PIC16LF18445T-I/SO

PIC16(L)F184XX Full-Featured, Low Pin Count Microcontrollers with XLP Product Brief Description PIC16(L)F184XX microcontrollers feature Intelligent Analog, Core Independent Peripherals (CIPs) and communication peripherals combined with eXtreme Low-Power (XLP) for a wide range of general purpose and low-power applications. Features such as a 12-bit Analog-to-Digital Converter with Computation (ADC2), Memory Access Partitioning (MAP), the Device Information Area (DIA), Powersaving operating modes, and Peripheral Pin Select (PPS), offer flexible solutions for a wide variety of custom applications. Core Features • • • • • • • • • • • • C Compiler Optimized RISC Architecture Only 48 instructions Operating Speed: – DC – 32 MHz clock input – 125 ns minimum instruction cycle Interrupt Capability 16-Level Deep Hardware Stack Timers: – Up to two 24-bit timers – Up to four 8-bit timers – Up to four 16-bit timers Low-Current Power-on Reset (POR) Configurable Power-up Timer (PWRTE) Brown-out Reset (BOR) Low-Power BOR (LPBOR) Option Windowed Watchdog Timer (WWDT): – Variable prescaler selection – Variable window size selection – Configurable in hardware (Configuration Words) and/or software Programmable Code Protection Memory • • • Up to 28 KB Program Flash Memory Up to 2 KB Data SRAM Memory 256B Data EEPROM © 2017 Microchip Technology Inc. Product Brief DS40001894B-page 1 PIC16(L)F184XX • • • • Direct, Indirect and Relative Addressing modes Memory Access Partition (MAP): – Write-protect – Customizable partition Device Information Area (DIA) Device Configuration Information (DCI) Operating Characteristics • • Operating Voltage Range: – 1.8V to 3.6V (PIC16LF184XX) – 2.3V to 5.5V (PIC16F184XX) Temperature Range: – Industrial: -40°C to 85°C – Extended: -40°C to 125°C Power-Saving Operation Modes • • • • Doze: CPU and Peripherals Running at Different Cycle Rates (typically CPU is lower) Idle: CPU Halted While Peripherals Operate Sleep: Lowest Power Consumption Peripheral Module Disable (PMD): – Ability to selectively disable hardware module to minimize active power consumption of unused peripherals eXtreme Low-Power (XLP) Features • • • • Sleep mode: 50 nA @ 1.8, typical Watchdog Timer: 500 nA @ 1.8V, typical Secondary Oscillator: 500 nA @ 32 kHz Operating Current: – 8 uA @ 32 kHz, 1.8V, typical – 32 uA/MHz @ 1.8V, typical Digital Peripherals • • • Configurable Logic Cell (CLC): – 4 CLCs – Integrated combinational and sequential logic Complementary Waveform Generator (CWG): – Up to 3 CWGs – Rising and falling edge dead-band control – Full-bridge, half-bridge, 1-channel drive – Multiple signal sources Capture/Compare/PWM (CCP) modules: © 2017 Microchip Technology Inc. Product Brief DS40001894B-page 2 PIC16(L)F184XX • • • • • • • – Up to 5 CCPs – 16-bit resolution for Capture/Compare modes – 10-bit resolution for PWM mode Pulse-Width Modulators (PWM): – 2 10-bit PWMs Numerically Controlled Oscillator (NCO): – Precision linear frequency generator (@50% duty cycle) with 0.0001% step size of source input clock – Input Clock: 0 Hz < fNCO < 32 MHz – Resolution: fNCO/220 Peripheral Pin Select (PPS): – I/O pin