ACT6906UCADJ-T

Data Sheet Rev 0, 5/2006 ACT6906 1.6MHz, 600mA Synchronous Step Down Converter in SOT23-5 FEATURES           GENERAL DESCRIPTION The ACT6906 is a fixed-frequency currentmode synchronous PWM step down converter that is capable of delivering 600mA of output current while achieving peak efficiency of 95%. Under light load conditions, the ACT6906 operates in a proprietary pulse skipping mode that consumes just 24µA of supply current, maximizing battery life in portable applications. The ACT6906 operates with a fixed frequency of 1.6MHz, minimizing noise in noise-sensitive applications and allowing the use of small external components. The ACT6906 is an ideal solution for applications powered by Li-Ion batteries or other portable applications that require small board space. High Efficiency - Up to 95% Very Low 24µA Quiescent Current Guaranteed 600mA Output Current 1.6MHz Constant Frequency Operation Internal Synchronous Rectifier Eliminates Schottky Diode Adjustable Output Voltages From 0.6V to VIN Fixed Output Voltage Options Available 100% Duty Cycle Low-Dropout Operation 0.1µA Shutdown Current Tiny SOT23-5 Package APPLICATIONS       The ACT6906 is available in a variety of fixed output voltage options, 1.5V, 1.8V, and 2.5V, and is also available in an adjustable output voltage version capable of generating output voltages from 0.6V to VIN .The ACT6906 is available in a tiny 5-pin SOT23-5 package. Blue Tooth Headsets Portable Audio Players Mobile Phones Wireless and DSL Modems Digital Still Cameras Portable Instruments Figure 1. Typical Application Circuit and Efficiency Active-Semi, Inc. -1- www.active-semi.com ACT6906 ORDERING INFORMATION (1) (2) PART NUMBER (1)(2) TEMPERATURE RANGE OUTPUT VOLTAGE (V) PACKAGE TOP MARK ACT6906UC150-T -40° C to 85°C 1.5 SOT23-5 IAFX ACT6906UC180-T -40° C to 85°C 1.8 SOT23-5 IAFA ACT6906UC250-T -40° C to 85°C 2.5 SOT23-5 IAFB ACT6906UCADJ-T -40° C to 85°C Adjustable SOT23-5 IAFM Contact factory for other output voltage options -T denotes Tape & Reel packing PIN CONFIGURATION EN 1 G 2 SW 3 5 FB 4 IN ACT6906 UC SOT23-5 PIN DESCRIPTION PIN NUMBER PIN NAME 1 EN 2 3 G SW 4 IN 5 FB Active-Semi, Inc. PIN DESCRIPTION Enable Control Input. Drive EN to IN or to a logic high for normal operation, drive to G or a logic low to disable the regulator. Ground. Switching Node Output. Connect this pin to the switching end of the inductor. Power Input. Bypass to G as close as possible to the IC with a high quality ceramic capacitor. Feedback Node. For fixed output voltage options, connect this pin directly to the output. For the adjustable output version the voltage at this pin is regulated to 0.6V; connect to this pin to the center of the output voltage feedback network. -2- www.active-semi.com ACT6906 ABSOLUTE MAXIMUM RATINGS (Note: Exceeding these limits may damage the device. Exposure to absolute maximum rating conditions for long periods may affect device reliability.) PARAMETER IN, FB, EN to G SW to G Continuous SW Current Junction to Ambient Thermal Resistance (θ JA) Maximum Power Dissipation (derate 5.3mW/°C above TA = 50°C) Operating Junction Temperature Storage Temperature Lead Temperature (Soldering, 10 sec) VALUE UNIT -0.3 to 6 -0.3 to VIN + 0.3 Internally limited 190 0.53 -40 to 150 -55 to 150 300 V V A °C/W W °C °C °C ELECTRICAL CHARACTERISTICS (VIN = VEN = 3.6V, TA = 25˚C unless otherwise specified.) PARAMETER Input Voltage Range Under Voltage Lockout Threshold Operating Supply Current Standby Supply Current Shutdown Supply Current SYMBOL VIN VUVLO Adjustable Version Regulation Voltage (ACT6906UCADJ) VFB Fixed Output Regulation Voltage VOUT Output Voltage Line Regulation Output Voltage Load