18-Bit, 2.5 LSB INL, 100 kSPS SAR ADC
AD7678
FUNCTIONAL BLOCK DIAGRAM
FEATURES
18-bit resolution with no missing codes
No pipeline delay (SAR architecture)
Differential input range: ±VREF (VREF up to 5 V)
Throughput: 100 kSPS
INL: ±2.5 LSB max (±9.5 ppm of full scale)
Dynamic range: 103 dB typ (VREF = 5 V)
S/(N+D): 100 dB typ @ 2 kHz (VREF = 5 V)
Parallel (18-,16-, or 8-bit bus) and serial 5 V/3 V interface
SPI®/QSPI™/MICROWIRE™/DSP compatible
On-board reference buffer
Single 5 V supply operation
Power dissipation: 18 mW @ 100 kSPS
180 µW @ 1 kSPS
48-lead LQFP or 48-lead LFCSP package
Pin-to-pin compatible upgrade of AD7674/AD7676/AD7679
APPLICATIONS
CT scanners
High dynamic data acquisition
Geophone and hydrophone sensors
Σ-∆ replacement (low power, multichannel)
Instrumentation
Spectrum analysis
Medical instruments
GENERAL DESCRIPTION
The AD7678 is an 18-bit, 100 kSPS, charge redistribution SAR,
fully differential analog-to-digital converter that operates on a
single 5 V power supply. The part contains a high speed 18-bit
sampling ADC, an internal conversion clock, an internal
reference buffer, error correction circuits, and both serial and
parallel system interface ports.
The part is available in 48-lead LQFP or 48-lead LFCSP
packages with operation specified from –40°C to +85°C.
PDBUF
REF REFGND
AGND
AVDD
IN–
OVDD
AD7678
OGND
SERIAL
PORT
REFBUFIN
IN+
DVDD DGND
18
SWITCHED
CAP DAC
D[17:0]
BUSY
PARALLEL
INTERFACE
CLOCK
PD
RESET
RD
CS
CONTROL LOGIC AND
CALIBRATION CIRCUITRY
MODE0
MODE1
CNVST
03084–0–001
Figure 1. Functional Block Diagram
Table 1. PulSAR Selection
Type/kSPS
PseudoDifferential
True Bipolar
True
Differential
18-Bit
Multichannel/
Simultaneous
100–250
AD7651
AD7660/AD7661
AD7663
AD7675
500–570
AD7650/AD7652
AD7664/AD7666
AD7665
AD7676
AD7678
AD7679
AD7654
AD7655
800–
1000
AD7653
AD7667
AD7671
AD7677
AD7674
PRODUCT HIGHLIGHTS
1.
High Resolution, Fast Throughput.
The AD7678 is a 100 kSPS, charge redistribution, 18-bit
SAR ADC (no latency).
2.
Excellent Accuracy.
The AD7678 has a maximum integral nonlinearity of
2.5 LSB with no missing 18-bit codes.
3.
Serial or Parallel Interface.
Versatile parallel (18-, 16-, or 8-bit bus) or 2-wire serial
interface arrangement compatible with both 3 V and
5 V logic.
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice.
No license is granted by implication or otherwise under any patent or patent rights of Analog
Devices. Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2003–2020 Analog Devices, Inc. All rights reserved.
AD7678
TABLE OF CONTENTS
Specifications .................................................................................... 3
Digital Interface .......................................................................... 20
Timing Specifications ...................................................................... 5
Parallel Interface......................................................................... 20
Absolute Maximum Ratings ........................................................... 7
Serial Interface ............................................................................ 20
ESD Caution.................................................................................. 7
Master Serial Interface ............................................................... 21
Pin Configuration and Function Descriptions ............................ 8
Slave Serial Interface .................................................................. 22
Definition of Specifications........................................................... 11
Microprocessor Interfacing ...................................................... 24
Typical Performance Characteristics ........................................... 12
Application Hints ........................................................................... 25
Circuit Information........................................................................ 15
Layout .......................................................................................... 25
Converter Operation.................................................................. 15
Evaluating the AD7678’s Performance ................................... 25
Typical Connection Diagram ................................................... 17
Outline Dimensions ....................................................................... 26
Power Dissipation versus Throughput ................................... 19
Ordering Guide .......................................................................... 26
Conversion Control ................................................................... 19
REVISION HISTORY
8/2020—Rev. A to Rev. B
Changed CP-48-1 to CP-48-4 ...................................... Throughout
Updated Outline Dimensions ....................................................... 26
Changes to Ordering Guide .......................................................... 26
6/2009—Rev. 0 to Rev. A
Removed Endnote 3 from DC Accuracy; Zero Error, TMIN to
TMAX Parameter; Table 2 .................................................................. 3
Changes to Endnote 3, Table 2 ........................................................4
Moved ESD Caution .........................................................................7
Changes to Figure 4 and Table 6 .....................................................8
Changes to Evaluating the AD7678’s Performance Section .... 25
Updated Outline Dimensions ...................................................... 26
Changes to Ordering Guide .......................................................... 26
8/2003—Revision 0: Initial Version
Rev. B | Page 2 of 28
AD7678
SPECIFICATIONS
Table 2. –40°C to +85°C, VREF = 4.096 V, AVDD = DVDD = 5 V, OVDD = 2.7 V to 5.25 V, unless otherwise noted.
Parameter
RESOLUTION
ANALOG INPUT
Voltage Range
Operating Input Voltage
Analog Input CMRR
Input Current
Input Impedance 1
THROUGHPUT SPEED
Complete Cycle
Throughput Rate
DC ACCURACY
Integral Linearity Error
Differential Linearity Error
No Missing Codes
Transition Noise
Zero Error, TMIN to TMAX
Zero Error Temperature Drift
Gain Error, TMIN to TMAX 3
Gain Error Temperature Drift
Power Supply Sensitivity
AC ACCURACY
Signal-to-Noise
Dynamic Range
Spurious-Free Dynamic Range
Total Harmonic Distortion
Signal-to-(Noise + Distortion)
–3 dB Input Bandwidth
SAMPLING DYNAMICS
Aperture Delay
Aperture Jitter
Transient Response
Overvoltage Recovery
REFERENCE
External Reference Voltage Range
REF Voltage with Reference Buffer
Reference Buffer Input Voltage Range
REFBUFIN Input Current
REF Current Drain
Conditions
Min
18
VIN+ – VIN–
VIN+, VIN– to AGND
fIN = 100 kHz
100 kSPS Throughput
–VREF
–0.1
Typ
Max
Unit
Bits
+VREF
AVDD + 0.1
V
V
dB
µA
10
100
µs
kSPS
+2.5
+1.75
LSB 2
LSB
Bits
LSB
LSB
ppm/°C
% of FSR
ppm/°C
LSB
65
4
0
–2.5
–1
18
VREF = 5 V
0.7
–40
–0.048
AVDD = 5 V ± 5%
fIN = 2 kHz, VREF = 5 V
VREF = 4.096 V
fIN = 10 kHz, VREF = 4.096 V
fIN = 45 kHz, VREF = 4.096 V
VIN+ = VIN– = VREF/2 = 2.5 V
fIN = 2 kHz
fIN = 10 kHz
fIN = 45 kHz
fIN = 2 kHz
fIN = 10 kHz
fIN = 45 kHz
fIN = 2 kHz
fIN = 2 kHz, –60 dB Input
98
±40
±0.5
See Note 3
±1.6
±4
101
100
99.5
98
103
120
117
110
–118
–115
–110
100
41
900
dB 4
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
kHz
2
5
ns
ps rms
µs
µs
Full-Scale Step
REF
REFBUFIN = 2.5 V
REFBUFIN
100 kSPS Throughput
Rev. B | Page 3 of 28
+0.048
8.5
8.5
3
4.05
1.8
–1
4.096
4.096
2.5
42
AVDD + 0.1
4.15
2.6
+1
V
V
V
µA
µA
AD7678
Parameter
DIGITAL INPUTS
Logic Levels
VIL
VIH
IIL
IIH
DIGITAL OUTPUTS
Data Format 5
Pipeline Delay 6
VOL
VOH
POWER SUPPLIES
Specified Performance
AVDD
DVDD
OVDD
Operating Current
AVDD
DVDD 8
OVDD8
Conditions
Min
–0.3
2.0
–1
–1
ISINK = 1.6 mA
ISOURCE = –500 µA
4.75
4.75
2.7
100 kSPS Throughput
PDBUF High
TMIN to TMAX
Max
Unit
+0.8
DVDD + 0.3
+1
+1
V
V
µA
µA
0.4
V
V
5.25
5.25
DVDD + 0.3 7
V
V
V
OVDD – 0.6
5
5
2.6
1
40
18
180
31
PDBUF High @ 100 kSPS
PDBUF High @ 1 kSPS
PDBUF Low @ 100 kSPS
TEMPERATURE RANGE 9
Specified Performance
Typ
–40
26
+85
mA
mA
µA
mW
µW
mW
°C
See the Analog Inputs section.
