AD7262BCPZ-RL7

FEATURES FUNCTIONAL BLOCK DIAGRAM Dual simultaneous sampling 12-bit, 2-channel analog-todigital converter (ADC) True differential analog inputs Programmable gain stage: ×1, ×2, ×3, ×4, ×6, ×8, ×12, ×16, ×24, ×32, ×48, ×64, ×96, ×128 Throughput rate per ADC 1 MSPS for AD7262 500 kSPS for AD7262-5 Analog input impedance: >1 GΩ Wide input bandwidth −3 dB bandwidth: 1.7 MHz at gain = 2 4 on-chip comparators SNR: 73 dB typical at gain = 2, 66 dB typical at gain = 32 Device offset calibration, system gain calibration On-chip reference: 2.5 V −40°C to +105°C operation High speed serial interface SPI/QSPI™/MICROWIRE/DSP compatible 48-lead LFCSP and LQFP REF VA+ VA – VB+ VB – The AD7262/AD7262-5 are ideally suited for monitoring small amplitude signals from a variety of sensors. They include all the functionality needed for monitoring the position feedback signals from a variety of analog encoders used in motor control systems. Rev. C PGA 12-BIT SUCCESSIVE APPROXIMATION ADC T/H OUTPUT DRIVERS PGA 12-BIT SUCCESSIVE APPROXIMATION ADC T/H DOUTA SCLK CAL CS REFSEL G0 G1 G2 G3 VDRIVE OUTPUT DRIVERS BUF DOUTB PD0/DIN PD1 PD2 VREF B CA_CBVCC C A+ CA – The AD7262/AD7262-5 contain four comparators. Comparator A and Comparator B are optimized for low power, while Comparator C and Comparator D have fast propagation delays. The AD7262/AD7262-5 feature a calibration function to remove any device offset error and programmable gain adjust registers to allow for input path (for example, sensor) offset and gain compensation. The AD7262/AD7262-5 have an on-chip 2.5 V reference that can be disabled if an external reference is preferred. AD7262 BUF CONTROL LOGIC GENERAL DESCRIPTION The AD7262/AD7262-5 are dual, 12-bit, high speed, low power, successive approximation ADCs that operate from a single 5 V power supply. The AD7262 features throughput rates of up to 1 MSPS per on-chip ADC. The AD7262-5 features throughput rates of up to 500 kSPS. Two complete ADC functions allow simultaneous sampling and conversion of two channels. Each ADC is preceded by a true differential analog input with a PGA. There are 14 gain settings available: ×1, ×2, ×3, ×4, ×6, ×8, ×12, ×16, ×24, ×32, ×48, ×64, ×96, and ×128. VREF A AVCC C B+ COMP CB – CA_CB_GND COMP CC_CDVCC C C+ CC – C D+ CD – CC_CD_GND OUTPUT DRIVERS COMP COUTA OUTPUT DRIVERS OUTPUT DRIVERS COMP AGND COUTB COUTC OUTPUT DRIVERS COUTD DGND Figure 1. PRODUCT HIGHLIGHTS 1. 2. 3. 4. Integrated PGA with a variety of flexible gain settings to allow detection and conversion of low level analog signals. Each PGA is followed by a dual simultaneous sampling ADC, featuring throughput rates of 1 MSPS per ADC for the AD7262. The conversion results of both ADCs are simultaneously available on separate data lines or in succession on one data line if only one serial port is available. Four integrated comparators that can be used to count signals from pole sensors in motor control applications. Internal 2.5 V reference. Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2008–2018 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com 07606-001 Data Sheet 1 MSPS, 12-Bit, Simultaneous Sampling SAR ADC with PGA and Four Comparators AD7262 AD7262 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Application Details ..................................................................... 20 General Description ......................................................................... 1 Modes of Operation ....................................................................... 22 Functional Block Diagram .............................................................. 1 Pin-Driven Mode ....................................................................... 22 Product Highlights ........................................................................... 1 Gain Selection ............................................................................. 22 Revision History ............................................................................... 2 Power-Down Modes .................................................................. 22 Specifications..................................................................................... 3 Control Register ......................................................................... 23 Timing Specifications .................................................................. 6 On-Chip Registers ...................................................................... 24 Timing Diagram ........................................................................... 6 Serial Interface ................................................................................ 25 Absolute Maximum Ratings ............................................................ 7 Calibration ....................................................................................... 27 ESD Caution .................................................................................. 7 Internal Offset Calibration ........................................................ 27 Pin Configurations and Function Descriptions ........................... 8 Adjusting the Offset Calibration Registers ................................. 28 Typical Performance Characteristics ........................................... 10 System Gain Calibration............................................................ 28 Terminology .................................................................................... 14 Microprocessor Interfacing ........................................................... 29 Theory of Operation ...................................................................... 15 AD7262/AD7262-5 to ADSP-BF531 ....................................... 29 Circuit Information .................................................................... 15 Application Hints ........................................................................... 30 Comparators................................................................................ 15 Grounding and Layout .............................................................. 30 Operation..................................................................................... 15 PCB Design Guidelines for LFCSP .......................................... 30 Analog Inputs .............................................................................. 15 Outline Dimensions ....................................................................... 31 VDRIVE ............................................................................................ 16 Ordering Guide .......................................................................... 31 Reference ..................................................................................... 17 Typical Connection Diagrams .................................................. 17 REVISION HISTORY 1/2018—Rev. B to Rev. C Changed CP-48-4 to CP-48-1 ...................................... Throughout Updated Outline Dimensions ....................................................... 31 Changes to Ordering Guide .......................................................... 31 11/2016—Rev. A to Rev. B Change to Figure 4 ........................................................................... 8 Change to Pin 31, 32 Description, Table 4 .................................... 9 Changes to Serial Interface Section .............................................. 25 Changes to Figure 34 and Figure 34 Caption ............................. 26 Updated Outline Dimensions ....................................................... 31 Changes to Ordering Guide .......................................................... 31 8/2015—Rev. 0 to Rev. A Changed ADSP-BF53x to ADSP-BF531 ..................... Throughout Changes to Table 4.............................................................................9 Change to Serial Interface Section ............................................... 25 Changes to Figure 34 and Figure 34 Caption ............................. 26 Change to Microprocessor Interfacing Section and Figure 37 . 29 Changes to AD7262/AD7262-5 to ADSP-BF531 Section......... 29 Updated Outline Dimensions ....................................................... 31 7/2008—Revision 0: Initial Version Rev. C | Page 2 of 32 Data Sheet AD7262 SPECIFICATIONS AVCC = 4.75 V to 5.25 V, CA_CBVCC = CC_CDVCC = 2.7 V to 5.25 V, VDRIVE = 2.7 V to 5.25 V, fSAMPLE = 1 MSPS and fSCLK = 40 MHz for AD7262, fSAMPLE = 500 kSPS and fSCLK = 20 MHz for AD7262-5, VREF = 2.5 V internal/external; TA = −40°C to +105°C, unless otherwise noted. Table 1. Parameter DYNAMIC PERFORMANCE 1 Signal-to-Noise Ratio (SNR) 2 Signal-to-(Noise + Distortion) Ratio (SINAD)2 Total Harmonic Distortion (THD)2 Spurious-Free Dynamic Range (SFDR)2 Common-Mode Rejection Ratio (CMRR) 3 Min Typ 70 70 73 72 ±0.5 ±0.5 ±0.122 ±0.018 ±0.061 ±0.092 ±0.012 ±0.061 ±0.122 ±0.018 ±0.061 2.5 Positive Full-Scale Error Match Zero Code Error2 Zero Code Error Match Negative Full-Scale Error2 Negative Full-Scale Error Match Zero Code Error Drift ANALOG INPUT Input Voltage Range, VIN+ and VIN− Common-Mode Voltage Range, VCM DC Leakage Current Input Capacitance3 Input Impedance3 REFERENCE INPUT/OUTPUT Reference Output Voltage 5 Reference Input Voltage Range DC Leakage Current Input Capacitance3 VREFA, VREFB Output Impedance3 Reference Temperature Coefficient VREF Noise3 −77 −90 1.2 1.7 DC ACCURACY Resolution Integral Nonlinearity2 Differential Nonlinearity2 Positive Full-Scale Error2 VCM ± Unit dB dB −85 −97 −76 ADC-to-ADC Isolation3 Bandwidth3 Max dB dB dB dB MHz MHz 12 ±1 ±0.99 ±0.305 ±0.244 ±0.305 VREF 2 × Gain Bits LSB LSB % FSR % FSR % FSR % FSR % FSR % FSR % FSR % FSR % FSR µV/°C (VCC/2) − 0.4 (VCC/2) − 0.4 (VCC/2) − 0.6 (VCC/2) + 0.2 (VCC/2) + 0.4 (VCC/2) + 0.8 ±1 V V V µA pF GΩ 2.505 V V µA ±1 20 4 20 20 Rev. C | Page 3 of 32 Guaranteed no missed codes to 12 bits Pregain calibration Postgain calibration Preoffset and pregain calibration Postoffset and postgain calibration Pregain calibration Postgain calibration VCM = 2; PGA gain setting = 1; see Figure 19 4 VCM = AVCC/2; PGA gain setting = 2 VCM = AVCC/2; 3 ≤ PGA gain setting ≤ 32 VCM = AVCC/2; PGA gain setting ≥ 48 V 2.5 2.5 ±0.3 @ −3 dB; PGA gain setting = 128 @ −3 dB; PGA gain setting = 2 VCM = AVCC/2; PGA gain setting ≥ 2 VCM + 100 mV 2.495 For PGA gain setting = 2, ripple frequency of 50 Hz/60 Hz; see Figure 17 and Figure 18 V VCM − 100 mV ±0.001 5 1 Test Conditions/Comments fIN = 100 kHz sine wave PGA gain setting = 2 pF Ω ppm/°C µV rms 2.5 V ± 5 mV max @ 25°C External reference applied to Pin VREFA/Pin VREFB AD7262 Parameter LOGIC INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current, IIN Input Capacitance, CIN3 LOGIC OUTPUTS Output High Voltage, VOH Output Low Voltage, VOL Floating State Leakage Current Floating State Output Capacitance3 Output Coding CONVERSION RATE Conversion Time Track-and-Hold Acquisition Time Throughput Rate COMPARATORS Input Offset Comparator A and Comparator B Comparator C and Comparator D Offset Voltage Drift Input Common-Mode Range3 Input Capacitance3 Input Impedance3 IDD Normal Mode (Static) 6 Comparator A and Comparator B Comparator C and Comparator D Data Sheet Min Typ Max Unit 0.8 ±1 V V µA pF 0.4 ±1 V V µA pF 0.7 × VDRIVE 4 VDRIVE − 0.2 5 Twos complement 19 × tSCLK 400 1 500 ±2 ±2 0.5 0 to 4 0 to 1.7 4 1 3 6 60 120 ±4 ±4 8.5 170 ns ns MSPS kSPS mV mV μV/°C V V pF GΩ Comparator C and Comparator D Low to High, tPLH Comparator A and Comparator B Comparator C and Comparator D 1.4 0.95 0.20 0.13 3.5 2 0.93 0.18 0.12 4 0.32 0.28 ±250 ±10 Rev. C | Page 4 of 32 AD7262 AD7262-5 TA = 25°C to 105°C only All comparators CA_CBVCC = 5 V CA_CBVCC = 2.7 V µA µA µA µA µs µs µs µs CA_CBVCC = 2.7 V CA_CBVCC = 5 V CC_CDVCC = 2.7 V CC_CDVCC = 5 V µs µs µs µs CA_CBVCC = 2.7 V CA_CBVCC = 5 V CC_CDVCC = 2.7 V CC_CDVCC = 5 V VCM = AVCC 2, VOVERDRIVE = 200 mV differential Delay Matching Comparator A and Comparator B Comparator C and Comparator D VIN = 0 V or VDRIVE 25 pF load, COUTx = 0 V, VCM = AVCC/2, VOVERDRIVE = 200 mV differential CA_CBVCC = 3.3 V CA_CBVCC = 5.25 V CC_CDVCC = 3.3 V CC_CDVCC = 5.25 V VCM = AVCC/2, VOVERDRIVE = 200 mV differential Propagation Delay Time High to Low, tPHL Comparator A and Comparator B Test Conditions/Comments ns ns Data Sheet Parameter POWER REQUIREMENTS AVCC CA_CBVCC, CC_CDVCC VDRIVE IDD ADC Normal Mode (Static) ADC Normal Mode (Dynamic) Shutdown Mode Power Dissipation ADC Normal Mode (Static) ADC Normal Mode (Dynamic) Shutdown Mode AD7262 Min Typ Max Unit 5.25 5.25 5.25 V V V 20 23 0.5 31.5 33.3 1 mA mA μA 105 120 2.625 165 175 5.25 mW mW µW 4.75 2.7 2.7 Test Conditions/Comments Digital inputs = 0 V or VDRIVE AVCC = 5.25 V AVCC = 5.25 V AVCC = 5.25 V, ADCs and comparators powered down These specifications were determined without the use of the gain calibration feature. See the Terminology section. Samples tested during initial release to ensure compliance; they are not subject to production testing. 4 For PGA gain = 1; to use the full analog input range (VCM ± VREF/2) of the AD7262, the VCM voltage should be dropped to lie within a range from 1.95 V to 2.05 V. 5 Refers to Pin VREFA or Pin VREFB. 6 This specification includes the IDD for both comparators. The IDD per comparator is the specified value divided by two. 1 2 3 Rev. C | Page 5 of 32 AD7262 Data Sheet TIMING SPECIFICATIONS AVCC = 4.75 V to 5.25 V, CA_CBVCC = CC_CDVCC = 2.7 V to 5.25 V, VREF = 2.5 V internal/external; TA = TMIN to TMAX, unless otherwise noted.1 Table 2. tQUIET Limit at TMIN, TMAX 2.7 V ≤ VDRIVE ≤ 3.6 V 4.75 V ≤ VDRIVE ≤ 5.25 V 200 200 40 40 32 32 20 20 19 × tSCLK 19 × tSCLK 475 475 950 950 13 13 Unit kHz min MHz max MHz typ MHz max ns max ns max ns max ns min t2 t33 10 15 10 15 ns min ns max t4 t5 t6 t7 t8 t9 29 15 0.4 × tSCLK 0.4 × tSCLK 13 13 23 13 0.4 × tSCLK 0.4 × tSCLK 13 13 ns max ns min ns min ns min ns min ns max t10 5 35 2 2 5 35 2 2 ns min ns max μs min μs min 3 3 240 15 3 3 240 15 ns min ns min μs max μs max Parameter fSCLK tCONVERT t11 t12 t13 t14 tPOWER-UP Description AD72622 AD72622 AD7262-5 tSCLK = 1/fSCLK AD7262 AD7262-5 Minimum time between end of serial read/bus relinquish and next falling edge of CS CS to SCLK setup time Delay from 19th SCLK falling edge until DOUTA and DOUTB are three-state disabled Data access time after SCLK falling edge SCLK to data valid hold time SCLK high pulse width SCLK low pulse width CS rising edge to falling edge pulse width CS rising edge to DOUTA, DOUTB, high impedance/bus relinquish SCLK falling edge to DOUTA, DOUTB, high impedance SCLK falling edge to DOUTA, DOUTB, high impedance Minimum CAL pin high time Minimum time between the CAL pin high and the CS falling edge DIN setup time prior to SCLK falling edge DIN hold time after SCLK falling edge Internal reference, with a 1 μF decoupling capacitor With an external reference, 10 μs typical 1 Sample tested during initial release to ensure compliance. All input signals are specified with tR = tF = 5 ns (10% to 90% of AVCC) and timed from a voltage level of 1.6 V. All timing specifications given are with a 25 pF load capacitance. With a load capacitance greater than this value, a digital buffer or latch must be used. See the Terminology section. 2 See the Serial Interface section. 3 The time required for the output to cross 0.4 V or 2.4 V. TIMING DIAGRAM CS t8 t2 1 t6 2 3 4 5 18 20 19 t7 t3 DOUTA THREE-STATE DOUTB THREE-STATE 21 29 31 t9 t5 t4 30 DB11 A DB10 A DB9A DB1A DB0A DB11 B DB10 B DB9B DB1B DB0B Figure 2. Serial Interface Timing Diagram Rev. C | Page 6 of 32 tQUIET THREESTATE THREESTATE 07606-002 SCLK Data Sheet AD7262 ABSOLUTE MAXIMUM RATINGS Table 3. Parameter VDRIVE to DGND VDRIVE to AGND AVCC to AGND/DGND CA_CBVCC to CA_CB_GND CC_CDVCC to CC_CD_GND AGND to DGND CA_CB_GND/CC_CD_GND to DGND Analog Input Voltage to AGND Digital Input Voltage to DGND Digital Output Voltage to GND VREFA/VREFB Input to AGND COUTA/COUTB/COUTC/COUTD to GND CA±/CB±/CC±/CD± to CA_CB_GND/CC_CD_GND Operating Temperature Range Storage Temperature Range Junction Temperature LFCSP θJA Thermal Impedance θJC Thermal Impedance LQFP θJA Thermal Impedance θJC Thermal Impedance Pb-Free Temperature, Soldering Reflow ESD Rating −0.3 V to AVCC −0.3 V to AVCC −0.3 V to +7 V −0.3 V to +7 V −0.3 V to +7 V −0.3 V to +0.3 V −0.3 V to +0.3 V −0.3 V to AVCC + 0.3 V −0.3 V to +7 V −0.3 V to VDRIVE + 0.3 V −0.3 V to AVCC + 0.3 V −0.3 V to VDRIVE + 0.3 V −0.3 V to CA_CBVCC/CC_CDVCC + 0.3 V −40°C to +105°C −65°C to +150°C 150°C Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. ESD CAUTION 30°C/W 3°C/W 55°C/W 16°C/W 255°C 2 kV Rev. C | Page 7 of 32 AD7262 Data Sheet TOP VIEW (Not to Scale) CS 34 SCLK 33 AVCC 32 DOUTA 31 DOUTB 30 AGND 8 29 COUTA COUTB VB+ 9 28 DGND 27 VDRIVE 26 COUTC 25 COUTD VB– 10 AVCC 11 CC_CDVCC 12 CA_CBVCC 1 AVCC 2 VA – 3 VA+ 4 AGND 5 AGND 6 AVCC 7 AGND 8 VB+ 9 VB– 10 AVCC 11 CC_CDVCC 12 07606-003 REFSEL PD0/DIN PD1 PD2 AVCC AGND CC_CD_GND VREFB CD– CD+ CC– CC+ 13 14 15 16 17 18 19 20 21 22 23 24 CB– CA_CB_GND VREF A AGND AVCC G0 G1 G2 G3 AD7262 TOP VIEW (Not to Scale) 36 35 34 33 32 31 30 29 28 27 26 25 CAL CS SCLK AV CC DOUTA DOUTB COUTA COUTB DGND VDRIVE COUTC COUTD NOTES 1. THE EXPOSED METAL PADDLE ON THE BOTTOM OF THE LFCSP PACKAGE MUST BE SOLDERED TO PCB GROUND FOR PROPER HEAT DISSIPATION AND ALSO FOR NOISE AND MECHANICAL STRENGTH BENEFITS. Figure 3. 48-Lead LQFP Pin Configuration Figure 4. 48-Lead LFCSP Pin Configuration Table 4. Pin Function Descriptions Pin No. 2, 7, 11, 20, 33, 41 Mnemonic AVCC 1 CA_CBVCC 12 CC_CDVCC 4, 3 9, 10 43, 18 VA+, VA− VB+, VB− VREFA, VREFB 34 SCLK 36 21 CAL PD2 22 PD1 Description Analog Supply Voltage, 4.75 V to 5.25 V. This is the supply voltage for the analog circuitry on the AD7262/AD7262-5. All AVCC pins can be tied together. Decouple this supply to AGND with a 100 nF ceramic capacitor per supply and a 10 μF tantalum capacitor. Comparator Supply Voltage, 2.7 V to 5.25 V. This is the supply voltage for Comparator A and Comparator B. Decouple this supply to CA_CB_GND. AVCC, CC_CDVCC, and CA_CBVCC can be tied together. Comparator Supply Voltage, 2.7 V to 5.25 V. This is the supply voltage for Comparator C and Comparator D. Decouple this supply to CC_CD_GND. AVCC, CC_CDVCC, and CA_CBVCC can be tied together. Analog Inputs of ADC A. True differential input pair. Analog Inputs of ADC B. True differential input pair. Reference Input/Output. Decoupling capacitors connect to these pins to decouple the internal reference buffer for each respective ADC. Typically, 1 μF capacitors are required to decouple the reference. Provided the output is buffered, the on-chip reference can be taken from these pins and applied externally to the rest of a system. Serial Clock. Logic input. A serial clock input provides the SCLK for accessing the data from the AD7262/AD7262-5. This clock is also used as the clock source for the conversion process. A minimum of 31 clocks is required to perform the conversion and access the 12-bit result. Logic Input. Initiates an internal offset calibration. Logic Input. Places the AD7262/AD7262-5 in selected shutdown mode in conjunction with the PD1 and PD0 pins (see Table 7). Logic Input. Places the AD7262/AD7262-5 in selected shutdown mode in conjunction with the PD2 and PD0 pins (see Table 7). Rev. C | Page 8 of 32 07606-004 AD7262 AGND 6 AVCC 7 CAL 35 15 16 17 18 19 20 21 22 23 24 AGND 5 36 CC+ 13 CC– 14 PIN 1 INDICATOR AVCC 2 V A– 3 VA+ 4 CD+ CD– CC_CD_GND VREFB AGND AV CC PD2 PD1 PD0/D IN REFSEL 48 47 46 45 44 43 42 41 40 39 38 37 CA_CBVCC 1 45 44 43 42 41 40 39 38 37 48 CA+ 47 CA– 46 CB+ G3 G2 G1 G0 AVCC AGND CB – CA_CB_GND VREFA CB + CA + CA – PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS Data Sheet AD7262 Pin No. 23 Mnemonic PD0/DIN 35 48, 47, 46, 45 5, 6, 8, 19, 42 CS CA+, CA−, CB+, CB− CC+, CC−, CD+, CD− AGND 28 DGND 30, 29, 26, 25 32, 31 COUTA, COUTB, COUTC, COUTD DOUTA, DOUTB 40, 39, 38, 37 G0, G1, G2, G3 27 VDRIVE 44, 17 CA_CB_GND, CC_CD_GND 24 REFSEL 13, 14, 15, 16 EPAD Description Logic Input/Data Input. Places the AD7262/AD7262-5 in selected shutdown mode in conjunction with the PD2 and PD1 pins (see Table 7). If all gain selection pins, G0 to G3, are tied low, this pin acts as the data input pin, and all programming is via the control register (see Table 8). Data to be written to the AD7262/AD7262-5 control register is provided on this input and is clocked into the register on the falling edge of SCLK. Chip Select. Active low logic input. This input initiates conversions on the AD7262/AD7262-5. Comparator Inputs. These