ADG792GBCPZ-REEL

I2C-Compatible, Wide Bandwidth, Triple 4:1 Multiplexer ADG792A/ADG792G FEATURES FUNCTIONAL BLOCK DIAGRAMS VDD VDD GND ADG792A ADG792G S1A S1A S1B S1B D1 S1C S1D S2A S2A S2B S2B D2 S2C S2D S3A S3A S3B D3 S3C D3 S3C S3D S3D I2C SERIAL INTERFACE A0 RGB/YPbPr video switches HDTV Projection TV DVD-R/RW AV receivers D2 S2C S2D S3B D1 S1C S1D APPLICATIONS GND A1 I2C SERIAL INTERFACE GPO1 A2 SDA SCL A0 A1 A2 SDA SCL GPO2 06029-001 Bandwidth: 190 MHz Low insertion loss and on resistance: 2.6 Ω typical On resistance flatness: 0.3 Ω typical Single 3 V/5 V supply operation 3.3 V analog signal range (5 V supply, 75 Ω load) Low quiescent supply current: 1 nA typical Fast switching times: tON 185 ns, tOFF 181 ns I2C®-compatible interface Compact, 24-lead, LFCSP package Two I2C-controllable logic outputs ESD protection 4 kV human body model 200 V machine model 1 kV field-induced charged device model Figure 1. GENERAL DESCRIPTION The ADG792A/ADG792G are monolithic CMOS devices, each comprising three 4:1 multiplexer/demultiplexers that are controllable through a standard I2C serial interface. The CMOS process provides ultralow power dissipation yet delivers high switching speed and low on resistance. The on resistance profile is very flat over the full analog input range, and wide bandwidth ensures excellent linearity and low distortion. These features, combined with a wide input signal range, make the ADG792A/ADG792G the ideal switching solution for a wide range of TV applications, including RGB and YPbPr video switches. When turned on, the switches conduct equally well in both directions. In the off condition, signal levels, up to the supplies, are blocked. The ADG792A/ADG792G switches exhibit breakbefore-make switching action. The ADG792G also has two general-purpose logic output pins controllable through the I2C interface to control other non-I2C-compatible devices, such as video filters. The integrated I2C interface provides a large degree of flexibility in the system design. To build larger switching arrays, the user can set the three I2C address pins allowing as many as eight devices to connect to the same bus. The ADG792A/ADG792G operate from a single 3 V or 5 V supply voltage and is available in a compact 4 mm × 4 mm body, 24-lead, Pb-free, LFCSP package. PRODUCT HIGHLIGHTS 1. Wide bandwidth: 190 MHz. 2. Ultralow power dissipation. 3. Extended input signal range. 4. Integrated I2C serial interface. 5. Compact 4 mm × 4 mm, 24-lead, Pb-free LFCSP package. 6. ESD protection tested as per ESD Association Standards: 4 kV HBM (ANSI/ESD STM5.1-2001) 200 V MM (ANSI/ESD STM5.2-1999) 1 kV FICDM (ANSI/ESDSTM5.3.1-1999) Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2006 Analog Devices, Inc. All rights reserved. ADG792A/ADG792G TABLE OF CONTENTS Features .............................................................................................. 1 Terminology .................................................................................... 16 Applications....................................................................................... 1 Theory of Operation ...................................................................... 17 Functional Block Diagrams............................................................. 1 I2C Serial Interface ..................................................................... 17 General Description ......................................................................... 