LSB means Least Significant Bit. With the ±4.096 V input range, 1 LSB is 31.25 µV.
3
See the Definition of Specifications section. The nominal gain error is not centered at zero and is −0.029% of FSR. This specification is the deviation from this nominal
value. These specifications do not include the error contribution from the external reference, but do include the error contribution from the reference buffer if used.
4
All specifications in dB are referred to a full-scale input, FS. Tested with an input signal at 0.5 dB below full scale, unless otherwise specified.
5
Data format parallel or serial 18-bit.
6
Conversion results are available immediately after completed conversion.
7
The maximum should be the minimum of 5.25 V and DVDD + 0.3 V.
8
Tested in Parallel Reading mode.
9
Contact factory for extended temperature range.
1
2
Rev. B | Page 4 of 28
AD7678
TIMING SPECIFICATIONS
Table 3. –40°C to +85°C, AVDD = DVDD = 5 V, OVDD = 2.7 V to 5.25 V, unless otherwise noted.
Parameter
Refer to Figure 27 and Figure 28
Convert Pulse Width
Time between Conversions
CNVST LOW to BUSY HIGH Delay
BUSY HIGH All Modes Except Master Serial Read after Convert
Aperture Delay
End of Conversion to BUSY LOW Delay
Conversion Time
Acquisition Time
RESET Pulsewidth
Refer to Figure 29, Figure 30, and Figure 31 (Parallel Interface Modes)
CNVST LOW to Data Valid Delay
Data Valid to BUSY LOW Delay
Bus Access Request to Data Valid
Bus Relinquish Time
Refer to Figure 33 and Figure 34 (Master Serial Interface Modes) 1
CS LOW to SYNC Valid Delay
CS LOW to Internal SCLK Valid Delay
CS LOW to SDOUT Delay
CNVST LOW to SYNC Delay
SYNC Asserted to SCLK First Edge Delay 2
Internal SCLK Period2
Internal SCLK HIGH2
Internal SCLK LOW2
SDOUT Valid Setup Time2
SDOUT Valid Hold Time2
SCLK Last Edge to SYNC Delay2
CS HIGH to SYNC HI-Z
CS HIGH to Internal SCLK HI-Z
CS HIGH to SDOUT HI-Z
BUSY HIGH in Master Serial Read after Convert2
CNVST LOW to SYNC Asserted Delay
SYNC Deasserted to BUSY LOW Delay
Refer to Figure 35 and Figure 36 (Slave Serial Interface Modes)
External SCLK Setup Time
External SCLK Active Edge to SDOUT Delay
SDIN Setup Time
SDIN Hold Time
External SCLK Period
External SCLK HIGH
External SCLK LOW
Symbol
Min
t1
t2
t3
t4
t5
t6
t7
t8
t9
10
10
t10
t11
t12
t13
t14
t15
t16
t17
t18
t19
t20
t21
t22
t23
t24
t25
t26
t27
t28
t29
t30
t31
t32
t33
t34
t35
t36
t37
Typ
35
1.5
2
10
1.5
8.5
10
1.5
20
45
15
5
10
10
10
525
3
25
12
7
4
2
3
40
10
10
10
See Table 4
1.5
25
5
3
5
5
25
10
10
In serial interface modes, the SYNC, SCLK, and SDOUT timings are defined with a maximum load CL of 10 pF; otherwise, the load is 60 pF maximum.
In Serial Master Read during Convert mode. See Table 4 for Serial Master Read after Convert mode.
1
2
Rev. B | Page 5 of 28
Max
Unit
ns
µs
ns
µs
ns
ns
µs
µs
ns
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
µs
ns
18
ns
ns
ns
ns
ns
ns
ns
AD7678
Table 4. Serial Clock Timings in Master Read after Convert
DIVSCLK[1]
DIVSCLK[0]
SYNC to SCLK First Edge Delay Minimum
Internal SCLK Period Minimum
Internal SCLK Period Maximum
Internal SCLK HIGH Minimum
Internal SCLK LOW Minimum
SDOUT Valid Setup Time Minimum
SDOUT Valid Hold Time Minimum
SCLK Last Edge to SYNC Delay Minimum
Busy High Width Maximum
Symbol
t18
t19
t19
t20
t21
t22
t23
t24
t28
Rev. B | Page 6 of 28
0
0
3
25
40
12
7
4
2
3
2.25
0
1
17
60
80
22
21
18
4
60
3
1
0
17
120
160
50
49
18
30
140
4.5
1
1
17
240
320
100
99
18
89
300
7.5
Unit
ns
ns
ns
ns
ns
ns
ns
ns
µs
AD7678
ABSOLUTE MAXIMUM RATINGS
Table 5. AD7678 Absolute Maximum Ratings 1
Parameter
Analog Inputs
IN+ 2, IN–2, REF, REFBUFIN, REFGND
to AGND
Ground Voltage Differences
AGND, DGND, OGND
Supply Voltages
AVDD, DVDD, OVDD
AVDD to DVDD, AVDD to OVDD
DVDD to OVDD
Digital Inputs
Internal Power Dissipation 3
Internal Power Dissipation 4
Junction Temperature
Storage Temperature Range
Lead Temperature Range
(Soldering 10 sec)
Rating
1.6mA
AVDD + 0.3 V to
AGND – 0.3 V
IOL
TO OUTPUT
PIN
1.4V
CL
60pF1
±0.3 V
500µA
–0.3 V to +7 V
±7 V
–0.3 V to +7 V
–0.3 V to DVDD + 0.3 V
700 mW
2.5 W
150°C
–65°C to +150°C
IOH
1 IN
SERIAL INTERFACE MODES,THE SYNC, SCLK, AND
SDOUT TIMINGS ARE DEFINED WITH A MAXIMUM LOAD
CL OF 10pF; OTHERWISE,THE LOAD IS 60pF MAXIMUM.
03084–0–002
Figure 2. Load Circuit for Digital Interface Timing,
SDOUT, SYNC, SCLK Outputs, CL = 10 pF
2V
0.8V
tDELAY
300°C
tDELAY
2V
0.8V
2V
0.8V
03084–0–003
Stresses above those listed under Absolute Maximum Ratings may cause
permanent damage to the device. This is a stress rating only; functional
operation of the device at these or any other conditions above those
indicated in the operational section of this specification is not implied.
Exposure to absolute maximum rating conditions for extended periods may
affect device reliability.
2
See Analog Inputs section.
3
Specification is for device in free air: 48-Lead LQFP: θJA = 91°C/W,
θJC = 30°C/W.
4
Specification is for device in free air: 48-Lead LFCSP: θJA = 26°C/W.
1
Figure 3. Voltage Reference Levels for Timing
ESD CAUTION
Rev. B | Page 7 of 28
AD7678
REF
REFGND
IN–
NC
NC
NC
IN+
AGND
NC
REFBUFIN
AVDD
PDBUF
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
48 47 46 45 44 43 42 41 40 39 38 37
AGND 1
AVDD 2
PIN 1
IDENTIFIER
36
AGND
35
MODE0 3
34
CNVST
PD
MODE1 4
D0/OB/2C 5
NC 6
33
RESET
32
CS
31
30
RD
DGND
AD7678
TOP VIEW
(Not to Scale)
NC 7
D1/A0 8
29
BUSY
D2/A1 9
28
D17
D3 10
27
D16
D4/DIVSCLK[0] 11
26
D15
D5/DIVSCLK[1] 12
25
D14
NOTES
1. NC = NO CONNECT.
2. THE EXPOSED PAD IS INTERNALLY CONNECTED TO AGND. THIS
CONNECTION IS NOT REQUIRED TO MEET THE ELECTRICAL
PERFORMANCES; HOWEVER, FOR INCREASED RELIABILITY OF
THE SOLDER JOINTS, IT IS RECOMMENDED THAT THE PAD BE
SOLDERED TO THE ANALOG GROUND OF THE SYSTEM.
