a
FEATURES
8-Bit CMOS DAC with Output Amplifiers
Operates with Single or Dual Supplies
Low Total Unadjusted Error:
Less Than 1 LSB Over Temperature
Extended Temperature Range Operation
mP-Compatible with Double Buffered Inputs
Standard 18-Pin DIPs, and 20-Terminal Surface
Mount Package and SOIC Package
LC2MOS
8-Bit DAC with Output Amplifiers
AD7224
FUNCTIONAL BLOCK DIAGRAM
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The AD7224 is a precision 8-bit voltage-output, digital-toanalog converter, with output amplifier and double buffered
interface logic on a monolithic CMOS chip. No external trims
are required to achieve full specified performance for the part.
1. DAC and Amplifier on CMOS Chip
The single-chip design of the 8-bit DAC and output amplifier
is inherently more reliable than multi-chip designs. CMOS
fabrication means low power consumption (35 mW typical
with single supply).
The double buffered interface logic consists of two 8-bit registers–an input register and a DAC register. Only the data held in
the DAC registers determines the analog output of the converter. The double buffering allows simultaneous update in a
system containing multiple AD7224s. Both registers may be
made transparent under control of three external lines, CS, WR
and LDAC. With both registers transparent, the RESET line
functions like a zero override; a useful function for system calibration cycles. All logic inputs are TTL and CMOS (5 V) level
compatible and the control logic is speed compatible with most
8-bit microprocessors.
Specified performance is guaranteed for input reference voltages
from +2 V to +12.5 V when using dual supplies. The part is also
specified for single supply operation using a reference of +10 V.
The output amplifier is capable of developing +10 V across a
2 kΩ load.
The AD7224 is fabricated in an all ion-implanted high speed
Linear Compatible CMOS (LC2MOS) process which has been
specifically developed to allow high speed digital logic circuits
and precision analog circuits to be integrated on the same chip.
2. Low Total Unadjusted Error
The fabrication of the AD7224 on Analog Devices Linear
Compatible CMOS (LC2MOS) process coupled with a novel
DAC switch-pair arrangement, enables an excellent total unadjusted error of less than 1 LSB over the full operating temperature range.
3. Single or Dual Supply Operation
The voltage-mode configuration of the AD7224 allows operation from a single power supply rail. The part can also be operated with dual supplies giving enhanced performance for
some parameters.
4. Versatile Interface Logic
The high speed logic allows direct interfacing to most microprocessors. Additionally, the double buffered interface enables simultaneous update of the AD7224 in multiple DAC
systems. The part also features a zero override function.
REV. B
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 617/329-4700
Fax: 617/326-8703
AD7224–SPECIFICATIONS
DUAL SUPPLY
(VDD = 11.4 V to 16.5 V, VSS = –5 V 6 10%; AGND = DGND = O V; VREF = +2 V to (VDD – 4 V)1 unless otherwise noted.
All specifications TMIN to TMAX unless otherwise noted.)
Parameter
K, B, T
Versions2
L, C, U
Versions2
Units
STATIC PERFORMANCE
Resolution
Total Unadjusted Error
Relative Accuracy
Differential Nonlinearity
Full-Scale Error
Full-Scale Temperature Coefficient
Zero Code Error
Zero Code Error Temperature Coefficient
8
±2
±1
±1
± 3/2
± 20
± 30
± 50
8
±1
± 1/2
±1
±1
± 20
± 20
± 30
Bits
LSB max
LSB max
LSB max
LSB max
ppm/°C max
mV max
µV/°C typ
REFERENCE INPUT
Voltage Range
Input Resistance
Input Capacitance3
2 to (VDD – 4)
8
100
2 to (VDD – 4)
8
100
V min to V max
kΩ min
pF max