pins are the inverting and noninverting analog inputs for Comparator A and Comparator B. These two comparators have very low power consumption. Comparator Inputs. These pins are the inverting and noninverting analog inputs for Comparator C and Comparator D. This pair of comparators offers very fast propagation delays. Analog Ground. Ground reference point for all analog circuitry on the AD7262/AD7262-5. Refer all analog input signals and any external reference signal to this AGND voltage. All AGND pins should connect to the AGND plane of a system. The AGND, DGND, CA_CB_GND, and CC_CD_GND voltages ideally should be at the same potential and must not be more than 0.3 V apart, even on a transient basis. CA_CB_GND and CC_CD_GND can be tied to AGND. Digital Ground. This is the ground reference point for all digital circuitry on the AD7262/AD7262-5. Connect the DGND pin to the DGND plane of a system. The DGND and AGND voltages should ideally be at the same potential and must not be more than 0.3 V apart, even on a transient basis. Comparator Outputs. These pins provide a CMOS (push-pull) output from each respective comparator. These are digital output pins with logic levels determined by the VDRIVE supply. Serial Data Outputs. The data output from the AD7262/AD7262-5 is supplied to each pin as a serial data stream in twos complement format. The bits are clocked out on the falling edge of the SCLK input. A total of 31 SCLKs is required to perform the conversion and access the 12-bit data. During the conversion process, the data output pins are in three-state and, when the conversion is completed, the 19th SCLK edge clocks out the MSB. The data simultaneously appears on both pins from the simultaneous conversions of both ADCs. The data is provided MSB first. If CS is held low for an additional 14 SCLK cycles on either DOUTA or DOUTB following the initial 31 SCLKs, the data from the other ADC follows on the DOUT pin. This allows data from a simultaneous conversion on both ADCs to be gathered in serial format on either DOUTA or DOUTB using only one serial port. Logic Inputs. These pins program the gain setting of the front-end amplifiers. If all four pins are tied low, the PD0 pin acts as a data input pin, DIN, and all programming is made via the control register (see Table 6). Logic Power Supply Input, 2.7 V to 5.25 V. The voltage supplied at this pin determines at what voltage the interface operates, including the comparator outputs. Decouple this pin to DGND. Comparator Ground. This is the ground reference point for all comparator circuitry on the AD7262/ AD7262-5. Both the CA_CB_GND pin and the CC_CD_GND pin must connect to the GND plane of a system and can be tied to AGND. The DGND, AGND, CA_CB_GND, and CC_CD_GND voltages should ideally be at the same potential and must not be more than 0.3 V apart, even on a transient basis. Internal/External Reference Selection. Logic input. If this pin is tied to a logic high voltage, the onchip 2.5 V reference is used as the reference source for both ADC A and ADC B. If the REFSEL pin is tied to GND, an external reference can be supplied to the AD7262/AD7262-5 through the VREFA and/or VREFB pin. Exposed Metal Paddle. The exposed metal paddle on the bottom of the LFCSP package must be soldered to PCB ground for proper heat dissipation and also for noise and mechanical strength benefits. Rev. C | Page 9 of 32 AD7262 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS 0.6 0.2 0 –0.2 0.2 0 –0.2 1500 2000 2500 3000 3500 4000 CODE –0.6 0 500 0.8 0.6 0.6 0.4 0.4 INL ERROR (LSB) 0.8 0.2 0 –0.2 AVCC = 5V VDRIVE = 5V fS = 1MSPS TA = 25°C INTERNAL REFERENCE PGA GAIN = 2 –1.0 0 500 1000 1500 2500 3000 3500 4000 CODE –0.4 –1.0 –40 0 500 0 (dB) –120 FREQUENCY (Hz) 2500 3000 4000 –80 –120 100k 150k 200k 250k 300k 350k 400k 450k 2000 TA = 25°C fIN = 100kHz INTERNAL REFERENCE SNR = 68.38dB, THD = –82dB PGA GAIN = 32 –60 –100 50k 1500 AVCC = 5V VDRIVE = 5V –40 –100 0 1000 fS = 1MSPS –20 –80 –140 3500 AVCC = 5V VDRIVE = 5V fS = 1MSPS TA = 25°C INTERNAL REFERENCE PGA GAIN = 32 Figure 9. Typical INL at Gain of 32 07606-007 (dB) –60 4000 CODE AVCC = 5V VDRIVE = 2.7V fS = 1MSPS TA = 25°C fIN = 100kHz INTERNAL REFERENCE SNR = 73dB, THD = –82.5dB PGA GAIN = 2 –20 3500 0 Figure 6. Typical INL at Gain of 2 0 3000 –0.2 –0.8 2000 2500 0.2 –0.6 07606-006 INL ERROR (LSB) 1.0 –0.8 2000 Figure 8. Typical DNL at Gain of 32 1.0 –0.6 1500 CODE Figure 5. Typical DNL at Gain of 2 –0.4 1000 07606-008 1000 Figure 7. 3 dB Typical FFT at Gain of 2 –140 0 50k 100k 150k 200k 250k 300k 350k 400k 450k 500k FREQUENCY (Hz) Figure 10. Typical FFT at Gain of 32 Rev. C | Page 10 of 32 07606-010 500 07606-005 0 07606-009 –0.4 –0.4 –0.6 AVCC = 5V VDRIVE = 5V fS = 1MSPS TA = 25°C INTERNAL REFERENCE PGA GAIN = 32 0.4 DNL ERROR (LSB) 0.4 DNL ERROR (LSB) 0.6 AVCC = 5V VDRIVE = 5V fS = 1MSPS TA = 25°C INTERNAL REFERENCE PGA GAIN = 2 Data Sheet AD7262 9000 2.4968 8839 8000 2.4967 2.4966 6000 5000 VREF (V) 4000 2.4965 2.4964 3000 2.4963 828 0 2043 2044 0 2045 CODE 2.4961 3dB BANDWIDTH (kHz) 3000 2000 1732 1297 140 160 180 200 1500 1400 1300 1200 1100 1000 900 1000 800 2045 2046 2047 0 700 2049 600 07606-012 4 2048 0 2044 CODE AVCC = 5V VDRIVE = 5V fS = 1MSPS INTERNAL REFERENCE 1 2 3 4 6 8 12 16 24 32 48 64 96 128 64 96 128 GAIN Figure 12. Histogram of Codes for 10k Samples at Gain of 32 Figure 15. 3 dB Bandwidth vs. Gain 80 AVCC = 5V VDRIVE = 5V fS = 1MSPS INTERNAL REFERENCE 75 70 65 –65 GAIN = 32 SNR (dB) THD (dB) 120 1600 4000 –70 –75 GAIN = 2 60 55 50 45 –70 40 –85 35 110 210 310 410 510 610 710 810 ANALOG INPUT FREQUENCY (kHz) 910 07606-013 –90 10 100 1700 5000 –60 80 1800 6000 –55 60 1900 6967 7000 –50 40 Figure 14. VREF vs. Reference Output Current Load 8000 NUMBER OF HITS 20 CURRENT LOAD (µA) Figure 11. Histogram of Codes for 10k Samples at Gain of 2 0 0 07606-015 0 AVCC = 5V VDRIVE = 3V fS = 1MSPS INTERNAL REFERENCE 2.4962 333 07606-011 1000 Figure 13. THD vs. Analog Input Frequency up to 1 MHz at Gain of 2 and 32 Rev. C | Page 11 of 32 30 AVCC = 5V VDRIVE = 5V fS = 1MSPS INTERNAL REFERENCE FIN = 100kHz 1 2 3 4 6 8 12 16 24 32 48 PGA GAIN Figure 16. SNR vs. PGA Gain for an Analog Input Tone of 100 kHz 07606-014 2000 07606-016 NUMBER OF HITS 7000 AD7262 Data Sheet 10 –88 9 –86 8 PROPAGATION DELAY (µs) –90 –82 –80 –78 AVCC = 5V VDRIVE = 5V fS = 1MSPS INTERNAL REFERENCE fRIPPLE = 50kHz –72 –70 1 2 3 4 6 8 12 16 24 32 48 96 128 64 GAIN 4 3 2 0 –79 1.8 –78 1.6 PROPAGATION DELAY (µs) 2.0 –76 –75 –74 AVCC = 5V VDRIVE = 5V fS = 1MSPS VRIPPLE = 700mV p-p GAIN = 2 INTERNAL REFERENCE –71 –70 0 20 40 60 80 100 120 140 160 180 200 RIPPLE FREQUENCY (kHz) Figure 18. Common-Mode Rejection vs. Common-Mode Ripple Frequency –20 –30 1.0 0.8 0.6 0.4 0 10 90 100 CC_CDVCC CC_CDVCC CC_CDVCC CC_CDVCC CC_CDVCC CC_CDVCC CC_CDVCC CC_CDVCC = 2.7V = 3.6V = 4.5V = 5V = 2.7V = 3.6V = 5V = 4.5V 20 30 40 50 60 70 80 90 100 VDRIVE = 5V GAIN = 2 TA = 25°C INTERNAL REFERENCE 100mV p-p SINE WAVE ON AVCC AVCC DECOUPLED WITH 10µF AND 100nF CAPACITORS –80 –85 PSRR (dB) GAIN 3 –90 –95 –100 –105 GAIN 16 –110 –115 –90 GAIN 12 1.3 1.5 1.7 1.9 2.1 2.3 GAIN 6 GAIN ≥ 32 GAIN 24 2.5 2.7 VCM RANGE (V) 2.9 3.1 3.3 3.5 3.7 –120 07606-019 –100 80 Figure 21. Propagation Delay for Comparator C and Comparator D vs. Overdrive Voltage for Various Supply Voltages GAIN 2 –60 –80 L TO H, L TO H, L TO H, L TO H, H TO L, H TO L, H TO L, H TO L, 1.2 –75 GAIN 4 70 AVCC = 5V VDRIVE = 3.3V TA = 25°C –70 –50 GAIN 8 60 50 OVERDRIVE VOLTAGE (mV) –40 –70 40 1.4 0 GAIN 1 AVCC = 5V VDRIVE = 5V fS = 1MSPS INTERNAL REFERENCE fIN = 100kHz 30 Figure 19. THD vs. Common-Mode Range for Various PGA Gain Settings 0 200 400 600 800 SUPPLY RIPPLE FREQUENCY (kHz) 1000 07606-022 –10 20 0.2 07606-018 –72 10 OVERDRIVE VOLTAGE (mV) –80 –73 0 Figure 20. Propagation Delay for Comparator A and Comparator B vs. Overdrive Voltage for Various Supply Voltages –77 CMR (dB) 5 = 3.6V = 4.5V = 2.7V = 5V = 2.7V = 3.6V = 4.5V = 5V 1 Figure 17. Common-Mode Rejection vs. Gain THD (dB) 6 CA_CBVCC CA_CBVCC CA_CBVCC CA_CBVCC CA_CBVCC CA_CBVCC CA_CBVCC CA_CBVCC 07606-020 –74 H TO L, H TO L, H TO L, H TO L, L TO H, L TO H, L TO H, L TO H, 7 07606-021 –76 07606-017 CMR (dB) –84 AVCC = 5V VDRIVE = 3.3V TA = 25°C Figure 22. Power Supply Rejection Ratio vs. Supply Ripple Frequency? Rev. C | Page 12 of 32 Data Sheet 300 COUTA/COUTB SINK CURRENT COUTC/COUTD SINK CURRENT 200 VOUT (V) OR VDD – VOUT (mV) AD7262 DOUT SINK CURRENT 100 0 –100 DOUT SOURCE CURRENT –200 COUTC/COUTD SOURCE CURRENT 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 0.1 0.3 0.5 0.7 0.9 1.1 1.3 1.5 1.7 1.9 2.1 2.3 2.5 CURRENT (mA) 07606-023 –300 COUTA/COUTB SOURCE CURRENT Figure 23. DOUT and COUT Source and Sink Current Rev. C | Page 13 of 32 AD7262 Data Sheet TERMINOLOGY Differential Nonlinearity (DNL) Differential nonlinearity is the difference between the measured and the ideal 1 LSB change between any two adjacent codes in the ADC. Integral Nonlinearity (INL) Integral nonlinearity is the maximum deviation from a straight line passing through the endpoints of the ADC transfer function. The endpoints of the transfer function are zero scale, a single (1) LSB point below the first code transition, and full scale, a single (1) LSB point above the last code transition. Zero Code Error This is the deviation of the midscale transition (all 1s to all 0s) from the ideal VIN voltage, that is, VCM – ½ LSB. Positive Full-Scale Error This is the deviation of the last code transition (011 … 110) to (011 … 111) from the ideal, that is,  V  VCM +  REF  − 1 LSB  2 × Gain  after the zero code error has been adjusted out. Negative Full-Scale Error This is the deviation of the first code transition (10 … 000) to (10 … 001) from the ideal, that is, VCM  V  −  REF  + 1 LSB  2 × Gain  after the zero code error has been adjusted out. Zero Code Error Match This is the difference in zero code error across both ADCs. Positive Full-Scale Error Match This is the difference in positive full-scale error across both ADCs. Negative Full-Scale Error Match This is the difference in negative full-scale error across both ADCs. Track-and-Hold Acquisition Time The track-and-hold amplifier returns to track mode at the end of a conversion. Track-and-hold acquisition time is the time required for the