1 I2C Address.................................................................................. 17 Product Highlights ........................................................................... 1 Write Operation.......................................................................... 17 Revision History ............................................................................... 2 LDSW Bit..................................................................................... 19 Specifications..................................................................................... 3 Power On/Software Reset.......................................................... 19 I2C Timing Specifications............................................................ 7 Read Operation........................................................................... 19 Absolute Maximum Ratings............................................................ 9 Evaluation Board ............................................................................ 20 ESD Caution.................................................................................. 9 Using the ADG792G Evaluation Board .................................. 20 Pin Configurations and Function Descriptions ......................... 10 Outline Dimensions ....................................................................... 23 Typical Performance Characteristics ........................................... 11 Ordering Guide .......................................................................... 23 Test Circuits..................................................................................... 14 REVISION HISTORY 7/06—Revision 0: Initial Version Rev. 0 | Page 2 of 24 ADG792A/ADG792G SPECIFICATIONS VDD = 5 V ± 10%, GND = 0 V, TA = −40°C to +85°C, unless otherwise noted. Table 1. Parameter ANALOG SWITCH Analog Signal Range 2 On Resistance, RON On Resistance Matching Between Channels, ∆RON On Resistance Flatness, RFLAT(ON) LEAKAGE CURRENTS Source Off Leakage (IS(OFF)) Drain Off Leakage (ID(OFF)) Channel On Leakage (ID(ON), IS(ON)) DYNAMIC CHARACTERISTICS 3 tON, tENABLE tOFF, tDISABLE Break-Before-Make Time Delay, tD I2C to GPO Propagation Delay, tH, tL Off Isolation Channel-to-Channel Crosstalk Same Multiplexer Different Multiplexer −3 dB Bandwidth THD + N Charge Injection CS(OFF) CD(OFF) CD(ON), CS(ON) Power Supply Rejection Ratio, PSRR Differential Gain Error Differential Phase Error LOGIC INPUTS (A0, A1, A2)3 Input High Voltage, VINH Input Low Voltage, VINL Input Current, IINL or IINH Input Capacitance, CIN LOGIC INPUTS (SCL, SDA)3 Input High Voltage, VINH Input Low Voltage, VINL Input Leakage Current, IIN Input Hysteresis Input Capacitance, CIN Conditions Min VS = VDD, RL = 1 MΩ VS = VDD, RL = 75 Ω VD = 0 V, IDS = −10 mA, see Figure 22 VD = 0 V to 1 V, IDS = −10 mA, see Figure 22 VD = 0 V IDS = −10 mA VD = 1 V IDS = −10 mA VD = 0 V to 1 V, IDS = −10 mA 0 0 Typ 1 2.6 0.15 0.3 Max Unit 4 3.3 3.5 4 V V Ω Ω 0.5 0.6 0.55 Ω Ω Ω VD = 4 V/1 V, VS = 1 V/4 V, see Figure 23 VD = 4 V/1 V, VS = 1 V/4 V, see Figure 23 VD = VS = 4 V/1 V, see Figure 24 ±0.25 nA ±0.25 nA ±0.25 nA CL = 35 pF, RL = 50 Ω, VS = 2 V, see Figure 28 CL = 35 pF, RL = 50 Ω, VS = 2 V, see Figure 28 CL = 35 pF, RL = 50 Ω, VS1 = VS2 = 2 V, see Figure 29 ADG792G only f = 10 MHz, RL = 50 Ω, see Figure 26 f = 10 MHz, RL = 50 Ω, see Figure 27 185 240 ns 