SHARC Processor
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
SUMMARY
KEY FEATURES—PROCESSOR CORE
High performance signal processor for communications,
graphics and imaging applications
Super Harvard Architecture
4 independent buses for dual data fetch, instruction fetch,
and nonintrusive I/O
32-bit IEEE floating-point computation units—multiplier,
ALU, and shifter
Dual-ported on-chip SRAM and integrated I/O peripherals—a
complete system-on-a-chip
Integrated multiprocessing features
240-lead thermally enhanced MQFP_PQ4 package, 225-ball
plastic ball grid array (PBGA), 240-lead hermetic CQFP
package
RoHS compliant packages
40 MIPS, 25 ns instruction rate, single-cycle instruction
execution
120 MFLOPS peak, 80 MFLOPS sustained performance
Dual data address generators with modulo and bit-reverse
addressing)
Efficient program sequencing with zero-overhead looping:
Single-cycle loop setup
IEEE JTAG Standard 1149.1 Test Access Port and on-chip
emulation
32-bit single-precision and 40-bit extended-precision IEEE
floating-point data formats or 32-bit fixed-point data
format
CORE PROCESSOR
DAG1
8 4 32
TWO INDEPENDENT
DUAL-PORTED BLOCKS
PROCESSOR PORT
I/O PORT
ADDR
DATA
ADDR
DATA
DATA
ADDR
ADDR
DATA
DAG2
8 4 24
JTAG
BLOCK 1
INSTRUCTION
CACHE
32 48-BIT
B LOCK 0
TIMER
DUAL-PORTED SRAM
PROGRAM
SEQUENCER
PM ADDRESS BUS
DM ADDRESS BUS
IOD
48
24
IOA
17
EXTERNAL
PORT
ADDR BUS
MUX
32
7
TEST AND
EMULATION
32
MULTIPROCESSOR
INTERFACE
PM DATA BUS
BUS
CONNECT
(PX)
DM DATA BUS
48
DATA BUS
MUX
40/32
S
DATA
REGISTER
FILE
MULT
16 40-BIT
BARREL
SHIFTER
HOST PORT
DMA
CONTROLLER
IOP
REGISTERS
(MEMORY
MAPPED)
ALU
48
4
6
CONTROL,
STATUS AND
DATA BUFFERS
SERIAL PORTS
(2)
LINK PORTS
(6)
6
36
I/O PROCESSOR
Figure 1. Functional Block Diagram
SHARC and the SHARC logo are registered trademarks of Analog Devices, Inc.
Rev. H
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 U.S.A.
Tel: 781.329.4700
©2013 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
PARALLEL COMPUTATIONS
Single-cycle multiply and ALU operations in parallel with
dual memory read/writes and instruction fetch
Multiply with add and subtract for accelerated FFT butterfly
computation
UP TO 4M BIT ON-CHIP SRAM
HOST PROCESSOR INTERFACE TO 16- AND 32-BIT
MICROPROCESSORS
Host can directly read/write ADSP-2106x internal memory
and IOP registers
MULTIPROCESSING
Glueless connection for scalable DSP multiprocessing
architecture
Distributed on-chip bus arbitration for parallel bus connect
of up to six ADSP-2106xs plus host
Six link ports for point-to-point connectivity and array
multiprocessing
240 MBps transfer rate over parallel bus
240 MBps transfer rate over link ports
Dual-ported for independent access by core processor and
DMA
OFF-CHIP MEMORY INTERFACING
4 gigawords addressable
Programmable wait state generation, page-mode DRAM
support
DMA CONTROLLER
SERIAL PORTS
10 DMA channels for transfers between ADSP-2106x internal
memory and external memory, external peripherals, host
processor, serial ports, or link ports
Background DMA transfers at up to 40 MHz, in parallel with
full-speed processor execution
Two 40 Mbps synchronous serial ports with companding
hardware
Independent transmit and receive functions
Table 1. ADSP-2106x SHARC Processor Family Features
Feature
ADSP-21060
ADSP-21062
ADSP-21060L
ADSP-21062L
ADSP-21060C
ADSP-21060LC
SRAM
4M bits
2M bits
4M bits
2M bits
4M bits
4M bits
Operating
Voltage
5V
5V
3.3 V
3.3 V
5V
3.3 V
Instruction
Rate
33 MHz
40 MHz
33 MHz
40 MHz
33 MHz
40 MHz
33 MHz
40 MHz
33 MHz
40 MHz
33 MHz
40 MHz
Package
MQFP_PQ4
PBGA
MQFP_PQ4
PBGA
MQFP_PQ4
PBGA
MQFP_PQ4
PBGA
CQFP
CQFP
Rev. H |
Page 2 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
CONTENTS
Summary ............................................................... 1
Electrical Characteristics (3.3 V) ............................. 18
General Description ................................................. 4
