TC32MCDB

TC32M ECONOMONITOR™ – 3-Pin System Supervisor with Power Supply Monitor and Watchdog Features: General Description: • Incorporates the Functionality of the Industry Standard TC1232 (Processor Monitor, Watchdog and Manual Override Reset Controller) into a Small, Lower Cost Package • Guards Against Unstable Processor Operation Resulting from Power “Brown-Out” • Automatically Halts and Restarts an Out-ofControl Microprocessor • Output can be Wire-ORed, or Hooked to Manual Reset Push-button Switch • Space-Saving 3-Pin TO-92 or SOT-223 Package The TC32M is a fully-integrated processor supervisor in a 3-pin package. It provides three important functions to safeguard processor sanity: precision power on/off Reset control, Watchdog Timer and external Reset override. Applications: • • • • • • All Microprocessor-Based Systems Battery Powered Computers and Controllers Automotive Systems Intelligent Instruments Critical Processor Monitoring Embedded Controllers The output of the TC32M can be wire-ORed with a push-button switch (or electronic signal) to override the TC32M and unconditionally reset the processor. When connected to a push-button switch, the TC32M provides contact debounce. Device Selection Table Part Number TC32MCDB On power-up, the TC32M holds the processor in the Reset state for a minimum of 500 msec after VDD is within tolerance to ensure a stable system start-up. Microprocessor sanity is monitored by the on-board Watchdog circuit. The microprocessor must provide a high-to-low level shift (through an external resistor divider) on the RS pin of the TC32M. Should the processor fail to supply this signal within the specified time-out period (typically 700 msec), an out-of-control processor is indicated and the TC32M issues a processor Reset as a result. Package Temp. Range SOT-223 0°C to +70°C TC32MCZB TO-92 0°C to +70°C TC32MEDB SOT-223 -40°C to +85°C TC32MEZB TO-92 -40°C to +85°C The TC32M is packaged in a space-saving TO-92 or SOT-223 package. It provides all of the functionality of the industry standard TC1232 in a smaller, lower cost configuration. Package Type 1 2 3 VDD 4 TC32MCDB TC32MEDB 1 2 3 GND VDD RS RS VDD GND TC32MCZB TC32MEZB  2001-2012 Microchip Technology Inc. DS21402D-page 1 TC32M Functional Block Diagram Typical Operating Circuit VDD 5V TC32M VREF1 R1, 10 kΩ Watchdog Timer DV Detector Microcontroller R2, 10 kΩ PO.1 RS Reset RS TC32M VREF2 Reset Delay Timer GND DS21402D-page 2  2001-2012 Microchip Technology Inc. TC32M 1.0 ELECTRICAL CHARACTERISTICS *Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of the specifications is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Absolute Maximum Ratings* Supply Voltage (VDD to GND) .............................+6.0V Input Voltage Any Pin..... (GND – 0.3V) to (VDD +0.3V) Operating Temperature Range TC32MC Package........................... 0°C to +70°C TC32ME Package ........................ -40°C to +85°C Storage Temperature Range ............. -65°C to +150°C TC32M ELECTRICAL SPECIFICATIONS Recommended DC Operating Conditions: TA = -40°C to +85°C unless otherwise noted. Symbol Parameter Min Typ Max Units VDD Supply Voltage 4.5 — 5.5 V VIH RS Input HIGH Level for PB 2.0 — — V VIL RS Input LOW Level for PB — — 0.3 V Test Conditions DC Electrical Characteristics: VDD = 4.5V to 5.5V, TA = -40°C to +85°C unless otherwise noted. Symbol Parameter Min Typ Max Units Test Conditions IIL RS Input Leakage -1 — +1 mA IOL RS Output Current 2.0 10 — mA VOL = 0.4V ICC Operating Current — 50 200 A Note 1 VSTH RS Strobe HIGH Level (VDD – 0.5V) — — V Figure 3-1 VSTL RS Strobe LOW Level 2.00 — (VDD – 1.5V) V Figure 3-1 VRST Reset Threshold 4.25 — 4.50 V VDD Falling (Note 2, Figure 3-3) Test Conditions Capacitance Electrical Characteristics: TA = 25°C unless otherwise noted. Symbol Parameter Min Typ Max Units CIN Input Capacitance — — 5 pF COUT Output Capacitance — — 7 pF AC Electrical Characteristics: TA = -40°C to +85°C, VDD = 5V ±10%, unless otherwise noted. Symbol Parameter Min Typ Max Units msec Figure Test Conditions tRST Reset Active Time 500 700 900 tST RS Strobe Pulse Width 500 — — nsec Figure 3-1 500 700 900 msec Figure 3-1 — — tTD Watchdog Time-out Period tRPD VDD Detect to RS LOW Note 1: 2: No output load. All voltages referenced to ground.  