the base address bit, EA[15] = 0, for this address range). However, Page 0 cannot be accessed through the upper 32 Kbytes, 0x8000 to 0xFFFF, of base Data Space in combination with DSRPAG = 0x00. Consequently, DSRPAG is initialized to 0x001 at Reset. Note 1: DSRPAG should not be used to access Page 0. An EDS access with DSRPAG set to 0x000 will generate an address error trap. 2: Clearing the DSRPAG in software has no effect. The remaining PSV pages are only accessible using the DSRPAG register in combination with the upper 32 Kbytes, 0x8000 to 0xFFFF, of the base address, where base address bit, EA[15] = 1. 4.2.4.3 When the PC is pushed onto the stack, PC[15:0] are pushed onto the first available stack word, then PC[22:16] are pushed into the second available stack location. For a PC push during any CALL instruction, the MSB of the PC is zero-extended before the push, as shown in Figure 4-8. During exception processing, the MSB of the PC is concatenated with the lower eight bits of the CPU STATUS Register, SR. This allows the contents of SRL to be preserved automatically during interrupt processing. Note 1: To maintain system Stack Pointer (W15) coherency, W15 is never subject to (EDS) paging, and is therefore, restricted to an address range of 0x0000 to 0xFFFF. The same applies to W14 when used as a Stack Frame Pointer (SFA = 1). 2: As the stack can be placed in, and can access X and Y spaces, care must be taken regarding its use, particularly with regard to local automatic variables in a C development environment Software Stack The W15 register serves as a dedicated Software Stack Pointer (SSP), and is automatically modified by exception processing, subroutine calls and returns; however, W15 can be referenced by any instruction in the same manner as all other W registers. This simplifies reading, writing and manipulating the Stack Pointer (for example, creating stack frames). Note: The Software Stack Pointer always points to the first available free word and fills the software stack, working from lower toward higher addresses. Figure 4-8 illustrates how it pre-decrements for a stack pop (read) and post-increments for a stack push (writes). To protect against misaligned stack accesses, W15[0] is fixed to ‘0’ by the hardware. W15 is initialized to 0x1000 during all Resets. This address ensures that the SSP points to valid RAM in all dsPIC33CH128MP508S1 devices and permits stack availability for non-maskable trap exceptions. These can occur before the SSP is initialized by the user software. You can reprogram the SSP during initialization to any location within Data Space.  2017-2019 Microchip Technology Inc. FIGURE 4-8: 0x0000 CALL STACK FRAME 15 0 CALL SUBR Stack Grows Toward Higher Address 4.2.4.2 PC[15:1] b‘000000000’ W15 (before CALL) PC[22:16] [Free Word] W15 (after CALL) DS70005319D-page 287 dsPIC33CH128MP508 FAMILY 4.2.5 INSTRUCTION ADDRESSING MODES The addressing modes shown in Table 4-17 form the basis of the addressing modes optimized to support the specific features of individual instructions. The addressing modes provided in the MAC class of instructions differ from those in the other instruction types. 4.2.5.1 File Register Instructions Most file register instructions use a 13-bit address field (f) to directly address data present in the first 8192 bytes of data memory (Near Data Space). Most file register instructions employ a Working register, W0, which is denoted as WREG in these instructions. The destination is typically either the same file register or WREG (with the exception of the MUL instruction), which writes the result to a register or register pair. The MOV instruction allows additional flexibility and can access the entire Data Space. TABLE 4-17: 4.2.5.2 MCU Instructions The three-operand MCU instructions are of the form: Operand 3 = Operand 1 Operand 2 where Operand 1 is always a Working register (that is, the addressing mode can only be Register Direct), which is referred to as Wb. Operand 2 can be a W register fetched from data memory or a 5-bit literal. The result location can either be a W register or a data memory location. The following addressing modes are supported by MCU instructions: • • • • • Register Direct Register Indirect Register Indirect Post-Modified Register Indirect Pre-Modified 5-Bit or 10-Bit Literal Note: Not all instructions support all the addressing modes given above. Individual instructions can support different subsets of these addressing modes. FUNDAMENTAL ADDRESSING MODES SUPPORTED Addressing Mode Description File Register Direct The address of the file register is specified explicitly. Register Direct The contents of a register are accessed directly. Register Indirect The contents of Wn form the Effective Address (EA). Register Indirect Post-Modified The contents of Wn form the EA. Wn is post-modified (incremented or decremented) by a constant value. Register Indirect Pre-Modified Wn is pre-modified (incremented or decremented) by a signed constant value to form the EA. Register Indirect with Register Offset The sum of Wn and Wb forms the EA. (Register Indexed) Register Indirect with Literal Offset DS70005319D-page 288 The sum of Wn and a literal forms the EA.  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 4.2.5.3 Move and Accumulator Instructions Move instructions, and the DSP accumulator class of instructions, provide a greater degree of addressing flexibility than other instructions. In addition to the addressing modes supported by most MCU instructions, move and accumulator instructions also support Register Indirect with Register Offset Addressing mode, also referred to as Register Indexed mode. Note: For the MOV instructions, the addressing mode specified in the instruction can differ for the source and destination EA. However, the 4-bit Wb (Register Offset) field is shared by both source and destination (but typically only used by one). 4.2.5.4 The dual source operand DSP instructions (CLR, ED, EDAC, MAC, MPY, MPY.N, MOVSAC and MSC), also referred to as MAC instructions, use a simplified set of addressing modes to allow the user application to effectively manipulate the Data Pointers through register indirect tables. The two-source operand prefetch registers must be members of the set {W8, W9, W10, W11}. For data reads, W8 and W9 are always directed to the X RAGU, and W10 and W11 are always directed to the Y AGU. The Effective Addresses generated (before and after modification) must therefore, be valid addresses within X Data Space for W8 and W9, and Y Data Space for W10 and W11. Note: In summary, the following addressing modes are supported by move and accumulator instructions: • • • • • • • • Register Direct Register Indirect Register Indirect Post-Modified Register Indirect Pre-Modified Register Indirect with Register Offset (Indexed) Register Indirect with Literal Offset 8-Bit Literal 16-Bit Literal Note: Not all instructions support all the addressing modes given above. Individual instructions may support different subsets of these addressing modes.  2017-2019 Microchip Technology Inc. MAC Instructions Register Indirect with Register Offset Addressing mode is available only for W9 (in X space) and W11 (in Y space). In summary, the following addressing modes are supported by the MAC class of instructions: • • • • • Register Indirect Register Indirect Post-Modified by 2 Register Indirect Post-Modified by 4 Register Indirect Post-Modified by 6 Register Indirect with Register Offset (Indexed) 4.2.5.5 Other Instructions Besides the addressing modes outlined previously, some instructions use literal constants of various sizes. For example, BRA (branch) instructions use 16-bit signed literals to specify the branch destination directly, whereas the DISI instruction uses a 14-bit unsigned literal field. In some instructions, such as ULNK, the source of an operand or result is implied by the opcode itself. Certain operations, such as a NOP, do not have any operands. DS70005319D-page 289 dsPIC33CH128MP508 FAMILY 4.2.6 MODULO ADDRESSING 4.2.6.1 Modulo Addressing mode is a method of providing an automated means to support circular data buffers using hardware. The objective is to remove the need for software to perform data address boundary checks when executing tightly looped code, as is typical in many DSP algorithms. Start and End Address The Modulo Addressing scheme requires that a starting and ending address be specified and loaded into the 16-bit Modulo Buffer Address registers: XMODSRT, XMODEND, YMODSRT and YMODEND (see Table 4-1). Note: Y space Modulo Addressing EA calculations assume word-sized data (LSb of every EA is always clear). Modulo Addressing can operate in either Data or Program Space (since the Data Pointer mechanism is essentially the same for both). One circular buffer can be supported in each of the X (which also provides the pointers into Program Space) and Y Data Spaces. Modulo Addressing can operate on any W Register Pointer. However, it is not advisable to use W14 or W15 for Modulo Addressing since these two registers are used as the Stack Frame Pointer and Stack Pointer, respectively. The length of a circular buffer is not directly specified. It is determined by the difference between the corresponding start and end addresses. The maximum possible length of the circular buffer is 32K words (64 Kbytes). In general, any particular circular buffer can be configured to operate in only one direction, as there are certain restrictions on the buffer start address (for incrementing buffers) or end address (for decrementing buffers), based upon the direction of the buffer. The Modulo and Bit-Reversed Addressing Control register, MODCON[15:0], contains enable flags, as well as a W register field to specify the W Address registers. The XWM and YWM fields select the registers that operate with Modulo Addressing: The only exception to the usage restrictions is for buffers that have a power-of-two length. As these buffers satisfy the start and end address criteria, they can operate in a Bidirectional mode (that is, address boundary checks are performed on both the lower and upper address boundaries). • If XWM = 1111, X RAGU and X WAGU Modulo Addressing is disabled • If YWM = 1111, Y AGU Modulo Addressing is disabled 4.2.6.2 W Address Register Selection The X Address Space Pointer W (XWM) register, to which Modulo Addressing is to be applied, is stored in MODCON[3:0] (see Table 4-1). Modulo Addressing is enabled for X Data Space when XWM is set to any value other than ‘1111’ and the XMODEN bit is set (MODCON[15]). The Y Address Space Pointer W (YWM) register, to which Modulo Addressing is to be applied, is stored in MODCON[7:4]. Modulo Addressing is enabled for Y Data Space when YWM is set to any value other than ‘1111’ and the YMODEN bit (MODCON[14]) is set. FIGURE 4-9: MODULO ADDRESSING OPERATION EXAMPLE Byte Address 0x1100 0x1163 Start Addr = 0x1100 End Addr = 0x1163 Length = 0x0032 words DS70005319D-page 290 MOV MOV MOV MOV MOV MOV #0x1100, W0 W0, XMODSRT #0x1163, W0 W0, MODEND #0x8001, W0 W0, MODCON MOV #0x0000, W0 ;W0 holds buffer fill value MOV #0x1110, W1 ;point W1 to buffer DO AGAIN, #0x31 MOV W0, [W1++] AGAIN: INC W0, W0 ;set modulo start address ;set modulo end address ;enable W1, X AGU for modulo ;fill the 50 buffer locations ;fill the next location ;increment the fill value  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 4.2.6.3 Modulo Addressing Applicability Modulo Addressing can be applied to the Effective Address (EA) calculation associated with any W register. Address boundaries check for addresses equal to: • The upper boundary addresses for incrementing buffers • The lower boundary addresses for decrementing buffers It is important to realize that the address boundaries check for addresses less than, or greater than, the upper (for incrementing buffers) and lower (for decrementing buffers) boundary addresses (not just equal to). Address changes can, therefore, jump beyond boundaries and still be adjusted correctly. Note: 4.2.7 The modulo corrected Effective Address is written back to the register only when Pre-Modify or Post-Modify Addressing mode is used to compute the Effective Address. When an address offset (such as [W7 + W2]) is used, Modulo Addressing correction is performed, but the contents of the register remain unchanged. BIT-REVERSED ADDRESSING Bit-Reversed Addressing mode is intended to simplify data reordering for radix-2 FFT algorithms. It is supported by the X AGU for data writes only. The modifier, which can be a constant value or register contents, is regarded as having its bit order reversed. The address source and destination are kept in normal order. Thus, the only operand requiring reversal is the modifier. 4.2.7.1 Bit-Reversed Addressing Implementation Bit-Reversed Addressing mode is enabled in any of these situations: • BWMx bits (W register selection) in the MODCON register are any value other than ‘1111’ (the stack cannot be accessed using Bit-Reversed Addressing) • The BREN bit is set in the XBREV register • The addressing mode used is Register Indirect with Pre-Increment or Post-Increment If the length of a bit-reversed buffer is M = 2N bytes, the last ‘N’ bits of the data buffer start address must be zeros. XB[14:0] is the Bit-Reversed Addressing modifier, or ‘pivot point’, which is typically a constant. In the case of an FFT computation, its value is equal to half of the FFT data buffer size. Note: All bit-reversed EA calculations assume word-sized data (LSb of every EA is always clear). The XB value is scaled accordingly to generate compatible (byte) addresses. When enabled, Bit-Reversed Addressing is executed only for Register Indirect with Pre-Increment or PostIncrement Addressing and word-sized data writes. It does not function for any other addressing mode or for byte-sized data and normal addresses are generated instead. When Bit-Reversed Addressing is active, the W Address Pointer is always added to the address modifier (XB) and the offset associated with the Register Indirect Addressing mode is ignored. In addition, as word-sized data are a requirement, the LSb of the EA is ignored (and always clear). Note: Modulo Addressing and Bit-Reversed Addressing can be enabled simultaneously using the same W register, but BitReversed Addressing operation will always take precedence for data writes when enabled. If Bit-Reversed Addressing has already been enabled by setting the BREN (XBREV[15]) bit, a write to the XBREV register should not be immediately followed by an indirect read operation using the W register that has been designated as the Bit-Reversed Pointer.  2017-2019 Microchip Technology Inc. DS70005319D-page 291 dsPIC33CH128MP508 FAMILY FIGURE 4-10: BIT-REVERSED ADDRESSING EXAMPLE Sequential Address b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 0 Bit Locations Swapped Left-to-Right Around Center of Binary Value b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b1 b2 b3 b4 0 Bit-Reversed Address Pivot Point TABLE 4-18: XB = 0x0008 for a 16-Word Bit-Reversed Buffer BIT-REVERSED ADDRESSING SEQUENCE (16-ENTRY) Normal Address Bit-Reversed Address A3 A2 A1 A0 Decimal A3 A2 A1 A0 Decimal 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 8 0 0 1 0 2 0 1 0 0 4 0 0 1 1 3 1 1 0 0 12 0 1 0 0 4 0 0 1 0 2 0 1 0 1 5 1 0 1 0 10 0 1 1 0 6 0 1 1 0 6 0 1 1 1 7 1 1 1 0 14 1 0 0 0 8 0 0 0 1 1 1 0 0 1 9 1 0 0 1 9 1 0 1 0 10 0 1 0 1 5 1 0 1 1 11 1 1 0 1 13 1 1 0 0 12 0 0 1 1 3 1 1 0 1 13 1 0 1 1 11 1 1 1 0 14 0 1 1 1 7 1 1 1 1 15 1 1 1 1 15 DS70005319D-page 292  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 4.2.8 INTERFACING PROGRAM AND DATA MEMORY SPACES Table instructions allow an application to read small areas of the program memory. This capability makes the method ideal for accessing data tables that need to be updated periodically. It also allows access to all bytes of the program word. The remapping method allows an application to access a large block of data on a read-only basis, which is ideal for look-ups from a large table of static data. However, this method only provides visibility to the lower 16 bits in each location addressed. The dsPIC33CH128MP508S1 family architecture uses a 24-bit wide Program Space (PS) and a 16-bit wide Data Space (DS). The architecture is also a modified Harvard scheme, meaning that data can also be present in the Program Space. To use these data successfully, they must be accessed in a way that preserves the alignment of information in both spaces. Aside from normal execution, the architecture of the dsPIC33CH128MP508S1 family devices provides two methods by which Program Space can be accessed during operation: • Using table instructions to access individual bytes or words anywhere in the Program Space • Remapping a portion of the Program Space into the Data Space (Program Space Visibility) TABLE 4-19: PROGRAM SPACE ADDRESS CONSTRUCTION Instruction Access (Code Execution) User TBLRD (Byte/Word Read) User FIGURE 4-11: Program Space Address Access Space Access Type [23] [22:16] [15] [14:1] [0] PC[22:1] 0 0 0xxx xxxx xxxx xxxx xxxx xxx0 TBLPAG[7:0] Data EA[15:0] 0xxx xxxx xxxx xxxx xxxx xxxx DATA ACCESS FROM PROGRAM SPACE ADDRESS GENERATION Program Counter(1) Program Counter 0 0 23 Bits EA Table Operations(2) 1/0 TBLPAG 1/0 8 Bits 16 Bits 24 Bits User/Configuration Space Select Note 1: 2: Byte Select The Least Significant bit (LSb) of Program Space addresses is always fixed as ‘0’ to maintain word alignment of data in the Program and Data Spaces. Table operations are not required to be word-aligned. Table Read operations are permitted in the configuration memory space.  2017-2019 Microchip Technology Inc. DS70005319D-page 293 dsPIC33CH128MP508 FAMILY 4.2.8.1 Data Access from Program Memory Using Table Instructions The TBLRDL instruction offers a direct method of reading the lower word of any address within the Program Space without going through Data Space. The TBLRDH instruction is the only method to read the upper eight bits of a Program Space word as data. This allows program memory addresses to directly map to Data Space addresses. Program memory can thus be regarded as two 16-bit wide word address spaces, residing side by side, each with the same address range. TBLRDL accesses the space that contains the least significant data word. TBLRDH accesses the space that contains the upper data byte. Two table instructions are provided to read byte or word-sized (16-bit) data from Program Space. Both function as either byte or word operations. FIGURE 4-12: • TBLRDL (Table Read Low): - In Word mode, this instruction maps the lower word of the Program Space location (P[15:0]) to a data address (D[15:0]). - In Byte mode, either the upper or lower byte of the lower program word is mapped to the lower byte of a data address. The upper byte is selected when Byte Select is ‘1’; the lower byte is selected when it is ‘0’. • TBLRDH (Table Read High): - In Word mode, this instruction maps the entire upper word of a program address (P[23:16]) to a data address. The ‘phantom’ byte (D[15:8]) is always ‘0’. - In Byte mode, either the upper or lower byte of the upper program word is mapped to the lower byte of a data address. The upper byte is selected when Byte Select is ‘1’; the lower byte is selected when it is ‘0’. When the upper byte is selected, the ‘phantom’ byte is read as ‘0’. ACCESSING PROGRAM MEMORY WITH TABLE INSTRUCTIONS Program Space TBLPAG 02 23 15 0 0x000000 23 16 8 0 00000000 0x020000 0x030000 00000000 00000000 00000000 ‘Phantom’ Byte TBLRDH.B (Wn[0] = 0) TBLRDL.B (Wn[0] = 1) TBLRDL.B (Wn[0] = 0) TBLRDL.W 0x800000 DS70005319D-page 294 The address for the table operation is determined by the data EA within the page defined by the TBLPAG register. Only read operations are shown; write operations are also valid in the user memory area.  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 4.3 Slave PRAM Program Memory Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “Dual Partition Flash Program Memory” (www.microchip.com/ DS70005156) in the “dsPIC33/PIC24 Family Reference Manual”. 2: Though the reference to the chapter is “Dual Partition Flash Program Memory” (www.microchip.com/DS70005156), the program memory for the Slave code is PRAM. Therefore, after each POR, the Master will have to reload the content of the Slave PRAM. The dsPIC33CH128MP508S1 family devices contain internal PRAM program memory for storing and executing application code. The PRAM program memory array is organized into rows of 128 instructions or 64 double instruction words. Though the PRAM is volatile, it is writable during normal operation over the entire VDD range. PRAM memory can be programmed in two ways: • In-Circuit Serial Programming™ (ICSP™) • Master to Slave Image Loading (MSIL) ICSP allows for a dsPIC33CH128MP508S1 family device to be serially programmed in the application circuit. Since the Slave PRAM is volatile, Slave PRAM ICSP programming is supported only as a development and debugging feature. Master to Slave Image Loading (MSIL) allows the Master user code to load the Slave PRAM at run time. A Slave PRAM compatible image is stored in Master Flash memory. At run time, the Master user code is responsible for loading and verifying the contents of the Slave PRAM. Note: 4.3.1 PRAM PROGRAMMING OPERATIONS Unlike when self-programming the Master Flash, TBLWTL and TBLWTH instructions are not supported during user application mode. This means that RTSP programming of the PRAM is not supported. For ICSP programming of the Slave PRAM, TBLWTL and TBLWTH instructions are used to write to the NVM write latches. An NVM write operation then writes the contents of both latches to the PRAM, starting at the address defined in the NVMADR and NVMADRU registers. For Master to Slave Image Loading (MSIL) of the Slave PRAM, the Master user code is responsible for transferring the Slave image contents, stored in the Master Flash, to the Slave PRAM. The LDSLV instruction is used, along with the DSRPAG and DSWPAG registers, to transfer a single 24-bit instruction to the Slave PRAM. The VFSLV instruction allows the Master user code to verify that the PRAM has been loaded correctly. Note: Master to Slave Image Loading is the only supported method for programming the Slave PRAM in a final user application. Regardless of the method used to program the PRAM, a few basic requirements should be met: • A full 48-bit double instruction word should always be programmed to a PRAM location. Either instruction may simply be a NOP to fulfill this requirement. This ensures a valid ECC value is generated for each pair of instructions written. • Assuming the above step is followed, the last 24-bit location in implemented Program Space, or prior to any unprogrammed region in Program Space, should never be executed. The penultimate instruction, in either case, must contain a program flow change instruction, such as a RETURN or a BRA instruction. In an actual application mode, the Slave PRAM is loaded by the Master, so the ICSP mode of PRAM operation is valid only for the Debug mode during the code development.  2017-2019 Microchip Technology Inc. DS70005319D-page 295 dsPIC33CH128MP508 FAMILY 4.3.2 MASTER TO SLAVE IMAGE LOADING (MSIL) Master to Slave Image Loading (MSIL) allows the Master user application code to transfer the Slave image, stored in the Master Flash, to the Slave PRAM. This is the only supported method for programming the Slave PRAM in a final user application. The LDSLV instruction is executed by the Master user application to transfer a single 24-bit instruction from the Master Flash address, defined by Ws[14:0] (DSRPAG), to the Slave PRAM address, defined by Wd[14:0] (DSWPAG). The LDSLV instruction should be executed in pairs to ensure correct ECC value generation for each double instruction word that is loaded into the Slave PRAM. The Slave image instruction found at a given even address should be loaded first. This will be the lower instruction word of a 48-bit double instruction word. The upper instruction word should then be loaded from the following odd address. After the pair of LDSLV instructions is executed by the Master user application, both 24-bit Slave image instructions and the generated 7-bit ECC value are actually loaded into the PRAM destination address locations. The __program_slave() routine uses the “verify” parameter as a switch to either load or verify the Slave image using the LDSLV or VFSLV instructions. A ‘0’ will load the entire Slave image to the PRAM and a ‘1’ will verify the entire Slave image in the PRAM. An example of how this routine can be used to load and verify the contents of the Slave PRAM is shown in Example 4-1. EXAMPLE 4-1: SLAVE PRAM LOAD AND VERIFY ROUTINE #include [libpic30.h] //_program_slave(core#, verify, &slave_image) if (_program_slave(l, 0, &slave_image) == 0) { /* now verify */ if (_program_slave(l, 1, &slave_image) == ESLV_VERIFY_FAIL) { asm(“reset”) ; // try again } } Slave PRAM images not following the Microchip language tool format will require a custom routine that follows all requirements for the PRAM Master to Slave Image Loading process described in this chapter. The VFSLV instruction allows the Master user application to verify that the PRAM has been loaded correctly. The VFSLV instruction compares the 24-bit instruction word stored in the Master Flash address, defined by Ws[14:0] (DSRPAG), to the 24 bit instruction written to the Slave PRAM address, defined by Wd[14:0] (DSWPAG). The __start_slave routine is used to start the Slave core after it has had it’s image loaded by the Master core. If an application requires the Slave core to be stopped, the __stop_slave routine is also provided. Example usage of these routines are shown in Example 4-2. The VFSLV instruction should also be executed in pairs. The lower instruction word found on a given even address should be verified first. The upper instruction word found in the following odd address should then be verified. Then, the Slave image instruction pair read from the Master Flash will have a valid generated ECC value. This full double instruction word with ECC is then compared to the 55-bit value that was actually loaded into the PRAM destination locations. The entire Slave image may be loaded into the PRAM first and then subsequently verified. EXAMPLE 4-2: 4.3.3 The __start_slave and __stop_slave routines perform the MSl1KEY unlock sequence and set or clear the SLVEN bit (MSl1CON[15]). USING DEVELOPMENT TOOL SUPPORTED FUNCTIONS The Microchip development environment provides some utility functions to simplify loading the Slave image and starting the Slave core operation. The __program_slave() routine within the libpic30.h library programs the Slave core with the specified Slave image created within the Microchip language tool format. DS70005319D-page 296 SLAVE START AND STOP EXAMPLE #include [libpic30.h] int main() { // Master intialization code _start_slave(); // Start Slave core // Master application code _stop_slave(); // Stop Slave core while(1); }  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 4.3.4 PRAM DUAL PARTITION CONSIDERATIONS For dsPIC33CH512MP508S1 family devices operating in Dual Partition PRAM Program Memory modes, both partitions would be loaded using the Master to Slave Image Loading process. The Master can load the Active Partition of the PRAM only when SLVEN = 0 (Slave is not running). The Master can load the PRAM Inactive Partition any time. To support LiveUpdate, the Master would load the PRAM Inactive Partition while the Slave is running and then the Slave would execute the BOOTSWP instruction to swap partitions. 4.3.4.1 PRAM Partition Swapping At device Reset, the default PRAM partition is Partition 1. The BOOTSWP instruction provides the means of swapping the Active and Inactive Partitions (soft swap) without the need for a device Reset. The BOOTSWP must always be followed by a GOTO instruction. The BOOTSWP instruction swaps the Active and Inactive Partitions, and the PC vectors to the location specified by the GOTO instruction in the newly Active Partition. It is important to note that interrupts should temporarily be disabled while performing the soft swap sequence, and that after the partition swap, all peripherals and interrupts, which were enabled remain enabled. Additionally, the RAM and stack will maintain their state after the switch. As a result, it is recommended that applications using soft swaps jump to a routine that will reinitialize the device in order to ensure the firmware runs as expected. The Configuration registers will have no effect during a soft swap. 4.3.5 ERROR CORRECTING CODE (ECC) In order to improve program memory performance and durability, these devices include Error Correcting Code functionality (ECC) as an integral part of the PRAM memory controller. ECC can determine the presence of single bit errors in program data, including which bit is in error, and correct the data automatically without user intervention. ECC cannot be disabled. When data are written to program memory, ECC generates a 7-bit Hamming code parity value for every two (24-bit) instruction words. The data are stored in blocks of 48 data bits and seven parity bits; parity data are not memory-mapped and are inaccessible. When the data are read back, the ECC calculates the parity on them and compares it to the previously stored parity value. If a parity mismatch occurs, there are two possible outcomes: • Single bit errors are automatically identified and corrected on read back. An optional device-level interrupt (ECCSBEIF) is also generated. • Double-bit errors will generate a generic hard trap and the read data are not changed. If special exception handling for the trap is not implemented, a device Reset will also occur. To use the single bit error interrupt, set the ECC Single Bit Error Interrupt Enable bit (ECCSBEIE) and configure the ECCSBEIPx bits to set the appropriate interrupt priority. Except for the single bit error interrupt, error events are not captured or counted by hardware. This functionality can be implemented in the software application, but it is the user’s responsibility to do so. 4.3.6 CONTROL REGISTERS Six SFRs are used to write and erase the Program Flash Memory: NVMCON, NVMKEY, NVMADR, NVMADRU, NVMSRCADRL and NVMSRCADRH. The NVMCON register (Register 4-4) selects the operation to be performed (page erase, word/row program, Inactive Partition erase) and initiates the program or erase cycle. NVMKEY (Register 4-7) is a write-only register that is used for write protection. To start a programming or erase sequence, the user application must consecutively write 0x55 and 0xAA to the NVMKEY register. There are two NVM Address registers: NVMADRU and NVMADR. These two registers, when concatenated, form the 24-bit Effective Address (EA) of the selected word/row for programming operations, or the selected page for erase operations. The NVMADRU register is used to hold the upper eight bits of the EA, while the NVMADR register is used to hold the lower 16 bits of the EA. For row programming operation, data to be written to the Slave PRAM are written into Slave data memory space (RAM) at an address defined by the NVMSRCADRL/H registers (location of first element in row programming data).  2017-2019 Microchip Technology Inc. DS70005319D-page 297 dsPIC33CH128MP508 FAMILY 4.3.7 SLAVE PROGRAM MEMORY CONTROL/STATUS REGISTERS REGISTER 4-4: NVMCON: PROGRAM MEMORY SLAVE CONTROL REGISTER R/SO-0(1) R/W-0(1) R/W-0(1) R/W-0 R/C-0 R/C-0 R/W-0 R/C-0 WR WREN WRERR NVMSIDL(2) SFTSWP P2ACTIV RPDF URERR bit 15 bit 8 U-0 U-0 — — U-0 — U-0 R/W-0(1) R/W-0(1) — R/W-0(1) NVMOP[3:0] R/W-0(1) (3,4) bit 7 bit 0 Legend: C = Clearable bit SO = Settable Only bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 WR: Write Control bit(1) 1 = Initiates a PRAM memory program or erase operation; the operation is self-timed and the bit is cleared by hardware once the operation is complete 0 = Program or erase operation is complete and inactive bit 14 WREN: Write Enable bit(1) 1 = Enables program/erase operations 0 = Inhibits program/erase operations bit 13 WRERR: Write Sequence Error Flag bit(1) 1 = An improper program or erase sequence attempt, or termination has occurred (bit is set automatically on any set attempt of the WR bit) 0 = The program or erase operation completed normally bit 12 NVMSIDL: PRAM Stop in Idle Control bit(2) 1 = PRAM voltage regulator goes into Standby mode during Idle mode 0 = PRAM voltage regulator is active during Idle mode bit 11 SFTSWP: Soft Swap Status bit 1 = Panels have been successfully swapped using the BOOTSWP instruction 0 = Awaiting for panels to be successfully swapped using the BOOTSWP instruction bit 10 P2ACTIV: Dual Boot Active Region Status bit 1 = Panel 2 PRAM is mapped into the active region 0 = Panel 1 PRAM is mapped into the active region bit 9 RPDF: Row Programming Data Format bit 1 = Row data to be stored in PRAM are in compressed format 0 = Row data to be stored in PRAM are in uncompressed format bit 8 URERR: Row Programming Data Underrun Error bit 1 = Indicates row programming operation has been terminated 0 = No data underrun error is detected bit 7-4 Unimplemented: Read as ‘0’ Note 1: 2: 3: 4: 5: These bits can only be reset on a POR. If this bit is set, there will be minimal power savings (IIDLE) and upon exiting Idle mode, there is a delay (TVREG) before PRAM memory becomes operational. All other combinations of NVMOP[3:0] are unimplemented. Execution of the PWRSAV instruction is ignored while any of the NVM operations are in progress. Two adjacent words on a 4-word boundary are programmed during execution of this operation. DS70005319D-page 298  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-4: NVMCON: PROGRAM MEMORY SLAVE CONTROL REGISTER (CONTINUED) NVMOP[3:0]: NVM Operation Select bits(1,3,4) 1111 = Reserved ... 0101 = Reserved 0100 = Inactive Partition memory erase operation 0011 = Reserved 0010 = Reserved 0001 = Memory double-word program operation(5) 0000 = Reserved bit 3-0 Note 1: 2: 3: 4: 5: These bits can only be reset on a POR. If this bit is set, there will be minimal power savings (IIDLE) and upon exiting Idle mode, there is a delay (TVREG) before PRAM memory becomes operational. All other combinations of NVMOP[3:0] are unimplemented. Execution of the PWRSAV instruction is ignored while any of the NVM operations are in progress. Two adjacent words on a 4-word boundary are programmed during execution of this operation.  2017-2019 Microchip Technology Inc. DS70005319D-page 299 dsPIC33CH128MP508 FAMILY REGISTER 4-5: R/W-x NVMADR: SLAVE PROGRAM MEMORY LOWER ADDRESS REGISTER R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x NVMADR[15:8] bit 15 bit 8 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x NVMADR[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown NVMADR[15:0]: PRAM Memory Lower Write Address bits Selects the lower 16 bits of the location to program or erase in PRAM. This register may be read or written to by the user application. REGISTER 4-6: NVMADRU: SLAVE PROGRAM MEMORY UPPER ADDRESS REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x NVMADRU[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7-0 NVMADRU[23:16]: PRAM Memory Upper Write Address bits Selects the upper eight bits of the location to program or erase in PRAM. This register may be read or written to by the user application. DS70005319D-page 300  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-7: NVMKEY: SLAVE NONVOLATILE MEMORY KEY REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 NVMKEY[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-8 Unimplemented: Read as ‘0’ bit 7-0 NVMKEY[7:0]: NVM Key Register bits (write-only)  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 301 dsPIC33CH128MP508 FAMILY REGISTER 4-8: R/W-0 NVMSRCADRL: SLAVE NVM SOURCE DATA ADDRESS REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 NVMSRCADR[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 NVMSRCADR[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown NVMSRCADR[15:0]: NVM Source Data Address bits The RAM address of the data to be programmed into PRAM when the NVMOP[3:0] bits are set to row programming. REGISTER 4-9: NVMSRCADRH: SLAVE NVM SOURCE DATA ADDRESS REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 NVMSRCADR[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7-0 NVMSRCADR[23:16]: NVM Source Data Address bits The RAM address of the data to be programmed into PRAM when the NVMOP[3:0] bits are set to row programming. DS70005319D-page 302  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 4.3.8 SLAVE ECC CONTROL/STATUS REGISTERS REGISTER 4-10: ECCCONL: ECC FAULT INJECTION CONFIGURATION REGISTER LOW U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — — FLTINMJ bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-1 Unimplemented: Read as ‘0’ bit 0 FLTINJ: Fault Injection Sequence Enable bit 1 = Enabled 0 = Disabled REGISTER 4-11: R/W-0 x = Bit is unknown ECCCONH: ECC FAULT INJECTION CONFIGURATION REGISTER HIGH R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FLT2PTR[7:0] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FLT1PTR[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 FLT2PTR[7:0]: ECC Fault Injection Bit Pointer 2 bits 11111111-10001001 = No Fault injection occurs 10001000 = Fault injection (bit inversion) occurs on bit 136 of ECC bit order ... 00000001 = Fault injection occurs on bit 1 of ECC bit order 00000000 = Fault injection occurs on bit 0 of ECC bit order bit 7-0 FLT1PTR[7:0]: ECC Fault Injection Bit Pointer 1 bits 1111111-10001001 = No Fault injection occurs 10001000 = Fault injection (bit inversion) occurs on bit 136 of ECC bit order ... 00000001 = Fault injection (bit inversion) occurs on bit 1 of ECC bit order 00000000 = Fault injection (bit inversion) occurs on bit 0 of ECC bit order  2017-2019 Microchip Technology Inc. DS70005319D-page 303 dsPIC33CH128MP508 FAMILY REGISTER 4-12: R/W-0 ECCADDRL: ECC FAULT INJECT ADDRESS COMPARE REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ECCADDR[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ECCADDR[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown ECCADDR[15:0]: ECC Fault Injection NVM Address Match Compare bits REGISTER 4-13: R/W-0 ECCADDRH: ECC FAULT INJECT ADDRESS COMPARE REGISTER HIGH R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ECCADDR[31:24] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ECCADDR[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown ECCADDR[31:16]: ECC Fault Injection NVM Address Match Compare bits DS70005319D-page 304  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-14: R/W-0 ECCSTATL: ECC SYSTEM STATUS DISPLAY REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SECOUT[7:0] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SECIN[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 SECOUT[7:0]: Calculated Single Error Correction Parity Value bits Indicates the latches’ SEC output parity bits, generated by the ECC XOR tree logic, based on the data portion of the word being read. bit 7-0 SECIN[7:0]: Read Single Error Correction Parity Value bits Indicates the latched value of input parity from a previous read address match. REGISTER 4-15: ECCSTATH: ECC SYSTEM STATUS DISPLAY REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 — — — — — — DEDOUT DEDIN bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SECSYND[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-10 Unimplemented: Read as ‘0’ bit 9 DEDOUT: Dual Bit Error Detection Flag bit Indicates the latched value of the DED parity out from a previous read address match. 1 = Dual bit error has occurred 0 = No dual bit error has occurred bit 8 DEDIN: Dual Bit Error Read Parity bit 1 = DED in parity is set 0 = DED in parity is not set bit 7-0 SECSYND[7:0]: Calculated ECC Syndrome Value bits  2017-2019 Microchip Technology Inc. DS70005319D-page 305 dsPIC33CH128MP508 FAMILY 4.4 Slave Resets Any active source of Reset will make the SYSRST signal active. On system Reset, some of the registers associated with the CPU and peripherals are forced to a known Reset state, and some are unaffected. Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “Reset” (www.microchip.com/ DS70602) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). Note: All types of device Reset set a corresponding status bit in the RCON register to indicate the type of Reset (see Register 4-16). The Reset module combines all Reset sources and controls the device Master Reset Signal, SYSRST. The following is a list of device Reset sources: • • • • • • • • A POR clears all the bits, except for the BOR and POR bits (RCON[1:0]) that are set. The user application can set or clear any bit, at any time, during code execution. The RCON bits only serve as status bits. Setting a particular Reset status bit in software does not cause a device Reset to occur. POR: Power-on Reset BOR: Brown-out Reset MCLR: Master Clear Pin Reset SWR: RESET Instruction WDTO: Watchdog Timer Time-out Reset CM: Configuration Mismatch Reset TRAPR: Trap Conflict Reset IOPUWR: Illegal Condition Device Reset - Illegal Opcode Reset - Uninitialized W Register Reset - Security Reset The RCON register also has other bits associated with the Watchdog Timer and device power-saving states. The function of these bits is discussed in other sections of this data sheet. Note: The status bits in the RCON register should be cleared after they are read so that the next RCON register value after a device Reset is meaningful. For all Resets, the default clock source is determined by the FNOSC[2:0] bits in the FOSCSEL Configuration register. The value of the FNOSCx bits is loaded into the NOSC[2:0] (OSCCON[10:8]) bits on Reset, which in turn, initializes the system clock. A simplified block diagram of the Reset module is shown in Figure 4-13. FIGURE 4-13: Refer to the specific peripheral section or Section 4.2 “Slave Memory Organization” of this data sheet for register Reset states. RESET SYSTEM BLOCK DIAGRAM RESET Instruction Glitch Filter MCLR, S1MCLR1, S1MCLR2, S1MCLR3 VDD WDT Module Sleep or Idle BOR Internal Regulator SYSRST VDD Rise Detect POR Trap Conflict Illegal Opcode Uninitialized W Register Security Reset Configuration Mismatch DS70005319D-page 306  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 4.4.1 RESET RESOURCES Many useful resources are provided on the main product page of the Microchip website for the devices listed in this data sheet. This product page contains the latest updates and additional information.  2017-2019 Microchip Technology Inc. 4.4.1.1 Key Resources • “Reset” (www.microchip.com/DS70602) in the “dsPIC33/PIC24 Family Reference Manual” • Code Samples • Application Notes • Software Libraries • Webinars • All Related “dsPIC33/PIC24 Family Reference Manual” Sections • Development Tools DS70005319D-page 307 dsPIC33CH128MP508 FAMILY 4.4.2 SLAVE RESET CONTROL REGISTER RCON: RESET CONTROL REGISTER(1) REGISTER 4-16: R/W-0 R/W-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 TRAPR IOPUWR — — — — CM VREGS bit 15 bit 8 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-1 R/W-1 EXTR SWR — WDTO SLEEP IDLE BOR POR bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 TRAPR: Trap Reset Flag bit 1 = A Trap Conflict Reset has occurred 0 = A Trap Conflict Reset has not occurred bit 14 IOPUWR: Illegal Opcode or Uninitialized W Register Access Reset Flag bit 1 = An Illegal Opcode, an Illegal Address mode or Uninitialized W Register used as an Address Pointer caused a Reset 0 = An Illegal Opcode or Uninitialized W Register Reset has not occurred bit 13-10 Unimplemented: Read as ‘0’ bit 9 CM: Configuration Mismatch Flag bit 1 = A Configuration Mismatch Reset has occurred. 0 = A Configuration Mismatch Reset has not occurred bit 8 VREGS: Voltage Regulator Standby During Sleep bit 1 = Voltage regulator is active during Sleep 0 = Voltage regulator goes into Standby mode during Sleep bit 7 EXTR: External Reset (MCLR, S1MCLRx) Pin bit 1 = A Master Clear (pin) Reset has occurred 0 = A Master Clear (pin) Reset has not occurred bit 6 SWR: Software RESET (Instruction) Flag bit 1 = A RESET instruction has been executed 0 = A RESET instruction has not been executed bit 5 Unimplemented: Read as ‘0’ bit 4 WDTO: Watchdog Timer Time-out Flag bit 1 = WDT time-out has occurred 0 = WDT time-out has not occurred bit 3 SLEEP: Wake-up from Sleep Flag bit 1 = Device has been in Sleep mode 0 = Device has not been in Sleep mode bit 2 IDLE: Wake-up from Idle Flag bit 1 = Device has been in Idle mode 0 = Device has not been in Idle mode bit 1 BOR: Brown-out Reset Flag bit 1 = A Brown-out Reset has occurred 0 = A Brown-out Reset has not occurred Note 1: All of the Reset status bits can be set or cleared in software. Setting one of these bits in software does not cause a device Reset. DS70005319D-page 308  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-16: bit 0 Note 1: RCON: RESET CONTROL REGISTER(1) (CONTINUED) POR: Power-on Reset Flag bit 1 = A Power-on Reset has occurred 0 = A Power-on Reset has not occurred All of the Reset status bits can be set or cleared in software. Setting one of these bits in software does not cause a device Reset.  2017-2019 Microchip Technology Inc. DS70005319D-page 309 dsPIC33CH128MP508 FAMILY 4.5 Slave Interrupt Controller Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “Interrupts” (www.microchip.com/ DS70000600) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). The dsPIC33CH128MP508S1 family interrupt controller reduces the numerous peripheral interrupt request signals to a single interrupt request signal to the dsPIC33CH128MP508S1 family CPU. The interrupt controller has the following features: • Six Processor Exceptions and Software Traps • Seven User-Selectable Priority Levels • Interrupt Vector Table (IVT) with a Unique Vector for each Interrupt or Exception Source • Fixed Priority within a Specified User Priority Level • Fixed Interrupt Entry and Return Latencies Note: There is no Alternate Interrupt Vector Table (AIVT) for the Slave. 4.5.1 The dsPIC33CH128MP508S1 family Interrupt Vector Table (IVT), shown in Figure 4-14, resides in program memory, starting at location, 000004h. The IVT contains six non-maskable trap vectors and up to 246 sources of interrupts. In general, each interrupt source has its own vector. Each interrupt vector contains a 24-bit wide address. The value programmed into each interrupt vector location is the starting address of the associated Interrupt Service Routine (ISR). Interrupt vectors are prioritized in terms of their natural priority. This priority is linked to their position in the vector table. Lower addresses generally have a higher natural priority. For example, the interrupt associated with Vector 0 takes priority over interrupts at any other vector address. 4.5.2 RESET SEQUENCE A device Reset is not a true exception because the interrupt controller is not involved in the Reset process. The dsPIC33CH128MP508S1 family devices clear their registers in response to a Reset, which forces the PC to zero. The device then begins program execution at location, 0x000000. A GOTO instruction at the Reset address can redirect program execution to the appropriate start-up routine. Note: DS70005319D-page 310 INTERRUPT VECTOR TABLE Any unimplemented or unused vector locations in the IVT should be programmed with the address of a default interrupt handler routine that contains a RESET instruction.  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY IVT Decreasing Natural Order Priority FIGURE 4-14: dsPIC33CH128MP508S1 FAMILY INTERRUPT VECTOR TABLE Reset – GOTO Instruction Reset – GOTO Address Oscillator Fail Trap Vector Address Error Trap Vector Generic Hard Trap Vector Stack Error Trap Vector Math Error Trap Vector Reserved Generic Soft Trap Vector Reserved Interrupt Vector 0 Interrupt Vector 1 : : : Interrupt Vector 52 Interrupt Vector 53 Interrupt Vector 54 : : : Interrupt Vector 116 Interrupt Vector 117 Interrupt Vector 118 Interrupt Vector 119 Interrupt Vector 120 : : : Interrupt Vector 244 Interrupt Vector 245 START OF CODE 0x000000 0x000002 0x000004 0x000006 0x000008 0x00000A 0x00000C 0x00000E 0x000010 0x000012 0x000014 0x000016 : : : 0x00007C 0x00007E 0x000080 : : : 0x0000FC 0x0000FE 0x000100 0x000102 0x000104 : : : 0x0001FC 0x0001FE 0x000200 See Table 4-21 for Interrupt Vector Details Note: In Dual Partition modes, each partition has a dedicated Interrupt Vector Table.  2017-2019 Microchip Technology Inc. DS70005319D-page 311 dsPIC33CH128MP508 FAMILY TABLE 4-20: TRAP TABLE Trap Description MPLAB® XC16 Vector Trap ISR # Name IVT Address Trap Bit Location Generic Flag Source Flag Enable Priority Level Oscillator Failure Trap _OscillatorFail 0 0x000004 INTCON1[1] — — 15 Address Error Trap _AddressError 1 0x000006 INTCON1[3] — — 14 Generic Hard Trap – ECCDBE _HardTrapError 2 0x000008 — INTCON4[1] — 13 Generic Hard Trap – SGHT 2 0x000008 — INTCON4[0] INTCON2[13] 13 — 12 _HardTrapError — Stack Error Trap _StackError 3 0x00000A INTCON1[2] Math Error Trap – OVAERR _MathError 4 0x00000C INTCON1[4] INTCON1[14] INTCON1[10] 11 Math Error Trap – OVBERR _MathError 4 0x00000C INTCON1[4] INTCON1[13] INTCON1[9] 11 Math Error Trap – COVAERR _MathError 4 0x00000C INTCON1[4] INTCON1[12] INTCON1[8] 11 Math Error Trap – COVBERR _MathError 4 0x00000C INTCON1[4] INTCON1[11] INTCON1[8] 11 Math Error Trap – SFTACERR _MathError 4 0x00000C INTCON1[4] INTCON1[7] INTCON1[8] 11 Math Error Trap – DIV0ERR _MathError 4 0x00000C INTCON1[4] INTCON1[6] INTCON1[8] 11 Reserved Reserved 5 0x00000E — — — — Generic Soft Trap – CAN _SoftTrapError 6 0x000010 — INTCON3[9] — 9 Generic Soft Trap – NAE _SoftTrapError 6 0x000010 — INTCON3[8] — 9 Generic Soft Trap – CAN2 _SoftTrapError 6 0x000010 — INTCON3[6] — 9 Generic Soft Trap – DAE _SoftTrapError 6 0x000010 — INTCON3[5] — 9 Generic Soft Trap – DOOVR _SoftTrapError 6 0x000010 — INTCON3[4] — 9 Generic Soft Trap – APLL Lock _SoftTrapError 6 0x000010 — INTCON3[0] — 9 Reserved 7 0x000012 — — — — DS70005319D-page 312 Reserved  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 4-21: SLAVE INTERRUPT VECTOR DETAILS(1) Interrupt Description MPLAB® XC16 ISR Name Vector # IRQ # IVT Address Interrupt Bit Location Flag Enable Priority External Interrupt 0 _INT0Interrupt 8 0 0x000014 IFS0[0] IEC0[0] IPC0[2:0] Timer1 _T1Interrupt 9 1 0x000016 IFS0[1] IEC0[1] IPC0[6:4] Change Notice Interrupt A _CNAInterrupt 10 2 0x000018 IFS0[2] IEC0[2] IPC0[10:8] Change Notice Interrupt B _CNBInterrupt 11 3 0x00001A IFS0[3] IEC0[3] IPC0[14:12] IPC1[2:0] DMA Channel 0 _DMA0Interrupt 12 4 0x00001C IFS0[4] IEC0[4] Reserved Reserved 13 5 0x00001E — — — Input Capture/Output Compare 1 _CCP1Interrupt 14 6 0x000020 IFS0[6] IEC0[6] IPC1[10:8] CCP1 Timer _CCT1Interrupt 15 7 0x000022 IFS0[7] IEC0[7] IPC1[14:12] DMA Channel 1 _DMA1Interrupt 16 8 0x000024 IFS0[8] IEC0[8] IPC2[2:0] SPI1 Receiver _SPI1RXInterrupt 17 9 0x000026 IFS0[9] IEC0[9] IPC2[6:4] SPI1 Transmitter _SPI1TXInterrupt 18 10 0x000028 IFS0[10] IEC0[10] IPC2[10:8] UART1 Receiver _U1RXInterrupt 19 11 0x00002A IFS0[11] IEC0[11] IPC2[14:12] UART1 Transmitter _U1TXInterrupt 20 12 0x00002C IFS0[12] IEC0[12] IPC3[2:0] ECC Single Bit Error _ECCSBEInterrupt 21 13 0x00002E IFS0[13] IEC0[13] IPC3[6:4] NVM Write Complete _NVMInterrupt 22 14 0x000030 IFS0[14] IEC0[14] IPC3[10:8] External Interrupt 1 _INT1Interrupt 23 15 0x000032 IFS0[15] IEC0[15] IPC3[14:12] I2C1 Slave Event _SI2C1Interrupt 24 16 0x000034 IFS1[0] IEC1[0] IPC4[2:0] I2C1 Master Event _MI2C1Interrupt 25 17 0x000036 IFS1[1] IEC1[1] IPC4[6:4] Reserved Reserved 26 18 0x000038 — — — Change Notice Interrupt C _CNCInterrupt 27 19 0x00003A IFS1[3] IEC1[3] IPC4[14:12] IPC5[2:0] External Interrupt 2 _INT2Interrupt Reserved Reserved 28 20 0x00003C IFS1[4] IEC1[4] 29-30 21-22 0x00003E-0x000040 — — — Input Capture/Output Compare 2 _CCP2Interrupt 31 23 0x000042 IFS1[7] IEC1[7] IPC5[14:12] CCP2 Timer _CCT2Interrupt 32 24 0x000044 IFS1[8] IEC1[8] IPC6[2:0] Reserved Reserved 33 25 0x000046 IFS1[9] IEC1[9] IPC6[6:4] External Interrupt 3 _INT3Interrupt IPC6[10:8] Reserved Reserved Input Capture/Output Compare 3 _CCP3Interrupt CCP3 Timer _CCT3Interrupt Reserved Reserved Input Capture/Output Compare 4 _CCP4Interrupt CCP4 Timer _CCT4Interrupt Reserved Reserved QEI Position Counter Compare _QEI1Interrupt UART1 Error _U1EInterrupt Reserved Reserved In-Circuit Debugger _ICDInterrupt Reserved Reserved I2C1 Bus Collision _I2C1BCInterrupt 34 26 0x000048 IFS1[10] IEC1[10] 35-42 27-34 0x00004A-0x000058 — — — 43 35 0x00005A IFS2[3] IEC2[3] IPC8[14:12] IPC9[2:0] 44 36 0x00005C IFS2[4] IEC2[4] 45-47 37-39 0x00005E-0x000062 — — — 48 40 0x000064 IFS2[8] IEC2[8] IPC10[2:0] IPC10[6:4] 49 41 0x000066 IFS2[9] IEC2[9] 50-55 42-47 0x000068-0x000072 — — — 56 48 0x000074 IFS3[0] IEC3[0] IPC12[2:0] IPC12[6:4] 57 49 0x000076 IFS3[1] IEC3[1] 58-68 50-60 0x000078-0x00008C — — — 69 61 0x00008E IFS3[13] IEC3[13] IPC15[6:4] 70-71 62-63 0x000090-0x000092 — — — 72 64 0x000094 IFS4[0] IEC4[0] IPC16[2:0] Reserved Reserved 73-74 65-66 0x000096-0x000098 — — — PWM Generator 1 _PWM1Interrupt 75 67 0x00009A IFS4[3] IEC4[3] IPC16[14:12] PWM Generator 2 _PWM2Interrupt 76 68 0x00009C IFS4[4] IEC4[4] IPC17[2:0] PWM Generator 3 _PWM3Interrupt 77 69 0x00009E IFS4[5] IEC4[5] IPC17[6:4] PWM Generator 4 _PWM4Interrupt 78 70 0x0000A0 IFS4[6] IEC4[6] IPC17[10:8] PWM Generator 5 _PWM5Interrupt 79 71 0x0000A2 IFS4[7] IEC4[7] IPC17[14:12] PWM Generator 6 _PWM6Interrupt 80 72 0x0000A4 IFS4[8] IEC4[8] IPC18[2:0] PWM Generator 7 _PWM7Interrupt 81 73 0x0000A6 IFS4[9] IEC4[9] IPC18[6:4] Note 1: Not all interrupts are available on all packages. Make sure the selected device variant has the interrupt available on the device.  2017-2019 Microchip Technology Inc. DS70005319D-page 313 dsPIC33CH128MP508 FAMILY TABLE 4-21: SLAVE INTERRUPT VECTOR DETAILS(1) (CONTINUED) Interrupt Description MPLAB® XC16 ISR Name Vector # IRQ # Interrupt Bit Location IVT Address Flag Enable Priority PWM Generator 8 _PWM8Interrupt 82 74 0x0000A8 IFS4[10] IEC4[10] IPC18[10:8] Change Notice D _CNDInterrupt 83 75 0x0000AA IFS4[11] IEC4[11] IPC18[14:12] Change Notice E _CNEInterrupt 84 76 0x0000AC IFS4[12] IEC4[12] IPC19[2:0] Reserved Reserved 85 77 0x0000AE — — — Slave Comparator 1 _CMP1Interrupt 86 78 0x0000B0 IFS4[14] IEC4[14] IPC19[10:8] Slave Comparator 2 _CMP2Interrupt 87 79 0x0000B2 IFS4[15] IEC4[15] IPC19[14:12] Slave Comparator 3 _CMP3Interrupt 88 80 0x0000B4 IFS5[0] IEC5[0] IPC20[2:0] Reserved Reserved 89 81 0x0000B6 — — — Master PTG Trigger 4 _PTG4Interrupt 90 82 0x0000B8 IFS5[2] IEC5[2] IPC20[10:8] Master PTG Trigger 5 _PTG5Interrupt 91 83 0x0000BA IFS5[3] IEC5[3] IPC20[14:12] Master PTG Trigger 6 _PTG6Interrupt 92 84 0x0000BC IFS5[4] IEC5[4] IPC21[2:0] Master PTG Trigger 7 _PTG7Interrupt 93 85 0x0000BE IFS5[5] IEC5[5] IPC21[6:4] Reserved Reserved 94-97 86-89 0x0000C0-0x0000C6 — — — ADC Global Interrupt _ADCInterrupt 98 90 0x0000C8 IFS5[10] IEC5[10] IPC22[10:8] ADC AN0 Interrupt _ADCAN0Interrupt 99 91 0x0000CA IFS5[11] IEC5[11] IPC22[14:12] IPC23[2:0] ADC AN1 Interrupt _ADCAN1Interrupt 100 92 0x0000CC IFS5[12] IEC5[12] ADC AN2 Interrupt _ADCAN2Interrupt 101 93 0x0000CE IFS5[13] IEC5[13] IPC23[6:4] ADC AN3 Interrupt _ADCAN3Interrupt 102 94 0x0000D0 IFS5[14] IEC5[14] IPC23[10:8] ADC AN4 Interrupt _ADCAN4Interrupt 103 95 0x0000D2 IFS5[15] IEC5[15] IPC23[14:12] ADC AN5 Interrupt _ADCAN5Interrupt 104 96 0x0000D4 IFS6[0] IEC6[0] IPC24[2:0] ADC AN6 Interrupt _ADCAN6Interrupt 105 97 0x0000D6 IFS6[1] IEC6[1] IPC24[6:4] ADC AN7 Interrupt _ADCAN7Interrupt 106 98 0x0000D8 IFS6[2] IEC6[2] IPC24[10:8] ADC AN8 Interrupt _ADCAN8Interrupt 107 99 0x0000DA IFS6[3] IEC6[3] IPC24[14:12] ADC AN9 Interrupt _ADCAN9Interrupt 108 100 0x0000DC IFS6[4] IEC6[4] IPC25[2:0] ADC AN10 Interrupt _ADCAN10Interrupt 109 101 0x0000DE IFS6[5] IEC6[5] IPC25[6:4] ADC AN11 Interrupt _ADCAN11Interrupt 110 102 0x0000E0 IFS6[6] IEC6[6] IPC25[10:8] ADC AN12 Interrupt _ADCAN12Interrupt 111 103 0x0000E2 IFS6[7] IEC6[7] IPC25[14:12] ADC AN13 Interrupt _ADCAN13Interrupt 112 104 0x0000E4 IFS6[8] IEC6[8] IPC26[2:0] ADC AN14 Interrupt _ADCAN14Interrupt 113 105 0x0000E6 IFS6[9] IEC6[9] IPC26[6:4] ADC AN15 Interrupt _ADCAN15Interrupt 114 106 0x0000E8 IFS6[10] IEC6[10] IPC26[10:8] ADC AN16 Interrupt _ADCAN16Interrupt 115 107 0x0000EA IFS6[11] IEC6[11] IPC26[14:12] ADC AN17 Interrupt _ADCAN17Interrupt 116 108 0x0000EC IFS6[12] IEC6[12] IPC27[2:0] ADC AN18 Interrupt _ADCAN18Interrupt 117 109 0x0000EE IFS6[13] IEC6[13] IPC27[6:4] ADC AN19 Interrupt _ADCAN19Interrupt 118 110 0x0000F0 IFS6[14] IEC6[14] IPC27[10:8] ADC AN20 Interrupt _ADCAN20Interrupt 119 111 0x0000F2 IFS6[15] IEC6[15] IPC27[14:12] Reserved Reserved ADC Fault _ADFLTInterrupt 120-122 112-114 0x0000F4-0x0000F8 123 — — — 115 0x0000FA IFS7[3] IEC7[3] IPC28[14:12] IPC29[2:0] ADC Digital Comparator 0 _ADCMP0Interrupt 124 116 0x0000FC IFS7[4] IEC7[4] ADC Digital Comparator 1 _ADCMP1Interrupt 125 117 0x0000FE IFS7[5] IEC7[5] IPC29[6:4] ADC Digital Comparator 2 _ADCMP2Interrupt 126 118 0x000100 IFS7[6] IEC7[6] IPC29[10:8] ADC Digital Comparator 3 _ADCMP3Interrupt 127 119 0x000102 IFS7[7] IEC7[7] IPC29[14:12] ADC Oversample Filter 0 _ADFLTR0Interrupt 128 120 0x000104 IFS7[8] IEC7[8] IPC30[2:0] ADC Oversample Filter 1 _ADFLTR1Interrupt 129 121 0x000106 IFS7[9] IEC7[9] IPC30[6:4] ADC Oversample Filter 2 _ADFLTR2Interrupt 130 122 0x000108 IFS7[10] IEC7[10] IPC30[10:8] ADC Oversample Filter 3 _ADFLTR3Interrupt 131 123 0x00010A IFS7[11] IEC7[11] IPC30[14:12] CLC1 Positive Edge _CLC1PInterrupt 132 124 0x00010C IFS7[12] IEC7[12] IPC31[2:0] CLC2 Positive Edge _CLC2PInterrupt 133 125 0x00010E IFS7[13] IEC7[13] IPC31[6:4] Note 1: Not all interrupts are available on all packages. Make sure the selected device variant has the interrupt available on the device. DS70005319D-page 314  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 4-21: SLAVE INTERRUPT VECTOR DETAILS(1) (CONTINUED) Interrupt Description MPLAB® XC16 ISR Name SPI1 Error _SPI1GInterrupt Reserved Reserved MSI Master Initiated Interrupt _MSIS1Interrupt Vector # IRQ # IVT Address 134 126 0x000110 135-136 127-128 0x000112-0x000114 137 129 0x000116 Interrupt Bit Location Flag Enable Priority IFS7[14] IEC7[14] IPC31[10:8] — — — IFS8[1] IEC8[1] IPC32[6:4] MSIA – MSI Protocol A _MSIAInterrupt 138 130 0x000118 IFS8[2] IEC8[2] IPC32[10:8] MSIB – MSI Protocol B _MSIBInterrupt 139 131 0x00011A IFS8[3] IEC8[3] IPC32[14:12] MSIC – MSI Protocol C _MSICInterrupt 140 132 0x00011C IFS8[4] IEC8[4] IPC33[2:0] MSID – MSI Protocol D _MSIDInterrupt 141 133 0x00011E IFS8[5] IEC8[5] IPC33[6:4] MSIE – MSI Protocol E _MSIEInterrupt 142 134 0x000120 IFS8[6] IEC8[6] IPC33[10:8] MSIF – MSI Protocol F _MSIFInterrupt 143 135 0x000122 IFS8[7] IEC8[7] IPC33[14:12] MSIG – MSI Protocol G _MSIGInterrupt 144 136 0x000124 IFS8[8] IEC8[8] IPC34[2:0] MSIH – MSI Protocol H _MSIHInterrupt 145 137 0x000126 IFS8[9] IEC8[9] IPC34[6:4] MSI Slave Read FIFO Data Ready _MSIDTInterrupt 146 138 0x000128 IFS8[10] IEC8[10] IPC34[10:8] MSI Slave Write FIFO Empty _MSIWFEInterrupt 147 139 0x00012A IFS8[11] IEC8[11] IPC34[14:12] Read or Write FIFO Fault (Over/Underflow) _MSIFLTInterrupt 148 140 0x00012C IFS8[12] IEC8[12] IPC35[2:0] 149 141 0x00012E IFS8[13] IEC8[13] IPC35[6:4] — — — IFS9[1] IEC9[1] IPC36[6:4] MSI Master Reset _MSTSRSTInterrupt Reserved Reserved Master Break _MSTBRKInterrupt Reserved Reserved Master Clock Fail _MCLKFInterrupt 150-152 142-144 0x000130-0x000136 153 145 0x000138 154-163 146-155 0x00013A-0x00014C 164 156 0x00014E 165-175 157-167 0x000150-0x000162 — — — IFS9[12] IEC9[12] IPC39[2:0] Reserved Reserved ADC FIFO Ready _ADFIFOInterrupt 176 168 0x000164 PWM Event A _PEVTAInterrupt 177 169 0x000166 IFS10[9] IEC10[9] IPC42[6:4] PWM Event B _PEVTBInterrupt 178 170 0x000168 IFS10[10] IEC10[10] IPC42[10:8] PWM Event C _PEVTCInterrupt 179 171 0x00016A IFS10[11] IEC10[11] IPC42[14:12] PWM Event D _PEVTDInterrupt 180 172 0x00016C IFS10[12] IEC10[12] IPC43[2:0] PWM Event E _PEVTEInterrupt 181 173 0x00016E IFS10[13] IEC10[13] IPC43[6:4] PWM Event F _PEVTFInterrupt 182 174 0x000170 IFS10[14] IEC10[14] IPC43[10:8] CLC3 Positive Edge _CLC3PInterrupt 183 175 0x000172 IFS10[15] IEC10[15] IPC43[14:12] CLC4 Positive Edge _CLC4PInterrupt 184 176 0x000174 IFS11[0] IEC11[0] IPC44[2:0] CLC1 Negative Edge _CLC1NInterrupt 185 177 0x000176 IFS11[1] IEC11[1] IPC44[6:4] CLC2 Negative Edge _CLC2NInterrupt 186 178 0x000178 IFS11[2] IEC11[2] IPC44[10:8] CLC3 Negative Edge _CLC3NInterrupt 187 179 0x00017A IFS11[3] IEC11[3] IPC44[14:] CLC4 Negative Edge _CLC4NInterrupt 188 180 0x00017C IFS11[4] IEC11[4] IPC45[2:0] Reserved Reserved UART1 Event _U1EVTInterrupt 189-196 181-188 0x0017E- 0x0018C 197 189 0x00018E — — — IFS10[8] IEC10[8] IPC42[2:0] — — — IFS11[13] IEC11[13] IPC47[6:4] Note 1: Not all interrupts are available on all packages. Make sure the selected device variant has the interrupt available on the device.  2017-2019 Microchip Technology Inc. DS70005319D-page 315 SLAVE INTERRUPT FLAG REGISTERS Register Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 IFS0 INT1IF NVMIF ECCSBEIF U1TXIF U1RXIF SPI1TXIF SPI1RXIF IFS1 — — — — — INT3IF — IFS2 — — — — — — IFS3 — — ICDIF — — — Bit 3 Bit 2 DMA1IF CCT1IF CCP1IF — CCT2IF CCP2IF — — CCT4IF CCP4IF — — — — — — Bit 1 Bit 0 DMA0IF CNBIF CNAIF T1IF INT0IF INT2IF CNCIF — MI2C1IF SI2C1IF — CCT3IF CCP3IF — — — — — — — U1EIF QEI1IF IFS4 CMP2IF CMP1IF — CNEIF CNDIF PWM8IF PWM7IF PWM6IF PWM5IF PWM4IF PWM3IF PWM2IF PWM1IF — — I2C1BCIF IFS5 ADCAN4IF ADCAN3IF ADCAN2IF ADCAN1IF ADCAN0IF ADCIF — — — — PTG7IF PTG6IF PTG5IF PTG4IF — CMP3IF IFS6 ADCAN20IF ADCAN19IF ADCAN18IF ADCAN17IF ADCAN16IF ADCAN15IF ADCAN14IF ADCAN13IF ADCAN12IF ADCAN11IF ADCAN10IF ADCAN9IF ADCAN8IF ADCAN7IF ADCAN6IF ADCAN5IF IFS7 — SPI1IF CLC2PIF CLC1PIF ADFLTR3IF ADFLTR2IF ADFLTR1IF ADFLTR0IF ADCMP3IF ADCMP2IF ADFLTIF — — — IFS8 — — MSIMRSTIF MSIFLTIF MSIWFEIF MSIDTIF MSIHIF MSIGIF MSIFIF MSIEIF MSIDIF MSICIF MSIBIF MSIAIF MSIMIF — IFS9 — — — MCLKFIF — — — — — — — — — — MSTBRKIF — IFS10 CLC3PIF PEVTFIF PEVTEIF PEVTDIF PEVTCIF PEVTBIF PEVTAIF ADFIFOIF — — — — — — — — IFS11 — — U1EVTIF — — — — — — — — CLC4NIF CLC3NIF CLC2NIF CLC1NIF CLC4PIF Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TABLE 4-23: ADCMP1IF ADCMP0IF SLAVE INTERRUPT ENABLE REGISTERS Register Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 IEC0 INT1IE NVMIE ECCSBEIE U1TXIE U1RXIE SPI1TXIE SPI1RXIE DMA1IE CCT1IE CCP1IE — DMA0IE CNBIE CNAIE T1IE INT0IE IEC1 — — — — — INT3IE — CCT2IE CCP2IE — — INT2IE CNCIE — MI2C1IE SI2C1IE IEC2 — — — — — — CCT4IE CCP4IE — — — CCT3IE CCP3IE — — — IEC3 — — ICDIE — — — — — — — — — — — U1EIE QEI1IE IEC4 CMP2IE CMP1IE — CNEIE CNDIE PWM8IE PWM7IE PWM6IE PWM5IE PWM4IE PWM3IE PWM2IE PWM1IE — — I2C1BCIE IEC5 ADCAN4IE ADCAN3IE ADCAN2IE ADCAN1IE ADCAN0IE ADCIE — — — — PTG7IE PTG6IE PTG5IE PTG4IE — CMP3IE IEC6 ADCAN20IE ADCAN19IE ADCAN18IE ADCAN17IE ADCAN16IE ADCAN15IE ADCAN14IE ADCAN13IE ADCAN12IE ADCAN11IE ADCAN10IE ADCAN9IE ADCAN8IE ADCAN7IE ADCAN6IE ADCAN5IE  2017-2019 Microchip Technology Inc. IEC7 — SPI1IE CLC2PIE CLC1PIE ADFLTR3IE ADFLTR2IE ADFLTR1IE ADFLTR0IE ADCMP3IE ADFLTIE — — — IEC8 — — MSIMRSTIE MSIFLTIE MSIWFEIE MSIDTIE MSIHIE MSIGIE MSIFIE MSIEIE MSIDIE MSICIE MSIBIE MSIAIE MSIMIF — IEC9 — — — MCLKFIE — — — — — — — — — — MSTBRKIE — IEC10 CLC3PIE PEVTFIE PEVTEIE PEVTDIE PEVTCIE PEVTBIE PEVTAIE ADFIFOIE — — — — — — — — IEC11 — — U1EVTIE — — — — — — — — CLC4NIE CLC3NIE CLC2NIE CLC1NIE CLC4PIE ADCMP2IE ADCMP1IE ADCMP0IE dsPIC33CH128MP508 FAMILY DS70005319D-page 316 TABLE 4-22:  2017-2019 Microchip Technology Inc. TABLE 4-24: Register Bit 15 SLAVE INTERRUPT PRIORITY REGISTERS Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 IPC0 — CNBIP2 CNBIP1 CNBIP0 — CNAIP2 CNAIP1 CNAIP0 — T1IP2 T1IP1 T1IP0 — INT0IP2 INT0IP1 INT0IP0 IPC1 — CCT1IP2 CCT1IP1 CCT1IP0 — CCP1IP2 CCP1IP1 CCP1IP0 — — — — — DMA0IP2 DMA0IP1 DMA0IP0 IPC2 — U1RXIP2 U1RXIP1 U1RXIP0 — SPI1TXIP2 SPI1TXIP1 SPI1TXIP0 — SPI1RXIP2 SPI1RXIP1 SPI1RXIP0 — DMA1IP2 DMA1IP1 DMA1IP0 IPC3 — INT1IP2 INT1IP1 INT1IP0 — NVMIP2 NVMIP1 NVMIP0 — ECCSBEIP2 ECCSBEIP1 ECCSBEIP0 — U1TXIP2 U1TXIP1 U1TXIP0 IPC4 — CNCIP2 CNCIP1 CNCIP0 — — — — — MI2C1IP2 MI2C1IP1 MI2C1IP0 — SI2C1IP2 SI2C1IP1 SI2C1IP0 IPC5 — CCP2IP2 CCP2IP1 CCP2IP0 — — — — — — — — — INT2IP2 INT2IP1 INT2IP0 IPC6 — — — — — INT3IP2 INT3IP1 INT3IP0 — — — — — CCT2IP2 CCT2IP1 CCT2IP0 IPC7 — — — — — — — — — — — — — — — — IPC8 — CCP3IP2 CCP3IP1 CCP3IP0 — — — — — — — — — — — — IPC9 — — — — — — — — — — — — — CCT3IP2 CCT3IP1 CCT3IP0 CCP4IP0 — — — — — — — — — CCT4IP2 CCT4IP1 CCT4IP0 — CCP4IP2 CCP4IP1 — — — — — — — — — — — — — — — — IPC12 — — — — — — — — — U1EIP2 U1EIP1 U1EIP0 — QEI1IP2 QEI1IP1 QEI1IP0 IPC13 — — — — — — — — — — — — — — — — IPC14 — — — — — — — — — — — — — — — — IPC15 — — — — — JTAGIP2 JTAGIP1 JTAGIP0 — ICDIP2 ICDIP1 ICDIP0 — — — — IPC16 — PWM1IP2 PWM1IP1 PWM1IP0 — — — — — — — — — I2C1BCIP2 I2C1BCIP1 I2C1BCIP0 IPC17 — PWM5IP2 PWM5IP1 PWM5IP0 — PWM4IP2 PWM4IP1 PWM4IP0 — PWM3IP2 PWM3IP1 PWM3IP0 — PWM2IP2 PWM2IP1 PWM2IP0 IPC18 — CNDIP2 CNDIP1 CNDIP0 — PWM8IP2 PWM8IP1 PWM8IP0 — PWM7IP2 PWM7IP1 PWM7IP0 — PWM6IP2 PWM6IP1 PWM6IP0 IPC19 — CMP2IP2 CMP2IP1 CMP2IP0 — CMP1IP2 CMP1IP1 CMP1IP0 — — — — — CNEIP2 CNEIP1 CNEIP0 IPC20 — PTG5IP2 PTG5IP1 PTG5IP0 — PTG4IP2 PTG4IP1 PTG4IP0 — — — — — CMP3IP2 CMP3IP1 CMP3IP0 IPC21 — — — — — — — — — PTG7IP2 PTG7IP1 PTG7IP0 — PTG6IP2 PTG6IP1 PTG6IP0 IPC22 — ADCAN0IP2 ADCAN0IP1 ADCAN0IP0 — ADCIP2 ADCIP1 ADCIP — — — — — — — — IPC23 — ADCAN4IP2 ADCAN4IP1 ADCAN4IP0 — ADCAN3IP2 ADCAN3IP1 ADCAN3IP0 — ADCAN2IP2 ADCAN2IP1 ADCAN2IP0 — ADCAN1IP2 ADCAN1IP1 ADCAN1IP0 IPC24 — ADCAN8IP2 ADCAN8IP1 ADCAN8IP0 — ADCAN7IP2 ADCAN7IP1 ADCAN7IP0 — ADCAN6IP2 ADCAN6IP1 ADCAN6IP0 — ADCAN5IP2 ADCAN5IP1 ADCAN5IP0 IPC25 — ADCAN12IP2 ADCAN12IP1 ADCAN12IP0 — ADCAN11IP2 ADCAN11IP1 ADCAN11IP0 — ADCAN10IP2 ADCAN10IP1 ADCAN10IP0 — ADCAN9IP2 ADCAN9IP1 ADCAN9IP0 IPC26 — ADCAN16IP2 ADCAN16IP1 ADCAN16IP0 — ADCAN15IP2 ADCAN15IP1 ADCAN15IP0 — ADCAN14IP2 ADCAN14IP1 ADCAN14IP0 — ADCAN13IP2 ADCAN13IP1 ADCAN13IP0 IPC27 — ADCAN20IP2 ADCAN20IP1 ADCAN20IP0 — ADCAN19IP2 ADCAN19IP1 ADCAN19IP0 — ADCAN18IP2 ADCAN18IP1 ADCAN18IP0 IPC28 — IPC29 — ADCMP3IP2 ADCMP3IP1 ADCMP3IP0 — ADCMP2IP2 ADCMP2IP1 ADCMP2IP0 — ADCMP1IP2 ADCMP1IP1 IPC30 — ADFLTR3IP2 ADFLTR3IP1 ADFLTR3IP0 — ADFLTR2IP2 ADFLTR2IP1 ADFLTR2IP0 IPC31 — — — — — SPI1IP2 SPI1IP1 IPC32 — MSIBIP2 MSIBIP1 MSIBIP0 — MSIAIP2 MSIAIP1 IPC33 — MSIFIP2 MSIFIP1 MSIFIP0 — MSIEIP2 MSIEIP1 IPC34 — MSIWFEIP2 MSIWFEIP1 MSIWFEIP0 — MSIDTIP2 IPC35 — — — — — — ADFLTIP2 ADFLTIP1 ADFLTIP0 — — — ADCAN17IP2 ADCAN17IP1 ADCAN17IP0 — — ADCAN21IP2 ADCAN21IP1 ADCAN21IP0 ADCMP1IP0 — ADCMP0IP2 — ADFLTR1IP2 ADFLTR1IP1 ADFLTR1IP0 — ADFLTR0IP2 ADFLTR0IP1 ADFLTR0IP0 SPI1IP0 — CLC2PEIP2 CLC2PEIP1 CLC2PEIP0 — CLC1PEIP2 CLC1PEIP1 MSIAIP0 — MSMIP2 MSMIP1 MSMIP0 — — — — MSIEIP0 — MSIDIP2 MSIDIP1 MSIDIP0 — MSICIP2 MSICIP1 MSICIP0 MSIDTIP1 MSIDTIP0 — MSIHIP2 MSIHIP1 MSIHIP0 — MSIGIP2 MSIGIP1 MSIGIP0 — — — — MSIFLTIP2 MSIFLTIP1 MSIFLTIP0 — — — — — MSIMRSTIP2 MSIMRSTIP1 MSIMRSTIP0 ADCMP0IP1 ADCMP0IP0 CLC1PEIP0 dsPIC33CH128MP508 FAMILY DS70005319D-page 317 IPC10 IPC11 Register SLAVE INTERRUPT PRIORITY REGISTERS (CONTINUED) Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 IPC36 — — — — — — — — — Bit 6 IPC37 — — — — — — — — — — IPC38 — — — — — — — — — IPC39 — — — — — — — — Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 MSTBRKIP0 — — — — — — — — — — — — — — — — — — — — — — MCLKFIP2 MCLKFIP1 MCLKFIP0 ADC0IP0 MSTBRKIP2 MSTBRKIP1 IPC40 — — — — — — — — — ADC1IP2 ADC1IP1 ADC1IP0 — ADC0IP2 ADC0IP1 IPC41 — — — — — — — — — — — — — — — — IPC42 — PEVTCIP2 PEVTCIP1 PEVTCIP0 — PEVTBIP2 PEVTBIP1 PEVTBIP0 — PEVTAIP2 PEVTAIP1 PEVTAIP0 — ADFIFOIP2 ADFIFOIP1 ADFIFOIP0 IPC43 — CLC3PIP2 CLC3PIP1 CLC3PIP0 — PEVTFIP2 PEVTFIP1 PEVTFIP0 — PEVTEIP2 PEVTEIP1 PEVTEIP0 — PEVTDIP2 PEVTDIP1 PEVTDIP0 IPC44 — CLC3NIP2 CLC3NIP1 CLC3NIP0 — CLC2NIP2 CLC2NIP1 CLC2NIP0 — CLC1NIP2 CLC1NIP1 CLC1NIP0 — CLC4PIP2 CLC4PIP1 CLC4PIP0 IPC45 — — — — — — — — — — — — — CLC4NIP2 CLC4NIP1 CLC4NIP0 IPC46 — — — — — — — — — — — — — — — — IPC47 — — — — — — — — — U1EVTIP2 U1EVTIP1 U1EVTIP0 — — — — dsPIC33CH128MP508 FAMILY DS70005319D-page 318 TABLE 4-24:  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 4.5.3 INTERRUPT RESOURCES 4.5.4.4 IPCx Many useful resources are provided on the main product page of the Microchip website for the devices listed in this data sheet. This product page contains the latest updates and additional information. The IPCx registers are used to set the Interrupt Priority Level (IPL) for each source of interrupt. Each user interrupt source can be assigned to one of seven priority levels. 4.5.3.1 4.5.5 Key Resources • “Interrupts” (www.microchip.com/DS70000600) in the “dsPIC33/PIC24 Family Reference Manual” • Code Samples • Application Notes • Software Libraries • Webinars • All Related “dsPIC33/PIC24 Family Reference Manual” Sections • Development Tools 4.5.4 INTERRUPT CONTROL AND STATUS REGISTERS The dsPIC33CH128MP508S1 family devices implement the following registers for the interrupt controller: • • • • • INTCON1 INTCON2 INTCON3 INTCON4 INTTREG 4.5.4.1 INTCON1 through INTCON4 Global interrupt control functions are controlled from INTCON1, INTCON2, INTCON3 and INTCON4. INTCON1 contains the Interrupt Nesting Disable bit (NSTDIS), as well as the control and status flags for the processor trap sources. The INTCON2 register controls external interrupt request signal behavior and contains the Global Interrupt Enable bit (GIE). INTCON3 contains the status flags for the Auxiliary PLL and DO stack overflow status trap sources. The INTCON4 register contains the Generated Hard Trap Status bit (SGHT). 4.5.4.2 Software IFSx The IFSx registers maintain all of the interrupt request flags. Each source of interrupt has a status bit, which is set by the respective peripherals or external signal and is cleared via software. 4.5.4.3 IECx The IECx registers maintain all of the interrupt enable bits. These control bits are used to individually enable interrupts from the peripherals or external signals.  2017-2019 Microchip Technology Inc. INTTREG The INTTREG register contains the associated interrupt vector number and the new CPU Interrupt Priority Level, which are latched into the Vector Number (VECNUM[7:0]) and Interrupt Level bits (ILR[3:0]) fields in the INTTREG register. The new Interrupt Priority Level is the priority of the pending interrupt. The interrupt sources are assigned to the IFSx, IECx and IPCx registers in the same sequence as they are listed in Table 4-21. For example, INT0 (External Interrupt 0) is shown as having Vector Number 8 and a natural order priority of 0. Thus, the INT0IF bit is found in IFS0[0], the INT0IE bit in IEC0[0] and the INT0IP[2:0] bits in the first position of IPC0 (IPC0[2:0]). 4.5.6 STATUS/CONTROL REGISTERS Although these registers are not specifically part of the interrupt control hardware, two of the CPU Control registers contain bits that control interrupt functionality. For more information on these registers, refer to “Enhanced CPU” (www.microchip.com/DS70005158) in the “dsPIC33/PIC24 Family Reference Manual”. • The CPU STATUS Register, SR, contains the IPL[2:0] bits (SR[7:5]). These bits indicate the current CPU Interrupt Priority Level. The user software can change the current CPU Interrupt Priority Level by writing to the IPLx bits. • The CORCON register contains the IPL3 bit which, together with IPL[2:0], also indicates the current CPU priority level. IPL3 is a read-only bit so that trap events cannot be masked by the user software. All Interrupt registers are described in Register 4-19 through Register 4-23 on the following pages. 4.5.7 CROSS CORE INTERRUPTS There are three interrupts that can occur in the Slave core based on the Master events: • MSIMRSTIF is a Master Reset interrupt which gets set in the Slave if the Master gets a Reset. This interrupt is enabled only when the MRTSIE bit (SI1CON[7]) is set • MCLKIF is a Slave interrupt which gets set if the Master core loses its system clock. • MSTBRKIF is the Master Break interrupt. This interrupt gets set in the Slave if the Master stops at a breakpoint (valid only when the Master is being debugged). DS70005319D-page 319 dsPIC33CH128MP508 FAMILY 4.5.8 SLAVE INTERRUPT CONTROL/STATUS REGISTERS SR: CPU STATUS REGISTER(1) REGISTER 4-17: R/W-0 R/W-0 R/W-0 R/W-0 R/C-0 R/C-0 R-0 R/W-0 OA OB SA SB OAB SAB DA DC bit 15 bit 8 R/W-0(3) IPL2 R/W-0(3) (2) IPL1 (2) R/W-0(3) R-0 R/W-0 R/W-0 R/W-0 R/W-0 IPL0(2) RA N OV Z C bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’= Bit is set ‘0’ = Bit is cleared x = Bit is unknown IPL[2:0]: CPU Interrupt Priority Level Status bits(2,3) 111 = CPU Interrupt Priority Level is 7 (15); user interrupts are disabled 110 = CPU Interrupt Priority Level is 6 (14) 101 = CPU Interrupt Priority Level is 5 (13) 100 = CPU Interrupt Priority Level is 4 (12) 011 = CPU Interrupt Priority Level is 3 (11) 010 = CPU Interrupt Priority Level is 2 (10) 001 = CPU Interrupt Priority Level is 1 (9) 000 = CPU Interrupt Priority Level is 0 (8) bit 7-5 Note 1: 2: 3: For complete register details, see Register 4-1. The IPL[2:0] bits are concatenated with the IPL[3] bit (CORCON[3]) to form the CPU Interrupt Priority Level. The value in parentheses indicates the IPL, if IPL[3] = 1. User interrupts are disabled when IPL[3] = 1. The IPL[2:0] Status bits are read-only when the NSTDIS bit (INTCON1[15]) = 1. DS70005319D-page 320  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-18: CORCON: SLAVE CORE CONTROL REGISTER(1) R/W-0 U-0 R/W-0 R/W-0 R/W-0 R-0 R-0 R-0 VAR — US1 US0 EDT DL2 DL1 DL0 bit 15 bit 8 R/W-0 R/W-0 R/W-1 R/W-0 R/C-0 R-0 R/W-0 R/W-0 SATA SATB SATDW ACCSAT IPL3(2) SFA RND IF bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’= Bit is set ‘0’ = Bit is cleared bit 15 VAR: Variable Exception Processing Latency Control bit 1 = Variable exception processing is enabled 0 = Fixed exception processing is enabled bit 3 IPL3: CPU Interrupt Priority Level Status bit 3(2) 1 = CPU Interrupt Priority Level is greater than 7 0 = CPU Interrupt Priority Level is 7 or less Note 1: 2: x = Bit is unknown For complete register details, see Register 4-2. The IPL3 bit is concatenated with the IPL[2:0] bits (SR[7:5]) to form the CPU Interrupt Priority Level.  2017-2019 Microchip Technology Inc. DS70005319D-page 321 dsPIC33CH128MP508 FAMILY REGISTER 4-19: INTCON1: SLAVE INTERRUPT CONTROL REGISTER 1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 NSTDIS OVAERR OVBERR COVAERR COVBERR OVATE OVBTE COVTE bit 15 bit 8 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 SFTACERR DIV0ERR — MATHERR ADDRERR STKERR OSCFAIL — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 NSTDIS: Interrupt Nesting Disable bit 1 = Interrupt nesting is disabled 0 = Interrupt nesting is enabled bit 14 OVAERR: Accumulator A Overflow Trap Flag bit 1 = Trap was caused by overflow of Accumulator A 0 = Trap was not caused by overflow of Accumulator A bit 13 OVBERR: Accumulator B Overflow Trap Flag bit 1 = Trap was caused by overflow of Accumulator B 0 = Trap was not caused by overflow of Accumulator B bit 12 COVAERR: Accumulator A Catastrophic Overflow Trap Flag bit 1 = Trap was caused by catastrophic overflow of Accumulator A 0 = Trap was not caused by catastrophic overflow of Accumulator A bit 11 COVBERR: Accumulator B Catastrophic Overflow Trap Flag bit 1 = Trap was caused by catastrophic overflow of Accumulator B 0 = Trap was not caused by catastrophic overflow of Accumulator B bit 10 OVATE: Accumulator A Overflow Trap Enable bit 1 = Trap overflow of Accumulator A 0 = Trap is disabled bit 9 OVBTE: Accumulator B Overflow Trap Enable bit 1 = Trap overflow of Accumulator B 0 = Trap is disabled bit 8 COVTE: Catastrophic Overflow Trap Enable bit 1 = Trap on catastrophic overflow of Accumulator A or B is enabled 0 = Trap is disabled bit 7 SFTACERR: Shift Accumulator Error Status bit 1 = Math error trap was caused by an invalid accumulator shift 0 = Math error trap was not caused by an invalid accumulator shift bit 6 DIV0ERR: Divide-by-Zero Error Status bit 1 = Math error trap was caused by a divide-by-zero 0 = Math error trap was not caused by a divide-by-zero bit 5 Unimplemented: Read as ‘0’ bit 4 MATHERR: Math Error Status bit 1 = Math error trap has occurred 0 = Math error trap has not occurred bit 3 ADDRERR: Address Error Trap Status bit 1 = Address error trap has occurred 0 = Address error trap has not occurred DS70005319D-page 322  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-19: INTCON1: SLAVE INTERRUPT CONTROL REGISTER 1 (CONTINUED) bit 2 STKERR: Stack Error Trap Status bit 1 = Stack error trap has occurred 0 = Stack error trap has not occurred bit 1 OSCFAIL: Oscillator Failure Trap Status bit 1 = Oscillator failure trap has occurred 0 = Oscillator failure trap has not occurred bit 0 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. DS70005319D-page 323 dsPIC33CH128MP508 FAMILY REGISTER 4-20: INTCON2: SLAVE INTERRUPT CONTROL REGISTER 2 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0 GIE DISI SWTRAP — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — — INT3EP INT2EP INT1EP INT0EP bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 GIE: Global Interrupt Enable bit 1 = Interrupts and associated IE bits are enabled 0 = Interrupts are disabled, but traps are still enabled bit 14 DISI: DISI Instruction Status bit 1 = DISI instruction is active 0 = DISI instruction is not active bit 13 SWTRAP: Software Trap Status bit 1 = Software trap is enabled 0 = Software trap is disabled bit 12-4 Unimplemented: Read as ‘0’ bit 3 INT3EP: External Interrupt 3 Edge Detect Polarity Select bit 1 = Interrupt on negative edge 0 = Interrupt on positive edge bit 2 INT2EP: External Interrupt 2 Edge Detect Polarity Select bit 1 = Interrupt on negative edge 0 = Interrupt on positive edge bit 1 INT1EP: External Interrupt 1 Edge Detect Polarity Select bit 1 = Interrupt on negative edge 0 = Interrupt on positive edge bit 0 INT0EP: External Interrupt 0 Edge Detect Polarity Select bit 1 = Interrupt on negative edge 0 = Interrupt on positive edge DS70005319D-page 324 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-21: INTCON3: SLAVE INTERRUPT CONTROL REGISTER 3 U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — — NAE bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 U-0 U-0 U-0 R/W-0 — — DAE DOOVR — — — APLL bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-9 Unimplemented: Read as ‘0’ bit 8 NAE: NVM Address Error Soft Trap Status bit 1 = NVM address error soft trap has occurred 0 = NVM address error soft trap has not occurred bit 7-6 Unimplemented: Read as ‘0’ bit 5 DAE: DMA Address Error (Soft) Trap Status bit 1 = DMA address error trap has occurred 0 = DMA address error trap has not occurred bit 4 DOOVR: DO Stack Overflow Soft Trap Status bit 1 = DO stack overflow soft trap has occurred 0 = DO stack overflow soft trap has not occurred bit 3-1 Unimplemented: Read as ‘0’ bit 0 APLL: Auxiliary PLL Loss of Lock Soft Trap Status bit 1 = APLL lock soft trap has occurred 0 = APLL lock soft trap has not occurred REGISTER 4-22: x = Bit is unknown INTCON4: SLAVE INTERRUPT CONTROL REGISTER 4 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — — SGHT bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-1 Unimplemented: Read as ‘0’ bit 0 SGHT: Software Generated Hard Trap Status bit 1 = Software generated hard trap has occurred 0 = Software generated hard trap has not occurred  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 325 dsPIC33CH128MP508 FAMILY REGISTER 4-23: INTTREG: SLAVE INTERRUPT CONTROL AND STATUS REGISTER U-0 U-0 R-0 U-0 R-0 R-0 R-0 R-0 — — VHOLD — ILR3 ILR2 ILR1 ILR0 bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 VECNUM[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 VHOLD: Vector Number Capture Enable bit 1 = VECNUM[7:0] bits read current value of vector number encoding tree (i.e., highest priority pending interrupt) 0 = Vector number latched into VECNUM[7:0] at Interrupt Acknowledge and retained until next IACK bit 12 Unimplemented: Read as ‘0’ bit 11-8 ILR[3:0]: New CPU Interrupt Priority Level bits 1111 = CPU Interrupt Priority Level is 15 ... 0001 = CPU Interrupt Priority Level is 1 0000 = CPU Interrupt Priority Level is 0 bit 7-0 VECNUM[7:0]: Vector Number of Pending Interrupt bits 11111111 = 255, Reserved; do not use ... 00001001 = 9, IC1 – Input Capture 1 00001000 = 8, INT0 – External Interrupt 0 00000111 = 7, Reserved; do not use 00000110 = 6, Generic soft error trap 00000101 = 5, Reserved; do not use 00000100 = 4, Math error trap 00000011 = 3, Stack error trap 00000010 = 2, Generic hard trap 00000001 = 1, Address error trap 00000000 = 0, Oscillator fail trap DS70005319D-page 326  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 4.6 Slave I/O Ports Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “I/O Ports with Edge Detect” (www.microchip.com/DS70005322) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). 2: The I/O ports are shared by the Master core and Slave core. All input goes to both the Master and Slave. The I/O ownership is defined by the Configuration bits. 3: The TMS pin function may be active multiple times during ICSP™ device erase, programming and debugging. When the TMS function is active, the integrated pull-up resistor will pull the pin to VDD. Proper care should be taken if there are sensitive circuits connected on the TMS pin during programming/erase and debugging. Many of the device pins are shared among the peripherals and the Parallel I/O ports. All I/O input ports feature Schmitt Trigger inputs for improved noise immunity. The Master and the Slave have the same number of I/O ports and are shared. The Master PORT registers are located in the Master SFR and the Slave PORT registers are located in the Slave SFR, respectively. All of the input goes to both Master and Slave. For example, a high in RA0 can be read as high on both Master and Slave as long as the TRISA0 bit is maintained as an input of both Master and Slave. The ownership of the output functionality is assigned by the Configuration registers, FCFGPRA0 to FCFGPRE0. Setting the bits in the FCFGPRA0 to FCFGPRE0 registers assigns ownership to the Master or Slave pin.  2017-2019 Microchip Technology Inc. 4.6.1 PARALLEL I/O (PIO) PORTS Generally, a Parallel I/O port that shares a pin with a peripheral is subservient to the peripheral. The peripheral’s output buffer data and control signals are provided to a pair of multiplexers. The multiplexers select whether the peripheral or the associated port has ownership of the output data and control signals of the I/O pin. The logic also prevents “loop through”, in which a port’s digital output can drive the input of a peripheral that shares the same pin. Figure 4-15 illustrates how ports are shared with other peripherals and the associated I/O pin to which they are connected. When a peripheral is enabled and the peripheral is actively driving an associated pin, the use of the pin as a general purpose output pin is disabled. The I/O pin can be read, but the output driver for the parallel port bit is disabled. If a peripheral is enabled, but the peripheral is not actively driving a pin, that pin can be driven by a port. All port pins have twelve registers directly associated with their operation as digital I/Os. The Data Direction register (TRISx) determines whether the pin is an input or an output. If the data direction bit is a ‘1’, then the pin is an input. All port pins are defined as inputs after a Reset. Reads from the latch (LATx), read the latch. Writes to the latch, write the latch. Reads from the port (PORTx), read the port pins, while writes to the port pins, write the latch. Any bit and its associated data and control registers that are not valid for a particular device are disabled. This means the corresponding LATx and TRISx registers, and the port pin are read as zeros. When a pin is shared with another peripheral or function that is defined as an input only, it is nevertheless regarded as a dedicated port because there is no other competing source of outputs. Table 4-25 shows the pin availability. Table 3-29 shows the 5V input tolerant pins across this device. DS70005319D-page 327 dsPIC33CH128MP508 FAMILY TABLE 4-25: PIN AND ANSELx AVAILABILITY Device Rx15 Rx14 Rx13 Rx12 Rx11 Rx10 Rx9 Rx8 Rx7 Rx6 Rx5 Rx4 Rx3 Rx2 Rx1 Rx0 PORTA dsPIC33XXXMP508/208 — — — — — — — — — — — X X X X X dsPIC33XXXMP506/206 — — — — — — — — — — — X X X X X dsPIC33XXXMP505/205 — — — — — — — — — — — X X X X X dsPIC33XXXMP503/203 — — — — — — — — — — — X X X X X dsPIC33XXXMP502/202 — — — — — — — — — — — X X X X X ANSELA — — — — — — — — — — — X X X X — dsPIC33XXXMP508/208 X X X X X X X X X X X X X X X X dsPIC33XXXMP506/206 X X X X X X X X X X X X X X X X dsPIC33XXXMP505/205 X X X X X X X X X X X X X X X X dsPIC33XXXMP503/203 X X X X X X X X X X X X X X X X dsPIC33XXXMP502/202 X X X X X X X X X X X X X X X X ANSELB — — — — — — — X X — — X X X X X PORTB PORTC dsPIC33XXXMP508/208 X X X X X X X X X X X X X X X X dsPIC33XXXMP506/206 X X X X X X X X X X X X X X X X dsPIC33XXXMP505/205 — — X X X X X X X X X X X X X X dsPIC33XXXMP503/203 — — — — — — — — — — X X X X X X dsPIC33XXXMP502/202 — — — — — — — — — — — — — — — — ANSELC — — — — — — — — X X — — X X X X X X X X X X X X X X PORTD dsPIC33XXXMP508/208 X X X X X X dsPIC33XXXMP506/206 X X X X X X X X X X X X X X X X dsPIC33XXXMP505/205 — — X — — X — X — — — — — — X — dsPIC33XXXMP503/203 — — — — — — — — — — — — — — — — dsPIC33XXXMP502/202 — — — — — — — — — — — — — — — — ANSELD — X X X X X — — — — — — — — — — PORTE dsPIC33XXXMP508/208 X X X X X X X X X X X X X X X X dsPIC33XXXMP506/206 — — — — — — — — — — — — — — — — dsPIC33XXXMP505/205 — — — — — — — — — — — — — — — — dsPIC33XXXMP503/203 — — — — — — — — — — — — — — — — dsPIC33XXXMP502/202 — — — — — — — — — — — — — — — — ANSELE — — — — — — — — — X — — — — — — DS70005319D-page 328  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 4-15: BLOCK DIAGRAM OF A TYPICAL SHARED PORT STRUCTURE Peripheral Module Output Multiplexers Peripheral Input Data Peripheral Module Enable Peripheral Output Enable Peripheral Output Data PIO Module WR TRISx Output Enable 0 1 Output Data 0 Read TRISx Data Bus I/O 1 D Q I/O Pin CK TRISx Latch D WR LATx + WR PORTx Q CK Data Latch Read LATx Input Data Read PORTx  2017-2019 Microchip Technology Inc. DS70005319D-page 329 dsPIC33CH128MP508 FAMILY 4.6.1.1 Open-Drain Configuration In addition to the PORTx, LATx and TRISx registers for data control, port pins can also be individually configured for either digital or open-drain output. This is controlled by the Open-Drain Control x register, ODCx, associated with each port. Setting any of the bits configures the corresponding pin to act as an open-drain output. The open-drain feature allows the generation of outputs, other than VDD, by using external pull-up resistors. The maximum open-drain voltage allowed on any pin is the same as the maximum VIH specification for that particular pin. If the TRISx bit is cleared (output) while the ANSELx bit is set, the digital output level (VOH or VOL) is converted by an analog peripheral, such as the ADC module or comparator module. When the PORTx register is read, all pins configured as analog input channels are read as cleared (a low level). Pins configured as digital inputs do not convert an analog input. Analog levels on any pin, defined as a digital input (including the ANx pins), can cause the input buffer to consume current that exceeds the device specifications. 4.6.2.1 I/O Port Write/Read Timing See the “Pin Diagrams” section for the available 5V tolerant pins and Table 24-18 for the maximum VIH specification for each pin. One instruction cycle is required between a port direction change or port write operation and a read operation of the same port. Typically, this instruction would be a NOP, as shown in Example 4-3. 