Internal Power Dissipation (3.3 V) .......................... 19
SHARC Family Core Architecture ............................ 4
External Power Dissipation (3.3 V) .......................... 20
Memory and I/O Interface Features ........................... 5
Absolute Maximum Ratings ................................... 20
Development Tools ............................................... 8
ESD Caution ...................................................... 21
Additional Information .......................................... 9
Package Marking Information ................................ 21
Related Signal Chains ............................................ 9
Timing Specifications ........................................... 21
Pin Function Descriptions ........................................ 10
Test Conditions .................................................. 48
Target Board Connector for EZ-ICE Probe ................ 13
Environmental Conditions .................................... 51
ADSP-21060/ADSP-21062 Specifications ..................... 15
225-Ball PBGA Ball Configuration .............................. 52
Operating Conditions (5 V) .................................... 15
240-Lead MQFP_PQ4/CQFP Pin Configuration ............ 54
Electrical Characteristics (5 V) ................................ 15
Outline Dimensions ................................................ 56
Internal Power Dissipation (5 V) ............................. 16
Surface-Mount Design .......................................... 61
External Power Dissipation (5 V) ............................. 17
Ordering Guide ..................................................... 62
ADSP-21060L/ADSP-21062L Specifications .................. 18
Operating Conditions (3.3 V) ................................. 18
REVISION HISTORY
3/13—Rev. G to Rev. H
Updated Development Tools .......................................8
Corrected the power dissipation equation from PTOTAL = PEXT +
(IDDIN2 5.0 V) to PTOTAL = PEXT + (IDDIN2 3.3 V)
External Power Dissipation (3.3 V) ............................. 20
Rev. H |
Page 3 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
GENERAL DESCRIPTION
The ADSP-2106x SHARC®—Super Harvard Architecture Computer—is a 32-bit signal processing microcomputer that offers
high levels of DSP performance. The ADSP-2106x builds on the
ADSP-21000 DSP core to form a complete system-on-a-chip,
adding a dual-ported on-chip SRAM and integrated I/O peripherals supported by a dedicated I/O bus.
• Serial ports and link ports
• JTAG Test Access Port
ADSP-2106x
4
The ADSP-2106x SHARC represents a new standard of integration for signal computers, combining a high performance
floating-point DSP core with integrated, on-chip system features including up to 4M bit SRAM memory (see Table 1), a
host processor interface, DMA controller, serial ports and link
port, and parallel bus connectivity for glueless DSP
multiprocessing.
LINK
DEVICES
(6 MAX)
(OPTIONAL)
Table 2. Benchmarks (at 40 MHz)
Benchmark Algorithm
1024 Point Complex FFT (Radix 4, with
reversal)
FIR Filter (per tap)
IIR Filter (per biquad)
Divide (y/x)
Inverse Square Root
DMA Transfer Rate
Speed
0.46 s
25 ns
100 ns
150 ns
225 ns
240 Mbytes/s
EBOOT
ADDR
LBOOT
DATA
FLAG3–0
ADDR31–0
ADDR
TIMEXP
DATA47–0
DATA MEMORYMAPPED
OE
DEVICES
WE
(OPTIONAL)
ACK
LxCLK
LxACK
LxDAT3–0
SERIAL
DEVICE
(OPTIONAL)
TCLK0
RCLK0
TFS0
RSF0
DT0
DR0
SERIAL
DEVICE
(OPTIONAL)
TCLK1
RCLK1
TFS1
RSF1
DT1
DR1
Cycles
18,221
RPBA
ID2–0
RESET
1
4
6
9
BOOT
EPROM
(OPTIONAL)
IRQ2–0
RD
WR
ACK
CS
MS3–0
PAGE
SBTS
ADRCLK
DMAR1–2
DATA
3
CS
BMS
ADDRESS
Fabricated in a high speed, low power CMOS process, the
ADSP-2106x has a 25 ns instruction cycle time and operates at
40 MIPS. With its on-chip instruction cache, the processor can
execute every instruction in a single cycle. Table 2 shows performance benchmarks for the ADSP-2106x.
