SY10E116JITR

NOT RECOMMENDED FOR NEW DESIGNS SY10E116 SY100E116 QUINT DIFFERENTIAL LINE RECEIVER Micrel, Inc. FEATURES DESCRIPTION ■ 450ps max. Propagation Delay ■ Extended 100E VEE range of –4.2V to –5.5V The SY10/100E116 are quint differential line receivers designed for use in new, high-performance ECL systems. These devices have emitter-follower outputs and an internally generated reference supply (VBB) for singleended reception. Active current sources combined with Micrel’s ASSET™ technology provide the receivers with excellent common mode noise rejection. The receiver design features clamp circuitry to cause a defined output state if both the inverting and non-inverting inputs are left open; in this case the Q output goes LOW, while the Q output goes HIGH. If both inverting and non-inverting inputs are at equal potential, the receiver does not go to a defined state, but rather shares current in normal differential amplifier fashion, producing output voltage levels midway between HIGH and LOW. The VBB output is intended for use as a reference voltage for single-ended reception of ECL signals to that device only. When using V BB for this purpose, it is recommended that VBB is decoupled to VCC via a 0.01 µF capacitor. For higher bandwidth, please refer to the SY10/100E416 device. ■ VBB output for single-ended reception ■ Fully compatible with industry standard 10KH, 100K I/O levels ■ Internal 75KΩ input pulldown resistors ■ Fully compatible with Motorola MC10E/100E116 ■ Available in 28-pin PLCC package BLOCK DIAGRAM D0 Q0 D0 Q0 D1 Q1 D1 Q1 D2 Q2 D2 Q2 D3 Q3 D3 Q3 D4 Q4 D4 Q4 PIN NAMES Pin VBB M9999-032006 hbwhelp@micrel.com or (408) 955-1690 SY10E116 SY100E116 Function D0, D0-D4, D4 Differential Input Pairs Q0, Q0-Q4, Q4 Differential Output Pairs VBB Reference Voltage Output VCCO VCC to Output Rev.: H 1 Amendment: /0 Issue Date: March 2006 SY10E116 SY100E116 Micrel, Inc. Ordering Information(1) VCCO Q4 VCCO Q4 D4 D3 25 D4 PACKAGE/ORDERING INFORMATION 24 23 22 21 20 19 D3 26 18 D2 27 17 D2 VEE VBB 28 16 15 PLCC TOP VIEW J28-1 1 2 14 Q3 Part Number Package Type Operating Range Package Marking Lead Finish SY10E116JI J28-1 Industrial SY10E116JI Sn-Pb Q3 SY10E116JITR(2) J28-1 Industrial SY10E116JI Sn-Pb VCC SY100E116JI J28-1 Industrial SY100E116JI Sn-Pb Q2 Q2 SY100E116JITR(2) J28-1 Industrial SY100E116JI Sn-Pb J28-1 Commercial SY10E116JC Sn-Pb SY10E116JCTR(2) J28-1 Commercial SY10E116JC Sn-Pb SY100E116JC J28-1 Commercial SY100E116JC Sn-Pb SY100E116JCTR(2) J28-1 Commercial SY100E116JC Sn-Pb SY10E116JY(3) J28-1 Industrial SY10E116JY with Pb-Free bar-line indicator Matte-Sn SY10E116JYTR(2, 3) J28-1 Industrial SY10E116JY with Pb-Free bar-line indicator Matte-Sn SY100E116JY(3) J28-1 Industrial SY100E116JY with Pb-Free bar-line indicator Matte-Sn SY100E116JYTR(2, 3) J28-1 Industrial SY100E116JY with Pb-Free bar-line indicator Matte-Sn 7 8 9 10 11 Q1 6 VCCO 5 Q0 SY10E116JC Q1 Q0 VCCO 12 VCCO 13 4 D1 3 D0 D1 D0 28-Pin PLCC (J28-1) Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC Electricals only. 2. Tape and Reel. 3. Pb-Free package is recommended for new designs. M9999-032006 hbwhelp@micrel.com or (408) 955-1690 2 SY10E116 SY100E116 Micrel, Inc. LOGIC EQUATION Qn = Dn DC ELECTRICAL CHARACTERISTICS VEE = VEE(Min.) to VEE(Max.); VCC = VCCO = GND TA = –40°C Symbol VBB Parameter Output Reference Voltage 10E 100E TA = 0°C TA = +25°C TA = +85°C Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. –1.43 –1.43 — — –1.30 –1.26 –1.38 –1.38 — — –1.27 –1.26 –1.35 –1.38 — — –1.25 –1.26 –1.31 –1.38 — — –1.19 –1.26 Unit V µA IIH Input HIGH Current — — 200 — — 200 — — 200 — — 200 IEE Power Supply Current 10E 100E — — 29 29 35 35 — — 29 29 35 35 — — 29 29 35 35 — — 29 33 35 40 150 — — 150 — — 150 — — 150 — — mV –2.0 — –0.6 –2.0 — –0.6 –2.0 — –0.6 –2.0 — –0.6 V VPP (DC) VCMR Input Sensitivity(1) Common Mode Range (2) mA Notes: 1. VPP is the minimum differential input voltage required to assure full ECL levels are present at the outputs. 2. VCMR is referenced to the most positive side of the differential input signal. Normal operation is obtained when the "HIGH" input is within the VCMR range and the input swing is greater than VPP (min.) and