AD22103KR-REEL

AD22103–SPECIFICATIONS (T = +25°C and V = +2.7 V to +3.6 V unless otherwise noted) A Parameter S AD22103K Typ Min Max VOUT = (VS/3.3 V) × [0.25 V + (28 mV/°C) × TA] TRANSFER FUNCTION V (VS/3.3 V) × 28 TEMPERATURE COEFFICIENT TOTAL ERROR Initial Error TA = +25°C Error over Temperature TA = TMIN to TMAX Nonlinearity TA = TMIN to TMAX OUTPUT CHARACTERISTICS Nominal Output Voltage VS = 3.3 V, TA = 0°C VS = 3.3 V, TA = +25°C VS = 3.3 V, TA = +100°C mV/°C ± 0.5 ± 2.0 °C ± 0.75 ± 2.5 °C 0.1 0.5 % FS1 0.25 0.95 3.05 POWER SUPPLY Operating Voltage Quiescent Current +2.7 350 TEMPERATURE RANGE Guaranteed Temperature Range Operating Temperature Range 0 0 +3.3 500 PACKAGE Units V V V +3.6 600 V µA +100 +100 °C °C TO-92 SOIC NOTES 1 FS (Full Scale) is defined as that of the operating temperature range, 0 °C to +100°C. The listed max specification limit applies to the guaranteed temperature range. For example, the AD22103K has a nonlinearity of (0.5%) × (100°C) = 0.5°C over the guaranteed temperature range of 0°C to +100°C. Specifications subject to change without notice. CHIP SPECIFICATIONS (T = +25°C and V = +3.3 V unless otherwise noted) A S Parameter Min Typ TRANSFER FUNCTION VOUT = (VS/3.3 V) × [0.25 V + (28 mV/°C) × TA] Max V (VS/3.3 V) × 28 TEMPERATURE COEFFICIENT OUTPUT CHARACTERISTICS Error TA = +25°C Nominal Output Voltage TA = +25°C ± 0.5 mV/°C Note 1 0.95 POWER SUPPLY Operating Voltage Quiescent Current +2.7 350 TEMPERATURE RANGE Guaranteed Temperature Range Operating Temperature Range 0 +3.3 500 Units °C V +3.6 600 V µA +100 °C °C 25 NOTES 1 Max specs cannot be guaranteed on chips, however, performance once assembled should be commensurate with the specifications listed in the top table. Specifications subject to change without notice. –2– REV. 0 AD22103 PIN DESCRIPTION ABSOLUTE MAXIMUM RATINGS* Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +10 V Reversed Continuous Supply Voltage . . . . . . . . . . . . . . . –10 V Operating Temperature . . . . . . . . . . . . . . . . . . 0°C to +100°C Storage Temperature . . . . . . . . . . . . . . . . . . . –65°C to +160°C Output Short Circuit to VS or Ground . . . . . . . . . . . . Indefinite Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . . +300°C Mnemonic Function VS VO GND NC Power Supply Input Device Output Ground Pin Must Be Connected to 0 V No Connect *Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; the functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. PIN CONFIGURATIONS TO-92 AD22103 ORDERING GUIDE BOTTOM VIEW (Not to Scale) Model/Grade Guaranteed Temperature Range Package Description Package Option AD22103KT AD22103KR 0°C to +100°C 0°C to +100°C TO-92 SOIC TO-92 SO-8 N/A N/A AD22103KChips* +25°C PIN 3 PIN 2 PIN 1 GND VO VS SOIC *Minimum purchase quantities of 100 pieces for all chip orders. 8 NC VS 1 VO 2 AD22103 7 NC TOP VIEW NC 3 (Not to Scale) 6 NC GND 4 5 NC NC = NO CONNECT CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD22103 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. WARNING! ESD SENSITIVE DEVICE Typical Performance Curves 250 18 14 200 8 (SOIC) T (TO-92) θJA – °C/W – Sec 10 τ 12 6 100 T (SOIC) 4 2 (TO-92) 50 0 400 800 FLOW RATE – CFM 1200 Figure 2. Thermal Response vs. Air Flow Rate REV. 0 150 0 400 800 FLOW RATE – CFM 1200 Figure 3. Thermal Resistance vs. Air Flow Rate –3– AD22103 THEORY OF OPERATION OUTPUT STAGE CONSIDERATIONS The AD22103 is a ratiometric temperature sensor IC whose output voltage is proportional to power supply voltage. The heart of the sensor is a proprietary temperature-dependent resistor, similar to an RTD, which is built into the IC. Figure 4 shows a simplified block diagram of the AD22103. As previously stated, the AD22103 is a voltage output device. A basic understanding of the nature of its output stage is useful for proper application. Note that at the nominal supply voltage of 3.3 V, the output voltage extends from 0.25 V at 0°C to +3.05 V at +100°C. Furthermore, the AD22103 output pin is capable of withstanding an indefinite short circuit to either ground or the power supply. These characteristics are provided by the output stage structure shown in Figure 6. +VS VS Ι VOUT VOUT RT Ι Figure 4. Simplified Block Diagram Figure 6. Output Stage Structure The temperature-dependent resistor, labeled R T, exhibits a change in resistance that