Data Sheet
Ultraprecision, Low Noise, 2.048 V/2.500 V/
3.00 V/5.00 V XFET® Voltage References
ADR420/ADR421/ADR423/ADR425
FEATURES
PIN CONFIGURATION
Low noise (0.1 Hz to 10 Hz)
ADR420: 1.75 μV p-p
ADR421: 1.75 μV p-p
ADR423: 2.0 μV p-p
ADR425: 3.4 μV p-p
Low temperature coefficient: 3 ppm/°C
Long-term stability: 50 ppm/1000 hours
Load regulation: 70 ppm/mA
Line regulation: 35 ppm/V
Low hysteresis: 40 ppm typical
Wide operating range
ADR420: 4 V to 18 V
ADR421: 4.5 V to 18 V
ADR423: 5 V to 18 V
ADR425: 7 V to 18 V
Quiescent current: 0.5 mA maximum
High output current: 10 mA
Wide temperature range: −40°C to +125°C
TP 1
VIN 2
ADR420/
ADR421/
ADR423/
ADR425
8
TP
7
NIC
VOUT
TOP VIEW
GND 4 (Not to Scale) 5 TRIM
6
NIC = NO INTERNAL CONNECTION
TP = TEST PIN (DO NOT CONNECT)
02432-001
NIC 3
Figure 1. 8-Lead SOIC, 8-Lead MSOP
GENERAL DESCRIPTION
The ADR42x are a series of ultraprecision, second generation
eXtra implanted junction FET (XFET) voltage references
featuring low noise, high accuracy, and excellent long-term
stability in SOIC and MSOP footprints.
Patented temperature drift curvature correction technique and
XFET technology minimize nonlinearity of the voltage change
with temperature. The XFET architecture offers superior
accuracy and thermal hysteresis to the band gap references. It
also operates at lower power and lower supply headroom than
the buried Zener references.
APPLICATIONS
Precision data acquisition systems
High resolution converters
Battery-powered instrumentation
Portable medical instruments
Industrial process control systems
Precision instruments
Optical network control circuits
The superb noise and the stable and accurate characteristics
of the ADR42x make them ideal for precision conversion
applications such as optical networks and medical equipment.
The ADR42x trim terminal can also be used to adjust the output voltage over a ±0.5% range without compromising any
other performance. The ADR42x series voltage references
offer two electrical grades and are specified over the extended
industrial temperature range of −40°C to +125°C. Devices have
8-lead SOIC or 30% smaller, 8-lead MSOP packages.
ADR42x PRODUCTS
Table 1.
Model
ADR420
ADR421
ADR423
ADR425
Rev. J
Output Voltage, VOUT (V)
2.048
2.50
3.00
5.00
mV
1, 3
1, 3
1.5, 4
2, 6
Initial Accuracy
%
0.05, 0.15
0.04, 0.12
0.04, 0.13
0.04, 0.12
Temperature Coefficient (ppm/°C)
3, 10
3, 10
3, 10
3, 10
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2001–2013 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADR420/ADR421/ADR423/ADR425
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Device Power Dissipation Considerations .............................. 17
Applications ....................................................................................... 1
Basic Voltage Reference Connections ..................................... 17
Pin Configuration ............................................................................. 1
Noise Performance ..................................................................... 17
General Description ......................................................................... 1
Turn-On Time ............................................................................ 17
ADR42x Products ............................................................................. 1
Applications..................................................................................... 18
Revision History ............................................................................... 3
Output Adjustment .................................................................... 18
Specifications..................................................................................... 4
ADR420 Electrical Specifications............................................... 4
Reference for Converters in Optical Network Control
Circuits......................................................................................... 18
ADR421 Electrical Specifications............................................... 5
High Voltage Floating Current Source .................................... 18
ADR423 Electrical Specifications............................................... 6
Kelvin Connections .................................................................... 19
ADR425 Electrical Specifications............................................... 7
Dual-Polarity References ........................................................... 19
Absolute Maximum Ratings ............................................................ 8
Programmable Current Source ................................................ 20
Thermal Resistance ...................................................................... 8
Programmable DAC Reference Voltage .................................. 20
ESD Caution .................................................................................. 8
Precision Voltage Reference for Data Converters .................. 21
Pin Configurations and Function Descriptions ........................... 9
Precision Boosted Output Regulator ....................................... 21