03084-004
D13/RDERROR
D12/SYNC
D11/SCLK
D10/SDOUT
DGND
DVDD
OVDD
OGND
D9/RDC/SDIN
D8/INVSCLK
D6/EXT/INT
D7/INVSYNC
13 14 15 16 17 18 19 20 21 22 23 24
Figure 4. 48-Lead LQFP and 48-Lead LFCSP (ST-48 and CP-48) Pin Configuration
Table 6. Pin Function Descriptions
Pin No.
1, 44
2, 47
3
4
Mnemonic
AGND
AVDD
MODE0
MODE1
Type 1
P
P
DI
DI
5
D0/OB/2C
DI/O
6, 7,
40–42,
45
8
NC
D1/A0
DI/O
9
D2/A1
DI/O
10
D3
DO
11, 12
D[4:5]or
DIVSCLK[0:1]
DI/O
Description
Analog Power Ground Pin.
Input Analog Power Pins. Nominally 5 V.
Data Output Interface Mode Selection.
Data Output Interface Mode Selection:
Interface MODE # MODE1 MODE0 Description
0
0
0
18-Bit Interface
1
0
1
16-Bit Interface
2
1
0
Byte Interface
3
1
1
Serial Interface
When MODE = 0 (18-bit interface mode), this pin is Bit 0 of the parallel port data output bus and the
data coding is straight binary. In all other modes, this pin allows choice of straight binary/binary twos
complement. When OB/2C is HIGH, the digital output is straight binary; when LOW, the MSB is
inverted, resulting in a twos complement output from its internal shift register.
No Connect.
When MODE = 0 (18-bit interface mode), this pin is Bit 1 of the parallel port data output bus. In all
other modes, this input pin controls the form in which data is output, as shown in Table 7.
When MODE = 0 or 1 (18-bit or 16-bit interface mode), this pin is Bit 2 of the parallel port data output
bus. In all other modes, this input pin controls the form in which data is output, as shown in Table 7.
In all modes except MODE = 3, this output is used as Bit 3 of the parallel port data output bus. This pin
is always an output, regardless of the interface mode.
In all modes except MODE = 3, these pins are Bit 4 and Bit 5 of the parallel port data output bus.
When MODE = 3 (serial mode), EXT/INT is LOW, and RDC/SDIN is LOW (serial master read after
convert), these inputs, part of the serial port, are used to slow down, if desired, the internal serial clock
that clocks the data output. In other serial modes, these pins are not used.
Rev. B | Page 8 of 28
AD7678
Pin No.
13
Mnemonic
D6
or EXT/INT
Type 1
DI/O
14
D7
or INVSYNC
DI/O
15
D8
or INVSCLK
DI/O
16
D9
or RDC/SDIN
DI/O
17
18
OGND
OVDD
P
P
19
20
21
DVDD
DGND
D10
or SDOUT
P
P
DO
22
D11
or SCLK
DI/O
23
D12
or SYNC
DO
24
D13
or RDERROR
DO
25–28
D[14:17]
DO
29
BUSY
DO
30
31
32
DGND
RD
CS
P
DI
DI
33
RESET
DI
Description
In all modes except MODE = 3, this output is used as Bit 6 of the parallel port data output bus.
When MODE = 3 (serial mode), this input, part of the serial port, is used as a digital select input for
choosing the internal data clock or an external data clock. With EXT/INT tied LOW, the internal clock is
selected on the SCLK output. With EXT/INT set to a logic HIGH, output data is synchronized to an
external clock signal connected to the SCLK input.
In all modes except MODE = 3, this output is used as Bit 7 of the parallel port data output bus.
When MODE = 3 (serial mode), this input, part of the serial port, is used to select the active state of the
SYNC signal. When LOW, SYNC is active HIGH. When HIGH, SYNC is active LOW.
In all modes except MODE = 3, this output is used as Bit 8 of the parallel port data output bus.
When MODE = 3 (serial mode), this input, part of the serial port, is used to invert the SCLK signal. It is
active in both master and slave modes.
In all modes except MODE = 3, this output is used as Bit 9 of the parallel port data output bus.
When MODE = 3 (serial mode), this input, part of the serial port, is used as either an external data
input or a read mode selection input depending on the state of EXT/INT. When EXT/INT is HIGH,
RDC/SDIN could be used as a data input to daisy-chain the conversion results from two or more ADCs
onto a single SDOUT line. The digital data level on SDIN is output on SDOUT with a delay of 18 SCLK
periods after the initiation of the read sequence. When EXT/INT is LOW, RDC/SDIN is used to select the
read mode. When RDC/SDIN is HIGH, the data is output on SDOUT during conversion. When
RDC/SDIN is LOW, the data can be output on SDOUT only when the conversion is complete.
Input/Output Interface Digital Power Ground.
Output Interface Digital Power. Nominally at the same supply as the host interface (5 V or 3 V). Should
not exceed DVDD by more than 0.3 V.
Digital Power. Nominally at 5 V.
Digital Power Ground.
In all modes except MODE = 3, this output is used as Bit 10 of the parallel port data output bus.
When MODE = 3 (serial mode), this output, part of the serial port, is used as a serial data output
synchronized to SCLK. Conversion results are stored in an on-chip register. The AD7678 provides the
conversion result, MSB first, from its internal shift register. The data format is determined by the logic
level of OB/2C. In serial mode when EXT/INT is LOW, SDOUT is valid on both edges of SCLK. In serial
mode when EXT/INT is HIGH and INVSCLK is LOW, SDOUT is updated on the SCLK rising edge and is
valid on the next falling edge; if INVSCLK is HIGH, SDOUT is updated on the SCLK falling edge and is
valid on the next rising edge.
In all modes except MODE = 3, this output is used as Bit 11 of the parallel port data output bus.
When MODE = 3 (serial mode), this pin, part of the serial port, is used as a serial data clock input or
output, depending upon the logic state of the EXT/INT pin. The active edge where the data SDOUT is
updated depends upon the logic state of the INVSCLK pin.
In all modes except MODE = 3, this output is used as Bit 12 of the parallel port data output bus.
When MODE = 3 (serial mode), this output, part of the serial port, is used as a digital output frame
synchronization for use with the internal data clock (EXT/INT = Logic LOW). When a read sequence is
initiated and INVSYNC is LOW, SYNC is driven HIGH and remains HIGH while the SDOUT output is
valid. When a read sequence is initiated and INVSYNC is HIGH, SYNC is driven LOW and remains LOW
while SDOUT output is valid.
In all modes except MODE = 3, this output is used as Bit 13 of the parallel port data output bus.
In MODE = 3 (serial mode) and when EXT/INT is HIGH, this output, part of the serial port, is used as an
incomplete read error flag. In slave mode, when a data read is started and not complete when the
following conversion is complete, the current data is lost and RDERROR is pulsed high.
Bit 14 to Bit 17 of the Parallel Port Data Output Bus. These pins are always outputs regardless of the
interface mode.
Busy Output. Transitions HIGH when a conversion is started. Remains HIGH until the conversion is
complete and the data is latched into the on-chip shift register. The falling edge of BUSY could be
used as a data ready clock signal.
Must Be Tied to Digital Ground.
Read Data. When CS and RD are both LOW, the interface parallel or serial output bus is enabled.
Chip Select. When CS and RD are both LOW, the interface parallel or serial output bus is enabled. CS is
also used to gate the external clock.
Reset Input. When set to a logic HIGH, reset the AD7678. Current conversion, if any, is aborted. If not
used, this pin could be tied to DGND.
Rev. B | Page 9 of 28
AD7678
Pin No.
34
Mnemonic
PD
Type 1
DI
35
CNVST
DI
36
37
AGND
REF
P
AI
38
39
43
46
REFGND
IN–
IN+
REFBUFIN
AI
AI
AI
AI
48
PDBUF
DI
49
(EPAD)
Exposed Pad
(EPAD)
Description
Power-Down Input. When set to a logic HIGH, power consumption is reduced and conversions are
inhibited after the current one is completed.
