AD9549

Preliminary Technical Data FEATURES Flexible Reference Inputs Input frequencies 8 kHz to 750 MHz Two reference inputs Loss of Reference indicators Auto and Manual Holdover modes Auto and Manual Switchover modes Smooth A to B phase transition on outputs Excellent stability in holdover mode Programmable 16+1-bit Input Divider, R Differential HSTL Clock Output Output frequencies to 750 MHz Low Jitter clock doubler for frequencies > 400 MHz Single-ended CMOS output; frequencies < 50MHz Programmable Digital Loop Filter (< 1 Hz to ~100 kHz) High Speed Digitally Controlled Oscillator (DCO) core DDS with integrated 14 bit DAC Excellent Dynamic Performance Programmable 16+1-bit Feedback Divider, S Software controlled power-down 64-lead LFCSP package Dual Input Network Clock Generator/Synchronizer AD9549 APPLICATIONS Network Synchronization Reference Clock Jitter Cleanup SONET/SDH Clocks up to OC-192, Including FEC Stratum 3/3E Reference Clocks Wireless Base Stations, Controllers Cable Infrastructure Data Communications GENERAL DESCRIPTION The AD9549 provides synchronization for many systems including synchronous optical networks (SONET/SDH). The AD9549 generates an output clock, synchronized to one of two external input references. The external references may contain significant time jitter, also specified as phase noise. Using a digitally controlled loop and holdover circuitry, the AD9549 continues to generate a clean (low jitter), valid output clock during a ‘loss of reference’ condition, even when both references have failed. The AD9549 operates over an industrial temperature range, spanning -40°C to +85°C. Figure 1: Basic Block Diagram Rev. PrA Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2007 Analog Devices, Inc. All rights reserved. AD9549 SAMPLE APPLICATION CIRCUIT Preliminary Technical Data Figure 2: AD9549 + AD9514 Precision Clock Distribution Circuit Features: Input Frequencies Down to 8 kHz. Output Frequencies Up to 400 MHz. Programmable Loop Bandwidth Down to < 1 Hz Automatic Redundant Clock Switchover with User Selectable Rate of Phase Adjustment. Automatic Stratum 2/3/3E Clock Holdover, Depending on Configuration. Phase Noise (Fc=122.3 MHz & 100 Hz loop BW): 100 Hz offset: -107 dBc/Hz. 1 KHz offset: -142 dBc/Hz. 100 kHz offset: -157 dBc/Hz. Two Zero-delay Outputs with Programmable Post-Divider and Synchronization. Two Additional Outputs (non-zero delay) on AD9549. Programmable Skew Adjustment on One AD9514 Output. Rev. PrA | Page 2 of 78 Preliminary Technical Data TABLE OF CONTENTS Features...............................................................................................1 Applications .......................................................................................1 General Description..........................................................................1 Sample Application Circuit..............................................................2 DC Specifications ..............................................................................5 AC Specifications ..............................................................................7 Typical Performance Characteristics ............................................13 Absolute Maximum Ratings ..........................................................17 ESD Caution ................................................................................17 Pin Configuration and Function Descriptions ...........................18 Input / Output Termination Recommendations.........................21 Theory of Operation .......................................................................22 Overview ......................................................................................22 PLL Core (DPLLC) .....................................................................23 Feedforward Divider (Divide-by-R).....................................23 Feedback Divider (Divide-by-S) ...........................................23 Forward and Reverse FEC Clock Scaling ............................24 Phase Detector.........................................................................24 Digital Loop Filter...................................................................24 Direct Digital Synthesizer ......................................................26 DAC Output.............................................................................27 Phase Detector.............................................................................27 Coarse Phase Detector ...........................................................27 Fine Phase Detector................................................................27 Phase Detector Gain Matching .............................................28 Phase Detector Pin Connections ..........................................28 Digital Loop Filter Coefficients ................................................28 Closed Loop Phase Offset..........................................................30 Lock Detection ............................................................................31 Rev. PrA | Page 3 of 78 AD9549 Phase Lock Detection.............................................................31 Frequency Lock Detection ....................................................32 Reference Monitors ....................................................................33 Loss of Reference ....................................................................33 Reference Frequency Monitor...............................................33 Reference Switchover .................................................................34 Use of Line Card Mode to Eliminate Runt Pulses..............35 Holdover ......................................................................................36 Holdover Control....................................................................36 Holdover & Reference Switchover State Machine..............36 Reference Recovery Timers...................................................37 Holdover Operation ...............................................................38 Holdover Sampler and Averager...........................................39 Output Frequency Range Control ............................................39 Reconstruction Filter..................................................................39 Use of Narrowband Filter for High Performance...............40 FDBK Inputs................................................................................41 Reference Inputs .........................................................................41 Reference Clock Receiver ......................................................41 SysClk Inputs...............................................................................42 Functional Description ..........................................................42 Bipolar Edge Detector ............................................................42 SysClk PLL Multiplier ............................................................42 External Loop Filter (SysClk PLL) .......................................43 Detail of SysClk Differential Inputs .....................................43 Harmonic Spur Reduction.........................................................45 Output Clock Drivers & 2x frequency Multiplier ..................46 Primary 1.8V Differential HSTL Driver..............................46 2x Frequency Multiplier.........................................................46 AD9549 Single-Ended CMOS Output................................................ 46 Frequency Slew Limiter............................................................. 46 Frequency Estimator.................................................................. 47 Status and Warnings .................................................................. 48 Status Pins ............................................................................... 48 Reference Monitor Status ...................................................... 49 Default DDS Output Frequency on Power-Up .................. 49 Interrupt Request (IRQ)........................................................ 49 Power-On Reset.......................................................................... 51 AD9549 Power Up and Programming Sequence................... 51 Power Management........................................................................ 52 3.3V Supplies............................................................................... 52 1.8V Supplies............................................................................... 52 Serial Control Port.......................................................................... 53 Serial Control Port Pin Descriptions....................................... 53 Operation of Serial Control Port.............................................. 53 Framing a Communication Cycle with CSB ...................... 53 Communication Cycle—Instruction Plus Data ................. 53 Write......................................................................................... 53 Preliminary Technical Data Read ......................................................................................... 54 The Instruction Word (16 Bits)................................................ 54 MSB/LSB First Transfers ........................................................... 54 I/O Register Map ............................................................................ 58 1 Types of Registers:................................................................ 65 I/O Register Description ............................................................... 66 Serial Port Configuration (0000 – 0005)............................. 66 Power Down and Reset ......................................................... 66 System Clock........................................................................... 67 Digital PLL Control and Dividers........................................ 68 Digital PLL Loop Filter.......................................................... 69 Free-Run (Single-Tone) Mode.............................................. 70 Reference Selector / Holdover .............................................. 70 Doubler and Output Drivers ................................................ 71 Monitor.................................................................................... 72 Calibration (User Accessible Trim) ..................................... 75 Harmonic Spur Reduction.................................................... 77 Outline Dimensions ....................................................................... 78 Ordering Guide............................................................................... 78 Rev. PrA | Page 4 of 78 Preliminary Technical Data DC SPECIFICATIONS Unless otherwise noted, AVDD=1.8±5%, AVDD3=3.3±5%, DVDD=1.8±5%, DVDD_I/O=3.3±5%. Table 1. Parameter SUPPLY VOLTAGE DVDD_I/O (pin 1) DVDD (pin 3, 5, 7) AVDD3 (pin 14, 46, 47, 49) AVDD3 (pin 37) AVDD (pin 11,19, 23-26,29,30,36,42,44,45,53) SUPPLY CURRENT I-AVDD3 (pin 14) I-AVDD3 (pin 37) I-AVDD3 (pin 46, 47, 49) I-AVDD (pin 36) I-AVDD (pin 42) I-AVDD (pin 11) I-AVDD (pin 19, 23-26, 29, 30, 44, 45) I-AVDD (pin 53) I-DVDD (pin 3, 5, 7) I-DVDD_I/O (pin 1) LOGIC INPUTS (Except Pin 32) Input High Voltage (VIH) Input Low Voltage (VIL) Input Current (IINH, IINL) Maximum Input Capacitance (CIN) CLKMODESEL (Pin 32) LOGIC INPUT Input High Voltage (VIH) Input Low Voltage (VIL) Input Current (IINH, IINL) Maximum Input Capacitance (CIN) LOGIC OUTPUTS Output High Voltage (VOH) Output Low Voltage (VOL) REFERENCE INPUTS Input Capacitance Input Resistance Common Mode Input Voltage1 Differential Input Voltage Swing1 Input Voltage High (VIH) Input Voltage Low (VIL) Input Current Internal Bias Voltage FDBK INPUT Input Capacitance Input Resistance Common Mode Input Voltage2 Differential Input Voltage Swing2 Min 3.135 1.71 3.135 1.71 1.71 Typ 3.30 1.80 3.30 3.30 1.80 6 25 8 10 10 170 35 200 3 2.0 ±30 3 1.4 ±30 3 2.7 0.4 3 16 0.4 ±100 0.8 ±100 Max 3.465 1.89 3.465 3.465 1.89 TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD Unit V V V V V mA mA mA mA mA mA mA mA mA mA V V µA pF V V µA pF V V pF KΩ V mV V V mA mV AD9549 Test Conditions/Comments (with respect to DVSS) (with respect to DVSS) (with respect to AVSS) (with respect to AVSS) (with respect to AVSS) REFA, REFB Buffers CMOS Output Clock Driver at 3.3V DAC output current source HSTL Output Clock Driver FDBK SYSCLK aggregate analog supply DAC Power Supply Digital Core Digital I/O (varies dynamically) Pins 56-61, 64, 9, 10, 54, 55, 63 At Vin=0V and Vin=DVDD_I/O Pin 32 only. At Vin=0V and Vin=DVDD_I/O Pin 62, & bi-dir. pins 9, 10, 54, 55, 63 IOH = 1 mA w/ VOH =DVDD_I/O-0.4V IOL = 1mA w/ VOL =0.4V Pins 12, 13, 15, 16 Differential at Vbias=AVDD3-800mV differential operation differential operation single-ended operation single-ended operation single-ended operation programmable (see text) Pins 40, 41 AVDD31600 AVDD3800 3 30 AVDD3400 pF KΩ V mV Differential differential operation differential operation Rev. PrA | Page 5 of 78 AD9549 SYSTEM CLOCK INPUT SYSCLK PLL BYPASSED Input Capacitance (DC) Input Impedance (DC) Common Mode Input Voltage3 Differential Input Voltage Swing3 Input Voltage High (VIH) Input Voltage Low (VIL) Input Current SYSCLK PLL ENABLED Input Capacitance (DC) Input Impedance (DC) Common Mode Input Voltage3 Differential Input Voltage Swing3 Input Voltage High (VIH) Input Voltage Low (VIL) Input Current CRYSTAL RESONATOR WITH SYSCLK PLL ENABLED Motional Resistance CLOCK OUTPUT DRIVERS HSTL OUTPUT DRIVER Differential Output Voltage Swing4 Common Mode Output Voltage4 Continuous Output Current CMOS OUTPUT DRIVER Output Voltage High (VOH) Output Voltage Low (VOL) Output High Current (IOH) Output Low Current (IOL) TOTAL POWER DISSIPATION All Blocks Running Power-Down Mode Default with SysClk PLL Enabled Default with SysClk PLL Disabled - with Digital Power Down - with REFA or REFB Power Down - with HSTL Clock Driver Power Down - with CMOS Clock Driver Power Down - with HSTL 2x Freq. Multiplier Power Down Must be ≤ 0V relative to AVDD3 (pin 14) and ≥ 0V relative to AVSS (pins 33, 43). Must be ≤ 0V relative to AVDD (pin 42) and ≥ 0V relative to AVSS (pins 33, 43). Relative to AVSS (pins 33, 43). 4 Must be ≤ 0V relative to AVDD (pin 36) and ≥ 0V relative to AVSS (pins 33, 43). 5 See “Power Management” Section for details about power profiles. 1 2 3 Preliminary Technical Data 1.5 1 pF KΩ single-ended, each pin differential differential operation differential operation single-ended operation single-ended operation single-ended operation single-ended, each pin differential differential operation differential operation single-ended operation single-ended operation single-ended operation 3 2 pF KΩ kΩ TBD TBD 700 0.9 7.2 mV V mA V V µA µA mW mW mW mW mW mW mW mW mW Both pins AC-coupled using 0.01uF, then 50Ω to GND, 0.4 TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD Using either the Power Down Register or PWRDOWN pin. After reset or power up with fS=1GHz, S4=0, S1-S3=1, fSYSCLK=25MHz After reset or power up with fS=1GHz, S4-S4=1, & Sysclk PLL powered down. One reference still powered up. Rev. PrA | Page 6 of 78 Preliminary Technical Data AC SPECIFICATIONS AD9549 Unless otherwise noted: fS=1GHz. DAC RSET=10KΩ. Power supply pins within the range specified in “DC SPECIFICATIONS.” Table 2. Parameter REFERENCE INPUTS Frequency Range Minimum Slew Rate Minimum Pulse Width High Minimum Pulse Width Low FDBK INPUT Input Frequency Range Minimum Slew Rate Minimum Differential Input Level SYSTEM CLOCK INPUT SYSCLK PLL BYPASSED Input Frequency Range Minimum Pulse Width High Minimum Pulse Width Low Minimum Differential Input Level SYSCLK PLL ENABLED VCO Frequency Range – Low Band VCO Frequency Range – High Band Maximum Input Rate of PFD Without Bipolar Edge Detector Input Frequency Range Multiplication Range Minimum Pulse Width High Minimum Pulse Width Low Minimum Differential Input Level With Bipolar Edge Detector Input Frequency Range Multiplication Range Input Duty Cycle Minimum Differential Input Level CRYSTAL RESONATOR WITH SYSCLK PLL ENABLED Crystal Resonator Frequency Range Maximum Crystal Motional Resistance Min .008 Typ Max 750 Unit MHz V/ns ps ps MHz V/ns V Pins 40, 41 sinusoidal (without degrading phase noise performance) peak-to-peak (xxxdBm into 50Ω) Pins 27, 28 Test Conditions/Comments Pins 12, 13, 15, 16 TBD 1000 MHz ps ps V MHz MHz MHz MHz peak-to-peak (xxxdBm into 50Ω) 700 800 850 1000 100 TBD 66 TBD 8 integer multiples of 2 ps ps V peak-to-peak (xxxdBm into 50Ω) TBD 16 TBD 132 MHz integer multiples of 4 % V peak-to-peak (xxxdBm into 50Ω) fundamental mode resonator see text for recommendations 10 TBD 40+ MHz Rev. PrA | Page 7 of 78 AD9549 CLOCK DRIVERS HSTL OUTPUT DRIVER Toggle Rate Output Duty Cycle Output Rise/Fall Time JITTER HSTL OUTPUT DRIVER WITH 2X MULTIPLIER Output Frequency Range Duty Cycle Sub-harmonic Spur Level JITTER CMOS OUTPUT DRIVER (AVDD3/PIN 37) @3.3V Toggle Rate Duty Cycle Output Rise/Fall Time JITTER CMOS OUTPUT DRIVER AT (AVDD3/PIN 37) @1.8V Toggle Rate Duty Cycle Output Rise/Fall Time JITTER HOLDOVER Frequency Accuracy (XTAL) Variation Over Temperature range Variation Over Supply range Frequency Accuracy (TCXO) Variation Over Temperature range Variation Over Supply range OUTPUT FREQUENCY SLEW LIMITER Slew Rate Resolution Slew Rate Range REFERENCE MONITORS LOSS OF REFERENCE MONITOR Operating Frequency Range Minimum Frequency Error for Continuous “REF” Present” Indication Minimum Frequency Error for Continuous “REF” Present” Indication Maximum Frequency Error for Continuous “REF Lost” Indication Maximum Frequency Error for Continuous “REF Lost” Indication REFERENCE QUALITY MONITOR Operating Frequency Range Frequency Resolution (normalized) Frequency Resolution (normalized) VALIDATION TIMER Rev. PrA | Page 8 of 78 Preliminary Technical Data TBD 48 TBD 0.6 TBD 45 -35 725 52 MHz % ps ps MHz % dBc see plot for maximum toggle rate 100Ω terminated, 5pF load Fin=25 MHz, Fout=200 MHz TBD 55 without correction Fin=25 MHz, Fout=200 MHz see plot for maximum toggle rate With 20pF load and up to 50 MHz Fin=25 MHz, Fout=50 MHz 55 100 60 MHz % ps 55 50 60 MHz % ps see plot for maximum toggle rate With 20pF load and up to 50 MHz Fin=25 MHz, Fout=50 MHz xxxMHz, xxxppm crystal resonator at SYSCLK pins ppm/oC ppm/V TCXO at SYSCLK pins 0 0 0.54 0 111 3x1016 ppm/oC ppm/V Hz/sec Hz/sec P=216 for minimum; P=25 for maximum P=216 for minimum; P=25 for maximum 7.63x103 167x106 -16 -19 Hz ppm % ppm % fREF= 8 kHz fREF= 155 MHz fREF= 8 kHz fREF= 155 MHz -32 -35 0.001 0.002 16 44.9 ppm % fREF= 8 kHz; M=15 for minimum; M=1 for maximum (see text) fREF= 155 MHz; M=15 for minimum; M=1 for maximum (see text) Preliminary Technical Data Timing range Timing range 32x10-9 65x10-6 137 2.8x105 s s PIO= 5 (see