ADP3607ARU-5-REEL7

a 50 mA Switched Capacitor Voltage Boost with Regulated Output ADP3607 FUNCTIONAL BLOCK DIAGRAM FEATURES Fully Regulated Output Voltage (5 V and Adjustable) Input Voltage Range From 3 V to 5 V 50 mA Output Current Output Accuracy: ⴞ5% High Switching Frequency: 250 kHz SO-8 and TSSOP-8 Packages –40ⴗC to +85ⴗC Ambient Temperature Range S1 V S3 IN S4 S2 V OUT TE APPLICATIONS Computer Peripherals and Add-On Cards Portable Instruments Battery Powered Devices Pagers and Radio Control Receivers Disk Drives Mobile Phones SD OSC CLOCK GEN FB V SENSE 1.5 V VREF LE GENERAL DESCRIPTION CP– CP+ GND B SO The ADP3607 is a 50 mA regulated output switched capacitor voltage doubler. It provides a regulated output voltage with minimum voltage loss and requires a minimum number of external components. In addition, the ADP3607 does not require the use of an inductor. The internal oscillator of the ADP3607 runs at 500 kHz nominal frequency, which produces an output switching frequency of 250 kHz. This allows for the use of smaller charge pump and filter capacitors. O The ADP3607 provides an accuracy of ± 5% with a typical shutdown current of 150 µA. It can also operate from a single positive input voltage as low as 3 V. The ADP3607 is offered with the regulation fixed at 5 V, or adjustable via external resistors over a 3 V to 9 V range. SD103 D1 VIN 3.3V VOUT VIN *CIN+ 4.7mF CP+ *CP 4.7mF + + VOUT 5.0V *CO 4.7mF ADP3607-5 CP– SD OFF GND VSENSE ON 0 *FOR BEST PERFORMANCE, 10mF IS RECOMMENDED CP : SPRAGUE, 293D475X0010B2W CIN, CO: TOKIN, 1E475ZY5UC205F Figure 1. Typical Application Circuit REV. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/326-8703 © Analog Devices, Inc., 1999 ADP3607–SPECIFICATIONS1, 2, 3(V IN = 3.3 V @ TA = +25ⴗC, CP = CO = 4.7 ␮F unless otherwise noted.) Parameter Symbol Condition OPERATING SUPPLY RANGE VS SUPPLY CURRENT Shutdown Mode IS –40°C < TA < +85°C VSD = VIN, –40°C < TA < +85°C VO VO IO = 25 mA IO = 10 mA to 50 mA –40°C ≤ TA ≤ +85°C 3.0 V ≤ VS ≤ 3.6 V LOAD REGULATION ∆VO/IO IO = 10 mA–25 mA IO = 10 mA–50 mA OUTPUT RESISTANCE (Open Loop) RO OUTPUT RIPPLE VOLTAGE VRIPPLE Min Typ Max Units 3.0 3.3 5 V 3.5 150 6 200 mA µA 5 5 5.15 5.25 V V OUTPUT VOLTAGE4 VIH IIH VIL IIL 0.3 0.25 mV/mA mV/mA 11 Ω TE SHUTDOWN Logic Input High Input Current Logic Input Low Input Current fS CIN = CO = 4.7 µF ILOAD = 25 mA ILOAD = 50 mA 16 31 VIN = 3.3 V –40°C < TA < +85°C 212 250 288 2.4 LE SWITCHING FREQUENCY 4.85 4.75 1 0.4 1 mV mV kHz V µA V µA B SO NOTES 1 Capacitors CIN, CO and CP in the test circuit are 4.7 µF with 0.1 Ω ESR. Capacitors with higher ESR may reduce output voltage and efficiency. 2 See Figure 1 conditions. 3 All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods. 4 For the adjustable version, a 1% resistor should be used to maintain output voltage tolerance. For both device types, tolerances can be improved by >1% using larger value and lower ESR capacitors for C O and C P. Specifications subject to change without notice. ABSOLUTE MAXIMUM RATINGS 1 (TA = +25°C unless otherwise noted) Input Voltage (VIN to GND) . . . . . . . . . . . . . . . . . . . . +7.5 V Output Voltage (VOUT to GND) . . . . . . . . . . . . . . . . . . +12 V Output Short Circuit Protection . . . . . . . . . . . . . . . . . . . 1 sec θJA, SO-8 Package2 . . . . . . . . . . . . . . . . . . . . . . . . . 