output of the track-and-hold amplifier to reach its final value, within ±1/2 LSB, after the end of a conversion. Signal-to-(Noise + Distortion) Ratio This ratio is the measured ratio of signal-to-(noise + distortion) at the output of the analog-to-digital converter. The signal is the rms amplitude of the fundamental. Noise is the sum of all nonfundamental signals up to half the sampling frequency (fS/2), excluding dc. The ratio is dependent on the number of quantization levels in the digitization process; the more levels, the smaller the quantization noise. The theoretical signal-to-(noise + distortion) ratio for an ideal N-bit converter with a sine wave input is given by Signal-to-(Noise + Distortion) = (6.02N + 1.76) dB Thus for a 12-bit converter, this is 86 dB. Total Harmonic Distortion (THD) Total harmonic distortion is the ratio of the rms sum of harmonics to the fundamental. For the AD7262/AD7262-5, it is defined as 2 THD(dB) = 20 log 2 2 2 V2 + V3 + V4 + V5 + V6 2 V1 where V1 is the rms amplitude of the fundamental, and V2, V3, V4, V5, and V6 are the rms amplitudes of the second through the sixth harmonics. Peak Harmonic or Spurious Noise Peak harmonic, or spurious noise, is defined as the ratio of the rms value of the next largest component in the ADC output spectrum (up to fS/2, excluding dc) to the rms value of the fundamental. Normally, the value of this specification is determined by the largest harmonic in the spectrum, but for ADCs where the harmonics are buried in the noise floor, it is a noise peak. ADC-to-ADC Isolation ADC-to-ADC isolation is a measure of the level of crosstalk between the ADC A and ADC B. It is measured by applying a full-scale, 100 kHz sine wave signal to all unselected input channels and determining how much that signal is attenuated in the selected channel with a 40 kHz signal. The figure given is the worst case. PSRR (Power Supply Rejection) Variations in power supply affect the full-scale transition but not the linearity of the converter. Power supply rejection is the maximum change in the full-scale transition point due to a change in power supply voltage from the nominal value (see Figure 22). Propagation Delay Time, Low to High (tPLH) Propagation delay time from low to high is defined as the time taken from the 50% point on a low to high input signal until the digital output signal reaches 50% of its final low value. Propagation Delay Time, High to Low (tPHL) Propagation delay time from high to low is defined as the time taken from the 50% point on a high to low input signal until the digital output signal reaches 50% of its final high value. Comparator Offset Comparator offset is the measure of the density of digital 1s and 0s in the comparator output when the negative analog terminal of the comparator input is held at a static potential and the analog input to the positive terminal of the comparators is varied proportionally about the static negative terminal voltage. Rev. C | Page 14 of 32 Data Sheet AD7262 THEORY OF OPERATION CIRCUIT INFORMATION The AD7262/AD7262-5 are fast, dual, simultaneous sampling, differential, 12-bit, serial ADCs. The AD7262/AD7262-5 contain two on-chip differential programmable gain amplifiers, two track-and-hold amplifiers, and two successive approximation analog-to-digital converters with a serial interface with two separate data output pins. The AD7262/AD7262-5 also include four on-chip comparators. They are housed in a 48-lead LFCSP and in a 48-lead LQFP, offering the user considerable spacesaving advantages over alternative solutions. The AD7262/ AD7262-5 require a low voltage 5 V ± 5% AVCC to power the ADC core and supply the digital power, a 5.25 V to 2.7 V CA_CBVCC, CC_CDVCC supply for the comparators, and a 2.7 V to 5.25 V VDRIVE supply for interface power. The on-board PGA allows the user to select from 14 programmable gain stages: ×1, ×2, ×3, ×4, ×6, ×8, ×12, ×16, ×24, ×32, ×48, ×64, ×96, and ×128. The PGA accepts fully differential analog signals. The gain can be selected either by setting the logic state of the G0 to G3 pins or by programming the control register. The serial clock input accesses data from the part while also providing the clock source for each successive approximation ADC. The AD7262/AD7262-5 have an on-chip 2.5 V reference that can be disabled when an external reference is preferred. If the internal reference is used elsewhere in a system, the output from VREFA and VREFB must first be buffered. If the internal reference is the preferred option, the user must tie the REFSEL pin to a logic high voltage. Alternatively, if the REFSEL pin is tied to GND, an external reference can be supplied to both ADCs through the VREFA and VREFB pins (see the Reference section). The AD7262/AD7262-5 also feature a range of power-down options to allow the user great flexibility with the independent circuit components while allowing for power savings between conversions. The power-down feature is implemented via the control register or the PD0 to PD2 pins, as described in the Control Register section. Each pair of comparators operates from its own independent supply, CA_CBVCC and CC_CDVCC. The comparators are specified for supply voltages from 2.7 V to 5.25 V. If desired, CA_CBVCC and CC_CDVCC can be tied to the AVCC supply. The four comparators on the AD7262/AD7262-5 are functional with CA_CBVCC/ CC_CDVCC greater than or equal to 1.8 V. However, no specifications are guaranteed for comparator supplies less than 2.7 V. The wide range of supply voltages ensures that the comparators can be used in a variety of battery backup modes. The four on-chip comparators on the AD7262/AD7262-5 are ideally suited for monitoring signals from pole sensors in motor control systems. The comparators can be used to monitor signals from Hall effect sensors or the inner tracks from an optical encoder. One of the comparators can be used to count the index marker or z marker, which is used on startup to place the motor in a known position. OPERATION The AD7262/AD7262-5 have two successive approximation ADCs, each based around two capacitive DACs and two programmable gate amplifiers. The ADC itself comprises control logic, a SAR, and two capacitive DACs. The control logic and the charge redistribution DACs are used to add and subtract fixed amounts of charge from the sampling capacitor amplifiers to bring the comparator back into a balanced condition. When the comparator is rebalanced, the conversion is complete. The control logic generates the ADC output code. Each ADC is preceded by its own programmable gain stage. The PGA features high analog input impedance, true differential analog inputs that allow the output from any source or sensor to be connected directly to the PGA inputs without any requirement for additional external buffering. The variable gain settings ensure that the device can be used for amplifying signals from a variety of sources. The AD7262/AD7262-5 offer the flexibility to choose the most appropriate gain setting to use the wide dynamic range of the device. COMPARATORS ANALOG INPUTS The AD7262/AD7262-5 have four on-chip comparators. Comparator A and Comparator B have ultralow power consumption, with static power consumption typically less than 10 μW with a 3.3 V supply. Comparator C and Comparator D feature very fast propagation delays of 130 ns for a 200 mV differential overdrive. These comparators have push-pull output stages that operate from the VDRIVE supply. This feature allows operation with a minimum amount of power consumption. Each ADC in the AD7262/AD7262-5 has two high impedance differential analog inputs. Figure 24 shows the equivalent circuit of the analog input structure of the AD7262/AD7262-5. It consists of a fully differential input amplifier that buffers the analog input signal and provides the gain selected by using the gain pins or the control register. Rev. C | Page 15 of 32 AD7262 Data Sheet The two diodes provide ESD protection. Care must be taken to ensure that the analog input signals never exceed the supply rails by more than 300 mV. Exceeding 300 mV causes these diodes to become forward-biased and to start conducting current into the substrate. These diodes can conduct up to 10 mA without causing irreversible damage to the part. The C1 capacitors in Figure 24 are typically 5 pF and can primarily be attributed to pin capacitance. VDD VIN+ AMP C1 VOUT+ When a full-scale step input is applied to either differential input on the AD7262/AD7262-5 while the other analog input is held at a constant voltage, 3 μs of settling time is typically required prior to capturing a stable digital output code. Transfer Function The AD7262/AD7262-5 output is twos complement, and the ideal transfer characteristic is shown in Figure 25. The designed code transitions occur at successive integer LSB values (that is, 1 LSB, 2 LSB, and so on). The LSB size is dependent on the analog input range selected. The LSB size for the AD7262/AD7262-5 is shown in the following equation:  VREF     VREF      VCM +    −  VCM −    2 × Gain     2 × Gain     2×  4096       VDD VOUT – 07606-024 AMP C1 Figure 24. Analog Input Structure 011...111 011...110  V   V  VCM −  REF  to VCM +  REF   2 × Gain   2 × Gain  Table 5 details the analog input range for the AD7262/AD7262-5 for the various PGA gain settings. Here, VREF = 2.5 V and VCM = 2.5 V (AVCC/2, with AVCC = 5 V). ADC CODE The AD7262/AD7262-5 can accept differential analog inputs from 1 Analog Input Range for VIN+ and VIN− 0.75 V to 3.25 V1 1.875 V to 3.125 V 2.083 V to 2.916 V 2.187 V to 2.813 V 2.292 V to 2.708 V 2.344 V to 2.656 V 2.396 V to 2.604 V 2.422 V to 2.578 V 2.448 V to 2.552 V 2.461 V to 2.539 V 2.474 V to 2.526 V 2.480 V to 2.520 V 2.487 V to 2.513 V 2.490 V to 2.510 V 000...000 111...111 100...010 100...001 Table 5. Analog Input Range for Various PGA Gain Settings PGA Gain Setting 1 2 3 4 6 8 12 16 24 32 48 64 96 128 000...001 100...000 0V (VCM – (FSR/2)) + 1LSB (VCM + (FSR/2)) – 1LSB ANALOG INPUT NOTES 1. FULL-SCALE RANGE (FSR) = VIN+ – VIN–. 