4.6.2 The following registers are in the PORT module: CONFIGURING ANALOG AND DIGITAL PORT PINS The ANSELx register controls the operation of the analog port pins. The port pins that are to function as analog inputs or outputs must have their corresponding ANSELx and TRISx bits set. In order to use port pins for I/O functionality with digital modules, such as timers, UARTs, etc., the corresponding ANSELx bit must be cleared. The ANSELx register has a default value of 0xFFFF; therefore, all pins that share analog functions are analog (not digital) by default. Pins with analog functions affected by the ANSELx registers are listed with a buffer type of analog in the Pinout I/O Descriptions (see Table 1-1). DS70005319D-page 330 • • • • • • • • • • • • Register 4-24: ANSELx (one per port) Register 4-25: TRISx (one per port) Register 4-26: PORTx (one per port) Register 4-27: LATx (one per port) Register 4-28: ODCx (one per port) Register 4-29: CNPUx (one per port) Register 4-30: CNPDx (one per port) Register 4-31: CNCONx (one per port – optional) Register 4-32: CNEN0x (one per port) Register 4-33: CNSTATx (one per port – optional) Register 4-34: CNEN1x (one per port) Register 4-35: CNFx (one per port)  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 4.6.3 SLAVE PORT CONTROL/STATUS REGISTERS REGISTER 4-24: R/W-1 ANSELx: ANALOG SELECT FOR PORTx REGISTER R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 ANSELx[15:8] bit 15 bit 8 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 ANSELx[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown ANSELx[15:0]: Analog Select for PORTx bits 1 = Analog input is enabled and digital input is disabled on PORTx[n] pin 0 = Analog input is disabled and digital input is enabled on PORTx[n] pin  2017-2019 Microchip Technology Inc. DS70005319D-page 331 dsPIC33CH128MP508 FAMILY REGISTER 4-25: R/W-1 TRISx: OUTPUT ENABLE FOR PORTx REGISTER R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 TRISx[15:8] bit 15 bit 8 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 TRISx[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown TRISx[15:0]: Output Enable for PORTx bits 1 = LATx[n] is not driven on PORTx[n] pin 0 = LATx[n] is driven on PORTx[n] pin REGISTER 4-26: R/W-1 PORTx: INPUT DATA FOR PORTx REGISTER R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 PORTx[15:8] bit 15 bit 8 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 PORTx[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown PORTx[15:0]: PORTx Data Input Value bits DS70005319D-page 332  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-27: R/W-x LATx: OUTPUT DATA FOR PORTx REGISTER R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x LATx[15:8] bit 15 bit 8 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x LATx[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown LATx[15:0]: PORTx Data Output Value bits REGISTER 4-28: R/W-0 ODCx: OPEN-DRAIN ENABLE FOR PORTx REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ODCx[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ODCx[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown ODCx[15:0]: PORTx Open-Drain Enable bits 1 = Open-drain is enabled on PORTx pin 0 = Open-drain is disabled on PORTx pin  2017-2019 Microchip Technology Inc. DS70005319D-page 333 dsPIC33CH128MP508 FAMILY REGISTER 4-29: R/W-0 CNPUx: CHANGE NOTIFICATION PULL-UP ENABLE FOR PORTx REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CNPUx[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CNPUx[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown CNPUx[15:0]: Change Notification Pull-up Enable for PORTx bits 1 = The pull-up for PORTx[n] is enabled – takes precedence over pull-down selection 0 = The pull-up for PORTx[n] is disabled REGISTER 4-30: R/W-0 CNPDx: CHANGE NOTIFICATION PULL-DOWN ENABLE FOR PORTx REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CNPDx[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CNPDx[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown CNPDx[15:0]: Change Notification Pull-Down Enable for PORTx bits 1 = The pull-down for PORTx[n] is enabled (if the pull-up for PORTx[n] is not enabled) 0 = The pull-down for PORTx[n] is disabled DS70005319D-page 334  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-31: CNCONx: CHANGE NOTIFICATION CONTROL FOR PORTx REGISTER R/W-0 U-0 U-0 U-0 R/W-0 U-0 U-0 U-0 ON — — — CNSTYLE — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ON: Change Notification (CN) Control for PORTx On bit 1 = CN is enabled 0 = CN is disabled bit 14-12 Unimplemented: Read as ‘0’ bit 11 CNSTYLE: Change Notification Style Selection bit 1 = Edge style (detects edge transitions, CNFx[15:0] bits are used for a Change Notification event) 0 = Mismatch style (detects change from last port read, CNSTATx[15:0] bits are used for a Change Notification event) bit 10-0 Unimplemented: Read as ‘0’ REGISTER 4-32: R/W-0 CNEN0x: INTERRUPT CHANGE NOTIFICATION ENABLE FOR PORTx REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CNEN0x[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CNEN0x[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown CNEN0x[15:0]: Interrupt Change Notification Enable for PORTx bits 1 = Interrupt-on-change (from the last read value) is enabled for PORTx[n] 0 = Interrupt-on-change is disabled for PORTx[n]  2017-2019 Microchip Technology Inc. DS70005319D-page 335 dsPIC33CH128MP508 FAMILY REGISTER 4-33: R-0 CNSTATx: INTERRUPT CHANGE NOTIFICATION STATUS FOR PORTx REGISTER R-0 R-0 R-0 R-0 R-0 R-0 R-0 CNSTATx[15:8] bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 CNSTATx[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown CNSTAT[15:0]: Interrupt Change Notification Status for PORTx bits When CNSTYLE (CNCONx[11]) = 0: 1 = Change occurred on PORTx[n] since last read of PORTx[n] 0 = Change did not occur on PORTx[n] since last read of PORTx[n] REGISTER 4-34: R/W-0 CNEN1x: INTERRUPT CHANGE NOTIFICATION EDGE SELECT FOR PORTx REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CNEN1x[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CNEN1x[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown CNEN1x[15:0]: Interrupt Change Notification Edge Select for PORTx bits DS70005319D-page 336  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-35: R/W-0 CNFx: INTERRUPT CHANGE NOTIFICATION FLAG FOR PORTx REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CNFx[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CNFx[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown CNFx[15:0]: Interrupt Change Notification Flag for PORTx bits When CNSTYLE (CNCONx[11]) = 1: 1 = An enabled edge event occurred on PORTx[n] pin 0 = An enabled edge event did not occur on PORTx[n] pin  2017-2019 Microchip Technology Inc. DS70005319D-page 337 dsPIC33CH128MP508 FAMILY 4.6.4 INPUT CHANGE NOTIFICATION (ICN) The Input Change Notification function of the I/O ports allows the dsPIC33CH128MP508S1 family devices to generate interrupt requests to the processor in response to a Change-of-State (COS) on selected input pins. This feature can detect input Change-ofStates, even in Sleep mode, when the clocks are disabled. Every I/O port pin can be selected (enabled) for generating an interrupt request on a Change-ofState. Five control registers are associated with the Change Notification (CN) functionality of each I/O port. To enable the Change Notification feature for the port, the ON bit (CNCONx[15]) must be set. The CNEN0x and CNEN1x registers contain the CN interrupt enable control bits for each of the input pins. The setting of these bits enables a CN interrupt for the corresponding pins. Also, these bits, in combination with the CNSTYLE bit (CNCONx[11]), define a type of transition when the interrupt is generated. Possible CN event options are listed in Table 4-26. The CNSTATx register indicates whether a change occurred on the corresponding pin since the last read of the PORTx bit. In addition to the CNSTATx register, the CNFx register is implemented for each port. This register contains flags for Change Notification events. These flags are set if the valid transition edge, selected in the CNEN0x and CNEN1x registers, is detected. CNFx stores the occurrence of the event. CNFx bits must be cleared in software to get the next Change Notification interrupt. The CN interrupt is generated only for the I/Os configured as inputs (corresponding TRISx bits must be set). DS70005319D-page 338 TABLE 4-26: CNSTYLE Bit (CNCONx[11]) CHANGE NOTIFICATION EVENT OPTIONS CNEN1x CNEN0x Bit Bit Change Notification Event Description 0 Does not matter 0 Disabled 0 Does not matter 1 Detects a mismatch between the last read state and the current state of the pin 1 0 0 Disabled 1 0 1 Detects a positive transition only (from ‘0’ to ‘1’) 1 1 0 Detects a negative transition only (from ‘1’ to ‘0’) 1 1 1 Detects both positive and negative transitions Note: Pull-ups and pull-downs on Input Change Notification pins should always be disabled when the port pin is configured as a digital output. EXAMPLE 4-3: PORT WRITE/READ EXAMPLE MOV 0xFF00, W0 MOV W0, TRISB NOP BTSS PORTB, #13 ; ; ; ; ; ; Configure PORTB as inputs and PORTB as outputs Delay 1 cycle Next Instruction  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 4.6.5 PERIPHERAL PIN SELECT (PPS) A major challenge in general purpose devices is providing the largest possible set of peripheral features, while minimizing the conflict of features on I/O pins. The challenge is even greater on low pin count devices. In an application where more than one peripheral needs to be assigned to a single pin, inconvenient work arounds in application code, or a complete redesign, may be the only option. Peripheral Pin Select configuration provides an alternative to these choices by enabling peripheral set selection and placement on a wide range of I/O pins. By increasing the pinout options available on a particular device, users can better tailor the device to their entire application, rather than trimming the application to fit the device. The Peripheral Pin Select configuration feature operates over a fixed subset of digital I/O pins. Users may independently map the input and/or output of most digital peripherals to any one of these I/O pins. Hardware safeguards are included that prevent accidental or spurious changes to the peripheral mapping once it has been established. 4.6.5.1 Available Pins The number of available pins is dependent on the particular device and its pin count. Pins that support the Peripheral Pin Select feature include the label, “S1RPn”, in their full pin designation, where “n” is the remappable pin number. “S1RP” is used to designate pins that support both remappable input and output functions. 4.6.5.2 Available Peripherals The peripherals managed by the Peripheral Pin Select are all digital only peripherals. These include general serial communications (UART and SPI), general purpose timer clock inputs, timer-related peripherals (input capture and output compare) and interrupt-on-change inputs. In comparison, some digital only peripheral modules are never included in the Peripheral Pin Select feature. This is because the peripheral’s function requires special I/O circuitry on a specific port and cannot be easily connected to multiple pins. One example includes I2C modules. A similar requirement excludes all modules with analog inputs, such as the ADC Converter. A key difference between remappable and nonremappable peripherals is that remappable peripherals are not associated with a default I/O pin. The peripheral must always be assigned to a specific I/O pin before it can be used. In contrast, non-remappable peripherals are always available on a default pin, assuming that the peripheral is active and not conflicting with another peripheral.  2017-2019 Microchip Technology Inc. When a remappable peripheral is active on a given I/O pin, it takes priority over all other digital I/Os and digital communication peripherals associated with the pin. Priority is given regardless of the type of peripheral that is mapped. Remappable peripherals never take priority over any analog functions associated with the pin. 4.6.5.3 Controlling Configuration Changes Because peripheral mapping can be changed during run time, some restrictions on peripheral remapping are needed to prevent accidental configuration changes. The dsPIC33CH128MP508 devices have implemented the control register lock sequence to prevent accidental changes. 4.6.5.4 Control Register Lock Under normal operation, writes to the RPINRx and RPORx registers are not allowed. Attempted writes will appear to execute normally, but the contents of the registers will remain unchanged. To change these registers, they must be unlocked in hardware. The register lock is controlled by the IOLOCK bit (RPCON[11]). Setting IOLOCK prevents writes to the control registers; clearing IOLOCK allows writes. To set or clear IOLOCK, the NVMKEY unlock sequence must be executed: 1. 2. 3. Write 0x55 to NVMKEY. Write 0xAA to NVMKEY. Clear (or set) IOLOCK as a single operation. IOLOCK remains in one state until changed. This allows all of the Peripheral Pin Selects to be configured with a single unlock sequence, followed by an update to all of the control registers. Then, IOLOCK can be set with a second lock sequence. 4.6.5.5 Considerations for Peripheral Pin Selection The ability to control Peripheral Pin Selection introduces several considerations into application design that most users would never think of otherwise. This is particularly true for several common peripherals, which are only available as remappable peripherals. The main consideration is that the Peripheral Pin Selects are not available on default pins in the device’s default (Reset) state. More specifically, because all RPINRx registers reset to ‘1’s and RPORx registers reset to ‘0’s, this means all PPS inputs are tied to VSS, while all PPS outputs are disconnected. This means that before any other application code is executed, the user must initialize the device with the proper peripheral configuration. Because the IOLOCK bit resets in the unlocked state, it is not necessary to execute the unlock sequence after the device has come out of Reset. For application safety, however, it is always better to set IOLOCK and lock the configuration after writing to the control registers. DS70005319D-page 339 dsPIC33CH128MP508 FAMILY The NVMKEY unlock sequence must be executed as an assembly language routine. If the bulk of the application is written in C, or another high-level language, the unlock sequence should be performed by writing in-line assembly or by using the __builtin_write_RPCON(value) function provided by the compiler. Example 4-4 provides a configuration for bidirectional communication with flow control using UART1. The following input and output functions are used: Choosing the configuration requires a review of all Peripheral Pin Selects and their pin assignments, particularly those that will not be used in the application. In all cases, unused pin-selectable peripherals should be disabled completely. Unused peripherals should have their inputs assigned to an unused RPn pin function. I/O pins with unused RPn functions should be configured with the null peripheral output. EXAMPLE 4-4: MPLAB® XC16 provides a built-in C language function for unlocking and modifying the RPCON register: __builtin_write_RPCON(value); For more information, see the MPLAB XC16 Help files. Note: 4.6.5.6 Input Mapping The inputs of the Peripheral Pin Select options are mapped on the basis of the peripheral. That is, a control register associated with a peripheral dictates the pin it will be mapped to. The RPINRx registers are used to configure peripheral input mapping (see Register 4-37 through Register 4-60). Each register contains sets of 8-bit fields, with each set associated with one of the remappable peripherals. Programming a given peripheral’s bit field with an appropriate 8-bit index value maps the S1RPn pin with the corresponding value, or internal signal, to that peripheral. See Table 4-27 for a list of available inputs. • Input Functions: U1RX, U1CTS • Output Functions: U1TX, U1RTS CONFIGURING UART1 INPUT AND OUTPUT FUNCTIONS // ******************************************* // Unlock Registers //***************************************** __builtin_write_RPCON(0x0000); //***************************************** // Configure Input Functions (See Table 4-28) // Assign U1Rx To Pin RP35 //*************************** _U1RXR = 35; // Assign U1CTS To Pin RP36 //*************************** _U1CTSR = 36; //***************************************** // Configure Output Functions (See Table 4-31) //***************************************** // Assign U1Tx To Pin RP37 //*************************** _RP37 = 1; //*************************** // Assign U1RTS To Pin RP38 //*************************** _RP38 = 2; //***************************************** // Lock Registers //***************************************** __builtin_write_RPCON(0x0800); For example, Figure 4-16 illustrates remappable pin selection for the U1RX input. FIGURE 4-16: REMAPPABLE INPUT FOR U1RX U1RXR[7:0] 0 VSS 1 Master CMP1 2 U1RX Input to Peripheral Slave CMP1 n S1RP181 Note: For input only, Peripheral Pin Select functionality does not have priority over TRISx settings. Therefore, when configuring an S1RPn pin for input, the corresponding bit in the TRISx register must also be configured for input (set to ‘1’). DS70005319D-page 340  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 4-27: SLAVE REMAPPABLE PIN INPUTS RPINRx[15:8] or RPINRx[7:0] Function Available on Ports 0 VSS Internal 1 Master Comparator 1 Internal 2 Slave Comparator 1 Internal 3 Slave Comparator 2 Internal 4 Slave Comparator 3 Internal 5 Master REFCLKO Internal 6 Master PTG Trigger 30 Internal 7 Master PTG Trigger 31 Internal 8 Slave PWM Event Output C Internal 9 Slave PWM Event Output D Internal 10 Slave PWM Event Output E Internal 11 Master PWM Event Output C Internal 12 Master PWM Event Output D Internal 13 Master PWM Event Output E Internal 14-31 Reserved Reserved 32 S1RP32 Port Pin RB0 33 S1RP33 Port Pin RB1 34 S1RP34 Port Pin RB2 35 S1RP35 Port Pin RB3 36 S1RP36 Port Pin RB4 37 S1RP37 Port Pin RB5 38 S1RP38 Port Pin RB6 39 S1RP39 Port Pin RB7 40 S1RP40 Port Pin RB8 41 S1RP41 Port Pin RB9 42 S1RP42 Port Pin RB10 43 S1RP43 Port Pin RB11 44 S1RP44 Port Pin RB12 45 S1RP45 Port Pin RB13 46 S1RP46 Port Pin RB14 47 S1RP47 Port Pin RB15 48 S1RP48 Port Pin RC0 49 S1RP49 Port Pin RC1 50 S1RP50 Port Pin RC2 51 S1RP51 Port Pin RC3 52 S1RP52 Port Pin RC4 53 S1RP53 Port Pin RC5 54 S1RP54 Port Pin RC6 55 S1RP55 Port Pin RC7 56 S1RP56 Port Pin RC8 57 S1RP57 Port Pin RC9 58 S1RP58 Port Pin RC10 59 S1RP59 Port Pin RC11  2017-2019 Microchip Technology Inc. DS70005319D-page 341 dsPIC33CH128MP508 FAMILY TABLE 4-27: SLAVE REMAPPABLE PIN INPUTS (CONTINUED) RPINRx[15:8] or RPINRx[7:0] Function Available on Ports 60 S1RP60 Port Pin RC12 61 S1RP61 Port Pin RC13 62 S1RP62 Port Pin RC14 63 S1RP63 Port Pin RC15 64 S1RP64 Port Pin RD0 65 S1RP65 Port Pin RD1 66 S1RP66 Port Pin RD2 67 S1RP67 Port Pin RD3 68 S1RP68 Port Pin RD4 69 S1RP69 Port Pin RD5 70 S1RP70 Port Pin RD6 71 S1RP71 Port Pin RD7 72-161 Reserved Reserved 162 Slave On Request PWM3 Internal PWM Signal 163 Slave Off Request PWM3 Internal PWM Signal 164 Slave On Request PWM2 Internal PWM Signal 165 Slave Off Request PWM2 Internal PWM Signal 166 Slave On Request PWM1 Internal PWM Signal 167 Slave Off Request PWM1 Internal PWM Signal 168-169 Reserved Reserved 170 S1RP170 Slave Virtual S1RPV0 171 S1RP171 Slave Virtual S1RPV1 172 S1RP172 Slave Virtual S1RPV2 173 S1RP173 Slave Virtual S1RPV3 174 S1RP174 Slave Virtual S1RPV4 175 S1RP175 Slave Virtual S1RPV5 176 S1RP176 Master Virtual RPV0 177 S1RP177 Master Virtual RPV1 178 S1RP178 Master Virtual RPV2 179 S1RP179 Master Virtual RPV3 180 S1RP180 Master Virtual RPV4 181 S1RP181 Master Virtual RPV5 DS70005319D-page 342  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 4.6.5.7 Virtual Connections The dsPIC33CH128MP508S1 family devices support six virtual S1RPn pins (S1RP170-S1RP175), which are identical in functionality to all other S1RPn pins, with the exception of pinouts. These six pins are internal to the devices and are not connected to a physical device pin. These pins provide a simple way for inter-peripheral connection without utilizing a physical pin. For example, the output of the analog comparator can be connected to S1RP170 and the PWM control input can be configured for S1RP170 as well. This configuration allows the analog comparator to trigger PWM Faults without the use of an actual physical pin on the device. 4.6.5.8 Slave PPS Inputs to Master Core PPS The dsPIC33CH128MP508S1 Slave core subsystem PPS has connections to the Master core subsystem virtual PPS (S1RPV5-S1RPV0) output blocks. These inputs are mapped as S1RP175, S1RP174, S1RP173, S1RP172, S1RP171 and S1RP170. The S1RPn inputs, S1RP1-S1RP13, are connected to internal signals from both the Master and Slave core subsystems. Additionally, the Master core virtual PPS output blocks (RPV5-RPV0) are connected to the Slave core PPS circuitry.  2017-2019 Microchip Technology Inc. There are virtual pins in PPS to share between Master and Slave: • • • • • • • • • • • • RP181 is for Master input (RPV5) RP180 is for Master input (RPV4) RP179 is for Master input (RPV3) RP178 is for Master input (RPV2) RP177 is for Master input (RPV1) RP176 is for Master input (RPV0) S1RP175 is for Slave input (S1RPV5) S1RP174 is for Slave input (S1RPV4) S1RP173 is for Slave input (S1RPV3) S1RP172 is for Slave input (S1RPV2) S1RP171 is for Slave input (S1RPV1) S1RP170 is for Slave input (S1RPV0) The idea of the S1RPVn (Remappable Pin Virtual) is to interconnect between Master and Slave without an I/O pin. For example, the Master UART receiver can be connected to the Slave UART transmit using S1RPVn and data communication can happen from Slave to Master without using any physical pin. DS70005319D-page 343 dsPIC33CH128MP508 FAMILY TABLE 4-28: SELECTABLE INPUT SOURCES (MAPS INPUT TO FUNCTION) Input Name(1) Function Name Register Configuration Bits External Interrupt 1 S1INT1 RPINR0 INT1R[7:0] External Interrupt 2 S1INT2 RPINR1 INT2R[7:0] External Interrupt 3 S1INT3 RPINR1 INT3R[7:0] Timer1 External Clock S1T1CK RPINR2 T1CKR[7:0] SCCP Timer1 S1TCKI1 RPINR3 TCKI1R[7:0] SCCP Capture 1 S1ICM1 RPINR3 ICM1R[7:0] SCCP Timer2 S1TCKI2 RPINR4 TCKI2R[7:0] SCCP Capture 2 S1ICM2 RPINR4 ICM2R[7:0] SCCP Timer3 S1TCKI3 RPINR5 TCKI3R[7:0] SCCP Capture 3 S1ICM3 RPINR5 ICM3R[7:0] SCCP Timer4 S1TCKI4 RPINR6 TCKI4R[7:0] SCCP Capture 4 S1ICM4 RPINR6 ICM4R[7:0] Output Compare Fault A S1OCFA RPINR11 OCFAR[7:0] Output Compare Fault B S1OCFB RPINR11 OCFBR[7:0] PWM PCI Input 8 S1PCI8 RPINR12 PCI8R[7:0] PWM PCI Input 9 S1PCI9 RPINR12 PCI9R[7:0] PWM PCI Input 10 S1PCI10 RPINR13 PCI10R[7:0] PWM PCI Input 11 S1PCI11 RPINR13 PCI11R[7:0] QEI Input A S1QEIA1 RPINR14 QEIA1R[7:0] QEI Input B S1QEIB1 RPINR14 QEIB1R[7:0] QEI Index 1 Input S1QEINDX1 RPINR15 QEINDX1R[7:0] QEI Home 1 Input S1QEIHOM1 RPINR15 QEIHOM1R[7:0] S1U1RX RPINR18 U1RXR[7:0] UART1 Receive S1U1DSR RPINR18 U1DSRR[7:0] SPI1 Data Input UART1 Data-Set-Ready S1SDI1 RPINR20 SDI1R[7:0] SPI1 Clock Input S1SCK1 RPINR20 SCK1R[7:0] S1SS1 RPINR21 SS1R[7:0] Reference Clock Input S1REFOI RPINR21 REFOIR[7:0] UART1 Clear-to-Send S1U1CTS RPINR23 U1CTSR[7:0] PWM PCI Input 17 S1PCI17 RPINR37 PCI17R[7:0] PWM PCI Input 18 S1PCI18 RPINR38 PCI18R[7:0] PWM PCI Input 12 S1PCI12 RPINR42 PCI12R[7:0] PWM PCI Input 13 S1PCI13 RPINR42 PCI13R[7:0] PWM PCI Input 14 S1PCI14 RPINR43 PCI14R[7:0] PWM PCI Input 15 S1PCI15 RPINR43 PCI15R[7:0] SPI1 Slave Select PWM PCI Input 16 S1PCI16 RPINR44 PCI16R[7:0] CLC Input A S1CLCINA RPINR45 CLCINAR[7:0] CLC Input B S1CLCINB RPINR46 CLCINBR[7:0] CLC Input C S1CLCINC RPINR46 CLCINCR[7:0] CLC Input D S1CLCIND RPINR47 CLCINDR[7:0] ADC External Trigger Input (ADTRIG31) S1ADCTRG RPINR47 ADCTRGR[7:0] Note 1: Unless otherwise noted, all inputs use the Schmitt Trigger input buffers. DS70005319D-page 344  2017-2019 Microchip Technology Inc.  2017-2019 Microchip Technology Inc. TABLE 4-29: Register Bit 15 SLAVE PPS INPUT CONTROL REGISTERS Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 — RPCONL — — — — IOLOCK — — — — — — — — — — RPINR0 INT1R7 INT1R6 INT1R5 INT1R4 INT1R3 INT1R2 INT1R1 INT1R0 — — — — — — — — RPINR1 INT3R7 INT3R6 INT3R5 INT3R4 INT3R3 INT3R2 INT3R1 INT3R0 INT2R7 INT2R6 INT2R5 INT2R4 INT2R3 INT2R2 INT2R1 INT2R0 RPINR2 T1CKR7 T1CKR6 T1CKR5 T1CKR4 T1CKR3 T1CKR2 T1CKR1 T1CKR0 — — — — — — — — RPINR3 ICM1R7 ICM1R6 ICM1R5 ICM1R4 ICM1R3 ICM1R2 ICM1R1 ICM1R0 TCKI1R7 TCKI1R6 TCKI1R5 TCKI1R4 TCKI1R3 TCKI1R2 TCKI1R1 TCKI1R0 RPINR4 ICM2R7 ICM2R6 ICM2R5 ICM2R4 ICM2R3 ICM2R2 ICM2R1 ICM2R0 TCKI2R7 TCKI2R6 TCKI2R5 TCKI2R4 TCKI2R3 TCKI2R2 TCKI2R1 TCKI2R0 RPINR5 ICM3R7 ICM3R6 ICM3R5 ICM3R4 ICM3R3 ICM3R2 ICM3R1 ICM3R0 TCKI3R7 TCKI3R6 TCKI3R5 TCKI3R4 TCKI3R3 TCKI3R2 TCKI3R1 TCKI3R0 RPINR6 ICM4R7 ICM4R6 ICM4R5 ICM4R4 ICM4R3 ICM4R2 ICM4R1 ICM4R0 TCKI4R7 TCKI4R6 TCKI4R5 TCKI4R4 TCKI4R3 TCKI4R2 TCKI4R1 TCKI4R0 RPINR11 OCFBR7 OCFBR6 OCFBR5 OCFBR4 OCFBR3 OCFBR2 OCFBR1 OCFBR0 OCFAR7 OCFAR6 OCFAR5 OCFAR4 OCFAR3 OCFAR2 OCFAR1 OCFAR0 RPINR12 PCI9R7 PCI9R6 PCI9R5 PCI9R4 PCI9R3 PCI9R2 PCI9R1 PCI9R0 PCI8R7 PCI8R6 PCI8R5 PCI8R4 PCI8R3 PCI8R2 PCI8R1 PCI8R0 RPINR13 PCI11R7 PCI11R6 PCI11R5 PCI11R4 PCI11R3 PCI11R2 PCI11R1 PCI11R0 PCI10R7 PCI10R6 PCI10R5 PCI10R4 PCI10R3 PCI10R2 PCI10R1 PCI10R0 QEIB1R7 QEIB1R6 QEIB1R5 QEIB1R4 QEIB1R3 QEIB1R2 QEIB1R1 QEIB1R0 QEIA1R7 QEIA1R6 QEIA1R5 QEIA1R4 QEIA1R3 QEIA1R2 QEIA1R1 QEIA1R0 RPINR14 RPINR15 QEIHOM1R7 QEIHOM1R6 QEIHOM1R5 QEIHOM1R4 QEIHOM1R3 QEIHOM1R2 QEIHOM1R1 QEIHOM1R0 QEINDX1R7 QEINDX1R6 QEINDX1R5 QEINDX1R4 QEINDX1R3 QEINDX1R2 QEINDX1R1 QEINDX1R0 U1DSRR7 U1DSRR6 U1DSRR5 U1DSRR4 U1DSRR3 U1DSRR2 U1DSRR1 U1DSRR0 U1RXR7 U1RXR6 U1RXR5 U1RXR4 U1RXR3 U1RXR2 U1RXR1 U1RXR0 RPINR20 SCK1R7 SCK1R6 SCK1R5 SCK1R4 SCK1R3 SCK1R2 SCK1R1 SCK1R0 SDI1R7 SDI1R6 SDI1R5 SDI1R4 SDI1R3 SDI1R2 SDI1R1 SDI1R0 RPINR21 REFOIR7 REFOIR6 REFOIR5 REFOIR4 REFOIR3 REFOIR2 REFOIR1 REFOIR0 SS1R7 SS1R6 SS1R5 SS1R4 SS1R3 SS1R2 SS1R1 SS1R0 RPINR23 U1CTSR7 U1CTSR6 U1CTSR5 U1CTSR4 U1CTSR3 U1CTSR2 U1CTSR1 U1CTSR0 — — — — — — — — RPINR37 PCI17R7 PCI17R6 PCI17R5 PCI17R4 PCI17R3 PCI17R2 PCI17R1 PCI17R0 — — — — — — — — RPINR38 — — — — — — — — PCI18R7 PCI18R6 PCI18R5 PCI18R4 PCI18R3 PCI18R2 PCI18R1 PCI18R0 RPINR42 PCI13R7 PCI13R6 PCI13R5 PCI13R4 PCI13R3 PCI13R2 PCI13R1 PCI13R0 PCI12R7 PCI12R6 PWM12R5 PWM12R4 PWM12R3 PWM12R2 PWM12R1 PWM12R0 RPINR43 PCI15R7 PCI15R6 PCI15R5 PCI15R4 PCI15R3 PCI15R2 PCI15R1 PCI15R0 PCI14R7 PCI14R6 PCI14R5 PCI14R4 PCI14R3 PCI14R2 PCI14R1 PCI14R0 RPINR44 — — — — — — — — PCI16R7 PCI16R6 PCI16R5 PCI16R4 PCI16R3 PCI16R2 PCI16R1 PCI16R0 RPINR45 CLCINAR7 CLCINAR6 CLCINAR5 CLCINAR4 CLCINAR3 CLCINAR2 CLCINAR1 CLCINAR0 — — — — — — — — RPINR46 CLCINCR7 CLCINCR6 CLCINCR5 CLCINCR4 CLCINCR3 CLCINCR2 CLCINCR1 CLCINCR0 CLCINBR7 CLCINBR6 CLCINBR5 CLCINBR4 CLCINBR3 CLCINBR2 CLCINBR1 CLCINBR0 RPINR47 ADCTRGR7 ADCTRGR6 ADCTRGR5 ADCTRGR4 ADCTRGR3 ADCTRGR2 ADCTRGR1 ADCTRGR0 CLCINDR7 CLCINDR6 CLCINDR5 CLCINDR4 CLCINDR3 CLCINDR2 CLCINDR1 CLCINDR0 DS70005319D-page 345 dsPIC33CH128MP508 FAMILY RPINR18 dsPIC33CH128MP508 FAMILY 4.6.5.9 4.6.5.10 Output Mapping In contrast to inputs, the outputs of the Peripheral Pin Select options are mapped on the basis of the pin. In this case, a control register associated with a particular pin dictates the peripheral output to be mapped. The RPORx registers are used to control output mapping. Each register contains sets of 6-bit fields, with each set associated with one S1RPn pin (see Register 4-61 through Register 4-83). The value of the bit field corresponds to one of the peripherals and that peripheral’s output is mapped to the pin (see Table 4-31 and Figure 4-17). Mapping Limitations The control schema of the peripheral select pins is not limited to a small range of fixed peripheral configurations. There are no mutual or hardware-enforced lockouts between any of the peripheral mapping SFRs. Literally any combination of peripheral mappings, across any or all of the S1RPn pins, is possible. This includes both many-to-one and one-to-many mappings of peripheral inputs, and outputs to pins. While such mappings may be technically possible from a configuration point of view, they may not be supportable from an electrical point of view. A null output is associated with the PPS Output register Reset value of ‘0’. This is done to ensure that remappable outputs remain disconnected from all output pins by default. FIGURE 4-17: MULTIPLEXING REMAPPABLE OUTPUTS FOR S1RPn RPnR[5:0] Default S1U1TX Output S1U1RTS Output 0 1 2 Output Data MPTGTRG2 S1CLC3OUT S1RP32-S1RP71 (Physical Pins) 49 50 S1RP170-S1RP175 (Internal Virtual Output Ports) Note 1: There are six virtual output ports which are not connected to any I/O ports (S1RP170-S1RP175). These virtual ports can be accessed by RPOR20, RPOR21 and RPOR22. DS70005319D-page 346  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 4-30: SLAVE REMAPPABLE OUTPUT PIN REGISTERS Register S1RP Pin I/O Port RPOR0[5:0] RPOR0[13:8] RPOR1[5:0] RPOR1[13:8] RPOR2[5:0] RPOR2[13:8] RPOR3[5:0] RPOR3[13:8] RPOR4[5:0] RPOR4[13:8] RPOR5[5:0] RPOR5[13:8] RPOR6[5:0] RPOR6[13:8] RPOR7[5:0] RPOR7[13:8] RPOR8[5:0] RPOR8[13:8] RPOR9[5:0] RPOR9[13:8] RPOR10[5:0] RPOR10[13:8] RPOR11[5:0] RPOR11[13:8] RPOR12[5:0] RPOR12[13:8] RPOR13[5:0] RPOR13[13:8] RPOR14[5:0] RPOR14[13:8] RPOR15[5:0] RPOR15[13:8] RPOR16[5:0] RPOR16[13:8] RPOR17[5:0] RPOR17[13:8] RPOR18[5:0] RPOR18[13:8] RPOR19[5:0] RPOR19[13:8] RPOR20[5:0] RPOR20[13:8] RPOR21[5:0] RPOR21[13:8] RPOR22[5:0] RPOR22[13:8] S1RP32 S1RP33 S1RP34 S1RP35 S1RP36 S1RP37 S1RP38 S1RP39 S1RP40 S1RP41 S1RP42 S1RP43 S1RP44 S1RP45 S1RP46 S1RP47 S1RP48 S1RP49 S1RP50 S1RP51 S1RP52 S1RP53 S1RP54 S1RP55 S1RP56 S1RP57 S1RP58 S1RP59 S1RP60 S1RP61 S1RP62 S1RP63 S1RP64 S1RP65 S1RP66 S1RP67 S1RP68 S1RP69 S1RP70 S1RP71 S1RP170 S1RP171 S1RP172 S1RP173 S1RP174 S1RP175 Port Pin S1RB0 Port Pin S1RB1 Port Pin S1RB2 Port Pin S1RB3 Port Pin S1RB4 Port Pin S1RB5 Port Pin S1RB6 Port Pin S1RB7 Port Pin S1RB8 Port Pin S1RB9 Port Pin S1RB10 Port Pin S1RB11 Port Pin S1RB12 Port Pin S1RB13 Port Pin S1RB14 Port Pin S1RB15 Port Pin S1RC0 Port Pin S1RC1 Port Pin S1RC2 Port Pin S1RC3 Port Pin S1RC4 Port Pin S1RC5 Port Pin S1RC6 Port Pin S1RC7 Port Pin S1RC8 Port Pin S1RC9 Port Pin S1RC10 Port Pin S1RC11 Port Pin S1RC12 Port Pin S1RC13 Port Pin S1RC14 Port Pin S1RC15 Port Pin S1RD0 Port Pin S1RD1 Port Pin S1RD2 Port Pin S1RD3 Port Pin S1RD4 Port Pin S1RD5 Port Pin S1RD6 Port Pin S1RD7 Virtual Pin S1RPV0 Virtual Pin S1RPV1 Virtual Pin S1RPV2 Virtual Pin S1RPV3 Virtual Pin S1RPV4 Virtual Pin S1RPV5  2017-2019 Microchip Technology Inc. DS70005319D-page 347 dsPIC33CH128MP508 FAMILY TABLE 4-31: OUTPUT SELECTION FOR REMAPPABLE PINS (S1RPn) Function RPnR[5:0] Output Name Default PORT 0 S1RPn tied to Default Pin S1U1TX 1 S1RPn tied to UART1 Transmit S1U1RTS 2 S1RPn tied to UART1 Request-to-Send S1SDO1 3 S1RPn tied to SPI1 Data Output S1SCK1OUT 6 S1RPn tied to SPI1 Clock Output S1SS1OUT 7 S1RPn tied to SPI1 Slave Select S1REFCLKO 14 S1RPn tied to Reference Clock Output S1OCM1 15 S1RPn tied to SCCP1 Output S1OCM2 16 S1RPn tied to SCCP2 Output S1OCM3 17 S1RPn tied to SCCP3 Output S1OCM4 18 S1RPn tied to SCCP4 Output S1CMP1 23 S1RPn tied to Comparator 1 Output S1CMP2 24 S1RPn tied to Comparator 2 Output S1CMP3 25 S1RPn tied to Comparator 3 Output S1PWMH4 34 S1RPn tied to PWM4H Output S1PWML4 35 S1RPn tied to PWM4L Output S1PWMEA 36 S1RPn tied to PWM Event A Output S1PWMEB 37 S1RPn tied to PWM Event B Output S1QEICMP1 38 S1RPn tied to QEI Comparator Output S1CLC1OUT 40 S1RPn tied to CLC1 Output S1CLC2OUT 41 S1RPn tied to CLC2 Output S1PWMEC 44 S1RPn tied to PWM Event C Output S1PWMED 45 S1RPn tied to PWM Event D Output MPTGTRG1 46 Master PTG24 Output MPTGTRG2 47 Master PTG25 Output S1CLC3OUT 50 S1RPn tied to CLC3 Output DS70005319D-page 348  2017-2019 Microchip Technology Inc.  2017-2019 Microchip Technology Inc. TABLE 4-32: Register SLAVE PPS OUTPUT CONTROL REGISTERS Bit 15 Bit 14 RPOR0 — — RP33R5 RPOR1 — — RP35R5 RPOR2 — — RP37R5 RPOR3 — — RPOR4 — RPOR5 Bit 12 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 RP33R4 RP33R3 RP33R2 RP33R1 RP33R0 — — RP32R5 RP32R4 RP32R3 RP32R2 RP32R1 RP32R0 RP35R4 RP35R3 RP35R2 RP35R1 RP35R0 — — RP34R5 RP34R4 RP34R3 RP34R2 RP34R1 RP34R0 RP37R4 RP37R3 RP37R2 RP37R1 RP37R0 — — RP36R5 RP36R4 RP36R3 RP36R2 RP36R1 RP36R0 RP39R5 RP39R4 RP39R3 RP39R2 RP39R1 RP39R0 — — RP38R5 RP38R4 RP38R3 RP38R2 RP38R1 RP38R0 — RP41R5 RP41R4 RP41R3 RP41R2 RP41R1 RP41R0 — — RP40R5 RP40R4 RP40R3 RP40R2 RP40R1 RP40R0 — — RP43R5 RP43R4 RP43R3 RP43R2 RP43R1 RP43R0 — — RP42R5 RP42R4 RP42R3 RP42R2 RP42R1 RP42R0 RPOR6 — — RP45R5 RP45R4 RP45R3 RP45R2 RP45R1 RP45R0 — — RP44R5 RP44R4 RP44R3 RP44R2 RP44R1 RP44R0 RPOR7 — — RP47R5 RP47R4 RP47R3 RP47R2 RP47R1 RP47R0 — — RP46R5 RP46R4 RP46R3 RP46R2 RP46R1 RP46R0 RPOR8 — — RP49R5 RP49R4 RP49R3 RP49R2 RP49R1 RP49R0 — — RP48R5 RP48R4 RP48R3 RP48R2 RP48R1 RP48R0 RPOR9 — — RP51R5 RP51R4 RP51R3 RP51R2 RP51R1 RP51R0 — — RP50R5 RP50R4 RP50R3 RP50R2 RP50R1 RP50R0 RPOR10 — — RP53R5 RP53R4 RP53R3 RP53R2 RP53R1 RP53R0 — — RP52R5 RP52R4 RP52R3 RP52R2 RP52R1 RP52R0 RPOR11 — — RP55R5 RP55R4 RP55R3 RP55R2 RP55R1 RP55R0 — — RP54R5 RP54R4 RP54R3 RP54R2 RP54R1 RP54R0 RPOR12 — — RP57R5 RP57R4 RP57R3 RP57R2 RP57R1 RP57R0 — — RP56R5 RP56R4 RP56R3 RP56R2 RP56R1 RP56R0 RPOR13 — — RP59R5 RP59R4 RP59R3 RP59R2 RP59R1 RP59R0 — — RP58R5 RP58R4 RP58R3 RP58R2 RP58R1 RP58R0 RPOR14 — — RP61R5 RP61R4 RP61R3 RP61R2 RP61R1 RP61R0 — — RP60R5 RP60R4 RP60R3 RP60R2 RP60R1 RP60R0 RPOR15 — — RP63R5 RP63R4 RP63R3 RP63R2 RP63R1 RP63R0 — — RP62R5 RP62R4 RP62R3 RP62R2 RP62R1 RP62R0 RPOR16 — — RP65R5 RP65R4 RP65R3 RP65R2 RP65R1 RP65R0 — — RP64R5 RP64R4 RP64R3 RP64R2 RP64R1 RP64R0 RPOR17 — — RP67R5 RP67R4 RP67R3 RP67R2 RP67R1 RP67R0 — — RP66R5 RP66R4 RP66R3 RP66R2 RP66R1 RP66R0 RPOR18 — — RP69R5 RP69R4 RP69R3 RP69R2 RP69R1 RP69R0 — — RP68R5 RP68R4 RP68R3 RP68R2 RP68R1 RP68R0 RPOR19 — — RP71R5 RP71R4 RP71R3 RP71R2 RP71R1 RP71R0 — — RP70R5 RP70R4 RP70R3 RP70R2 RP70R1 RP70R0 RPOR20(1) — — RP171R5 RP171R4 RP171R3 RP177R2 RP171R1 RP171R0 — — RP170R5 RP170R4 RP170R3 RP170R2 RP170R1 RP170R0 RPOR21(1) — — RP173R5 RP173R4 RP173R3 RP173R2 RP173R1 RP173R0 — — RP172R5 RP172R4 RP172R3 RP172R2 RP172R1 RP172R0 RPOR22(1) — — RP175R5 RP175R4 RP175R3 RP175R2 RP175R1 RP175R0 — — RP174R5 RP174R4 RP174R3 RP174R2 RP174R1 RP174R0 The RPOR20, RPOR21 and RPOR22 registers are for virtual output pins. DS70005319D-page 349 dsPIC33CH128MP508 FAMILY Bit 11 Note 1: Bit 13 dsPIC33CH128MP508 FAMILY 4.6.6 1. 2. I/O HELPFUL TIPS In some cases, certain pins, as defined in Table 24-18 under “Injection Current”, have internal protection diodes to VDD and VSS. The term, “Injection Current”, is also referred to as “Clamp Current”. On designated pins, with sufficient external current-limiting precautions by the user, I/O pin input voltages are allowed to be greater or lesser than the data sheet absolute maximum ratings, with respect to the VSS and VDD supplies. Note that when the user application forward biases either of the high or low-side internal input clamp diodes, that the resulting current being injected into the device, that is clamped internally by the VDD and VSS power rails, may affect the ADC accuracy by four to six counts. I/O pins that are shared with any analog input pin (i.e., ANx) are always analog pins, by default, after any Reset. Consequently, configuring a pin as an analog input pin automatically disables the digital input pin buffer and any attempt to read the digital input level by reading PORTx or LATx will always return a ‘0’, regardless of the digital logic level on the pin. To use a pin as a digital I/O pin on a shared ANx pin, the user application needs to configure the Analog Select for PORTx registers, in the I/O ports module (i.e., ANSELx), by setting the appropriate bit that corresponds to that I/O port pin to a ‘0’. Note: Although it is not possible to use a digital input pin when its analog function is enabled, it is possible to use the digital I/O output function, TRISx = 0x0, while the analog function is also enabled. However, this is not recommended, particularly if the analog input is connected to an external analog voltage source, which would create signal contention between the analog signal and the output pin driver. DS70005319D-page 350 3. 4. 5. Most I/O pins have multiple functions. Referring to the device pin diagrams in this data sheet, the priorities of the functions allocated to any pins are indicated by reading the pin name, from left-to-right. The left most function name takes precedence over any function to its right in the naming convention. For example: AN16/T2CK/T7CK/RC1; this indicates that AN16 is the highest priority in this example and will supersede all other functions to its right in the list. Those other functions to its right, even if enabled, would not work as long as any other function to its left was enabled. This rule applies to all of the functions listed for a given pin. Each pin has an internal weak pull-up resistor and pull-down resistor that can be configured using the CNPUx and CNPDx registers, respectively. These resistors eliminate the need for external resistors in certain applications. The internal pull-up is up to ~(VDD – 0.8), not VDD. This value is still above the minimum VIH of CMOS and TTL devices. When driving LEDs directly, the I/O pin can source or sink more current than what is specified in the VOH/IOH and VOL/IOL DC characteristics specification. The respective IOH and IOL current rating only applies to maintaining the corresponding output at or above the VOH, and at or below the VOL levels. However, for LEDs, unlike digital inputs of an externally connected device, they are not governed by the same minimum VIH/VIL levels. An I/O pin output can safely sink or source any current less than that listed in the Absolute Maximum Ratings in Section 24.0 “Electrical Characteristics” of this data sheet. For example: VOH = 2.4v @ IOH = -8 mA and VDD = 3.3V The maximum output current sourced by any 8 mA I/O pin = 12 mA. LED source current < 12 mA is technically permitted.  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 6. The Peripheral Pin Select (PPS) pin mapping rules are as follows: a) Only one “output” function can be active on a given pin at any time, regardless if it is a dedicated or remappable function (one pin, one output). b) It is possible to assign a “remappable output” function to multiple pins and externally short or tie them together for increased current drive. c) If any “dedicated output” function is enabled on a pin, it will take precedence over any remappable “output” function. d) If any “dedicated digital” (input or output) function is enabled on a pin, any number of “input” remappable functions can be mapped to the same pin. e) If any “dedicated analog” function(s) are enabled on a given pin, “digital input(s)” of any kind will all be disabled, although a single “digital output”, at the user’s cautionary discretion, can be enabled and active as long as there is no signal contention with an external analog input signal. For example, it is possible for the ADC to convert the digital output logic level, or to toggle a digital output on a comparator or ADC input, provided there is no external analog input, such as for a Built-In Self-Test. f) Any number of “input” remappable functions can be mapped to the same pin(s) at the same time, including to any pin with a single output from either a dedicated or remappable “output”. g) The TRISx registers control only the digital I/O output buffer. Any other dedicated or remappable active “output” will automatically override the TRISx setting. The TRISx register does not control the digital logic “input” buffer. Remappable digital “inputs” do not automatically override TRISx settings, which means that the TRISx bit must be set to input for pins with only remappable input function(s) assigned. h) All analog pins are enabled by default after any Reset and the corresponding digital input buffer on the pin has been disabled. Only the Analog Select for PORTx (ANSELx) registers control the digital input buffer, not the TRISx register. The user must disable the analog function on a pin using the Analog Select for PORTx registers in order to use any “digital input(s)” on a corresponding pin, no exceptions.  2017-2019 Microchip Technology Inc. 4.6.7 I/O PORTS RESOURCES Many useful resources are provided on the main product page of the Microchip website for the devices listed in this data sheet. This product page contains the latest updates and additional information. 4.6.7.1 Key Resources • “I/O Ports with Edge Detect” (www.microchip.com/DS70005322) in the “dsPIC33/PIC24 Family Reference Manual” • Code Samples • Application Notes • Software Libraries • Webinars • All Related “dsPIC33/PIC24 Family Reference Manual” Sections • Development Tools DS70005319D-page 351 dsPIC33CH128MP508 FAMILY 4.6.8 PERIPHERAL PIN SELECT REGISTERS REGISTER 4-36: RPCON: PERIPHERAL REMAPPING CONFIGURATION REGISTER U-0 U-0 U-0 U-0 R/W-0 U-0 U-0 U-0 — — — — IOLOCK — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-12 Unimplemented: Read as ‘0’ bit 11 IOLOCK: Peripheral Remapping Register Lock bit 1 = All Peripheral Remapping registers are locked and cannot be written 0 = All Peripheral Remapping registers are unlocked and can be written bit 10-0 Unimplemented: Read as ‘0’ REGISTER 4-37: RPINR0: PERIPHERAL PIN SELECT INPUT REGISTER 0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INT1R7 INT1R6 INT1R5 INT1R4 INT1R3 INT1R2 INT1R1 INT1R0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 INT1R[7:0]: Assign External Interrupt 1 (S1INT1) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 Unimplemented: Read as ‘0’ DS70005319D-page 352  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-38: RPINR1: PERIPHERAL PIN SELECT INPUT REGISTER 1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INT3R15 INT3R14 INT3R13 INT3R12 INT3R11 INT3R10 INT3R9 INT3R8 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INT2R7 INT2R6 INT2R5 INT2R4 INT2R3 INT2R2 INT2R1 INT2R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 INT3R[15:8]: Assign External Interrupt 3 (S1INT3) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 INT2R[7:0]: Assign External Interrupt 2 (S1INT2) to the Corresponding S1RPn Pin bits See Table 4-27. REGISTER 4-39: RPINR2: PERIPHERAL PIN SELECT INPUT REGISTER 2 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 T1CKR7 T1CKR6 T1CKR5 T1CKR4 T1CKR3 T1CKR2 T1CKR1 T1CKR0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 T1CKR[7:0]: Assign Timer1 External Clock (S1T1CK) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. DS70005319D-page 353 dsPIC33CH128MP508 FAMILY REGISTER 4-40: RPINR3: PERIPHERAL PIN SELECT INPUT REGISTER 3 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ICM1R7 ICM1R6 ICM1R5 ICM1R4 ICM1R3 ICM1R2 ICM1R1 ICM1R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TCKI1R7 TCKI1R6 TCKI1R5 TCKI1R4 TCKI1R3 TCKI1R2 TCKI1R1 TCKI1R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 ICM1R[7:0]: Assign SCCP Capture 1 (S1ICM1) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 TCKI1R[7:0]: Assign SCCP Timer1 (S1TCKI1) to the Corresponding S1RPn Pin bits See Table 4-27. REGISTER 4-41: RPINR4: PERIPHERAL PIN SELECT INPUT REGISTER 4 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ICM2R7 ICM2R6 ICM2R5 ICM2R4 ICM2R3 ICM2R2 ICM2R1 ICM2R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TCKI2R7 TCKI2R6 TCKI2R5 TCKI2R4 TCKI2R3 TCKI2R2 TCKI2R1 TCKI2R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 ICM2R[7:0]: Assign SCCP Capture 2 (S1ICM2) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 TCKI2R[7:0]: Assign SCCP Timer2 (S1TCKI2) to the Corresponding S1RPn Pin bits See Table 4-27. DS70005319D-page 354  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-42: RPINR5: PERIPHERAL PIN SELECT INPUT REGISTER 5 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ICM3R7 ICM3R6 ICM3R5 ICM3R4 ICM3R3 ICM3R2 ICM3R1 ICM3R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TCKI3R7 TCKI3R6 TCKI3R5 TCKI3R4 TCKI3R3 TCKI3R2 TCKI3R1 TCKI3R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 ICM3R[7:0]: Assign SCCP Capture 3 (S1ICM3) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 TCKI3R[7:0]: Assign SCCP Timer3 (S1TCKI3) to the Corresponding S1RPn Pin bits See Table 4-27. REGISTER 4-43: RPINR6: PERIPHERAL PIN SELECT INPUT REGISTER 6 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ICM4R7 ICM4R6 ICM4R5 ICM4R4 ICM4R3 ICM4R2 ICM4R1 ICM4R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TCKI4R7 TCKI4R6 TCKI4R5 TCKI4R4 TCKI4R3 TCKI4R2 TCKI4R1 TCKI4R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 ICM4R[7:0]: Assign SCCP Capture 4 (S1ICM4) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 TCKI4R[7:0]: Assign SCCP Timer4 (S1TCKI4) to the Corresponding S1RPn Pin bits See Table 4-27.  2017-2019 Microchip Technology Inc. DS70005319D-page 355 dsPIC33CH128MP508 FAMILY REGISTER 4-44: RPINR11: PERIPHERAL PIN SELECT INPUT REGISTER 11 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 OCFBR7 OCFBR6 OCFBR5 OCFBR4 OCFBR3 OCFBR2 OCFBR1 OCFBR0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 OCFAR7 OCFAR6 OCFAR5 OCFAR4 OCFAR3 OCFAR2 OCFAR1 OCFAR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 OCFBR[7:0]: Assign Output Compare Fault B (S1OCFB) to the Corresponding S1RPn Pin bits See Table 4-27 bit 7-0 OCFBA[7:0]: Assign Output Compare Fault A (S1OCFA) to the Corresponding S1RPn Pin bits See Table 4-27 REGISTER 4-45: RPINR12: PERIPHERAL PIN SELECT INPUT REGISTER 12 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI9R7 PCI9R6 PCI9R5 PCI9R4 PCI9R3 PCI9R2 PCI9R1 PCI9R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI8R7 PCI8R6 PCI8R5 PCI8R4 PCI8R3 PCI8R2 PCI8R1 PCI8R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 PCI9R[7:0]: Assign PWM Input 9 (S1PCI9) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 PCI8R[7:0]: Assign PWM Input 8 (S1PCI8) to the Corresponding S1RPn Pin bits See Table 4-27. DS70005319D-page 356  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-46: RPINR13: PERIPHERAL PIN SELECT INPUT REGISTER 13 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI11R7 PCI11R6 PCI11R5 PCI11R4 PCI11R3 PCI11R2 PCI11R1 PCI11R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI10R7 PCI10R6 PCI10R5 PCI10R4 PCI10R3 PCI10R2 PCI10R1 PCI10R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 PCI11R[7:0]: Assign PWM Input 11 (S1PCI11) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 PCI10R[7:0]: Assign PWM Input 10 (S1PCI10) to the Corresponding S1RPn Pin bits See Table 4-27. REGISTER 4-47: RPINR14: PERIPHERAL PIN SELECT INPUT REGISTER 14 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 QEIB1R7 QEIB1R6 QEIB1R5 QEIB1R4 QEIB1R3 QEIB1R2 QEIB1R1 QEIB1R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 QEIA1R7 QEIA1R6 QEIA1R5 QEIA1R4 QEIA1R3 QEIA1R2 QEIA1R1 QEIA1R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 QEIB1R[7:0]: Assign QEI Input B (S1QEIB1) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 QEIA1R[7:0]: Assign QEI Input A (S1QEIA1) to the Corresponding S1RPn Pin bits See Table 4-27.  2017-2019 Microchip Technology Inc. DS70005319D-page 357 dsPIC33CH128MP508 FAMILY REGISTER 4-48: R/W-0 QEIHOM1R7 RPINR15: PERIPHERAL PIN SELECT INPUT REGISTER 15 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 QEIHOM1R6 QEIHOM1R5 QEIHOM1R4 QEIHOM1R3 QEIHOM1R2 QEIHOM1R1 QEIHOM1R0 bit 15 bit 8 R/W-0 QEINDX1R7 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 QEINDX1R6 QEINDX1R5 QEINDX1R4 QEINDX1R3 QEINDX1R2 R/W-0 R/W-0 QEINDX1R1 QEINDX1R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 QEIHOM1R[7:0]: Assign QEI Home 1 Input (S1QEIHOM1) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 QEINDX1R[7:0]: Assign QEI Index 1 Input (S1QEINDX1) to the Corresponding S1RPn Pin bits See Table 4-27. REGISTER 4-49: RPINR18: PERIPHERAL PIN SELECT INPUT REGISTER 18 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U1DSRR7 U1DSRR6 U1DSRR5 U1DSRR4 U1DSRR3 U1DSRR2 U1DSRR1 U1DSRR0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U1RXR7 U1RXR6 U1RXR5 U1RXR4 U1RXR3 U1RXR2 U1RXR1 U1RXR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 U1DSRR[7:0]: Assign UART1 Data-Set-Ready (S1U1DSR) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 U1RXR[7:0]: Assign UART1 Receive (S1U1RX) to the Corresponding S1RPn Pin bits See Table 4-27. DS70005319D-page 358  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-50: RPINR20: PERIPHERAL PIN SELECT INPUT REGISTER 20 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SCK1R7 SCK1R6 SCK1R5 SCK1R4 SCK1R3 SCK1R2 SCK1R1 SCK1R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SDI1R7 SDI1R6 SDI1R5 SDI1R4 SDI1R3 SDI1R2 SDI1R1 SDI1R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 SCK1R[7:0]: Assign SPI1 Clock Input (S1SCK1) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 SDI1R[7:0]: Assign SPI1 Data Input (S1SDI1) to the Corresponding S1RPn Pin bits See Table 4-27. REGISTER 4-51: RPINR21: PERIPHERAL PIN SELECT INPUT REGISTER 21 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 REFOIR7 REFOIR6 REFOIR5 REFOIR4 REFOIR3 REFOIR2 REFOIR1 REFOIR0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SS1R7 SS1R6 SS1R5 SS1R4 SS1R3 SS1R2 SS1R1 SS1R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 REFOIR[7:0]: Assign Reference Clock Input (S1REFOI) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 SS1R[7:0]: Assign SPI1 Slave Select (S1SS1) to the Corresponding S1RPn Pin bits See Table 4-27.  2017-2019 Microchip Technology Inc. DS70005319D-page 359 dsPIC33CH128MP508 FAMILY REGISTER 4-52: RPINR23: PERIPHERAL PIN SELECT INPUT REGISTER 23 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U1CTSR7 U1CTSR6 U1CTSR5 U1CTSR4 U1CTSR3 U1CTSR2 U1CTSR1 U1CTSR0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 U1CTSR[7:0]: Assign UART1 Clear-to-Send (S1U1CTS) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 Unimplemented: Read as ‘0’ REGISTER 4-53: RPINR37: PERIPHERAL PIN SELECT INPUT REGISTER 37 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI17R7 PCI17R6 PCI17R5 PCI17R4 PCI17R3 PCI17R2 PCI17R1 PCI17R0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 PCI17R[7:0]: Assign PWM Input 17 (S1PCI17) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 Unimplemented: Read as ‘0’ DS70005319D-page 360  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-54: RPINR38: PERIPHERAL PIN SELECT INPUT REGISTER 38 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI18R7 PCI18R6 PCI18R5 PCI18R4 PCI18R3 PCI18R2 PCI18R1 PCI18R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7-0 PCI18R[7:0]: Assign PWM Input 18 (S1PCI18) to the Corresponding S1RPn Pin bits See Table 4-27. REGISTER 4-55: RPINR42: PERIPHERAL PIN SELECT INPUT REGISTER 42 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI13R7 PCI13R6 PCI13R5 PCI13R4 PCI13R3 PCI13R2 PCI13R1 PCI13R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI12R7 PCI12R6 PCI12R5 PCI12R4 PCI12R3 PCI12R2 PCI12R1 PCI12R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 PCI13R[7:0]: Assign PWM Input 13 (S1PCI13) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 PCI12R[7:0]: Assign PWM Input 12 (S1PCI12) to the Corresponding S1RPn Pin bits See Table 4-27.  2017-2019 Microchip Technology Inc. DS70005319D-page 361 dsPIC33CH128MP508 FAMILY REGISTER 4-56: RPINR43: PERIPHERAL PIN SELECT INPUT REGISTER 43 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI15R7 PCI15R6 PCI15R5 PCI15R4 PCI15R3 PCI15R2 PCI15R1 PCI15R0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI14R7 PCI14R6 PCI14R5 PCI14R4 PCI14R3 PCI14R2 PCI14R1 PCI14R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 PCI15R[7:0]: Assign PWM Input 15 (S1PCI15) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 PCI14R[7:0]: Assign PWM Input 14 (S1PCI14) to the Corresponding S1RPn Pin bits See Table 4-27. REGISTER 4-57: RPINR44: PERIPHERAL PIN SELECT INPUT REGISTER 44 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCI16R7 PCI16R6 PCI16R5 PCI16R4 PCI16R3 PCI16R2 PCI16R1 PCI16R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7-0 PCI16[7:0]: Assign PWM Input 16 (S1PCI16) to the Corresponding S1RPn Pin bits See Table 4-27. DS70005319D-page 362  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-58: RPINR45: PERIPHERAL PIN SELECT INPUT REGISTER 45 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CLCINAR7 CLCINAR6 CLCINAR5 CLCINAR4 CLCINAR3 CLCINAR2 CLCINAR1 CLCINAR0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 CLCINAR[7:0]: Assign CLC Input A (S1CLCINA) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 Unimplemented: Read as ‘0’ REGISTER 4-59: RPINR46: PERIPHERAL PIN SELECT INPUT REGISTER 46 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CLCINCR7 CLCINCR6 CLCINCR5 CLCINCR4 CLCINCR3 CLCINCR2 CLCINCR1 CLCINCR0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CLCINBR7 CLCINBR6 CLCINBR5 CLCINBR4 CLCINBR3 CLCINBR2 CLCINBR1 CLCINBR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 CLCINCR[7:0]: Assign CLC Input C (S1CLCINC) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 CLCINBR[7:0]: Assign CLC Input B (S1CLCINB) to the Corresponding S1RPn Pin bits See Table 4-27.  2017-2019 Microchip Technology Inc. DS70005319D-page 363 dsPIC33CH128MP508 FAMILY REGISTER 4-60: RPINR47: PERIPHERAL PIN SELECT INPUT REGISTER 47 R/W-0 R/W-0 ADCTRGR7 ADCTRGR6 R/W-0 R/W-0 R/W-0 ADCTRGR5 ADCTRGR4 ADCTRGR3 R/W-0 R/W-0 R/W-0 ADCTRGR2 ADCTRGR1 ADCTRGR0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CLCINDR7 CLCINDR6 CLCINDR5 CLCINDR4 CLCINDR3 CLCINDR2 CLCINDR1 CLCINDR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 ADCTRGR[7:0]: Assign ADC External Trigger Input (S1ADCTRG) to the Corresponding S1RPn Pin bits See Table 4-27. bit 7-0 CLCINDR[7:0]: Assign CLC Input D (S1CLCIND) to the Corresponding S1RPn Pin bits See Table 4-27. DS70005319D-page 364  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-61: RPOR0: PERIPHERAL PIN SELECT OUTPUT REGISTER 0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP33R5 RP33R4 RP33R3 RP33R2 RP33R1 RP33R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP32R5 RP32R4 RP32R3 RP32R2 RP32R1 RP32R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP33R[5:0]: Peripheral Output Function is Assigned to S1RP33 Output Pin bits (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP32R[5:0]: Peripheral Output Function is Assigned to S1RP32 Output Pin bits (see Table 4-31 for peripheral function numbers) REGISTER 4-62: RPOR1: PERIPHERAL PIN SELECT OUTPUT REGISTER 1 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP35R5 RP35R4 RP35R3 RP35R2 RP35R1 RP35R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP34R5 RP34R4 RP34R3 RP34R2 RP34R1 RP34R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP35R[5:0]: Peripheral Output Function is Assigned to S1RP35 Output Pin bits (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP34R[5:0]: Peripheral Output Function is Assigned to S1RP34 Output Pin bits (see Table 4-31 for peripheral function numbers)  2017-2019 Microchip Technology Inc. DS70005319D-page 365 dsPIC33CH128MP508 FAMILY REGISTER 4-63: RPOR2: PERIPHERAL PIN SELECT OUTPUT REGISTER 2 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP37R5 RP37R4 RP37R3 RP37R2 RP37R1 RP37R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP36R5 RP36R4 RP36R3 RP36R2 RP36R1 RP36R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP37R[5:0]: Peripheral Output Function is Assigned to S1RP37 Output Pin bits (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP36R[5:0]: Peripheral Output Function is Assigned to S1RP36 Output Pin bits (see Table 4-31 for peripheral function numbers) REGISTER 4-64: RPOR3: PERIPHERAL PIN SELECT OUTPUT REGISTER 3 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP39R5 RP39R4 RP39R3 RP39R2 RP39R1 RP39R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP38R5 RP38R4 RP38R3 RP38R2 RP38R1 RP38R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP39R[5:0]: Peripheral Output Function is Assigned to S1RP39 Output Pin bits (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP38R[5:0]: Peripheral Output Function is Assigned to S1RP38 Output Pin bits (see Table 4-31 for peripheral function numbers) DS70005319D-page 366  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-65: RPOR4: PERIPHERAL PIN SELECT OUTPUT REGISTER 4 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP41R5 RP41R4 RP41R3 RP41R2 RP41R1 RP41R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP40R5 RP40R4 RP40R3 RP40R2 RP40R1 RP40R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP41R[5:0]: Peripheral Output Function is Assigned to S1RP41 Output Pin bits (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP40R[5:0]: Peripheral Output Function is Assigned to S1RP40 Output Pin bits (see Table 4-31 for peripheral function numbers) REGISTER 4-66: RPOR5: PERIPHERAL PIN SELECT OUTPUT REGISTER 5 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP43R5 RP43R4 RP43R3 RP43R2 RP43R1 RP43R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP42R5 RP42R4 RP42R3 RP42R2 RP42R1 RP42R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP43R[5:0]: Peripheral Output Function is Assigned to S1RP43 Output Pin bits (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP42R[5:0]: Peripheral Output Function is Assigned to S1RP42 Output Pin bits (see Table 4-31 for peripheral function numbers)  2017-2019 Microchip Technology Inc. DS70005319D-page 367 dsPIC33CH128MP508 FAMILY REGISTER 4-67: RPOR6: PERIPHERAL PIN SELECT OUTPUT REGISTER 6 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP45R5 RP45R4 RP45R3 RP45R2 RP45R1 RP45R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP44R5 RP44R4 RP44R3 RP44R2 RP44R1 RP44R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP45R[5:0]: Peripheral Output Function is Assigned to S1RP45 Output Pin bits (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP44R[5:0]: Peripheral Output Function is Assigned to S1RP44 Output Pin bits (see Table 4-31 for peripheral function numbers) REGISTER 4-68: RPOR7: PERIPHERAL PIN SELECT OUTPUT REGISTER 7 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP47R5 RP47R4 RP47R3 RP47R2 RP47R1 RP47R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP46R5 RP46R4 RP46R3 RP46R2 RP46R1 RP46R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP47R[5:0]: Peripheral Output Function is Assigned to S1RP47 Output Pin bits (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP46R[5:0]: Peripheral Output Function is Assigned to S1RP46 Output Pin bits (see Table 4-31 for peripheral function numbers) DS70005319D-page 368  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-69: RPOR8: PERIPHERAL PIN SELECT OUTPUT REGISTER 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP49R5 RP49R4 RP49R3 RP49R2 RP49R1 RP49R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP48R5 RP48R4 RP48R3 RP48R2 RP48R1 RP48R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP49R[5:0]: Peripheral Output Function is Assigned to S1RP49 Output Pin bits (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP48R[5:0]: Peripheral Output Function is Assigned to S1RP48 Output Pin bits (see Table 4-31 for peripheral function numbers) REGISTER 4-70: RPOR9: PERIPHERAL PIN SELECT OUTPUT REGISTER 9 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP51R5 RP51R4 RP51R3 RP51R2 RP51R1 RP51R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP50R5 RP50R4 RP50R3 RP50R2 RP50R1 RP50R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP51R[5:0]: Peripheral Output Function is Assigned to S1RP51 Output Pin bits (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP50R[5:0]: Peripheral Output Function is Assigned to S1RP50 Output Pin bits (see Table 4-31 for peripheral function numbers)  2017-2019 Microchip Technology Inc. DS70005319D-page 369 dsPIC33CH128MP508 FAMILY REGISTER 4-71: RPOR10: PERIPHERAL PIN SELECT OUTPUT REGISTER 10 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP53R5 RP53R4 RP53R3 RP53R2 RP53R1 RP53R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP52R5 RP52R4 RP52R3 RP52R2 RP52R1 RP52R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP53R[5:0]: Peripheral Output Function is Assigned to S1RP53 Output Pin bits (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP52R[5:0]: Peripheral Output Function is Assigned to S1RP52 Output Pin bits (see Table 4-31 for peripheral function numbers) REGISTER 4-72: RPOR11: PERIPHERAL PIN SELECT OUTPUT REGISTER 11 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP55R5 RP55R4 RP55R3 RP55R2 RP55R1 RP55R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP54R5 RP54R4 RP54R3 RP54R2 RP54R1 RP54R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP55R[5:0]: Peripheral Output Function is Assigned to S1RP55 Output Pin bits (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP54R[5:0]: Peripheral Output Function is Assigned to S1RP54 Output Pin bits (see Table 4-31 for peripheral function numbers) DS70005319D-page 370  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-73: RPOR12: PERIPHERAL PIN SELECT OUTPUT REGISTER 12 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP57R5 RP57R4 RP57R3 RP57R2 RP57R1 RP57R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP56R5 RP56R4 RP56R3 RP56R2 RP56R1 RP56R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP57R[5:0]: Peripheral Output Function is Assigned to S1RP57 Output Pin bits (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP56R[5:0]: Peripheral Output Function is Assigned to S1RP56 Output Pin bits (see Table 4-31 for peripheral function numbers) REGISTER 4-74: RPOR13: PERIPHERAL PIN SELECT OUTPUT REGISTER 13 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP59R5 RP59R4 RP59R3 RP59R2 RP59R1 RP59R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP58R5 RP58R4 RP58R3 RP58R2 RP58R1 RP58R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP59R[5:0]: Peripheral Output Function is Assigned to S1RP59 Output Pin bits (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP58R[5:0]: Peripheral Output Function is Assigned to S1RP58 Output Pin bits (see Table 4-31 for peripheral function numbers)  2017-2019 Microchip Technology Inc. DS70005319D-page 371 dsPIC33CH128MP508 FAMILY REGISTER 4-75: RPOR14: PERIPHERAL PIN SELECT OUTPUT REGISTER 14 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP61R5 RP61R4 RP61R3 RP61R2 RP61R1 RP61R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP60R5 RP60R4 RP60R3 RP60R2 RP60R1 RP60R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP61R[5:0]: Peripheral Output Function is Assigned to S1RP61 Output Pin bits (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP60R[5:0]: Peripheral Output Function is Assigned to S1RP60 Output Pin bits (see Table 4-31 for peripheral function numbers) REGISTER 4-76: RPOR15: PERIPHERAL PIN SELECT OUTPUT REGISTER 15 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP63R5 RP63R4 RP63R3 RP63R2 RP63R1 RP63R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP62R5 RP62R4 RP62R3 RP62R2 RP62R1 RP62R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP63R[5:0]: Peripheral Output Function is Assigned to S1RP63 Output Pin bits (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP62R[5:0]: Peripheral Output Function is Assigned to S1RP62 Output Pin bits (see Table 4-31 for peripheral function numbers) DS70005319D-page 372  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-77: RPOR16: PERIPHERAL PIN SELECT OUTPUT REGISTER 16 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP65R5 RP65R4 RP65R3 RP65R2 RP65R1 RP65R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP64R5 RP64R4 RP64R3 RP64R2 RP64R1 RP64R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP65R[5:0]: Peripheral Output Function is Assigned to S1RP65 Output Pin bits (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP64R[5:0]: Peripheral Output Function is Assigned to S1RP64 Output Pin bits (see Table 4-31 for peripheral function numbers) REGISTER 4-78: RPOR17: PERIPHERAL PIN SELECT OUTPUT REGISTER 17 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP67R5 RP67R4 RP67R3 RP67R2 RP67R1 RP67R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP66R5 RP66R4 RP66R3 RP66R2 RP66R1 RP66R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP67R[5:0]: Peripheral Output Function is Assigned to S1RP67 Output Pin bits (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP66R[5:0]: Peripheral Output Function is Assigned to S1RP66 Output Pin bits (see Table 4-31 for peripheral function numbers)  2017-2019 Microchip Technology Inc. DS70005319D-page 373 dsPIC33CH128MP508 FAMILY REGISTER 4-79: RPOR18: PERIPHERAL PIN SELECT OUTPUT REGISTER 18 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP69R5 RP69R4 RP69R3 RP69R2 RP69R1 RP69R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP68R5 RP68R4 RP68R3 RP68R2 RP68R1 RP68R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP69R[5:0]: Peripheral Output Function is Assigned to S1RP69 Output Pin bits (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP68R[5:0]: Peripheral Output Function is Assigned to S1RP68 Output Pin bits (see Table 4-31 for peripheral function numbers) REGISTER 4-80: RPOR19: PERIPHERAL PIN SELECT OUTPUT REGISTER 19 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP71R5 RP71R4 RP71R3 RP71R2 RP71R1 RP71R0 bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — RP70R5 RP70R4 RP70R3 RP70R2 RP70R1 RP70R0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP71R[5:0]: Peripheral Output Function is Assigned to S1RP71 Output Pin bits (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP70R[5:0]: Peripheral Output Function is Assigned to S1RP70 Output Pin bits (see Table 4-31 for peripheral function numbers) DS70005319D-page 374  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-81: RPOR20: PERIPHERAL PIN SELECT OUTPUT REGISTER 20 U-0 U-0 R/W-0 — — RP171R5(1) R/W-0 R/W-0 RP171R4(1) RP171R3(1) R/W-0 R/W-0 R/W-0 RP171R2(1) RP171R1(1) RP171R0(1) bit 15 bit 8 U-0 U-0 R/W-0 — — RP170R5(1) R/W-0 R/W-0 RP170R4(1) RP170R3(1) R/W-0 R/W-0 R/W-0 RP170R2(1) RP170R1(1) RP170R0(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP171R[5:0]: Peripheral Output Function is Assigned to S1RP171 Output Pin bits(1) (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP170R[5:0]: Peripheral Output Function is Assigned to S1RP170 Output Pin bits(1) (see Table 4-31 for peripheral function numbers) Note 1: These are virtual output ports. REGISTER 4-82: U-0 — RPOR21: PERIPHERAL PIN SELECT OUTPUT REGISTER 21 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — RP173R5(1) RP173R4(1) RP173R3(1) RP173R2(1) RP173R1(1) RP173R0(1) bit 15 bit 8 U-0 — U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — RP172R5(1) RP172R4(1) RP172R3(1) RP172R2(1) RP172R1(1) RP172R0(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP173R[5:0]: Peripheral Output Function is Assigned to S1RP173 Output Pin bits(1) (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP172R[5:0]: Peripheral Output Function is Assigned to S1RP172 Output Pin bits(1) (see Table 4-31 for peripheral function numbers) Note 1: These are virtual output ports.  2017-2019 Microchip Technology Inc. DS70005319D-page 375 dsPIC33CH128MP508 FAMILY REGISTER 4-83: RPOR22: PERIPHERAL PIN SELECT OUTPUT REGISTER 22 U-0 U-0 R/W-0 — — RP175R5(1) R/W-0 R/W-0 RP175R4(1) RP175R3(1) R/W-0 R/W-0 R/W-0 RP175R2(1) RP175R1(1) RP175R0(1) bit 15 bit 8 U-0 U-0 R/W-0 — — RP174R5(1) R/W-0 R/W-0 RP174R4(1) RP174R3(1) R/W-0 R/W-0 R/W-0 RP174R2(1) RP174R1(1) RP174R0(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RP175R[5:0]: Peripheral Output Function is Assigned to S1RP175 Output Pin bits(1) (see Table 4-31 for peripheral function numbers) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 RP174R[5:0]: Peripheral Output Function is Assigned to S1RP174 Output Pin bits(1) (see Table 4-31 for peripheral function numbers) Note 1: These are virtual output ports. DS70005319D-page 376  2017-2019 Microchip Technology Inc.  2017-2019 Microchip Technology Inc. TABLE 4-33: Register PORTA REGISTER SUMMARY Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 ANSELA — — — — — — — — — — — TRISA — — — — — — — — — — — PORTA — — — — — — — — — — — RA[4:0] LATA — — — — — — — — — — — LATA[4:0] ODCA — — — — — — — — — — — ODCA[4:0] CNPUA — — — — — — — — — — — CNPUA[4:0] CNPDA — — — — — — — — — — — CNCONA ON — — — CNSTYLE — — — — — — CNEN0A — — — — — — — — — — — CNEN0A[4:0] CNSTATA — — — — — — — — — — — CNSTATA[4:0] CNEN1A — — — — — — — — — — — CNEN1A[4:0] CNFA — — — — — — — — — — — CNFA[4:0] Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 ANSELB — — — — — — — TRISB Bit 1 ANSELA[3:1] Bit 0 — TRISA[4:0] CNPDA[4:0] — — — — — Bit 8 Bit 7 ANSELB[8:7] Bit 6 Bit 5 — — — — Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 — — ANSELB[4:0] TRISB[15:0] PORTB RB[15:0] LATB LATB[15:0] ODCB ODCB[15:0] CNPUB CNPUB[15:0] CNPDB CNPDB[15:0] ON — — — CNSTYLE — — — CNEN0B CNEN0B[15:0] CNSTAT B CNSTATB[15:0] CNEN1B CNEN1B[15:0] DS70005319D-page 377 CNFB Bit 2 PORTB REGISTER SUMMARY Register CNCONB Bit 3 CNFB[15:0] — — — — dsPIC33CH128MP508 FAMILY TABLE 4-34: Bit 4 Register ANSELC PORTC REGISTER SUMMARY Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 — — — — — — — TRISC Bit 7 Bit 5 Bit 4 ANSELC[7:6] — — — — — — — — Bit 0 ANSELC[3:0] CNPUC[15:0] CNPDC CNPDC[15:0] ON — — — CNSTYLE — — — CNEN0C CNEN0C[15:0] CNSTATC CNSTATC[15:0] CNEN1C CNEN1C[15:0] CNFC — — — CNFC[15:0] TABLE 4-36: Bit 15 PORTD REGISTER SUMMARY Bit 14 Bit 13 — Bit 12 Bit 11 Bit 10 ANSELD[14:10] Bit 9 — TRISD Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 — — — — — — — — — — — — — — — — — RD[15:0] LATD LATD[15:0] ODCD ODCD[15:0] CNPUD CNPUD[15:0] CNPDD  2017-2019 Microchip Technology Inc. Bit 8 TRISD[15:0] PORTD CNPDD[15:0] ON — — — CNSTYLE — — — CNEN0D CNEN0D[15:0] CNSTATD CNSTATD[15:0] CNEN1D CNEN1D[15:0] CNFD Bit 1 ODCC[15:0] CNPUC CNCOND Bit 2 LATC[15:0] ODCC ANSELD Bit 3 RC[15:0] LATC Register Bit 6 TRISC[15:0] PORTC CNCONC Bit 8 CNFD[15:0] dsPIC33CH128MP508 FAMILY DS70005319D-page 378 TABLE 4-35:  2017-2019 Microchip Technology Inc. TABLE 4-37: Register ANSLE PORTE REGISTER SUMMARY Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 — — — — — — — TRISE Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 — — ANSELE6 — — — — — — — — — — — — — — TRISE[15:0] PORTE RE[15:0] LATE LATE[15:0] ODCE ODCE[15:0] CNPUE CNPUE[15:0] CNPDE CNCONE Bit 8 CNPDE[15:0] ON — — — CNSTYLE — — — CNEN0E CNEN0E[15:0] CNSTAT E CNSTATE[15:0] CNEN1E CNEN1E[15:0] CNFE CNFE[15:0] dsPIC33CH128MP508 FAMILY DS70005319D-page 379 dsPIC33CH128MP508 FAMILY 4.7 High-Speed, 12-Bit Analog-to-Digital Converter (Slave ADC) Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “12-Bit High-Speed, Multiple SARs A/D Converter (ADC)” (www.microchip.com/DS70005213) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). 2: This section describes the Slave ADC. dsPIC33CH128MP508S1 devices have a high-speed, 12-bit Analog-to-Digital Converter (ADC) that features a low conversion latency, high resolution and oversampling capabilities to improve performance in AC/DC, DC/DC power converters. The Slave implements the ADC with three SAR cores, two dedicated and one shared. 4.7.1 SLAVE ADC FEATURES OVERVIEW The High-Speed, 12-Bit Multiple SARs Analog-to-Digital Converter (ADC) includes the following features: • Three ADC Cores: Two Dedicated Cores and One Shared (common) Core • User-Configurable Resolution of up to 12 Bits for each Core • Up to 3.5 Msps Conversion Rate per Channel at 12-Bit Resolution • Low-Latency Conversion • Up to 20 Analog Input Channels, with a Separate 16-Bit Conversion Result Register for each Input • Conversion Result can be Formatted as Unsigned or Signed Data, on a per Channel Basis, for All Channels DS70005319D-page 380 • Simultaneous Sampling of up to Three Analog Inputs • Channel Scan Capability • Multiple Conversion Trigger Options for each Core, including: - PWM triggers from Master and Slave CPU cores - SCCP modules triggers - CLC modules triggers - External pin trigger event (ADTRG31) - Software trigger • Four Integrated Digital Comparators with Dedicated Interrupts: - Multiple comparison options - Assignable to specific analog inputs • Four Oversampling Filters with Dedicated Interrupts: - Provide increased resolution - Assignable to a specific analog input The module consists of three independent SAR ADC cores. Simplified block diagrams of the Multiple SARs 12-Bit ADC are shown in Figure 4-18 and Figure 4-19. The analog inputs (channels) are connected through multiplexers and switches to the Sample-and-Hold (S&H) circuit of each ADC core. The core uses the channel information (the output format, the Measurement mode and the input number) to process the analog sample. When conversion is complete, the result is stored in the result buffer for the specific analog input, and passed to the digital filter and digital comparator if they were configured to use data from this particular channel. The ADC module can sample up to three inputs at a time (two inputs from the dedicated SAR cores and one from the shared SAR core). If multiple ADC inputs request conversion on the shared core, the module will convert them in a sequential manner, starting with the lowest order input. The ADC provides each analog input the ability to specify its own trigger source. This capability allows the ADC to sample and convert analog inputs that are associated with PWM generators operating on independent time bases.  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 4-18: ADC MODULE BLOCK DIAGRAM AVDD AVSS Voltage Reference (REFSEL[2:0]) S1AN0 Reference S1ANA0 SPGA1(1) S1ANC0 Dedicated ADC Core 0(2) Output Data Digital Comparator 0 Clock Digital Comparator 1 S1ANN0 Digital Comparator 2 S1AN1 SPGA2(1) Digital Comparator 3 Reference S1ANA1 Dedicated ADC Core 1(2) S1ANC1 Clock Reference S1AN3-S1AN17 S1AN18 Temperature Sensor (S1AN19) Band Gap 1.2V (S1AN20) Shared ADC Core ADCMP1 Interrupt ADCMP2 Interrupt ADCMP3 Interrupt Output Data S1ANN1 SPGA3(1) (S1AN2) ADCMP0 Interrupt Output Data Digital Filter 0 ADFL0DAT Digital Filter 1 ADFL1DAT Digital Filter 2 ADFL2DAT Digital Filter 3 ADFL3DAT ADFLTR0 Interrupt ADFLTR1 Interrupt ADFLTR2 Interrupt ADFLTR3 Interrupt Clock ADCBUF0 ADCBUF1 ADCAN0 Interrupt ADCAN1 Interrupt Divider (CLKDIV[5:0]) ADCBUF20 ADCAN20 Interrupt Clock Selection (CLKSEL[1:0]) Fvco/4 AFVCODIV FP (FOSC/2) FOSC Note 1: SPGA1, SPGA2, SPGA3 and Band Gap Reference (VBG) are internal analog inputs and are not available on device pins. 2: If the dedicated core uses an alternate channel, then shared core function cannot be used.  2017-2019 Microchip Technology Inc. DS70005319D-page 381 dsPIC33CH128MP508 FAMILY FIGURE 4-19: ADC SHARED CORE BLOCK DIAGRAM SPGA3 (AN2) S1AN3 + S1AN18 Band Gap 1.2V (AN20) Shared Sampleand-Hold Analog Channel Number from Current Trigger Reference 12-Bit SAR ADC Temperature Sensor (AN19) Output Data Clock ADC Core Clock Divider – SHRADCS[6:0] SHRSAMC[9:0] Sampling Time AVSS FIGURE 4-20: DEDICATED ADC CORE ANx Analog Input Pins Positive Input Selection (CxCHS bits) From Other Analog Modules “+” Reference Sampleand-Hold 12-Bit SAR ADC Output Data ANNx Negative Input Selection (DIFFx bit) AVSS 4.7.2 TEMPERATURE SENSOR The ADC channel, S1AN19, is connected to a forward biased diode; it can be used to measure die temperature. This diode provides an output with a temperature coefficient of approximately -1.5 mV/C that can be monitored by the ADC. To get the exact gain and offset numbers, two-point temperature calibration is recommended. 4.7.3 ANALOG-TO-DIGITAL CONVERTER RESOURCES Many useful resources are provided on the main product page of the Microchip website for the devices listed in this data sheet. This product page contains the latest updates and additional information. DS70005319D-page 382 “–” Trigger Stops Sampling 4.7.3.1 ADC Core Clock Divider (ADCS bits) Clock Key Resources • “12-Bit High-Speed, Multiple SARs A/D Converter (ADC)” (www.microchip.com/ DS70005213) in the “dsPIC33/PIC24 Family Reference Manual” • Code Samples • Application Notes • Software Libraries • Webinars • All Related “dsPIC33/PIC24 Family Reference Manual” Sections • Development Tools  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 4.7.4 ADC CONTROL/STATUS REGISTERS REGISTER 4-84: ADCON1L: ADC CONTROL REGISTER 1 LOW R/W-0 U-0 R/W-0 U-0 r-0 U-0 U-0 U-0 ADON(1) — ADSIDL — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 ADON: ADC Enable bit(1) 1 = ADC module is enabled 0 = ADC module is off bit 14 Unimplemented: Read as ‘0’ bit 13 ADSIDL: ADC Stop in Idle Mode bit 1 = Discontinues module operation when device enters Idle mode 0 = Continues module operation in Idle mode bit 12 Unimplemented: Read as ‘0’ bit 11 Reserved: Maintain as ‘0’ bit 10-0 Unimplemented: Read as ‘0’ Note 1: x = Bit is unknown Set the ADON bit only after the ADC module has been configured. Changing ADC Configuration bits when ADON = 1 will result in unpredictable behavior.  2017-2019 Microchip Technology Inc. DS70005319D-page 383 dsPIC33CH128MP508 FAMILY REGISTER 4-85: ADCON1H: ADC CONTROL REGISTER 1 HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-0 R/W-1 R/W-1 U-0 U-0 U-0 U-0 U-0 FORM SHRRES1 SHRRES0 — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-8 Unimplemented: Read as ‘0’ bit 7 FORM: Fractional Data Output Format bit 1 = Fractional 0 = Integer bit 6-5 SHRRES[1:0]: Shared ADC Core Resolution Selection bits 11 = 12-bit resolution 10 = 10-bit resolution 01 = 8-bit resolution 00 = 6-bit resolution bit 4-0 Unimplemented: Read as ‘0’ DS70005319D-page 384 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-86: ADCON2L: ADC CONTROL REGISTER 2 LOW R/W-0 R/W-0 U-0 R/W-0 R/W-0 REFCIE REFERCIE — EIEN PTGEN R/W-0 R/W-0 R/W-0 SHREISEL2(1) SHREISEL1(1) SHREISEL0(1) bit 15 bit 8 U-0 R/W-0 R/W-0 — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SHRADCS[6:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 REFCIE: Band Gap and Reference Voltage Ready Common Interrupt Enable bit 1 = Common interrupt will be generated when the band gap will become ready 0 = Common interrupt is disabled for the band gap ready event bit 14 REFERCIE: Band Gap or Reference Voltage Error Common Interrupt Enable bit 1 = Common interrupt will be generated when a band gap or reference voltage error is detected 0 = Common interrupt is disabled for the band gap and reference voltage error event bit 13 Unimplemented: Read as ‘0’ bit 12 EIEN: Early Interrupts Enable bit 1 = The early interrupt feature is enabled for the input channel interrupts (when the EISTATx flag is set) 0 = The individual interrupts are generated when conversion is done (when the ANxRDY flag is set) bit 11 PTGEN: External Conversion Request Interface bit Setting this bit will enable the PTG to request conversion of an ADC input. bit 10-8 SHREISEL[2:0]: Shared Core Early Interrupt Time Selection bits(1) 111 = Early interrupt is set and interrupt is generated 8 TADCORE clocks prior to when the data are ready 110 = Early interrupt is set and interrupt is generated 7 TADCORE clocks prior to when the data are ready 101 = Early interrupt is set and interrupt is generated 6 TADCORE clocks prior to when the data are ready 100 = Early interrupt is set and interrupt is generated 5 TADCORE clocks prior to when the data are ready 011 = Early interrupt is set and interrupt is generated 4 TADCORE clocks prior to when the data are ready 010 = Early interrupt is set and interrupt is generated 3 TADCORE clocks prior to when the data are ready 001 = Early interrupt is set and interrupt is generated 2 TADCORE clocks prior to when the data are ready 000 = Early interrupt is set and interrupt is generated 1 TADCORE clock prior to when the data are ready bit 7 Unimplemented: Read as ‘0’ bit 6-0 SHRADCS[6:0]: Shared ADC Core Input Clock Divider bits These bits determine the number of TCORESRC (Source Clock Periods) for one shared TADCORE (Core Clock Period). 1111111 = 254 Source Clock Periods ... 0000011 = 6 Source Clock Periods 0000010 = 4 Source Clock Periods 0000001 = 2 Source Clock Periods 0000000 = 2 Source Clock Periods Note 1: For the 6-bit shared ADC core resolution (SHRRES[1:0] = 00), the SHREISEL[2:0] settings, from ‘100’ to ‘111’, are not valid and should not be used. For the 8-bit shared ADC core resolution (SHRRES[1:0] = 01), the SHREISEL[2:0] settings, ‘110’ and ‘111’, are not valid and should not be used.  2017-2019 Microchip Technology Inc. DS70005319D-page 385 dsPIC33CH128MP508 FAMILY REGISTER 4-87: ADCON2H: ADC CONTROL REGISTER 2 HIGH HSC/R-0 HSC/R-0 U-0 r-0 r-0 r-0 REFRDY REFERR — r r r R/W-0 R/W-0 SHRSAMC[9:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SHRSAMC[7:0] bit 7 bit 0 Legend: r = Reserved bit U = Unimplemented bit, read as ‘0’ R = Readable bit W = Writable bit HSC = Hardware Settable/Clearable bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 REFRDY: Band Gap and Reference Voltage Ready Flag bit 1 = Band gap is ready 0 = Band gap is not ready bit 14 REFERR: Band Gap or Reference Voltage Error Flag bit 1 = Band gap was removed after the ADC module was enabled (ADON = 1) 0 = No band gap error was detected bit 13 Unimplemented: Read as ‘0’ bit 12-10 Reserved: Maintain as ‘0’ bit 9-0 SHRSAMC[9:0]: Shared ADC Core Sample Time Selection bits These bits specify the number of shared ADC Core Clock Periods (TADCORE) for the shared ADC core sample time. 1111111111 = 1025 TADCORE ... 0000000001 = 3 TADCORE 0000000000 = 2 TADCORE DS70005319D-page 386  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-88: ADCON3L: ADC CONTROL REGISTER 3 LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 HSC/R-0 R/W-0 HSC/R-0 REFSEL2 REFSEL1 REFSEL0 SUSPEND SUSPCIE SUSPRDY SHRSAMP CNVRTCH bit 15 bit 8 R/W-0 HSC/R-0 SWLCTRG SWCTRG R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: U = Unimplemented bit, read as ‘0’ R = Readable bit W = Writable bit HSC = Hardware Settable/Clearable bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-13 R/W-0 CNVCHSEL5 CNVCHSEL4 CNVCHSEL3 CNVCHSEL2 CNVCHSEL1 CNVCHSEL0 x = Bit is unknown REFSEL[2:0]: ADC Reference Voltage Selection bits Value VREFH VREFL 000 AVDD AVSS 001-111 = Unimplemented: Do not use bit 12 SUSPEND: All ADC Core Triggers Disable bit 1 = All new trigger events for all ADC cores are disabled 0 = All ADC cores can be triggered bit 11 SUSPCIE: Suspend All ADC Cores Common Interrupt Enable bit 1 = Common interrupt will be generated when ADC core triggers are suspended (SUSPEND bit = 1) and all previous conversions are finished (SUSPRDY bit becomes set) 0 = Common interrupt is not generated for suspend ADC cores event bit 10 SUSPRDY: All ADC Cores Suspended Flag bit 1 = All ADC cores are suspended (SUSPEND bit = 1) and have no conversions in progress 0 = ADC cores have previous conversions in progress bit 9 SHRSAMP: Shared ADC Core Sampling Direct Control bit This bit should be used with the individual channel conversion trigger controlled by the CNVRTCH bit. It connects an analog input, specified by the CNVCHSEL[5:0] bits, to the shared ADC core and allows extending the sampling time. This bit is not controlled by hardware and must be cleared before the conversion starts (setting CNVRTCH to ‘1’). 1 = Shared ADC core samples an analog input specified by the CNVCHSEL[5:0] bits 0 = Sampling is controlled by the shared ADC core hardware bit 8 CNVRTCH: Software Individual Channel Conversion Trigger bit 1 = Single trigger is generated for an analog input specified by the CNVCHSEL[5:0] bits; when the bit is set, it is automatically cleared by hardware on the next instruction cycle 0 = Next individual channel conversion trigger can be generated bit 7 SWLCTRG: Software Level-Sensitive Common Trigger bit 1 = Triggers are continuously generated for all channels with the software, level-sensitive common trigger selected as a source in the ADTRIGnL and ADTRIGnH registers 0 = No software, level-sensitive common triggers are generated bit 6 SWCTRG: Software Common Trigger bit 1 = Single trigger is generated for all channels with the software; common trigger selected as a source in the ADTRIGnL and ADTRIGnH registers; when the bit is set, it is automatically cleared by hardware on the next instruction cycle 0 = Ready to generate the next software common trigger bit 5-0 CNVCHSEL [5:0]: Channel Number Selection for Software Individual Channel Conversion Trigger bits These bits define a channel to be converted when the CNVRTCH bit is set.  2017-2019 Microchip Technology Inc. DS70005319D-page 387 dsPIC33CH128MP508 FAMILY REGISTER 4-89: ADCON3H: ADC CONTROL REGISTER 3 HIGH R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CLKSEL1 CLKSEL0 CLKDIV5 CLKDIV4 CLKDIV3 CLKDIV2 CLKDIV1 CLKDIV0 bit 15 bit 8 R/W-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 SHREN — — — — — C1EN C0EN bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 CLKSEL[1:0]: ADC Module Clock Source Selection bits 11 = FVCO/4 10 = AFVCODIV 01 = FOSC 00 = FP (FOSC/2) bit 13-8 CLKDIV[5:0]: ADC Module Clock Source Divider bits The divider forms a TCORESRC clock used by all ADC cores (shared and dedicated) from the TSRC ADC module clock source selected by the CLKSEL[1:0] bits. Then, each ADC core individually divides the TCORESRC clock to get a core-specific TADCORE clock using the ADCS[6:0] bits in the ADCORExH register or the SHRADCS[6:0] bits in the ADCON2L register. 111111 = 64 Source Clock Periods ... 000011 = 4 Source Clock Periods 000010 = 3 Source Clock Periods 000001 = 2 Source Clock Periods 000000 = 1 Source Clock Period bit 7 SHREN: Shared ADC Core Enable bit 1 = Shared ADC core is enabled 0 = Shared ADC core is disabled bit 6-2 Unimplemented: Read as ‘0’ bit 1 C1EN: Dedicated ADC Core 1 Enable bits 1 = Dedicated ADC Core 1 is enabled 0 = Dedicated ADC Core 1 is disabled bit 0 C0EN: Dedicated ADC Core 0 Enable bits 1 = Dedicated ADC Core 0 is enabled 0 = Dedicated ADC Core 0 is disabled DS70005319D-page 388  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-90: ADCON4L: ADC CONTROL REGISTER 4 LOW U-0 U-0 U-0 U-0 U-0 U-0 r-0 r-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 — — — — — — SAMC1EN SAMC0EN bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-10 Unimplemented: Read as ‘0’ bit 9-8 Reserved: Must be written as ‘0’ bit 7-2 Unimplemented: Read as ‘0’ bit 1 SAMC1EN: Dedicated ADC Core 1 Conversion Delay Enable bit 1 = After trigger, the conversion will be delayed and the ADC core will continue sampling during the time specified by the SAMC[9:0] bits in the ADCORE1L register 0 = After trigger, the sampling will be stopped immediately and the conversion will be started on the next core clock cycle bit 0 SAMC0EN: Dedicated ADC Core 0 Conversion Delay Enable bit 1 = After trigger, the conversion will be delayed and the ADC core will continue sampling during the time specified by the SAMC[9:0] bits in the ADCORE0L register 0 = After trigger, the sampling will be stopped immediately and the conversion will be started on the next core clock cycle  2017-2019 Microchip Technology Inc. DS70005319D-page 389 dsPIC33CH128MP508 FAMILY REGISTER 4-91: ADCON4H: ADC CONTROL REGISTER 4 HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — — C1CHS1 C1CHS0 C0CHS1 C0CHS0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-4 Unimplemented: Read as ‘0’ bit 3-2 C1CHS[1:0]: Dedicated ADC Core 1 Input Channel Selection bits 11 = S1ANC1 10 = SPGA2 01 = S1ANA1 00 = S1AN1 bit 1-0 C0CHS[1:0]: Dedicated ADC Core 0 Input Channel Selection bits 11 = S1ANC0 10 = SPGA1 01 = S1ANA0 00 = S1AN0 DS70005319D-page 390 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-92: ADCON5L: ADC CONTROL REGISTER 5 LOW HSC/R-0 U-0 U-0 U-0 U-0 U-0 HSC/R-0 HSC/R-0 SHRRDY — — — — — C1RDY C0RDY bit 15 bit 8 R/W-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 SHRPWR — — — — — C1PWR C0PWR bit 7 bit 0 Legend: U = Unimplemented bit, read as ‘0’ R = Readable bit W = Writable bit HSC = Hardware Settable/Clearable bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 SHRRDY: Shared ADC Core Ready Flag bit 1 = ADC core is powered and ready for operation 0 = ADC core is not ready for operation bit 14-10 Unimplemented: Read as ‘0’ bit 9 C1RDY: Dedicated ADC Core 1 Ready Flag bit 1 = ADC Core 1 is powered and ready for operation 0 = ADC Core 1 is not ready for operation bit 8 C0RDY: Dedicated ADC Core 0 Ready Flag bit 1 = ADC Core 0 is powered and ready for operation 0 = ADC Core 0 is not ready for operation bit 7 SHRPWR: Shared ADC Core Power Enable bit 1 = ADC core is powered 0 = ADC core is off bit 6-2 Unimplemented: Read as ‘0’ bit 1 C1PWR: Dedicated ADC Core 1 Power Enable bit 1 = ADC Core 1 is powered 0 = ADC Core 1 is off bit 0 C0PWR: Dedicated ADC Core 0 Power Enable bit 1 = ADC Core 0 is powered 0 = ADC Core 0 is off  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 391 dsPIC33CH128MP508 FAMILY REGISTER 4-93: ADCON5H: ADC CONTROL REGISTER 5 HIGH U-0 U-0 U-0 U-0 — — — — R/W-0 R/W-0 R/W-0 R/W-0 WARMTIME[3:0] bit 15 bit 8 R/W-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 SHRCIE — — — — — C1CIE C0CIE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-12 Unimplemented: Read as ‘0’ bit 11-8 WARMTIME[3:0]: ADC Dedicated Core x Power-up Delay bits These bits determine the power-up delay in the number of the Core Source Clock Periods (TCORESRC) for all ADC cores. 1111 = 32768 Source Clock Periods 1110 = 16384 Source Clock Periods 1101 = 8192 Source Clock Periods 1100 = 4096 Source Clock Periods 1011 = 2048 Source Clock Periods 1010 = 1024 Source Clock Periods 1001 = 512 Source Clock Periods 1000 = 256 Source Clock Periods 0111 = 128 Source Clock Periods 0110 = 64 Source Clock Periods 0101 = 32 Source Clock Periods 0100 = 16 Source Clock Periods 00xx = 16 Source Clock Periods bit 7 SHRCIE: Shared ADC Core Ready Common Interrupt Enable bit 1 = Common interrupt will be generated when ADC core is powered and ready for operation 0 = Common interrupt is disabled for an ADC core ready event bit 6-2 Unimplemented: Read as ‘0’ bit 1 C1CIE: Dedicated ADC Core 1 Ready Common Interrupt Enable bit 1 = Common interrupt will be generated when ADC Core 1 is powered and ready for operation 0 = Common interrupt is disabled for an ADC Core 1 ready event bit 0 C0CIE: Dedicated ADC Core 0 Ready Common Interrupt Enable bit 1 = Common interrupt will be generated when ADC Core 0 is powered and ready for operation 0 = Common interrupt is disabled for an ADC Core 0 ready event DS70005319D-page 392  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-94: ADCORExL: DEDICATED ADC CORE x CONTROL REGISTER LOW (x = 0 TO 1) U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — R/W-0 R/W-0 SAMC[9:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SAMC[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-10 Unimplemented: Read as ‘0’ bit 9-0 SAMC[9:0]: Dedicated ADC Core x Conversion Delay Selection bits These bits determine the time between the trigger event and the start of conversion in the number of the Core Clock Periods (TADCORE). During this time, the ADC Core x still continues sampling. This feature is enabled by the SAMCxEN bits in the ADCON4L register. 1111111111 = 1025 TADCORE ... 0000000001 = 3 TADCORE 0000000000 = 2 TADCORE  2017-2019 Microchip Technology Inc. DS70005319D-page 393 dsPIC33CH128MP508 FAMILY REGISTER 4-95: ADCORExH: DEDICATED ADC CORE x CONTROL REGISTER HIGH (x = 0 TO 1) U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — EISEL2 EISEL1 EISEL0 RES1 RES2 bit 15 U-0 bit 8 R/W-0 R/W-0 — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ADCS[6:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-13 Unimplemented: Read as ‘0’ bit 12-10 EISEL[2:0]: ADC Core x Early Interrupt Time Selection bits 111 = Early interrupt is set and an interrupt is generated 8 TADCORE clocks prior to when the data are ready 110 = Early interrupt is set and an interrupt is generated 7 TADCORE clocks prior to when the data are ready 101 = Early interrupt is set and an interrupt is generated 6 TADCORE clocks prior to when the data are ready 100 = Early interrupt is set and an interrupt is generated 5 TADCORE clocks prior to when the data are ready 011 = Early interrupt is set and an interrupt is generated 4 TADCORE clocks prior to when the data are ready 010 = Early interrupt is set and an interrupt is generated 3 TADCORE clocks prior to when the data are ready 001 = Early interrupt is set and an interrupt is generated 2 TADCORE clocks prior to when the data are ready 000 = Early interrupt is set and an interrupt is generated 1 TADCORE clock prior to when the data are ready bit 9-8 RES[1:0]: ADC Core x Resolution Selection bits 11 = 12-bit resolution 10 = 10-bit resolution 01 = 8-bit resolution(1) 00 = 6-bit resolution(1) bit 7 Unimplemented: Read as ‘0’ bit 6-0 ADCS[6:0]: ADC Core x Input Clock Divider bits These bits determine the number of Source Clock Periods (TCORESRC) for one Core Clock Period (TADCORE). 1111111 = 254 Source Clock Periods ... 