Start Conversion. If CNVST is held HIGH when the acquisition phase (t8) is complete, the next falling
edge on CNVST puts the internal sample/hold into the hold state and initiates a conversion. If CNVST
is held LOW when the acquisition phase is complete, the internal sample/hold is put into the hold
state and a conversion is started immediately.
Must Be Tied to Analog Ground.
Reference Input Voltage and Internal Reference Buffer Output. Apply an external reference on this pin
if the internal reference buffer is not used. Should be decoupled effectively with or without the
internal buffer.
Reference Input Analog Ground.
Differential Negative Analog Input.
Differential Positive Analog Input.
Reference Buffer Input Voltage. The internal reference buffer has a fixed gain. It outputs 4.096 V
typically when 2.5 V is applied on this pin.
Allows Choice of Buffering Reference. When LOW, buffer is selected. When HIGH, buffer is switched
off.
The exposed pad is internally connected to AGND. This connection is not required to meet the
electrical performances; however, for increased reliability of the solder joints, it is recommended that
the pad be soldered to the analog ground of the system.
AI = Analog Input; AO = Analog Output; DI = Digital Input; DI/O = Bidirectional Digital; DO = Digital Output; P = Power.
1
Table 7. Data Bus Interface Definitions
MODE
MODE1
MODE0
D0/OB/2C
D1/A0
D2/A1
D[3]
D[4:9]
D[10:11]
D[12:15]
D[16:17]
Description
0
1
0
0
0
1
R[0]
OB/2C
R[1]
A0:0
R[2]
R[2]
R[3]
R[3]
R[4:9]
R[4:9]
R[10:11]
R[10:11]
R[12:15]
R[12:15]
R[16:17]
R[16:17]
18-Bit Parallel
16-Bit High Word
1
0
1
OB/2C
A0:1
R[0]
R[1]
2
1
0
OB/2C
A0:0
A1:0
All Hi-Z
R[10:11]
R[12:15]
R[16:17]
2
1
0
OB/2C
A0:0
A1:1
All Hi-Z
R[2:3]
R[4:7]
R[8:9]
2
1
0
OB/2C
A0:1
A1:0
All Hi-Z
R[0:1]
2
1
0
OB/2C
A0:1
A1:1
All Hi-Z
3
1
1
OB/2C
All Hi-Z
All Zeros
16-Bit Low Word
All Zeros
All Zeros
Serial Interface
R[0:17] is the 18-bit ADC value stored in its output register.
Rev. B | Page 10 of 28
R[0:1]
8-Bit HIGH Byte
8-Bit MID Byte
8-Bit LOW Byte
8-Bit LOW Byte
Serial Interface
AD7678
DEFINITION OF SPECIFICATIONS
Integral Nonlinearity Error (INL)
Total Harmonic Distortion (THD)
Linearity error refers to the deviation of each individual code
from a line drawn from negative full scale through positive full
scale. The point used as negative full scale occurs ½ LSB before
the first code transition. Positive full scale is defined as a level
1½ LSB beyond the last code transition. The deviation is
measured from the middle of each code to the true straight line.
THD is the ratio of the rms sum of the first five harmonic
components to the rms value of a full-scale input signal, and is
expressed in decibels.
Differential Nonlinearity Error (DNL)
In an ideal ADC, code transitions are 1 LSB apart. Differential
nonlinearity is the maximum deviation from this ideal value. It
is often specified in terms of resolution for which no missing
codes are guaranteed.
Gain Error
The first transition (from 000…00 to 000…01) should occur for
an analog voltage ½ LSB above the nominal –full scale
(–4.095991 V for the ±4.096 V range). The last transition (from
111…10 to 111…11) should occur for an analog voltage
1½ LSB below the nominal full scale (4.095977 V for the
±4.096 V range). The gain error is the deviation of the difference between the actual level of the last transition and the
actual level of the first transition from the difference between
the ideal levels.
Zero Error
The zero error is the difference between the ideal midscale
input voltage (0 V) from the actual voltage producing the
midscale output code.
Dynamic Range
Dynamic range is the ratio of the rms value of the full scale to
the rms noise measured with the inputs shorted together. The
value for dynamic range is expressed in decibels.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the actual input signal to
the rms sum of all other spectral components below the
Nyquist frequency, excluding harmonics and dc. The value for
SNR is expressed in decibels.
Signal-to-(Noise + Distortion) Ratio (S/[N+D])
S/(N+D) is the ratio of the rms value of the actual input signal
to the rms sum of all other spectral components below the
Nyquist frequency, including harmonics but excluding dc. The
value for S/(N+D) is expressed in decibels.
Aperture Delay
Aperture delay is a measure of the acquisition performance and
is measured from the falling edge of the CNVST input to when
the input signal is held for a conversion.
Transient Response
Transient response is the time required for the AD7678 to
achieve its rated accuracy after a full-scale step function is
applied to its input.
Spurious-Free Dynamic Range (SFDR)
SFDR is the difference, in decibels (dB), between the rms
amplitude of the input signal and the peak spurious signal.
Effective Number of Bits (ENOB)
ENOB is a measurement of the resolution with a sine wave
input, and is expressed in bits. It is related to S/(N+D) by the
following formula:
ENOB = (S/[N+D]dB – 1.76)/6.02
Rev. B | Page 11 of 28
AD7678
TYPICAL PERFORMANCE CHARACTERISTICS
2.5
2.0
2.0
1.5
1.5
1.0
DNL-LSB (18-Bit)
INL-LSB (18-Bit)
1.0
0.5
0
–0.5
0.5
0
–1.0
–1.5
–0.5
–2.0
–2.5
0
65536
131072
CODE
196608
–1.0
262144
0
65536
131072
CODE
03084-0-005
Figure 5. Integral Nonlinearity vs. Code
196608
262144
03084-0-008
Figure 8. Differential Nonlinearity vs. Code
90000
70000
83610
VREF = 5V
60158 59966
VREF = 5V
80000
60000
70000
50000
COUNTS
COUNTS
60000
40000
30000
50000
40000
30000
23000
21862
20000
20000
5919
0
0
10000
3931
42
32
0
0
0
0
0
20015 20016 20017 20018 20019 2001A2001B2001C2001D 2001E
CODE IN HEX
Figure 6. Histogram of 131,072 Conversions of a
DC Input at the Code Transition
AMPLITUDE (dB of Full Scale)
SNR AND S/[N+D] (dB)
fS = 100kSPS
fIN = 11kHz
VREF = 4.096V
SNR = 99.6dB
THD = –116dB
SFDR = 116.2dB
S/(N+D) = 99.5dB
–60
1
0
Figure 9. Histogram of 131,072 Conversions of a
DC Input at the Code Center
0
–40
1053
522
03084-0-009
03084-0-006
–20
0
2001B 2001C 2001D 2001E 2001F 20020 20021 20022 20023
CODE IN HEX
–80
–100
–120
102
16.6
100
16.4
SNR
98
16.2
S/(N+D)
16.0
96
–140
ENOB
–160
–180
0
5
10
15
20
25
30
35
FREQUENCY (kHz)
40
45
94
50
0
10
20
30
FREQUENCY (kHz)
03084-0-012
Figure 7. FFT (11 kHz Tone)
15.8
50
40
03084-0-015
Figure 10. SNR, S/(N+D), and ENOB vs. Frequency
Rev. B | Page 12 of 28
ENOB (Bits)
10000
AD7678
–80
–100
THD, HARMONICS (dB)
THD, HARMONICS (dB)
–90
–100
–110
THD
–120
THIRD
HARMONIC
SECOND
HARMONIC
–130
–110
THD
THIRD
HARMONIC
–120
SECOND
HARMONIC
–130
–140
–150
20
30
FREQUENCY (kHz)
10
0
40
–140
–55
50
Figure 11. THD and Harmonics vs. Frequency
5
25
45
65
85
105
125
03084-0-019
Figure 14. THD and Harmonics vs. Temperature
10000
VREF = 4.096V
1000
103
OPERATING CURRENT (µA)
SNR REFERRED TO FULL SCALE (dB)
–15
TEMPERATURE (°C)
104
102
SNR
101
S/(N+D)
100
100
10
AVDD
1
DVDD
0.1
OVDD
99
0.01
98
–60
–50
–40
–30
–20
–10
INPUT LEVEL (dB)
0.001
0
1
16.0
100
S/(N+D)
ENOB
15.5
99
15.0
98
–15
5
25
45
65
TEMPERATURE (°C)
85
10k
100k
03084-0-020
105
14.5
125
03084-0-018
Figure 13. SNR, S/(N+D), and ENOB vs. Temperature
1000
POWER-DOWN OPERATING CURRENTS (nA)
SNR
–35
100
1k
SAMPLING RATE (SPS)
Figure 15. Operating Current vs. Sampling Rate
16.5
97
–55
10
03084-0-017
Figure 12. SNR and S/(N+D) vs. Input Level
101
SNR, S/[N+D] (dB)
–35
03084-0-016
800
DVDD
600
400
AVDD
200
0
–55
OVDD
–35
–15
5
25
45
65
TEMPERATURE (°C)
85
105
125
03084-0-021
Figure 16. Power-Down Operating Currents vs. Temperature
Rev. B | Page 13 of 28
AD7678
50
50
OVDD = 2.7V @ 85°C
30
40
GAIN ERROR
20
t12 DELAY (ns)
ZERO ERROR, GAIN ERROR (LSB)
40
10
0
ZERO ERROR
–10
30
20
OVDD = 2.7V @ 25°C
OVDD = 5V @ 85°C
–20
–30
OVDD = 5V @ 25°C
10
–40
–50
–55
–35
–15
5
25
45
65
TEMPERATURE (°C)
85
105
0
125
0
50
100
CL (pF)
03083-0-022
Figure 17. Zero Error and Gain Error vs. Temperature
150
200
03084-0-024
Figure 18. Typical Delay vs. Load Capacitance CL
Rev. B | Page 14 of 28
AD7678
CIRCUIT INFORMATION
IN+
MSB
262,144C 131,072C
LSB
4C
2C
C
SW+
SWITCHES
CONTROL
C
BUSY
REF
COMP
CONTROL
LOGIC
OUTPUT
CODE
REFGND
4C
262,144C 131,072C
2C
C
C
LSB
MSB
SW–
IN–
CNVST
03084–0–025
Figure 19. ADC Simplified Schematic
The AD7678 is a very fast, low power, single-supply, precise
18-bit analog-to-digital converter (ADC) using successive
approximation architecture.