remapping of digital peripherals Serial Communications: – EUSART • Up to 2 EUSARTs • RS-232, RS-485, LIN compatible • Auto-Baud Detect, Auto-wake-up on Start. – Master Synchronous Serial Port (MSSP) • Up to 2 MSSPs • SPI ™ • I2C, SMBus and PMBus compatible Data Signal Modulator (DSM) – Modulates a carrier signal with digital data to create custom carrier synchronized output waveforms Up to 26 I/O Pins: – Individually programmable pull-ups – Slew rate control – Interrupt-on-change with edge-select – Input level selection control (ST or TTL) – Digital open-drain enable Timer modules: – Timer0: • 8/16-bit timer/counter • Synchronous or asynchronous operation • Programmable prescaler/postscaler • Time base for capture/compare function – Timer1/3/5 with gate control: • 16-bit timer/counter • Programmable internal or external clock sources • Multiple gate sources • Multiple gate modes • Time base for capture/compare function – Timer2/4/6 with Hardware Limit Timer: • 8-bit timers © 2017 Microchip Technology Inc. Product Brief DS40001894B-page 3 PIC16(L)F184XX – • Programmable prescaler/postscaler • Time base for PWM function • Hardware Limit (HLT) and one-shot extensions • Selectable clock sources Signal Measurement Timer (SMT) • Up to 2 SMTs • 24-bit timer/counter with programmable prescaler Analog Peripherals • • • • • • Analog-to-Digital Converter (ADC): – 12-bit with up to 24 external channels – Conversion available during Sleep – Automated post-processing – Automated math functions on input signals: • Averaging, filter calculations, oversampling and threshold comparison – Integrated charge pump for low-voltage operation – CVD support Zero-Cross Detect (ZCD): – AC high voltage zero-crossing detection for simplifying TRIAC control – Synchronized switching control and timing Temperature Sensor Circuit Comparator: – 2 Comparators – Fixed Voltage Reference at (non)inverting input(s) – Comparator outputs externally accessible Digital-to-Analog Converter (DAC): – 5-bit resolution, rail-to-rail – Positive Reference Selection – Unbuffered I/O pin output – Internal connections to ADCs and comparators Fixed Voltage Reference (FVR) module: – 1.024V, 2.048V and 4.096V output levels Flexible Oscillator Structure • • • • • High-Precision Internal Oscillator: – Software-selectable frequency range up to 32 MHz – ±2% at calibration (nominal) 4x PLL for use with external sources – up to 32 MHz (4-8 MHz input) 2x PLL for use with the HFINTOSC – up to 32 MHz Low-Power Internal 31 kHz Oscillator (LFINTOSC) External 32.768 kHz Crystal Oscillator (SOCS) © 2017 Microchip Technology Inc. Product Brief DS40001894B-page 4 PIC16(L)F184XX • External Oscillator Block with: – Three crystal/resonator modes up to 20 MHz – Three external clock modes up to 32 MHz – Fail-Safe Clock Monitor • Detects clock source failure – Oscillator Start-up Timer (OST) • Ensures stability of crystal oscillator sources Family Types 1 1 4 1 Y Y Y Y Y Y I PIC16(L)F18425 8192 14 256 1024 12 11 1 2 2 1 4/4 4 2 1 1 2 4 1 Y Y Y Y Y Y I PIC16(L)F18426 16384 28 256 2048 12 11 1 2 2 1 4/4 4 2 1 1 2 4 1 Y Y Y Y Y Y I PIC16(L)F18444 4096 7 256 512 12 17 1 2 2 1 4/4 4 