0000011 = 6 Source Clock Periods 0000010 = 4 Source Clock Periods 0000001 = 2 Source Clock Periods 0000000 = 2 Source Clock Periods Note 1: For the 6-bit ADC core resolution (RES[1:0] = 00), the EISEL[2:0] bits settings, from ‘100’ to ‘111’, are not valid and should not be used. For the 8-bit ADC core resolution (RES[1:0] = 01), the EISEL[2:0] bits settings, ‘110’ and ‘111’, are not valid and should not be used. DS70005319D-page 394  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-96: R/W-0 ADLVLTRGL: ADC LEVEL-SENSITIVE TRIGGER CONTROL REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 LVLEN[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 LVLEN[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown LVLEN[15:0]: Level Trigger for Corresponding Analog Input Enable bits 1 = Input trigger is level-sensitive 0 = Input trigger is edge-sensitive REGISTER 4-97: ADLVLTRGH: ADC LEVEL-SENSITIVE TRIGGER CONTROL REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 LVLEN[20:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-5 Unimplemented: Read as ‘0’ bit 4-0 LVLEN[20:16]: Level Trigger for Corresponding Analog Input Enable bits 1 = Input trigger is level-sensitive 0 = Input trigger is edge-sensitive  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 395 dsPIC33CH128MP508 FAMILY REGISTER 4-98: R/W-0 ADEIEL: ADC EARLY INTERRUPT ENABLE REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 EIEN[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 EIEN[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown EIEN[15:0]: Early Interrupt Enable for Corresponding Analog Inputs bits 1 = Early interrupt is enabled for the channel 0 = Early interrupt is disabled for the channel REGISTER 4-99: ADEIEH: ADC EARLY INTERRUPT ENABLE REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 EIEN[20:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-5 Unimplemented: Read as ‘0’ bit 4-0 EIEN[20:16]: Early Interrupt Enable for Corresponding Analog Inputs bits 1 = Early interrupt is enabled for the channel 0 = Early interrupt is disabled for the channel DS70005319D-page 396  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-100: ADEISTATL: ADC EARLY INTERRUPT STATUS REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 EISTAT[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 EISTAT[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown EISTAT[15:0]: Early Interrupt Status for Corresponding Analog Inputs bits 1 = Early interrupt was generated 0 = Early interrupt was not generated since the last ADCBUFx read REGISTER 4-101: ADEISTATH: ADC EARLY INTERRUPT STATUS REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 EISTAT[20:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-5 Unimplemented: Read as ‘0’ bit 4-0 EISTAT[20:16]: Early Interrupt Status for Corresponding Analog Inputs bits 1 = Early interrupt was generated 0 = Early interrupt was not generated since the last ADCBUFx read  2017-2019 Microchip Technology Inc. DS70005319D-page 397 dsPIC33CH128MP508 FAMILY REGISTER 4-102: ADMOD0L: ADC INPUT MODE CONTROL REGISTER 0 LOW U-0 R/W-0 U-0 R/W-0 U-0 R/W-0 U-0 R/W-0 — SIGN7 — SIGN6 — SIGN5 — SIGN4 bit 15 bit 8 U-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — SIGN3 — SIGN2 DIFF1 SIGN1 DIFF0 SIGN0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-5 (odd) x = Bit is unknown Unimplemented: Read as ‘0’ bit 14-0 (even) SIGNn (n = 7 to 0): Output Data Sign for Corresponding Analog Inputs bits 1 = Channel output data are signed 0 = Channel output data are unsigned bit 3-1 (odd) DIFFn (n = 1 to 0): Differential-Mode for Corresponding Analog Inputs bits 1 = Channel is differential 0 = Channel is single-ended REGISTER 4-103: ADMOD0H: ADC INPUT MODE CONTROL REGISTER 0 HIGH U-0 R/W-0 U-0 R/W-0 U-0 R/W-0 U-0 R/W-0 — SIGN15 — SIGN14 — SIGN13 — SIGN12 bit 15 bit 8 U-0 R/W-0 U-0 R/W-0 U-0 R/W-0 U-0 R/W-0 — SIGN11 — SIGN10 — SIGN9 — SIGN8 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-1 (odd) x = Bit is unknown Unimplemented: Read as ‘0’ bit 14-0 (even) SIGNn (n = 15 to 8): Output Data Sign for Corresponding Analog Input bits 1 = Channel output data are signed 0 = Channel output data are unsigned DS70005319D-page 398  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-104: ADMOD1L: ADC INPUT MODE CONTROL REGISTER 1 LOW U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — — SIGN20 bit 15 bit 8 U-0 R/W-0 U-0 R/W-0 U-0 R/W-0 U-0 R/W-0 — SIGN19 — SIGN18 — SIGN17 — SIGN16 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-9 Unimplemented: Read as ‘0’ bit 7-1 (odd) Unimplemented: Read as ‘0’ bit 8-0 (even) SIGNn (n = 20 to 16): Output Data Sign for Corresponding Analog Input bits 1 = Channel output data are signed 0 = Channel output data are unsigned  2017-2019 Microchip Technology Inc. DS70005319D-page 399 dsPIC33CH128MP508 FAMILY REGISTER 4-105: ADIEL: ADC INTERRUPT ENABLE REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 IE[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 IE[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown IE[15:0]: Common Interrupt Enable bits 1 = Common and individual interrupts are enabled for the corresponding channel 0 = Common and individual interrupts are disabled for the corresponding channel REGISTER 4-106: ADIEH: ADC INTERRUPT ENABLE REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 IE[20:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-5 Unimplemented: Read as ‘0’ bit 4-0 IE[20:16]: Common Interrupt Enable bits 1 = Common and individual interrupts are enabled for the corresponding channel 0 = Common and individual interrupts are disabled for the corresponding channel DS70005319D-page 400  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-107: ADSTATL: ADC DATA READY STATUS REGISTER LOW HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 AN[15:8]RDY bit 15 HSC/R-0 bit 8 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 AN[7:0]RDY bit 7 bit 0 Legend: U = Unimplemented bit, read as ‘0’ R = Readable bit W = Writable bit HSC = Hardware Settable/Clearable bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown AN[15:0]RDY: Common Interrupt Enable for Corresponding Analog Inputs bits 1 = Channel conversion result is ready in the corresponding ADCBUFx register 0 = Channel conversion result is not ready REGISTER 4-108: ADSTATH: ADC DATA READY STATUS REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 — — — HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 AN[20:16]RDY bit 7 bit 0 Legend: U = Unimplemented bit, read as ‘0’ R = Readable bit W = Writable bit HSC = Hardware Settable/Clearable bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-5 Unimplemented: Read as ‘0’ bit 4-0 AN[20:16]RDY: Common Interrupt Enable for Corresponding Analog Inputs bits 1 = Channel conversion result is ready in the corresponding ADCBUFx register 0 = Channel conversion result is not ready  2017-2019 Microchip Technology Inc. DS70005319D-page 401 dsPIC33CH128MP508 FAMILY REGISTER 4-109: ADTRIGnL/ADTRIGnH: ADC CHANNEL TRIGGER n(x) SELECTION REGISTERS LOW AND HIGH (x = 0 TO 19; n = 0 TO 4) U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TRGSRC(x+1)[4:0] bit 15 bit 8 U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TRGSRCx[4:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-13 Unimplemented: Read as ‘0’ bit 12-8 TRGSRC(x+1)[4:0]: Trigger Source Selection for Corresponding Analog Inputs bits (TRGSRC1 to TRGSRC19 – Odd) 11111 = ADTRG31 (PPS input) 11110 = Master PTG 11101 = Slave CLC1 11100 = Master CLC1 11011 = Reserved 11010 = Reserved 11001 = Master PWM3 Trigger 2 11000 = Master PWM1 Trigger 2 10111 = Slave SCCP4 input capture/output compare 10110 = Slave SCCP3 input capture/output compare 10101 = Slave SCCP2 input capture/output compare 10100 = Slave SCCP1 input capture/output compare 10011 = Reserved 10010 = Reserved 10001 = Reserved 10000 = Reserved 01111 = Slave PWM8 Trigger 1 01110 = Slave PWM7 Trigger 1 01101 = Slave PWM6 Trigger 1 01100 = Slave PWM5 Trigger 1 01011 = Slave PWM4 Trigger 2 01010 = Slave PWM4 Trigger 1 01001 = Slave PWM3 Trigger 2 01000 = Slave PWM3 Trigger 1 00111 = Slave PWM2 Trigger 2 00110 = Slave PWM2 Trigger 1 00101 = Slave PWM1 Trigger 2 00100 = Slave PWM1 Trigger 1 00011 = Reserved 00010 = Level software trigger 00001 = Common software trigger 00000 = No trigger is enabled bit 7-5 Unimplemented: Read as ‘0’ DS70005319D-page 402  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-109: ADTRIGnL/ADTRIGnH: ADC CHANNEL TRIGGER n(x) SELECTION REGISTERS LOW AND HIGH (x = 0 TO 19; n = 0 TO 4) (CONTINUED) bit 4-0 TRGSRCx[4:0]: Common Interrupt Enable for Corresponding Analog Inputs bits (TRGSRC0 to TRGSRC20 – Even) 11111 = ADTRG31 (PPS input) 11110 = Master PTG 11101 = Slave CLC1 11100 = Master CLC1 11011 = Reserved 11010 = Reserved 11001 = Master PWM3 Trigger 2 11000 = Master PWM1 Trigger 2 10111 = Slave SCCP4 input capture/output compare 10110 = Slave SCCP3 input capture/output compare 10101 = Slave SCCP2 input capture/output compare 10100 = Slave SCCP1 input capture/output compare 10011 = Reserved 10010 = Reserved 10001 = Reserved 10000 = Reserved 01111 = Slave PWM8 Trigger 1 01110 = Slave PWM7 Trigger 1 01101 = Slave PWM6 Trigger 1 01100 = Slave PWM5 Trigger 1 01011 = Slave PWM4 Trigger 2 01010 = Slave PWM4 Trigger 1 01001 = Slave PWM3 Trigger 2 01000 = Slave PWM3 Trigger 1 00111 = Slave PWM2 Trigger 2 00110 = Slave PWM2 Trigger 1 00101 = Slave PWM1 Trigger 2 00100 = Slave PWM1 Trigger 1 00011 = Reserved 00010 = Level software trigger 00001 = Common software trigger 00000 = No trigger is enabled  2017-2019 Microchip Technology Inc. DS70005319D-page 403 dsPIC33CH128MP508 FAMILY REGISTER 4-110: ADCAL1H: ADC CALIBRATION REGISTER 1 HIGH HS/R/W-0 U-0 U-0 U-0 U-0 r-0 R/W-0 R/W-0 CSHRRDY — — — — — CSHREN CSHRRUN bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: HS = Hardware Settable bit r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 CSHRRDY: Shared ADC Core Calibration Status Flag bit 1 = Shared ADC core calibration is finished 0 = Shared ADC core calibration is in progress bit 14-11 Unimplemented: Read as ‘0’ bit 10 Reserved: Maintain as ‘0’ bit 9 CSHREN: Shared ADC Core Calibration Enable bit 1 = Shared ADC core calibration bits (CSHRRDY and CSHRRUN) can be accessed by software 0 = Shared ADC core calibration bits are disabled bit 8 CSHRRUN: Shared ADC Core Calibration Start bit 1 = If this bit is set by software, the shared ADC core calibration cycle is started; this bit is cleared automatically by hardware 0 = Software can start the next calibration cycle bit 7-0 Unimplemented: Read as ‘0’ DS70005319D-page 404  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-111: ADCMPxCON: ADC DIGITAL COMPARATOR x CONTROL REGISTER (x = 0, 1, 2, 3) U-0 U-0 U-0 — — — HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 CHNL[4:0] bit 15 bit 8 R/W-0 R/W-0 HC/HS/R-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CMPEN IE STAT BTWN HIHI HILO LOHI LOLO bit 7 bit 0 Legend: HC = Hardware Clearable bit U = Unimplemented bit, read as ‘0’ R = Readable bit W = Writable bit HSC = Hardware Settable/Clearable bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared HS = Hardware Settable bit bit 15-13 Unimplemented: Read as ‘0’ bit 12-8 CHNL[4:0]: Input Channel Number bits If the comparator has detected an event for a channel, this channel number is written to these bits. 11111 = Reserved ... 10101 = Reserved 10100 = Band gap, 1.2V (AN20) 10011 = Temperature sensor (AN19) 10010 = S1AN18 ... 00011 = S1AN3 00010 = S1AN2 00001 = S1AN1 00000 = S1AN0 bit 7 CMPEN: Comparator Enable bit 1 = Comparator is enabled 0 = Comparator is disabled and the STAT status bit is cleared bit 6 IE: Comparator Common ADC Interrupt Enable bit 1 = Common ADC interrupt will be generated if the comparator detects a comparison event 0 = Common ADC interrupt will not be generated for the comparator bit 5 STAT: Comparator Event Status bit This bit is cleared by hardware when the channel number is read from the CHNL[4:0] bits. 1 = A comparison event has been detected since the last read of the CHNL[4:0] bits 0 = A comparison event has not been detected since the last read of the CHNL[4:0] bits bit 4 BTWN: Between Low/High Comparator Event bit 1 = Generates a comparator event when ADCMPxLO ≤ ADCBUFx < ADCMPxHI 0 = Does not generate a digital comparator event when ADCMPxLO ≤ ADCBUFx < ADCMPxHI bit 3 HIHI: High/High Comparator Event bit 1 = Generates a digital comparator event when ADCBUFx ≥ ADCMPxHI 0 = Does not generate a digital comparator event when ADCBUFx ≥ ADCMPxHI bit 2 HILO: High/Low Comparator Event bit 1 = Generates a digital comparator event when ADCBUFx < ADCMPxHI 0 = Does not generate a digital comparator event when ADCBUFx < ADCMPxHI bit 1 LOHI: Low/High Comparator Event bit 1 = Generates a digital comparator event when ADCBUFx ≥ ADCMPxLO 0 = Does not generate a digital comparator event when ADCBUFx ≥ ADCMPxLO bit 0 LOLO: Low/Low Comparator Event bit 1 = Generates a digital comparator event when ADCBUFx < ADCMPxLO 0 = Does not generate a digital comparator event when ADCBUFx < ADCMPxLO  2017-2019 Microchip Technology Inc. DS70005319D-page 405 dsPIC33CH128MP508 FAMILY REGISTER 4-112: ADCMPxENL: ADC DIGITAL COMPARATOR x CHANNEL ENABLE REGISTER LOW (x = 0, 1, 2, 3) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CMPEN[15:8] bit 15 bit 8 R/W/0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CMPEN[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown CMPEN[15:0]: Comparator Enable for Corresponding Input Channels bits 1 = Conversion result for corresponding channel is used by the comparator 0 = Conversion result for corresponding channel is not used by the comparator REGISTER 4-113: ADCMPxENH: ADC DIGITAL COMPARATOR x CHANNEL ENABLE REGISTER HIGH (x = 0, 1, 2, 3) U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CMPEN[20:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-5 Unimplemented: Read as ‘0’ bit 4-0 CMPEN[20:16]: Comparator Enable for Corresponding Input Channels bits 1 = Conversion result for corresponding channel is used by the comparator 0 = Conversion result for corresponding channel is not used by the comparator DS70005319D-page 406  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-114: ADFLxCON: ADC DIGITAL FILTER x CONTROL REGISTER (x = 0, 1, 2, 3) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 HSC/R-0 FLEN MODE1 MODE0 OVRSAM2 OVRSAM1 OVRSAM0 IE RDY bit 15 bit 8 U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FLCHSEL[4:0] bit 7 bit 0 Legend: U = Unimplemented bit, read as ‘0’ R = Readable bit W = Writable bit HSC = Hardware Settable/Clearable bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 FLEN: Filter Enable bit 1 = Filter is enabled 0 = Filter is disabled and the RDY bit is cleared bit 14-13 MODE[1:0]: Filter Mode bits 11 = Averaging mode 10 = Reserved 01 = Reserved 00 = Oversampling mode bit 12-10 OVRSAM[2:0]: Filter Averaging/Oversampling Ratio bits If MODE[1:0] = 00: 111 = 128x (16-bit result in the ADFLxDAT register is in 12.4 format) 110 = 32x (15-bit result in the ADFLxDAT register is in 12.3 format) 101 = 8x (14-bit result in the ADFLxDAT register is in 12.2 format) 100 = 2x (13-bit result in the ADFLxDAT register is in 12.1 format) 011 = 256x (16-bit result in the ADFLxDAT register is in 12.4 format) 010 = 64x (15-bit result in the ADFLxDAT register is in 12.3 format) 001 = 16x (14-bit result in the ADFLxDAT register is in 12.2 format) 000 = 4x (13-bit result in the ADFLxDAT register is in 12.1 format) If MODE[1:0] = 11 (12-bit result in the ADFLxDAT register in all instances): 111 = 256x 110 = 128x 101 = 64x 100 = 32x 011 = 16x 110 = 8x 001 = 4x 000 = 2x bit 9 IE: Filter Common ADC Interrupt Enable bit 1 = Common ADC interrupt will be generated when the filter result will be ready 0 = Common ADC interrupt will not be generated for the filter bit 8 RDY: Oversampling Filter Data Ready Flag bit This bit is cleared by hardware when the result is read from the ADFLxDAT register. 1 = Data in the ADFLxDAT register are ready 0 = The ADFLxDAT register has been read and new data in the ADFLxDAT register are not ready bit 7-5 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. DS70005319D-page 407 dsPIC33CH128MP508 FAMILY REGISTER 4-114: ADFLxCON: ADC DIGITAL FILTER x CONTROL REGISTER (x = 0, 1, 2, 3) (CONTINUED) bit 4-0 FLCHSEL[4:0]: Oversampling Filter Input Channel Selection bits 11111 = Reserved ... 10100 = Reserved 10100 = Band gap, 1.2V (AN20) 10011 = Temperature sensor (AN19) 10010 = S1AN18 ... 00011 = S1AN3 00010 = SPGA3 (S1AN2) 00001 = S1AN1 00000 = S1AN0 DS70005319D-page 408  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 4.8 Programmable Gain Amplifier (PGA) Slave Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “Programmable Gain Amplifier (PGA)” (www.microchip.com/ DS70005146) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). be used as a ground referenced amplifier (singleended) or used with an independent ground reference point. Key features of the PGA module include: • Single-Ended or Independent Ground Reference • Selectable Gains: 4x, 8x, 16x and 32x (and 6x,12x, 24x and 48x with the 1.5 gain) • High-Gain Bandwidth • Rail-to-Rail Output Voltage • Wide Input Voltage Range Table 4-38 shows an overview of the PGA module. The dsPIC33CH128MP508S1 family devices have three Programmable Gain Amplifiers (PGA1, PGA2, PGA3). The PGA is an op amp-based, noninverting amplifier with user-programmable gains. The output of the PGA can be connected to a number of dedicated Sample-and-Hold inputs of the Analog-to-Digital Converter and/or to the high-speed analog comparator module. The PGA has four selectable gains and may FIGURE 4-21: PGA MODULE OVERVIEW(1) TABLE 4-38: Number of PGA Modules Identical (Modules) None(1) NA 3 NA Master Slave Note 1: The Slave owns the PGA module, but it is shared with the Master. PGAx MODULE BLOCK DIAGRAM GAIN[2:0] = 5 GAIN[2:0] = 4 GAIN[2:0] = 3 GAIN[2:0] = 2 Gain of 32x Gain of 16x Gain of 8x Gain of 4x HIGAIN – PGAx Negative Input PGAxOUT AMPx + PGAx Positive Input PGACAL[7:0] Note 1: x = 1, 2 and 3.  2017-2019 Microchip Technology Inc. DS70005319D-page 409 dsPIC33CH128MP508 FAMILY 4.8.1 MODULE DESCRIPTION negative input source. To provide an independent ground reference, S1PGAxN2 is available as the negative input source to the PGAx module. The Programmable Gain Amplifiers are used to amplify small voltages (i.e., voltages across burden/shunt resistors) to improve the Signal-to-Noise Ratio (SNR) of the measured signal. The PGAx output voltage can be read by any of the four dedicated Sample-and-Hold circuits on the ADC module. The output voltage can also be fed to the comparator module for overcurrent/ voltage protection. Figure 4-22 shows a functional block diagram of the PGAx module. Refer to Section 3.9 “High-Speed, 12-Bit Analog-to-Digital Converter (Master ADC)” for more interconnection details. Note 1: Not all PGA positive/negative inputs are available on all devices. Refer to the specific device pinout for available input source pins. The output voltage of the PGAx module can be connected to the DACOUT1 pin by setting the PGAOEN bit in the PGAxCON register. When the PGAOEN bit is enabled, the output voltage of PGA1 is connected to DACOUT1. There is only one DACOUT1 pin. The gain of the PGAx module is selectable via the GAIN[2:0] bits in the PGAxCON register. There are four gains, ranging from 4x to 48x (with a 1.5 gain multiplier). The SELPI[2:0] and SELNI[2:0] bits in the PGAxCON register select one of the positive/negative inputs to the PGAx module. For single-ended applications, the SELNI[2:0] bits will select the ground as the FIGURE 4-22: If all three of the DACx output voltages and PGAx output voltages are connected to the DACOUT1 pin, the resulting output voltage would be a combination of signals. There is no assigned priority between the PGAx module and the DACx module. PGAx FUNCTIONAL BLOCK DIAGRAM INSEL[2:0] (DACxCONL) SELPI[2:0] PGAxCON(1) PGAEN S1PGAxP1 PGAxCAL(1) + – GAIN[2:0] DACx S1PGAxP2 PGACAL[7:0] GND ADC + S&H PGAx(1) GND – S1PGAxN2 GND SELNI[2:0] PGAOEN To DACOUT1 Pin(2) Note 1: x = 1, 2 and 3. DS70005319D-page 410  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 4.8.2 PGA RESOURCES Many useful resources are provided on the main product page of the Microchip website for the devices listed in this data sheet. This product page contains the latest updates and additional information.  2017-2019 Microchip Technology Inc. 4.8.2.1 Key Resources • “Programmable Gain Amplifier (PGA)” (www.microchip.com/DS70005146) in the “dsPIC33/PIC24 Family Reference Manual” • Code Samples • Application Notes • Software Libraries • Webinars • All Related “dsPIC33/PIC24 Family Reference Manual” Sections • Development Tools DS70005319D-page 411 dsPIC33CH128MP508 FAMILY 4.8.3 PGA CONTROL REGISTERS REGISTER 4-115: PGAxCON: PGAx CONTROL REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PGAEN PGAOEN SELPI2 SELPI1 SELPI0 SELNI2 SELNI1 SELNI0 bit 15 bit 8 U-0 U-0 U-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 — — — HIGAIN — GAIN2 GAIN1 GAIN0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 PGAEN: PGAx Enable bit 1 = PGAx module is enabled 0 = PGAx module is disabled (reduces power consumption) bit 14 PGAOEN: PGAx Output Enable bit 1 = PGAx output is connected to the DACOUT1 pin 0 = PGAx output is not connected to the DACOUT1 pin bit 13-11 SELPI[2:0]: PGAx Positive Input Selection bits 111 = Reserved 110 = Reserved 101 = Reserved 100 = Reserved 011 = Ground 010 = Ground 001 = S1PGAxP2 000 = S1PGAxP1 bit 10-8 SELNI[2:0]: PGAx Negative Input Selection bits 111 = Reserved 110 = Reserved 101 = Reserved 100 = Reserved 011 = Ground (Single-Ended mode) 010 = Reserved 001 = S1PGAxN2 000 = Ground (Single-Ended mode) bit 7-5 Unimplemented: Read as ‘0’ bit 4 HIGAIN: High-Gain Select bit This bit, when asserted, enables a 50% increase in gain as specified by the GAIN[2:0] bits. bit 3 Unimplemented: Read as ‘0’ bit 2-0 GAIN[2:0]: PGAx Gain Selection bits 111 = Reserved 110 = Reserved 101 = Gain of 32x 100 = Gain of 16x 011 = Gain of 8x 010 = Gain of 4x 001 = Reserved 000 = Reserved DS70005319D-page 412  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 4-116: PGAxCAL: PGAx CALIBRATION REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PGACAL[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7-0 PGACAL[7:0]: PGAx Offset Calibration bits The calibration values for PGA1, PGA2 and PGA3 must be copied from Flash addresses, 0xF8001C, 0xF8001CE and 0xF800120, respectively, into these bits before the module is enabled. Refer to the calibration data address table (Table 21-4) in Section 21.0 “Special Features” for more information.  2017-2019 Microchip Technology Inc. DS70005319D-page 413 dsPIC33CH128MP508 FAMILY NOTES: DS70005319D-page 414  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 5.0 MASTER SLAVE INTERFACE (MSI) Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “Master Slave Interface (MSI) Module” (www.microchip.com/ DS70005278) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). The Master Slave Interface (MSI) module is a bridge between the Master and a Slave processor system, each of which operates within independent clock domains. The Master and Slave have their own registers to communicate between the MSI modules; the Master MSI registers are located in the Master SFR space and the Slave MSI registers are in the Slave SFR space. The Master Slave Interface (MSI) includes these characteristics: • 16 Unidirectional Data Mailbox Registers: - Direction of each Mailbox register is fuse-selectable - Byte and word-addressable • Eight Mailbox Data Flow Control Protocol Blocks: - Individual fuse enables - Write port active; read port passive (i.e., no read data request required) - Automatic, interrupt driven (or polled), data flow control mechanism across MSI clock boundary - Fuse assignable to any of the Mailbox registers, supports any length data buffers (up to the number of available Mailbox registers) - DMA transfer compatible • Master to Slave and Slave to Master Interrupt Request with Acknowledge Data Flow Control • Two-Channel FIFO Memory Structure: - One read and one write channel, each 32 words deep - Circular operation with empty and full status, and interrupts - Overflow/underflow detection with interrupts to Master core and Slave core - Interrupt-based, software polled or DMA transfer compatible  2017-2019 Microchip Technology Inc. • Master and Slave Processor Cross-Boundary Control and Status: - Readable operating mode status for both processors - Slave enable from Master (subject to satisfying a hardware write interlock sequencer) - Master interrupt when Slave is reset during code execution - Slave interrupt when Master is reset during code execution • Optional (fuse) Decoupling of Master and Slave Resets; POR/BOR/MCLR always Resets Master and Slave; Influence of Remaining Run-Time Resets on the Slave Enable is Fuse-Programmable 5.1 Master MSI Control Registers The following registers are associated with the Master MSI module and are located in the Master SFR space. • • • • • • • • Register 5-1: MSI1CON Register 5-2: MSI1STAT Register 5-3: MSI1KEY Register 5-4: MSI1MBXS Register 5-5: MSI1MBXnD Register 5-6: MSI1FIFOCS Register 5-7: MRSWFDATA Register 5-8: MWSRFDATA DS70005319D-page 415 dsPIC33CH128MP508 FAMILY REGISTER 5-1: MSI1CON: MSI1 MASTER CONTROL REGISTER R/W-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 SLVEN — — — RFITSEL1 RFITSEL0 MTSIRQ STMIACK bit 15 bit 8 R/W-0 r-0 r-0 r-0 r-0 r-0 r-0 r-0 SRSTIE — — — — — — — bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 SLVEN: Slave Enable bit This bit enables the Slave processor subsystem. Writing to the SLVEN bit is subject to satisfying the MSI1KEY unlock sequence. 1 = Slave processor is enabled, Slave Reset is released and execution is permitted 0 = Slave processor is disabled and held in Reset bit 14-12 Unimplemented: Read as ‘0’ bit 11-10 RFITSEL[1:0]: Read FIFO Interrupt Threshold Select bits 11 = Trigger data valid interrupt when FIFO is full after Slave write 10 = Trigger data valid interrupt when FIFO is 75% full after Slave write 01 = Trigger data valid interrupt when FIFO is 50% full after Slave write 00 = Trigger data valid interrupt when 1st FIFO entry is written by Slave bit 9 MTSIRQ: Master to Slave Interrupt Request bit 1 = Master has issued an interrupt request to the Slave 0 = Master has not issued a Slave interrupt request bit 8 STMIACK: Master to Slave Interrupt Acknowledge bit (to Acknowledge the Slave interrupt) 1 = If STMIRQ = 1, Master Acknowledges Slave interrupt request, else protocol error 0 = If STMIRQ = 0, Master has not yet Acknowledged Slave interrupt request, else no Slave to Master interrupt request is pending bit 7 SRSTIE: Slave Reset Event Interrupt Enable bit 1 = Master Slave Reset event interrupt occurs when Slave enters Reset state 0 = Master Slave Reset event interrupt does not occur when Slave enters Reset state bit 6-0 Reserved: Read as ‘0’ DS70005319D-page 416  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 5-2: MSI1STAT: MSI1 MASTER STATUS REGISTER R-0 R/W-0 R-0 R-0 R/W-0 R-0 R-0 R-0 SLVRST SLVWDRST SLVPWR1 SLVPWR0 VERFERR SLVP2ACT STMIRQ MTSIACK bit 15 bit 8 R-0 r-0 r-0 r-0 r-0 r-0 r-0 r-0 SLVDBG — — — — — — — bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 SLVRST: Slave Reset Status bit Indicates when the Slave is in Reset as the result of any Reset source. Generates a Slave Reset event interrupt to the Master on leading edge of being set when MTSIRQ (MSI1CON[9]) = 1. 1 = Slave is in Reset 0 = Slave is not in Reset bit 14 SLVWDRST: Slave Watchdog Timer (WDT) Reset Status bit Indicates when the Slave has been reset as the result of a WDT time-out. The SLVRST bit will also get set (at the same time this bit is set) by the hardware. 1 = Slave has been reset by the WDT 0 = Slave has not been reset by the WDT bit 13-12 SLVPWR[1:0]: Slave Low-Power Operating Mode Status bits 11 = Reserved 10 = Slave is in Sleep mode 01 = Slave is in Idle mode 00 = Slave is not in a Low-Power mode bit 11 VERFERR: PRAM Verify Error Status bit 1 = Error detected during execution of VFSLV (PRAM write verify) instruction 0 = No error detected during execution of VFSLV (PRAM write verify) instruction bit 10 SLVP2ACT: Slave PRAM Panel 2 Active Status bit This bit is a reflection of the Slave NVM controller, P2ACTIV (NVMCON[10]) status bit, which is toggled after successful execution of a BOOTSWP instruction (during a Slave PRAM LiveUpdate operation). 1 = Slave NVM controller, P2ACTIV (NVMCON[10]) = 1 0 = Slave NVM controller P2ACTIV (NVMCON[10]) = 0 bit 9 STMIRQ: Slave to Master Interrupt Request Status bit 1 = Slave has issued an interrupt request to the Master 0 = Slave has not issued a Master interrupt request bit 8 MTSIACK: Acknowledge Status bit (Slave acknowledged) 1 = If MTSIRQ = 1, Slave Acknowledges Master interrupt request, else protocol error 0 = If MTSIRQ = 1, Slave has not yet Acknowledged Master interrupt request, else no Master to Slave interrupt request is pending bit 7 SLVDBG: Slave Debug Mode Status bit 1 = Slave is operating in Debug mode 0 = Slave is operating in Mission or Application mode bit 6-0 Reserved: Read as ‘0’  2017-2019 Microchip Technology Inc. DS70005319D-page 417 dsPIC33CH128MP508 FAMILY \ REGISTER 5-3: MSI1KEY: MSI1 MASTER INTERLOCK KEY REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 MSI1KEY[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-8 Unimplemented: Read as ‘0’ bit 7-0 MSI1KEY[7:0]: MSI1 Key bits The MSI1KEYx bits are monitored for specific write values. REGISTER 5-4: x = Bit is unknown MSI1MBXS: MSI1 MASTER MAILBOX DATA TRANSFER STATUS REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DTRDY[H:A] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7-0 DTRDY[H:A]: Data Ready Status bits 1 = Data transmitter has indicated that data are available to be read by data receiver in MSI1MBXnD (DTRDYx is automatically set by a data transmitter processor write to assigned MSI1MBXnD); Meaning when configured as a: - Transmitter: Data are written. Waiting for receiver to read. - Receiver: New data are ready to read. 0 = No data are available to be read by receiver in MSI1MBXnD (or the handshake protocol logic block is disabled) DS70005319D-page 418  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY \ REGISTER 5-5: R/W-0 MSI1MBXnD: MSI1 MASTER MAILBOX n DATA REGISTER (n = 0 to 15) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 MSIMBXnD[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 MSIMBXnD[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown MSIMBXnD[15:0]: MSI1 Mailbox n Data bits When Configuration bit, MBXMx = 1 (programmed): Mailbox Data Direction: Master read, Slave write; Master MSIMBXnD[15:0] bits become R-0 (a Master write to MSIMBXnD[15:0] will have no effect). When Configuration bit, MBXMx = 0 (programmed): Mailbox Data Direction: Master write, Slave read; Master MSIMBXnD[15:0] bits become R/W-0.  2017-2019 Microchip Technology Inc. DS70005319D-page 419 dsPIC33CH128MP508 FAMILY \ REGISTER 5-6: MSI1FIFOCS: MSI1 MASTER FIFO CONTROL/STATUS REGISTER R/W-0 U-0 U-0 U-0 R/C-0 R-0 R-0 R-1 WFEN — — — WFOF(1) WFUF(1) WFFULL(1) WFEMPTY(2) bit 15 bit 8 R/W-0 U-0 U-0 U-0 R-0 R/C-0 R-0 R-1 RFEN — — — RFOF RFUF RFFULL RFEMPTY bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 WFEN: Write FIFO Enable bit 1 = Enables (Master) Write FIFO 0 = Disables and initializes (Master) Write FIFO bit 14-12 Unimplemented: Read as ‘0’ bit 11 WFOF: Write FIFO Overflow bit(1) 1 = Write FIFO overflow is detected 0 = No Write FIFO overflow is detected bit 10 WFUF: Write FIFO Underflow bit(1) 1 = Write FIFO underflow is detected 0 = No Write FIFO underflow is detected bit 9 WFFULL: Write FIFO Full Status bit(1) 1 = Write FIFO is full, last write by Master to Write FIFO (WFDATA) was into the last free location 0 = Write FIFO is not full bit 8 WFEMPTY: Write FIFO Empty Status bit(2) 1 = Write FIFO is empty; last read by Slave from Write FIFO (WFDATA) emptied the FIFO of all valid data or FIFO is disabled (and initialized to the empty state) 0 = Write FIFO contains valid data not yet read by the Slave bit 7 RFEN: Read FIFO Enable bit 1 = Enables (Master) the Read FIFO 0 = Disables and initializes the (Master) Read FIFO bit 6-4 Unimplemented: Read as ‘0’ bit 3 RFOF: Read FIFO Overflow bit 1 = Read FIFO overflow is detected 0 = No Read FIFO overflow is detected bit 2 RFUF: Read FIFO Underflow bit 1 = Read FIFO underflow is detected 0 = No Read FIFO underflow is detected bit 1 RFFULL: Read FIFO Full Status bit 1 = Read FIFO is full; last write by Slave to Read FIFO (RFDATA) was into the last free location 0 = Read FIFO is not full bit 0 RFEMPTY: Read FIFO Empty Status bit 1 = Read FIFO is empty; last read by Master from Read FIFO (RFDATA) emptied the FIFO of all valid data or FIFO is disabled (and initialized to the empty state) 0 = Read FIFO contains valid data not yet read by the Master Note 1: 2: Once set, these bits can be cleared by making WFEN = 0. Clearing WFEN will also cause the WFEMPTY status bit to be set. After WFEN is subsequently set, WFEMPTY will remain set until the Master writes data into the Write FIFO. DS70005319D-page 420  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY \ REGISTER 5-7: R-0 MRSWFDATA: MASTER READ (SLAVE WRITE) FIFO DATA REGISTER R-0 R-0 R-0 R-0 R-0 R-0 R-0 MRSWFDATA[15:8] bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 MRSWFDATA[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown MRSWFDATA[15:0]: Read FIFO Data Out Register bits REGISTER 5-8: R-0 MWSRFDATA: MASTER WRITE (SLAVE READ) FIFO DATA REGISTER R-0 R-0 R-0 R-0 R-0 R-0 R-0 MWSRFDATA[15:8] bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 MWSRFDATA[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown MWSRFDATA[15:0]: Write FIFO Data Out Register bits  2017-2019 Microchip Technology Inc. DS70005319D-page 421 dsPIC33CH128MP508 FAMILY 5.2 Slave MSI Control Registers The following registers are associated with the Slave MSI module and are located in the Slave SFR space. • • • • • • • Register 5-9: SI1CON Register 5-10: SI1STAT Register 5-11: SI1MBX Register 5-12: SI1MBXnD Register 5-13: SI1FIFOCS Register 5-14: SWMRFDATA Register 5-15: SRMWFDATA REGISTER 5-9: SI1CON: MSI1 SLAVE CONTROL REGISTER U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — — RFITSEL1 RFITSEL0 STMIRQ MTSIACK bit 15 bit 8 R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 MRSTIE — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-12 Unimplemented: Read as ‘0’ bit 11-10 RFITSEL[1:0]: Read FIFO Interrupt Threshold Select bits 11 = Triggers data valid interrupt when FIFO is full after Slave write 10 = Triggers data valid interrupt when FIFO is 75% full after Slave write 01 = Triggers data valid interrupt when FIFO is 50% full after Slave write 00 = Triggers data valid interrupt when 1st FIFO entry is written by Slave bit 9 STMIRQ: Slave to Master Interrupt Request bit 1 = Interrupts the Master 0 = Does not interrupt the Master bit 8 MTSIACK: Slave to Acknowledge Master Interrupt bit 1 = If MTSIRQ = 1, Slave Acknowledges Master interrupt request, else protocol error 0 = If MTSIRQ = 0, Slave has not yet Acknowledged Master interrupt request, else no Master to Slave interrupt request is pending bit 7 MRSTIE: Master Reset Event Interrupt Enable bit 1 = Slave Master Reset event interrupt occurs when Master enters Reset state 0 = Slave Master Reset event interrupt does not occur when Master enters Reset state bit 6-0 Unimplemented: Read as ‘0’ DS70005319D-page 422  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 5-10: SI1STAT: MSI1 SLAVE STATUS REGISTER R-0 U-0 R-0 R-0 U-0 U-0 R-0 R-0 MSTRST — MSTPWR1 MSTPWR0 — — MTSIRQ STMIACK bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 MSTRST: Master Reset Status bit Indicates when the Master is in Reset as the result of any Reset source. Generates a Master Reset event interrupt to the Slave on the leading edge of being set when STMIRQ (SI1CON[9]) = 1. 1 = Master is in Reset 0 = Master is not in Reset bit 14 Unimplemented: Read as ‘0’ bit 13-12 MSTPWR[1:0]: Master Low-Power Operating Mode Status bits 11 = Reserved 10 = Master is in Sleep mode 01 = Master is in Idle mode 00 = Master is not in a Low-Power mode bit 11-10 Unimplemented: Read as ‘0’ bit 9 MTSIRQ: Master interrupt Slave bit 1 = Master has issued an interrupt request to the Slave 0 = Master has not issued a Slave interrupt request bit 8 STMIACK: Master Acknowledgment Status bit 1 = If STMIRQ = 1, Master Acknowledges Slave interrupt request, else protocol error 0 = If STMIRQ = 0, Master has not yet Acknowledged Slave interrupt request, else no Slave to Master interrupt request is pending bit 7-0 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. DS70005319D-page 423 dsPIC33CH128MP508 FAMILY REGISTER 5-11: SI1MBX: MSI1 SLAVE MAILBOX DATA TRANSFER STATUS REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 DTRDY[H:A] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7-0 DTRDY[H:A]: Data Ready Status bits 1 = Data transmitter has indicated that data are available to be read by data receiver in MSI1MBXnD (DTRDYx is automatically set by a data transmitter processor write to assigned MSI1MBXnD) Meaning when configured as a: - Transmitter: Data are written. Waiting for receiver to read. - Receiver: New data are ready to read. 0 = No data are available to be read in receiver, MSI1MBXnD (or the handshake protocol logic block is disabled) REGISTER 5-12: R/W-0 SI1MBXnD: MSI1 SLAVE MAILBOX n DATA REGISTER (n = 0 TO 15) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SIMBXnD[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SIMBXnD[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown SIMBXnD[15:0]: MSI1 Slave Mailbox Data n bits When Configuration bit, MBXMx = 1 (programmed): Mailbox Data Direction: Master read, Slave writes Master; SIMBXnD[15:0] bits become R-0 (a Master write to SIMBXnD[15:0] will have no effect). When Configuration bit, MBXMx = 0 (programmed): Mailbox Data Direction: Master write, Slave reads Master; SIMBXnD[15:0] bits become R/W-0. DS70005319D-page 424  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 5-13: SI1FIFOCS: MSI1 SLAVE FIFO STATUS REGISTER R-0 U-0 U-0 U-0 R-0 R/C-0 R-0 R-1 SRFEN — — — SRFOF SRFUF SRFFULL SRFEMPTY bit 15 bit 8 R-0 U-0 U-0 U-0 R/C-0 R-0 R-0 R-1 SWFEN — — — SWFOF SWFUF SWFFULL SWFEMPTY bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 SRFEN: Slave Read (Master Write) FIFO Enable bit 1 = Enables Slave Read (Master Write) FIFO 0 = Disables Slave Read (Master Write) FIFO bit 14-12 Unimplemented: Read as ‘0’ bit 11 SRFOF: Slave Read (Master Write) FIFO Overflow bit 1 = Slave Read FIFO overflow is detected 0 = No Slave Read FIFO overflow is detected bit 10 SRFUF: Slave Read (Master Write) FIFO Underflow bit 1 = Slave Read (Master Write) FIFO underflow is detected 0 = No Slave Read (Master Write) FIFO underflow is detected bit 9 SRFFULL: Slave Read (Master Write) FIFO Full Status bit 1 = Slave Read (Master Write) FIFO is full; last write by Master to Slave Read FIFO (SRMWFDATA) was into the last free location 0 = Slave Read (Master Write) FIFO is not full bit 8 SRFEMPTY: Slave Read (Master Write) FIFO Empty Status bit 1 = Slave Read (Master Write) FIFO is empty; last read by Slave from Read FIFO (SRMWFDATA) emptied the FIFO of all valid data or FIFO is disabled (and initialized to the empty state) 0 = Slave Read (Master Write) FIFO contains valid data not yet read by the Slave bit 7 SWFEN: Slave Write (Master Read) FIFO Enable bit 1 = Enables Slave Write (Master Read) FIFO 0 = Disables Slave Write (Master Read) FIFO bit 6-4 Unimplemented: Read as ‘0’ bit 3 SWFOF: Slave Write (Master Read) FIFO Overflow bit 1 = Slave Write (Master Read) FIFO overflow is detected 0 = No Slave Write (Master Read) FIFO overflow is detected bit 2 SWFUF: Slave Write (Master Read) FIFO Underflow bit 1 = Slave Write (Master Read) FIFO underflow is detected 0 = No Slave Write (Master Read) FIFO underflow is detected bit 1 SWFFULL: Slave Write (Master Read) FIFO Full Status bit 1 = Slave Write (Master Read) FIFO is full; last write by Slave to FIFO (SWMRFDATA) was into the last free location 0 = Slave Write (Master Read) FIFO is not full bit 0 SWFEMPTY: Slave Write (Master Read) FIFO Empty Status bit 1 = Slave Write (Master Read) FIFO is empty; last read by Master from Read FIFO emptied the FIFO of all valid data or FIFO is disabled (and initialized to the empty state) 0 = Slave Write (Master Read) FIFO contains valid data not yet read by the Master  2017-2019 Microchip Technology Inc. DS70005319D-page 425 dsPIC33CH128MP508 FAMILY REGISTER 5-14: W-0 SWMRFDATA: SLAVE WRITE (MASTER READ) FIFO DATA REGISTER W-0 W-0 W-0 W-0 W-0 W-0 W-0 SWMRFDATA[15:8] bit 15 bit 8 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 SWMRFDATA[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown SWMRFDATA[15:0]: Read FIFO Data Out Register bits REGISTER 5-15: R-0 SRMWFDATA: SLAVE READ (MASTER WRITE) FIFO DATA REGISTER R-0 R-0 R-0 R-0 R-0 R-0 R-0 SRMWFDATA[15:8] bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 SRMWFDATA[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown SRMWFDATA[15:0]: Write FIFO Data Out Register bits DS70005319D-page 426  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 5.3 Slave Processor Control The MSI contains three control bits related to Slave processor control within the MSI1CON register. 5.3.1 SLAVE ENABLE (SLVEN) CONTROL The SLVEN (MSI1CON[15]) control bit provides a means for the Master processor to enable or disable the Slave processor. When the SLVEN bit lock is enabled (i.e., the bits are locked and cannot be modified), the instruction sequence shown in Example 5-1 must be executed to open the lock. The unlock sequence is a prerequisite to both setting and clearing the target control bit. Note: The Slave is disabled when SLVEN (MSI1CON[15]) = 0. In this state: • The Slave is held in the Reset state • The Master has access to the Slave PRAM (to load it out of a device Reset) • The Slave Reset status bit, SLVRST (MSI1STAT[15]) = 1 The Slave is enabled when SLVEN (MSI1CON[15]) = 1. In this state: • The Slave Reset is released and it will start to execute code in whatever mode it is configured to operate in • The Master processor will no longer have access to the Slave PRAM • The Slave Reset status bit, SLVRST (MSI1STAT[15]) = 0 Note: The SLVRST (MSI1STAT[15]) status bit indicates when the Slave is in Reset. The associated interrupt only occurs when the Slave enters the Reset state after having previously not been in Reset. That is, no interrupt can be generated until the Slave is first enabled. The SLVEN bit may only be modified after satisfying the hardware write interlock. The SLVEN bit is protected from unexpected writes through a software unlocking sequence that is based on the MSI1KEY register. Given the critical nature of the MSI control interface, the MSI macro unlock mechanism is independent from that of the Flash controller for added robustness. Completing a predefined data write sequence to the MSI1KEY register will open a window. The SLVEN bit should be written on the first instruction that follows the unlock sequence. No other bits within the MSI1CON register are affected by the interlock. The MSI1KEY register is not a physical register. A read of the MSI1KEY register will read all ‘0’s.  2017-2019 Microchip Technology Inc. It is recommended to enable SRSTIE (MSI1CON[7]) = 1 prior to enabling the SLVEN bit. This will make the design robust and will update the Master with the Reset state of the Slave. EXAMPLE 5-1: MSI ENABLE OPERATION //Unlock Key to allow MSI Enable control MOV.b #0x55, W0 MOV.b WREG, MSI1KEY MOV.b #0xAA, W0 MOV.b WREG, MSI1KEY // Enable MSI BSET MSI1CON, SLVEN EXAMPLE 5-2: MSI ENABLE OPERATION IN C CODE #include _start_slave(); 5.4 Slave Reset Coupling Control In all operating modes, the user may couple or decouple the Master Run-Time Resets to the Slave Reset by using the Master Slave Reset Enable (S1MSRE) fuse. The Resets are effectively coupled by directing the selected Reset source to the SLVEN bit Reset. In all operating modes, the user may also choose whether the SLVEN bit is reset or not in the event of a Slave Run-Time Reset by using the Slave Reset Enable (S1SSRE) fuse. A user may choose to reset SLVEN in the event of a Slave Reset because that event could be an indicator of a problem with Slave execution. The Slave would be placed in Reset and the Master alerted (via the Slave Reset event interrupt, need to make SRSTIE (MSI1CON[7] = 1) to attempt to rectify the problem. The Master must re-enable the Slave by setting the SLVEN bit again. Alternatively, the user may choose to not halt the Slave in the event of a Slave Reset, and just allow it to restart execution after a Reset and continue operation as soon as possible. The Slave Reset event interrupt would still occur, but could be ignored by the Master. DS70005319D-page 427 dsPIC33CH128MP508 FAMILY TABLE 5-1: APPLICATION MODE SLVEN RESET CONTROL TRUTH TABLE S1MSRE S1SSRE SLVEN Bit Reset Source Application Effect 0 0 Master Resets(1) • Slave is reset and disabled in the event of a POR, BOR or MCLR Reset. Master must re-enable Slave. • Slave Run-Time Resets will not disable Slave. Slave will reset and continue execution (and may optionally interrupt Master). 1 0 Master Resets(1) • Slave is reset and disabled in the event of a POR, BOR or MCLR Reset. Master must re-enable Slave. • Slave Run-Time Resets will not disable Slave. Slave will reset and continue execution (and may optionally interrupt Master). 0 1 1 1 Note 1: 2: 5.4.1 Master Resets(1) and • Slave is reset and disabled in the event of any Slave Run-Time Slave Resets(2) Reset (and may optionally interrupt Master). Master must re-enable Slave to execute the Slave code. • Master Run-Time Resets will not affect Slave operation. POR/BOR/MCLR(1) Slave Resets(2) • Slave is reset and disabled in the event of any Slave Run-Time Reset or Master Reset. Master must re-enable Slave. This represents the default state (S1MSRE and S1SSRE are unprogrammed). Master Resets include any Master Reset, such as POR/BOR/MCLR Resets. Slave Resets include any Slave Reset, plus POR/BOR/MCLR Resets (in Application mode). INTER-PROCESSOR INTERRUPT REQUEST AND ACKNOWLEDGE The Master and Slave processors may interrupt each other directly. The Master may issue an interrupt request to the Slave by asserting the MTSIRQ (MSI1CON[9]) control bit. Similarly, the Slave may issue an interrupt request to the Master by asserting the STMIRQ (MSI1STAT[9]) control bit. The interrupts are Acknowledged through the use of the Interrupt Acknowledge bits, MTSIACK (MSI1STAT[8]) for the Master to Slave interrupt request and STMIACK (MSI1CON[8]) for the Slave to Master interrupt request. DS70005319D-page 428 5.4.2 READ ADDRESS POINTERS FOR FIFOs The MSI macro may also include a set of two FIFOs, one for data reads from the Slave and the other for data writes to the Slave. The Read Address Pointers for the Read and Write FIFOs are held in the RDPTR[6:0] bits (MSI1CON[6:0]) and WRPTR[6:0] bits (MSI1STAT[6:0]), respectively. These bits are accessible only from within Debug mode.  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 6.0 OSCILLATOR WITH HIGH-FREQUENCY PLL • Master and Slave Independent On-Chip Phase-Locked Loop (PLL) to Boost Internal Operating Frequency on Select Internal and External Oscillator Sources • Master and Slave Independent Auxiliary PLL (APLL) Clock Generator to Boost Operating Frequency for Peripherals • Master and Slave Independent Doze mode for System Power Savings • Master and Slave Independent Scalable Reference Clock Output (REFCLKO) • On-the-Fly Clock Switching between Various Clock Sources • Fail-Safe Clock Monitoring (FSCM) that Detects Clock Failure and Permits Safe Application Recovery or Shutdown Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “Oscillator Module with High-Speed PLL” (www.microchip.com/DS70005255) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). The dsPIC33CH128MP508 family oscillator with high-frequency PLL includes these characteristics: • Master and Core Subsystems • Internal and External Oscillator Sources Shared between Master and Slave Cores FIGURE 6-1: A block diagram of the dsPIC33CH128MP508 oscillator system is shown in Figure 6-1. MASTER AND SLAVE CORE SHARED CLOCK SOURCES BLOCK DIAGRAM Master FCY BFRC 8 MHz TUN[5:0](1) BFRCCLK FRCCLK Master Core Clock Selection and POSCCLK PLL/DIV LPRCCLK Subsystem FRC 8 MHz Master FP Master FOSC Master VCO Outputs Master APLL and AVCO Outputs Master REFCLKO OSCO POSC(2) OSCI LPRC 32 kHz Slave FCY LPRCCLK Slave Core Clock POSCCLK Selection and FRCCLK BFRCCLK PLL/DIV Subsystem Slave FP Slave FOSC Slave VCO Outputs Slave APLL and AVCO Outputs Slave REFCLKO Note 1: FRC Oscillator tuning bits are configured in the Master core OSCTUN register. 2: POSC is configured through the POSCMD[1:0] bits in the Master FOSC Configuration register.  2017-2019 Microchip Technology Inc. DS70005319D-page 429 dsPIC33CH128MP508 FAMILY FIGURE 6-2: MASTER CORE OSCILLATOR SUBSYSTEM FVCO(3) VCO Divider FVCO FVCO/2(8) FVCO/3 FVCO/4(7) DOZE[2:0] FVCODIV COSC[2:0] FRCCLK(1) DOZE VCODIV[1:0] FPLLO(6,8) FCY S1 PLL(2) (1) POSCCLK ÷2 POSCCLK(1) S3 FPLLO/2 (5) FRCCLK FRCDIVN FRCDIVN FRCCLK(1) BFRCCLK(1) LPRCCLK(1) FP S2 S1/S3 ÷2 S0 FOSC S7 S6 REFOI (PPS) Pin FVCO/4 BFRC LPRC FRC POSC FP FOSC S5 FRCDIV[2:0] Clock Fail Clock Switch RODIV[14:0] ÷N REFCLKO ROSEL[3:0] Reset Auxiliary PLL S6 NOSC[2:0] FNOSC[2:0] POSCCLK FRC AFPLLO(6,8) APLL FRCSEL AFVCO(4) AFVCO AFVCO/2(6,8) AVCO AFVCO/3 Divider AFVCO/4 AFVCODIV(7) AVCODIV[1:0] CAN Clock Generation Note 1: 2: 3: 4: 5: 6: 7: 8: From Master and Slave core shared oscillator source. See Figure 6-4 for details of the PLL module. See Figure 6-4 for the source of FVCO. See Figure 6-4 for the source of AVCO. XTPLL, HSPLL, ECPLL, FRCPLL (FPLLO). Clock option for PWM. Clock option for ADC. Clock option for DAC. DS70005319D-page 430 No Clock FVCO FPLLO FVCO/2 FVCO/3 FVCO/4 AFPLLO AFVCO AFVCO/2 AFVCO/3 AFVCO/4 ÷N FCAN CANDIV[6:0] CANCLKSEL[3:0]  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 6-3: SLAVE CORE OSCILLATOR SUBSYSTEM FVCO(3) FVCO FVCO/2(8) FVCO/3 FVCO/4(7) VCO Divider DOZE[2:0] FVCODIV COSC[2:0] FRCCLK DOZE VCODIV[1:0] FPLLO(6,8) FCY S1 (1) PLL(2) POSCCLK(1) S3 ÷2 POSCCLK(1) FP S2 (5) FPLLO/2 FRCCLK FRCDIV FRCDIVN FRCCLK(1) BFRCCLK(1) LPRCCLK(1) S1/S3 ÷2 S0 FOSC S7 S6 FRCDIV[2:0] Clock Fail Clock Switch RODIV[14:0] REFOI (PPS) Pin FVCO/4 BFRC LPRC FRC POSC FP FOSC S5 ÷N REFCLKO Reset ROSEL[3:0] Auxiliary PLL S6 NOSC[2:0] FNOSC[2:0] POSCCLK APLL AFPLLO(6,8) FRC FRCSEL AFVCO(4) AVCO Divider Note 1: 2: 3: 4: 5: 6: 7: 8: From Master and Slave core shared oscillator source. See Figure 6-4 for details of the PLL module. See Figure 6-4 for the source of FVCO. See Figure 6-4 for the source of AVCO. XTPLL, HSPLL, ECPLL, FRCPLL (FPLLO). Clock option for PWM. Clock option for ADC. Clock option for DAC.  2017-2019 Microchip Technology Inc. AFVCO AFVCO/2(6,8) AFVCO/3 AFVCO/4 AFVCODIV(7) AVCODIV[1:0] DS70005319D-page 431 dsPIC33CH128MP508 FAMILY 6.1 Primary PLL For PLL operation, the following requirements must be met at all times without exception: The Primary Oscillator and internal FRC Oscillator sources can optionally use an on-chip PLL to obtain higher operating speeds. There are two independent instantiations of PLL for the Master and Slave clock subsystems. Figure 6-4 illustrates a block diagram of the Master/Slave core PLL module. FIGURE 6-4: • The PLL Input Frequency (FPLLI) must be in the range of 8 MHz to 64 MHz • The PFD Input Frequency (FPFD) must be in the range of 8 MHz to (FVCO/16) MHz The VCO Output Frequency (FVCO) must be in the range of 400 MHz to 1600 MHz MASTER/SLAVE CORE PLL AND VCO DETAIL COSC[2:0] FRCCLK(1) POSCCLK(1) S1 S3 DIV 1-8 POST1DIV[2:0] PLL Ready (LOCK) PLLPRE[3:0] Lock Detect PFD VCO POST2DIV[2:0] DIV 1-7 DIV 1-7 Feedback Divider 16-200 PLLFBDIV[7:0] FPLLO(2,4) FVCO VCO Divider FVCO FVCO/2(4) FVCO/3 FVCO/4(3) FVCODIV VCODIV[1:0] Note 1: 2: 3: 4: From Master and Slave core shared oscillator source. Clock option for PWM. Clock option for ADC. Clock option for DAC. DS70005319D-page 432  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY Equation 6-1 provides the relationship between the PLL Input Frequency (FPLLI) and VCO Output Frequency (FVCO). EQUATION 6-1: MASTER/SLAVE CORE FVCO CALCULATION FVCO = FPLLI   M  = FPLLI   PLLFBDIV[7:0]   PLLPRE[3:0]   N1 Equation 6-2 provides the relationship between the PLL Input Frequency (FPLLI) and PLL Output Frequency (FPLLO). EQUATION 6-2: MASTER/SLAVE CORE FPLLO CALCULATION PLLFBDIV[7:0] M  = FPLLI    FPLLO = FPLLI   N1 N2N3  PLLPRE[3:0] POST1DIV[2:0]POST2DIV[2:0]  Where: M = PLLFBDIV[7:0] N1 = PLLPRE[3:0] N2 = POST1DIV[2:0] N3 = POST2DIV[2:0] Note: The PLL Phase Detector Input Divider Select (PLLPREx) bits and the PLL Feedback Divider (PLLFBDIVx) bits should not be changed when operating in PLL mode. Therefore, the user must start on either a nonPLL source or clock switch to a non-PLL source (e.g., internal FRC Oscillator) to make any necessary changes and then clock switch to the desired PLL source. Using Two-Speed Start-up (IESO, FOSCSEL[7]) with a PLL source will start the device on the FRC while preparing the PLL. Once the PLL is ready, the device will switch automatically to the new source. This mode should not be used if changes are needed to the PLLPREx and PLLFBDIVx bits because the PLL may be running before user code execution begins. Also, it is not permitted to directly clock switch from one PLL clock source to a different PLL clock source. The user would need to transition between PLL clock sources with a clock switch to a non-PLL clock source.  2017-2019 Microchip Technology Inc. DS70005319D-page 433 dsPIC33CH128MP508 FAMILY EXAMPLE 6-1: CODE EXAMPLE FOR USING MASTER PRIMARY PLL WITH 8 MHz INTERNAL FRC //code example for 50 MIPS system clock using 8MHz FRC // Select FRC on POR #pragma config FNOSC = FRC // Oscillator Source Selection (Internal Fast RC (FRC)) #pragma config IESO = OFF // Enable Clock Switching #pragma config FCKSM = CSECMD int main() { // Configure PLL prescaler, both PLL postscalers, and PLL feedback divider CLKDIVbits.PLLPRE = 1; // N1=1 PLLFBDbits.PLLFBDIV = 125; // M = 125 PLLDIVbits.POST1DIV = 5; // N2=5 PLLDIVbits.POST2DIV = 1; // N3=1 // Initiate Clock Switch to FRC with PLL (NOSC=0b001) __builtin_write_OSCCONH(0x01); __builtin_write_OSCCONL(OSCCON | 0x01); // Wait for Clock switch to occur while (OSCCONbits.OSWEN!= 0); } Note: FPLLO = FPLLI * M/(N1 * N2 * N3); FPLLI = 8; M = 125; N1 = 1; N2 = 5; N3 = 1; so FPLLO = 8 * 125/(1 * 5 * 1) = 200 MHz or 50 MIPS. EXAMPLE 6-2: CODE EXAMPLE FOR USING SLAVE PRIMARY PLL WITH 8 MHz INTERNAL FRC //code example for 60 MIPS system clock using 8MHz FRC // Select Internal FRC at POR // Select FRC on POR #pragma config S1FNOSC = FRC // Oscillator Source Selection (Internal Fast RC (FRC)) #pragma config S1IESO = OFF // Two-speed Oscillator Start-up Enable bit (Start up with user-selected oscillator source) // Enable Clock Switching #pragma config S1FCKSM = CSECMD int main() { // Configure PLL prescaler, both PLL postscalers, and PLL feedback divider CLKDIVbits.PLLPRE = 1; // N1=1 PLLFBDbits.PLLFBDIV = 150; // M = 150 PLLDIVbits.POST1DIV = 5; // N2=5 PLLDIVbits.POST2DIV = 1; // N3=1 // Initiate Clock Switch to FRC with PLL (NOSC=0b001) __builtin_write_OSCCONH(0x01); __builtin_write_OSCCONL(OSCCON | 0x01); // Wait for Clock switch to occur while (OSCCONbits.OSWEN!= 0); } Note: FPLLO = FPLLI * M/(N1 * N2 * N3); FPLLI = 8; M = 150; N1 = 1; N2 = 5; N3 = 1; so FPLLO = 8 * 150/(1 * 5 * 1) = 240 MHz or 60 MIPS. DS70005319D-page 434  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 6.2 Auxiliary PLL For APLL operation, the following requirements must be met at all times without exception: The dsPIC33CH128MP508 device family implements an Auxiliary PLL (APLL) module for each core present. There are two independent instantiations of APLL for the Master and Slave clock subsystems. The APLL is used to generate various peripheral clock sources independent of the system clock. Figure 6-5 shows a block diagram of the Master/Slave core APLL module. FIGURE 6-5: • The APLL Input Frequency (AFPLLI) must be in the range of 8 MHz to 64 MHz • The APFD Input Frequency (AFPFD) must be in the range of 8 MHz to (AFVCO/16) MHz • The AVCO Output Frequency (AFVCO) must be in the range of 400 MHz to 1600 MHz MASTER/SLAVE CORE APLL AND VCO DETAIL APLL Ready (APLLCLK) APLLPRE[3:0] FRCCLK(1) (1) POSCCLK DIV 1-8 APFD APLLEN APOST1DIV[2:0] APOST2DIV[2:0] 0 Lock Detect AVCO DIV 1-7 DIV 1-7 1 AFPLLO(2,4) FRCSEL Feedback Divider 16-200 APLLFBDIV[7:0] AFVCO AVCO Divider AFVCO AFVCO/2(2,4) AFVCO/3 AFVCO/4 AFVCODIV(3) AVCODIV[1:0] Note 1: 2: 3: 4: From Master and Slave core shared oscillator source. Clock option for PWM. Clock option for ADC. Clock option for DAC.  2017-2019 Microchip Technology Inc. DS70005319D-page 435 dsPIC33CH128MP508 FAMILY Equation 6-3 provides the relationship between the APLL Input Frequency (AFPLLI) and the AVCO Output Frequency (AFVCO). EQUATION 6-3: MASTER/SLAVE CORE AFVCO CALCULATION AFVCO = AFPLLI   M  = AFPLLI   APLLFBDIV[7:0]   APLLPRE[3:0]   N1 Equation 6-4 provides the relationship between the APLL Input Frequency (AFPLLI) and APLL Output Frequency (AFPLLO). EQUATION 6-4: MASTER/SLAVE CORE AFPLLO CALCULATION APLLFBDIV[7:0] M  = AFPLLI    AFPLLO = AFPLLI    N1 N2N3   APLLPRE[3:0] POST1DIV[2:0]POST2DIV[2:0]  Where: M = APLLFBDIV[7:0] N1 = APLLPRE[3:0] N2 = APOST1DIV[2:0] N3 = APOST2DIV[2:0] EXAMPLE 6-3: CODE EXAMPLE FOR USING MASTER OR SLAVE AUXILIARY PLL WITH THE INTERNAL FRC OSCILLATOR //code example for AFVCO = 1 GHz and AFPLLO = 500 MHz using 8 MHz internal FRC // Configure the source clock for the APLL ACLKCON1bits.FRCSEL = 1; // Select internal FRC as the clock source // Configure the APLL prescaler, APLL feedback divider, and both APLL postscalers. ACLKCON1bits.APLLPRE = 1; // N1 = 1 APLLFBD1bits.APLLFBDIV = 125; // M = 125 APLLDIV1bits.APOST1DIV = 2; // N2 = 2 APLLDIV1bits.APOST2DIV = 1; // N3 = 1 // Enable APLL ACLKCON1bits.APLLEN = 1; Note: Even with the APLLEN bit set, another peripheral must generate a clock request before the APLL will start. DS70005319D-page 436  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 6.3 CPU Clocking Each core’s system clock source is divided by two to produce the internal instruction cycle clock. In this document, the instruction cycle clock is denoted by FCY. The timing diagram in Figure 6-6 illustrates the relationship between the system clock (FOSC), the instruction cycle clock (FCY) and the Program Counter (PC). While the Master and Slave subsystems share access to a single set of oscillator sources, all other clocking logic is implemented individually. The Master and Slave core can be configured independently to use any of the following clock configurations: • Primary Oscillator (POSC) on the OSCI and OSCO pins • Internal Fast RC Oscillator (FRC) with optional clock divider • Internal Low-Power RC Oscillator (LPRC) • Primary Oscillator with PLL (ECPLL, HSPLL, XTPLL) • Internal Fast RC Oscillator with PLL (FRCPLL) • Backup Internal Fast RC Oscillator (BFRC) FIGURE 6-6: The internal instruction cycle clock (FCY) can be output on the OSCO I/O pin if the Primary Oscillator mode (POSCMD[1:0]) is not configured as HS/XT. Refer to Table 6-3 for the dual core function of the OSCO pin. CLOCK AND INSTRUCTION CYCLE TIMING TCY FOSC FCY PC PC PC + 2 PC + 4 Fetch INST (PC) Execute INST (PC – 2) Fetch INST (PC + 2) Execute INST (PC) Fetch INST (PC + 4) Execute INST (PC + 2)  2017-2019 Microchip Technology Inc. DS70005319D-page 437 dsPIC33CH128MP508 FAMILY 6.4 Primary Oscillator (POSC) 6.6 Low-Power RC (LPRC) Oscillator The dsPIC33CH128MP508 family devices contain one instance of the Primary Oscillator (POSC), which is available to both the Master and Slave clock subsystems. The Primary Oscillator is available on the OSCI and OSCO pins of the dsPIC33CH devices. This connection enables an external crystal (or ceramic resonator) to provide the clock to the device. The Primary Oscillator provides three modes of operation: The dsPIC33CH128MP508 family devices contain one instance of the Low-Power RC (LPRC) Oscillator that is available to both the Master and Slave clock subsystems. The LPRC Oscillator provides a nominal clock frequency of 32 kHz and is the clock source for the Power-up Timer (PWRT), Watchdog Timer (WDT) and Fail-Safe Clock Monitor (FSCM) circuits in each core clock subsystem. • Medium Speed Oscillator (XT Mode): The XT mode is a Medium Gain, Medium Frequency mode used to work with crystal frequencies of 3.5 MHz to 10 MHz. • High-Speed Oscillator (HS Mode): The HS mode is a High-Gain, High-Frequency mode used to work with crystal frequencies of 10 MHz to 32 MHz. • External Clock Source Operation (EC Mode): If the on-chip oscillator is not used, the EC mode allows the internal oscillator to be bypassed. The device clocks are generated from an external source (0 MHz to up to 64 MHz) and input on the OSCI pin. The LPRC Oscillator is the clock source for the PWRT, WDT and FSCM in both the Master and Slave cores. The LPRC Oscillator is enabled at power-on. Note: 6.5 The Primary Oscillator (POSC) is shared between Master and Slave. Internal Fast RC (FRC) Oscillator The dsPIC33CH128MP508 family devices contain one instance of the internal Fast RC (FRC) Oscillator, which is available to both the Master and Slave clock subsystems. The FRC Oscillator provides a nominal 8 MHz clock without requiring an external crystal or ceramic resonator, which results in system cost savings for applications that do not require a precise clock reference. The application software can tune the frequency of the oscillator using the FRC Oscillator Tuning bits (TUN[5:0]) in the FRC Oscillator Tuning register (OSCTUN[5:0]). Note: The LPRC Oscillator remains enabled under these conditions: • The Master or Slave FSCM is enabled • The Master or Slave WDT is enabled • The LPRC Oscillator is selected as the system clock If none of these conditions is true, the LPRC Oscillator shuts off after the PWRT expires. The LPRC Oscillator is shut off in Sleep mode. Note: 6.7 The LPRC is shared between Master and Slave. Backup Internal Fast RC (BFRC) Oscillator The oscillator block provides a stable reference clock source for the Fail-Safe Clock Monitor (FSCM). When FSCM is enabled in the FCKSM[1:0] Configuration bits (FOSC[7:6]), it constantly monitors the main clock source against a reference signal from the 8 MHz Backup Internal Fast RC (BFRC) Oscillator. In case of a clock failure, the Fail-Safe Clock Monitor switches the clock to the BFRC Oscillator, allowing for continued low-speed operation or a safe application shutdown. The FRC is shared between Master and Slave; the OSCTUN register is used to tune the FRC as a part of the Master oscillator configuration. DS70005319D-page 438  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 6.8 Reference Clock Output In addition to the CLKO output (FOSC/2), the dsPIC33CH128MP508 family devices can be configured to provide a reference clock output signal to a port pin. This feature is available in all oscillator configurations and allows the user to select a greater range of clock sub- FIGURE 6-7: multiples to drive external devices in the application. CLKO is enabled by Configuration bit, OSCIOFNC, and is independent of the REFCLKO reference clock. REFCLKO is mappable to any I/O pin that has mapped output capability. The reference clock output module block diagram is shown in Figure 6-7. REFERENCE CLOCK GENERATOR REFOI (PPS) Pin 1000 FVCO/4 0110 BFRC 0101 LPRC 0100 FRC 0011 POSC 0010 Peripheral Clock (FP) 0001 System Clock (FOSC) 0000 ROTRIM[8:0] ROOUT REFCLKO (PPS) Divider RODIV[14:0] To SPI, CCP, CLC ROSEL[3:0] This reference clock output is controlled by the REFOCONL and REFOCONH registers. Setting the ROEN bit (REFOCONL[15]) makes the clock signal available on the REFCLKO pin. The RODIV[14:0] bits (REFOCONH[14:0]) and ROTRIM[8:0] bits (REFOTRIM[15:7]) enable the selection of different clock divider options. The formula for determining the final frequency output is shown in Equation 6-5. The ROSWEN bit (REFOCONL[9]) indicates that the clock divider has been successfully switched. In order to switch the REFCLKO divider, the user should ensure that this bit reads as ‘0’. Write the updated values to the RODIV[14:0] or ROTRIM[8:0] bits, set the ROSWEN bit and then wait until it is cleared before assuming that the REFCLKO clock is valid. EQUATION 6-5: FREFOUT = CALCULATING FREQUENCY OUTPUT FREFIN 2 • (RODIV[14:0] + ROTRIM[8:0]/512) The ROSEL[3:0] bits (REFOCONL[3:0]) determine which clock source is used for the reference clock output. The ROSLP bit (REFOCONL[11]) determines if the reference source is available on REFCLKO when the device is in Sleep mode. To use the reference clock output in Sleep mode, both the ROSLP bit must be set and the clock selected by the ROSEL[3:0] bits must be enabled for operation during Sleep mode, if possible. Clearing the ROSEL[3:0] bits allows the reference output frequency to change, as the system clock changes during any clock switches. The ROOUT bit enables/disables the reference clock output on the REFCLKO pin. The ROACTIV bit (REFOCONL[8]) indicates that the module is active; it can be cleared by disabling the module (setting ROEN to ‘0’). The user must not change the reference clock source, or adjust the divider when the ROACTIV bit indicates that the module is active. To avoid glitches, the user should not disable the module until the ROACTIV bit is ‘1’. Where: FREFOUT = Output Frequency FREFIN = Input Frequency When RODIV[14:0] = 0, the output clock is the same as the input clock.  2017-2019 Microchip Technology Inc. DS70005319D-page 439 dsPIC33CH128MP508 FAMILY 6.9 OSCCON Unlock Sequence The OSCCON register is protected against unintended writes through a lock mechanism. The upper and lower bytes of OSCCON have their own unlock sequence, and both must be used when writing to both bytes of the register. Before OSCCON can be written to, the following unlock sequence must be used: 1. 2. Execute the unlock sequence for the OSCCON high byte. In two back-to-back instructions: • Write 0x78 to OSCCON[15:8] • Write 0x9A to OSCCON[15:8] In the instruction immediately following the unlock sequence, the OSCCON[15:8] bits can be modified. DS70005319D-page 440 3. 4. Execute the unlock sequence for the OSCCON low byte. In two back-to-back instructions: • Write 0x46 to OSCCON[7:0] • Write 0x57 to OSCCON[7:0] In the instruction immediately following the unlock sequence, the OSCCON[7:0] bits can be modified. Note: MPLAB® XC16 provides a built-in C language function, including the unlocking sequence to modify high and low bytes in the OSCCON register: __builtin_write_OSCCONH(value) __builtin_write_OSCCONL(value)  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY Example 6-4 illustrates code for using the PLL (50 MIPS) with the Primary Oscillator. EXAMPLE 6-4: CODE EXAMPLE FOR USING MASTER PLL (50 MIPS) WITH PRIMARY OSCILLATOR (POSC) //code example for 50 MIPS system clock using POSC with 10 MHz external crystal // Select Internal FRC at POR // Select FRC on POR #pragma config FNOSC = FRC // Oscillator Source Selection (Internal Fast RC (FRC)) #pragma config IESO = OFF /// Enable Clock Switching and Configure POSC in XT mode #pragma config POSCMD = XT #pragma config FCKSM = CSECMD int { main() // Configure PLL prescaler, both PLL postscalers, and PLL feedback divider CLKDIVbits.PLLPRE = 1; // N1=1 PLLFBDbits.PLLFBDIV = 100; // M = 100 PLLDIVbits.POST1DIV = 5; // N2=5 PLLDIVbits.POST2DIV = 1; // N3=1 // Initiate Clock Switch to Primary Oscillator with PLL (NOSC=0b011) __builtin_write_OSCCONH(0x03); __builtin_write_OSCCONL(OSCCON | 0x01); // Wait for Clock switch to occur while (OSCCONbits.OSWEN!= 0); // Wait for PLL to lock while (OSCCONbits.LOCK!= 1); } Note: FPLLO = FPLLI * M/(N1 * N2 * N3); FPLLI = 10; M = 100; N1 = 1; N2 = 5; N3 = 1; so FPLLO = 10 * 100/(1 * 5 * 1) = 200 MHz or 50 MIPS.  2017-2019 Microchip Technology Inc. DS70005319D-page 441 dsPIC33CH128MP508 FAMILY Example 6-5 illustrates code for using the PLL (60 MIPS) with the Primary Oscillator. EXAMPLE 6-5: CODE EXAMPLE FOR USING SLAVE PLL (60 MIPS) WITH PRIMARY OSCILLATOR (POSC) //code example for 60 MIPS system clock using POSC with 10 MHz external crystal // Select Internal FRC at POR // Select FRC on POR #pragma config S1FNOSC = FRC // Oscillator Source Selection (Internal Fast RC (FRC)) #pragma config S1IESO = OFF // Two-speed Oscillator Start-up Enable bit (Start up with user-selected oscillator source) // Enable Clock Switching #pragma config S1FCKSM = CSECMD //Configure POSC in XT mode in Master core FOSC configuration register #pragma config POSCMD = XT int { main() // Configure PLL prescaler, both PLL postscalers, and PLL feedback divider CLKDIVbits.PLLPRE = 1; // N1=1 PLLFBDbits.PLLFBDIV = 120; // M = 120 PLLDIVbits.POST1DIV = 5; // N2=5 PLLDIVbits.POST2DIV = 1; // N3=1 // Initiate Clock Switch to Primary Oscillator with PLL (NOSC=0b011) __builtin_write_OSCCONH(0x03); __builtin_write_OSCCONL(OSCCON | 0x01); // Wait for Clock switch to occur while (OSCCONbits.OSWEN!= 0); // Wait for PLL to lock while (OSCCONbits.LOCK!= 1); } Note: FPLLO = FPLLI * M/(N1 * N2 * N3); FPLLI = 10; M = 120; N1 = 1; N2 = 5; N3 = 1; so FPLLO = 10 * 120/(1 * 5 * 1) = 240 MHz or 60 MIPS. DS70005319D-page 442  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY Example 6-6 illustrates code for using the Master PLL with an 8 MHz internal FRC. EXAMPLE 6-6: CODE EXAMPLE FOR USING MASTER PLL (50 MIPS) WITH 8 MHz INTERNAL FRC //code example for 50 MIPS system clock using 8MHz FRC // Select FRC on POR #pragma config FNOSC = FRC #pragma config IESO = OFF /// Enable Clock Switching #pragma config FCKSM = CSECMD int { // Oscillator Source Selection (Internal Fast RC (FRC)) main() // Configure PLL prescaler, both PLL postscalers, and PLL feedback divider CLKDIVbits.PLLPRE = 1; // N1=1 PLLFBDbits.PLLFBDIV = 125; // M = 125 PLLDIVbits.POST1DIV = 5; // N2=5 PLLDIVbits.POST2DIV = 1; // N3=1 // Initiate Clock Switch to FRC with PLL (NOSC=0b001) __builtin_write_OSCCONH(0x01); __builtin_write_OSCCONL(OSCCON | 0x01); // Wait for Clock switch to occur while (OSCCONbits.OSWEN!= 0); // Wait for PLL to lock while (OSCCONbits.LOCK!= 1); } Note: FPLLO = FPLLI * M/(N1 * N2 * N3); FPLLI = 8; M = 125; N1 = 1; N2 = 5; N3 = 1; so FPLLO = 8 * 125/(1 * 5 * 1) = 200 MHz or 50 MIPS.  2017-2019 Microchip Technology Inc. DS70005319D-page 443 dsPIC33CH128MP508 FAMILY Example 6-7 illustrates code for using the Slave PLL with an 8 MHz internal FRC. EXAMPLE 6-7: CODE EXAMPLE FOR USING SLAVE PLL (60 MIPS) WITH 8 MHz INTERNAL FRC //code example for 60 MIPS system clock using 8MHz FRC // Select FRC on POR #pragma config S1FNOSC = FRC #pragma config S1IESO = OFF // Oscillator Source Selection (Internal Fast RC (FRC)) // Two-speed Oscillator Start-up Enable bit (Start up with user-selected oscillator source) // Enable Clock Switching #pragma config S1FCKSM = CSECMD int { main() // Configure PLL prescaler, both PLL postscalers, and PLL feedback divider CLKDIVbits.PLLPRE = 1; // N1=1 PLLFBDbits.PLLFBDIV = 150; // M = 150 PLLDIVbits.POST1DIV = 5; // N2=5 PLLDIVbits.POST2DIV = 1; // N3=1 // Initiate Clock Switch to FRC with PLL (NOSC=0b001) __builtin_write_OSCCONH(0x01); __builtin_write_OSCCONL(OSCCON | 0x01); // Wait for Clock switch to occur while (OSCCONbits.OSWEN!= 0); // Wait for PLL to lock while (OSCCONbits.LOCK!= 1); } Note: FPLLO = FPLLI * M/(N1 * N2 * N3); FPLLI = 8; M = 150; N1 = 1; N2 = 5; N3 = 1; so FPLLO = 8 * 150/(1 * 5 * 1) = 240 MHz or 60 MIPS. DS70005319D-page 444  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 6.10 Master Oscillator Configuration Registers Table 6-1 lists the configuration settings that select the device’s Master core oscillator source and operating mode at a POR. TABLE 6-1: CONFIGURATION BIT VALUES FOR CLOCK SELECTION FOR THE MASTER Oscillator Source Oscillator Mode FNOSC[2:0] Value POSCMD[1:0] Value(3) Notes S0 Fast RC Oscillator (FRC) 000 xx 1 S1 Fast RC Oscillator with PLL (FRCPLL) 001 xx 1 S2 Primary Oscillator (EC) 010 00 1 S2 Primary Oscillator (XT) 010 01 S2 Primary Oscillator (HS) 010 10 S3 Primary Oscillator with PLL (ECPLL) 011 00 S3 Primary Oscillator with PLL (XTPLL) 011 01 S3 Primary Oscillator with PLL (HSPLL) 011 10 S4 Reserved 100 xx S5 Low-Power RC Oscillator (LPRC) 101 xx S6 Backup FRC (BFRC) 110 xx 1 S7 Fast RC Oscillator with ÷ N Divider (FRCDIVN) 111 xx 1, 2 Note 1: 2: 3: 1 1 The OSCO pin function is determined by the OSCIOFNC Configuration bit. This is the default oscillator mode for an unprogrammed (erased) device. The POSCMDx bits are only available in the Master FOSC Configuration register.  2017-2019 Microchip Technology Inc. DS70005319D-page 445 dsPIC33CH128MP508 FAMILY 6.11 Slave Oscillator Configuration Registers Table 6-2 lists the configuration settings that select the device’s Slave core oscillator source and operating mode at a POR. TABLE 6-2: CONFIGURATION BIT VALUES FOR CLOCK SELECTION FOR THE SLAVE Oscillator Source Oscillator Mode S1FNOSC[2:0] Value POSCMD[1:0] Value(3) Notes S0 Fast RC Oscillator (FRC) 000 xx 1 S1 Fast RC Oscillator with PLL (FRCPLL) 001 xx 1 S2 Primary Oscillator (EC) 010 00 1 S2 Primary Oscillator (XT) 010 01 S2 Primary Oscillator (HS) 010 10 S3 Primary Oscillator with PLL (ECPLL) 011 00 S3 Primary Oscillator with PLL (XTPLL) 011 01 S3 Primary Oscillator with PLL (HSPLL) 011 10 S4 Reserved 100 xx 1 S5 Low-Power RC Oscillator (LPRC) 101 xx 1 S6 Backup FRC (BFRC) 110 xx 1 Fast RC Oscillator with ÷ N Divider (FRCDIVN) 111 xx 1, 2 S7 Note 1: 2: 3: The OSCO pin function is determined by the S1OSCIOFNC Configuration bit. If both the Master core OSCIOFNC and Slave core S1OSCIOFNC bits are set, the Master core OSCIOFNC bit has priority. This is the default oscillator mode for an unprogrammed (erased) device. The POSCMD[1:0] bits are only available in the Master Oscillator Configuration register, FOSC. This setting configures the Primary Oscillator for use by either core. TABLE 6-3: OSCO FUNCTION FOR THE MASTER AND SLAVE CORE(1) [OSCIOFNC:S1OSCIOFNC] Note 1: 1 RB1 or OSCO pin function 1:1 Master clock output on OSCO pin 1:0 Master clock output on OSCO pin 0:1 Slave clock output on OSCO pin 1:1 Clock out disabled, RB1 works as an I/O port; output function is based on pin ownership (CPRB1 = 1 or 0) The RB1 pin will toggle during programming or debugging time, irrespective of the OSCIOFNC or S1OSCIOFNC settings. DS70005319D-page 446  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 6.12 Master Special Function Registers These Special Function Registers provide run-time control and status of the Master core’s oscillator system. 6.12.1 MASTER OSCILLATOR CONTROL REGISTERS OSCCON: OSCILLATOR CONTROL REGISTER (MASTER)(1) REGISTER 6-1: U-0 R-0 — COSC2 R-0 COSC1 R-0 COSC0 U-0 — R/W-y NOSC2 (2) R/W-y NOSC1 (2) R/W-y NOSC0(2) bit 15 bit 8 R/W-0 U-0 — CLKLOCK R-0 LOCK U-0 R/W-0 U-0 U-0 R/W-0 — CF(3) — — OSWEN bit 7 bit 0 Legend: y = Value set from Configuration bits on POR R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 COSC[2:0]: Current Oscillator Selection bits (read-only) 111 = Fast RC Oscillator (FRC) with Divide-by-n (FRCDIVN) 110 = Backup FRC (BFRC) 101 = Low-Power RC Oscillator (LPRC) 100 = Reserved – default to FRC 011 = Primary Oscillator (XT, HS, EC) with PLL (XTPLL, HSPLL, ECPLL) 010 = Primary Oscillator (XT, HS, EC) 001 = Fast RC Oscillator (FRC) with PLL (FRCPLL) 000 = Fast RC Oscillator (FRC) bit 11 Unimplemented: Read as ‘0’ bit 10-8 NOSC[2:0]: New Oscillator Selection bits(2) 111 = Fast RC Oscillator (FRC) with Divide-by-n (FRCDIVN) 110 = Backup FRC (BFRC) 101 = Low-Power RC Oscillator (LPRC) 100 = Reserved – default to FRC 011 = Primary Oscillator (XT, HS, EC) with PLL (XTPLL, HSPLL, ECPLL) 010 = Primary Oscillator (XT, HS, EC) 001 = Fast RC Oscillator (FRC) with PLL (FRCPLL) 000 = Fast RC Oscillator (FRC) bit 7 CLKLOCK: Clock Lock Enable bit 1 = If (FCKSM0 = 1), then clock and PLL configurations are locked; if (FCKSM0 = 0), then clock and PLL configurations may be modified 0 = Clock and PLL selections are not locked, configurations may be modified bit 6 Unimplemented: Read as ‘0’ Note 1: 2: 3: Writes to this register require an unlock sequence. Direct clock switches between any Primary Oscillator mode with PLL and FRCPLL mode are not permitted. This applies to clock switches in either direction. In these instances, the application must switch to FRC mode as a transitional clock source between the two PLL modes. This bit should only be cleared in software. Setting the bit in software (= 1) will have the same effect as an actual oscillator failure and will trigger an oscillator failure trap.  2017-2019 Microchip Technology Inc. DS70005319D-page 447 dsPIC33CH128MP508 FAMILY REGISTER 6-1: OSCCON: OSCILLATOR CONTROL REGISTER (MASTER)(1) (CONTINUED) bit 5 LOCK: PLL Lock Status bit (read-only) 1 = Indicates that PLL is in lock or PLL start-up timer is satisfied 0 = Indicates that PLL is out of lock, start-up timer is in progress or PLL is disabled bit 4 Unimplemented: Read as ‘0’ bit 3 CF: Clock Fail Detect bit(3) 1 = FSCM has detected a clock failure 0 = FSCM has not detected a clock failure bit 2-1 Unimplemented: Read as ‘0’ bit 0 OSWEN: Oscillator Switch Enable bit 1 = Requests oscillator switch to the selection specified by the NOSC[2:0] bits 0 = Oscillator switch is complete Note 1: 2: 3: Writes to this register require an unlock sequence. Direct clock switches between any Primary Oscillator mode with PLL and FRCPLL mode are not permitted. This applies to clock switches in either direction. In these instances, the application must switch to FRC mode as a transitional clock source between the two PLL modes. This bit should only be cleared in software. Setting the bit in software (= 1) will have the same effect as an actual oscillator failure and will trigger an oscillator failure trap. DS70005319D-page 448  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 6-2: CLKDIV: CLOCK DIVIDER REGISTER (MASTER) R/W-0 R/W-0 R/W-1 R/W-1 R/W-0 R/W-0 R/W-0 R/W-0 ROI DOZE2(1) DOZE1(1) DOZE0(1) DOZEN(2,3) FRCDIV2 FRCDIV1 FRCDIV0 bit 15 bit 8 U-0 U-0 r-0 r-0 — — — — R/W-0 R/W-0 R/W-0 R/W-1 PLLPRE[3:0](4) bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ROI: Recover on Interrupt bit 1 = Interrupts will clear the DOZEN bit and the processor clock, and the peripheral clock ratio is set to 1:1 0 = Interrupts have no effect on the DOZEN bit bit 14-12 DOZE[2:0]: Processor Clock Reduction Select bits(1) 111 = FP divided by 128 110 = FP divided by 64 101 = FP divided by 32 100 = FP divided by 16 011 = FP divided by 8 (default) 010 = FP divided by 4 001 = FP divided by 2 000 = FP divided by 1 bit 11 DOZEN: Doze Mode Enable bit(2,3) 1 = DOZE[2:0] field specifies the ratio between the peripheral clocks and the processor clocks 0 = Processor clock and peripheral clock ratio is forced to 1:1 bit 10-8 FRCDIV[2:0]: Internal Fast RC Oscillator Postscaler bits 111 = FRC divided by 256 110 = FRC divided by 64 101 = FRC divided by 32 100 = FRC divided by 16 011 = FRC divided by 8 010 = FRC divided by 4 001 = FRC divided by 2 000 = FRC divided by 1 (default) bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 Reserved: Read as ‘0’ Note 1: 2: 3: 4: The DOZE[2:0] bits can only be written to when the DOZEN bit is clear. If DOZEN = 1, any writes to DOZE[2:0] are ignored. This bit is cleared when the ROI bit is set and an interrupt occurs. The DOZEN bit cannot be set if DOZE[2:0] = 000. If DOZE[2:0] = 000, any attempt by user software to set the DOZEN bit is ignored. PLLPRE[3:0] may be updated while the PLL is operating, but the VCO may overshoot.  2017-2019 Microchip Technology Inc. DS70005319D-page 449 dsPIC33CH128MP508 FAMILY REGISTER 6-2: CLKDIV: CLOCK DIVIDER REGISTER (MASTER) (CONTINUED) PLLPRE[3:0]: PLL Phase Detector Input Divider Select bits (also denoted as ‘N1’, PLL prescaler)(4) 11111 = Reserved ... 1001 = Reserved 1000 = Input divided by 8 0111 = Input divided by 7 0110 = Input divided by 6 0101 = Input divided by 5 0100 = Input divided by 4 0011 = Input divided by 3 0010 = Input divided by 2 0001 = Input divided by 1 (power-on default selection) 0000 = Reserved bit 3-0 Note 1: 2: 3: 4: The DOZE[2:0] bits can only be written to when the DOZEN bit is clear. If DOZEN = 1, any writes to DOZE[2:0] are ignored. This bit is cleared when the ROI bit is set and an interrupt occurs. The DOZEN bit cannot be set if DOZE[2:0] = 000. If DOZE[2:0] = 000, any attempt by user software to set the DOZEN bit is ignored. PLLPRE[3:0] may be updated while the PLL is operating, but the VCO may overshoot. DS70005319D-page 450  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 6-3: PLLFBD: PLL FEEDBACK DIVIDER REGISTER (MASTER) U-0 U-0 U-0 U-0 r-0 r-0 r-0 r-0 — — — — — — — — bit 15 bit 8 R/W-1 R/W-0 R/W-0 R/W-1 R/W-0 R/W-1 R/W-1 R/W-0 PLLFBDIV[7:0] bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-12 Unimplemented: Read as ‘0’ bit 11-8 Reserved: Maintain as ‘0’ bit 7-0 PLLFBDIV[7:0]: PLL Feedback Divider bits (also denoted as ‘M’, PLL multiplier) 11111111 = Reserved ... 11001000 = 200 Maximum(1) ... 10010110 = 150 (default) ... 00010000 = 16 Minimum(1) ... 00000010 = Reserved 00000001 = Reserved 00000000 = Reserved Note 1: The allowed range is 16-200 (decimal). The rest of the values are reserved and should be avoided. The power on the default feedback divider is 150 (decimal) with an 8 MHz FRC input clock. The VCO frequency is 1.2 GHz.  2017-2019 Microchip Technology Inc. DS70005319D-page 451 dsPIC33CH128MP508 FAMILY REGISTER 6-4: OSCTUN: FRC OSCILLATOR TUNING REGISTER (MASTER) U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TUN[5:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-6 Unimplemented: Read as ‘0’ bit 5-0 TUN[5:0]: FRC Oscillator Tuning bits 011111 = Maximum frequency deviation of 1.74% (MHz) 011110 = Center frequency + 1.693% (MHz) ... 000001 = Center frequency + 0.047% (MHz) 000000 = Center frequency (8.00 MHz nominal) 111111 = Center frequency – 0.047% (MHz) ... 100001 = Center frequency – 1.693% (MHz) 100000 = Minimum frequency deviation of -1.74% (MHz) DS70005319D-page 452 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 6-5: PLLDIV: PLL OUTPUT DIVIDER REGISTER (MASTER) U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — R/W-0 R/W-0 VCODIV[1:0] bit 15 U-0 bit 8 R/W-1 R/W-0 R/W-0 U-0 POST1DIV[2:0](1,2) — R/W-0 — R/W-0 R/W-1 POST2DIV[2:0](1,2) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-10 Unimplemented: Read as ‘0’ bit 9-8 VCODIV[1:0]: PLL VCO Output Divider Select bits 11 = FVCO 10 = FVCO/2 01 = FVCO/3 00 = FVCO/4 bit 7 Unimplemented: Read as ‘0’ bit 6-4 POST1DIV[2:0]: PLL Output Divider #1 Ratio bits(1,2) POST1DIV[2:0] can have a valid value, from 1 to 7 (POST1DIVx value should be greater than or equal to the POST2DIVx value). The POST1DIVx divider is designed to operate at higher clock rates than the POST2DIVx divider. bit 3 Unimplemented: Read as ‘0’ bit 2-0 POST2DIV[2:0]: PLL Output Divider #2 Ratio bits(1,2) POST2DIV[2:0] can have a valid value, from 1 to 7 (POST2DIVx value should be less than or equal to the POST1DIVx value). The POST1DIVx divider is designed to operate at higher clock rates than the POST2DIVx divider. Note 1: 2: The POST1DIVx and POST2DIVx divider values must not be changed while the PLL is operating. The default values for POST1DIVx and POST2DIVx are 4 and 1, respectively, yielding a 150 MHz system source clock.  2017-2019 Microchip Technology Inc. DS70005319D-page 453 dsPIC33CH128MP508 FAMILY REGISTER 6-6: ACLKCON1: AUXILIARY CLOCK CONTROL REGISTER (MASTER) R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0 R/W-0 APLLEN(1) APLLCK — — — — — FRCSEL bit 15 bit 8 U-0 U-0 r-0 r-0 — — — — R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 APLLEN: Auxiliary PLL Enable/Bypass select bit(1) 1 = AFPLLO is connected to the APLL post-divider output (bypass disabled) 0 = AFPLLO is connected to the APLL input clock (bypass enabled) bit 14 APLLCK: APLL Phase-Locked State Status bit 1 = Auxiliary PLL is in lock 0 = Auxiliary PLL is not in lock bit 13-9 Unimplemented: Read as ‘0’ bit 8 FRCSEL: FRC Clock Source Select bit 1 = FRC is the clock source for APLL 0 = Primary Oscillator is the clock source for APLL bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 Reserved: Maintain as ‘0’ bit 3-0 APLLPRE[3:0]: Auxiliary PLL Phase Detector Input Divider bits 1111 = Reserved ... 1001 = Reserved 1000 = Input divided by 8 0111 = Input divided by 7 0110 = Input divided by 6 0101 = Input divided by 5 0100 = Input divided by 4 0011 = Input divided by 3 0010 = Input divided by 2 0001 = Input divided by 1 (power-on default selection) 0000 = Reserved Note 1: R/W-1 APLLPRE[3:0] Even with the APLLEN bit set, another peripheral must generate a clock request before the APLL will start. DS70005319D-page 454  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 6-7: APLLFBD1: APLL FEEDBACK DIVIDER REGISTER (MASTER) U-0 U-0 U-0 U-0 r-0 r-0 r-0 r-0 — — — — — — — — bit 15 bit 8 R/W-1 R/W-0 R/W-0 R/W-1 R/W-0 R/W-1 R/W-1 R/W-0 APLLFBDIV[7:0] bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-12 Unimplemented: Read as ‘0’ bit 11-8 Reserved: Maintain as ‘0’ bit 7-0 APLLFBDIV[7:0]: APLL Feedback Divider bits 11111111 = Reserved ... 11001000 = 200 maximum(1) ... 10010110 = 150 (default) ... 00010000 = 16 minimum(1) ... 00000010 = Reserved 00000001 = Reserved 00000000 = Reserved Note 1: x = Bit is unknown The allowed range is 16-200 (decimal). The rest of the values are reserved and should be avoided. The power-on default feedback divider is 150 (decimal) with an 8 MHz FRC input clock; the VCO frequency is 1.2 GHz.  2017-2019 Microchip Technology Inc. DS70005319D-page 455 dsPIC33CH128MP508 FAMILY REGISTER 6-8: APLLDIV1: APLL OUTPUT DIVIDER REGISTER (MASTER) U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — R/W-0 R/W-0 AVCODIV[1:0] bit 15 bit 8 U-0 R/W-1 R/W-0 APOST1DIV[2:0](1,2) — R/W-0 U-0 R/W-0 — R/W-0 R/W-1 APOST2DIV[2:0](1,2) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-10 Unimplemented: Read as ‘0’ bit 9-8 AVCODIV[1:0]: APLL VCO Output Divider Select bits 11 = AFVCO 10 = AFVCO/2 01 = AFVCO/3 00 = AFVCO/4 bit 7 Unimplemented: Read as ‘0’ bit 6-4 APOST1DIV[2:0]: APLL Output Divider #1 Ratio bits(1,2) APOST1DIV[2:0] can have a valid value, from 1 to 7 (the APOST1DIVx value should be greater than or equal to the APOST2DIVx value). The APOST1DIVx divider is designed to operate at higher clock rates than the APOST2DIVx divider. bit 3 Unimplemented: Read as ‘0’ bit 2-0 APOST2DIV[2:0]: APLL Output Divider #2 Ratio bits(1,2) APOST2DIV[2:0] can have a valid value, from 1 to 7 (the APOST2DIVx value should be less than or equal to the APOST1DIVx value). The APOST1DIVx divider is designed to operate at higher clock rates than the APOST2DIVx divider. Note 1: 2: The APOST1DIVx and APOST2DIVx values must not be changed while the PLL is operating. The default values for APOST1DIVx and APOST2DIVx are 4 and 1, respectively, yielding a 150 MHz system source clock. DS70005319D-page 456  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 6-9: CANCLKCON: CAN CLOCK CONTROL REGISTER R/W-0 U-0 U-0 U-0 CANCLKEN — — — R/W-0 R/W-0 R/W-0 R/W-0 CANCLKSEL[3:0](1) bit 15 bit 8 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CANCLKDIV[6:0](2,3) — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 CANCLKEN: Enables the CAN Clock Generator bit 1 = CAN clock generation circuitry is enabled 0 = CAN clock generation circuitry is disabled bit 14-12 Unimplemented: Read as ‘0’ bit 11-8 CANCLKSEL[3:0]: CAN Clock Source Select bits(1) 1011-1111 = Reserved (no clock selected) 1010 = AFVCO/4 1001 = AFVCO/3 1000 = AFVCO/2 0111 = AFVCO 0110 = AFPLLO 0101 = FVCO/4 0100 = FVCO/3 0011 = FVCO/2 0010 = FPLLO 0001 = FVCO 0000 = 0 (no clock selected) bit 7 Unimplemented: Read as ‘0’ bit 6-0 CANCLKDIV[6:0]: CAN Clock Divider Select bits(2,3) 1111111 = Divide-by-128 ... 0000010 = Divide-by-3 0000001 = Divide-by-2 0000000 = Divide-by-1 Note 1: 2: 3: x = Bit is unknown The user must ensure the input clock source is 640 MHz or less. Operation with input reference frequency above 640 MHz will result in unpredictable behavior. The CANCLKDIVx divider value must not be changed during CAN module operation. The user must ensure the maximum clock output frequency of the divider is 80 MHz or less.  2017-2019 Microchip Technology Inc. DS70005319D-page 457 dsPIC33CH128MP508 FAMILY REGISTER 6-10: REFOCONL: REFERENCE CLOCK CONTROL LOW REGISTER (MASTER) R/W-0 U-0 R/W-0 R/W-0 R/W-0 U-0 HC/R/W-0 HSC/R-0 ROEN — ROSIDL ROOUT ROSLP — ROSWEN ROACTIV bit 15 bit 8 U-0 U-0 U-0 U-0 — — — — R/W-0 R/W-0 R/W-0 R/W-0 ROSEL[3:0] bit 7 bit 0 Legend: HC = Hardware Clearable bit HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ROEN: Reference Clock Enable bit 1 = Reference Oscillator is enabled on the REFCLKO pin 0 = Reference Oscillator is disabled bit 14 Unimplemented: Read as ‘0’ bit 13 ROSIDL: Reference Clock Stop in Idle bit 1 = Reference Oscillator continues to run in Idle mode 0 = Reference Oscillator is disabled in Idle mode bit 12 ROOUT: Reference Clock Output Enable bit 1 = Reference clock external output is enabled and available on the REFCLKO pin 0 = Reference clock external output is disabled bit 11 ROSLP: Reference Clock Stop in Sleep bit 1 = Reference Oscillator continues to run in Sleep modes 0 = Reference Oscillator is disabled in Sleep modes bit 10 Unimplemented: Read as ‘0’ bit 9 ROSWEN: Reference Clock Output Enable bit 1 = Clock divider change (requested by changes to RODIVx) is requested or is in progress (set in software, cleared by hardware upon completion) 0 = Clock divider change has completed or is not pending bit 8 ROACTIV: Reference Clock Status bit 1 = Reference clock is active; do not change clock source 0 = Reference clock is stopped; clock source and configuration may be safely changed bit 7-4 Unimplemented: Read as ‘0’ bit 3-0 ROSEL[3:0]: Reference Clock Source Select bits 1111 = Reserved ... = Reserved 1000 = Reserved 0111 = REFOI (PPS) pin 0110 = FVCO/4 0101 = BFRC 0100 = LPRC 0011 = FRC 0010 = Primary Oscillator 0001 = Peripheral clock (FP) 0000 = System clock (FOSC) DS70005319D-page 458  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 6-11: U-0 REFOCONH: REFERENCE CLOCK CONTROL HIGH REGISTER (MASTER) R/W-0 R/W-0 R/W-0 — R/W-0 R/W-0 R/W-0 R/W-0 RODIV[14:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RODIV[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-0 RODIV[14:0]: Reference Clock Integer Divider Select bits Divider for the selected input clock source is two times the selected value. 111 1111 1111 1111 = Base clock value divided by 65,534 (2 * 7FFFh) 111 1111 1111 1110 = Base clock value divided by 65,532 (2 * 7FFEh) 111 1111 1111 1101 = Base clock value divided by 65,530 (2 * 7FFDh) ... 000 0000 0000 0010 = Base clock value divided by 4 (2 * 2) 000 0000 0000 0001 = Base clock value divided by 2 (2 * 1) 000 0000 0000 0000 = Base clock value REGISTER 6-12: R/W-0 REFOTRIM: REFERENCE OSCILLATOR TRIM REGISTER (MASTER) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ROTRIM[8:1] bit 15 bit 8 R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 ROTRIM0 — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-7 ROTRIM[8:0]: REFO Trim bits These bits provide a fractional additive to the RODIV[14:0] value for the 1/2 period of the REFO clock. 000000000 = 0/512 (0.0 divisor added to the RODIV[14:0] value) 000000001 = 1/512 (0.001953125 divisor added to the RODIV[14:0] value) 000000010 = 2/512 (0.00390625 divisor added to the RODIV[14:0] value) ... 100000000 = 256/512 (0.5000 divisor added to the RODIV[14:0] value) ... 111111110 = 510/512 (0.99609375 divisor added to the RODIV[14:0] value) 111111111 = 511/512 (0.998046875 divisor added to the RODIV[14:0] value) bit 6-0 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. DS70005319D-page 459 dsPIC33CH128MP508 FAMILY 6.13 Slave Special Function Registers These Special Function Registers provide run-time control and status of the Slave core’s oscillator system. 6.13.1 SLAVE OSCILLATOR CONTROL REGISTERS OSCCON: OSCILLATOR CONTROL REGISTER (SLAVE)(1) REGISTER 6-13: U-0 R-0 — COSC2 R-0 COSC1 R-0 COSC0 U-0 — R/W-y NOSC2 (2) R/W-y NOSC1 (2) R/W-y NOSC0(2) bit 15 bit 8 R/W-0 U-0 R-0 U-0 R/W-0 U-0 U-0 R/W-0 CLKLOCK — LOCK — CF(3) — — OSWEN bit 7 bit 0 Legend: y = Value Set from Configuration bits on POR R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 COSC[2:0]: Current Oscillator Selection bits (read-only) 111 = Fast RC Oscillator (FRC) with Divide-by-n (FRCDIVN) 110 = Backup FRC (BFRC) 101 = Low-Power RC Oscillator (LPRC) 100 = Reserved 011 = Primary Oscillator (XT, HS, EC) with PLL (XTPLL, HSPLL, ECPLL) 010 = Primary Oscillator (XT, HS, EC) 001 = Fast RC Oscillator (FRC) with PLL (FRCPLL) 000 = Fast RC Oscillator (FRC) bit 11 Unimplemented: Read as ‘0’ bit 10-8 NOSC[2:0]: New Oscillator Selection bits(2) 111 = Fast RC Oscillator (FRC) with Divide-by-n (FRCDIVN) 110 = Backup FRC (BFRC) 101 = Low-Power RC Oscillator (LPRC) 100 = Reserved 011 = Primary Oscillator (XT, HS, EC) with PLL (XTPLL, HSPLL, ECPLL) 010 = Primary Oscillator (XT, HS, EC) 001 = Fast RC Oscillator (FRC) with PLL (FRCPLL) 000 = Fast RC Oscillator (FRC) bit 7 CLKLOCK: Clock Lock Enable bit 1 = If (FCKSM0 = 1), then clock and PLL configurations are locked; if (FCKSM0 = 0), then clock and PLL configurations may be modified 0 = Clock and PLL selections are not locked, configurations may be modified bit 6 Unimplemented: Read as ‘0’ Note 1: 2: 3: Writes to this register require an unlock sequence. Direct clock switches between any Primary Oscillator mode with PLL and FRCPLL mode are not permitted. This applies to clock switches in either direction. In these instances, the application must switch to FRC mode as a transitional clock source between the two PLL modes. This bit should only be cleared in software. Setting the bit in software (= 1) will have the same effect as an actual oscillator failure and will trigger an oscillator failure trap. DS70005319D-page 460  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 6-13: OSCCON: OSCILLATOR CONTROL REGISTER (SLAVE)(1) (CONTINUED) bit 5 LOCK: PLL Lock Status bit (read-only) 1 = Indicates that PLL is in lock or PLL start-up timer is satisfied 0 = Indicates that PLL is out of lock, start-up timer is in progress or PLL is disabled bit 4 Unimplemented: Read as ‘0’ bit 3 CF: Clock Fail Detect bit(3) 1 = FSCM has detected a clock failure 0 = FSCM has not detected a clock failure bit 2-1 Unimplemented: Read as ‘0’ bit 0 OSWEN: Oscillator Switch Enable bit 1 = Requests oscillator switch to the selection specified by the NOSC[2:0] bits 0 = Oscillator switch is complete Note 1: 2: 3: Writes to this register require an unlock sequence. Direct clock switches between any Primary Oscillator mode with PLL and FRCPLL mode are not permitted. This applies to clock switches in either direction. In these instances, the application must switch to FRC mode as a transitional clock source between the two PLL modes. This bit should only be cleared in software. Setting the bit in software (= 1) will have the same effect as an actual oscillator failure and will trigger an oscillator failure trap.  2017-2019 Microchip Technology Inc. DS70005319D-page 461 dsPIC33CH128MP508 FAMILY REGISTER 6-14: CLKDIV: CLOCK DIVIDER REGISTER (SLAVE) R/W-0 R/W-0 R/W-1 R/W-1 R/W-0 R/W-0 R/W-0 R/W-0 ROI DOZE2(1) DOZE1(1) DOZE0(1) DOZEN(2,3) FRCDIV2 FRCDIV1 FRCDIV0 bit 15 bit 8 U-0 U-0 r-0 r-0 — — — — R/W-0 R/W-0 R/W-0 R/W-0 PLLPRE[3:0](4) bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ROI: Recover on Interrupt bit 1 = Interrupts will clear the DOZEN bit and the processor clock, and the peripheral clock ratio is set to 1:1 0 = Interrupts have no effect on the DOZEN bit bit 14-12 DOZE[2:0]: Processor Clock Reduction Select bits(1) 111 = FP divided by 128 110 = FP divided by 64 101 = FP divided by 32 100 = FP divided by 16 011 = FP divided by 8 (default) 010 = FP divided by 4 001 = FP divided by 2 000 = FP divided by 1 bit 11 DOZEN: Doze Mode Enable bit(2,3) 1 = DOZE[2:0] field specifies the ratio between the peripheral clocks and the processor clocks 0 = Processor clock and peripheral clock ratio is forced to 1:1 bit 10-8 FRCDIV[2:0]: Internal Fast RC Oscillator Postscaler bits 111 = FRC divided by 256 110 = FRC divided by 64 101 = FRC divided by 32 100 = FRC divided by 16 011 = FRC divided by 8 010 = FRC divided by 4 001 = FRC divided by 2 000 = FRC divided by 1 (default) bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 Reserved: Read as ‘0’ Note 1: 2: 3: 4: The DOZE[2:0] bits can only be written to when the DOZEN bit is clear. If DOZEN = 1, any writes to DOZE[2:0] are ignored. This bit is cleared when the ROI bit is set and an interrupt occurs. The DOZEN bit cannot be set if DOZE[2:0] = 000. If DOZE[2:0] = 000, any attempt by user software to set the DOZEN bit is ignored. PLLPRE[3:0] may be updated while the PLL is operating, but the VCO may overshoot. DS70005319D-page 462  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 6-14: CLKDIV: CLOCK DIVIDER REGISTER (SLAVE) (CONTINUED) PLLPRE[3:0]: PLL Phase Detector Input Divider Select bits (also denoted as ‘N1’, PLL prescaler)(4) 11111 = Reserved ... 