Regulation Inductor Current Limit ILIM Oscillator Frequency fSW PMOS On Resistance NMOS On Resistance SW Leakage Current EN Logic High Threshold EN Logic Low Threshold EN Input Bias Current Active-Semi, Inc. RONP RONN VIH VIL IEN TEST CONDITIONS VIN rising, hysteresis = 0.1V VFB = 60%, IOUT = 0 VFB = 105%, IOUT = 0 VEN = 0V, VIN = 4.2V TA = 25°C 0 < TA < 85°C -40°C < TA < 85°C ACT6906UC150 ACT6906UC180 ACT6906UC250 VIN = 3V to 5V IOUT = 10mA to 500mA VIN = 3.6V, VFB = 90% of VOUT(NOM) VFB or VOUT in regulation VFB or VOUT = 80% of VOUT(NOM) ISW = -100mA ISW = 100mA EN = G, VIN = 5.5V, VSW = 5.5V or 0V VIN = 2.7V to 5.5V VIN = 2.7V to 5.5V VIN = 5.5V, EN = G or IN -3- MIN 2.7 2.25 0.591 0.588 0.582 1.473 1.768 2.455 1.3 TYP 2.4 586 22 0.1 0.6 0.6 0.6 1.5 1.8 2.5 0.016 0.5 0.9 1.6 360 0.37 0.36 MAX UNIT 5.5 2.5 V V µA µA µA 33 5 0.609 0.612 0.618 1.527 1.832 2.545 0.4 1.9 0.6 0.6 1 1.4 0.01 0.4 0.1 V V %/V % A MHz kHz Ω Ω µA V V µA www.active-semi.com ACT6906 IN CURRENT SENSE OSC & RAMP GENERATOR LOGIC AND CONTROL CIRCUITRY EN SW ZERO CROSS DETECT VREF INTERNAL COMPENSATION gm FB G Figure 2. Functional Block Diagram switching frequency in order to achieve high efficiency. Whenever the feedback voltage falls below the regulation voltage the high-side MOSFET turns on and remains on for a period of time that is controlled by the ACT6906 control circuitry. The duration of the on cycle is dynamically adjusted to maximize efficiency under all load current conditions. FUNCTIONAL DESCRIPTION CONTROL SCHEME The ACT6906 utilizes a fixed-frequency, current-mode PWM control scheme combined with fully-integrated power MOSFETs to produce a compact and efficient step-down DC-DC solution. During normal operation the high-side MOSFET turns on each cycle and remains on until the current comparator turns it off. At this point the low-side MOSFET turns on and remains on until either the end of the switching cycle or until the inductor current approaches zero. The error amplifier adjusts the current comparator's threshold as necessary in order to ensure that the output voltage remains in regulation. SOFT START The ACT6906 integrates a 50µs soft start function that prevents input inrush current and output overshoot during start up. OVER-CURRENT PROTECTION The ACT6906 has an internal current limit of 900mA, which is detected on a cycle by cycle basis. When this maximum inductor current limit is reached the charging cycle is terminated, and the low-side MOSFET is turned on to allow the inductor current to decrease. Under extreme overloads, such as short-circuit conditions, the ACT6906 reduces it's oscillator frequency to 360kHz to allow further inductor current reduction and to minimize power dissipation. LIGHT LOAD POWER SAVING OPERATION When operating under light-load conditions, the ACT6906 uses a proprietary and patentpending control scheme that reduces quiescent supply current to maximize efficiency while maintaining output voltage regulation. Under light load conditions the ACT6906 reduces it's Active-Semi, Inc. -4- www.active-semi.com ACT6906 APPLICATION INFORMATION OUTPUT CAPACITOR SELECTION INDUCTOR SELECTION A low ESR output capacitor is required in order to maintain low output voltage ripple. Output ripple voltage is given by: Under normal operation, the inductor maintains continuous current to the output. This inductor current has a ripple that is dependent on the inductance value: higher inductance reduces the peak-to-peak ripple current. In general, select an inductance value L based on ripple current requirement: V • (VIN − VOUT ) L = OUT VIN fSW IOUTMAX K RIPPLE VRIPPLE = I OUTMAX K RIPPLE R ESR + VIN (2) 28 • f SW 2 LCOUT where IOUTMAX is the