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Leakage Current
Input Capacitance3
Input Coding
2.4
0.8
±1
8
Binary
2.4
0.8
±1
8
Binary
V min
V max
µA max
pF max
2.5
2.5
V/µs min
5
7
50
2
5
7
50
2
µs max
µs max
nV secs typ
kΩ min
VREF = +10 V; Settling Time to ± 1/2 LSB
VREF = +10 V; Settling Time to ± 1/2 LSB
VREF = 0 V
VOUT = +10 V
11.4/16.5
4.5/5.5
11.4/16.5
4.5/5.5
V min/V max
V min/V max
For Specified Performance
For Specified Performance
4
6
4
6
mA max
mA max
Outputs Unloaded; VIN = VINL or VINH
Outputs Unloaded; VIN = VINL or VINH
3
5
3
5
mA max
mA max
Outputs Unloaded; VIN = VINL or VINH
Outputs Unloaded; VIN = VINL or VINH
90
90
90
90
ns min
ns min
Chip Select/Load DAC Pulse Width
90
90
90
90
ns min
ns min
Write/Reset Pulse Width
0
0
0
0
ns min
ns min
Chip Select/Load DAC to Write Setup Time
0
0
0
0
ns min
ns min
Chip Select/Load DAC to Write Hold Time
90
90
90
90
ns min
ns min
Data Valid to Write Setup Time
10
10
10
10
ns min
ns min
Data Valid to Write Hold Time
DYNAMIC PERFORMANCE
Voltage Output Slew Rate3
Voltage Output Settling Time3
Positive Full-Scale Change
Negative Full-Scale Change
Digital Feedthrough
Minimum Load Resistance
POWER SUPPLIES
VDD Range
VSS Range
IDD
@ 25°C
TMIN to TMAX
ISS
@ 25°C
TMIN to TMAX
SWITCHING CHARACTERISTICS3, 4
t1
@ 25°C
TMIN to TMAX
t2
@ 25°C
TMIN to TMAX
t3
@ 25°C
TMIN to TMAX
t4
@ 25°C
TMIN to TMAX
t5
@ 25°C
TMIN to TMAX
t6
@ 25°C
TMIN to TMAX
Conditions/Comments
VDD = +15 V ± 5%, VREF = +10 V
Guaranteed Monotonic
VDD = 14 V to 16.5 V, VREF = +10 V
Occurs when DAC is loaded with all 1s.
VIN = 0 V or VDD
NOTES
1
Maximum possible reference voltage.
2
Temperature ranges are as follows:
K, L Versions: –40°C to +85°C
B, C Versions: –40°C to +85°C
T, U Versions: –55°C to +125°C
3
Sample Tested at 25°C by Product Assurance to ensure compliance.
4
Switching characteristics apply for single and dual supply operation.
Specifications subject to change without notice.
–2–
REV. B
AD7224
(VDD = +15 V 6 5%; VSS = AGND = DGND = O V; VREF = +10 V unless otherwise noted.
All specifications TMIN to TMAX unless otherwise noted.)
1
SINGLE SUPPLY
Parameter
K, B, T
Versions2
L, C, U
Versions2
Units
Conditions/Comments
STATIC PERFORMANCE
Resolution
Total Unadjusted Error
Differential Nonlinearity
8
±2
±1
8
±2
±1
Bits
LSB max
LSB max
Guaranteed Monotonic
REFERENCE INPUT
Input Resistance
Input Capacitance3
8
100
8
100
kΩ min
pF max
Occurs when DAC is loaded with all 1s.
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Leakage Current
Input Capacitance3
Input Coding
2.4
0.8
±1
8
Binary
2.4
0.8
±1
8
Binary
V min
V max
µA max
pF max
2
2
V/µs min
5
20
50
2
5
20
50
2
µs max
µs max
nV secs typ
kΩ min
Settling Time to ± 1/2 LSB
Settling Time to ± 1/2 LSB
VREF = 0 V
VOUT = +10 V
14.25/15.75
14.25/15.75
V min/V max
For Specified Performance
4
6
4
6
mA max
mA max
Outputs Unloaded; VIN = VINL or VINH
Outputs Unloaded; VIN = VINL or VINH
90
90
90
90
ns min
ns min
Chip Select/Load DAC Pulse Width
90
90
90
90
ns min
ns min
Write/Reset Pulse Width
0
0
0
0
ns min
ns min
Chip Select/Load DAC to Write Setup Time
0
0
0
0
ns min
ns min
Chip Select/Load DAC to Write Hold Time
90
90
90
90
ns min
ns min
Data Valid to Write Setup Time
10
10
10
10
ns min
ns min
Data Valid to Write Hold Time
DYNAMIC PERFORMANCE
Voltage Output Slew Rate4
Voltage Output Settling Time4
Positive Full-Scale Change
Negative Full-Scale Change
Digital Feedthrough3
Minimum Load Resistance
POWER SUPPLIES
VDD Range
IDD
@ 25°C
TMIN to TMAX
SWITCHING CHARACTERISTICS3, 4
t1
@ 25°C
TMIN to TMAX
t2
@ 25°C
TMIN to TMAX
t3
@ 25°C
TMIN to TMAX
t4
@ 25°C
TMIN to TMAX
t5
@ 25°C
TMIN to TMAX
t6
@ 25°C
TMIN to TMAX
NOTES
1
Maximum possible reference voltage.
