SY100E154JZTR

SY10E154 SY100E154 SY10E154 5-BIT 2:1 MUX-LATCH Micrel, Inc. FEATURES SY100E154 DESCRIPTION ■ ■ ■ ■ ■ ■ ■ 750ps max. LEN to output Extended 100E VEE range of –4.2V to –5.5V 700ps max. D to output Differential outputs Asynchronous Master Reset Dual latch-enables Fully compatible with industry standard 10KH, 100K ECL levels ■ Internal 75KΩ input pulldown resistors ■ Fully compatible with Motorola MC10E/100E154 ■ Available in 28-pin PLCC package The SY10/100E154 offer five 2:1 multiplexers followed by latches with differential outputs, designed for use in new, high-performance ECL systems. The two external Latch-Enable signals (LEN1, LEN2) are gated through a logical OR operation before use as control for the five latches. When both LEN1 and LEN2 are at a logic LOW, the latches are transparent, thus presenting the data from the multiplexers at the output pins. If either LEN1 or LEN2 (or both) are at a logic HIGH, the outputs are latched. The multiplexer operation is controlled by the SEL(Select) signal which selects one of the two bits of input data at each mux to be passed through. The MR (Master Reset) signal operates asynchronously to make all Q outputs go to a logic LOW. PIN NAMES BLOCK DIAGRAM Pin D0a D0b SEL D1a MUX D1b SEL D2a MUX D2b SEL D3a MUX D3b SEL D4a MUX D4b Q Q0 D0a–D4a Input Data a E Q NR Q0 D0b–D4b Input Data b SEL Data Select Input D Q Q1 LEN1, LEN2 Latch Enables E Q NR MR Master Reset Q1 Q0–Q4 True Outputs Q0–Q4 Inverted Outputs D Q Q2 VCCO VCC to Output E Q NR Q2 D Q Q3 E Q NR Q3 D Q Q4 E Q N R Q4 D MUX SEL Function SEL LEN1 LEN2 MR M9999-032006 hbwhelp@micrel.com or (408) 955-1690 Rev.: E 1 Amendment: /0 Issue Date: March 2006 SY10E154 SY100E154 Micrell, Inc. Ordering Information(1) Q4 Q4 VCCO D3b D3a D4b D4a PACKAGE/ORDERING INFORMATION Part Number Package Type Operating Range Package Marking Lead Finish Q3 SY10E154JC J28-1 Commercial SY10E154JC Sn-Pb J28-1 Commercial SY10E154JC Sn-Pb SY100E154JC J28-1 Commercial SY100E154JC Sn-Pb 15 Q3 VCC Q2 SY10E154JCTR(2) 14 Q2 SY100E154JCTR(2) J28-1 Commercial SY100E154JC Sn-Pb SY10E154JZ(3) J28-1 Commercial SY10E154JZ with Pb-Free bar-line indicator Matte-Sn SY10E154JZTR(2, 3) J28-1 Commercial SY10E154JZ with Pb-Free bar-line indicator Matte-Sn SY100E154JZ(3) J28-1 Commercial SY100E154JZ with Pb-Free bar-line indicator Matte-Sn SY100E154JZTR(2, 3) J28-1 Commercial SY100E154JZ with Pb-Free bar-line indicator Matte-Sn 25 24 23 22 21 20 19 SEL 26 18 LEN1 LEN2 27 17 28 16 VEE 1 MR 2 PLCC TOP VIEW J28-1 D0a 3 13 Q1 D0b 4 12 Q1 9 10 11 Q0 8 VCCO Q0 7 D2a D2b 6 D1a D1b 5 28-Pin PLCC (J28-1) Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC Electricals only. 2. Tape and Reel. 3. Pb-Free package is recommended for new designs. M9999-032006 hbwhelp@micrel.com or (408) 955-1690 2 SY10E154 SY100E154 Micrel, Inc. TRUTH TABLES SEL Data LEN1 LEN2 Latch H a L L Transparent L b H X Latched X H Latched DC ELECTRICAL CHARACTERISTICS VEE = VEE (Min.) to VEE (Max.); VCC = VCCO = GND TA = 0°C Symbol Parameter TA = +25°C Min. Typ. Max. Min. Typ. IIH Input HIGH Current IEE Power Supply Current 10E 100E TA = +85°C Max. Min. Typ. Max. Unit Condition µA — mA — Unit Condition ps — ps — ps — — — 150 — — 150 — — 150 — — 76 76 91 91 — — 76 76 91 91 — — 76 87 91 105 AC ELECTRICAL CHARACTERISTICS VEE = VEE (Min.) to VEE (Max.); VCC = VCCO = GND TA = 0°C Symbol TA = +85°C Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Propagation Delay to Output D SEL LEN MR 325 475 350 450 500 650 500 600 700 925 750 800 325 475 350 450 500 650 500 600 700 925 750 800 325 475 350 450 500 650 500 600 700 925 750 800 Set-up Time D SEL 300 500 100 250 — — 300 500 100 250 — — 300 500 100 250 — — Hold Time D SEL 300 200 –100 –250 — — 300 200 –100 –250 — — 300 200 –100 –250 — — tRR Reset Recovery Time 800 600 — 800 600 — 800 600 — ps — tPW Minimum Pulse Width, MR 400 — — 400 — — 400 — — ps — tskew Within-Device Skew — 50 — — 50 — — 50 — ps 1 tr tf Rise/Fall Time 20% to 80% 300 475 800 300 475 800 300 475 800 ps — tPD tS tH Parameter TA = +25°C Note: 1. Within-device skew is defined as identical transitions on similar paths through a device. M9999-032006 hbwhelp@micrel.com or (408) 955-1690 3 SY10E154 SY100E154 Micrell, Inc. 28-PIN PLCC (J28-1) Rev. 03 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB USA http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2006 Micrel, Incorporated. M9999-032006 hbwhelp@micrel.com or (408) 955-1690 4