150°C/W θJA, TSSOP-8 Package2 . . . . . . . . . . . . . . . . . . . . . . 208°C/W Operating Temperature Range . . . . . . . . . . . –40°C to +85°C Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C Lead Temperature Range (Soldering 10 sec) . . . . . . . . +300°C Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . +215°C Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . +220°C ORDERING GUIDE Model Output Voltage Package Option* ADP3607AR-5 ADP3607AR ADP3607ARU-5 ADP3607ARU 5 V, 50 mA Adjustable, 50 mA 5 V, 50 mA Adjustable, 50 mA SO-8 SO-8 RU-8 RU-8 O *SO = Small Outline Package; RU = Thin Small Outline Package. Contact the factory for the availability of other output voltage options. NOTES 1 This is a stress rating only, operation beyond these limits can cause the device to be permanently damaged. 2 θJA is specified for worst case conditions with device soldered on a circuit board. CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the ADP3607 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. –2– WARNING! ESD SENSITIVE DEVICE REV. 0 ADP3607 Table I. Other Members of ADP360x Family 1 PIN FUNCTION DESCRIPTIONS Model Output Current Package Option2 Comments ADP3603AR ADP3604AR ADP3605AR-3 ADP3605AR 50 mA 120 mA 120 mA 120 mA SO-8 SO-8 SO-8 SO-8 Nom. –3 V ± 3% Inverter Nom. –3 V ± 3% Inverter Nom. –3 V ± 5% Inverter Adj. Output Inverter Pin Mnemonic NOTES 1 See individual data sheets for detailed ordering information. 2 SO = Small Outline package. 1 2 CP+ VIN 3 4 CP – SD 5 VSENSE Life High Freq Temp Size Cost Aluminum Electrolytic Capacitor Fair Fair Fair Small Low Multilayer Ceramic Capacitor Long Good Poor Fair High Solid Tantalum Capacitor Above Avg Avg Avg Avg Avg OS-CON Capacitor Above Avg Good Good Good Avg 6 7 8 NC GND VOUT LE Type Positive Terminal for the Pump Capacitor. Input Voltage. Connect a low ESR bypass capacitor between this pin and device ground to minimize supply transients. Negative Terminal for the Pump Capacitor. Logic Level Shutdown. Apply a logic Hi or connect to VIN to shut down the device. In Shutdown mode, the charge pump is turned off and quiescent current is reduced. Apply a logic low or connect to ground for normal operation. Output Voltage Sense Line. This is used to improve load regulation by eliminating IR drops on the high current carrying output traces. For normal operation, connect VSENSE to VOUT. See Application Information section for more detail. No Connection. Ground. Regulated Output Voltage. Connect a low ESR, 4.7 µF or larger capacitor between this pin and device GND. TE Table II. Alternative Capacitor Technologies Function B SO PIN CONFIGURATION Table III. Recommended Capacitor Manufacturers Manufacturer Capacitor Sprague 672D, 673D, 674D, 678D 675D, 173D, 199D PF and PL TDC and TDL MLCC GRM Sprague Aluminum Electrolytic Tantalum Aluminum Electrolytic Tantalum Multilayer Ceramic Multilayer Ceramic O Nichicon Mallory TOKIN MuRata Capacitor Type REV. 0 –3– 8 VOUT CP+ 1 ADP3607 7 GND TOP VIEW CP– 3 (Not to Scale) 6 NC VIN 2 SD 4 5 VSENSE NC = NO CONNECT 270 4.00 265 3.75 SUPPLY CURRENT – mA 260 VIN = +3.3V 3.25 VIN = +3.0V 3.5 4.0 4.5 SUPPLY VOLTAGE – Volts 3.00 –40 5.0 Figure 2. Oscillator Frequency vs. Supply Voltage –15 10 35 TEMPERATURE – 8C 60 85 Figure 5. Supply Current vs. Temperature in Normal Mode 300 OSCILLATOR FREQUENCY – kHz 5.05 IL = 10mA IL = 25mA 