CONVERTER OPERATION
The AD7678’s linearity and dynamic range are similar or better
than many Σ-∆ ADCs. With the advantages of its successive
architecture, which ease multiplexing and reduce power with
throughput, it can be advantageous in applications that
normally use Σ-∆ ADCs.
The AD7678 provides the user with an on-chip track/hold,
successive approximation ADC that does not exhibit any
pipeline or latency, making it ideal for multiple multiplexed
channel applications.
The AD7678 can be operated from a single 5 V supply and can
be interfaced to either 5 V or 3 V digital logic. It is housed in a
48-lead LQFP, or a tiny 48-lead LFCSP package that offers
space savings and allows for flexible configurations as either a
serial or parallel interface. The AD7678 is pin-to-pin
compatible with the AD7674, AD7676, and AD7679.
The AD7678 is a successive approximation ADC based on a
charge redistribution DAC. Figure 19 shows the simplified
schematic of the ADC. The capacitive DAC consists of two
identical arrays of 18 binary weighted capacitors, which are
connected to the two comparator inputs.
During the acquisition phase, terminals of the array tied to the
comparator’s input are connected to AGND via SW+ and SW–.
All independent switches are connected to the analog inputs.
Thus, the capacitor arrays are used as sampling capacitors and
acquire the analog signal on IN+ and IN– inputs. When the
acquisition phase is complete and the CNVST input goes low, a
conversion phase is initiated. When the conversion phase
begins, SW+ and SW– are opened first. The two capacitor
arrays are then disconnected from the inputs and connected to
the REFGND input. Therefore, the differential voltage between
the IN+ and IN– inputs captured at the end of the acquisition
phase is applied to the comparator inputs, causing the
comparator to become unbalanced. By switching each element
of the capacitor array between REFGND and REF, the
comparator input varies by binary weighted voltage steps
(VREF/2, VREF/4...VREF/262144). The control logic toggles these
switches, starting with the MSB first, to bring the comparator
back into a balanced condition. After completing this process,
the control logic generates the ADC output code and brings the
BUSY output low.
Rev. B | Page 15 of 28
AD7678
Transfer Functions
Table 8. Output Codes and Ideal Input Voltages
ADC CODE (Straight Binary)
Except in 18-bit interface mode, the AD7678 offers straight
binary and twos complement output coding when using OB/2C
. See Figure 20 and Table 8 for the ideal transfer characteristic.
Description
FSR –1 LSB
FSR – 2 LSB
Midscale +
1 LSB
Midscale
Midscale –
1 LSB
–FSR + 1 LSB
–FSR
111...111
111...110
111...101
Analog Input
VREF = 4.096 V
4.095962 V
4.095924 V
31.25 µV
Straight
Binary
(Hex)
3FFFF 1
3FFFE
20001
Twos
Complement
(Hex)
1FFFF5
1FFFE
00001
0V
–31.25 µV
20000
1FFFF
00000
3FFFF
-4.095962 V
-4.096 V
00001
00000 2
20001
200006
000...010
000...001
000...000
–FS
–FS + 1 LSB
1
+FS – 1 LSB
–FS + 0.5 LSB
2
+FS – 1.5 LSB
ANALOG INPUT
This is also the code for overrange analog input (VIN+ – VIN–
above VREF – VREFGND).
This is also the code for underrange analog input (VIN+ – VIN–
below –VREF + VREFGND).
03084-0-026
Figure 20. ADC Ideal Transfer Function
DVDD
ANALOG
SUPPLY
(5V)
20Ω
DIGITAL SUPPLY
(3.3V OR 5V)
NOTE 5
+
10µF
ADR421
+
100nF
AVDD
AGND
10µ F
100nF
DGND
DVDD
100nF
OVDD
1MΩ
50kΩ
NOTE 1
100nF
SDOUT
NOTE 3
CREF
REF
BUSY
10µF
NOTE 2
µC/µP/DSP
REFGND
CNVST
50Ω
NOTE 4
–
U1
+
AD8021
IN+
AD7678
CC
MODE1
MODE0
OB/2C
PDBUF
50Ω
NOTE 4
ANALOG INPUT–
SERIAL PORT
SCLK
100nF
ANALOG INPUT+
10µ F
OGND
REFBUFIN
2.5V REF
+
CLOCK
CS
RD
–
U2
+
AD8021
DVDD
IN–
RESET
PD
CC
NOTES
1. SEE VOLTAGE REFERENCE SECTION.
2. CREF is 10µF CERAMIC CAPACITOR OR LOW ESR TANTALUM. CERAMIC SIZE
1206 PANASONIC ECJ-3xB0J106 IS RECOMMENDED. SEE VOLTAGE REFERENCE SECTION.
3. OPTIONAL CIRCUITRY FOR HARDWARE GAIN CALIBRATION.
4.THE AD8021 IS RECOMMENDED. SEE DRIVER AMPLIFIER CHOICE SECTION.
5. OPTION, SEE POWER SUPPLY SECTION.
Figure 21. Typical Connection Diagram (Internal Reference Buffer, Serial Interface)
Rev. B | Page 16 of 28
03084-0-027
AD7678
TYPICAL CONNECTION DIAGRAM
Figure 21 shows a typical connection diagram for the AD7678.
Different circuitry shown on this diagram is optional and is
discussed later in this data sheet.
Analog Inputs
Figure 22 shows a simplified analog input section of the
AD7678. The diodes shown in Figure 22 provide ESD protection for the inputs. Care must be taken to ensure that the
analog input signal never exceeds the absolute ratings on these
inputs. This will cause these diodes to become forward-biased
and start conducting current. These diodes can handle a
forward-biased current of 120 mA max. This condition could
eventually occur when the input buffer’s U1 or U2 supplies are
different from AVDD. In such a case, an input buffer with a
short-circuit current limitation can be used to protect the part.
AVDD
During the acquisition phase for ac signals, the AD7678 behaves
like a 1-pole RC filter consisting of the equivalent resistance,
R+, R–, and CS. Resistors R+ and R– are typically 3 kΩ and are
lumped components made up of a serial resistor and the on
resistance of the switches. CS is typically 60 pF and mainly
consists of the ADC sampling capacitor. This 1-pole filter with
a –3 dB cutoff frequency of 900 kHz typ reduces any
undesirable aliasing effect and limits the noise coming from the
inputs.