07606-025 VIN– Figure 25. Twos Complement Transfer Function VDRIVE The AD7262/AD7262-5 have a VDRIVE feature to control the voltage at which the serial interface operates. VDRIVE allows the ADC and the comparators to interface easily to both 3 V and 5 V processors. For example, when the AD7262/AD7262-5 are operated with AVCC = 5 V, the VDRIVE pin can be powered from a 3 V supply, allowing a large analog input range with low voltage digital processors. For VCM = 2 V. If VCM = AVCC /2, the analog input range for VIN+ and VIN− is 1.6 V to 3.4 V. Rev. C | Page 16 of 32 Data Sheet AD7262 REFERENCE TYPICAL CONNECTION DIAGRAMS The AD7262/AD7262-5 can operate with either the internal 2.5 V on-chip reference or an externally applied reference. The logic state of the REFSEL pin determines whether the internal reference is used. The internal reference is selected for both ADCs when the REFSEL pin is tied to logic high. If the REFSEL pin is tied to AGND, an external reference can be supplied through the VREFA and/or VREFB pins. On power-up, the REFSEL pin must be tied to either a low or high logic state for the part to operate. Suitable reference sources for the AD7262/AD7262-5 include AD780, AD1582, ADR431, REF193, and ADR391. Figure 26 and Figure 27 are typical connection diagrams for the AD7262/AD7262-5. In these configurations, the AGND pin is connected to the analog ground plane of the system, and the DGND pin is connected to the digital ground plane of the system. The analog inputs on the AD7262/AD7262-5 are true differential and have an input impedance in excess of 1 GΩ; thus, no driving op amps are required. The AD7262/AD7262-5 can operate with either an internal or an external reference. In Figure 26, the AD7262/AD7262-5 are configured to operate in control register mode; thus, G0 to G3, PD1, and PD2 can be connected to ground (low logic state). Figure 27 has the gain pins configured for a gain of 2 setup; thus, the device is in pin-driven mode. Both circuit configurations illustrate the use of the internal 2.5 V reference The internal reference circuitry consists of a 2.5 V band gap reference and a reference buffer. When the AD7262/AD7262-5 are operated in internal reference mode, the 2.5 V internal reference is available at the VREFA and VREFB pins, which should be decoupled to AGND using a 1 μF capacitor. It is recommended that the internal reference be buffered before applying it elsewhere in the system. The internal reference is capable of sourcing up to 90 μA of current when the converter is static. If the internal reference operation is required for the ADC conversion, the REFSEL pin must be tied to logic high on power-up. The reference buffer requires 240 µs to power up and charge the 1 μF decoupling capacitor during the power-up time. The CA_CBVCC and the CC_CDVCC pins can be connected to either a 3 V or a 5 V supply voltage. The AVCC pin must be connected to a 5 V supply. All supplies should be decoupled with a 100 nF capacitor at the device pin, and some supply sources may require a 10 μF capacitor where the source is supplied to the circuit board. The VDRIVE pin is connected to the supply voltage of the microprocessor. The voltage applied to the VDRIVE input controls the voltage of the serial interface. VDRIVE can be set to 3 V or 5 V. Rev. C | Page 17 of 32 AD7262 Data Sheet ANALOG SUPPLY +5V 100nF 10µF1 100nF 100nF 100nF 100nF 10µF1 COMPARATOR SUPPLY 3V TO 5V2 100nF 100nF VA– AND VA+ CONNECT DIRECTLY TO SENSOR OUTPUTS 3 1.875V AVCC CA–CBVCC AVCC CC–CDVCC AVCC AVCC AVCC AVCC AGND DGND 7 11 20 41 12 1 33 AGND 8 19 42 28 2 AGND 6 V A– VDRIVE V A+ G0 G1 G2 G3 GAIN 2 3.125V 4 2.500V 1.875V AGND CC–CD–GND 3.125V 2.500V CA–CB–GND 17 44 5 AGND 100nF THIS REFERENCE SIGNAL MUST BE BUFFERED BEFORE IT CAN BE USED ELSEWHERE IN THE CIRCUIT VREF A SCLK AD7262 CS DOUTA VREF B DOUTB 1µF REFSEL 3.125V 9 2.500V V B+ PD0/DIN GAIN 2 PD1 13 14 15 16 45 46 47 48 10µF1 3V OR 5V SUPPLY 34 35 MICROPROCESSOR/ MICROCONTROLLER 32 31 24 VDRIVE 36 23 22 21 COUTA COUTB COUTC COUTD C A+ CB+ C A– C B– GAIN 2 PD2 CD– 2.500V VB– CC+ 10 CD+ 3.125V 1.875V CAL C C– 1.875V 100nF SERIAL INTERFACE 1µF 18 VDRIVE 40 39 38 37 GAIN 2 43 VB– AND VB+ CONNECT DIRECTLY TO SENSOR OUTPUTS 27 25 26 29 30 1THESE CAPACITORS ARE PLACED AT THE SUPPLY SOURCE AND MAY NOT BE 2THIS SUPPLY CAN BE CONNECTED TO THE ANALOG 5V SUPPLY IF REQUIRED. REQUIRED IN ALL SYSTEMS. Figure 26. Typical Connection Diagram for the AD7262/AD7262-5 in Control Register Mode (All Gain Pins Tied to Ground) Configured for a PGA Gain of 2 Rev. C | Page 18 of 32 07606-026 FAST PROPAGATION DELAY LOW POWER COMPARATOR INPUTS COMPARATOR INPUTS Data Sheet AD7262 ANALOG SUPPLY +5V 100nF 10µF1 100nF 100nF 100nF 100nF 10µF1 COMPARATOR SUPPLY 3V TO 5V2 100nF 100nF VA– AND VA+ CONNECT DIRECTLY TO SENSOR OUTPUTS 3 2.500V 1.875V AVCC CA–CBVCC AVCC CC–CDVCC AVCC AVCC AVCC AVCC AGND DGND 7 11 20 41 12 1 33 AGND 8 19 42 28 2 AGND 6 VA– VDRIVE V A+ G0 G1 G2 G3 GAIN 2 3.125V 4 2.500V 1.875V AGND CC–CD–GND 3.125V CA–CB–GND 17 44 5 AGND 100nF THIS REFERENCE SIGNAL MUST BE BUFFERED BEFORE IT CAN BE USED ELSEWHERE IN THE CIRCUIT VREF A SCLK 1µF 18 AD7262 CS DOUTA VREF B DOUTB REFSEL 9 PD0/DIN PD1 13 14 15 16 45 46 47 48 COUTB COUTD CA+ C A– C B+ CB– CD– PD2 C D+ GAIN 2 VB– CC+ 10 2.500V C C– 3.125V 1.875V V B+ GAIN 2 COUTA 2.500V CAL COUTC 3.125V VDRIVE 100nF 10µF1 3V OR 5V SUPPLY VDRIVE GAIN 2 SETUP SERIAL INTERFACE 1µF 1.875V 40 39 38 37 GAIN 2 43 VB– AND VB+ CONNECT DIRECTLY TO SENSOR OUTPUTS 27 34 35 MICROPROCESSOR/ MICROCONTROLLER 32 31 24 VDRIVE 36 23 VDRIVE 22 21 VDRIVE BOTH COMPARATORS AND ADCs POWERED ON 25 26 29 30 1THESE CAPACITORS ARE PLACED AT THE SUPPLY SOURCE AND MAY NOT BE 2THIS SUPPLY CAN BE CONNECTED TO THE ANALOG 5V SUPPLY IF REQUIRED. REQUIRED IN ALL SYSTEMS. Figure 27. Typical Connection Diagram for the AD7262/AD7262-5 in Pin-Driven Mode with Gain of 2 and Both ADCs and Comparators Fully Powered On Rev. C | Page 19 of 32 07606-027 FAST PROPAGATION DELAY LOW POWER COMPARATOR INPUTS COMPARATOR INPUTS AD7262 Data Sheet Comparator Application Details APPLICATION DETAILS The comparators on the AD7262/AD7262-5 have been designed with no internal hysteresis, allowing users the flexibility to add external hysteretic if required for systems operating in noisy environments. If the comparators on the AD7262/AD7262-5 are used with external hysteresis, some external resistors and capacitors are required, as shown in Figure 28. The value of RF and RS, the external resistors, can be determined using the following equation, depending on the amount of hysteresis required in the application: The AD7262/AD7262-5 have been specifically designed to meet the requirements of any motor control shaft position feedback loop. The devices can interface directly to multiple sensor types, including optical encoders, magneto resistive sensors, and Hall effect sensors. Flexible analog inputs that incorporate programmable gain ensure that identical board design can be used for a variety of sensors, which results in reduced design cycles and costs. VHYS = RS × C x _ C x VCC RS + RF where Cx_CxVCC = CA_CBVCC or CC_CDVCC. The amount of hysteresis chosen must be sufficient to eliminate the effects of analog noise at the comparator inputs, which may affect the stability of the comparator outputs. The level of hysteresis required in any system depends on the noise in the system; thus, the values of RF and RS need to be carefully selected to eliminate any noise effects. To increase the level of hysteresis in the system, increase the value of RS or RF. For example, RF = 10 MΩ, RS = 1 kΩ give 330 μV of hysteresis with a Cx_CxVCC of 3.3 V; if hysteresis is increased to 1 mV, RS = 3.1 kΩ. In certain applications, a load capacitor (100 pF) may be required on the comparator outputs to suppress high frequency transient glitches. The two simultaneous sampling ADCs are used to sample the sine and cosine outputs from the sensor. No external buffering is required between the sensor/transducer and the analog inputs of the AD7262/AD7262-5. The on-chip comparators can be used to monitor the pole sensors, which can be Hall effect sensors or the inner tracks from an optical encoder. Figure 29 shows how the AD7262/AD7262-5 can be used in a typical application. An optical encoder is shown in Figure 29, but other sensor types could as easily be used. Figure 29 indicates a typical application configuration only, and there are several other configurations that render equally effective results. SENSOR RS C x– RS C x+ COUTx 07606-028 RF Figure 28. Recommended Comparator Connection Diagram Rev. C | Page 20 of 32 Data Sheet AD7262 COMP COMP VREF A AVCC REF 12-BIT SUCCESSIVE APPROXIMATION ADC VA+ A VA– AD7262 BUF PGA T/H OUTPUT DRIVERS SCLK CAL CS REFSEL G0 G1 G2 G3 VDRIVE CONTROL LOGIC B VB+ VB– PGA 12-BIT SUCCESSIVE APPROXIMATION ADC T/H DOUTA OUTPUT DRIVERS BUF DOUTB PD0/DIN PD1 PD2 VREF B Z CA_CBVCC C A+ CA– U CB+ COMP CB– CA_CB_GND V W COMP CC_CDVCC CC+ CC– CD+ CD– CC_CD_GND OUTPUT DRIVERS COMP COUTA OUTPUT DRIVERS OUTPUT DRIVERS COMP AGND COUTC OUTPUT DRIVERS DGND Figure 29. Typical System Connection Diagram with Optical Encoder Rev. C | Page 21 of 32 COUTB COUTD 07606-029 H.E. AD7262 Data Sheet MODES OF OPERATION The AD7262/AD7262-5 allow the user to choose between two modes of operation, pin-driven mode and control register mode. PIN-DRIVEN MODE In pin-driven mode, the user can select the gain of the PGA, the power-down mode, internal or external reference, and initiate a calibration of the offset for both ADC A and ADC B. These functions are implemented by setting the logic levels on the gain pins (G3 to G0), the power-down pins (PD2 to PD0), the REFSEL pin, and the CAL pin, respectively. The logic state of Pin G3 to Pin G0 determines which mode of operation is selected. Pin-driven mode is selected if at least one of the gain pins is set to a logic high state. Alternatively, if all four gain pins are connected to a logic low, the control register mode of operation is selected. GAIN SELECTION The on-board PGA allows the user to select from 14 programmable gain stages: ×1, ×2, ×3, ×4, ×6, ×8, ×12, ×16, ×24, ×32, ×48, ×64, ×96, and ×128. The PGA accepts fully differential analog signals and provides three key functions, which include selecting gains for small amplitude input signals, driving the ADCs switched capacitive load, and buffering the source from the switching effects of the SAR ADCs. The AD7262/AD7262-5 offer the user great flexibility in user interface, providing gain selection