2
Temperature ranges are as follows:
AD7224KN, LN: 0°C to +70°C
AD7224BQ, CQ: –25°C to +85°C
AD7224TD, UD: –55°C to +125°C
3
See Terminology.
4
Sample tested at 25°C by Product Assurance to ensure compliance.
Specifications subject to change without notice.
REV. B
–3–
VIN = 0 V or VDD
AD7224
ABSOLUTE MAXIMUM RATINGS 1
ORDERING GUIDE
VDD to AGND . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V, +17 V
VDD to DGND . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V, +17 V
VDD to VSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V, +24 V
AGND to DGND . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V, VDD
Digital Input Voltage to DGND . . . . . . . –0.3 V, VDD + 0.3 V
VREF to AGND . . . . . . . . . . . . . . . . . . . . –0.3 V, VDD + 0.3 V
VOUT to AGND2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . VSS, VDD
Power Dissipation (Any Package) to +75°C . . . . . . . . 450 mW
Derates above 75°C by . . . . . . . . . . . . . . . . . . . . . 6 mW/°C
Operating Temperature
Commercial (K, L Versions) . . . . . . . . . . . –40°C to +85°C
Industrial (B, C Versions) . . . . . . . . . . . . . –40°C to +85°C
Extended (T, U Versions) . . . . . . . . . . . . –55°C to +125°C
Storage Temperature . . . . . . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (Soldering, 10 secs) . . . . . . . . . . . +300°C
NOTES
1
Stresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in
the operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
2
The outputs may be shorted to AGND provided that the power dissipation of the
package is not exceeded. Typically short circuit current to AGND is 60 mA.
Model1
Temperature
Range
Total
Unadjusted
Error (LSB)
Package
Option2
AD7224KN
AD7224LN
AD7224KP
AD7224LP
AD7224KR-1
AD7224LR-1
AD7224KR-18
AD7224LR-18
AD7224BQ
AD7224CQ
AD7224TQ
AD7224UQ
AD7224TE
AD7224UE
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–55°C to +125°C
–55°C to +125°C
–55°C to +125°C
–55°C to +125°C
± 2 max
± 1 max
± 2 max
± 1 max
± 2 max
± 1 max
± 2 max
± 1 max
± 2 max
± 1 max
± 2 max
± 1 max
± 2 max
± 1 max
N-18
N-18
P-20A
P-20A
R-20
R-20
R-18
R-18
Q-18
Q-18
Q-18
Q-18
E-20A
E-20A
NOTES
1
To order MIL-STD-883 processed parts, add /883B to part number.
Contact your local sales office for military data sheet.