CLKIN
CONTROL
1 ⫻ CLOCK
DMA DEVICE
(OPTIONAL)
DATA
DMAG1–2
CS
HBR
HBG
REDY
HOST
PROCESSOR
INTERFACE
(OPTIONAL)
BR1–6
ADDR
PA
DATA
JTAG
6
Figure 2. ADSP-2106x System Sample Configuration
SHARC FAMILY CORE ARCHITECTURE
The ADSP-2106x continues SHARC’s industry-leading standards of integration for DSPs, combining a high performance
32-bit DSP core with integrated, on-chip system features.
The block diagram on Page 1 illustrates the following architectural features:
• Computation units (ALU, multiplier and shifter) with a
shared data register file
• Data address generators (DAG1, DAG2)
• Program sequencer with instruction cache
• PM and DM buses capable of supporting four 32-bit data
transfers between memory and the core at every core processor cycle
• Interval timer
• On-chip SRAM
• External port for interfacing to off-chip memory and
peripherals
• Host port and multiprocessor Interface
The ADSP-2106x includes the following architectural features
of the ADSP-21000 family core.
Independent, Parallel Computation Units
The arithmetic/logic unit (ALU), multiplier and shifter all perform single-cycle instructions. The three units are arranged in
parallel, maximizing computational throughput. Single multifunction instructions execute parallel ALU and multiplier operations. These computation units support IEEE 32-bit singleprecision floating-point, extended precision 40-bit floatingpoint, and 32-bit fixed-point data formats.
Data Register File
A general–purpose data register file is used for transferring data
between the computation units and the data buses, and for storing intermediate results. This 10-port, 32-register (16 primary,
16 secondary) register file, combined with the ADSP-21000
Harvard architecture, allows unconstrained data flow between
computation units and internal memory.
• DMA controller
Rev. H |
Page 4 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Single-Cycle Fetch of Instruction and Two Operands
The ADSP-2106x features an enhanced Harvard architecture in
which the data memory (DM) bus transfers data and the program memory (PM) bus transfers both instructions and data
(see Figure 1 on Page 1). With its separate program and data
memory buses and on-chip instruction cache, the processor can
simultaneously fetch two operands and an instruction (from the
cache), all in a single cycle.
Instruction Cache
The ADSP-2106x includes an on-chip instruction cache that
enables three-bus operation for fetching an instruction and two
data values. The cache is selective—only the instructions whose
fetches conflict with PM bus data accesses are cached. This
allows full-speed execution of core, looped operations such as
digital filter multiply-accumulates and FFT butterfly processing.
Data Address Generators with Hardware Circular Buffers
The ADSP-2106x’s two data address generators (DAGs) implement circular data buffers in hardware. Circular buffers allow
efficient programming of delay lines and other data structures
required in digital signal processing, and are commonly used in
digital filters and Fourier transforms. The two DAGs of the
ADSP-2106x contain sufficient registers to allow the creation of
up to 32 circular buffers (16 primary register sets, 16 secondary).
The DAGs automatically handle address pointer wraparound,
reducing overhead, increasing performance and simplifying
implementation. Circular buffers can start and end at any memory location.
Flexible Instruction Set
The 48-bit instruction word accommodates a variety of
parallel operations, for concise programming. For example, the
ADSP-2106x can conditionally execute a multiply, an add, a
subtract and a branch, all in a single instruction.
MEMORY AND I/O INTERFACE FEATURES
The ADSP-2106x processors add the following architectural
features to the SHARC family core.
A 16-bit floating-point storage format is supported, which effectively doubles the amount of data that can be stored on-chip.
Conversion between the 32-bit floating-point and 16-bit floating-point formats is done in a single instruction.
While each memory block can store combinations of code and
data, accesses are most efficient when one block stores data,
using the DM bus for transfers, and the other block stores
instructions and data, using the PM bus for transfers. Using the
DM bus and PM bus in this way, with one dedicated to each
memory block, assures single-cycle execution with two data
transfers. In this case, the instruction must be available in the
cache. Single-cycle execution is also maintained when one of the
data operands is transferred to or from off-chip, via the
ADSP-2106x’s external port.