text) PIO= 16 (see text) AD9549 Rev. PrA | Page 9 of 78 AD9549 DAC OUTPUT CHARACTERISTICS DCO Frequency range (1st Nyquist zone) Output Resistance Output Capacitance Full-Scale Output Current Gain Error Output Offset Voltage Compliance Range Wideband SFDR (DC to Nyquist): 10MHz Analog Out 40MHz Analog Out 80MHz Analog Out 120MHz Analog Out 160MHz Analog Out Narrowband SFDR 10 MHz Analog Out (±1 MHz) 40 MHz Analog Out (±1 MHz) 80 MHz Analog Out (±1 MHz) 120 MHz Analog Out (±1 MHz) 160 MHz Analog Out (±1 MHz) DIGITAL PLL Minimum open-loop bandwidth TBD TBD TBD TBD TBD TBD TBD TBD TBD TBD 0.0001 dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc kHz Preliminary Technical Data 10 50 5 10 TBD AVSS −0.50 +0.5V 450 MHz Ω pF mA %FS µA DPLL loop bandwidth sets lower limit single-ended (each pin internally terminated to AVSS) range depends on DAC RSET resistor 31.7 TBD 0.6 AVSS +0.50 Outputs not DC shorted to Vss SFDR may be improved by activating Harmonic Spur Suppression (see text) Maximum open-loop bandwidth 100 kHz Minimum phase margin 10 degrees Maximum phase margin 85 degrees dependent on the frequency of REFA/B, the DAC sample rate, and the P, R, and S divider values dependent on the frequency of REFA/B, the DAC sample rate, and the P, R, and S divider values dependent on the frequency of REFA/B, the DAC sample rate, and the P, R, and S divider values (not a hard limit but bounded by 0°) dependent on the frequency of REFA/B, the DAC sample rate, and the P, R, and S divider values (not a hard limit but bounded by 90°) 1,2,..,65,535 or 2,4,..,131,070 1,2,..,65,535 or 2,4,..,131,070 PFD input frequency range Feedforward divider ratio Feedback divider ratio LOCK DETECTION PHASE LOCK DETECTOR Time Threshold Programming Range Time Threshold Resolution Lock Time Programming Range Unlock Time Programming Range FREQUENCY LOCK DETECTOR Normalized Frequency Threshold Programming Range Normalized Frequency Threshold ~0.008 1 1 ~24.5 131,070 131,070 MHz 0 0.488 32x10-9 64x10-6 0 5x10-13 2097 68.7 16.8 0.0021 µs ps s ms FPFD_Gain=200 FPFD_Gain=200 in power-of-2 steps in power-of-2 steps FPFD_Gain=200; normalized to (fREF/R)2; see text for details FPFD_Gain=200; normalized to (fREF/R)2; Rev. PrA | Page 10 of 78 Preliminary Technical Data Programming Resolution Lock Time Programming Range Unlock Time Programming Range 32x10-9 64x10-6 68.7 16.8 s ms see text for details in power-of-2 steps in power-of-2 steps AD9549 Rev. PrA | Page 11 of 78 AD9549 DIGITAL TIMING SPECIFICATIONS Time Required to Enter Power Down Time Req’d to Recover from Power Down S0-4 Config Setup Time During Reset S0-4 Config Hold Time During Reset Reset assert to S0-4 High-Z Time Reset deassert to S0-4 Low-Z time CS to SCLK Setup Time Period of SCLK TDSU (Serial Data Setup Time) TDHD (Serial Data Hold Time) TDV (Data Valid Time) PROPAGATION DELAY FDBK to HSTL Output Driver FDBK to HSTL Output Driver with 2x Frequency Multiplier Enabled FDBK to HSTL Output Driver with 2x Frequency Multiplier Enabled FDBK to CMOS Output Driver FDBK through S-Divider to CMOS Output Driver TBD 10 TBD TBD TBD Preliminary Technical Data ns ns ns ns ns ns ns ns ns ns ns Time S0-4 must be present before falling edge of signal on RESET pin. Time S0-4 must be held after falling edge of signal on RESET pin. Time from rising edge of RESET to High Z on S0-4 configuration pins. Time from falling edge of RESET to Low-Z on S0-4 configuration pins. Rev. PrA | Page 12 of 78 Preliminary Technical Data TYPICAL PERFORMANCE CHARACTERISTICS Unless otherwise noted: AVDD, AVDD3, and DVDD at nominal supply voltage; fS= 1 GHz, DAC RSET= 10kΩ. AD9549 Plot 1: Additive Phase Noise at HSTL Output Driver. Sysclk=1 GHz (SysClk PLL Bypassed). Ref=19.44 MHz., Fout=311.04 MHz. DPLL loop BW= 1 kHz. Plot 2: Additive Phase Noise at HSTL Output Driver. Sysclk=1 GHz (SysClk PLL Bypassed). Ref=19.44 MHz., Fout=622.08 MHz, DPLL loop BW= 1 kHz. HSTL Output Doubler Enabled Rev. PrA | Page 13 of 78 AD9549 Preliminary Technical Data Plot 3: Additive Phase Noise at HSTL Output Driver. Sysclk = 1 GHz (SysClk PLL Enabled and driven by 25 MHz Wenzel Oscillator.) Ref=19.44 MHz., Fout=311.04 MHz, DPLL loop BW= 1 kHz. Plot 5: Additive Phase Noise at HSTL Output Driver. Sysclk = 1 GHz. (Sysclk PLL enabled and driven with 25MHz Wenzel Oscillator.) Fin=19.44 MHz, Fout=155.52 MHz. DPLL loop BW=1 kHz Plot 4: Additive Phase Noise at HSTL Output Driver. Sysclk= 1 GHz (SysClk PLL Enabled and driven by 25 MHz Wenzel Oscillator.). Ref=19.44 MHz., Fout=622.08 MHz, DPLL loop BW= 1 kHz. HSTL Doubler Enabled. Plot 6: Additive Phase Noise at HSTL Output Driver. Sysclk = 500 MHz. Sysclk PLL disabled. Fin=8 kHz, Fout= 155.52 MHz. DPLL loop BW= 400 Hz. Rev. PrA | Page 14 of 78 Preliminary Technical Data AD9549 Plot 7: Additive Phase Noise at HSTL Output Driver. Sysclk = 1 GHz. (Sysclk PLL enabled and driven with 25MHz Fox Crystal Oscillator.) Fin=19.44 MHz, Fout=155.52 MHz. DPLL loop BW=1 kHz. Plot 9: SFDR vs Fout at Sysclk = 1GHz with and w/o recon filter. Fcut = Fout * 1.2 Plot 8: Additive Phase Noise at CMOS Output Driver. Sysclk= 500 MHz. Sysclk PLL disabled. Fin=10.24 MHz, Fout=10.24 MHz. DPLL loop BW=1 kHz Plot 10: HSTL Output Amplitude vs. Toggle Rate (100 ohms across differential pair.,) Rev. PrA | Page 15 of 78 AD9549 2.5 AD9549 CMOS 1.8V Driver w/ 20pF Load: Amplitude vs. Frequency Loaded with 20k Ohm Scope Probe Preliminary Technical Data 2.0 P k -P k ( V o lt s ) 1.5 1.0 Nom Skew 25ºC 1.8V Supply DUT 2 (20pF) 0.5 Slow Skew 90ºC 1.7V Supply DUT 3 (20pF) 0.0 0 20 40 60 80 100 Output Frequency (MHz) Plot 12: CMOS Output Driver Amplitude vs. Toggle Rate (AVDD3 = 3.3V). Plot 11: CMOS Output Driver Amplitude vs. Toggle Rate (AVDD3 = 1.8 V) with 20 pF Load. Rev. PrA | Page 16 of 78 Preliminary Technical Data ABSOLUTE MAXIMUM RATINGS Table 1. Parameter Analog Supply Voltage (AVDD) Digital Supply Voltage (DVDD) Digital I/O Supply Voltage (DVDD_I/0) DAC Supply Voltage (DAC_VDD) Maximum Digital Input Voltage Storage Temperature Operating Temperature Range Lead Temperature Range (Soldering 10 sec) Junction Temperature Thermal Resistance (ΘJA) 1 AD9549 Rating 2V 2V 3.6 V 3.6 V −0.5 V to DVDD_I/O + 0.5 V −65°C to +150°C −40°C to +85°C 300°C 150°C 26°C/W typ. ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulates on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other condition s above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 1 The exposed pad on bottom of package must be soldered to ground in order to achieve the specified thermal performance. Rev. PrA | Page 17 of 78 AD9549 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SCLK SDIO SDO CSB IO_UPDATE RESET PWRDOWN HOLDOVER REFSELECT S4 S3 AVDD AVSS IOUTB IOUT AVDD3 DVDD_I/O DVSS DVDD DVSS DVDD DVSS DVDD DVSS S1 S2 AVDD REFA_IN REFA_INB AVDD3 REFB_IN REFB_INB Preliminary Technical Data DAC_RSET AVDD3 AVDD3 AVDD N/C AVSS AVDD FDBK_IN FDBK_INB AVSS OUT_CMOS AVDD3 AVDD OUT OUTB AVSS Table 2: Pin Function Descriptions Pin No. 1 2, 4, 6, 8 3, 5, 7 9, 10, 54, 55 11, 19, 2326, 29, 30, 36, 42, 45, 53 Input/ Output I I I I/O I Pin Type Power Power Power 3.3V CMOS Power Mnemonic DVDD_I/O DVSS DVDD S1, S2, S3, S4 AVDD Description I/O Digital Supply Digital Ground: Connect to Ground Digital Supply Configurable I/O pins: These pins are configured under program control (see “Status and Warnings” on Page 48. Analog Supply: Connect to a nominal 1.8V Supply N/C N/C AVDD PFD_VRB PFD_VRT PFD_RSET AVDD AVDD AVDD AVDD SYSCLK SYSCLKB AVDD AVDD LOOP_FILTER CLKMODESEL Figure 3: 64-Lead LFCSP Pin Configuration Rev. PrA | Page 18 of 78 Preliminary Technical Data 12 13 14, 37, 46, 47, 49 15 I I I I Diff Input Diff Input Power REFA_IN REFA_INB AVDD3 REFB_IN AD9549 Frequency/Phase Reference A Input. This internally biased input is typically AC-coupled, and when configured as such, can accept any differential signal. Complementary Frequency/Phase Reference A Input: Complementary signal to the input provided on pin 12 Analog Supply: Connect to a nominal 3.3V supply Frequency/Phase Reference B Input. This internally biased input is typically AC-coupled, and when configured as such, can accept any differential signal whose single-ended swing is between 0.4 and 3.3V. Complementary Frequency/Phase Reference B Input: Complementary signal to the input provided on pin 15 No Connects: These are excess, unused pins that may be left floating These pins must be capacitively decoupled. See the Phase Detector Pin Connections section for details. Connect a 5kΩ resistor from this pin to Ground (see the Phase Detector Pin Connections section). System Clock Input Complementary System Clock: Complementary signal to the input provided on pin 27 System Clock Multiplier Loop Filter: When using the frequency multiplier to drive the System Clock, an external loop filter must be constructed and attached to this pin. Clock Mode Select. Set to GND when using a crystal. Pull up to 1.8V when using either an oscillator or external clock source. (See the SysClk Inputs section for details on the use of this pin). Analog Ground: Connect to Ground. NOTE: Pin 43 is a ground shield connection. Complementary HSTL Output: See spec table and the OUTPUT DRIVERS AND MULTIPLIER section, under sub heading Primary (Differential) Driver, for details HSTL Output: See specification table and the CLOCK DRIVERS section CMOS Output: See specification table and the CLOCK DRIVERS section Complementary Feedback input: In standard operating mode, this pin is connected to the filtered IOUTB output . This internally biased input is typically AC-coupled, and when configured as such, can accept any differential signal. Feedback Input: In standard operating mode, this pin is connected to the filtered IOUT output DAC output current setting resistor. Connect a resistor from this pin to GND . See the “DAC Output” section. DAC output: Output signal should be filtered and sent back on chip through FDBK_INB input Complimentary DAC output: Output signal should be filtered and sent back on chip through FDBK_IN input Reference Select input: In manual mode, the REFSELECT pin operates as a high impedance input pin, while in automatic mode, it operates as a low impedance output pin. Logic 0 (low) indicates/selects RefA. Logic 1 (high) indicates/selects RefB. Holdover: (Active high) In manual holdover mode, this pin is used to force the AD9549 into holdover mode. In automatic holdover mode, it indicates holdover status. Power Down: When this active high pin is asserted, the device becomes inactive and enters a low power state. Chip Reset: When this active high pin is asserted, the chip goes into reset. Note: upon power up, a 10 us reset pulse is automatically generated when the power supplies reach a threshold and stabilize. I/O Update: A logic transition from 0 to 1 on this pin transfers data from the I/O port Rev. PrA | Page 19 of 78 16 17, 18 20, 21 22 27 28 31 32 I REFB_INB N/C PFD_VRB, PFD_VRT PFD_RSET SYSCLK SYSCLKB LOOP_FILTER 1.8V CMOS GND 1.8V HSTL 1.8V HSTL 3.3V CMOS CLKMODESEL O I I I set Res I 33, 39, 43, 52 34 35 38 40 I O O O I AVSS OUTB OUT OUT_CMOS FDBK_INB 41 48 50 51 56 I O O O I/O 3.3V CMOS 3.3V CMOS 3.3V CMOS 3.3V CMOS 3.3V FDBK_IN DAC_RSET IOUT IOUTB REFSELECT 57 58 59 I/O I I HOLDOVER PWRDOWN RESET 60 I IO_UPDATE AD9549 CMOS 61 I 3.3V CMOS 3.3V CMOS 3.3V CMOS 3.3V CMOS CSB Preliminary Technical Data registers to the control registers (see the Write subsection of the General Operation of Serial Control Port section). Chip Select: Active low. When programming a device, this pin must be held low. In systems where more than one AD9549 is present this enables individual programming of each AD9549 Serial Data Output: When the device is in three wire mode, data is read on this pin Serial Data Input/Output: When the device is in three-wire mode, data is written via this pin. In 2 wire mode, data reads and writes both occur on this pin Serial Programming Clock: data clock for serial programming. 62 63 64 O I/O O SDO SDIO SCLK Rev. PrA | Page 20 of 78 Preliminary Technical Data INPUT / OUTPUT TERMINATION RECOMMENDATIONS AD9549 0.01 uF Downstream Device (High-Z) 0.01 uF AD9549 1.8V HSTL Output 100Ω 0.01 uF 100Ω (Opt.) AD9549 Self-biasing REF Input 0.01 uF Figure 4: AC-Coupled HSTL Output Driver (Recommended) Figure 6: Reference Input. 0.1 uF 50Ω AD9549 1.8V HSTL Output + Downstream Device (High-Z) AVDD/2 100Ω - AD9549 Self-biasing FDBK Input 50Ω 0.1 uF Figure 5: DC-Coupled HSTL Output Driver Figure 7: FDBK Input. Rev. PrA | Page 21 of 78 AD9549 THEORY OF OPERATION Preliminary Technical Data CMOS CLK_OUT HSTL CLK_OUT 2X ÷S REF_SELECT Freq Est. Digital PLL Core FDBK REF_A ÷R REF_B LOCK DETECT PFD FREQ TUNING WORD PROG. DIGITAL LOOP FILTER SLEW LIMIT DDS/DAC EXTERNAL ANALOG LOW-PASS FILTER INPUT REF MONITOR REF_CNTRL HOLDOVER OOL&LOR CONTROL LOGIC LOW NOISE CLOCK MULTIPLIER S1-S4 IRQ & Status Logic SYSCLK PORT AMP DIGITAL INTERFACE HOLDOVER SYS_CLK Figure 8: Detailed Block Diagram OVERVIEW The AD9549 provides a clocking output which is directly related in phase and frequency to the selected (active) reference (REF_A or REF_B), but having a phase noise spectrum primarily governed by the system clock. A wide band of reference frequencies is supported. Jitter existent on the active reference is greatly reduced by a programmable digital filter in the Digital Phase Locked Loop (PLL), which is the core of this product. The AD9549 supports both manual and automatic holdover. While in holdover, the AD9549 will continue to provide an output as long as the system clock is maintained. The frequency of the output during holdover is an average of the steady state output frequency prior to holdover. Also offered are manual and automatic switchover modes for changing between the two references should one become suspect or lost. A digitally controlled oscillator (DCO) is implemented using a Direct Digital Synthesizer (DDS) with an integrated output DAC, clocked by the system clock. A bypassable PLL based frequency multiplier is present enabling use of an inexpensive, low frequency source for the system clock. For best jitter performance, the system clock PLL should be bypassed, and a low-noise high-frequency system clock should be provided directly. Sampling theory sets an upper bound for the DDS output frequency at 50% of fS (where fS is the DAC sample rate), but a practical limitation of 40% of fS is generally recommended to allow for the selectivity of the required off-chip reconstruction filter. The output signal from the reconstruction filter is fed back to the AD9549, both to complete the PLL, and to be processed through the output circuitry. The output circuitry includes HSTL and CMOS output buffers, as well as a frequency doubler for systems, which need to provide frequencies above the Nyquist level of the DDS. The individual functional blocks are described in the following sections. Rev. PrA | Page 22 of 78 Preliminary Technical Data PLL CORE (DPLLC) The Digital Phase Locked Loop Core (DPLLC) includes the frequency estimation block and the digital phase lock control block driving the DDS. The start of the DPLLC signal chain is the reference signal, fR, which appears on REF A or REF B inputs. The frequency of this signal can be divided by an integer factor of R via the feedforward divider. The output of the feedforward divider is routed to the phase/frequency detector (PFD). Therefore, the frequency at the input to the PFD is given by AD9549 f PFD = fR R . Figure 9: AD9549 Digital PLL Block Diagram The PFD outputs a time series of digital words that are routed to the digital loop filter. The digital filter implementation offers many advantages: The filter response is determined by numeric coefficients rather than discrete component values. There is no aging of components and therefore, no drift of component value over time. There is no thermal noise in the loop filter, and there is no control node leakage current (which causes reference feed through in a traditional analog PLL). The output of the loop filter is a time series of digital words. These words are applied to the frequency tuning input of a DDS to steer the DCO frequency. The DDS provides an analog output signal via an integrated DAC, effectively mimicking the operation of an analog VCO. The DPLLC can be programmed to operate in conjunction with an internal frequency estimator to help decrease the time required to achieve lock. When the frequency estimator is employed, frequency acquisition is accomplished in a two-step process: Step 1: An estimate is made of the frequency of fPFD. The phaselock control loop is essentially inoperative during the frequency estimation process. Once a frequency estimate is made, it is delivered to the DDS so that its output frequency is approximately equal to fPFD multiplied by S (the modulus of the feedback divider). Step 2: The phase-lock control loop becomes active and acts as a servo to acquire and hold phase lock with the reference signal. As mentioned in step 1) above, the DPLLC includes a feedback divider that allows the DCO to operate at an integer multiple (S) of fPFD. This establishes a nominal DCO frequency (fDDS) given by: S f DDS = ( R ) f R . Feedforward Divider (Divide-by-R) The feedforward divider is an integer divider allowing frequency prescaling of the REF Source input signal while maintaining the desired low jitter performance of the AD9549. The feedforward divider is a programmable modulus divider with very low jitter injection. The divider is capable of handling input frequencies as high as 750 MHz. The divider depth is 16bits cascaded with an additional divide-by-two. The divider therefore is capable of integer division from 1 to 65,535 (index of 1) or 2 to 131,070 (index of 2). The divider is programmed via the I/O Register Map to trigger on either the rising (default) or falling edge of the REF Source input signal. There is a lower bound on the value of R imposed by the phasefrequency detector within the DPLLC which has a maximum operating frequency of fPFD[max] as explained in the Fine Phase Detector section. The “R Divider /2” bit must be set when REF_A or REF_B is greater than 400 MHz. The user must also ensure that R is chosen so that it satisfies the inequality: R ≥ ceil(fR / fPFD[max]) The upper bound is: R ≤ floor(fR /8 kHz) Where the ceil(x) function yields the nearest integer ≥ x. For example, if fR=155 MHz and fPFD[max] =24.5 MHz, then ceil (155/24.5) = 7, so R must be > 7. Feedback Divider (Divide-by-S) The feedback divider is an integer divider allowing frequency multiplication of the REF signal that appears at the input of the phase detector. It is capable of handling frequencies well above the Nyquist limit of the DDS. The divider depth is 16-bits cascaded with an additional divide-by-two. The divider is therefore capable of integer division from 1 