SG117A/SG117
1.5A Three Terminal Adjustable Voltage Regulator
Description
Features
The SG117 and SG117A are 3-terminal positive
adjustable voltage regulators which offer improved
performance over the original 117 design. A major
feature of the SG117A is a reference voltage tolerance
guaranteed within ± 1%, allowing an overall power
supply tolerance to be better than 3% using
inexpensive 1% resistors. Line and load regulation
performance has been improved as well.
Adjustable Output Down to 1.25V
1% Output Voltage Tolerance
0.01%/V Line Regulation
0.3% Load Regulation
Min. 1.5A Output Current
Typical 80dB Ripple Rejection
Available in Hermetic TO-257
Moreover, the SG117A reference voltage is guaranteed
not to exceed 2% when operating over the full load, line
and power dissipation conditions.
The SG117A
adjustable regulators offer an improved solution for all
positive voltage regulator requirements with load
currents up to 1.5A.
High Reliability Features –
SG117A/SG117
In addition to replacing many fixed regulators, the
SG117/A can be used in a variety of other applications
due to its ‘floating’ design as long as the input-to-output
differential maximum is not exceeded, such as a
current source. A higher voltage version is available
the SG117AHV and SG117HV which offers input
voltage up to 60V.
Available to MIL-STD-883, ¶1.2.1
MSC-AMS level "S" Processing Available
Available to DSCC
– Standard Microcircuit Drawing (SMD)
MIL-M-38510/7703405XA SG117AT-JAN
MIL-M-38510/7703405YA SG117AK-JAN
Schematic Diagram
Figure 1 · Block Diagram
January 2015 Rev. 1.4
www.microsemi.com
© 2015 Microsemi Corporation- Analog Mixed Signal
1
1.5A 3-Terminal Adjustable Voltage Regulator
Connection Diagrams and Ordering Information
Ambient
Temperature
Type
Package
Part Number
Packaging
Type
Connection Diagram
SG117AK
SG117AK-883B
ADJUSTMENT
SG117AK-DESC
-55°C to
125°C
K
3-TERMINAL
METAL CAN
1
SG117K
TO-3
2
SG117K-883B
VIN
SG117K-DESC
SG117K-JAN
SG117AT
SG117AT-883B
SG117AT-DESC
-55°C to
125°C
T
3-TERMINAL
METAL CAN
SG117T
VIN
TO-39
ADJUST
SG117T-883B
1
2
3
VOUT
SG117T-DESC
SG117T-JAN
SG117AIG
-55°C to
125°C
IG
SG117AIG-883B
3-Pin
HERMETIC
SG117AIG-DESC
Package
(Isolated)
SG117IG
VIN
TO-257
VOUT
ADJUST
Case is Isolated
SG117IG-883B
SG117IG-DESC
SG117AG
SG117AG-883B
-55°C to
125°C
G
VIN
3-Pin
HERMETIC
SG117AG-DESC
Package
SG117G
TO-257
SG117G-883B
SG117G-DESC
2
VOUT
ADJUST
Case is VOUT
Connection Diagrams and Ordering Information
Connection Diagrams and Ordering Information
Ambient
Temperature
Type
Package
Part Number
Packaging
Type
Connection Diagram
SG117AL
SG117AL-883B
-55°C to
125°C
L
20-Pin
Ceramic
SG117AL-DESC
SG117L
CLCC
SG117L-883B
SG117L-DESC
Notes:
1. Contact factory for JAN and DESC part availability.
2. All parts are viewed from the top.
3. For devices with multiple inputs and outputs both must be externally connected together at the device terminals.
4. For normal operation, the SENSE pin must be externally connected to the load.
5. These Hermetic Packages use Sn63/Pb37 hot solder dip lead finish, contact factory for availability of RoHS versions.
3
1.5A 3-Terminal Adjustable Voltage Regulator
Absolute Maximum Ratings
Parameter
Power Dissipation
Input to Output Voltage Differential
Storage Temperature Range
Maximum Operating Junction Temperature
Value
Units
Internally Limited
40
V
-65 to 150
°C
150
°C
Lead Temperature (Soldering, 10 seconds)
300
°C
Notes:
Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into,
negative out of specified terminal.