5.01 4.99 IL = 50mA B SO 4.97 4.95 –40 –15 10 35 TEMPERATURE – 8C 60 85 O 100 260 240 220 200 –40 –15 10 35 TEMPERATURE – 8C 60 85 Figure 6. Oscillator Frequency vs. Temperature OUTPUT VOLTAGE – Volts Figure 3. Output Voltage vs. Temperature 125 280 LE 5.03 OUTPUT VOLTAGE – Volts VIN = +4.0V 3.50 255 250 3.0 AVERAGE INPUT CURRENT – mA VIN = +5.0V TE OSCILLATOR FREQUENCY – kHz ADP3607 –Typical Performance Characteristics 75 50 5.05 5.00 4.95 VIN = +5.0V 4.90 VIN = +4.0V 4.85 VIN = +3.3V 4.80 VIN = +3.0V 25 4.75 0 4.70 10 15 20 25 30 35 40 OUTPUT CURRENT – mA 45 50 0 Figure 4. Average Input Current vs. Output Current 25 50 75 125 100 LOAD CURRENT – mA 150 175 200 Figure 7. Output Voltage vs. Load Current –4– REV. 0 ADP3607 3.7 300 250 SUPPLY CURRENT – mA SUPPLY CURRENT – mA 3.6 FIXED VERSION 3.5 ADJUSTABLE VERSION R = 38kV 3.4 200 FIXED VERSION 150 100 ADJUSTABLE VERSION R = 38kV 50 3.5 4.0 4.5 SUPPLY VOLTAGE – Volts 0 3.0 5.0 Figure 8. Supply Current vs. Supply Voltage in Normal Mode 4.0 4.5 SUPPLY VOLTAGE – Volts 5.0 Figure 11. Supply Current vs. Supply Voltage in Shutdown Mode 240 80 VIN = +5.0V 70 LE 220 60 200 EFFICIENCY – % SUPPLY CURRENT – mA 3.5 TE 3.3 3.0 VIN = +4.0V 180 160 VIN = +3.3V 50 40 30 B SO 20 140 VIN = +3.0V 120 –40 –15 10 35 TEMPERATURE – 8C 60 85 Figure 9. Supply Current vs. Temperature in Shutdown Mode 10 0 0 10 20 30 LOAD CURRENT – mA VO = +5.0V VOUT O VOUT T CH1 2.00V CH2 2.00V M2.00ms CH2 VO = +4.96V VO = 0V IO = 50mA IL VIN = +3.3V IO = 1mA VIN = 0V CH2 20.0mV BW M4.00ms CH4 CH4 10.0mV V BW 1.12V Figure 10. Start-up Under Full Load Based on Circuit of Figure 1 REV. 0 50 Figure 12. Efficiency vs. Load Current Based on Circuit of Figure 1 VO = +5.0V VIN 40 9.0mV Figure 13. Load Transient Response Based on Circuit of Figure 1 –5– ADP3607 THEORY OF OPERATION When selecting the capacitors, keep in mind that not all manufacturers guarantee capacitor ESR in the range required by the circuit. In general, the capacitor’s ESR is inversely proportional to its physical size, so larger capacitance values and higher voltage ratings tend to reduce ESR. Since the ESR is also a function of the operating frequency, when selecting a capacitor make sure its value is rated at the circuit’s operating frequency. Another factor affecting capacitor performance is temperature. The ADP3607 uses a switched capacitor principle to generate a regulated boost voltage from a positive input voltage. An on-board oscillator generates a two-phase clock to control a switching network that transfers charge between the storage capacitors. The switches turn on and off at a 250 kHz rate that is generated from an internal 500 kHz oscillator. The basic principle behind the voltage conversion scheme is illustrated in Figures 14 and 15. VIN S1 S2 CP S4 Figure 16 illustrates the temperature effect on various capacitors. If the circuit has to operate at temperatures significantly different from +25°C, the capacitance and ESR values must be carefully selected to adequately compensate for the change. Various capacitor technologies offer improved performance over temperature; for example, certain tantalum capacitors provide good low temperature ESR but at a higher cost. Table II provides the ratings for different types of capacitor technologies to help the designer select the right capacitors for the application. The exact values of