Typical Performance Characteristics ........................................... 10
Outline Dimensions ....................................................................... 22
Terminology .................................................................................... 16
Ordering Guide .......................................................................... 23
Theory of Operation ...................................................................... 17
Rev. J | Page 2 of 24
Data Sheet
ADR420/ADR421/ADR423/ADR425
REVISION HISTORY
12/13—Rev. I to Rev. J
7/04—Rev. D to Rev. E
Added θJC Values to Table 7.............................................................. 8
Changes to Ordering Guide ...........................................................23
Changes to Ordering Guide ............................................................. 5
5/11—Rev. H to Rev. I
Changes to Table I ............................................................................. 1
Changes to Ordering Guide ............................................................. 4
Updated Outline Dimensions........................................................ 16
Added Endnote 1 in Table 2............................................................. 4
Added Endnote 1 in Table 3............................................................. 5
Added Endnote 1 in Table 4............................................................. 6
Added Endnote 1 in Table 5............................................................. 7
Deleted A Negative Precision Reference Without Precision
Resistors Section ..............................................................................17
Deleted Figure 42; Renumbered Sequentially .............................17
Updated Outline Dimensions ........................................................21
Changes to Ordering Guide ...........................................................22
6/07—Rev. G to Rev. H
Changes to Table 2 ............................................................................ 3
Changes to Table 3 ............................................................................ 4
Changes to Table 4 ............................................................................ 5
Changes to Table 5 ............................................................................ 6
Updated Outline Dimensions ........................................................21
Changes to Ordering Guide ...........................................................22
6/05—Rev. F to Rev. G
Changes to Table 1 ............................................................................ 1
Changes to Ordering Guide ...........................................................22
3/04—Rev. C to Rev. D
1/03—Rev. B to Rev. C
Changed Mini_SOIC to MSOP ........................................ Universal
Changes to Ordering Guide ............................................................. 4
Corrections to Y-axis labels in TPCs 21 and 24 ............................ 9
Enhancement to Figure 13 ............................................................. 15
Updated Outline Dimensions........................................................ 16
3/02—Rev. A to Rev. B
Edits to Ordering Guide ................................................................... 4
Deletion of Precision Voltage Regulator section......................... 15
Addition of Precision Boosted Output Regulator section ........ 15
Addition of Figure 13...................................................................... 15
10/01—Rev. 0 to Rev. A
Addition of ADR423 and ADR425 to
ADR420/ADR421 .............................................................. Universal
5/01—Revision 0: Initial Version
2/05—Rev. E to Rev. F
Updated Format.................................................................. Universal
Updated Outline Dimensions ........................................................21
Changes to Ordering Guide ...........................................................22
Rev. J | Page 3 of 24
ADR420/ADR421/ADR423/ADR425
Data Sheet
SPECIFICATIONS
ADR420 ELECTRICAL SPECIFICATIONS
VIN = 5.0 V to 15.0 V, TA = 25°C, unless otherwise noted.
Table 2.
Parameter
OUTPUT VOLTAGE
A Grade
B Grade
INITIAL ACCURACY 1
A Grade
Symbol
VOUT
Conditions
Typ
Max
Unit
2.045
2.047
2.048
2.048
2.051
2.049
V
V
+3
+0.15
+1
+0.05
mV
%
mV
%
2
1
10
3
10
35
ppm°C
ppm/°C
V
ppm/V
70
ppm/mA
500
600
µA
µA
µV p-p
nV/√Hz
µs
ppm
ppm
dB
mA
VOUTERR
−3
−0.15
−1
−0.05
B Grade
TEMPERATURE COEFFICIENT
A Grade
B Grade
SUPPLY VOLTAGE HEADROOM
LINE REGULATION
TCVOUT
LOAD REGULATION
∆VOUT/∆IL
IL = 0 mA to 10 mA,
−40°C < TA < +125°C
QUIESCENT CURRENT
IIN
VOLTAGE NOISE
VOLTAGE NOISE DENSITY
TURN-ON SETTLING TIME
LONG-TERM STABILITY
OUTPUT VOLTAGE HYSTERESIS
RIPPLE REJECTION RATIO
SHORT CIRCUIT TO GND
eN p-p
eN
tR
∆VOUT
VOUT_HYS
RRR
ISC
No load
−40°C < TA < +125°C
0.1 Hz to 10 Hz
1 kHz
1
Min
VIN − VOUT
∆VOUT/∆VIN
−40°C < TA < +125°C
2
VIN = 5 V to 18 V,
−40°C < TA < +125°C
1000 hours
fIN = 1 kHz
Initial accuracy does not include shift due to solder heat effect.