2 1 1 1 4 1 Y Y Y Y Y Y I PIC16(L)F18445 8192 14 256 1024 12 17 1 2 2 1 4/4 4 2 1 1 2 4 1 Y Y Y Y Y Y I PIC16(L)F18446 16384 28 256 2048 12 17 1 2 2 1 4/4 4 2 1 1 2 4 1 Y Y Y Y Y Y I PIC16(L)F18455 8192 14 256 1024 26 24 1 2 3 1 4/4 5 2 1 2 2 4 1 Y Y Y Y Y Y I PIC16(L)F18456 16384 28 256 2048 26 24 1 2 3 1 4/4 5 2 1 2 2 4 1 Y Y Y Y Y Y I Note:  1. I - Debugging integrated on chip. 2. One pin is input-only. Packages TSSOP UQFN (4x4) ● ● ● ● ● ● ● PIC16(L)F18426 ● ● ● ● PIC16(L)F18444 ● ● Packages PDIP SOIC PIC16(L)F18424 ● PIC16(L)F18425 © 2017 Microchip Technology Inc. Product Brief SSOP ● ● DS40001894B-page 5 Debug(1) DSM Device Information Area CLC Memory Access Partition MSSP (I2C/SPI) Windowed Watchdog Timer EUSART 1 PMD NCO 2 XLP PWM 1 4/4 4 PPS CCP Timers (8/16-bit) CWG 2 Clock Ref Comparators 2 PIC16(L)F18424 4096 I/O’s(2) 7 256 512 12 11 1 Device 5-bit DAC 12-bit ADC (ch) Data SRAM (bytes) Data Memory (EEPROM) (bytes) Program Flash Memory (Kbytes) Program Flash Memory (Words) Table 1. PIC16(L)F184XX Family Types PIC16(L)F184XX Packages TSSOP UQFN (4x4) PDIP SOIC SSOP PIC16(L)F18445 ● ● ● ● PIC16(L)F18446 ● ● ● ● PIC16(L)F18455 ● ● ● ● PIC16(L)F18456 ● ● ● ● Note:  Pin details are subject to change. Important:  For other small form-factor package availability and marking information, visit www.microchip.com/ packaging or contact your local sales office. Pin Diagrams 14/16-Pin Diagrams Figure 1. 14-Pin PDIP, SOIC, TSSOP Rev. 00-000014A 6/21/2017 VDD 1 RA5 2 14 13 RA4 3 12 RA1/ICSPCLK VSS RA0/ICSPDAT MCLR/VPP/RA3 4 11 RA2 RC5 5 10 RC0 RC4 6 9 RC1 RC3 7 8 RC2 Figure 2. 16-Pin UQFN (4x4) NC VSS NC VDD Rev. 00-000016A 6/21/2017 16 15 14 13 RA5 1 12 RA0/ICSPDAT RA4 2 11 RA1/ICSPCLK 9 RC0 5 6 7 8 RC1 RC5 4 RC2 10 RA2 RC3 MCLR/VPP/RA3 3 RC4 1 Note:  It is recommended that the exposed bottom pad be connected to VSS. Related Links 14/16-Pin Allocation Table © 2017 Microchip Technology Inc. Product Brief DS40001894B-page 6 PIC16(L)F184XX 20-Pin Diagrams Figure 3. 20-Pin PDIP, SOIC, TSSOP Rev. 00-000020A 6/21/2017 VDD 1 RA5 2 20 VSS 19 RA0/ICSPDAT RA4 3 18 RA1/ICSPCLK 17 RA2 MCLR/VPP/RA3 4 RC5 5 16 RC0 RC4 6 15 RC1 RC3 7 14 RC2 RC6 8 13 RB4 RC7 9 12 RB5 RB7 10 11 RB6 Figure 4. 20-Pin UQFN (4x4) RA0/ICSPDAT VSS VDD RA5 RA4 Rev. 00-000020B 6/21/2016 20 19 18 17 16 15 RA1/ICSPCLK MCLR/VPP/RA3 1 13 RC0 RC3 4 12 RC1 RC6 5 11 RC2 8 9 10 RB4 7 RB5 6 RB6 14 RA2 RC4 3 RB7 RC5 2 RC7 2 Note:  It is recommended that the exposed bottom pad be connected to VSS. Related Links 20-Pin Allocation Table © 2017 Microchip Technology Inc. Product Brief DS40001894B-page 7 Figure 5. 28-pin SPDIP, SSOP, SOIC Rev. 00-000 028A 3/6/201 7 MCLR/VPP /RE3 RA0 RA1 RA2 RA3 RA4 RA5 VSS RA7 RA6 RC0 RC1 RC2 RC3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 RB7/ICSPDAT RB6/ICSPCLK RB6 RB4 RB3 RB2 RB1 RB0 VDD VSS RC7 RC6 RC5 RC4 RA1 RA0 RE3/MCLR/VPP RB7/ICSPDAT RB6/ICSPCLK RB5 RB4 Figure 6. 