181 235 ns 1 3 ns 130 RL = 50 Ω, see Figure 25 RL = 100 Ω CL = 1 nF, VS = 0 V, see Figure 30 f = 20 kHz CCIR330 test signal CCIR330 test signal −60 ns dB −55 −75 190 0.14 5 10 26 37 70 0.58 0.81 dB dB MHz % pC pF pF pF dB % Degrees 2.0 VIN = 0 V to VDD 0.005 3 0.7 × VDD −0.3 VIN = 0 V to VDD Rev. 0 | Page 3 of 24 +0.005 0.05 × VDD 3 0.8 ±1 VDD + 0.3 +0.3 × VDD ±1 V V μA pF V V μA V pF ADG792A/ADG792G Parameter LOGIC OUTPUTS3 SDA Pin Output Low Voltage, VOL Floating State Leakage Current Floating State Output Capacitance GPO1 and GPO2 Pins Output Low Voltage, VOL Output High Voltage, VOH POWER REQUIREMENTS IDD 1 2 3 Conditions Min Typ1 ISINK = 3 mA ISINK = 6 mA ILOAD = +2 mA ILOAD = −2 mA Digital inputs = 0 V or VDD, I2C interface inactive I2C interface active, fSCL = 400 kHz I2C interface active, fSCL = 3.4 MHz All typical values are at TA = +25°C, unless otherwise stated. Guaranteed by initial characterization, not subject to production test. Guaranteed by design, not subject to production test. Rev. 0 | Page 4 of 24 Max Unit 0.4 0.6 ±1 10 V V μA pF 0.4 V V 1 μA 0.2 0.7 mA mA 2.0 0.001 ADG792A/ADG792G VDD = 3 V ± 10%, GND = 0 V, TA = −40°C to +85°C, unless otherwise noted. Table 2. Parameter ANALOG SWITCH Analog Signal Range2 On Resistance, RON On Resistance Matching Between Channels, ∆RON On Resistance Flatness, RFLAT(ON) LEAKAGE CURRENTS Source Off Leakage (IS(OFF)) Drain Off Leakage (ID(OFF)) Channel On Leakage (ID(ON), IS(ON)) DYNAMIC CHARACTERISTICS3 tON, tENABLE tOFF, tDISABLE Break-Before-Make Time Delay, tD I2C to GPO propagation delay, tH, tL Off Isolation Channel-to-Channel Crosstalk Same Multiplexer Different Multiplexer −3 dB Bandwidth THD + N Charge Injection CS(OFF) CD(OFF) CD(ON), CS(ON) Power Supply Rejection Ratio, PSRR Differential Gain Error Differential Phase Error LOGIC INPUTS (A0, A1, A2)3 Input High Voltage, VINH Input Low Voltage, VINL Input Current, IINL or IINH Input Capacitance, CIN LOGIC INPUTS (SCL, SDA)3 Input High Voltage, VINH Input Low Voltage, VINL Input Leakage Current, IIN Input Hysteresis Input Capacitance, CIN LOGIC OUTPUTS3 SDA Pin Output Low Voltage, VOL Conditions Min VS = VDD, RL = 1 MΩ VS = VDD, RL = 75 Ω VD = 0 V, IS = −10 mA, see Figure 22 VD = 0 V to 1 V, IS = −10 mA, see Figure 22 VD = 0 V IS = −10 mA VD = 1 V IS = −10 mA VD = 0 V to 1 V, IS = −10 mA 0 0 Typ1 3 0.15 0.8 VD = 2 V/1 V, VS = 1 V/2 V, see Figure 23 VD = 2 V/1 V, VS = 1 V/2 V, see Figure 23 VD = VS = 2 V/1 V, see Figure 24 ±0.25 ±0.25 ±0.25 CL = 35 pF, RL = 50 Ω, VS = 2 V, see Figure 28 CL = 35 pF, RL = 50 Ω, VS = 2 V, see Figure 28 CL = 35 pF, RL = 50 Ω, VS1 = VS2 = 2 V, see Figure 29 ADG792G only f = 10 MHz, RL = 50 Ω, see Figure 26 f = 10 MHz, RL = 50 Ω, see Figure 27 200 197 3 1 RL = 50 Ω, see Figure 25 RL = 100 Ω CL = 1 nF, VS = 0 V, see Figure 30 f = 20 kHz CCIR330 test signal CCIR330 test signal Max Units 2.2 1.7 4 6 0.6 0.8 2.8 V V Ω Ω Ω Ω Ω nA nA nA 260 255 ns ns ns 121 −60 ns dB −55 −75 180 0.14 3.5 10 26 37 70 0.49 0.56 dB dB MHz % pC pF pF pF dB % Degrees 2.0 VIN = 0 V to VDD +0.005 3 0.7 × VDD −0.3 VIN = 0 V to VDD +0.005 0.05 × VDD 3 ISINK = 3 mA ISINK = 6 mA Floating State leakage Current Floating State Output Capacitance 3 Rev. 0 | Page 5 of 24 0.8 ±1 V V μA pF VDD + 0.3 +0.3 × VDD ±1 V V μA V pF 0.4 0.6 ±1 V V μA pF ADG792A/ADG792G Parameter GPO1 and GPO2 Pins Output Low Voltage, VOL Output High Voltage, VOH POWER REQUIREMENTS IDD Conditions Min