MIC809TYC3

MIC809/810 Microprocessor Reset Circuits General Description Features The MIC809 and MIC810 are inexpensive microprocessor supervisory circuits that monitor power supplies in microprocessor-based systems. • Precision voltage monitor for 3V, 3.3V, or 5V power supplies • /RESET remains valid with VCC as low as 1.4V for SOT-23 packaged part • /RESET remains valid with VCC as low as 1V for SC70-packaged part • Typically less than 15μA supply current for SOT-23 packaged part • 5µA (typical) supply current for SC70-packaged part • 140ms (minimum) reset pulse widths available • Available in 3-pin SOT-23 and SC-70 package The function of these devices is to assert a reset if the power supply drops below a designated reset threshold level. Several different reset threshold levels are available to accommodate 3V, 3.3V or 5V powered systems. The MIC809 has an active-low /RESET output, while the MIC810 offers an active-high RESET output. The reset output is guaranteed to remain asserted for a minimum of 140ms after VCC has risen above the designated reset threshold level. Having a push-pull output stage, the MIC809/810 does not require a pull-up resistor at the output. The MIC809/810 comes in a 3-pin SOT-23 and SC-70 package. The MIC809 is also available with a shorter reset timeout (30ms, minimum). Datasheets and support documentation are available on Micrel’s web site at: www.micrel.com. Applications • • • • • Portable equipment Intelligent instruments Critical microprocessor power monitoring Printers/computers Controllers Typical Application Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com July 6, 2015 Revision 3.0 Micrel, Inc. MIC809/810 Ordering Information(1) Part Number 3-Pin SOT-23 3-Pin SC-70 (2) Marking Threshold Voltage (V) Operating Temperature Range Lead Finish MIC809LUY MIC809LYC3 IL 4.63 –40°C to +85°C Pb-Free MIC809MUY MIC809MYC3 IM 4.38 –40°C to +85°C Pb-Free MIC809JUY MIC809JYC3 IJ 4.00 –40°C to +85°C Pb-Free MIC809TUY MIC809TYC3 IT 3.08 –40°C to +85°C Pb-Free MIC809SUY MIC809SYC3 IS 2.93 –40°C to +85°C Pb-Free MIC809RUY MIC809RYC3 IR 2.63 –40°C to +85°C Pb-Free MIC810LUY MIC810LYC3 JL 4.63 –40°C to +85°C Pb-Free MIC810MUY MIC810MYC3 JM 4.38 –40°C to +85°C Pb-Free MIC810JUY MIC810JYC3 JJ 4.00 –40°C to +85°C Pb-Free MIC810TUY MIC810TYC3 JT 3.08 –40°C to +85°C Pb-Free MIC810SUY MIC810SYC3 JS 2.93 –40°C to +85°C Pb-Free MIC810RUY MIC810RYC3 JR 2.63 –40°C to +85°C Pb-Free Note: 1. All devices available in Tape and Reel only (Order entry PN, add TR, i.e., MIC809LUY TR). Standard/full reel quantity is 3,000 pieces. Reel diameter is 7in, hub diameter is 2in, and width is 8mm. 2. Underbar symbol (__) may not be to scale. Pin Configuration 3-Pin MIC809 SOT-23 3-Pin MIC809 SC-70 (Top View) July 6, 2015 3-Pin MIC810 SOT-23 3-Pin MIC810 SC-70 (Top View) 2 Revision 3.0 Micrel, Inc. MIC809/810 Pin Description Pin Number MIC809 Pin Number MIC810 Pin Name 1 1 GND 2 N/A /RESET /RESET goes low if VCC falls below the reset threshold and remains asserted for one reset timeout period (140ms min.) after VCC exceeds the reset threshold. N/A 2 RESET RESET goes high if VCC falls below the reset threshold and remains asserted for one reset timeout period (140ms, minimum) after VCC exceeds the reset threshold. 3 3 VCC Pin Name IC Ground Pin. Power Supply Input. Part Numbering Conventions MIC809 SOT-23 MIC809 SC-70 July 6, 2015 3 Revision 3.0 Micrel, Inc. MIC809/810 Absolute Maximum Ratings(3) Operating Ratings(4) Terminal Voltage (VCC) ................................. –0.3V to +6.0V Input Current (VCC) ...................................................... 20mA Output Current (/RESET, RESET) .............................. 20mA Lead Temperature (soldering, 10s) ............................ 300°C Storage Temperature (TS) ........................... –65°C to 150°C Rate-of-Rise (VCC) ................................................... 100V/μs ESD Rating(5) .................................................... 