1001 = Reserved 1000 = Input divided by 8 0111 = Input divided by 7 0110 = Input divided by 6 0101 = Input divided by 5 0100 = Input divided by 4 0011 = Input divided by 3 0010 = Input divided by 2 0001 = Input divided by 1 (power-on default selection) 0000 = Reserved bit 3-0 Note 1: 2: 3: 4: The DOZE[2:0] bits can only be written to when the DOZEN bit is clear. If DOZEN = 1, any writes to DOZE[2:0] are ignored. This bit is cleared when the ROI bit is set and an interrupt occurs. The DOZEN bit cannot be set if DOZE[2:0] = 000. If DOZE[2:0] = 000, any attempt by user software to set the DOZEN bit is ignored. PLLPRE[3:0] may be updated while the PLL is operating, but the VCO may overshoot.  2017-2019 Microchip Technology Inc. DS70005319D-page 463 dsPIC33CH128MP508 FAMILY REGISTER 6-15: PLLFBD: PLL FEEDBACK DIVIDER REGISTER (SLAVE) U-0 U-0 U-0 U-0 r-0 r-0 r-0 r-0 — — — — — — — — bit 15 bit 8 R/W-1 R/W-0 R/W-0 R/W-1 R/W-0 R/W-1 R/W-1 R/W-0 PLLFBDIV[7:0] bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-12 Unimplemented: Read as ‘0’ bit 11-8 Reserved: Maintain as ‘0’ bit 7-0 PLLFBDIV[7:0]: PLL Feedback Divider bits (also denoted as ‘M’, PLL multiplier) 11111111 = Reserved ... 11001000 = 200 maximum(1) ... 10010110 = 150 (default) ... 00010000 = 16 minimum(1) ... 00000010 = Reserved 00000001 = Reserved 00000000 = Reserved Note 1: The allowed range is 16-200 (decimal). The rest of the values are reserved and should be avoided. The power on the default feedback divider is 150 (decimal) with an 8 MHz FRC input clock. The VCO frequency is 1.2 GHz. DS70005319D-page 464  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 6-16: PLLDIV: PLL OUTPUT DIVIDER REGISTER (SLAVE) U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — R/W-0 R/W-0 VCODIV[1:0] bit 15 bit 8 U-0 R/W-1 R/W-0 POST1DIV[2:0](1,2) — R/W-0 U-0 R/W-0 — R/W-0 R/W-1 POST2DIV[2:0](1,2) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-10 Unimplemented: Read as ‘0’ bit 9-8 VCODIV[1:0]: PLL VCO Output Divider Select bits 11 = FVCO 10 = FVCO/2 01 = FVCO/3 00 = FVCO/4 bit 7 Unimplemented: Read as ‘0’ bit 6-4 POST1DIV[2:0]: PLL Output Divider #1 Ratio bits(1,2) POST1DIV[2:0] can have a valid value, from 1 to 7 (POST1DIVx value should be greater than or equal to the POST2DIVx value). The POST1DIVx divider is designed to operate at higher clock rates than the POST2DIVx divider. bit 3 Unimplemented: Read as ‘0’ bit 2-0 POST2DIV[2:0]: PLL Output Divider #2 Ratio bits(1,2) POST2DIV[2:0] can have a valid value, from 1 to 7 (POST2DIVx value should be less than or equal to the POST1DIVx value). The POST1DIVx divider is designed to operate at higher clock rates than the POST2DIVx divider. Note 1: 2: The POST1DIVx and POST2DIVx divider values must not be changed while the PLL is operating. The default values for POST1DIVx and POST2DIVx are 4 and 1, respectively, yielding a 150 MHz system source clock.  2017-2019 Microchip Technology Inc. DS70005319D-page 465 dsPIC33CH128MP508 FAMILY REGISTER 6-17: ACLKCON1: AUXILIARY CLOCK CONTROL REGISTER (SLAVE) R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0 R/W-0 APLLEN(1) APLLCK — — — — — FRCSEL bit 15 bit 8 U-0 U-0 r-0 r-0 — — — — R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 APLLEN: Auxiliary PLL Enable/Bypass Select bit(1) 1 = AFPLLO is connected to APLL post-divider output (bypass is disabled) 0 = AFPLLO is connected to APLL input clock (bypass is enabled) bit 14 APLLCK: APLL Phase-Locked State Status bit 1 = Auxiliary PLL is in lock 0 = Auxiliary PLL is not in lock bit 13-9 Unimplemented: Read as ‘0’ bit 8 FRCSEL: FRC Clock Source Select bit bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 Reserved: Read as ‘0’ bit 3-0 APLLPRE[3:0]: Auxiliary PLL Phase Detector Input Divider bits 111111 = Reserved ... 1001 = Reserved 1000 = Input divided by 8 0111 = Input divided by 7 0110 = Input divided by 6 0101 = Input divided by 5 0100 = Input divided by 4 0011 = Input divided by 3 0010 = Input divided by 2 0001 = Input divided by 1 (power-on default selection) 0000 = Reserved Note 1: R/W-0 APLLPRE[3:0] Even with the APLLEN bit set, another peripheral must generate a clock request before the APLL will start. DS70005319D-page 466  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 6-18: APLLFBD1: APLL FEEDBACK DIVIDER REGISTER (SLAVE) U-0 U-0 U-0 U-0 r-0 r-0 r-0 r-0 — — — — — — — — bit 15 bit 8 R/W-1 R/W-0 R/W-0 R/W-1 R/W-0 R/W-1 R/W-1 R/W-0 APLLFBDIV[7:0] bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-12 Unimplemented: Read as ‘0’ bit 11-8 Reserved: Maintain as ‘0’ bit 7-0 APLLFBDIV[7:0]: APLL Feedback Divider bits 11111111 = Reserved ... 11001000 = 200 maximum(1) ... 10010110 = 150 (default) ... 00010000 = 16 minimum(1) ... 00000010 = Reserved 00000001 = Reserved 00000000 = Reserved Note 1: x = Bit is unknown The allowed range is 16-200 (decimal). The rest of the values are reserved and should be avoided. The power-on default feedback divider is 150 (decimal) with an 8 MHz FRC input clock; the VCO frequency is 1.2 GHz.  2017-2019 Microchip Technology Inc. DS70005319D-page 467 dsPIC33CH128MP508 FAMILY REGISTER 6-19: APLLDIV: APLL OUTPUT DIVIDER REGISTER (SLAVE) U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — R/W-0 R/W-0 AVCODIV[1:0] bit 15 bit 8 U-0 R/W-1 R/W-0 APOST1DIV[2:0](1,2) — R/W-0 U-0 R/W-0 — R/W-0 R/W-1 APOST2DIV[2:0](1,2) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-10 Unimplemented: Read as ‘0’ bit 9-8 AVCODIV[1:0]: APLL VCO Output Divider Select bits 11 = AFVCO 10 = AFVCO/2 01 = AFVCO/3 00 = AFVCO/4 bit 7 Unimplemented: Read as ‘0’ bit 6-4 APOST1DIV[2:0]: APLL Output Divider #1 Ratio bits(1,2) APOST1DIV[2:0] can have a valid value, from 1 to 7 (APOST1DIVx value should be greater than or equal to the APOST2DIVx value). The APOST1DIVx divider is designed to operate at higher clock rates than the APOST2DIVx divider. bit 3 Unimplemented: Read as ‘0’ bit 2-0 APOST2DIV[2:0]: APLL Output Divider #2 Ratio bits(1,2) APOST2DIV[2:0] can have a valid value, from 1 to 7 (APOST2DIVx value should be less than or equal to the APOST1DIVx value). The APOST1DIVx divider is designed to operate at higher clock rates than the APOST2DIVx divider. Note 1: 2: The APOST1DIVx and APOST2DIVx divider values must not be changed while the PLL is operating. The default values for APOST1DIVx and APOST2DIVx are 4 and 1, respectively, yielding a 150 MHz system source clock. DS70005319D-page 468  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 6-20: REFOCONL: REFERENCE CLOCK CONTROL LOW REGISTER (SLAVE) R/W-0 U-0 R/W-0 R/W-0 R/W-0 U-0 HC/R/W-0 HSC/R-0 ROEN — ROSIDL ROOUT ROSLP — ROSWEN ROACTIV bit 15 bit 8 U-0 U-0 U-0 U-0 — — — — R/W-0 R/W-0 R/W-0 R/W-0 ROSEL[3:0] bit 7 bit 0 Legend: HC = Hardware Clearable bit HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ROEN: Reference Clock Enable bit 1 = Reference Oscillator is enabled on the REFCLKO pin 0 = Reference Oscillator is disabled bit 14 Unimplemented: Read as ‘0’ bit 13 ROSIDL: Reference Clock Stop in Idle bit 1 = Reference Oscillator is disabled in Idle mode 0 = Reference Oscillator continues to run in Idle mode bit 12 ROOUT: Reference Clock Output Enable bit 1 = Reference clock external output is enabled and available on the REFCLKO pin 0 = Reference clock external output is disabled bit 11 ROSLP: Reference Clock Stop in Sleep bit 1 = Reference Oscillator continues to run in Sleep modes 0 = Reference Oscillator is disabled in Sleep modes bit 10 Unimplemented: Read as ‘0’ bit 9 ROSWEN: Reference Clock Output Enable bit 1 = Clock divider change (requested by changes to RODIVx) is requested or is in progress (set in software, cleared by hardware upon completion) 0 = Clock divider change has completed or is not pending bit 8 ROACTIV: Reference Clock Status bit 1 = Reference clock is active; do not change clock source 0 = Reference clock is stopped; clock source and configuration may be safely changed bit 7-4 Unimplemented: Read as ‘0’ bit 3-0 ROSEL[3:0]: Reference Clock Source Select bits 1111 = ... = Reserved 1000 = Reserved 0111 = REFOI (PPS) pin 0110 = FVCO/4 0101 = BFRC 0100 = LPRC 0011 = FRC 0010 = Primary Oscillator 0001 = Peripheral clock (FP) 0000 = System clock (FOSC)  2017-2019 Microchip Technology Inc. DS70005319D-page 469 dsPIC33CH128MP508 FAMILY REGISTER 6-21: U-0 REFOCONH: REFERENCE CLOCK CONTROL HIGH REGISTER (SLAVE) R/W-0 R/W-0 R/W-0 — R/W-0 R/W-0 R/W-0 R/W-0 RODIV[14:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RODIV[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-0 RODIV[14:0]: Reference Clock Integer Divider Select bits Divider for the selected input clock source is two times the selected value. 111 1111 1111 1111 = Base clock value divided by 65,534 (2 * 7FFFh) 111 1111 1111 1110 = Base clock value divided by 65,532 (2 * 7FFEh) 111 1111 1111 1101 = Base clock value divided by 65,530 (2 * 7FFDh) ... 000 0000 0000 0010 = Base clock value divided by 4 (2 * 2) 000 0000 0000 0001 = Base clock value divided by 2 (2 * 1) 000 0000 0000 0000 = Base clock value DS70005319D-page 470  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 7.0 POWER-SAVING FEATURES (MASTER AND SLAVE) Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “Watchdog Timer and PowerSaving Modes” (www.microchip.com/ DS70615) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). The power saving section is only relevant for this device. The WDT has its own family reference manual section. 2: This chapter is applicable to both the Master core and the Slave core. There are registers associated with PMD that are listed separately for Master and Slave at the end of this section. Other features related to power saving that are discussed are applicable to both the Master and Slave core. 3: All associated register names are the same on the Master core and the Slave core. The Slave code will be developed in a separate project in MPLAB® X IDE with the device selection, dsPIC33CH128MP508S1, where S1 indicates the Slave device. The dsPIC33CH128MP508 family devices provide the ability to manage power consumption by selectively managing clocking to the CPU and the peripherals. In general, a lower clock frequency and a reduction in the number of peripherals being clocked constitutes lower consumed power. dsPIC33CH128MP508 family devices can manage power consumption in four ways: • • • • Clock Frequency Instruction-Based Sleep and Idle modes Software-Controlled Doze mode Selective Peripheral Control in Software Combinations of these methods can be used to selectively tailor an application’s power consumption while still maintaining critical application features, such as timing-sensitive communications. 7.1 Clock Frequency and Clock Switching The dsPIC33CH128MP508 family devices allow a wide range of clock frequencies to be selected under application control. If the system clock configuration is not locked, users can choose low-power or high-precision oscillators by simply changing the NOSCx bits (OSCCON[10:8]). The process of changing a system clock during operation, as well as limitations to the process, are discussed in more detail in Section 6.0 “Oscillator with High-Frequency PLL”. 7.2 Instruction-Based Power-Saving Modes The dsPIC33CH128MP508 family devices have two special power-saving modes that are entered through the execution of a special PWRSAV instruction. Sleep mode stops clock operation and halts all code execution. Idle mode halts the CPU and code execution, but allows peripheral modules to continue operation. The assembler syntax of the PWRSAV instruction is shown in Example 7-1. Note: SLEEP_MODE and IDLE_MODE are constants defined in the assembler include file for the selected device. Sleep and Idle modes can be exited as a result of an enabled interrupt, WDT time-out or a device Reset. When the device exits these modes, it is said to “wake-up”. EXAMPLE 7-1: PWRSAV INSTRUCTION SYNTAX PWRSAV #SLEEP_MODE PWRSAV #IDLE_MODE ; Put the device into Sleep mode ; Put the device into Idle mode  2017-2019 Microchip Technology Inc. DS70005319D-page 471 dsPIC33CH128MP508 FAMILY 7.2.1 SLEEP MODE 7.2.2 IDLE MODE The following occurs in Sleep mode: The following occurs in Idle mode: • The system clock source is shut down. If an on-chip oscillator is used, it is turned off. • The device current consumption is reduced to a minimum, provided that no I/O pin is sourcing current. • The Fail-Safe Clock Monitor does not operate, since the system clock source is disabled. • The LPRC clock continues to run in Sleep mode if the WDT is enabled. • The WDT, if enabled, is automatically cleared prior to entering Sleep mode. • Some device features or peripherals can continue to operate. This includes items such as the Input Change Notification on the I/O ports or peripherals that use an External Clock input. • Any peripheral that requires the system clock source for its operation is disabled. • The CPU stops executing instructions. • The WDT is automatically cleared. • The system clock source remains active. By default, all peripheral modules continue to operate normally from the system clock source, but can also be selectively disabled (see Section 7.4 “Peripheral Module Disable”). • If the WDT or FSCM is enabled, the LPRC also remains active. The device wakes up from Sleep mode on any of the these events: • Any interrupt source that is individually enabled • Any form of device Reset • A WDT time-out On wake-up from Sleep mode, the processor restarts with the same clock source that was active when Sleep mode was entered. For optimal power savings, the internal regulator and the Flash regulator can be configured to go into standby when Sleep mode is entered by clearing the VREGS (RCON[8]) bit. DS70005319D-page 472 The device wakes from Idle mode on any of these events: • Any interrupt that is individually enabled • Any device Reset • A WDT time-out On wake-up from Idle mode, the clock is reapplied to the CPU and instruction execution will begin (two-four clock cycles later), starting with the instruction following the PWRSAV instruction or the first instruction in the ISR. All peripherals also have the option to discontinue operation when Idle mode is entered to allow for increased power savings. This option is selectable in the control register of each peripheral; for example, the SIDL bit in the Timer1 Control register (T1CON[13]). 7.2.3 INTERRUPTS COINCIDENT WITH POWER SAVE INSTRUCTIONS Any interrupt that coincides with the execution of a PWRSAV instruction is held off until entry into Sleep or Idle mode has completed. The device then wakes up from Sleep or Idle mode.  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 7.3 Doze Mode The preferred strategies for reducing power consumption are changing clock speed and invoking one of the power-saving modes. In some circumstances, this cannot be practical. For example, it may be necessary for an application to maintain uninterrupted synchronous communication, even while it is doing nothing else. Reducing system clock speed can introduce communication errors, while using a power-saving mode can stop communications completely. Note 1: If a PMD bit is set, the corresponding module is disabled after a delay of one instruction cycle. Similarly, if a PMD bit is cleared, the corresponding module is enabled after a delay of one instruction cycle (assuming the module control registers are already configured to enable module operation). 2: The PMD bits are different for the Master core and Slave core. The Master has its own PMD bits which can be disabled/ enabled independently of the Slave peripherals. The Slave has its own PMD bits which can be disabled/enabled independently of the Master peripherals. The register names are the same for the Master and the Slave, but the PMD registers have different addresses in the Master and Slave SFR. Doze mode is a simple and effective alternative method to reduce power consumption while the device is still executing code. In this mode, the system clock continues to operate from the same source and at the same speed. Peripheral modules continue to be clocked at the same speed, while the CPU clock speed is reduced. Synchronization between the two clock domains is maintained, allowing the peripherals to access the SFRs while the CPU executes code at a slower rate. Doze mode is enabled by setting the DOZEN bit (CLKDIV[11]). The ratio between peripheral and core clock speed is determined by the DOZE[2:0] bits (CLKDIV[14:12]). There are eight possible configurations, from 1:1 to 1:128, with 1:1 being the default setting. Programs can use Doze mode to selectively reduce power consumption in event-driven applications. This allows clock-sensitive functions, such as synchronous communications, to continue without interruption while the CPU Idles, waiting for something to invoke an interrupt routine. An automatic return to full-speed CPU operation on interrupts can be enabled by setting the ROI bit (CLKDIV[15]). By default, interrupt events have no effect on Doze mode operation. 7.4 Peripheral Module Disable The Peripheral Module Disable (PMD) registers provide a method to disable a peripheral module by stopping all clock sources supplied to that module. When a peripheral is disabled using the appropriate PMD control bit, the peripheral is in a minimum power consumption state. The control and status registers associated with the peripheral are also disabled, so writes to those registers do not have any effect and read values are invalid. 7.5 Power-Saving Resources Many useful resources are provided on the main product page of the Microchip website for the devices listed in this data sheet. This product page contains the latest updates and additional information. 7.5.1 KEY RESOURCES • “Watchdog Timer and Power-Saving Modes” (www.microchip.com/DS70615) in the “dsPIC33/ PIC24 Family Reference Manual” • Code Samples • Application Notes • Software Libraries • Webinars • All related “dsPIC33/PIC24 Family Reference Manual” Sections • Development Tools A peripheral module is enabled only if both the associated bit in the PMD register is cleared and the peripheral is supported by the specific dsPIC® DSC variant. If the peripheral is present in the device, it is enabled in the PMD register by default.  2017-2019 Microchip Technology Inc. DS70005319D-page 473 dsPIC33CH128MP508 FAMILY 7.6 PMD Control Registers REGISTER 7-1: PMD1: MASTER PERIPHERAL MODULE DISABLE 1 CONTROL REGISTER LOW U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 U-0 — — — — T1MD QEIMD PWMMD — bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 I2C1MD U2MD U1MD SPI2MD SPI1MD — C1MD ADC1MD bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-12 Unimplemented: Read as ‘0’ bit 11 T1MD: Timer1 Module Disable bit 1 = Timer1 module is disabled 0 = Timer1 module is enabled bit 10 QEIMD: QEI Module Disable bit 1 = QEI module is disabled 0 = QEI module is enabled bit 9 PWMMD: PWM Module Disable bit 1 = PWM module is disabled 0 = PWM module is enabled bit 8 Unimplemented: Read as ‘0’ bit 7 I2C1MD: I2C1 Module Disable bit 1 = I2C1 module is disabled 0 = I2C1 module is enabled bit 6 U2MD: UART2 Module Disable bit 1 = UART2 module is disabled 0 = UART2 module is enabled bit 5 U1MD: UART1 Module Disable bit 1 = UART1 module is disabled 0 = UART1 module is enabled bit 4 SPI2MD: SPI2 Module Disable bit 1 = SPI2 module is disabled 0 = SPI2 module is enabled bit 3 SPI1MD: SPI1 Module Disable bit 1 = SPI1 module is disabled 0 = SPI1 module is enabled bit 2 Unimplemented: Read as ‘0’ bit 1 C1MD: CAN1 Module Disable bit 1 = CAN1 module is disabled 0 = CAN1 module is enabled bit 0 ADC1MD: ADC Module Disable bit 1 = ADC module is disabled 0 = ADC module is enabled DS70005319D-page 474 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 7-2: PMD2: MASTER PERIPHERAL MODULE DISABLE 2 CONTROL REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CCP8MD CCP7MD CCP6MD CCP5MD CCP4MD CCP3MD CCP2MD CCP1MD bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-8 Unimplemented: Read as ‘0’ bit 7 CCP8MD: SCCP8 Module Disable bit 1 = SCCP8 module is disabled 0 = SCCP8 module is enabled bit 6 CCP7MD: SCCP7 Module Disable bit 1 = SCCP7 module is disabled 0 = SCCP7 module is enabled bit 5 CCP6MD: SCCP6 Module Disable bit 1 = SCCP6 module is disabled 0 = SCCP6 module is enabled bit 4 CCP5MD: SCCP5 Module Disable bit 1 = SCCP5 module is disabled 0 = SCCP5 module is enabled bit 3 CCP4MD: SCCP4 Module Disable bit 1 = SCCP4 module is disabled 0 = SCCP4 module is enabled bit 2 CCP3MD: SCCP3 Module Disable bit 1 = SCCP3 module is disabled 0 = SCCP3 module is enabled bit 1 CCP2MD: SCCP2 Module Disable bit 1 = SCCP2 module is disabled 0 = SCCP2 module is enabled bit 0 CCP1MD: SCCP1 Module Disable bit 1 = SCCP1 module is disabled 0 = SCCP1 module is enabled  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 475 dsPIC33CH128MP508 FAMILY PMD3: MASTER PERIPHERAL MODULE DISABLE 3 CONTROL REGISTER LOW(1) REGISTER 7-3: U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — U-0 bit 15 bit 8 R/W-0 U-0 U-0 U-0 U-0 U-0 R/W-0 U-0 CRCMD — — — — — I2C2MD — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-8 Unimplemented: Read as ‘0’ bit 7 CRCMD: CRC Module Disable bit 1 = CRC module is disabled 0 = CRC module is enabled bit 6-2 Unimplemented: Read as ‘0’ bit 1 I2C2MD: I2C2 Module Disable bit 1 = I2C2 module is disabled 0 = I2C2 module is enabled bit 0 Unimplemented: Read as ‘0’ Note 1: x = Bit is unknown This register is only available in the Master core. DS70005319D-page 476  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 7-4: PMD4: MASTER PERIPHERAL MODULE DISABLE 4 CONTROL REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — U-0 bit 15 bit 8 U-0 U-0 U-0 U-0 R/W-0 U-0 U-0 U-0 — — — — REFOMD — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-4 Unimplemented: Read as ‘0’ bit 3 REFOMD: Reference Clock Module Disable bit 1 = Reference clock module is disabled 0 = Reference clock module is enabled bit 2-0 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 477 dsPIC33CH128MP508 FAMILY REGISTER 7-5: PMD6: MASTER PERIPHERAL MODULE DISABLE 6 CONTROL REGISTER HIGH U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — DMA5MD DMA4MD DMA3MD DMA2MD DMA1MD DMA0MD bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-14 Unimplemented: Read as ‘0’ bit 13 DMA5MD: DMA5 Module Disable bit 1 = DMA5 module is disabled 0 = DMA5 module is enabled bit 12 DMA4MD: DMA4 Module Disable bit 1 = DMA4 module is disabled 0 = DMA4 module is enabled bit 11 DMA3MD: DMA3 Module Disable bit 1 = DMA3 module is disabled 0 = DMA3 module is enabled bit 10 DMA2MD: DMA2 Module Disable bit 1 = DMA2 module is disabled 0 = DMA2 module is enabled bit 9 DMA1MD: DMA1 Module Disable bit 1 = DMA1 module is disabled 0 = DMA1 module is enabled bit 8 DMA0MD: DMA0 Module Disable bit 1 = DMA0 module is disabled 0 = DMA0 module is enabled bit 7-0 Unimplemented: Read as ‘0’ DS70005319D-page 478 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 7-6: PMD7: MASTER PERIPHERAL MODULE DISABLE 7 CONTROL REGISTER LOW U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — — CMP1MD bit 15 bit 8 U-0 U-0 U-0 U-0 R/W-0 U-0 U-0 U-0 — — — — PTGMD — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-9 Unimplemented: Read as ‘0’ bit 8 CMP1MD: Comparator 1 Module Disable bit 1 = Comparator 1 module is disabled 0 = Comparator 1 module is enabled bit 7-4 Unimplemented: Read as ‘0’ bit 3 PTGMD: PTG Module Disable bit 1 = PTG module is disabled 0 = PTG module is enabled bit 2-0 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 479 dsPIC33CH128MP508 FAMILY PMD8: MASTER PERIPHERAL MODULE DISABLE 8 CONTROL REGISTER(1) REGISTER 7-7: U-0 U-0 U-0 R/W-0 R/W-0 U-0 U-0 U-0 — — — SENT2MD SENT1MD — — — bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 — — CLC4MD CLC3MD CLC2MD CLC1MD BIASMD — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-13 Unimplemented: Read as ‘0’ bit 12 SENT2MD: SENT2 Module Disable bit 1 = SENT2 module is disabled 0 = SENT2 module is enabled bit 11 SENT1MD: SENT1 Module Disable bit 1 = SENT1 module is disabled 0 = SENT1 module is enabled bit 10-6 Unimplemented: Read as ‘0’ bit 5 CLC4MD: CLC4 Module Disable bit 1 = CLC4 module is disabled 0 = CLC4 module is enabled bit 4 CLC3MD: CLC3 Module Disable bit 1 = CLC3 module is disabled 0 = CLC3 module is enabled bit 3 CLC2MD: CLC2 Module Disable bit 1 = CLC2 module is disabled 0 = CLC2 module is enabled bit 2 CLC1MD: CLC1 Module Disable bit 1 = CLC1 module is disabled 0 = CLC1 module is enabled bit 1 BIASMD: Constant-Current Source Module Disable bit 1 = Constant-current source module is disabled 0 = Constant-current source module is enabled bit 0 Unimplemented: Read as ‘0’ Note 1: x = Bit is unknown This register is only available in the Master core. DS70005319D-page 480  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 7-8: PMDCON: SLAVE PMD CONTROL REGISTER U-0 U-0 U-0 U-0 R/W-0 U-0 U-0 U-0 — — — — PMDLOCK — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-12 Unimplemented: Read as ‘0’ bit 11 PMDLOCK: PMD Lock bit 1 = PMD bits can be written 0 = PMD bits are not allowed to be written bit 10-0 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 481 dsPIC33CH128MP508 FAMILY REGISTER 7-9: PMD1: SLAVE PERIPHERAL MODULE DISABLE 1 CONTROL REGISTER U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 U-0 — — — — T1MD QEIMD PWMMD — bit 15 bit 8 R/W-0 U-0 R/W-0 U-0 R/W-0 U-0 U-0 R/W-0 I2C1MD — U1MD — SPI1MD — — ADC1MD bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-12 Unimplemented: Read as ‘0’ bit 11 T1MD: Timer1 Module Disable bit 1 = Timer1 module is disabled 0 = Timer1 module is enabled bit 10 QEIMD: QEI Module Disable bit 1 = QEI module is disabled 0 = QEI module is enabled bit 9 PWMMD: PWM Module Disable bit 1 = PWM module is disabled 0 = PWM module is enabled bit 8 Unimplemented: Read as ‘0’ bit 7 I2C1MD: I2C1 Module Disable bit 1 = I2C1 module is disabled 0 = I2C1 module is enabled bit 6 Unimplemented: Read as ‘0’ bit 5 U1MD: UART1 Module Disable bit 1 = UART1 module is disabled 0 = UART1 module is enabled bit 4 Unimplemented: Read as ‘0’ bit 3 SPI1MD: SPI1 Module Disable bit 1 = SPI1 module is disabled 0 = SPI1 module is enabled bit 2-1 Unimplemented: Read as ‘0’ bit 0 ADC1MD: ADC Module Disable bit 1 = ADC module is disabled 0 = ADC module is enabled DS70005319D-page 482 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 7-10: PMD2: SLAVE PERIPHERAL MODULE DISABLE 2 CONTROL REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — — CCP4MD CCP3MD CCP2MD CCP1MD bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-4 Unimplemented: Read as ‘0’ bit 3 CCP4MD: SCCP4 Module Disable bit 1 = SCCP4 module is disabled 0 = SCCP4 module is enabled bit 2 CCP3MD: SCCP3 Module Disable bit 1 = SCCP3 module is disabled 0 = SCCP3 module is enabled bit 1 CCP2MD: SCCP2 Module Disable bit 1 = SCCP2 module is disabled 0 = SCCP2 module is enabled bit 0 CCP1MD: SCCP1 Module Disable bit 1 = SCCP1 module is disabled 0 = SCCP1 module is enabled  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 483 dsPIC33CH128MP508 FAMILY REGISTER 7-11: PMD4: SLAVE PERIPHERAL MODULE DISABLE 4 CONTROL REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — U-0 bit 15 bit 8 U-0 U-0 U-0 U-0 R/W-0 U-0 U-0 U-0 — — — — REFOMD — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-4 Unimplemented: Read as ‘0’ bit 3 REFOMD: Reference Clock Module Disable bit 1 = Reference clock module is disabled 0 = Reference clock module is enabled bit 2-0 Unimplemented: Read as ‘0’ DS70005319D-page 484 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 7-12: PMD6: SLAVE PERIPHERAL MODULE DISABLE 6 CONTROL REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 — — — — — — DMA1MD DMA0MD bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-10 Unimplemented: Read as ‘0’ bit 9 DMA1MD: DMA1 Module Disable bit 1 = DMA1 module is disabled 0 = DMA1 module is enabled bit 8 DMA0MD: DMA0 Module Disable bit 1 = DMA0 module is disabled 0 = DMA0 module is enabled bit 7-0 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 485 dsPIC33CH128MP508 FAMILY REGISTER 7-13: PMD7: SLAVE PERIPHERAL MODULE DISABLE 7 CONTROL REGISTER LOW U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 — — — — — CMP3MD CMP2MD CMP1MD bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 U-0 — — — — — — PGA1MD — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-11 Unimplemented: Read as ‘0’ bit 10 CMP3MD: Comparator 3 disable bit 1 = Comparator 3 module is disabled 0 = Comparator 3 module is enabled bit 9 CMP2MD: Comparator 2 disable bit 1 = Comparator 2 module is disabled 0 = Comparator 2 module is enabled bit 8 CMP1MD: Comparator 1 disable bit 1 = Comparator 1 module is disabled 0 = Comparator 1 module is enabled bit 7-2 Unimplemented: Read as ‘0’ bit 1 PGA1MD: PGA module disable bit 1 = PGA module is disabled 0 = PGA module is enabled bit 0 Unimplemented: Read as ‘0’ DS70005319D-page 486 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 7-14: PMD8: SLAVE PERIPHERAL MODULE DISABLE 8 CONTROL REGISTER U-0 R/W-0 U-0 U-0 U-0 R/W-0 U-0 U-0 — PGA3MD — — — PGA2MD — — bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 — — CLC4MD CLC3MD CLC2MD CLC1MD — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 Unimplemented: Read as ‘0’ bit 14 PGA3MD: PGA3 Module Disable bit 1 = PGA3 module is disabled 0 = PGA3 module is enabled bit 13-11 Unimplemented: Read as ‘0’ bit 10 PGA2MD: PGA2 Module Disable bit 1 = PGA2 module is disabled 0 = PGA2 module is enabled bit 9-6 Unimplemented: Read as ‘0’ bit 5 CLC4MD: CLC4 Module Disable bit 1 = CLC4 module is disabled 0 = CLC4 module is enabled bit 4 CLC3MD: CLC3 Module Disable bit 1 = CLC3 module is disabled 0 = CLC3 module is enabled bit 3 CLC2MD: CLC2 Module Disable bit 1 = CLC2 module is disabled 0 = CLC2 module is enabled bit 2 CLC1MD: CLC1 Module Disable bit 1 = CLC1 module is disabled 0 = CLC1 module is enabled bit 1-0 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 487 Register MASTER PMD REGISTERS Bit 15 Bit14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 PMD1 — — — — T1MD QEIMD PWMMD PMD2 — — — — — — — PMD3 — — — — — — PMD4 — — — — — — PMD6 — — PMD7 — — — PMD8 — — — TABLE 7-2: DMA5MD DMA4MD DMA3MD — — SENT2MD SENT1MD Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 — I2C1MD U2MD U1MD SPI2MD SPI1MD — C1MD ADC1MD — CCP8MD CCP7MD CCP6MD CCP5MD CCP4MD CCP3MD CCP2MD CCP1MD — — CRCMD — — — — — I2C2MD — — — — — — — REFOMD — — — DMA2MD DMA1MD DMA0MD — — — — — — — — — — CMP1MD — — — — PTGMD — — — — — — — — Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 CLC4MD CLC3MD CLC2MD CLC1MD BIASMD — SLAVE PMD REGISTERS Register Bit 15 Bit14 Bit 13 Bit 12 Bit 11 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 PMDCON — — — — PMDLOCK — — — — — — — — — — — PMD1 — — — — T1MD QEIMD PWMMD — I2C1MD — U1MD — SPI1MD — — ADC1MD PMD2 — — — — — — — — — — — — CCP4MD CCP3MD CCP2MD CCP1MD — — PMD4 — — — — — — PMD6 — — — — — — — — — — REFOMD — — — DMA1MD DMA0MD — — — — — — — PMD7 — — — — — — CMP3MD CMP2MD CMP1MD — — — — — — PGA1MD PMD8 — PGA3MD — — — — PGA2MD — — — — — — CLC4MD CLC3MD CLC2MD CLC1MD dsPIC33CH128MP508 FAMILY DS70005319D-page 488 TABLE 7-1:  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 8.0 DIRECT MEMORY ACCESS (DMA) CONTROLLER Note 1: This data sheet summarizes the features of this group of dsPIC33 devices. It is not intended to be a comprehensive reference source. For more information, refer to “Direct Memory Access Controller (DMA)” (www.microchip.com/DS30009742) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). 2: The DMA is identical for both Master core and Slave core. The x is common for both Master and Slave (where the x represents the number of the specific module being addressed). 3: All associated register names are the same on the Master core and the Slave core. The Slave code will be developed in a separate project in MPLAB® X IDE with the device selection, dsPIC33CH128MP508S1, where S1 indicates the Slave device. Table 8-1 shows an overview of the DMA module. TABLE 8-1: DMA MODULE OVERVIEW Number of DMA Modules Identical (Modules) Master Core 6 Yes Slave Core 2 Yes The Direct Memory Access (DMA) Controller is designed to service high data throughput peripherals operating on the SFR bus, allowing them to access data memory directly and alleviating the need for CPU-intensive management. By allowing these data-intensive peripherals to share their own data path, the main data bus is also deloaded, resulting in additional power savings.  2017-2019 Microchip Technology Inc. The DMA Controller functions both as a peripheral and a direct extension of the CPU. It is located on the microcontroller data bus, between the CPU and DMA-enabled peripherals, with direct access to SRAM. This partitions the SFR bus into two buses, allowing the DMA Controller access to the DMA-capable peripherals located on the new DMA SFR bus. The controller serves as a Master device on the DMA SFR bus, controlling data flow from DMA-capable peripherals. The controller also monitors CPU instruction processing directly, allowing it to be aware of when the CPU requires access to peripherals on the DMA bus and automatically relinquishing control to the CPU as needed. This increases the effective bandwidth for handling data without DMA operations, causing a processor Stall. This makes the controller essentially transparent to the user. The DMA Controller has these features: • A Total of Eight (Six Master, Two Slave), Independently Programmable Channels • Concurrent Operation with the CPU (no DMA caused Wait states) • DMA Bus Arbitration • Five Programmable Address modes • Four Programmable Transfer modes • Four Flexible Internal Data Transfer modes • Byte or Word Support for Data Transfer • 16-Bit Source and Destination Address Register for each Channel, Dynamically Updated and Reloadable • 16-Bit Transaction Count Register, Dynamically Updated and Reloadable • Upper and Lower Address Limit Registers • Counter Half-Full Level Interrupt • Software Triggered Transfer • Null Write mode for Symmetric Buffer Operations A simplified block diagram of the DMA Controller is shown if Figure 8-1. DS70005319D-page 489 dsPIC33CH128MP508 FAMILY FIGURE 8-1: DMA FUNCTIONAL BLOCK DIAGRAM CPU Execution Monitoring To DMA-Enabled Peripherals To I/O Ports and Peripherals Control Logic DMACON DMAH DMAL DMABUF Data Bus Data RAM DS70005319D-page 490 DMACH0 DMAINT0 DMASRC0 DMADST0 DMACNT0 DMACH1 DMAINT1 DMASRC1 DMADST1 DMACNT1 DMACH4 DMAINT4 DMASRC4 DMADST4 DMACNT4 DMACH5 DMAINT5 DMASRC5 DMADST5 DMACNT5 Channel 0 Channel 1 Channel 4 Channel 5 Data RAM Address Generation  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 8.1 Summary of DMA Operations The DMA Controller is capable of moving data between addresses according to a number of different parameters. Each of these parameters can be independently configured for any transaction. In addition, any or all of the DMA channels can independently perform a different transaction at the same time. Transactions are classified by these parameters: • • • • Source and destination (SFRs and data RAM) Data size (byte or word) Trigger source Transfer mode (One-Shot, Repeated or Continuous) • Addressing modes (Fixed Address or Address Blocks with or without Address Increment/Decrement) In addition, the DMA Controller provides channel priority arbitration for all channels. 8.1.1 SOURCE AND DESTINATION Using the DMA Controller, data may be moved between any two addresses in the Data Space. The SFR space (0000h to 0FFFh) or the data RAM space (Master is 1000h to 4FFFh and Slave is 1000 to 1FFFh) can serve as either the source or the destination. Data can be moved between these areas in either direction or between addresses in either area. The four different combinations are shown in Figure 8-2. If it is necessary to protect areas of data RAM, the DMA Controller allows the user to set upper and lower address boundaries for operations in the Data Space above the SFR space. The boundaries are set by the DMAH and DMAL Limit registers. If a DMA channel attempts an operation outside of the address boundaries, the transaction is terminated and an interrupt is generated. 8.1.2 DATA SIZE The DMA Controller can handle both 8-bit and 16-bit transactions. Size is user-selectable using the SIZE bit (DMACHn[1]). By default, each channel is configured for word-size transactions. When byte-size transactions are chosen, the LSB of the source and/or destination address determines if the data represent the upper or lower byte of the data RAM location. 8.1.3 TRIGGER SOURCE The DMA Controller can use 82 of the device’s interrupt sources to initiate a transaction. The DMA trigger sources occur in reverse order from their natural interrupt priority and are shown in Table 8-2.  2017-2019 Microchip Technology Inc. Since the source and destination addresses for any transaction can be programmed independently of the trigger source, the DMA Controller can use any trigger to perform an operation on any peripheral. This also allows DMA channels to be cascaded to perform more complex transfer operations. 8.1.4 TRANSFER MODE The DMA Controller supports four types of data transfers, based on the volume of data to be moved for each trigger. • One-Shot: A single transaction occurs for each trigger. • Continuous: A series of back-to-back transactions occur for each trigger; the number of transactions is determined by the DMACNTn transaction counter. • Repeated One-Shot: A single transaction is performed repeatedly, once per trigger, until the DMA channel is disabled. • Repeated Continuous: A series of transactions are performed repeatedly, one cycle per trigger, until the DMA channel is disabled. All transfer modes allow the option to have the source and destination addresses, and counter value, automatically reloaded after the completion of a transaction. 8.1.5 ADDRESSING MODES The DMA Controller also supports transfers between single addresses or address ranges. The four basic options are: • Fixed-to-Fixed: Between two constant addresses • Fixed-to-Block: From a constant source address to a range of destination addresses • Block-to-Fixed: From a range of source addresses to a single, constant destination address • Block-to-Block: From a range of source addresses to a range of destination addresses The option to select auto-increment or auto-decrement of source and/or destination addresses is available for Block Addressing modes. In addition to the four basic modes, the DMA Controller also supports Peripheral Indirect Addressing (PIA) mode, where the source or destination address is generated jointly by the DMA Controller and a PIA-capable peripheral. When enabled, the DMA channel provides a base source and/or destination address, while the peripheral provides a fixed range offset address. DS70005319D-page 491 dsPIC33CH128MP508 FAMILY FIGURE 8-2: TYPES OF DMA DATA TRANSFERS Peripheral to Memory Memory to Peripheral SFR Area SFR Area DMASRCn Data RAM 0FFFh 1000h DMAL DMA RAM Area DMADSTn Data RAM DMA RAM Area 0FFFh 1000h DMAL DMADSTn DMASRCn DMAH DMAH Peripheral to Peripheral Memory to Memory SFR Area SFR Area DMASRCn DMADSTn 0FFFh 1000h Data RAM DMA RAM Area 0FFFh 1000h DMAL DMASRCn Data RAM DMADSTn DMAH Note: Relative sizes of memory areas are not shown to scale. DS70005319D-page 492  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 8.1.6 CHANNEL PRIORITY 8.3 Peripheral Module Disable Each DMA channel functions independently of the others, but also competes with the others for access to the data and DMA buses. When access collisions occur, the DMA Controller arbitrates between the channels using a user-selectable priority scheme. Two schemes are available: The channels of the DMA Controller can be individually powered down using the Peripheral Module Disable (PMD) registers. • Round Robin: When two or more channels collide, the lower numbered channel receives priority on the first collision. On subsequent collisions, the higher numbered channels each receive priority based on their channel number. • Fixed: When two or more channels collide, the lowest numbered channel always receives priority, regardless of past history; however, any channel being actively processed is not available for an immediate retrigger. If a higher priority channel is continually requesting service, it will be scheduled for service after the next lower priority channel with a pending request. The DMA Controller uses a number of registers to control its operation. The number of registers depends on the number of channels implemented for a particular device. 8.2 • DMACHn: DMA Channel n Control Register (Register 8-2) • DMAINTn: DMA Channel n Interrupt Register (Register 8-3) • DMASRCn: DMA Data Source Address Pointer for Channel n Register • DMADSTn: DMA Data Destination Source for Channel n Register • DMACNTn: DMA Transaction Counter for Channel n Register Typical Setup To set up a DMA channel for a basic data transfer: 1. Enable the DMA Controller (DMAEN = 1) and select an appropriate channel priority scheme by setting or clearing PRSSEL. 2. Program DMAH and DMAL with appropriate upper and lower address boundaries for data RAM operations. 3. Select the DMA channel to be used and disable its operation (CHEN = 0). 4. Program the appropriate source and destination addresses for the transaction into the channel’s DMASRCn and DMADSTn registers. For PIA mode addressing, use the base address value. 5. Program the DMACNTn register for the number of triggers per transfer (One-Shot or Continuous modes) or the number of words (bytes) to be transferred (Repeated modes). 6. Set or clear the SIZE bit to select the data size. 7. Program the TRMODE[1:0] bits to select the Data Transfer mode. 8. Program the SAMODE[1:0] and DAMODE[1:0] bits to select the addressing mode. 9. Enable the DMA channel by setting CHEN. 10. Enable the trigger source interrupt.  2017-2019 Microchip Technology Inc. 8.4 Registers There are always four module-level registers (one control and three buffer/address): • DMACON: DMA Engine Control Register (Register 8-1) • DMAH and DMAL: DMA High and Low Address Limit Registers • DMABUF: DMA Transfer Data Buffer Each of the DMA channels implements five registers (two control and three buffer/address): For dsPIC33CH128MP508 devices, there are a total of 34 registers. DS70005319D-page 493 dsPIC33CH128MP508 FAMILY 8.5 DMA Control Registers REGISTER 8-1: DMACON: DMA ENGINE CONTROL REGISTER R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 DMAEN — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — — PRSSEL bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 DMAEN: DMA Module Enable bit 1 = Enables module 0 = Disables module and terminates all active DMA operation(s) bit 14-1 Unimplemented: Read as ‘0’ bit 0 PRSSEL: Channel Priority Scheme Selection bit 1 = Round robin scheme 0 = Fixed priority scheme DS70005319D-page 494 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 8-2: DMACHn: DMA CHANNEL n CONTROL REGISTER U-0 U-0 — — U-0 r-0 — R/W-0 — — R/W-0 NULLW R/W-0 R/W-0 (1) RELOAD CHREQ(3) bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SAMODE1 SAMODE0 DAMODE1 DAMODE0 TRMODE1 TRMODE0 SIZE CHEN bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-13 Unimplemented: Read as ‘0’ bit 12 Reserved: Maintain as ‘0’ bit 11 Unimplemented: Read as ‘0’ bit 10 NULLW: Null Write Mode bit 1 = A dummy write is initiated to DMASRCn for every write to DMADSTn 0 = No dummy write is initiated bit 9 RELOAD: Address and Count Reload bit(1) 1 = DMASRCn, DMADSTn and DMACNTn registers are reloaded to their previous values upon the start of the next operation 0 = DMASRCn, DMADSTn and DMACNTn are not reloaded on the start of the next operation(2) bit 8 CHREQ: DMA Channel Software Request bit(3) 1 = A DMA request is initiated by software; automatically cleared upon completion of a DMA transfer 0 = No DMA request is pending bit 7-6 SAMODE[1:0]: Source Address Mode Selection bits 11 = DMASRCn is used in Peripheral Indirect Addressing and remains unchanged 10 = DMASRCn is decremented based on the SIZE bit after a transfer completion 01 = DMASRCn is incremented based on the SIZE bit after a transfer completion 00 = DMASRCn remains unchanged after a transfer completion bit 5-4 DAMODE[1:0]: Destination Address Mode Selection bits 11 = DMADSTn is used in Peripheral Indirect Addressing and remains unchanged 10 = DMADSTn is decremented based on the SIZE bit after a transfer completion 01 = DMADSTn is incremented based on the SIZE bit after a transfer completion 00 = DMADSTn remains unchanged after a transfer completion bit 3-2 TRMODE[1:0]: Transfer Mode Selection bits 11 = Repeated Continuous 10 = Continuous 01 = Repeated One-Shot 00 = One-Shot bit 1 SIZE: Data Size Selection bit 1 = Byte (8-bit) 0 = Word (16-bit) bit 0 CHEN: DMA Channel Enable bit 1 = The corresponding channel is enabled 0 = The corresponding channel is disabled Note 1: 2: 3: Only the original DMACNTn is required to be stored to recover the original DMASRCn and DMADSTn values. DMACNTn will always be reloaded in Repeated mode transfers, regardless of the state of the RELOAD bit. The number of transfers executed while CHREQ is set depends on the configuration of TRMODE[1:0].  2017-2019 Microchip Technology Inc. DS70005319D-page 495 dsPIC33CH128MP508 FAMILY REGISTER 8-3: DMAINTn: DMA CHANNEL n INTERRUPT REGISTER R-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DBUFWF(1) CHSEL6 CHSEL5 CHSEL4 CHSEL3 CHSEL2 CHSEL1 CHSEL0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 R/W-0 HIGHIF(1,2) LOWIF(1,2) DONEIF(1) HALFIF(1) OVRUNIF(1) — — HALFEN bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 DBUFWF: DMA Buffered Data Write Flag bit(1) 1 = The content of the DMA buffer has not been written to the location specified in DMADSTn or DMASRCn in Null Write mode 0 = The content of the DMA buffer has been written to the location specified in DMADSTn or DMASRCn in Null Write mode bit 14-8 CHSEL[6:0]: DMA Channel Trigger Selection bits See Table 8-2 for a complete list. bit 7 HIGHIF: DMA High Address Limit Interrupt Flag bit(1,2) 1 = The DMA channel has attempted to access an address higher than DMAH or the upper limit of the data RAM space 0 = The DMA channel has not invoked the high address limit interrupt bit 6 LOWIF: DMA Low Address Limit Interrupt Flag bit(1,2) 1 = The DMA channel has attempted to access the DMA SFR address lower than DMAL, but above the SFR range (07FFh) 0 = The DMA channel has not invoked the low address limit interrupt bit 5 DONEIF: DMA Complete Operation Interrupt Flag bit(1) If CHEN = 1: 1 = The previous DMA session has ended with completion 0 = The current DMA session has not yet completed If CHEN = 0: 1 = The previous DMA session has ended with completion 0 = The previous DMA session has ended without completion bit 4 HALFIF: DMA 50% Watermark Level Interrupt Flag bit(1) 1 = DMACNTn has reached the halfway point to 0000h 0 = DMACNTn has not reached the halfway point bit 3 OVRUNIF: DMA Channel Overrun Flag bit(1) 1 = The DMA channel is triggered while it is still completing the operation based on the previous trigger 0 = The overrun condition has not occurred bit 2-1 Unimplemented: Read as ‘0’ bit 0 HALFEN: Halfway Completion Watermark bit 1 = Interrupts are invoked when DMACNTn has reached its halfway point and at completion 0 = An interrupt is invoked only at the completion of the transfer Note 1: 2: Setting these flags in software does not generate an interrupt. Testing for address limit violations (DMASRCn or DMADSTn is either greater than DMAH or less than DMAL) is NOT done before the actual access. DS70005319D-page 496  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 8-2: DMA CHANNEL TRIGGER SOURCES (MASTER) CHSEL[6:0] Trigger (Interrupt) CHSEL[6:0] Trigger (Interrupt) 00h 01h INT0 – External Interrupt 0 23h (Reserved, do not use) 45h CLC2 Interrupt SCCP1 IC/OC 24h PWM Event C 46h SPI1 – Fault Interrupt 02h SPI1 Receiver 25h SENT1 TX/RX 47h SPI2 – Fault Interrupt 03h SPI1 Transmitter 26h SENT2 TX/RX 48h (Reserved, do not use) 04h UART1 Receiver 27h ADC1 Group Convert Done 49h (Reserved, do not use) 05h UART1 Transmitter 28h ADC Done AN0 4Ah MSI Slave Initiated Slave IRQ MSI Protocol A CHSEL[6:0] Trigger (Interrupt) 06h ECC Single Bit Error 29h ADC Done AN1 4Bh 07h NVM Write Complete 2Ah ADC Done AN2 4Ch MSI Protocol B 08h INT1 – External Interrupt 1 2Bh ADC Done AN3 4Dh MSI Protocol C 09h SI2C1 – I2C1 Slave Event 2Ch ADC Done AN4 4Eh MSI Protocol D 0Ah MI2C1 – I2C1 Master Event 2Dh ADC Done AN5 4Fh MSI Protocol E 0Bh INT2 – External Interrupt 2 2Eh ADC Done AN6 50h MSI Protocol F 0Ch SCCP2 IC/OC 2Fh ADC Done AN7 51h MSI Protocol G 0Dh INT3 – External Interrupt 3 30h ADC Done AN8 52h MSI Protocol H 0Eh UART2 Receiver 31h ADC Done AN9 53h MSI Master Read FIFO Data Ready IRQ 0Fh UART2 Transmitter 32h ADC Done AN10 54h MSI Master Write FIFO Empty IRQ 10h SPI2 Receiver 33h ADC Done AN11 55h MSI Fault (Over/Underflow) 11h SPI2 Transmitter 34h ADC Done AN12 56h MSI Master Reset IRQ 12h SCCP3 IC/OC 35h ADC Done AN13 57h PWM Event D 13h SI2C2 – I2C2 Slave Event 36h ADC Done AN14 58h PWM Event E 14h MI2C2 – I2C1 Master Event 37h ADC Done AN15 59h PWM Event F 15h SCCP4 IC/OC 38h ADC Done AN16 5Ah Slave ICD Breakpoint Interrupt 16h SCCP5 IC/OC 39h ADC Done AN17 5Bh (Reserved, do not use) 17h SCCP6 IC/OC 3Ah (Reserved, do not use) 5Ch SCCP7 Interrupt 18h CRC Generator Interrupt 3Bh (Reserved, do not use) 5Dh SCCP8 Interrupt 19h PWM Event A 3Ch (Reserved, do not use) 5Eh Slave Clock Fail Interrupt 1Bh PWM Event B 3Dh (Reserved, do not use) 5Fh ADC FIFO Ready Interrupt 1Ch PWM Generator 1 3Eh (Reserved, do not use) 60h CLC3 Positive Edge Interrupt 1Dh PWM Generator 2 3Fh (Reserved, do not use) 61h CLC4 Positive Edge Interrupt 1Eh PWM Generator 3 40h AD1FLTR1 – Oversample Filter 1 62h 1Fh PWM Generator 4 41h AD1FLTR2 – Oversample Filter 2 ... 20h (Reserved, do not use) 42h AD1FLTR3 – Oversample Filter 3 7Fh 21h (Reserved, do not use) 43h AD1FLTR4 – Oversample Filter 4 22h (Reserved, do not use) 44h CLC1 Interrupt  2017-2019 Microchip Technology Inc. (Reserved, do not use) DS70005319D-page 497 dsPIC33CH128MP508 FAMILY TABLE 8-3: CHSEL[6:0] DMA CHANNEL TRIGGER SOURCES (SLAVE) Trigger (Interrupt) CHSEL[6:0] Trigger (Interrupt) CHSEL[6:0] Trigger (Interrupt) 0000000 00h INT0 – External Interrupt 0 0100010 22h PWM Generator 7 1000100 44h CLC1 Interrupt 0000001 01h SCCP1 IC/OC 0100011 23h PWM Generator 8 1000101 45h CLC2 Interrupt 0000010 02h SPI1 Receiver 0100100 24h PWM Event C 1000110 46h SPI1 – Fault Interrupt 0000011 03h SPI1 Transmitter 0100101 25h (Reserved, do not use) 1000111 47h (Reserved, do not use) 0000100 04h UART1 Receiver 0100110 26h (Reserved, do not use) 1001000 48h (Reserved, do not use) 0000101 05h UART1 Transmitter 0100111 27h ADC1 Group Convert Done 1001001 49h (Reserved, do not use) 0000110 06h ECC Single Bit Error 0101000 28h ADC Done AN0 1001010 4Ah MSI Master Initiated Slave IRQ 0000111 07h NVM Write Complete 0101001 29h ADC Done AN1 1001011 4Bh MSI Protocol A 0001000 08h INT1 – External Interrupt 1 0101010 2Ah ADC Done AN2 1001100 4Ch MSI Protocol B 0001001 09h SI2C1 – I2C1 Slave Event 0101011 2Bh ADC Done AN3 1001101 4Dh MSI Protocol C 0001010 0Ah MI2C1 – I2C1 Master Event 0101100 2Ch ADC Done AN4 1001110 4Eh MSI Protocol D 0001010 0Bh INT2 – External Interrupt 2 0101101 2Dh ADC Done AN5 1001111 4Fh MSI Protocol E 0001100 0Ch SCCP2 IC/OC 0101110 2Eh ADC Done AN6 1010000 50h MSI Protocol F 0001101 0Dh INT3 – External Interrupt 3 0101111 2Fh ADC Done AN7 1010001 51h MSI Protocol G 0001110 0Eh (Reserved, do not use) 0110000 30h ADC Done AN8 1010010 52h MSI Protocol H 0001111 0Fh (Reserved, do not use) 0110001 31h ADC Done AN9 1010011 53h MSI Slave Read FIFO Data Ready IRQ 0010000 10h (Reserved, do not use) 0110010 32h ADC Done AN10 1010100 54h MSI Slave Write FIFO Empty IRQ 0010001 11h (Reserved, do not use) 0110011 33h ADC Done AN11 1010101 55h MSI FIFO Fault (Over/Underflow) 0010010 12h SCCP3 IC/OC 0110100 34h ADC Done AN12 1010110 56h MSI Master Reset IRQ 0010011 13h (Reserved, do not use) 0110101 35h ADC Done AN13 1010111 57h PWM Event D 0010100 14h (Reserved, do not use) 0110110 36h ADC Done AN14 1011000 58h PWM Event E 0010101 15h SCCP4 IC/OC 0110111 37h ADC Done AN15 1011001 59h PWM Event F 0010110 16h (Reserved, do not use) 0111000 38h ADC Done AN16 1011010 5Ah Master ICD Breakpoint Interrupt 0010111 17h (Reserved, do not use) 0111001 39h ADC Done AN17 1011011 5Bh (Reserved, do not use) 0011000 18h (Reserved, do not use) 0111010 3Ah (Reserved, do not use) 1011100 5Ch (Reserved, do not use) 0011001 19h PWM Event A 0111010 3Bh ADC Done AN19 1011101 5Dh (Reserved, do not use) 0011010 1Ah (Reserved, do not use) 0111100 3Ch (Reserved, do not use) 1011110 5Eh Master Clock Fail Interrupt 0011011 1Bh PWM Event B 0111101 3Dh (Reserved, do not use) 1011111 5Fh ADC FIFO Ready Interrupt 0011100 1Ch PWM Generator 1 0111110 3Eh (Reserved, do not use) 1100000 60h CLC3 Positive Edge Interrupt 0011101 1Dh PWM Generator 2 0111111 3Fh (Reserved, do not use) 1100001 61h CLC4 Positive Edge Interrupt 0011110 1Eh PWM Generator 3 1000000 40h AD1FLTR1 – Oversample Filter 1 1100001 62h 0011111 1Fh PWM Generator 4 1000001 41h AD1FLTR2 – Oversample Filter 2 0100000 20h PWM Generator 5 1000010 42h AD1FLTR3 – Oversample Filter 3 1111111 7Fh 0100001 21h PWM Generator 6 1000011 43h AD1FLTR4 – Oversample Filter 4 DS70005319D-page 498 ... ... (Reserved, do not use) (Reserved, do not use)  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 9.0 HIGH-RESOLUTION PWM (HSPWM) WITH FINE EDGE PLACEMENT Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “High-Resolution PWM with Fine Edge Placement” (www.microchip.com/DS70005320) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). 2: The PWM is identical for both Master core and Slave core. The x is common for both Master core and Slave core (where the x represents the number of the specific module being addressed). The number of HSPWM modules available on the Master core and Slave core is different and they are located in different SFR locations. 3: All associated register names are the same on the Master core and the Slave core. The Slave code will be developed in a separate project in MPLAB® X IDE with the device selection, dsPIC33CH128MP508S1, where the S1 indicates the Slave device. The Master is PWM1 to PWM4 and the Slave is PWM1 to PWM8. 9.1 Features • Up to Eight Independent PWM Generators for Slave Core, each with Dual Outputs • Up to Four Independent PWM Generators for Master Core, each with Dual Outputs • Operating modes: - Independent Edge mode - Variable Phase PWM mode - Center-Aligned mode - Double Update Center-Aligned mode - Dual Edge Center-Aligned mode - Dual PWM mode • Output modes: - Complementary - Independent - Push-Pull • Dead-Time Generator • Leading-Edge Blanking (LEB) • Output Override for Fault Handling • Flexible Period/Duty Cycle Updating Options • Programmable Control Inputs (PCI) • Advanced Triggering Options • Six Combinatorial Logic Outputs • Six PWM Event Outputs Table 9-1 shows an overview of the PWM module. TABLE 9-1: PWM MODULE OVERVIEW Number of PWM Modules Identical (Modules) Master Core 4 Yes Slave Core 8 Yes The High-Speed PWM (HSPWM) module is a Pulse-Width Modulated (PWM) module to support both motor control and power supply applications. This flexible module provides features to support many types of Motor Control (MC) and Power Control (PC) applications, including: • • • • • • • AC-to-DC Converters DC-to-DC Converters AC and DC Motors: BLDC, PMSM, ACIM, SRM, etc. Inverters Battery Chargers Digital Lighting Power Factor Correction (PFC)  2017-2019 Microchip Technology Inc. DS70005319D-page 499 dsPIC33CH128MP508 FAMILY 9.2 Architecture Overview The PWM module consists of a common set of controls and features, and multiple instantiations of PWM Generators (PGs). Each PWM Generator can be independently configured or multiple PWM Generators can FIGURE 9-1: be used to achieve complex multiphase systems. PWM Generators can also be used to implement sophisticated triggering, protection and logic functions. A high-level block diagram is shown in Figure 9-1. PWM HIGH-LEVEL BLOCK DIAGRAM PWM1H Common PWM Controls and Data PG1 PWM1L PWM2H PG2 PWM2L PWMxH PGx PWMxL 9.3 PWM4H/L Output on Peripheral Pin Select All devices support the capability to output PWM4H and PWM4L signals via Peripheral Pin Select (PPS) onto any RPn pin. This feature is intended for lower pin count devices that do not have PWM4H/L on dedicated pins. If PWM4H/L PPS output functions are used on devices that also have fixed PWM4H/L pins, the output signal will be present on both dedicated and RPn pins. The output port enable bits, PENH and PENL (PGxIOCONH[3:2]), control both dedicated and PPS pins together; it is not possible to disable the dedicated pins and use only PPS. DS70005319D-page 500 Given the natural priority of the RPn functions above that of the PWM, it is possible to use the PPS output functions on the dedicated PWM4H/L pins while the PWM4 signals are routed to other pins via PPS. Any of the peripheral outputs listed in Table 3-32 and Table 4-28, with the exception of ‘Default Port’, can be used. Input functions, including the ports and peripherals listed in Table 3-33 and Table 4-31, cannot be used through the RPn function on dedicated PWM4H/L pins when PWM4 is active.  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 9.4 PWM Control Registers An ‘x’ in the register name denotes an instance of a PWM Generator. There are two categories of Special Function Registers (SFRs) used to control the operation of the PWM module: A ‘y’ in the register name denotes an instance of the common function. • Common, shared by all PWM Generators • PWM Generator-specific REGISTER 9-1: PCLKCON: PWM CLOCK CONTROL REGISTER R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0 R/W-0 HRRDY HRERR — — — — — LOCK(1) bit 15 bit 8 U-0 U-0 — — R/W-0 DIVSEL1 R/W-0 U-0 DIVSEL0 U-0 R/W-0 R/W-0 — MCLKSEL1(2) MCLKSEL0(2) — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 HRRDY: High-Resolution Ready bit 1 = The high-resolution circuitry is ready 0 = The high-resolution circuitry is not ready bit 14 HRERR: High-Resolution Error bit 1 = An error has occurred; PWM signals will have limited resolution 0 = No error has occurred; PWM signals will have full resolution when HRRDY = 1 bit 13-9 Unimplemented: Read as ‘0’ bit 8 LOCK: Lock bit(1) 1 = Write-protected registers and bits are locked 0 = Write-protected registers and bits are unlocked bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 DIVSEL[1:0]: PWM Clock Divider Selection bits 11 = Divide ratio is 1:16 10 = Divide ratio is 1:8 01 = Divide ratio is 1:4 00 = Divide ratio is 1:2 bit 3-2 Unimplemented: Read as ‘0’ bit 1-0 MCLKSEL[1:0]: PWM Master Clock Selection bits(2) 11 = AFPLLO – Auxiliary PLL post-divider output 10 = FPLLO – Primary PLL post-divider output 01 = AFVCO/2 – Auxiliary VCO/2 00 = FOSC Note 1: 2: A device-specific unlock sequence must be performed before this bit can be cleared. Changing the MCLKSEL[1:0] bits while ON (PGxCONL[15]) = 1 is not recommended.  2017-2019 Microchip Technology Inc. DS70005319D-page 501 dsPIC33CH128MP508 FAMILY REGISTER 9-2: R/W-0 FSCL: FREQUENCY SCALE REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FSCL[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FSCL[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown FSCL[15:0]: Frequency Scale Register bits The value in this register is added to the frequency scaling accumulator at each pwm_clk. When the accumulated value exceeds the value of FSMINPER, a clock pulse is produced. REGISTER 9-3: R/W-0 FSMINPER: FREQUENCY SCALING MINIMUM PERIOD REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FSMINPER[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FSMINPER[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown FSMINPER[15:0]: Frequency Scaling Minimum Period Register bits This register holds the minimum clock period (maximum clock frequency) that can be produced by the frequency scaling circuit. DS70005319D-page 502  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 9-4: R/W-0 MPHASE: MASTER PHASE REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 MPHASE[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 MPHASE[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown MPHASE[15:0]: Master Phase Register bits REGISTER 9-5: R/W-0 MDC: MASTER DUTY CYCLE REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 MDC[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 MDC[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown MDC[15:0]: Master Duty Cycle Register bits  2017-2019 Microchip Technology Inc. DS70005319D-page 503 dsPIC33CH128MP508 FAMILY REGISTER 9-6: R/W-0 MPER: MASTER PERIOD REGISTER R/W-0 R/W-0 R/W-0 R/W-0 MPER[15:8] R/W-0 R/W-0 R/W-0 (1) bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 (1) MPER[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: x = Bit is unknown MPER[15:0]: Master Period Register bits(1) Period values less than ‘0x0010’ should not be selected. DS70005319D-page 504  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 9-7: CMBTRIGL: COMBINATIONAL TRIGGER REGISTER LOW U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CTA8EN CTA7EN CTA6EN CTA5EN CTA4EN CTA3EN CTA2EN CTA1EN bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7 CTA8EN: Enable Trigger Output from PWM Generator #8 as Source for Combinational Trigger A bit 1 = Enables specified trigger signal to be OR’d into the Combinatorial Trigger A signal 0 = Disabled bit 6 CTA7EN: Enable Trigger Output from PWM Generator #7 as Source for Combinational Trigger A bit 1 = Enables specified trigger signal to be OR’d into the Combinatorial Trigger A signal 0 = Disabled bit 5 CTA6EN: Enable Trigger Output from PWM Generator #6 as Source for Combinational Trigger A bit 1 = Enables specified trigger signal to be OR’d into the Combinatorial Trigger A signal 0 = Disabled bit 4 CTA5EN: Enable Trigger Output from PWM Generator #5 as Source for Combinational Trigger A bit 1 = Enables specified trigger signal to be OR’d into the Combinatorial Trigger A signal 0 = Disabled bit 3 CTA4EN: Enable Trigger Output from PWM Generator #4 as Source for Combinational Trigger A bit 1 = Enables specified trigger signal to be OR’d into the Combinatorial Trigger A signal 0 = Disabled bit 2 CTA3EN: Enable Trigger Output from PWM Generator #3 as Source for Combinational Trigger A bit 1 = Enables specified trigger signal to be OR’d into the Combinatorial Trigger A signal 0 = Disabled bit 1 CTA2EN: Enable Trigger Output from PWM Generator #2 as Source for Combinational Trigger A bit 1 = Enables specified trigger signal to be OR’d into the Combinatorial Trigger A signal 0 = Disabled bit 0 CTA1EN: Enable Trigger Output from PWM Generator #1 as Source for Combinational Trigger A bit 1 = Enables specified trigger signal to be OR’d into the Combinatorial Trigger A signal 0 = Disabled  2017-2019 Microchip Technology Inc. DS70005319D-page 505 dsPIC33CH128MP508 FAMILY REGISTER 9-8: CMBTRIGH: COMBINATIONAL TRIGGER REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CTB8EN CTB7EN CTB6EN CTB5EN CTB4EN CTB3EN CTB2EN CTB1EN bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7 CTB8EN: Enable Trigger Output from PWM Generator #8 as Source for Combinational Trigger B bit 1 = Enables specified trigger signal to be OR’d into the Combinatorial Trigger B signal 0 = Disabled bit 6 CTB7EN: Enable Trigger Output from PWM Generator #7 as Source for Combinational Trigger B bit 1 = Enables specified trigger signal to be OR’d into the Combinatorial Trigger B signal 0 = Disabled bit 5 CTB6EN: Enable Trigger Output from PWM Generator #6 as Source for Combinational Trigger B bit 1 = Enables specified trigger signal to be OR’d into the Combinatorial Trigger B signal 0 = Disabled bit 4 CTB5EN: Enable Trigger Output from PWM Generator #5 as Source for Combinational Trigger B bit 1 = Enables specified trigger signal to be OR’d into the Combinatorial Trigger B signal 0 = Disabled bit 3 CTB4EN: Enable Trigger Output from PWM Generator #4 as Source for Combinational Trigger B bit 1 = Enables specified trigger signal to be OR’d into the Combinatorial Trigger B signal 0 = Disabled bit 2 CTB3EN: Enable Trigger Output from PWM Generator #3 as Source for Combinational Trigger B bit 1 = Enables specified trigger signal to be OR’d into the Combinatorial Trigger B signal 0 = Disabled bit 1 CTB2EN: Enable Trigger Output from PWM Generator #2 as Source for Combinational Trigger B bit 1 = Enables specified trigger signal to be OR’d into the Combinatorial Trigger B signal 0 = Disabled bit 0 CTB1EN: Enable Trigger Output from PWM Generator #1 as Source for Combinational Trigger B bit 1 = Enables specified trigger signal to be OR’d into the Combinatorial Trigger B signal 0 = Disabled DS70005319D-page 506  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 9-9: R/W-0 LOGCONy: COMBINATORIAL PWM LOGIC CONTROL REGISTER y(2) R/W-0 PWMS1y3(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PWMS1y2(1) PWMS1y1(1) PWMS1y0(1) PWMS2y3(1) PWMS2y2(1) PWMS2y1(1) PWMS2y0(1) bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 S1yPOL S2yPOL PWMLFy1 PWMLFy0 — PWMLFyD2 R/W-0 R/W-0 PWMLFyD1 PWMLFyD0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-12 PWMS1y[3:0]: Combinatorial PWM Logic Source #1 Selection bits(1) 1111 = PWM8L 1110 = PWM8H 1101 = PWM7L 1100 = PWM7H 1011 = PWM6L 1010 = PWM6H 1001 = PWM5L 1000 = PWM5H 0111 = PWM4L 0110 = PWM4H 0101 = PWM3L 0100 = PWM3H 0011 = PWM2L 0010 = PWM2H 0001 = PWM1L 0000 = PWM1H bit 11-8 PWMS2y[3:0]: Combinatorial PWM Logic Source #2 Selection bits(1) 1111 = PWM8L 1110 = PWM8H 1101 = PWM7L 1100 = PWM7H 1011 = PWM6L 1010 = PWM6H 1001 = PWM5L 1000 = PWM5H 0111 = PWM4L 0110 = PWM4H 0101 = PWM3L 0100 = PWM3H 0011 = PWM2L 0010 = PWM2H 0001 = PWM1L 0000 = PWM1H Note 1: 2: x = Bit is unknown Logic function input will be connected to ‘0’ if the PWM channel is not present. Instances of y = A, C, E of LOGCONy assign logic function output to the PWMxH pin. Instances of y = B, D, F of LOGCONy assign logic function to the PWMxL pin.  2017-2019 Microchip Technology Inc. DS70005319D-page 507 dsPIC33CH128MP508 FAMILY REGISTER 9-9: LOGCONy: COMBINATORIAL PWM LOGIC CONTROL REGISTER y(2) (CONTINUED) bit 7 S1yPOL: Combinatorial PWM Logic Source #1 Polarity bit 1 = Input is inverted 0 = Input is positive logic bit 6 S2yPOL: Combinatorial PWM Logic Source #2 Polarity bit 1 = Input is inverted 0 = Input is positive logic bit 5-4 PWMLFy[1:0]: Combinatorial PWM Logic Function Selection bits 11 = Reserved 10 = PWMS1 ^ PWMS2 (XOR) 01 = PWMS1 & PWMS2 (AND) 00 = PWMS1 | PWMS2 (OR) bit 3 Unimplemented: Read as ‘0’ bit 2-0 PWMLFyD[2:0]: Combinatorial PWM Logic Destination Selection bits 111 = Logic function is assigned to the PWM8H or PWM8L pin 110 = Logic function is assigned to the PWM7H or PWM7L pin 101 = Logic function is assigned to the PWM6H or PWM6L pin 100 = Logic function is assigned to the PWM5H or PWM5Lpin 011 = Logic function is assigned to the PWM4H or PWM4Lpin 010 = Logic function is assigned to the PWM3H or PWM3Lpin 001 = Logic function is assigned to the PWM2H or PWM2Lpin 000 = No assignment, combinatorial PWM logic function is disabled Note 1: 2: Logic function input will be connected to ‘0’ if the PWM channel is not present. Instances of y = A, C, E of LOGCONy assign logic function output to the PWMxH pin. Instances of y = B, D, F of LOGCONy assign logic function to the PWMxL pin. DS70005319D-page 508  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 9-10: PWMEVTy: PWM EVENT OUTPUT CONTROL REGISTER y(5) R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 U-0 EVTyOEN EVTyPOL EVTySTRD EVTySYNC — — — — bit 15 bit 8 R/W-0 R/W-0 EVTySEL3 EVTySEL2 R/W-0 EVTySEL1 R/W-0 EVTySEL0 U-0 — R/W-0 R/W-0 (2) EVTyPGS2 EVTyPGS1 R/W-0 (2) EVTyPGS0(2) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 EVTyOEN: PWM Event Output Enable bit 1 = Event output signal is output on PWMEy pin 0 = Event output signal is internal only bit 14 EVTyPOL: PWM Event Output Polarity bit 1 = Event output signal is active-low 0 = Event output signal is active-high bit 13 EVTySTRD: PWM Event Output Stretch Disable bit 1 = Event output signal pulse width is not stretched 0 = Event output signal is stretched to eight PWM clock cycles minimum(1) bit 12 EVTySYNC: PWM Event Output Sync bit 1 = Event output signal is synchronized to the system clock 0 = Event output is not synchronized to the system clock Event output signal pulse will be two system clocks when this bit is set and EVTySTRD = 1. bit 11-8 Unimplemented: Read as ‘0’ bit 7-4 EVTySEL[3:0]: PWM Event Selection bits 1111 = High-resolution error event signal 1110-1010 = Reserved 1001 = ADC Trigger 2 signal 1000 = ADC Trigger 1 signal 0111 = STEER signal (available in Push-Pull Output modes only)(4) 0110 = CAHALF signal (available in Center-Aligned modes only)(4) 0101 = PCI Fault active output signal 0100 = PCI current-limit active output signal 0011 = PCI feed-forward active output signal 0010 = PCI Sync active output signal 0001 = PWM Generator output signal(3) 0000 = Source is selected by the PGTRGSEL[2:0] bits bit 3 Unimplemented: Read as ‘0’ Note 1: 2: 3: 4: 5: The event signal is stretched using the peripheral clock because different PGs may be operating from different clock sources. The leading edge of the event pulse is produced in the clock domain of the PWM Generator. The trailing edge of the stretched event pulse is produced in the peripheral clock domain. No event will be produced if the selected PWM Generator is not present. This is the PWM Generator output signal prior to output mode logic and any output override logic. This signal should be the PGx_clk domain signal prior to any synchronization into the system clock domain. ‘y’ denotes a common instance (A-F).  2017-2019 Microchip Technology Inc. DS70005319D-page 509 dsPIC33CH128MP508 FAMILY REGISTER 9-10: PWMEVTy: PWM EVENT OUTPUT CONTROL REGISTER y(5) (CONTINUED) EVTyPGS[2:0]: PWM Event Source Selection bits(2) 111 = PG8 110 = PG7 101 = PG6 100 = PG5 011 = PG4 010 = PG3 001 = PG2 000 = PG1 bit 2-0 Note 1: 2: 3: 4: 5: The event signal is stretched using the peripheral clock because different PGs may be operating from different clock sources. The leading edge of the event pulse is produced in the clock domain of the PWM Generator. The trailing edge of the stretched event pulse is produced in the peripheral clock domain. No event will be produced if the selected PWM Generator is not present. This is the PWM Generator output signal prior to output mode logic and any output override logic. This signal should be the PGx_clk domain signal prior to any synchronization into the system clock domain. ‘y’ denotes a common instance (A-F). DS70005319D-page 510  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 9-11: U-0 LFSR: LINEAR FEEDBACK SHIFT REGISTER R/W-0 R/W-0 R/W-0 — R/W-0 R/W-0 R/W-0 R/W-0 LFSR[14:8] bit 15 R/W-0 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 LFSR[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 Unimplemented: Read as ‘0’ bit 14-0 LFSR[14:0]: Linear Feedback Shift Register bits A read of this register will provide a 15-bit pseudorandom value.  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 511 dsPIC33CH128MP508 FAMILY REGISTER 9-12: PGxCONL: PWM GENERATOR x CONTROL REGISTER LOW R/W-0 r-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 ON — — — — TRGCNT2 TRGCNT1 TRGCNT0 bit 15 bit 8 R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 HREN — — CLKSEL1 CLKSEL0 MODSEL2 MODSEL1 MODSEL0 bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ON: Enable bit 1 = PWM Generator is enabled 0 = PWM Generator is not enabled bit 14 Reserved: Maintain as ‘0’ bit 13-11 Unimplemented: Read as ‘0’ bit 10-8 TRGCNT[2:0]: Trigger Count Select bits 111 = PWM Generator produces eight PWM cycles after triggered 110 = PWM Generator produces seven PWM cycles after triggered 101 = PWM Generator produces six PWM cycles after triggered 100 = PWM Generator produces five PWM cycles after triggered 011 = PWM Generator produces four PWM cycles after triggered 010 = PWM Generator produces three PWM cycles after triggered 001 = PWM Generator produces two PWM cycles after triggered 000 = PWM Generator produces one PWM cycle after triggered bit 7 HREN: PWM Generator x High-Resolution Enable bit 1 = PWM Generator x operates in High-Resolution mode(2) 0 = PWM Generator x operates in standard resolution bit 6-5 Unimplemented: Read as ‘0’ bit 4-3 CLKSEL[1:0]: Clock Selection bits 11 = PWM Generator uses Master clock scaled by frequency scaling circuit(1) 10 = PWM Generator uses Master clock divided by clock divider circuit(1) 01 = PWM Generator uses Master clock selected by the MCLKSEL[1:0] (PCLKCON[1:0]) control bits 00 = No clock selected, PWM Generator is in lowest power state (default) bit 2-0 MODSEL[2:0]: Mode Selection bits 111 = Dual Edge Center-Aligned PWM mode (interrupt/register update twice per cycle) 110 = Dual Edge Center-Aligned PWM mode (interrupt/register update once per cycle) 101 = Double-Update Center-Aligned PWM mode 100 = Center-Aligned PWM mode 011 = Reserved 010 = Independent Edge PWM mode, dual output 001 = Variable Phase PWM mode 000 = Independent Edge PWM mode Note 1: 2: The PWM Generator time base operates from the frequency scaling circuit clock, effectively scaling the duty cycle and period of the PWM Generator output. Input frequency of 500 MHz must be used for High-Resolution mode. DS70005319D-page 512  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 9-13: PGxCONH: PWM GENERATOR x CONTROL REGISTER HIGH R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 MDCSEL MPERSEL MPHSEL — MSTEN UPDMOD2 UPDMOD1 UPDMOD0 bit 15 bit 8 r-0 R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 — TRGMOD — — SOCS3(1,2,3) SOCS2(1,2,3) SOCS1(1,2,3) SOCS0(1,2,3) bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 MDCSEL: Master Duty Cycle Register Select bit 1 = PWM Generator uses the MDC register instead of PGxDC 0 = PWM Generator uses the PGxDC register bit 14 MPERSEL: Master Period Register Select bit 1 = PWM Generator uses the MPER register instead of PGxPER 0 = PWM Generator uses the PGxPER register bit 13 MPHSEL: Master Phase Register Select bit 1 = PWM Generator uses the MPHASE register instead of PGxPHASE 0 = PWM Generator uses the PGxPHASE register bit 12 Unimplemented: Read as ‘0’ bit 11 MSTEN: Master Update Enable bit 1 = PWM Generator broadcasts software set/clear of the UPDATE status bit and EOC signal to other PWM Generators 0 = PWM Generator does not broadcast the UPDATE status bit state or EOC signal bit 10-8 UPDMOD[2:0]: PWM Buffer Update Mode Selection bits 011 = Slaved immediate update Data registers update immediately, or as soon as possible, when a Master update request is received. A Master update request will be transmitted if MSTEN = 1 and UPDREQ = 1 for the requesting PWM Generator. 010 = Slaved SOC update Data registers update at start of next cycle if a Master update request is received. A Master update request will be transmitted if MSTEN = 1 and UPDREQ = 1 for the requesting PWM Generator. 001 = Immediate update Data registers update immediately, or as soon as possible, if UPDREQ = 1. The UPDATE status bit will be cleared automatically after the update occurs. 000 = SOC update Data registers update at start of next PWM cycle if UPDREQ = 1. The UPDATE status bit will be cleared automatically after the update occurs. bit 7 Reserved: Maintain as ‘0’ Note 1: 2: 3: The PCI selected Sync signal is always available to be OR’d with the selected SOC signal per the SOCS[3:0] bits if the PCI Sync function is enabled. The source selected by the SOCS[3:0] bits MUST operate from the same clock source as the local PWM Generator. If not, the source must be routed through the PCI Sync logic so the trigger signal may be synchronized to the PWM Generator clock domain. PWM Generators are grouped into groups of four: PG1-PG4 and PG5-PG8, if available. Any generator within a group of four may be used to trigger another generator within the same group.  2017-2019 Microchip Technology Inc. DS70005319D-page 513 dsPIC33CH128MP508 FAMILY REGISTER 9-13: PGxCONH: PWM GENERATOR x CONTROL REGISTER HIGH (CONTINUED) bit 6 TRGMOD: PWM Generator Trigger Mode Selection bit 1 = PWM Generator operates in Retriggerable mode 0 = PWM Generator operates in Single Trigger mode bit 5-4 Unimplemented: Read as ‘0’ bit 3-0 SOCS[3:0]: Start-of-Cycle Selection bits(1,2,3) 1111 = TRIG bit or PCI Sync function only (no hardware trigger source is selected) 1110-0101 = Reserved 0100 = PWM4(8) PG1 or PG5 trigger output selected by PGTRGSEL[2:0] (PGxEVT[2:0]) 0011 = PWM3(7) PG1 or PG5 trigger output selected by PGTRGSEL[2:0] (PGxEVT[2:0]) 0010 = PWM2(6) PG1 or PG5 trigger output selected by PGTRGSEL[2:0] (PGxEVT[2:0]) 0001 = PWM1(5) PG1 or PG5 trigger output selected by PGTRGSEL[2:0] (PGxEVT[2:0]) 0000 = Local EOC – PWM Generator is self-triggered Note 1: 2: 3: The PCI selected Sync signal is always available to be OR’d with the selected SOC signal per the SOCS[3:0] bits if the PCI Sync function is enabled. The source selected by the SOCS[3:0] bits MUST operate from the same clock source as the local PWM Generator. If not, the source must be routed through the PCI Sync logic so the trigger signal may be synchronized to the PWM Generator clock domain. PWM Generators are grouped into groups of four: PG1-PG4 and PG5-PG8, if available. Any generator within a group of four may be used to trigger another generator within the same group. DS70005319D-page 514  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 9-14: PGxSTAT: PWM GENERATOR x STATUS REGISTER HS/C-0 HS/C-0 HS/C-0 HS/C-0 R-0 R-0 R-0 R-0 SEVT FLTEVT CLEVT FFEVT SACT FLTACT CLACT FFACT bit 15 bit 8 W-0 W-0 HS/R-0 R-0 W-0 R-0 R-0 R-0 TRSET TRCLR CAP(1) UPDATE UPDREQ STEER CAHALF TRIG bit 7 bit 0 Legend: C = Clearable bit HS = Hardware Settable bit R = Readable bit W = Writable bit ‘0’ = Bit is cleared -n = Value at POR ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ x = Bit is unknown bit 15 SEVT: PCI Sync Event bit 1 = A PCI Sync event has occurred (rising edge on PCI Sync output or PCI Sync output is high when module is enabled) 0 = No PCI Sync event has occurred bit 14 FLTEVT: PCI Fault Active Status bit 1 = A Fault event has occurred (rising edge on PCI Fault output or PCI Fault output is high when module is enabled) 0 = No Fault event has occurred bit 13 CLEVT: PCI Current-Limit Status bit 1 = A PCI current-limit event has occurred (rising edge on PCI current-limit output or PCI current-limit output is high when module is enabled) 0 = No PCI current-limit event has occurred bit 12 FFEVT: PCI Feed-Forward Active Status bit 1 = A PCI feed-forward event has occurred (rising edge on PCI feed-forward output or PCI feed-forward output is high when module is enabled) 0 = No PCI feed-forward event has occurred bit 11 SACT: PCI Sync Status bit 1 = PCI Sync output is active 0 = PCI Sync output is inactive bit 10 FLTACT: PCI Fault Active Status bit 1 = PCI Fault output is active 0 = PCI Fault output is inactive bit 9 CLACT: PCI Current-Limit Status bit 1 = PCI current-limit output is active 0 = PCI current-limit output is inactive bit 8 FFACT: PCI Feed-Forward Active Status bit 1 = PCI feed-forward output is active 0 = PCI feed-forward output is inactive bit 7 TRSET: PWM Generator Software Trigger Set bit User software writes a ‘1’ to this bit location to trigger a PWM Generator cycle. The bit location always reads as ‘0’. The TRIG bit will indicate ‘1’ when the PWM Generator is triggered. bit 6 TRCLR: PWM Generator Software Trigger Clear bit User software writes a ‘1’ to this bit location to stop a PWM Generator cycle. The bit location always reads as ‘0’. The TRIG bit will indicate ‘0’ when the PWM Generator is not triggered. Note 1: The CAP status bit will be set when the capture event has occurred. No further captures will occur until CAP is cleared by software.  2017-2019 Microchip Technology Inc. DS70005319D-page 515 dsPIC33CH128MP508 FAMILY REGISTER 9-14: PGxSTAT: PWM GENERATOR x STATUS REGISTER (CONTINUED) bit 5 CAP: Capture Status bit(1) 1 = PWM Generator time base value has been captured in PGxCAP 0 = No capture has occurred bit 4 UPDATE: PWM Data Register Update Status bit 1 = PWM Data register update is pending – user Data registers are not writable 0 = No PWM Data register update is pending bit 3 UPDREQ: PWM Data Register Update Request bit User software writes a ‘1’ to this bit location to request a PWM Data register update. The bit location always reads as ‘0’. The UPDATE status bit will indicate ‘1’ when an update is pending. bit 2 STEER: Output Steering Status bit (Push-Pull Output mode only) 1 = PWM Generator is in 2nd cycle of Push-Pull mode 0 = PWM Generator is in 1st cycle of Push-Pull mode bit 1 CAHALF: Half Cycle Status bit (Center-Aligned modes only) 1 = PWM Generator is in 2nd half of time base cycle 0 = PWM Generator is in 1st half of time base cycle bit 0 TRIG: PWM Trigger Status bit 1 = PWM Generator is triggered and PWM cycle is in progress 0 = No PWM cycle is in progress Note 1: The CAP status bit will be set when the capture event has occurred. No further captures will occur until CAP is cleared by software. DS70005319D-page 516  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 9-15: PGxIOCONL: PWM GENERATOR x I/O CONTROL REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CLMOD SWAP OVRENH OVRENL OVRDAT1 OVRDAT0 OSYNC1 OSYNC0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FLTDAT1 FLTDAT0 CLDAT1 CLDAT0 FFDAT1 FFDAT0 DBDAT1 DBDAT0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 CLMOD: Current-Limit Mode Select bit 1 = If PCI current limit is active, then the PWMxH and PWMxL output signals are inverted (bit flipping), and the CLDAT[1:0] bits are not used 0 = If PCI current limit is active, then the CLDAT[1:0] bits define the PWM output levels bit 14 SWAP: Swap PWM Signals to PWMxH and PWMxL Device Pins bit 1 = The PWMxH signal is connected to the PWMxL pin and the PWMxL signal is connected to the PWMxH pin 0 = PWMxH/L signals are mapped to their respective pins bit 13 OVRENH: User Override Enable for PWMxH Pin bit 1 = OVRDAT1 provides data for output on the PWMxH pin 0 = PWM Generator provides data for the PWMxH pin bit 12 OVRENL: User Override Enable for PWMxL Pin bit 1 = OVRDAT0 provides data for output on the PWMxL pin 0 = PWM Generator provides data for the PWMxL pin bit 11-10 OVRDAT[1:0]: Data for PWMxH/PWMxL Pins if Override is Enabled bits If OVERENH = 1, then OVRDAT1 provides data for PWMxH. If OVERENL = 1, then OVRDAT0 provides data for PWMxL. bit 9-8 OSYNC[1:0]: User Output Override Synchronization Control bits 11 = Reserved 10 = User output overrides via the OVRENH/L and OVRDAT[1:0] bits occur when specified by the UPDMOD[2:0] bits in the PGxCONH register 01 = User output overrides via the OVRENH/L and OVRDAT[1:0] bits occur immediately (as soon as possible) 00 = User output overrides via the OVRENH/L and OVRDAT[1:0] bits are synchronized to the local PWM time base (next Start-of-Cycle) bit 7-6 FLTDAT[1:0]: Data for PWMxH/PWMxL Pins if Fault Event is Active bits If Fault is active, then FLTDAT1 provides data for PWMxH. If Fault is active, then FLTDAT0 provides data for PWMxL. bit 5-4 CLDAT[1:0]: Data for PWMxH/PWMxL Pins if Current-Limit Event is Active bits If current limit is active, then CLDAT1 provides data for PWMxH. If current limit is active, then CLDAT0 provides data for PWMxL. bit 3-2 FFDAT[1:0]: Data for PWMxH/PWMxL Pins if Feed-Forward Event is Active bits If feed-forward is active, then FFDAT1 provides data for PWMxH. If feed-forward is active, then FFDAT0 provides data for PWMxL. bit 1-0 DBDAT[1:0]: Data for PWMxH/PWMxL Pins if Debug Mode is Active bits If Debug mode is active and PTFRZ = 1, then DBDAT1 provides data for PWMxH. If Debug mode is active and PTFRZ = 1, then DBDAT0 provides data for PWMxL.  2017-2019 Microchip Technology Inc. DS70005319D-page 517 dsPIC33CH128MP508 FAMILY REGISTER 9-16: U-0 — PGxIOCONH: PWM GENERATOR x I/O CONTROL REGISTER HIGH R/W-0 R/W-0 R/W-0 CAPSRC2(1) CAPSRC1(1) CAPSRC0(1) U-0 U-0 U-0 R/W-0 — — — DTCMPSEL bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — PMOD1 PMOD0 PENH PENL POLH POLL bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 CAPSRC[2:0]: Time Base Capture Source Selection bits(1) 111 = Reserved 110 = Reserved 101 = Reserved 100 = Capture time base value at assertion of selected PCI Fault signal 011 = Capture time base value at assertion of selected PCI current-limit signal 010 = Capture time base value at assertion of selected PCI feed-forward signal 001 = Capture time base value at assertion of selected PCI Sync signal 000 = No hardware source selected for time base capture – software only bit 11-9 Unimplemented: Read as ‘0’ bit 8 DTCMPSEL: Dead-Time Compensation Select bit 1 = Dead-time compensation is controlled by PCI feed-forward limit logic 0 = Dead-time compensation is controlled by PCI Sync logic bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 PMOD[1:0]: PWM Generator Output Mode Selection bits 11 = Reserved 10 = PWM Generator outputs operate in Push-Pull mode 01 = PWM Generator outputs operate in Independent mode 00 = PWM Generator outputs operate in Complementary mode bit 3 PENH: PWMxH Output Port Enable bit 1 = PWM Generator controls the PWMxH output pin 0 = PWM Generator does not control the PWMxH output pin bit 2 PENL: PWMxL Output Port Enable bit 1 = PWM Generator controls the PWMxL output pin 0 = PWM Generator does not control the PWMxL output pin bit 1 POLH: PWMxH Output Polarity bit 1 = Output pin is active-low 0 = Output pin is active-high bit 0 POLL: PWMxL Output Polarity bit 1 = Output pin is active-low 0 = Output pin is active-high Note 1: A capture may be initiated in software at any time by writing a ‘1’ to CAP (PGxSTAT[5]). DS70005319D-page 518  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 9-17: PGxyPCIL: PWM GENERATOR xy PCI REGISTER LOW (x = PWM GENERATOR #; y = F, CL, FF OR S) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TSYNCDIS TERM2 TERM1 TERM0 AQPS AQSS2 AQSS1 AQSS0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SWTERM PSYNC PPS PSS4 PSS3 PSS2 PSS1 PSS0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 TSYNCDIS: Termination Synchronization Disable bit 1 = Termination of latched PCI occurs immediately 0 = Termination of latched PCI occurs at PWM EOC bit 14-12 TERM[2:0]: Termination Event Selection bits 111 = Selects PCI Source #9 110 = Selects PCI Source #8 101 = Selects PCI Source #1 (PWM Generator output selected by the PWMPCI[2:0] bits) 100 = PGxTRIGC trigger event 011 = PGxTRIGB trigger event 010 = PGxTRIGA trigger event 001 = Auto-Terminate: Terminate when PCI source transitions from active to inactive 000 = Manual Terminate: Terminate on a write of ‘1’ to the SWTERM bit location bit 11 AQPS: Acceptance Qualifier Polarity Select bit 1 = Inverted 0 = Not inverted bit 10-8 AQSS[2:0]: Acceptance Qualifier Source Selection bits 111 = SWPCI control bit only (qualifier forced to ‘0’) 110 = Selects PCI Source #9 101 = Selects PCI Source #8 100 = Selects PCI Source #1 (PWM Generator output selected by the PWMPCI[2:0] bits) 011 = PWM Generator is triggered 010 = LEB is active 001 = Duty cycle is active (base PWM Generator signal) 000 = No acceptance qualifier is used (qualifier forced to ‘1’) bit 7 SWTERM: PCI Software Termination bit A write of ‘1’ to this location will produce a termination event. This bit location always reads as ‘0’. bit 6 PSYNC: PCI Synchronization Control bit 1 = PCI source is synchronized to PWM EOC 0 = PCI source is not synchronized to PWM EOC bit 5 PPS: PCI Polarity Select bit 1 = Inverted 0 = Not inverted  2017-2019 Microchip Technology Inc. DS70005319D-page 519 dsPIC33CH128MP508 FAMILY REGISTER 9-17: bit 4-0 PGxyPCIL: PWM GENERATOR xy PCI REGISTER LOW (x = PWM GENERATOR #; y = F, CL, FF OR S) (CONTINUED) PSS[4:0]: PCI Source Selection bits For Master: 11111 = Master CLC1 11110 = Slave Comparator 3 output 11101 = Slave Comparator 2 output 11100 = Slave Comparator 1 output 11011 = Master Comparator 1 output 11010 = Slave PWM Event F 11001 = Slave PWM Event E 11000 = Slave PWM Event D 10111 = Slave PWM Event C 10110 = Device pin, PCI[22] 10101 = Device pin, PCI[21] 10100 = Device pin, PCI[20] 10011 = Device pin, PCI[19] 10010 = Master RPn input, Master PCI18R 10001 = Master RPn input, Master PCI17R 10000 = Master RPn input, Master PCI16R 01111 = Master RPn input, Master PCI15R 01110 = Master RPn input, Master PCI14R 01101 = Master RPn input, Master PCI13R 01100 = Master RPn input, Master PCI12R 01011 = Master RPn input, Master PCI11R 01010 = Master RPn input, Master PCI10R 01001 = Master RPn input, Master PCI9R 01000 = Master RPn input, Master PCI8R 00111 = Reserved 00110 = Reserved 00101 = Reserved 00100 = Reserved 00011 = Internally connected to Combo Trigger B 00010 = Internally connected to Combo Trigger A 00001 = Internally connected to the output of PWMPCI[2:0] MUX 00000 = Tied to ‘0’ DS70005319D-page 520  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 9-17: PGxyPCIL: PWM GENERATOR xy PCI REGISTER LOW (x = PWM GENERATOR #; y = F, CL, FF OR S) (CONTINUED) For Slave: PWM_PCI[n] Source 00111 = Reserved 00110 = Reserved 00101 = Reserved 00100 = Reserved 00011 = Internally connected to Combo Trigger B 00010 = Internally connected to Combo Trigger A 00001 = Internally connected to the output of PWMPCI[2:0] MUX 00000 = Internally connect to ‘1’b0’ 11111 = Slave CLC1 11110 = Slave Comparator Output 3 11101 = Slave Comparator Output 2 11100 = Slave Comparator Output 1 11011 = Master Comparator Output 1 11010 = Master PWM Event F 11001 = Master PWM Event E 11000 = Master PWM Event D 10111 = Master PWM Event C 10110 = PCI[22] device pin device none PCI[22] 10101 = PCI[21] device pin device none PCI[21] 10100 = PCI[20] device pin device none PCI[20] 10011 = Device pin device none PCI[19] 10010 = Slave S1RPn input Slave PCI18R 10001 = Slave S1RPn input Slave PCI17R 10000 = Slave S1RPn input Slave PCI16R 01111 = Slave S1RPn input Slave PCI15R 01110 = Slave S1RPn input Slave PCI14R 01101 = Slave S1RPn input Slave PCI13R 01100 = Slave S1RPn input Slave PCI12R 01011 = Slave S1RPn input Slave PCI11R 01010 = Slave S1RPn input Slave PCI10R 01001 = Slave S1RPn input Slave PCI9R 01000 = Slave S1RPn input Slave PCI8R  2017-2019 Microchip Technology Inc. DS70005319D-page 521 dsPIC33CH128MP508 FAMILY REGISTER 9-18: PGxyPCIH: PWM GENERATOR xy PCI REGISTER HIGH (x = PWM GENERATOR #; y = F, CL, FF OR S) R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 BPEN BPSEL2(1) BPSEL1(1) BPSEL0(1) — ACP2 ACP1 ACP0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SWPCI SWPCIM1 SWPCIM0 LATMOD TQPS TQSS2 TQSS1 TQSS0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 BPEN: PCI Bypass Enable bit 1 = PCI function is enabled and local PCI logic is bypassed; PWM Generator will be controlled by PCI function in the PWM Generator selected by the BPSEL[2:0] bits 0 = PCI function is not bypassed bit 14-12 BPSEL[2:0]: PCI Bypass Source Selection bits(1) 111 = PCI control is sourced from PWM Generator 8 PCI logic when BPEN = 1 110 = PCI control is sourced from PWM Generator 7 PCI logic when BPEN = 1 101 = PCI control is sourced from PWM Generator 6 PCI logic when BPEN = 1 100 = PCI control is sourced from PWM Generator 5 PCI logic when BPEN = 1 011 = PCI control is sourced from PWM Generator 4 PCI logic when BPEN = 1 010 = PCI control is sourced from PWM Generator 3 PCI logic when BPEN = 1 001 = PCI control is sourced from PWM Generator 2 PCI logic when BPEN = 1 000 = PCI control is sourced from PWM Generator 1 PCI logic when BPEN = 1 bit 11 Unimplemented: Read as ‘0’ bit 10-8 ACP[2:0]: PCI Acceptance Criteria Selection bits 111 = Reserved 110 = Reserved 101 = Latched any edge 100 = Latched rising edge 011 = Latched 010 = Any edge 001 = Rising edge 000 = Level-sensitive bit 7 SWPCI: Software PCI Control bit 1 = Drives a ‘1’ to PCI logic assigned to by the SWPCIM[1:0] control bits 0 = Drives a ‘0’ to PCI logic assigned to by the SWPCIM[1:0] control bits bit 6-5 SWPCIM[1:0]: Software PCI Control Mode bits 11 = Reserved 10 = SWPCI bit is assigned to termination qualifier logic 01 = SWPCI bit is assigned to acceptance qualifier logic 00 = SWPCI bit is assigned to PCI acceptance logic bit 4 LATMOD: PCI SR Latch Mode bit 1 = SR latch is Reset-dominant in Latched Acceptance modes 0 = SR latch is Set-dominant in Latched Acceptance modes Note 1: Selects ‘0’ if selected PWM Generator is not present. DS70005319D-page 522  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 9-18: PGxyPCIH: PWM GENERATOR xy PCI REGISTER HIGH (x = PWM GENERATOR #; y = F, CL, FF OR S) (CONTINUED) bit 3 TQPS: Termination Qualifier Polarity Select bit 1 = Inverted 0 = Not inverted bit 2-0 TQSS[2:0]: Termination Qualifier Source Selection bits 111 = SWPCI control bit only (qualifier forced to ‘0’) 110 = Selects PCI Source #9 101 = Selects PCI Source #8 100 = Selects PCI Source #1 (PWM Generator output selected by the PWMPCI[2:0] bits) 011 = PWM Generator is triggered 010 = LEB is active 001 = Duty cycle is active (base PWM Generator signal) 000 = No termination qualifier used (qualifier forced to ‘1’) Note 1: Selects ‘0’ if selected PWM Generator is not present.  