28-pin UQFN Rev. 00-000028B 6/23/2017 28 27 26 25 24 23 22 RA2 RA3 RA4 RA5 VSS RA7 RA6 1 21 RB3 20 RB2 2 3 19 RB1 18 RB0 4 5 17 VDD 16 VSS 6 7 15 RC7 8 9 10 11 12 13 14 RC0 RC1 RC2 RC3 RC4 RC5 RC6 3 PIC16(L)F184XX Filename: 00-000028A.vsd Title: 28-pin DIP Last Edit: 3/6/2017 First Used: N/A Notes: Generic 28-pin dual in-line diagram 28-Pin Diagrams Note:  It is recommended that the exposed bottom pad be connected to VSS. Related Links 28-Pin Allocation Table © 2017 Microchip Technology Inc. Product Brief DS40001894B-page 8 PIC16(L)F184XX Pin Allocation Tables RA0 13 12 ANA0 — C1IN0+ — DAC1OUT1 MDSRC(1) — — — — SS2(1) Basic Pull-up Interrupts CLKR CLC EUSART ZCD MSSP CWG PWM CCP Timers DSM DAC NCO Comparator Reference ADC 16-pin UQFN 14/16-Pin Allocation Table 14-pin PDIP/SOIC/TSSOP I/O 1 ICDDAT — — — — IOCA0 Y ICSPDAT C1IN0 RA1 12 11 ANA1 ADCVREF+ ICDCLK — DAC1VREF+ — — — — — — — — — — IOCA1 Y C2IN0- RA2 11 10 RA3 4 3 ICSPCLK CWG1IN(1) ANA2 ADCVREF- — — DAC1VREF- — T0CKI(1) CCP3IN(1) — — — — — — — T6IN(1) — — CWG2IN(1) — ZCD1 — — — IOCA2 Y — — — — — IOCA3 Y INT0(1) MCLR — VPP CLKOUT T1G(1) RA4 3 2 ANA4 — — — — — SMT1WIN(1) — — — — — — — — IOCA4 Y SOSCO OSC2 T1CKI(1) RA5 2 1 ANA5 — — — — — T2IN(1) CLKIN — — — — — — CLCIN3(1) — IOCA5 Y SMT1SIG(1) SOSCI OSC1 SCK1(1) RC0 10 9 ANC0 — C2IN0+ — — — T5CKI(1) — — — — — — — IOCC0 Y — — — CLCIN2(1) — IOCC1 Y — SCL1(1,3,4) SDI1(1) C1IN1RC1 9 8 ANC1 — — — — T4IN(1) CCP4IN(1) — — SDA1(1,3,4) C2IN1- ANC2 RC2 8 7 C1IN2— ADACT(1) — — MDCARL(1) — — — — — — — — — IOCC2 Y — — — — T5G(1) CCP2IN(1) — — SS1(1) — — CLCIN0(1) — IOCC3 Y — — — — T3G(1) — — — CK1(1,3) CLCIN1(1) — IOCC4 Y — — — IOCC5 Y — C2IN2- C1IN3RC3 7 6 ANC3 — C2IN3- SCK2(1,5) RC4 6 5 ANC4 — — — SCL2(1,3,4,5) SDI2(1,5) RC5 5 4 ANC5 — — — — MDCARH(1) T3CKI(1) CCP1IN(1) — — RX1(1) — SDA2(1,3,4,5) DT1(1,3) VDD 1 16 — — — — — — — — — — — — — — — — — VDD VSS 14 13 — — — — — — — — — — — — — — — — — VSS CWG1A SDO1 — DSM1OUT TMR0OUT CCP1OUT PWM6OUT — DT1(3) — — — CWG2A SDO2 OUT(2) — — ADCGRDA — C1OUT NCO1OUT © 2017 Microchip Technology Inc. Product Brief CLC1OUT CLKR DS40001894B-page 9 — — — — — C2OUT — — — — — — — — — — — — — — CCP3OUT — CWG1B SCK1 CWG2B SCK2 CWG1C SCL1(3) CWG2C SCL2(3) CWG1D SDA1(3) CWG2D SDA2(3) — CCP4OUT — Basic Pull-up Interrupts CLKR CLC EUSART ZCD PWM7OUT MSSP CCP2OUT — CWG Timers DSM DAC — PWM — CCP — — ADCGRDB NCO Comparator Reference ADC 16-pin UQFN 14-pin PDIP/SOIC/TSSOP I/O PIC16(L)F184XX — CK1(3) CLC2OUT — — — — — TX1 CLC3OUT — — — — — — CLC4OUT — — — — Note:  1. This is a PPS re-mappable input signal. The input function may be moved from the default location shown to one of several other PORTx pins. 2. All digital output signals shown in these rows are PPS re-mappable. These signals may be mapped to output onto one of several PORTx pin options. 3. This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and PPS output registers. 4. These pins are configured for I2C logic levels. PPS assignments to the other pins will operate, but input logic levels will be standard TTL/ST as selected by the INLVL register, instead of the I2C specific or SMBUS input buffer thresholds. 