CIN and CO are not critical. However, low ESR capacitors such as solid tantalum and multilayer ceramic capacitors are recommended to minimize voltage loss at high currents. Table III shows a partial list of the recommended low ESR capacitor manufacturers. VOUT + – S3 TE Figure 14. ADP3607 Switch Configuration Charging the Pump Capacitor LE During phase one, S1 and S3 are ON, charging the pump capacitor to the input voltage. Before the next phase begins, S1 and S3 are turned OFF, as are S2 and S4 to prevent any overlap. S2 and S4 are turned ON during the second phase (see Figure 15) and charge stored in the pump capacitor is transferred to the output capacitor. 40 S1 S2 CP S4 VOUT + – S3 B SO Figure 15. ADP3607 Switch Configuration Charging the Output Capacitor During the second phase, the negative terminal of the pump capacitor is connected to VIN through variable resistance switch S4, and the positive terminal is connected to the output, resulting in a voltage shift at the output terminal. The ADP3607 block diagram is shown on the front page. 10 ADP3607-5 35 OUTPUT RIPPLE – mV VIN 30 ILOAD = 50mA 25 20 150mV 15 100mV 10 50mV 5 0 20 ALUMINUM 40 60 80 100 CAPACITANCE – mF 120 140 Figure 17. Output Ripple Voltage (mV) vs. Capacitance and ESR Input Capacitor CERAMIC A small 1 µF input bypass capacitor (preferably with low ESR) such as tantalum or multilayer ceramic, is recommended to reduce noise and supply transients, and supply part of the peak input current drawn by the ADP3607. A large capacitor is recommended if the input supply is connected to the ADP3607 through long leads, or if the pulse current drawn by the device might affect other circuitry through supply coupling. O ESR – V 1.0 TANTALUM 0.1 ORGANIC SEMIC 0.01 –50 0 50 TEMPERATURE – 8C Output Capacitor 100 The output capacitor (CO) is alternately charged to the CP voltage when CP is switched in parallel with CO. The ESR of CO introduces steps in the VOUT waveform whenever the charge pump charges CO, which contributes to VOUT ripple. Thus, ceramic or tantalum capacitors are recommended for CO to minimize ripple on the output. Figure 17 illustrates the output ripple voltage effect for various capacitance and ESR values. Note that as the capacitor value increases beyond the point where the dominant contribution to the output ripple is due to the ESR, no significant reduction in VOUT ripple is achieved by added capacitance. Since output current is supplied solely by Figure 16. ESR vs. Temperature APPLICATION INFORMATION Capacitor Selection The ADP3607’s high internal oscillator frequency permits the use of small capacitors for both the pump and the output capacitors. For a given load current, factors affecting the output voltage performance are: • Pump (CP) and output (CO) capacitance. • ESR of the CP and CO. –6– REV. 0 ADP3607 the output capacitor, CO, during one-half of the charge-pump cycle, peak-to-peak output ripple voltage is calculated by using the following formula. VRIPPLE = IL 2 × FPUMP × CO Because of the external Schottky diode between VIN and VOUT, the output voltage will be held to a diode drop below VIN when the ADP3607 is in shutdown mode. Power Dissipation + 2 × I L × ESRCO The power dissipation of the ADP3607 circuit must be limited such that the junction temperature of the device does not exceed the maximum junction temperature rating. Total power dissipation is calculated as follows: where IL = Load Current P = (2 VIN – VOUT) IOUT + (VIN) IS FPUMP = 250 kHz nominal switching frequency CO = 10 µF with an ESR of 0.15 Ω VRIPPLE = Where IOUT and IS are output current and supply current, VIN and VOUT are input and output voltages respectively. 