PL502-00DC

PL502-00 Multiplier VCXO IC Die for 12 to 25MHz Parallel Resonant Crys tals      XIN 27 XOUT 29 VDD S0V S1V S2V  65 mil VDD Integrated voltage-controlled crystal oscillator circuitry (VCXO) (pull range 500ppm minimum). Low phase noise (-125dBc @ 10kHz offset and 155.52MHz output) Selectable frequency multipliers (x1, x2, x4, x8). 3.3V supply voltage. Uses inexpensive fundamental-mode parallel resonant crystals (from 12 to 25MHz). Selectable High Drive (30mA) or Standard Drive (10mA) output. Available in DIE (65 mil x 62 mil). OE^  DIE CONFIGURATION 62 mil FEATURES 25 23 21 20 19 18 (1550,1475) Die ID: 3737-37 13 CLK 10 GND C502B DESCRIPTION BLOCK DIAGRAM XIN VCXO Selectable PLL VCON CLK 31 7 (0,0) GND The PL502-00 is a monolithic low jitter and low phase noise (-125dBc @10kHz offset and 155.52MHz output), high performance CMOS VCXO IC Die, that uses a low cost crystal (12-25MHz). The same die can be used as a VCXO with output frequencies ranging from F XIN x 1 to F XIN x 8 using selector pad bonding options (see Multiplier Selection Table on this page). This makes the PL502-00 ideal for a wide range of applications from 12MHz to 190MHz (including 27MHz, 35.328MHz, 77.76MHz and 155.52MHz, etc.). VCON Y Note: X ^ denotes internal pull up V denotes internal pull down MULTIPLIER SELECTION SELECTION S2 S1 S0 0 0 0 0 0 1 0 1 0 0 1 1 1 0 0 1 1 1 0 1 1 F XIN CLK (MHz) 12MHz – 25MHz 1 0 1 F XIN x 2 F XIN x 4 F XIN x 1 F XIN x 2* F XIN x 8 F XIN x 1* F XIN x 4* F XIN x 8* Note: - Selector pads default to ‘0’, wire bond to VDD to set to ‘1’ - (*) High-drive output PAD DESCRIPTION DIE SPECIFICATIONS Name Number Description XIN 27 Crystal input connection. XOUT 29 Crystal output connection. VCON 31 Voltage Control Input. GND 7,10 Name Value CLK 13 Size Reverse side Pad dimensions Thickness 65 x 62 m il GND 80 m icron x 80 micron 8 m il S[0:2] 18,19,20 VDD 21,23 OE 25 Ground. Clock Output. Frequency selection pads 3.3V Power Supply. Output Enable: ‘0’ to disable (tri-state output), ‘1’ (default value when not connected) to enabled the output. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474-1000 • www.micrel.com Rev 4/27/11 Page 1 PL502-00 Multiplier VCXO IC Die for 12 to 25MHz Parallel Resonant Crys tals ELECTRICAL SPECIFICATIONS 1. Absolute Maximum Ratings PARAMETERS SYMBOL MIN. MAX. UNITS V V V Supply Voltage Input Voltage, dc VDD VI -0.5 4.6 VDD +0.5 Output Voltage, dc Storage Temperature VO TS -0.5 -65 VDD +0.5 150 Ambient Operating Temperature* Junction Temperature Lead Temperature (soldering, 10s) TA TJ -40 85 125 260 ESD Protection, Human Body Model 2 C C C C kV Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods may cause permane nt damage to the device and affect product reliability. These conditions represent a stress rating only, and functional operations of the dev ice at these or any other conditions above the operational limits noted in this specification is not implied. * Note: Operating Temperature is guaranteed by design for all parts (COMMERCIAL and INDUSTRIAL), but tested for COMMERCIAL grade only. 2. DC Electrical Specifications PARAMETERS Supply Current, Dynam ic, with Loaded Outputs Operating Voltage Output drive current (High Drive) Output drive current (Standard Drive) VCXO Control Voltage SYMBOL IDD VDD I OH I OL I OH I OL VCON CONDITIONS MIN. TYP. F XIN = 12 - 25MHz Output load of 10pF VOH = VDD -0.4V, V DD =3.3V VOL = 0.4V, V DD = 3.3V VOH = VDD -0.4V, V DD =3.3V VOL = 0.4V, V DD = 3.3V 2.97 30 30 10 10 0 MAX. UNITS 35 mA 3.63 V mA mA mA 3.3 mA V MAX. UNITS 25 MHz 3. AC Electrical Specifications PARAMETERS Input Crystal Frequency Output Clock Rise/Fall Time (Standard Drive) Output Clock Rise/Fall Time (High Drive) Output Clock Duty Cycle SYMBOL CONDITIONS MIN. TYP. 12 0.3V ~ 3.0V with 15 pF load 3.0 0.3V ~ 3.0V with 15 pF load 1.2 Measured @ 50% V DD 45 50 ns 55 % Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474-1000 • www.micrel.com Rev 11/29/11 Page 2 PL502-00 