Rev. J | Page 4 of 24
390
1.75
60
10
50
40
−75
27
Data Sheet
ADR420/ADR421/ADR423/ADR425
ADR421 ELECTRICAL SPECIFICATIONS
VIN = 5.0 V to 15.0 V, TA = 25°C, unless otherwise noted.
Table 3.
Parameter
OUTPUT VOLTAGE
A Grade
B Grade
INITIAL ACCURACY 1
A Grade
Symbol
VOUT
Conditions
Typ
Max
Unit
2.497
2.499
2.500
2.500
2.503
2.501
V
V
+3
+0.12
+1
+0.04
mV
%
mV
%
2
1
10
3
10
35
ppm/°C
ppm/°C
V
ppm/V
70
ppm/mA
500
600
µA
µA
µV p-p
nV/√Hz
µs
ppm
ppm
dB
mA
VOUTERR
−3
−0.12
−1
−0.04
B Grade
TEMPERATURE COEFFICIENT
A Grade
B Grade
SUPPLY VOLTAGE HEADROOM
LINE REGULATION
TCVOUT
LOAD REGULATION
∆VOUT/∆IL
QUIESCENT CURRENT
IIN
VOLTAGE NOISE
VOLTAGE NOISE DENSITY
TURN-ON SETTLING TIME
LONG-TERM STABILITY
OUTPUT VOLTAGE HYSTERESIS
RIPPLE REJECTION RATIO
SHORT CIRCUIT TO GND
eN p-p
eN
tR
∆VOUT
VOUT_HYS
RRR
ISC
1
Min
VIN − VOUT
∆VOUT/∆VIN
−40°C < TA < +125°C
2
VIN = 5 V to 18 V,
−40°C < TA < +125°C
IL = 0 mA to 10 mA,
−40°C < TA < +125°C
No load
−40°C < TA < +125°C
0.1 Hz to 10 Hz
1 kHz
1000 hours
fIN = 1 kHz
Initial accuracy does not include shift due to solder heat effect.
Rev. J | Page 5 of 24
390
1.75
80
10
50
40
−75
27
ADR420/ADR421/ADR423/ADR425
Data Sheet
ADR423 ELECTRICAL SPECIFICATIONS
VIN = 5.0 V to 15.0 V, TA = 25°C, unless otherwise noted.
Table 4.
Parameter
OUTPUT VOLTAGE
A Grade
B Grade
INITIAL ACCURACY 1
A Grade
Symbol
VOUT
Conditions
Typ
Max
Unit
2.996
2.9985
3.000
3.000
3.004
3.0015
V
V
+4
+0.13
+1.5
+0.04
mV
%
mV
%
2
1
10
3
10
35
ppm/°C
ppm/°C
V
ppm/V
70
ppm/mA
500
600
µA
µA
µV p-p
nV/√Hz
µs
ppm
ppm
dB
mA
VOUTERR
−4
−0.13
−1.5
−0.04
B Grade
TEMPERATURE COEFFICIENT
A Grade
B Grade
SUPPLY VOLTAGE HEADROOM
LINE REGULATION
TCVOUT
LOAD REGULATION
∆VOUT/∆IL
QUIESCENT CURRENT
IIN
VOLTAGE NOISE
VOLTAGE NOISE DENSITY
TURN-ON SETTLING TIME
LONG-TERM STABILITY
OUTPUT VOLTAGE HYSTERESIS
RIPPLE REJECTION RATIO
SHORT CIRCUIT TO GND
eN p-p
eN
tR
∆VOUT
VOUT_HYS
RRR
ISC
1
Min
VIN − VOUT
∆VOUT/∆VIN
−40°C < TA < +125°C
2
VIN = 5 V to 18 V,
−40°C < TA < +125°C
IL = 0 mA to 10 mA,
−40°C < TA < +125°C
No load
−40°C < TA < +125°C
0.1 Hz to 10 Hz
1 kHz
1000 hours
fIN = 1 kHz
Initial accuracy does not include shift due to solder heat effect.