Because the input impedance of the AD7678 is very high, the
part can be driven directly by a low impedance source without
gain error.
Driver Amplifier Choice
Although the AD7678 is easy to drive, the driver amplifier
needs to meet the following requirements:
•
The driver amplifier and the AD7678 analog input circuit
have to be able to settle for a full-scale step of the capacitor
array at an 18-bit level (0.0004%). In the amplifier’s data
sheet, settling at 0.1% or 0.01% is more commonly
specified. This could differ significantly from the settling
time at an 18-bit level and, therefore, should be verified
prior to driver selection. The tiny op amp AD8021, which
combines ultralow noise and high gain-bandwidth, meets
this settling time requirement.
•
The noise generated by the driver amplifier needs to be
kept as low as possible in order to preserve the SNR and
transition noise performance of the AD7678. The noise
coming from the driver is filtered by the AD7678 analog
input circuit 1-pole low-pass filter made by R+, R–, and CS.
R+ = 3kΩ
IN+
CS
CS
IN–
R– = 3kΩ
AGND
03084-0-028
Figure 22. Simplified Analog Input
This analog input structure is a true differential structure. By
using these differential inputs, signals common to both inputs
are rejected as shown in Figure 23, which represents typical
CMRR over frequency.
The SNR degradation due to the amplifier is
SNRLOSS = 20 log
80
75
CMRR (dB)
625 +π f –3dB (Ne N ) 2
where:
f–3dB is the –3 dB input bandwidth in MHz of the AD7678
(0.9 MHz).
N is the noise factor of the amplifiers (1 if in buffer
configuration).
eN is the equivalent input noise voltage of each op amp in
nV/√Hz.
70
65
60
55
50
25
1
10
100
FREQUECY (kHz)
1000
For instance, for a driver with an equivalent input noise of
6 nV/√Hz (e.g., AD8610) configured as a buffer, thus with
a noise gain of +1, the SNR degrades by only 0.65 dB.
10000
03084-0-029
Figure 23. Analog Input CMRR vs. Frequency
•
Rev. B | Page 17 of 28
The driver needs to have a THD performance suitable to
that of the AD7678.
AD7678
The AD8021 meets these requirements and is usually appropriate for almost all applications. The AD8021 needs a 10 pF
external compensation capacitor, which should have good
linearity as an NPO ceramic or mica type.
The AD8022 could be used if a dual version is needed and gain
of 1 is present. The AD829 is an alternative in applications
where high frequency (above 100 kHz) performance is not
required. In gain of 1 applications, it requires an 82 pF
compensation capacitor. The AD8610 is another option when
low bias current is needed in low frequency applications.
Single-to-Differential Driver
For applications using unipolar analog signals, a single-endedto-differential driver will allow for a differential input into the
part. The schematic is shown in Figure 24. When provided an
input signal of 0 to VREF, this configuration will produce a
differential ±VREF with midscale at VREF/2.
If the application can tolerate more noise, the AD8138
differential driver can be used.
ANALOG INPUT
(UNIPOLAR
0V TO 4.096V)
U1
AD8021
10pF
590Ω
IN+
590Ω
AD7678
IN– REF
U2
1.82kΩ
AD8021
8.25kΩ
100nF
10pF
To use the internal reference buffer, PDBUF should be LOW. A
2.5 V reference voltage applied on the REFBUFIN input will
result in a 4.096 V reference on the REF pin.
In both cases, the voltage reference input REF has a dynamic
input impedance and therefore requires an efficient decoupling
between REF and REFGND inputs. The decoupling consists of
a low ESR 47 µF tantalum capacitor connected to the REF and
REFGND inputs with minimum parasitic inductance.
Care should also be taken with the reference temperature
coefficient of the voltage reference, which directly affects the
full-scale accuracy if this parameter matters. For instance, a
±4 ppm/°C temperature coefficient of the reference changes the
full scale by ±1 LSB/°C.
Power Supply
The AD7678 uses three sets of power supply pins: an analog 5
V supply (AVDD), a digital 5 V core supply (DVDD), and a
digital output interface supply (OVDD). The OVDD supply
defines the output logic level and allows direct interface with
any logic working between 2.7 V and DVDD + 0.3 V. To
reduce the number of supplies needed, the digital core (DVDD)
can be supplied through a simple RC filter from the analog
supply, as shown in Figure 21. The AD7678 is independent of
power supply sequencing once OVDD does not exceed DVDD
by more than 0.3 V, and is therefore free from supply voltage
induced latch-up. Additionally, it is very insensitive to power
supply variations over a wide frequency range, as shown in
Figure 25.
REFBUFIN
10µF
65
2.5V
03084-0-030
60
PSRR (dB)
Figure 24. Single-Ended-to-Differential Driver Circuit
(Internal Reference Buffer Used)
Voltage Reference
The AD7678 allows the use of an external voltage reference
with or without the internal reference buffer.
Using the internal reference buffer is recommended when
sharing a common reference voltage between multiple ADCs is
desired.
However, the advantages of using the external reference voltage
directly are
•
The SNR and dynamic range improvement (about 1.7 dB)
resulting from the use of a reference voltage very close to
the supply (5 V) instead of a typical 4.096 V reference
when the internal buffer is used.
•
The power saving when the internal reference buffer is
powered down (PDBUF HIGH).
Rev. B | Page 18 of 28
55
50
45
40
1
10
100
FREQUECY (kHz)
1000
Figure 25. PSRR vs. Frequency
10000
03084-0-031
AD7678
POWER DISSIPATION VERSUS THROUGHPUT
t2
The AD7678 automatically reduces its power consumption at
the end of each conversion phase. During the acquisition phase,
the operating currents are very low, which allows for a significant power savings when the conversion rate is reduced, as
shown in Figure 26. This feature makes the AD7678 ideal for
very low power battery applications.
It should be noted that the digital interface remains active even
during the acquisition phase. To reduce the operating digital
supply currents even further, the digital inputs need to be
driven close to the power rails (DVDD and DGND), and
OVDD should not exceed DVDD by more than 0.3 V.
100000
t1
CNVST
BUSY
t4
t3
t6
t5
MODE
ACQUIRE
CONVERT
ACQUIRE
t7
t8
CONVERT
03084-0-033
Figure 27. Basic Conversion Timing
Although CNVST is a digital signal, it should be designed with
special care with fast, clean edges and levels with minimum
overshoot and undershoot or ringing.
POWER DISSIPATION (mW)
10000
For other applications, conversions can be automatically
initiated. If CNVST is held low when BUSY is low, the AD7678
controls the acquisition phase and then automatically initiates a
new conversion. By keeping CNVST low, the AD7678 keeps the
conversion process running by itself. It should be noted that the
analog input has to be settled when BUSY goes low. Also, at
power-up, CNVST should be brought low once to initiate the
conversion process. In this mode, the AD7678 could sometimes
run slightly faster than the guaranteed limits of 100 kSPS.
1000
100
10
1
PDBUF HIGH
0.1
1
10
100
1k
SAMPLING RATE (SPS)
10k
100k
03084-0-032
t9
Figure 26. Power Dissipation vs. Sample Rate
RESET
CONVERSION CONTROL
Figure 27 shows the detailed timing diagrams of the conversion
process. The AD7678 is controlled by the CNVST signal, which
initiates conversion. Once initiated, it cannot be restarted or
aborted, even by the power-down input PD, until the
conversion is complete. The CNVST signal operates
independently of the CS and RD signals.
BUSY
DATA
BUS
t8
CNVST
03084-0-034
Figure 28. RESET Timing
Rev. B | Page 19 of 28
AD7678
DIGITAL INTERFACE
The AD7678 has a versatile digital interface; it can be interfaced
with the host system by using either a serial or parallel
interface. The serial interface is multiplexed on the parallel data
bus. The AD7678 digital interface also accommodates both 3 V
and 5 V logic by simply connecting the AD7678’s OVDD
supply pin to the host system interface digital supply. Finally,
by using the OB/2C input pin in any mode except 18-bit
interface mode, both twos complement and straight binary
coding can be used.
The two signals, CS and RD, control the interface. When at
least one of these signals is high, the interface outputs are in
high impedance. Usually, CS allows the selection of each
AD7678 in multicircuit applications, and is held low in a single
AD7678 design. RD is generally used to enable the conversion
result on the data bus.
