SY58020UMI

SY58020U 6GHz, 1:4 CML Fanout Buffer/Translator with Internal I/O Termination General Description The SY58020U is a 2.5V/3.3V precision, high-speed, fully differential 1:4 CML fanout buffer. Optimized to provide four identical output copies with less than 15ps of skew and 27fsRMS of typical additive phase jitter, the SY58020U can process clock signals as fast as 6GHz. The differential input includes Micrel’s unique, 3-pin input termination architecture that interfaces to differential LVPECL, LVDS, and CML signals (AC- or DC-coupled) as small as 100mV without any level-shifting or termination resistor networks in the signal path. For AC-coupled input interface applications, an on-board output reference voltage (VREF-AC) is provided to bias the VT pin. The outputs are optimized to drive 400mV typical swing into 50Ω loads, with extremely fast rise/fall times guaranteed to be less than 60ps. The SY58020U operates from a 2.5V ±5% supply or 3.3V ±10% supply and is guaranteed over the full industrial temperature range (–40°C to +85°C). For applications that require LVPECL outputs, consider the SY58021U or SY58022U 1:4 fanout buffer with 800mV and 400mV output swing, respectively. The SY58020U is part of Micrel’s high-speed, Precision Edge® product line. Datasheets and support documentation are available on Micrel’s web site at: www.micrel.com. Functional Block Diagram Features • Precision 1:4, 400mV CML fanout buffer • Guaranteed AC performance over temperature/voltage: − > 6GHz fMAX clock − < 60ps tr / tf times − < 250ps tpd − < 15ps max. skew • Low-jitter performance: − 27fsRMS typical additive phase jitter • Accepts an input signal as low as 100mV • Unique patented input termination and VT pin accepts DC-coupled and AC-coupled differential inputs: LVPECL, LVDS, and CML • 50Ω source terminated CML outputs • Power supply 2.5V ±5% and 3.3V ±10% • Industrial temperature range: –40°C to +85°C • Available in 16-pin (3mm x 3mm) QFN package Applications • • • • • All SONET and All GigE clock distribution Fibre Channel clock and data distribution Backplane distribution Data distribution: OC-48, OC-48+FEC, XAUI High-end, low skew, multiprocessor synchronous clock distribution Typical Performance United States Patent No. RE44,134 Precision Edge is a trademark of Micrel, Inc. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com October 27, 2014 Revision 5.0 tcghelp@micrel.com or (408) 955-1690 Micrel, Inc. SY58020U Ordering Information(1) Part Number Package Type Operating Range Package Marking Lead Finish SY58020UMG QFN-16 Industrial 020U with Pb-Free bar-line indicator Pb-Free NiPdAu SY58020UMG TR(2) QFN-16 Industrial 020U with Pb-Free bar-line indicator Pb-Free NiPdAu Note: 1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC electrical only. 2. Tape and Reel. Pin Configuration 16-Pin QFN (QFN-16) Pin Description Pin Function Pin Number Pin Name 1, 4 IN, /IN Differential Input: This input pair receives the signal to be buffered. Each pin of this pair internally terminates with 50Ω to the VT pin. Note that this input will default to an indeterminate state if left open. See “Input Interface Applications” section. 2 VT Input Termination Center-Tap: Each input terminates to this pin. The VT pin provides a center-tap for each input (IN, /IN) to the termination network for maximum interface flexibility. See “Input Interface Applications” section. 3 VREF-AC 8, 13 VCC Positive Power Supply: Bypass with 0.1µF//0.01µF low ESR capacitors as close to the pins as possible. 