via the control register or by driving the gain pins to the desired logic state. The AD7262/AD7262-5 have four gain pins, G3, G2, G1 and G0, as shown in Figure 3. Each gain setting is selected by setting up the appropriate logic state on each of the four gain pins, as outlined in Table 6. If all four gain pins are connected to a logic low level, the part is put in control register mode and the gain settings are selected via the control register. Table 6. Gain Selection G3 0 G2 0 G1 0 G0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 1 1 1 1 0 0 0 0 1 1 1 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 Gain Software control via control register 1 2 3 4 6 8 12 16 24 32 48 64 96 128 POWER-DOWN MODES The AD7262/AD7262-5 offer the user a number of power-down options to enable individual device components to be powered down independently. These options can be chosen to optimize the power dissipation for different application requirements. The power-down modes can be selected by either programming the device via the control register or by driving the PD pins to the appropriate logic levels. By setting the PD pins to a logic low level when in pin-driven mode, all four comparators and both ADCs can be powered down. The PD2 and PD0 pins must be set to logic high and the PD1 pin set to logic low to power up all circuitry on the AD7262/AD7262-5. The PD pin configurations for the various power-down options are outlined in Table 7. Table 7. Power-Down Modes PD2 0 0 0 0 1 1 11 1 PD1 0 0 1 1 0 0 11 PD0 0 1 0 1 0 1 11 Comparator A, Comparator B Off Off Off On On On Off Comparator C, Comparator D Off Off On Off On On Off ADC A, ADC B Off On Off Off Off On Off PD2 = PD1 = PD0 = 1 resets the AD7262/AD7262-5 when in pin-driven mode only. The AVCC and VDRIVE supplies must continue to be supplied to the AD7262/AD7262-5 when the comparators are powered up but the ADCs are powered-down. External diodes can be used from the CA_CBVCC and/or CC_CDVCC to both the AVCC and the VDRIVE supplies to ensure they retain a supply at all instances. The AD7262/AD7262-5 can be reset in pin-driven mode only by setting the PDx pins to a logic high state. When the device is reset, all the registers are cleared and the four comparators and the two ADCs are left powered down. In normal mode of operation with the ADCs and comparators powered on, the CA_CBVCC/CC_CDVCC supply and the AVCC supply can be at different voltage levels, as indicated in Table 1. When the comparators on the AD7262/AD7262-5 are in powerdown mode, and the CA_CBVCC/CC_CDVCC supplies are at a potential 0.3 V greater than or less than the AVCC supply, the supplies consume more current than would be the case if both sets of supplies were at the same potential. This configuration does not damage the AD7262/AD7262-5 but results in additional current flowing in any or all of the AD7262/AD7262-5 supply pins. This is due to ESD protection diodes within the device. In applications where power consumption in power-down mode is critical, it is recommended that the CA_CBVCC/CC_CDVCC supply and the AVCC supply be held at the same potential. Rev. C | Page 22 of 32 Data Sheet AD7262 Power-Up Conditions These functions can also be implemented by setting the logic levels on the gain pins, the power-down pins, and the CAL pin, respectively. The control register can also be used to read the offset and gain registers. On power-up, the status of the gain pins determine which mode of operation is selected, as outlined in the Gain Selection section. All registers are set to 0 by default. Data is loaded from the PD0/DIN pin of the AD7262/AD7262-5 on the falling edge of SCLK when CS is in a logic low state. The control register is selected by first writing the appropriate four WR bits, as outlined in Table 10. The 12 data bits must then be clocked into the control register of the device. Thus, on the 16th falling SCLK edge, the LSB is clocked into the device. One more SCLK cycle is then required to write to the internal device registers. In total, 17 SCLK cycles are required to successfully write to the AD7262/AD7262-5. The data is transferred on the PD0/DIN line while the conversion result is being processed. The data transferred on the DIN line corresponds to the AD7262/ AD7262-5 configuration for the next conversion. If the AD7262/AD7262-5 are powered up in pin-driven mode, the gain pins and the PDx pins should be configured to the appropriate logic states and a calibration initiated if required. Alternatively, if the AD7262/AD7262-5 are powered up in control register mode, the comparators and ADCs are powered down and the default gain is 1. Thus, powering up in control register mode requires a write to the device to power up the comparators and the ADCs. It takes 15 μs to power up the AD7262/AD7262-5 when using an external reference. When the internal reference is used, 240 μs are required to power up the AD7262/AD7262-5 with a 1 μF decoupling capacitor. Only the information provided on the 12 falling clock edges after the CS falling edge and the initial four write address bits is loaded to the control register. The PD0/DIN pin should have a logic low state for the four bits RD3 to RD0 when using the control register to select the power-down modes or gain setting or when initializing a calibration. The RD bits should also be set to a logic low level to access the ADC results from both DOUTA and DOUTB. CONTROL REGISTER The control register on the AD7262/AD7262-5 is a 12-bit read and write register, which is used to control the device when not in pin-driven mode. The PD0/DIN pin serves as the serial DIN pin for the AD7262/AD7262-5 when the gain pins are set to 0 (that is, the part is not in pin-driven mode). The control register can be used to select the gain of the PGAs, the power-down modes, and the calibration of the offset for both ADC A and ADC B. When operating in the control register mode, PD1 and PD2 should be connected to a low logic state. The power-up status of all bits is 0 and the MSB denotes the first bit in the data stream. The bit functions are outlined in Table 8 and Table 9. Table 8. Control Register Bits MSB Bit 11 RD3 Bit 10 RD2 Bit 9 RD1 Bit 8 RD0 Bit 7 CAL Bit 6 PD2 Bit 5 PD1 Bit 4 PD0 Bit 3 G3 Bit 2 G2 LSB Bit 0 G0 Bit 1 G1 Table 9. Control Register Bit Function Description Bits 11 to 8 7 Mnemonic RD3 to RD0 CAL 6 to 4 3 to 0 PD2 toPD0 G3 to G0 Description Register address bits. These bits select which register the subsequent read is from. See Table 11. Setting this bit high initiates an internal offset calibration. Once the calibration is completed, this pin can be reset low, and the internal offset, which is stored in the on-chip offset registers, is automatically removed from the ADC results. Power-down bits. These bits select which power-down mode is programmed. See Table 7. Gain selection bits. These bits select which gain setting is used on the front-end PGA. See Table 6. Table 10. Write Address Bits WR2 0 WR1 0 WR0 1 Read Register Addressed Control register CS t8 t2 SCLK 1 3 4 5 6 7 8 9 10 11 12 14 13 15 16 17 18 t13 WR3 WR2 WR1 WR0 19 20 30 31 tQUIET THREE-STATE DOUTA PD0/DIN 2 RD3 RD2 DB11 DB10 t14 RD1 RD0 CAL PD2 PD1 PD0 G3 G2 G1 G0 Figure 30. Timing Diagram for a Write Operation to the Control Register Rev. C | Page 23 of 32 THREE-STATE DB0 THREESTATE 07606-030 WR3 0 AD7262 Data Sheet Table 11. Read and Write Register Addresses ON-CHIP REGISTERS RD3 0 0 0 0 0 0 The AD7262/AD7262-5 contain a control register, two offset registers for storing the offsets for each ADC, and two external gain registers for storing the gain error. The control register and the offset and gain registers are read and write registers. On power-up, all registers in the AD7262/AD7262-5 are set to 0. Addressing the On-Chip Registers Writing to a Register RD2 0 0 0 0 1 1 RD1 0 0 1 1 0 0 RD0 0 1 0 1 0 1 Comment ADC result (default) Control register Offset ADC A internal Offset ADC B internal Gain ADC A external Gain ADC B external Reading from a Register Data is loaded from the PD0/DIN pin of the AD7262/AD7262-5 on the falling edge of SCLK when CS is in a logic low state. Four address bits and 12 data bits must be clocked into the device. Thus, on the 16th falling SCLK edge, the LSB is clocked into the AD7262/AD7262-5. One more SCLK cycle is then required to write to the internal device registers. In total, 17 SCLK cycles are required to successfully write to the AD7262/AD7262-5. The control and offset registers are 12-bits registers; the gain registers are 7-bit registers. The internal offset of the device, which has been measured by the AD7262/AD7262-5 and stored in the on-chip registers during the calibration, can be read back by the user. The content of the external gain registers can also be read. To read the content of any register, the user must first write to the control register by writing 0001 to the WR3 to WR0 bits via the PD0/DIN pin, as outlined in Table 10. The next four bits in the control register are the RD bits, which are used to select the desired register from which to read. The appropriate 4-bit address for each of the offset and gain registers is outlined in Table 11. The remaining eight SCLK cycles bits are used to set the remaining bits in the control register to the desired state for the next ADC conversion. When writing to a register, the user must first write the address bits corresponding to the selected register. Table 11 shows the decoding of the address bits. The four RD bits are written MSB first, that is, RD3 followed by RD2, RD1, and RD0. The AD7262/ AD7262-5 decodes these bits to determine which register is being addressed. The subsequent 12 bits of data are written to the addressed register. The 19th SCLK falling edge clocks out the first data bit of the digital code corresponding to the value stored in the selected internal device register on the DOUTA pin. DOUTB outputs the conversion result from ADC B. Once the selected register has been read, the control register must be reset to output the ADC results for future conversions. This is achieved by writing 0001 to the WR3 to WR0 bits, followed by 0000 to the RD bits. The remaining eight bits in the control register should then be set to the required configuration for the next ADC conversion. When writing to