On-Chip Memory and Peripherals Interface
The ADSP-2106x’s external port provides the processor’s interface to off-chip memory and peripherals. The 4-gigaword offchip address space is included in the ADSP-2106x’s unified
address space. The separate on-chip buses—for PM addresses,
PM data, DM addresses, DM data, I/O addresses, and I/O
data—are multiplexed at the external port to create an external
system bus with a single 32-bit address bus and a single 48-bit
(or 32-bit) data bus.
Addressing of external memory devices is facilitated by on-chip
decoding of high-order address lines to generate memory bank
select signals. Separate control lines are also generated for simplified addressing of page-mode DRAM. The ADSP-2106x
provides programmable memory wait states and external memory acknowledge controls to allow interfacing to DRAM and
peripherals with variable access, hold and disable time
requirements.
Host Processor Interface
Dual-Ported On-Chip Memory
The ADSP-21062/ADSP-21062L contains two megabits of onchip SRAM, and the ADSP-21060/ADSP-21060L contains
4M bits of on-chip SRAM. The internal memory is organized as
two equal sized blocks of 1M bit each for the ADSP-21062/
ADSP-21062L and two equal sized blocks of 2M bits each for
the ADSP-21060/ADSP-21060L. Each can be configured for different combinations of code and data storage. Each memory
block is dual-ported for single-cycle, independent accesses by
the core processor and I/O processor or DMA controller. The
dual-ported memory and separate on-chip buses allow two data
transfers from the core and one from I/O, all in a single cycle.
On the ADSP-21062/ADSP-21062L, the memory can be configured as a maximum of 64k words of 32-bit data, 128k words of
16-bit data, 40k words of 48-bit instructions (or 40-bit data), or
combinations of different word sizes up to two megabits. All of
the memory can be accessed as 16-bit, 32-bit, or 48-bit words.
Rev. H |
On the ADSP-21060/ADSP-21060L, the memory can be configured as a maximum of 128k words of 32-bit data, 256k words of
16-bit data, 80k words of 48-bit instructions (or 40-bit data), or
combinations of different word sizes up to four megabits. All of
the memory can be accessed as 16-bit, 32-bit or 48-bit words.
The ADSP-2106x’s host interface allows easy connection to
standard microprocessor buses, both 16-bit and 32-bit, with little additional hardware required. Asynchronous transfers at
speeds up to the full clock rate of the processor are supported.
The host interface is accessed through the ADSP-2106x’s external port and is memory-mapped into the unified address space.
Four channels of DMA are available for the host interface; code
and data transfers are accomplished with low software
overhead.
The host processor requests the ADSP-2106x’s external bus with
the host bus request (HBR), host bus grant (HBG), and ready
(REDY) signals. The host can directly read and write the internal memory of the ADSP-2106x, and can access the DMA
channel setup and mailbox registers. Vector interrupt support is
provided for efficient execution of host commands.
Page 5 of 64 |
March 2013
ADDRESS
DATA
DATA
RESET
ADDRESS
ADSP-2106x #3
CLKIN
CONTROL
ADSP-2106x #6
ADSP-2106x #5
ADSP-2106x #4
CONTROL
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
ADDR31–0
DATA47–0
RPBA
3
ID2–0
CONTROL
011
BR1–2, BR4–6
5
BR3
ADSP-2106x #2
CLKIN
ADDR31–0
RESET
DATA47–0
RPBA
3
ID2–0
CONTROL
010
CPA
BR1, BR3–6
BR2
5
ADSP-2106x #1
CLKIN
RESET
ADDR
DATA47–0
DATA
RDx
ID2–0
WRx
ACK
MS3–0
CONTROL
RPBA
3
001
ADDR31–0
OE
WE
ACK
CS
BMS
PAGE
CS
ADDR
SBTS
BUS
PRIORITY
RESET
CLOCK
GLOBAL MEMORY
AND
PERIPHERAL (OPTIONAL)
BOOT EPROM (OPTIONAL)
DATA
CS
HBR
HBG
REDY
CPA
BR2–6
BR1
HOST PROCESSOR
INTERFACE (OPTIONAL)
ADDR
5
DATA
Figure 3. Shared Memory Multiprocessing System
Rev. H |
Page 6 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
control two DMA channels using DMA request/grant lines
(DMAR1–2, DMAG1–2). Other DMA features include interrupt generation upon completion of DMA transfers and DMA
chaining for automatic linked DMA transfers.
