ADM8699ARW

a Microprocessor Supervisory Circuits ADM8698/ADM8699 FUNCTIONAL BLOCK DIAGRAM FEATURES Superior Upgrade for ADM698/ADM699, MAX698/MAX699 Guaranteed RESET Assertion with VCC = 1 V Low 70 mA Supply Current Precision 4.65 V Voltage Monitor Power OK/Reset Time Delay Watchdog Timer Minimum Component Count Performance Specified over Temperature APPLICATIONS Microprocessor Systems Computers Controllers Intelligent Instruments Automotive Systems Critical mP Power Monitoring ADM8698/ ADM8699 RESET* VCC RESET GENERATOR RESET 4.65V WATCHDOG INPUT WDI* WATCHDOG TRANSITION DETECTOR (1 sec) WATCHDOG OUTPUT WDO* *WDI (ADM8699 ONLY) RESET (SOIC ONLY) WDO (ADM8699 SOIC ONLY) TYPICAL APPLICATION CIRCUIT +5V GENERAL DESCRIPTION The ADM8698/ADM8699 supervisory circuits provide power supply monitoring and watchdog timing for microprocessor systems. The ADM8698 monitors the 5 V VCC power supply and generates a RESET pulse during power up, power down and during low voltage “Brown Out” conditions. The RESET output is guaranteed to be functional (logic low) with VCC as low as 1 V. The ADM8699 features an identical monitoring circuit as in the ADM8698, plus an additional watchdog timer input to monitor microprocessor activity. The RESET output is forced low if the watchdog input is not toggled within the 1 second watchdog timeout period. µP POWER VCC RESET ADM8698/ ADM8699 µP RESET µP SYSTEM WDI* I/O LINE GND *ADM8699 ONLY Both parts are available in 8-pin plastic DIP/SOIC and 16-lead SOIC packages. The 16-lead SOIC contains additional outputs RESET (without inversion) and Watchdog Output WDO (ADM8699 only). REV. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 617/329-4700 World Wide Web Site: http://www.analog.com Fax: 617/326-8703 © Analog Devices, Inc., 1997 ADM8698/ADM8699–SPECIFICATIONS (V Parameter Min VCC Operating Voltage Range Supply Current 3.0 Power-Down Reset Assertion Power-Up Reset Deassertion Reset Threshold Hysteresis Reset Active Time Watchdog Timeout Period (ADM8699) Minimum WDI Input Pulse Width 1.0 50 CC = +5 V 6 10%, TA = TMIN to TMAX unless otherwise noted) Typ Max Units 70 5.5 100 V µA 4.5 4.65 4.75 V 140 40 200 280 mV ms 1.6 2.25 RESET Output Voltage RESET Output Voltage (VCC = 1 V) 0.4 200 12 3.5 RESET and WDO Output Voltage 0.4 3.5 RESET Output Short Circuit Current WDI Input Threshold (ADM8699) Logic Low Logic High WDI Input Current 45 0.8 3.5 –10 +1 –1 +10 Test Conditions/Comments s ns VIL = 0.4, VIH = 0.8 (VCC) V mV V V V mA ISINK = 3.2 mA, VCC = 4.4 V ISINK = 100 µA, VCC = 1.0 V ISOURCE = 500 µA, VCC = 5 V ISINK = 3.2 mA, VCC = 5 V ISOURCE = 1 µA, VCC = 4.4 V Output Sink Current V V µA µA WDI = VCC WDI = 0 V Specifications subject to change without notice. ABSOLUTE MAXIMUM RATINGS* ORDERING GUIDE (TA = +25°C unless otherwise noted) VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +6 V All Other Inputs . . . . . . . . . . . . . . . . . . . –0.3 V to VCC + 0.3 V Power Dissipation 8-Pin DIP . . . . . . . . . . . . . . . . . . . . 500 mW θJA, Thermal Impedance . . . . . . . . . . . . . . . . . . . . +120°C/W Power Dissipation 16-Pin SOIC . . . . . . . . . . . . . . . . . 