Rev. J | Page 6 of 24
390
2
90
10
50
40
−75
27
Data Sheet
ADR420/ADR421/ADR423/ADR425
ADR425 ELECTRICAL SPECIFICATIONS
VIN = 7.0 V to 15.0 V, TA = 25°C, unless otherwise noted.
Table 5.
Parameter
OUTPUT VOLTAGE
A Grade
B Grade
INITIAL ACCURACY 1
A Grade
Symbol
VOUT
Conditions
Typ
Max
Unit
4.994
4.998
5.000
5.000
5.006
5.002
V
V
+6
+0.12
+2
+0.04
mV
%
mV
%
2
1
10
3
10
35
ppm/°C
ppm/°C
V
ppm/V
70
ppm/mA
500
600
µA
µA
µV p-p
nV/√Hz
µs
ppm
ppm
dB
mA
VOUTERR
−6
−0.12
−2
−0.04
B Grade
TEMPERATURE COEFFICIENT
A Grade
B Grade
SUPPLY VOLTAGE HEADROOM
LINE REGULATION
TCVOUT
LOAD REGULATION
∆VO/∆IL
QUIESCENT CURRENT
IIN
VOLTAGE NOISE
VOLTAGE NOISE DENSITY
TURN-ON SETTLING TIME
LONG-TERM STABILITY
OUTPUT VOLTAGE HYSTERESIS
RIPPLE REJECTION RATIO
SHORT CIRCUIT TO GND
eN p-p
eN
tR
∆VO
VO_HYS
RRR
ISC
1
Min
−40°C < TA < +125°C
VIN − VO
∆VO/∆VIN
2
VIN = 7 V to 18 V,
−40°C < TA < +125°C
IL = 0 mA to 10 mA,
−40°C < TA < +125°C
No load
−40°C < TA < +125°C
0.1 Hz to 10 Hz
1 kHz
1000 hours
fIN = 1 kHz
Initial accuracy does not include shift due to solder heat effect.
Rev. J | Page 7 of 24
390
3.4
110
10
50
40
−75
27
ADR420/ADR421/ADR423/ADR425
Data Sheet
ABSOLUTE MAXIMUM RATINGS
These ratings apply at 25°C, unless otherwise noted.
THERMAL RESISTANCE
Table 6.
θJA is specified for the worst-case conditions, that is, θJA is
specified for devices soldered in the circuit board for surfacemount packages.
Parameter
Supply Voltage
Output Short-Circuit Duration to GND
Storage Temperature Range
Operating Temperature Range
Junction Temperature Range
Lead Temperature (Soldering, 60 sec)
Rating
18 V
Indefinite
−65°C to +150°C
−40°C to +125°C
−65°C to +150°C
300°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Table 7.
Package Type
8-Lead MSOP (RM)
8-Lead SOIC (R)
ESD CAUTION
Rev. J | Page 8 of 24
θJA
190
130
θJC
44
43
Unit
°C/W
°C/W
Data Sheet
ADR420/ADR421/ADR423/ADR425
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
TP 1
VIN 2
ADR420/
ADR421/
ADR423/
ADR425
8
TP
7
NIC
VOUT
TOP VIEW
GND 4 (Not to Scale) 5 TRIM
NIC = NO INTERNAL CONNECTION
TP = TEST PIN (DO NOT CONNECT)
02432-002
NIC 3
6
Figure 2. 8-Lead SOIC, 8-Lead MSOP Pin Configuration
Table 8. Pin Function Descriptions
Pin No.
1, 8
Mnemonic
TP
2
3, 7
4
5
VIN
NIC
GND
TRIM
6
VOUT
Description
Test Pin. There are actual connections in TP pins, but they are reserved for factory testing purposes. Users should not
connect anything to TP pins; otherwise, the device may not function properly.
Input Voltage.
No Internal Connect. NICs have no internal connections.
Ground Pin = 0 V.
Trim Terminal. It can be used to adjust the output voltage over a ±0.5% range without affecting the temperature
coefficient.
Output Voltage.