is nearly linearly proportional to temperature. This resistor is excited with a current source that is proportional to power supply voltage. The resulting voltage across R T is therefore both supply voltage proportional and linearly varying with temperature. The remainder of the AD22103 consists of an op amp signal conditioning block that takes the voltage across R T and applies the proper gain and offset to achieve the following output voltage function: The active portion of the output stage is a PNP transistor with its emitter connected to the VS supply and collector connected to the output node. This PNP transistor sources the required amount of output current. A limited pull-down capability is provided by a fixed current sink of about –100 µA. (Here, “fixed” means the current sink is fairly insensitive to either supply voltage or output loading conditions. The current sink capability is a function of temperature, increasing its pull-down capability at lower temperatures.) VOUT = (VS/3.3 V) × [0.25 V + (28.0 mV/°C) × TA] Due to its limited current sinking ability, the AD22103 is incapable of driving loads to the VS power supply and is instead intended to drive grounded loads. A typical value for short circuit current limit is 7 mA, so devices can reliably source 1 mA or 2 mA. However, for best output voltage accuracy and minimal internal self-heating, output current should be kept below 1 mA. Loads connected to the VS power supply should be avoided as the current sinking capability of the AD22103 is very limited. These considerations are typically not a problem when driving a microcontroller analog to digital converter input pin (see MICROPROCESSOR A/D INTERFACE ISSUES). ABSOLUTE ACCURACY AND NONLINEARITY SPECIFICATIONS Figure 5 graphically depicts the guaranteed limits of accuracy for the AD22103 and shows the performance of a typical part. As the output is very linear, the major sources of error are offset, i.e., error at room temperature, and span error, i.e., deviation from the theoretical 28.0 mV/°C. Demanding applications can achieve improved performance by calibrating these offset and gain errors so that only the residual nonlinearity remains as a source of error. MOUNTING CONSIDERATIONS If the AD22103 is thermally attached and properly protected, it can be used in any measuring situation where the maximum range of temperatures encountered is between 0°C and +100°C. Because plastic IC packaging technology is employed, excessive mechanical stress must be avoided when fastening the device with a clamp or screw-on heat tab. Thermally conductive epoxy or glue is recommended for typical mounting conditions. In wet or corrosive environments, an electrically isolated metal or ceramic well should be used to shield the AD22103. Because the part has a voltage output (as opposed to current), it offers modest immunity to leakage errors, such as those caused by condensation at low temperatures. 2.5 2.0 1.5 ERROR – °C 1.0 VS = 3.6V 0.5 VS = 3.3V 0 VS = 2.7V –0.5 –1.0 –1.5 –2.0 –2.5 0 50 TEMPERATURE – °C 100 Figure 5. Typical AD22103 Performance –4– REV. 0 AD22103 neglected in the analysis; however, they will sink or conduct heat directly through the AD22103’s solder plated copper leads. When faster response is required, a thermally conductive grease or glue between the AD22103 and the surface temperature being measured should be used. THERMAL ENVIRONMENT EFFECTS The thermal environment in which the AD22103 is used determines two performance traits: the effect of self-heating on accuracy and the response time of the sensor to rapid changes in temperature. In the first case, a rise in the IC junction temperature above the ambient temperature is a function of two variables; the power consumption of the AD22103 and the thermal resistance between the chip and the ambient environment θJA. Selfheating error in degrees Celsius can be derived by multiplying the power dissipation by θJA. Because errors of this type can vary widely for surroundings with different heat sinking capacities, it is necessary to specify θJA under several conditions. Table I shows how the magnitude of self-heating error varies relative to the environment. A typical part will dissipate about 1.5 mW at room temperature with a 3.3 V supply and negligible output loading. In still air, without a “heat sink,” the table