CS
RD
BUSY
DATA
BUS
CURRENT
CONVERSION
t12
03084-0-036
Figure 30. Slave Parallel Data Timing for Reading (Read after Convert)
CS = 0
t1
CNVST,
RD
BUSY
t4
t3
CS = RD = 0
t1
PREVIOUS
CONVERSION
DATA
BUS
CNVST
t12
t10
t13
03084-0-037
t4
BUSY
t3
DATA
BUS
t13
Figure 31. Slave Parallel Data Timing for Reading (Read during Convert)
t11
PREVIOUS CONVERSION DATA
NEW DATA
CS
03084-0-035
Figure 29. Master Parallel Data Timing for Reading (Continuous Read)
RD
PARALLEL INTERFACE
A0, A1
The AD7678 is configured to use the parallel interface with an
18-bit, a 16-bit, or an 8-bit bus width, according to Table 7. The
data can be read either after each conversion, which is during
the next acquisition phase, or during the following conversion,
as shown in Figure 30 and Figure 31, respectively. When the
data is read during the conversion, however, it is recommended
that it is read only during the first half of the conversion phase.
This avoids any potential feedthrough between voltage
transients on the digital interface and the most critical analog
conversion circuitry. Refer to Table 7 for a detailed description
of the different options available.
PINS D[15:8]
HI-Z
HIGH BYTE
t12
PINS D[7:0]
HI-Z
LOW BYTE
LOW BYTE
t12
HIGH BYTE
HI-Z
t13
HI-Z
03084-0-038
Figure 32. 8-Bit and 16-Bit Parallel Interface
SERIAL INTERFACE
The AD7678 is configured to use the serial interface when
MODE0 and MODE1 are held high. The AD7678 outputs 18
bits of data, MSB first, on the SDOUT pin. This data is
synchronized with the 18 clock pulses provided on the SCLK
pin. The output data is valid on both the rising and falling edge
of the data clock.
Rev. B | Page 20 of 28
AD7678
MASTER SERIAL INTERFACE
In Read during Conversion mode, the serial clock and data
toggle at appropriate instants, minimizing potential
feedthrough between digital activity and critical conversion
decisions.
Internal Clock
The AD7678 is configured to generate and provide the serial
data clock SCLK when the EXT/INT pin is held low. The
AD7678 also generates a SYNC signal to indicate to the host
when the serial data is valid. The serial clock SCLK and the
SYNC signal can be inverted if desired. Depending on the
RDC/SDIN input, the data can be read after each conversion or
during the following conversion. Figure 33 and Figure 34 show
the detailed timing diagrams of these two modes.
In Read after Conversion mode, it should be noted that unlike
in other modes, the BUSY signal returns low after the 18 data
bits are pulsed out and not at the end of the conversion phase,
which results in a longer BUSY width.
To accommodate slow digital hosts, the serial clock can be
slowed down by using DIVSCLK.
Usually, because the AD7678 is used with a fast throughput, the
mode master read during conversion is the most recommended
serial mode.
RDC/SDIN = 0
EXT/INT = 0
CS, RD
INVSCLK = INVSYNC = 0
t3
CNVST
t28
BUSY
t30
t29
t25
SYNC
t18
t19
t14
t24
t21
t20
t26
SCLK
1
2
D17
D16
3
16
17
D2
D1
18
t15
t27
X
SDOUT
t16
t22
D0
t23
03084-0-039
Figure 33. Master Serial Data Timing for Reading (Read after Convert)
Rev. B | Page 21 of 28
AD7678
RDC/SDIN = 1
EXT/INT = 0
CS, RD
INVSCLK = INVSYNC = 0
t1
CNVST
t3
BUSY
t17
t25
SYNC
t14
t19
t20 t21
t15
SCLK
1
t24
2
3
16
17
t18
X
SDOUT
t16
t27
D17
t22
t26
18
D16
D2
D1
D0
t23
03084-0-040
Figure 34. Master Serial Data Timing for Reading (Read Previous Conversion during Convert)
SLAVE SERIAL INTERFACE
External Clock
The AD7678 is configured to accept an externally supplied
serial data clock on the SCLK pin when the EXT/INT pin is
held high. In this mode, several methods can be used to read
the data. The external serial clock is gated by CS. When CS and
RD are both low, the data can be read after each conversion or
during the following conversion. The external clock can be
either a continuous or a discontinuous clock. A discontinuous
clock can be either normally high or normally low when
inactive. Figure 35 and Figure 36 show the detailed timing
diagrams of these methods.
While the AD7678 is performing a bit decision, it is important
that voltage transients not occur on digital input/output pins or
degradation of the conversion result could occur. This is
particularly important during the second half of the conversion
phase because the AD7678 provides error correction circuitry
that can correct for an improper bit decision made during the
first half of the conversion phase. For this reason, it is recommended that when an external clock is being provided, it is a
discontinuous clock that only toggles when BUSY is low or,
more importantly, that it does not transition during the latter
half of BUSY high.
External Discontinuous Clock Data Read after
Conversion
This mode is the most recommended of the serial slave modes.
Figure 35 shows the detailed timing diagrams of this method.
After a conversion is complete, indicated by BUSY returning
low, the result of this conversion can be read while both CS and
RD are low. Data is shifted out MSB first with 18 clock pulses,
and is valid on both the rising and falling edge of the clock.
Among the advantages of this method, the conversion performance is not degraded because there are no voltage transients
on the digital interface during the conversion process. Also,
data can be read at speeds up to 40 MHz, accommodating both
slow digital host interface and the fastest serial reading.
Finally, in this mode only, the AD7678 provides a daisy-chain
feature using the RDC/SDIN input pin to cascade multiple
converters together. This feature is useful for reducing
component count and wiring connections when desired (for
instance, in isolated multiconverter applications).
An example of the concatenation of two devices is shown in
Figure 37. Simultaneous sampling is possible by using a
common CNVST signal. It should be noted that the RDC/SDIN
input is latched on the edge of SCLK opposite the one used to
shift out data on SDOUT. Thus, the MSB of the upstream
converter follows the LSB of the downstream converter on the
next SCLK cycle.
Rev. B | Page 22 of 28
AD7678
INVSCLK = 0
EXT/INT = 1
RD = 0
CS
BUSY
t36
SCLK
t35
t37
1
2
t31
3
16
17
18
19
20
t32
SDOUT
X
D17
t16
D16
D15
D1
D0
X17
X16
X16
X15
X1
X0
Y17
Y16
t34
SDIN
X17
t33
03084-0-041
Figure 35. Slave Serial Data Timing for Reading (Read after Convert)
EXT/INT = 1
INVSCLK = 0
RD = 0
CS
CNVST
BUSY
t3
t35
t36
SCLK
t37
1
2
t31
SDOUT
3
16
17
18
t32
X
D17
D16
D15
D1
D0
t16
03084-0-042
Figure 36. Slave Serial Data Timing for Reading (Read Previous Conversion during Convert)
Rev. B | Page 23 of 28
AD7678
BUSY
OUT
BUSY
BUSY
AD7678
AD7678
#2 (UPSTREAM)
#1 (DOWNSTREAM)
RDC/SDIN
SDOUT
CNVST
RDC/SDIN
MICROPROCESSOR INTERFACING
The AD7678 is ideally suited for traditional dc measurement
applications supporting a microprocessor, and for ac signal
processing applications interfacing to a digital signal processor.
The AD7678 is designed to interface either with a parallel 8-bit
or 16-bit wide interface, or with a general-purpose serial port or
I/O ports on a microcontroller. A variety of external buffers can
be used with the AD7678 to prevent digital noise from coupling
into the ADC. The following section illustrates the use of the
AD7678 with an SPI equipped DSP, the ADSP-219x.
DATA
OUT
SDOUT
CNVST
CS
CS
SCLK
SCLK
SCLK IN
CS IN
CNVST IN
03084-0-043
SPI Interface (ADSP-219x)
Figure 37. Two AD7678s in a Daisy-Chain Configuration
External Clock Data Read during Conversion
Figure 36 shows the detailed timing diagrams of this method.
During a conversion, while both CS and RD are low, the result
of the previous conversion can be read. The data is shifted out
MSB first with 18 clock pulses, and is valid on both the rising
and falling edge of the clock. The 18 bits have to be read before
the current conversion is complete. If that is not done,
RDERROR is pulsed high and can be used to interrupt the host
interface to prevent incomplete data reading. There is no daisychain feature in this mode, and the RDC/SDIN input should
always be tied either high or low.