375 mW θJA, Thermal Impedance . . . . . . . . . . . . . . . . . . . . +110°C/W Power Dissipation 8-Pin SOIC . . . . . . . . . . . . . . . . . . 500 mW θJA, Thermal Impedance . . . . . . . . . . . . . . . . . . . . +125°C/W Operating Temperature Range Industrial (A Version) . . . . . . . . . . . . . . . . . –40°C to +85°C Storage Temperature Range . . . . . . . . . . . . . –65°C to +150°C Lead Temperature (Soldering, 10 secs) . . . . . . . . . . . . +300°C Vapor Phase (60 secs) . . . . . . . . . . . . . . . . . . . . . . . +215°C Infrared (15 secs) . . . . . . . . . . . . . . . . . . . . . . . . . . . +220°C ESD Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >4 kV Model Temperature Range Package Options* ADM8698AN ADM8698ARW ADM8698ARN –40°C to +85°C –40°C to +85°C –40°C to +85°C N-8 R-16 R-8 ADM8699AN ADM8699ARW ADM8699ARN –40°C to +85°C –40°C to +85°C –40°C to +85°C N-8 R-16 R-8 *N = Plastic DIP; R = Small Outline. *Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum ratings for extended periods of time may affect device reliability. –2– REV. 0 ADM8698/ADM8699 PIN FUNCTION DESCRIPTIONS Function VCC GND RESET +5 V Power Supply Input. 0 V. Ground reference for all signals. Logic Output. RESET goes low whenever VCC falls below the reset voltage threshold (4.65 V typ). RESET remains low for a minimum of 140 ms after VCC returns to 5 V. RESET also goes low for a minimum of 140 ms if the watchdog timer is enabled but not serviced within its timeout period. Watchdog Input. WDI is a three level input. If WDI remains either high or low for longer than the watchdog timeout period, RESET pulses low and WDO goes low. The timer resets with each transition on the WDI line. The watchdog timer may be disabled if WDI is left floating or is driven to midsupply. (SOIC packages only) Logic Output. RESET is an active high output. It is the inverse of RESET. (SOIC ADM8699 only) Logic Output. The Watchdog Output, WDO, goes low if WDI remains either high or low for longer than the watchdog timeout period. WDO is set high by the next transition at WDI. If WDI is unconnected or at midsupply, the watchdog timer is disabled and WDO remains high. WDI RESET WDO TYPICAL PERFORMANCE CURVES A4 90 10 0% 1V 220 8 GND 2 ADM8698/ ADM8699 O 7 RESET GND 3 TOP VIEW (Not to Scale) 6 NC (WDI)* GND 4 5 NC 210 200 190 180 170 –50 *( ) ADM8699 ONLY 16-Lead SOIC VCC 3 GND 4 16 RESET O ADM8698/ TOP VIEW ADM8699 (Not to Scale) 90 4.65 4.63 4.61 4.59 4.57 –30 0 30 60 TEMPERATURE – °C 90 120 Figure 3. RESET Voltage Threshold vs. Temperature 14 NC (WDO)* 13 NC NC 6 11 NC (WDI)* NC 7 10 NC 9 GND *( ) ADM8699 ONLY NC = NO CONNECT REV. 0 70 15 RESET TOP VIEW NC 5 (Not to Scale) 12 NC NC 8 10 30 50 TEMPERATURE – °C 4.67 4.55 –60 VCC 2 –10 4.69 NC = NO CONNECT GND 1 –30 Figure 2. RESET Timeout Delay vs. Temperature RESET VOLTAGE THRESHOLD – V 1 500ms 230 8-Lead DIP & SOIC VCC 1V Figure 1. RESET Output Voltage vs. VCC PIN CONFIGURATIONS VCC 3.36 V 100 RESET DELAY – ms Mnemonic –3– ADM8698/ADM8699 Watchdog Timer (ADM8699 Only) The watchdog timer input (WDI) monitors an I/O line from the µP system. The µP must toggle this input once every 