ILOAD = +2 mA ILOAD = −2 mA 2.0 Digital inputs = 0 V or VDD, I2C interface inactive I2C interface active, fSCL = 400 kHz I2C interface active, fSCL = 3.4 MHz 1 All typical values are at TA = +25°C, unless otherwise stated. Guaranteed by initial characterization, not subject to production test. 3 Guaranteed by design, not subject to production test. 2 Rev. 0 | Page 6 of 24 Typ1 0.001 Max Units 0.4 V V 1 μA 0.1 0.2 mA mA ADG792A/ADG792G I2C TIMING SPECIFICATIONS VDD = 2.7 V to 5.5 V; GND = 0 V; TA = −40°C to +85°C, unless otherwise noted. See Figure 2 for timing diagram. Table 3. Parameter 1 fSCL t1 t2 t3 t4 2 t5 t6 t7 t8 t9 t10 t11 Conditions Standard mode Fast mode High speed mode CB = 100 pF max CB = 400 pF max Standard mode Fast mode High speed mode CB = 100 pF max CB = 400 pF max Standard mode Fast mode High speed mode CB = 100 pF max CB = 400 pF max Standard mode Fast mode High speed mode Standard mode Fast mode High speed mode CB = 100 pF max CB = 400 pF max Standard mode Fast mode High speed mode Standard mode Fast mode High speed mode Standard mode Fast mode Standard mode Fast mode High speed mode Standard mode Fast mode High speed mode CB = 100 pF max CB = 400 pF max Standard mode Fast mode High speed mode CB = 100 pF max CB = 400 pF max Standard mode Fast mode High speed mode CB = 100 pF max CB = 400 pF max Min Max 100 400 Unit kHz kHz 3.4 1.7 4 0.6 MHz MHz μs μs 60 120 4.7 1.3 ns ns μs μs 160 320 250 100 10 0 0 ns ns ns ns ns μs μs 3.45 0.9 0 0 4.7 0.6 160 4 0.6 160 4.7 1.3 4 0.6 160 703 150 1000 300 ns ns μs μs ns μs μs ns μs μs μs μs ns ns ns 80 160 300 300 ns ns ns ns 20 + 0.1 CB 80 160 1000 300 ns ns ns ns 10 20 40 80 ns ns 20 + 0.1 CB B 10 20 20 + 0.1 CB B 10 20 B Description Serial clock frequency tHIGH, SCL high time tLOW, SCL low time tSU;DAT, data setup time tHD;DAT, data hold time tSU;STA, setup time for a repeated start condition tHD;STA, hold time (repeated) start condition tBUF, bus free time between a stop and a start condition tSU;STO, setup time for stop condition tRDA, rise time of SDA signal tFDA, fall time of SDA signal tRCL, rise time of SCL signal Rev. 0 | Page 7 of 24 ADG792A/ADG792G Parameter 1 t11A t12 tSP 1 2 Conditions Standard mode Fast mode High speed mode CB = 100 pF max CB = 400 pF max Standard mode Fast mode High speed mode CB = 100 pF max CB = 400 pF max Fast mode High speed mode Min Max 1000 300 Unit ns ns 20 + 0.1 CB 80 160 300 300 ns ns ns ns 10 20 0 0 40 80 50 10 ns ns ns ns 20 + 0.1 CB B 10 20 B Description tRCL1, rise time of SCL signal after a repeated start condition and after an acknowledge bit tFCL, fall time of SCL signal Pulse width of suppressed spike Guaranteed by initial characterization. CB refers to capacitive load on the bus line, tr and tf measured between 0.3 VDD and 0.7 VDD. A device must provide a data hold time for SDA in order to bridge the undefined region of the SCL falling edge. Timing Diagram t11 t2 SCL t12 t6 t1 t6 t4 t5 t3 t8 t10 t9 t7 P S S Figure 2. Timing Diagram for 2-Wire Serial Interface Rev. 0 | Page 8 of 24 P 06029-002 SDA ADG792A/ADG792G ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. Table 4. Parameter VDD to GND Analog, Digital Inputs Continuous Current, S or D Pins Peak Current, S or D Pins Operating Temperature Range Industrial (B Version) Storage Temperature Range Junction Temperature θJA Thermal Impedance 24-Lead LFCSP Lead Temperature, Soldering (10 sec) IR Reflow, Peak Temperature (