DMA Controller
The ADSP-2106x’s on-chip DMA controller allows zero-overhead data transfers without processor intervention. The DMA
controller operates independently and invisibly to the processor
core, allowing DMA operations to occur while the core is simultaneously executing its program instructions.
Multiprocessing
The ADSP-2106x offers powerful features tailored to multiprocessor DSP systems. The unified address space (see Figure 4)
allows direct interprocessor accesses of each ADSP-2106x’s
internal memory. Distributed bus arbitration logic is included
on-chip for simple, glueless connection of systems containing
up to six ADSP-2106xs and a host processor. Master processor
changeover incurs only one cycle of overhead. Bus arbitration is
selectable as either fixed or rotating priority. Bus lock allows
indivisible read-modify-write sequences for semaphores. A vector interrupt is provided for interprocessor commands. Maximum throughput for interprocessor data transfer is
240M bytes/s over the link ports or external port. Broadcast
writes allow simultaneous transmission of data to all
ADSP-2106xs and can be used to implement reflective
semaphores.
DMA transfers can occur between the ADSP-2106x’s internal
memory and external memory, external peripherals, or a host
processor. DMA transfers can also occur between the ADSP2106x’s internal memory and its serial ports or link ports. DMA
transfers between external memory and external peripheral
devices are another option. External bus packing to 16-,
32-, or 48-bit words is performed during DMA transfers.
Ten channels of DMA are available on the ADSP-2106x—two
via the link ports, four via the serial ports, and four via the
processor’s external port (for either host processor, other
ADSP-2106xs, memory, or I/O transfers). Four additional link
port DMA channels are shared with Serial Port 1 and the external port. Programs can be downloaded to the ADSP-2106x
using DMA transfers. Asynchronous off-chip peripherals can
ADDRESS
ADDRESS
0x0000 0000
0x0040 0000
IOP REGISTERS
INTERNAL
MEMORY
SPACE
NORMAL WORD ADDRESSING
(32-BIT DATA WORDS
48-BIT INSTRUCTION WORDS)
0x0002 0000
BANK 0
0x0004 0000
MS0
SRAM
(OPTIONAL)
SHORT WORD ADDRESSING
(16-BIT DATA WORDS)
0x0008 0000
INTERNAL MEMORY SPACE
WITH ID = 001
BANK 1
MS1
BANK 2
MS2
BANK 3
MS3
0x0010 0000
INTERNAL MEMORY SPACE
WITH ID = 010
0x0018 0000
MULTIPROCESSOR
MEMORY
SPACE
EXTERNAL
MEMORY
SPACE
INTERNAL MEMORY SPACE
WITH ID = 011
0x0012 0000
INTERNAL MEMORY SPACE
WITH ID = 100
0x0028 0000
INTERNAL MEMORY SPACE
WITH ID = 101
0x0030 0000
INTERNAL MEMORY SPACE
WITH ID = 110
0x0038 0000
BROADCAST WRITE
TO ALL ADSP-21061s
NONBANKED
0x003F FFFF
0x0FFF FFFF
NOTE: BANK SIZES ARE SELECTED BY
MSIZE BITS IN THE SYSCON REGISTER
Figure 4. Memory Map
Rev. H |
Page 7 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Link Ports
The ADSP-2106x features six 4-bit link ports that provide additional I/O capabilities. The link ports can be clocked twice per
cycle, allowing each to transfer eight bits of data per cycle. Linkport I/O is especially useful for point-to-point interprocessor
communication in multiprocessing systems.
The link ports can operate independently and simultaneously,
with a maximum data throughput of 240M bytes/s. Link port
data is packed into 32- or 48-bit words, and can be directly read
by the core processor or DMA-transferred to on-chip memory.
Each link port has its own double-buffered input and output
registers. Clock/acknowledge handshaking controls link port
transfers. Transfers are programmable as either transmit or
receive.
Program Booting
The internal memory of the ADSP-2106x can be booted at system power-up from an 8-bit EPROM, a host processor, or
through one of the link ports. Selection of the boot source is
controlled by the BMS (boot memory select), EBOOT (EPROM
Boot), and LBOOT (link/host boot) pins. 32-bit and 16-bit host
processors can be used for booting. The processor also supports a no-boot mode in which instruction execution is sourced
from the external memory.
DEVELOPMENT TOOLS
Analog Devices supports its processors with a complete line of
software and hardware development tools, including integrated
development environments (which include CrossCore® Embedded Studio and/or VisualDSP++®), evaluation products,
emulators, and a wide variety of software add-ins.