3kV (SC-70) Operating Temperature Range MIC809 ................................................. –40°C to +85°C MIC810 ................................................. –40°C to +85°C Power Dissipation (TA = +70°C) ............................... 320mW Electrical Characteristics(6) For typical values, VCC = 5V for MIC8_L/M/J, VCC = 3.3V for MIC8_S/T, VCC = 3V for MIC8_R; TA = 25°C. Bold values indicate –40°C to ≤ TA ≤ +85°C; unless otherwise noted. Symbol VCC Parameter Operating Voltage Range Condition Min. TA = 0°C to 70°C (SOT-23) TA = –40°C to 85°C (SOT-23) TA = –40°C to 85°C (SC70) ICC VTH Supply Current Reset Voltage Threshold tRST Reset Timeout Period VOH /RESET Output Voltage (MIC809) Typ. Max. Units 1.4 5.5 V 1.6 5.5 V 1 5.5 V MIC809L/M/J, MIC810L/M/J (SOT-23) 9 15 MIC809L/M/J, MIC810L/M/J (SC-70) 5 15 VCC 1.6V, ISINK = 50µA, TA = –40°C to +85°C 0.3 1.8V < VCC < VTH (minimum), ISOURCE = 150µA 0.8 × VCC Units V V ISINK = 3.2mA, MIC810L/M/J 0.4 ISINK = 1.2mA, MIC810R/S/T 0.3 V Timing Diagram Reset Timing Diagram July 6, 2015 5 Revision 3.0 Micrel, Inc. MIC809/810 Functional Diagram July 6, 2015 6 Revision 3.0 Micrel, Inc. MIC809/810 Application Information Microprocessor Reset The /RESET (or RESET) pin is asserted whenever VCC falls below the reset threshold voltage. The /RESET pin remains asserted for a period of 140ms after VCC has risen above the reset threshold voltage. The reset function ensures the microprocessor is properly reset and powers up in a known condition after a power failure. /RESET will remain valid with VCC as low as 1.4V (1V for SC-70 package). VCC Transients The MIC809/810 are relatively immune to negative-going VCC glitches below the reset threshold. Typically, a negative-going transient 125mV below the reset threshold with duration of 2µs or less (SC70 package) will not cause a reset. Interfacing to Bidirectional Reset Pins The MIC809/810 can interface with µPs with bidirectional reset pins by connecting a 4.7kΩ resistor in series with the MIC809/810 output and the µP reset pin. /RESET Valid at Low Voltage A resistor can be added from the /RESET pin to ground to ensure the /RESET output remains low with VCC down to 0V. A 100kΩ resistor connected from the /RESET to ground is recommended. The resistor should be small enough to pull-down any stray leakage currents and large enough not to load the reset output (Figure 1). Figure 1. Reset Valid to VCC = 0V July 6, 2015 7 Revision 3.0 Micrel, Inc. MIC809/810 Package Information and Recommended Landing Patterns(7) 3-Pin SOT-23 (U) Note: 7. Package information is correct as of the publication date. For updates and most current information, go to www.micrel.com. July 6, 2015 8 Revision 3.0 Micrel, Inc. MIC809/810 Package Information and Recommended Landing Patterns(7) (Continued) 3-Pin SC-70 (C3) July 6, 2015 9 Revision 3.0 Micrel, Inc. MIC809/810 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com Micrel, Inc. is a leading global manufacturer of IC solutions for the worldwide high performance linear and power, LAN, and timing & communications markets. The Company’s products include advanced mixed-signal, analog & power semiconductors; high-performance communication, clock management, MEMs-based clock oscillators & crystal-less clock generators, Ethernet switches, and physical layer transceiver ICs. Company customers include leading manufacturers of enterprise, consumer, industrial, mobile, telecommunications, automotive, and computer products. Corporation headquarters and state-of-the-art wafer fabrication facilities are located in San Jose, CA, with regional sales and support offices and advanced technology design centers situated throughout the Americas, Europe, and Asia. Additionally, the Company maintains an extensive network of distributors and reps worldwide. Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this datasheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel’s terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2004 Micrel, Incorporated. July 6, 2015 10 Revision 3.0