Thermal Data
Value
Units
Thermal Resistance-Junction to Case, θJC
3
°C/W
Thermal Resistance-Junction to Ambient, θJA
35
°C/W
Thermal Resistance-Junction to Case, θJC
15
°C/W
Thermal Resistance-Junction to Ambient, θJA
120
°C/W
Thermal Resistance-Junction to Case, θJC
3.5
°C/W
Thermal Resistance-Junction to Ambient, θJA
42
°C/W
Thermal Resistance-Junction to Case, θJC
3.5
°C/W
Thermal Resistance-Junction to Ambient, θJA
42
°C/W
35
°C/W
Parameter
K Package: 3 Terminal TO-3 Metal Can
T Package: 3-Pin TO-39 Metal Can
IG Package: 3-Pin TO-257 Hermetic (Isolated)
G Package: 3-Pin TO-257 Hermetic
L Package: 20-Pin Ceramic (LCC) Leadless
Thermal Resistance-Junction to Case, θJC
°C/W
Thermal Resistance-Junction to Ambient, θJA
120
Notes:
1. Junction Temperature Calculation: TJ = TA + (PD x θJA).
2. The above numbers for θJC are maximums for the limiting thermal resistance of the package in a standard mounting
configuration. The θJA numbers are meant to be guidelines for the thermal performance of the device/pcboard system. All of
the above assume no ambient airflow.
Recommended Operating Conditions
Parameter
Input Voltage Range
Value
Units
VOUT +3.5V to 37
V
-55 to 125
°C
Operating Ambient Temperature Range
SG117A / SG117
Note: Range over which the device is functional.
4
Electrical Characteristics
Electrical Characteristics
Unless otherwise specified, these characteristics apply over the full operating ambient temperature for the
SG117A / SG117 with -55°C < TA < 125°C, VIN – VOUT = 5.0V and for IOUT = 500mA (K, G, and IG) and IOUT =
100mA (T, and L packages). Although power dissipation is internally limited, these specifications are
applicable for power dissipations of 2W for the T, and L packages, and 20W for the K, G, and IG packages.
IMAX is 1.5A for the K, G, and IG packages and 500mA for the T, and L packages. Low duty cycle pulse
testing techniques are used which maintains junction and case temperatures equal to the ambient
temperature.
SG117A
Parameter
SG117
Test Condition
Units
Min
Typ
Max
Min
Typ
Max
1.20
1.25
1.30
Reference Section
Reference Voltage
IOUT = 10mA, TA = 25°C
3V ≤ (VIN – VOUT ) ≤ 40V,
P ≤ PMAX
10mA ≤ IOUT ≤ IMAX
1.238
1.250 1.262
1.225
1.250 1.270
V
Output Section
Line Regulation¹
3V ≤ (VIN – VOUT) ≤ 40V,
IL = 10mA
TA = 25°C
0.005
0.01
0.01
0.02
TA = TMIN to TMAX
0.01
0.02
0.02
0.05
%/V
10mA ≤ IOUT ≤ IMAX
Load Regulation¹
VOUT ≤ 5V, TA = 25°C
5
15
5
15
mV
VOUT > 5V, TA = 25°C
0.1
0.3
0.1
0.3
%
VOUT ≤ 5V
20
50
20
50
mV
VOUT > 5V
0.3
1
0.3
1
%
0.002
0.02
0.03
0.07
%/W
Thermal Regulation²
TA = 25°C, 20ms pulse
Ripple Rejection
VOUT = 10V, f = 120Hz
CADJ = 1µF, TA = 25°C
CADJ = 10µF
Minimum Load Current
(VIN – VOUT) = 40V
Current Limit
(VIN – VOUT) ≤ 15V
65
66
65
80
3.5
66
5
dB
80
3.5
K, P, G, IG Packages
1.5
2.2
1.5
2.2
T, L Packages
0.5
0.8
0.5
0.8
K, P, G, IG Packages
0.3
0.4
0.3
0.4
T, L Packages
0.15
0.2
0.15
0.2
5
mA
A
(VIN – VOUT) = 40V, TJ = 25°C
Temperature Stability²
Long Term Stability²
RMS Output Noise (% of
VOUT)²
Adjust Section
Adjust Pin Current
TA = 125°C, 1000 Hours
TA = 25°C, 10Hz ≤ f ≤ 10kHz
1
2
1
0.3
1
0.3
0.001
50
A
1
%
0.001
100
50
100
µA
10mA < IOUT < IMAX,
0.2
5
0.2
5
2.5V < (VIN – VOUT) < 40V
¹Regulation is measured at constant junction temperature, using pulse testing with low duty cycle. Changes in output voltage
due to heating effects are covered under the specification for thermal regulation.