50 mA + 2 × 50 mA × 0.15 = 25 mV 2 × 250 kHz × 10 µF For example: assuming worst case conditions, VIN = 5 V, VOUT = 5 V, IOUT = 50 mA and IS = 6 mA. Calculated device power dissipation is: TE Multiple smaller capacitors can be connected in parallel to yield lower ESR and potential cost savings. For lighter loads, proportionally smaller capacitors are required. To reduce high frequency noise, bypass the output with a 0.1 µF ceramic capacitor in parallel with the output capacitor. P ≈ (2 × 5 V – 5 V)(0.05 A) + (5 V)(0.006 A) = 280 mW This is far below the 660 mW power dissipation capability of the ADP3607. General Board Layout Guidelines Pump Capacitor Since the ADP3607’s internal switches turn on and off very quickly, good PC board layout practices are critical to ensure optimal operation of the device. Improper layouts will result in poor load regulation, especially with heavy loads. Following these simple layout guidelines will improve output performance. A low ESR capacitor has much greater impact on performance for CP than CO since current through CP is twice the CO current. Therefore, the voltage drop due to CP is about four times the ESR of CP times the load current. While the ESR of CO affects the output ripple voltage, the voltage drop generated by the ESR of CP, combined with the voltage drop due to the output source resistance, determines the maximum available VOUT. 2. Use single point ground for device ground and input and output capacitor grounds. Improved Load Regulation Maximum unregulated output voltage can be obtained by connecting the VSENSE pin to ground instead of to the VOUT pin (see Figure 18). Under this condition, the magnitude of the unregulated output voltage depends on the load current. VOUT is inversely proportional to the load current. LE The ADP3607 alternately charges CP to the input voltage when CP is switched in parallel with the input supply, and then transfers charge to CO when CP is switched in parallel with CO. During the time CP is charging, the peak current is approximately two times the output current. During the time CP is delivering charge to CO, the supply current drops down to about 3 mA. 1. Use adequate ground and power traces or planes. B SO 3. Keep external components as close to the device as possible. 4. Use short traces from the input and output capacitors to the input and output pins respectively. Maximum Output Voltage O In most applications, IR drops due to printed circuit board traces are not critical. VSENSE should be connected to the output at a convenient pcb location close to the load. However, if a reduction in IR drops, or improvement in load regulation is desired, the sense line can be used to monitor the output voltage at the load. To avoid excessive noise pickup, keep the VSENSE line as short as possible and away from any noisy line. The ADP3607’s output can be disabled by pulling the SD Pin to a TTL /CMOS logic high level which will stop the internal oscillator. Applying a logic low will turn ON the oscillator. If the shutdown feature is not used, the SD pin should be tied to ground. The shutdown mode current is dominated by the resistor divider connected to the VSENSE pin. This current can be calculated using one of the following formulas. 