2
E = Leadless Ceramic Chip Carrier; N = Plastic DIP;
P = Plastic Leaded Chip Carrier; Q = Cerdip; R = SOIC.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD7224 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
PIN CONFIGURATIONS
DIP and SOIC
(SOIC)
VSS
1
18
VDD
VOUT
2
17
RESET
(SOIC)
VSS
1
18
VDD
VOUT
2
17
RESET
VSS
1
20
VOUT
2
19 RESET
VDD
VREF
3
16 LDAC
VREF
3
AGND
4
15
WR
AGND
4
DGND
5
CS
DGND
5
(MSB) DB7
6
14
TOP VIEW
(Not to Scale)
13
(MSB) DB7
6
DB6
7
12 DB1
DB6
7
12 DB1
DB6
7
14 DB1
DB5
8
11 DB2
DB5
8
11 DB2
DB5
8
13 DB2
DB4
9
10 DB3
DB4
9
10 DB3
DB4
9
12 DB3
AD7224
DB0 (LSB)
16 LDAC
VREF
3
15
WR
AGND
4
14
TOP VIEW
(Not to Scale)
13
CS
DGND
5
(MSB) DB7
6
AD7224
R-18
18 LDAC
AD7224
R-20
DB0 (LSB)
16 CS
TOP VIEW
(Not to Scale) 15 DB0 (LSB)
NC 10
VDD
RESET
NC
1
20 19
VREF
4
AD7224
AGND
5
AD7224
17 WR
TOP VIEW
(Not to Scale)
16 CS
DGND
6
16 CS
(MSB) DB7
7
TOP VIEW
(Not to Scale)
DB6
8
NC = NO CONNECT
15 DB0 (LSB)
14 DB1
10 11 12 13
DB2
9
NC
DB2
NC
10 11 12 13
DB3
9
DB4
14 DB1
DB5
DB6 8
DB3
15 DB0 (LSB)
18 LDAC
DB4
18 LDAC
(MSB) DB7 7
2
DB5
DGND 6
3
11 NC
NC = NO CONNECT
17 WR
VREF 4
AGND 5
VOUT
NC
1 20 19
VDD
VOUT
VSS
2
VSS
PLCC
RESET
LCCC
3
17 WR
NC = NO CONNECT
–4–
REV. B
AD7224
VOUT = D • VREF
TERMINOLOGY
TOTAL UNADJUSTED ERROR
Total Unadjusted Error is a comprehensive specification which
includes full-scale error, relative accuracy and zero code error.
Maximum output voltage is VREF – 1 LSB (ideal), where 1 LSB
(ideal) is VREF/256. The LSB size will vary over the VREF range.
Hence the zero code error, relative to the LSB size, will increase
as VREF decreases. Accordingly, the total unadjusted error,
which includes the zero code error, will also vary in terms of
LSBs over the VREF range. As a result, total unadjusted error is
specified for a fixed reference voltage of +10 V.
RELATIVE ACCURACY
Relative Accuracy or endpoint nonlinearity is a measure of the
maximum deviation from a straight line passing through the
endpoints of the DAC transfer function. It is measured after allowing for zero code error and full-scale error and is normally
expressed in LSBs or as a percentage of full-scale reading.
where D is a fractional representation of the digital input code
and can vary from 0 to 255/256.
OP-AMP SECTION
The voltage-mode D/A converter output is buffered by a unity
gain noninverting CMOS amplifier. This buffer amplifier is
capable of developing +10 V across a 2 kΩ load and can drive
capacitive loads of 3300 pF.
The AD7224 can be operated single or dual supply resulting in
different performance in some parameters from the output amplifier. In single supply operation (VSS = 0 V = AGND) the sink
capability of the amplifier, which is normally 400 µA, is reduced
as the output voltage nears AGND. The full sink capability of
400 µA is maintained over the full output voltage range by tying
VSS to –5 V. This is indicated in Figure 2.
500
DIFFERENTIAL NONLINEARITY
VSS = –5V
Differential Nonlinearity is the difference between the measured
change and the ideal 1 LSB change between any two adjacent
codes. A specified differential nonlinearity of ± 1 LSB max over
the operating temperature range ensures monotonicity.
ISINK – µA
400
DIGITAL FEEDTHROUGH
Digital Feedthrough is the glitch impulse transferred to the output due to a change in the digital input code. It is specified in
nV secs and is measured at VREF = 0 V.
0
0
Full-Scale Error is defined as:
Measured Value – Zero Code Error – Ideal Value
D/A SECTION
The AD7224 contains an 8-bit voltage-mode digital-to-analog
converter. The output voltage from the converter has the same
polarity as the reference voltage, allowing single supply operation. A novel DAC switch pair arrangement on the AD7224 allows a reference voltage range from +2 V to +12.5 V.
The DAC consists of a highly stable, thin-film, R-2R ladder and
eight high speed NMOS single pole, double-throw switches.
The simplified circuit diagram for this DAC is shown in
Figure 1.
VREF
R
R
VOUT
2R
2R
2R
2R
DB0
DB0
DB0
DB0
SHOWN FOR ALL 1's ON DAC
AGND
Figure 1. D/A Simplified Circuit Diagram
The input impedance at the VREF pin is code dependent and can
vary from 8 kΩ minimum to infinity. The lowest input impedance occurs when the DAC is loaded with the digital code
01010101. Therefore, it is important that the reference presents
a low output impedance under changing load conditions. The
nodal capacitance at the reference terminals is also code dependent and typically varies from 25 pF to 50 pF.