the external gain registers, the seven bits of data immediately after the four address bits are written to the register. However, 17 SCLK cycles are still required, and the PD0/DIN pin of the AD7262/AD7262-5 should be tied low for the five additional clock cycles. CS SCLK t8 t2 2 5 6 7 9 8 10 11 12 14 13 15 16 17 18 t13 RD3 RD2 RD1 RD0 19 20 30 31 tQUIET THREE-STATE DOUTA PD0/DIN 4 3 MSB DB11A t14 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB10A DB0A THREE-STATE DB0 THREESTATE 07606-031 1 Figure 31. Timing Diagram for Writing to a Register CS 2 DOUTA PD0/DIN 3 4 5 0 0 0 1 6 7 8 9 11 10 12 13 14 15 16 17 18 19 20 30 31 tQUIET THREE-STATE t13 RD3 RD2 DB11A t14 RD1 RD0 0 0 0 0 0 0 0 0 Figure 32. Timing Diagram for a Read Operation with PD0/DIN as an Input Rev. C | Page 24 of 32 DB10A THREE-STATE DB0A THREESTATE 07606-032 1 SCLK t8 t2 Data Sheet AD7262 SERIAL INTERFACE reading on the 21st SCLK rising edge. The remainder of the 12-bit result follows, with the final bit in the data transfer being valid on the 31st rising edge. The LSB is provided on the 30th falling clock edge. Figure 33 and Figure 34 show the detailed timing diagrams for the serial interfacing of the AD7262/AD7262-5. The serial clock provides the conversion clock and controls the transfer of information from the AD7262/AD7262-5 after the conversion. The AD7262/AD7262-5 has two output pins corresponding to each ADC. Data can be read from the AD7262/AD7262-5 using both DOUTA and DOUTB. Alternatively, a single output pin of the user’s choice can be used. The SCLK input signal provides the clock source for the serial interface. An alternative to reading on the rising SCLK edge is to use a slower SCLK frequency. If a slower SCLK frequency is used, for example 32 MHz with the AD7262, this enables reading on the subsequent falling SCLK edge after the data has been clocked out, as illustrated in Figure 35. A throughput rate of 1 MSPS can still be achieved for the AD7262 when a 32 MHz SCLK frequency is used. The remaining data is then clocked out by subsequent SCLK falling edges. When using a 32 MHz or less SCLK frequency with the AD7262 or when using the AD7262-5, the 20th falling clock edge on the serial clock has the MSB provided for reading and also clocks out the second data bit. The remainder of the 12-bit result follows, with the final bit in the data transfer being valid on the 31st falling edge. The LSB is provided on the 30th falling clock edge. The falling edge of CS puts the track-and-hold into hold mode, at which point the analog input is sampled. The conversion is also initiated at this point and requires a minimum of 19 SCLKs to complete. The DOUTx lines remain in three-state while the conversion is taking place. On the 19th SCLK falling edge, the AD7262/AD7262-5 return to track mode and the DOUTA and DOUTB lines are enabled. The data stream consists of 12 bits of data, MSB first. The MSB of the conversion result is clocked out on the 19th SCLK falling edge to be read by the microcontroller or DSP on either the subsequent SCLK falling edge (20th falling edge) or the 20th SCLK rising edge. The choice of whether to read on the rising or falling SCLK edge depends on the SCLK frequency being used. When the maximum SCLK frequency of 40 MHz is used with a VDRIVE voltage of 5 V, the maximum specified access time (t4) is 23 ns, resulting in 2 ns of setup time, which may not be sufficient for most DSPs or microcontrollers. Under these conditions, it is recommended to use the rising SCLK edge to read the data. In this case, the MSB of the conversion result is clocked out on the 19th SCLK falling edge to be read on the 20th SCLK rising edge, as shown in Figure 33. The remaining data is then clocked out by subsequent SCLK falling edges. When using a 40 MHz SCLK frequency, the 20th falling clock edge on the serial clock clocks out the second data bit, which is provided for On the rising edge of CS, DOUTA and DOUTB go back into threestate. If CS is not brought high after 31 SCLKs but is instead held low for an additional 14 SCLK cycles, the data from ADC B is output on DOUTA after the ADC A result. Likewise, the data from ADC A is output on DOUTB after the ADC B result. This is illustrated in Figure 34, which shows the DOUTA example. In this case, the DOUT line in use goes back into three-state on the 47th SCLK falling edge or the rising edge of CS, whichever occurs first. If the falling edge of SCLK coincides with the falling edge of CS, the falling edge of SCLK is not acknowledged by the AD7262 and the next falling edge of SCLK is the first one registered after the falling edge of CS. FIRST DATA BIT CLOCKED OUT ON THE 19TH FALLING EDGE FIRST DATA BIT READ ON 20TH RISING EDGE CS t8 t2 1 2 3 4 5 18 19 20 21 22 t4 DOUTA DOUTB THREE-STATE THREE-STATE 29 30 31 t5 DB11 A DB10 A DB9A DB1A DB0A DB11 B DB10 B DB9B DB1B DB0B Figure 33. Serial Interface Timing Diagram When Reading Data on the 20th Rising SCLK Edge with a 40 MHz SCLK Rev. C | Page 25 of 32 THREESTATE THREESTATE 07606-033 SCLK AD7262 Data Sheet CS SCLK 1 2 19 20 21 22 30 31 32 33 34 35 45 46 47 D OUTA DB11 A THREE-STATE DB10 A DB1A DB0 A X DB11 B X DB10 B X DB0B X THREESTATE Figure 34. Reading Data from Both ADCs on One DOUT Line with 47 SCLKs FIRST DATA BIT CLOCKED OUT ON THIS EDGE FIRST DATA BIT READ ON THIS EDGE CS t8 t2 1 t6 2 3 4 5 19 18 20 t7 t3 DOUTA THREE-STATE DOUTB THREE-STATE 21 29 31 t9 t5 t4 30 DB11 A DB10 A DB9 A DB1A DB0 A DB11 B DB10 B DB9 B DB1B DB0 B Figure 35. Serial Interface Timing Diagram When Reading Data on the Falling SCLK Edge with a Slow SCLK Frequency Rev. C | Page 26 of 32 tQUIET THREESTATE THREESTATE 07606-035 SCLK 07606-034 t10 Data Sheet AD7262 CALIBRATION INTERNAL OFFSET CALIBRATION The AD7262/AD7262-5 registers store the offset value that can be accessed easily by the user (see the Reading from a Register section). When the device is calibrating, the differential analog inputs for each respective ADC are shorted together internally and a conversion is performed. A digital code representing the offset is stored internally in the offset registers, and subsequent conversion results have this measured offset removed. The AD7262/AD7262-5 allow the user to calibrate the device offset using the CAL pin. This is achieved by setting the CAL pin to a high logic level, which initiates a calibration on the next CS falling edge. The calibration requires one full conversion cycle, which contains a CS falling edge followed by 19 SCLKs to complete. The CAL pin can remain high for more than one conversion if desired, and the AD7262/AD7262-5 continue to calibrate. When the AD7262/AD7262-5 are calibrated, the calibration results stored in the internal device registers are only relevant for the particular PGA gain selected at the time of calibration. If the PGA gain is changed, the AD7262/AD7262-5 must be recalibrated. If the device is not recalibrated when the PGA gain is changed, the offset for the previous gain setting continues to be removed from the digital output code, which may lead to inaccuracies. The CAL pin should only be driven high when the CS pin is high or after 19 SCLK cycles have elapsed when CS is low (that is, between conversions). The CAL pin must be driven high t12 ns before CS goes low. If the CS pin goes low before the t12 has elapsed, the calibration result is inaccurate for the current conversion, but, provided that the CAL pin remains high, the subsequent calibration conversion is correct. If the CAL pin is set to a logic high state during a conversion, that conversion result is corrupted. The offset range, which can be calibrated for, is ±128 least significant bits at a gain of 1. The maximum offset voltage, which can be calibrated for, is reduced as the gain of the PGA is increased. Table 12 details the maximum offset voltage, which can be removed by the AD7262/AD7262-5 without compromising the available digital output code range. The least significant bit size is AVCC/2BITs, which is 5/4096 or 1.22 mV for the AD7262/AD7262-5. The maximum removable offset voltage is given by Provided that the CAL pin has been held high for a minimum of one conversion, and once t12 and t11 have been adhered to, the calibration is complete after the 19th SCLK cycle, and the CAL pin can be driven to a logic low state. The next CS falling edge after the CAL pin has been driven to a low logic state initiates a conversion of the differential analog input signal for both ADC A and ADC B. ± 128 LSB × Alternatively, one can use the control register to initiate an offset calibration. This is done by setting the CAL bit in the control register to 1. The calibration is then initiated on the next CS falling edge, but the current conversion is corrupted. The ADCs on the AD7262/AD7262-5 must remain fully powered up to complete the internal calibration. Gain Table 12. Offset Range Gain 1 2 3 32 1 Maximum Removable Offset Voltage ±156.16 mV ±78.08 mV ±52.053 mV ±4.88 mV 1 This is the maximum removable offset for PGA gain ≥ 32. t11 t12 CAL 1.22 mV t8 CS 1 t2 t6 2 3 19 20 21 30 31 1 2 t7 Figure 36. Calibration Timing Diagram Rev. C | Page 27 of 32 3 19 20 21 07606-036 SCLK AD7262 Data Sheet ADJUSTING THE OFFSET CALIBRATION REGISTERS SYSTEM GAIN CALIBRATION The internal offset calibration register can be adjusted manually to compensate for any signal path offset from the sensors to the ADC. Here, no internal calibration is required, and the CAL pin can remain at a low logic state. By changing the contents of the offset register, different amounts of offset on the analog input signal can be compensated for. To determine the digital code to be written to the offset register The AD7262/AD7262-5 also allow the user to write to an external gain register, thus enabling the removal of any overall system gain error. Both ADC A and ADC B have independent external gain registers, allowing the user to calibrate independently the gain on both ADC A and ADC B signal paths. The gain calibration feature can be used to implement accurate gain matching between ADC A and ADC B. 1. 2. The system calibration function is used by setting the sensors to which the AD7262/AD7262-5 are connected to a 0 gain state. The AD7262/AD7262-5 convert this analog input to a digital output code, which corresponds to the system gain and is available on the DOUTx pins. This digital output code can then be stored in the appropriate external register. For details on how to write to a register, see the Writing to a Register section and Table 11. 