5. MSSP2 is not available on the PIC16(L)F18424 or PIC16(L)F18444 devices. Basic Pull-up Interrupts CLKR CLC EUSART ZCD MSSP CWG PWM CCP Timers DSM DAC NCO Comparator Reference ADC 20-pin UQFN 20-Pin Allocation Table 20-pin PDIP/SOIC/TSSOP I/O 2 ICDDAT/ RA0 19 16 ANA0 — C1IN0+ — DAC1OUT1 — — — — — — — — — — IOCA0 Y ICSPDAT RA1 18 15 ANA1 ADCVREF + C1IN0— C2IN0- DAC1VREF MDSRC(1) + ICDCLK/ — — — — SS2(1) — — — — IOCA1 Y ICSPCLK CWG1IN(1) RA2 17 14 ANA2 ADCVREF- — — DAC1VREF- — T0CKI(1) — — — ZCD1 — CLCIN0(1) — IOCA2 Y — — — — — IOCA3 Y INT0(1) CWG2IN(1) MCLR RA3 4 1 — — — — — — — — — — VPP RA4 3 20 ANA4 — — — © 2017 Microchip Technology Inc. — — T1G(1) CCP4IN(1) Product Brief — — — — — — — DS40001894B-page 10 IOCA4 Y CLKOUT Basic Pull-up Interrupts CLKR CLC EUSART ZCD MSSP CWG PWM CCP Timers DSM DAC NCO Comparator Reference ADC 20-pin UQFN 20-pin PDIP/SOIC/TSSOP I/O PIC16(L)F184XX SOSCO SMT1WIN(1) OSC2 T1CKI(1) RA5 2 19 ANA5 — — — — — T2IN(1) CLKIN — — — — — — — — IOCA5 Y SMT1SIG(1) SOSCI OSC1 SDI1(1) RB4 13 10 ANB4 — — — — — T5G(1) — — — — — CLCIN2(1) — IOCB4 Y — CLCIN3(1) — IOCB5 Y — SDA1(1,3,4) SCK2(1,5) RB5 12 9 ANB5 — — — — — — CCP3IN(1) — — RX1(1) — SCL2(1,3,4,5) DT1(1,3) SCK1(1) RB6 11 8 ANB6 — — — — — — — — — — — — — IOCB6 Y — — CK1(1,3) — — IOCB7 Y — SCL1(1,3,4) SDI2(1,5) RB7 10 7 ANB7 — — — — — T6IN(1) — — — SDA2(1,3,4,5) T3CKI(1) RC0 16 13 ANC0 — C2IN0+ — — — — — — — — — — — IOCC0 Y — T3G(1) C1IN1RC1 15 12 ANC1 — — — — — — — — — — — — — IOCC1 Y — — — MDCARL(1) T5CKI(1) — — — — — — — — IOCC2 Y — — — — — CCP2IN(1) — — — — — CLCIN1(1) — IOCC3 Y — — C2IN1- ANC2 RC2 14 11 C1IN2— ADACT(1) C2IN2- C1IN3RC3 7 4 ANC3 — C2IN3- RC4 6 3 ANC4 — — — — — — — — — — — — — — IOCC4 Y RC5 5 2 ANC5 — — — — MDCARH(1) T4IN(1) CCP1IN(1) — — — — — — IOCC5 Y — RC6 8 5 ANC6 — — — — — — — — — — SS1(1) — — — — IOCC6 Y — 6 IOCC7 Y RC7 9 ANC7 — — — — — — — — — — — — — — VDD 1 18 — — — — — — — — — — — — — — — — — VDD VSS 20 17 — — — — — — — — — — — — — — — — — VSS CWG1A SDO1 — DSM1OUT CWG2A SDO2 CWG1B SCK1 CWG2B SCK2 — — ADCGRDA — C1OUT NCO1OUT TMR0OUT CCP1OUT PWM6OUT — — DT1(3) CLC1OUT CLKR — — — — CK1(3) CLC2OUT — — — OUT(2) — — ADCGRDB — C2OUT — © 2017 Microchip Technology Inc. — — — CCP2OUT PWM7OUT Product Brief — DS40001894B-page 11 — — — — — — — — — — — — — — — — — CCP3OUT — CWG1C SCL1(3) CWG2C SCL2(3) CWG1D SDA1(3) CWG2D SDA2(3) — CCP4OUT — TX1 CLC3OUT — — — — — — CLC4OUT — — — — Basic Pull-up Interrupts CLKR CLC EUSART ZCD MSSP CWG PWM CCP Timers DSM DAC NCO Comparator 27 Reference 28-pin UQFN 2 ADC 28-pin PDIP/SOIC/TSSOP I/O 28-Pin Allocation Table C1IN0RA0 ANA0 — — — — — — — — — — — CLCIN0(1) — IOCA0 Y — — — — — — — — — — — CLCIN1(1) — IOCA1 Y — — — — — — — — — — — IOCA2 Y — — C2IN0- C1IN1RA1 3 28 ANA1 — C2IN1- C1IN0+ RA2 4 1 ANA2 ADCVREF- DAC1VREF— DAC1OUT1 C2IN0+ RA3 5 2 ANA3 — DAC1VREF+ MDCARL(1) — — — — — — — — — IOCA3 Y RA4 6 3 ANA4 — — — — T0CKI(1) CCP5IN(1) — — — — — IOCA4 Y — 7 4 ANA5 — — — — — — — — — SS1(1) — RA5 MDCARH(1) MDSRC(1) — — — — IOCA5 Y — RA6 10 7 ANA6 — — — — — — — — — — — — — — IOCA6 Y ADCVREF+ C1IN1+ OSC2 CLKOUT RA7 9 6 ANA7 — — — — — — — — — — — — — — IOCA7 Y OSC1 CLKIN RB0 21 18 ANB0 — C2IN1+ — © 2017 Microchip Technology Inc. — — — CCP4IN(1) — CWG1IN(1) Product Brief — ZCD1 — Basic — Note:  1. This is a PPS re-mappable input signal. The input function may be moved from the default location shown to one of several other PORTx pins. 2. All digital output signals shown in these rows are PPS re-mappable. These signals may be mapped to output onto one of several PORTx pin options. 