The VOUT pin can be considered as a digitally programmable
voltage source with an output voltage of:
REV. B
2
4
6
VOUT – Volts
8
10
Figure 2. Variation of ISINK with VOUT
CIRCUIT INFORMATION
2R
VDD = +15V
TA = 25°C
VSS = 0V
200
100
FULL-SCALE ERROR
R
300
Settling-time for negative-going output signals approaching
AGND is similarly affected by VSS. Negative-going settling-time
for single supply operation is longer than for dual supply operation. Positive-going settling-time is not affected by VSS.
Additionally, the negative VSS gives more headroom to the output amplifier which results in better zero code performance and
improved slew-rate at the output, than can be obtained in the
single supply mode.
DIGITAL SECTION
The AD7224 digital inputs are compatible with either TTL or
5 V CMOS levels. All logic inputs are static-protected MOS
gates with typical input currents of less than 1 nA. Internal input protection is achieved by an on-chip distributed diode between DGND and each MOS gate. To minimize power supply
currents, it is recommended that the digital input voltages be
driven as close to the supply rails (VDD and DGND) as practically possible.
INTERFACE LOGIC INFORMATION
Table I shows the truth table for AD7224 operation. The part
contains two registers, an input register and a DAC register. CS
and WR control the loading of the input register while LDAC
and WR control the transfer of information from the input register to the DAC register. Only the data held in the DAC register
will determine the analog output of the converter.
All control signals are level-triggered and therefore either or
both registers may be made transparent; the input register by
keeping CS and WR “LOW”, the DAC register by keeping
LDAC and WR “LOW”. Input data is latched on the rising
edge of WR.
–5–
AD7224
a +2.5 V bandgap reference and the AD584, a precision +10 V
reference. Note that in order to achieve an output voltage range
of 0 V to +10 V, a nominal +15 V ± 5% power supply voltage is
required by the AD7224.
Table I. AD7224 Truth Table
RESET LDAC
WR
CS
Function
H
H
H
H
H
H
H
L
L
X
H
H
H
L
L
X
L
H
X
L
X
L
X
H
L
L
H
H
X
g
H
H
H
g
L
L
L
Both Registers are Transparent
Both Registers are Latched
Both Registers are Latched
Input Register Transparent
Input Register Latched
DAC Register Transparent
DAC Register Latched
Both Registers Loaded
With All Zeros
Both Register Latched With All Zeros
and Output Remains at Zero
Both Registers are Transparent and
Output Follows Input Data
g
L
g
GROUND MANAGEMENT
AC or transient voltages between AGND and DGND can cause
noise at the analog output. This is especially true in microprocessor systems where digital noise is prevalent. The simplest
method of ensuring that voltages at AGND and DGND are
equal is to tie AGND and DGND together at the AD7224. In
more complex systems where the AGND and DGND intertie is
on the backplane, it is recommended that two diodes be connected in inverse parallel between the AD7224 AGND and
DGND pins (IN914 or equivalent).
H = High State, L = Low State, X = Don’t Care.
All control inputs are level triggered.
Applying the AD7224
The contents of both registers are reset by a low level on the
RESET line. With both registers transparent, the RESET line
functions like a zero override with the output brought to 0 V for
the duration of the RESET pulse. If both registers are latched, a
“LOW” pulse on RESET will latch all 0s into the registers and
the output remains at 0 V after the RESET line has returned
“HIGH”. The RESET line can be used to ensure power-up to
0 V on the AD7224 output and is also useful, when used as a
zero override, in system calibration cycles. Figure 3 shows the
input control logic for the AD7224.
LDAC
UNIPOLAR OUTPUT OPERATION
This is the basic mode of operation for the AD7224, with the
output voltage having the same positive polarity as VREF. The
AD7224 can be operated single supply (VSS = AGND) or with
positive/negative supplies (see op-amp section which outlines
the advantages of having negative VSS). Connections for the unipolar output operation are shown in Figure 5. The voltage at
VREF must never be negative with respect to DGND. Failure to
observe this precaution may cause parasitic transistor action and
possible device destruction. The code table for unipolar output
operation is shown in Table II.