To reduce performance degradation due to digital activity, a
fast discontinuous clock is recommended to ensure that all bits
are read during the first half of the conversion phase. It is also
possible to begin to read the data after conversion and continue
to read the last bits even after a new conversion has been
initiated.
Figure 38 shows an interface diagram between the AD7678 and
the SPI equipped ADSP-219x. To accommodate the slower
speed of the DSP, the AD7678 acts as a slave device, and data
must be read after conversion. This mode also allows the daisychain feature. The convert command could be initiated in
response to an internal timer interrupt. The 18-bit output data
are read with 3-byte SPI access. The reading process could be
initiated in response to the end-of-conversion signal (BUSY
going low) using an interrupt line of the DSP. The serial
interface (SPI) on the ADSP-219x is configured for master
mode (MSTR) = 1, Clock Polarity bit (CPOL) = 0, Clock Phase
bit (CPHA) = 1, and SPI interrupt enable (TIMOD) = 00, by
writing to the SPI control register (SPICLTx). It should be
noted that to meet all timing requirements, the SPI clock
should be limited to 17 Mbits/s, which allow it to read an ADC
result in about 1.1 µs.
DVDD
ADSP-219x*
AD7678*
SER/PAR
EXT/INT
BUSY
CS
RD
INVSCLK
SDOUT
SCLK
CNVST
PFx
SPIxSEL (PFx)
MISOx
SCKx
PFx or TFSx
* ADDITIONAL PINS OMITTED FOR CLARITY
03084-0-044
Figure 38. Interfacing the AD7678 to an SPI Interface
Rev. B | Page 24 of 28
AD7678
APPLICATION HINTS
LAYOUT
The AD7678 has very good immunity to noise on the power
supplies. However, care should still be taken with regard to
grounding layout.
The printed circuit board that houses the AD7678 should be
designed so that the analog and digital sections are separated
and confined to certain areas of the board. This facilitates the
use of ground planes that can be easily separated. Digital and
analog ground planes should be joined in only one place,
preferably underneath the AD7678, or at least as close to the
AD7678 as possible. If the AD7678 is in a system where
multiple devices require analog-to-digital ground connections,
the connection should still be made at one point only, a star
ground point that should be established as close to the AD7678
as possible.
The user should avoid running digital lines under the device,
because these will couple noise onto the die. The analog ground
plane should be allowed to run under the AD7678 to avoid
noise coupling. Fast switching signals like CNVST or clocks
should be shielded with digital ground to avoid radiating noise
to other sections of the board, and should never run near
analog signal paths. Crossover of digital and analog signals
should be avoided. Traces on different but close layers of the
board should run at right angles to each other. This will reduce
the effect of feedthrough through the board. The power supply
lines to the AD7678 should use as large a trace as possible to
provide low impedance paths and reduce the effect of glitches
on the power supply lines. Good decoupling is also important
to lower the supply’s impedance presented to the AD7678 and
to reduce the magnitude of the supply spikes. Decoupling
ceramic capacitors, typically 100 nF, should be placed close to
and ideally right up against each power supply pin (AVDD,
DVDD, and OVDD) and their corresponding ground pins.
Additionally, low ESR 10 µF capacitors should be located near
the ADC to further reduce low frequency ripple.
The DVDD supply of the AD7678 can be a separate supply or
can come from the analog supply, AVDD, or the digital
interface supply, OVDD. When the system digital supply is
noisy or when fast switching digital signals are present, and if
no separate supply is available, the user should connect the
DVDD digital supply to the analog supply AVDD through an
RC filter, (see Figure 21), and connect the system supply to the
interface digital supply OVDD and the remaining digital
circuitry. When DVDD is powered from the system supply, it is
useful to insert a bead to further reduce high frequency spikes.
The AD7678 has four different ground pins: REFGND, AGND,
DGND, and OGND. REFGND senses the reference voltage and
should be a low impedance return to the reference because it
carries pulsed currents. AGND is the ground to which most
internal ADC analog signals are referenced. This ground must
be connected with the least resistance to the analog ground
plane. DGND must be tied to the analog or digital ground
plane depending on the configuration. OGND is connected to
the digital system ground.
The layout of the decoupling of the reference voltage is
important. The decoupling capacitor should be close to the
ADC and should be connected with short and large traces to
minimize parasitic inductances.
EVALUATING THE AD7678’S PERFORMANCE
The evaluation board for the AD7678 allows a quick means to
measure both dc (histograms and time domain) and ac (time
and frequency domain) performances of the converter. The
EVAL-AD7678CBZ is an evaluation board package that includes
a fully assembled and tested evaluation board, documentation,
and software. The accompanying software requires the use of a
capture board that must be ordered seperately from the evaluation board (see the Ordering Guide for information). The
evaluation board can also be used in a standalone configuration
and does not use the software when in this mode. Refer to the
EVAL-AD76XXEDZ and EVAL-AD76XXCBZ data sheets
available from www.analog.com for evaluation board details.
Two types of data capture boards can be used with the EVALAD7678CBZ:
•
•
USB based (EVAL-CED1Z recommended)
Parallel port based (EVAL-CONTROL BRD3Z not
recommended because many newer PCs do not include
parallel ports any longer)
The recommended board layout for the AD7678 is outlined in
the evaluation board data sheet.
Rev. B | Page 25 of 28
AD7678
OUTLINE DIMENSIONS
0.75
0.60
0.45
9.20
9.00 SQ
8.80
1.60
MAX
37
48
36
1
PIN 1
7.20
7.00 SQ
6.80
TOP VIEW
1.45
1.40
1.35
0.15
0.05
0.20
0.09
7°
3.5°
0°
0.08
COPLANARITY
SEATING
PLANE
(PINS DOWN)
25
12
13
24
0.27
0.22
0.17
VIEW A
0.50
BSC
LEAD PITCH
051706-A
VIEW A
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-BBC
Figure 39. 48-Lead Low Profile Quad Flat Package [LQFP]
(ST-48)
Dimensions shown in millimeters
PIN 1
INDICATOR
AREA
7.10
7.00 SQ
6.90
DETAIL A
(JEDEC 95)
0.30
0.23
0.18
37
36
48
1
0.50
BSC
P IN 1
IN D IC ATO R AR E A OP T IO N S
(SEE DETAIL A)
5.20
5.10 SQ
5.00
EXPOSED
PAD
12
0.80
0.75
0.70
END VIEW
PKG-004509
SEATING
PLANE
0.45
0.40
0.35
24
13
BOTTOM VIEW
0.20 MIN
5.50 REF
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.203 REF
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WKKD-4
10-10-2018-C
TOP VIEW
Figure 40. 48-Lead Lead Frame Chip Scale Package [LFCSP]
7 mm × 7 mm Body and 0.75 mm Package Height
(CP-48-4)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD7678ASTZ 1
AD7678ASTZRL1
AD7678ACPZ1
AD7678ACPZRL1
EVAL-AD7678CBZ 2
EVAL-CONTROL BRD2Z1, 3
EVAL-CONTROL BRD3Z1, 3
EVAL-CED1Z1, 3
Temperature Range
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Package Description
48-Lead Low Profile Quad Flat Package [LQFP]
48-Lead Low Profile Quad Flat Package [LQFP]
48-Lead Lead Frame Chip Scale Package [LFCSP]
48-Lead Lead Frame Chip Scale Package [LFCSP]
Evaluation Board
Package Option
ST-48
ST-48
CP-48-4
CP-48-4
Parallel Port Capture Board, 32k RAM
Parallel Port Capture Board, 128k RAM
USB Data Capture Board
Z = RoHS Compliant Part.
This board can be used as a standalone evaluation board or in conjunction with the capture board for evaluation/demonstration purposes.
These capture board allow the PC to control and communicate with all Analog Devices evaluation boards ending in ED for EVAL-CED1Z and CB for EVAL-CONTROL
BRDxZ (x = 2, 3).
1
2
3
Rev. B | Page 26 of 28
AD7678
NOTES
Rev. B | Page 27 of 28
AD7678
NOTES
©2003–2020 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective companies.
D03084-8/20(B)
Rev. B | Page 28 of 28
工商网监
湘ICP备2023018690号