below indicates a θJA of 190°C/W, yielding a temperature rise of 0.285°C. Thermal rise will be considerably less in either moving air or with direct physical connection to a solid (or liquid) body. MICROPROCESSOR A/D INTERFACE ISSUES The AD22103 is especially well suited to providing a low cost temperature measurement capability for microprocessor/ microcontroller based systems. Many inexpensive 8-bit microprocessors now offer an onboard 8-bit ADC capability at a modest cost premium. Total “cost of ownership” then becomes a function of the voltage reference and analog signal conditioning necessary to mate the analog sensor with the microprocessor ADC. The AD22103 can provide an ideal low cost system by eliminating the need for a precision voltage reference and any additional active components. The ratiometric nature of the AD22103 allows the microprocessor to use the same power supply as its ADC reference. Variations of hundreds of millivolts in the supply voltage have little effect as both the AD22103 and the ADC use the supply as their reference. The nominal AD22103 signal range of 0.25 V to 3.05 V (0°C to +100°C) makes good use of the input range of a 0 V to 3.3 V ADC. A single resistor and capacitor are recommended to provide immunity to the high speed charge dump glitches seen at many microprocessor ADC inputs (see Figure 1). Table I. Thermal Resistance (TO-92) θJA (°C/Watt) Medium Aluminum Block Moving Air** Without Heat Sink Still Air Without Heat Sink τ (sec)* 60 2 75 3.5 190 15 An 8-bit ADC with a reference of 3.3 V will have a least significant bit (LSB) size of 3.3 V/256 = 12.9 mV. This corresponds to a nominal resolution of about 0.46°C/bit. *The time constant τ is defined as the time to reach 63.2% of the final temperature change. **1200 CFM. USE WITH A PRECISION REFERENCE AS THE SUPPLY VOLTAGE Response of the AD22103 output to abrupt changes in ambient temperature can be modeled by a single time constant τ exponential function. Figure 7 shows typical response time plots for a few media of interest. While the ratiometric nature of the AD22103 allows for system operation without a precision voltage reference, it can still be used in such systems. Overall system requirements involving other sensors or signal inputs may dictate the need for a fixed precision ADC reference. The AD22103 can be converted to absolute voltage operation by using a precision reference as the supply voltage. For example, a 3.3 V reference can be used to power the AD22103 directly. Supply current will typically be 500 µA which is usually within the output capability of the reference. A large number of AD22103s may require an additional op amp buffer, as would scaling down a 10.00 V reference that might be found in “instrumentation” ADCs typically operating from ± 15 V supplies. 100 ALUMINUM BLOCK 90 MOVING AIR % OF FINAL VALUES 80 70 STILL AIR 60 50 40 USING THE AD22103 WITH ALTERNATIVE SUPPLY VOLTAGES 30 20 Because of its ratiometric nature the AD22103 can be used at other supply voltages. Its nominal transfer function can be recalculated based on the new supply voltage. For instance, if using the AD22103 at VS = 5 V the transfer function would be given by: 10 0 0 10 20 30 40 50 60 TIME – sec 70 80 90 100 Figure 7. Response Time The time constant τ is dependent on θJA and the specific heat capacities of the chip and the package. Table I lists the effective τ (time to reach 63.2% of the final value) for a few different media. Copper printed circuit board connections were REV. 0 –5– VO = VS  28 mV 5V 0.25 V + × T A  3.3 V °C 5V  VO = VS  42.42 mV 0.378 V + × T A  5V  °C AD22103 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). TO-92 C2006–18–3/95 0.205 (5.20) 0.175 (4.96) 0.135 (3.43) MIN 0.210 (5.33) 0.170 (4.38) 0.050 (1.27) MAX SEATING PLANE 0.019 (0.482) 0.016 (0.407) SQUARE 0.500 (12.70) MIN 0.055 (1.39) 0.045 (1.15) 0.105 (2.66) 0.095 (2.42) 0.105 (2.66) 0.080 (2.42) 0.105 (2.66) 0.080 (2.42) 1 2 3 0.165 (4.19) 0.125 (3.94) BOTTOM VIEW SO-8 (SOIC) 0.1968 (5.00) 0.1890 (4.80) 8 5 0.2440 (6.20) 0.2284 (5.80) 0.1574 (4.00) 0.1497 (3.80) 1 4 PIN 1 0.0688 (1.75) 0.0532 (1.35) 0.0098 (0.25) 0.0040 (0.10) 0.0500 0.0192 (0.49) (1.27) 0.0138 (0.35) 0.0098 (0.25) BSC 0.0075 (0.19) 8° 0° 0.0500 (1.27) 0.0160 (0.41) PRINTED IN U.S.A. SEATING PLANE 0.0196 (0.50) x 45° 0.0099 (0.25) –6– REV. 0