2017-2019 Microchip Technology Inc. DS70005319D-page 523 dsPIC33CH128MP508 FAMILY REGISTER 9-19: R/W-0 R/W-0 PGxEVTL: PWM GENERATOR x EVENT REGISTER LOW R/W-0 R/W-0 R/W-0 ADTR1PS4 ADTR1PS3 ADTR1PS2 ADTR1PS1 ADTR1PS0 R/W-0 R/W-0 R/W-0 ADTR1EN3 ADTR1EN2 ADTR1EN1 bit 15 bit 8 U-0 U-0 U-0 R/W-0 — — — UPDTRG1 R/W-0 R/W-0 R/W-0 R/W-0 UPDTRG0 PGTRGSEL2(1) PGTRGSEL1(1) PGTRGSEL0(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-11 ADTR1PS[4:0]: ADC Trigger 1 Postscaler Selection bits 11111 = 1:32 ... 00010 = 1:3 00001 = 1:2 00000 = 1:1 bit 10 ADTR1EN3: ADC Trigger 1 Source is PGxTRIGC Compare Event Enable bit 1 = PGxTRIGC register compare event is enabled as trigger source for ADC Trigger 1 0 = PGxTRIGC register compare event is disabled as trigger source for ADC Trigger 1 bit 9 ADTR1EN2: ADC Trigger 1 Source is PGxTRIGB Compare Event Enable bit 1 = PGxTRIGB register compare event is enabled as trigger source for ADC Trigger 1 0 = PGxTRIGB register compare event is disabled as trigger source for ADC Trigger 1 bit 8 ADTR1EN1: ADC Trigger 1 Source is PGxTRIGA Compare Event Enable bit 1 = PGxTRIGA register compare event is enabled as trigger source for ADC Trigger 1 0 = PGxTRIGA register compare event is disabled as trigger source for ADC Trigger 1 bit 7-5 Unimplemented: Read as ‘0’ bit 4-3 UPDTRG[1:0]: Update Trigger Select bits 11 = A write of the PGxTRIGA register automatically sets the UPDATE bit 10 = A write of the PGxPHASE register automatically sets the UPDATE bit 01 = A write of the PGxDC register automatically sets the UPDATE bit 00 = User must set the UPDREQ bit (PGxSTAT[4]) manually bit 2-0 PGTRGSEL[2:0]: PWM Generator Trigger Output Selection bits(1) 111 = Reserved 110 = Reserved 101 = Reserved 100 = Reserved 011 = PGxTRIGC compare event is the PWM Generator trigger 010 = PGxTRIGB compare event is the PWM Generator trigger 001 = PGxTRIGA compare event is the PWM Generator trigger 000 = EOC event is the PWM Generator trigger Note 1: These events are derived from the internal PWM Generator time base comparison events. DS70005319D-page 524  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 9-20: R/W-0 (1) FLTIEN PGxEVTH: PWM GENERATOR x EVENT REGISTER HIGH R/W-0 (2) CLIEN R/W-0 FFIEN R/W-0 (3) (4) SIEN U-0 U-0 R/W-0 R/W-0 — — IEVTSEL1 IEVTSEL0 bit 15 R/W-0 bit 8 R/W-0 ADTR2EN3 ADTR2EN2 R/W-0 ADTR2EN1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ADTR1OFS4 ADTR1OFS3 ADTR1OFS2 ADTR1OFS1 ADTR1OFS0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 FLTIEN: PCI Fault Interrupt Enable bit(1) 1 = Fault interrupt is enabled 0 = Fault interrupt is disabled bit 14 CLIEN: PCI Current-Limit Interrupt Enable bit(2) 1 = Current-limit interrupt is enabled 0 = Current-limit interrupt is disabled bit 13 FFIEN: PCI Feed-Forward Interrupt Enable bit(3) 1 = Feed-forward interrupt is enabled 0 = Feed-forward interrupt is disabled bit 12 SIEN: PCI Sync Interrupt Enable bit(4) 1 = Sync interrupt is enabled 0 = Sync interrupt is disabled bit 11-10 Unimplemented: Read as ‘0’ bit 9-8 IEVTSEL[1:0]: Interrupt Event Selection bits 11 = Time base interrupts are disabled (Sync, Fault, current-limit and feed-forward events can be independently enabled) 10 = Interrupts CPU at ADC Trigger 1 event 01 = Interrupts CPU at TRIGA compare event 00 = Interrupts CPU at EOC bit 7 ADTR2EN3: ADC Trigger 2 Source is PGxTRIGC Compare Event Enable bit 1 = PGxTRIGC register compare event is enabled as trigger source for ADC Trigger 2 0 = PGxTRIGC register compare event is disabled as trigger source for ADC Trigger 2 bit 6 ADTR2EN2: ADC Trigger 2 Source is PGxTRIGB Compare Event Enable bit 1 = PGxTRIGB register compare event is enabled as trigger source for ADC Trigger 2 0 = PGxTRIGB register compare event is disabled as trigger source for ADC Trigger 2 bit 5 ADTR2EN1: ADC Trigger 2 Source is PGxTRIGA Compare Event Enable bit 1 = PGxTRIGA register compare event is enabled as trigger source for ADC Trigger 2 0 = PGxTRIGA register compare event is disabled as trigger source for ADC Trigger 2 Note 1: 2: 3: 4: An interrupt is only generated on the rising edge of the PCI Fault active signal. An interrupt is only generated on the rising edge of the PCI current-limit active signal. An interrupt is only generated on the rising edge of the PCI feed-forward active signal. An interrupt is only generated on the rising edge of the PCI Sync active signal.  2017-2019 Microchip Technology Inc. DS70005319D-page 525 dsPIC33CH128MP508 FAMILY REGISTER 9-20: bit 4-0 Note 1: 2: 3: 4: ADTR1OFS[4:0]: ADC Trigger 1 Offset Selection bits 11111 = Offset by 31 trigger events ... 00010 = Offset by 2 trigger events 00001 = Offset by 1 trigger event 00000 = No offset An interrupt is only generated on the rising edge of the PCI Fault active signal. An interrupt is only generated on the rising edge of the PCI current-limit active signal. An interrupt is only generated on the rising edge of the PCI feed-forward active signal. An interrupt is only generated on the rising edge of the PCI Sync active signal. REGISTER 9-21: R/W-0 PGxEVTH: PWM GENERATOR x EVENT REGISTER HIGH (CONTINUED) PGxLEBL: PWM GENERATOR x LEADING-EDGE BLANKING REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 LEB[15:8] bit 15 R/W-0 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R-0 R-0 R-0 LEB[7:0](1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: x = Bit is unknown LEB[15:0]: Leading-Edge Blanking Period bits(1) Bits[2:0] are read-only and always remain as ‘0’. DS70005319D-page 526  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 9-22: U-0 U-0 — — PGxLEBH: PWM GENERATOR x LEADING-EDGE BLANKING REGISTER HIGH U-0 — U-0 — U-0 R/W-0 — R/W-0 PWMPCI[2:0] R/W-0 (1) bit 15 bit 8 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — — PHR PHF PLR PLF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-11 Unimplemented: Read as ‘0’ bit 10-8 PWMPCI[2:0]: PWM Source for PCI Selection bits(1) 111 = PWM Generator #8 output is made available to PCI logic 110 = PWM Generator #7 output is made available to PCI logic 101 = PWM Generator #6 output is made available to PCI logic 100 = PWM Generator #5 output is made available to PCI logic 011 = PWM Generator #4 output is made available to PCI logic 010 = PWM Generator #3 output is made available to PCI logic 001 = PWM Generator #2 output is made available to PCI logic 000 = PWM Generator #1 output is made available to PCI logic bit 7-4 Unimplemented: Read as ‘0’ bit 3 PHR: PWMxH Rising bit 1 = Rising edge of PWMxH will trigger the LEB duration counter 0 = LEB ignores the rising edge of PWMxH bit 2 PHF: PWMxH Falling bit 1 = Falling edge of PWMxH will trigger the LEB duration counter 0 = LEB ignores the falling edge of PWMxH bit 1 PLR: PWMxL Rising bit 1 = Rising edge of PWMxL will trigger the LEB duration counter 0 = LEB ignores the rising edge of PWMxL bit 0 PLF: PWMxL Falling bit 1 = Falling edge of PWMxL will trigger the LEB duration counter 0 = LEB ignores the falling edge of PWMxL Note 1: x = Bit is unknown The selected PWM Generator source does not affect the LEB counter. This source can be optionally used as a PCI input, PCI qualifier, PCI terminator or PCI terminator qualifier (see the description in Register 9-17 and Register 9-18 for more information).  2017-2019 Microchip Technology Inc. DS70005319D-page 527 dsPIC33CH128MP508 FAMILY REGISTER 9-23: R/W-0 PGxPHASE: PWM GENERATOR x PHASE REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PGxPHASE[15:8] bit 15 R/W-0 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PGxPHASE[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 PGxPHASE[15:0]: PWM Generator x Phase Register bits REGISTER 9-24: R/W-0 x = Bit is unknown PGxDC: PWM GENERATOR x DUTY CYCLE REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PGxDC[15:8] bit 15 R/W-0 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PGxDC[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown PGxDC[15:0]: PWM Generator x Duty Cycle Register bits DS70005319D-page 528  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 9-25: PGxDCA: PWM GENERATOR x DUTY CYCLE ADJUSTMENT REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 R/W-0 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PGxDCA[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7-0 PGxDCA[7:0]: PWM Generator x Duty Cycle Adjustment Value bits Depending on the state of the selected PCI source, the PGxDCA value will be added to the value in the PGxDC register to create the effective duty cycle. When the PCI source is active, PGxDCA is added. When the PCI source is inactive, no adjustment is made. Duty cycle adjustment is disabled when PGxDCA[7:0] = 0. The PCI source is selected using the DTCMPSEL bit. REGISTER 9-26: R/W-0 PGxPER: PWM GENERATOR x PERIOD REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PGxPER[15:8](1) bit 15 R/W-0 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PGxPER[7:0](1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: x = Bit is unknown PGxPER[15:0]: PWM Generator x Period Register bits(1) Period values less than ‘0x0010’ should not be selected.  2017-2019 Microchip Technology Inc. DS70005319D-page 529 dsPIC33CH128MP508 FAMILY REGISTER 9-27: R/W-0 PGxTRIGA: PWM GENERATOR x TRIGGER A REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PGxTRIGA[15:8] bit 15 R/W-0 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PGxTRIGA[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 PGxTRIGA[15:0]: PWM Generator x Trigger A Register bits REGISTER 9-28: R/W-0 x = Bit is unknown PGxTRIGB: PWM GENERATOR x TRIGGER B REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PGxTRIGB[15:8] bit 15 R/W-0 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PGxTRIGB[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 PGxTRIGB[15:0]: PWM Generator x Trigger B Register bits REGISTER 9-29: R/W-0 x = Bit is unknown PGxTRIGC: PWM GENERATOR x TRIGGER C REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PGxTRIGC[15:8] bit 15 R/W-0 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PGxTRIGC[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown PGxTRIGC[15:0]: PWM Generator x Trigger C Register bits DS70005319D-page 530  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 9-30: U-0 PGxDTL: PWM GENERATOR x DEAD-TIME REGISTER LOW U-0 — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — DTL[13:8] bit 15 R/W-0 R/W-0 (1) bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DTL[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-14 Unimplemented: Read as ‘0’ bit 13-0 DTL[13:0]: PWMxL Dead-Time Delay bits(1) Note 1: x = Bit is unknown DTL[13:11] bits are not available when HREN (PGxCONL[7]) = 0. REGISTER 9-31: U-0 PGxDTH: PWM GENERATOR x DEAD-TIME REGISTER HIGH U-0 — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — bit 15 R/W-0 R/W-0 DTH[13:8](1) bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DTH[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-14 Unimplemented: Read as ‘0’ bit 13-0 DTH[13:0]: PWMxH Dead-Time Delay bits(1) Note 1: x = Bit is unknown DTH[13:11] bits are not available when HREN (PGxCONL[7]) = 0.  2017-2019 Microchip Technology Inc. DS70005319D-page 531 dsPIC33CH128MP508 FAMILY REGISTER 9-32: R-0 PGxCAP: PWM GENERATOR x CAPTURE REGISTER R-0 R-0 R-0 R-0 R-0 R-0 R-0 PGxCAP[15:8] bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 (1) PGxCAP[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: x = Bit is unknown PGxCAP[15:0]: PGx Time Base Capture bits(1) A capture event can be manually initiated in software by writing a ‘1’ to PGxCAP[0]. The CAP bit (PGxSTAT[5]) will indicate when a new capture value is available. A read of PGxCAP will automatically clear the CAP bit and allow a new capture event to occur. PGxCAP[1:0] will always read as ‘0’. In High-Resolution mode, PGxCAP[4:0] will always read as ‘0’. DS70005319D-page 532  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 10.0 CAPTURE/COMPARE/PWM/ TIMER MODULES (SCCP) Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. For more information on the MCCP/SCCP modules, refer to “Capture/Compare/ PWM/Timer (MCCP and SCCP)” (www.microchip.com/DS30003035) in the “dsPIC33/PIC24 Family Reference Manual”. 2: The SCCP is identical for both Master core and Slave core. The x is common for both Master and Slave (where the x represents the number of the specific module being addressed). 3: All associated register names are the same on the Master core and the Slave core. The Slave code will be developed in a separate project in MPLAB® X IDE with the device selection, dsPIC33CH128MP508S1, where S1 indicates the Slave device. The Master SCCP modules are SCCP1, SCCP2, SCCP3, SCCP4, SSCCP5, SCCP6, SCCP7 and SCCP8. The Slave SCCP modules are SCCP1, SCCP2, SCCP3 and SCCP4. Table 10-1 shows an overview of the SCCP module. TABLE 10-1: SCCP MODULE OVERVIEW Number of SCCP Modules Identical (Modules) Master Core 8 Yes Slave Core 4 Yes  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 family devices include several Capture/Compare/PWM/Timer base modules, which provide the functionality of three different peripherals from earlier PIC24F devices. The module can operate in one of three major modes: • General Purpose Timer • Input Capture • Output Compare/PWM Single CCP (SCCP) output modules provide only one PWM output. The SCCP module can be operated only in one of the three major modes at any time. The other modes are not available unless the module is reconfigured for the new mode. A conceptual block diagram for the module is shown in Figure 10-1. All three modes share a time base generator and a common Timer register pair (CCPxTMRH/L); other shared hardware components are added as a particular mode requires. Each module has a total of six control and status registers: • • • • • • CCPxCON1L (Register 10-1) CCPxCON1H (Register 10-2) CCPxCON2L (Register 10-3) CCPxCON2H (Register 10-4) CCPxCON3H (Register 10-5) CCPxSTATL (Register 10-6) Each module also includes eight buffer/counter registers that serve as Timer Value registers or data holding buffers: • CCPxTMRH/CCPxTMRL (CCPx Timer High/Low Counters) • CCPxPRH/CCPxPRL (CCPx Timer Period High/Low) • CCPxRA (CCPx Primary Output Compare Data Buffer) • CCPxRB (CCPx Secondary Output Compare Data Buffer) • CCPxBUFH/CCPxBUFL (CCPx Input Capture High/Low Buffers) DS70005319D-page 533 dsPIC33CH128MP508 FAMILY FIGURE 10-1: SCCPx CONCEPTUAL BLOCK DIAGRAM CCPxIF External Capture Input Time Base Generator Clock Sources Compare/PWM Output(s) 16/32-Bit Timer Sync and Gating Sources Time Base Generator The Timer Clock Generator (TCG) generates a clock for the module’s internal time base, using one of the clock signals already available on the microcontroller. This is used as the time reference for the module in its three major modes. The internal time base is shown in Figure 10-2. FIGURE 10-2: Sync/Trigger Out CCPxTMRH/L T32 CCSEL MOD[3:0] 10.1 CCTxIF Input Capture Output Compare/ PWM OCFA/OCFB There are eight inputs available to the clock generator, which are selected using the CLKSEL[2:0] bits (CCPxCON1L[10:8]). Available sources include the FRC and LPRC, the Secondary Oscillator and the TCLKI External Clock inputs. The system clock is the default source (CLKSEL[2:0] = 000). TIMER CLOCK GENERATOR Clock Sources TMRPS[1:0] TMRSYNC SSDG Prescaler Clock Synchronizer Gate(1) To Rest of Module CLKSEL[2:0] Note 1: Gating is available in Timer modes only. DS70005319D-page 534  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 10.2 General Purpose Timer Timer mode is selected when CCSEL = 0 and MOD[3:0] = 0000. The timer can function as a 32-bit timer or a dual 16-bit timer, depending on the setting of the T32 bit (Table 10-2). TABLE 10-2: TIMER OPERATION MODE T32 (CCPxCON1L[5]) Operating Mode 0 Dual Timer Mode (16-bit) 1 Timer Mode (32-bit) Dual 16-Bit Timer mode provides a simple timer function with two independent 16-bit timer/counters. The primary timer uses CCPxTMRL and CCPxPRL. Only the primary timer can interact with other modules on the device. It generates the SCCPx sync out signals for use by other SCCP modules. It can also use the SYNC[4:0] bits signal generated by other modules. The secondary timer uses CCPxTMRH and CCPxPRH. It is intended to be used only as a periodic interrupt source for scheduling CPU events. It does not generate an output sync/trigger signal like the primary time base. In Dual Timer mode, the CCPx Secondary Timer Period register, CCPxPRH, generates the SCCP compare event (CCPxIF) used by many other modules on the device. 10.2.1 SYNC AND TRIGGER OPERATION In both 16-bit and 32-bit modes, the timer can also function in either synchronization (“sync”) or trigger operation. Both use the SYNC[4:0] bits (CCPxCON1H[4:0]) to determine the input signal source. The difference is how that signal affects the timer. In sync operation, the timer Reset or clear occurs when the input selected by SYNC[4:0] is asserted. The timer immediately begins to count again from zero unless it is held for some other reason. Sync operation is used whenever the TRIGEN bit (CCPxCON1H[7]) is cleared. SYNC[4:0] can have any value, except ‘11111’. In trigger operation, the timer is held in Reset until the input selected by SYNC[4:0] is asserted; when it occurs, the timer starts counting. Trigger operation is used whenever the TRIGEN bit is set. In Trigger mode, the timer will continue running after a trigger event as long as the CCPTRIG bit (CCPxSTATL[7]) is set. To clear CCPTRIG, the TRCLR bit (CCPxSTATL[5]) must be set to clear the trigger event, reset the timer and hold it at zero until another trigger event occurs. On dsPIC33CH128MP508 family devices, trigger operation can only be used when the system clock is the time base source (CLKSEL[2:0] = 000). The 32-Bit Timer mode uses the CCPxTMRL and CCPxTMRH registers, together, as a single 32-bit timer. When CCPxTMRL overflows, CCPxTMRH increments by one. This mode provides a simple timer function when it is important to track long time periods. Note that the T32 bit (CCPxCON1L[5]) should be set before the CCPxTMRL or CCPxPRH registers are written to initialize the 32-bit timer.  2017-2019 Microchip Technology Inc. DS70005319D-page 535 dsPIC33CH128MP508 FAMILY FIGURE 10-3: DUAL 16-BIT TIMER MODE CCPxPRL Comparator SYNC[4:0] Sync/ Trigger Control CCPxTMRL Comparator Clock Sources Set CCTxIF Special Event Trigger Time Base Generator CCPxRB CCPxTMRH Comparator Set CCPxIF CCPxPRH FIGURE 10-4: SYNC[4:0] Clock Sources 32-BIT TIMER MODE Sync/ Trigger Control Time Base Generator CCPxTMRH CCPxTMRL Comparator CCPxPRH DS70005319D-page 536 Set CCTxIF CCPxPRL  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 10.3 output pulses. Like most PIC® MCU peripherals, the Output Compare x module can also generate interrupts on a compare match event. Output Compare Mode Output Compare mode compares the Timer register value with the value of one or two Compare registers, depending on its mode of operation. The Output Compare x module, on compare match events, has the ability to generate a single output transition or a train of TABLE 10-3: Table 10-3 shows the various modes available in Output Compare modes. OUTPUT COMPARE x/PWMx MODES MOD[3:0] (CCPxCON1L[3:0]) T32 (CCPxCON1L[5]) Operating Mode 0001 0 Output High on Compare (16-bit) 0001 1 Output High on Compare (32-bit) 0010 0 Output Low on Compare (16-bit) 0010 1 Output Low on Compare (32-bit) 0011 0 Output Toggle on Compare (16-bit) 0011 1 Output Toggle on Compare (32-bit) 0100 0 Dual Edge Compare (16-bit) Dual Edge Mode 0101 0 Dual Edge Compare (16-bit buffered) PWM Mode FIGURE 10-5: Single Edge Mode OUTPUT COMPARE x BLOCK DIAGRAM CCPxCON1H/L CCPxCON2H/L CCPxPRL CCPxCON3H Comparator CCPxRA Rollover/Reset CCPxRA Buffer Comparator OCx Clock Sources Time Base Generator Increment CCPxTMRH/L Reset Trigger and Sync Sources Trigger and Sync Logic Match Event Comparator Match Event Rollover Match Event Edge Detect OCx Output, Auto-Shutdown and Polarity Control CCPx Pin(s) OCFA/OCFB Fault Logic CCPxRB Buffer Rollover/Reset CCPxRB Reset  2017-2019 Microchip Technology Inc. Output Compare Interrupt DS70005319D-page 537 dsPIC33CH128MP508 FAMILY 10.4 Input Capture Mode Input Capture mode is used to capture a timer value from an independent timer base, upon an event, on an input pin or other internal trigger source. The input capture features are useful in applications requiring frequency (time period) and pulse measurement. Figure 10-6 depicts a simplified block diagram of Input Capture mode. TABLE 10-4: Input Capture mode uses a dedicated 16/32-bit, synchronous, up counting timer for the capture function. The timer value is written to the FIFO when a capture event occurs. The internal value may be read (with a synchronization delay) using the CCPxTMRH/L register. To use Input Capture mode, the CCSEL bit (CCPxCON1L[4]) must be set. The T32 and the MOD[3:0] bits are used to select the proper Capture mode, as shown in Table 10-4. INPUT CAPTURE x MODES MOD[3:0] (CCPxCON1L[3:0]) T32 (CCPxCON1L[5]) Operating Mode 0000 0 Edge Detect (16-bit capture) 0000 1 Edge Detect (32-bit capture) 0001 0 Every Rising (16-bit capture) 0001 1 Every Rising (32-bit capture) 0010 0 Every Falling (16-bit capture) 0010 1 Every Falling (32-bit capture) 0011 0 Every Rising/Falling (16-bit capture) 0011 1 Every Rising/Falling (32-bit capture) 0100 0 Every 4th Rising (16-bit capture) 0100 1 Every 4th Rising (32-bit capture) 0101 0 Every 16th Rising (16-bit capture) 0101 1 Every 16th Rising (32-bit capture) FIGURE 10-6: INPUT CAPTURE x BLOCK DIAGRAM ICS[2:0] Clock Select ICx Clock Sources MOD[3:0] OPS[3:0] Edge Detect Logic and Clock Synchronizer Event and Interrupt Logic Set CCPxIF Increment Reset Trigger and Sync Sources Trigger and Sync Logic 16 CCPxTMRH/L 4-Level FIFO Buffer 16 T32 16 CCPxBUFx System Bus DS70005319D-page 538  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 10.5 Auxiliary Output The SCCPx modules have an auxiliary (secondary) output that provides other peripherals access to internal module signals. The auxiliary output is intended to connect to other SCCP modules, or other digital peripherals, to provide these types of functions: The type of output signal is selected using the AUXOUT[1:0] control bits (CCPxCON2H[4:3]). The type of output signal is also dependent on the module operating mode. • Time Base Synchronization • Peripheral Trigger and Clock Inputs • Signal Gating TABLE 10-5: AUXILIARY OUTPUT AUXOUT[1:0] CCSEL MOD[3:0] Comments 00 x xxxx Auxiliary output disabled No Output 01 0 0000 Time Base modes Time Base Period Reset or Rollover Special Event Trigger Output 10 No Output 11 01 0 10 11 01 Signal Description 1 0001 through 1111 xxxx Output Compare modes Time Base Period Reset or Rollover Output Compare Event Signal Output Compare Signal Input Capture modes Time Base Period Reset or Rollover 10 Reflects the Value of the ICDIS bit 11 Input Capture Event Signal  2017-2019 Microchip Technology Inc. DS70005319D-page 539 dsPIC33CH128MP508 FAMILY 10.6 SCCP Control/Status Registers REGISTER 10-1: CCPxCON1L: CCPx CONTROL 1 LOW REGISTERS R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CCPON — CCPSIDL CCPSLP TMRSYNC CLKSEL2(1) CLKSEL1(1) CLKSEL0(1) bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TMRPS1 TMRPS0 T32 CCSEL MOD3 MOD2 MOD1 MOD0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 CCPON: CCPx Module Enable bit 1 = Module is enabled with an operating mode specified by the MOD[3:0] control bits 0 = Module is disabled bit 14 Unimplemented: Read as ‘0’ bit 13 CCPSIDL: CCPx Stop in Idle Mode bit 1 = Discontinues module operation when device enters Idle mode 0 = Continues module operation in Idle mode bit 12 CCPSLP: CCPx Sleep Mode Enable bit 1 = Module continues to operate in Sleep modes 0 = Module does not operate in Sleep modes bit 11 TMRSYNC: Time Base Clock Synchronization bit 1 = Asynchronous module time base clock is selected and synchronized to the internal system clocks (CLKSEL[2:0]  000) 0 = Synchronous module time base clock is selected and does not require synchronization (CLKSEL[2:0] = 000) bit 10-8 CLKSEL[2:0]: CCPx Time Base Clock Select bits(1) 111 = External T1CK input 110 = Slave CLC2 101 = Slave CLC1 100 = Master CLC2 011 = Master CLC1 010 = FOSC 001 = Reference Clock (REFCLKO) 000 = FOSC/2 (FP) bit 7-6 TMRPS[1:0]: Time Base Prescale Select bits 11 = 1:64 Prescaler 10 = 1:16 Prescaler 01 = 1:4 Prescaler 00 = 1:1 Prescaler bit 5 T32: 32-Bit Time Base Select bit 1 = Uses 32-bit time base for timer, single edge output compare or input capture function 0 = Uses 16-bit time base for timer, single edge output compare or input capture function bit 4 CCSEL: Capture/Compare Mode Select bit 1 = Input Capture peripheral 0 = Output Compare/PWM/Timer peripheral (exact function is selected by the MOD[3:0] bits) Note 1: Clock selection is the same for the Master and the Slave. DS70005319D-page 540  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 10-1: bit 3-0 Note 1: CCPxCON1L: CCPx CONTROL 1 LOW REGISTERS (CONTINUED) MOD[3:0]: CCPx Mode Select bits For CCSEL = 1 (Input Capture modes): 1xxx = Reserved 011x = Reserved 0101 = Capture every 16th rising edge 0100 = Capture every 4th rising edge 0011 = Capture every rising and falling edge 0010 = Capture every falling edge 0001 = Capture every rising edge 0000 = Capture every rising and falling edge (Edge Detect mode) For CCSEL = 0 (Output Compare/Timer modes): 1111 = External Input mode: Pulse generator is disabled, source is selected by ICS[2:0] 1110 = Reserved 110x = Reserved 10xx = Reserved 0111 = Reserved 0110 = Reserved 0101 = Dual Edge Compare mode, buffered 0100 = Dual Edge Compare mode 0011 = 16-Bit/32-Bit Single Edge mode, toggles output on compare match 0010 = 16-Bit/32-Bit Single Edge mode, drives output low on compare match 0001 = 16-Bit/32-Bit Single Edge mode, drives output high on compare match 0000 = 16-Bit/32-Bit Timer mode, output functions are disabled Clock selection is the same for the Master and the Slave.  2017-2019 Microchip Technology Inc. DS70005319D-page 541 dsPIC33CH128MP508 FAMILY REGISTER 10-2: R/W-0 CCPxCON1H: CCPx CONTROL 1 HIGH REGISTERS R/W-0 (1) OPSSRC U-0 (2) RTRGEN — U-0 R/W-0 (3) — OPS3 R/W-0 OPS2 (3) R/W-0 OPS1 (3) R/W-0 OPS0(3) bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TRIGEN ONESHOT ALTSYNC SYNC4 SYNC3 SYNC2 SYNC1 SYNC0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 OPSSRC: Output Postscaler Source Select bit(1) 1 = Output postscaler scales module trigger output events 0 = Output postscaler scales time base interrupt events bit 14 RTRGEN: Retrigger Enable bit(2) 1 = Time base can be retriggered when TRIGEN bit = 1 0 = Time base may not be retriggered when TRIGEN bit = 1 bit 13-12 Unimplemented: Read as ‘0’ bit 11-8 OPS3[3:0]: CCPx Interrupt Output Postscale Select bits(3) 1111 = Interrupt every 16th time base period match 1110 = Interrupt every 15th time base period match ... 0100 = Interrupt every 5th time base period match 0011 = Interrupt every 4th time base period match or 4th input capture event 0010 = Interrupt every 3rd time base period match or 3rd input capture event 0001 = Interrupt every 2nd time base period match or 2nd input capture event 0000 = Interrupt after each time base period match or input capture event bit 7 TRIGEN: CCPx Trigger Enable bit 1 = Trigger operation of time base is enabled 0 = Trigger operation of time base is disabled bit 6 ONESHOT: One-Shot Trigger Mode Enable bit 1 = One-Shot Trigger mode is enabled; trigger duration is set by OSCNT[2:0] 0 = One-Shot Trigger mode is disabled bit 5 ALTSYNC: CCPx Alternate Synchronization Output Signal Select bit 1 = An alternate signal is used as the module synchronization output signal 0 = The module synchronization output signal is the Time Base Reset/rollover event bit 4-0 SYNC[4:0]: CCPx Synchronization Source Select bits See Table 10-6 and Table 10-7 for the definition of inputs. Note 1: 2: 3: This control bit has no function in Input Capture modes. This control bit has no function when TRIGEN = 0. Output postscale settings, from 1:5 to 1:16 (0100-1111), will result in a FIFO buffer overflow for Input Capture modes. DS70005319D-page 542  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 10-6: SYNCHRONIZATION SOURCES (MASTER) SYNC[4:0] Synchronization Source 00000 None; Timer with Rollover on CCPxPR Match or FFFFh 00001 Module’s Own Timer Sync Out 00010 Sync Output SCCP1 00011 Sync Output SCCP2 00100 Sync Output SCCP3 00101 Sync Output SCCP4 00110 Sync Output SCCP5 00111 Sync Output SCCP6 01000 Sync Output SCCP7 01001 INT0 01010 INT1 01011 01100-01111 INT2 Reserved 10000 Master CLC1 Output 10001 Master CLC2 Output 10010 Slave CLC1 Output 10011 Slave CLC2 Output 10100-10110 Reserved 10111 Comparator 1 Output 11000 Slave Comparator 1 Output 11001 Slave Comparator 2 Output 11010 Slave Comparator 3 Output 11011-11110 11111  2017-2019 Microchip Technology Inc. Reserved None; Timer with Auto-Rollover (FFFFh → 0000h) DS70005319D-page 543 dsPIC33CH128MP508 FAMILY TABLE 10-7: SYNCHRONIZATION SOURCES (SLAVE) SYNC[4:0] Synchronization Source 00000 None; Timer with Rollover on CCPxPR Match or FFFFh 00001 Module’s Own Timer Sync Out 00010 Sync Output SCCP1 00011 Sync Output SCCP2 00100 Sync Output SCCP3 00101 Sync Output SCCP4 00110-01000 Reserved 01001 INT0 01010 INT1 01011 INT2 01100-01111 Reserved 10000 Master CLC1 Output 10001 Master CLC2 Output 10010 Slave CLC1 Output 10011 Slave CLC2 Output 10100-10110 Reserved 10111 Master Comparator 1 Output 11000 Slave Comparator 1 Output 11001 Slave Comparator 2 Output 11010 Slave Comparator 3 Output 11011-11110 11111 DS70005319D-page 544 Reserved None; Timer with Auto-Rollover (FFFFh → 0000h)  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 10-3: CCPxCON2L: CCPx CONTROL 2 LOW REGISTERS R/W-0 R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 PWMRSEN ASDGM — SSDG — — — — bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ASDG[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 PWMRSEN: CCPx PWM Restart Enable bit 1 = ASEVT bit clears automatically at the beginning of the next PWM period, after the shutdown input has ended 0 = ASEVT bit must be cleared in software to resume PWM activity on output pins bit 14 ASDGM: CCPx Auto-Shutdown Gate Mode Enable bit 1 = Waits until the next Time Base Reset or rollover for shutdown to occur 0 = Shutdown event occurs immediately bit 13 Unimplemented: Read as ‘0’ bit 12 SSDG: CCPx Software Shutdown/Gate Control bit 1 = Manually forces auto-shutdown, timer clock gate or input capture signal gate event (setting of ASDGM bit still applies) 0 = Normal module operation bit 11-8 Unimplemented: Read as ‘0’ bit 7-0 ASDG[7:0]: CCPx Auto-Shutdown/Gating Source Enable bits 1 = ASDGx Source n is enabled (see Table 10-8 and Table 10-9 for auto-shutdown/gating sources) 0 = ASDGx Source n is disabled  2017-2019 Microchip Technology Inc. DS70005319D-page 545 dsPIC33CH128MP508 FAMILY TABLE 10-8: AUTO-SHUTDOWN AND GATING SOURCES (MASTER) Auto-Shutdown/Gating Source ASDG[x] Bit SCCP1 SCCP2 SCCP3 SCCP4 SCCP5 0 Master Comparator 1 Output 1 Slave Comparator 1 Output 2 Slave Comparator 2 Output 3 Master ICM1(1) Master ICM2(1) Master ICM3(1) Master ICM4(1) Master ICM5(1) 5 Master CLC1(1) 6 Master OCFA(1) 7 Master OCFB(1) Master ICM6(1) Master ICM7(1) Master ICM8(1) AUTO-SHUTDOWN AND GATING SOURCES (SLAVE) Auto-Shutdown/Gating Source ASDG[x] Bit SCCP1 SCCP2 SCCP3 0 Master Comparator 1 Output 1 Slave Comparator 1 Output 2 Slave Comparator 2 Output 3 SCCP4 Slave Comparator 3 Output Slave ICM1(1) Slave ICM2(1) Slave ICM3(1) Slave ICM4(1) CLC1(1) 5 Slave 6 Slave OCFA(1) 7 Slave OCFB(1) Note 1: SCCP8 Selected by Peripheral Pin Select (PPS). TABLE 10-9: 4 SCCP7 Slave Comparator 3 Output 4 Note 1: SCCP6 Selected by Peripheral Pin Select (PPS). DS70005319D-page 546  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 10-4: CCPxCON2H: CCPx CONTROL 2 HIGH REGISTERS R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 OENSYNC — — — — — — OCAEN bit 15 bit 8 R/W-0 R/W-0 ICGSM1 U-0 — ICGSM0 R/W-0 R/W-0 AUXOUT1 AUXOUT0 R/W-0 R/W-0 R/W-0 (1) (1) ICS0(1) ICS2 ICS1 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 OENSYNC: Output Enable Synchronization bit 1 = Update by output enable bits occurs on the next Time Base Reset or rollover 0 = Update by output enable bits occurs immediately bit 14-9 Unimplemented: Read as ‘0’ bit 8 OCAEN: Output Enable/Steering Control bit 1 = OCx pin is controlled by the CCPx module and produces an output compare or PWM signal 0 = OCx pin is not controlled by the CCPx module; the pin is available to the port logic or another peripheral multiplexed on the pin bit 7-6 ICGSM[1:0]: Input Capture Gating Source Mode Control bits 11 = Reserved 10 = One-Shot mode: Falling edge from gating source disables future capture events (ICDIS = 1) 01 = One-Shot mode: Rising edge from gating source enables future capture events (ICDIS = 0) 00 = Level-Sensitive mode: A high level from gating source will enable future capture events; a low level will disable future capture events bit 5 Unimplemented: Read as ‘0’ bit 4-3 AUXOUT[1:0]: Auxiliary Output Signal on Event Selection bits 11 = Input capture or output compare event; no signal in Timer mode 10 = Signal output is defined by module operating mode (see Table 10-5) 01 = Time base rollover event (all modes) 00 = Disabled bit 2-0 ICS[2:0]: Input Capture Source Select bits(1) 111 = Slave CLC2 output 110 = Slave CLC1 output 101 = Master CLC2 output 100 = Master CLC1 output 011 = Slave Comparator 2 output 010 = Slave Comparator 1 output 001 = Master Comparator 1 output 000 = SCCP Input Capture x (ICx) pin (PPS) Note 1: Common for both the Master and the Slave.  2017-2019 Microchip Technology Inc. DS70005319D-page 547 dsPIC33CH128MP508 FAMILY REGISTER 10-5: CCPxCON3H: CCPx CONTROL 3 HIGH REGISTERS R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 U-0 OETRIG OSCNT2 OSCNT1 OSCNT0 — — — — bit 15 bit 8 U-0 U-0 R/W-0 U-0 R/W-0 R/W-0 U-0 U-0 — — POLACE — PSSACE1 PSSACE0 — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 OETRIG: Output Enable on Trigger Control bit 1 = For Triggered mode (TRIGEN = 1): Module does not drive enabled output pins until triggered 0 = Normal output pin operation bit 14-12 OSCNT[2:0]: One-Shot Event Count bits 111 = Extends one-shot event by seven time base periods (eight time base periods total) 110 = Extends one-shot event by six time base periods (seven time base periods total) 101 = Extends one-shot event by five time base periods (six time base periods total) 100 = Extends one-shot event by four time base periods (five time base periods total) 011 = Extends one-shot event by three time base periods (four time base periods total) 010 = Extends one-shot event by two time base periods (three time base periods total) 001 = Extends one-shot event by one time base period (two time base periods total) 000 = Does not extend one-shot trigger event bit 11-6 Unimplemented: Read as ‘0’ bit 5 POLACE: CCPx Output Pin OCxA Polarity Control bit 1 = Output pin polarity is active low 0 = Output pin polarity is active high bit 4 Unimplemented: Read as ‘0’ bit 3-2 PSSACE[1:0]: PWMx Output Pin OCxA Shutdown State Control bits 11 = Pin is driven active when a shutdown event occurs 10 = Pin is driven inactive when a shutdown event occurs 0x = Pin is in high-impedance state when a shutdown event occurs bit 1-0 Unimplemented: Read as ‘0’ DS70005319D-page 548  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 10-6: CCPxSTATL: CCPx STATUS REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R-0 W1-0 W1-0 R/C-0 R/C-0 R/C-0 R/C-0 R/C-0 CCPTRIG TRSET TRCLR ASEVT SCEVT ICDIS ICOV ICBNE bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W1 = Write ‘1’ Only bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7 CCPTRIG: CCPx Trigger Status bit 1 = Timer has been triggered and is running 0 = Timer has not been triggered and is held in Reset bit 6 TRSET: CCPx Trigger Set Request bit Writes ‘1’ to this location to trigger the timer when TRIGEN = 1 (location always reads as ‘0’). bit 5 TRCLR: CCPx Trigger Clear Request bit Writes ‘1’ to this location to cancel the timer trigger when TRIGEN = 1 (location always reads as ‘0’). bit 4 ASEVT: CCPx Auto-Shutdown Event Status/Control bit 1 = A shutdown event is in progress; CCPx outputs are in the shutdown state 0 = CCPx outputs operate normally bit 3 SCEVT: Single Edge Compare Event Status bit 1 = A single edge compare event has occurred 0 = A single edge compare event has not occurred bit 2 ICDIS: Input Capture x Disable bit 1 = Event on Input Capture x pin (ICx) does not generate a capture event 0 = Event on Input Capture x pin will generate a capture event bit 1 ICOV: Input Capture x Buffer Overflow Status bit 1 = The Input Capture x FIFO buffer has overflowed 0 = The Input Capture x FIFO buffer has not overflowed bit 0 ICBNE: Input Capture x Buffer Status bit 1 = Input Capture x buffer has data available 0 = Input Capture x buffer is empty  2017-2019 Microchip Technology Inc. DS70005319D-page 549 dsPIC33CH128MP508 FAMILY NOTES: DS70005319D-page 550  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 11.0 HIGH-SPEED ANALOG COMPARATOR WITH SLOPE COMPENSATION DAC Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “High-Speed Analog Comparator Module” (www.microchip.com/ DS70005280) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 3.2 “Master Memory Organization” in this data sheet for device-specific register and bit information. 3: The comparator and DAC are identical for both Master core and Slave core. The module is similar for both Master core and Slave core (where the x represents the number of the specific modules being addressed in Master or Slave). The high-speed analog comparator module provides a method to monitor voltage, current and other critical signals in a power conversion application that may be too fast for the CPU and ADC to capture. There are a total of four comparator modules, one of which is controlled by the Master core and the remaining three by the Slave core. The analog comparator module can be used to implement Peak Current mode control, Critical Conduction mode (variable frequency) and Hysteretic Control mode. Table 11-1 shows an overview of the comparator/DAC module. TABLE 11-1: 11.1 The high-speed analog comparator module is comprised of a high-speed comparator, Pulse Density Modulation (PDM) DAC and a slope compensation unit. The slope compensation unit provides a userdefined slope which can be used to alter the DAC output. This feature is useful in applications, such as Peak Current mode control, where slope compensation is required to maintain the stability of the power supply. The user simply specifies the direction and rate of change for the slope compensation and the output of the DAC is modified accordingly. The DAC consists of a PDM unit, followed by a digitally controlled multiphase RC filter. The PDM unit uses a phase accumulator circuit to generate an output stream of pulses. The density of the pulse stream is proportional to the input data value, relative to the maximum value supported by the bit width of the accumulator. The output pulse density is representative of the desired output voltage. The pulse stream is filtered with an RC filter to yield an analog voltage. The output of the DAC is connected to the negative input of the comparator. The positive input of the comparator can be selected using a MUX from either of the input pins or the output of the PGAs. The comparator provides a high-speed operation with a typical delay of 15 ns. The output of the comparator is processed by the pulse stretcher and the digital filter blocks, which prevent comparator response to unintended fast transients in the inputs. Figure 11-1 shows a block diagram of the high-speed analog comparator module. The DAC module can be operated in one of three modes: Slope Generation mode, Hysteretic mode and Triangle Wave mode. Each of these modes can be used in a variety of power supply applications. Note: The DACOUT1 pin can only be associated with a single DAC or PGA output at any given time. If more than one DACOEN bit is set, or the PGA Output Enable bit (PGAOEN) and the DACOEN bit are set, the DACOUT1 pin will be a combination of the signals. Note: DAC input frequency needs to be 500 MHz. COMPARATOR/DAC MODULE OVERVIEW Number of Comparator Modules Identical (Modules) Master Core 1 Yes Slave Core 3 Yes  2017-2019 Microchip Technology Inc. Overview DS70005319D-page 551 dsPIC33CH128MP508 FAMILY FIGURE 11-1: HIGH-SPEED ANALOG COMPARATOR MODULE BLOCK DIAGRAM INSEL[2:0] SPGA3 SPGA2 CMPx SPGA1 CMPxD/S1CMPxD PWM Trigger + 0 CMPxB/S1CMPxB – CMPxA/S1CMPxA 1 Pulse Stretcher and Digital Filter Status IRQ CMPPOL Slope Generator n DACx PDM DAC 4 DACOUT1 SPGA1 n SLPxDAT n n DACxDATH SPGA2 SPGA3 DACxDATL Note: n = 16 DS70005319D-page 552  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 11.2 Features Overview • Four Rail-to-Rail Analog Comparators • Up to Five Selectable Input Sources per Comparator: - Three external inputs - Two internal inputs from PGA module • Programmable Comparator Hysteresis • Programmable Output Polarity • Interrupt Generation Capability • Dedicated Pulse Density Modulation DAC for each Analog Comparator: - PDM unit followed by a digitally controlled multimode multipole RC filter • Multimode Multipole RC Output Filter: - Transition mode: Provides the fastest response - Fast mode: For tracking DAC slopes - Steady-State mode: Provides 12-bit resolution • Slope Compensation along with each DAC: - Slope Generation mode - Hysteretic Control mode - Triangle Wave mode • Functional Support for the High-Speed PWM module which Includes: - PWM duty cycle control - PWM period control - PWM Fault detect  2017-2019 Microchip Technology Inc. 11.3 DAC Control Registers The DACCTRL1L and DACCTRL2H/L registers are common configuration registers for Master and Slave DAC modules. The Master and Slave DAC modules are controlled by separate sets of DACCTRL1/2 registers. The DACxCON, DACxDAT, SLPxCON and SLPxDAT registers specify the operation of individual modules. Note that x = 1 for the Master module and x = 1-3 for the Slave modules. DS70005319D-page 553 dsPIC33CH128MP508 FAMILY REGISTER 11-1: DACCTRL1L: DAC CONTROL 1 LOW REGISTER R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0 DACON — DACSIDL — — — — — bit 15 bit 8 R/W-0 CLKSEL1 R/W-0 (1) CLKSEL0 R/W-0 (1) CLKDIV1 R/W-0 (1) U-0 (1) CLKDIV0 — R/W-0 FCLKDIV2 R/W-0 (2) R/W-0 (2) FCLKDIV1 FCLKDIV0(2) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 DACON: Common DAC Module Enable bit 1 = Enables DAC modules 0 = Disables DAC modules and disables FSCM clocks to reduce power consumption; any pending Slope mode and/or underflow conditions are cleared bit 14 Unimplemented: Read as ‘0’ bit 13 DACSIDL: DAC Stop in Idle Mode bit 1 = Discontinues module operation when device enters Idle mode 0 = Continues module operation in Idle mode bit 12-8 Unimplemented: Read as ‘0’ bit 7-6 CLKSEL[1:0]: DAC Clock Source Select bits(1) 11 = FPLLO 10 = AFPLLO 01 = FVCO/2 00 = AFVCO/2 bit 5-4 CLKDIV[1:0]: DAC Clock Divider bits (DAC should be operated at 500 MHz)(1,3) 11 = Divide-by-4 10 = Divide-by-3 (non-uniform duty cycle) 01 = Divide-by-2 00 = 1x bit 3 Unimplemented: Read as ‘0’ bit 2-0 FCLKDIV[2:0]: Comparator Filter Clock Divider bits(2) 111 = Divide-by-8 110 = Divide-by-7 101 = Divide-by-6 100 = Divide-by-5 011 = Divide-by-4 010 = Divide-by-3 001 = Divide-by-2 000 = 1x Note 1: 2: 3: These bits should only be changed when DACON = 0 to avoid unpredictable behavior. The input clock to this divider is the selected clock input, CLKSEL[1:0], and then divided by two. Clock source and dividers should yield an effective DAC clock input of 500 MHz. DS70005319D-page 554  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 11-2: DACCTRL2H: DAC CONTROL 2 HIGH REGISTER U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — R/W-0 R/W-0 SSTIME[9:8](1) bit 15 bit 8 R/W-1 R/W-0 R/W-0 R/W-0 R/W-1 R/W-0 R/W-1 R/W-0 SSTIME[7:0](1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-10 Unimplemented: Read as ‘0’ bit 9-0 SSTIME[9:0]: Time from Start of Transition Mode until Steady-State Filter is Enabled bits(1) Note 1: The value for SSTIME[9:0] should be greater than the TMODTIME[9:0] value. REGISTER 11-3: DACCTRL2L: DAC CONTROL 2 LOW REGISTER U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — R/W-0 R/W-0 TMODTIME[9:8](1) bit 15 bit 8 R/W-0 R/W-1 R/W-0 R/W-1 R/W-0 TMODTIME[7:0] R/W-1 R/W-0 R/W-1 (1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-10 Unimplemented: Read as ‘0’ bit 9-0 TMODTIME[9:0]: Transition Mode Duration bits(1) Note 1: The value for TMODTIME[9:0] should be less than the SSTIME[9:0] value.  2017-2019 Microchip Technology Inc. DS70005319D-page 555 dsPIC33CH128MP508 FAMILY REGISTER 11-4: DACxCONH: DACx CONTROL HIGH REGISTER U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — R/W-0 R/W-0 TMCB[9:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TMCB[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-10 Unimplemented: Read as ‘0’ bit 9-0 TMCB[9:0]: DACx Leading-Edge Blanking bits These register bits specify the blanking period for the comparator, following changes to the DAC output during Change-of-State (COS), for the input signal selected by the HCFSEL[3:0] bits in Register 11-9. REGISTER 11-5: DACxCONL: DACx CONTROL LOW REGISTER R/W-0 R/W-0 R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0 DACEN IRQM1(1,2) IRQM0(1,2) — — CBE DACOEN FLTREN bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CMPSTAT CMPPOL INSEL2 INSEL1 INSEL0 HYSPOL HYSSEL1 HYSSEL0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 DACEN: Individual DACx Module Enable bit 1 = Enables DACx module 0 = Disables DACx module to reduce power consumption; any pending Slope mode and/or underflow conditions are cleared bit 14-13 IRQM[1:0]: Interrupt Mode select bits(1,2) 11 = Generates an interrupt on either a rising or falling edge detect 10 = Generates an interrupt on a falling edge detect 01 = Generates an interrupt on a rising edge detect 00 = Interrupts are disabled bit 12-11 Unimplemented: Read as ‘0’ Note 1: 2: Changing these bits during operation may generate a spurious interrupt. The edge selection is a post-polarity selection via the CMPPOL bit. DS70005319D-page 556  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 11-5: DACxCONL: DACx CONTROL LOW REGISTER (CONTINUED) bit 10 CBE: Comparator Blank Enable bit 1 = Enables the analog comparator output to be blanked (gated off) during the recovery transition following the completion of a slope operation 0 = Disables the blanking signal to the analog comparator; therefore, the analog comparator output is always active bit 9 DACOEN: DACx Output Buffer Enable bit 1 = DACx analog voltage is connected to the DACOUT1 pin 0 = DACx analog voltage is not connected to the DACOUT1 pin bit 8 FLTREN: Comparator Digital Filter Enable bit 1 = Digital filter is enabled 0 = Digital filter is disabled bit 7 CMPSTAT: Comparator Status bits The current state of the comparator output including the CMPPOL selection. bit 6 CMPPOL: Comparator Output Polarity Control bit 1 = Output is inverted 0 = Output is noninverted bit 5-3 INSEL[2:0]: Comparator Input Source Select bits Master 111 = Reserved 110 = Reserved 101 = SPGA2 output 100 = SPGA1 output 011 = CMPxD input pin 010 = SPGA3 output 001 = CMPxB input pin 000 = CMPxA input pin Slave 111 = Reserved 110 = Reserved 101 = SPGA2 output 100 = SPGA1 output 011 = S1CMPxD input pin 010 = SPGA3 output 001 = S1CMPxB input pin 000 = S1CMPxA input pin bit 2 HYSPOL: Comparator Hysteresis Polarity Select bit 1 = Hysteresis is applied to the falling edge of the comparator output 0 = Hysteresis is applied to the rising edge of the comparator output bit 1-0 HYSSEL[1:0]: Comparator Hysteresis Select bits 11 = 45 mv hysteresis 10 = 30 mv hysteresis 01 = 15 mv hysteresis 00 = No hysteresis is selected Note 1: 2: Changing these bits during operation may generate a spurious interrupt. The edge selection is a post-polarity selection via the CMPPOL bit.  2017-2019 Microchip Technology Inc. DS70005319D-page 557 dsPIC33CH128MP508 FAMILY REGISTER 11-6: DACxDATH: DACx DATA HIGH REGISTER U-0 U-0 U-0 U-0 — — — — R/W-0 R/W-0 R/W-0 R/W-0 DACDAT[11:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DACDAT[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-12 Unimplemented: Read as ‘0’ bit 11-0 DACDAT[11:0]: DACx Data bits This register specifies the high DACx data value. Valid values are from 205 to 3890. REGISTER 11-7: DACxDATL: DACx DATA LOW REGISTER U-0 U-0 U-0 U-0 — — — — R/W-0 R/W-0 R/W-0 R/W-0 DACLOW[11:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DACLOW[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-12 Unimplemented: Read as ‘0’ bit 11-0 DACLOW[11:0]: DACx Low Data bits In Hysteretic mode, Slope Generator mode and Triangle mode, this register specifies the low data value and/or limit for the DACx module. Valid values are from 205 to 3890. DS70005319D-page 558  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 11-8: SLPxCONH: DACx SLOPE CONTROL HIGH REGISTER R/W-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 U-0 SLOPEN — — — HME(1) TWME(2) PSE — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 SLOPEN: Slope Function Enable/On bit 1 = Enables slope function 0 = Disables slope function; slope accumulator is disabled to reduce power consumption bit 14-12 Unimplemented: Read as ‘0’ bit 11 HME: Hysteretic Mode Enable bit(1) 1 = Enables Hysteretic mode for DACx 0 = Disables Hysteretic mode for DACx bit 10 TWME: Triangle Wave Mode Enable bit(2) 1 = Enables Triangle Wave mode for DACx 0 = Disables Triangle Wave mode for DACx bit 9 PSE: Positive Slope Mode Enable bit 1 = Slope mode is positive (increasing) 0 = Slope mode is negative (decreasing) bit 8-0 Unimplemented: Read as ‘0’ Note 1: 2: HME mode requires the user to disable the slope function (SLOPEN = 0). TWME mode requires the user to enable the slope function (SLOPEN = 1).  2017-2019 Microchip Technology Inc. DS70005319D-page 559 dsPIC33CH128MP508 FAMILY REGISTER 11-9: SLPxCONL: DACx SLOPE CONTROL LOW REGISTER R/W-0 R/W-0 R/W-0 R/W-0 HCFSEL3 HCFSEL2 HCFSEL1 HCFSEL0 R/W-0 R/W-0 R/W-0 R/W-0 SLPSTOPA3 SLPSTOPA2 SLPSTOPA1 SLPSTOPA0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 SLPSTOPB3 SLPSTOPB2 SLPSTOPB1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SLPSTOPB0 SLPSTRT3 SLPSTRT2 SLPSTRT1 SLPSTRT0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set0 ‘0’ = Bit is cleared bit 15-12 HCFSEL[3:0]: Hysteretic Comparator Function Input Select bits The selected input signal controls the switching between the DACx high limit (DACxDATH) and the DACx low limit (DACxDATL) as the data source for the PDM DAC. It modifies the polarity of the comparator, and the rising and falling edges initiate the start of the LEB counter (TMCB[9:0] bits in Register 11-4). Input Selection Master 1111 1 1 1100 0 PWM4H 1011 0 PWM3H 1010 0 PWM2H Slave 1001 0 PWM1H 1000 S1PWM4H S1PWM8H 0111 S1PWM3H S1PWM7H 0110 S1PWM2H S1PWM6H 0101 S1PWM1H S1PWM5H 0100 PWM4H S1PWM4H 0011 PWM3H S1PWM3H 0010 PWM2H S1PWM2H 0001 PWM1H S1PWM1H 0000 0 0 DS70005319D-page 560  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 11-9: bit 11-8 SLPxCONL: DACx SLOPE CONTROL LOW REGISTER (CONTINUED) SLPSTOPA[3:0]: Slope Stop A Signal Select bits The selected Slope Stop A signal is logically OR’d with the selected Slope Stop B signal to terminate the slope function. Slope Stop A Signal Selection bit 7-4 bit 3-0 Master Slave 1111 1 1 1110 Slave PWM2 Trigger 2 Master PWM2 Trigger 2 1101 Slave PWM1 Trigger 2 Master PWM1 Trigger 2 1000 Master PWM4 Trigger 2 Slave PWM8 Trigger 2 0111 Master PWM3 Trigger 2 Slave PWM7 Trigger 2 0110 Master PWM2 Trigger 2 Slave PWM6 Trigger 2 0101 Master PWM1 Trigger 2 Slave PWM5 Trigger 2 0100 Master PWM4 Trigger 1 Slave PWM4 Trigger 2 0011 Master PWM3 Trigger 1 Slave PWM3 Trigger 2 0010 Master PWM2 Trigger 1 Slave PWM2 Trigger 2 0001 Master PWM1 Trigger 1 Slave PWM1 Trigger 2 0000 0 0 SLPSTOPB[3:0]: Slope Stop B Signal Select bits The selected Slope Stop B signal is logically OR’d with the selected Slope Stop A signal to terminate the slope function. Slope Start B Signal Selection Master Slave 1111 1 1 0100 S1CMP3 Out CMP1 Out 0011 S1CMP2 Out S1CMP3 Out 0010 S1CMP1 Out S1CMP2 Out 0001 CMP1 Out S1CMP1 Out 0000 0 0 SLPSTRT[3:0]: Slope Start Signal Select bits Slope Start Signal Selection Master Slave 1111 1 1 1110 Slave PWM2 Trigger 1 Master PWM2 Trigger 1 1101 Slave PWM1 Trigger 1 Master PWM1 Trigger 1 1000 Master PWM4 Trigger 2 Slave PWM8 Trigger 1 0111 Master PWM3 Trigger 2 Slave PWM7 Trigger 1 0110 Master PWM2 Trigger 2 Slave PWM6 Trigger 1 0101 Master PWM1 Trigger 2 Slave PWM5 Trigger 1 0100 Master PWM4 Trigger 1 Slave PWM4 Trigger 1 0011 Master PWM3 Trigger 1 Slave PWM3 Trigger 1 0010 Master PWM2 Trigger 1 Slave PWM2 Trigger 1 0001 Master PWM1 Trigger 1 Slave PWM1 Trigger 1 0000 0 0  2017-2019 Microchip Technology Inc. DS70005319D-page 561 dsPIC33CH128MP508 FAMILY REGISTER 11-10: SLPxDAT: DACx SLOPE DATA REGISTER(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SLPDAT[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SLPDAT[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Note 1: SLPDAT[15:0]: Slope Ramp Rate Value bits The SLPDATx value is in 12.4 format. Register data are left justified. DS70005319D-page 562  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 12.0 QUADRATURE ENCODER INTERFACE (QEI) (MASTER/SLAVE) Typically, three output channels, Phase A (QEAx), Phase B (QEBx) and Index (INDXx), provide information on the movement of the motor shaft, including distance and direction. Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive resource. For more information, refer to the “Quadrature Encoder Interface (QEI)” (www.microchip.com/DS70000601) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). The two channels, Phase A (QEAx) and Phase B (QEBx), are typically 90 degrees out of phase with respect to each other. The Phase A and Phase B channels have a unique relationship. If Phase A leads Phase B, the direction of the motor is deemed positive or forward. If Phase A lags Phase B, the direction of the motor is deemed negative or reverse. The Index pulse occurs once per mechanical revolution and is used as a reference to indicate an absolute position. Figure 12-1 illustrates the Quadrature Encoder Interface signals. 2: The QEI is identical for both Master core and Slave core (the x represents the number of the specific module being addressed in Master or Slave). The Quadrature signals from the encoder can have four unique states (‘01’, ‘00’, ‘10’ and ‘11’) that reflect the relationship between QEAx and QEBx. Figure 12-1 illustrates these states for one count cycle. The order of the states get reversed when the direction of travel changes. 3: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 3.2 “Master Memory Organization” in this data sheet for device-specific register and bit information. The Quadrature Decoder increments or decrements the 32-bit up/down Position x Counter (POSxCNTH/L) registers for each Change-of-State (COS). The counter increments when QEAx leads QEBx and decrements when QEBx leads QEAx. Table 12-1 shows an overview of the QEI module. The Quadrature Encoder Interface (QEI) module provides the interface to incremental encoders for obtaining mechanical position data. Quadrature Encoders, also known as incremental encoders or optical encoders, detect position and speed of rotating motion systems. Quadrature Encoders enable closed-loop control of motor control applications, such as Switched Reluctance (SR) and AC Induction Motors (ACIM). TABLE 12-1: A typical Quadrature Encoder includes a slotted wheel attached to the shaft of the motor and an emitter/ detector module that senses the slots in the wheel. FIGURE 12-1: QEI MODULE OVERVIEW Number of QEI Modules Identical (Modules) Master Core 1 Yes Slave Core 1 Yes QUADRATURE ENCODER INTERFACE SIGNALS QEAx QEBx POSxCNT +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 Up/Down  2017-2019 Microchip Technology Inc. DS70005319D-page 563 dsPIC33CH128MP508 FAMILY Table 12-2 shows the truth table that describes how the Quadrature signals are decoded. TABLE 12-2: TRUTH TABLE FOR QUADRATURE ENCODER Current Previous Quadrature Quadrature State State Action QA QB QA QB 1 1 1 1 No count or direction change 1 1 1 0 Count up 1 1 0 1 Count down 1 1 0 0 Invalid state change; ignore 1 0 1 1 Count down 1 0 1 0 No count or direction change 1 0 0 1 Invalid state change; ignore 1 0 0 0 Count up 0 1 1 1 Count up 0 1 1 0 Invalid state change; ignore 0 1 0 1 No count or direction change 0 1 0 0 Count down 0 0 1 1 Invalid state change; ignore 0 0 1 0 Count down 0 0 0 1 Count up 0 0 0 0 No count or direction change The QEI module consists of the following major features: • Four Input Pins: Two Phase Signals, an Index Pulse and a Home Pulse • Programmable Digital Noise Filters on Inputs • Quadrature Decoder providing Counter Pulses and Count Direction • Count Direction Status • 4x Count Resolution • Index (INDXx) Pulse to Reset the Position Counter • General Purpose 32-Bit Timer/Counter mode • Interrupts generated by QEI or Counter Events • 32-Bit Velocity Counter • 32-Bit Position Counter • 32-Bit Index Pulse Counter • 32-Bit Interval Timer • 32-Bit Position Initialization/Capture Register • 32-Bit Compare Less Than and Greater Than Registers • External Up/Down Count mode • External Gated Count mode • External Gated Timer mode • Interval Timer mode Figure 12-2 illustrates the simplified block diagram of the QEI module. The QEI module consists of decoder logic to interpret the Phase A (QEAx) and Phase B (QEBx) signals, and an up/down counter to accumulate the count. The counter pulses are generated when the Quadrature state changes. The count direction information must be maintained in a register until a direction change is detected. The module also includes digital noise filters, which condition the input signal. DS70005319D-page 564  2017-2019 Microchip Technology Inc.  2017-2019 Microchip Technology Inc. FIGURE 12-2: QUADRATURE ENCODER INTERFACE (QEI) MODULE BLOCK DIAGRAM FLTREN GATEN HOMEx FHOMEx DIR_GATE  QFDIV PBCLK FINDXx INDXx COUNT 1 EXTCNT DIVCLK 0 Digital Filter COUNT_EN CCM[1:0] Quadrature Decoder Logic QEBx COUNT DIR DIR DIR_GATE CNT_DIR 0 CNTPOL EXTCNT DIR_GATE PCHGE PCLLE CCMPx PCLLE Comparator PCHGE PCHEQ PCLEQ Comparator PCLLE PCHGE OUTFNC[1:0] PBCLK  INTDIV DIVCLK COUNT_EN CNT_DIR FINDXx CNT_DIR Index Counter Register (INDXxCNT) DS70005319D-page 565 Index Counter Hold Register (INDXxHLD) Interval Timer Register (INTxTMR) Interval Timer Hold Register (INTxHLD) COUNT_EN Velocity Counter Register (VELxCNT) Velocity Counter Hold Register (VELxHLD) Greater Than or Equal Compare Register (QEIxGEC)(1) Less Than or Equal Compare Register (QEIxLEC) COUNT_EN CNT_DIR Position Counter Register (POSxCNT) Position Counter Hold Register (POSxHLD) Data Bus Note 1: These registers map to the same memory location. 2: Shaded registers are not used in 32-bit devices. They are provided to maintain uniformity with 16-bit architecture. QCAPEN Data Bus Initialization and Capture Register (QEIxIC)(1) dsPIC33CH128MP508 FAMILY QEAx dsPIC33CH128MP508 FAMILY 12.1 QEI Control and Status Registers REGISTER 12-1: QEIxCON: QEIx CONTROL REGISTER R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 QEIEN — QEISIDL PIMOD2 PIMOD1 PIMOD0 IMV1 IMV0 bit 15 bit 8 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — INTDIV2 INTDIV1 INTDIV0 CNTPOL GATEN CCM1 CCM0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 QEIEN: Quadrature Encoder Interface Module Enable bit 1 = QEI module is enabled 0 = QEI module is disabled; however, SFRs can be read or written bit 14 Unimplemented: Read as ‘0’ bit 13 QEISIDL: QEI Stop in Idle Mode bit 1 = Discontinues module operation when device enters Idle mode 0 = Continues module operation in Idle mode bit 12-10 PIMOD[2:0]: Position Counter Initialization Mode Select bits 111 = Modulo Count mode for position counter and every Index event resets the position counter 110 = Modulo Count mode for position counter 101 = Resets the position counter when the position counter equals the QEIxGEC register 100 = Second Index event after Home event initializes the position counter with the contents of the QEIxIC register 011 = First Index event after Home event initializes the position counter with the contents of the QEIxIC register 010 = Next Index input event initializes the position counter with the contents of the QEIxIC register 001 = Every Index input event resets the position counter 000 = Index input event does not affect the position counter bit 9-8 IMV[1:0]: Index Match Value bits 11 = Index match occurs when QEBx = 1 and QEAx = 1 10 = Index match occurs when QEBx = 1 and QEAx = 0 01 = Index match occurs when QEBx = 0 and QEAx = 1 00 = Index match occurs when QEBx = 0 and QEAx = 0 bit 7 Unimplemented: Read as ‘0’ bit 6-4 INTDIV[2:0]: Timer Input Clock Prescale Select bits (interval timer, main timer (position counter), velocity counter and Index counter internal clock divider select) 111 = 1:128 prescale value 110 = 1:64 prescale value 101 = 1:32 prescale value 100 = 1:16 prescale value 011 = 1:8 prescale value 010 = 1:4 prescale value 001 = 1:2 prescale value 000 = 1:1 prescale value bit 3 CNTPOL: Position, Velocity and Index Counter/Timer Direction Select bit 1 = Counter direction is negative unless modified by an external up/down signal 0 = Counter direction is positive unless modified by an external up/down signal DS70005319D-page 566  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 12-1: QEIxCON: QEIx CONTROL REGISTER (CONTINUED) bit 2 GATEN: External Count Gate Enable bit 1 = External gate signal controls the position counter/timer operation 0 = External gate signal does not affect the position counter/timer operation bit 1-0 CCM[1:0]: Counter Control Mode Selection bits 11 = Internal timer with External Gate mode 10 = External Clock count with External Gate mode 01 = External Clock count with External Up/Down mode 00 = Quadrature Encoder mode REGISTER 12-2: QEIxIOCL: QEIx I/O CONTROL LOW REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 QCAPEN FLTREN QFDIV2 QFDIV1 QFDIV0 OUTFNC1 OUTFNC0 SWPAB bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R-x R-x R-x R-x HOMPOL IDXPOL QEBPOL QEAPOL HOME INDEX QEB QEA bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 QCAPEN: QEIx Position Counter Input Capture by Index Event Enable bit 1 = Index match event (positive edge) triggers a position capture event 0 = Index match event (positive edge) does not trigger a position capture event bit 14 FLTREN: QEAx/QEBx/INDXx/HOMEx Digital Filter Enable bit 1 = Input pin digital filter is enabled 0 = Input pin digital filter is disabled (bypassed) bit 13-11 QFDIV[2:0]: QEAx/QEBx/INDXx/HOMEx Digital Input Filter Clock Divide Select bits 111 = 1:128 clock divide 110 = 1:64 clock divide 101 = 1:32 clock divide 100 = 1:16 clock divide 011 = 1:8 clock divide 010 = 1:4 clock divide 001 = 1:2 clock divide 000 = 1:1 clock divide bit 10-9 OUTFNC[1:0]: QEIx Module Output Function Mode Select bits 11 = The QEICMP pin goes high when POSxCNT < QEIxLEC or POSxCNT > QEIxGEC 10 = The QEICMP pin goes high when POSxCNT < QEIxLEC 01 = The QEICMP pin goes high when POSxCNT > QEIxGEC 00 = Output is disabled bit 8 SWPAB: Swap QEAx and QEBx Inputs bit 1 = QEAx and QEBx are swapped prior to Quadrature Decoder logic 0 = QEAx and QEBx are not swapped bit 7 HOMPOL: HOMEx Input Polarity Select bit 1 = Input is inverted 0 = Input is not inverted  2017-2019 Microchip Technology Inc. DS70005319D-page 567 dsPIC33CH128MP508 FAMILY REGISTER 12-2: QEIxIOCL: QEIx I/O CONTROL LOW REGISTER (CONTINUED) bit 6 IDXPOL: INDXx Input Polarity Select bit 1 = Input is inverted 0 = Input is not inverted bit 5 QEBPOL: QEBx Input Polarity Select bit 1 = Input is inverted 0 = Input is not inverted bit 4 QEAPOL: QEAx Input Polarity Select bit 1 = Input is inverted 0 = Input is not inverted bit 3 HOME: Status of HOMEx Input Pin after Polarity Control bit (read-only) 1 = Pin is at logic ‘1’ if the HOMPOL bit is set to ‘0’; pin is at logic ‘0’ if the HOMPOL bit is set to ‘1’ 0 = Pin is at logic ‘0’ if the HOMPOL bit is set to ‘0’; pin is at logic ‘1’ if the HOMPOL bit is set to ‘1’ bit 2 INDEX: Status of INDXx Input Pin After Polarity Control bit (read-only) 1 = Pin is at logic ‘1’ if the IDXPOL bit is set to ‘0’; pin is at logic ‘0’ if the IDXPOL bit is set to ‘1’ 0 = Pin is at logic ‘0’ if the IDXPOL bit is set to ‘0’; pin is at logic ‘1’ if the IDXPOL bit is set to ‘1’ bit 1 QEB: Status of QEBx Input Pin After Polarity Control and SWPAB Pin Swapping bit (read-only) 1 = Physical pin, QEBx, is at logic ‘1’ if the QEBPOL bit is set to ‘0’ and the SWPAB bit is set to ‘0’; physical pin, QEBx, is at logic ‘0’ if the QEBPOL bit is set to ‘1’ and the SWPAB bit is set to ‘0’; physical pin, QEAx, is at logic ‘1’ if the QEBPOL bit is set to ‘0’ and the SWPAB bit is set to ‘1’; physical pin, QEAx, is at logic ‘0’ if the QEBPOL bit is set to ‘1’ and the SWPAB bit is set to ‘1’ 0 = Physical pin, QEBx, is at logic ‘0’ if the QEBPOL bit is set to ‘0’ and the SWPAB bit is set to ‘0’; physical pin, QEBx, is at logic ‘1’ if the QEBPOL bit is set to ‘1’ and the SWPAB bit is set to ‘0’; physical pin, QEAx, is at logic ‘0’ if the QEBPOL bit is set to ‘0’ and the SWPAB bit is set to ‘1’; physical pin, QEAx, is at logic ‘1’ if the QEBPOL bit is set to ‘1’ and the SWPAB bit is set to ‘1’ bit 0 QEA: Status of QEAx Input Pin After Polarity Control and SWPAB Pin Swapping bit (read-only) 1 = Physical pin, QEAx, is at logic ‘1’ if the QEAPOL bit is set to ‘0’ and the SWPAB bit is set to ‘0’; physical pin, QEAx, is at logic ‘0’ if the QEAPOL bit is set to ‘1’ and the SWPAB bit is set to ‘0’; physical pin, QEBx, is at logic ‘1’ if the QEAPOL bit is set to ‘0’ and the SWPAB bit is set to ‘1’; physical pin, QEBx, is at logic ‘0’ if the QEAPOL bit is set to ‘1’ and the SWPAB bit is set to ‘1’ 0 = Physical pin, QEAx, is at logic ‘0’ if the QEAPOL bit is set to ‘0’ and the SWPAB bit is set to ‘0’; physical pin, QEAx, is at logic ‘1’ if the QEAPOL bit is set to ‘1’ and the SWPAB bit is set to ‘0’; physical pin, QEBx, is at logic ‘0’ if the QEAPOL bit is set to ‘0’ and the SWPAB bit is set to ‘1’ DS70005319D-page 568  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 12-3: QEIxIOCH: QEIx I/O CONTROL HIGH REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — — HCAPEN bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-1 Unimplemented: Read as ‘0’ bit 0 HCAPEN: Position Counter Input Capture by Home Event Enable bit 1 = HOMEx input event (positive edge) triggers a position capture event 0 = HOMEx input event (positive edge) does not trigger a position capture event  2017-2019 Microchip Technology Inc. DS70005319D-page 569 dsPIC33CH128MP508 FAMILY REGISTER 12-4: QEIxSTAT: QEIx STATUS REGISTER U-0 U-0 HS/R/C-0 R/W-0 HS/R/C-0 R/W-0 HS/R/C-0 R/W-0 — — PCHEQIRQ PCHEQIEN PCLEQIRQ PCLEQIEN POSOVIRQ POSOVIEN bit 15 bit 8 HS/R/C-0 R/W-0 HS/R/C-0 R/W-0 HS/R/C-0 R/W-0 HS/R/C-0 R/W-0 PCIIRQ(1) PCIIEN VELOVIRQ VELOVIEN HOMIRQ HOMIEN IDXIRQ IDXIEN bit 7 bit 0 Legend: C = Clearable bit HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 PCHEQIRQ: Position Counter Greater Than Compare Status bit 1 = POSxCNT  QEIxGEC 0 = POSxCNT < QEIxGEC bit 12 PCHEQIEN: Position Counter Greater Than Compare Interrupt Enable bit 1 = Interrupt is enabled 0 = Interrupt is disabled bit 11 PCLEQIRQ: Position Counter Less Than Compare Status bit 1 = POSxCNT  QEIxLEC 0 = POSxCNT > QEIxLEC bit 10 PCLEQIEN: Position Counter Less Than Compare Interrupt Enable bit 1 = Interrupt is enabled 0 = Interrupt is disabled bit 9 POSOVIRQ: Position Counter Overflow Status bit 1 = Overflow has occurred 0 = No overflow has occurred bit 8 POSOVIEN: Position Counter Overflow Interrupt Enable bit 1 = Interrupt is enabled 0 = Interrupt is disabled bit 7 PCIIRQ: Position Counter (Homing) Initialization Process Complete Status bit(1) 1 = POSxCNT was reinitialized 0 = POSxCNT was not reinitialized bit 6 PCIIEN: Position Counter (Homing) Initialization Process Complete Interrupt Enable bit 1 = Interrupt is enabled 0 = Interrupt is disabled bit 5 VELOVIRQ: Velocity Counter Overflow Status bit 1 = Overflow has occurred 0 = No overflow has occurred bit 4 VELOVIEN: Velocity Counter Overflow Interrupt Enable bit 1 = Interrupt is enabled 0 = Interrupt is disabled bit 3 HOMIRQ: Status Flag for Home Event Status bit 1 = Home event has occurred 0 = No Home event has occurred Note 1: This status bit is only applicable to PIMOD[2:0] modes, ‘011’ and ‘100’. DS70005319D-page 570  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 12-4: QEIxSTAT: QEIx STATUS REGISTER (CONTINUED) bit 2 HOMIEN: Home Input Event Interrupt Enable bit 1 = Interrupt is enabled 0 = Interrupt is disabled bit 1 IDXIRQ: Status Flag for Index Event Status bit 1 = Index event has occurred 0 = No Index event has occurred bit 0 IDXIEN: Index Input Event Interrupt Enable bit 1 = Interrupt is enabled 0 = Interrupt is disabled Note 1: This status bit is only applicable to PIMOD[2:0] modes, ‘011’ and ‘100’. REGISTER 12-5: R/W-0 POSxCNTL: POSITION x COUNTER REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 POSCNT[15:8] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 POSCNT[7:0] R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown POSCNT[15:0]: Position Counter Value bits REGISTER 12-6: R/W-0 POSxCNTH: POSITION x COUNTER REGISTER HIGH R/W-0 R/W-0 R/W-0 R/W-0 POSCNT[31:24] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 POSCNT[23:16] R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown POSCNT[31:16]: Position Counter Value bits  2017-2019 Microchip Technology Inc. DS70005319D-page 571 dsPIC33CH128MP508 FAMILY REGISTER 12-7: R/W-0 POSxHLDL: POSITION x COUNTER HOLD REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 POSHLD[15:8] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 POSHLD[7:0] R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown POSHLD[15:0]: Position Counter Hold for Reading/Writing Position x Counter Register (POSxCNT) bits REGISTER 12-8: R/W-0 POSxHLDH: POSITION x COUNTER HOLD REGISTER HIGH R/W-0 R/W-0 R/W-0 R/W-0 POSHLD[31:24] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 POSHLD[23:16] R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown POSHLD[31:16]: Position Counter Hold for Reading/Writing Position x Counter Register (POSxCNT) bits DS70005319D-page 572  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 12-9: R/W-0 VELxCNTL: VELOCITY x COUNTER REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 VELCNT[15:8] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 VELCNT[7:0] R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown VELCNT[15:0]: Velocity Counter Value bits REGISTER 12-10: VELxCNTH: VELOCITY x COUNTER REGISTER HIGH R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 VELCNT[31:24] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 VELCNT[23:16] R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown VELCNT[31:16]: Velocity Counter Value bits  2017-2019 Microchip Technology Inc. DS70005319D-page 573 dsPIC33CH128MP508 FAMILY REGISTER 12-11: VELxHLDL: VELOCITY x COUNTER HOLD REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 VELHLD[15:8] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 VELHLD[7:0] R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown VELHLD[15:0]: Velocity Counter Hold Value bits REGISTER 12-12: VELxHLDH: VELOCITY x COUNTER HOLD REGISTER HIGH R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 VELHLD[31:24] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 VELHLD[23:16] R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown VELHLD[31:16]: Velocity Counter Hold Value bits DS70005319D-page 574  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 12-13: INTxTMRL: INTERVAL x TIMER REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INTTMR[15:8] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INTTMR[7:0] R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown INTTMR[15:0]: Interval Timer Value bits REGISTER 12-14: INTxTMRH: INTERVAL x TIMER REGISTER HIGH R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INTTMR[31:24] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INTTMR[23:16] R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown INTTMR[31:16]: Interval Timer Value bits  2017-2019 Microchip Technology Inc. DS70005319D-page 575 dsPIC33CH128MP508 FAMILY REGISTER 12-15: INTXxHLDL: INDEX x COUNTER HOLD REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INTHLD[15:8] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INTHLD[7:0] R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown INTXHLD[15:0]: Hold for Reading/Writing Interval Timer Value Register (INDXCNT) bits REGISTER 12-16: INTXxHLDH: INDEX x COUNTER HOLD REGISTER HIGH R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INTHLD[31:24] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INTHLD[23:16] R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown INTHLD[31:16]: Hold for Reading/Writing Interval Timer Value Register (INDXCNT) bits DS70005319D-page 576  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 12-17: INDXxCNTL: INDEX x COUNTER REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INDXCNT[15:8] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INDXCNT[7:0] R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown INDXCNT[15:0]: Index Counter Value bits REGISTER 12-18: INDXxCNTH: INDEX x COUNTER REGISTER HIGH R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INDXCNT[31:24] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INDXCNT[23:16] R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown INDXCNT[31:16]: Index Counter Value bits  2017-2019 Microchip Technology Inc. DS70005319D-page 577 dsPIC33CH128MP508 FAMILY REGISTER 12-19: INDXxHLDL: INDEX x COUNTER HOLD REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INDXHLD[15:8] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INDXHLD[7:0] R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown INDXHLD[15:0]: Hold for Reading/Writing Index x Counter Register (INDXCNT) bits REGISTER 12-20: INDXxHLDH: INDEX x COUNTER HOLD REGISTER HIGH R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INDXHLD[31:24] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INDXHLD[23:16] R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown INDXHLD[31:16]: Hold for Reading/Writing Index x Counter Register (INDXCNT) bits DS70005319D-page 578  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 12-21: QEIxGECL: QEIx GREATER THAN OR EQUAL COMPARE REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 QEIGEC[15:8] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 QEIGEC[7:0] R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown QEIGEC[15:0]: QEIx Greater Than or Equal Compare bits REGISTER 12-22: QEIxGECH: QEIx GREATER THAN OR EQUAL COMPARE REGISTER HIGH R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 QEIGEC[31:24] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 QEIGEC[23:16] R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown QEIGEC[31:16]: QEIx Greater Than or Equal Compare bits  2017-2019 Microchip Technology Inc. DS70005319D-page 579 dsPIC33CH128MP508 FAMILY REGISTER 12-23: QEIxLECL: QEIx LESS THAN OR EQUAL COMPARE REGISTER LOW R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 QEIIC[31:24] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 QEIIC[23:16] R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown QEIIC[31:16]: QEIx Less Than or Equal Compare bits REGISTER 12-24: QEIxLECH: QEIx LESS THAN OR EQUAL COMPARE REGISTER HIGH R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 QEIIC[15:8] R/W-0 R/W-0 R/W-0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 QEIIC[7:0] R/W-0 R/W-0 R/W-0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown QEIIC[15:0]: QEIx Less Than or Equal Compare bits DS70005319D-page 580  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 13.0 UNIVERSAL ASYNCHRONOUS RECEIVER TRANSMITTER (UART) Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “Multiprotocol Universal Asynchronous Receiver Transmitter (UART) Module” (www.microchip.com/DS70005288) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). 2: The UART is identical for both Master core and Slave core. The x is common for both Master core and Slave core (where the x represents the number of the specific module being addressed). The number of UART modules available on the Master core and Slave core is different and they are located in different SFR locations. 3: All associated register names are the same on the Master core and the Slave core. The Slave code will be developed in a separate project in MPLAB® X IDE with the device selection, dsPIC33CH128MP508S1, where the S1 indicates the Slave device. The Master UART is UART1 and UART2, and the Slave UART is UART1. The Universal Asynchronous Receiver Transmitter (UART) is a flexible serial communication peripheral used to interface dsPIC® microcontrollers with other equipment, including computers and peripherals. The UART is a full-duplex, asynchronous communication channel that can be used to implement protocols, such as RS-232 and RS-485. The UART also supports the following hardware extensions: • LIN/J2602 • Direct Matrix Architecture (DMX) • Smart Card The primary features of the UART are: • Full or Half-Duplex Operation • Up to 8-Deep TX and RX First In, First Out (FIFO) Buffers • 8-Bit or 9-Bit Data Width • Configurable Stop Bit Length • Flow Control • Auto-Baud Calibration • Parity, Framing and Buffer Overrun Error Detection • Address Detect • Break Transmission • Transmit and Receive Polarity Control • Manchester Encoder/Decoder • Operation in Sleep mode • Wake from Sleep on Sync Break Received Interrupt Table 13-1 shows an overview of the module. TABLE 13-1: UART MODULE OVERVIEW Number of UART Modules Identical (Modules) Master Core 2 Yes Slave Core 1 Yes  2017-2019 Microchip Technology Inc. DS70005319D-page 581 dsPIC33CH128MP508 FAMILY 13.1 Architectural Overview The UART transfers bytes of data, to and from device pins, using First-In First-Out (FIFO) buffers up to eight bytes deep. The status of the buffers and data is made available to user software through Special Function FIGURE 13-1: Registers (SFRs). The UART implements multiple interrupt channels for handling transmit, receive and error events. A simplified block diagram of the UART is shown in Figure 13-1. SIMPLIFIED UARTx BLOCK DIAGRAM Clock Inputs Baud Rate Generator Data Bus SFRs Interrupts Interrupt Generation TX Buffer, UxTXREG TX RX Buffer, UxRXREG RX UxDSR UxRTS Hardware Flow Control Error and Event Detection DS70005319D-page 582 UxCTS UxDTR  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 13.2 Character Frame A typical UART character frame is shown in Figure 13-2. The Idle state is high with a ‘Start’ condition indicated by a falling edge. The Start bit is followed by the number of data, parity/address detect and Stop bits defined by the MOD[3:0] (UxMODE[3:0]) bits selected. FIGURE 13-2: UART CHARACTER FRAME Idle Idle Start Bit 13.3 D0 D1 D2 D3 Data Buffers Both transmit and receive functions use buffers to store data shifted to/from the pins. These buffers are FIFOs and are accessed by reading the SFRs, UxTXREG and UxRXREG, respectively. Each data buffer has multiple flags associated with its operation to allow software to read the status. Interrupts can also be configured based on the space available in the buffers. The transmit and receive buffers can be cleared and their pointers reset using the associated TX/RX Buffer Empty Status bits, UTXBE (UxSTAH[5]) and URXBE (UxSTAH[1]).  2017-2019 Microchip Technology Inc. D4 D5 D6 13.4 D7 Parity/ Address Stop Detect Bit(s) Protocol Extensions The UART provides hardware support for LIN/J2602, DMX and smart card protocol extensions to reduce software overhead. A protocol extension is enabled by writing a value to the MOD[3:0] (UxMODE[3:0]) selection bits and further configured using the UARTx Timing Parameter registers, UxP1 (Register 13-9), UxP2 (Register 13-10), UxP3 (Register 13-11) and UxP3H (Register 13-12). Details regarding operation and usage are discussed in their respective chapters. Not all protocols are available on all devices. DS70005319D-page 583 dsPIC33CH128MP508 FAMILY 13.5 UART Control/Status Registers REGISTER 13-1: UxMODE: UARTx CONFIGURATION REGISTER R/W-0 U-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 HC/R/W-0(1) UARTEN — USIDL WAKE RXBIMD — BRKOVR UTXBRK bit 15 bit 8 R/W-0 HC/R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 BRGH ABAUD UTXEN URXEN MOD3 MOD2 MOD1 MOD0 bit 7 bit 0 Legend: HC = Hardware Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 UARTEN: UART Enable bit 1 = UART is ready to transmit and receive 0 = UART state machine, FIFO Buffer Pointers and counters are reset; registers are readable and writable bit 14 Unimplemented: Read as ‘0’ bit 13 USIDL: UART Stop in Idle Mode bit 1 = Discontinues module operation when device enters Idle mode 0 = Continues module operation in Idle mode bit 12 WAKE: Wake-up Enable bit 1 = Module will continue to sample the RX pin – interrupt generated on falling edge, bit cleared in hardware on following rising edge; if ABAUD is set, Auto-Baud Detection (ABD) will begin immediately 0 = RX pin is not monitored nor rising edge detected bit 11 RXBIMD: Receive Break Interrupt Mode bit 1 = RXBKIF flag when a minimum of 23 (DMX)/11 (asynchronous or LIN/J2602) low bit periods are detected 0 = RXBKIF flag when the Break makes a low-to-high transition after being low for at least 23/11 bit periods bit 10 Unimplemented: Read as ‘0’ bit 9 BRKOVR: Send Break Software Override bit Overrides the TX Data Line: 1 = Makes the TX line active (Output 0 when UTXINV = 0, Output 1 when UTXINV = 1) 0 = TX line is driven by the shifter bit 8 UTXBRK: UART Transmit Break bit(1) 1 = Sends Sync Break on next transmission; cleared by hardware upon completion 0 = Sync Break transmission is disabled or has completed bit 7 BRGH: High Baud Rate Select bit 1 = High Speed: Baud rate is baudclk/4 0 = Low Speed: Baud rate is baudclk/16 bit 6 ABAUD: Auto-Baud Detect Enable bit (read-only when MOD[3:0] = 1xxx) 1 = Enables baud rate measurement on the next character – requires reception of a Sync field (55h); cleared in hardware upon completion 0 = Baud rate measurement is disabled or has completed Note 1: 2: R/HS/HC in DMX and LIN mode. These modes are not available on all devices. DS70005319D-page 584  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 13-1: UxMODE: UARTx CONFIGURATION REGISTER (CONTINUED) bit 5 UTXEN: UART Transmit Enable bit 1 = Transmit enabled – except during Auto-Baud Detection 0 = Transmit disabled – all transmit counters, pointers and state machines are reset; TX buffer is not flushed, status bits are not reset bit 4 URXEN: UART Receive Enable bit 1 = Receive enabled – except during Auto-Baud Detection 0 = Receive disabled – all receive counters, pointers and state machines are reset; RX buffer is not flushed, status bits are not reset bit 3-0 MOD[3:0]: UART Mode bits Other = Reserved 1111 = Smart card(2) 1110 = Reserved 1101 = Reserved 1100 = LIN Master/Slave 1011 = LIN Slave only 1010 = DMX(2) 1001 = Reserved 1000 = Reserved 0111 = Reserved 0110 = Reserved 0101 = Reserved 0100 = Asynchronous 9-bit UART with address detect, ninth bit = 1 signals address 0011 = Asynchronous 8-bit UART without address detect, ninth bit is used as an even parity bit 0010 = Asynchronous 8-bit UART without address detect, ninth bit is used as an odd parity bit 0001 = Asynchronous 7-bit UART 0000 = Asynchronous 8-bit UART Note 1: 2: R/HS/HC in DMX and LIN mode. These modes are not available on all devices.  2017-2019 Microchip Technology Inc. DS70005319D-page 585 dsPIC33CH128MP508 FAMILY REGISTER 13-2: UxMODEH: UARTx CONFIGURATION REGISTER HIGH R/W-0 R-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 SLPEN ACTIVE — — BCLKMOD BCLKSEL1 BCLKSEL0 HALFDPLX bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RUNOVF URXINV STSEL1 STSEL0 C0EN UTXINV FLO1 FLO0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 SLPEN: Run During Sleep Enable bit 1 = UART BRG clock runs during Sleep 0 = UART BRG clock is turned off during Sleep bit 14 ACTIVE: UART Running Status bit 1 = UART clock request is active (user can not update the UxMODE/UxMODEH registers) 0 = UART clock request is not active (user can update the UxMODE/UxMODEH registers) bit 13-12 Unimplemented: Read as ‘0’ bit 11 BCLKMOD: Baud Clock Generation Mode Select bit 1 = Uses fractional Baud Rate Generation 0 = Uses legacy divide-by-x counter for baud clock generation (x = 4 or 16 depending on the BRGH bit) bit 10-9 BCLKSEL[1:0]: Baud Clock Source Selection bits 11 = Reserved 10 = FOSC 01 = Reserved 00 = FOSC/2 (FP) bit 8 HALFDPLX: UART Half-Duplex Selection Mode bit 1 = Half-Duplex mode: UxTX is driven as an output when transmitting and tri-stated when TX is Idle 0 = Full-Duplex mode: UxTX is driven as an output at all times when both UARTEN and UTXEN are set bit 7 RUNOVF: Run During Overflow Condition Mode bit 1 = When an Overflow Error (OERR) condition is detected, the RX shifter continues to run so as to remain synchronized with incoming RX data; data are not transferred to UxRXREG when it is full (i.e., no UxRXREG data are overwritten) 0 = When an Overflow Error (OERR) condition is detected, the RX shifter stops accepting new data (Legacy mode) bit 6 URXINV: UART Receive Polarity bit 1 = Inverts RX polarity; Idle state is low 0 = Input is not inverted; Idle state is high bit 5-4 STSEL[1:0]: Number of Stop Bits Selection bits 11 = 2 Stop bits sent, 1 checked at receive 10 = 2 Stop bits sent, 2 checked at receive 01 = 1.5 Stop bits sent, 1.5 checked at receive 00 = 1 Stop bit sent, 1 checked at receive bit 3 C0EN: Enable Legacy Checksum (C0) Transmit and Receive bit 1 = Checksum Mode 1 (enhanced LIN checksum in LIN mode; add all TX/RX words in all other modes) 0 = Checksum Mode 0 (legacy LIN checksum in LIN mode; not used in all other modes) DS70005319D-page 586  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 13-2: UxMODEH: UARTx CONFIGURATION REGISTER HIGH (CONTINUED) bit 2 UTXINV: UART Transmit Polarity bit 1 = Inverts TX polarity; TX is low in Idle state 0 = Output data are not inverted; TX output is high in Idle state bit 1-0 FLO[1:0]: Flow Control Enable bits (only valid when MOD[3:0] = 0xxx) 11 = Reserved 10 = RTS-DSR (for TX side)/CTS-DTR (for RX side) hardware flow control 01 = XON/XOFF software flow control 00 = Flow control off  2017-2019 Microchip Technology Inc. DS70005319D-page 587 dsPIC33CH128MP508 FAMILY REGISTER 13-3: UxSTA: UARTx STATUS REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TXMTIE PERIE ABDOVE CERIE FERIE RXBKIE OERIE TXCIE bit 15 bit 8 R-1 R-0 HS/R/W-0 HS/R/W-0 R-0 HS/R/W-0 HS/R/W-0 HS/R/W-0 TRMT PERR ABDOVF CERIF FERR RXBKIF OERR TXCIF bit 7 bit 0 Legend: HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 TXMTIE: Transmit Shifter Empty Interrupt Enable bit 1 = Interrupt is enabled 0 = Interrupt is disabled bit 14 PERIE: Parity Error Interrupt Enable bit 1 = Interrupt is enabled 0 = Interrupt is disabled bit 13 ABDOVE: Auto-Baud Rate Acquisition Interrupt Enable bit 1 = Interrupt is enabled 0 = Interrupt is disabled bit 12 CERIE: Checksum Error Interrupt Enable bit 1 = Interrupt is enabled 0 = Interrupt is disabled bit 11 FERIE: Framing Error Interrupt Enable bit 1 = Interrupt is enabled 0 = Interrupt is disabled bit 10 RXBKIE: Receive Break Interrupt Enable bit 1 = Interrupt is enabled 0 = Interrupt is disabled bit 9 OERIE: Receive Buffer Overflow Interrupt Enable bit 1 = Interrupt is enabled 0 = Interrupt is disabled bit 8 TXCIE: Transmit Collision Interrupt Enable bit 1 = Interrupt is enabled 0 = Interrupt is disabled bit 7 TRMT: Transmit Shifter Empty Interrupt Flag bit (read-only) 1 = Transmit Shift Register (TSR) is empty (end of last Stop bit when STPMD = 1 or middle of first Stop bit when STPMD = 0) 0 = Transmit Shift Register is not empty bit 6 PERR: Parity Error/Address Received/Forward Frame Interrupt Flag bit LIN and Parity Modes: 1 = Parity error detected 0 = No parity error detected Address Mode: 1 = Address received 0 = No address detected All Other Modes: Not used. DS70005319D-page 588  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 13-3: UxSTA: UARTx STATUS REGISTER (CONTINUED) bit 5 ABDOVF: Auto-Baud Rate Acquisition Interrupt Flag bit (must be cleared by software) 1 = BRG rolled over during the auto-baud rate acquisition sequence (must be cleared in software) 0 = BRG has not rolled over during the auto-baud rate acquisition sequence bit 4 CERIF: Checksum Error Interrupt Flag bit (must be cleared by software) 1 = Checksum error 0 = No checksum error bit 3 FERR: Framing Error Interrupt Flag bit 1 = Framing Error: Inverted level of the Stop bit corresponding to the topmost character in the buffer; propagates through the buffer with the received character 0 = No framing error bit 2 RXBKIF: Receive Break Interrupt Flag bit (must be cleared by software) 1 = A Break was received 0 = No Break was detected bit 1 OERR: Receive Buffer Overflow Interrupt Flag bit (must be cleared by software) 1 = Receive buffer has overflowed 0 = Receive buffer has not overflowed bit 0 TXCIF: Transmit Collision Interrupt Flag bit (must be cleared by software) 1 = Transmitted word is not equal to the received word 0 = Transmitted word is equal to the received word  2017-2019 Microchip Technology Inc. DS70005319D-page 589 dsPIC33CH128MP508 FAMILY REGISTER 13-4: U-0 UxSTAH: UARTx STATUS REGISTER HIGH R/W-0 — UTXISEL2 R/W-0 UTXISEL1 R/W-0 UTXISEL0 U-0 — R/W-0 URXISEL2 R/W-0 (1) R/W-0 (1) URXISEL1 URXISEL0(1) bit 15 bit 8 HS/R/W-0 R/W-0 R/S-1 R-0 R-1 R-1 R/S-1 R-0 TXWRE STPMD UTXBE UTXBF RIDLE XON URXBE URXBF bit 7 bit 0 Legend: HS = Hardware Settable bit S = Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 UTXISEL[2:0]: UART Transmit Interrupt Select bits 111 = Sets transmit interrupt when there is one empty slot left in the buffer ... 