²These parameters, although guaranteed, are not tested in production.
Adjust Pin Current
Change
5
1.5A 3-Terminal Adjustable Voltage Regulator
Characteristic Curves
6
Figure 2 · Output Voltage Deviation vs. Temperature
Figure 3 · Output Current vs. Input / Output Differential
Figure 4 · Adjust Current vs. Temperature
Figure 5 · Input / Output Differential vs. Temperature
Figure 6 · Reference Voltage vs. Temperature
Figure 7 · Quiescent Current vs. Input /Output
Differential
Characteristic Curves
Characteristic Curves
Figure 8 · Ripple Rejection vs. Output Voltage
Figure 10 · Ripple Rejection vs. Output Current
Figure 12 · Line Transient Response
Figure 9 · Ripple Rejection vs. Frequency
Figure 11 · Output Impedance vs. Frequency
Figure 13 · Load Transient Response
7
1.5A 3-Terminal Adjustable Voltage Regulator
Characteristic Curves
Figure 14 · Output Impedance vs. Frequency
Figure 15 · Line Transient Response
Figure 16 · Load Transient Response
8
Application Information
Application Information
General
The SG117A develops a 1.25V reference voltage between the output (OUT) and the adjust (ADJ) terminals (see
Basic Regulator Circuit). By placing a resistor, R1 between these two terminals, a constant current is caused to flow
through R1 and down through R2 to set the overall output voltage. Normally this current is the specified minimum load
current of 5mA or 10mA. It is important to maintain this minimum output load current requirement otherwise the
device may fail to regulate, and the output voltage may rise.
VOUT VREF
1
I ADJ R 2
R1
R2
Figure 17 · Basic Regulator Circuit
The IADJ current does add an error to the output divider ratio, however because I ADJ is very small and constant
when compared with the current through R1, it represents a small error and can often be ignored.
It is easily seen from the above equation, that even if the resistors were of exact value, the accuracy of the output
is limited by the accuracy of VREF. With a guaranteed 1% reference, a 5V power supply design, using ±2% resistors,
would have a worse case manufacturing tolerance of ± 4%. If 1% resistors were used, the tolerance would drop to ±
2.5%. A plot of the worst case output voltage tolerance as a function of resistor tolerance is shown below.
Figure 18 · Voltage Tolerance vs. Resistor Tolerance
Bypass Capacitors
Input bypassing using a 0.1 μF ceramic or 1μF solid tantalum is recommended, and especially when any input filter
capacitors are more than 5 inches from the device. A 0.1µF bypass capacitor on the ADJ pin is required if the load
current varies by more than 1A/µsec. Improved ripple rejection (80dB) can be accomplished by adding a 10μF
capacitor from the ADJ pin to ground.
Figure 19 · Improving Ripple Rejection
9
1.5A 3-Terminal Adjustable Voltage Regulator
While the SG117 is stable with no output capacitor, for improved AC transient response and to prevent the
possibility of oscillation due to an unknown reactive load, a 1μF capacitor is also recommended at the output.
Because of their low impedance at high frequencies, the best type of capacitor to use is solid tantalum; ceramic
capacitors may also be used. When bypass capacitors are used, it may be necessary to provide external protection
diodes to prevent this external large capacitance from discharging through internal low current paths, which may
damage the device. Although the duration of any surge current is short, there may be sufficient energy to damage
the regulator. This is particularly true of the large capacitance on the ADJ pin when output voltages are higher than
25V. Such a capacitor could discharge into the ADJ pin when either the input or output is shorted. See figure below.