5, 16 GND, Exposed Pad Ground. Exposed pad must be connected to a ground plane that is the same potential as the ground pin. 14, 15 11, 12 9, 10 6, 7 /Q0, Q0, /Q1, Q1, /Q2, Q2, /Q3, Q3 October 27, 2014 Reference Output Voltage: This output biases to VCC-1.2V. It is used when AC-coupling to differential inputs. Connect VREF-AC directly to the VT pin. Bypass with 0.01µF low ESR capacitor to VCC. See “Input Interface Applications” section. CML Differential Output Pairs: Differential buffered output copy of the input signal. The output swing is typically 400mV into 50Ω load. Normally terminate CML output pairs with 100Ω across Q and /Q outputs at the receiving end. Unused output pairs may be left floating with no impact on jitter or skew. See “CML Output Termination” section. 2 Revision 5.0 tcghelp@micrel.com or (408) 955-1690 Micrel, Inc. SY58020U Absolute Maximum Ratings(3) Operating Ratings(4) Power Supply Voltage (VCC).......................... -0.5V to +4.0V Input Voltage (VIN). ............................................ -0.5V to VCC CML Output Voltage (VOUT) ............... VCC-1.0V to VCC+0.5V Current (VT) Source or sink current on VT pin ....................... ±100mA Input Current Source or sink current on IN, /IN ........................ ±50mA Current (VREF) Source or sink current on VREF-AC(6), .................. ±1.5mA Lead Temperature Soldering, (20 sec.) ..................... 260°C Storage Temperature Range (TS) .............. -65°C to +150°C Supply Voltage (VCC) .............................. +2.375V to +3.60V Ambient Temperature (TA) .......................... –40°C to +85°C Junction Thermal Resistance QFN (θJA) Still-Air ....................................................... 60°C/W 500lfpm ...................................................... 54°C/W QFN (ΨJB) (Junction-to-Board Resistance)(5) .............. 33°C/W DC Electrical Characteristics(7) TA = -40°C to +85°C. Symbol Parameter VCC Power Supply Voltage Condition Min. VCC = 2.5V VCC = 3.3V Typ. Max. Units 2.375 2.500 2.625 V 3.000 3.300 3.600 V 150 180 mA VCC-1.600 VCC V 0 VIH-0.100 V ICC Power Supply Current No Load, VCC = max. (include internal 50Ω pull-up) VIH Input HIGH Voltage Note 8 VIL Input LOW Voltage VIN Input Voltage Swing See Figure 1. 0.100 1.700 V VDIFF_IN Differential Input Voltage Swing See Figure 2. 0.200 3.400 V RIN IN-to-VT Resistance Ω VREF-AC Output Reference Voltage VT IN IN-to-VT Voltage 40 50 60 VCC-1.300 VCC-1.200 VCC-1.100 V 1.280 V CML DC Electrical Characteristics(7) VCC = 3.3V ±10% or 2.5V ±5%; RL = 100Ω across each output pair or equivalent; TA = -40°C to +85°C, unless otherwise stated. Symbol Parameter VOH Output HIGH Voltage VOUT Output Voltage Swing VDIFF_OUT Differential Output Voltage Swing ROUT Output Source Impedance Condition Min. Typ. Max. Units VCC-0.020 VCC-0.010 VCC V See Figure 1. 325 400 500 mV See Figure 2. 650 800 1000 mV 40 50 60 Ω Notes: 3. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratings conditions for extended periods may affect device reliability. 4. The data sheet limits are not guaranteed if the device is operated beyond the operating ratings. 5. Thermal performance assumes exposed pad is soldered (or equivalent) to the device’s most negative potential on the PCB. 6. Due to the limited drive capability, use for input of the same package only. 7. The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. 8. VIH (min) not lower than 1.2V. October 27, 2014 3 Revision 5.0 tcghelp@micrel.com or (408) 955-1690 Micrel, Inc. SY58020U AC Electrical Characteristics VCC = 2.5V ±5% or 3.3V ±10%; TA = -40°C to +85°C; RL = 100Ω across each output pair or equivalent, unless otherwise stated. Symbol Parameter fMAX Maximum Operating Frequency tpd Propagation Delay tSKEW tr , tf tJITTER Condition VOUT ≥ 200mV Clock Part-to-Part Skew Note 10 Ouptut Rise/Fall Time 20% to 80% At full swing Max. 20 Units GHz 10 110 Note 9 Typ. 6 NRZ Data Output-to-Output Skew Additive Phase Jitter Min. Gbps 180 260 ps 4 15 ps 50 ps 60 ps 40 Carrier = 622MHz Integration Range: 12kHz – 20MHz 27 Carrier = 156.25MHz Integration Range: 12kHz – 20MHz 128 fsRMS Notes: 9. Skew is measured between outputs under identical transitions. 