to 65,535 (index of Rev. PrA | Page 23 of 78 AD9549 1) or 2 to 131,070 (index of 2). The divider is programmed via the I/O Register Map to trigger on either the rising (default) or falling edge of the feedback signal. The feedback divider must be programmed within certain boundaries. The “S Divider /2” bit must be set when FDBK_IN is greater than 400 MHz. The upper boundary on the feedback divider is the lesser of the maximum programmable value of S and the maximum practical output frequency of the DDS (~ 40%fS). Two formulae are given: Smax1 for a feedback divider index of 1 and Smax2 for an index of 2: Preliminary Technical Data condition, the phase error measurement uses the coarse phase detector instead. Digital Loop Filter The digital loop filter integrates and low-pass filters the digital phase error values delivered by the phase detector. The loop filter response mimics that of a 2nd order, R-C network used to filter the output of a typical phase detector and charge pump combination as shown in the diagram below. CLK Loop Filter Phase/ Frequency Detector Charge Pump C1 R2 C2 S max 1 = min S max 2 ( = min [ 40% f S R fR 40% f S R fR , 65535 ) VCO , 131070 ] or Where R is the modulus of the feedforward divider, fS is the DAC sample rate, and fR is the input reference frequency. Figure 10: Typical Analog PLL Block Diagram The DCO has a minimum frequency (see DAC output Characteristics section of AC specification table). This imposes a lower bound, Smin, on the feedback divider value, as well. S min = max R (( f DCO min fR ), 1) NOTE: Reduced DCO frequencies result in worse jitter performance (a consequence of the reduced slew rate of the sinusoid generated by the DDS). Forward and Reverse FEC Clock Scaling The Feedforward (Divide-by-R) and Feedback Divider (Divideby-S) enable FEC clock scaling. For instance, to multiply the incoming signal by 255/237, set the S- divider to 255, and the R-divider to 237. One should be careful to abide by the limitations on the R- and S-Dividers, and make sure the Phase Detector input frequency is within specified limits. The building blocks implemented on the AD9549, however, are digital. A time-to-digital converter that produces digital values proportional to the edge timing error between the CLK and feedback signals replaces the phase-frequency detector and charge pump. A digital filter that processes the edge timing error samples from the time-to-digital converter replaces the loop filter. A DDS replaces the VCO, which produces a frequency that is linearly related to the digital value provided by the loop filter. This is shown in Figure 11 on Page 26 with some additional detail. The samples provided by the time-to-digital converter are delivered to the loop filter at a sample rate equal to the CLK frequency (i.e., fR/R). The loop filter is intended to oversample the time-to-digital converter output at a rate determined by the "P"-divider. The value of P is programmable via the I/O Register Map. It is stored as a 5-bit number, PIO. The value of PIO is related to P by the equation: P = 2P IO Phase Detector The phase detector is composed of two detectors: a coarse phase detector and a fine phase detector. The two detectors operate in parallel. Both detectors measure the duration (∆t) of the pulses generated by a conventional 3-state phase/frequency detector. Together, the fine and coarse phase detectors produce a digital word that is a time-to-digital conversion of the separation between the edge transitions of the pre-scaled reference signal and the feedback signal. If the fine phase detector is able to produce a valid result, then this result alone serves as the phase error measurement. If the fine phase detector is either in an overflow or underflow (where 5 ≤ PIO ≤ 16) Hence, the "P"-divider can provide divide ratios between 32 and 65536 in power-of-2 steps. With a DAC sample rate of 1GHz the loop filter sample rate can range from as low as 15.26kHz to a maximum of 31.25MHz. Coupled to the loop filter is a cascaded comb-integrator (CCI) filter that provides a sample rate translation between the loop filter sample rate (fS/P) and the DDS sample rate, fS. Rev. PrA | Page 24 of 78 Preliminary Technical Data The choice of P is important because it controls both the response of the CCI filter and the sample rate of the loop filter. In order to understand the method for determining a useful value for P, it is first necessary to examine the transfer function of the CCI filter: AD9549 define PMAX in terms of PIO, so that PIOMAX may be determined. The condition, PIO ≤ PIOMAX, ensures that the impact of the phase delay of the CCI filter on the phase margin of the loop will not exceed 5°. PIOMAX may be expressed as: PIOMAX = max 5,     f S   2 fS  , floor log 2  min 16, floor log 2  3f  80 f      REF LOOP                H (ω ) CCI = or [ 1− e − jωP P (1− e − jω ) ] 2 1, H CCI (ω ) = 1 1− cos(ωP ) P 2 1− cos(ω ) ω=0 ( ), ω>0 With a properly chosen value for P, the closed-loop response of the digital PLL is primarily determined by the response of the digital loop filter. Flexibility in controlling the loop filter response translates directly into flexibility in the range of applications satisfied by the architecture of the AD9549. To evaluate the response in terms of absolute frequency, make the substitution: ω= 2πf fS (where fS is the DAC sample rate and f is the frequency at which HCCI is to be evaluated) Analysis of this function reveals that the CCI magnitude response follows a low pass characteristic that consists of a series of P lobes. The lobes are bounded by null points occurring at frequency multiples of fS/P. The peak of each successive lobe is lower that its predecessor over the frequency range between DC and ½fS. For frequencies greater than ½fS, the response is a reflection about the vertical at ½fS. Furthermore, the first lobe (which appears between DC and fS/P) exhibits a monotonically decreasing response. That is, the magnitude is unity at DC and it steadily decreases with frequency until it vanishes at the first null point (fS/P). The null points imply the existence of transmission zeros placed at finite frequencies. While transmission zeros placed at infinity yield minimal phase delay, zeros placed closer to DC result in increased phase delay. Hence, the position of the first null point has a significant impact on the phase delay introduced by the CCI filter. This is an important consideration, because excessive phase delay negatively impacts the overall closed loop response. As a rule of thumb, choose a value for P so that the frequency of the first null point (fS/P) is the greater of: 80 times the desired loop bandwidth, or 1.5 times the frequency of CLK (fR/R) The value of P thus calculated (PMAX) is the largest usable value in practice. Since P is programmed as PIO, it is necessary to Rev. PrA | Page 25 of 78 AD9549 Direct Digital Synthesizer One of the primary building blocks of the digital PLL is a direct digital synthesizer (DDS). The DDS behaves like a sinusoidal signal generator. The frequency of the sinusoid generated by the DDS is determined by a frequency tuning word (FTW), which is a digital (i.e., numeric) value. Unlike an analog sinusoidal generator, a DDS uses digital building blocks and operates as a sampled system. Thus, it requires a sampling clock (fS) that serves as the DDS's fundamental timing source. The accumulator behaves as a modulo-248 counter with a programmable step size (FTW). A block diagram of the DDS is shown below. Phase Offset 48-bit Accumulator 48 16 19 D Q 19 Preliminary Technical Data ∆φ = 2π ( ∆phase 216 ) The DDS can be operated in either open loop or closed loop mode, via the Close Loop bit in the DPLL Register. There are two open loop modes: Single Tone and Holdover. In Single Tone Mode, the DDS behaves like a frequency synthesizer, and uses the value stored in the FTW0 register to determine its output frequency. Alternatively, the FTW and ∆phase values can be determined by the device itself using the frequency estimator. Because Single Tone mode ignores the reference inputs, it is very useful for generating test signals to aid in debugging. Single Tone mode must be activated manually via register programming. In Holdover mode, the AD9549 uses past tuning words when the loop was closed to determine its output frequency. Therefore, the loop must have been successfully closed in order for Holdover Mode to work. Switching in and out of Holdover Mode can be either automatic or manual, depending on register settings. Typically, the AD9549 operates in closed loop mode. In closed loop mode, the FTW values come from the output of the digital loop filter and vary with time. The DDS frequency is steered in a manner similar to a conventional VCO-based PLL. NOTE: In "closed loop" mode, the DDS phase offset capability is inoperative. I-Set Frequency Tuning Word (FTW) 48 48 Angle to Amplitude Conversion 14 DAC (14-bit) DAC+ DAC- fS Figure 11: DDS Block Diagram The input to the DDS is a 48-bit FTW that provides the accumulator with a seed value. On each cycle of fS, the accumulator adds the value of the FTW to the running total of its output. For example, given an FTW=5, the accumulator would count by 5's, incrementing on each fS cycle. Over time, the accumulator will reach the upper end of its capacity (248 in this case). At which point it rolls over, retaining the excess. The average rate at which the accumulator rolls over establishes the frequency of the output sinusoid. The average rollover rate of the accumulator is given by the formula below, and establishes the output frequency (fDDS) of the DDS. f DDS = ( )f FTW 2 48 S Solving this equation for FTW yields:  f FTW = round 2 48  DDS    fS     For example, given that fS=1GHz and fDDS=19.44MHz, then FTW=5,471,873,547,255 (04FA05143BF7h). The relative phase of the sinusoid can be controlled numerically, as well. This is accomplished using the phase offset input to the DDS (a programmable 16-bit value (∆phase); see the I/O Register Map). The resulting phase offset, ∆φ (radians), is given by: Rev. PrA | Page 26 of 78 Preliminary Technical Data DAC Output The output of the digital core of the DDS is a time series of numbers representing a sinusoidal waveform. This series is translated to an analog signal by means of a digital-to-analog converter (DAC). The DAC outputs its signal to two pins driven by a balanced current source architecture (see DAC output diagram below). The peak output current derives from the combination of two factors. The first is a reference current (IDAC_REF) established at the DAC_RSET pin and the second is a scale factor programmed into the I/O Register map. AVDD3 49 AD9549 I DAC _ FS = I DAC _ REF (72 + 192⋅FSC ) 1024 Using the recommended value of RDAC_REF the full-scale DAC output current can be set with 10-bit granularity over a range of approximately 8.6mA to 31.7mA. PHASE DETECTOR Coarse Phase Detector The coarse phase detector uses the DAC sample rate (fS) to determine the edge timing deviation between the REF signal and the feedback signal generated by the DDS. Hence, fS sets the timing resolution of the coarse phase detector. At the recommended rate of fS=1GHz, the coarse phase detector spans a range of over 131µs (sufficient to accommodate REF signal frequencies as low as 8 kHz). The phase gain of the coarse phase detector is controlled via the I/O Registers by means of two numeric entries. The first is a 3bit power-of-2 scale factor, PDS. The second is a 6-bit linear scale factor, PDG. IFS IFS/2 IFS/2 Current Switch Array IFS/2 + ICODE Switch Control Current Switch Array IFS/2 - ICODE Phase GainCPD = R Fine Phase Detector ( )(2 fS fR PDS + 6 PDG ) CODE 51 IOUT IOUTB 50 The fine phase detector operates on a divided down version of fS as its sampling time base. The sample rate of the fine phase detector is set using a 4-bit word (PFD_Div) in the I/O Register Map and is given by: 50 52 50 Fine Phase Detector Sample Rate = fS 4 ( PFD _ Div ) AVSS Figure 12: DAC Output Pins The default value of PFD_Div is 5, so for fS=1GHz, the default sample rate of the fine phase detector is 50MHz. The upper bound on the maximum allowable input frequency to the phase detector (fPFD[max]) is 49% of the sample rate, or: The value of IDAC_REF is set by connecting a resistor (RDAC_REF) between the DAC_RSET pin and ground. The DAC_RSET pin is internally connected to a virtual voltage reference of 1.2v nominal, so the reference current can be calculated by: f PFD[max] = fS 8( PFD _ Div ) Therefore, fPFD[max] is 25MHz in the example above. The fine phase detector uses a proprietary technique to determine the phase deviation between the REF signal and feedback signal. I DAC _ REF = 1.2 RDAC _ REF NOTE: The recommended value of IDAC_REF is 120µA, which leads to a recommended value of RDAC_REF of 10kΩ. The scale factor consists of a 10-bit binary number (FSC) programmed into the DAC FS Current register in the I/O Register Map. The full-scale DAC output current (IDAC_FS) is then given by: Rev. PrA | Page 27 of 78 AD9549 The phase gain of the fine phase detector is controlled by an 8bit scale factor (FPFD_Gain) in the I/O Register Map. The nominal (default) value of FPFD_Gain is 200, and establishes R (210107 )( FPFD _ Gain ) the phase gain as: PhaseGainFPD = f R Preliminary Technical Data Note that the AD9549 Evaluation Software will calculate register values that have the phase detector gains already matched. Phase Detector Pin Connections There are three pins associated with the phase detector that must be connected to external components. The diagram below shows the recommended component values and their connections. Phase Detector Gain Matching Although the fine and coarse phase detectors use different means to make a timing measurement, it is essential that both have equivalent phase gain. Without proper gain matching the closed-loop dynamics of the system cannot be properly controlled. Hence, the goal is to make PhaseGainCPD= PhaseGainFPD. This leads to: AD9549 PFD_VRB 20 0.1µF 4K99 0.1µF 21 PFD_VRT 22 PFD_RSET (f S 2 PDS + 6 PDG = 21010 7 FPFD _ Gain ) ( ) Which simplifies to: 7 2 PDS PDG = (16⋅10 )FPFD _ Gain fS 10µF 0.1µF Typically, FPFD_Gain is established first and then PDG and PDS are calculated. The proper choice for PDS is given by: PDS = round log 2 [( ( 10 FPFD _ Gain 2 fS 7 )] Figure 13: Phase Detector Pin Connections The final value of PDS must satisfy 0 ≤ PDS ≤ 7. The proper choice for PDG is calculated using this equation: DIGITAL LOOP FILTER COEFFICIENTS In order to provide the desired flexibility, the loop filter has been designed with three programmable coefficients (α, β and γ). The coefficients along with P (where P=2Pio) completely defines the response of the filter, which is given by: PDG = round 10 7 FPFD _ Gain 2 PDS − 4 f S ) The final value of PDG must satisfy 0 ≤ PDG ≤ 63. For example, let fS=700MHz and FPFD_Gain=200, then PDS=1 and PDG=23. H (ω ) LoopFilter = α ( e jω + ( β −γ −1) e j 2 ω + ( − γ − 2 ) e jω + (γ +1) ) To evaluate the response in terms of absolute frequency substitute: ω= 2πPf fS Where P is the divide ratio of the "P"-divider, fS is the DAC sample rate, and f is the frequency at which the function is to be evaluated. Rev. PrA | Page 28 of 78 Preliminary Technical Data The loop filter coefficients are determined by the AD9549 evaluation software according to three parameters: φ: desired closed-loop phase margin (0 < φ < π/2 rad) desired open-loop bandwidth (Hz) fLOOP: desired output frequency of the DDS (Hz) fDDS: Note that fDDS can also be expressed as fDDS = fR(S/R). The three coefficients are calculated according to parameters via the equations below: AD9549 The quantized α coefficient is composed of three factors, where α0, α1 and α2 are the programmed values for the α coefficient: α α quantized = (2048 )(2α )(2 −α 0 1 2 ) The boundary values for each are 0 ≤ α0 ≤ 4095, 0 ≤ α1 ≤ 22, and 0 ≤ α2 ≤ 7. The optimal values of α0, α1 and α2 are: β = −4πPf C tan(φ ) γ = 1 F (φ )β 2 α1 = max[0, min{22, ceil (log 2 2048α 4095 )}] 2 −α1 +11 α 2 = max[0, min{7, floor (log 2 ( 4095 ) + α 1 − 11)}] α DDS α = − 10 Where ( 238 π 7 FPFD _ Gain )f f C F (φ ) β f LOOP fS α 0 = max [0, min{4095, round (α ⋅ 2α , and FPFD_Gain is )}] 1 F (φ ) = 1 + sin(φ ) , f C = The magnitude of the quantized β coefficient is composed of two factors: the value of the gain scale factor for the Fine Phase Detector as programmed into the I/O Register Map. NOTE: The range of loop filter coefficients is limited as follows: 0 < α < 223 (~8.39·106) -0.125 < β < 0 -0.125 < γ < 0 The above constraints on β and γ constrain the closed-loop phase margin such that both β and γ will assume negative values. Even though β and γ are limited to negative quantities, the values as programmed are positive. The negative sign is assumed internally. NOTE: The closed-loop phase margin is limited to the range of 0° < φ < 90° because β and γ are negative. The three coefficients are implemented as digital elements, necessitating quantized values. Determination of the programmed coefficient values in this context follows. β quantized = (β 0 )(2 − ( β +15 ) ) 1 Where β0 and β1 are the programmed values for the β coefficient, The boundary values for each are 0 ≤ β0 ≤ 4095 and 0 ≤ β1 ≤ 7. The optimal values of β0 and β1 are: β 1 = max 0, min 7, floor log 2 [ { ( ( )− 15)}] 4095 β β 0 = max[0, min{4095, round ( β ⋅ 2 β +15 )}] 1 The magnitude of the quantized γ coefficient is composed of − (γ +15 ) two factors: γ quantized = γ 0 2 1 ( )( ) Where γ0 and γ1 are the programmed values for the γ coefficient, the boundary values for each are 0 ≤ γ0 ≤ 4095 and 0 ≤ γ1 ≤ 7. The optimal values of γ0 and γ1 are: γ 1 = max 0, min 7, floor log 2 [ { ( ( )− 15)}] 4095 γ γ 0 = max[0, min{4095, round (γ ⋅ 2 γ +15 )}] 1 Rev. PrA | Page 29 of 78 AD9549 The min(), max(), f loor(), ceil() and round() functions are defined as follows. The function, min(x1, x2, … xn), chooses the smallest value in the list of arguments. The function, max(x1, x2, … xn), chooses the largest value in the list of arguments. The function, ceil(x), increases x to the next higher integer if x is NOT an integer, otherwise x is unchanged. The function, floor(x), reduces x to the next lower integer if x is NOT an integer, otherwise x is unchanged. The function, round(x), rounds x to the nearest integer. To demonstrate the wide programmable range of the loop filter bandwidth, consider the following design example. The system clock frequency (fS) is 1GHz, the input reference frequency (fR) is 19.44MHz, the DDS output frequency (fDDS) is 155.52MHz, and the required phase margin (φ) is 45°. fR is within the nominal bandwidth of the phase detector (25MHz), and fDDS/fR, is an integer (8), so the prescalar is not required. We can therefore use R=1 and S=8 for