Rev. J | Page 9 of 24
ADR420/ADR421/ADR423/ADR425
Data Sheet
5.0025
2.0493
5.0023
2.0491
5.0021
2.0489
5.0019
2.0487
5.0017
2.0485
2.0483
5.0015
5.0013
2.0481
5.0011
2.0479
5.0009
2.0477
2.0475
–40
–10
20
50
80
110
125
02432-007
VOUT (V)
2.0495
02432-004
VOUT (V)
TYPICAL PERFORMANCE CHARACTERISTICS
5.0007
5.0005
–40
–10
20
50
80
110
125
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 3. ADR420 Typical Output Voltage vs. Temperature
Figure 6. ADR425 Typical Output Voltage vs. Temperature
0.55
2.5015
2.5013
0.50
SUPPLY CURRENT (mA)
2.5011
2.5007
2.5005
2.5003
2.5001
2.4999
+25°C
0.40
–40°C
0.35
02432-005
0.30
2.4997
2.4995
–40
+125°C
0.45
–10
20
50
80
110
02432-008
VOUT (V)
2.5009
0.25
125
4
6
8
TEMPERATURE (°C)
10
12
14
15
INPUT VOLTAGE (V)
Figure 4. ADR421 Typical Output Voltage vs. Temperature
Figure 7. ADR420 Supply Current vs. Input Voltage
0.55
3.0010
3.0008
0.50
SUPPLY CURRENT (mA)
3.0006
3.0002
3.0000
2.9998
2.9996
2.9994
+125°C
0.40
+25°C
0.35
–40°C
–10
20
50
80
110
125
02432-009
2.9992
2.9990
–40
0.45
0.30
02432-006
VOUT (V)
3.0004
0.25
4
TEMPERATURE (°C)
6
8
10
12
14
INPUT VOLTAGE (V)
Figure 5. ADR423 Typical Output Voltage vs. Temperature
Figure 8. ADR421 Supply Current vs. Input Voltage
Rev. J | Page 10 of 24
15
Data Sheet
ADR420/ADR421/ADR423/ADR425
0.55
70
IL = 0mA TO 5mA
60
LOAD REGULATION (ppm/mA)
0.50
0.45
0.40
+25°C
0.35
–40°C
0.30
4
6
8
10
12
14
VIN = 5V
40
30
VIN = 6.5V
20
10
02432-010
0.25
50
0
–40
15
02432-013
SUPPLY CURRENT (mA)
+125°C
–10
INPUT VOLTAGE (V)
20
50
80
110
125
TEMPERATURE (°C)
Figure 9. ADR423 Supply Current vs. Input Voltage
Figure 12. ADR421 Load Regulation vs. Temperature
0.55
70
IL = 0mA TO 10mA
60
LOAD REGULATION (ppm/mA)
+125°C
0.45
0.40
+25°C
0.35
–40°C
0.30
6
8
10
12
14
VIN = 7V
40
30
VIN = 15V
20
10
02432-011
0.25
50
0
–40
15
02432-014
SUPPLY CURRENT (mA)
0.50
–10
INPUT VOLTAGE (V)
Figure 10. ADR425 Supply Current vs. Input Voltage
50
80
110 125
Figure 13. ADR423 Load Regulation vs. Temperature
70
35
VIN = 15V
IL = 0mA TO 10mA
IL = 0mA TO 5mA
60
LOAD REGULATION (ppm/mA)
30
50
40
VIN = 4.5V
30
20
10
0
–40
–10
20
50
80
110
25
20
15
10
5
0
–40
125
TEMPERATURE (°C)
02432-015
VIN = 6V
02432-012
LOAD REGULATION (ppm/mA)
20
TEMPERATURE (°C)
–10
20
50
80
110 125
TEMPERATURE (°C)
Figure 11. ADR420 Load Regulation vs. Temperature
Figure 14. ADR425 Load Regulation vs. Temperature
Rev. J | Page 11 of 24
ADR420/ADR421/ADR423/ADR425
Data Sheet
6
14
VIN = 4.5V TO 15V
VIN = 7.5V TO 15V
12
LINE REGULATION (ppm/V)
4
3
2
1
–10
20
50
80
8
6
4
2
02432-016
0
–40
10
02432-019
LINE REGULATION (ppm/V)
5
0
–40
110 125
–10
TEMPERATURE (°C)
20
50
80
110
125
TEMPERATURE (°C)
Figure 15. ADR420 Line Regulation vs. Temperature
Figure 18. ADR425 Line Regulation vs. Temperature
6
2.5
VIN = 5V TO 15V
4
3
2
0
–40
02432-017
1
–10
20
50
80
110
2.0
–40°C
+25°C
1.5
+85°C
1.0
0.5
02432-020
DIFFERENTIAL VOLTAGE (V)
LINE REGULATION (ppm/V)
5
0
125
0
1
TEMPERATURE (°C)
2
3
4
5
LOAD CURRENT (mA)
Figure 16. ADR421 Line Regulation vs. Temperature
Figure 19. ADR420 Minimum Input/Output Voltage
Differential vs. Load Current
2.5
9