3. This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and PPS output registers. 4. These pins are configured for I2C logic levels. PPS assignments to the other pins will operate, but input logic levels will be standard TTL/ST as selected by the INLVL register, instead of the I2C specific or SMBUS input buffer thresholds. 5. MSSP2 is not available on the PIC16(L)F18424 or PIC16(L)F18444 devices. 3 Pull-up Interrupts CLKR CLC EUSART ZCD MSSP CWG PWM CCP Timers DSM DAC NCO Comparator Reference ADC 20-pin UQFN 20-pin PDIP/SOIC/TSSOP I/O PIC16(L)F184XX — — IOCB0 Y DS40001894B-page 12 INT0(1) RB1 22 19 ANB1 — — — — — — — CWG2IN(1) C1IN3- 23 20 ANB2 — — SCK2(1) Basic Pull-up Interrupts CLKR CLC EUSART — — — — IOCB1 Y — — — — — IOCB2 Y — SCL2(1,3) C2IN3RB2 ZCD MSSP CWG PWM CCP Timers DSM DAC NCO Comparator Reference ADC 28-pin UQFN 28-pin PDIP/SOIC/TSSOP I/O PIC16(L)F184XX — — — — — — CWG3IN(1) SDI2(1) SDA2(1,3)SS2(1) RB3 24 21 ANB3 — — — — — — — — — — — — — IOCB3 Y — — — — — — — — — IOCB4 Y — CCP3IN(1) — — — — — — — IOCB5 Y — — — — — — — IOCB6 Y C1IN2C2IN2- T5G(1) ANB4 RB4 25 22 RB5 26 23 RB6 27 24 — — — — — ANB5 — — — — — ANB6 — — — — — ADACT(1) SMT2WIN(1) T1G(1) SMT2SIG(1) — CK2(1,3) CLCIN2(1) ICSPCLK ICDCLK RB7 28 25 ANB7 — — — DAC1OUT2 — T6IN(1) RX2(1) — — — — — DT2(1,3) ICSPDAT — — IOCB7 Y ICDDAT T1CKI(1) T3CKI(1) RC0 11 8 ANC0 — — — — — — — — — — — — — IOCC0 Y SOSCO CCP2IN(1) CCP1IN(1) — — — — — — — IOCC1 Y SOSCI — — — — — — — IOCC2 Y — — — — — IOCC3 Y — — — — — IOCC4 Y — T3G(1) SMT1WIN(1) RC1 12 9 ANC1 — — — — — RC2 13 10 ANC2 — — — — — SMT1SIG(1) T5CKI(1) SCK1(1) RC3 14 11 ANC3 — — — — — T2IN(1) — — — RC4 15 12 ANC4 — — — — — — — — — RC5 16 13 ANC5 — — — — — T4IN(1) — — — — — — — — IOCC5 Y — RC6 17 14 ANC6 — — — — — — — — — — — — CK1(1,3) — IOCC6 Y — — IOCC7 Y — — IOCE3 Y SCL1(1,3) SDI1(1) SDA1(1,3) RX1(1) RC7 18 15 RE3 1 26 ANC7 — — — — — — — — — — — — — — — — — — — — — — — — — DT1(1,3) — MCLR VPP VDD 20 17 — — — — — — — — — — — — — — — — — VDD VSS 8 5 — — — — — — — — — — — — — — — — — VSS VSS 19 16 — — — — — — — — — — — — — — — — — VSS — — — CWG1A SDO1 OUT(2) — — ADCGRDA — C1OUT NCO1OUT — DSM1OUT TMR0OUT CCP1OUT PWM6OUT CWG2A DT1(3) — SDO2 DT2(3) CLC1OUT CLKR CWG3A © 2017 Microchip Technology Inc. Product Brief DS40001894B-page 13 Basic Pull-up Interrupts CLKR CLC EUSART ZCD MSSP CWG PWM CCP Timers DSM DAC NCO Comparator Reference ADC 28-pin UQFN 28-pin PDIP/SOIC/TSSOP I/O PIC16(L)F184XX CWG1B SCK1 — — ADCGRDB — C2OUT — — — — CCP2OUT PWM7OUT CWG2B CK1(3) — SCK2 CK2(3) CLC2OUT — — — — CLC3OUT — — — — — — — — — CWG3B CWG1C SCL1(3) — — — — — — — — — CCP3OUT — CWG2C TX1 — TX2 SCL2(3) CWG3C CWG1D SDA1(3) — — — — — — — — — CCP4OUT — CWG2D — — CLC4OUT — — — — — SDA2(3) CWG3D — — — — — — — — — CCP5OUT — — — Note:  1. This is a PPS re-mappable input signal. The input function may be moved from the default location shown to one of several other PORTx pins. 2. All digital output signals shown in these rows are PPS re-mappable. These signals may be mapped to output onto one of several PORTx pin options. 