DAC
REGISTER
VREF
WR
INPUT
REGISTER
CS
VDD
3
DB7
DATA
(8-BIT)
RESET
INPUT DATA
DB0
CS
Figure 3. Input Control Logic
VOUT
DAC
WR
t1
CS
t3
WR
t4
t2
t2
t3
LDAC
t5
DATA
IN
AD7224
LDAC
RESET
t6
t1
VSS
AGND
DGND
t4
Figure 5. Unipolar Output Circuit
DATA
VALID
Table III. Unipolar Code Table
NOTES:
1. ALL INPUT SIGNAL RISE AND FALL TIMES MEASURED FROM 10% TO 90% OF VDD .
t r = tf = 20ns OVER V DD RANGE
VINH + V INL
2. TIMING MEASUREMENT REFERENCE LEVEL IS
2
DAC Register Contents
MSB
LSB
Figure 4. Write Cycle Timing Diagram
SPECIFICATION RANGES
For the DAC to maintain specified accuracy, the reference voltage must be at least 4 V below the VDD power supply voltage.
This voltage differential is required for correct generation of bias
voltages for the DAC switches.
With dual supply operation, the AD7224 has an extended VDD
range from +12 V ± 5% to +15 V ± 10% (i.e., from +11.4 V to
+16.5 V). Operation is also specified for a single VDD power
supply of +15 V ± 5%.
Performance is specified over a wide range of reference voltages
from 2 V to (VDD – 4 V) with dual supplies. This allows a range
of standard reference generators to be used such as the AD580,
Analog Output
1111
1111
255
+V REF
256
1000
0001
129
+V REF
256
1000
0000
128
V REF
+V REF
=+ 2
256
0111
1111
127
+V REF
256
0000
0001
1
+V REF
256
0000
0000
0V
( )
1
Note: 1 LSB = (V REF ) 2−8 = V REF
256
–6–
REV. B
AD7224
BIPOLAR OUTPUT OPERATION
VIN
The AD7224 can be configured to provide bipolar output operation using one external amplifier and two resistors. Figure 6
shows a circuit used to implement offset binary coding. In this
case
VREF
VDD
VOUT
AGND
DAC
VIN
R2
R2
V O = 1 +
• ( D V REF ) –
• (V REF )
R1
R1
AD7224
VBIAS
With R1 = R2
VSS
VO = (2 D – 1) • VREF
where D is a fractional representation of the digital word in
the DAC register.
Mismatch between R1 and R2 causes gain and offset errors;
therefore, these resistors must match and track over temperature. Once again, the AD7224 can be operated in single supply
or from positive/negative supplies. Table III shows the digital
code versus output voltage relationship for the circuit of Figure
6 with R1 = R2.
DGND
Figure 7. AGND Bias Circuit
MICROPROCESSOR INTERFACE
A15
ADDRESS BUS
A8
ADDRESS
DECODE
8085A
8088
CS
LDAC
AD7224*
WR
VREF
VREF
VDD
R1
3
DB7
DATA
(8-BIT)
R2
ALE
+15V
AD7
AD0
LATCH
EN
DB7
DB0
ADDRESS DATA BUS
*LINEAR CIRCUITRY OMITTED FOR CLARITY
VOUT
DB0
CS
WR
DAC
VOUT
WR
AD7224
LDAC
Figure 8. AD7224 to 8085A/8088 Interface
+15V
A15
R1, R2 = 10kΩ ±0.1%
RESET
ADDRESS BUS
A0
VSS
AGND
DGND
6809
6502
R/W
ADDRESS
DECODE
CS
LDAC
EN
AD7224*
Figure 6. Bipolar Output Circuit
Table III. Bipolar (Offset Binary) Code Table
DAC Register Contents
MSB
LSB
1111
1111
1000
0001
E OR φ2
WR
D7
E OR φ2
D0
DB7
DB0
D7
D0
Analog Output
DATA BUS
*LINEAR CIRCUITRY OMITTED FOR CLARITY
127
+V REF
128
1
+V REF
128
Figure 9. AD7224 to 6809/6502 Interface
A15
ADDRESS BUS
A0
1000
0000
0V
CS
Z-80
0111
0000
0000
1111
0001
0000
1
–V REF
128
127
–V REF
128
128
–V REF
= –V REF
128
LDAC
AD7224*
WR
WR
DB7
DB0
D7
D0
DATA BUS
*LINEAR CIRCUITRY OMITTED FOR CLARITY
Figure 10. AD7224 to Z-80 Interface
AGND BIAS
The AD7224 AGND pin can be biased above system GND
(AD7224 DGND) to provide an offset “zero” analog output
voltage level. Figure 7 shows a circuit configuration to achieve
this. The output voltage, VOUT, is expressed as:
VOUT = VBIAS + D • (VIN)
where D is a fractional representation of the digital word in
DAC register and can vary from 0 to 255/256.