2001-2012 Microchip Technology Inc. nsec Figure 3-1 DS21402D-page 3 TC32M 2.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 2-1. TABLE 2-1: PIN FUNCTION TABLE Pin No. (SOT-223, TO-92) Symbol 1 GND Ground. 2 VDD The +5V power supply input. 3 RS Reset/Strobe (Bidirectional). The open drain goes active if: VDD falls below 4.5V nominal. If pulled low by an external electronic signal or switch closure. If the Watchdog is not strobed within the minimum Watchdog Time-out period. During power-up and power-down. In the Input mode, RS connects to a voltage level shift network (typically a resistor divider to VDD.) The Watchdog Timer is reset when processor causes a voltage level  VSTL to be applied to RS. 4 VDD The +5V power supply input (SOT-223 only). DS21402D-page 4 Description  2001-2012 Microchip Technology Inc. TC32M 3.0 DETAILED DESCRIPTION The TC32M provides three important functions to safeguard stable processor operation: precision processor monitor, Watchdog sanity timer and external override Reset control. 3.1 Processor Monitor The RS pin is immediately driven low any time VDD is below the nominal threshold voltage. As a result, this pin is LOW when power is initially applied, holding the processor in its Reset state. RS remains low for a minimum of 500 msec after VDD is within tolerance to allow the power supply and processor to stabilize. 3.2 Watchdog Timer The processor drives the RS pin with an input/output (I/O) line in series with an resistor voltage divider to VDD. Pulling the bottom resistor of this divider low results in an internal voltage change (strobe) sufficient to reset the Watchdog Timer, but above the VIL input threshold of the processor Reset pin. The processor must continuously apply strobes in this manner within a set period to verify proper software execution. A momentary Reset (500 msec minimum) is generated by the TC32M if a hardware or software failure keeps RS from being strobed within the Watchdog Time-out period. This action typically initiates the processor’s power-up routine. If the interruption persists, new Reset pulses are generated each time-out period until RS is strobed. This time-out period is typically 700 msec.  2001-2012 Microchip Technology Inc. tST RS VSTH (Min) VSTL (Max) VSTL (Min) tTD Note: tTD is the maximum elapsed time between strobes which will keep the watchdog timer from forcing RS LOW. (A Strobe is defined as a high-to-low transition from VSTH to VSTL). FIGURE 3-1: Watchdog Strobe The software routine that drives the RS strobe must be in a section of the program that executes frequently enough so the time between toggles is less than one Watchdog Time-out period. The strobe signal can be derived from microprocessor address, data and/or control signals. Typical circuit examples are shown in Figure . 3.3 Resistor Value Selection The values of R1 and R2 must be chosen to ensure a valid low strobe level (VSTL) on RS when the processor I/O line is low. The use of 10 k, ±5% tolerance resistors are recommended. These values result in a nominal strobe level of 2.5 on RS (min/max of 2.13V/ 3.08V, assuming VDD = 5.0V ±10%). Other resistor values can be used, so long as the additive tolerances of the power supply and resistor values result in a strobe that falls within VSTH and VSTL under all additive tolerance conditions. DS21402D-page 5 TC32M 3.4 External Override Reset Control VDD A built-in debounce circuit allows a push-button switch (PB) or other electronic signal to be wire-ORed to this pin as an external Reset override control. The external Reset is required to be an active low signal. Internally, this input is timed to provide a minimum Reset pulse width of 500 msec. Reference Figure . VRST tRPD t PB Closed RS PB Open VIH VIL FIGURE 3-3: RS VIH 3.5 VIL RS Pulled Low By PushButton Reset Microcontroller Supply Monitor Noise Sensitivity 5V 5V R1, 10 kΩ Microprocessor R1, 10 kΩ R2, 10 kΩ R2,10 kΩ PO.1 Power-Up/Down Reset Timing The TC32M is optimized for fast response to negativegoing changes in