010 = Sets transmit interrupt when there are six empty slots or more in the buffer 001 = Sets transmit interrupt when there are seven empty slots or more in the buffer 000 = Sets transmit interrupt when there are eight empty slots in the buffer; TX buffer is empty bit 11 Unimplemented: Read as ‘0’ bit 10-8 URXISEL[2:0]: UART Receive Interrupt Select bits(1) 111 = Triggers receive interrupt when there are eight words in the buffer; RX buffer is full ... 001 = Triggers receive interrupt when there are two words or more in the buffer 000 = Triggers receive interrupt when there is one word or more in the buffer bit 7 TXWRE: TX Write Transmit Error Status bit LIN and Parity Modes: 1 = A new byte was written when the buffer was full or when P2[8:0] = 0 (must be cleared by software) 0 = No error Address Detect Mode: 1 = A new byte was written when the buffer was full or to P1[8:0] when P1x was full (must be cleared by software) 0 = No error Other Modes: 1 = A new byte was written when the buffer was full (must be cleared by software) 0 = No error bit 6 STPMD: Stop Bit Detection Mode bit 1 = Triggers RXIF at the end of the last Stop bit 0 = Triggers RXIF in the middle of the first (or second, depending on the STSEL[1:0] setting) Stop bit bit 5 UTXBE: UART TX Buffer Empty Status bit 1 = Transmit buffer is empty; writing ‘1’ when UTXEN = 0 will reset the TX FIFO Pointers and counters 0 = Transmit buffer is not empty bit 4 UTXBF: UART TX Buffer Full Status bit 1 = Transmit buffer is full 0 = Transmit buffer is not full bit 3 RIDLE: Receive Idle bit 1 = UART RX line is in the Idle state 0 = UART RX line is receiving something Note 1: The receive watermark interrupt is not set if PERR or FERR is set and the corresponding IE bit is set. DS70005319D-page 590  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 13-4: UxSTAH: UARTx STATUS REGISTER HIGH (CONTINUED) bit 2 XON: UART in XON Mode bit Only valid when FLO[1:0] control bits are set to XON/XOFF mode. 1 = UART has received XON 0 = UART has not received XON or XOFF was received bit 1 URXBE: UART RX Buffer Empty Status bit 1 = Receive buffer is empty; writing ‘1’ when URXEN = 0 will reset the RX FIFO Pointers and counters 0 = Receive buffer is not empty bit 0 URXBF: UART RX Buffer Full Status bit 1 = Receive buffer is full 0 = Receive buffer is not full Note 1: The receive watermark interrupt is not set if PERR or FERR is set and the corresponding IE bit is set.  2017-2019 Microchip Technology Inc. DS70005319D-page 591 dsPIC33CH128MP508 FAMILY REGISTER 13-5: R/W-0 UxBRG: UARTx BAUD RATE REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 BRG[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 BRG[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 x = Bit is unknown BRG[15:0]: Baud Rate Divisor bits REGISTER 13-6: UxBRGH: UARTx BAUD RATE REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 — — — — R/W-0 R/W-0 R/W-0 R/W-0 BRG[19:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-4 Unimplemented: Read as ‘0’ bit 3-0 BRG[19:16]: Baud Rate Divisor bits DS70005319D-page 592 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 13-7: UxRXREG: UARTx RECEIVE BUFFER REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R-x R-x R-x R-x R-x R-x R-x R-x RXREG[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-8 Unimplemented: Read as ‘0’ bit 7-0 RXREG[7:0]: Received Character Data bits 7-0 REGISTER 13-8: x = Bit is unknown UxTXREG: UARTx TRANSMIT BUFFER REGISTER W-x U-0 U-0 U-0 U-0 U-0 U-0 U-0 LAST — — — — — — — bit 15 bit 8 W-x W-x W-x W-x W-x W-x W-x W-x TXREG[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 LAST: Last Byte Indicator for Smart Card Support bit bit 14-8 Unimplemented: Read as ‘0’ bit 7-0 TXREG[7:0]: Transmitted Character Data bits 7-0 If the buffer is full, further writes to the buffer are ignored.  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 593 dsPIC33CH128MP508 FAMILY REGISTER 13-9: UxP1: UARTx TIMING PARAMETER 1 REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — — P1[8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 P1[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-9 Unimplemented: Read as ‘0’ bit 8-0 P1[8:0]: Parameter 1 bits DMX TX: Number of Bytes to Transmit – 1 (not including Start code). LIN Master TX: PID to transmit (bits[5:0]). Asynchronous TX with Address Detect: Address to transmit. A ‘1’ is automatically inserted into bit 9 (bits[7:0]). Smart Card Mode: Guard Time Counter bits. This counter is operated on the bit clock whose period is always equal to one ETU (bits[8:0]). Other Modes: Not used. DS70005319D-page 594  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 13-10: UxP2: UARTx TIMING PARAMETER 2 REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — — P2[8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 P2[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-9 Unimplemented: Read as ‘0’ bit 8-0 P2[8:0]: Parameter 2 bits DMX RX: The first byte number to receive – 1, not including Start code (bits[8:0]). LIN Slave TX: Number of bytes to transmit (bits[7:0]). Asynchronous RX with Address Detect: Address to start matching (bits[7:0]). Smart Card Mode: Block Time Counter bits. This counter is operated on the bit clock whose period is always equal to one ETU (bits[8:0]). Other Modes: Not used.  2017-2019 Microchip Technology Inc. DS70005319D-page 595 dsPIC33CH128MP508 FAMILY REGISTER 13-11: UxP3: UARTx TIMING PARAMETER 3 REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 P3[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 P3[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown P3[15:0]: Parameter 3 bits DMX RX: The last byte number to receive – 1, not including Start code (bits[8:0]). LIN Slave RX: Number of bytes to receive (bits[7:0]). Asynchronous RX: Used to mask the UxP2 address bits; 1 = P2 address bit is used, 0 = P2 address bit is masked off (bits[7:0]). Smart Card Mode: Waiting Time Counter bits (bits[15:0]). Other Modes: Not used. REGISTER 13-12: UxP3H: UARTx TIMING PARAMETER 3 REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 P3[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-8 Unimplemented: Read as ‘0’ bit 7-0 P3[23:16]: Parameter 3 High bits Smart Card Mode: Waiting Time Counter bits (bits[23:16]). Other Modes: Not used. DS70005319D-page 596 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 13-13: UxTXCHK: UARTx TRANSMIT CHECKSUM REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TXCHK[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-8 Unimplemented: Read as ‘0’ bit 7-0 TXCHK[7:0]: Transmit Checksum bits (calculated from TX words) LIN Modes: C0EN = 1: Sum of all transmitted data + addition carries, including PID. C0EN = 0: Sum of all transmitted data + addition carries, excluding PID. LIN Slave: Cleared when Break is detected. LIN Master/Slave: Cleared when Break is detected. Other Modes: C0EN = 1: Sum of every byte transmitted + addition carries. C0EN = 0: Value remains unchanged.  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 597 dsPIC33CH128MP508 FAMILY REGISTER 13-14: UxRXCHK: UARTx RECEIVE CHECKSUM REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RXCHK[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7-0 RXCHK[7:0]: Receive Checksum bits (calculated from RX words) LIN Modes: C0EN = 1: Sum of all received data + addition carries, including PID. C0EN = 0: Sum of all received data + addition carries, excluding PID. LIN Slave: Cleared when Break is detected. LIN Master/Slave: Cleared when Break is detected. Other Modes: C0EN = 1: Sum of every byte received + addition carries. C0EN = 0: Value remains unchanged. DS70005319D-page 598  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 13-15: UxSCCON: UARTx SMART CARD CONFIGURATION REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 — — TXRPT1 TXRPT0 CONV T0PD PRTCL — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-6 Unimplemented: Read as ‘0’ bit 5-4 TXRPT[1:0]: Transmit Repeat Selection bits 11 = Retransmit the error byte four times 10 = Retransmit the error byte three times 01 = Retransmit the error byte twice 00 = Retransmit the error byte once bit 3 CONV: Logic Convention Selection bit 1 = Inverse logic convention 0 = Direct logic convention bit 2 T0PD: Pull-Down Duration for T = 0 Error Handling bit 1 = 2 ETU 0 = 1 ETU bit 1 PRTCL: Smart Card Protocol Selection bit 1=T=1 0=T=0 bit 0 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 599 dsPIC33CH128MP508 FAMILY REGISTER 13-16: UxSCINT: UARTx SMART CARD INTERRUPT REGISTER U-0 U-0 HS/R/W-0 HS/R/W-0 U-0 HS/R/W-0 HS/R/W-0 HS/R/W-0 — — RXRPTIF TXRPTIF — BTCIF WTCIF GTCIF bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 — — RXRPTIE TXRPTIE — BTCIE WTCIE GTCIE bit 7 bit 0 Legend: HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 RXRPTIF: Receive Repeat Interrupt Flag bit 1 = Parity error has persisted after the same character has been received five times (four retransmits) 0 = Flag is cleared bit 12 TXRPTIF: Transmit Repeat Interrupt Flag bit 1 = Line error has been detected after the last retransmit per TXRPT[1:0] 0 = Flag is cleared bit 11 Unimplemented: Read as ‘0’ bit 10 BTCIF: Block Time Counter Interrupt Flag bit 1 = Block Time Counter has reached 0 0 = Block Time Counter has not reached 0 bit 9 WTCIF: Waiting Time Counter Interrupt Flag bit 1 = Waiting Time Counter has reached 0 0 = Waiting Time Counter has not reached 0 bit 8 GTCIF: Guard Time Counter Interrupt Flag bit 1 = Guard Time Counter has reached 0 0 = Guard Time Counter has not reached 0 bit 7-6 Unimplemented: Read as ‘0’ bit 5 RXRPTIE: Receive Repeat Interrupt Enable bit 1 = An interrupt is invoked when a parity error has persisted after the same character has been received five times (four retransmits) 0 = Interrupt is disabled bit 4 TXRPTIE: Transmit Repeat Interrupt Enable bit 1 = An interrupt is invoked when a line error is detected after the last retransmit per TXRPT[1:0] has been completed 0 = Interrupt is disabled bit 3 Unimplemented: Read as ‘0’ bit 2 BTCIE: Block Time Counter Interrupt Enable bit 1 = Block Time Counter interrupt is enabled 0 = Block Time Counter interrupt is disabled bit 1 WTCIE: Waiting Time Counter Interrupt Enable bit 1 = Waiting Time Counter interrupt is enabled 0 = Waiting Time Counter Interrupt is disabled bit 0 GTCIE: Guard Time Counter interrupt enable bit 1 = Guard Time Counter interrupt is enabled 0 = Guard Time Counter interrupt is disabled DS70005319D-page 600  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 13-17: UxINT: UARTx INTERRUPT REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 HS/R/W-0 bit 8 HS/R/W-0 U-0 U-0 U-0 R/W-0 U-0 U-0 ABDIF — — — ABDIE — — WUIF bit 7 bit 0 Legend: HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7 WUIF: Wake-up Interrupt Flag bit 1 = Sets when WAKE = 1 and RX makes a ‘1’-to-‘0’ transition; triggers event interrupt (must be cleared by software) 0 = WAKE is not enabled or WAKE is enabled, but no wake-up event has occurred bit 6 ABDIF: Auto-Baud Completed Interrupt Flag bit 1 = Sets when ABD sequence makes the final ‘1’-to-‘0’ transition; triggers event interrupt (must be cleared by software) 0 = ABAUD is not enabled or ABAUD is enabled but auto-baud has not completed bit 5-3 Unimplemented: Read as ‘0’ bit 2 ABDIE: Auto-Baud Completed Interrupt Enable Flag bit 1 = Allows ABDIF to set an event interrupt 0 = ABDIF does not set an event interrupt bit 1-0 Unimplemented: Read as ‘0’  2017-2019 Microchip Technology Inc. DS70005319D-page 601 dsPIC33CH128MP508 FAMILY NOTES: DS70005319D-page 602  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 14.0 SERIAL PERIPHERAL INTERFACE (SPI) Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “Serial Peripheral Interface (SPI) with Audio Codec Support” (www.microchip.com/DS70005136) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). 2: The SPI is Identical for both Master core and Slave core. The x is common for both Master and Slave (where the x represents the number of the specific module being addressed). The number of SPI modules available on the Master and Slave is different and they are located in different SFR locations. 3: All associated register names are the same on the Master core and the Slave core. The Slave code will be developed in a separate project in MPLAB® X IDE with the device selection, dsPIC33CH128MP508S1, where the S1 indicates the Slave device. The Master is SPI1 and SPI2, and the Slave is SPI1. Table 14-1 shows an overview of the SPI module. TABLE 14-1: SPI MODULE OVERVIEW Number of SPI Modules Identical (Modules) Master Core 2 Yes Slave Core 1 Yes The Serial Peripheral Interface (SPI) module is a synchronous serial interface, useful for communicating with other peripheral or microcontroller devices. These peripheral devices may be serial EEPROMs, shift registers, display drivers, A/D Converters, etc. The SPI module is compatible with the Motorola® SPI and SIOP interfaces. All devices in the dsPIC33CH128MP508 family include three SPI modules; two SPIs for the Master core and one for the Slave core. One of the SPI modules can work up to 50 MHz speed when selected as a non-PPS pin. For the Master core, it will be SPI2 and for the Slave core, it will be SPI1. The selection is done using the SPI2PIN bit (FDEVOPT[13]) for the Master and the S1SPI1PIN bit (FS1DEVOPT[13]) for the Slave. If the bit for SPI2PIN/S1SPI1PIN is ‘1’, the PPS pin will be used. If the SPI2PIN/S1SPI1PIN is ‘0’, it will use the dedicated SPI pads.  2017-2019 Microchip Technology Inc. The module supports operation in two Buffer modes. In Standard mode, data are shifted through a single serial buffer. In Enhanced Buffer mode, data are shifted through a FIFO buffer. The FIFO level depends on the configured mode. Note: FIFO depth for this device is four (in 8-Bit Data mode). Variable length data can be transmitted and received, from 2 to 32 bits. Note: Do not perform Read-Modify-Write operations (such as bit-oriented instructions) on the SPIxBUF register in either Standard or Enhanced Buffer mode. The module also supports a basic framed SPI protocol while operating in either Master or Slave mode. A total of four framed SPI configurations are supported. The module also supports Audio modes. Four different Audio modes are available. • I2S mode • Left Justified mode • Right Justified mode • PCM/DSP mode In each of these modes, the serial clock is free-running and audio data are always transferred. If an audio protocol data transfer takes place between two devices, then usually one device is the Master and the other is the Slave. However, audio data can be transferred between two Slaves. Because the audio protocols require free-running clocks, the Master can be a third-party controller. In either case, the Master generates two free-running clocks: SCKx and LRC (Left, Right Channel Clock/SSx/FSYNC). The SPI serial interface consists of four pins: • SDIx/S1SDIx: Serial Data Input • SDOx/S1SDOx: Serial Data Output • SCKx/S1SCKx: Shift Clock Input or Output • SSx/S1SSx: Active-Low Slave Select or Frame Synchronization I/O Pulse The SPI module can be configured to operate using two, three or four pins. In the 3-pin mode, SSx/S1SSx is not used. In the 2-pin mode, both SDOx/S1SDOx and SSx/S1SSx are not used. DS70005319D-page 603 dsPIC33CH128MP508 FAMILY The SPI module has the ability to generate three interrupts reflecting the events that occur during the data communication. The following types of interrupts can be generated: 1. Receive interrupts are signalled by SPIxRXIF. This event occurs when: - RX watermark interrupt - SPIROV = 1 - SPIRBF = 1 - SPIRBE = 1 provided the respective mask bits are enabled in SPIxIMSKL/H. 2. Transmit interrupts are signalled by SPIxTXIF. This event occurs when: - TX watermark interrupt - SPITUR = 1 - SPITBF = 1 - SPITBE = 1 provided the respective mask bits are enabled in SPIxIMSKL/H. 3. General interrupts are signalled by SPIxGIF. This event occurs when: - FRMERR = 1 - SPIBUSY = 1 - SRMT = 1 provided the respective mask bits are enabled in SPIxIMSKL/H. Block diagrams of the module in Standard and Enhanced modes are shown in Figure 14-1 and Figure 14-2. Note: In this section, the SPI modules are referred to together as SPIx, or separately as SPI1, SPI2 or SPI3. Special Function Registers will follow a similar notation. For example, SPIxCON1 and SPIxCON2 refer to the control registers for any of the three SPI modules. DS70005319D-page 604 To set up the SPIx module for the Standard Master mode of operation: 1. 2. 3. 4. 5. If using interrupts: a) Clear the interrupt flag bits in the respective IFSx register. b) Set the interrupt enable bits in the respective IECx register. c) Write the SPIxIP bits in the respective IPCx register to set the interrupt priority. Write the desired settings to the SPIxCON1L and SPIxCON1H registers with the MSTEN bit (SPIxCON1L[5]) = 1. Clear the SPIROV bit (SPIxSTATL[6]). Enable SPIx operation by setting the SPIEN bit (SPIxCON1L[15]). Write the data to be transmitted to the SPIxBUFL and SPIxBUFH registers. Transmission (and reception) will start as soon as data are written to the SPIxBUFL and SPIxBUFH registers. To set up the SPIx module for the Standard Slave mode of operation: 1. 2. 3. 4. 5. 6. 7. Clear the SPIxBUF registers. If using interrupts: a) Clear the SPIxBUFL and SPIxBUFH registers. b) Set the interrupt enable bits in the respective IECx register. c) Write the SPIxIP bits in the respective IPCx register to set the interrupt priority. Write the desired settings to the SPIxCON1L, SPIxCON1H and SPIxCON2L registers with the MSTEN bit (SPIxCON1L[5]) = 0. Clear the SMP bit. If the CKE bit (SPIxCON1L[8]) is set, then the SSEN bit (SPIxCON1L[7]) must be set to enable the SSx pin. Clear the SPIROV bit (SPIxSTATL[6]). Enable SPIx operation by setting the SPIEN bit (SPIxCON1L[15]).  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 14-1: SPIx MODULE BLOCK DIAGRAM (STANDARD MODE) Internal Data Bus Write Read SPIxTXB SPIxRXB SPIxURDT MSB Receive Transmit SPIxTXSR SPIxRXSR SDIx MSB 0 Shift Control SDOx SSx/FSYNC SSx & FSYNC Control Clock Control 1 TXELM[5:0] = 6’b0 URDTEN Edge Select MCLKEN Baud Rate Generator SCKx Edge Select  2017-2019 Microchip Technology Inc. Clock Control MCLK PBCLK Enable Master Clock DS70005319D-page 605 dsPIC33CH128MP508 FAMILY To set up the SPIx module for the Enhanced Buffer Master mode of operation: To set up the SPIx module for the Enhanced Buffer Slave mode of operation: 1. 1. 2. 2. 3. 4. 5. 6. If using interrupts: a) Clear the interrupt flag bits in the respective IFSx register. b) Set the interrupt enable bits in the respective IECx register. c) Write the SPIxIP bits in the respective IPCx register. Write the desired settings to the SPIxCON1L, SPIxCON1H and SPIxCON2L registers with MSTEN (SPIxCON1L[5]) = 1. Clear the SPIROV bit (SPIxSTATL[6]). Select Enhanced Buffer mode by setting the ENHBUF bit (SPIxCON1L[0]). Enable SPIx operation by setting the SPIEN bit (SPIxCON1L[15]). Write the data to be transmitted to the SPIxBUFL and SPIxBUFH registers. Transmission (and reception) will start as soon as data are written to the SPIxBUFL and SPIxBUFH registers. FIGURE 14-2: 3. 4. 5. 6. 7. 8. Clear the SPIxBUFL and SPIxBUFH registers. If using interrupts: a) Clear the interrupt flag bits in the respective IFSx register. b) Set the interrupt enable bits in the respective IECx register. c) Write the SPIxIP bits in the respective IPCx register to set the interrupt priority. Write the desired settings to the SPIxCON1L, SPIxCON1H and SPIxCON2L registers with the MSTEN bit (SPIxCON1L[5]) = 0. Clear the SMP bit. If the CKE bit is set, then the SSEN bit must be set, thus enabling the SSx pin. Clear the SPIROV bit (SPIxSTATL[6]). Select Enhanced Buffer mode by setting the ENHBUF bit (SPIxCON1L[0]). Enable SPIx operation by setting the SPIEN bit (SPIxCON1L[15]). SPIx MODULE BLOCK DIAGRAM (ENHANCED MODE) Internal Data Bus Write Read SPIxRXB SPIxTXB SPIxURDT MSB Transmit Receive SPIxTXSR SPIxRXSR SDIx MSB 0 Shift Control SDOx SSx/FSYNC SSx and FSYNC Control Clock Control 1 TXELM[5:0] = 6’b0 URDTEN Edge Select MCLKEN Baud Rate Generator SCKx Edge Select DS70005319D-page 606 Clock Control MCLK PBCLK Enable Master Clock  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY To set up the SPIx module for Audio mode: 1. 2. Clear the SPIxBUFL and SPIxBUFH registers. If using interrupts: a) Clear the interrupt flag bits in the respective IFSx register. b) Set the interrupt enable bits in the respective IECx register. a) Write the SPIxIP bits in the respective IPCx register to set the interrupt priority.  2017-2019 Microchip Technology Inc. 3. 4. 5. 6. Write the desired settings to the SPIxCON1L, SPIxCON1H and SPIxCON2L registers with AUDEN (SPIxCON1H[15]) = 1. Clear the SPIROV bit (SPIxSTATL[6]). Enable SPIx operation by setting the SPIEN bit (SPIxCON1L[15]). Write the data to be transmitted to the SPIxBUFL and SPIxBUFH registers. Transmission (and reception) will start as soon as data are written to the SPIxBUFL and SPIxBUFH registers. DS70005319D-page 607 dsPIC33CH128MP508 FAMILY 14.1 SPI Control/Status Registers REGISTER 14-1: R/W-0 SPIxCON1L: SPIx CONTROL REGISTER 1 LOW U-0 — SPIEN R/W-0 SPISIDL R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DISSDO MODE32(1,4) MODE16(1,4) SMP CKE(1) bit 15 bit 8 R/W-0 R/W-0 (2) CKP SSEN R/W-0 R/W-0 MSTEN R/W-0 DISSDI DISSCK R/W-0 (3) MCLKEN R/W-0 R/W-0 SPIFE ENHBUF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 SPIEN: SPIx On bit 1 = Enables module 0 = Turns off and resets module, disables clocks, disables interrupt event generation, allows SFR modifications bit 14 Unimplemented: Read as ‘0’ bit 13 SPISIDL: SPIx Stop in Idle Mode bit 1 = Halts in CPU Idle mode 0 = Continues to operate in CPU Idle mode bit 12 DISSDO: Disable SDOx Output Port bit 1 = SDOx pin is not used by the module; pin is controlled by port function 0 = SDOx pin is controlled by the module bit 11-10 MODE32 and MODE16: Serial Word Length Select bits(1,4) MODE32 MODE16 1 x 0 1 0 0 8-Bit 24-Bit Data, 32-Bit FIFO, 32-Bit Channel/64-Bit Frame 1 1 1 0 0 1 0 0 AUDEN Communication 32-Bit 0 1 16-Bit 32-Bit Data, 32-Bit FIFO, 32-Bit Channel/64-Bit Frame 16-Bit Data, 16-Bit FIFO, 32-Bit Channel/64-Bit Frame 16-Bit FIFO, 16-Bit Channel/32-Bit Frame bit 9 SMP: SPIx Data Input Sample Phase bit Master Mode: 1 = Input data are sampled at the end of data output time 0 = Input data are sampled at the middle of data output time Slave Mode: Input data are always sampled at the middle of data output time, regardless of the SMP setting. bit 8 CKE: SPIx Clock Edge Select bit(1) 1 = Transmit happens on transition from active clock state to Idle clock state 0 = Transmit happens on transition from Idle clock state to active clock state Note 1: 2: 3: 4: When AUDEN (SPIxCON1H[15]) = 1, this module functions as if CKE = 0, regardless of its actual value. When FRMEN = 1, SSEN is not used. MCLKEN can only be written when the SPIEN bit = 0. This channel is not meaningful for DSP/PCM mode as LRC follows FRMSYPW. DS70005319D-page 608  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 14-1: SPIxCON1L: SPIx CONTROL REGISTER 1 LOW (CONTINUED) bit 7 SSEN: Slave Select Enable bit (Slave mode)(2) 1 = SSx pin is used by the macro in Slave mode; SSx pin is used as the Slave select input 0 = SSx pin is not used by the macro (SSx pin will be controlled by the port I/O) bit 6 CKP: Clock Polarity Select bit 1 = Idle state for clock is a high level; active state is a low level 0 = Idle state for clock is a low level; active state is a high level bit 5 MSTEN: Master Mode Enable bit 1 = Master mode 0 = Slave mode bit 4 DISSDI: Disable SDIx Input Port bit 1 = SDIx pin is not used by the module; pin is controlled by port function 0 = SDIx pin is controlled by the module bit 3 DISSCK: Disable SCKx Output Port bit 1 = SCKx pin is not used by the module; pin is controlled by port function 0 = SCKx pin is controlled by the module bit 2 MCLKEN: Master Clock Enable bit(3) 1 = MCLK is used by the BRG 0 = PBCLK is used by the BRG bit 1 SPIFE: Frame Sync Pulse Edge Select bit 1 = Frame Sync pulse (Idle-to-active edge) coincides with the first bit clock 0 = Frame Sync pulse (Idle-to-active edge) precedes the first bit clock bit 0 ENHBUF: Enhanced Buffer Enable bit 1 = Enhanced Buffer mode is enabled 0 = Enhanced Buffer mode is disabled Note 1: 2: 3: 4: When AUDEN (SPIxCON1H[15]) = 1, this module functions as if CKE = 0, regardless of its actual value. When FRMEN = 1, SSEN is not used. MCLKEN can only be written when the SPIEN bit = 0. This channel is not meaningful for DSP/PCM mode as LRC follows FRMSYPW.  2017-2019 Microchip Technology Inc. DS70005319D-page 609 dsPIC33CH128MP508 FAMILY REGISTER 14-2: R/W-0 R/W-0 (1) AUDEN SPIxCON1H: SPIx CONTROL REGISTER 1 HIGH SPISGNEXT R/W-0 IGNROV R/W-0 IGNTUR R/W-0 R/W-0 (2) AUDMONO URDTEN R/W-0 (3) R/W-0 (4) AUDMOD1 AUDMOD0(4) bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FRMEN FRMSYNC FRMPOL MSSEN FRMSYPW FRMCNT2 FRMCNT1 FRMCNT0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 AUDEN: Audio Codec Support Enable bit(1) 1 = Audio protocol is enabled; MSTEN controls the direction of both SCKx and frame (a.k.a. LRC), and this module functions as if FRMEN = 1, FRMSYNC = MSTEN, FRMCNT[2:0] = 001 and SMP = 0, regardless of their actual values 0 = Audio protocol is disabled bit 14 SPISGNEXT: SPIx Sign-Extend RX FIFO Read Data Enable bit 1 = Data from RX FIFO are sign-extended 0 = Data from RX FIFO are not sign-extended bit 13 IGNROV: Ignore Receive Overflow bit 1 = A Receive Overflow (ROV) is NOT a critical error; during ROV, data in the FIFO are not overwritten by the receive data 0 = A ROV is a critical error that stops SPI operation bit 12 IGNTUR: Ignore Transmit Underrun bit 1 = A Transmit Underrun (TUR) is NOT a critical error and data indicated by URDTEN are transmitted until the SPIxTXB is not empty 0 = A TUR is a critical error that stops SPI operation bit 11 AUDMONO: Audio Data Format Transmit bit(2) 1 = Audio data are mono (i.e., each data word is transmitted on both left and right channels) 0 = Audio data are stereo bit 10 URDTEN: Transmit Underrun Data Enable bit(3) 1 = Transmits data out of SPIxURDT register during Transmit Underrun conditions 0 = Transmits the last received data during Transmit Underrun conditions bit 9-8 AUDMOD[1:0]: Audio Protocol Mode Selection bits(4) 11 = PCM/DSP mode 10 = Right Justified mode: This module functions as if SPIFE = 1, regardless of its actual value 01 = Left Justified mode: This module functions as if SPIFE = 1, regardless of its actual value 00 = I2S mode: This module functions as if SPIFE = 0, regardless of its actual value bit 7 FRMEN: Framed SPIx Support bit 1 = Framed SPIx support is enabled (SSx pin is used as the FSYNC input/output) 0 = Framed SPIx support is disabled Note 1: 2: 3: 4: AUDEN can only be written when the SPIEN bit = 0. AUDMONO can only be written when the SPIEN bit = 0 and is only valid for AUDEN = 1. URDTEN is only valid when IGNTUR = 1. AUDMOD[1:0] can only be written when the SPIEN bit = 0 and is only valid when AUDEN = 1. When NOT in PCM/DSP mode, this module functions as if FRMSYPW = 1, regardless of its actual value. DS70005319D-page 610  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 14-2: SPIxCON1H: SPIx CONTROL REGISTER 1 HIGH (CONTINUED) bit 6 FRMSYNC: Frame Sync Pulse Direction Control bit 1 = Frame Sync pulse input (Slave) 0 = Frame Sync pulse output (Master) bit 5 FRMPOL: Frame Sync/Slave Select Polarity bit 1 = Frame Sync pulse/Slave select is active-high 0 = Frame Sync pulse/Slave select is active-low bit 4 MSSEN: Master Mode Slave Select Enable bit 1 = SPIx Slave select support is enabled with polarity determined by FRMPOL (SSx pin is automatically driven during transmission in Master mode) 0 = Slave select SPIx support is disabled (SSx pin will be controlled by port I/O) bit 3 FRMSYPW: Frame Sync Pulse-Width bit 1 = Frame Sync pulse is one serial word length wide (as defined by MODE[32,16]/WLENGTH[4:0]) 0 = Frame Sync pulse is one clock (SCKx) wide bit 2-0 FRMCNT[2:0]: Frame Sync Pulse Counter bits Controls the number of serial words transmitted per Sync pulse. 111 = Reserved 110 = Reserved 101 = Generates a Frame Sync pulse on every 32 serial words 100 = Generates a Frame Sync pulse on every 16 serial words 011 = Generates a Frame Sync pulse on every 8 serial words 010 = Generates a Frame Sync pulse on every 4 serial words 001 = Generates a Frame Sync pulse on every 2 serial words (value used by audio protocols) 000 = Generates a Frame Sync pulse on each serial word Note 1: 2: 3: 4: AUDEN can only be written when the SPIEN bit = 0. AUDMONO can only be written when the SPIEN bit = 0 and is only valid for AUDEN = 1. URDTEN is only valid when IGNTUR = 1. AUDMOD[1:0] can only be written when the SPIEN bit = 0 and is only valid when AUDEN = 1. When NOT in PCM/DSP mode, this module functions as if FRMSYPW = 1, regardless of its actual value.  2017-2019 Microchip Technology Inc. DS70005319D-page 611 dsPIC33CH128MP508 FAMILY REGISTER 14-3: SPIxCON2L: SPIx CONTROL REGISTER 2 LOW U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 WLENGTH[4:0](1,2) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-5 Unimplemented: Read as ‘0’ bit 4-0 WLENGTH[4:0]: Variable Word Length bits(1,2) 11111 = 32-bit data 11110 = 31-bit data 11101 = 30-bit data 11100 = 29-bit data 11011 = 28-bit data 11010 = 27-bit data 11001 = 26-bit data 11000 = 25-bit data 10111 = 24-bit data 10110 = 23-bit data 10101 = 22-bit data 10100 = 21-bit data 10011 = 20-bit data 10010 = 19-bit data 10001 = 18-bit data 10000 = 17-bit data 01111 = 16-bit data 01110 = 15-bit data 01101 = 14-bit data 01100 = 13-bit data 01011 = 12-bit data 01010 = 11-bit data 01001 = 10-bit data 01000 = 9-bit data 00111 = 8-bit data 00110 = 7-bit data 00101 = 6-bit data 00100 = 5-bit data 00011 = 4-bit data 00010 = 3-bit data 00001 = 2-bit data 00000 = See MODE[32,16] bits in SPIxCON1L[11:10] Note 1: 2: x = Bit is unknown These bits are effective when AUDEN = 0 only. Varying the length by changing these bits does not affect the depth of the TX/RX FIFO. DS70005319D-page 612  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 14-4: SPIxSTATL: SPIx STATUS REGISTER LOW U-0 U-0 U-0 HS/R/C-0 HSC/R-0 U-0 U-0 HSC/R-0 — — — FRMERR SPIBUSY — — SPITUR(1) bit 15 bit 8 HSC/R-0 HS/R/C-0 HSC/R-1 U-0 HSC/R-1 U-0 HSC/R-0 HSC/R-0 SRMT SPIROV SPIRBE — SPITBE — SPITBF SPIRBF bit 7 bit 0 Legend: C = Clearable bit U = Unimplemented, read as ‘0’ R = Readable bit W = Writable bit HSC = Hardware Settable/Clearable bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared HS = Hardware Settable bit bit 15-13 Unimplemented: Read as ‘0’ bit 12 FRMERR: SPIx Frame Error Status bit 1 = Frame error is detected 0 = No frame error is detected bit 11 SPIBUSY: SPIx Activity Status bit 1 = Module is currently busy with some transactions 0 = No ongoing transactions (at time of read) bit 10-9 Unimplemented: Read as ‘0’ bit 8 SPITUR: SPIx Transmit Underrun Status bit(1) 1 = Transmit buffer has encountered a Transmit Underrun condition 0 = Transmit buffer does not have a Transmit Underrun condition bit 7 SRMT: Shift Register Empty Status bit 1 = No current or pending transactions (i.e., neither SPIxTXB or SPIxTXSR contains data to transmit) 0 = Current or pending transactions bit 6 SPIROV: SPIx Receive Overflow Status bit 1 = A new byte/half-word/word has been completely received when the SPIxRXB was full 0 = No overflow bit 5 SPIRBE: SPIx RX Buffer Empty Status bit 1 = RX buffer is empty 0 = RX buffer is not empty Standard Buffer Mode: Automatically set in hardware when SPIxBUF is read from, reading SPIxRXB. Automatically cleared in hardware when SPIx transfers data from SPIxRXSR to SPIxRXB. Enhanced Buffer Mode: Indicates RXELM[5:0] = 000000. bit 4 Unimplemented: Read as ‘0’ Note 1: SPITUR is cleared when SPIEN = 0. When IGNTUR = 1, SPITUR provides dynamic status of the Transmit Underrun condition, but does not stop RX/TX operation and does not need to be cleared by software.  2017-2019 Microchip Technology Inc. DS70005319D-page 613 dsPIC33CH128MP508 FAMILY REGISTER 14-4: SPIxSTATL: SPIx STATUS REGISTER LOW (CONTINUED) bit 3 SPITBE: SPIx Transmit Buffer Empty Status bit 1 = SPIxTXB is empty 0 = SPIxTXB is not empty Standard Buffer Mode: Automatically set in hardware when SPIx transfers data from SPIxTXB to SPIxTXSR. Automatically cleared in hardware when SPIxBUF is written, loading SPIxTXB. Enhanced Buffer Mode: Indicates TXELM[5:0] = 000000. bit 2 Unimplemented: Read as ‘0’ bit 1 SPITBF: SPIx Transmit Buffer Full Status bit 1 = SPIxTXB is full 0 = SPIxTXB not full Standard Buffer Mode: Automatically set in hardware when SPIxBUF is written, loading SPIxTXB. Automatically cleared in hardware when SPIx transfers data from SPIxTXB to SPIxTXSR. Enhanced Buffer Mode: Indicates TXELM[5:0] = 111111. bit 0 SPIRBF: SPIx Receive Buffer Full Status bit 1 = SPIxRXB is full 0 = SPIxRXB is not full Standard Buffer Mode: Automatically set in hardware when SPIx transfers data from SPIxRXSR to SPIxRXB. Automatically cleared in hardware when SPIxBUF is read from, reading SPIxRXB. Enhanced Buffer Mode: Indicates RXELM[5:0] = 111111. Note 1: SPITUR is cleared when SPIEN = 0. When IGNTUR = 1, SPITUR provides dynamic status of the Transmit Underrun condition, but does not stop RX/TX operation and does not need to be cleared by software. DS70005319D-page 614  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 14-5: U-0 — SPIxSTATH: SPIx STATUS REGISTER HIGH U-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 — RXELM5(3) RXELM4(2) RXELM3(1) RXELM2 RXELM1 RXELM0 bit 15 bit 8 U-0 — U-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 — TXELM5(3) TXELM4(2) TXELM3(1) TXELM2 TXELM1 TXELM0 bit 7 bit 0 Legend: HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13-8 RXELM[5:0]: Receive Buffer Element Count bits (valid in Enhanced Buffer mode)(1,2,3) bit 7-6 Unimplemented: Read as ‘0’ bit 5-0 TXELM[5:0]: Transmit Buffer Element Count bits (valid in Enhanced Buffer mode)(1,2,3) Note 1: 2: 3: RXELM3 and TXELM3 bits are only present when FIFODEPTH = 8 or higher. RXELM4 and TXELM4 bits are only present when FIFODEPTH = 16 or higher. RXELM5 and TXELM5 bits are only present when FIFODEPTH = 32.  2017-2019 Microchip Technology Inc. DS70005319D-page 615 dsPIC33CH128MP508 FAMILY REGISTER 14-6: SPIxIMSKL: SPIx INTERRUPT MASK REGISTER LOW U-0 U-0 U-0 R/W-0 R/W-0 U-0 U-0 R/W-0 — — — FRMERREN BUSYEN — — SPITUREN bit 15 bit 8 R/W-0 R/W-0 R/W-0 U-0 R/W-0 U-0 R/W-0 R/W-0 SRMTEN SPIROVEN SPIRBEN — SPITBEN — SPITBFEN SPIRBFEN bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-13 Unimplemented: Read as ‘0’ bit 12 FRMERREN: Enable Interrupt Events via FRMERR bit 1 = Frame error generates an interrupt event 0 = Frame error does not generate an interrupt event bit 11 BUSYEN: Enable Interrupt Events via SPIBUSY bit 1 = SPIBUSY generates an interrupt event 0 = SPIBUSY does not generate an interrupt event bit 10-9 Unimplemented: Read as ‘0’ bit 8 SPITUREN: Enable Interrupt Events via SPITUR bit 1 = Transmit Underrun (TUR) generates an interrupt event 0 = Transmit Underrun does not generate an interrupt event bit 7 SRMTEN: Enable Interrupt Events via SRMT bit 1 = Shift Register Empty (SRMT) generates interrupt events 0 = Shift Register Empty does not generate interrupt events bit 6 SPIROVEN: Enable Interrupt Events via SPIROV bit 1 = SPIx Receive Overflow (ROV) generates an interrupt event 0 = SPIx Receive Overflow does not generate an interrupt event bit 5 SPIRBEN: Enable Interrupt Events via SPIRBE bit 1 = SPIx RX buffer empty generates an interrupt event 0 = SPIx RX buffer empty does not generate an interrupt event bit 4 Unimplemented: Read as ‘0’ bit 3 SPITBEN: Enable Interrupt Events via SPITBE bit 1 = SPIx transmit buffer empty generates an interrupt event 0 = SPIx transmit buffer empty does not generate an interrupt event bit 2 Unimplemented: Read as ‘0’ bit 1 SPITBFEN: Enable Interrupt Events via SPITBF bit 1 = SPIx transmit buffer full generates an interrupt event 0 = SPIx transmit buffer full does not generate an interrupt event bit 0 SPIRBFEN: Enable Interrupt Events via SPIRBF bit 1 = SPIx receive buffer full generates an interrupt event 0 = SPIx receive buffer full does not generate an interrupt event DS70005319D-page 616  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 14-7: SPIxIMSKH: SPIx INTERRUPT MASK REGISTER HIGH R/W-0 U-0 R/W-0 RXWIEN — RXMSK5(1) R/W-0 R/W-0 R/W-0 RXMSK4(1,4) RXMSK3(1,3) RXMSK2(1,2) R/W-0 R/W-0 RXMSK1(1) RXMSK0(1) bit 15 bit 8 R/W-0 U-0 TXWIEN — R/W-0 R/W-0 (1) TXMSK5 (1,4) TXMSK4 R/W-0 (1,3) TXMSK3 R/W-0 TXMSK2 (1,2) R/W-0 R/W-0 (1) TXMSK1 TXMSK0(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 RXWIEN: Receive Watermark Interrupt Enable bit 1 = Triggers receive buffer element watermark interrupt when RXMSK[5:0]  RXELM[5:0] 0 = Disables receive buffer element watermark interrupt bit 14 Unimplemented: Read as ‘0’ bit 13-8 RXMSK[5:0]: RX Buffer Mask bits(1,2,3,4) RX mask bits; used in conjunction with the RXWIEN bit. bit 7 TXWIEN: Transmit Watermark Interrupt Enable bit 1 = Triggers transmit buffer element watermark interrupt when TXMSK[5:0] = TXELM[5:0] 0 = Disables transmit buffer element watermark interrupt bit 6 Unimplemented: Read as ‘0’ bit 5-0 TXMSK[5:0]: TX Buffer Mask bits(1,2,3,4) TX mask bits; used in conjunction with the TXWIEN bit. Note 1: 2: 3: 4: Mask values higher than FIFODEPTH are not valid. The module will not trigger a match for any value in this case. RXMSK2 and TXMSK2 bits are only present when FIFODEPTH = 8 or higher. RXMSK3 and TXMSK3 bits are only present when FIFODEPTH = 16 or higher. RXMSK4 and TXMSK4 bits are only present when FIFODEPTH = 32.  2017-2019 Microchip Technology Inc. DS70005319D-page 617 dsPIC33CH128MP508 FAMILY FIGURE 14-3: SPIx MASTER/SLAVE CONNECTION (STANDARD MODE) Processor 2 (SPIx Slave) Processor 1 (SPIx Master) SDIx SDOx Serial Receive Buffer (SPIxRXB)(2) Shift Register (SPIxRXSR) LSb MSb Serial Transmit Buffer (SPIxTXB)(2) SDIx SDOx SDOx SDIx Shift Register (SPIxTXSR) MSb Shift Register (SPIxRXSR) Shift Register (SPIxTXSR) MSb LSb MSb LSb Serial Transmit Buffer (SPIxTXB)(2) SCKx Serial Clock SCKx LSb Serial Receive Buffer (SPIxRXB)(2) SSx(1) SPIx Buffer (SPIxBUF)(2) MSTEN (SPIxCON1L[5]) = 1) Note 1: 2: SPIx Buffer (SPIxBUF)(2) MSSEN (SPIxCON1H[4]) = 1 and MSTEN (SPIxCON1L[5]) = 0 Using the SSx pin in Slave mode of operation is optional. User must write transmit data to read the received data from SPIxBUF. The SPIxTXB and SPIxRXB registers are memory-mapped to SPIxBUF. DS70005319D-page 618  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 14-4: SPIx MASTER/SLAVE CONNECTION (ENHANCED BUFFER MODES) Processor 1 (SPIx Master) Processor 2 (SPIx Slave) SDOx SDIx Serial Transmit FIFO (SPIxTXB)(2) Serial Receive FIFO (SPIxRXB)(2) Shift Register (SPIxRXSR) LSb MSb SDIx SDOx SDOx SDIx Shift Register (SPIxTXSR) MSb Shift Register (SPIxRXSR) Shift Register (SPIxTXSR) MSb LSb MSb LSb Serial Transmit FIFO (SPIxTXB)(2) SCKx Serial Clock SCKx LSb Serial Receive FIFO (SPIxRXB)(2) SSx(1) SPIx Buffer (SPIxBUF)(2) SPIx Buffer (SPIxBUF)(2) MSTEN (SPIxCON1L[5]) = 1) Note 1: 2: FIGURE 14-5: MSSEN (SPIxCON1H[4]) = 1 and MSTEN (SPIxCON1L[5]) = 0 Using the SSx pin in Slave mode of operation is optional. User must write transmit data to read the received data from SPIxBUF. The SPIxTXB and SPIxRXB registers are memory-mapped to SPIxBUF. SPIx MASTER, FRAME MASTER CONNECTION DIAGRAM Processor 2 dsPIC33CH (SPIx Master, Frame Master) SDOx SDIx SDOx SDIx SCKx SSx  2017-2019 Microchip Technology Inc. Serial Clock SCKx Frame Sync Pulse SSx DS70005319D-page 619 dsPIC33CH128MP508 FAMILY FIGURE 14-6: SPIx MASTER, FRAME SLAVE CONNECTION DIAGRAM dsPIC33CH SPIx Master, Frame Slave) Processor 2 SDOx SDIx SDOx SDIx SCKx SSx FIGURE 14-7: Serial Clock Frame Sync Pulse SCKx SSx SPIx SLAVE, FRAME MASTER CONNECTION DIAGRAM Processor 2 dsPIC33CH (SPIx Slave, Frame Master) SDIx SDOx SDOx SDIx SCKx SSx FIGURE 14-8: Serial Clock Frame Sync Pulse SCKx SSx SPIx SLAVE, FRAME SLAVE CONNECTION DIAGRAM Processor 2 dsPIC33CH (SPIx Slave, Frame Slave) SDOx SDIx SDOx SDIx SCKx SSx EQUATION 14-1: Serial Clock Frame Sync Pulse SCKx SSx RELATIONSHIP BETWEEN DEVICE AND SPIx CLOCK SPEED Baud Rate = FPB (2 * (SPIxBRG + 1)) Where: FPB is the Peripheral Bus Clock Frequency. DS70005319D-page 620  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 15.0 INTER-INTEGRATED CIRCUIT (I2C) Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. For more information, refer to “Inter-Integrated Circuit (I2C)” (www.microchip.com/DS70000195) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). 2: The I2C is identical for both Master core and Slave core. The x is common for both Master and Slave (where the x represents the number of the specific module being addressed). The number of I2C modules available on the Master and Slave is different and they are located in different SFR locations. 3: All associated register names are the same on the Master core and the Slave core. The Slave code will be developed in a separate project in MPLAB® X IDE with the device selection, dsPIC33CH128MP508S1, where the S1 indicates the Slave device. The Master I2C is I2C1 and I2C2, and the Slave is I2C1. The Inter-Integrated Circuit (I2C) module is a serial interface useful for communicating with other peripheral or microcontroller devices. These peripheral devices may be serial EEPROMs, display drivers, A/D Converters, etc. 15.1 Communicating as a Master in a Single Master Environment The details of sending a message in Master mode depends on the communication protocol for the device being communicated with. Typically, the sequence of events is as follows: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Assert a Start condition on SDAx and SCLx. Send the I 2C device address byte to the Slave with a write indication. Wait for and verify an Acknowledge from the Slave. Send the first data byte (sometimes known as the command) to the Slave. Wait for and verify an Acknowledge from the Slave. Send the serial memory address low byte to the Slave. Repeat Steps 4 and 5 until all data bytes are sent. Assert a Repeated Start condition on SDAx and SCLx. Send the device address byte to the Slave with a read indication. Wait for and verify an Acknowledge from the Slave. Enable Master reception to receive serial memory data. Generate an ACK or NACK condition at the end of a received byte of data. Generate a Stop condition on SDAx and SCLx. The I2C module supports these features: • Independent Master and Slave Logic • 7-Bit and 10-Bit Device Addresses • General Call Address as Defined in the I2C Protocol • Clock Stretching to Provide Delays for the Processor to Respond to a Slave Data Request • Both 100 kHz and 400 kHz Bus Specifications • Configurable Address Masking • Multi-Master modes to Prevent Loss of Messages in Arbitration • Bus Repeater mode, Allowing the Acceptance of All Messages as a Slave, regardless of the Address • Automatic SCL A block diagram of the module is shown in Figure 15-1.  2017-2019 Microchip Technology Inc. DS70005319D-page 621 dsPIC33CH128MP508 FAMILY FIGURE 15-1: I2Cx BLOCK DIAGRAM Internal Data Bus I2CxRCV Read SCLx Shift Clock I2CxRSR LSB SDAx Match Detect Address Match Write I2CxMSK Write Read I2CxADD Read Start and Stop Bit Detect Write Start and Stop Bit Generation Control Logic I2CxSTAT Collision Detect Read Write I2CxCONL/H Acknowledge Generation Read Clock Stretching Write I2CxTRN LSB Read Shift Clock Reload Control BRG Down Counter Write I2CxBRG Read TCY/2 DS70005319D-page 622  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 15.2 Setting Baud Rate When Operating as a Bus Master 15.3 To compute the Baud Rate Generator reload value, use Equation 15-1. EQUATION 15-1: COMPUTING BAUD RATE RELOAD VALUE(1,2,3) I2CxBRG = ((1/FSCL – Delay) • FP) – 2 Note 1: These clock rate values are for guidance only. The actual clock rate should be measured in its intended application. 2: Typical value of delay varies from 110 ns to 150 ns. 3: I2CxBRG values of 0 to 3 are expressly forbidden. The user should never program the I2CxBRG with a value of 0x0, 0x1, 0x2 or 0x3 as indeterminate results may occur. TABLE 15-1: The I2CxMSK register (Register 15-4) designates address bit positions as “don’t care” for both 7-Bit and 10-Bit Addressing modes. Setting a particular bit location (= 1) in the I2CxMSK register causes the Slave module to respond, whether the corresponding address bit value is a ‘0’ or a ‘1’. For example, when I2CxMSK is set to ‘0010000000’, the Slave module will detect both addresses, ‘0000000000’ and ‘0010000000’. To enable address masking, the Intelligent Peripheral Management Interface (IPMI) must be disabled by clearing the STRICT bit (I2CxCONL[11]). Note: As a result of changes in the I2C protocol, the addresses in Table 15-2 are reserved and will not be Acknowledged in Slave mode. This includes any address mask settings that include any of these addresses. I2Cx CLOCK RATES(1,2) FCY Note 1: 2: Slave Address Masking FSCL I2CxBRG Value Decimal Hexadecimal 100 MHz 1 MHz 41 29 100 MHz 400 kHz 116 74 100 MHz 100 kHz 491 1EB 80 MHz 1 MHz 32 20 80 MHz 400 kHz 92 5C 80 MHz 100 kHz 392 188 60 MHz 1 MHz 24 18 60 MHz 400 kHz 69 45 60 MHz 100 kHz 294 126 40 MHz 1 MHz 15 0F 40 MHz 400 kHz 45 2D 40 MHz 100 kHz 195 C3 20 MHz 1 MHz 7 7 20 MHz 400 kHz 22 16 20 MHz 100 kHz 97 61 Based on FCY = FOSC/2; Doze mode and PLL are disabled. These clock rate values are for guidance only. The actual clock rate can be affected by various system-level parameters. The actual clock rate should be measured in its intended application.  2017-2019 Microchip Technology Inc. DS70005319D-page 623 dsPIC33CH128MP508 FAMILY TABLE 15-2: Slave Address I2Cx RESERVED ADDRESSES(1) R/W Bit Description Address(2) 0000 000 0 General Call 0000 000 1 Start Byte 0000 001 x Cbus Address 0000 01x x Reserved 0000 1xx x HS Mode Master Code 1111 0xx x 10-Bit Slave Upper Byte(3) 1111 1xx x Reserved Note 1: 2: 3: 15.4 The address bits listed here will never cause an address match independent of address mask settings. This address will be Acknowledged only if GCEN = 1. A match on this address can only occur on the upper byte in 10-Bit Addressing mode. SMBus Support The dsPIC33CH128MP508 family devices have support for SMBus through options in the input voltage thresholds. There are two control bits to select one of three options: SMEN (I2CxCONL[8]) and Configuration bit, SMBEN (FDEVOPT[10]). Table 15-3 details the setting of these control bits. DS70005319D-page 624 TABLE 15-3: I2C PIN VOLTAGE THRESHOLD SMEN SFR Bit (I2CxCONL[8]) SMBEN Configuration Bit (FDEVOPT[10]) I2C (default) 0 x SMBus 2.0 1 0 SMBus 3.0 1 1  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 15.5 I2C Control/Status Registers REGISTER 15-1: I2CxCONL: I2Cx CONTROL REGISTER LOW R/W-0 U-0 HC/R/W-0 R/W-1 R/W-0 R/W-0 R/W-0 R/W-0 I2CEN — I2CSIDL SCLREL(1) STRICT A10M DISSLW SMEN bit 15 bit 8 R/W-0 R/W-0 R/W-0 HC/R/W-0 HC/R/W-0 HC/R/W-0 HC/R/W-0 HC/R/W-0 GCEN STREN ACKDT ACKEN RCEN PEN RSEN SEN bit 7 bit 0 Legend: HC = Hardware Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 I2CEN: I2Cx Enable bit (writable from software only) 1 = Enables the I2Cx module, and configures the SDAx and SCLx pins as serial port pins 0 = Disables the I2Cx module; all I2C pins are controlled by port functions bit 14 Unimplemented: Read as ‘0’ bit 13 I2CSIDL: I2Cx Stop in Idle Mode bit 1 = Discontinues module operation when device enters Idle mode 0 = Continues module operation in Idle mode bit 12 SCLREL: SCLx Release Control bit (I2C Slave mode only)(1) 1 = Releases the SCLx clock 0 = Holds the SCLx clock low (clock stretch) If STREN = 1:(2) User software may write ‘0’ to initiate a clock stretch and write ‘1’ to release the clock. Hardware clears at the beginning of every Slave data byte transmission. Hardware clears at the end of every Slave address byte reception. Hardware clears at the end of every Slave data byte reception. If STREN = 0: User software may only write ‘1’ to release the clock. Hardware clears at the beginning of every Slave data byte transmission. Hardware clears at the end of every Slave address byte reception. bit 11 STRICT: I2Cx Strict Reserved Address Rule Enable bit 1 = Strict Reserved Addressing is enforced; for reserved addresses, refer to Table 15-2. (In Slave Mode) – The device doesn’t respond to reserved address space and addresses falling in that category are NACKed. (In Master Mode) – The device is allowed to generate addresses with reserved address space. 0 = Reserved Addressing would be Acknowledged. (In Slave Mode) – The device will respond to an address falling in the reserved address space. When there is a match with any of the reserved addresses, the device will generate an ACK. (In Master Mode) – Reserved. bit 10 A10M: 10-Bit Slave Address Flag bit 1 = I2CxADD is a 10-bit Slave address 0 = I2CxADD is a 7-bit Slave address bit 9 DISSLW: Slew Rate Control Disable bit 1 = Slew rate control is disabled for Standard Speed mode (100 kHz, also disabled for 1 MHz mode) 0 = Slew rate control is enabled for High-Speed mode (400 kHz) Note 1: 2: Automatically cleared to ‘0’ at the beginning of Slave transmission; automatically cleared to ‘0’ at the end of Slave reception. Automatically cleared to ‘0’ at the beginning of Slave transmission.  2017-2019 Microchip Technology Inc. DS70005319D-page 625 dsPIC33CH128MP508 FAMILY REGISTER 15-1: I2CxCONL: I2Cx CONTROL REGISTER LOW (CONTINUED) bit 8 SMEN: SMBus Input Levels Enable bit 1 = Enables input logic so thresholds are compliant with the SMBus specification 0 = Disables SMBus-specific inputs bit 7 GCEN: General Call Enable bit (I2C Slave mode only) 1 = Enables interrupt when a general call address is received in I2CxRSR; module is enabled for reception 0 = General call address is disabled. bit 6 STREN: SCLx Clock Stretch Enable bit In I2C Slave mode only; used in conjunction with the SCLREL bit. 1 = Enables clock stretching 0 = Disables clock stretching bit 5 ACKDT: Acknowledge Data bit In I2C Master mode during Master Receive mode. The value that will be transmitted when the user initiates an Acknowledge sequence at the end of a receive. In I2C Slave mode when AHEN = 1 or DHEN = 1. The value that the Slave will transmit when it initiates an Acknowledge sequence at the end of an address or data reception. 1 = NACK is sent 0 = ACK is sent bit 4 ACKEN: Acknowledge Sequence Enable bit In I2C Master mode only; applicable during Master Receive mode. 1 = Initiates Acknowledge sequence on SDAx and SCLx pins, and transmits ACKDT data bit 0 = Acknowledge sequence is Idle bit 3 RCEN: Receive Enable bit (I2C Master mode only) 1 = Enables Receive mode for I2C; automatically cleared by hardware at end of 8-bit receive data byte 0 = Receive sequence is not in progress bit 2 PEN: Stop Condition Enable bit (I2C Master mode only) 1 = Initiates Stop condition on SDAx and SCLx pins 0 = Stop condition is Idle bit 1 RSEN: Restart Condition Enable bit (I2C Master mode only) 1 = Initiates Restart condition on SDAx and SCLx pins 0 = Restart condition is Idle bit 0 SEN: Start Condition Enable bit (I2C Master mode only) 1 = Initiates Start condition on SDAx and SCLx pins 0 = Start condition is Idle Note 1: 2: Automatically cleared to ‘0’ at the beginning of Slave transmission; automatically cleared to ‘0’ at the end of Slave reception. Automatically cleared to ‘0’ at the beginning of Slave transmission. DS70005319D-page 626  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 15-2: I2CxCONH: I2Cx CONTROL REGISTER HIGH U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — PCIE SCIE BOEN SDAHT SBCDE AHEN DHEN bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-7 Unimplemented: Read as ‘0’ bit 6 PCIE: Stop Condition Interrupt Enable bit (I2C Slave mode only). 1 = Enables interrupt on detection of Stop condition 0 = Stop detection interrupts are disabled bit 5 SCIE: Start Condition Interrupt Enable bit (I2C Slave mode only) 1 = Enables interrupt on detection of Start or Restart conditions 0 = Start detection interrupts are disabled bit 4 BOEN: Buffer Overwrite Enable bit (I2C Slave mode only) 1 = I2CxRCV is updated and an ACK is generated for a received address/data byte, ignoring the state of the I2COV bit only if RBF bit = 0 0 = I2CxRCV is only updated when I2COV is clear bit 3 SDAHT: SDAx Hold Time Selection bit 1 = Minimum of 300 ns hold time on SDAx after the falling edge of SCLx 0 = Minimum of 100 ns hold time on SDAx after the falling edge of SCLx bit 2 SBCDE: Slave Mode Bus Collision Detect Enable bit (I2C Slave mode only) If, on the rising edge of SCLx, SDAx is sampled low when the module is outputting a high state, the BCL bit is set and the bus goes Idle. This Detection mode is only valid during data and ACK transmit sequences. 1 = Enables Slave bus collision interrupts 0 = Slave bus collision interrupts are disabled bit 1 AHEN: Address Hold Enable bit (I2C Slave mode only) 1 = Following the 8th falling edge of SCLx for a matching received address byte; SCLREL bit (I2CxCONL[12]) will be cleared and the SCLx will be held low 0 = Address holding is disabled bit 0 DHEN: Data Hold Enable bit (I2C Slave mode only) 1 = Following the 8th falling edge of SCLx for a received data byte; Slave hardware clears the SCLREL bit (I2CxCONL[12]) and SCLx is held low 0 = Data holding is disabled  2017-2019 Microchip Technology Inc. DS70005319D-page 627 dsPIC33CH128MP508 FAMILY REGISTER 15-3: I2CxSTAT: I2Cx STATUS REGISTER HSC/R-0 HSC/R-0 HSC/R-0 U-0 U-0 HSC/R/C-0 HSC/R-0 HSC/R-0 ACKSTAT TRSTAT ACKTIM — — BCL GCSTAT ADD10 bit 15 HS/R/C-0 bit 8 HS/R/C-0 IWCOL I2COV HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 D/A P S R/W RBF TBF bit 7 bit 0 Legend: C = Clearable bit HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared HS = Hardware Settable bit bit 15 ACKSTAT: Acknowledge Status bit (updated in all Master and Slave modes) 1 = Acknowledge was not received from Slave 0 = Acknowledge was received from Slave bit 14 TRSTAT: Transmit Status bit (when operating as I2C Master; applicable to Master transmit operation) 1 = Master transmit is in progress (8 bits + ACK) 0 = Master transmit is not in progress bit 13 ACKTIM: Acknowledge Time Status bit (valid in I2C Slave mode only) 1 = Indicates I2C bus is in an Acknowledge sequence, set on 8th falling edge of SCLx clock 0 = Not an Acknowledge sequence, cleared on 9th rising edge of SCLx clock bit 12-11 Unimplemented: Read as ‘0’ bit 10 BCL: Bus Collision Detect bit (Master/Slave mode; cleared when I2C module is disabled, I2CEN = 0) 1 = A bus collision has been detected during a Master or Slave transmit operation 0 = No bus collision has been detected bit 9 GCSTAT: General Call Status bit (cleared after Stop detection) 1 = General call address was received 0 = General call address was not received bit 8 ADD10: 10-Bit Address Status bit (cleared after Stop detection) 1 = 10-bit address was matched 0 = 10-bit address was not matched bit 7 IWCOL: I2Cx Write Collision Detect bit 1 = An attempt to write to the I2CxTRN register failed because the I2C module is busy; must be cleared in software 0 = No collision bit 6 I2COV: I2Cx Receive Overflow Flag bit 1 = A byte was received while the I2CxRCV register is still holding the previous byte; I2COV is a “don’t care” in Transmit mode, must be cleared in software 0 = No overflow bit 5 D/A: Data/Address bit (when operating as I2C Slave) 1 = Indicates that the last byte received was data 0 = Indicates that the last byte received or transmitted was an address bit 4 P: I2Cx Stop bit Updated when Start, Reset or Stop is detected; cleared when the I2C module is disabled, I2CEN = 0. 1 = Indicates that a Stop bit has been detected last 0 = Stop bit was not detected last DS70005319D-page 628  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 15-3: I2CxSTAT: I2Cx STATUS REGISTER (CONTINUED) bit 3 S: I2Cx Start bit Updated when Start, Reset or Stop is detected; cleared when the I2C module is disabled, I2CEN = 0. 1 = Indicates that a Start (or Repeated Start) bit has been detected last 0 = Start bit was not detected last bit 2 R/W: Read/Write Information bit (when operating as I2C Slave) 1 = Read: Indicates the data transfer is output from the Slave 0 = Write: Indicates the data transfer is input to the Slave bit 1 RBF: Receive Buffer Full Status bit 1 = Receive is complete, I2CxRCV is full 0 = Receive is not complete, I2CxRCV is empty bit 0 TBF: Transmit Buffer Full Status bit 1 = Transmit is in progress, I2CxTRN is full (eight bits of data) 0 = Transmit is complete, I2CxTRN is empty REGISTER 15-4: I2CxMSK: I2Cx SLAVE MODE ADDRESS MASK REGISTER U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — R/W-0 R/W-0 MSK[9:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 MSK[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-10 Unimplemented: Read as ‘0’ bit 9-0 MSK[9:0]: I2Cx Mask for Address Bit x Select bits 1 = Enables masking for bit x of the incoming message address; bit match is not required in this position 0 = Disables masking for bit x; bit match is required in this position  2017-2019 Microchip Technology Inc. DS70005319D-page 629 dsPIC33CH128MP508 FAMILY NOTES: DS70005319D-page 630  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 16.0 SINGLE-EDGE NIBBLE TRANSMISSION (SENT) Note 1: This data sheet summarizes the features of this group of dsPIC33CH128MP508 family devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “Single-Edge Nibble Transmission (SENT) Module” (www.microchip.com/DS70005145) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 3.2 “Master Memory Organization” in this data sheet for device-specific register and bit information. 3: This SENT module is available only on the Master. Table 16-1 shows an overview of the SENT module. TABLE 16-1: SENT MODULE OVERVIEW Number of SENT Modules Identical (Modules) Master Core 2 Yes Slave Core None NA 16.1 SENT protocol timing is based on a predetermined time unit, TTICK. Both the transmitter and receiver must be preconfigured for TTICK, which can vary from 3 to 90 µs. A SENT message frame starts with a Sync pulse. The purpose of the Sync pulse is to allow the receiver to calculate the data rate of the message encoded by the transmitter. The SENT specification allows messages to be validated with up to a 20% variation in TTICK. This allows for the transmitter and receiver to run from different clocks that may be inaccurate, and drift with time and temperature. The data nibbles are four bits in length and are encoded as the data value + 12 ticks. This yields a 0 value of 12 ticks and the maximum value, 0xF, of 27 ticks. A SENT message consists of the following: • A synchronization/calibration period of 56 tick times • A status nibble of 12-27 tick times • Up to six data nibbles of 12-27 tick times • A CRC nibble of 12-27 tick times • An optional pause pulse period of 12-768 tick times Figure 16-1 shows a block diagram of the SENTx module. Figure 16-2 shows the construction of a typical 6-nibble data frame, with the numbers representing the minimum or maximum number of tick times for each section. Module Introduction The Single-Edge Nibble Transmission (SENT) module is based on the SAE J2716, “SENT – Single-Edge Nibble Transmission for Automotive Applications”. The SENT protocol is a one-way, single wire time modulated serial communication, based on successive falling edges. It is intended for use in applications where high-resolution sensor data need to be communicated from a sensor to an Engine Control Unit (ECU). The SENTx module has the following major features: • • • • • • • • • Selectable Transmit or Receive mode Synchronous or Asynchronous Transmit modes Automatic Data Rate Synchronization Optional Automatic Detection of CRC Errors in Receive mode Optional Hardware Calculation of CRC in Transmit mode Support for Optional Pause Pulse Period Data Buffering for One Message Frame Selectable Data Length for Transmit/Receive from Three to Six Nibbles Automatic Detection of Framing Errors  2017-2019 Microchip Technology Inc. DS70005319D-page 631 dsPIC33CH128MP508 FAMILY FIGURE 16-1: SENTx MODULE BLOCK DIAGRAM SENTx TX SENTxCON1 SENTxSTAT SENTxCON2 SENTxSYNC SENTxCON3 SENTxDATH/L SENTx Edge Control Output Driver Nibble Period Detector Tick Period Generator Edge Timing Edge Detect Sync Period Detector Control and Error Detection SENTx RX Legend: FIGURE 16-2: Receiver Only Transmitter Only Shared SENTx PROTOCOL DATA FRAMES Sync Period Status Data 1 Data 2 Data 3 Data 4 Data 5 Data 6 CRC Pause (optional) 56 12-27 12-27 12-27 12-27 12-27 12-27 12-27 12-27 12-768 DS70005319D-page 632  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 16.2 Transmit Mode 16.2.1 By default, the SENTx module is configured for transmit operation. The module can be configured for continuous asynchronous message frame transmission, or alternatively, for Synchronous mode triggered by software. When enabled, the transmitter will send a Sync, followed by the appropriate number of data nibbles, an optional CRC and optional pause pulse. The tick period used by the SENTx transmitter is set by writing a value to the TICKTIME[15:0] (SENTxCON2[15:0]) bits. The tick period calculations are shown in Equation 16-1. EQUATION 16-1: TICK PERIOD CALCULATION TICKTIME[15:0] = TTICK –1 TCLK An optional pause pulse can be used in Asynchronous mode to provide a fixed message frame time period. The frame period used by the SENTx transmitter is set by writing a value to the FRAMETIME[15:0] (SENTxCON3[15:0]) bits. The formulas used to calculate the value of frame time are shown in Equation 16-2. EQUATION 16-2: FRAME TIME CALCULATIONS FRAMETIME[15:0] = TTICK/TFRAME FRAMETIME[15:0]  122 + 27N FRAMETIME[15:0]  848 + 12N 16.2.1.1 TRANSMIT MODE CONFIGURATION Initializing the SENTx Module Perform the following steps to initialize the module: 1. Write RCVEN (SENTxCON1[11]) = 0 for Transmit mode. 2. Write TXM (SENTxCON1[10]) = 0 for Asynchronous Transmit mode or TXM = 1 for Synchronous mode. 3. Write NIBCNT[2:0] (SENTxCON1[2:0]) for the desired data frame length. 4. Write CRCEN (SENTxCON1[8]) for hardware or software CRC calculation. 5. Write PPP (SENTxCON1[7]) for optional pause pulse. 6. If PPP = 1, write TFRAME to SENTxCON3. 7. Write SENTxCON2 with the appropriate value for the desired tick period. 8. Enable interrupts and set interrupt priority. 9. Write initial status and data values to SENTxDATH/L. 10. If CRCEN = 0, calculate CRC and write the value to CRC[3:0] (SENTxDATL[3:0]). 11. Set the SNTEN (SENTxCON1[15]) bit to enable the module. User software updates to SENTxDATH/L must be performed after the completion of the CRC and before the next message frame’s status nibble. The recommended method is to use the message frame completion interrupt to trigger data writes. Where: TFRAME = Total time of the message from ms N = The number of data nibbles in message, 1-6 Note: The module will not produce a pause period with less than 12 ticks, regardless of the FRAMETIME[15:0] value. FRAMETIME[15:0] values beyond 2047 will have no effect on the length of a data frame.  2017-2019 Microchip Technology Inc. DS70005319D-page 633 dsPIC33CH128MP508 FAMILY 16.3 Receive Mode 16.3.1 The module can be configured for receive operation by setting the RCVEN (SENTxCON1[11]) bit. The time between each falling edge is compared to SYNCMIN[15:0] (SENTxCON3[15:0]) and SYNCMAX[15:0] (SENTxCON2[15:0]), and if the measured time lies between the minimum and maximum limits, the module begins to receive data. The validated Sync time is captured in the SENTxSYNC register and the tick time is calculated. Subsequent falling edges are verified to be within the valid data width and the data are stored in the SENTxDATL/H registers. An interrupt event is generated at the completion of the message and the user software should read the SENTx Data registers before the reception of the next nibble. The equation for SYNCMIN[15:0] and SYNCMAX[15:0] is shown in Equation 16-3. EQUATION 16-3: 16.3.1.1 Initializing the SENTx Module Perform the following steps to initialize the module: 1. 2. 3. 4. 5. 6. 7. 8. SYNCMIN[15:0] AND SYNCMAX[15:0] CALCULATIONS RECEIVE MODE CONFIGURATION Write RCVEN (SENTxCON1[11]) = 1 for Receive mode. Write NIBCNT[2:0] (SENTxCON1[2:0]) for the desired data frame length. Write CRCEN (SENTxCON1[8]) for hardware or software CRC validation. Write PPP (SENTxCON1[7]) = 1 if pause pulse is present. Write SENTxCON2 with the value of SYNCMAXx (Nominal Sync Period + 20%). Write SENTxCON3 with the value of SYNCMINx (Nominal Sync Period – 20%). Enable interrupts and set interrupt priority. Set the SNTEN (SENTxCON1[15]) bit to enable the module. The data should be read from the SENTxDATL/H registers after the completion of the CRC and before the next message frame’s status nibble. The recommended method is to use the message frame completion interrupt trigger. TTICK = TCLK • (TICKTIME[15:0] + 1) FRAMETIME[15:0] = TTICK/TFRAME SyncCount = 8 x FRCV x TTICK SYNCMIN[15:0] = 0.8 x SyncCount SYNCMAX[15:0] = 1.2 x SyncCount FRAMETIME[15:0]  122 + 27N FRAMETIME[15:0]  848 + 12N Where: TFRAME = Total time of the message from ms N = The number of data nibbles in message, 1-6 FRCV = FCY x Prescaler TCLK = FCY/Prescaler For TTICK = 3.0 µs SYNCMIN[15:0] = 76. Note: and FCLK = 4 MHz, To ensure a Sync period can be identified, the value written to SYNCMIN[15:0] must be less than the value written to SYNCMAX[15:0]. DS70005319D-page 634  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 16.4 SENT Control/Status Registers REGISTER 16-1: SENTxCON1: SENTx CONTROL REGISTER 1 R/W-0 U-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 SNTEN — SNTSIDL — RCVEN TXM(1) TXPOL(1) CRCEN bit 15 bit 8 R/W-0 R/W-0 U-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 PPP SPCEN(2) — PS — NIBCNT2 NIBCNT1 NIBCNT0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 SNTEN: SENTx Enable bit 1 = SENTx is enabled 0 = SENTx is disabled bit 14 Unimplemented: Read as ‘0’ bit 13 SNTSIDL: SENTx Stop in Idle Mode bit 1 = Discontinues module operation when the device enters Idle mode 0 = Continues module operation in Idle mode bit 12 Unimplemented: Read as ‘0’ bit 11 RCVEN: SENTx Receive Enable bit 1 = SENTx operates as a receiver 0 = SENTx operates as a transmitter (sensor) bit 10 TXM: SENTx Transmit Mode bit(1) 1 = SENTx transmits data frame only when triggered using the SYNCTXEN status bit 0 = SENTx transmits data frames continuously while SNTEN = 1 bit 9 TXPOL: SENTx Transmit Polarity bit(1) 1 = SENTx data output pin is low in the Idle state 0 = SENTx data output pin is high in the Idle state bit 8 CRCEN: CRC Enable bit Module in Receive Mode (RCVEN = 1): 1 = SENTx performs CRC verification on received data using the preferred J2716 method 0 = SENTx does not perform CRC verification on received data Module in Transmit Mode (RCVEN = 1): 1 = SENTx automatically calculates CRC using the preferred J2716 method 0 = SENTx does not calculate CRC bit 7 PPP: Pause Pulse Present bit 1 = SENTx is configured to transmit/receive SENT messages with pause pulse 0 = SENTx is configured to transmit/receive SENT messages without pause pulse bit 6 SPCEN: Short PWM Code Enable bit(2) 1 = SPC control from external source is enabled 0 = SPC control from external source is disabled bit 5 Unimplemented: Read as ‘0’ Note 1: 2: This bit has no function in Receive mode (RCVEN = 1). This bit has no function in Transmit mode (RCVEN = 0).  2017-2019 Microchip Technology Inc. DS70005319D-page 635 dsPIC33CH128MP508 FAMILY REGISTER 16-1: SENTxCON1: SENTx CONTROL REGISTER 1 (CONTINUED) bit 4 PS: SENTx Module Clock Prescaler (divider) bits 1 = Divide-by-4 0 = Divide-by-1 bit 3 Unimplemented: Read as ‘0’ bit 2-0 NIBCNT[2:0]: Nibble Count Control bits 111 = Reserved; do not use 110 = Module transmits/receives six data nibbles in a SENT data pocket 101 = Module transmits/receives five data nibbles in a SENT data pocket 100 = Module transmits/receives four data nibbles in a SENT data pocket 011 = Module transmits/receives three data nibbles in a SENT data pocket 010 = Module transmits/receives two data nibbles in a SENT data pocket 001 = Module transmits/receives one data nibble in a SENT data pocket 000 = Reserved; do not use Note 1: 2: This bit has no function in Receive mode (RCVEN = 1). This bit has no function in Transmit mode (RCVEN = 0). DS70005319D-page 636  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 16-2: SENTxSTAT: SENTx STATUS REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R-0 R-0 R-0 R-0 R/C-0 R/C-0 R-0 HC/R/W-0 PAUSE NIB2 NIB1 NIB0 CRCERR FRMERR RXIDLE SYNCTXEN(1) bit 7 bit 0 Legend: C = Clearable bit HC = Hardware Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7 PAUSE: Pause Period Status bit 1 = The module is transmitting/receiving a pause period 0 = The module is not transmitting/receiving a pause period bit 6-4 NIB[2:0]: Nibble Status bits Module in Transmit Mode (RCVEN = 0): 111 = Module is transmitting a CRC nibble 110 = Module is transmitting Data Nibble 6 101 = Module is transmitting Data Nibble 5 100 = Module is transmitting Data Nibble 4 011 = Module is transmitting Data Nibble 3 010 = Module is transmitting Data Nibble 2 001 = Module is transmitting Data Nibble 1 000 = Module is transmitting a status nibble or pause period, or is not transmitting Module in Receive Mode (RCVEN = 1): 111 = Module is receiving a CRC nibble or was receiving this nibble when an error occurred 110 = Module is receiving Data Nibble 6 or was receiving this nibble when an error occurred 101 = Module is receiving Data Nibble 5 or was receiving this nibble when an error occurred 100 = Module is receiving Data Nibble 4 or was receiving this nibble when an error occurred 011 = Module is receiving Data Nibble 3 or was receiving this nibble when an error occurred 010 = Module is receiving Data Nibble 2 or was receiving this nibble when an error occurred 001 = Module is receiving Data Nibble 1 or was receiving this nibble when an error occurred 000 = Module is receiving a status nibble or waiting for Sync bit 3 CRCERR: CRC Status bit (Receive mode only) 1 = A CRC error has occurred for the 1-6 data nibbles in SENTxDATL/H 0 = A CRC error has not occurred bit 2 FRMERR: Framing Error Status bit (Receive mode only) 1 = A data nibble was received with less than 12 tick periods or greater than 27 tick periods 0 = Framing error has not occurred bit 1 RXIDLE: SENTx Receiver Idle Status bit (Receive mode only) 1 = The SENTx data bus has been Idle (high) for a period of SYNCMAX[15:0] or greater 0 = The SENTx data bus is not Idle Note 1: In Receive mode (RCVEN = 1), the SYNCTXEN bit is read-only.  2017-2019 Microchip Technology Inc. DS70005319D-page 637 dsPIC33CH128MP508 FAMILY REGISTER 16-2: bit 0 Note 1: SENTxSTAT: SENTx STATUS REGISTER (CONTINUED) SYNCTXEN: SENTx Synchronization Period Status/Transmit Enable bit(1) Module in Receive Mode (RCVEN = 1): 1 = A valid synchronization period was detected; the module is receiving nibble data 0 = No synchronization period has been detected; the module is not receiving nibble data Module in Asynchronous Transmit Mode (RCVEN = 0, TXM = 0): The bit always reads as ‘1’ when the module is enabled, indicating the module transmits SENTx data frames continuously. The bit reads ‘0’ when the module is disabled. Module in Synchronous Transmit Mode (RCVEN = 0, TXM = 1): 1 = The module is transmitting a SENTx data frame 0 = The module is not transmitting a data frame, user software may set SYNCTXEN to start another data frame transmission In Receive mode (RCVEN = 1), the SYNCTXEN bit is read-only. DS70005319D-page 638  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 16-3: R/W-0 SENTxDATL: SENTx RECEIVE DATA REGISTER LOW(1) R/W-0 R/W-0 R/W-0 R/W-0 DATA4[3:0] R/W-0 R/W-0 R/W-0 DATA5[3:0] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DATA6[3:0] R/W-0 R/W-0 R/W-0 CRC[3:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-12 DATA4[3:0]: Data Nibble 4 Data bits bit 11-8 DATA5[3:0]: Data Nibble 5 Data bits bit 7-4 DATA6[3:0]: Data Nibble 6 Data bits bit 3-0 CRC[3:0]: CRC Nibble Data bits Note 1: x = Bit is unknown Register bits are read-only in Receive mode (RCVEN = 1). In Transmit mode, the CRC[3:0] bits are read-only when automatic CRC calculation is enabled (RCVEN = 0, CRCEN = 1). REGISTER 16-4: R/W-0 SENTxDATH: SENTx RECEIVE DATA REGISTER HIGH(1) R/W-0 R/W-0 R/W-0 R/W-0 STAT[3:0] R/W-0 R/W-0 R/W-0 DATA1[3:0] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DATA2[3:0] R/W-0 R/W-0 R/W-0 DATA3[3:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-12 STAT[3:0]: Status Nibble Data bits bit 11-8 DATA1[3:0]: Data Nibble 1 Data bits bit 7-4 DATA2[3:0]: Data Nibble 2 Data bits bit 3-0 DATA3[3:0]: Data Nibble 3 Data bits Note 1: x = Bit is unknown Register bits are read-only in Receive mode (RCVEN = 1). In Transmit mode, the CRC[3:0] bits are read-only when automatic CRC calculation is enabled (RCVEN = 0, CRCEN = 1).  2017-2019 Microchip Technology Inc. DS70005319D-page 639 dsPIC33CH128MP508 FAMILY NOTES: DS70005319D-page 640  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 17.0 TIMER1 The Timer1 module has the following unique features over other timers: Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “Timer1 Module” (www.microchip.com/DS70005279) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). • • • • Can be Operated in Asynchronous Counter mode Asynchronous Timer Operational during CPU Sleep mode Software Selectable Prescalers 1:1, 1:8, 1:64 and 1:256 • External Clock Selection Control • The Timer1 External Clock Input (T1CK) can Optionally be Synchronized to the Internal Device Clock and the Clock Synchronization is Performed after the Prescaler 2: The timer is identical for both Master core and Slave core. The x is common for both Master core and Slave core (where the x represents the number of the specific module being addressed). If Timer1 is used for SCCP, the timer should be running in Synchronous mode. The Timer1 module can operate in one of the following modes: 3: All associated register names are the same on the Master core and the Slave core. The Slave code will be developed in a separate project in MPLAB® X IDE with the device selection, dsPIC33CH128MP508S1, where S1 indicates the Slave device. • • • • Timer mode Gated Timer mode Synchronous Counter mode Asynchronous Counter mode Table 17-1 shows an overview of the Timer1 module. TABLE 17-1: The Timer1 module is a 16-bit timer that can operate as a free-running interval timer/counter. TIMER1 MODULE OVERVIEW Number of Timer1 Modules Identical (Modules) Master Core 1 Yes Slave Core 1 Yes A block diagram of Timer1 is shown in Figure 17-1. 2 TCY FRC 0 TCY TGATE 1 Sync 0 2 3 00 01 Prescaler tmr_clk TMRx TGATE TCY TCS TGATE T1CK (External Clock) 16-BIT TIMER1 MODULE BLOCK DIAGRAM TECS[1:0] FIGURE 17-1: Comparator 0 10 1 11 2 TCKPS[1:0] Timer 1 Interrupt PRx TGATE  2017-2019 Microchip Technology Inc. DS70005319D-page 641 dsPIC33CH128MP508 FAMILY 17.1 Timer1 Control Register REGISTER 17-1: T1CON: TIMER1 CONTROL REGISTER R/W-0 U-0 R/W-0 R/W-0 R-0 R-0 R/W-0 R/W-0 TON(1) — SIDL TMWDIS TMWIP PRWIP TECS1 TECS0 bit 15 bit 8 R/W-0 U-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 U-0 TGATE — TCKPS1 TCKPS0 — TSYNC(1) TCS(1) — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 TON: Timer1 On bit(1) 1 = Starts 16-bit Timer1 0 = Stops 16-bit Timer1 bit 14 Unimplemented: Read as ‘0’ bit 13 SIDL: Timer1 Stop in Idle Mode bit 1 = Discontinues module operation when device enters Idle mode 0 = Continues module operation in Idle mode bit 12 TMWDIS: Asynchronous Timer1 Write Disable bit 1 = Timer writes are ignored while a posted write to TMR1 or PR1 is synchronized to the asynchronous clock domain 0 = Back-to-back writes are enabled in Asynchronous mode bit 11 TMWIP: Asynchronous Timer1 Write in Progress bit 1 = Write to the timer in Asynchronous mode is pending 0 = Write to the timer in Asynchronous mode is complete bit 10 PRWIP: Asynchronous Period Write in Progress bit 1 = Write to the Period register in Asynchronous mode is pending 0 = Write to the Period register in Asynchronous mode is complete bit 9-8 TECS[1:0]: Timer1 Extended Clock Select bits 11 = FRC clock 10 = 2 TCY 01 = TCY 00 = External Clock comes from the T1CK pin bit 7 TGATE: Timer1 Gated Time Accumulation Enable bit When TCS = 1: This bit is ignored. When TCS = 0: 1 = Gated time accumulation is enabled 0 = Gated time accumulation is disabled bit 6 Unimplemented: Read as ‘0’ Note 1: When Timer1 is enabled in External Synchronous Counter mode (TCS = 1, TSYNC = 1, TON = 1), any attempts by user software to write to the TMR1 register are ignored. DS70005319D-page 642  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 17-1: T1CON: TIMER1 CONTROL REGISTER (CONTINUED) bit 5-4 TCKPS[1:0]: Timer1 Input Clock Prescale Select bits 11 = 1:256 10 = 1:64 01 = 1:8 00 = 1:1 bit 3 Unimplemented: Read as ‘0’ bit 2 TSYNC: Timer1 External Clock Input Synchronization Select bit(1) When TCS = 1: 1 = Synchronizes the External Clock input 0 = Does not synchronize the External Clock input When TCS = 0: This bit is ignored. bit 1 TCS: Timer1 Clock Source Select bit(1) 1 = External Clock source selected by TECS[1:0] 0 = Internal peripheral clock (FP) bit 0 Unimplemented: Read as ‘0’ Note 1: When Timer1 is enabled in External Synchronous Counter mode (TCS = 1, TSYNC = 1, TON = 1), any attempts by user software to write to the TMR1 register are ignored.  2017-2019 Microchip Technology Inc. DS70005319D-page 643 dsPIC33CH128MP508 FAMILY NOTES: DS70005319D-page 644  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 18.0 CONFIGURABLE LOGIC CELL (CLC) Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. For more information, refer to “Configurable Logic Cell (CLC)” (www.microchip.com/DS70005298) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). The information in this data sheet supersedes the information in the FRM. 2: The CLC is identical for both Master core and Slave core (where the x represents the number of the specific module being addressed in Master or Slave). 3: All associated register names are the same on the Master core and the Slave core. The Slave code will be developed in a separate project in MPLAB® X IDE with the device selection, dsPIC33CH128MP508S1, where the S1 indicates the Slave device. The Master and Slave are CLC1 and CLC2. FIGURE 18-1: The Configurable Logic Cell (CLC) module allows the user to specify combinations of signals as inputs to a logic function and to use the logic output to control other peripherals or I/O pins. This provides greater flexibility and potential in embedded designs, since the CLC module can operate outside the limitations of software execution, and supports a vast amount of output designs. There are four input gates to the selected logic function. These four input gates select from a pool of up to 32 signals that are selected using four data source selection multiplexers. Table 18-1 shows an overview of the module. TABLE 18-1: CLC MODULE OVERVIEW Number of CLC Modules Master 4 Yes Slave 4 Yes Figure 18-3 shows the details of the data source multiplexers and Figure 18-2 shows the logic input gate connections. CLCx MODULE DS1[2:0] DS2[2:0] DS3[2:0] DS4[2:0] G1POL G2POL G3POL G4POL D FCY MODE[2:0] CLC Inputs (32) Identical (Modules) Gate 2 Logic Gate 3 Function Gate 4 CLK TRISx Control CLCx Output CLCx Logic Output See Figure 18-2 LCOUT LCOE LCEN Gate 1 Input Data Selection Gates Q LCPOL Interrupt det See Figure 18-3 INTP Set CLCxIF INTN Interrupt det  2017-2019 Microchip Technology Inc. DS70005319D-page 645 dsPIC33CH128MP508 FAMILY FIGURE 18-2: CLCx LOGIC FUNCTION COMBINATORIAL OPTIONS AND – OR OR – XOR Gate 1 Gate 1 Gate 2 Logic Output Gate 3 Gate 2 Logic Output Gate 3 Gate 4 Gate 4 MODE[2:0] = 000 MODE[2:0] = 001 4-Input AND S-R Latch Gate 1 Gate 1 Gate 2 Gate 2 Logic Output Gate 3 Gate 4 S Gate 3 Q R Gate 4 MODE[2:0] = 010 MODE[2:0] = 011 1-Input D Flip-Flop with S and R 2-Input D Flip-Flop with R Gate 4 D Gate 2 S Gate 4 Q Logic Output D Gate 2 Gate 1 Gate 1 Logic Output Q Logic Output R R Gate 3 Gate 3 MODE[2:0] = 100 MODE[2:0] = 101 J-K Flip-Flop with R 1-Input Transparent Latch with S and R Gate 4 Gate 2 J Q Logic Output Gate 1 K Gate 4 R Gate 2 D Gate 1 LE Gate 3 S Q Logic Output R Gate 3 MODE[2:0] = 110 DS70005319D-page 646 MODE[2:0] = 111  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY CLCx INPUT SOURCE SELECTION DIAGRAM(1,2) FIGURE 18-3: Data Selection Input 0 Input 1 Input 2 Input 3 Input 4 Input 5 Input 6 Input 7 000 Data Gate 1 Data 1 Noninverted Data 1 Inverted 111 DS1x (CLCxSEL[2:0]) G1D1T G1D1N G1D2T G1D2N Input 8 Input 9 Input 10 Input 11 Input 12 Input 13 Input 14 Input 15 G1D3T Data 2 Noninverted Data 2 Inverted G1D4T 000 G1D4N Data Gate 2 Data 3 Noninverted Data 3 Inverted Gate 2 (Same as Data Gate 1) Data Gate 3 111 Gate 3 DS3x (CLCxSEL[10:8]) Input 24 Input 25 Input 26 Input 27 Input 28 Input 29 Input 30 Input 31 G1D3N G1POL (CLCxCONH[0]) 111 DS2x (CLCxSEL[6:4]) Input 16 Input 17 Input 18 Input 19 Input 20 Input 21 Input 22 Input 23 Gate 1 000 (Same as Data Gate 1) Data Gate 4 000 Gate 4 Data 4 Noninverted (Same as Data Gate 1) Data 4 Inverted 111 DS4x (CLCxSEL[14:12]) Note 1: 2: All controls are undefined at power-up. CLC that have unused/unassigned inputs are a logic ‘0’, and through polarity control, they can be changed to a ‘1’.  2017-2019 Microchip Technology Inc. DS70005319D-page 647 dsPIC33CH128MP508 FAMILY 18.1 Control Registers The CLCx Input MUX Select register (CLCxSEL) allows the user to select up to four data input sources using the four data input selection multiplexers. Each multiplexer has a list of eight data sources available. The CLCx module is controlled by the following registers: • • • • • CLCxCONL CLCxCONH CLCxSEL CLCxGLSL CLCxGLSH The CLCx Gate Logic Input Select registers (CLCxGLSL and CLCxGLSH) allow the user to select which outputs from each of the selection MUXes are used as inputs to the input gates of the logic cell. Each data source MUX outputs both a true and a negated version of its output. All of these eight signals are enabled, ORed together by the logic cell input gates. The CLCx Control registers (CLCxCONL and CLCxCONH) are used to enable the module and interrupts, control the output enable bit, select output polarity and select the logic function. The CLCx Control registers also allow the user to control the logic polarity of not only the cell output, but also some intermediate variables. REGISTER 18-1: If no gate inputs are selected, the input to the gate will be zero or one, depending on the GxPOL bits. CLCxCONL: CLCx CONTROL REGISTER (LOW) R/W-0 U-0 U-0 U-0 R/W-0 R/W-0 U-0 U-0 LCEN — — — INTP INTN — — bit 15 bit 8 R-0 R-0 R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0 LCOE LCOUT LCPOL — — MODE2 MODE1 MODE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 LCEN: CLCx Enable bit 1 = CLCx is enabled and mixing input signals 0 = CLCx is disabled and has logic zero outputs bit 14-12 Unimplemented: Read as ‘0’ bit 11 INTP: CLCx Positive Edge Interrupt Enable bit 1 = Interrupt will be generated when a rising edge occurs on LCOUT 0 = Interrupt will not be generated bit 10 INTN: CLCx Negative Edge Interrupt Enable bit 1 = Interrupt will be generated when a falling edge occurs on LCOUT 0 = Interrupt will not be generated bit 9-8 Unimplemented: Read as ‘0’ bit 7 LCOE: CLCx Port Enable bit 1 = CLCx port pin output is enabled 0 = CLCx port pin output is disabled bit 6 LCOUT: CLCx Data Output Status bit 1 = CLCx output high 0 = CLCx output low bit 5 LCPOL: CLCx Output Polarity Control bit 1 = The output of the module is inverted 0 = The output of the module is not inverted bit 4-3 Unimplemented: Read as ‘0’ DS70005319D-page 648  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 18-1: bit 2-0 CLCxCONL: CLCx CONTROL REGISTER (LOW) (CONTINUED) MODE[2:0]: CLCx Mode bits 111 = Single input transparent latch with S and R 110 = JK flip-flop with R 101 = Two-input D flip-flop with R 100 = Single input D flip-flop with S and R 011 = SR latch 010 = Four-input AND 001 = Four-input OR-XOR 000 = Four-input AND-OR REGISTER 18-2: CLCxCONH: CLCx CONTROL REGISTER (HIGH) U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — — G4POL G3POL G2POL G1POL bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-4 Unimplemented: Read as ‘0’ bit 3 G4POL: Gate 4 Polarity Control bit 1 = Channel 4 logic output is inverted when applied to the logic cell 0 = Channel 4 logic output is not inverted bit 2 G3POL: Gate 3 Polarity Control bit 1 = Channel 3 logic output is inverted when applied to the logic cell 0 = Channel 3 logic output is not inverted bit 1 G2POL: Gate 2 Polarity Control bit 1 = Channel 2 logic output is inverted when applied to the logic cell 0 = Channel 2 logic output is not inverted bit 0 G1POL: Gate 1 Polarity Control bit 1 = Channel 1 logic output is inverted when applied to the logic cell 0 = Channel 1 logic output is not inverted  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 649 dsPIC33CH128MP508 FAMILY REGISTER 18-3: U-0 CLCxSEL: CLCx INPUT MUX SELECT REGISTER R/W-0 — R/W-0 R/W-0 DS4[2:0] U-0 R/W-0 — R/W-0 R/W-0 DS3[2:0] bit 15 bit 8 U-0 R/W-0 — R/W-0 R/W-0 DS2[2:0] U-0 R/W-0 — R/W-0 R/W-0 DS1[2:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 Unimplemented: Read as ‘0’ bit 14-12 DS4[2:0]: Data Selection MUX 4 Signal Selection bits (Master) 111 = Master SCCP3 auxiliary out 110 = Master SCCP1 auxiliary out 101 = CLCIND RP pin 100 = Reserved 011 = Master SPI1 Input (SDIx)(1) 010 = Slave Comparator 2 out 001 = Master CLC2 output 000 = Master PWM event A x = Bit is unknown DS4[2:0]: Data Selection MUX 4 Signal Selection bits (Slave) 111 = Slave SCCP3 auxiliary out 110 = Slave SCCP1 auxiliary out 101 = Slave CLCIND 100 = Reserved 011 = Slave SPI1 Input (SDIx)(1) 010 = Slave Comparator 2 out 001 = Slave CLC2 out 000 = Slave PWM event bit 11 Unimplemented: Read as ‘0’ bit 10-8 DS3[2:0]: Data Selection MUX 3 Signal Selection bits (Master) 111 = Master SCCP4 Compare Event Flag (CCP4IF) 110 = Master SCCP3 Compare Event Flag (CCP3IF) 101 = CLC4 out 100 = Master UART1 RX output corresponding to CLCx module 011 = Master SPI1 Output (SDOx) corresponding to CLCx module 010 = Slave Comparator 1 output 001 = Master CLC1 output 000 = Master CLCINC I/O pin DS3[2:0]: Data Selection MUX 3 Signal Selection bits (Slave) 111 = Slave SCCP4 Compare Event Flag (CCP4IF) 110 = Slave SCCP3 Compare Event Flag (CCP3IF) 101 = Slave CLC4 out 100 = Slave UART1 RX output corresponding to CLCx module 011 = Slave SPI1 Output (SDOx) corresponding to CLCx module 010 = Slave Comparator 1 output 001 = Slave CLC1 output 000 = Slave CLCINC I/O pin Note 1: Valid only for the SPI with PPS selection. DS70005319D-page 650  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 18-3: CLCxSEL: CLCx INPUT MUX SELECT REGISTER (CONTINUED) bit 7 Unimplemented: Read as ‘0’ bit 6-4 DS2[2:0]: Data Selection MUX 2 Signal Selection bits (Master) 111 = Master SCCP2 OC (CCP2IF) out 110 = Master SCCP1 OC (CCP1IF) out 101 = Reserved 100 = Reserved 011 = Master UART1 TX input corresponding to CLCx module 010 = Master Comparator 1 output 001 = Slave CLC2 output 000 = Master CLCINB I/O pin DS2[2:0]: Data Selection MUX 2 Signal Selection bits (Slave) 111 = Slave SCCP2 OC (CCP2IF) out 110 = Slave SCCP1 OC (CCP1IF) out 101 = Reserved 100 = Reserved 011 = Slave UART1 TX input corresponding to CLCx module 010 = Master Comparator 1 output 001 = Master CLC2 output 000 = Slave CLCINB I/O pin bit 3 Unimplemented: Read as ‘0’ bit 2-0 DS1[2:0]: Data Selection MUX 1 Signal Selection bits (Master) 111 = Master SCCP4 auxiliary out 110 = Master SCCP2 auxiliary out 101 = Slave Comparator 3 100 = Master REFCLKO output 011 = Master INTRC/LPRC clock source 010 = CLC3 out 001 = Master system clock (FCY) 000 = Master CLCINA I/O pin DS1[2:0]: Data Selection MUX 1 Signal Selection bits (Slave) 111 = Slave SCCP4 auxiliary out 110 = Slave SCCP2 auxiliary out 101 = Slave Comparator 3 100 = Slave REFCLKO output 011 = Slave INTRC/LPRC clock source 010 = Slave CLC3 out 001 = Slave system clock (FCY) 000 = Slave CLCINA I/O pin Note 1: Valid only for the SPI with PPS selection.  2017-2019 Microchip Technology Inc. DS70005319D-page 651 dsPIC33CH128MP508 FAMILY REGISTER 18-4: CLCxGLSL: CLCx GATE LOGIC INPUT SELECT LOW REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 G2D4T G2D4N G2D3T G2D3N G2D2T G2D2N G2D1T G2D1N bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 G1D4T G1D4N G1D3T G1D3N G1D2T G1D2N G1D1T G1D1N bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 G2D4T: Gate 2 Data Source 4 True Enable bit 1 = Data Source 4 signal is enabled for Gate 2 0 = Data Source 4 signal is disabled for Gate 2 bit 14 G2D4N: Gate 2 Data Source 4 Negated Enable bit 1 = Data Source 4 inverted signal is enabled for Gate 2 0 = Data Source 4 inverted signal is disabled for Gate 2 bit 13 G2D3T: Gate 2 Data Source 3 True Enable bit 1 = Data Source 3 signal is enabled for Gate 2 0 = Data Source 3 signal is disabled for Gate 2 bit 12 G2D3N: Gate 2 Data Source 3 Negated Enable bit 1 = Data Source 3 inverted signal is enabled for Gate 2 0 = Data Source 3 inverted signal is disabled for Gate 2 bit 11 G2D2T: Gate 2 Data Source 2 True Enable bit 1 = Data Source 2 signal is enabled for Gate 2 0 = Data Source 2 signal is disabled for Gate 2 bit 10 G2D2N: Gate 2 Data Source 2 Negated Enable bit 1 = Data Source 2 inverted signal is enabled for Gate 2 0 = Data Source 2 inverted signal is disabled for Gate 2 bit 9 G2D1T: Gate 2 Data Source 1 True Enable bit 1 = Data Source 1 signal is enabled for Gate 2 0 = Data Source 1 signal is disabled for Gate 2 bit 8 G2D1N: Gate 2 Data Source 1 Negated Enable bit 1 = Data Source 1 inverted signal is enabled for Gate 2 0 = Data Source 1 inverted signal is disabled for Gate 2 bit 7 G1D4T: Gate 1 Data Source 4 True Enable bit 1 = Data Source 4 signal is enabled for Gate 1 0 = Data Source 4 signal is disabled for Gate 1 bit 6 G1D4N: Gate 1 Data Source 4 Negated Enable bit 1 = Data Source 4 inverted signal is enabled for Gate 1 0 = Data Source 4 inverted signal is disabled for Gate 1 bit 5 G1D3T: Gate 1 Data Source 3 True Enable bit 1 = Data Source 3 signal is enabled for Gate 1 0 = Data Source 3 signal is disabled for Gate 1 bit 4 G1D3N: Gate 1 Data Source 3 Negated Enable bit 1 = Data Source 3 inverted signal is enabled for Gate 1 0 = Data Source 3 inverted signal is disabled for Gate 1 DS70005319D-page 652 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 18-4: CLCxGLSL: CLCx GATE LOGIC INPUT SELECT LOW REGISTER (CONTINUED) bit 3 G1D2T: Gate 1 Data Source 2 True Enable bit 1 = Data Source 2 signal is enabled for Gate 1 0 = Data Source 2 signal is disabled for Gate 1 bit 2 G1D2N: Gate 1 Data Source 2 Negated Enable bit 1 = Data Source 2 inverted signal is enabled for Gate 1 0 = Data Source 2 inverted signal is disabled for Gate 1 bit 1 G1D1T: Gate 1 Data Source 1 True Enable bit 1 = Data Source 1 signal is enabled for Gate 1 0 = Data Source 1 signal is disabled for Gate 1 bit 0 G1D1N: Gate 1 Data Source 1 Negated Enable bit 1 = Data Source 1 inverted signal is enabled for Gate 1 0 = Data Source 1 inverted signal is disabled for Gate 1  2017-2019 Microchip Technology Inc. DS70005319D-page 653 dsPIC33CH128MP508 FAMILY REGISTER 18-5: CLCxGLSH: CLCx GATE LOGIC INPUT SELECT HIGH REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 G4D4T G4D4N G4D3T G4D3N G4D2T G4D2N G4D1T G4D1N bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 G3D4T G3D4N G3D3T G3D3N G3D2T G3D2N G3D1T G3D1N bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 G4D4T: Gate 4 Data Source 4 True Enable bit 1 = Data Source 4 signal is enabled for Gate 4 0 = Data Source 4 signal is disabled for Gate 4 bit 14 G4D4N: Gate 4 Data Source 4 Negated Enable bit 1 = Data Source 4 inverted signal is enabled for Gate 4 0 = Data Source 4 inverted signal is disabled for Gate 4 bit 13 G4D3T: Gate 4 Data Source 3 True Enable bit 1 = Data Source 3 signal is enabled for Gate 4 0 = Data Source 3 signal is disabled for Gate 4 bit 12 G4D3N: Gate 4 Data Source 3 Negated Enable bit 1 = Data Source 3 inverted signal is enabled for Gate 4 0 = Data Source 3 inverted signal is disabled for Gate 4 bit 11 G4D2T: Gate 4 Data Source 2 True Enable bit 1 = Data Source 2 signal is enabled for Gate 4 0 = Data Source 2 signal is disabled for Gate 4 bit 10 G4D2N: Gate 4 Data Source 2 Negated Enable bit 1 = Data Source 2 inverted signal is enabled for Gate 4 0 = Data Source 2 inverted signal is disabled for Gate 4 bit 9 G4D1T: Gate 4 Data Source 1 True Enable bit 1 = Data Source 1 signal is enabled for Gate 4 0 = Data Source 1 signal is disabled for Gate 4 bit 8 G4D1N: Gate 4 Data Source 1 Negated Enable bit 1 = Data Source 1 inverted signal is enabled for Gate 4 0 = Data Source 1 inverted signal is disabled for Gate 4 bit 7 G3D4T: Gate 3 Data Source 4 True Enable bit 1 = Data Source 4 signal is enabled for Gate 3 0 = Data Source 4 signal is disabled for Gate 3 bit 6 G3D4N: Gate 3 Data Source 4 Negated Enable bit 1 = Data Source 4 inverted signal is enabled for Gate 3 0 = Data Source 4 inverted signal is disabled for Gate 3 bit 5 G3D3T: Gate 3 Data Source 3 True Enable bit 1 = Data Source 3 signal is enabled for Gate 3 0 = Data Source 3 signal is disabled for Gate 3 bit 4 G3D3N: Gate 3 Data Source 3 Negated Enable bit 1 = Data Source 3 inverted signal is enabled for Gate 3 0 = Data Source 3 inverted signal is disabled for Gate 3 DS70005319D-page 654 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 18-5: CLCxGLSH: CLCx GATE LOGIC INPUT SELECT HIGH REGISTER (CONTINUED) bit 3 G3D2T: Gate 3 Data Source 2 True Enable bit 1 = Data Source 2 signal is enabled for Gate 3 0 = Data Source 2 signal is disabled for Gate 3 bit 2 G3D2N: Gate 3 Data Source 2 Negated Enable bit 1 = Data Source 2 inverted signal is enabled for Gate 3 0 = Data Source 2 inverted signal is disabled for Gate 3 bit 1 G3D1T: Gate 3 Data Source 1 True Enable bit 1 = Data Source 1 signal is enabled for Gate 3 0 = Data Source 1 signal is disabled for Gate 3 bit 0 G3D1N: Gate 3 Data Source 1 Negated Enable bit 1 = Data Source 1 inverted signal is enabled for Gate 3 0 = Data Source 1 inverted signal is disabled for Gate 3  2017-2019 Microchip Technology Inc. DS70005319D-page 655 dsPIC33CH128MP508 FAMILY NOTES: DS70005319D-page 656  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 19.0 32-BIT PROGRAMMABLE CYCLIC REDUNDANCY CHECK (CRC) GENERATOR The 32-bit programmable CRC generator provides a hardware implemented method of quickly generating checksums for various networking and security applications. It offers the following features: • User-Programmable CRC Polynomial Equation, up to 32 Bits • Programmable Shift Direction (little or big-endian) • Independent Data and Polynomial Lengths • Configurable Interrupt Output • Data FIFO Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. For more information, refer to “32-Bit Programmable Cyclic Redundancy Check (CRC)” (www.microchip.com/DS30009729) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). A simple version of the CRC shift engine is displayed in Figure 19-1. Table 19-1 displays a simplified block diagram of the CRC generator. 