the feedforward and feedback dividers, respectively. NOTE: If fDDS/fR is a non- integer, then R and S must be chosen such that S/R= fDDS/fR with S and R both constrained to integer values. For example, if fR=10MHz and fDDS=155.52MHz, then the optimal choice for S and R is 1944 and 125, respectively. The open loop bandwidth range under the defined conditions spans 9.5Hz to 257.5kHz. The wide dynamic range of the loop filter coefficients allows for programming of any open loop bandwidth within this range under these conditions. The resulting closed loop bandwidth range under the same conditions is approximately 12Hz to 359kHz. The resulting loop filter coefficients for the upper loop bandwidth along with the necessary programming values are shown below. α = 4322509.4784981 α0 = 2111 (83Fh) α1 = 22 (16h) α2 = 0 (0h) β = -0.10354689386232 β0 = 3393 (D41h) β1 = 0 (0h) γ = -0.12499215775201 γ0 = 4095 (FFFh) γ1 = 0 (0h) Preliminary Technical Data The resulting loop filter coefficients for the lower loop bandwidth along with the necessary programming values are shown below. α = 0.005883404361345 α0 = 1542 (606h) α1 = 0 (00h) α2 = 7 (7h) β = -0.000003820176667 β0 = 16 (10h) β1 = 7 (7h) γ = -0.00000461136116 γ0 = 19 (13h) γ1 = 7 (7h) Details on exactly how these coefficients are derived can be obtained by contacting Analog Devices Inc. directly. CLOSED LOOP PHASE OFFSET The AD9549 provides for limited control over the phase offset between the reference input signal and the output signal by adding a constant phase offset value to the output of the phase detector. An adder is included at the output of the phase detector as shown in the figure below to support this. The value of the constant (PLLOFFSET) is set via the PLL Offset register. Phase Offset Value CLK Feedback Phase Detector Loop Filter To CCI Filter Figure 14: Input Phase Offset Adder PLLOFFSET is a function of the phase detector gain and the desired amount of timing offset (∆tOFFSET). It is given by: PLLOFFSET = ∆t OFFSET 21010 7 FPFD _ Gain ( ) NOTE: FPFD_Gain is described in the Fine Phase Detector section. Rev. PrA | Page 30 of 78 Preliminary Technical Data For example, suppose that FPFD_Gain=200, fCLK=3MHz, and 1° of phase offset is desired. First, we must find the value of ∆tOFFSET, which is: RESET Phase Detector Samples AD9549 ∆t OFFSET = deg 360 TCLK = 1 360 ( 1 3 MHz ) = 925.9 ps Absolute Value Digital Comparator Control Logic Having determined ∆tOFFSET, we have: Unlock Timer Lock Timer Phase Lock Detect PLLOFFSET = 925.9 ps 210 ⋅ 10 7 ⋅ 200 = 1896 The result has been rounded because PLLOFFSET is restricted to integer values. NOTE: The PLLOFFSET value is programmed as a 14-bit, twoscomplement number. However, the user must ensure that the magnitude is constrained to 12 bits, such that: -2 ≤ PLLOFFSET < +2 11 11 ( ) P-Divider Clock 3 5 I/O Registers Phase Lock Detect Threshold Y X Close Loop Figure 15: Phase Lock Detector Block Diagram The Phase Lock Detect Threshold value (PLDT) is a 32-bit number stored in the I/O Register Map: The above constraint yields a timing adjustment range of ±1ns. This ensures that the phase offset remains within the bounds of the fine phase detector. PLDT = round ∆t ⋅ 210 ⋅ 10 7 ⋅ FPFD _ Gain ( ) LOCK DETECTION Phase Lock Detection During the phase locking process, the output of the phase detector tends toward a value of zero, which indicates perfect alignment of the phase detector input signals. As the control loop works to maintain the alignment of the phase detector input signals, the output of the phase detector wanders around zero. The phase lock detector tracks the absolute value of the digital samples generated by the phase detector. These samples are compared to the Phase Lock Detect Threshold value programmed in the I/O Register Map. A false state at the output of the comparator indicates the absolute value of a sample exceeds the value in the threshold register. A true state at the output of the comparator indicates alignment of the phase detector input signals to the degree specified by the lock detection threshold. Where ∆t is the maximum allowable timing error between the signals at the input to the phase detector and the value of FPFD_Gain is as described in the Fine Phase Detector section. For example, suppose that fR/R=3MHz, FPFD_Gain=200, and the maximum timing deviation is given as 1°. This yields a ∆t value of: ∆t = 1o 360o (R ⋅ TR )⋅ = 360R f R = 1 360⋅ 3⋅106 ( ) The resulting phase lock detect threshold is:  2 10 ⋅10 7 ⋅ 200  PLDT = round   360 3 ⋅10 6  = 1896    ( ) Hence, 1896 (00000768h) is the value that must be stored in the Phase Lock Detect Threshold register. The "phase lock detect" signal is generated once the control logic observes that the output of the comparator has been in the true state for 2X periods of the P-Divider clock (see the Digital Loop Filter section for a description of the P-Divider). Once the phase lock detect signal is asserted, it remains asserted until cleared by an "unlock" event or by a device RESET. The duration of the lock detection process is programmable via the Phase Lock Watchdog Timer register. The interval is controlled by a 5-bit number, X (0 ≤ X ≤ 20). The absolute duration of the phase lock detect interval is: TLOCK = Rev. PrA | Page 31 of 78 2X P fS AD9549 Hysteresis in the phase lock detection process is controlled by specifying the minimum duration that qualifies as an unlock event. An unlock event is declared when the control logic observes that the output of the comparator has been in the false state for 2Y+1 periods of the P-Divider clock (provided that the phase lock detect signal has been asserted). Detection of an unlock event clears the phase lock detect signal, and the phase lock detection process is automatically restarted. Preliminary Technical Data The time required to declare an unlock event is programmable via the Phase Lock Watchdog Timer register. The interval is controlled by a 3-bit number, Y (0 ≤ Y ≤ 7). The absolute duration of the unlock detection interval is: TUNLOCK = 2Y + 1 P fS Figure 16 below shows the basic timing relationship between the reference signal at the input to the phase detector, the phase error magnitude, the output of the comparator, and the output of the phase lock detector. The example shown here assumes that X=3 and Y=1. fR/R Phase Error Magnitude Samples 0 Threshold fS/P Threshold Comparator Lock Timer (X=3) Unlock Timer (Y=1) 8 4 8 LOCKED Figure 16: Lock/Unlock Detection Timing Frequency Lock Detection Frequency lock detection is similar to phase lock detection, with the exception that the difference between successive phase samples is the source of information. A running difference of the phase samples serves as a digital approximation to the timederivative of the phase samples, which is analogous to frequency. RESET Phase Detector Samples The formula for the Frequency Lock Detect Threshold value (FLDT) is: 2  R FLDT = round ∆f ⋅ 210107 FPFD _ Gain ⋅    f    R    Differencer Absolute Value Digital Comparator Control Logic Unlock Timer Lock Timer Frequency Lock Detect Where fR is the frequency of the active reference, R is the value of the reference prescaler, and ∆f is the maximum frequency deviation of fR that is considered to indicate a frequency locked condition (∆f ≥ 0). For example, suppose that fR=3MHz, R=5, FPFD_Gain=200, and a frequency lock threshold of 1% is specified. Then the frequency lock detect threshold value is: 2   5  FLDT = round  1% ⋅ 3 ⋅106 ⋅ 210107 ⋅ 200 ⋅    = 170,667 6  3 ⋅10      P-Divider Clock 3 5 ( ) I/O Registers Frequency Lock Detect Threshold Y X Close Loop Figure 17: Frequency Lock Detection Hence, 170667 (00029AABh) is the value that should be stored in the Frequency Lock Detect Threshold register. The duration of the frequency lock/unlock detection process is controlled in exactly the same way as the phase lock/unlock Rev. PrA | Page 32 of 78 Preliminary Technical Data detection process in the previous section. However, a different control register is used: the Frequency Lock Watchdog Timer register. Note that when N is chosen to be AD9549 floor ( ) + 1 , the LOR fS 2 fR REFERENCE MONITORS Loss of Reference The AD9549 can set an alert when one or both of the reference signals are not present. Each of the two reference inputs (REFA, REFB) has a dedicated LOR (Loss of Reference) circuit enabled via the I/O Register Map. Detection of an LOR condition sets the appropriate LOR bit in both a status register and an IRQ register in the I/O Register Map. The LOR state is also internally available to the multi-purpose "status" pins (S1:4) of the AD9549. By setting the appropriate bit in the I/O Register Map, the user can assign a status pin to each of the LOR flags. This provides a means to control external hardware based on the state of the LOR flags directly. The LOR circuits are internal ‘watchdog’ timers with a programmable period. The period of the timer is set via the I/O register Map so that its period is longer than that of the monitored reference signal. The rising edge of the reference signal continuously resets the watchdog timer. If the timer reaches a full count, this indicates that the reference was either lost or its period was longer than the timer period. LOR does not differentiate between these. The period for each of the LOR timers is controlled by a 16-bit word in the I/O Register Map. The period of the timer clock (TCLK) is 2/fS. Therefore, the period of the watchdog timer (TWD) is: TWD = (2/fS)N Where N is the value of the 16-bit word stored in the I/O Register Map for the appropriate LOR circuit. Choose the value of N so that the watchdog period is greater than the input reference period, expressed mathematically as: circuit is capable of indicating an LOR condition in little more than a single input reference period. For example, if fS=1GHz and fR=2.048MHz, then the smallest useable N value is: 10 N MIN = floor 2(2.048×106 ) + 1 = 245 9 ( ) Which yields values for fPRESENT and fLOST as: f PRESENT = 2,048,816 and f LOST = 2,032,520 NOTE: N should be chosen sufficiently large to account for any acceptable deviation in the period of the input reference signal. Notice that the value of N is inversely proportional to the reference frequency, meaning that as the reference frequency goes up, the precision for adjusting the threshold goes down. Proper operation of the LOR circuit requires that N be no less than 3. Therefore, the highest reference frequency for which the LOR circuit will function properly is given by: fLOR_MAX = fS/6. Reference Frequency Monitor The AD9549 can set an alert whenever one or both of the reference inputs drift in frequency beyond user-specified limits. Each of the two references has a dedicated Out of Limits (OOL) circuit enabled/disabled via the I/O Register Map. Detection of an OOL condition sets the appropriate OOL bit in both a status register and an IRQ register in the I/O Register Map. The user can also assign a status pin (S1-S4) to each of the OOL flags by setting the appropriate bit in the I/O Register Map. This provides a means to control external hardware based on the state of the OOL flags directly. Each reference monitor contains three main building blocks: a programmable reference divider, a 32-bit counter, and a 32-bit digital comparator. N > floor () fS 2 fR where fR is the frequency of the input reference. The value of N results in establishing two frequencies. One for which the LOR signal will never be triggered (fPRESENT), and one for which the LOR signal will always be active (fLOST). Between these frequencies the LOR signal will intermittently toggle between states. The values of the two frequency bounds are: Figure 18: Reference Monitor f PRESENT = fS 2N f LOST = fS 2 ( N +1) Four values are needed to calculate the correct values of the reference monitor: The system clock frequency, fS (usually Rev. PrA | Page 33 of 78 AD9549 1 GHz), the reference input frequency, fR (in Hz), the error bound, E (1%=0.01), and the monitor window size (W). The monitor window size is the difference between the maximum and minimum number of counts accumulated between adjacent edges of the reference input. If this window is too small, random variations will cause the OOL detector to indicate incorrectly that a reference is out of limits. However, the time required to determine if the reference frequency is valid increases with window size. A window size of at least 20 is a good starting point. The four input values mentioned above are used to calculate the OOL Divider (D) and OOL nominal value (N), which in turn are used to calculate the OOL Upper Limit (U), and OOL Lower Limit (L) according to the following formulas: Preliminary Technical Data the I/O Register Map. Transition to a newly selected reference depends on a number of factors: State of the REFSELECT pin State of the "Ref_AB" control register bit State of the "Enable Ref Input Override" register bit Holdover status A functional diagram of the reference switchover and holdover logic is shown in Figure 19.  f W D = max(1, min(65535, ceil  4 * R * ))  fS E    N= fR D * fS 4 L = floor ( N ) − floor (W ) U = ceil ( N ) + floor (W ) The timing accuracy is dependent on two factors. The first is the inherent accuracy of fS, since it serves as the time base for the Reference Monitor. As such, the accuracy of the Reference Monitor can be no better than the accuracy of fS. Second, the value of W, which must be sufficiently large so that the timer resolves the deviation between a nominal value of fR and a value that is out of limits. As an example, let fR=10MHz, Ε=1.0%, fS=1GHz, and W=20. The limits are then: Lower Limit = 1980 Upper Limit = 2020 Now let Ε=0.01%, Then the limits are: Lower Limit = 199980 Upper Limit = 200020 Notice that the number of counts (and time) required to make this measurement has increased 100x. REFERENCE SWITCHOVER The AD9549 supports dual input reference clocks. Reference switchover may be accomplished either automatically or manually by appropriately programming the "AutoRefSel" bit in Rev. PrA | Page 34 of 78 Preliminary Technical Data Active RefSel State AD9549 an "Enable Line Card Mode" bit is provided in the I/O Register map. The Line Card Mode logic is shown in Figure 20 below. When Enable Line Card bit is 0, reference switch over occurs on command without consideration to the relative edge placement of the references. This means that there is the possibility of an extra pulse. However, when this bit is set to 1, the timing of the reference switch over is executed conditionally as shown in Figure 21 on Page 36. REFA In To Holdover Control Logic REF SEL RefAB 1 0 Derived RefSel State 1 0 To Reference Switching Control Logic State Machine AutoRefSel AutoHold Derived Holdover State 1 0 Override RefPin Override HldPin 0 1 0 1 selected reference REFB In REF In Hldovr Enable Line-Card Mode HOLDOVER 0 Active Holdover State 1 Q D From Reference Selection Logic Figure 19: Reference Switchover and Holdover Logic In manual mode, the active reference is determined by an externally applied logic level to the REFSELECT pin. In automatic mode, an internal state machine determines which reference is active, and the REFSELECT pin becomes an output indicating which reference the state machine is using. The user may override the active reference chosen by the internal state machine via the "Enable Ref Input Override " bit in the I/O Register Map. The "Ref_AB" bit in the I/O Register Map is then used to select the desired reference. When in override, it is important to note that the REFSELECT pin does not indicate the physical reference selected by the "Ref_AB" bit. Instead, it indicates the reference that the internal state machine would select if the device were not in the override mode. This allows the user to force a reference switchover by means of the programming registers while monitoring the response of the state machine via the REFSELECT pin. The same type of operation (manual/automatic and override) also applies to the holdover function, as shown in the Reference Switchover Logic diagram. The dashed arrows in the diagram indicate that the state machine output is available to the REFSELECT and HOLDOVER pins when in override mode. 0 1 Figure 20: Reference Switchover Control Logic Note that when the line card mode is enabled, the rising edges of the alternate reference are used to clock a latch. The latch holds off the actual transition until the next rising edge of the alternate reference. Shown in Figure 21 is a timing diagram that demonstrates the difference between reference switchover with the line card mode enabled and disabled. If enabled, when the reference switchover logic is given the command to switch to the alternate reference, an actual transition does not occur until the next rising edge of the alternate reference. This action eliminates the spurious pulse that can occur when the line card mode is disabled. Use of Line Card Mode to Eliminate Runt Pulses When two references are not in exact phase alignment and a transition is made from one to the other, it is possible that an extra pulse can be generated. This depends on the relative edge placement of the two references and the point in time that a switch over is initiated. To eliminate the "extra pulse" problem, Rev. PrA | Page 35 of 78 AD9549 REFA In REFB In From Reference Selection Logic REF In REF In 1 2 3 4 Preliminary Technical Data 1=Holdover). The HOLDOVER pin is configured as a high impedance (>100kΩ) input pin in order to accommodate manual holdover operation. Line Card Mode 2 3 4 5 Disabled 1 2 3 Select REFB 4 Select REFA 1 1 2 3 4 Enabled Automatic holdover is invoked when the “AutoHold" bit is a logic 1. In automatic mode, the HOLDOVER pin is configured as a low impedance output with its logic state indicating the holdover state as determined by the internal state machine (0=Normal, 1=Holdover). In automatic holdover operation the user may override the internal state machine by programming the "Override HldPin" bit to a logic 1 and the "Hldovr" bit to the desired state (0=Normal, 1=Holdover). However, the HOLDOVER pin does not indicate the "forced" holdover state in the override condition, but continues to indicate the holdover state as chosen by the internal state machine (even though the state machine choice is overridden). This allows the user to force a holdover state by means of the programming registers while monitoring the response of the state machine via the HOLDOVER pin. A functional diagram of the reference switchover and holdover logic is shown in Figure 19 on Page 35. NOTE: The default state for the reference switchover bits is AutoHold=0, Override HldPin=0, and Hldovr=0. REF selection stalled until next rising edge of REFB Figure 21: Reference Switchover Timing HOLDOVER Holdover Control Holdover