Integrated Development Environments (IDEs)
For C/C++ software writing and editing, code generation, and
debug support, Analog Devices offers two IDEs.
The newest IDE, CrossCore Embedded Studio, is based on the
EclipseTM framework. Supporting most Analog Devices processor families, it is the IDE of choice for future processors,
including multicore devices. CrossCore Embedded Studio
seamlessly integrates available software add-ins to support real
time operating systems, file systems, TCP/IP stacks, USB stacks,
algorithmic software modules, and evaluation hardware board
support packages. For more information visit
www.analog.com/cces.
The other Analog Devices IDE, VisualDSP++, supports processor families introduced prior to the release of CrossCore
Embedded Studio. This IDE includes the Analog Devices VDK
real time operating system and an open source TCP/IP stack.
For more information visit www.analog.com/visualdsp. Note
that VisualDSP++ will not support future Analog Devices
processors.
emulation capabilities and other evaluation and development
features. Also available are various EZ-Extenders®, which are
daughter cards delivering additional specialized functionality,
including audio and video processing. For more information
visit www.analog.com and search on “ezkit” or “ezextender”.
EZ-KIT Lite Evaluation Kits
For a cost-effective way to learn more about developing with
Analog Devices processors, Analog Devices offer a range of EZKIT Lite evaluation kits. Each evaluation kit includes an EZ-KIT
Lite evaluation board, directions for downloading an evaluation
version of the available IDE(s), a USB cable, and a power supply.
The USB controller on the EZ-KIT Lite board connects to the
USB port of the user’s PC, enabling the chosen IDE evaluation
suite to emulate the on-board processor in-circuit. This permits
the customer to download, execute, and debug programs for the
EZ-KIT Lite system. It also supports in-circuit programming of
the on-board Flash device to store user-specific boot code,
enabling standalone operation. With the full version of CrossCore Embedded Studio or VisualDSP++ installed (sold
separately), engineers can develop software for supported EZKITs or any custom system utilizing supported Analog Devices
processors.
Software Add-Ins for CrossCore Embedded Studio
Analog Devices offers software add-ins which seamlessly integrate with CrossCore Embedded Studio to extend its capabilities
and reduce development time. Add-ins include board support
packages for evaluation hardware, various middleware packages, and algorithmic modules. Documentation, help,
configuration dialogs, and coding examples present in these
add-ins are viewable through the CrossCore Embedded Studio
IDE once the add-in is installed.
Board Support Packages for Evaluation Hardware
Software support for the EZ-KIT Lite evaluation boards and EZExtender daughter cards is provided by software add-ins called
Board Support Packages (BSPs). The BSPs contain the required
drivers, pertinent release notes, and select example code for the
given evaluation hardware. A download link for a specific BSP is
located on the web page for the associated EZ-KIT or EZExtender product. The link is found in the Product Download
area of the product web page.
Middleware Packages
Analog Devices separately offers middleware add-ins such as
real time operating systems, file systems, USB stacks, and
TCP/IP stacks. For more information see the following web
pages:
• www.analog.com/ucos3
• www.analog.com/ucfs
• www.analog.com/ucusbd
• www.analog.com/lwip
EZ-KIT Lite Evaluation Board
For processor evaluation, Analog Devices provides wide range
of EZ-KIT Lite® evaluation boards. Including the processor and
key peripherals, the evaluation board also supports on-chip
Rev. H |
Page 8 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Algorithmic Modules
To speed development, Analog Devices offers add-ins that perform popular audio and video processing algorithms. These are
available for use with both CrossCore Embedded Studio and
VisualDSP++. For more information visit www.analog.com
and search on “Blackfin software modules” or “SHARC software
modules”.
The Application Signal Chains page in the Circuits from the
LabTM site (http://www.analog.com/signalchains) provides:
• Graphical circuit block diagram presentation of signal
chains for a variety of circuit types and applications
• Drill down links for components in each chain to selection
guides and application information
• Reference designs applying best practice design techniques
Designing an Emulator-Compatible DSP Board (Target)
For embedded system test and debug, Analog Devices provides
a family of emulators. On each JTAG DSP, Analog Devices supplies an IEEE 1149.1 JTAG Test Access Port (TAP). In-circuit
emulation is facilitated by use of this JTAG interface. The emulator accesses the processor’s internal features via the
processor’s TAP, allowing the developer to load code, set breakpoints, and view variables, memory, and registers. The
processor must be halted to send data and commands, but once
an operation is completed by the emulator, the DSP system is set
to run at full speed with no impact on system timing. The emulators require the target board to include a header that supports
connection of the DSP’s JTAG port to the emulator.