2: The CRC module is available only on the Master. FIGURE 19-1: TABLE 19-1: CRC MODULE OVERVIEW Number of CRC Modules Identical (Modules) Master Core 1 Yes Slave Core None NA CRC MODULE BLOCK DIAGRAM CRCDATH CRCDATL CRCISEL FIFO Empty Variable FIFO (4x32, 8x16 or 16x8) CRCWDATH CRCWDATL Shift Complete 1 CRC Interrupt 0 LENDIAN Shift Buffer 1 CRC Shift Engine 0 Shifter Clock 2 * FCY  2017-2019 Microchip Technology Inc. DS70005319D-page 657 dsPIC33CH128MP508 FAMILY 19.1 CRC Control Registers REGISTER 19-1: CRCCONL: CRC CONTROL REGISTER LOW R/W-0 U-0 R/W-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 HSC/R-0 CRCEN — CSIDL VWORD4 VWORD3 VWORD2 VWORD1 VWORD0 bit 15 bit 8 HSC/R-0 HSC/R-1 R/W-0 HC/R/W-0 R/W-0 R/W-0 U-0 U-0 CRCFUL CRCMPT CRCISEL CRCGO LENDIAN MOD — — bit 7 bit 0 Legend: HC = Hardware Clearable bit HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 CRCEN: CRC Enable bit 1 = Enables module 0 = Disables module bit 14 Unimplemented: Read as ‘0’ bit 13 CSIDL: CRC Stop in Idle Mode bit 1 = Discontinues module operation when device enters Idle mode 0 = Continues module operation in Idle mode bit 12-8 VWORD[4:0]: Pointer Value bits Indicates the number of valid words in the FIFO. Has a maximum value of 8 when PLEN[4:0]  7 or 16 when PLEN[4:0] 7. bit 7 CRCFUL: CRC FIFO Full bit 1 = FIFO is full 0 = FIFO is not full bit 6 CRCMPT: CRC FIFO Empty bit 1 = FIFO is empty 0 = FIFO is not empty bit 5 CRCISEL: CRC Interrupt Selection bit 1 = Interrupt on FIFO is empty; the final word of data is still shifting through the CRC 0 = Interrupt on shift is complete and results are ready bit 4 CRCGO: CRC Start bit 1 = Starts CRC serial shifter 0 = CRC serial shifter is turned off bit 3 LENDIAN: Data Shift Direction Select bit 1 = Data word is shifted into the FIFO, starting with the LSb (little-endian) 0 = Data word is shifted into the FIFO, starting with the MSb (big-endian) bit 2 MOD: CRC Calculation Mode bit 1 = Alternate mode 0 = Legacy mode bit bit 1-0 Unimplemented: Read as ‘0’ DS70005319D-page 658  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 19-2: CRCCONH: CRC CONTROL REGISTER HIGH U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DWIDTH[4:0] bit 15 bit 8 U-0 U-0 U-0 — — — R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PLEN[4:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-13 Unimplemented: Read as ‘0’ bit 12-8 DWIDTH[4:0]: Data Word Width Configuration bits Configures the width of the data word (Data Word Width – 1). bit 7-5 Unimplemented: Read as ‘0’ bit 4-0 PLEN[4:0]: Polynomial Length Configuration bits Configures the length of the polynomial (Polynomial Length – 1).  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 659 dsPIC33CH128MP508 FAMILY REGISTER 19-3: R/W-0 CRCXORL: CRC XOR POLYNOMIAL REGISTER, LOW BYTE R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 X[15:8] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 — X[7:1] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-1 X[15:1]: XOR of Polynomial Term xn Enable bits bit 0 Unimplemented: Read as ‘0’ REGISTER 19-4: R/W-0 x = Bit is unknown CRCXORH: CRC XOR POLYNOMIAL REGISTER, HIGH BYTE R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 X[31:24] bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 X[23:16] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown X[31:16]: XOR of Polynomial Term xn Enable bits DS70005319D-page 660  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 20.0 CURRENT BIAS GENERATOR (CBG) Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “Current Bias Generator (CBG)” (www.microchip.com/DS70005253) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 3.2 “Master Memory Organization” in this data sheet for device-specific register and bit information. TABLE 20-1: CBG CHANNEL AVAILABILITY Package ISRCx 28-pin — IBIASx IBIAS0, IBIAS1, IBIAS2 36-pin ISRC0, ISRC1 IBIAS0, IBIAS1, IBIAS2 48-pin ISRC0, ISRC1, ISRC2, ISRC3 IBIAS0, IBIAS1, IBIAS2, IBIAS3 64-pin ISRC0, ISRC1, ISRC2, ISRC3 IBIAS0, IBIAS1, IBIAS2, IBIAS3 80-pin ISRC0, ISRC1, ISRC2, ISRC3 IBIAS0, IBIAS1, IBIAS2, IBIAS3 The Current Bias Generator (CBG) consists of two classes of current sources: 10 μA and 50 μA sources. The major features of each current source are: • 10 μA Current Sources: - Current sourcing only - Up to four independent sources • 50 μA Current Sources: - Selectable current sourcing or sinking - Selectable current mirroring for sourcing and sinking A simplified block diagram of the CBG module is shown in Figure 20-1.  2017-2019 Microchip Technology Inc. DS70005319D-page 661 dsPIC33CH128MP508 FAMILY CONSTANT-CURRENT SOURCE MODULE BLOCK DIAGRAM(2) FIGURE 20-1: 10 µA Source 50 µA Source AVDD AVDD ON SRCENX I10ENX RESD(1) ADC RESD(1) IBIASx RESD(1) ISRCx SNKENX AVSS ADC Note 1: RESD is typically 300 Ohms; for more information, refer to the device data sheet. 2: In Figure 20-1 only, the ADC analog input is shown for clarity. Each analog peripheral connected to the pin has a separate Electrostatic Discharge (ESD) resistor. DS70005319D-page 662  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 20.1 Current Bias Generator Control Registers REGISTER 20-1: BIASCON: CURRENT BIAS GENERATOR CONTROL REGISTER R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 ON — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — — I10EN3 I10EN2 I10EN1 I10EN0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 ON: Current Bias Module Enable bit 1 = Module is enabled 0 = Module is disabled bit 14-4 Unimplemented: Read as ‘0’ bit 3 I10EN3: 10 μA Enable for Output 3 bit 1 = 10 μA output is enabled 0 = 10 μA output is disabled bit 2 I10EN2: 10 μA Enable for Output 2 bit 1 = 10 μA output is enabled 0 = 10 μA output is disabled bit 1 I10EN1: 10 μA Enable for Output 1 bit 1 = 10 μA output is enabled 0 = 10 μA output is disabled bit 0 I10EN0: 10 μA Enable for Output 0 bit 1 = 10 μA output is enabled 0 = 10 μA output is disabled  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 663 dsPIC33CH128MP508 FAMILY REGISTER 20-2: IBIASCONH: CURRENT BIAS GENERATOR 50 μA CURRENT SOURCE CONTROL HIGH REGISTER U-0 U-0 — — R/W-0 R/W-0 R/W-0 R/W-0 SHRSRCEN3 SHRSNKEN3 GENSRCEN3 GENSNKEN3 R/W-0 R/W-0 SRCEN3 SNKEN3 bit 15 bit 8 U-0 U-0 — — R/W-0 R/W-0 R/W-0 R/W-0 SHRSRCEN2 SHRSNKEN2 GENSRCEN2 GENSNKEN2 R/W-0 R/W-0 SRCEN2 SNKEN2 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 SHRSRCEN3: Share Source Enable for Output #3 bit 1 = Sourcing Current Mirror mode is enabled (uses reference from another source) 0 = Sourcing Current Mirror mode is disabled bit 12 SHRSNKEN3: Share Sink Enable for Output #3 bit 1 = Sinking Current Mirror mode is enabled (uses reference from another source) 0 = Sinking Current Mirror mode is disabled bit 11 GENSRCEN3: Generated Source Enable for Output #3 bit 1 = Source generates the current source mirror reference 0 = Source does not generate the current source mirror reference bit 10 GENSNKEN3: Generated Sink Enable for Output #3 bit 1 = Source generates the current source mirror reference 0 = Source does not generate the current source mirror reference bit 9 SRCEN3: Source Enable for Output #3 bit 1 = Current source is enabled 0 = Current source is disabled bit 8 SNKEN3: Sink Enable for Output #3 bit 1 = Current sink is enabled 0 = Current sink is disabled bit 7-6 Unimplemented: Read as ‘0’ bit 5 SHRSRCEN2: Share Source Enable for Output #2 bit 1 = Sourcing Current Mirror mode is enabled (uses reference from another source) 0 = Sourcing Current Mirror mode is disabled bit 4 SHRSNKEN2: Share Sink Enable for Output #2 bit 1 = Sinking Current Mirror mode is enabled (uses reference from another source) 0 = Sinking Current Mirror mode is disabled bit 3 GENSRCEN2: Generated Source Enable for Output #2 bit 1 = Source generates the current source mirror reference 0 = Source does not generate the current source mirror reference bit 2 GENSNKEN2: Generated Sink Enable for Output #2 bit 1 = Source generates the current source mirror reference 0 = Source does not generate the current source mirror reference bit 1 SRCEN2: Source Enable for Output #2 bit 1 = Current source is enabled 0 = Current source is disabled bit 0 SNKEN2: Sink Enable for Output #2 bit 1 = Current sink is enabled 0 = Current sink is disabled DS70005319D-page 664  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 20-3: IBIASCONL: CURRENT BIAS GENERATOR 50 μA CURRENT SOURCE CONTROL LOW REGISTER U-0 U-0 — — R/W-0 R/W-0 R/W-0 R/W-0 SHRSRCEN1 SHRSNKEN1 GENSRCEN1 GENSNKEN1 R/W-0 R/W-0 SRCEN1 SNKEN1 bit 15 bit 8 U-0 U-0 — — R/W-0 R/W-0 R/W-0 R/W-0 SHRSRCEN0 SHRSNKEN0 GENSRCEN0 GENSNKEN0 R/W-0 R/W-0 SRCEN0 SNKEN0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 SHRSRCEN1: Share Source Enable for Output #1 bit 1 = Sourcing Current Mirror mode is enabled (uses reference from another source) 0 = Sourcing Current Mirror mode is disabled bit 12 SHRSNKEN1: Share Sink Enable for Output #1 bit 1 = Sinking Current Mirror mode is enabled (uses reference from another source) 0 = Sinking Current Mirror mode is disabled bit 11 GENSRCEN1: Generated Source Enable for Output #1 bit 1 = Source generates the current source mirror reference 0 = Source does not generate the current source mirror reference bit 10 GENSNKEN1: Generated Sink Enable for Output #1 bit 1 = Source generates the current source mirror reference 0 = Source does not generate the current source mirror reference bit 9 SRCEN1: Source Enable for Output #1 bit 1 = Current source is enabled 0 = Current source is disabled bit 8 SNKEN1: Sink Enable for Output #1 bit 1 = Current sink is enabled 0 = Current sink is disabled bit 7-6 Unimplemented: Read as ‘0’ bit 5 SHRSRCEN0: Share Source Enable for Output #0 bit 1 = Sourcing Current Mirror mode is enabled (uses reference from another source) 0 = Sourcing Current Mirror mode is disabled bit 4 SHRSNKEN0: Share Sink Enable for Output #0 bit 1 = Sinking Current Mirror mode is enabled (uses reference from another source) 0 = Sinking Current Mirror mode is disabled bit 3 GENSRCEN0: Generated Source Enable for Output #0 bit 1 = Source generates the current source mirror reference 0 = Source does not generate the current source mirror reference bit 2 GENSNKEN0: Generated Sink Enable for Output #0 bit 1 = Source generates the current source mirror reference 0 = Source does not generate the current source mirror reference bit 1 SRCEN0: Source Enable for Output #0 bit 1 = Current source is enabled 0 = Current source is disabled bit 0 SNKEN0: Sink Enable for Output #0 bit 1 = Current sink is enabled 0 = Current sink is disabled  2017-2019 Microchip Technology Inc. DS70005319D-page 665 dsPIC33CH128MP508 FAMILY NOTES: DS70005319D-page 666  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 21.0 Note: SPECIAL FEATURES This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to the related section of the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). The dsPIC33CH128MP508 family devices include several features intended to maximize application flexibility and reliability, and minimize cost through elimination of external components. These are: • • • • • • • Flexible Configuration Watchdog Timer (WDT) Code Protection and CodeGuard™ Security JTAG Boundary Scan Interface In-Circuit Serial Programming™ (ICSP™) In-Circuit Emulation Brown-out Reset (BOR) 21.1 Configuration Bits In dsPIC33CH128MP508 family devices, the Configuration Words are implemented as volatile memory. This means that configuration data will get loaded to volatile memory (from the Flash Configuration Words) each time the device is powered up. Configuration data are stored at the end of the on-chip program memory space, known as the Flash Configuration Words. Their specific locations are shown in Table 21-1. The configuration data are automatically loaded from the Flash Configuration Words to the proper Configuration Shadow registers during device Resets. Note: Configuration data are reloaded on all types of device Master Resets. Slave Resets do not load the Configuration registers. It is recommended not to change the Slave Configuration register without resetting the Slave along with the Master (S1MSRE = 1). When creating applications for these devices, users should always specifically allocate the location of the Flash Configuration Words for configuration data in their code for the compiler. This is to make certain that program code is not stored in this address when the code is compiled. Program code executing out of configuration space will cause a device Reset. The Master code, as well as the Slave code, are located in Flash memory. Table 21-1 shows the Master and the Slave Configuration registers and their address locations in Flash memory.  2017-2019 Microchip Technology Inc. Slave Configuration bits are located in the Master Flash and loaded during a Master Reset. Note: Performing a page erase operation on the last page of program memory clears the Flash Configuration Words. TABLE 21-1: Register CONFIGURATION WORD ADDRESSES 64k Address 128k Address Master/General Configuration Registers FSEC 00AF00 015F00 FBSLIM 00AF10 015F10 FSIGN 00AF14 015F14 FOSCSEL 00AF18 015F18 FOSC 00AF1C 015F1C FWDT 00AF20 015F20 FPOR 00AF24 015F24 FICD 00AF28 015F28 FDMTIVTL 00AF2C 015F2C FDMTIVTH 00AF30 015F30 FDMTCNTL 00AF34 015F34 FDMTCNTH 00AF38 015F38 FDMT 00AF3C 015F3C FDEVOPT 00AF40 015F40 FALTREG 00AF44 015F44 FMBXM 00AF48 015F48 FMBXHS1 00AFC4 015F4C FMBXHS2 00AF50 015F50 FMBXHSEN 00AF54 015F54 FCFGPRA0 00AF58 015F58 FCFGPRB0 00AF60 015F60 FCFGPRC0 00AF68 015F68 FCFGPRD0 00AF70 015F70 FCFGPRE0 00AF78 015F7C Slave Configuration Registers FS1OSCSEL 00AF80 015F80 FS1OSC 00AF84 015F84 FS1WDT 00AF88 015F88 FS1POR 00AF8C 015F8C FS1ICD 00AF90 015F90 FS1DEVOPT 00AF94 015F94 FS1ALTREG 00AF98 015F98 DS70005319D-page 667 Register Name MASTER CONFIGURATION REGISTERS MAP Bits 23-16 Bit 15 Bit 14 Bit 13 Bit 12 FSEC — AIVTDIS — — — FBSLIM — — — — FSIGN — r(2) — — — — — — — — FOSCSEL — — — — — — — — — IESO FOSC — — — — XTBST — r(1) FWDT — FWDTEN FPOR — — FICD — — Bit 11 Bit 10 CSS[2:0] — Bit 8 Bit 7 CWRP Bit 6 Bit 5 Bit 4 Bit 3 GWRP — BSEN — — — — — — — — — — — GSS[1:0] Bit 2 Bit 1 XTCFG[1:0] — — — — WDTWIN[1:0] — — — — — — FCKSM[1:0] WINDIS RCLKSEL[1:0] BSS[1:0] BWRP r(1) r(1) — — — — JTAGEN — — — — — DMTIVT[15:0] DMTIVT[31:16] FDMTCNTL — DMTCNT[15:0] FDMTCNTH — DMTCNT[31:16] FDMT — — — — — — — — — — — — FDEVOPT — — — SPI2PIN — — SMBEN r(1) r(1) r(1) — — FALTREG — — — OSCIOFNC — — CTXT3[2:0] — CTXT2[2:0] POSCMD[1:0] ALTI2C[2:1] — — — DMTDIS r(1) — — — CTXT1[2:0] FMBXM — — MBXHSD[3:0] MBXHSC[3:0] MBXHSB[3:0] MBXHSA[3:0] FMBXHS2 — MBXHSH[3:0] MBXHSG[3:0] MBXHSF[3:0] MBXHSE[3:0] FMBXHSEN — — — — — — — — — FCFGPRA0 — — — — — — — — — FCFGPRB0 — CPRB[15:0] FCFGPRC0 — CPRC[15:0] FCFGPRD0 — CPRD[15:0] FCFGPRE0 — CPRE[15:0] MBXM[15:0]  2017-2019 Microchip Technology Inc. — = unimplemented bit, read as ‘1’; r = reserved bit. Bit is reserved, maintain as ‘1’. Bit is reserved, maintain as ‘0’. HS[H:A]EN — — — ICS[1:0] FMBXHS1 — — RWDTPS[4:0] r(1) — — FNOSC[2:0] — FDMTIVTL CTXT4[2:0] — — FDMTIVTH Legend: Note 1: 2: Bit 0 BSLIM[12:0] SWDTPS[4:0] — Bit 9 CPRA[4:0] dsPIC33CH128MP508 FAMILY DS70005319D-page 668 TABLE 21-2:  2017-2019 Microchip Technology Inc. TABLE 21-3: Register Name SLAVE CONFIGURATION REGISTERS MAP Bits 23-16 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 FS1OSCSEL — — — — — — — FS1OSC — — — — — — — FS1WDT — S1FWDTEN S1SWDTPS[4:0] Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 — — S1IESO — — — — — r(1) S1FCKSM[1:0] — — — S1WDTWIN[1:0] S1WINDIS S1RCLKSEL[1:0] Bit 2 Bit 1 Bit 0 S1FNOSC[2:0] S1OSCIOFNC — — — S1RWDTPS[4:0] FS1POR — — — — — — — — — — — — — — — — FS1ICD — S1NOBTSWP — S1ISOLAT — — — — — r(1) — — — — — S1ICS[1:0](2) FS1DEVOPT — S1MSRE S1SSRE S1SPI1PIN — — — — — — — — — S1ALTI2C1 — FS1ALTREG — — Legend: Note 1: 2: S1CTXT4[2:0] — S1CTXT3[2:0] — S1CTXT2[2:0] — — — S1CTXT1[2:0] — = unimplemented bit, read as ‘1’; r = reserved bit. Bit is reserved, maintain as ‘1’. Only valid in Dual Debug mode. dsPIC33CH128MP508 FAMILY DS70005319D-page 669 dsPIC33CH128MP508 FAMILY REGISTER 21-1: FSEC CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 R/PO-1 U-1 U-1 U-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 AIVTDIS — — — CSS2 CSS1 CSS0 CWRP bit 15 bit 8 R/PO-1 R/PO-1 R/PO-1 U-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 GSS1 GSS0 GWRP — BSEN BSS1 BSS0 BWRP bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 23-16 Unimplemented: Read as ‘1’ bit 15 AIVTDIS: Alternate Interrupt Vector Table Disable bit 1 = Disables AIVT 0 = Enables AIVT bit 14-12 Unimplemented: Read as ‘1’ bit 11-9 CSS[2:0]: Configuration Segment Code Flash Protection Level bits 111 = No protection (other than CWRP write protection) 110 = Standard security 10x = Enhanced security 0xx = High security bit 8 CWRP: Configuration Segment Write-Protect bit 1 = Configuration Segment is not write-protected 0 = Configuration Segment is write-protected bit 7-6 GSS[1:0]: General Segment Code Flash Protection Level bits 11 = No protection (other than GWRP write protection) 10 = Standard security 0x = High security bit 5 GWRP: General Segment Write-Protect bit 1 = User program memory is not write-protected 0 = User program memory is write-protected bit 4 Unimplemented: Read as ‘1’ bit 3 BSEN: Boot Segment Control bit 1 = No Boot Segment 0 = Boot Segment size is determined by BSLIM[12:0] bit 2-1 BSS[1:0]: Boot Segment Code Flash Protection Level bits 11 = No protection (other than BWRP write protection) 10 = Standard security 0x = High security bit 0 BWRP: Boot Segment Write-Protect bit 1 = User program memory is not write-protected 0 = User program memory is write-protected DS70005319D-page 670  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 21-2: FBSLIM CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 U-1 U-1 U-1 — — — R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 BSLIM[12:8] bit 15 bit 8 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 BSLIM[7:0] bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 23-13 Unimplemented: Read as ‘1’ bit 12-0 BSLIM[12:0]: Boot Segment Code Flash Page Address Limit bits Contains the page address of the first active General Segment page. The value to be programmed is the inverted page address, such that programming additional ‘0’s can only increase the Boot Segment size. REGISTER 21-3: FSIGN CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 r-0 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 15 bit 8 U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 7 bit 0 Legend: r = Reserved bit PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 23-16 Unimplemented: Read as ‘1’ bit 15 Reserved: Maintain as ‘0’ bit 14-0 Unimplemented: Read as ‘1’  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 671 dsPIC33CH128MP508 FAMILY REGISTER 21-4: FOSCSEL CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 15 bit 8 R/PO-1 U-1 U-1 U-1 U-1 IESO — — — — R/PO-1 R/PO-1 R/PO-1 FNOSC[2:0] bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 23-8 Unimplemented: Read as ‘1’ bit 7 IESO: Internal External Switchover bit 1 = Internal External Switchover mode is enabled (Two-Speed Start-up is enabled) 0 = Internal External Switchover mode is disabled (Two-Speed Start-up is disabled) bit 6-3 Unimplemented: Read as ‘1’ bit 2-0 FNOSC[2:0]: Initial Oscillator Source Selection bits 111 = Internal Fast RC (FRC) Oscillator with Postscaler 110 = Backup Fast RC (BFRC) 101 = LPRC Oscillator 100 = Reserved 011 = Primary Oscillator with PLL (XTPLL, HSPLL, ECPLL) 010 = Primary (XT, HS, EC) Oscillator 001 = Internal Fast RC Oscillator with PLL (FRCPLL) 000 = Fast RC (FRC) Oscillator DS70005319D-page 672  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 21-5: FOSC CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 U-1 U-1 U-1 — — — R/PO-1 XTBST R/PO-1 XTCFG1 R/PO-1 U-1 r-1 XTCFG0 — — bit 15 bit 8 R/PO-1 R/PO-1 FCKSM1 FCKSM0 U-1 — U-1 U-1 — — R/PO-1 (1) OSCIOFNC R/PO-1 R/PO-1 POSCMD1 POSCMD0 bit 7 bit 0 Legend: PO = Program Once bit r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 23-13 Unimplemented: Read as ‘1’ bit 12 XTBST: Oscillator Kick-Start Programmability bit 1 = Boosts the kick-start 0 = Default kick-start bit 11-10 XTCFG[1:0]: Crystal Oscillator Drive Select bits Current gain programmability for oscillator (output drive). 11 = Gain3 (use for 24-32 MHz crystals) 10 = Gain2 (use for 16-24 MHz crystals) 01 = Gain1 (use for 8-16 MHz crystals) 00 = Gain0 (use for 4-8 MHz crystals) bit 9 Unimplemented: Read as ‘1’ bit 8 Reserved: Maintain as ‘1’ bit 7-6 FCKSM[1:0]: Clock Switching Mode bits 1x = Clock switching is disabled, Fail-Safe Clock Monitor is disabled 01 = Clock switching is enabled, Fail-Safe Clock Monitor is disabled 00 = Clock switching is enabled, Fail-Safe Clock Monitor is enabled bit 5-3 Unimplemented: Read as ‘1’ bit 2 OSCIOFNC: OSCO Pin Function bit (except in XT and HS modes)(1) 1 = OSCO is the clock output 0 = OSCO is the general purpose digital I/O pin bit 1-0 POSCMD[1:0]: Primary Oscillator Mode Select bits 11 = Primary Oscillator is disabled 10 = HS Crystal Oscillator mode (10 MHz-32 MHz) 01 = XT Crystal Oscillator mode (3.5 MHz-10 MHz) 00 = EC (External Clock) mode Note 1: x = Bit is unknown The OSCO pin function is determined by the S1OSCIOFNC Configuration bit. If both the Master core OSCIOFNC and Slave core S1OSCIOFNC bits are set, the Master core OSCIOFNC bit has priority.  2017-2019 Microchip Technology Inc. DS70005319D-page 673 dsPIC33CH128MP508 FAMILY REGISTER 21-6: FWDT CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 FWDTEN SWDTPS4 SWDTPS3 SWDTPS2 SWDTPS1 SWDTPS0 WDTWIN1 WDTWIN0 bit 15 bit 8 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 WINDIS RCLKSEL1 RCLKSEL0 RWDTPS4 RWDTPS3 RWDTPS2 RWDTPS1 RWDTPS0 bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 23-16 Unimplemented: Read as ‘1’ bit 15 FWDTEN: Watchdog Timer Enable bit 1 = WDT is enabled in hardware 0 = WDT controller via the ON bit (WDTCONL[15]) bit 14-10 SWDTPS[4:0]: Sleep Mode Watchdog Timer Period Select bits 11111 = Divide by 231 = 2,147,483,648 x = Bit is unknown 11110 = Divide by 230 = 1,073,741,824 ... 00001 = Divide by 21 = 2 00000 = Divide by 20 = 1 bit 9-8 WDTWIN[1:0]: Watchdog Timer Window Select bits 11 = WDT window is 25% of the WDT period 10 = WDT window is 37.5% of the WDT period 01 = WDT window is 50% of the WDT period 00 = WDT Window is 75% of the WDT period bit 7 WINDIS: Watchdog Timer Window Enable bit 1 = Watchdog Timer is in Non-Window mode 0 = Watchdog Timer is in Window mode bit 6-5 RCLKSEL[1:0]: Watchdog Timer Clock Select bits 11 = LPRC clock 10 = Uses FRC when WINDIS = 0, system clock is not INTOSC/LPRC and device is not in Sleep; otherwise, uses INTOSC/LPRC 01 = Uses peripheral clock when system clock is not INTOSC/LPRC and device is not in Sleep; otherwise, uses INTOSC/LPRC 00 = Reserved bit 4-0 RWDTPS[4:0]: Run Mode Watchdog Timer Period Select bits 11111 = Divide by 231 = 2,147,483,648 11110 = Divide by 230 = 1,073,741,824 ... 00001 = Divide by 21 = 2 00000 = Divide by 20 = 1 DS70005319D-page 674  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 21-7: FPOR CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 15 bit 8 U-1 U-1 r-1 r-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 7 bit 0 Legend: PO = Program Once bit r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 23-6 Unimplemented: Read as ‘1’ bit 5-4 Reserved: Maintain as ‘1’ bit 3-0 Unimplemented: Read as ‘1’  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 675 dsPIC33CH128MP508 FAMILY REGISTER 21-8: FICD CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 15 bit 8 r-1 U-1 R/PO-1 U-1 U-1 U-1 R/PO-1 R/PO-1 — — JTAGEN — — — ICS1 ICS0 bit 7 bit 0 Legend: PO = Program Once bit r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 23-8 Unimplemented: Read as ‘1’ bit 7 Reserved: Maintain as ‘1’ bit 6 Unimplemented: Read as ‘1’ bit 5 JTAGEN: JTAG Enable bit 1 = JTAG port is enabled 0 = JTAG port is disabled bit 4-2 Unimplemented: Read as ‘1’ bit 1-0 ICS[1:0]: ICD Communication Channel Select bits 11 = Master communicates on PGC1 and PGD1 10 = Master communicates on PGC2 and PGD2 01 = Master communicates on PGC3 and PGD3 00 = Reserved, do not use DS70005319D-page 676 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 21-9: FDMTIVTL CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 DMTIVT[15:8] bit 15 bit 8 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 DMTIVT[7:0] bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 23-16 Unimplemented: Read as ‘1’ bit 15-0 DMTIVT[15:0]: DMT Window Interval Lower 16 bits x = Bit is unknown REGISTER 21-10: FDMTIVTH CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 DMTIVT[31:24] bit 15 bit 8 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 DMTIVT[23:16] bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 23-16 Unimplemented: Read as ‘1’ bit 15-0 DMTIVT[31:16]: DMT Window Interval Higher 16 bits  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 677 dsPIC33CH128MP508 FAMILY REGISTER 21-11: FDMTCNTL CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 DMTCNT[15:8] bit 15 bit 8 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 DMTCNT[7:0] bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 23-16 Unimplemented: Read as ‘1’ bit 15-0 DMTCNT[15:0]: DMT Instruction Count Time-out Value Lower 16 bits REGISTER 21-12: FDMTCNTH CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 DMTCNT[31:24] bit 15 bit 8 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 DMTCNT[23:16] bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 23-16 Unimplemented: Read as ‘1’ bit 15-0 DMTCNT[31:16]: DMT Instruction Count Time-out Value Upper 16 bits DS70005319D-page 678  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 21-13: FDMT CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 15 bit 8 U-1 U-1 U-1 U-1 U-1 U-1 U-1 R/PO-1 — — — — — — — DMTDIS bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 23-1 Unimplemented: Read as ‘1’ bit 0 DMTDIS: DMT Disable bit 1 = DMT is disabled 0 = DMT is enabled  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 679 dsPIC33CH128MP508 FAMILY REGISTER 21-14: FDEVOPT CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 U-1 U-1 R/PO-1 U-1 U-1 R/PO-1 r-1 r-1 — — SPI2PIN(1) — — SMBEN — — bit 15 bit 8 r-1 U-1 U-1 R/PO-1 R/PO-1 r-1 U-1 U-1 — — — ALTI2C2 ALTI2C1 — — — bit 7 bit 0 Legend: PO = Program Once bit r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 23-14 Unimplemented: Read as ‘1’ bit 13 SPI2PIN: Master SPI #2 Fast I/O Pad Disable bit(1) 1 = Master SPI2 uses PPS (I/O remap) to make connections with device pins 0 = Master SPI2 uses direct connections with specified device pins bit 12-11 Unimplemented: Read as ‘1’ bit 10 SMBEN: Select Input Voltage Threshold for I2C Pads to be SMBus 3.0 Compliant bit 1 = Enables SMBus 3.0 input threshold voltage 0 = I2C pad input buffer operation bit 9-7 Reserved: Maintain as ‘1’ bit 6-5 Unimplemented: Read as ‘1’ bit 4 ALTI2C2: Alternate I2C2 Pin Mapping bit 1 = Default location for SCL2/SDA2 pins 0 = Alternate location for SCL2/SDA2 pins (ASCL2/ASDA2) bit 3 ALTI2C1: Alternate I2C1 Pin Mapping bit 1 = Default location for SCL1/SDA1 pins 0 = Alternate location for SCL1/SDA1 pins (ASCL1/ASDA1) bit 2 Reserved: Maintain as ‘1’ bit 1-0 Unimplemented: Read as ‘1’ Note 1: Fixed pin option is only available for higher pin packages (48-pin, 64-pin and 80-pin). DS70005319D-page 680  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 21-15: FALTREG CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 U-1 R/PO-1 — R/PO-1 R/PO-1 CTXT4[2:0] U-1 R/PO-1 — R/PO-1 R/PO-1 CTXT3[2:0] bit 15 bit 8 U-1 R/PO-1 — R/PO-1 R/PO-1 CTXT2[2:0] U-1 R/PO-1 — R/PO-1 R/PO-1 CTXT1[2:0] bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 23-15 Unimplemented: Read as ‘1’ bit 14-12 CTXT4[2:0]: Specifies the Alternate Working Register Set #4 with Interrupt Priority Levels (IPL) bits 111 = Not assigned 110 = Alternate Register Set #4 is assigned to IPL Level 7 101 = Alternate Register Set #4 is assigned to IPL Level 6 100 = Alternate Register Set #4 is assigned to IPL Level 5 011 = Alternate Register Set #4 is assigned to IPL Level 4 010 = Alternate Register Set #4 is assigned to IPL Level 3 001 = Alternate Register Set #4 is assigned to IPL Level 2 000 = Alternate Register Set #4 is assigned to IPL Level 1 bit 11 Unimplemented: Read as ‘1’ bit 10-8 CTXT3[2:0]: Specifies the Alternate Working Register Set #3 with Interrupt Priority Levels (IPL) bits 111 = Not assigned 110 = Alternate Register Set #3 is assigned to IPL Level 7 101 = Alternate Register Set #3 is assigned to IPL Level 6 100 = Alternate Register Set #3 is assigned to IPL Level 5 011 = Alternate Register Set #3 is assigned to IPL Level 4 010 = Alternate Register Set #3 is assigned to IPL Level 3 001 = Alternate Register Set #3 is assigned to IPL Level 2 000 = Alternate Register Set #3 is assigned to IPL Level 1 bit 7 Unimplemented: Read as ‘1’ bit 6-4 CTXT2[2:0]: Specifies the Alternate Working Register Set #2 with Interrupt Priority Levels (IPL) bits 111 = Not assigned 110 = Alternate Register Set #2 is assigned to IPL Level 7 101 = Alternate Register Set #2 is assigned to IPL Level 6 100 = Alternate Register Set #2 is assigned to IPL Level 5 011 = Alternate Register Set #2 is assigned to IPL Level 4 010 = Alternate Register Set #2 is assigned to IPL Level 3 001 = Alternate Register Set #2 is assigned to IPL Level 2 000 = Alternate Register Set #2 is assigned to IPL Level 1 bit 3 Unimplemented: Read as ‘1’  2017-2019 Microchip Technology Inc. DS70005319D-page 681 dsPIC33CH128MP508 FAMILY REGISTER 21-15: FALTREG CONFIGURATION REGISTER (CONTINUED) bit 2-0 CTXT1[2:0]: Specifies the Alternate Working Register Set #1 with Interrupt Priority Levels (IPL) bits 111 = Not assigned 110 = Alternate Register Set #1 is assigned to IPL Level 7 101 = Alternate Register Set #1 is assigned to IPL Level 6 100 = Alternate Register Set #1 is assigned to IPL Level 5 011 = Alternate Register Set #1 is assigned to IPL Level 4 010 = Alternate Register Set #1 is assigned to IPL Level 3 001 = Alternate Register Set #1 is assigned to IPL Level 2 000 = Alternate Register Set #1 is assigned to IPL Level 1 REGISTER 21-16: FMBXM CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 MBXM15 MBXM14 MBXM13 MBXM12 MBXM11 MBXM10 MBXM9 MBXM8 bit 15 bit 8 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 MBXM7 MBXM6 MBXM5 MBXM4 MBXM3 MBXM2 MBXM1 MBXM0 bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 23-16 Unimplemented: Read as ‘1’ bit 15 MBXM15: Mailbox Data Register Channel Direction Fuses bits 1 = Mailbox Register #15 is configured for Master data read (Slave to Master data transfer) 0 = Mailbox Register #15 is configured for Master data write (Master to Slave data transfer) bit 14 MBXM14: Mailbox Data Register Channel Direction Fuses bits 1 = Mailbox Register #14 is configured for Master data read (Slave to Master data transfer) 0 = Mailbox Register #14 is configured for Master data write (Master to Slave data transfer) bit 13 MBXM13: Mailbox Data Register Channel Direction Fuses bits 1 = Mailbox Register #13 is configured for Master data read (Slave to Master data transfer) 0 = Mailbox Register #13 is configured for Master data write (Master to Slave data transfer) bit 12 MBXM12: Mailbox Data Register Channel Direction Fuses bits 1 = Mailbox Register #12 is configured for Master data read (Slave to Master data transfer) 0 = Mailbox Register #12 is configured for Master data write (Master to Slave data transfer) bit 11 MBXM11: Mailbox Data Register Channel Direction Fuses bits 1 = Mailbox Register #11 is configured for Master data read (Slave to Master data transfer) 0 = Mailbox Register #11 is configured for Master data write (Master to Slave data transfer) bit 10 MBXM10: Mailbox Data Register Channel Direction Fuses bits 1 = Mailbox Register #10 is configured for Master data read (Slave to Master data transfer) 0 = Mailbox Register #10 is configured for Master data write (Master to Slave data transfer) DS70005319D-page 682  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 21-16: FMBXM CONFIGURATION REGISTER (CONTINUED) bit 9 MBXM9: Mailbox Data Register Channel Direction Fuses bits 1 = Mailbox Register #9 is configured for Master data read (Slave to Master data transfer) 0 = Mailbox Register #9 is configured for Master data write (Master to Slave data transfer) bit 8 MBXM8: Mailbox Data Register Channel Direction Fuses bits 1 = Mailbox Register #8 is configured for Master data read (Slave to Master data transfer) 0 = Mailbox Register #8 is configured for Master data write (Master to Slave data transfer) bit 7 MBXM7: Mailbox Data Register Channel Direction Fuses bits 1 = Mailbox Register #7 is configured for Master data read (Slave to Master data transfer) 0 = Mailbox Register #7 is configured for Master data write (Master to Slave data transfer) bit 6 MBXM6: Mailbox Data Register Channel Direction Fuses bits 1 = Mailbox Register #6 is configured for Master data read (Slave to Master data transfer) 0 = Mailbox Register #6 is configured for Master data write (Master to Slave data transfer) bit 5 MBXM5: Mailbox Data Register Channel Direction Fuses bits 1 = Mailbox Register #5 is configured for Master data read (Slave to Master data transfer) 0 = Mailbox Register #5 is configured for Master data write (Master to Slave data transfer) bit 4 MBXM4: Mailbox Data Register Channel Direction Fuses bits 1 = Mailbox Register #4 is configured for Master data read (Slave to Master data transfer) 0 = Mailbox Register #4 is configured for Master data write (Master to Slave data transfer) bit 3 MBXM3: Mailbox Data Register Channel Direction Fuses bits 1 = Mailbox Register #3 is configured for Master data read (Slave to Master data transfer) 0 = Mailbox Register #3 is configured for Master data write (Master to Slave data transfer) bit 2 MBXM2: Mailbox Data Register Channel Direction Fuses bits 1 = Mailbox Register #2 is configured for Master data read (Slave to Master data transfer) 0 = Mailbox Register #2 is configured for Master data write (Master to Slave data transfer) bit 1 MBXM1: Mailbox Data Register Channel Direction Fuses bits 1 = Mailbox Register #1 is configured for Master data read (Slave to Master data transfer) 0 = Mailbox Register #1 is configured for Master data write (Master to Slave data transfer) bit 0 MBXM0: Mailbox Data Register Channel Direction Fuses bits 1 = Mailbox Register #0 is configured for Master data read (Slave to Master data transfer) 0 = Mailbox Register #0 is configured for Master data write (Master to Slave data transfer)  2017-2019 Microchip Technology Inc. DS70005319D-page 683 dsPIC33CH128MP508 FAMILY REGISTER 21-17: FMBXHS1 CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 MBXHSD3 MBXHSD2 MBXHSD1 MBXHSD0 MBXHSC3 MBXHSC2 MBXHSC1 MBXHSC0 bit 15 bit 8 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 MBXHSB3 MBXHSB2 MBXHSB1 MBXHSB0 MBXHSA3 MBXHSA2 MBXHSA1 MBXHSA0 bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 23-16 Unimplemented: Read as ‘1’ bit 15-12 MBXHSD[3:0]: Mailbox Handshake Protocol Block D Register Assignment bits 1111 = MSIxMBXD15 is assigned to Mailbox Handshake Protocol Block D ... 0001 = MSIxMBXD1 is assigned to Mailbox Handshake Protocol Block D 0000 = MSIxMBXD0 is assigned to Mailbox Handshake Protocol Block D bit 11-8 MBXHSC[3:0]: Mailbox Handshake Protocol Block C Register Assignment bits 1111 = MSIxMBXD15 is assigned to Mailbox Handshake Protocol Block C ... 0001 = MSIxMBXD1 is assigned to Mailbox Handshake Protocol Block C 0000 = MSIxMBXD0 is assigned to Mailbox Handshake Protocol Block C bit 7-4 MBXHSB[3:0]: Mailbox Handshake Protocol Block B Register Assignment bits 1111 = MSIxMBXD15 is assigned to Mailbox Handshake Protocol Block B ... 0001 = MSIxMBXD1 is assigned to Mailbox Handshake Protocol Block B 0000 = MSIxMBXD0 is assigned to Mailbox Handshake Protocol Block B bit 3-0 MBXHSA[3:0]: Mailbox Handshake Protocol Block A Register Assignment bits 1111 = MSIxMBXD15 is assigned to Mailbox Handshake Protocol Block A ... 0001 = MSIxMBXD1 is assigned to Mailbox Handshake Protocol Block A 0000 = MSIxMBXD0 is assigned to Mailbox Handshake Protocol Block A DS70005319D-page 684  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 21-18: FMBXHS2 CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 MBXHSH3 MBXHSH2 MBXHSH1 MBXHSH0 MBXHSG3 MBXHSG2 MBXHSG1 MBXHSG0 bit 15 bit 8 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 MBXHSF3 MBXHSF2 MBXHSF1 MBXHSF0 MBXHSE3 MBXHSE2 MBXHSE1 MBXHSE0 bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 23-16 Unimplemented: Read as ‘1’ bit 15-12 MBXHSH[3:0]: Mailbox Handshake Protocol Block H Register Assignment bits 1111 = MSIxMBXD15 is assigned to Mailbox Handshake Protocol Block H ... 0001 = MSIxMBXD1 is assigned to Mailbox Handshake Protocol Block H 0000 = MSIxMBXD0 is assigned to Mailbox Handshake Protocol Block H bit 11-8 MBXHSG[3:0]: Mailbox Handshake Protocol Block G Register Assignment bits 1111 = MSIxMBXD15 is assigned to Mailbox Handshake Protocol Block G ... 0001 = MSIxMBXD1 is assigned to Mailbox Handshake Protocol Block G 0000 = MSIxMBXD0 is assigned to Mailbox Handshake Protocol Block G bit 7-4 MBXHSF[3:0]: Mailbox Handshake Protocol Block F Register Assignment bits 1111 = MSIxMBXD15 is assigned to Mailbox Handshake Protocol Block F ... 0001 = MSIxMBXD1 is assigned to Mailbox Handshake Protocol Block F 0000 = MSIxMBXD0 is assigned to Mailbox Handshake Protocol Block F bit 3-0 MBXHSE[3:0]: Mailbox Handshake Protocol Block E Register Assignment bits 1111 = MSIxMBXD15 is assigned to Mailbox Handshake Protocol Block E ... 0001 = MSIxMBXD1 is assigned to Mailbox Handshake Protocol Block E 0000 = MSIxMBXD0 is assigned to Mailbox Handshake Protocol Block E  2017-2019 Microchip Technology Inc. DS70005319D-page 685 dsPIC33CH128MP508 FAMILY REGISTER 21-19: FMBXHSEN CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 15 bit 8 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 HS[H:A]EN bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 23-8 Unimplemented: Read as ‘1’ bit 7-0 HS[H:A]EN: Mailbox Data Flow Control Protocol Block x Enable Fuses bits (x = A, B, C, D, E, F, G, H) 1 = Mailbox data flow control handshake protocol block is disabled 0 = Mailbox data flow control handshake protocol block is enabled REGISTER 21-20: FCFGPRA0: PORTA CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 15 bit 8 U-1 U-1 U-1 — — — R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 CPRA[4:0] bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 23-5 Unimplemented: Read as ‘1’ bit 4-0 CPRA[4:0]: Configure PORTA Ownership bits 1 = Master core owns pin 0 = Slave core owns pin DS70005319D-page 686 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 21-21: FCFGPRB0: PORTB CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 CPRB[15:8] bit 15 bit 8 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 CPRB[7:0] bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 23-16 Unimplemented: Read as ‘1’ bit 15-0 CPRB[15:0]: Configure PORTB Ownership bits 1 = Master core owns pin 0 = Slave core owns pin x = Bit is unknown REGISTER 21-22: FCFGPRC0: PORTC CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 CPRC[15:8] bit 15 bit 8 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 CPRC[7:0] bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 23-16 Unimplemented: Read as ‘1’ bit 15-0 CPRC[15:0]: Configure PORTC Ownership bits 1 = Master core owns pin 0 = Slave core owns pin  2017-2019 Microchip Technology Inc. x = Bit is unknown DS70005319D-page 687 dsPIC33CH128MP508 FAMILY REGISTER 21-23: FCFGPRD0: PORTD CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 CPRD[15:8] bit 15 bit 8 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 CPRD[7:0] bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 23-16 Unimplemented: Read as ‘1’ bit 15-0 CPRD[15:0]: Configure PORTD Ownership bits 1 = Master core owns pin 0 = Slave core owns pin x = Bit is unknown REGISTER 21-24: FCFGPRE0: PORTE CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 CPRE[15:8] bit 15 bit 8 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 CPRE[7:0] bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 23-16 Unimplemented: Read as ‘1’ bit 15-0 CPRE[15:0]: Configure PORTE Ownership bits 1 = Master core owns pin 0 = Slave core owns pin DS70005319D-page 688 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 21-25: FS1OSCSEL CONFIGURATION REGISTER (SLAVE) U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 15 bit 8 R/PO-1 U-1 U-1 U-1 U-1 S1IESO — — — — R/PO-1 R/PO-1 R/PO-1 S1FNOSC[2:0] bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 23-8 Unimplemented: Read as ‘1’ bit 7 S1IESO: Internal External Switchover bit 1 = Internal External Switchover mode is enabled (Two-Speed Start-up is enabled) 0 = Internal External Switchover mode is disabled (Two-Speed Start-up is disabled) bit 6-3 Unimplemented: Read as ‘1’ bit 2-0 S1FNOSC[2:0]: Oscillator Selection bits 111 = Fast RC Oscillator (FRC) divided by N 110 = Backup FRC (BFRC) 101 = Low-Power RC Oscillator (LPRC) 100 = Reserved 011 = Primary Oscillator with PLL Module (MSPLL, HSPLL, ECPLL) 010 = Primary Oscillator (MS, HS, EC) 001 = Fast RC Oscillator (FRC) with PLL Module (FRCPLL) 000 = Fast RC Oscillator (FRC)  2017-2019 Microchip Technology Inc. DS70005319D-page 689 dsPIC33CH128MP508 FAMILY REGISTER 21-26: FS1OSC CONFIGURATION REGISTER (SLAVE) U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 U-1 U-1 U-1 U-1 U-1 U-1 U-1 r-1 — — — — — — — — bit 15 bit 8 R/PO-1 R/PO-1 S1FCKSM[1:0] U-1 U-1 U-1 R/PO-1 U-1 U-1 — — — S1OSCIOFNC(1) — — bit 7 bit 0 Legend: PO = Program Once bit r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 23-9 Unimplemented: Read as ‘1’ bit 8 Reserved: Maintain as ‘1’ bit 7-6 S1FCKSM[1:0]: Clock Switching and Monitor Selection Configuration bits 1x = Clock switching is disabled, Fail-Safe Clock Monitor is disabled 01 = Clock switching is enabled, Fail-Safe Clock Monitor is disabled 00 = Clock switching is enabled, Fail-Safe Clock Monitor is enabled bit 5-3 Unimplemented: Read as ‘1’ bit 2 S1OSCIOFNC: OSCO Pin Function bit (except in XT and HS modes)(1) 1 = OSCO is the clock output 0 = OSCO is the general purpose digital I/O pin bit 1-0 Unimplemented: Read as ‘1’ Note 1: The OSCO pin function is determined by the S1OSCIOFNC Configuration bit. If both the Master core OSCIOFNC and Slave core S1OSCIOFNC bits are set, the Master core OSCIOFNC bit has priority. DS70005319D-page 690  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 21-27: FS1WDT CONFIGURATION REGISTER (SLAVE) U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 S1FWDTEN S1SWDTPS4 S1SWDTPS3 S1SWDTPS2 S1SWDTPS1 S1SWDTPS0 S1WDTWIN1 S1WDTWIN0 bit 15 bit 8 R/PO-1 S1WINDIS R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 S1RCLKSEL1 S1RCLKSEL0 S1RWDTPS4 S1RWDTPS3 S1RWDTPS2 S1RWDTPS1 S1RWDTPS0 bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 23-16 Unimplemented: Read as ‘1’ bit 15 S1FWDTEN: Watchdog Timer Enable bit 1 = WDT is enabled in hardware 0 = WDT is controlled via the ON (WDTCONL[15]) bit bit 14-10 S1SWDTPS[4:0]: Sleep Mode Watchdog Timer Period Select bits 11111 = Divide by 231 = 2,147,483,648 11110 = Divide by 230 = 1,073,741,824 ... 00001 = Divide by 21 = 2 00000 = Divide by 20 = 1 bit 9-8 S1WDTWIN[1:0]: Watchdog Window Select bits 11 = WDT window is 25% of WDT period 10 = WDT window is 37.5% of WDT period 01 = WDT window is 50% of WDT period 00 = WDT window is 75% of WDT period bit 7 S1WINDIS: Windowed Watchdog Timer Disable bit 1 = Standard WDT is selected; windowed WDT is disabled 0 = Windowed WDT is enabled bit 6-5 S1RCLKSEL[1:0]: Watchdog Timer Clock Select bits 11 = LPRC 10 = Uses FRC when S1WINDIS = 0, system clock is not INTOSC/LPRC and the device is not in Sleep; otherwise, uses INTOSC/LPRC 01 = Uses the peripheral clock when the system clock is not INTOSC/LPRC and the device is not in Sleep; otherwise, uses INTOSC/LPRC 00 = Reserved bit 4-0 S1RWDTPS[4:0]: Run Mode Watchdog Timer Period Select bits 11111 = Divide by 231 = 2,147,483,648 11110 = Divide by 230 = 1,073,741,824 ... 00001 = Divide by 21 = 2 00000 = Divide by 20 = 1  2017-2019 Microchip Technology Inc. DS70005319D-page 691 dsPIC33CH128MP508 FAMILY REGISTER 21-28: FS1POR CONFIGURATION REGISTER (SLAVE) U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 15 bit 8 U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 23-0 x = Bit is unknown Unimplemented: Read as ‘1’ DS70005319D-page 692  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 21-29: FS1ICD CONFIGURATION REGISTER (SLAVE) U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 RP/O-1 U-1 R/PO-1 U-1 U-1 U-1 U-1 U-1 S1NOBTSWP — S1ISOLAT — — — — — bit 15 bit 8 r-1 U-1 U-1 U-1 U-1 U-1 — — — — — — R/PO-1 R/PO-1 S1ICS[1:0](1) bit 7 bit 0 Legend: PO = Program Once bit r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 23-16 Unimplemented: Read as ‘1’ bit 15 S1NOBTSWP: BOOTSWP Instruction Disable bit 1 = BOOTSWP instruction is disabled 0 = BOOTSWP instruction is enabled bit 14 Unimplemented: Read as ‘1’ bit 13 S1ISOLAT: Slave Core Isolation bit 1 = The Slave can operate (in Debug mode), even if the SLVEN bit in the MSI is zero 0 = The Slave can only operate if the SLVEN bit in the MSI is set bit 12-8 Unimplemented: Read as ‘1’ bit 7 Reserved: Maintain as ‘1’ bit 6-2 Unimplemented: Read as ‘1’ bit 1-0 S1ICS[1:0]: ICD Pin Placement Select bits(1) 11 = Slave ICD pins are S1PGC1/S1PGD1/S1MCLR1 10 = Slave ICD pins are S1PGC2/S1PGD2/S1MCLR2 01 = Slave ICD pins are S1PGC3/S1PGD3/S1MCLR3 00 = None Note 1: Only valid in Dual Debug mode (Master and Slave core debugged at the same time).  2017-2019 Microchip Technology Inc. DS70005319D-page 693 dsPIC33CH128MP508 FAMILY REGISTER 21-30: FS1DEVOPT CONFIGURATION REGISTER (SLAVE) U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 R/PO-1 R/PO-1 R/PO-1 U-1 U-1 U-1 U-1 U-1 S1MSRE S1SSRE S1SPI1PIN(1) — — — — — bit 15 bit 8 U-1 U-1 U-1 U-1 R/PO-1 U-1 U-1 U-1 — — — — S1ALTI2C1 — — — bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 23-16 Unimplemented: Read as ‘1’ bit 15 S1MSRE: Master Slave Reset Enable bit 1 = The Master software-oriented Reset events (Reset Opcode, Watchdog Timer Time-out Reset, Trap Reset, Illegal Instruction Reset) will also cause the Slave subsystem to reset 0 = The Master software-oriented Reset events (Reset Opcode, Watchdog Timer Time-out Reset, Trap Reset, Illegal Instruction Reset) will not cause the Slave subsystem to reset bit 14 S1SSRE: Slave Reset Enable bit 1 = Slave generated Resets will reset the Slave enable bit in the MSI module 0 = Slave generated Resets will not reset the Slave enable bit in the MSI module bit 13 S1SPI1PIN: Slave SPI1 Fast I/O Pad Disable bit(1) 1 = Slave SPI1 uses PPS (I/O remap) to make connects with device pins 0 = Slave SPI1 uses direct connections with specified device pins bit 12-4 Unimplemented: Read as ‘1’ bit 3 S1ALTI2C1: Alternate I2C1 Pin Mapping bit 1 = Default location for SCL1/SDA1 pins 0 = Alternate location for SCL1/SDA1 pins (ASCL1/ASDA1) bit 2-0 Unimplemented: Read as ‘1’ Note 1: Fixed pin option is only available for higher pin packages (48-pin, 64-pin and 80-pin). DS70005319D-page 694  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 21-31: FS1ALTREG CONFIGURATION REGISTER (SLAVE) U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 U-1 R/PO-1 — R/PO-1 R/PO-1 S1CTXT4[2:0] U-1 R/PO-1 — R/PO-1 R/PO-1 S1CTXT3[2:0] bit 15 bit 8 U-1 R/PO-1 — R/PO-1 R/PO-1 S1CTXT2[2:0] U-1 R/PO-1 — R/PO-1 R/PO-1 S1CTXT1[2:0] bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 23-15 Unimplemented: Read as ‘1’ bit 14-12 S1CTXT4[2:0]: Alternate Working Register Set #4 Interrupt Priority Level Selection bits 111 = Not assigned 110 = Alternate Register Set #4 is assigned to IPL Level 7 101 = Alternate Register Set #4 is assigned to IPL Level 6 100 = Alternate Register Set #4 is assigned to IPL Level 5 011 = Alternate Register Set #4 is assigned to IPL Level 4 010 = Alternate Register Set #4 is assigned to IPL Level 3 001 = Alternate Register Set #4 is assigned to IPL Level 2 000 = Alternate Register Set #4 is assigned to IPL Level 1 bit 11 Unimplemented: Read as ‘1’ bit 10-8 S1CTXT3[2:0]: Alternate Working Register Set #3 Interrupt Priority Level Selection bits 111 = Not assigned 110 = Alternate Register Set #3 is assigned to IPL Level 7 101 = Alternate Register Set #3 is assigned to IPL Level 6 100 = Alternate Register Set #3 is assigned to IPL Level 5 011 = Alternate Register Set #3 is assigned to IPL Level 4 010 = Alternate Register Set #3 is assigned to IPL Level 3 001 = Alternate Register Set #3 is assigned to IPL Level 2 000 = Alternate Register Set #3 is assigned to IPL Level 1 bit 7 Unimplemented: Read as ‘1’ bit 6-4 S1CTXT2[2:0]: Alternate Working Register Set #2 Interrupt Priority Level Selection bits 111 = Not assigned 110 = Alternate Register Set #2 is assigned to IPL Level 7 101 = Alternate Register Set #2 is assigned to IPL Level 6 100 = Alternate Register Set #2 is assigned to IPL Level 5 011 = Alternate Register Set #2 is assigned to IPL Level 4 010 = Alternate Register Set #2 is assigned to IPL Level 3 001 = Alternate Register Set #2 is assigned to IPL Level 2 000 = Alternate Register Set #2 is assigned to IPL Level 1 bit 3 Unimplemented: Read as ‘1’  2017-2019 Microchip Technology Inc. DS70005319D-page 695 dsPIC33CH128MP508 FAMILY REGISTER 21-31: FS1ALTREG CONFIGURATION REGISTER (SLAVE) (CONTINUED) bit 2-0 S1CTXT1[2:0]: Alternate Working Register Set #1 Interrupt Priority Level Selection bits 111 = Not assigned 110 = Alternate Register Set #1 is assigned to IPL Level 7 101 = Alternate Register Set #1 is assigned to IPL Level 6 100 = Alternate Register Set #1 is assigned to IPL Level 5 011 = Alternate Register Set #1 is assigned to IPL Level 4 010 = Alternate Register Set #1 is assigned to IPL Level 3 001 = Alternate Register Set #1 is assigned to IPL Level 2 000 = Alternate Register Set #1 is assigned to IPL Level 1 DS70005319D-page 696  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 21.2 Device Calibration and Identification The dsPIC33CH128MP508 devices have two Identification registers, near the end of configuration memory space, that store the Device ID (DEVID) and Device Revision (DEVREV). These registers are used to determine the mask, variant and manufacturing information about the device. These registers are read-only and are shown in Register 21-32 and Register 21-33. The PGAx and current source modules on the dsPIC33CH128MP508 family devices require Calibration Data registers to improve performance of the module over a wide operating range. These Calibration registers are read-only and are stored in configuration memory space. Prior to enabling the module, the calibration data must be read (TBLPAG and Table Read instruction) and loaded into their respective SFR registers. The device calibration addresses are shown in Table 21-4. TABLE 21-4: DEVICE CALIBRATION ADDRESSES(1) Calibration Address Bits 23-16 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Name Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 PGA1CAL 0xF8001C — — — — — — — — — PGA1 Calibration Data PGA2CAL 0xF8001E — — — — — — — — — PGA2 Calibration Data PGA3CAL 0xF80020 — — — — — — — — — ISRCCAL 0xF80012 — — — — — — — — — Note 1: PGA3 Calibration Data — — Current Source Calibration Data The calibration data must be copied into their respective registers prior to enabling the module.  2017-2019 Microchip Technology Inc. DS70005319D-page 697 dsPIC33CH128MP508 FAMILY REGISTER 21-32: DEVREV: DEVICE REVISION REGISTER R R R R R R R R DEVREV[23:16] bit 23 bit 16 R R R R R R R R DEVREV[15:8] bit 15 bit 8 R R R R R R R R DEVREV[7:0] bit 7 bit 0 Legend: R = Read-only bit bit 23-0 U = Unimplemented bit DEVREV[23:0]: Device Revision bits REGISTER 21-33: DEVID: DEVICE ID REGISTERS U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 R R R R R R R R FAMID[7:0] bit 15 bit 8 R R R R R R R R (1) DEV[7:0] bit 7 bit 0 Legend: R = Read-only bit U = Unimplemented bit bit 23-16 Unimplemented: Read as ‘1’ bit 15-8 FAMID[7:0]: Device Family Identifier bits 1000 0111 = dsPIC33CH128MP508 family bit 7-0 DEV[7:0]: Individual Device Identifier bits(1) Note 1: See Table 21-5 for the list of Device Identifier bits. DS70005319D-page 698  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 21-5: DEVICE VARIANTS DEVID[7:0] Device Name Core Devices with CAN FD 0x40 dsPIC33CH64MP502 Master 0xC0 dsPIC33CH64MP502S1 Slave 0x50 dsPIC33CH128MP502 Master 0xD0 dsPIC33CH128MP502S1 Slave 0x41 dsPIC33CH64MP503 Master 0xC1 dsPIC33CH64MP503S1 Slave 0x51 dsPIC33CH128MP503 Master 0xD1 dsPIC33CH128MP503S1 Slave 0x42 dsPIC33CH64MP505 Master 0xC2 dsPIC33CH64MP505S1 Slave 0x52 dsPIC33CH128MP505 Master 0xD2 dsPIC33CH128MP505S1 Slave 0x43 dsPIC33CH64MP506 Master 0xC3 dsPIC33CH64MP506S1 Slave 0x53 dsPIC33CH128MP506 Master 0xD3 dsPIC33CH128MP506S1 Slave 0x44 dsPIC33CH64MP508 Master 0xC4 dsPIC33CH64MP508S1 Slave 0x54 dsPIC33CH128MP508 Master 0xD4 dsPIC33CH128MP508S1 Slave  2017-2019 Microchip Technology Inc. DS70005319D-page 699 dsPIC33CH128MP508 FAMILY TABLE 21-5: DEVICE VARIANTS (CONTINUED) DEVID[7:0] Device Name Core Devices without CAN FD 0x00 dsPIC33CH64MP202 0x80 dsPIC33CH64MP202S1 Slave 0x10 dsPIC33CH128MP202 Master 0x90 dsPIC33CH128MP202S1 Slave 0x01 dsPIC33CH64MP203 Master 0x81 dsPIC33CH64MP203S1 Slave 0x11 dsPIC33CH128MP203 Master 0x91 dsPIC33CH128MP203S1 Slave 0x02 dsPIC33CH64MP205 Master 0x82 dsPIC33CH64MP205S1 Slave 0x12 dsPIC33CH128MP205 Master 0x92 dsPIC33CH128MP205S1 Slave 0x03 dsPIC33CH64MP206 Master 0x83 dsPIC33CH64MP206S1 Slave 0x13 dsPIC33CH128MP206 Master 0x93 dsPIC33CH128MP206S1 Slave 0x04 dsPIC33CH64MP208 Master 0x84 dsPIC33CH64MP208S1 Slave 0x14 dsPIC33CH128MP208 Master 0x94 dsPIC33CH128MP208S1 Slave DS70005319D-page 700 Master  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 21.3 User OTP Memory The dsPIC33CH128MP508 family devices contain 64 One-Time-Programmable (OTP) double words, located at addresses, 801700h through 8017FEh. Each 48-bit OTP double word can only be written one time. The OTP Words can be used for storing checksums, code revisions, manufacturing dates, manufacturing lot numbers or any other application-specific information. FIGURE 21-1: The OTP area is not cleared by any erase command. This memory can be written only once. 21.4 On-Chip Voltage Regulators All of the dsPIC33CH128MP508 family devices have a capacitorless, internal voltage regulator to supply power to the core at 1.2V (typical). A pair of voltage regulators, VREG1 and VREG2 together, provide power for the core. The PLL is powered using a separate regulator, VREGPLL, as shown in Figure 21-1. INTERNAL REGULATOR VSS VDD VREG1 Master VREG2 Slave 0.1 µF Ceramic Master PLL VREGPLL Slave PLL AVDD 0.1 µF Ceramic  2017-2019 Microchip Technology Inc. AVSS Band Gap Reference DS70005319D-page 701 dsPIC33CH128MP508 FAMILY 21.5 Regulator Control and Sleep Mode As shown in Register 21-34, there are two control bits, VREGxOV[1:0], to control the output voltages of these regulators. As shown in Figure 21-1, both VREG1 and VREG2 together, share the total load for the Master and Slave. Before going to Sleep, the voltage regulator should be changed to 1V (or 0.8V). The voltage regulators communicate to the Slave or Master depending on the scenario below. The PLL for the Master and Slave is powered using a separate regulator, as shown for VREG3 (VREGPLL). The output voltages of these regulators can be controlled by the user, which gives eligibility to save power during Sleep mode. REGISTER 21-34: VREGCON: VOLTAGE REGULATOR CONTROL REGISTER r-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 — — R/W-0 R/W-0 R/W-0 VREG3OV1 VREG3OV0 VREG2OV1 R/W-0 R/W-0 R/W-0 VREG2OV0 VREG1OV1 VREG1OV0 bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 Reserved: Maintain as ‘0’ bit 14-6 Unimplemented: Read as ‘0’ bit 5-4 VREG3OV[1:0]: Low-Power Mode Enable bits 11/00 = VOUT = 1.5 * VBG = 1.2V 10 = VOUT = 1.25 * VBG = 1.0V 01 = VOUT = VBG = 0.8V bit 3-2 VREG2OV[1:0]: Low-Power Mode Enable bits 11/00 = VOUT = 1.5 * VBG = 1.2V 10 = VOUT = 1.25 * VBG = 1.0V 01 = VOUT = VBG = 0.8V bit 1-0 VREG1OV[1:0]: Low-Power Mode Enable bits 11/00 = VOUT = 1.5 * VBG = 1.2V 10 = VOUT = 1.25 * VBG = 1.0V 01 = VOUT = VBG = 0.8V DS70005319D-page 702 x = Bit is unknown  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 21.6 Limiting Dynamic Load Changes The device start-up and shutdown must be staged to minimize large load steps. 1. 2. 3. 4. 5. 6. 7. 8. Start the device in FRC or Oscillator mode and enable the PLL option (if required). Master enables Auxiliary PLL, if required, for the PWM or DAC modules. Master initializes the Slave PRAM with the Slave programming. The Master enables the PWM generators in a sequential manner (as required). Master enables the Slave processor. Slave starts in FRC or Oscillator mode and enables the PLL option (if required). The Slave enables its Auxiliary PLL (if required) for the Slave’s DAC or PWM modules. The Slave enables its PWM generators in a sequential manner (as required). When powering down the device to Sleep or Idle mode, the user should follow this general sequence in reverse. 21.7 Brown-out Reset (BOR) The Brown-out Reset (BOR) module is based on an internal voltage reference circuit that monitors the regulated supply voltage. The main purpose of the BOR module is to generate a device Reset when a brown-out condition occurs. Brown-out conditions are generally caused by glitches on the AC mains (for example, missing portions of the AC cycle waveform due to bad power transmission lines or voltage sags due to excessive current draw when a large inductive load is turned on). A BOR generates a Reset pulse which resets the device. The BOR selects the clock source based on the device Configuration bit selections. If an Oscillator mode is selected, the BOR activates the Oscillator Start-up Timer (OST). The system clock is held until OST expires. If the PLL is used, the clock is held until the LOCK bit (OSCCON[5]) is ‘1’. Concurrently, the PWRT Time-out (TPWRT) is applied before the internal Reset is released. If TPWRT = 0 and a crystal oscillator is being used, then a nominal delay of TFSCM is applied. The total delay in this case is TFSCM. Refer to Parameter SY35 in Table 24-32 of Section 24.0 “Electrical Characteristics” for specific TFSCM values. The BOR status bit (RCON[1]) is set to indicate that a BOR has occurred. The BOR circuit continues to operate while in Sleep or Idle mode and resets the device should VDD fall below the BOR threshold voltage.  2017-2019 Microchip Technology Inc. DS70005319D-page 703 dsPIC33CH128MP508 FAMILY 21.8 Dual Watchdog Timer (WDT) Note 1: This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to “Dual Watchdog Timer”, (www.microchip.com/DS70005250) in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). 2: The WDT is identical for both Master core and Slave core. The x is common for both Master core and Slave core (where the x represents the number of the specific module being addressed). The number of WDT modules available on the Master and Slaves is different and they are located in different SFR locations. 3: All associated register names are the same on the Master core and the Slave core. The Slave code will be developed in a separate project in MPLAB® X IDE with the device selection, dsPIC33CH128MP508S1, where the S1 indicates the Slave device. Table 21-6 shows an overview of the WDT module. TABLE 21-6: DUAL WDT MODULE OVERVIEW Number of WDT Modules Identical (Modules) Master Core 1 Yes Slave Core 1 Yes The dsPIC33 dual Watchdog Timer (WDT) is described in this section. Refer to Figure 21-2 for a block diagram of the WDT. The WDT, when enabled, operates from the internal Low-Power RC (LPRC) Oscillator clock source or a selectable clock source in Run mode. The WDT can be used to detect system software malfunctions by resetting the device if the WDT is not cleared periodically in software. The WDT can be configured in Windowed mode or Non-Windowed mode. Various WDT time-out periods can be selected using the WDT postscaler. The WDT can also be used to wake the device from Sleep or Idle mode (Power Save mode). If the WDT expires and issues a device Reset, the WTDO bit of the RCON register (Register 21-37) will be set. The following are some of the key features of the WDT modules: • Configuration or Software Controlled • Separate User-Configurable Time-out Periods for Run and Sleep/Idle • Can Wake the Device from Sleep or Idle • User-Selectable Clock Source in Run mode • Operates from LPRC in Sleep/Idle mode Note: DS70005319D-page 704 While executing a clock switch, the WDT will not be reset. It is recommended to reset the WDT prior to executing a clock switch instruction.  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 21-2: WATCHDOG TIMER BLOCK DIAGRAM Power Save Mode WDT LPRC Oscillator Power Save CLKSEL[1:0] FCY (FOSC/2) Reserved FRC Oscillator LPRC Oscillator ON 32-Bit Counter Power Save Comparator Wake-up and NMI Reset SLPDIV[4:0] Run Mode WDT 00 01 Power Save 32-Bit Counter Comparator NMI and Start NMI Counter 10 11 Reset RUNDIV[4:0] WDTCLRKEY[15:0] = 5743h ON All Resets Clock Switch  2017-2019 Microchip Technology Inc. DS70005319D-page 705 dsPIC33CH128MP508 FAMILY 21.9 Watchdog Timer Control Registers REGISTER 21-35: WDTCONL: WATCHDOG TIMER CONTROL REGISTER LOW R/W-0 U-0 U-0 ON(1,2) — — R-y R-y R-y R-y R-y RUNDIV[4:0](3) bit 15 bit 8 R R CLKSEL1(3,5) CLKSEL0(3,5) R-y R-y R-y R-y R-y HS/R/W-0 SLPDIV4(3) SLPDIV3(3) SLPDIV2(3) SLPDIV1(3) SLPDIV0(3) WDTWINEN(4) bit 7 bit 0 Legend: HS = Hardware Settable bit y = Value from Configuration bit on POR R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ON: Watchdog Timer Enable bit(1,2) 1 = Enables the Watchdog Timer if it is not enabled by the device configuration 0 = Disables the Watchdog Timer if it was enabled in software bit 14-13 Unimplemented: Read as ‘0’ bit 12-8 RUNDIV[4:0]: WDT Run Mode Postscaler Status bits(3) 11111 = Divide by 231 = 2,147,483,648 11110 = Divide by 230 = 1,073,741,824 ... 00001 = Divide by 21 = 2 00000 = Divide by 20 = 1 bit 7-6 CLKSEL[1:0]: WDT Run Mode Clock Select Status bits(3,5) 11 = LPRC Oscillator 10 = FRC Oscillator 01 = Reserved 00 = FCY (FOSC/2) bit 5-1 SLPDIV[4:0]: Sleep and Idle Mode WDT Postscaler Status bits(3) 11111 = Divide by 231 = 2,147,483,648 11110 = Divide by 230 = 1,073,741,824 ... 00001 = Divide by 21 = 2 00000 = Divide by 20 = 1 bit 0 WDTWINEN: Watchdog Timer Window Enable bit(4) 1 = Enables Window mode 0 = Disables Window mode Note 1: 2: 3: 4: 5: A read of this bit will result in a ‘1’ if the WDT is enabled by the device configuration or by software. The user’s software should not read or write to the peripheral’s SFRs in the SYSCLK cycle immediately following the instruction that clears the module’s ON bit. These bits reflect the value of the Configuration bits. The WDTWINEN bit reflects the status of the Configuration bit if the bit is set. If the bit is cleared, the value is controlled by software. The available clock sources are device-dependent. DS70005319D-page 706  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY REGISTER 21-36: WDTCONH: WATCHDOG TIMER CONTROL REGISTER HIGH W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 WDTCLRKEY[15:8] bit 15 bit 8 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 WDTCLRKEY[7:0] bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 x = Bit is unknown WDTCLRKEY[15:0]: Watchdog Timer Clear Key bits To clear the Watchdog Timer to prevent a time-out, software must write the value, 0x5743, to this location using a single 16-bit write.  2017-2019 Microchip Technology Inc. DS70005319D-page 707 dsPIC33CH128MP508 FAMILY REGISTER 21-37: RCON: RESET CONTROL REGISTER(1) R/W-0 TRAPR R/W-0 IOPUWR U-0 — U-0 — U-0 — U-0 — R/W-0 CM R/W-0 VREGS bit 15 bit 8 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-1 R/W-1 EXTR bit 7 SWR — WDTO SLEEP IDLE BOR POR bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 bit 14 TRAPR: Trap Reset Flag bit 1 = A Trap Conflict Reset has occurred 0 = A Trap Conflict Reset has not occurred IOPUWR: Illegal Opcode or Uninitialized W Register Access Reset Flag bit 1 = An illegal opcode detection, an illegal address mode or Uninitialized W register used as an Address Pointer caused a Reset 0 = An Illegal Opcode or Uninitialized W register Reset has not occurred bit 13-10 bit 9 Unimplemented: Read as ‘0’ CM: Configuration Mismatch Flag bit 1 = A Configuration Mismatch Reset has occurred 0 = A Configuration Mismatch Reset has not occurred bit 8 VREGS: Voltage Regulator Standby During Sleep bit 1 = Voltage regulator is active during Sleep 0 = Voltage regulator goes into Standby mode during Sleep EXTR: External Reset (MCLR) Pin bit 1 = A Master Clear (pin) Reset has occurred 0 = A Master Clear (pin) Reset has not occurred bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 Note 1: x = Bit is unknown SWR: Software RESET (instruction) Flag bit 1 = A RESET instruction has been executed 0 = A RESET instruction has not been executed Unimplemented: Read as ‘0’ WDTO: Watchdog Timer Time-out Flag bit 1 = WDT time-out has occurred 0 = WDT time-out has not occurred SLEEP: Wake from Sleep Flag bit 1 = Device was in Sleep mode 0 = Device was not in Sleep mode IDLE: Wake from Idle Flag bit 1 = Device was in Idle mode 0 = Device was not in Idle mode BOR: Brown-out Reset Flag bit 1 = Brown-out Reset has occurred 0 = Brown-out Reset has not occurred POR: Power-on Reset Flag bit 1 = Power-on Reset has occurred 0 = Power-on Reset has not occurred All of the Reset status bits can be set or cleared in software. Setting one of these bits in software does not cause a device Reset. DS70005319D-page 708  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 21.10 JTAG Interface 21.12 In-Circuit Debugger The dsPIC33CH128MP508 family devices implement a JTAG interface, which supports boundary scan device testing. Detailed information on this interface will be provided in future revisions of this document. When MPLAB® ICD 3 or the REAL ICE™ emulator is selected as a debugger, the in-circuit debugging functionality is enabled. This function allows simple debugging functions when used with MPLAB IDE. Debugging functionality is controlled through the PGCx (Emulation/Debug Clock) and PGDx (Emulation/Debug Data) pin functions. Note: 21.11 Refer to “Programming and Diagnostics” (www.microchip.com/DS70608) in the “dsPIC33/PIC24 Family Reference Manual” for further information on usage, configuration and operation of the JTAG interface. In-Circuit Serial Programming™ (ICSP™) The dsPIC33CH128MP508 family devices can be serially programmed while in the end application circuit. This is done with two lines for clock and data, and three other lines for power, ground and the programming sequence. Serial programming allows customers to manufacture boards with unprogrammed devices and then program the device just before shipping the product. Serial programming also allows the most recent firmware or a custom firmware to be programmed. Refer to the “dsPIC33CH128MP508 Family Flash Programming Specification” (DS70005285) for details about In-Circuit Serial Programming (ICSP). Any of the three pairs of programming clock/data pins can be used: • PGC1 and PGD1 • PGC2 and PGD2 • PGC3 and PGD3 Note: Both Master core and Slave core can be used with MPLAB® ICD to debug at the same time. There are PGCx and PGDx pins dedicated for the Master core and Slave core (S1PGCx and S1PGDx) to make this possible. MCLR is the same for programming the Master core and the Slave core. S1MCLRx is used only when the Master and Slave are debugged simultaneously. Any of the three pairs of debugging clock/data pins can be used: • PGC1 and PGD1 Master Debug or Slave Debug • PGC2 and PGD2 Master Debug or Slave Debug • PGC3 and PGD3 Master Debug or Slave Debug for debugging Master and Slave simultaneously, two MPLAB ICD debuggers or the REAL ICE™ emulator are required. This mode of debugging, where the Master and Slave are simultaneously debugged, is called the Dual Debug mode. S1MCLRx and S1PGCx/S1PGDx are used only in Dual Debug mode. The Dual Debug mode of operation needs the following PGCx/PGDx pins: • MCLR, PGC1 and PGD1 for Master Debug, and S1MCLR1, S1PGC1 and S1PGD1 for Slave Debug • MCLR, PGC2 and PGD2 for Master Debug, and S1MCLR2, S1PGC2 and S1PGD2 for Slave Debug • MCLR, PGC3 and PGD3 for Master Debug, and S1MCLR3, S1PGC3 and S1PGD3 for Slave Debug To use the in-circuit debugger function of the device, the design must implement ICSP connections to MCLR, VDD, VSS and the PGCx/PGDx pin pair. In addition, when the feature is enabled, some of the resources are not available for general use. These resources include the first 80 bytes of data RAM and two or five (in Dual Debug) I/O pins (PGCx and PGDx). There are three modes of debugging the dual core family of dsPIC33CH128MP508: 1. 2. 3. Master Only Debug Slave Only Debug Dual Debug 21.12.1 MASTER ONLY DEBUG In Master Only Debug, only the Master project will be debugged. There is no project for Slave or no Slave code. The main project will be for dsPIC33CHXXXMP50X/20X and the user has to use MCLR and PGCx/PGDx for debugging. This is similar to debugging any single core existing device.  2017-2019 Microchip Technology Inc. DS70005319D-page 709 dsPIC33CH128MP508 FAMILY 21.12.2 SLAVE ONLY DEBUG In the Slave Only Debug mode, the user will need two projects. One project is the Master project with dsPIC33CHXXXMP50X/20X as the device. This is called a Master Stub and is required to provide the configuration information to the Slave. The Slave does not have its own Configuration bits. The Configuration bits reside in the Master Flash. The Master Stub will be small code used to provide the Configuration bits for the Slave. The Master Stub is first programed to the Master Flash using MCLR, PGCx and PGDx. Once the Master Stub is programmed in the Master Flash, the user has to open a new project with dsPIC33CHXXXMP50X/20XS1 (the S1 indicates the Slave device). The same MCLR and PGCx/PGDx, or different PGCx/PGDx, can be used for debugging the Slave. Now the Slave can be debugged like any other single core device. 21.12.3 DUAL DEBUG (BOTH MASTER AND SLAVE ARE DEBUGGED) In this Debug mode, two debug tools are required: one for Master and one for Slave. In the Dual Debug mode, the user needs two projects. One project is the Master project with dsPIC33CHXXXMP50X/20X as the device. Configuration bits for the Master, as well as the Slave, will be part of this project. The S1ISOLAT bit can be set and the Master project can be debugged like any other existing single core device. The Master can be debugged using MCLR, PGCx and PGDx. Once the Master has started the debug process, the user has to open a new project with dsPIC33CHXXXMP50X/ 20XS1 (the S1 indicates the Slave device). Connect the project using S1MCLRx and S1PGCx/S1PGDx, and start debugging the Slave project. DS70005319D-page 710 21.13 Code Protection and CodeGuard™ Security – Master Flash dsPIC33CH128MP508 family devices offer multiple levels of security for protecting individual intellectual property. The program Flash protection can be broken up into three segments: Boot Segment (BS), General Segment (GS) and Configuration Segment (CS). Boot Segment has the highest security privilege and can be thought to have limited restrictions when accessing other segments. General Segment has the least security and is intended for the end user system code. Configuration Segment contains only the device user configuration data, which are located at the end of the program memory space. The code protection features are controlled by the Configuration registers, FSEC and FBSLIM. The FSEC register controls the code-protect level for each segment and if that segment is write-protected. The size of BS and GS will depend on the BSLIM[12:0] bits setting and if the Alternate Interrupt Vector Table (AIVT) is enabled. The BSLIM[12:0] bits define the number of pages for BS with each page containing 1024 IW. The smallest BS size is one page, which will consist of the Interrupt Vector Table (IVT) and 512 IW of code protection. If the AIVT is enabled, the last page of BS will contain the AIVT and will not contain any BS code. With AIVT enabled, the smallest BS size is now two pages (2048 IW), with one page for the IVT and BS code, and the other page for the AIVT. Write protection of the BS does not cover the AIVT. The last page of BS can always be programmed or erased by BS code. The General Segment will start at the next page and will consume the rest of program Flash, except for the Flash Configuration Words. The IVT will assume GS security only if BS is not enabled. The IVT is protected from being programmed or page erased when either security segment has enabled write protection.  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY The different device security segments are shown in Figure 21-3. Here, all three segments are shown, but are not required. If only basic code protection is required, then GS can be enabled independently or combined with CS, if desired. FIGURE 21-3: SECURITY SEGMENTS EXAMPLE 0x000000 IVT IVT and AIVT Assume BS Protection 0x000200 BS AIVT + 512 IW(2) BSLIM[12:0] 21.14 Code Protection and CodeGuard™ Security – Slave PRAM The dsPIC33CH128MP508S1 family Slave PRAM inherits its security configuration from the Master GSS[1:0] and GWRP Configuration bit settings. The Slave PRAM does not have a BS or CS segment. All user code space is considered GS, including the IVT. Therefore, there are no specific segment read and write permissions to consider. If either the GSSx or GWRP bits are enabled, ICSP entry directly to the Slave PRAM is inhibited. This prevents reading, programming and debugging the Slave PRAM when the Master Flash GS is code-protected. Master to Slave Image Loading is always allowed, regardless of any code protection settings. GS CS(1) 0x00B000 Note 1: 2: If CS is write-protected, the last page (GS + CS) of program memory will be protected from an erase condition. The last half (256 IW) of the last page of BS is unusable program memory.  2017-2019 Microchip Technology Inc. DS70005319D-page 711 dsPIC33CH128MP508 FAMILY NOTES: DS70005319D-page 712  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 22.0 Note: INSTRUCTION SET SUMMARY This data sheet summarizes the features of the dsPIC33CH128MP508 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to the related section in the “dsPIC33/PIC24 Family Reference Manual”, which is available from the Microchip website (www.microchip.com). The dsPIC33CH instruction set is almost identical to that of the dsPIC30F and dsPIC33F. Most instructions are a single program memory word (24 bits). Only three instructions require two program memory locations. Each single-word instruction is a 24-bit word, divided into an 8-bit opcode, which specifies the instruction type and one or more operands, which further specify the operation of the instruction. The instruction set is highly orthogonal and is grouped into five basic categories: • • • • • Word or byte-oriented operations Bit-oriented operations Literal operations DSP operations Control operations Table 22-1 lists the general symbols used in describing the instructions. The dsPIC33 instruction set summary in Table 22-2 lists all the instructions, along with the status flags affected by each instruction. Most word or byte-oriented W register instructions (including barrel shift instructions) have three operands: • The first source operand, which is typically a register ‘Wb’ without any address modifier • The second source operand, which is typically a register ‘Ws’ with or without an address modifier • The destination of the result, which is typically a register ‘Wd’ with or without an address modifier However, word or byte-oriented file register instructions have two operands: • The file register specified by the value ‘f’ • The destination, which could be either the file register ‘f’ or the W0 register, which is denoted as ‘WREG’  2017-2019 Microchip Technology Inc. Most bit-oriented instructions (including simple rotate/ shift instructions) have two operands: • The W register (with or without an address modifier) or file register (specified by the value of ‘Ws’ or ‘f’) • The bit in the W register or file register (specified by a literal value or indirectly by the contents of register ‘Wb’) The literal instructions that involve data movement can use some of the following operands: • A literal value to be loaded into a W register or file register (specified by ‘k’) • The W register or file register where the literal value is to be loaded (specified by ‘Wb’ or ‘f’) However, literal instructions that involve arithmetic or logical operations use some of the following operands: • The first source operand, which is a register ‘Wb’ without any address modifier • The second source operand, which is a literal value • The destination of the result (only if not the same as the first source operand), which is typically a register ‘Wd’ with or without an address modifier The MAC class of DSP instructions can use some of the following operands: • The accumulator (A or B) to be used (required operand) • The W registers to be used as the two operands • The X and Y address space prefetch operations • The X and Y address space prefetch destinations • The accumulator write-back destination The other DSP instructions do not involve any multiplication and can include: • The accumulator to be used (required) • The source or destination operand (designated as Wso or Wdo, respectively) with or without an address modifier • The amount of shift specified by a W register ‘Wn’ or a literal value The control instructions can use some of the following operands: • A program memory address • The mode of the Table Read and Table Write instructions DS70005319D-page 713 dsPIC33CH128MP508 FAMILY Most instructions are a single word. Certain double-word instructions are designed to provide all the required information in these 48 bits. In the second word, the 8 MSbs are ‘0’s. If this second word is executed as an instruction (by itself), it executes as a NOP. The double-word instructions execute in two instruction cycles. Most single-word instructions are executed in a single instruction cycle, unless a conditional test is true or the Program Counter is changed as a result of the instruction, or a PSV or Table Read is performed. In TABLE 22-1: these cases, the execution takes multiple instruction cycles, with the additional instruction cycle(s) executed as a NOP. Certain instructions that involve skipping over the subsequent instruction require either two or three cycles if the skip is performed, depending on whether the instruction being skipped is a single-word or twoword instruction. Moreover, double-word moves require two cycles. Note: For more details on the instruction set, refer to the “16-Bit MCU and DSC Programmer’s Reference Manual” (DS70000157). SYMBOLS USED IN OPCODE DESCRIPTIONS Field #text Description Means literal defined by “text” (text) Means “content of text” [text] Means “the location addressed by text” {} Optional field or operation a  {b, c, d} a is selected from the set of values b, c, d [n:m] Register bit field .b Byte mode selection .d Double-Word mode selection .S Shadow register select .w Word mode selection (default) Acc One of two accumulators {A, B} AWB Accumulator Write-Back Destination Address register {W13, [W13]+ = 2} bit4 4-bit bit selection field (used in word-addressed instructions) {0...15} C, DC, N, OV, Z MCU Status bits: Carry, Digit Carry, Negative, Overflow, Sticky Zero Expr Absolute address, label or expression (resolved by the linker) f File register address {0x0000...0x1FFF} lit1 1-bit unsigned literal {0,1} lit4 4-bit unsigned literal {0...15} lit5 5-bit unsigned literal {0...31} lit8 8-bit unsigned literal {0...255} lit10 10-bit unsigned literal {0...255} for Byte mode, {0:1023} for Word mode lit14 14-bit unsigned literal {0...16384} lit16 16-bit unsigned literal {0...65535} lit23 23-bit unsigned literal {0...8388608}; LSb must be ‘0’ None Field does not require an entry, can be blank OA, OB, SA, SB DSP Status bits: ACCA Overflow, ACCB Overflow, ACCA Saturate, ACCB Saturate PC Program Counter Slit10 10-bit signed literal {-512...511} Slit16 16-bit signed literal {-32768...32767} Slit6 6-bit signed literal {-16...16} Wb Base W register {W0...W15} Wd Destination W register { Wd, [Wd], [Wd++], [Wd--], [++Wd], [--Wd] } Wdo Destination W register  { Wnd, [Wnd], [Wnd++], [Wnd--], [++Wnd], [--Wnd], [Wnd+Wb] } Wm,Wn Dividend, Divisor Working register pair (direct addressing) DS70005319D-page 714  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 22-1: SYMBOLS USED IN OPCODE DESCRIPTIONS (CONTINUED) Field Description Wm*Wm Multiplicand and Multiplier Working register pair for Square instructions  {W4 * W4,W5 * W5,W6 * W6,W7 * W7} Wm*Wn Multiplicand and Multiplier Working register pair for DSP instructions  {W4 * W5,W4 * W6,W4 * W7,W5 * W6,W5 * W7,W6 * W7} Wn One of 16 Working registers {W0...W15} Wnd One of 16 Destination Working registers {W0...W15} Wns One of 16 Source Working registers {W0...W15} WREG W0 (Working register used in file register instructions) Ws Source W register { Ws, [Ws], [Ws++], [Ws--], [++Ws], [--Ws] } Wso Source W register  { Wns, [Wns], [Wns++], [Wns--], [++Wns], [--Wns], [Wns+Wb] } Wx X Data Space Prefetch Address register for DSP instructions  {[W8] + = 6, [W8] + = 4, [W8] + = 2, [W8], [W8] – = 6, [W8] – = 4, [W8] – = 2, [W9] + = 6, [W9] + = 4, [W9] + = 2, [W9], [W9] – = 6, [W9] – = 4, [W9] – = 2, [W9 + W12], none} Wxd X Data Space Prefetch Destination register for DSP instructions {W4...W7} Wy Y Data Space Prefetch Address register for DSP instructions  {[W10] + = 6, [W10] + = 4, [W10] + = 2, [W10], [W10] – = 6, [W10] – = 4, [W10] – = 2, [W11] + = 6, [W11] + = 4, [W11] + = 2, [W11], [W11] – = 6, [W11] – = 4, [W11] – = 2, [W11 + W12], none} Wyd Y Data Space Prefetch Destination register for DSP instructions {W4...W7} Note: In dsPIC33CH128MP508 devices, read and Read-Modify-Write (RMW) operations on non-CPU Special Function Registers require an additional cycle when compared to dsPIC30F, dsPIC33F, PIC24F and PIC24H devices  2017-2019 Microchip Technology Inc. DS70005319D-page 715 dsPIC33CH128MP508 FAMILY TABLE 22-2: INSTRUCTION SET OVERVIEW Base Assembly Instr Mnemonic # 1 2 3 4 5 6 7 8 Note ADD ADDC AND ASR BCLR BFEXT BFINS BOOTSWP 1: 2: 3: Assembly Syntax Description # of Words # of Cycles(1) Status Flags Affected OA,OB,SA,SB ADD Acc Add Accumulators 1 1 ADD f f = f + WREG 1 1 C,DC,N,OV,Z ADD f,WREG WREG = f + WREG 1 1 C,DC,N,OV,Z ADD #lit10,Wn Wd = lit10 + Wd 1 1 C,DC,N,OV,Z ADD Wb,Ws,Wd Wd = Wb + Ws 1 1 C,DC,N,OV,Z ADD Wb,#lit5,Wd Wd = Wb + lit5 1 1 C,DC,N,OV,Z OA,OB,SA,SB ADD Wso,#Slit4,Acc 16-bit Signed Add to Accumulator 1 1 ADDC f f = f + WREG + (C) 1 1 C,DC,N,OV,Z ADDC f,WREG WREG = f + WREG + (C) 1 1 C,DC,N,OV,Z ADDC #lit10,Wn Wd = lit10 + Wd + (C) 1 1 C,DC,N,OV,Z ADDC Wb,Ws,Wd Wd = Wb + Ws + (C) 1 1 C,DC,N,OV,Z ADDC Wb,#lit5,Wd Wd = Wb + lit5 + (C) 1 1 C,DC,N,OV,Z AND f f = f .AND. WREG 1 1 N,Z AND f,WREG WREG = f .AND. WREG 1 1 N,Z AND #lit10,Wn Wd = lit10 .AND. Wd 1 1 N,Z AND Wb,Ws,Wd Wd = Wb .AND. Ws 1 1 N,Z AND Wb,#lit5,Wd Wd = Wb .AND. lit5 1 1 N,Z ASR f f = Arithmetic Right Shift f 1 1 C,N,OV,Z ASR f,WREG WREG = Arithmetic Right Shift f 1 1 C,N,OV,Z ASR Ws,Wd Wd = Arithmetic Right Shift Ws 1 1 C,N,OV,Z ASR Wb,Wns,Wnd Wnd = Arithmetic Right Shift Wb by Wns 1 1 N,Z ASR Wb,#lit5,Wnd Wnd = Arithmetic Right Shift Wb by lit5 1 1 N,Z BCLR f,#bit4 Bit Clear f 1 1 None BCLR Ws,#bit4 Bit Clear Ws 1 1 None BFEXT bit4,wid5,Ws,Wb Bit Field Extract from Ws to Wb 2 2 None BFEXT bit4,wid5,f,Wb Bit Field Extract from f to Wb 2 2 None BFINS bit4,wid5,Wb,Ws Bit Field Insert from Wb into Ws 2 2 None BFINS bit4,wid5,Wb,f Bit Field Insert from Wb into f 2 2 None BFINS bit4,wid5,lit8,Ws Bit Field Insert from #lit8 to Ws 2 2 None Swap the Active and Inactive Program Flash Space 1 2 None BOOTSWP Read and Read-Modify-Write (e.g., bit operations and logical operations) on non-CPU SFRs incur an additional instruction cycle. Cycle times for Slave core are different for Master core, as shown in 2. For dsPIC33CH128MP508 devices, the divide instructions must be preceded with a “REPEAT #5” instruction, such that they are executed six consecutive times DS70005319D-page 716  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 22-2: INSTRUCTION SET OVERVIEW (CONTINUED) Base Assembly Instr Mnemonic # 9 BRA Assembly Syntax Description # of Words # of Cycles(1) Status Flags Affected BRA C,Expr Branch if Carry 1 1 (4)/1 (2)(2) None BRA GE,Expr Branch if Greater Than or Equal 1 1 (4)/1 (2)(2) None BRA GEU,Expr Branch if unsigned Greater Than or Equal 1 1 (4)/1 (2)(2) None BRA GT,Expr Branch if Greater Than 1 1 (4)/1 (2)(2) None BRA GTU,Expr Branch if Unsigned Greater Than 1 1 (4)/1 (2)(2) None BRA LE,Expr Branch if Less Than or Equal 1 1 (4)/1 (2)(2) None BRA LEU,Expr Branch if Unsigned Less Than or Equal 1 1 (4)/1 (2)(2) None BRA LT,Expr Branch if Less Than 1 1 (4)/1 (2)(2) None BRA LTU,Expr Branch if Unsigned Less Than 1 1 (4)/1 (2)(2) None BRA N,Expr Branch if Negative 1 1 (4)/1 (2)(2) None BRA NC,Expr Branch if Not Carry 1 1 (4)/1 (2)(2) None BRA NN,Expr Branch if Not Negative 1 1 (4)/1 (2)(2) None BRA NOV,Expr Branch if Not Overflow 1 1 (4)/1 (2)(2) None BRA NZ,Expr Branch if Not Zero 1 1 (4)/1 (2)(2) None BRA OA,Expr Branch if Accumulator A Overflow 1 1 (4)/1 (2)(2) None BRA OB,Expr Branch if Accumulator B Overflow 1 1 (4)/1 (2)(2) None BRA OV,Expr Branch if Overflow 1 1 (4)/1 (2)(2) None BRA SA,Expr Branch if Accumulator A Saturated 1 1 (4)/1 (2)(2) None BRA SB,Expr Branch if Accumulator B Saturated 1 1 (4)/1 (2)(2) None BRA Expr Branch Unconditionally 1 4/2(2) None BRA Z,Expr Branch if Zero 1 1 (4)/1 (2)(2) None BRA Wn Computed Branch 1 4 None 10 BREAK BREAK Stop User Code Execution 1 1 None 11 BSET BSET f,#bit4 Bit Set f 1 1 None Ws,#bit4 Bit Set Ws 1 1 None 12 BSW BSW.C Ws,Wb Write C Bit to Ws[Wb] 1 1 None BSW.Z Ws,Wb Write Z Bit to Ws[Wb] 1 1 None f,#bit4 Bit Toggle f 1 1 None 13 BTG BTG BTG Ws,#bit4 Bit Toggle Ws 1 1 None 14 BTSC BTSC f,#bit4 Bit Test f, Skip if Clear 1 1 (2 or 3) None BTSC Ws,#bit4 Bit Test Ws, Skip if Clear 1 1 (2 or 3) None BTSS f,#bit4 Bit Test f, Skip if Set 1 1 (2 or 3) None BTSS Ws,#bit4 Bit Test Ws, Skip if Set 1 1 (2 or 3) None BTST f,#bit4 Bit Test f 1 1 Z BTST.C Ws,#bit4 Bit Test Ws to C 1 1 C BTST.Z Ws,#bit4 Bit Test Ws to Z 1 1 Z BTST.C Ws,Wb Bit Test Ws[Wb] to C 1 1 C 15 16 17 18 Note BTSS BTST BTSTS CALL 1: 2: 3: BTST.Z Ws,Wb Bit Test Ws[Wb] to Z 1 1 Z BTSTS f,#bit4 Bit Test then Set f 1 1 Z BTSTS.C Ws,#bit4 Bit Test Ws to C, then Set 1 1 C BTSTS.Z Ws,#bit4 Bit Test Ws to Z, then Set 1 1 Z CALL lit23 Call Subroutine 2 4/(2)(2) SFA CALL Wn Call Indirect Subroutine 1 4(2)(2) SFA CALL.L Wn Call Indirect Subroutine (long address) 1 4(2)(2) SFA Read and Read-Modify-Write (e.g., bit operations and logical operations) on non-CPU SFRs incur an additional instruction cycle. Cycle times for Slave core are different for Master core, as shown in 2. For dsPIC33CH128MP508 devices, the divide instructions must be preceded with a “REPEAT #5” instruction, such that they are executed six consecutive times  2017-2019 Microchip Technology Inc. DS70005319D-page 717 dsPIC33CH128MP508 FAMILY TABLE 22-2: INSTRUCTION SET OVERVIEW (CONTINUED) Base Assembly Instr Mnemonic # 19 CLR Assembly Syntax Description # of Words # of Cycles(1) Status Flags Affected None CLR f f = 0x0000 1 1 CLR WREG WREG = 0x0000 1 1 None CLR Ws Ws = 0x0000 1 1 None CLR Acc,Wx,Wxd,Wy,Wyd,AWB Clear Accumulator 1 1 OA,OB,SA,SB Clear Watchdog Timer 1 1 WDTO,Sleep 20 CLRWDT CLRWDT 21 COM COM f f=f 1 1 N,Z COM f,WREG WREG = f 1 1 N,Z COM Ws,Wd Wd = Ws 1 1 N,Z CP f Compare f with WREG 1 1 C,DC,N,OV,Z CP Wb,#lit8 Compare Wb with lit8 1 1 C,DC,N,OV,Z CP Wb,Ws Compare Wb with Ws (Wb – Ws) 1 1 C,DC,N,OV,Z f Compare f with 0x0000 1 1 C,DC,N,OV,Z 22 CP 23 CP0 CP0 CP0 Ws Compare Ws with 0x0000 1 1 C,DC,N,OV,Z 24 CPB CPB f Compare f with WREG, with Borrow 1 1 C,DC,N,OV,Z CPB Wb,#lit8 Compare Wb with lit8, with Borrow 1 1 C,DC,N,OV,Z CPB Wb,Ws Compare Wb with Ws, with Borrow (Wb – Ws – C) 1 1 C,DC,N,OV,Z CPSEQ CPSEQ Wb,Wn Compare Wb with Wn, Skip if = 1 1 (2 or 3) None CPBEQ CPBEQ Wb,Wn,Expr Compare Wb with Wn, Branch if = 1 1 (5) None CPSGT CPSGT Wb,Wn Compare Wb with Wn, Skip if > 1 1 (2 or 3) None 25 26 CPBGT CPBGT Wb,Wn,Expr Compare Wb with Wn, Branch if > 1 1 (5) None 27 CPSLT CPSLT Wb,Wn Compare Wb with Wn, Skip if < 1 1 (2 or 3) None CPBLT Wb,Wn,Expr Compare Wb with Wn, Branch if < 1 1 (5) None 28 CPSNE CPSNE Wb,Wn Compare Wb with Wn, Skip if  1 1 (2 or 3) None CPBNE Wb,Wn,Expr Compare Wb with Wn, Branch if  