maximum output current, KRIPPLE is the ripple factor, RESR is the ESR of the output capacitor, fSW is the switching frequency, L is the inductor value, and COUT is the output capacitance. In the case of ceramic output capacitors, RESR is very small and does not contribute to the ripple. Therefore, a lower capacitance value is acceptable when ceramic capacitors are used. A 10µF ceramic output capacitor is suitable for most applications. (1) where VIN is the input voltage, VOUT is the output voltage, fSW is the switching frequency, IOUTMAX is the maximum output current, and KRIPPLE is the ripple factor. Typically, choose KRIPPLE = 30% to correspond to the peak-to-peak ripple current being 30% of the maximum output current. With this inductor value (Table 1), the peak inductor current is IOUT • (1 + KRIPPLE / 2). Make sure that this peak inductor current is less than the 0.9A current limit. Finally, select the inductor core size so that it does not saturate at the current limit value. OUTPUT VOLTAGE PROGRAMMING VOUT RFB1 ACT6906 FB Table 1. Typical Inductor Values VOUT L 0.6V to 0.9V 1.5μH 0.9V to 1.8V 2.2μH RFB2 >1.8V 2.7μH Figure 3. Output Voltage Programming Figure 3 shows the feedback network necessary to set the output voltage when the adjustable version is used. Select the proper ratio of the two feedback resistors RFB1 and RFB2 based on the desired output voltage. Typically choose RFB2 ≈ 100kΩ and determine RFB1 from the output voltage: INPUT CAPACITOR SELECTION The input capacitor reduces input voltage ripple to the converter; a 4.7μF ceramic capacitor is recommended for most applications. The input capacitor should be placed as close as possible to IN and G, with short, wide traces. V  RFB1 = RFB2  OUT − 1  0.6V   (3) Connect a small capacitor across RFB1 for Feed forward capacitance at the FB pin: Cff = 2E − 5/RFB1 (4) where RFB1 = 900KΩ, use 22pF. When using very low ESR output capacitors, such as ceramic, check for stability while examining load-transient response, and increase the compensation capacitor C1 if needed. Active-Semi, Inc. -5- www.active-semi.com ACT6906 TYPICAL PERFORMANCE CHARACTERISTICS (VIN = VEN = 3.6V, L = 2.2µH, CIN = 4.7μF, COUT = 10μF, unless otherwise specified.) Active-Semi, Inc. -6- www.active-semi.com ACT6906 TYPICAL PERFORMANCE CHARACTERISTICS CONT'D (VIN = VEN = 3.6V, L = 2.2µH, CIN = 4.7μF, COUT = 10μF, unless otherwise specified.) Active-Semi, Inc. -7- www.active-semi.com ACT6906 PACKAGE OUTLINE SOT23-5 PACKAGE OUTLINE AND DIMENSIONS SYMBOL A A1 A2 b c D E E1 e e1 L L1 θ DIMENSION IN MILLIMETERS MIN MAX 1.050 1.250 0.000 0.100 1.050 1.150 0.300 0.400 0.100 0.200 2.820 3.020 1.500 1.700 2.650 2.950 0.950 TYP 1.800 2.000 0.700 REF 0.300 0.600 0° 8° DIMENSION IN INCHES MIN MAX 0.041 0.049 0.000 0.004 0.041 0.045 0.012 0.016 0.004 0.008 0.111 0.119 0.059 0.067 0.104 0.116 0.037 TYP 0.071 0.079 0.028 REF 0.012 0.024 0° 8° Active-Semi, Inc. reserves the right to modify the circuitry or specifications without notice. Users should evaluate each product to make sure that it is suitable for their applications. Active-Semi products are not intended or authorized for use as critical components in life-support devices or systems. Active-Semi, Inc. does not assume any liability arising out of the use of any product or circuit described in this data sheet, nor does it convey any patent license. Active-Semi and its logo are trademarks of Active-Semi, Inc. For more information on this and other products, contact sales@active-semi.com or visit www.active-semi.com. For other inquiries, please send to: 1270 Oakmead Parkway, Suite 310, Sunnyvale, California 94085-4044, USA Active-Semi, Inc. -8- www.active-semi.com