A23
ADDRESS BUS
A1
68008
ADDRESS
DECODE
R/W
CS
LDAC
WR
AD7224*
DTACK
DB7
DB0
D7
For a given VIN, increasing AGND above system GND will reduce the effective VDD–VREF which must be at least 4 V to ensure specified operation. Note that VDD and VSS for the AD7224
must be referenced to DGND.
REV. B
ADDRESS
DECODE
D0
DATA BUS
*LINEAR CIRCUITRY OMITTED FOR CLARITY
Figure 11. AD7224 to 68008 Interface
–7–
AD7224
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
18-Pin Cerdip (Suffix Q)
18-Pin Ceramic (Suffix D)
18-Lead SOIC
(R-18)
C836a–10–10/84
18-Pin Plastic (Suffix N)
18
10
0.2992 (7.60)
0.2914 (7.40)
0.4193 (10.65)
0.3937 (10.00)
PIN 1
9
1
0.1043 (2.65)
0.0926 (2.35)
0.4625 (11.75)
0.4469 (11.35)
PLCC Package
P-20A
0.048 (1.21)
0.042 (1.07)
0.056 (1.42)
0.042 (1.07)
3
0.050
(1.27)
BSC
0.025 (0.63)
0.015 (0.38)
0.032 (0.81)
0.026 (0.66)
20
14
0.0500 (1.27)
0.0157 (0.40)
11
13
0.2992 (7.60)
0.2914 (7.40)
0.040 (1.01)
0.025 (0.64)
0.356 (9.04)
SQ
0.350 (8.89)
0.110 (2.79)
0.085 (2.16)
0.395 (10.02)
SQ
0.385 (9.78)
0.4193 (10.65)
0.3937 (10.00)
PIN 1
1
10
LCCC Package
E-20A
0.075
(1.91)
REF
0.100 (2.54)
0.064 (1.63)
0.358 (9.09)
0.342 (8.69)
SQ
0.358
(9.09)
MAX
SQ
8°
0°
0.330 (8.38)
0.290 (7.37)
8
9
0.0125 (0.32)
0.0091 (0.23)
20-Lead SOIC
(R-20)
0.021 (0.53)
0.013 (0.33)
18
TOP VIEW
0.020
(0.50)
R
0.0192 (0.49)
0.0138 (0.35)
19
PIN 1
IDENTIFIER
4
0.0500
(1.27)
BSC
0.095 (2.41)
0.075 (1.90)
0.1043 (2.65)
0.0926 (2.35)
0.5118 (13.00)
0.4961 (12.60)
0.200 (5.08)
BSC
0.100
(2.54)
BSC
0.015 (0.38)
MIN
0.0118 (0.30)
0.0040 (0.10)
0.028 (0.71)
0.022 (0.56)
20
PRINTED IN U.S.A.
0.048 (1.21)
0.042 (1.07)
0.0118 (0.30)
0.0040 (0.10)
0.180 (4.57)
0.165 (4.19)
0.0291 (0.74)
x 45 °
0.0098 (0.25)
0.0500
(1.27)
BSC
0.0192 (0.49)
0.0138 (0.35)
0.0125 (0.32)
0.0091 (0.23)
0.0291 (0.74)
x 45 °
0.0098 (0.25)
8°
0°
0.0500 (1.27)
0.0157 (0.40)
1
0.011 (0.28)
0.007 (0.18)
R TYP
0.075
(1.91)
REF
0.088 (2.24)
0.054 (1.37)
BOTTOM
VIEW
13
0.055 (1.40)
0.045 (1.14)
9
0.150
(3.81)
BSC
0.050
(1.27)
BSC
45 °
TYP
–8–
REV. B
工商网监
湘ICP备2023018690号