For details on target board design issues including mechanical
layout, single processor connections, signal buffering, signal termination, and emulator pod logic, see the EE-68: Analog Devices
JTAG Emulation Technical Reference on the Analog Devices
website (www.analog.com)—use site search on “EE-68.” This
document is updated regularly to keep pace with improvements
to emulator support.
ADDITIONAL INFORMATION
This data sheet provides a general overview of the ADSP-2106x
architecture and functionality. For detailed information on the
ADSP-21000 family core architecture and instruction set, refer
to the ADSP-2106x SHARC User’s Manual, Revision 2.1.
RELATED SIGNAL CHAINS
A signal chain is a series of signal-conditioning electronic components that receive input (data acquired from sampling either
real-time phenomena or from stored data) in tandem, with the
output of one portion of the chain supplying input to the next.
Signal chains are often used in signal processing applications to
gather and process data or to apply system controls based on
analysis of real-time phenomena. For more information about
this term and related topics, see the “signal chain” entry in the
Glossary of EE Terms on the Analog Devices website.
Analog Devices eases signal processing system development by
providing signal processing components that are designed to
work together well. A tool for viewing relationships between
specific applications and related components is available on the
www.analog.com website.
Rev. H |
Page 9 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
PIN FUNCTION DESCRIPTIONS
The ADSP-2106x pin definitions are listed below. Inputs identified as synchronous (S) must meet timing requirements with
respect to CLKIN (or with respect to TCK for TMS, TDI).
Inputs identified as asynchronous (A) can be asserted asynchronously to CLKIN (or to TCK for TRST).
Unused inputs should be tied or pulled to VDD or GND, except
for ADDR31–0, DATA47–0, FLAG3–0, and inputs that have
internal pull-up or pull-down resistors (CPA, ACK, DTx, DRx,
TCLKx, RCLKx, LxDAT3–0, LxCLK, LxACK, TMS, and
TDI)—these pins can be left floating. These pins have a
logic-level hold circuit that prevents the input from floating
internally.
Table 3. Pin Descriptions
Pin
ADDR31–0
Type
I/O/T
Function
External Bus Address. The ADSP-2106x outputs addresses for external memory and peripherals on these
pins. In a multiprocessor system, the bus master outputs addresses for read/write of the internal memory
or IOP registers of other ADSP-2106xs. The ADSP-2106x inputs addresses when a host processor or multiprocessing bus master is reading or writing its internal memory or IOP registers.
DATA47–0
I/O/T
External Bus Data. The ADSP-2106x inputs and outputs data and instructions on these pins. 32-bit singleprecision floating-point data and 32-bit fixed-point data is transferred over bits 47–16 of the bus. 40-bit
extended-precision floating-point data is transferred over bits 47–8 of the bus. 16-bit short word data is
transferred over bits 31–16 of the bus. In PROM boot mode, 8-bit data is transferred over bits 23–16. Pull-up
resistors on unused DATA pins are not necessary.
O/T
Memory Select Lines. These lines are asserted (low) as chip selects for the corresponding banks of external
MS3–0
memory. Memory bank size must be defined in the ADSP-2106x’s system control register (SYSCON). The
MS3–0 lines are decoded memory address lines that change at the same time as the other address lines.
When no external memory access is occurring, the MS3–0 lines are inactive; they are active however when
a conditional memory access instruction is executed, whether or not the condition is true. MS0 can be used
with the PAGE signal to implement a bank of DRAM memory (Bank 0). In a multiprocessing system the MS3–0
lines are output by the bus master.
RD
I/O/T
Memory Read Strobe. This pin is asserted (low) when the ADSP-2106x reads from external memory devices
or from the internal memory of other ADSP-2106xs. External devices (including other ADSP-2106xs) must
assert RD to read from the ADSP-2106x’s internal memory. In a multiprocessing system, RD is output by the
bus master and is input by all other ADSP-2106xs.
I/O/T
Memory Write Strobe. This pin is asserted (low) when the ADSP-2106x writes to external memory devices
WR
or to the internal memory of other ADSP-2106xs. External devices must assert WR to write to the ADSP2106x’s internal memory. In a multiprocessing system, WR is output by the bus master and is input by all
other ADSP-2106xs.