functionality provides the user with a means of maintaining the output clock signal even in the absence of a reference signal at the REF A or B input. In holdover mode, the output clock is generated from the SysClk input (via the DDS) by directly applying a frequency tuning word to the DDS. Transfer from normal operation to holdover mode may be accomplished either manually or automatically by appropriately programming the "Automatic Holdover" bit (0=Manual, 1=Auto). The actual transfer to holdover operation, however, depends on the state of the HOLDOVER pin and the state of control register bits "Enable Holdover Override" and "Holdover On/Off ". Manual holdover is established when the “Automatic Holdover” bit is a logic 0 (default). In manual mode, holdover is determined by the state of the HOLDOVER pin (0=Normal, Holdover & Reference Switchover State Machine The interplay between the input reference signals and holdover is most readily demonstrated by means of a state diagram. In Figure 22, the various control signals and the four states are shown. Rev. PrA | Page 36 of 78 Preliminary Technical Data AD9549 Figure 22: Holdover state diagram Abbreviation Key RefA: RefB: HoldOver: FailA: FailB: ValidA: ValidB: Reference A selected Reference B selected Holdover state Reference A failed Reference B failed Reference A validated Reference B validated OvrdRefPin: OvrdHldPin: AutoRefSel: AutoRcov: AutoHold: || & % Override REF SEL pin Override HOLDOVER pin Automatic reference select Automatic holdover recovery Automatic holdover entry Logical OR Logical AND Logical NOT Figure 23: Holdover State Diagram Abbreviation Key States 1 or 2 are in effect when the device is not in the holdover condition, while states 3 & 4 are in effect when the holdover condition is active. When REF A is selected as the "active" reference, then states 1 or 3 are in effect. When REF B is selected as the "active" reference, then states 2 or 4 are in effect. A transition between states depends on the reference switchover and holdover control register settings, the logic state of the REFSELECT and HOLDOVER pins, and the occurrence of certain events (e.g., a reference failure). The state machine and its relationship to control register and external pin stimuli are shown in the diagram below. The state machine generates a "derived" reference selection and holdover state. The actual control signal sent to the reference switchover logic and the holdover logic, however, depends on the control signals applied to the MUXes. The "dashed" path leading to the REFSELECT and HOLDOVER pins is active when the "auto" mode is selected for reference selection and/or holdover assertion. Reference Recovery Timers Each of the two reference inputs has a dedicated recovery timer. The status of these timers is used by the holdover state machine as part of the decision making process for reverting to a previously faulty reference. For example, suppose that a reference fails (i.e., an LOR or OOL condition is in effect) and Rev. PrA | Page 37 of 78 AD9549 that the device is programmed to revert automatically to a valid reference when it recovers. When a reference returns to normal operation, the LOR and OOL conditions will no longer be true. However, the state machine is not immediately notified of the clearing of the LOR and OOL condition. Instead, once both the LOR and OOL conditions are cleared, the recovery timer for that particular reference is started. Expiration of the recovery timer is an indication to the state machine that the reference is now available for selection. However, even though the reference is now flagged as "valid", actual transition to the recovered reference depends on the programmed settings of the various holdover control bits. The recovery timers are controlled via the I/O Register Map. Although there are two independent recovery timers, the programmed information is shared among both. The desired time interval is controlled via a 5-bit word (T) such that 0 ≤ T ≤ 31 (default is T=0). The duration of the recovery timers is given by: Preliminary Technical Data signal with the reference input signal, and will start to adjust the phase/frequency using the holdover signal as its starting point. The behavior of the holdover state machine when it is in automatically exiting holdover mode is very similar. The primary difference is that reference monitor is continuously monitoring both reference inputs and as soon as one becomes valid, it automatically switches to that input. The output frequency in Holdover mode depends on the frequency of the SysClk input source and the value of the frequency tuning word applied to the DDS. Therefore, the stability of the output signal is completely dependent on the stability of the SysClk source (and the SysClk PLL Multiplier, if enabled). Note: It is very important to power down an unused reference input to avoid chattering on that input. Also, the reference validation timer must be set to at least one full cycle of the signal coming out of the reference divider. TRECOVER = T0 2 T +1 − 1 ( ) Where T0 is the sample rate of the digital loop filter, which has a period of: T0 = 2 PIO fS (see the Digital Loop Filter section) A single bit, Disable Recovery Timer, causes the state machine to ignore the status of the recovery timers. Instead, the state machine relies on the user to validate the recovery of the faulty reference and then to set the Validate RefA (or RefB) bit manually in the I/O Register Map. That is, the state machine treats the setting of the "Validate" bits as though the associated timer had expired. Holdover Operation When the holdover condition is asserted, the DDS output frequency is no longer controlled by the phase lock feedback loop. Instead, a static frequency tuning word (FTW) is applied to the DDS to hold it at a specified frequency. The source of the static FTW depends on the status of the appropriate control register bits. During normal operation, the Averager & Sampler monitors and accumulates up to 65000 FTW values as they are generated, and upon entering holdover, the holdover state machine can use the averaged tuning word, or the last valid tuning word. Holdover mode is exited in a similar manner that it is entered. If manual holdover control is used, then when the holdover pin is de-asserted, the phase detector starts comparing the holdover Rev. PrA | Page 38 of 78 Preliminary Technical Data Holdover Sampler and Averager If activated via the I/O Register Map, the HSA continuously monitors the data generated by the digital loop filter in the background. It should be noted that the loop filter data is a time sequence of frequency adjustments (∆f) to the DDS. The output of the HSA is routed to a read-only register in the I/O Register Map and to the holdover control logic. The first of these destinations (the read-only register) serves as a "trace buffer" that may be read by the user and the data processed externally. The second destination (the holdover control logic) uses the output of the HSA to "peg" the DDS at a specific frequency upon entry into the holdover state. Hence, the DDS will assume a frequency specified by the last value generated by the HSA just prior to entering the holdover state. The state of the output MUX is established by programming the I/O Register Map. The default state is such that the ∆f values pass through the HSA unaltered. In this mode, the output sample rate is fS/P, the same as the sample rate of the digital loop filter. NOTE: P is the divide ratio of the "P"-divider (see “Digital Loop Filter” on Page 24) and fS is the DAC sample rate. Alternatively, the MUX can be set to select the averaging path. In this mode, a "block average" is performed on a sequence of samples. The length of the sequence is determined by programming the value of Y (a 4-bit number stored in the I/O Register Map), and has a value of 2Y+1. In the "averaging" mode, the output sample rate is given by fS/ (P∙2Y+1). When the number of ∆f samples specified by Y has been collected, the averaged result is delivered to a 2-stage pipeline. The last stage of the pipeline contains the value that will be delivered to the holdover control logic when a transition into the holdover state occurs. The pipeline is a guarantee that the averaged ∆f value delivered to the holdover control logic has not been interrupted by the transition into the holdover state. The pipeline provides an inherent delay of ∆t = P∙2Y+1/fS. Hence, the DDS "hold" frequency is the average as it appeared ∆t to 2∆t seconds prior to entering the holdover state. Note that the user has some control over the duration of ∆t because it is dependent on the programmed value of Y. REF IN AD9549 between DC and fS/2 (with 48-bit resolution). However, the user is given the option of placing limits on the tuning range of the DDS via two 48-bit registers in the I/O Register Map: FTW Upper Limit and FTW Lower Limit. If the tuning word input exceeds the upper or lower frequency limit boundaries, the tuning word is clipped to the appropriate value. The default setting for these registers is fS/2 and DC, respectively. It may be desirable to limit the output range of the DDS to a narrow band of frequencies (for example, to achieve better jitter performance in conjunction with a band pass filter). See “Use of Narrowband Filter for High Performance” on Page 40 for more information about this feature. REF IN R Phase Detector Loop Filter DDS/DAC S External Reconstruction Filter Low Pass Frequency Limiter R Phase Detector Loop Filter DDS/DAC S External Reconstruction Filter Band Pass Figure 24: Application of the Frequency Limiter RECONSTRUCTION FILTER The origin of the output clock signal produced by the AD9549 is the combined DDS and DAC. The DAC output signal appears as a sinusoid sampled at fS. The frequency of the sinusoid is determined by the frequency tuning word (FTW) that appears at the input to the DDS. The DAC output is typically passed through an external reconstruction filter that serves to remove the artifacts of the sampling process and other spurs outside the filter bandwidth. The signal is then brought back on-chip to be converted to a square wave that is routed internally to the output clock driver or the 2x DLL multiplier. Since the DAC constitutes a sampled system, its output must be filtered so that the analog waveform accurately represents the digital samples supplied to the DAC input. The unfiltered DAC output contains the desired base band signal, which extends from DC to the Nyquist frequency (fS/2). It also contains OUTPUT FREQUENCY RANGE CONTROL Under normal operating conditions, its output frequency is dynamically changing in response to the output of the digital loop filter. The loop filter can steer the DDS to any frequency Rev. PrA | Page 39 of 78 AD9549 images of the base band signal that theoretically extend to infinity. Notice that the odd images (shown in Figure 25 below) are mirror images of the base band signal. Furthermore, the entire DAC output spectrum is affected by a sin(x)/x response, which is caused by the "sample and hold" nature of the DAC output signal. Magnitude (dB) 0 -20 -40 -60 -80 -100 fS/2 base band fS 3fS/2 2fS 5fS/2 spurs Image 0 Image 1 Image 2 Image 3 Image 4 Preliminary Technical Data primary signal filter response sin(x)/x envelope f Figure 25: DAC Spectrum vs. Reconstruction Filter Response The response of the reconstruction filter should preserve the base band signal (image 0), while completely rejecting all other images. However, a practical filter implementation will typically exhibit a relatively flat pass band that covers the desired output frequency plus 20%, roll off as steeply as possible, and then maintain significant (though not complete) rejection of the remaining images. Plot 14: Filtered DAC Output Using 7th order elliptical with Fc=186 MHz. Same Conditions as previous plot. Since the DAC output signal serves as the feedback signal for the digital PLL, the design of the reconstruction filter can have a significant impact on the overall jitter performance. Hence, good filter design and implementation techniques are important for obtaining the best possible jitter results. Use of Narrowband Filter for High Performance A distinct advantage of the AD9549 architecture is its ability to constrain the frequency output range of the DDS. This allows the user to employ a narrow band reconstruction filter instead of the low pass response shown above resulting in less jitter on the output. For example, suppose that the nominal output frequency of the DDS is 150MHz. One might then choose a 5MHz narrow band filter centered at 150MHz. By using the AD9549's DDS frequency limiting feature, the user could constrain the output frequency to 150MHz ± 4.9MHz (which allows for a 100kHz margin at the pass band edges). This will ensure that a feedback signal is always present for the digital PLL. Such a design would be extremely difficult to implement with conventional PLL architectures. Plot 13: DAC Output without Reconstruction Filter. fOUT=155.52 MHz. Sysclk=25 MHz. Sysclk PLL = x40. Spur reduction disabled. DPLL Loop Closed. Freq Span for Plot: 500 MHz. Rev. PrA | Page 40 of 78 Preliminary Technical Data FDBK INPUTS The FDBK pins serve as the input to the feedback path of the digital PLL. Typically, these pins are used to receive the signal generated by the DDS after it has been band-limited by the external reconstruction filter. A diagram of the FDBK input pins is provided here, which includes some of the internal components used to bias the input circuitry. Note that the FDBK input pins are internally biased to a DC level of ~1V. Care should be taken to ensure that any external connections do not disturb the DC bias, as this may significantly degrade performance. FDBK_IN FDBK_INB VSS 15K ~1pF To S-Divider and Clock Output Section AD9549 VDD + 1pF Vb REFA_IN 8K (or REFB_IN) GND ~1pF 8K ~1pF To Reference Monitor and Switching Logic REFA_INB (or REFB_INB) VSS ~1pF 15K Figure 27: Reference Inputs + ~1V ~2pF VSS NOTE: Support for redundant reference clocks is achieved by using the two Reference Clock receivers (REFA & REFB). In order to accommodate a variety of input signal conditions the value of Vb is programmable via a pair of bits in the I/O Register Map. Table 3 below gives the value of Vb for the bit pattern in Register 040F. Reference Bias Level R040F[1:0] 00 (default) 01 10 11 Vb AVDD3-800mV AVDD3-400mV AVDD3-1600mV AVDD3-1200mV Figure 26: Differential FDBK Inputs REFERENCE INPUTS Reference Clock Receiver The Reference Clock receiver is the point at which the user supplies the input clock signal that the Synchronizer will synthesize into an output clock. The clock receiver circuit is able to handle a relatively broad range of input levels as well as frequencies from 8 kHz up to 750 MHz. The following is a diagram of the REFA/B input pins, which includes some of the internal components used to bias the input circuitry. Note that the REF input pins are internally biased by a DC source, Vb. Care should be taken to ensure that any external connections do not disturb the DC bias, as this may significantly degrade performance. Table 3: Setting of Input Bias Voltage (Vb) Rev. PrA | Page 41 of 78 AD9549 SYSCLK INPUTS Functional Description The SysClk pins are where an external timebase is connected to the AD9549 for generating the internal high frequency system clock (fS). The SysClk inputs can be operated in one of three modes: 1) SysClk PLL Bypassed, 2) SysClk PLL Enabled with input signal generated externally, or 3) Crystal Resonator with SysClk PLL Enabled. A functional diagram of the system clock generator is shown below. Preliminary Technical Data frequency as the SysClk input signal, and the magnitude of the sub-harmonic can be quite large. When employing the BED care must be taken to ensure that the loop bandwidth of the SysClk PLL Multiplier will adequately suppress the subharmonic. The benefit offered by the BED depends on the magnitude of the sub-harmonic, the loop bandwidth of the SysClk PLL Multiplier, and the overall phase noise requirements of the specific application. In many applications, the AD9549 clock output is applied to the input of another PLL, and the subharmonic is often suppressed by the relatively narrow bandwidth of the downstream PLL. NOTE: Generally, the benefits of the Bipolar Edge Detector are realized for SysClk input frequencies of 25MHz and above. SysClk PLL Multiplier When the SysClk PLL Multiplier path is employed, the frequency applied to the SysClk input pins must be limited so as not to exceed the maximum input frequency of the SysClk PLL phase detector. A block diagram of the SysClk generator appears in Figure 29 below. Figure 28: System Clock Generator Block Diagram The SysClk PLL multiplier path is enabled by a logic 0 (default) in the PD SysClk PLL location of the I/O Register Map. The SysClk PLL multiplier can be driven from the SysClk input pins by one of two means depending on the logic level applied to the 1.8V CMOS CLKMODESEL pin. When CLKMODESEL=0, a crystal can be connected directly across the SysClk pins. When CLKMODESEL=1, the maintaining amp is disabled, and an external frequency source (oscillator, signal generator, etc.) can be connected directly to the SysClk input pins. Note that CLKMODESEL=1 does not disable the system clock PLL. When the SysClk PLL multiplier path is disabled, the AD9549 must be driven by a high frequency signal source (up to 1GHz). The signal thus applied to the SysClk input pins becomes the internal DAC sampling clock (fS) after passing through an internal buffer. Figure 29: Block Diagram of the SysClk PLL Bipolar Edge Detector The SysClk PLL Multiplier path offers an optional Bipolar Edge Detector (BED). This block acts as a frequency doubler by generating a pulse on each edge of the SysClk input signal. The SysClk PLL Multiplier locks to the falling edges of this regenerated signal. The impetus for doubling the frequency at the input of the SysClk PLL Multiplier is that an improvement in overall phase noise performance can sometimes be realized. The main drawback is that the BED output not a rectangular pulse with a constant duty cycle even for a perfectly symmetric SysClk input signal. This results in a sub-harmonic appearing at the same The SysClk PLL Multiplier has a 1GHz VCO at its core. A phase/frequency detector (PFD) and charge pump provide the steering signal to the VCO in typical PLL fashion. The PFD operates on the falling edge transitions of the input signal, which means that the loop locks on the negative edges of the reference signal. The charge pump gain is controlled via the I/O Register Map by selecting one of three possible constant current sources ranging from 125-375µA in 125µA steps. The center frequency of the VCO