VIN = 5V TO 15V
6
5
4
3
2
1
0
–40
–10
20
50
80
2.0
–40°C
+25°C
1.5
+125°C
1.0
0.5
02432-021
DIFFERENTIAL VOLTAGE (V)
7
02432-018
LINE REGULATION (ppm/V)
8
0
0
110
1
2
3
4
LOAD CURRENT (mA)
TEMPERATURE (°C)
Figure 17. ADR423 Line Regulation vs. Temperature
Figure 20. ADR421 Minimum Input/Output Voltage
Differential vs. Load Current
Rev. J | Page 12 of 24
5
Data Sheet
ADR420/ADR421/ADR423/ADR425
2.0
–40°C
1.5
1µV/DIV
+25°C
+125°C
1.0
02432-025
0.5
02432-022
DIFFERENTIAL VOLTAGE (V)
2.5
0
0
1
2
3
4
TIME (1s/DIV)
5
LOAD CURRENT (mA)
Figure 24. ADR421 Typical Noise Voltage 0.1 Hz to 10 Hz
Figure 21. ADR423 Minimum Input/Output Voltage
Differential vs. Load Current
2.0
–40°C
+25°C
50µV/DIV
1.5
+125°C
1.0
02432-026
0.5
02432-023
DIFFERENTIAL VOLTAGE (V)
2.5
0
0
1
2
3
4
TIME (1s/DIV)
5
LOAD CURRENT (mA)
Figure 22. ADR425 Minimum Input/Output Voltage
Differential vs. Load Current
TEMPERATURE
+25°C
–40°C
+125°C
+25°C
1k
SAMPLE SIZE – 160
VOLTAGE NOISE DENSITY (nV/ Hz)
20
15
10
ADR425
ADR423
100
ADR420
10
10
40
50
60
70
80
90
100
110
120
130
MORE
–40
–30
–20
–10
0
10
20
30
0
02432-024
5
–100
–90
–80
–70
–60
–50
NUMBER OF PARTS
25
ADR421
02432-027
30
Figure 25. Typical Noise Voltage 10 Hz to 10 kHz
100
1k
FREQUENCY (Hz)
DEVIATION (ppm)
Figure 26. Voltage Noise Density vs. Frequency
Figure 23. ADR421 Typical Hysteresis
Rev. J | Page 13 of 24
10k
ADR420/ADR421/ADR423/ADR425
Data Sheet
CL = 100nF
CBYPASS = 0µF
1mA LOAD
LINE INTERRUPTION
VOUT
VIN
1V/DIV
500mV/DIV
LOAD OFF
VOUT
500mV/DIV
2V/DIV
02432-028
02432-031
LOAD ON
TIME (100µs/DIV)
TIME (100µs/DIV)
Figure 27. ADR421 Line Transient Response, no CBYPASS
Figure 30. ADR421 Load Transient Response, CL = 100 nF
CIN = 0.01µF
NO LOAD
CBYPASS = 0.1µF
LINE INTERRUPTION
VOUT
VIN
2V/DIV
500mV/DIV
VIN
VOUT
500mV/DIV
02432-029
02432-032
2V/DIV
TIME (4µs/DIV)
TIME (100µs/DIV)
Figure 28. ADR421 Line Transient Response, CBYPASS = 0.1 μF
CL = 0µF
Figure 31. ADR421 Turn-Off Response
CIN = 0.01µF
NO LOAD
1mA LOAD
2V/DIV
VOUT
1V/DIV
VOUT
LOAD OFF
2V/DIV
2V/DIV
LOAD ON
02432-030
02432-033
VIN
TIME (4µs/DIV)
TIME (100µs/DIV)
Figure 32. ADR421 Turn-On Response
Figure 29. ADR421 Load Transient Response, no CL
Rev. J | Page 14 of 24
Data Sheet
ADR420/ADR421/ADR423/ADR425
50
CL = 0.01µF
NO INPUT CAP
45
VOUT
40
OUTPUT IMPEDANCE (Ω)
2V/DIV
VIN
2V/DIV
35
30
ADR425
25
ADR423
20
ADR421
15
5
0
10
TIME (4µs/DIV)
ADR420
100
1k
10k
02432-037
02432-034
10
100k
FREQUENCY (Hz)
Figure 33. ADR421 Turn-Off Response
Figure 36. Output Impedance vs. Frequency
0
CL = 0.01µF
NO INPUT CAP
–10
2V/DIV
RIPPLE REJECTION (dB)
–20
VOUT
2V/DIV
–30
–40
–50
–60
–70
02432-035
02432-038
–80
VIN
–90
–100
10
TIME (4µs/DIV)
100
1k
10k
100k
FREQUENCY (Hz)
Figure 37. Ripple Rejection vs. Frequency
Figure 34. ADR421 Turn-On Response
CBYPASS = 0.1µF
RL = 500Ω
CL = 0
5V/DIV
VIN
2V/DIV
02432-036
VOUT
TIME (100µs/DIV)
Figure 35. ADR421 Turn-On/Turn-Off Response
Rev. J | Page 15 of 24
1M
ADR420/ADR421/ADR423/ADR425
Data Sheet
TERMINOLOGY
Temperature Coefficient
The change of output voltage over the operating temperature
range is normalized by the output voltage at 25°C, and