1 1 (5) None 29 CTXTSWP CTXTSWP #1it3 Switch CPU Register Context to Context Defined by lit3 1 2 None 30 CTXTSWP CTXTSWP Wn Switch CPU Register Context to Context Defined by Wn 1 2 None 31 DAW.B DAW.B Wn Wn = Decimal Adjust Wn 1 1 C 32 DEC DEC f f=f–1 1 1 C,DC,N,OV,Z DEC f,WREG WREG = f – 1 1 1 C,DC,N,OV,Z DEC Ws,Wd Wd = Ws – 1 1 1 C,DC,N,OV,Z DEC2 f f=f–2 1 1 C,DC,N,OV,Z DEC2 f,WREG WREG = f – 2 1 1 C,DC,N,OV,Z DEC2 Ws,Wd Wd = Ws – 2 1 1 C,DC,N,OV,Z 33 DEC2 34 DISI DISI #lit14 Disable Interrupts for k Instruction Cycles 1 1 None 35 DIVF DIVF Wm,Wn Signed 16/16-Bit Fractional Divide 1 18/6 N,Z,C,OV 36 DIV.S DIV.S Wm,Wn Signed 16/16-Bit Integer Divide 1 18/6 N,Z,C,OV DIV.SD Wm,Wn Signed 32/16-Bit Integer Divide 1 18/6 N,Z,C,OV DIV.U Wm,Wn Unsigned 16/16-Bit Integer Divide 1 18/6 N,Z,C,OV DIV.UD Wm,Wn Unsigned 32/16-Bit Integer Divide 1 18/6 N,Z,C,OV 37 DIV.U 38 DIVF2 DIVF2 Wm,Wn Signed 16/16-Bit Fractional Divide (W1:W0 preserved) 1 6 N,Z,C,OV 39 DIV2.S DIV2.S Wm,Wn Signed 16/16-Bit Integer Divide (W1:W0 preserved) 1 6 N,Z,C,OV DIV2.SD Wm,Wn Signed 32/16-Bit Integer Divide (W1:W0 preserved) 1 6 N,Z,C,OV Note 1: 2: 3: Read and Read-Modify-Write (e.g., bit operations and logical operations) on non-CPU SFRs incur an additional instruction cycle. Cycle times for Slave core are different for Master core, as shown in 2. For dsPIC33CH128MP508 devices, the divide instructions must be preceded with a “REPEAT #5” instruction, such that they are executed six consecutive times DS70005319D-page 718  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 22-2: INSTRUCTION SET OVERVIEW (CONTINUED) Base Assembly Instr Mnemonic # 40 41 DIV2.U DO Assembly Syntax Description # of Words # of Cycles(1) Status Flags Affected DIV2.U Wm,Wn Unsigned 16/16-Bit Integer Divide (W1:W0 preserved) 1 6 N,Z,C,OV DIV2.UD Wm,Wn Unsigned 32/16-Bit Integer Divide (W1:W0 preserved) 1 6 N,Z,C,OV DO #lit15,Expr Do Code to PC + Expr, lit15 + 1 Times 2 2 None DO Wn,Expr Do code to PC + Expr, (Wn) + 1 Times 2 2 None 42 ED ED Wm*Wm,Acc,Wx,Wy,Wxd Euclidean Distance (no accumulate) 1 1 OA,OB,OAB, SA,SB,SAB 43 EDAC EDAC Wm*Wm,Acc,Wx,Wy,Wxd Euclidean Distance 1 1 OA,OB,OAB, SA,SB,SAB 44 EXCH EXCH Wns,Wnd Swap Wns with Wnd 1 1 None 46 FBCL FBCL Ws,Wnd Find Bit Change from Left (MSb) Side 1 1 C 47 FF1L FF1L Ws,Wnd Find First One from Left (MSb) Side 1 1 C 48 FF1R FF1R Ws,Wnd Find First One from Right (LSb) Side 1 1 C 49 FLIM FLIM Wb, Ws Force Data (upper and lower) Range Limit without Limit Excess Result 1 1 N,Z,OV FLIM.V Wb, Ws, Wd Force Data (upper and lower) Range Limit with Limit Excess Result 1 1 N,Z,OV GOTO Expr Go to Address 2 4/2(2) None GOTO Wn Go to Indirect 1 4/2(2) None GOTO.L Wn Go to Indirect (long address) 1 4/2(2) None INC f f=f+1 1 1 C,DC,N,OV,Z INC f,WREG WREG = f + 1 1 1 C,DC,N,OV,Z INC Ws,Wd Wd = Ws + 1 1 1 C,DC,N,OV,Z INC2 f f=f+2 1 1 C,DC,N,OV,Z INC2 f,WREG WREG = f + 2 1 1 C,DC,N,OV,Z INC2 Ws,Wd Wd = Ws + 2 1 1 C,DC,N,OV,Z IOR f f = f .IOR. WREG 1 1 N,Z IOR f,WREG WREG = f .IOR. WREG 1 1 N,Z IOR #lit10,Wn Wd = lit10 .IOR. Wd 1 1 N,Z IOR Wb,Ws,Wd Wd = Wb .IOR. Ws 1 1 N,Z IOR Wb,#lit5,Wd Wd = Wb .IOR. lit5 1 1 N,Z Wso,#Slit4,Acc Load Accumulator 1 1 OA,OB,OAB, SA,SB,SAB 50 51 52 53 GOTO INC INC2 IOR 54 LAC LAC LAC.D Wso, #Slit4, Acc Load Accumulator Double 1 2 OA,SA,OB,SB 55 LDSLV LDSLV Wso,Wdo,lit2 Move a Single Instruction Word from Master to Slave PRAM 1 1 None 56 LNK LNK #lit14 Link Frame Pointer 1 1 SFA 57 LSR LSR f f = Logical Right Shift f 1 1 C,N,OV,Z LSR f,WREG WREG = Logical Right Shift f 1 1 C,N,OV,Z LSR Ws,Wd Wd = Logical Right Shift Ws 1 1 C,N,OV,Z LSR Wb,Wns,Wnd Wnd = Logical Right Shift Wb by Wns 1 1 N,Z LSR Wb,#lit5,Wnd Wnd = Logical Right Shift Wb by lit5 1 1 N,Z MAC Wm*Wn,Acc,Wx,Wxd,Wy,Wyd, Multiply and Accumulate AWB 1 1 OA,OB,OAB, SA,SB,SAB MAC Wm*Wm,Acc,Wx,Wxd,Wy,Wyd Square and Accumulate 1 1 OA,OB,OAB, SA,SB,SAB MAX Acc Force Data Maximum Range Limit 1 1 N,OV,Z MAX.V Acc, Wnd Force Data Maximum Range Limit with Result 1 1 N,OV,Z 58 59 Note MAC MAX 1: 2: 3: Read and Read-Modify-Write (e.g., bit operations and logical operations) on non-CPU SFRs incur an additional instruction cycle. Cycle times for Slave core are different for Master core, as shown in 2. For dsPIC33CH128MP508 devices, the divide instructions must be preceded with a “REPEAT #5” instruction, such that they are executed six consecutive times  2017-2019 Microchip Technology Inc. DS70005319D-page 719 dsPIC33CH128MP508 FAMILY TABLE 22-2: INSTRUCTION SET OVERVIEW (CONTINUED) Base Assembly Instr Mnemonic # 60 61 62 MIN MOV MOVPAG Assembly Syntax Description # of Words # of Cycles(1) Status Flags Affected MIN Acc If Accumulator A Less than B Load Accumulator with B or vice versa 1 1 N,OV,Z MIN.V Acc, Wd If Accumulator A Less than B Accumulator Force Minimum Data Range Limit with Limit Excess Result 1 1 N,OV,Z MINZ Acc Accumulator Force Minimum Data Range Limit 1 1 N,OV,Z MINZ.V Acc, Wd Accumulator Force Minimum Data Range Limit with Limit Excess Result 1 1 N,OV,Z MOV f,Wn Move f to Wn 1 1 None MOV f Move f to f 1 1 None MOV f,WREG Move f to WREG 1 1 None MOV #lit16,Wn Move 16-Bit Literal to Wn 1 1 None MOV.b #lit8,Wn Move 8-Bit Literal to Wn 1 1 None MOV Wn,f Move Wn to f 1 1 None MOV Wso,Wdo Move Ws to Wd 1 1 None MOV WREG,f Move WREG to f 1 1 None 1 2 None MOV.D Wns,Wd Move Double from W(ns):W(ns + 1) to Wd MOV.D Ws,Wnd Move Double from Ws to W(nd + 1):W(nd) 1 2 None MOVPAG #lit10,DSRPAG Move 10-Bit Literal to DSRPAG 1 1 None MOVPAG #lit8,TBLPAG Move 8-Bit Literal to TBLPAG 1 1 None MOVPAG Ws, DSRPAG Move Ws[9:0] to DSRPAG 1 1 None MOVPAG Ws, TBLPAG Move Ws[7:0] to TBLPAG 1 1 None 64 MOVSAC MOVSAC Acc,Wx,Wxd,Wy,Wyd,AWB Prefetch and Store Accumulator 1 1 None 65 MPY MPY Wm*Wn,Acc,Wx,Wxd,Wy,Wyd Multiply Wm by Wn to Accumulator 1 1 OA,OB,OAB, SA,SB,SAB MPY Wm*Wm,Acc,Wx,Wxd,Wy,Wyd Square Wm to Accumulator 1 1 OA,OB,OAB, SA,SB,SAB Wm*Wn,Acc,Wx,Wxd,Wy,Wyd 66 MPY.N MPY.N -(Multiply Wm by Wn) to Accumulator 1 1 None 67 MSC MSC Wm*Wm,Acc,Wx,Wxd,Wy,Wyd, AWB Multiply and Subtract from Accumulator 1 1 OA,OB,OAB, SA,SB,SAB 68 MUL MUL.SS Wb,Ws,Wnd {Wnd + 1, Wnd} = Signed(Wb) * Signed(Ws) 1 1 None MUL.SS Wb,Ws,Acc Accumulator = Signed(Wb) * Signed(Ws) 1 1 None MUL.SU Wb,Ws,Wnd {Wnd + 1, Wnd} = Signed(Wb) * Unsigned(Ws) 1 1 None MUL.SU Wb,Ws,Acc Accumulator = Signed(Wb) * Unsigned(Ws) 1 1 None MUL.SU Wb,#lit5,Acc Accumulator = Signed(Wb) * Unsigned(lit5) 1 1 None MUL.US Wb,Ws,Wnd {Wnd + 1, Wnd} = Unsigned(Wb) * Signed(Ws) 1 1 None MUL.US Wb,Ws,Acc Accumulator = Unsigned(Wb) * Signed(Ws) 1 1 None MUL.UU Wb,Ws,Wnd {Wnd + 1, Wnd} = Unsigned(Wb) * Unsigned(Ws) 1 1 None MUL.UU Wb,#lit5,Acc Accumulator = Unsigned(Wb) * Unsigned(lit5) 1 1 None MUL.UU Wb,Ws,Acc Accumulator = Unsigned(Wb) * Unsigned(Ws) 1 1 None MULW.SS Wb,Ws,Wnd Wnd = Signed(Wb) * Signed(Ws) 1 1 None MULW.SU Wb,Ws,Wnd Wnd = Signed(Wb) * Unsigned(Ws) 1 1 None MULW.US Wb,Ws,Wnd Wnd = Unsigned(Wb) * Signed(Ws) 1 1 None MULW.UU Wb,Ws,Wnd Wnd = Unsigned(Wb) * Unsigned(Ws) 1 1 None MUL.SU Wb,#lit5,Wnd {Wnd + 1, Wnd} = Signed(Wb) * Unsigned(lit5) 1 1 None MUL.SU Wb,#lit5,Wnd Wnd = Signed(Wb) * Unsigned(lit5) 1 1 None MUL.UU Wb,#lit5,Wnd {Wnd + 1, Wnd} = Unsigned(Wb) * Unsigned(lit5) 1 1 None MUL.UU Wb,#lit5,Wnd Wnd = Unsigned(Wb) * Unsigned(lit5) 1 1 None MUL f W3:W2 = f * WREG 1 1 None Note 1: 2: 3: Read and Read-Modify-Write (e.g., bit operations and logical operations) on non-CPU SFRs incur an additional instruction cycle. Cycle times for Slave core are different for Master core, as shown in 2. For dsPIC33CH128MP508 devices, the divide instructions must be preceded with a “REPEAT #5” instruction, such that they are executed six consecutive times DS70005319D-page 720  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 22-2: INSTRUCTION SET OVERVIEW (CONTINUED) Base Assembly Instr Mnemonic # 69 70 NEG NEG NOP # of Words # of Cycles(1) Status Flags Affected Negate Accumulator 1 1 OA,OB,OAB, SA,SB,SAB C,DC,N,OV,Z Assembly Syntax Acc Description NEG f f=f+1 1 1 NEG f,WREG WREG = f + 1 1 1 C,DC,N,OV,Z NEG Ws,Wd Wd = Ws + 1 1 1 C,DC,N,OV,Z NOP No Operation 1 1 None NOPR No Operation 1 1 None 71 NORM NORM Acc, Wd Normalize Accumulator 1 1 N,OV,Z 72 POP POP f Pop f from Top-of-Stack (TOS) 1 1 None POP Wdo Pop from Top-of-Stack (TOS) to Wdo 1 1 None POP.D Wnd Pop from Top-of-Stack (TOS) to W(nd):W(nd + 1) 1 2 None Pop Shadow Registers 1 1 All f Push f to Top-of-Stack (TOS) 1 1 None PUSH Wso Push Wso to Top-of-Stack (TOS) 1 1 None PUSH.D Wns Push W(ns):W(ns + 1) to Top-of-Stack (TOS) 1 2 None Push Shadow Registers 1 1 None POP.S 73 PUSH PUSH PUSH.S 74 PWRSAV PWRSAV #lit1 Go into Sleep or Idle mode 1 1 WDTO,Sleep 75 RCALL RCALL Expr Relative Call 1 4/2(2) SFA RCALL Wn Computed Call 1 4/2(2) SFA 1 1 None 76 REPEAT REPEAT #lit15 Repeat Next Instruction lit15 + 1 Times REPEAT Wn Repeat Next Instruction (Wn) + 1 Times 1 1 None 77 RESET RESET Software Device Reset 1 1 None Return from Interrupt 1 6 (5)/3(2) SFA Return with Literal in Wn 1 6 (5)/3(2) SFA Return from Subroutine 1 6 (5)/3(2) SFA f f = Rotate Left through Carry f 1 1 C,N,Z RLC f,WREG WREG = Rotate Left through Carry f 1 1 C,N,Z RLC Ws,Wd Wd = Rotate Left through Carry Ws 1 1 C,N,Z RLNC f f = Rotate Left (No Carry) f 1 1 N,Z RLNC f,WREG WREG = Rotate Left (No Carry) f 1 1 N,Z 78 RETFIE RETFIE 79 RETLW RETLW 80 RETURN RETURN 81 RLC RLC 82 83 84 85 RLNC RRC RRNC SAC #lit10,Wn RLNC Ws,Wd Wd = Rotate Left (No Carry) Ws 1 1 N,Z RRC f f = Rotate Right through Carry f 1 1 C,N,Z RRC f,WREG WREG = Rotate Right through Carry f 1 1 C,N,Z RRC Ws,Wd Wd = Rotate Right through Carry Ws 1 1 C,N,Z RRNC f f = Rotate Right (No Carry) f 1 1 N,Z RRNC f,WREG WREG = Rotate Right (No Carry) f 1 1 N,Z RRNC Ws,Wd Wd = Rotate Right (No Carry) Ws 1 1 N,Z SAC Acc,#Slit4,Wdo Store Accumulator 1 1 None SAC.R Acc,#Slit4,Wdo Store Rounded Accumulator 1 1 None SAC.D #Slit4,Wdo Store Accumulator Double 1 1 None 86 SE SE Ws,Wnd Wnd = Sign-Extended Ws 1 1 C,N,Z 87 SETM SETM f f = 0xFFFF 1 1 None SETM WREG WREG = 0xFFFF 1 1 None SETM Ws Ws = 0xFFFF 1 1 None SFTAC Acc,Wn Arithmetic Shift Accumulator by (Wn) 1 1 OA,OB,OAB, SA,SB,SAB SFTAC Acc,#Slit6 Arithmetic Shift Accumulator by Slit6 1 1 OA,OB,OAB, SA,SB,SAB 88 Note SFTAC 1: 2: 3: Read and Read-Modify-Write (e.g., bit operations and logical operations) on non-CPU SFRs incur an additional instruction cycle. Cycle times for Slave core are different for Master core, as shown in 2. For dsPIC33CH128MP508 devices, the divide instructions must be preceded with a “REPEAT #5” instruction, such that they are executed six consecutive times  2017-2019 Microchip Technology Inc. DS70005319D-page 721 dsPIC33CH128MP508 FAMILY TABLE 22-2: INSTRUCTION SET OVERVIEW (CONTINUED) Base Assembly Instr Mnemonic # 89 91 92 93 94 95 SL SUB SUBB SUBR SUBBR SWAP Assembly Syntax Description # of Words # of Cycles(1) Status Flags Affected SL f f = Left Shift f 1 1 C,N,OV,Z SL f,WREG WREG = Left Shift f 1 1 C,N,OV,Z SL Ws,Wd Wd = Left Shift Ws 1 1 C,N,OV,Z SL Wb,Wns,Wnd Wnd = Left Shift Wb by Wns 1 1 N,Z SL Wb,#lit5,Wnd Wnd = Left Shift Wb by lit5 1 1 N,Z SUB Acc Subtract Accumulators 1 1 OA,OB,OAB, SA,SB,SAB SUB f f = f – WREG 1 1 C,DC,N,OV,Z SUB f,WREG WREG = f – WREG 1 1 C,DC,N,OV,Z SUB #lit10,Wn Wn = Wn – lit10 1 1 C,DC,N,OV,Z SUB Wb,Ws,Wd Wd = Wb – Ws 1 1 C,DC,N,OV,Z SUB Wb,#lit5,Wd Wd = Wb – lit5 1 1 C,DC,N,OV,Z SUBB f f = f – WREG – (C) 1 1 C,DC,N,OV,Z SUBB f,WREG WREG = f – WREG – (C) 1 1 C,DC,N,OV,Z SUBB #lit10,Wn Wn = Wn – lit10 – (C) 1 1 C,DC,N,OV,Z SUBB Wb,Ws,Wd Wd = Wb – Ws – (C) 1 1 C,DC,N,OV,Z SUBB Wb,#lit5,Wd Wd = Wb – lit5 – (C) 1 1 C,DC,N,OV,Z SUBR f f = WREG – f 1 1 C,DC,N,OV,Z SUBR f,WREG WREG = WREG – f 1 1 C,DC,N,OV,Z SUBR Wb,Ws,Wd Wd = Ws – Wb 1 1 C,DC,N,OV,Z SUBR Wb,#lit5,Wd Wd = lit5 – Wb 1 1 C,DC,N,OV,Z SUBBR f f = WREG – f – (C) 1 1 C,DC,N,OV,Z SUBBR f,WREG WREG = WREG – f – (C) 1 1 C,DC,N,OV,Z SUBBR Wb,Ws,Wd Wd = Ws – Wb – (C) 1 1 C,DC,N,OV,Z SUBBR Wb,#lit5,Wd Wd = lit5 – Wb – (C) 1 1 C,DC,N,OV,Z SWAP.b Wn Wn = Nibble Swap Wn 1 1 None SWAP Wn Wn = Byte Swap Wn 1 1 None None 96 TBLRDH TBLRDH Ws,Wd Read Prog[23:16] to Wd[7:0] 1 5/3(2) 97 TBLRDL TBLRDL Ws,Wd Read Prog[15:0] to Wd 1 5/3(2) None 98 TBLWTH TBLWTH Ws,Wd Write Ws[7:0] to Prog[23:16] 1 2 None 99 TBLWTL TBLWTL Ws,Wd Write Ws to Prog[15:0] 1 2 None 101 ULNK ULNK Unlink Frame Pointer 1 1 SFA 103 VFSLV VFSLV Wns,Wnd,lit2 Compare (Master) Ws to (Slave) Wd 1 1 None 104 XOR XOR f f = f .XOR. WREG 1 1 N,Z XOR f,WREG WREG = f .XOR. WREG 1 1 N,Z XOR #lit10,Wn Wd = lit10 .XOR. Wd 1 1 N,Z XOR Wb,Ws,Wd Wd = Wb .XOR. Ws 1 1 N,Z XOR Wb,#lit5,Wd Wd = Wb .XOR. lit5 1 1 N,Z ZE Ws,Wnd Wnd = Zero-Extend Ws 1 1 C,Z,N 105 ZE Note 1: 2: 3: Read and Read-Modify-Write (e.g., bit operations and logical operations) on non-CPU SFRs incur an additional instruction cycle. Cycle times for Slave core are different for Master core, as shown in 2. For dsPIC33CH128MP508 devices, the divide instructions must be preceded with a “REPEAT #5” instruction, such that they are executed six consecutive times DS70005319D-page 722  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 23.0 DEVELOPMENT SUPPORT Move a design from concept to production in record time with Microchip’s award-winning development tools. Microchip tools work together to provide state of the art debugging for any project with easy-to-use Graphical User Interfaces (GUIs) in our free MPLAB® X and Atmel Studio Integrated Development Environments (IDEs), and our code generation tools. Providing the ultimate ease-of-use experience, Microchip’s line of programmers, debuggers and emulators work seamlessly with our software tools. Microchip development boards help evaluate the best silicon device for an application, while our line of third party tools round out our comprehensive development tool solutions. Microchip’s MPLAB X and Atmel Studio ecosystems provide a variety of embedded design tools to consider, which support multiple devices, such as PIC® MCUs, AVR® MCUs, SAM MCUs and dsPIC® DSCs. MPLAB X tools are compatible with Windows®, Linux® and Mac® operating systems while Atmel Studio tools are compatible with Windows. Go to the following website for more information and details: https://www.microchip.com/development-tools/  2017-2019 Microchip Technology Inc. DS70005319D-page 723 dsPIC33CH128MP508 FAMILY NOTES: DS70005319D-page 724  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 24.0 ELECTRICAL CHARACTERISTICS This section provides an overview of the dsPIC33CH128MP508 family electrical characteristics. Additional information will be provided in future revisions of this document as it becomes available. Absolute maximum ratings for the dsPIC33CH128MP508 family are listed below. Exposure to these maximum rating conditions for extended periods may affect device reliability. Functional operation of the device at these, or any other conditions above the parameters indicated in the operation listings of this specification, is not implied. Absolute Maximum Ratings(1) Ambient temperature under bias.............................................................................................................-40°C to +125°C Storage temperature .............................................................................................................................. -65°C to +150°C Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +4.0V Voltage on any pin that is not 5V tolerant with respect to VSS(3)..................................................... -0.3V to (VDD + 0.3V) Voltage on any 5V tolerant pin with respect to VSS when VDD  3.0V(3) ................................................... -0.3V to +5.5V Voltage on any 5V tolerant pin with respect to Vss when VDD < 3.0V(3) ................................................... -0.3V to +3.6V Maximum current out of VSS pin ...........................................................................................................................300 mA Maximum current into VDD pin(2) ...........................................................................................................................300 mA Maximum current sunk/sourced by any 4x I/O pin..................................................................................................15 mA Maximum current sunk/sourced by any 8x I/O pin ..................................................................................................25 mA Maximum current sunk by a group of I/Os between two VSS pins(4).....................................................................200 mA Maximum current sourced by a group of I/Os between two VDD pins(4) ..............................................................200 mA Note 1: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those, or any other conditions above those indicated in the operation listings of this specification, is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. 2: Maximum allowable current is a function of device maximum power dissipation (see Table 24-2). 3: See the “Pin Diagrams” section for the 5V tolerant pins. 4: Not applicable to AVDD and AVSS pins.  2017-2019 Microchip Technology Inc. DS70005319D-page 725 dsPIC33CH128MP508 FAMILY 24.1 DC Characteristics TABLE 24-1: OPERATING MIPS vs. VOLTAGE Characteristic — TABLE 24-2: VDD Range (in Volts) Temperature Range (in °C) 3.0V to 3.6V 3.0V to 3.6V Maximum MIPS dsPIC33CH128MP508 Family Master Slave -40°C to +85°C 90 100 -40°C to +125°C 90 100 THERMAL OPERATING CONDITIONS Rating Symbol Min. Typ. Max. Unit Operating Junction Temperature Range TJ -40 — +125 °C Operating Ambient Temperature Range TA -40 — +85 °C Operating Junction Temperature Range TJ -40 — +140 °C Operating Ambient Temperature Range TA -40 — +125 °C Industrial Temperature Devices Extended Temperature Devices Power Dissipation: Internal Chip Power Dissipation: PINT = VDD x (IDD –  IOH) PD PINT + PI/O W PDMAX (TJ – TA)/JA W I/O Pin Power Dissipation: I/O =  ({VDD – VOH} x IOH) +  (VOL x IOL) Maximum Allowed Power Dissipation TABLE 24-3: THERMAL PACKAGING CHARACTERISTICS Characteristic Symbol Typ. Max. Unit Notes Package Thermal Resistance, 80-Pin TQFP 12x12x1 mm JA 50.67 — °C/W 1 Package Thermal Resistance, 64-Pin TQFP 10x10x1 mm JA 45.7 — °C/W 1 Package Thermal Resistance, 64-Pin QFN 9x9 mm JA 18.7 — °C/W 1 Package Thermal Resistance, 48-Pin TQFP 7x7 mm JA 62.76 — °C/W 1 Package Thermal Resistance, 48-Pin UQFN 6x6 mm JA 27.6 — °C/W 1 Package Thermal Resistance, 36-Pin UQFN 5x5 mm JA 29.2 — °C/W 1 Package Thermal Resistance, 28-Pin UQFN 6x6 mm JA 22.41 — °C/W 1 Package Thermal Resistance, 28-Pin SSOP 5.30 mm JA 52.84 — °C/W 1 Note 1: Junction to ambient thermal resistance, Theta-JA (JA) numbers are achieved by package simulations. DS70005319D-page 726  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 24-4: OPERATING VOLTAGE SPECIFICATIONS Operating Conditions: 3.0V to 3.6V (unless otherwise stated)(1) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Symbol No. Characteristic Min. Typ. Max. Units Conditions Operating Voltage DC10 VDD Supply Voltage 3.0 — 3.6 V DC11 AVDD Supply Voltage Greater of: VDD – 0.3 or 3.0 — Lesser of: VDD + 0.3 or 3.6 V DC16 VPOR VDD Start Voltage to Ensure Internal Power-on Reset Signal — — VSS V DC17 SVDD VDD Rise Rate to Ensure Internal Power-on Reset Signal 1.0 — — V/ms BO10 VBOR BOR Event on VDD Transition High-to-Low(2) 2.68 2.84 2.99 V Note 1: 2: The difference between AVDD supply and VDD supply must not exceed ±300 mV at all times, including during device power-up 0V-3V in 3 ms Device is functional at VBORMIN < VDD < VDDMIN. Analog modules (ADC and comparators) may have degraded performance. Parameters are characterized but not tested.  2017-2019 Microchip Technology Inc. DS70005319D-page 727 dsPIC33CH128MP508 FAMILY TABLE 24-5: DC CHARACTERISTICS: OPERATING CURRENT (IDD) (MASTER RUN/SLAVE RUN) DC CHARACTERISTICS Parameter No. Operating Current (IDD) DC20 DC21 DC22 DC23 DC24 DC25 Note 1: Master (Run) + Slave (Run) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Typ. Max. Units Conditions 11.6 15.7 mA -40°C 11.7 17.5 mA +25°C (1) 11.9 23.5 mA +85°C 15.8 30.0 mA +125°C 15.9 20.3 mA -40°C 16.0 22.2 mA +25°C 16.1 28.0 mA +85°C 20.0 34.3 mA +125°C 23.7 28.9 mA -40°C 23.9 30.9 mA +25°C 25.9 36.6 mA +85°C 27.8 42.1 mA +125°C 37.3 44.0 mA -40°C 37.5 46.1 mA +25°C 37.2 51.1 mA +85°C 41.1 55.7 mA +125°C 45.0 52.4 mA -40°C 45.2 54.8 mA +25°C 44.8 59.1 mA +85°C 48.3 63.1 mA +125°C 45.5 53.0 mA -40°C 45.7 55.3 mA +25°C 45.3 59.6 mA +85°C 48.9 63.6 mA +125°C 3.3V 10 MIPS (N = 1, N2 = 5, N3 = 2, M = 50, FVCO = 400 MHz, FPLLO = 40 MHz) 3.3V 20 MIPS (N = 1, N2 = 5, N3 = 1, M = 60, FVCO = 480 MHz, FPLLO = 280 MHz) 3.3V 40 MIPS (N = 1, N2 = 3, N3 = 1, M = 60, FVCO = 480 MHz, FPLLO = 160 MHz) 3.3V 70 MIPS (N = 1, N2 = 2, N3 = 1, M = 70, FVCO = 560 MHz, FPLLO = 280 MHz) 3.3V 90 MIPS (N = 1, N2 = 2, N3 = 1, M = 90, FVCO = 720 MHz, FPLLO = 360 MHz) 3.3V 100 MIPS (N = 1, N2 = 1, N3 = 1, M = 50, FVCO = 400 MHz, FPLLO = 400 MHz); Slave runs at 100 MIPS but Master is still at 90 MIPS IDD is primarily a function of the operating voltage and frequency. Other factors, such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements are as follows: • FIN = 8 MHz, FPFD = 8 MHz • CLKO is configured as an I/O input pin in the Configuration Word • All I/O pins are configured as output low • MCLR = VDD, WDT and FSCM are disabled • CPU, SRAM, program memory and data memory are operational • No peripheral modules are operating or being clocked (all defined PMDx bits are set) • CPU is executing while(1) statement • JTAG is disabled DS70005319D-page 728  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 24-6: DC CHARACTERISTICS: OPERATING CURRENT (IDD) (MASTER SLEEP/SLAVE RUN) DC CHARACTERISTICS Parameter No. Operating Current (IDD) DC20a DC21a DC22a DC23a DC24a DC25a Note 1: Master (Sleep) + Slave (Run) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Typ. Max. Units Conditions 7.2 11.0 mA -40°C 7.3 12.6 mA +25°C 7.6 18.9 mA +85°C 11.6 25.6 mA +125°C 9.0 12.9 mA -40°C 9.2 14.6 mA +25°C 9.4 20.8 mA +85°C (1) 13.4 27.5 mA +125°C 13.1 17.2 mA -40°C 13.2 19.0 mA +25°C 13.4 25.1 mA +85°C 17.3 31.5 mA +125°C 18.6 23.2 mA -40°C 18.8 25.0 mA +25°C 18.8 31.1 mA +85°C 22.8 37.0 mA +125°C 23.0 28.1 mA -40°C 23.2 30.0 mA +25°C 23.2 35.8 mA +85°C 27.1 41.4 mA +125°C 23.5 28.6 mA -40°C 23.7 30.4 mA +25°C 23.7 36.4 mA +85°C 27.6 41.9 mA +125°C 3.3V 10 MIPS (N = 1, N2 = 5, N3 = 2, M = 50, FVCO = 400 MHz, FPLLO = 40 MHz) 3.3V 20 MIPS (N = 1, N2 = 5, N3 = 1, M = 50, FVCO = 400 MHz, FPLLO = 80 MHz) 3.3V 40 MIPS (N = 1, N2 = 3, N3 = 1, M = 60, FVCO = 480 MHz, FPLLO = 160 MHz) 3.3V 70 MIPS (N = 1, N2 = 2, N3 = 1, M = 70, FVCO = 560 MHz, FPLLO = 280 MHz) 3.3V 90 MIPS (N = 1, N2 = 2, N3 = 1, M = 90, FVCO = 720 MHz, FPLLO = 360 MHz) 3.3V 100 MIPS (N = 1, N2 = 1, N3 = 1, M = 50, FVCO = 400 MHz, FPLLO = 400 MHz) IDD is primarily a function of the operating voltage and frequency. Other factors, such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements are as follows: • Oscillator is switched to EC+PLL mode in software • CLKO is configured as an I/O input pin in the Configuration Word • All I/O pins are configured as output low • MCLR = VDD, WDT and FSCM are disabled • CPU, SRAM, program memory and data memory are operational • No peripheral modules are operating or being clocked (all defined PMDx bits are set) • CPU is executing while(1) statement • JTAG is disabled  2017-2019 Microchip Technology Inc. DS70005319D-page 729 dsPIC33CH128MP508 FAMILY TABLE 24-7: DC CHARACTERISTICS: OPERATING CURRENT (IDD) (MASTER RUN/SLAVE SLEEP) DC CHARACTERISTICS Parameter No. Operating Current (IDD) DC20b DC21b DC22b DC23b DC24b Note 1: Master (Run) + Slave (Sleep) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Typ. Max. Units Conditions 7.9 11.8 mA -40°C 8.0 13.4 mA +25°C 8.2 19.5 mA +85°C 12.2 26.3 mA +125°C 10.3 14.4 mA -40°C 10.5 16.0 mA +25°C 10.6 22.1 mA +85°C 14.6 28.7 mA +125°C 14.2 18.5 mA -40°C 14.4 20.3 mA +25°C 14.5 26.3 mA +85°C (1) 18.4 32.6 mA +125°C 22.3 27.4 mA -40°C 22.5 29.4 mA +25°C 22.4 34.9 mA +85°C 26.4 40.7 mA +125°C 25.6 31.0 mA -40°C 25.8 33.1 mA +25°C 25.7 38.2 mA +85°C 29.4 43.8 mA +125°C 3.3V 10 MIPS (N = 1, N2 = 5, N3 = 2, M = 50, FVCO = 400 MHz, FPLLO = 40 MHz) 3.3V 20 MIPS (N = 1, N2 = 5, N3 = 1, M = 50, FVCO = 400 MHz, FPLLO = 80 MHz) 3.3V 40 MIPS (N = 1, N2 = 3, N3 = 1, M = 60, FVCO = 480 MHz, FPLLO = 160 MHz) 3.3V 70 MIPS (N = 1, N2 = 2, N3 = 1, M = 70, FVCO = 560 MHz, FPLLO = 280 MHz) 3.3V 90 MIPS (N = 1, N2 = 2, N3 = 1, M = 90, FVCO = 720 MHz, FPLLO = 360 MHz) IDD is primarily a function of the operating voltage and frequency. Other factors, such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements are as follows: • FIN = 8 MHz, FPFD = 8 MHz • CLKO is configured as an I/O input pin in the Configuration Word • All I/O pins are configured as output low • MCLR = VDD, WDT and FSCM are disabled • CPU, SRAM, program memory and data memory are operational • No peripheral modules are operating or being clocked (all defined PMDx bits are set) • CPU is executing while(1) statement • JTAG is disabled DS70005319D-page 730  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 24-8: DC CHARACTERISTICS: OPERATING CURRENT (IIDLE) (MASTER IDLE/SLAVE IDLE) DC CHARACTERISTICS Parameter No. Operating Current (IDD) DC40 DC41 DC42 DC43 DC44 DC45 Note 1: Master (Idle) + Slave (Idle) Typ. Max. Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Units Conditions (1) 9.1 11.1 mA -40°C 9.3 14.8 mA +25°C 9.4 20.7 mA +85°C 13.4 27.5 mA +125°C 10.5 12.5 mA -40°C 10.6 16.3 mA +25°C 10.8 22.2 mA +85°C 14.7 28.8 mA +125°C 14.0 16.3 mA -40°C 14.2 20.1 mA +25°C 14.3 26.0 mA +85°C 18.2 32.3 mA +125°C 18.9 21.6 mA -40°C 19.1 25.5 mA +25°C 19.1 31.2 mA +85°C 23.0 37.2 mA +125°C 23.1 26.1 mA -40°C 23.2 30.0 mA +25°C 23.2 34.8 mA +85°C 27.1 41.4 mA +125°C 22.3 25.2 mA -40°C 22.4 29.2 mA +25°C 22.4 38.7 mA +85°C 26.3 40.6 mA +125°C 3.3V 10 MIPS (N = 1, N2 = 5, N3 = 2, M = 50, FVCO = 400 MHz, FPLLO = 40 MHz) 3.3V 20 MIPS (N = 1, N2 = 5, N3 = 1, M = 50, FVCO = 400 MHz, FPLLO = 80 MHz) 3.3V 40 MIPS (N = 1, N2 = 3, N3 = 1, M = 60, FVCO = 480 MHz, FPLLO = 160 MHz) 3.3V 70 MIPS (N = 1, N2 = 2, N3 = 1, M = 70, FVCO = 560 MHz, FPLLO = 280 MHz) 3.3V 90 MIPS (N = 1, N2 = 2, N3 = 1, M = 90, FVCO = 720 MHz, FPLLO = 360 MHz) 3.3V 100 MIPS (N = 1, N2 = 1, N3 = 1, M = 50, FVCO = 400 MHz, FPLLO = 400 MHz); Slave Idle at 100 MIPS but Master Idle at 90 MIPS IDD is primarily a function of the operating voltage and frequency. Other factors, such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements are as follows: • FIN = 8 MHz, FPFD = 8 MHz • CLKO is configured as an I/O input pin in the Configuration Word • All I/O pins are configured as output low • MCLR = VDD, WDT and FSCM are disabled • CPU, SRAM, program memory and data memory are operational • No peripheral modules are operating or being clocked (all defined PMDx bits are set) • CPU is executing while(1) statement • JTAG is disabled  2017-2019 Microchip Technology Inc. DS70005319D-page 731 dsPIC33CH128MP508 FAMILY TABLE 24-9: DC CHARACTERISTICS: IDLE CURRENT (IIDLE) (MASTER IDLE/SLAVE SLEEP) DC CHARACTERISTICS Parameter No. Idle Current (IIDLE) Typ. Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Max. Units Conditions 6.6 8.4 mA -40°C 6.7 11.9 mA +25°C 6.9 17.9 mA +85°C 10.9 24.9 mA +125°C 7.3 9.2 mA -40°C 7.5 12.7 mA +25°C 7.7 18.7 mA +85°C 11.7 25.7 mA +125°C 9.2 11.1 mA -40°C 9.4 14.8 mA +25°C 9.5 20.7 mA +85°C 13.5 27.5 mA +125°C (1) DC40a DC41a DC42a DC43a DC44a Note 1: Master (Idle) + Slave (Sleep) 11.8 13.9 mA -40°C 12.0 17.6 mA +25°C 12.1 23.5 mA +85°C 16.1 30.1 mA +125°C 14.1 16.3 mA -40°C 14.2 20 mA +25°C 14.3 25.9 mA +85°C 18.2 32.3 mA +125°C 3.3V 10 MIPS (N = 1, N2 = 5, N3 = 2, M = 50, FVCO = 400 MHz, FPLLO = 40 MHz) 3.3V 20 MIPS (N = 1, N2 = 5, N3 = 1, M = 50, FVCO = 400 MHz, FPLLO = 80 MHz) 3.3V 40 MIPS (N = 1, N2 = 3, N3 = 1, M = 60, FVCO = 480 MHz, FPLLO = 160 MHz) 3.3V 70 MIPS (N = 1, N2 = 2, N3 = 1, M = 70, FVCO = 560 MHz, FPLLO = 280 MHz) 3.3V 90 MIPS (N = 1, N2 = 2, N3 = 1, M = 90, FVCO = 720 MHz, FPLLO = 360 MHz) Base Idle current (IIDLE) is measured as follows: • FIN = 8 MHz, FPFD = 8 MHz • CLKO is configured as an I/O input pin in the Configuration Word • All I/O pins are configured as output low • MCLR = VDD, WDT and FSCM are disabled • No peripheral modules are operating or being clocked (all defined PMDx bits are set) • The NVMSIDL bit (NVMCON[12]) = 1 (i.e., Flash regulator is set to standby while the device is in Idle mode) • JTAG is disabled DS70005319D-page 732  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 24-10: DC CHARACTERISTICS: IDLE CURRENT (IIDLE) (MASTER SLEEP/SLAVE IDLE) DC CHARACTERISTICS Parameter No. Idle Current (IIDLE) DC40b DC41b DC42b DC43b DC44b DC45b Note 1: Master (Sleep) + Slave (Idle) Typ. Max. Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Units Conditions (1) 6.0 7.8 mA -40°C 6.2 11.4 mA +25°C 6.4 17.5 mA +85°C 10.4 24.4 mA +125°C 6.6 8.4 mA -40°C 6.8 12.0 mA +25°C 7.0 18.1 mA +85°C 11.0 25.0 mA +125°C 8.3 10.1 mA -40°C 8.5 13.8 mA +25°C 8.7 19.9 mA +85°C 12.6 26.7 mA +125°C 10.6 12.6 mA -40°C 10.8 16.3 mA +25°C 10.9 22.3 mA +85°C 14.9 29.0 mA +125°C 12.6 14.7 mA -40°C 12.7 18.4 mA +25°C 12.9 23.6 mA +85°C 16.8 30.9 mA +125°C 11.7 13.8 mA -40°C 11.9 17.6 mA +25°C 12.1 24.4 mA +85°C 16.0 30.1 mA +125°C 3.3V 10 MIPS (N = 1, N2 = 5, N3 = 2, M = 50, FVCO = 400 MHz, FPLLO = 40 MHz) 3.3V 20 MIPS (N = 1, N2 = 5, N3 = 1, M = 50, FVCO = 400 MHz, FPLLO = 80 MHz) 3.3V 40 MIPS (N = 1, N2 = 3, N3 = 1, M = 60, FVCO = 480 MHz, FPLLO = 160 MHz) 3.3V 70 MIPS (N = 1, N2 = 2, N3 = 1, M = 70, FVCO = 560 MHz, FPLLO = 280 MHz) 3.3V 90 MIPS (N = 1, N2 = 2, N3 = 1, M = 90, FVCO = 720 MHz, FPLLO = 360 MHz) 3.3V 100 MIPS (N = 1, N2 = 1, N3 = 1, M = 50, FVCO = 400 MHz, FPLLO = 400 MHz) Base Idle current (IIDLE) is measured as follows: • FIN = 8 MHz, FPFD = 8 MHz • CLKO is configured as an I/O input pin in the Configuration Word • All I/O pins are configured as output low • MCLR = VDD, WDT and FSCM are disabled • No peripheral modules are operating or being clocked (all defined PMDx bits are set) • The NVMSIDL bit (NVMCON[12]) = 1 (i.e., Flash regulator is set to standby while the device is in Idle mode) • JTAG is disabled  2017-2019 Microchip Technology Inc. DS70005319D-page 733 dsPIC33CH128MP508 FAMILY TABLE 24-11: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD) Master Sleep + Slave Sleep DC CHARACTERISTICS Parameter No. Power-Down Current (IPD) Typ. Max. Units Conditions 3.2 4.8 mA -40°C 3.4 8.2 mA +25°C 3.7 14.3 mA +85°C 7.6 21.5 mA +125°C (1) DC60 Note 1: Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended 3.3V IPD (Sleep) current is measured as follows: • CPU core is off, oscillator is configured in EC mode and External Clock is active; OSCI is driven with external square wave from rail-to-rail (EC clock overshoot/undershoot < 250 mV required) • CLKO is configured as an I/O input pin in the Configuration Word • All I/O pins are configured as output low • MCLR = VDD, WDT and FSCM are disabled • All peripheral modules are disabled (PMDx bits are all set) • The VREGS bit (RCON[8]) = 0 (i.e., core regulator is set to standby while the device is in Sleep mode) • JTAG is disabled TABLE 24-12: DC CHARACTERISTICS: WATCHDOG TIMER DELTA CURRENT (IWDT)(1) DC CHARACTERISTICS Parameter No. Master and Slave Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Typ. Max. Units DC61d 2.9 — µA -40°C DC61a 2.7 — µA +25°C DC61b 3.9 — µA +85°C DC61c 5.5 — µA +125°C Note 1: Conditions 3.3V The IWDT current is the additional current consumed when the module is enabled. This current should be added to the base IPD current. All parameters are characterized but not tested during manufacturing. DS70005319D-page 734  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 24-13: DC CHARACTERISTICS: PWM DELTA CURRENT(1,2,3) DC CHARACTERISTICS Parameter No. DC100 DC101 DC102 DC103 Note 1: 2: 3: Master and Slave Typ. Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Max. Units Conditions 6 8 mA 6 6.7 mA -40°C, 3.3V PWM Output 500 kHz, +25°C, 3.3V PWM Input (AFPLLO = 500 MHz), +125°C, 3.3V AVCO = 1000 MHz, PLLFBD = 125, APLLDIV = 2 6.3 8 mA 4.9 6 mA 4.9 5.5 mA 4.9 5.6 mA 2.6 3.4 mA 2.7 3 mA 2.7 3.2 mA 1.5 2.9 mA 1.5 2.1 mA 1.5 2.2 mA -40°C, 3.3V PWM Output 500 kHz, +25°C, 3.3V PWM Input (AFPLLO = 400 MHz), +125°C, 3.3V AVCO = 400 MHz, PLLFBD = 50, APLLDIV = 1 -40°C, 3.3V PWM Output 500 kHz, +25°C, 3.3V PWM Input (AFPLLO = 200 MHz), +125°C, 3.3V AVCO = 400 MHz, PLLFBD = 50, APLLDIV = 2 -40°C, 3.3V PWM Output 500 kHz, +25°C, 3.3V PWM Input (AFPLLO = 100 MHz), +125°C, 3.3V AVCO = 400 MHz, PLLFBD = 50, APLLDIV = 4 The APLL current is not included. The APLL current will be the same if more than one PWM or all eight PWMs are running. Delta current is for the one instance of PWM running. PWM is configured for Low-Resolution mode with HREN (PGxCONL[7]) = 0. All parameters are characterized but not tested during manufacturing. TABLE 24-14: DC CHARACTERISTICS: APLL DELTA CURRENT DC CHARACTERISTICS Parameter No. DC110 DC111 DC112 DC113 Note 1: 2: Master or Slave(2) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Conditions(1) Typ. Max. Units — 9.4 mA -40°C.,3.3V 7.2 9.4 mA +25°C,3.3V — 18 mA +125°C,3.3V — 5.7 mA -40°C.,3.3V 5 5.8 mA +25°C,3.3V — 14 mA +125°C,3.3V — 4.7 mA -40°C.,3.3V 2.9 4.7 mA +25°C,3.3V — 14 mA +125°C,3.3V — 4 mA -40°C.,3.3V 2.3 4 mA +25°C,3.3V — 12 mA +125°C,3.3V AFPLLO @ 500 MHz, AVCO = 1000 MHz, PLLFBD = 125, APLLDIV = 2 AFPLLO @ 400 MHz, AVCO = 400 MHz, PLLFBD = 50, APLLDIV = 1 AFPLLO @ 200 MHz, AVCO = 400 MHz, PLLFBD = 50, APLLDIV = 2 AFPLLO @ 100 MHz, AVCO = 400 MHz, PLLFBD = 50, APLLDIV = 4 The APLL current will be the same if more than one PWM or DAC is run to the APLL clock. All parameters are characterized but not tested during manufacturing. Current is for the APLL for the Master or Slave, not the combined current.  2017-2019 Microchip Technology Inc. DS70005319D-page 735 dsPIC33CH128MP508 FAMILY TABLE 24-15: DC CHARACTERISTICS: ADC  CURRENT DC CHARACTERISTICS Parameter No. DC120 Note 1: 2: Master (1) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended (2) Slave Typ. Max. Typ. Max. — 6.5 Units — 14 mA Conditions -40°C 3.3V 5.5 6 9 14 mA +25°C 3.3V — 7.1 — 15 mA +125°C 3.3V Master shared core continuous conversion; TAD = 14.3 nS (3.5 Msps Conversion rate). Slave dedicated core continuous conversion on all 3 SAR cores; TAD = 14.3 nS (3.5 Msps conversion rate). All parameters are characterized but not tested during manufacturing. TABLE 24-16: DC CHARACTERISTICS: COMPARATOR + DAC DELTA CURRENT DC CHARACTERISTICS Parameter No. DC130 Note 1: Master or Slave Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Typ. Max. Units Conditions — 2.8 mA -40°C, 3.3V AFPLLO @ 500 MHz(1) 1.8 2.6 mA +25°C, 3.3V AFPLLO @ 500 MHz(1) — 3 mA +125°C, 3.3V AFPLLO @ 500 MHz(1) The APLL current is not included. All parameters are characterized but not tested during manufacturing. TABLE 24-17: DC CHARACTERISTICS: PGA DELTA CURRENT(1) DC CHARACTERISTICS Parameter No. DC141 Note 1: Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Slave Typ. Max. Units Conditions — 0.5 mA 0.4 0.65 mA +25°C, 3.3V — 1.1 mA +125°C, 3.3V -40°C, 3.3V All parameters are characterized but not tested during manufacturing. DS70005319D-page 736  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 24-18: I/O PIN INPUT SPECIFICATIONS Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Symbol No. VIL Characteristic Min. Typ.(1) Max. Units Conditions Input Low Voltage DI10 Any I/O Pin and MCLR VSS — 0.2 VDD V DI18 I/O Pins with SDAx, SCLx VSS — 0.3 VDD V SMBus disabled I/O Pins with SDAx, SCLx VSS — 0.8 V SMBus enabled I/O Pins Not 5V Tolerant(3) 0.8 VDD — VDD V 5V Tolerant I/O Pins and MCLR(3) 0.8 VDD — 5.5 V DI19 VIH DI20 Input High Voltage 5V Tolerant I/O Pins with SDAx, SCLx(3) 0.8 VDD — 5.5 V SMBus disabled 5V Tolerant I/O Pins with SDAx, SCLx(3) 2.1 — 5.5 V SMBus enabled I/O Pins with SDAx, SCLx Not 5V Tolerant(3) 0.8 VDD — VDD V SMBus disabled I/O Pins with SDAx, SCLx Not 5V Tolerant(3) 2.1 — VDD V SMBus enabled DI30 ICNPU Input Change Notification Pull-up Current(2,4) 175 360 545 µA VDD = 3.6V, VPIN = VSS DI31 ICNPD Input Change Notification Pull-Down Current(4) 65 215 360 µA VDD = 3.6V, VPIN = VDD Note 1: 2: 3: 4: Data in “Typ.” column are at 3.3V, +25°C unless otherwise stated. Negative current is defined as current sourced by the pin. See the “Pin Diagrams” section for the 5V tolerant I/O pins. All parameters are characterized but not tested during manufacturing. TABLE 24-19: I/O PIN INPUT SPECIFICATIONS Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Symbol No. DI50 IIL Characteristic Max. Units -800 +800 nA Conditions Input Leakage Current(1) I/O Pins 5V Tolerant(2) I/O Pins Not 5V Tolerant Note 1: 2: Min. (2) -800 +800 nA MCLR -800 +800 nA OSCI -800 +800 nA VPIN = VSS or VDD XT and HS modes Negative current is defined as current sourced by the pin. See the “Pin Diagrams” section for the 5V tolerant I/O pins. All parameters are characterized but not tested during manufacturing.  2017-2019 Microchip Technology Inc. DS70005319D-page 737 dsPIC33CH128MP508 FAMILY TABLE 24-20: I/O PIN INPUT INJECTION CURRENT SPECIFICATIONS Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Symbol No. DI60a IICL Characteristic Input Low Injection Current DI60b IICH Input High Injection Current DI60c IICT Total Input Injection Current (sum of all I/O and control pins)(5) Note 1: 2: 3: 4: 5: Min. Max. Units 0 -5(1,4) mA All pins mA All pins, excepting all 5V tolerant pins and SOSCI mA Absolute instantaneous sum of all ± input injection currents from all I/O pins ( | IICL | + | IICH | )  IICT 0 -20 (2,3,4) +5 +20 Conditions VIL Source < (VSS – 0.3). VIH Source > (VDD + 0.3) for non-5V tolerant pins only. 5V tolerant pins do not have an internal high-side diode to VDD, and therefore, cannot tolerate any “positive” input injection current. Injection currents can affect the ADC results. Any number and/or combination of I/O pins, not excluded under IICL or IICH conditions, are permitted in the sum. TABLE 24-21: I/O PIN OUTPUT SPECIFICATIONS Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param. Symbol DO10 DO20 Note 1: VOL VOH Characteristic Min. Typ. Max. Units Conditions Output Low Voltage 4x Sink Driver Pins — — 0.42 V VDD = 3.6V, IOL < 9 mA Output Low Voltage 8x Sink Driver Pins(1) — — 0.4 V VDD = 3.6V, IOL < 11 mA Output High Voltage 4x Source Driver Pins 2.4 — — V VDD = 3.6V, IOH > -8 mA Output High Voltage 8x Source Driver Pins(1) 2.4 — — V VDD = 3.6V, IOH > -12 mA The 8x sink/source pins are RB1, RC8, RC9 and RD8 pins; all other ports are 4x sink drivers. DS70005319D-page 738  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 24-22: ELECTRICAL CHARACTERISTICS: BOR Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)(1) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended DC CHARACTERISTICS Param No. Symbol Characteristic Min.(2) Typ. Max. Units BOR Event on VDD Transition High-to-Low 2.68 2.96 2.99 V Conditions VDD (Note 2) BO10 VBOR Note 1: Device is functional at VBORMIN < VDD < VDDMIN, but will have degraded performance. Device functionality is tested, but not characterized. Analog modules (ADC, PGAs and comparators) may have degraded performance. Parameters are for design guidance only and are not tested in manufacturing. 2: TABLE 24-23: PROGRAM MEMORY Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Symbol No. Characteristic Min. Max. Units Conditions Program Flash Memory D130 EP Cell Endurance 10,000 — D131 VPR VDD for Read 3.0 3.6 D132b VPEW VDD for Self-Timed Write 3.0 3.6 D134 TRETD Characteristic Retention 20 — E/W -40C to +125C V V Year Provided no other specifications are violated, -40C to +125C D137a TPE Page Erase Time 15.3 16.82 ms TPE = 128,454 FRC cycles (Note 1) D138a TWW Word Write Time 47.7 52.3 µs TWW = 400 FRC cycles (Note 1) D139a TRW Row Write Time 2.0 2.2 ms TRW = 16,782 FRC cycles (Note 1) Note 1: Other conditions: FRC = 8 MHz, TUN[5:0] = 011111 (for Minimum), TUN[5:0] = 100000 (for Maximum). This parameter depends on the FRC accuracy (see Table 24-29) and the value of the FRC Oscillator Tuning register (see Register 6-4). For complete details on calculating the Minimum and Maximum time, see Section 3.3.1 “Flash Programming Operations”.  2017-2019 Microchip Technology Inc. DS70005319D-page 739 dsPIC33CH128MP508 FAMILY 24.2 AC Characteristics and Timing Parameters This section defines the dsPIC33CH128MP508 family AC characteristics and timing parameters. TABLE 24-24: TEMPERATURE AND VOLTAGE SPECIFICATIONS – AC Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Operating voltage VDD range as described in Section 24.1 “DC Characteristics”. AC CHARACTERISTICS FIGURE 24-1: LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS Load Condition 1 – for all pins except OSCO Load Condition 2 – for OSCO VDD/2 CL Pin RL VSS CL Pin RL = 464 CL = 50 pF for all pins except OSCO 15 pF for OSCO output VSS TABLE 24-25: CAPACITIVE LOADING REQUIREMENTS ON OUTPUT PINS Param Symbol No. Characteristic Min. Typ. Max. Units Conditions 15 pF In XT and HS modes, when External Clock is used to drive OSCI DO50 COSCO OSCO Pin — — DO56 CIO All I/O Pins and OSCO — — 50 pF EC mode DO58 CB SCLx, SDAx — — 400 pF In I2C mode FIGURE 24-2: EXTERNAL CLOCK TIMING Q1 Q2 Q3 Q4 Q1 Q2 OS30 OS30 Q3 Q4 OSCI OS20 OS25 OS31 OS31 CLKO OS41 DS70005319D-page 740 OS40  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 24-26: EXTERNAL CLOCK TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended AC CHARACTERISTICS Param No. Sym OS10 FIN Min. Typ.(1) Max. Units External CLKI Frequency (External Clocks allowed only in EC and ECPLL modes) DC — 64 MHz EC Oscillator Crystal Frequency 3.5 — 10 MHz XT 10 — 32 MHz HS 15.6 — DC ns Characteristic OS20 TOSC TOSC = 1/FOSC OS25 TCY Instruction Cycle Time(2) OS30 TosL, External Clock in (OSCI) TosH High or Low Time OS31 TosR , TosF OS40 TckR Conditions 10 — DC ns 0.45 x TOSC — 0.55 x TOSC ns EC External Clock in (OSCI) Rise or Fall Time — — 20 ns EC CLKO Rise Time(3,4) — 5.4 — ns (3,4) OS41 TckF CLKO Fall Time — 6.4 — ns OS42 GM External Oscillator Transconductance(3) 2.7 — 4 mA/V XTCFG[1:0] = 00, XTBST = 0 4 — 7 mA/V XTCFG[1:0] = 00, XTBST = 1 4.5 — 7 mA/V XTCFG[1:0] = 01, XTBST = 0 6 — 11.9 mA/V XTCFG[1:0] = 01, XTBST = 1 5.9 — 9.7 mA/V XTCFG[1:0] = 10, XTBST = 0 6.9 — 15.9 mA/V XTCFG[1:0] = 10, XTBST = 1 6.7 — 12 mA/V XTCFG[1:0] = 11, XTBST = 0 7.5 — 19 mA/V XTCFG[1:0] = 11, XTBST = 1 Note 1: 2: 3: 4: Data in “Typ.” column are at 3.3V, +25°C unless otherwise stated. Instruction cycle period (TCY) equals two times the input oscillator time base period. All specified values are based on characterization data for that particular oscillator type, under standard operating conditions, with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at “Minimum” values with an External Clock applied to the OSCI pin. When an External Clock input is used, the “Maximum” cycle time limit is “DC” (no clock) for all devices. Measurements are taken in EC mode. The CLKO signal is measured on the OSCO pin. This parameter is characterized but not tested in manufacturing.  2017-2019 Microchip Technology Inc. DS70005319D-page 741 dsPIC33CH128MP508 FAMILY TABLE 24-27: PLL CLOCK TIMING SPECIFICATIONS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended AC CHARACTERISTICS Param No. Symbol Characteristic Min. Typ.(1) Max. Units OS50 FPLLI PLL Voltage Controlled Oscillator (VCO) Input Frequency Range 8(2) — 64 MHz OS51 FVCO On-Chip VCO System Frequency 400 — 1600 MHz OS52 TLOCK PLL Start-up Time (Lock Time) — 60 — µs Note 1: 2: Conditions ECPLL, XTPLL modes Data in “Typ.” column are at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only and are not tested. Inclusive of FRC Tolerance Specification F20a. TABLE 24-28: AUXILIARY PLL CLOCK TIMING SPECIFICATIONS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended AC CHARACTERISTICS Param No. Symbol Characteristic Min. Typ.(1) Max. Units — 64 MHz OS50 FPLLI APLL Voltage Controlled Oscillator (VCO) Input Frequency Range 8(2) OS51 FVCO On-Chip VCO System Frequency 400 — 1600 MHz OS52 TLOCK APLL Start-up Time (Lock Time) — 60 — µs Note 1: 2: Conditions ECPLL, XTPLL modes Data in “Typ” column are at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only and are not tested in manufacturing. Inclusive of FRC Tolerance Specification F20a. DS70005319D-page 742  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 24-29: INTERNAL FRC ACCURACY AC CHARACTERISTICS Param No. Characteristic Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Min. Typ. Max. Units — +3 % Conditions Internal FRC Accuracy @ FRC Frequency = 8 MHz(1) FRC -1.5 — +1.5 % 0°C  TA +85°C F20b FRC -2 — +2 % +85°C  TA  +125°C F22 BFRC -17 — +17 % -40°C  TA  +125°C Note 1: -3 -40°C  TA 0°C F20a Frequency is calibrated at +25°C and 3.3V. TUNx bits can be used to compensate for temperature drift. TABLE 24-30: INTERNAL LPRC ACCURACY AC CHARACTERISTICS Param No. Characteristic Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Min. Typ. Max. Units Conditions -30 — +30 % -40°C  TA  -10°C VDD = 3.0-3.6V -20 — +20 % -10°C  TA  +85°C VDD = 3.0-3.6V -30 — +30 % +85°C  TA  +125°C VDD = 3.0-3.6V LPRC @ 32 kHz F21a F21b LPRC LPRC  2017-2019 Microchip Technology Inc. DS70005319D-page 743 dsPIC33CH128MP508 FAMILY FIGURE 24-3: I/O TIMING CHARACTERISTICS I/O Pin (Input) DI35 DI40 I/O Pin (Output) New Value Old Value DO31 DO32 Note: Refer to Figure 24-1 for load conditions. TABLE 24-31: I/O TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended AC CHARACTERISTICS Param No. DO31 Symbol TIOR Characteristic Port Output Rise Time(2) Time(2) Min. Typ.(1) Max. Units — 6.5 9.7 ns DO32 TIOF Port Output Fall — 3.2 4.2 ns DI35 TINP INTx Pin High or Low Time (input) 20 — — ns TRBP CNx High or Low Time (input) 2 — — TCY DI40 Note 1: 2: Conditions Data in “Typ.” column are at 3.3V, +25°C unless otherwise stated. This parameter is characterized but not tested in manufacturing. FIGURE 24-4: BOR AND MASTER CLEAR RESET TIMING CHARACTERISTICS MCLR TMCLR (SY20) BOR TBOR (SY30) Various Delays (depending on configuration) Reset Sequence CPU Starts Fetching Code DS70005319D-page 744  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 24-32: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER TIMING REQUIREMENTS AC CHARACTERISTICS Param No. Symbol Characteristic(1) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Min. Typ.(2) Max. Units Conditions SY00 TPU Power-up Period — 200 — µs SY10 TOST Oscillator Start-up Time — 1024 TOSC — — SY13 TIOZ I/O High-Impedance from MCLR Low or Watchdog Timer Reset — 1.5 — µs SY20 TMCLR MCLR Pulse Width (low) 2 — — µs SY30 TBOR BOR Pulse Width (low) 1 — — µs SY35 TFSCM Fail-Safe Clock Monitor Delay — 500 900 µs -40°C to +85°C SY36 TVREG Voltage Regulator Standby-to-Active mode Transition Time — — 40 µs Clock fail to BFRC switch SY37 TOSCDFRC FRC Oscillator Start-up Delay — — 15 µs From POR event SY38 TOSCDLPRC LPRC Oscillator Start-up Delay — — 50 µs From Reset event Note 1: 2: TOSC = OSCI period These parameters are characterized but not tested in manufacturing. Data in “Typ.” column are at 3.3V, +25°C unless otherwise stated.  2017-2019 Microchip Technology Inc. DS70005319D-page 745 dsPIC33CH128MP508 FAMILY FIGURE 24-5: HIGH-SPEED PWMx MODULE FAULT TIMING CHARACTERISTICS MP30 Fault Input (active-low) MP20 PWMx FIGURE 24-6: HIGH-SPEED PWMx MODULE TIMING CHARACTERISTICS MP11 MP10 PWMx Note: Refer to Figure 24-1 for load conditions. TABLE 24-33: HIGH-SPEED PWMx MODULE TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended AC CHARACTERISTICS Param No. Characteristic(1) Symbol Min. Typ. Max. Units 500 MHz — ns Conditions MP00 FIN PWM Input Frequency — MP10 TFPWM PWMx Output Fall Time — — MP11 TRPWM PWMx Output Rise Time — — — ns See Parameter DO31 MP20 TFD Fault Input  to PWMx I/O Change — — 26 ns PCI Inputs 19 through 22 MP30 TFH Fault Input Pulse Width 8 — — ns Note 1: 2: (Note 2) See Parameter DO32 These parameters are characterized but not tested in manufacturing. Input frequency of 500 MHz must be used for High-Resolution mode. DS70005319D-page 746  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 24-34: SPIx MAXIMUM DATA/CLOCK RATE SUMMARY SPI Master Transmit Only (Half-Duplex) SPI Master Transmit/Receive (Full-Duplex) SPI Slave Transmit/Receive (Full-Duplex) CKE Figure 24-7 Table 24-35 — — 0 Figure 24-8 Table 24-35 — — Figure 24-9 Table 24-36 — Figure 24-10 Table 24-37 — — Figure 24-12 Table 24-39 — Figure 24-13 Table 24-38 — — FIGURE 24-7: — Maximum Data Rate (MHz) 15 1 — 0 1 0 1 Condition Using PPS 40 Dedicated Pin 15 Using PPS 40 Dedicated Pin 9 Using PPS 40 Dedicated Pin 9 Using PPS 40 Dedicated Pin 15 Using PPS 40 Dedicated Pin 15 Using PPS 40 Dedicated Pin SPIx MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY, CKE = 0) TIMING CHARACTERISTICS SCKx (CKP = 0) SP10 SP21 SP20 SP20 SP21 SCKx (CKP = 1) SP35 MSb SDOx SP30, SP31 Bit 14 - - - - - -1 LSb SP30, SP31 Note: Refer to Figure 24-1 for load conditions.  2017-2019 Microchip Technology Inc. DS70005319D-page 747 dsPIC33CH128MP508 FAMILY FIGURE 24-8: SPIx MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY, CKE = 1) TIMING CHARACTERISTICS SP36 SCKx (CKP = 0) SP10 SP21 SP20 SP20 SP21 SCKx (CKP = 1) SP35 MSb SDOx Bit 14 - - - - - -1 LSb SP30, SP31 Note: Refer to Figure 24-1 for load conditions. TABLE 24-35: SPIx MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY) TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended AC CHARACTERISTICS Param No. Characteristic(1) Symbol Min. Typ.(2) Max. Units — — 15 MHz Using PPS pins SPI2 dedicated pins Conditions SP10 FscP Maximum SCKx Frequency — — 40 MHz SP20 TscF SCKx Output Fall Time — — — ns See Parameter DO32 (Note 3) SP21 TscR SCKx Output Rise Time — — — ns See Parameter DO31 (Note 3) SP30 TdoF SDOx Data Output Fall Time — — — ns See Parameter DO32 (Note 3) SP31 TdoR SDOx Data Output Rise Time — — — ns See Parameter DO31 (Note 3) SP35 TscH2doV, SDOx Data Output Valid After TscL2doV SCKx Edge — 6 20 ns SP36 TdiV2scH, SDOx Data Output Setup to TdiV2scL First SCKx Edge 30 — — ns Using PPS pins 3 — — ns SPI2 dedicated pins Note 1: 2: 3: These parameters are characterized but not tested in manufacturing. Data in “Typ.” column are at 3.3V, +25°C unless otherwise stated. Assumes 50 pF load on all SPIx pins. DS70005319D-page 748  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 24-9: SPIx MASTER MODE (FULL-DUPLEX, CKE = 1, CKP = x, SMP = 1) TIMING CHARACTERISTICS SP36 SCKx (CKP = 0) SP10 SP21 SP20 SP20 SP21 SCKx (CKP = 1) SP35 SDOx MSb LSb SP30, SP31 SP40 SDIx Bit 14 - - - - - -1 MSb In Bit 14 - - - -1 LSb In SP41 Note: Refer to Figure 24-1 for load conditions. TABLE 24-36: SPIx MASTER MODE (FULL-DUPLEX, CKE = 1, CKP = x, SMP = 1) TIMING REQUIREMENTS AC CHARACTERISTICS Param No. Symbol SP10 FscP SP20 SP21 SP30 TscF TscR TdoF SP31 SP35 SP36 Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Characteristic(1) Min. Typ.(2) Max. Units Maximum SCKx Frequency — — — — — — — — — — 15 40 — — — MHz MHz ns ns ns Using PPS pins SPI2 dedicated pins See Parameter DO32 (Note 3) See Parameter DO31 (Note 3) See Parameter DO32 (Note 3) — — — ns See Parameter DO31 (Note 3) — 6 20 ns SCKx Output Fall Time SCKx Output Rise Time SDOx Data Output Fall Time TdoR SDOx Data Output Rise Time TscH2doV, SDOx Data Output Valid TscL2doV After SCKx Edge TdoV2sc, SDOx Data Output Setup TdoV2scL to First SCKx Edge 30 — — ns 3 — — ns SP40 TdiV2scH, Setup Time of SDIx Data 30 — — ns TdiV2scL Input to SCKx Edge 20 — — ns SP41 TscH2diL, Hold Time of SDIx Data 30 — — ns TscL2diL Input to SCKx Edge 15 — — ns Note 1: These parameters are characterized but not tested in manufacturing. 2: Data in “Typ.” column are at 3.3V, +25°C unless otherwise stated. 3: Assumes 50 pF load on all SPIx pins.  2017-2019 Microchip Technology Inc. Conditions Using PPS pins SPI2 dedicated pins Using PPS pins SPI2 dedicated pins Using PPS pins SPI2 dedicated pins DS70005319D-page 749 dsPIC33CH128MP508 FAMILY FIGURE 24-10: SPIx MASTER MODE (FULL-DUPLEX, CKE = 0, CKP = x, SMP = 1) TIMING CHARACTERISTICS SCKx (CKP = 0) SP10 SP21 SP20 SP20 SP21 SCKx (CKP = 1) SP35 SP36 SDOx MSb Bit 14 - - - - - -1 SP30, SP31 SDIx MSb In LSb SP30, SP31 Bit 14 - - - -1 LSb In SP40 SP41 Note: Refer to Figure 24-1 for load conditions. TABLE 24-37: SPIx MASTER MODE (FULL-DUPLEX, CKE = 0, CKP = x, SMP = 1) TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended AC CHARACTERISTICS Param No. Symbol Characteristic(1) Min. Typ.(2) Max. Units Conditions — — — 15 40 — MHz MHz ns Using PPS pins SPI2 dedicated pins See Parameter DO32 (Note 3) See Parameter DO31 (Note 3) See Parameter DO32 (Note 3) See Parameter DO31 (Note 3) SP10 FscP Maximum SCKx Frequency SP20 TscF SCKx Output Fall Time — — — SP21 TscR SCKx Output Rise Time — — — ns SP30 TdoF SDOx Data Output Fall Time — — — ns SP31 TdoR SDOx Data Output Rise Time — — — ns SP35 TscH2doV, TscL2doV TdoV2scH, TdoV2scL SDOx Data Output Valid After SCKx Edge SDOx Data Output Setup to First SCKx Edge — 6 20 ns 30 — — 20 — — SP40 TdiV2scH, Setup Time of SDIx Data 30 — — TdiV2scL Input to SCKx Edge 10 — — SP41 TscH2diL, Hold Time of SDIx Data Input 30 — — TscL2diL to SCKx Edge 15 — — Note 1: These parameters are characterized but not tested in manufacturing. 2: Data in “Typ.” column are at 3.3V, +25°C unless otherwise stated. 3: Assumes 50 pF load on all SPIx pins. ns ns ns ns ns ns SP36 DS70005319D-page 750 Using PPS pins SPI2 dedicated pins Using PPS pins SPI2 dedicated pins Using PPS pins SPI2 dedicated pins  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 24-11: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = x, SMP = 0) TIMING CHARACTERISTICS SSx SP52 SP50 SCKx (CKP = 0) SP10 SP73 SP72 SP72 SP73 SCKx (CKP = 1) SP35 SP36 SDOx MSb Bit 14 - - - - - -1 LSb SP30, SP31 SDIx MSb In Bit 14 - - - -1 SP51 LSb In SP41 SP40 Note: Refer to Figure 24-1 for load conditions.  2017-2019 Microchip Technology Inc. DS70005319D-page 751 dsPIC33CH128MP508 FAMILY TABLE 24-38: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = x, SMP = 0) TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended AC CHARACTERISTICS Param No. Symbol Characteristic(1) Min. Typ.(2) Max. Units — — 15 MHz Using PPS pins SPI2 dedicated pins Conditions SP10 FscP Maximum SCKx Input Frequency — — 40 MHz SP72 TscF SCKx Input Fall Time — — — ns See Parameter DO32 (Note 3) SP73 TscR SCKx Input Rise Time — — — ns See Parameter DO31 (Note 3) SP30 TdoF SDOx Data Output Fall Time — — — ns See Parameter DO32 (Note 3) SP31 TdoR SDOx Data Output Rise Time — — — ns See Parameter DO31 (Note 3) SP35 TscH2doV, SDOx Data Output Valid After TscL2doV SCKx Edge — 6 20 ns SP36 TdoV2scH, SDOx Data Output Setup to TdoV2scL First SCKx Edge 30 — — ns 20 — — ns SPI2 dedicated pins SP40 TdiV2scH, TdiV2scL Setup Time of SDIx Data Input to SCKx Edge 30 — — ns Using PPS pins 10 — — ns SPI2 dedicated pins SP41 TscH2diL, TscL2diL Hold Time of SDIx Data Input to SCKx Edge 30 — — ns Using PPS pins 15 — — ns SPI2 dedicated pins SP50 TssL2scH, TssL2scL SSx  to SCKx  or SCKx  Input 120 — — ns SP51 TssH2doZ SSx  to SDOx Output High-Impedance 8 — 50 ns (Note 3) SP52 TscH2ssH, SSx After SCKx Edge TscL2ssH 1.5 TCY + 40 — — ns (Note 3) Note 1: 2: 3: Using PPS pins These parameters are characterized but not tested in manufacturing. Data in “Typ.” column are at 3.3V, +25°C unless otherwise stated. Assumes 50 pF load on all SPIx pins. DS70005319D-page 752  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 24-12: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = x, SMP = 0) TIMING CHARACTERISTICS SP60 SSx SP52 SP50 SCKx (CKP = 0) SP10 SP73 SCKx (CKP = 1) SP72 SP36 SP35 SP72 MSb SDOx Bit 14 - - - - - -1 LSb SP30, SP31 SDIx MSb In Bit 14 - - - -1 SP73 SP51 LSb In SP41 SP40 Note: Refer to Figure 24-1 for load conditions.  2017-2019 Microchip Technology Inc. DS70005319D-page 753 dsPIC33CH128MP508 FAMILY TABLE 24-39: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = x, SMP = 0) TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended AC CHARACTERISTICS Param No. SP10 Characteristic(1) Min. Typ.(2) Maximum SCKx Input Frequency — — Symbol FscP Max. Units Conditions — 15 MHz Using PPS pins — 40 MHz SPI2 dedicated pins SP72 TscF SCKx Input Fall Time — — — ns See Parameter DO32 (Note 3) SP73 TscR SCKx Input Rise Time — — — ns See Parameter DO31 (Note 3) SP30 TdoF SDOx Data Output Fall Time — — — ns See Parameter DO32 (Note 3) SP31 TdoR SDOx Data Output Rise Time — — — ns See Parameter DO31 (Note 3) SP35 TscH2doV, SDOx Data Output Valid After TscL2doV SCKx Edge — 6 20 ns SP36 TdoV2scH, SDOx Data Output Setup to TdoV2scL First SCKx Edge 30 — — ns 20 — — ns SPI2 dedicated pins SP40 TdiV2scH, TdiV2scL Setup Time of SDIx Data Input to SCKx Edge 30 — — ns Using PPS pins 10 — — ns SPI2 dedicated pins SP41 TscH2diL, TscL2diL Hold Time of SDIx Data Input to SCKx Edge 30 — — ns Using PPS pins 15 — — ns SPI2 dedicated pins SP50 TssL2scH, TssL2scL SSx  to SCKx  or SCKx  Input 120 — — ns SP51 TssH2doZ SSx  to SDOx Output High-Impedance 8 — 50 ns (Note 3) SP52 TscH2ssH, SSx After SCKx Edge TscL2ssH 1.5 TCY + 40 — — ns (Note 3) SP60 TssL2doV — — 50 ns Note 1: 2: 3: SDOx Data Output Valid After SSx Edge Using PPS pins These parameters are characterized but not tested in manufacturing. Data in “Typ.” column are at 3.3V, +25°C unless otherwise stated. Assumes 50 pF load on all SPIx pins. DS70005319D-page 754  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 24-13: I2Cx BUS START/STOP BITS TIMING CHARACTERISTICS (MASTER MODE) SCLx IM31 IM34 IM30 IM33 SDAx Stop Condition Start Condition Note: Refer to Figure 24-1 for load conditions. FIGURE 24-14: I2Cx BUS DATA TIMING CHARACTERISTICS (MASTER MODE) IM20 IM21 IM11 IM10 SCLx IM26 IM11 IM25 IM10 IM33 SDAx In IM40 IM40 IM45 SDAx Out Note: Refer to Figure 24-1 for load conditions.  2017-2019 Microchip Technology Inc. DS70005319D-page 755 dsPIC33CH128MP508 FAMILY TABLE 24-40: I2Cx BUS DATA TIMING REQUIREMENTS (MASTER MODE) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended AC CHARACTERISTICS Param Symbol No. IM10 IM11 IM20 IM21 IM25 IM26 IM30 IM31 IM33 IM34 IM40 IM45 IM50 IM51 Note 1: 2: 3: 4: Characteristic(4) Min.(1) Max. Units TCY (BRG + 1) — µs TLO:SCL Clock Low Time 100 kHz mode — µs 400 kHz mode TCY (BRG + 1) 1 MHz mode(2) TCY (BRG + 1) — µs THI:SCL Clock High Time 100 kHz mode TCY (BRG + 1) — µs — µs 400 kHz mode TCY (BRG + 1) 1 MHz mode(2) TCY (BRG + 1) — µs TF:SCL SDAx and SCLx 100 kHz mode — 300 ns Fall Time 300 ns 400 kHz mode 20 x (VDD/5.5V) 1 MHz mode(2) — 120 ns TR:SCL SDAx and SCLx 100 kHz mode — 1000 ns Rise Time 400 kHz mode 20 + 0.1 CB 300 ns 1 MHz mode(2) — 120 ns TSU:DAT Data Input 100 kHz mode 250 — ns Setup Time 400 kHz mode 100 — ns (2) 1 MHz mode 50 — ns THD:DAT Data Input 100 kHz mode 0 — µs Hold Time 400 kHz mode 0 0.9 µs 1 MHz mode(2) 0 0.3 µs TSU:STA Start Condition 100 kHz mode TCY (BRG + 1) — µs Setup Time 400 kHz mode TCY (BRG + 1) — µs 1 MHz mode(2) TCY (BRG + 1) — µs THD:STA Start Condition 100 kHz mode TCY (BRG + 1) — µs Hold Time 400 kHz mode TCY (BRG + 1) — µs 1 MHz mode(2) TCY (BRG + 1) — µs TSU:STO Stop Condition 100 kHz mode TCY (BRG + 1) — µs Setup Time 400 kHz mode TCY (BRG + 1) — µs (2) 1 MHz mode TCY (BRG + 1) — µs THD:STO Stop Condition 100 kHz mode TCY (BRG + 1) — µs Hold Time 400 kHz mode TCY (BRG + 1) — µs 1 MHz mode(2) TCY (BRG + 1) — µs TAA:SCL Output Valid 100 kHz mode — 3450 ns from Clock 400 kHz mode — 900 ns 1 MHz mode(2) — 450 ns TBF:SDA Bus Free Time 100 kHz mode 4.7 — µs 400 kHz mode 1.3 — µs 1 MHz mode(2) 0.5 — µs Bus Capacitive Loading — 400 pF CB TPGD Pulse Gobbler Delay 65 390 ns 2 BRG is the value of the I C Baud Rate Generator. Maximum Pin Capacitance = 10 pF for all I2Cx pins (for 1 MHz mode only). Typical value for this parameter is 130 ns. These parameters are characterized but not tested in manufacturing. DS70005319D-page 756 Conditions CB is specified to be from 10 to 400 pF CB is specified to be from 10 to 400 pF Only relevant for Repeated Start condition After this period, the first clock pulse is generated Time the bus must be free before a new transmission can start (Note 3)  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 24-15: I2Cx BUS START/STOP BITS TIMING CHARACTERISTICS (SLAVE MODE) SCLx IS31 IS34 IS30 IS33 SDAx Stop Condition Start Condition FIGURE 24-16: I2Cx BUS DATA TIMING CHARACTERISTICS (SLAVE MODE) IS20 IS21 IS11 IS10 SCLx IS30 IS25 IS31 IS26 IS33 SDAx In IS40 IS40 IS45 SDAx Out  2017-2019 Microchip Technology Inc. DS70005319D-page 757 dsPIC33CH128MP508 FAMILY TABLE 24-41: I2Cx BUS DATA TIMING REQUIREMENTS (SLAVE MODE) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended AC CHARACTERISTICS Param Symbol No. Characteristic(3) IS10 TLO:SCL Clock Low Time IS11 THI:SCL Clock High Time IS20 IS21 IS25 IS26 IS30 IS31 IS33 IS34 IS40 IS45 IS50 IS51 Note Min. Max. Units 100 kHz mode 400 kHz mode 1 MHz mode(1) 100 kHz mode 4.7 1.3 0.5 4.0 — — — — µs µs µs µs 400 kHz mode 0.6 — µs 1 MHz mode(1) 0.28 — µs SDAx and SCLx 100 kHz mode — 300 ns TF:SCL Fall Time 400 kHz mode 20 x (VDD/5.5V) 300 ns (1) 1 MHz mode 20 x (VDD/5.5V) 120 ns TR:SCL SDAx and SCLx 100 kHz mode 20 + 0.1 CB 1000 ns Rise Time 400 kHz mode 300 ns 1 MHz mode(1) — 120 ns TSU:DAT Data Input 100 kHz mode 250 — ns Setup Time 400 kHz mode 100 — ns 1 MHz mode(1) 50 — ns THD:DAT Data Input 100 kHz mode 0 — µs Hold Time 400 kHz mode 0 0.9 µs 1 MHz mode(1) 0 0.3 µs TSU:STA Start Condition 100 kHz mode 4.7 — µs Setup Time 400 kHz mode 0.6 — µs (1) 0.26 — µs 1 MHz mode THD:STA Start Condition 100 kHz mode 4.0 — µs Hold Time 400 kHz mode 0.6 — µs 0.26 — µs 1 MHz mode(1) TSU:STO Stop Condition 100 kHz mode 4 — µs Setup Time 400 kHz mode 0.6 — µs 1 MHz mode(1) 0.26 — µs THD:STO Stop Condition 100 kHz mode >0 — µs Hold Time 400 kHz mode >0 — µs 1 MHz mode(1) >0 µs TAA:SCL Output Valid from 100 kHz mode 0 3540 ns Clock 400 kHz mode 0 900 ns (1) 1 MHz mode 0 400 ns TBF:SDA Bus Free Time 100 kHz mode 4.7 — µs 400 kHz mode 1.3 — µs 0.5 — µs 1 MHz mode(1) CB Bus Capacitive Loading — 400 pF TPGD Pulse Gobbler Delay 65 390 ns 1: Maximum Pin Capacitance = 10 pF for all I2Cx pins (for 1 MHz mode only). 2: Typical value for this parameter is 130 ns. 3: These parameters are characterized but not tested in manufacturing. DS70005319D-page 758 Conditions Device must operate at a minimum of 1.5 MHz Device must operate at a minimum of 10 MHz CB is specified to be from 10 to 400 pF CB is specified to be from 10 to 400 pF Only relevant for Repeated Start condition After this period, the first clock pulse is generated Time the bus must be free before a new transmission can start (Note 2)  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY FIGURE 24-17: UARTx MODULE I/O TIMING CHARACTERISTICS UA20 UxRX UXTX MSb In Bit 6-1 LSb In UA10 TABLE 24-42: UARTx MODULE I/O TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +125°C AC CHARACTERISTICS Param No. Symbol Characteristic(1) UA10 TUABAUD UARTx Baud Time UA11 FBAUD UARTx Baud Frequency UA20 TCWF Start Bit Pulse Width to Trigger UARTx Wake-up Note 1: 2: Min. Typ.(2) Max. Units 66.67 — — ns — — 15 Mbps 500 — — ns Conditions These parameters are characterized but not tested in manufacturing. Data in “Typ.” column are at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only and are not tested.  2017-2019 Microchip Technology Inc. DS70005319D-page 759 dsPIC33CH128MP508 FAMILY TABLE 24-43: ADC MODULE SPECIFICATIONS Operating Conditions: 3.0V to 3.6V (unless otherwise stated)(4) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param No. Symbol Characteristics Min. Typical Max. Units — AVDD V Conditions Analog Input AD12 VINH-VINL Full-Scale Input Span AVSS AD14 VIN Absolute Input Voltage AVSS – 0.3 — AVDD + 0.3 V AD17 RIN Recommended Impedance of Analog Voltage Source — 100 —  AD66 VBG Internal Voltage Reference Source 1.14 1.2 1.26 V For minimum sampling time (Note 1) ADC Accuracy AD20c Nr Resolution 12 data bits bits AD21c INL Integral Nonlinearity > -11.3 — < 11.3 LSb AVSS = 0V, AVDD = 3.3V AD22c DNL Differential Nonlinearity > -1.5 — < 11.5 LSb AVSS = 0V, AVDD = 3.3V AD23c GERR Gain Error > -12 — < 12 LSb AVSS = 0V, AVDD = 3.3V AD24c EOFF Offset Error > 7.5 — < 7.5 LSb AVSS = 0V, AVDD = 3.3V AD31b SINAD Signal-to-Noise and Distortion 56 — 70 dB (Notes 2, 3) AD34b ENOB Effective Number of Bits 9 — 11.4 bits (Notes 2, 3) Dynamic Performance Note 1: 2: 3: 4: These parameters are not characterized or tested in manufacturing. These parameters are characterized but not tested in manufacturing. Characterized with a 1 kHz sine wave. The ADC module is functional at VBORMIN < VDD < VDDMIN, but with degraded performance. Unless otherwise stated, module functionality is ensured, but not characterized. DS70005319D-page 760  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 24-44: ANALOG-TO-DIGITAL CONVERSION TIMING SPECIFICATIONS AC CHARACTERISTICS Param Symbol No. Characteristics Min. 14.28 AD50 TAD ADC Clock Period AD51 FTP Throughput Rate Note 1: 2: Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)(2) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Typ.(1) Max. — — Units Conditions ns — — 3.5 Msps Dedicated Cores 0 and 1 — — 3.5 Msps Shared core These parameters are characterized but not tested in manufacturing. The ADC module is functional at VBORMIN < VDD < VDDMIN, but with degraded performance. Unless otherwise stated, module functionality is ensured, but not characterized. TABLE 24-45: HIGH-SPEED ANALOG COMPARATOR MODULE SPECIFICATIONS Operating Conditions: 3.0V to 3.6V (unless otherwise stated)(2) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Symbol No. Characteristic Min. Typ. Max. Units Comments CM09 FIN Input Frequency 400 500 550 MHz CM10 VIOFF Input Offset Voltage -20 — +20 mV CM11 VICM Input Common-Mode Voltage Range(1) AVSS — AVDD V CM13 CMRR Common-Mode Rejection Ratio 60 — — dB CM14 TRESP Large Signal Response — 15 — ns V+ input step of 100 mV while V- input is held at AVDD/2 CM15 VHYST Input Hysteresis 15 30 45 mV Depends on HYSSEL[1:0] Note 1: 2: These parameters are for design guidance only and are not tested in manufacturing. The comparator module is functional at VBORMIN < VDD < VDDMIN, but with degraded performance. Unless otherwise stated, module functionality is tested, but not characterized.  2017-2019 Microchip Technology Inc. DS70005319D-page 761 dsPIC33CH128MP508 FAMILY TABLE 24-46: DACx MODULE SPECIFICATIONS Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param No. Symbol Characteristic DA02 CVRES Resolution DA03 INL Integral Nonlinearity Error Min. Typ.(1) -38 — Max. Units 0 LSB 12 Comments bits DA04 DNL Differential Nonlinearity Error -5 — 5 LSB DA05 EOFF Offset Error -3.5 — 21.5 LSB Internal node at comparator input DA06 EG Gain Error 0 — 41 % Internal node at comparator input DA07 TSET Settling Time — 750 — ns Output with 2% of desired output voltage with a 5-95% or 95-5% step DA08 VOUT Voltage Output Range 0.165 — 3.135 V VDD = 3.3V Note 1: Parameters are for design guidance only and are not tested in manufacturing. TABLE 24-47: DACx OUTPUT (DACOUT1 PIN) SPECIFICATIONS Operating Conditions: 3.0V to 3.6V (unless otherwise stated)(1) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Symbol No. DA11 RLOAD DA11a CLOAD Characteristic Resistive Output Load Impedance Output Load Capacitance Min. Typ. Max. Units 10K — — Ohm — — 30 pF Comments Including output pin capacitance DA12 IOUT Output Current Drive Strength — 3 — mA Sink and source DA13 INL Integral Nonlinearity Error -50 — 0 LSB Includes INL of DACx module (DA03) DA14 DNL Differential Nonlinearity Error -5 — 5 LSB Includes DNL of DACx module (DA04) DA30 EOFF Offset Error -150 — 0 LSB Includes offset error of DACx module (DA05) DA31 EG Gain Error -146 — 0 LSB Includes gain error of DACx module (DA06) Note 1: The DACx module is functional at VBORMIN < VDD < VDDMIN, but with degraded performance. Unless otherwise stated, module functionality is tested, but not characterized. DS70005319D-page 762  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 24-48: PGAx MODULE SPECIFICATIONS AC/DC CHARACTERISTICS Param Symbol No. Characteristic Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)(1) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Min. Typ. Max. Units Comments PA01 VIN Input Voltage Range AVSS – 0.3 — AVDD + 0.3 V PA02 VCM Common-Mode Input Voltage Range AVSS — AVDD – 1.6 V PA03 PA04 VOS VOS Input Offset Voltage Input Offset Voltage Drift with Temperature -9 — — 15 +9 — mV µV/C PA05 RIN+ Input Impedance of Positive Input — >1M || 7 pF — || pF PA06 RIN- Input Impedance of Negative Input — 10K || 7 pF — || pF PA07 PA08 GERR LERR Gain Error Gain Nonlinearity Error -3 — 0.5 — +3 0.5 % % Gain = 4x, 8x,16x, 32x % of full scale, Gain = 16x PA09 IDD Current Consumption — 2.0 — mA Module is enabled with a 2-volt P-P output voltage swing Small Signal G = 4x Bandwidth (-3 dB) G = 8x G = 16x — 10 — MHz — — 5 2.5 — — MHz MHz PA10a BW PA10b PA10c PA10d PA11 OST G = 32x Output Settling Time to 1% of Final Value — — 1.25 0.4 — — MHz µs PA12 PA13 Output Slew Rate Gain Selection Time — — 40 1 — — V/µs µs SR TGSEL Gain = 32x Gain = 16x, 100 mV input step change Gain = 16x Module Turn-on/Setting Time — — 10 µs PA14 TON Note 1: The PGAx module is functional at VBORMIN < VDD < VDDMIN, but with degraded performance. Unless otherwise stated, module functionality is tested, but not characterized. TABLE 24-49: CONSTANT-CURRENT SOURCE SPECIFICATIONS Operating Conditions: 3.0V to 3.6V (unless otherwise stated)(1) Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Symbol No. Characteristic Min. Typ. Max. Units 8.8 — 12.0 µA Conditions CC03 I10SRC 10 µA Source Current CC04 I50SRC 50 µA Source Current 44 — 56 µA IBIASx pin CC05 I50SNK -44 — -56 µA IBIASx pin Note 1: 50 µA Sink Current ISRCx pin The constant-current source module is functional at VBORMIN < VDD < VDDMIN, but with degraded performance. Unless otherwise stated, module functionality is tested, but not characterized.  2017-2019 Microchip Technology Inc. DS70005319D-page 763 dsPIC33CH128MP508 FAMILY NOTES: DS70005319D-page 764  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 25.0 HIGH-TEMPERATURE ELECTRICAL CHARACTERISTICS This section provides an overview of the dsPIC33CH128MP508 family devices operating in an ambient temperature range of -40°C to +150°C. The specifications between -40°C to +150°C are identical to those shown in Section 24.0 “Electrical Characteristics” for operation between -40°C to +125°C, with the exception of the parameters listed in this section. Parameters in this section begin with an H, which denotes High temperature. Absolute maximum ratings for the dsPIC33CH128MP508 family high-temperature devices are listed below. Exposure to these maximum rating conditions for extended periods can affect device reliability. Functional operation of the device, at these or any other conditions above the parameters indicated in the operation listings of this specification, is not implied. Absolute Maximum Ratings(1) Ambient temperature under bias.............................................................................................................-40°C to +150°C Storage temperature .............................................................................................................................. -65°C to +150°C Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +4.0V Voltage on any pin that is not 5V tolerant with respect to VSS(3)..................................................... -0.3V to (VDD + 0.3V) Voltage on any 5V tolerant pin with respect to VSS when VDD  3.0V(3) ................................................... -0.3V to +5.5V Voltage on any 5V tolerant pin with respect to Vss when VDD < 3.0V(3) ................................................... -0.3V to +3.6V Maximum current out of VSS pin ...........................................................................................................................300 mA Maximum current into VDD pin(2) ...........................................................................................................................300 mA Maximum current sunk/sourced by any 4x I/O pin..................................................................................................15 mA Maximum current sunk/sourced by any 8x I/O pin ..................................................................................................25 mA Maximum current sunk by a group of I/Os between two VSS pins(4).......................................................................75 mA Maximum current sourced by a group of I/Os between two VDD pins(4) .................................................................75 mA Maximum current sunk by all I/Os(2,5) ...................................................................................................................200 mA Maximum current sourced by all I/Os(2,5)..............................................................................................................200 mA Note 1: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those, or any other conditions above those indicated in the operation listings of this specification, is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. 2: Maximum allowable current is a function of device maximum power dissipation (see Table 25-2). 3: See the “Pin Diagrams” section for the 5V tolerant pins. 4: Not applicable to AVDD and AVSS pins. 5: For 28-pin packages, the maximum current sunk/sourced by all I/Os is limited by 150 mA.  2017-2019 Microchip Technology Inc. DS70005319D-page 765 dsPIC33CH128MP508 FAMILY 25.1 DC Characteristics TABLE 25-1: OPERATING MIPS vs. VOLTAGE Maximum MIPS VDD Range Temperature Range (in °C) Master Slave 3.0V to 3.6V -40°C to +150°C 60 60 TABLE 25-2: THERMAL OPERATING CONDITIONS Rating Symbol Min. Max. Unit Operating Junction Temperature Range TJ -40 +165 °C Operating Ambient Temperature Range TA -40 +150 °C High-Temperature Devices Power Dissipation: Internal Chip Power Dissipation: PINT = VDD x (IDD –  IOH) PD PINT + PI/O W PDMAX (TJ – TA)/JA W I/O Pin Power Dissipation: I/O =  ({VDD – VOH} x IOH) +  (VOL x IOL) Maximum Allowed Power Dissipation TABLE 25-3: THERMAL PACKAGING CHARACTERISTICS(1) Characteristic Symbol Typ. Package Thermal Resistance, 80-Pin TQFP 12x12x1 mm JA 50.67 °C/W Package Thermal Resistance, 64-Pin TQFP 10x10x1.0 mm JA 45.7 °C/W Package Thermal Resistance, 64-Pin QFN 9x9 mm JA 18.7 °C/W Package Thermal Resistance, 48-Pin TQFP 7x7 mm JA 62.76 °C/W Package Thermal Resistance, 48-Pin UQFN 6x6 mm JA 27.6 °C/W Package Thermal Resistance, 36-Pin UQFN 5x5 mm JA 29.2 °C/W Package Thermal Resistance, 28-Pin UQFN 6x6 mm JA 22.41 °C/W Package Thermal Resistance, 28-Pin SSOP 5.30 mm JA 52.84 °C/W Note 1: Unit Junction to ambient thermal resistance, Theta-JA (JA) numbers are achieved by package simulations. DS70005319D-page 766  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 25-4: OPERATING VOLTAGE SPECIFICATIONS Operating Conditions: 3.0V to 3.6V (unless otherwise stated)(1) Operating temperature -40°C  TA  +150°C Para Symb m No. ol Characteristic Min. Typ. Max. Units Conditions Operating Voltage DC10 VDD Supply Voltage 3.0 — 3.6 V DC11 AVDD Supply Voltage Greater of: VDD – 0.3 or 3.0 — Lesser of: VDD + 0.3 or 3.6 V DC16 VPOR VDD Start Voltage to Ensure Internal Power-on Reset Signal — — VSS V DC17 SVDD VDD Rise Rate to Ensure Internal Power-on Reset Signal 0.03 — — V/ms BO10 VBOR 2.68 2.84 2.99 V Note 1: 2: BOR Event on VDD Transition High-to-Low(2) The difference between AVDD supply and VDD supply must not exceed ±300 mV at all times, including during device power-up 0V-3V in 100 ms Device is functional at VBORMIN < VDD < VDDMIN. Analog modules (ADC and comparators) may have degraded performance. Parameters are characterized but not tested.  2017-2019 Microchip Technology Inc. DS70005319D-page 767 dsPIC33CH128MP508 FAMILY TABLE 25-5: DC CHARACTERISTICS: OPERATING CURRENT (IDD) (MASTER RUN/SLAVE RUN)(2) Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +150°C Typ.(1) Max. Units HDC20 18.1 36 mA +150°C 3.3V 10 MIPS (N1 = 1, N2 = 5, N3 = 2, M = 50, FVCO = 400 MHz, FPLLO = 40 MHz) HDC21 22.2 40.3 mA +150°C 3.3V 20 MIPS (N1 = 1, N2 = 5, N3 = 1, M = 50, FVCO = 400 MHz, FPLLO = 80 MHz) HDC22 29.9 48.1 mA +150°C 3.3V 40 MIPS (N1 = 1, N2 = 3, N3 = 1, M = 60, FVCO = 480 MHz, FPLLO = 160 MHz) HDC23 46 61.7 mA +150°C 3.3V 60 MIPS (N1 = 1, N2 = 2, N3 = 1, M = 60, FVCO = 480 MHz, FPLLO = 240 MHz) Parameter No. Note 1: 2: Conditions Data in the “Typ.” column are for design guidance only and are not tested. Base Run current (IDD) is measured as follows: • Oscillator is switched to EC+PLL mode in software • OSC1 pin is driven with external 8 MHz square wave with levels from 0.3V to VDD – 0.3V • OSC2 is configured as an I/O in the Configuration Words (OSCIOFNC (FOSC[2]) = 0) • FSCM is disabled (FCKSM[1:0] (FOSC[7:6]) = 01) • Watchdog Timer is disabled (FWDT[15] = 0 and WDTCONL[15] = 0) • All I/O pins (except OSC1) are configured as outputs and driving low • No peripheral modules are operating or being clocked (defined PMDx bits are all ‘1’s) • JTAG is disabled (JTAGEN (FICD[5]) = 0) • NOP instructions are executed in while(1) loop TABLE 25-6: DC CHARACTERISTICS: OPERATING CURRENT (IDD) (MASTER SLEEP/SLAVE RUN) Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +150°C Typ.(1) Max. Units HDC20a 13.7 31.6 mA +150°C 3.3V 10 MIPS (N = 1, N2 = 5, N3 = 2, M = 50, FVCO = 400 MHz, FPLLO = 40 MHz) HDC21a 15.5 33.5 mA +150°C 3.3V 20 MIPS (N = 1, N2 = 5, N3 = 1, M = 50, FVCO = 400 MHz, FPLLO = 80 MHz) HDC22a 19.4 37.5 mA +150°C 3.3V 40 MIPS (N = 1, N2 = 3, N3 = 1, M = 60, FVCO = 480 MHz, FPLLO = 160 MHz) HDC23a 29 43 mA +150°C 3.3V 60 MIPS (N1 = 1, N2 = 2, N3 = 1, M = 60, FVCO = 480 MHz, FPLLO = 240 MHz) Parameter No. Note 1: Conditions Data in the “Typ.” column are for design guidance only and are not tested. DS70005319D-page 768  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 25-7: DC CHARACTERISTICS: OPERATING CURRENT (IDD) (MASTER RUN/SLAVE SLEEP) DC CHARACTERISTICS Master (Run) + Slave (Sleep) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +150°C Typ.(1) Max. Units HDC20b 14.4 32.3 mA +150°C 3.3V 10 MIPS (N = 1, N2 = 5, N3 = 2, M = 50, FVCO = 400 MHz, FPLLO = 40 MHz) HDC21b 16.8 34.7 mA +150°C 3.3V 20 MIPS (N = 1, N2 = 5, N3 = 1, M = 50, FVCO = 400 MHz, FPLLO = 80 MHz) HDC22b 20.6 38.6 mA +150°C 3.3V 40 MIPS (N = 1, N2 = 3, N3 = 1, M = 60, FVCO = 480 MHz, FPLLO = 160 MHz) HDC23b 32 46.7 mA +150°C 3.3V 60 MIPS (N1 = 1, N2 = 3, N3 = 1, M = 60, FVCO = 480 MHz, FPLLO = 240 MHz) Parameter No. Conditions Operating Current (IDD) Note 1: Data in the “Typ.” column are for design guidance only and are not tested.  2017-2019 Microchip Technology Inc. DS70005319D-page 769 dsPIC33CH128MP508 FAMILY TABLE 25-8: DC CHARACTERISTICS: OPERATING CURRENT (IIDLE) (MASTER IDLE/SLAVE IDLE)(2) Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +150°C Typ.(1) Max. Units HDC40 15.5 33.5 mA +150°C 3.3V 10 MIPS (N1 = 1, N2 = 5, N3 = 2, M = 50, FVCO = 400 MHz, FPLLO = 40 MHz) HDC41 16.9 34.8 mA +150°C 3.3V 20 MIPS (N1 = 1, N2 = 5, N3 = 1, M = 50, FVCO = 400 MHz, FPLLO = 80 MHz) HDC42 20.4 38.3 mA +150°C 3.3V 40 MIPS (N1 = 1, N2 = 3, N3 = 1, M = 60, FVCO = 480 MHz, FPLLO = 160 MHz) HDC43 30 43.2 mA +150°C 3.3V 60 MIPS (N1 = 1, N2 = 2, N3 = 1, M = 60, FVCO = 480 MHz, FPLLO = 240 MHz) Parameter No. Note 1: 2: Conditions Data in the “Typ.” column are for design guidance only and are not tested. Base Idle current (IIDLE) is measured as follows: • Oscillator is switched to EC+PLL mode in software • OSC1 pin is driven with external 8 MHz square wave with levels from 0.3V to VDD – 0.3V • OSC2 is configured as an I/O in the Configuration Words (OSCIOFNC (FOSC[2]) = 0) • FSCM is disabled (FCKSM[1:0] (FOSC[7:6]) = 01) • Watchdog Timer is disabled (FWDT[15] = 0 and WDTCONL[15] = 0) • All I/O pins (except OSC1) are configured as outputs and driving low • No peripheral modules are operating or being clocked (defined PMDx bits are all ‘1’s) • JTAG is disabled (JTAGEN (FICD[5]) = 0) • Flash in standby with NVMSIDL (NVMCON[12]) = 1 DS70005319D-page 770  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 25-9: DC CHARACTERISTICS: IDLE CURRENT (IIDLE) (MASTER IDLE/SLAVE SLEEP)(2) Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +150°C Typ.(1) Max. Units HDC40a 13 30.9 mA +150°C 3.3V 10 MIPS (N1 = 1, N2 = 5, N3 = 2, M = 50, FVCO = 400 MHz, FPLLO = 40 MHz) HDC41a 13.8 31.7 mA +150°C 3.3V 20 MIPS (N1 = 1, N2 = 5, N3 = 1, M = 50, FVCO = 400 MHz, FPLLO = 80 MHz) HDC42a 15.6 33.5 mA +150°C 3.3V 40 MIPS (N1 = 1, N2 = 3, N3 = 1, M = 60, FVCO = 480 MHz, FPLLO = 160 MHz) HDC43a 21.9 35.4 mA +150°C 3.3V 60 MIPS (N1 = 1, N2 = 2, N3 = 1, M = 60, FVCO = 480 MHz, FPLLO = 240 MHz) Parameter No. Note 1: 2: Conditions Data in the “Typ.” column are for design guidance only and are not tested. Base Idle current (IIDLE) is measured as follows: • Oscillator is switched to EC+PLL mode in software • OSC1 pin is driven with external 8 MHz square wave with levels from 0.3V to VDD – 0.3V • OSC2 is configured as an I/O in the Configuration Words (OSCIOFNC (FOSC[2]) = 0) • FSCM is disabled (FCKSM[1:0] (FOSC[7:6]) = 01) • Watchdog Timer is disabled (FWDT[15] = 0 and WDTCONL[15] = 0) • All I/O pins (except OSC1) are configured as outputs and driving low • No peripheral modules are operating or being clocked (defined PMDx bits are all ‘1’s) • JTAG is disabled (JTAGEN (FICD[5]) = 0) • Flash in standby with NVMSIDL (NVMCON[12]) = 1  2017-2019 Microchip Technology Inc. DS70005319D-page 771 dsPIC33CH128MP508 FAMILY TABLE 25-10: DC CHARACTERISTICS: IDLE CURRENT (IIDLE) (MASTER SLEEP/SLAVE IDLE)(2) Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +150°C Typ.(1) Max. Units HDC40b 12.5 30.4 mA +150°C 3.3V 10 MIPS (N1 = 1, N2 = 5, N3 = 2, M = 50, FVCO = 400 MHz, FPLLO = 40 MHz) HDC41b 13.2 31 mA +150°C 3.3V 20 MIPS (N1 = 1, N2 = 5, N3 = 1, M = 50, FVCO = 400 MHz, FPLLO = 80 MHz) HDC42b 14.8 32.7 mA +150°C 3.3V 40 MIPS (N1 = 1, N2 = 3, N3 = 1, M = 60, FVCO = 480 MHz, FPLLO = 160 MHz) HDC43b 22.9 34.3 mA +150°C 3.3V 60 MIPS (N1 = 1, N2 = 2, N3 = 1, M = 60, FVCO = 480 MHz, FPLLO = 240 MHz) Parameter No. Note 1: 2: Conditions Data in the “Typ.” column are for design guidance only and are not tested. Base Idle current (IIDLE) is measured as follows: • Oscillator is switched to EC+PLL mode in software • OSC1 pin is driven with external 8 MHz square wave with levels from 0.3V to VDD – 0.3V • OSC2 is configured as an I/O in the Configuration Words (OSCIOFNC (FOSC[2]) = 0) • FSCM is disabled (FCKSM[1:0] (FOSC[7:6]) = 01) • Watchdog Timer is disabled (FWDT[15] = 0 and WDTCONL[15] = 0) • All I/O pins (except OSC1) are configured as outputs and driving low • No peripheral modules are operating or being clocked (defined PMDx bits are all ‘1’s) • JTAG is disabled (JTAGEN (FICD[5]) = 0) • Flash in standby with NVMSIDL (NVMCON[12]) = 1 DS70005319D-page 772  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 25-11: POWER-DOWN CURRENT (IPD)(2) Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +150°C Parameter No. HDC60 Note 1: 2: Characteristic Base Power-Down Current Typ.(1) Max. Units 9.7 25.5 mA Conditions +150°C 3.3V Data in the “Typ.” column are for design guidance only and are not tested. Base Sleep current (IPD) is measured as follows: • OSC1 pin is driven with external 8 MHz square wave with levels from 0.3V to VDD – 0.3V • OSC2 is configured as an I/O in the Configuration Words (OSCIOFNC (FOSC[2]) = 0) • FSCM is disabled (FCKSM[1:0] (FOSC[7:6]) = 01) • Watchdog Timer is disabled (FWDT[15] = 0 and WDTCONL[15] = 0) • All I/O pins (except OSC1) are configured as outputs and driving low • No peripheral modules are operating or being clocked (defined PMDx bits are all ‘1’s) • JTAG is disabled (JTAGEN (FICD[5]) = 0) • The regulators are in Standby mode (VREGS (RCON[8]) = 0) • The regulators are in Low-Power mode (LPWREN (VREGCON[15]) = 1) TABLE 25-12: WATCHDOG TIMER DELTA CURRENT (IWDT)(1) Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +150°C Parameter No. HDC61 Note 1: Typ. Max. Units 8 — µA Conditions +150°C 3.3V The IWDT current is the additional current consumed when the module is enabled. This current should be added to the base IPD current. All parameters are characterized but not tested during manufacturing.  2017-2019 Microchip Technology Inc. DS70005319D-page 773 dsPIC33CH128MP508 FAMILY TABLE 25-13: PWM DELTA CURRENT(1) Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +150°C Parameter No. Typ. Max. Units HDC100 6.5 8.2 mA +150°C 3.3V PWM Output Frequency = 500 kHz, PWM Input (AFPLLO = 500 MHz) (AVCO = 1000 MHz, PLLFBD = 125, APLLDIV1 = 2) HDC101 5 5.7 mA +150°C 3.3V PWM Output Frequency = 500 kHz, PWM Input (AFPLLO = 400 MHz), (AVCO = 400 MHz, PLLFBD = 50, APLLDIV1 = 1) HDC102 2.8 3.4 mA +150°C 3.3V PWM Output Frequency = 500 kHz, PWM Input (AFPLLO = 200 MHz), (AVCO = 400 MHz, PLLFBD = 50, APLLDIV1 = 2) HDC103 1.5 2.3 mA +150°C 3.3V PWM Output Frequency = 500 kHz, PWM Input (AFPLLO = 100 MHz), (AVCO = 400 MHz, PLLFBD = 50, APLLDIV1 = 4) Note 1: Conditions APLL current is not included. The APLL current will be the same if more than one PWM is running. Listed delta currents are for only one PWM instance when HREN = 0 (PGxCONL[7]). All parameters are characterized but not tested during manufacturing. TABLE 25-14: APLL DELTA CURRENT Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +150°C Parameter No. Conditions(1) Typ. Max. Units HDC110 — 23 mA +150°C 3.3V AFPLLO = 500 MHz (AVCO = 1000 MHz, PLLFBD = 125, APLLDIV1 = 2) HDC111 — 16 mA +150°C 3.3V AFPLLO = 400 MHz (AVCO = 400 MHz, PLLFBD = 50, APLLDIV1 = 1) HDC112 — 15 mA +150°C 3.3V AFPLLO = 200 MHz (AVCO = 400 MHz, PLLFBD = 50, APLLDIV1 = 2) HDC113 — 15 mA +150°C 3.3V AFPLLO = 100 MHz (AVCO = 400 MHz, PLLFBD = 50, APLLDIV1 = 4) Note 1: The APLL current will be the same if more than one PWM or DAC is run to the APLL clock. All parameters are characterized but not tested during manufacturing. DS70005319D-page 774  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 25-15: ADC DELTA CURRENT(1,2) Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +150°C Parameter No. HDC120 Note 1: 2: Master Slave Typ. Max. Typ. Max. — 8.5 — Units 16.3 mA Conditions +150°C 3.3V TAD = 14.3 ns (3.5 Msps conversion rate) Master shared core continuous conversion; TAD = 14.3 nS (3.5 Msps Conversion rate). Slave dedicated core continuous conversion on all 3 SAR cores; TAD = 14.3 nS (3.5 Msps conversion rate). All parameters are characterized but not tested during manufacturing. TABLE 25-16: COMPARATOR + DAC DELTA CURRENT Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +150°C Parameter No. HDC130 Note 1: Typ. Max. Units — 5 mA Conditions +150°C 3.3V AFPLLO @ 500 MHz(1) APLL current is not included. Listed delta currents are for only one comparator + DAC instance. All parameters are characterized but not tested during manufacturing. TABLE 25-17: PGAx DELTA CURRENT(1) Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +150°C Parameter No. Typ. Max. Units — 3 mA HDC141 Note 1: Conditions +150°C 3.3V All parameters are characterized but not tested during manufacturing.  2017-2019 Microchip Technology Inc. DS70005319D-page 775 dsPIC33CH128MP508 FAMILY TABLE 25-18: I/O PIN INPUT SPECIFICATIONS Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +150°C Param Symbol No. Conditions Input Leakage Current(2) HDI50 IIL Note 1: 2: 3: 4: 5: Min.(4) Typ.(1) Max.(5) Units Characteristic I/O Pins 5V Tolerant(3) -800 — 800 nA I/O Pins Not 5V Tolerant(3) -800 — 800 nA MCLR -800 — 800 nA OSCI -800 — 800 nA XT and HS modes Data in the “Typ.” column are at 3.3V, +25°C unless otherwise stated. Negative current is defined as current sourced by the pin. See the “Pin Diagrams” section for the 5V tolerant I/O pins. VPIN = VSS. VPIN = VDD. TABLE 25-19: INTERNAL FRC ACCURACY Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +150°C Param No. Characteristic Min. Max. Units +4 % Conditions Internal FRC Accuracy @ FRC Frequency = 8 MHz(1) HF20 Note 1: FRC -4 -40°C  TA +150°C Frequency is calibrated at +25°C and 3.3V. TABLE 25-20: INTERNAL LPRC ACCURACY Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +150°C Param No. Characteristic Min. Max. Units -30 +30 % Conditions LPRC @ 32 kHz HF21 LPRC DS70005319D-page 776 -40°C  TA  +150°C  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY TABLE 25-21: ADC MODULE SPECIFICATIONS Operating Conditions: 3.0V to 3.6V (unless otherwise stated)(1) Operating temperature -40°C  TA  +150°C Param No. Symbol Characteristics Min. Typical Max. Units Conditions ADC Accuracy HAD23c GERR Gain Error > -17.5 — < 17.5 LSb AVSS = 0V, AVDD = 3.3V HAD24c EOFF Offset Error > -15 — < 15 LSb AVSS = 0V, AVDD = 3.3V Note 1: The ADC module is functional at VBORMIN < VDD < VDDMIN, but with degraded performance. Unless otherwise stated, module functionality is ensured, but not characterized. TABLE 25-22: DACx MODULE SPECIFICATIONS Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C  TA  +150°C Param No. Characteristic Min. Typ.(1) HDA03 INL Integral Nonlinearity Error -50 HDA05 EOFF Offset Error 0 HDA06 EG Gain Error 0 Note 1: Symbol Max. Units Comments — 0 LSB — 45 LSB Internal node at comparator input — 55 % Internal node at comparator input Parameters are for design guidance only and are not tested in manufacturing. TABLE 25-23: PGAx MODULE SPECIFICATIONS AC/DC CHARACTERISTICS Param Symbol No. Characteristic Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)(1) Operating temperature -40°C  TA  +150°C Min. Typ. Max. Units Comments Input Offset Voltage -11 — +11 mV Gain = 32x HPA03 VOS Note 1: The PGAx module is functional at VBORMIN < VDD < VDDMIN, but with degraded performance. Unless otherwise stated, module functionality is tested, but not characterized.  2017-2019 Microchip Technology Inc. DS70005319D-page 777 dsPIC33CH128MP508 FAMILY NOTES: DS70005319D-page 778  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 26.0 PACKAGING INFORMATION 26.1 Package Marking Information 28-Lead SSOP (5.30 mm) XXXXXXXXXXXX XXXXXXXXXXXX YYWWNNN dsPIC33CH64 MP202 1810017 28-Lead UQFN (6x6 mm) XXXXXXXX XXXXXXXX YYWWNNN XXXXXXX XXXXXXX XXXXXXX YYWWNNN Note: Example 33CH64MP 202 1810017 36-Lead UQFN (5x5 mm) Legend: XX...X Y YY WW NNN Example Example dsPIC33 CH64MP 203 1810017 Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Alphanumeric traceability code In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information.  2017-2019 Microchip Technology Inc. DS70005319D-page 779 dsPIC33CH128MP508 FAMILY 26.1 Package Marking Information (Continued) 48-Lead TQFP (7x7 mm) Example CH64MP 2041810 017 48-Lead UQFN (6x6 mm) XXXXXXX XXXXXXX XXXXXXX YYWWNNN 64-Lead TQFP (10x10x1 mm) XXXXXXXXXXX XXXXXXXXXXX XXXXXXXXXXX YYWWNNN 64-Lead QFN (9x9x0.9 mm) XXXXXXXXXXX XXXXXXXXXXX XXXXXXXXXXX YYWWNNN 80-Lead TQFP (12x12x1 mm) XXXXXXXXXXXX XXXXXXXXXXXX XXXXXXXXXXXX YYWWNNN DS70005319D-page 780 Example dsPIC33 CH64MP 205 1810017 Example dsPIC33CH64 MP206 1810017 Example dsPIC33CH64 MP206 1810017 Example dsPIC33CH64 MP208 1810017  2017-2019 Microchip Technology Inc. dsPIC33CH128MP508 FAMILY 26.2 Package Details /HDG3ODVWLF6KULQN6PDOO2XWOLQH 66 PP%RG\>6623@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ ' $ % 1 '$780$ '$780% ( (   ;E  H & $ % 7239,(: $ $ & $ $ 6($7,1* 3/$1( ;  & 6,'(9,(: $ + F / / 9,(:$$ 0LFURFKLS7HFKQRORJ\'UDZLQJ&5HY&6KHHWRI  2017-2019 Microchip Technology Inc. DS70005319D-page 781 dsPIC33CH128MP508 FAMILY /HDG3ODVWLF6KULQN6PDOO2XWOLQH 66 PP%RG\>6623@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ 8QLWV 'LPHQVLRQ/LPLWV 1XPEHURI3LQV 1 H 3LWFK 2YHUDOO+HLJKW $ 0ROGHG3DFNDJH7KLFNQHVV $ 6WDQGRII $ 2YHUDOO:LGWK ( 0ROGHG3DFNDJH:LGWK ( 2YHUDOO/HQJWK ' )RRW/HQJWK / )RRWSULQW / F /HDG7KLFNQHVV )RRW$QJOH E /HDG:LGWK 0,1         ƒ  0,//,0(7(56 120 0$;  %6&               5()   ƒ ƒ   Notes: 3LQYLVXDOLQGH[IHDWXUHPD\YDU\EXWPXVWEHORFDWHGZLWKLQWKHKDWFKHGDUHD 'LPHQVLRQV'DQG(GRQRWLQFOXGHPROGIODVKRUSURWUXVLRQV0ROGIODVKRU SURWUXVLRQVVKDOOQRWH[FHHGPPSHUVLGH 'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(
DSPIC33CH64MP203-E/M5 价格&库存

很抱歉,暂时无法提供与“DSPIC33CH64MP203-E/M5”相匹配的价格&库存,您可以联系我们找货

免费人工找货
DSPIC33CH64MP203-E/M5
  •  国内价格 香港价格
  • 1+40.892261+5.07267
  • 25+37.4451325+4.64505
  • 100+33.99278100+4.21679

库存:547