5 V fixed output version: (VIN – 0.3V ) 23.75 kΩ 6.7 VIN = 3.3V 6.5 IN5819 6.3 D1 VIN 6.1 CIN 5.9 VIN VOUT + CP + 4.7mF 4.7mF CP+ VSENSE CP– SD GND VO + CO 4.7mF 5.5 0 Adjustable output version: 5 10 15 20 25 30 35 OUTPUT CURRENT – mA 40 45 50 Figure 18. Maximum Unregulated Output Voltage (VIN – 0.3 V ) = (9.5 kΩ + REXT ) where REXT is in kΩ. REV. 0 VIN = 3.6V 6.9 5.7 I SENSE(SD ) = I SENSE(SD ) 7.1 OUTPUT VOLTAGE – Volts Shutdown Mode 7.3 –7– ADP3607 Regulated Adjustable Output Voltage D3 IN5819 4.7mF VSENSE VIN CIN 4.7mF VIN SD + GND Figure 20. Regulated 12 V from a 5 V Input Regulated Dual Supply System The circuit in Figure 21 provides regulated positive and negative voltages for systems that require dual supplies from a single battery or power supply. 10mF + CP1 10mF 5.5 IN5819 B SO D1 VIN = 3.3V R VSENSE CP– SD GND 4.7mF 4.0 CP+ + 0 5 10 4.7mF 15 20 25 30 35 OUTPUT CURRENT – mA 40 45 CP2 10mF O PIN 1 0.0098 (0.25) 0.0040 (0.10) 5 4 CP+ 10mF VSENSE CP– GND SD + –2.6V VOUT CP+ R1 16.5kV 1% VSENSE CO2 +10mF CP– SD GND Figure 21. Regulated Dual Supply System OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 8-Lead TSSOP (RU-8) 0.122 (3.10) 0.114 (2.90) 0.1968 (5.00) 0.1890 (4.80) 1 +5V O1 VIN 8-Lead SOIC (SO-8) 8 +C 50 Figure 19. Regulated Adjustable Output Voltage 0.1574 (4.00) 0.1497 (3.80) VOUT ADP3605 CO R = 24.9kV 3.5 VIN PRINTED IN U.S.A. 4.5 + + ADP3607-5 VO VIN VOUT CP R1 104.5kV +C CP– LE R = 47.5kV CIN 4.7mF SD103 6.0 OUTPUT VOLTAGE – Volts VOUT O VIN = +3.3V 4.7mF O2 D1 1N5819 ADP3607 CP+ CP + 4.7mF R +1 9.5 6.5 + 12V +C where VOUT is in volts and R is in kΩs. 5.0 D2 SD103 TE VOUT = C1 4.7mF + C3500–8–8/99 For the adjustable version of the ADP3607, the regulated output voltage is programmed by a resistor that is inserted between the VSENSE and VOUT pins, as illustrated in Figure 19. The inherent limit of the output voltage of a single doubling charge pump stage is two times the input voltage. The scaling factor of 2.00 is reduced somewhat due to losses that increase with output current. To increase the scaling factor to attain a more positive output voltage, an external pump stage can be added with just passive components as shown in Figure 20. That single stage increases the scaling factor to a limit of 3, although the diode drops will limit the ability to noticeably attain that exact 3.00 scaling factor. Even further increases can be achieved with more external pump stages. High accuracy on the adjustable output is achieved through the use of precision trimmed internal resistors, which eliminates the need to trim the external resistor or add a second resistor to form a divider. The adjustable output voltage is set using the following formula: 8 0.2440 (6.20) 0.2284 (5.80) 0.0688 (1.75) 0.0532 (1.35) 0.0500 0.0192 (0.49) SEATING (1.27) 0.0098 (0.25) PLANE BSC 0.0138 (0.35) 0.0075 (0.19) 5 0.177 (4.50) 0.169 (4.30) 0.256 (6.50) 0.246 (6.25) 0.0196 (0.50) x 45° 0.0099 (0.25) 1 4 PIN 1 0.0256 (0.65) BSC 8° 0° 0.0500 (1.27) 0.0160 (0.41) 0.006 (0.15) 0.002 (0.05) SEATING PLANE –8– 0.0118 (0.30) 0.0075 (0.19) 0.0433 (1.10) MAX 0.0079 (0.20) 0.0035 (0.090) 88 08 0.028 (0.70) 0.020 (0.50) REV. 0