expressed in ppm/°C as
TCVOUT ppm / C
VOUT T2 VOUT T1
VOUT 25C T2 T1
10 6
VOUT _ HYS VOUT 25C VOUT _ TC
VOUT _ HYS ppm
where:
VOUT (25°C) = VOUT at 25°C.
VOUT (T1) = VOUT at Temperature 1.
VOUT (T2) = VOUT at Temperature 2.
Line Regulation
The change in output voltage due to a specified change in input
voltage. It includes the effects of self-heating. Line regulation is
expressed in either percent per volt, parts per million per volt,
or microvolts per volt change in input voltage.
Load Regulation
The change in output voltage due to a specified change in load
current. It includes the effects of self-heating. Load regulation is
expressed in either microvolts per milliampere, parts per
million per milliampere, or ohms of dc output resistance.
Long-Term Stability
Typical shift of output voltage at 25°C on a sample of parts
subjected to operation life test of 1000 hours at 125°C.
VOUT VOUT t 0 VOUT t 1
VOUT ppm
VOUT t 0 VOUT t 1
VOUT t 0
Thermal Hysteresis
The change of output voltage after the device is cycled through
temperatures from +25°C to −40°C to +125°C and back to
+25°C. This is a typical value from a sample of parts put
through such a cycle.
10 6
where:
VOUT (t0) = VOUT at 25°C at Time 0.
VOUT (t1) = VOUT at 25°C after 1000 hours operation at 125°C.
VOUT 25C VOUT _ TC
VOUT 25C
10 6
where:
VOUT (25°C) = VOUT at 25°C.
VOUT_TC = VOUT at 25°C after temperature cycle at +25°C to
−40°C to +125°C and back to +25°C.
Input Capacitor
Input capacitors are not required on the ADR42x. There is
no limit for the value of the capacitor used on the input, but a
1 μF to 10 μF capacitor on the input improves transient response
in applications where the supply suddenly changes. An additional 0.1 μF capacitor in parallel also helps to reduce noise
from the supply.
Output Capacitor
The ADR42x do not need output capacitors for stability under
any load condition. An output capacitor, typically 0.1 μF, filters
out any low level noise voltage and does not affect the operation
of the part. On the other hand, the load transient response can
be improved with an additional 1 μF to 10 μF output capacitor
in parallel. A capacitor here acts as a source of stored energy for
sudden increase in load current. The only parameter that
degrades by adding an output capacitor is the turn-on time,
which depends on the size of the selected capacitor.
Rev. J | Page 16 of 24
Data Sheet
ADR420/ADR421/ADR423/ADR425
THEORY OF OPERATION
The intrinsic reference voltage is about 0.5 V with a negative
temperature coefficient of about −120 ppm/°C. This slope is
essentially constant to the dielectric constant of silicon and can
be closely compensated by adding a correction term generated
in the same fashion as the proportional-to-temperature (PTAT)
term used to compensate band gap references. The primary
advantage over a band gap reference is that the intrinsic temperature coefficient is approximately 30 times lower (therefore
requiring less correction). This results in much lower noise
because most of the noise of a band gap reference comes from
the temperature compensation circuitry.