Multiplier VCXO IC Die for 12 to 25MHz Parallel Resonant Crys tals 4. Voltage Control Crystal Oscillator PARAMETERS VCXO Stabilization Time * SYMBOL T VC XOS TB VCXO Tuning Range CLK output pullability VCXO Tuning Characteristic Pull range linearity VCON pin input impedance VCON modulation BW CONDITIONS From power valid F XIN = 12 – 25MHz; XTAL C 0/C 1 < 250 0V  VCON  3.3V VCON=1.65V, 1.65V MIN. TYP. MAX. UNITS 10 ms 500 ppm 150 ppm ppm/V % 200 10 0V  VCON  3.3V, -3dB 2000 10 k kHz Note: Parameters denoted with an asterisk (*) represent nominal characterization data and are not production tested to any specific limits. 5. Crystal Specifications PARAMETERS Crystal Resonator Frequency Crystal Loading Rating Crystal Pullability Recommended ESR SYMBOL CONDITIONS MIN. F XIN Parallel Fundamental Mode 12 C L (xtal) C 0/C 1 (xtal) RE At VCON = 1.65V AT cut AT cut TYP. MAX. UNITS 25 MHz 9.5 250 30 pF  Note: Crystal Loading rating: 9.5pF is the loading the crystal sees from the VCXO chip at VCON = 1.65V. It is assumed that the crystal will be at nominal frequency at this load. If the crystal requires more load to be at nominal frequency, the additional load must be add ed external ly. This however may reduce the pull range. 6. Jitter and Phase Noise specification* PARAMETERS RMS Period Jitter (1 sigma – 1000 samples) Phase Noise relative to carrier Carrier Frequency 44MHz Phase Noise relative to carrier Carrier Frequency 155.52MHz CONDITIONS at 155MHz, with capacitive decoupling between VDD and GND. @100Hz offset @1kHz offset @10kHz offset @100kHz offset @1MHz offset @100Hz offset @1kHz offset @10kHz offset @100kHz offset @1MHz offset @10MHz offset @40MHz offset MIN. TYP. MAX. UNITS 20 ps -113 -130 -135 -128 -128 -100 -115 -125 -116 -114 -132 -142 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz * General condition: Control Voltage is 0V. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474-1000 • www.micrel.com Rev 11/29/11 Page 3 PL502-00 Multiplier VCXO IC Die for 12 to 25MHz Parallel Resonant Crys tals PAD ASSIGNMENT Pad # Name X (m) Y (m) Description 7 10 13 GND GND CLK 1042 1400 1400 109 259 716 Ground. Ground. CMOS Clock Output. 18 S2 1232 1365 Used to select multiplication factor and Standard or High -Drive output. Internal pull down. 19 S1 1042 1365 Used to select multiplication factor and Standard or High -Drive output. Internal pull down. 20 S0 854 1365 Used to select multiplication factor and Standard or High -Drive output. Internal pull down. 21 23 VDD VDD 659 459 1365 1365 3.3V Power Supply. 3.3V Power Supply. 25 27 29 OE XIN XOUT 194 109 109 1365 1017 646 Used to Enable/Disable the output. Internal pull up. See Crystal input. See Crystal Specifications on page 3. Crystal output. See Crystal Specifications on page 3. 31 VCON 109 181 Voltage Control Input. 0V to 3.3V. ORDERING INFORMATION For part ordering, please contact our Sales Department: 2180 Fortune Drive, San Jose, CA 95131, USA Tel: (408) 944-0800 Fax: (408) 474-1000 PART NUMBER The order number for this device is a combination of the following: Device number, Package type and Operating temperature range PL502-00 D C TEMPERATURE C=COMMERCIAL I=INDUSTRAL PART NUMBER Order Number Marking PL502-00DC N/A PACKAGE TYPE D=DIE W=SAW WAFER IN BLUE TAPE Package Option Die (Waffle Pack) . Micrel Inc., reserves the right to make changes in its products or specifications, or both at any time without notice. The in formation furnished by Micrel is believed to be accurate and reliable. However, Micrel makes no guarantee or warranty concerning the accuracy of said information and shall not be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon this product. LIFE SUPPORT POLICY: Micrel’s products are not authorized for use as critical components in life support devices or systems without the express written approval of the President of Micrel Inc. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474-1000 • www.micrel.com Rev 11/29/11 Page 4