is also adjustable via the I/O Register Map and provides high/low gain selection. The feedback path from VCO to PFD consists of a fixed divide-by-2 prescaler followed by a programmable divide-by-N block, where 2 ≤ N ≤ 33. This limits the overall divider range to any even integer from 4 to 66, inclusive. The value of N is Rev. PrA | Page 42 of 78 Preliminary Technical Data programmed via the I/O Register Map via a 5-bit word that spans a range of 0 to 31, but the internal logic automatically adds a bias of 2 to the value entered, extending the range to 33. Care should be taken when choosing these values so as to not exceed the maximum input frequency of the Sysclk PLL phase detector or bipolar edge detector. These values can be found in the AC Electrical Characteristics section of this datasheet. Sysclk Multiplier K1 0 1 KLO K K0 K1 216 KHI Figure 34: Frequency Estimator ε vs. K An iterative technique is necessary to determine the exact values of K0 and K1. However, a closed form exists for a conservative estimate of K0 (KLO) and K1 (KHI): K LO = ceil K HI [ (1 + )] = ceil [ (1 + )] ρ 1 ε0 1 1 ρ 2 ε0 AD9549 As an example, consider the system conditions specified below: fS = 400MHz R=8 fREF_IN = 155.52MHz ε0=0.00005 (i.e., 50ppm) Preliminary Technical Data obtained. The result is the value of K1. For the above example, K1=1912, Tmeas=98.35µs, and ε=39.8ppm. If a further reduction of the measurement time is necessary, then K0 can be used. K0 is found in a manner similar to K1. Start with K=KLO and increment K successively while evaluating the inequality for each value of K. Stop the process the first time that the inequality is satisfied. The result is the value of K0. For the above example, K0=1005, Tmeas=51.70µs and ε=49.0ppm. These conditions yield KMAX=3185, which is the largest K value that can be programmed without causing the frequency estimator counter to overflow. With K=KMAX we find that Tmeas=163.84µs and ε=30.2ppm. KMAX will generally (but not always) yield the smallest value of ε, but this comes at the cost of the largest measurement time (Tmeas). If the measurement time must be reduced, then KHI can be used instead of KMAX. This yields: KHI=1945, Tmeas=100.05µs, and ε=39.4ppm. The measurement time can be further reduced (though marginally) by using K1 instead of KHI. K1 is found by solving the ε ≤ ε0 inequality iteratively. To do so, start with K=KHI and decrement K successively while evaluating the inequality for each value of K. Stop the process the first time that the inequality is no longer satisfied and add 1 to the value of K thus STATUS AND WARNINGS Status Pins Four pins (S1 – S4) are reserved for providing device status information to the external environment. These four pins are individually programmable (via the serial I/O port) as an OR'd combination of six possible status indications. Each pin has a dedicated group of control register bits that determine which internal status flags are used to provide an indication on a particular pin (as shown in the diagram below). Internal Status Flags RefA LOR RefA OOL RefA Invalid RefB LOR RefB OOL RefB Invalid Phase Lock Detect 0 1 0 1 0 1 Ref Invalid Phase Lock Freq. Lock Frequency Lock Detect Ref OOL Ref LOR Status Pin (1 of 4) IRQ RefAB LOR RefAB OOL RefAB Invalid RefAB Phase Lock Frequency Lock IRQ IRQ Status Pin Control Register (1 of 4) Figure 35: Status Pin Control Rev. PrA | Page 48 of 78 Preliminary Technical Data Reference Monitor Status In the case of reference monitoring status information, a pin can be programmed for either RefA or RefB, but not both. In addition, the OR'd output configuration allows the user to combine multiple status flags into a single status indication. For example, if both the LOR and OOL control register bits are true, then the status pin associated with that particular control register will give an indication if either the LOR or OOL status flag is asserted for the selected reference (A or B). AD9549 Status Pin S4 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 S3 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 S2 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 S1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 SysClk Input Mode Xtal/PLL Xtal /PLL Xtal /PLL Xtal /PLL Xtal /PLL Xtal /PLL Xtal /PLL Xtal /PLL Direct Direct Direct Direct Direct Direct Direct Direct Output Frequency in MHz 0 38.87939 51.83411 61.43188 77.75879 92.14783 122.87903 155.51758 0 38.87939 51.83411 61.43188 77.75879 92.14783 122.87903 155.51758 Default DDS Output Frequency on Power-Up The four Status Pins (S1-S4) provide a completely separate function at power-up. They can be used to define the output frequency of the DDS at power-up even though the I/O Registers have not yet been programmed. This is made possible because the status pins are designed with bi-directional drivers. At power-up, internal logic initiates a reset pulse of about 10 ns. During this time, S1-S4 briefly function as input pins, and can be driven externally. Any logic levels thus applied are transferred to a 4-bit register on the falling edge of the internally initiated pulse. The falling edge of the pulse also returns S1-S4 to their normal function as output pins. The same behavior occurs when the RESET pin is asserted manually. Setting up S1-S4 for default DDS start-up is accomplished by connecting a resistor to each pin (either pull-up or pull-down) to produce the desired bit pattern, yielding 16 possible states that are used both to address an internal 8x16 ROM and to select the SysClk Mode (see Table 5). The ROM contains eight 16-bit DDS frequency tuning words (FTWs), one of which is selected by the state of the S1-S3 pins. The selected FTW is transferred to the FTW0 register in the I/O Register Map without the need for an "I/O_Update". This ensures that the DDS generates the selected frequency even if the I/O registers have not been programmed. The state of the S4 pin selects whether the internal System Clock is generated by means of the internal SysClk PLL multiplier or not (see the SysClk Input section for details). The DDS output frequency listed in Table 5 assumes that the internal DAC sampling frequency (fS) is 1GHz. These frequencies scale 1:1 with fS, meaning that other startup frequencies are available by varying the Sysclk frequency. At startup, the internal frequency multiplier defaults to 40x when the Xtal/PLL Mode is selected via the Status Pins. Note: when using this mode, the digital PLL loop is still open, and the AD9549 is acting as a frequency synthesizer. The frequency dividers and DPLL loop filter must still be programmed prior to closing the loop. Table 5: Default Power-up Frequency Options for 1 GHz System Clock Interrupt Request (IRQ) Any one of the four status pins (S1-S4) may be programmed as an IRQ pin. If a status pin is programmed as an IRQ pin, then the state of the internal IRQ flag appears on that pin. An IRQ flag is internally generated based on the change of state of any one of the internal status flags. The individual status flags are routed to a read-only I/O register (Status Register) so that the user may interrogate the status of any of these flags at any time. Furthermore, each status flag is monitored for a change in state. In some cases, only a change of state in one direction is necessary (e.g., the Frequency Estimate Done flag), but in most Rev. PrA | Page 49 of 78 AD9549 cases, the status flags are monitored for a change of state in either direction (see the diagram below). Whether or not a particular state change is allowed to generate an IRQ is dependent on the state of the bits in the IRQ Mask Register. The user programs the mask to enable those events, which are to constitute cause for an IRQ. If an unmasked event occurs, it will trigger the IRQ latch and the IRQ Flag will be asserted (active high). The state of the IRQ Flag is made available externally via one of the programmable status pins (see the Status Pins section of this document). The automatic assertion of the IRQ Flag causes the contents of the Status Register to be transferred to the IRQ Register. The Preliminary Technical Data user can then read the IRQ Register any time after the indication of an IRQ event (i.e., assertion of the IRQ Flag). By noting the bits in the IRQ Register that is set, the cause of the IRQ event can be determined. Once the IRQ Register has been read, the user must set the IRQ Reset bit in the appropriate control register via the serial I/O port. This restores the IRQ Flag to its default state, clears the IRQ status register, and resets the edge detection logic that monitors the status flags in preparation for the next state change. IRQ Mask Register Status Flags Edge Detect Edge Detect Edge Detect Edge Detect Edge Detect Edge Detect Edge Detect Edge Detect Edge Detect Edge Detect Edge Detect IRQ Reg. Status Register IRQ Reset Figure 36: Interrupt Request Logic Rev. PrA | Page 50 of 78 Preliminary Technical Data POWER-ON RESET On initial power-up, the AD9549 internally generates a 75ns RESET pulse. The pulse is initiated when both of the following two conditions are met: The 3.3v supply is greater than 2.35± 0.1V The 1.8v supply is greater than 1.4± 0.05V Less than 1 ns after RESET goes high, the S1-S4 configuration pins go high impedance, and remain high impedance until RESET is deactivated. This allows strapping and configuration during RESET. Because of this reset sequence, power supply sequencing isn’t critical. AD9549 The following sequence should be followed when changing frequencies the AD9549: 1. 2. 3. 4. Open the loop and enter single tone mode via Register 0100. Enter the new register settings. Write 1E to Register 0012. Once the registered are loaded, the OOL (Out of limits) and LOR (loss of reference) can be monitored to insure that a valid reference signal is present on RefA or RefB. If a valid reference is present, Register 0100 can be reprogrammed to clear Single Tone Mode and lock the loop. Automatic Holdover mode can now be used to make the AD9549 immune to any disturbance on the reference inputs. 5. AD9549 POWER UP AND PROGRAMMING SEQUENCE The following sequence should be followed when initializing the AD9549: 1. 2. Apply Power. The AD9549 will perform an internal reset. IMPORTANT: Make sure the desired configuration registers have Single Tone mode(R0100[5]) set, and Lock Loop (R0100[0]) cleared. If the Lock Loop bit is set on initial loading, the AD9549 will attempt to lock the loop before it has been configured. Once the registered are loaded, the OOL (Out of limits) and LOR (loss of reference) can be monitored to insure that a valid reference signal is present on RefA or RefB. If a valid reference is present, Register 0100 can be reprogrammed to clear Single Tone Mode and lock the loop. Automatic Holdover mode can now be used to make the AD9549 immune to any disturbance on the reference inputs. 6. Notes: Attempting to lock the loop without a valid reference can put the AD9549 into a state that requires a reset. Automatic Holdover mode is not available unless the loop has been successfully closed. If the user desires to open and close the loop manually, we recommend writing 1E to Register 0012 prior to reclosing the loop. 3. 4. 5. Rev. PrA Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2007 Analog Devices, Inc. All rights reserved. AD9549 POWER MANAGEMENT The AD9549 features multiple power supplies, and their power consumption varies with its configuration. This section covers which power supplies can be grouped together, and how each block’s power consumption varies with frequency. The numbers quoted here are for comparison only. Please refer to the spec table for exact numbers. With each group, bypass caps of 1 uF in parallel with a 10 uF should be used. The recommendations here are for typical applications, and an application demanding the highest performance may require additional power supply isolation. Preliminary Technical Data minimum, a ferrite bead should be used for isolation, with a separate regulator being ideal. 3.3V SUPPLIES Digital I/O (Pin 1) and VDDX_REF (Pin 14): These two 3.3V supplies can be grouped together. The power consumption on Pin 1 varies dynamically with serial port activity. Noise from the serial port that couples into the reference input should be filtered by the digital PLL. AVDD3 (Pin 37): This is the CMOS driver supply. If the CMOS driver will be used, this supply should be isolated from other 3.3V supplies to avoid a spur at the output frequency. The power consumption is a function of the output frequency and loading of this pin. If this supply will not be used, this supply can be tied to other 3.3V supplies, and its consumption will be less than 5 mA. AVDD3 (Pins 46,47,49): These are 3.3V DAC power supplies that typically consume about 25mA. At a minimum, a ferrite bead should be used to isolate these from other 3.3V supplies, with a separate regulator being ideal. 1.8V SUPPLIES Digital Core (Pins 3,5,7): These Pins can be grouped together. Their current consumption increases from about 160mA at a system clock of 700 MHz to about 220mA a system clock of 1 GHz. There is also a slight (~5%) increase as Fout increases from 50 MHz to 400 MHz. VDD DAC Decoder (Pin 53): This 1.8V supply consumes about 20 to 40 mA. It is critical that this supply be well isolated from other 1.8V supplies. At a minimum, a ferrite bead should be used for isolation, with a separate regulator being ideal. AVDD (Pins 11, 19, 23, 24, 36, 42, 45): These pins may be grouped together and should be isolated from other 1.8V supplies. At a minimum, a ferrite bead should be used for isolation, with a separate regulator being ideal. AVDD (Pin 25, 26, 29, 30): These pins may be grouped together and should be isolated from other 1.8V supplies. At a Rev. PrA | Page 52 of 78 Preliminary Technical Data SERIAL CONTROL PORT The AD9549 serial control port is a flexible, synchronous, serial communications port that allows an easy interface with many industry-standard microcontrollers and microprocessors. Single or multiple byte transfers are supported, as well as MSB first or LSB first transfer formats. The AD9549 serial control port can be configured for a single bidirectional I/O pin (SDIO only) or for two unidirectional I/O pins (SDIO/SDO). AD9549 OPERATION OF SERIAL CONTROL PORT Framing a Communication Cycle with CSB A communications cycle (a write or a read operation) is gated by the CSB line. CSB must be brought low to initiate a communication cycle. CSB stall high is supported in modes where three or fewer bytes of data (plus instruction data) are transferred (W1:W0 must be set to 00, 01, or 10, see Table 6 below). In these modes, CSB can temporarily return high on any byte boundary, allowing time for the system controller to process the next byte. CSB can go high on byte boundaries only and can go high during either part (instruction or data) of the transfer. During this period, the serial control port state machine enters a wait state until all data has been sent. If the system controller decides to abort the transfer before all of the data is sent, the state machine must be reset by either completing the remaining transfer or by returning the CSB low for at least one complete SCLK cycle (but less than eight SCLK cycles). Raising the CSB on a non-byte boundary terminates the serial transfer and flushes the buffer. In the streaming mode (W1:W0 = 11b), any number of data bytes can be transferred in a continuous stream. The register address is automatically incremented or decremented (see the MSB/LSB First Transfers section). CSB must be raised at the end of the last byte to be transferred, thereby ending the stream mode. SERIAL CONTROL PORT PIN DESCRIPTIONS SCLK (serial clock) is the serial shift clock. This pin is an input. SCLK is used to synchronize serial control port reads and writes. Write data bits are registered on the rising edge of this clock, and read data bits are registered on the falling edge. This pin is internally pulled down by a 30 kΩ resistor to ground. SDIO (serial data input/output) is a dual-purpose pin and acts as input only or input/output. The AD9549 defaults to bidirectional pins for I/O. Alternatively, SDIO can be used as a unidirectional I/O pin by writing to the SDO active register at 00h = 1b. In this case, SDIO is the input, and SDO is the output. SDO (serial data out) is used only in the unidirectional I/O mode (00h = 1) as a separate output pin for reading back data. Bidirectional I/O mode (using SDIO as both input and output) is active by default and (i.e. SDO enable register at 00h = 0). CSB (chip select bar) is an active low control that gates the read and write cycles. When CSB is high, SDO and SDIO are in a high impedance state. This pin is internally pulled up by a 100 kΩ resistor to 3.3V. It should not be left floating. See the Operation of Serial Control Port section on the use of the CSB in a communication cycle. Communication Cycle—Instruction Plus Data There are two parts to a communication cycle with the AD9549. The first writes a 16-bit instruction word into the AD9549, coincident with the first 16 SCLK rising edges. The instruction word provides the AD9549 serial control port with information regarding the data transfer, which is the second part of the communication cycle. The instruction word defines whether the upcoming data transfer is a read or a write, the number of bytes in the data transfer, and the starting register address for the first byte of the data transfer. SCLK (PIN 64) SDIO (PIN 63) SDO (PIN 62) CSB (PIN 61) Write AD9549 SERIAL CONTROL PORT Figure 37: Serial Control Port If the instruction word is for a write operation (I15 = 0b), the second part is the transfer of data into the serial control port buffer of the AD9549. The length of the transfer (1, 2, 3 bytes, or streaming mode) is indicated by 2 bits (W1:W0) in the instruction byte. The length of the transfer indicated by (W1:W0) does not include the two-byte instruction. CSB can be raised after each sequence of 8 bits to stall the bus (except after the last byte, where it ends the cycle). When the bus is stalled, the serial transfer resumes when CSB is lowered. Stalling on non-byte boundaries resets the serial control port. Rev. PrA | Page 53 of 78 AD9549 There are three types of registers on the AD9549: buffered, live, and read-only. Buffered (also referred to as mirrored) registers require an IO_UPDATE to transfer the new values from a temporary buffer on the chip to the actual register, and are marked with an “M” in the column labeled “Type” of the register map. Toggling the IO_UPDATE pin or writing a “1” to the Register Update bit (R05h) will cause the update to occur. Since any number of bytes of data can be changed before issuing an update command, the update simultaneously