3. This is a bidirectional signal. For normal module operation, the firmware should map this signal to the same pin in both the PPS input and PPS output registers. © 2017 Microchip Technology Inc. Product Brief DS40001894B-page 14 PIC16(L)F184XX The Microchip Web Site Microchip provides online support via our web site at http://www.microchip.com/. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information: • • • Product Support – Data sheets and errata, application notes and sample programs, design resources, user’s guides and hardware support documents, latest software releases and archived software General Technical Support – Frequently Asked Questions (FAQ), technical support requests, online discussion groups, Microchip consultant program member listing Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives Customer Change Notification Service Microchip’s customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. To register, access the Microchip web site at http://www.microchip.com/. Under “Support”, click on “Customer Change Notification” and follow the registration instructions. Customer Support Users of Microchip products can receive assistance through several channels: • • • • Distributor or Representative Local Sales Office Field Application Engineer (FAE) Technical Support Customers should contact their distributor, representative or Field Application Engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http://www.microchip.com/support Microchip Devices Code Protection Feature Note the following details of the code protection feature on Microchip devices: • • • • Microchip products meet the specification contained in their particular Microchip Data Sheet. Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. Microchip is willing to work with the customer who is concerned about the integrity of their code. © 2017 Microchip Technology Inc. Product Brief DS40001894B-page 15 PIC16(L)F184XX • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Legal Notice Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights unless otherwise stated. Trademarks The Microchip name and logo, the Microchip logo, AnyRate, AVR, AVR logo, AVR Freaks, BeaconThings, BitCloud, CryptoMemory, CryptoRF, dsPIC, FlashFlex, flexPWR, Heldo, JukeBlox, KeeLoq, KeeLoq logo, Kleer, LANCheck, LINK MD, maXStylus, maXTouch, MediaLB, megaAVR, MOST, MOST logo, MPLAB, OptoLyzer, PIC, picoPower, PICSTART, PIC32 logo, Prochip Designer, QTouch, RightTouch, SAM-BA, SpyNIC, SST, SST Logo, SuperFlash, tinyAVR, UNI/O, and XMEGA are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. ClockWorks, The Embedded Control Solutions Company, EtherSynch, Hyper Speed Control, HyperLight Load, IntelliMOS, mTouch, Precision Edge, and Quiet-Wire are registered trademarks of Microchip Technology Incorporated in the U.S.A. Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, BodyCom, chipKIT, chipKIT logo, CodeGuard, CryptoAuthentication, CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM, ECAN, EtherGREEN, In-Circuit Serial Programming, ICSP, Inter-Chip Connectivity, JitterBlocker, KleerNet, KleerNet logo, Mindi, MiWi, motorBench, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, PureSilicon, QMatrix, RightTouch logo, REAL ICE, Ripple Blocker, SAM-ICE, Serial Quad I/O, SMART-I.S., SQI, SuperSwitcher, SuperSwitcher II, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. © 2017, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. © 2017 Microchip Technology Inc. Product Brief DS40001894B-page 16 PIC16(L)F184XX ISBN: 978-1-5224-2115-3 Quality Management System Certified by DNV ISO/TS 16949 Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California ® ® and India. The Company’s quality system processes and procedures are for its PIC MCUs and dsPIC ® DSCs, KEELOQ code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. © 2017 Microchip Technology Inc. Product Brief DS40001894B-page 17 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Austin, TX Tel: 512-257-3370 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Novi, MI Tel: 248-848-4000 Houston, TX Tel: 281-894-5983 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Tel: 317-536-2380 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Tel: 951-273-7800 Raleigh, NC Tel: 919-844-7510 New York, NY Tel: 631-435-6000 San Jose, CA Tel: 408-735-9110 Tel: 408-436-4270 Canada - Toronto Tel: 905-695-1980 Fax: 905-695-2078 Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2943-5100 Fax: 852-2401-3431 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 China - Dongguan Tel: 86-769-8702-9880 China - Guangzhou Tel: 86-20-8755-8029 China - Hangzhou Tel: 86-571-8792-8115 Fax: 86-571-8792-8116 China - Hong Kong SAR Tel: 852-2943-5100 Fax: 852-2401-3431 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 China - Shanghai Tel: 86-21-3326-8000 Fax: 86-21-3326-8021 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 China - Shenzhen Tel: 86-755-8864-2200 Fax: 86-755-8203-1760 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 India - Pune Tel: 91-20-3019-1500 Japan - Osaka Tel: 81-6-6152-7160 Fax: 81-6-6152-9310 Japan - Tokyo Tel: 81-3-6880- 3770 Fax: 81-3-6880-3771 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 Taiwan - Kaohsiung Tel: 886-7-213-7830 Taiwan - Taipei Tel: 886-2-2508-8600 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 Finland - Espoo Tel: 358-9-4520-820 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 France - Saint Cloud Tel: 33-1-30-60-70-00 Germany - Garching Tel: 49-8931-9700 Germany - Haan Tel: 49-2129-3766400 Germany - Heilbronn Tel: 49-7131-67-3636 Germany - Karlsruhe Tel: 49-721-625370 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Germany - Rosenheim Tel: 49-8031-354-560 Israel - Ra’anana Tel: 972-9-744-7705 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Italy - Padova Tel: 39-049-7625286 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Norway - Trondheim Tel: 47-7289-7561 Poland - Warsaw Tel: 48-22-3325737 Romania - Bucharest Tel: 40-21-407-87-50 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 Sweden - Gothenberg Tel: 46-31-704-60-40 Sweden - Stockholm Tel: 46-8-5090-4654 UK - Wokingham Tel: 44-118-921-5800 Fax: 44-118-921-5820 © 2017 Microchip Technology Inc. Product Brief DS40001894B-page 18