VDD. Systems with an inordinate amount of electrical noise on VDD (such as systems using relays), may require a 0.01 F bypass capacitor to reduce detection sensitivity. This capacitor should be installed as close to the TC32M as possible to keep the capacitor lead length short. tRST FIGURE 3-2: tRST Decoder RS Address TC32M RS Reset Reset TC32M Reset Microcontroller Example FIGURE 3-4: DS21402D-page 6 Reset Microprocessor Example TC32M Hardware Connections (R1, R2 Chosen To Meet VSTH, VSTL)  2001-2012 Microchip Technology Inc. TC32M 4.0 PACKAGING INFORMATION 4.1 Package Marking Information Package marking data not available at this time. 4.2 Taping Form Component Taping Orientation for 3-Pin SOT-223 Devices User Direction of Feed Device Marking W Pin 1 P Standard Reel Component Orientation for 713 Suffix Device (Mark Right Side Up) Carrier Tape, Number of Components Per Reel and Reel Size Package 3-Pin SOT-223 Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size 12 mm 8 mm 4000 13 in Component Taping Orientation for 3-Pin TO-92 User Direction of Feed P Mark Face MARK FACE MARK FACE MARK FACE Back Tape  2001-2012 Microchip Technology Inc. W Seal Tape DS21402D-page 7 TC32M 4.3 Package Dimensions Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 3-Pin SOT-223 .264 (6.70) .248 (6.30) .122 (3.10) .114 (2.90) .287 (7.30) .146 (3.70) .264 (6.70) .130 (3.30) .041 (1.04) .033 (0.84) Pin 1 .091 (2.30) Typ. .031 (0.80) .024 (0.60) .071 (1.80) Max. .013 (0.33) .009 (0.24) 10° Max. .004 (0.10) .001 (0.02) .181 (4.60) Typ. .036 (0.91) Min. Dimensions: inches (mm) Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging TO-92-3 .165 (4.19) .125 (3.18) .210 (5.33) .170 (4.32) .500 (12.70) Min. .205 (5.21) .175 (4.45) .105 (2.67) .080 (2.03) .105 (2.67) .095 (2.41) .018 (0.46) .015 (0.38) .135 (3.43) Min. .055 (1.40) .045 (1.14) .018 (0.46) .015 (0.38) Dimensions: inches (mm) DS21402D-page 8  2001-2012 Microchip Technology Inc. TC32M 5.0 REVISION HISTORY Revision D (December 2012) Added a note to each package outline drawing.  2001-2012 Microchip Technology Inc. DS21402D-page 9 TC32M NOTES: DS21402D-page 10  2001-2012 Microchip Technology Inc. TC32M PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART CODE TC32M X XX Temperature: C: Commercial (0°C to +70°C) E: Extended (-40°C to +85°C) Package Type: ZB: 3-Pin TO-92 DB: 3-Pin SOT223 DB713: 3-Pin Tape & Reel SOT223 Sales and Support Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. Your local Microchip sales office The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products.  2001-2012 Microchip Technology Inc. DS21402D-page11 TC32M NOTES: DS21402D-page12  2001-2012 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MTP, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. Analog-for-the-Digital Age, Application Maestro, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O, Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA and Z-Scale are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. GestIC and ULPP are registered trademarks of Microchip Technology Germany II GmbH & Co. & KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. © 2001-2012, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 9781620767894 QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV == ISO/TS 16949 ==  2001-2012 Microchip Technology Inc. Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. DS21402D-page 13 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Osaka Tel: 81-66-152-7160 Fax: 81-66-152-9310 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 China - Hangzhou Tel: 86-571-2819-3187 Fax: 86-571-2819-3189 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Hong Kong SAR Tel: 852-2943-5100 Fax: 852-2401-3431 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 China - Shenzhen Tel: 86-755-8864-2200 Fax: 86-755-8203-1760 Taiwan - Kaohsiung Tel: 886-7-213-7828 Fax: 886-7-330-9305 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Taipei Tel: 886-2-2508-8600 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 DS21402D-page 14 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 11/27/12  2001-2012 Microchip Technology Inc.