enables all register changes since any previous update. Live registers do not require IO_UPDATE and update immediately after being written. Read-only registers ignore write commands, and are marked “RO” in the “Type” column of the register map. The “Type” column of the register map may also have an “AC,” which indicates that the register is auto-clearing. Preliminary Technical Data instruction mode on power-up, and the 8-bit instruction mode is not supported. THE INSTRUCTION WORD (16 BITS) The MSB of the instruction word is R/W, which indicates whether the instruction is a read or a write. The next two bits, W1:W0, indicate the length of the transfer in bytes. The final 13 bits are the address (A12:A0) at which to begin the read or write operation. For a write, the instruction word is followed by the number of bytes of data indicated by Bits W1:W0, which is interpreted according to Table 6. A12:A0: These 13 bits select the address within the register map that is written to or read from during the data transfer portion of the communications cycle. The AD9549 uses all of the 13-bit address space. For multi-byte transfers, this address is the starting byte address. Read If the instruction word is for a read operation (I15 = 1b), the next N × 8 SCLK cycles clock out the data from the address specified in the instruction word, where N is 1,2,3,4 as determined by W1:W0. In this case, 4 is used for streaming mode where 4 or more words are transferred per read. The data read back is valid on the falling edge of SCLK. The default mode of the AD9549 serial control port is bidirectional mode, and the data read back appears on the SDIO pin. It is possible to set the AD9549 to unidirectional mode by writing the SDO enable register at 00h = 0b, and in that mode, the requested data appears on the SDO pin. By default, a read request reads the register value that is currently in use by the AD9549. However, setting R04h=1 will cause the “buffered” registers to be read instead. The buffered registers are the ones that will take effect during the next IO_UPDATE. W1 0 0 1 1 W0 0 1 0 1 Bytes to Transfer (excluding the two-byte instruction) 1 2 3 Streaming Mode Table 6: Byte Transfer Count MSB/LSB FIRST TRANSFERS CONTROL REGISTERS REGISTER BUFFERS SCLK SDIO SDO CSB SERIAL CONTROL PORT UPDATE REGISTERS toggle IO_UPDATE pin AD9549 CORE The AD9549 instruction word and byte data may be MSB first or LSB first. The default for the AD9549 is MSB first. The LSB first mode may be set by writing 1b to Register 00h, and requires that an I/O Update be executed. Immediately after the LSB, first bit is set, all serial control port operations are changed to LSB first order. When MSB first mode is active, the instruction and data bytes must be written from MSB to LSB. Multi-byte data transfers in MSB first format start with an instruction byte that includes the register address of the most significant data byte. Subsequent data bytes must follow in order from high address to low address. In MSB first mode, the serial control port internal address generator decrements for each data byte of the multibyte transfer cycle. Figure 38: Relationship Between Serial Control Port Register Buffers and Control Registers of the AD9549 The AD9549 uses Addresses 00h to 509h. Although the AD9549 serial control port allows both 8-bit and 16-bit instructions, the 8-bit instruction mode provides access to five address bits (A4 to A0) only, which restricts its use to the address space 00h to 01F. The AD9549 defaults to 16-bit Rev. PrA | Page 54 of 78 Preliminary Technical Data When LSB_First = 1b (LSB first), the instruction and data bytes must be written from LSB to MSB. Multi-byte data transfers in LSB first format start with an instruction byte that includes the register address of the least significant data byte followed by multiple data bytes. The serial control port internal byte address generator increments for each byte of the multi-byte transfer cycle. The AD9549 serial control port register address decrements from the register address just written toward 0000h for multibyte I/O operations if the MSB first mode is active (default). If MSB I15 R/W I14 W1 I13 W0 I12 A12 I11 A11 I10 A10 I9 A9 I8 A8 I7 A7 I6 A6 I5 A5 I4 A4 I3 A3 I2 A2 I1 A1 AD9549 the LSB first mode is active, the serial control port register address increments from the address just written toward 1FFFh for multi-byte I/O operations. Unused addresses are not skipped during multi-byte I/O operations. The user should write the default value to a reserved register, and should only write zeros to unmapped registers. Note: It is more efficient to issue a new write command than writing the default value to more than two consecutive reserved (or unmapped) registers. LSB I0 A0 Table 7: Serial Control Port, 16-Bit Instruction Word, MSB First CSB SCLK DON'T CARE SDIO DON'T CARE R/W W1 W0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 DON'T CARE DON'T CARE 16-BIT INSTRUCTION HEADER REGISTER (N) DATA REGISTER (N – 1) DATA Figure 39: Serial Control Port Write—MSB First, 16-Bit Instruction, 2 Bytes Data CSB SCLK DON'T CARE SDIO R/W W1 W0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 DON'T CARE 16-BIT INSTRUCTION HEADER REGISTER (N) DATA REGISTER (N – 1) DATA REGISTER (N – 2) DATA REGISTER (N – 3) DATA DON'T CARE Figure 40: Serial Control Port Read—MSB First, 16-Bit Instruction, 4 Bytes Data Rev. PrA | Page 55 of 78 05046-020 SDO DON'T CARE 05046-019 AD9549 tDS tS CSB Preliminary Technical Data tHI tDH tLO tCLK tH SCLK DON'T CARE DON'T CARE SDIO Figure 41: Serial Control Port Write: MSB First, 16-Bit Instruction, Timing Measurements CSB SCLK 05046-022 tDV SDIO SDO DATA BIT N DATA BIT N– 1 Figure 42: Timing Diagram for Serial Control Port Register Read CSB SCLK DON'T CARE SDIO DON'T CARE A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 W0 W1 R/W D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 DON'T CARE DON'T CARE 05046-023 16-BIT INSTRUCTION HEADER REGISTER (N) DATA REGISTER (N + 1) DATA Figure 43: Serial Control Port Write—LSB First, 16-Bit Instruction, 2 Bytes Data tS CSB tH tCLK tHI SCLK tLO tDS tDH SDIO BI N BI N + 1 05046-040 Figure 44: Serial Control Port Timing—Write Parameter Description Rev. PrA | Page 56 of 78 05046-021 DON'T CARE R/W W1 W0 A12 A11 A10 A9 A8 A7 A6 A5 D4 D3 D2 D1 D0 DON'T CARE Preliminary Technical Data tDS tDH tCLK tS tH tHI tLO Setup time between data and rising edge of SCLK Hold time between data and rising edge of SCLK Period of the clock Setup time between CSB and SCLK Hold time between CSB and SCLK Minimum period that SCLK should be in a logic high state Minimum period that SCLK should be in a logic low state Table 8: Definitions of Terms Used Serial Control Port Timing Diagrams AD9549 Rev. PrA | Page 57 of 78 AD9549 I/O REGISTER MAP Table 9 Addr (hex) 0000 0000 0001 0002 0003 0004 0005 0010 0010 0011 0012 0013 0020 0020 0021 0022 0023 0100 0100 0101 R Divider [15:0] 0102 0103 R-Divider Falling Edge Triggered Rev. PrA | Page 58 of 78 Preliminary Technical Data Type 1 Name (short description) D7 D6 D5 D4 D3 D2 D1 D0 Default (hex) Serial Port Configuration and Part Identification Serial Config Reserved RO Part ID RO Read Buffer Reg Register Update Power Down and Reset Power Down / Enable Reserved M, AC Reset M History Reset PD Fund DDS IRQ Reset FPFD Reset CPFD Reset S Div2 Reset System Clock N-Divider Reserved PLL Parameters PFD Divider DPLL M PLL Control Single Tone Mode Disable Freq. Estimator Enable Freq Slew Limiter Loop Polarity Close Loop 30 00 00 R Divider /2 00 VCO Auto Range 2x Reference VCO Range Charge Pump Current [1:0] N Divider [4:0] 12 00 04 05 LF Reset R Div2 Reset CCI Reset S Div Reset DDS Reset R Div Reset PD HSTL Driver Enable CMOS Driver Enable Output Doubler PD SysClk PLL PD RefA PD RefB Full PD Digital PD 00 00 00 00 Part ID 09 00 00 SDO Active LSB First (buffered) Soft RST Long Inst. 18 00 02 Serial Options AC PFD Divider [3:0] (relationship between SysClk and PFD clock) Preliminary Technical Data 0104 S Divider [15:0] 0105 0106 0107 0108 0109 010A 010B 010C 010D 010E 010F 0110 0111 0112 0113 0114 0115 0116 0117 0118 0119 011A RO RO RO RO RO RO M M M M M M M M M M M Loop Coefficient s Gamma-0 [7:0] Gamma-0 [11:8] Gamma-1 [2:0] Beta-0 [7:0] Beta-0 [11:8] Beta-1 [2:0] P-Divider Alpha-0 [7:0] Alpha-0 [11:8] Alpha-1 [4:0] Alpha-2 [2:0] S-Divider Falling Edge Triggered P Divider[4:0] AD9549 00 00 S Divider /2 00 05 00 00 00 00 00 00 00 00 00 00 00 00 00 N/A N/A N/A N/A N/A N/A FTW Estimate FTW Estimate [47:0] (read-only) Rev. PrA | Page 59 of 78 AD9549 011B 011C 011D 011E 011F 0120 0121 0122 0123 0124 0125 0126 0127 0128 0129 012A 012B 012C 012D 012E Reserved 012F 0130 M M M FTW Lower Limit [47:0] M M M FTW Limits M M M FTW Upper Limit [47:0] M M M M M M Slew Limit M M M Frequency Slew Limit [47:0] Preliminary Technical Data 00 00 00 00 00 00 FF FF FF FF FF 7F 00 00 00 00 00 00 00 00 00 00 Rev. PrA | Page 60 of 78 Preliminary Technical Data 01A0 01A0 01A1 01A2 Reserved 01A3 01A4 01A5 01A6 01A7 01A8 01A9 01AA 01AB 01AC01AD 01C0 01C0 01C1 01C2 01C3 01C4 M, AC M M Automatic Control Override Averaging Window Reference Validation Ref Validation (continued) Disable Recovery Timer M M M M M M M Phase (Open Loop Only) DDS Phase Word [15:0] Reference Selector / Holdover Holdover Mode Enable Line-Card Mode Enable Ref Input Override Automatic Selector Ref_AB Automatic Recover Enable Holdover Override FTW0 (Open Loop Frequency Tuning Word) Free-Run Mode AD9549 00 00 00 00 00 00 00 00 00 FTW0 [47:0] 00 start-up cond. start-up cond. 00 Automatic Holdover Holdover On/Off 00 00 00 00 FTW Windowed Average Size [3:0] Recovery Timer [4:0] Validate RefA * Validate RefB * 00 * R01C4 is not auto-clear, and should be cleared immediately after setting. R01C4 is auto clear for both validate bits. 0200 0200 0201 HSTL Driver CMOS Driver Rev. PrA | Page 61 of 78 Doubler and Output Drivers OPOL (polarity) HSTL Output Doubler CMOS MUX 05 00 AD9549 0300 0300 0301 0302 0303 0304 0305 IRQ Mask 0306 0307 0308 0309 030A 030B 030C 030E 030F 0310 0311 0312 0313 0314 0315 0316 0317 0318 RO RO RO HFTW RO RO RO M M S1 Pin Config S2 Pin Config S3 Pin Config S4 Pin Config Control Ref? Ref? Ref? Ref? Enable RefA LOR Ref? LOR Ref? LOR Ref? LOR Ref? LOR Enable RefA OOL RefA Valid RefB Valid Ref? OOL Ref? OOL Ref? OOL Ref? OOL Enable RefB LOR Freq Est Done !RefA Valid !RefB Valid Ref? Not Valid Ref? Not Valid Ref? Not Valid Ref? Not Valid Enable RefB OOL Phase Unlock RefA LOR RefB LOR Phase Lock Phase Lock Phase Lock Phase Lock RO Status RO RO IRQ Status RO PFD Freq too High RefA Valid PFD Freq too High RefA Valid PFD Freq too Low RefA LOR PFD Freq too Low RefA LOR Monitor Freq. Est. Done RefA OOL Freq. Est. Done RefA OOL Ref Selected Ref Selected Preliminary Technical Data Free Run RefB Valid Free Run RefB Valid Ref. Changed Phase Lock !RefA LOR !RefB LOR Freq. Lock Freq. Lock Freq. Lock Freq. Lock Ph. Lock Detected RefB LOR Ph. Lock Detected RefB LOR Leave Free Run Freq. Unlock RefA OOL RefB OOL Freq. Lock Detected RefB OOL Freq. Lock Detected RefB OOL Enter Free Run Freq. Lock !RefA OOL !RefB OOL IRQ IRQ IRQ IRQ N/A N/A 00 00 00 00 00 00 60 E0 08 01 A2 N/A N/A Enable Phase Lock Det. Enable Freq. Lock Detector Average or Instantaneous FTW [47:0] (read-only) (An IO_UPDATE is required to refresh these registers.) N/A N/A N/A N/A FF 00 Phase Lock Threshold [31:0] M M M Phase Unlock Watchdog Timer [2:0] Rev. PrA | Page 62 of 78 Phase Lock 00 00 Phase Lock Watchdog Timer [4:0] FF Preliminary Technical Data 0319 031A 031B 031C 031D 031E 031F 0320 0321 0322 0323 0324 0325 0326 0327 0328 0329 032A 032B 032C 032D 032E 032F 0330 0331 M M M M M M RefA LOR Divider [15:0] M M M M M M M RefA OOL Upper Limit [31:0] M M M M RefA OOL Lower Limit [31:0] M M M RefB OOL Divider [15:0] M M M RefB OOL Upper Limit [31:0] M M Rev. PrA | Page 63 of 78 AD9549 00 00 Frequency Lock Frequency Lock Threshold [31:0] 00 00 Frequency Unlock Watchdog Timer [2:0] Frequency Lock Watchdog Timer [4:0] FF FF FF FF RefB LOR Divider [15:0] FF Loss of Reference Reference Out Of Limits 00 RefA OOL Divider [15:0] 00 FF FF FF FF 00 00 00 00 00 00 FF FF FF FF AD9549 0332 0333 0334 0335 0400 0400 K Divider 0401 0402 0403 0404 0405 0406 Reserved 0407 0408 0409 040A 040B 040C 040D 040E 040F 0410 M PFD Offset M DPLL Phase Offset [7:0] M CPFD Gain M FPFD Gain K Divider [15:0] M M Preliminary Technical Data 00 00 RefB OOL Lower Limit [31:0] 00 00 Calibration (User Accessible Trim) 00 00 CPFD Gain Scale [2:0] CPFD Gain [5:0] FPFD Gain [7:0] 00 20 C8 00 00 00 00 00 00 FF DAC Full-scale Current [9:8] 01 00 10 DC Input Level [1:0] 00 00 M M DPLL Phase Offset [13:8] DAC Full-scale Current [7:0] DAC FS Current Reserved Reserved Ref Bias Level Reserved Rev. PrA | Page 64 of 78 Preliminary Technical Data AD9549 0500 0500 0501 0502 0503 0504 0505 0506 0507 0508 0509 M M M M M M M M M M Spur B HSR-B Enable Gain Spur A HSR-A Enable Gain Harmonic Spur Reduction Spur A Harmonic [3:0] Spur A Magnitude [7:0] 00 00 00 Spur A Phase [7:0] Spur A Phase [8] Spur B Harmonic [3:0] Spur B Magnitude [7:0] 00 00 00 00 00 Spur B Phase [7:0] Spur B Phase [8] 00 00 1 Types of Registers: M: Mirrored (also called Buffered). This type of register needs an IO_UPDATE for the new value to take effect.) RO: Read-Only AC: Auto-clear Rev. PrA | Page 65 of 78 AD9549 I/O REGISTER DESCRIPTION Serial Port Configuration (0000 – 0005) 0000; Serial Configuration; bits D4 – D7 are mirror image of D0 – D3 Preliminary Technical Data [0] SDO Active: Enables SDO pin 1=SDO pin enabled (four-wire serial port mode.) 0= three-wire mode. [1] LSB First: Sets bit order for serial port. 1=LSB first. 0=MSB first. IO_UPDATE must occur in order to take effect. [2] Soft Reset: Resets register map except for register 0000. Setting this bit forces a soft reset, meaning that S1-S4 are not tristated, nor is their state read when this bit is cleared. The 9549 will assume the values of S1-S4 that were present during the last hard reset. This bit is not self-clearing, and all other registers will be restored to their default values after a soft reset. [3] Long Instruction: Read-only: this part only supports long instructions. 0001; Reserved 0002 - 0003; Part ID (read-only) 0004; Serial Options [0] Read Buffer Register: For buffered registers, serial port read-back reads from actual (active) registers instead of the buffer. 1= Reads the buffered values that will take effect during the next IO_UPDATE. 0= Reads values that are currently in effect. 0005; Serial Options; Self Clearing [0] Register Update: Software access to the “Register Update” pin function. Writing a “1” to this bit is identical to performing an IO_UPDATE. Power Down and Reset 0010; Power Down and Enables; Power up default is defined by start-up pins. [0] Digital PD; Remove clock from most of digital section; leave serial port usable. In contrast to Full PD, setting this bit does not de-bias inputs, allowing for quick wake-up. [1] Full PD; Setting this bit is identical to activating the PD pin, and puts all blocks (except serial port) into power down mode. Sysclk is turned off. [2] PD RefB; Power down reference clock B input (and related circuits) [3] PD RefA; Power down reference clock A input (and related circuits) [4] PD System Clock PLL: System clock multiplier is powered down. 1= System Clock Multiplier powered down. [5] Enable Output Doubler; Power up output clock generator doubler. Output Doubler must still be enabled in Register 0200. [6] Enable CMOS Driver: Power up CMOS output driver. 1= CMOS Driver on. [7] PD HSTL Driver: Power down HSTL output driver. 1 = HSTL Driver powered down. 0011; Reserved Rev. PrA | Page 66 of 78 Preliminary Technical Data 0012; Reset; Auto Clear; To reset the entire chip, the user may also use the (non-self clearing) Soft Reset bit in Register 0000. Except for IRQ reset, the user normally would not need to use these. [0] DDS (Direct Digital Synthesis) Reset [1] CCI (Cascaded Comb Integrator) Reset [2] LF (Loop Filter) Reset [3] CPFD (Coarse Phase Frequency Detector) Reset [4] FPFD (Fine Phase Frequency Detector) Reset [5] IRQ Reset: Clear IRQ signal and IRQ status monitor [6] Unused [7] History Reset: Setting this bit clears the FTW monitor and pipeline. 0013; Reset (continued); NOT Auto Clear. [0] R Divider Reset: Synchronous (to R divider prescaler output) reset for integer divider [1] S Divider Reset: Synchronous (to S divider prescaler output) reset for integer divider [2] R Div2 Reset: Asynchronous reset for R prescaler [3] S Div2 Reset: Asynchronous reset for S prescalar AD9549 [7] PD Fund DDS: Setting this bit powers down the DDS fundamental output, but not the spurs. It is used during tuning of the Spur Killer circuit. System Clock 0020; N Divider [4:0] N Divider: These bits set the Feedback divider for System Clock PLL. There is a fixed /2 preceding this block, as well as a an offset of 2 added to this value. Therefore, setting this register to 00000 translates to an overall feedback divider ratio of 4. See Figure 29: Block Diagram of the SysClk PLL on Page 42. 0021; Reserved 0022; PLL Parameters [1:0] Charge Pump Current: 00: 250 uA , 01: 375 uA, 10: Off, 11: 125 uA [2] VCO Range: Select low range or high range VCO. 0= low range (700 to 800 MHz). 1= high range (850 to 1000 MHz). For System clock settings in between 800-850 MHz, use the VCO Auto Range (Bit 7) to set the correct VCO range automatically. [3] 2x Reference: Enables a frequency doubler prior to the Sysclk PLL and can be useful in reducing jitter induced by the Sysclk PLL. See Figure 28: System Clock Generator Block Diagram, Page 42. [4:6] Reserved [7] VCO Auto Range: Automatic VCO range selection. Enabling this bit allows Bit 2 of this register to be set automatically. Rev. PrA | Page 67 of 78 AD9549 0023; PFD Divider Preliminary Technical Data [3:0] Divide ratio for PFD clock from system clock. This is typically varied only in cases where the designer wishes to run the DPLL Phase detector fast while Sysclk is run relatively slowly. The ratio is equal to PFD Divider * 4. For a 1 GHz system clock, the ADC runs at 1 GHz / 20 = 50 MHz, and the DPLL phase detector runs at half this speed , which in this case is 25 MHz). Digital PLL Control and Dividers 0100; PLL Control [0] Close Loop: Setting this bit closes the loop. If Bit 4 of this register is cleared, then the frequency estimator will be used. If this bit is cleared and the loop is opened, the user should reset the CCI and LF bits of Register 0012 prior to closing the loop again. [1] Loop Polarity: This bit reverses the polarity of the loop response. [2] Unused [3] Enable Frequency Slew Limiter: This bit enables the frequency slew limiter that controls how fast the tuning word can change, and is useful for avoiding runt and stretched pulses during clock switchover and holdover transitions. These values are set in Registers 0127-012C. See “Frequency Slew Limiter” on Page 46. [4] Disable Frequency Estimator. The Frequency Estimator is normally not used, but is useful when the input frequency is unknown, or needs to be qualified. This estimate appears in Registers 115-11A. The Frequency Estimator is not needed when FTW0 (Register 01A6-01AB) is programmed. See “Frequency Estimator“ on Page 47. [5] Single Tone Mode: Setting this bit allows the 9549 to output a tone open loop using FTW0 as DDS tuning word. This bit must be cleared when Bit 0 (Close Loop) is set. This is very useful in debugging when the signal coming into the AD9549 is questionable or nonexistent. [7:6] Reserved 0101 – 0102; R Divider (DPLL Feedforward Divider) [15:0] Feedforward Divider (also called the Reference divider) of the DPLL. Divide Ratio: 1 – 65536. See “Feedforward Divider (Divide-by-R)” on Page 23. If the desired feedfeedforward ratio is greater than 65536, or if the reference input signal on REF_A or REF_B is greater than 400 MHz, then Bit 0, R103 must be set. 0103; R Divider (continued) [0] Divide by 2: Setting this bit enables an additional /2 pre-scalar, effectively doubling the range of the Feedforward Divider. If the desired feedfeedforward ratio is greater than 65536, or if the reference input signal on REF_A or REF_B is greater than 400 MHz, then this bit must be set. [6:1] Unused [7] Falling Edge Triggered: Setting this bit inverts the reference clock before R divider. 