10. Skew is defined for two parts with identical power supply voltages at the same temperature and with no skew of the edges at the respective inputs. Timing Diagram Single-Ended and Differential Swings Figure 1. Single-Ended Voltage Swing October 27, 2014 Figure 2. Differential Voltage Swing 4 Revision 5.0 tcghelp@micrel.com or (408) 955-1690 Micrel, Inc. SY58020U Typical Operating Characteristics VCC = 2.5V, GND = 0, VIN = 100mV, TA = 25°C, unless otherwise stated. October 27, 2014 5 Revision 5.0 tcghelp@micrel.com or (408) 955-1690 Micrel, Inc. SY58020U Functional Characteristics VCC = 2.5V, GND = 0, VIN = 100mV, TA = 25°C, unless otherwise stated. October 27, 2014 6 Revision 5.0 tcghelp@micrel.com or (408) 955-1690 Micrel, Inc. SY58020U Additive Phase Noise Plots VCC = 3.3V, GND = 0, TA = 25°C. October 27, 2014 7 Revision 5.0 tcghelp@micrel.com or (408) 955-1690 Micrel, Inc. SY58020U Input Stage Figure 3. Simplified Differential Input Buffer Input Interface Applications Figure 4. DC-Coupled CML Input Interface Figure 5. AC-Coupled CML Input Interface Figure 6. LVDS Input Interface Figure 7. AC-Coupled LVDS Input Interface. Note: Be certain that the LVDS driver can be AC-coupled. October 27, 2014 Figure 8. LVPECL Input Interface 8 Figure 9. AC-Coupled LVPECL Input Interface Revision 5.0 tcghelp@micrel.com or (408) 955-1690 Micrel, Inc. SY58020U CML Output Termination Figures 10 and 11 illustrate a CML output using both the AC-coupled and DC-coupled configuration. All outputs of the SY58020U are 50Ω with a 16mA current source. Figure 11. CML AC-Coupled Termination Figure 10. CML DC-Coupled October 27, 2014 9 Revision 5.0 tcghelp@micrel.com or (408) 955-1690 Micrel, Inc. SY58020U Package Information(16) October 27, 2014 10 Revision 5.0 tcghelp@micrel.com or (408) 955-1690 Micrel, Inc. October 27, 2014 SY58020U 11 Revision 5.0 tcghelp@micrel.com or (408) 955-1690 Micrel, Inc. SY58020U 16-Pin Package Type (QFN-16) Note: 11. Package information is correct as of the publication date. For updates and most current information, go to www.micrel.com. MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com Micrel, Inc. is a leading global manufacturer of IC solutions for the worldwide high performance linear and power, LAN, and timing & communications markets. The Company’s products include advanced mixed-signal, analog & power semiconductors; high-performance communication, clock management, MEMs-based clock oscillators & crystal-less clock generators, Ethernet switches, and physical layer transceiver ICs. Company customers include leading manufacturers of enterprise, consumer, industrial, mobile, telecommunications, automotive, and computer products. Corporation headquarters and state-of-the-art wafer fabrication facilities are located in San Jose, CA, with regional sales and support offices and advanced technology design centers situated throughout the Americas, Europe, and Asia. Additionally, the Company maintains an extensive network of distributors and reps worldwide. Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this datasheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel’s terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the2014 body or (b) support or sustain life, and whose failure to perform to the user. A 5.0 October 27, 12 can be reasonably expected to result in a significant injuryRevision Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully tcghelp@micrel.com or (408) 955-1690 indemnify Micrel for any damages resulting from such use or sale. © 2005 Micrel, Incorporated. Micrel, Inc. SY58020U Revision History Date Change Description/Edits by: 8/4/10 Added new paragraph to disclaimer in boiler plate. Per Colin Sturt. M.Galvan 14 1/16/13 Complete rework 15 5/8/14 Updated Contact Email 16 October 27, 2014 Rev. 13 Revision 5.0 tcghelp@micrel.com or (408) 955-1690