Figure 38 shows the basic topology of the ADR42x series. The
temperature correction term is provided by a current source
with a value designed to be proportional to absolute temperature. The general equation is
VOUT = G × (∆VP − R1 × IPTAT)
Each ADR42x device is created by on-chip adjustment of R2
and R3 to achieve the specified reference output.
VIN
I1
ADR420/ADR421/
ADR423/ADR425
IPTAT
VOUT
R2
TJ = PD × θJA + TA
*EXTRA CHANNEL IMPLANT
VOUT = G(ΔVP – R1 × IPTAT)
Figure 38. Simplified Schematic
R3
GND
02432-039
R1
(2)
where:
TJ and TA are the junction temperature and the ambient
temperature, respectively.
PD is the device power dissipation.
θJA is the device package thermal resistance.
BASIC VOLTAGE REFERENCE CONNECTIONS
Voltage references, in general, require a bypass capacitor
connected from VOUT to GND. The circuit in Figure 39
illustrates the basic configuration for the ADR42x family of
references. Other than a 0.1 µF capacitor at the output to help
improve noise suppression, a large output capacitor at the
output is not required for circuit stability.
TP 1
VIN
10µF
+
2
0.1µF
NIC 3
4
ADR420/
ADR421/
ADR423/
ADR425
8
TP
7
NIC
OUTPUT
6
TOP VIEW
(Not to Scale) 5 TRIM
0.1µF
NIC = NO INTERNAL CONNECTION
TP = TEST PIN (DO NOT CONNECT)
Figure 39. Basic Voltage Reference Configuration
NOISE PERFORMANCE
The noise generated by ADR42x references is typically less
than 2 µV p-p over the 0.1 Hz to 10 Hz band for the ADR420,
ADR421, and ADR423. Figure 24 shows the 0.1 Hz to 10 Hz
noise of the ADR421, which is only 1.75 µV p-p. The noise
measurement is made with a band-pass filter made of a 2-pole
high-pass filter with a corner frequency at 0.1 Hz and a 2-pole
low-pass filter with a corner frequency at 10 Hz.
TURN-ON TIME
*
ΔVP
The ADR42x family of references is guaranteed to deliver load
currents to 10 mA with an input voltage that ranges from 4.5 V
to 18 V. When these devices are used in applications at higher
currents, the following equation should be used to account for
the temperature effects due to power dissipation increases:
(1)
where:
G is the gain of the reciprocal of the divider ratio.
∆VP is the difference in pinch-off voltage between the two JFETs.
IPTAT is the positive temperature coefficient correction current.
I1
DEVICE POWER DISSIPATION CONSIDERATIONS
02432-040
The ADR42x series of references uses a reference generation
technique known as XFET (eXtra implanted junction FET).
This technique yields a reference with low supply current, good
thermal hysteresis, and exceptionally low noise. The core of the
XFET reference consists of two junction field-effect transistors
(JFET), one having an extra channel implant to raise its pinchoff voltage. By running the two JFETs at the same drain current,
the difference in pinch-off voltage can be amplified and used to
form a highly stable voltage reference.
At power-up (cold start), the time required for the output
voltage to reach its final value within a specified error band
is defined as the turn-on settling time. Two components typically associated with this are the time for the active circuits to
settle and the time for the thermal gradients on the chip to
stabilize. Figure 31 to Figure 35 show the turn-on settling time
for the ADR421.
Rev. J | Page 17 of 24
ADR420/ADR421/ADR423/ADR425
Data Sheet
APPLICATIONS
OUTPUT ADJUSTMENT
SOURCE FIBER
GIMBAL + SENSOR
The ADR42x trim terminal can be used to adjust the output
voltage over a ±0.5% range. This feature allows the system
designer to trim system errors out by setting the reference to
a voltage other than the nominal. This is also helpful if the
part is used in a system at temperature to trim out any error.
Adjustment of the output has a negligible effect on the
temperature performance of the device. To avoid degrading
temperature coefficients, both the trimming potentiometer
and the two resistors need to be low temperature coefficient
types, preferably
工商网监
湘ICP备2023018690号