D1 1N4002
SG117A
IN
VOUT
OUT
ADJ
R1
C1
D2
1N4002
1 µF
R2
Note: D1 protects against C1
D2 protects against C2
C2
10µF
Figure 20 · Use of Protection Diodes
Load Regulation
Because the SG117A is a three-terminal device, it is not possible to provide true remote load sensing. Load
regulation will be limited by the resistance of the wire connecting the regulator to the load. From the data sheet
specification, regulation is measured at the bottom of the package. Negative side sensing is a true Kelvin connection,
with the bottom of the output divider returned to the negative side of the load. Although it may not be immediately
obvious, best load regulation is obtained when the top of the divider is connected directly to the case, not to the load.
This is illustrated in (Connections for Best Load Regulation). If R1 were connected to the load, the effective
resistance between the regulator and the load would be:
R 2 R1
R , R P
1
RP
ParasiticLineResistance
Connected as shown, RP is not multiplied by the divider ratio. RP is about 0.004Ω per foot using 16 gauge wire.
This translates to 4mV/ft. at 1A load current, so it is important to keep the positive lead between regulator and load as
short as possible.
Figure 21 · Connections for Best Load Regulation
10
Application Information
Current Limit
As outlined in the Electrical Characteristics the current limit will activate whenever the output current exceeds the
specified levels. It is also important to bear in mind that the regulator includes a foldback-current characteristic that
limits the current at higher VIN to VOUT differential voltages. This power limiting characteristic will prevent the regulator
from providing full output current depending on the V IN to V= differential. Also if during a short circuit situation the
regulator was presented with a voltage that exceeds the Absolute Maximum Rating of 40V (e.g. VIN > 40V, VOUT = 0V)
the device may fail, or be permanently damaged.
Typical Applications
Figure 22 · 1.2V – 25V Adjustable Regulator
Figure 23 · 5V Regulator with Shut Down
SG117A
IN
IOUT = VREF/R1*
OUT
R1
ADJ
* 0.8Ω ≤ R1 ≤ 120Ω
Figure 24 ·
Figure 25 · Programmable Current Limiter
11
1.5A 3-Terminal Adjustable Voltage Regulator
PACKAGE OUTLINE DIMENSIONS
Controlling dimensions are in inches, metric equivalents are shown for general information.
Dim
D
D1
Q
A
D
D1
A
e
F
b
L1
e1
L
α
k
k1
b1
MILLIMETERS
MIN
MAX
8.89
8.13
4.19
9.40
8.51
4.70
INCHES
MIN
MAX
0.350
0.320
0.165
0.370
0.335
0.185
b
F
e
0.41
0.48
1.02
5.08 BSC
0.016
0.019
0.040
0.200 BSC
k
k1
L
0.71
0.74
12.70
0.028
0.029
0.500
α
e1
b1
Q
L1
45° TYP
2.54 TYP
0.41
0.53
90° TYP
1.27
0.86
1.14
14.48
0.034
0.045
0.570
45° TYP
0.100 TYP
0.016
0.021
90° TYP
0.50
Figure 26 · T 3-Pin Metal Can TO-39 Package Dimensions
E3
D
Dim
E
A
A1
L2
L
8
3
MILLIMETERS
MIN
13
MAX
D/E
E3
e
8.64
9.14
8.128
1.270 BSC
0.340
0.360
0.320
0.050 BSC
B1
L
A
0.635 TYP
1.02
1.52
1.626
2.286
0.025 TYP
0.040
0.060
0.064
0.090
h
A1
A2
1.016 TYP
1.372
1.68
1.168
0.040 TYP
0.054
0.066
0.046
L2
B3
1.91
2.41
0.203R
0.075
0.95
0.008R
1. All exposed metalized area shall be gold plated 60
micro-inch minimum thickness over nickel plated unless
otherwise specified in purchase order.