3. 4. Configure the sensor to its offset state. Perform a number of conversions using the AD7262/ AD7262-5. Take the mean digital output code from both DOUTA and DOUTB. This is a 12-bit result and the offset register is 12 bits; thus, the result can be stored directly in the offset register. Write the digital code to the offset registers to calibrate the AD7262/AD7262-5. The gain calibration register contains seven bits of data. By changing the contents of the gain register, different amounts of gain on the analog input signal can be compensated for. The MSB is a sign bit, while the remaining six bits store the multiplication factor, which is used to adjust the analog input range. The gain register value is effectively multiplied by the analog input to scale the conversion result over the full range. Increasing the gain register multiplication factor compensates for a larger analog input range, and decreasing the gain register multiplier compensates for a smaller analog input range. Each bit in the gain calibration register has a resolution of 2.4 × 10−4 V (1/4096). A maximum of 1.538% of the analog range can be calibrated for. The multiplier factor stored in the gain register can be decoded as outlined in Table 13. If a +10 mV offset is present in the analog input signal and the gain of the PGA is 2, the code that needs to be written to the offset register to compensate for the offset is +10 mV = 16.39 = 0000 0001 0000 (1.22 mV / 2) If a − 10 mV offset is present in the analog input signal and the gain of the PGA is 2, the code that needs to be written to the offset register to compensate for the offset is −10 mV = −16.39 = 1000 0001 0000 (305 μV/ 2) The gain registers can be cleared by writing all 0s to each register, as described in the Writing to a Register section. For accurate gain calibration, both the positive and negative full-scale digital output codes should be measured prior to determining the multiplication factor that is written to the gain register. Table 13. Decoding of Multiplication Factors for Gain Calibration Analog Input V VIN max Digital Gain Error LSB 0 LSB Gain Register Code (Sign bit + 6 bits) 0 000000 Multiplier Equation (1 ± x/4096) 1 − 0/4096 Multiplier Value VIN max – 244 μV −2 LSB 0 000001 1 − 1/4096 0.999755859 VIN max − (63 × 244 μV) −126 LSB 0 111111 1 − 63/4096 0.98461914 VIN max 0 LSB 1 000000 1 + 0/4096 1 VIN max + 244 μV +2 LSB 1 000001 1 + 1/4096 1.000244141 VIN max + (63 × 244 μV) +126 LSB 1 111111 1 + 63/4096 1.015380859 Rev. C | Page 28 of 32 1 Comments Sign bit = 0, which implies negative sign in multiplier equation Sign bit = 0, which implies negative sign in multiplier equation Sign bit = 0, which implies negative sign in multiplier equation Sign bit = 1, which implies plus sign in multiplier equation Sign bit = 1, which implies plus sign in multiplier equation Sign bit = 1, which implies plus sign in multiplier equation Data Sheet AD7262 MICROPROCESSOR INTERFACING The serial interface on the AD7262/AD7262-5 allows the parts to connect directly to a range of different microprocessors. This section explains how to interface the AD7262/AD7262-5 with the Analog Devices, Inc., Blackfin® DSP, the ADSP-BF531. AD7262/AD7262-5 TO ADSP-BF531 The ADSP-BF531 and the rest of the Blackfin microprocessor family of DSPs interface directly to the AD7262/AD7262-5 without any glue logic required. The VDRIVE pin of the AD7262/ AD7262-5 takes the same supply voltage as that of the ADSP-BF531. This allows the ADC to operate at a higher supply voltage than its serial interface and, therefore, the ADSP-BF531, if necessary. The availability of secondary receive registers on the serial ports of the Blackfin DSPs means only one serial port is necessary to read from both DOUT pins simultaneously. Figure 37 shows both DOUTA and DOUTB of the AD7262/AD7262-5 connected to Serial Port 0 of the ADSP-BF531. The SPORT0 Receive Configuration 1 register and SPORT0 Receive Configuration 2 register must be set up as outlined in Table 14 and Table 15. DOUTA SERIAL DEVICE A (PRIMARY) SCLK VDRIVE Setting RXSE = 1 ADSP-BF5311 SPORT0 DR0PRI RFS0 SERIAL DEVICE B (SECONDARY) DR0SEC VDD 1ADDITIONAL PINS OMITTED FOR CLARITY. Description Sample data with falling edge of RSCLK Active low frame signal Frame every word Internal receive frame sync (RFS) used Receive MSB first Zero fill Internal receive clock Receive enabled 31-bit data-word Table 15. The SPORT0 Receive Configuration 2 Register (SPORT0_RCR2) RCLK0 CS DOUTB Setting RCKFE = 1 LRFS = 1 RFSR = 1 IRFS = 1 RLSBIT = 0 RDTYPE = 00 IRCLK = 1 RSPEN = 1 SLEN = 11110 TFSR = RFSR = 1 07606-037 AD72621 Table 14. The SPORT0 Receive Configuration 1 Register (SPORT0_RCR1) Figure 37. Interfacing the AD7262 to the ADSP-BF531 Rev. C | Page 29 of 32 Description Secondary side enabled AD7262 Data Sheet APPLICATION HINTS GROUNDING AND LAYOUT The analog and digital supplies to the AD7262/AD7262-5 are independent and separately pinned out to minimize coupling between the analog and digital sections of the device. The printed circuit board (PCB) that houses the AD7262/AD7262-5 should be designed so that the analog and digital sections are separated and confined to certain areas of the board. This design facilitates the use of ground planes that can be easily separated. To provide optimum shielding for ground planes, a minimum etch technique is generally best. All five AGND pins of the AD7262/AD7262-5 should be sunk in the AGND plane. Digital and analog ground planes should be joined in only one place. If the AD7262/AD7262-5 are in a system where multiple devices require an AGND to DGND connection, the connection should still be made at one point only, a star ground point, that should be established as close as possible to the ground pins on the AD7262/AD7262-5. Avoid running digital lines under the device because this couples noise onto the die. However, the analog ground plane should be allowed to run under the AD7262/AD7262-5 to avoid noise coupling. The power supply lines to the AD7262/ AD7262-5 should use as large a trace as possible to provide low impedance paths and reduce the effects of glitches on the power supply line. To avoid radiating noise to other sections of the board, fast switching signals, such as clocks, should be shielded with digital ground, and clock signals should never run near the analog inputs. Avoid crossover of digital and analog signals. To reduce the effects of feedthrough within the board, traces on opposite sides of the board should run at right angles to each other. A microstrip technique is the best method but is not always possible with a double-sided board. In this technique, the component side of the board is dedicated to ground planes, while signals are placed on the solder side. Good decoupling is also important. All analog supplies should be decoupled with 10 μF tantalum capacitors in parallel with 100 nF capacitors to GND. To achieve the best results from these decoupling components, they must be placed as close as possible to the device, ideally right up against the device. The 0.1 μF capacitors should have low effective series resistance (ESR) and effective series inductance (ESI), such as the common ceramic types or surface-mount types. These low ESR and ESI capacitors provide a low impedance path to ground at high frequencies to handle transient currents due to internal logic switching. PCB DESIGN GUIDELINES FOR LFCSP The land on the chip scale packages (CP-48-1) are rectangular. The PCB pad for these should be 0.1 mm longer than the package land length and 0.05 mm wider than the package land width, thereby having a portion of the pad exposed. To ensure that the solder joint size is maximized, the land should be centered on the pad. The bottom of the chip scale package has a thermal pad. The thermal pad on the PCB should be at least as large as the exposed pad. On the PCB, there should be a clearance of at least 0.25 mm between the thermal pad and the inner edges of the pad pattern to ensure that shorting is avoided. To improve thermal performance of the package, use thermal vias on the PCB, incorporating them into the thermal pad at 1.2 mm pitch grid. The via diameter should be between 0.3 mm and 0.33 mm, and the via barrel should be plated with 1 oz. copper to plug the via. The user should connect the PCB thermal pad to AGND. Rev. C | Page 30 of 32 Data Sheet AD7262 OUTLINE DIMENSIONS 7.10 7.00 SQ 6.90 0.30 0.23 0.18 0.60 MAX 0.60 MAX 37 48 1 36 PIN 1 INDICATOR 6.85 6.75 SQ 6.65 0.50 REF 5.25 5.10 SQ 4.95 EXPOSED PAD 12 25 12° MAX SIDE VIEW 0.80 MAX 0.65 TYP 0.20 MIN 5.50 REF FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF SEATING PLANE PKG-001049 BOTTOM VIEW 11-13-2017-B 1.00 0.85 0.80 13 24 0.50 0.40 0.30 TOP VIEW PIN 1 INDICATOR COMPLIANT TO JEDEC STANDARDS MO-220-VKKD-2 Figure 38. 48-Lead Lead Frame Chip Scale Package [LFCSP] 7 mm × 7 mm Body and 0.85 mm Package Height (CP-48-1) Dimensions shown in millimeters 9.20 9.00 SQ 8.80 1.60 MAX 1 37 48 36 PIN 1 1.45 1.40 1.35 0.15 0.05 0.20 0.09 7° 3.5° 0° 0.08 COPLANARITY SEATING PLANE VIEW A 7.20 7.00 SQ 6.80 TOP VIEW (PINS DOWN) 12 13 VIEW A 0.50 BSC LEAD PITCH 24 25 0.27 0.22 0.17 ROTATED 90° CCW COMPLIANT TO JEDEC STANDARDS MS-026-BBC 051706-A 0.75 0.60 0.45 Figure 39. 48-Lead Low Profile Quad Flat Package [LQFP] (ST-48) Dimensions shown in millimeters ORDERING GUIDE Model 1 AD7262BCPZ-RL7 AD7262BSTZ AD7262BSTZ-RL7 AD7262BSTZ-5 AD7262BSTZ-5-RL7 EVAL-AD7262EDZ EVAL-CED1Z 1 Temperature Range −40°C to +105°C −40°C to +105°C −40°C to +105°C −40°C to +105°C −40°C to +105°C Package Description 48-Lead Lead Frame Chip Scale Package [LFCSP] 48-Lead Low Profile Quad Flat Package [LQFP] 48-Lead Low Profile Quad Flat Package [LQFP] 48-Lead Low Profile Quad Flat Package [LQFP] 48-Lead Low Profile Quad Flat Package [LQFP] Evaluation Board Development Board Z = RoHS Compliant Part. Rev. C | Page 31 of 32 Package Option CP-48-1 ST-48 ST-48 ST-48 ST-48 AD7262 Data Sheet NOTES ©2008–2018 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D07606-0-1/18(C) Rev. C | Page 32 of 32