1.6 seconds to verify correct software execution. Failure to toggle the line indicates that the µP system is not correctly executing its program and may be tied up in an endless loop. If this happens, a reset pulse is generated to initialize the processor. A precision voltage detector monitors VCC and generates a RESET output to hold the microprocessor’s Reset line low when VCC falls below the reset threshold 4.65 V (see Figure 4). The reset voltage threshold is set to accommodate a 5% variation on VCC. The voltage detector has 40 mV hysteresis to ensure that glitches on VCC do not activate the RESET output. The WDI input is a three level input and will recognize a lowto-high or high-to-low transition on its input. The watchdog timer is reset by each WDI transition and then begins its timeout period. If the WDI pin remains either high or low, reset pulses will be issued every 1.6 seconds typically. If the watchdog timer is not needed, the WDI input should be left floating. On power-up, an internal monostable holds RESET low for 140 ms after VCC rises above the reset threshold. This allows the power supply to stabilize on power-up and also prevents repeated toggling of RESET even if the 5 V power drops out and recovers with each power line cycle. In order to prevent mistriggering due to transient voltage spikes, it is recommended that a 0.1 µF capacitor be connected at the VCC pin. The Watchdog Output (WDO) (SOIC package Only) provides watchdog status information. It is driven low if WDI is not toggled within the watchdog timeout period. It goes high at the next WDI transition. It is also set high when VCC falls below the reset threshold. The RESET output is guaranteed to remain low with VCC, as low as 1 V. This holds the microprocessor in a stable shutdown condition as the power supply comes up. On the 16-lead SOIC package, an active high RESET output is also provided. This is the complement of RESET and is intended for microprocessors requiring an active high signal. VCC V2 V2 V1 C2926–10–2/97 CIRCUIT INFORMATION Power Fail RESET WDI V1 WDO t1 RESET t2 t1 t2 RESET V1 = RESET VOLTAGE THRESHOLD t1 V2 = RESET VOLTAGE THRESHOLD + THRESHOLD HYSTERESIS t1 = RESET TIME t1 t1 t1 = RESET TIME t2 = WATCHDOG TIME OUT PERIOD Figure 4. Watchdog Timeout Period vs. Temperature Figure 5. Watchdog Timeout Period and Reset Active Time OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 8-Pin Plastic DIP (N-8) 8-Pin SOIC (R-8) 16-Lead SOIC (R-16) 8 5 8 0.25 0.31 (6.35) (7.87) PIN 1 1 0.2440 (6.20) 0.2284 (5.80) 4 0.430 (10.92) MAX 0.125 (3.18) MIN 0.18 (4.57) 0.018 (0.46) 0.1 (2.54) BSC SEATING PLANE 1 4 0.1574 (4.00) 0.1497 (3.80) 0.3 (7.62) 0.419 (10.65) 1 0.0098 (0.25) 0.0040 (0.10) 8 0.413 (10.50) 0.0500 0.0192 (0.49) SEATING (1.27) 0.0138 (0.35) PLANE BSC 0.012 (0.3) 0.0196 (0.50) x 45° 0.0099 (0.25) 0.033 (0.84) 0.18 (4.57) MAX 0.011 (0.28) 9 0.299 (7.60) 0.102 (2.59) 0.094 (2.39) PIN 1 0.035 (0.89) 16 5 0.104 (2.65) 0.05 (1.27) REF 0.019 (0.49) 0.030 (0.75) 0.0098 (0.25) 0.0075 (0.19) 8° 0° 0.0500 (1.27) 0.0160 (0.41) –4– 0.013 (0.32) 0.042 (1.07) REV. 0 PRINTED IN U.S.A. 0.1968 (5.00) 0.1890 (4.80)