h
18
B1
e
B3
Figure 27 · L 20-Pin Ceramic Leadless Chip Carrier (LCC) Package Dimensions
12
INCHES
MIN
Note:
1
A2
MAX
PACKAGE OUTLINE DIMENSIONS
PACKAGE OUTLINE DIMENSIONS
Dim
E
A
V
P
A1
Z
D
O
D1
J
H
L
b
e
A2
MILLIMETERS
MIN
MAX
INCHES
MIN
MAX
A
A1
A2
4.70
0.89
2.92
5.21
1.14
3.18
0.185
0.035
0.115
0.205
0.045
0.125
b
D
D1*
0.71
16.38
10.41
.081
16.76
10.92
0.027
0.645
0.410
0.032
0.660
0.430
e
E*
H
2.54 BSC
10.41
10.67
0.50
0.100 BSC
0.410
0.420
0.020
L
O
P
J
V
Z
12.70
13.39
3.56
0.500
0.527
0.140
13.64
3.81
0.10
5.13
5.38
1.40 TYP
0.537
0.150
0.004
0.202
0.212
0.055 TYP
*Excludes Weld Fillet Around Lid.
Figure 28 · G/IG 3-Pin Hermetic TO-257 Package Dimensions
D
A
Dim
F
b
L
q
S
R
R1
e
e1
MILLIMETERS
MIN
MAX
INCHES
MIN
MAX
A
q
b
6.86
29.90
0.97
7.62
30.40
1.09
0.270
1.177
0.038
0.300
1.197
0.043
D
S
e
19.43
16.64
10.67
19.68
17.14
11.18
0.765
0.655
0.420
0.775
0.675
0.440
E1
F
R1
5.21
1.52
3.84
5.72
2.03
4.09
0.205
0.060
0.151
0.225
0.080
0.161
L
R
10.79
12.57
12.19
13.34
0.425
0.495
0.480
0.525
Figure 29 · K 3-Pin TO-3 Package Dimensions
13
Microsemi Corporation (Nasdaq: MSCC) offers a comprehensive portfolio of semiconductor
and system solutions for communications, defense & security, aerospace and industrial
markets. Products include high-performance and radiation-hardened analog mixed-signal
integrated circuits, FPGAs, SoCs and ASICs; power management products; timing and
synchronization devices and precise time solutions, setting the world’s standard for time; voice
processing devices; RF solutions; discrete components; security technologies and scalable
anti-tamper products; Power-over-Ethernet ICs and midspans; as well as custom design
capabilities and services. Microsemi is headquartered in Aliso Viejo, Calif., and has
approximately 3,400 employees globally. Learn more at www.microsemi.com.
Microsemi Corporate Headquarters
One Enterprise, Aliso Viejo,
CA 92656 USA
Within the USA: +1 (800) 713-4113
Outside the USA: +1 (949) 380-6100
Sales: +1 (949) 380-6136
Fax: +1 (949) 215-4996
E-mail: sales.support@microsemi.com
© 2015 Microsemi Corporation. All
rights reserved. Microsemi and the
Microsemi logo are trademarks of
Microsemi Corporation. All other
trademarks and service marks are the
property of their respective owners.
Microsemi makes no warranty, representation, or guarantee regarding the information contained herein or
the suitability of its products and services for any particular purpose, nor does Microsemi assume any
liability whatsoever arising out of the application or use of any product or circuit. The products sold
hereunder and any other products sold by Microsemi have been subject to limited testing and should not
be used in conjunction with mission-critical equipment or applications. Any performance specifications are
believed to be reliable but are not verified, and Buyer must conduct and complete all performance and
other testing of the products, alone and together with, or installed in, any end-products. Buyer shall not
rely on any data and performance specifications or parameters provided by Microsemi. It is the Buyer’s
responsibility to independently determine suitability of any products and to test and verify the same. The
information provided by Microsemi hereunder is provided “as is, where is” and with all faults, and the
entire risk associated with such information is entirely with the Buyer. Microsemi does not grant, explicitly
or implicitly, to any party any patent rights, licenses, or any other IP rights, whether with regard to such
information itself or anything described by such information. Information provided in this document is
proprietary to Microsemi, and Microsemi reserves the right to make any changes to the information in this
document or to any products and services at any time without notice.
SG117 1.4/01.15
工商网监
湘ICP备2023018690号