0104 – 0105; S Divider (DPLL Feedback Divider) [15:0] Feedback Divider: Divide Ratio: 1 – 65536. If the desired feedback ratio is greater than 65536, or if the feedback signal on FDBK_IN is greater than 400 MHz, then Bit 0, R106 must be set. Rev. PrA | Page 68 of 78 Preliminary Technical Data 0106; S Divider (continued) AD9549 [0] Divide by 2: Setting this bit enables an additional /2 pre-scalar. See “Feedback Divider (Divide-by-S)” on Page 23. If the desired feedback ratio is greater than 65536, or if the feedback signal on FDBK_IN is greater than 400 MHz, then this bit must be set. An example of this case is when the PLL is locking to an image of the DAC output that is above the Nyquist frequency. [6:1] Unused [7] Falling Edge Triggered: Setting this bit inverts the reference clock before the S divider. Digital PLL Loop Filter 0107; P Divider [4:0] Divide Ratio: Controls the ratio of DAC sample rate to loop filter sample rate. See “Digital Loop Filter” on Page 24. Loop filter sample rate = DAC Sample rate / 2^(Divide Ratio[4:0]). For the default case of 1 GHz DAC sample rate, and P Divider [4:0] of 5, the loop filter sample rate is 31.25 MHz. Note: The DAC sample rate is the same as System Clock. 0108 – 0109; Loop Coefficients (See ”Digital Loop Filter Coefficients” on Page 28.) (Note : The AD9549 evaluation software will derive these values.) [11:0] Alpha-0: Linear coefficient for “alpha” coefficient 010A; Loop Coefficients (continued) [4:0] Alpha-1: Power of 2 multiplier for “alpha” coefficient 010B; Loop Coefficients (continued) [3:0] Alpha-2: Power of 2 divider for “alpha” coefficient 010C – 010D; Loop Coefficients (continued) [11:0] Beta-0: Linear coefficient for “beta” coefficient 010E; Loop Coefficients (continued) [2:0] Beta-1: Power of 2 divider for “beta” coefficient 010F – 0110; Loop Coefficients (continued) [11:0] Gamma-0: Linear coefficient for “gamma” coefficient 0111; Loop Coefficients (continued) [2:0] Gamma -1: Power of 2 divider for “gamma” coefficient 0112 – 0114; Reserved 0115 – 011A; FTW Estimate (Read-Only) [47:0] FTW Estimate: This is frequency estimate from frequency estimator circuit, and is informational only. It’s useful for verifying the input reference frequency. See “Frequency Estimator“ on Page 47 for a description. Rev. PrA | Page 69 of 78 AD9549 011B – 0120; FTW Lower Limit Preliminary Technical Data [47:0] FTW Lower Limit: Lowest DDS tuning word in closed loop mode. This feature is recommended when a bandpass reconstruction filter is used. See “Output Frequency Range Control” on Page 39. 0121 – 0126; FTW Upper Limit [47:0] FTW Upper Limit: Highest DDS tuning word in closed loop mode. This feature is recommended when a bandpass reconstruction filter is used. See “Output Frequency Range Control” on Page 39. 0127 – 012C; Frequency Slew Limit [47:0] Frequency Slew Limit: See “Frequency Slew Limiter” on Page 46. 012D – 0130; Reserved Free-Run (Single-Tone) Mode 01A0 – 01A5; Reserved 01A6 – 01AB; FTW0 [47:0] FTW0: FTW (Frequency Tuning Word) for DDS when loop is not “closed” (see register 0100 bit 0) Also used as the initial frequency estimate when the estimator is disabled (see register 0100 bit 4) Note: The power up default is defined by startup pins S1-S4. See “Default DDS Output Frequency on Power-Up” on Page 49. 01AC – 01AD; Phase [15:0] DDS Phase Word: Allows user to vary the phase of the DDS output. Active only when loop is not “closed.” Reference Selector / Holdover 01C0; Automatic Control [0] Automatic Holdover: Setting this bit permits state-machine to enter holdover (free-run) mode. [1] Automatic Recover: Setting this bit permits state-machine to leave holdover mode. [2] Automatic Selector: Setting this bit permits state-machine to switch the active reference clock input. [3] Reserved [4] Holdover Mode: This bit determines which Frequency Tuning Word (FTW) is used in Holdover Mode. 0: Use last FTW at time of holdover. 1: Use averaged FTW at time of holdover, which is the recommended setting. The number of averages used is set in Register 01C2. Rev. PrA | Page 70 of 78 Preliminary Technical Data 01C1; Override [0] Holdover On/Off: This bit controls the status of holdover when Bit 1 of this register is set. AD9549 [1] Enable Holdover Override: Setting this bit disables automatic holdover, and allows user to enter/exit holdover manually via Bit 0 (see above). Setting this bit overrides the HOLDOVER pin. [2] Ref_AB: This bit selects the input when Bit 3 of this register is set. 0 equals REF_A. [3] Enable Ref Input Override: Setting this bit disables automatic reference switchover, and allows user to switch references manually via Bit 2 of this register. Setting this bit overrides the REFSELECT pin. [4] Enable Line-Card Mode: Enables line-card mode of reference switch MUX, which eliminates the possibility of a runt pulse during switchover. See “Use of Line Card Mode to Eliminate Runt Pulses” on Page 35. 01C2; Averaging Window [3:0] FTW Windowed Average Size: This register sets the number of FTWs (frequency tuning words) that are used for calculating the average FTW. Bit 4 in Register 01C0 enables this feature. The number of averages equals 2(FTW Windowed Average Size [3:0]). These samples are taken at the rate of (fs / 2^PIO). 01C3; Reference Validation [4:0] Recovery Timer: The value in this register sets the time required to validate a reference after a LOR or OOL event before the reference can be used as the DPLL reference. This circuit uses the digital loop filter clock (see Register 0107). Validation time = Loop filter clock period * 2(Recovery Timer[4:0] +1) -1. Assuming power-on defaults, the recovery time varies from 32 ns (00000) to 137 sec (11111). If longer validation times are required, the user can make the P divider larger. [6:5] Unused [7] Disable Recovery Timer: Setting these bits disables the recovery timer and requires that references be manually validated. (see Register 01C4) 01C4; Reference Validation (continued); [0] Validate RefB: Mark RefB as valid either prior to the recovery timer or instead of the timer, and is enabled by setting Bit 7 in Register 01C3. This bit is self-clearing, and the self-clearing operation will clear the Validate RefA bit. [1] Validate RefA: Mark RefA as valid either prior to the recovery timer or instead of the timer, and is enabled by setting Bit 7 in Register 01C3. This bit is not self-clearing. The user should set this bit, and then clear it. Doubler and Output Drivers 0200; HSTL Driver [2:0] HSTL Output Doubler: 01: Doubler disabled. 00: Doubler enabled. [3:2] Unused [4] OPOL: Output polarity: Setting this bit inverts the HSTL driver output polarity. 0201; CMOS Driver [0] User MUX control: This bit allows the user to select whether the CMOS driver output is divided by the S Divider. 0: S divider input sent to CMOS driver. 1: S divider output sent to CMOS driver. See Figure 8: Detailed Block Diagram on Page 22. Rev. PrA | Page 71 of 78 AD9549 Monitor Preliminary Technical Data 0300; Status: This register contains the status of the chip. This register is read-only and live update. [0] Frequency Lock Detect: This flag indicates that the “Frequency Lock Detect” circuit has detected frequency lock. [1] Phase Lock Detect: This flag indicates that the “Phase Lock Detect” circuit has detected phase lock. [2] Free Run: DPLL is in holdover mode (free-run) [3] Reference Selected: 0: Reference A is active. 1: Reference B is active. [4] Frequency Estimator Done: True when the “Frequency Estimator” circuit has successfully estimated the input frequency. See “Frequency Estimator” on Page 47. [5] PFD Frequency too Low: This flag indicates that the Frequency Estimator failed and detected too low of a PFD frequency. This bit is only relevant if the user is relying on the Frequency Estimator to determine the input frequency. [6] PFD Frequency too High: This flag indicates that the Frequency Estimator failed and detected too high of a PFD frequency. This bit is only relevant if the user is relying on the Frequency Estimator to determine the input frequency. [7] Unused 0301; Status (continued): This register contains the status of the chip. This register is read-only and live update. [0] RefB OOL: The “OOL” (Out of Limits) circuit has determined that Reference B is out of limits. [1] RefB LOR: A “LOR” (Loss of Reference) has occurred on Reference B. [2] RefB Valid: The Reference Validation circuit has successfully determined that Reference B is valid. [3] Unused [4] RefA OOL: The “OOL” (Out of Limits) circuit has determined that Reference A is out of limits. [5] RefA LOR: A “LOR” (Loss of Reference) has occurred on Reference A. [6] RefA Valid: The Reference Validation circuit has successfully determined that Reference A is valid. [7] Unused 0302 – 0303; IRQ Status; These registers contain the chip status (Registers 0300 – 0301) at the time of IRQ. These bits are cleared with an IRQ reset (see Register 0012, Bit 5). 0304; IRQ Mask [0] Enter Free Run: Trigger IRQ when DPLL enters free-running (holdover) mode. [1] Leave Free Run: Trigger IRQ when DPLL leaves free-running (holdover) mode [2] Reference Changed: Trigger IRQ when active reference clock selection changes [7:3] Unused Rev. PrA | Page 72 of 78 Preliminary Technical Data 0305; IRQ Mask (continued) [0] Frequency Lock: Trigger IRQ on rising edge of “Frequency Lock” signal [1] Frequency Unlock: Trigger IRQ on falling edge of “Frequency Lock” signal [2] Phase Lock: Trigger IRQ on rising edge of “Phase Lock” signal [3] Phase Unlock: Trigger IRQ on falling edge of “Phase Lock” signal [4] Frequency Estimator Done: Trigger IRQ when the “Frequency Estimator” is done 0306; IRQ Mask (continued) [0] !RefA OOL: Trigger IRQ on falling edge of reference A’s OOL [1] RefA OOL: Trigger IRQ on rising edge of reference A’s OOL [2] !RefA LOR: Trigger IRQ on falling edge of reference A’s LOR [3] RefA LOR: Trigger IRQ on rising edge of reference A’s LOR [4] !RefA Valid: Trigger IRQ on falling edge of reference A’s “Valid” [5] RefA Valid: Trigger IRQ on rising edge of reference A’s “Valid” [7:6] Unused 0307; IRQ Mask (continued) [0] !RefB OOL: Trigger IRQ on falling edge of reference B’s OOL [1] RefB OOL: Trigger IRQ on rising edge of reference B’s OOL [2] !RefB LOR: Trigger IRQ on falling edge of reference B’s LOR [3] RefB LOR: Trigger IRQ on rising edge of reference B’s LOR [4] !RefB Valid: Trigger IRQ on falling edge of reference B’s “Valid” [5] RefB Valid: Trigger IRQ on rising edge of reference B’s “Valid” [7:6] Unused AD9549 Rev. PrA | Page 73 of 78 AD9549 0308; S1 Pin Configuration (See “Status and Warnings” on Page 48.) Preliminary Technical Data Note: The choice of input for a given pin must be all Ref A or all Ref B, and not a combination thereof. [0] IRQ: Select “IRQ” signal for output on this pin [1] Reserved [2] Frequency Lock: Select “Frequency Lock” signal for output on this pin [3] Phase Lock: Select “Phase Lock” signal for output on this pin [4] Ref? Not Valid: Select either RefA (0) or RefB (1) “Not Valid” signal for output on this pin [5] Ref? OOL: Select either RefA (0) or RefB (1) “OOL” signal for output on this pin [6] Ref?: LOR: Select either RefA (0) or RefB (1) “LOR” signal for output on this pin [7] Ref?: Choose either RefA (0) or RefB (1) for use with bits 4 – 6 0309; S2 Pin Configuration: Same as register 0308, except applies to pin S2 030A; S3 Pin Configuration: Same as register 0308, except applies to pin S3 030B; S4 Pin Configuration: Same as register 0308, except applies to pin S4 030C; Control [0] Enable Frequency Lock Detector. Register 0319 must be set up to use this. See “Frequency Lock Detection” on Page 32. [1] Enable Phase Lock Detector: Register 0314h-0318h must be set up to use this. See “Phase Lock Detection” on Page 31. [3:2] Unused [4] Enable RefB OOL: The RefB OOL limits are set up in Registers 032C to 0335. [5] Enable RefB LOR: The RefA LOR limits are set up in Registers 0320 to 0321. [6] Enable RefA OOL: The RefB OOL limits are set up in Registers 0322 to 032B. [7] Enable RefA LOR: The RefB LOR limits are set up in Registers 031E to 031F. 030D; Unused 030E – 0313; HFTW; Read-Only [47:0] Average or Instantaneous FTW: This read-only register is the output of FTW monitor. Average or Instantaneous is determined by “Holdover Mode” (see Bit 4, Register 01C0). These registers must be manually refreshed by issuing an IO_UPDATE. 0314 – 0317; Phase Lock [31:0] Phase Lock Threshold: See “Phase Lock Detection” on Page 31. 0318; Phase Lock (continued) [7:5] Phase Unlock Watchdog Timer : See “Phase Lock Detection” on Page 31. [4:0] Phase Lock Watchdog Timer : See “Phase Lock Detection” on Page 31. Rev. PrA | Page 74 of 78 Preliminary Technical Data 0319 – 031C; Frequency Lock [31:0] Frequency Lock Threshold: See “Frequency Lock Detection” on Page 32. 031D; Frequency Lock (continued) [7:5] Frequency Unlock Watchdog Timer: See “Frequency Lock Detection” on Page 32. [4:0] Frequency Lock Watchdog Timer: See “Frequency Lock Detection” on Page 32. 031E – 031F; Loss of Reference [15:0] RefA LOR Divider: See “Loss of Reference” on Page 33. 0320 – 0321; Loss of Reference (continued) [15:0] RefB LOR Divider: See “Loss of Reference” on Page 33. 0322 – 0323; Reference Out Of Limits (OOL) [15:0] RefA OOL Divider: See “Reference Frequency Monitor” on Page 33. 0324 – 0327; Reference OOL (continued) [31:0] RefA OOL Upper Limit: See “Reference Frequency Monitor” on Page 33. 0328 – 032B; Reference OOL (continued) [31:0] RefA OOL Lower Limit: See “Reference Frequency Monitor” on Page 33. 032C – 032D; Reference OOL (continued) [15:0] RefB OOL Divider: See “Reference Frequency Monitor” on Page 33. 032E – 0331; Reference OOL (continued) [31:0] RefB OOL Upper Limit: See “Reference Frequency Monitor” on Page 33. 0332 – 0335; Reference OOL (continued) [31:0] RefB OOL Lower Limit: See “Reference Frequency Monitor” on Page 33. AD9549 Calibration (User Accessible Trim) 0400 – 0401; K Divider [15:0] K Divider: The K divider alters precision of frequency estimator circuit. See “Frequency Estimator” on Page 47. 0402; CPFD Gain [2:0] CPFD Gain Scale: This register is the coarse phase frequency power of 2 multiplier (PDS). See “Phase Detector” on Page 27. Note that the correct value for this register will be calculated by filter design software provided with the evaluation board. 0403; CPFD Gain (continued) [5:0] CPFD Gain: This register is the coarse phase frequency linear multiplier (PDG). See “Phase Detector” on Page 27. Note that the correct value for this register will be calculated by filter design software provided with the evaluation board. Rev. PrA | Page 75 of 78 AD9549 0404; FPFD Gain Preliminary Technical Data [7:0] FPFD Gain: This register is the fine phase frequency detector linear multiplier (alters charge-pump current). See “Fine Phase Detector” on Page 27. Note that the correct value for this register will be calculated by filter design software provided with the evaluation board. 0405 – 0408; Unused 0409 – 040A; PFD Offset [13:0] DPLL Phase Offset: This register controls the static time offset of the PFD (Phase Frequency Detector) in closed-loop mode. It has no effect when the DPLL is open. 040B; DAC Full-scale Current: [7:0] DAC Full-scale Current: DAC Full-scale Current [7:0]. See “DAC Output” on Page 27. 040C; DAC Full-scale Current [1:0] DAC Full-scale Current: DAC Full-scale Current [9:8]. See Register 040B. 040D – 040E; Unused 040F; Reference Bias Level [1:0] DC Input Level for VDDX @ 3.3 V: This register sets the DC bias level for the reference inputs. The value should be chosen such that VIH is as close as possible to (but not exceeding) 3.3V. 00: VDD3 – 800 mV 01: VDD3 – 400 mV 10: VDD3 – 1.6 V 11: VDD3 – 1.2 V [7:2] Reserved 0410; Unused Rev. PrA | Page 76 of 78 Preliminary Technical Data Harmonic Spur Reduction 0500; Spur A: See “Harmonic Spur Reduction” on Page 77. [3:0] Spur A Harmonic 1 – 15 [5:4] Unused [6] Amplitude Gain x2 [7] Harmonic Spur Reduction A Enable (HSR-A Enable) 0501 – 0502; Spur A (continued) [7:0] Spur A Magnitude: Linear multiplier for Spur A magnitude 0503 – 0504; Spur A (continued) [8:0] Spur A Phase: Linear offset for Spur A phase 0505; Spur B [3:0] Spur B Harmonic: 1 – 15 [5:4] Unused [6] Amplitude Gain x2 [7] Harmonic Spur Reduction B Enable (HSR-B Enable) 0506 – 0507; Spur B (continued) [7:0] Spur B Magnitude: Linear multiplier for Spur B magnitude 0508 – 0509; Spur B (continued) [8:0] Spur B Phase: Linear offset for Spur B phase AD9549 Rev. PrA | Page 77 of 78 AD9549 OUTLINE DIMENSIONS a 64-Lead Lead Frame Chip Scale Package [LFCSP] 9 x 9 mm Body (CP-64-1) Dimensions shown in millimeters Preliminary Technical Data 9.00 BSC SQ 0.60 MAX 0.60 MAX 49 48 0.30 0.25 0.18 64 1 PIN 1 INDICATOR PIN 1 INDICATOR TOP VIEW 8.75 BSC SQ (BOTTOM VIEW) EXPOSED PAD 4.85 4.70 SQ* 4.55 0.45 0.40 0.35 33 32 16 17 1.00 0.85 0.80 12 MAX 0.80 MAX 0.65 TYP 0.05 MAX 0.02 NOM 0.50 BSC 7.50 REF SEATING PLANE 0.20REF * COMPLIANT TO JEDEC STANDARDS MO-220-VMMD EXCEPT FOR EXPOSED PAD DIMENSION Figure 45: Outline Dimensions ORDERING GUIDE Model AD9549BCPZ1(when released) AD9549XCPZ1 (prototypes) 1 Temperature Range -40 to +85 -40 to +85 Package Description 64-lead LFCSP 64-lead LFCSP Package Option Z = Pb-free part. ©2007 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. PR06744-0-3/07(PrA) Rev. PrA | Page 78 of 78