PAGE
O/T
DRAM Page Boundary. The ADSP-2106x asserts this pin to signal that an external DRAM page boundary
has been crossed. DRAM page size must be defined in the ADSP-2106x’s memory control register (WAIT).
DRAM can only be implemented in external memory Bank 0; the PAGE signal can only be activated for Bank
0 accesses. In a multiprocessing system, PAGE is output by the bus master
ADRCLK
O/T
Clock Output Reference. In a multiprocessing system, ADRCLK is output by the bus master.
SW
I/O/T
Synchronous Write Select. This signal is used to interface the ADSP-2106x to synchronous memory devices
(including other ADSP-2106xs). The ADSP-2106x asserts SW (low) to provide an early indication of an
impending write cycle, which can be aborted if WR is not later asserted (e.g., in a conditional write
instruction). In a multiprocessing system, SW is output by the bus master and is input by all other
ADSP-2106xs to determine if the multiprocessor memory access is a read or write. SW is asserted at the same
time as the address output. A host processor using synchronous writes must assert this pin when writing to
the ADSP-2106x(s).
A = Asynchronous, G = Ground, I = Input, O = Output, P = Power Supply, S = Synchronous, (A/D) = Active Drive, (O/D) = Open Drain,
T = Three-State (when SBTS is asserted, or when the ADSP-2106x is a bus slave)
Rev. H |
Page 10 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Table 3. Pin Descriptions (Continued)
Pin
ACK
Type
I/O/S
Function
Memory Acknowledge. External devices can deassert ACK (low) to add wait states to an external memory
access. ACK is used by I/O devices, memory controllers, or other peripherals to hold off completion of an
external memory access. The ADSP-2106x deasserts ACK as an output to add waitstates to a synchronous
access of its internal memory. In a multiprocessing system, a slave ADSP-2106x deasserts the bus master’s
ACK input to add wait state(s) to an access of its internal memory. The bus master has a keeper latch on its
ACK pin that maintains the input at the level to which it was last driven.
I/S
Suspend Bus Three-State. External devices can assert SBTS (low) to place the external bus address, data,
SBTS
selects, and strobes in a high impedance state for the following cycle. If the ADSP-2106x attempts to access
external memory while SBTS is asserted, the processor will halt and the memory access will not be completed
until SBTS is deasserted. SBTS should only be used to recover from host processor/ADSP-2106x deadlock,
or used with a DRAM controller.
IRQ2–0
I/A
Interrupt Request Lines. May be either edge-triggered or level-sensitive.
FLAG3–0
I/O/A
Flag Pins. Each is configured via control bits as either an input or output. As an input, they can be tested as
a condition. As an output, they can be used to signal external peripherals.
TIMEXP
O
Timer Expired. Asserted for four cycles when the timer is enabled and TCOUNT decrements to zero.
HBR
I/A
Host Bus Request. This pin must be asserted by a host processor to request control of the ADSP-2106x’s
external bus. When HBR is asserted in a multiprocessing system, the ADSP-2106x that is bus master will
relinquish the bus and assert HBG. To relinquish the bus, the ADSP-2106x places the address, data, select
and strobe lines in a high impedance state. HBR has priority over all ADSP-2106x bus requests BR6–1 in a
multiprocessing system.
HBG
I/O
Host Bus Grant. Acknowledges a bus request, indicating that the host processor may take control of the
external bus. HBG is asserted (held low) by the ADSP-2106x until HBR is released. In a multiprocessing system,
HBG is output by the ADSP-2106x bus master and is monitored by all others.
CS
I/A
Chip Select. Asserted by host processor to select the ADSP-2106x.
REDY
O (O/D)
Host Bus Acknowledge. The ADSP-2106x deasserts REDY (low) to add wait states to an asynchronous access
of its internal memory or IOP registers by a host. This pin is an open-drain output (O/D) by default; it can be
programmed in the ADREDY bit of the SYSCON register to be active drive (A/D). REDY will only be output if
the CS and HBR inputs are asserted.
DMAR2–1
I/A
DMA Request 1 (DMA Channel 7) and DMA Request 2 (DMA Channel 8).
DMAG2–1
O/T
DMA Grant 1 (DMA Channel 7) and DMA Grant 2 (DMA Channel 8).
BR6–1
I/O/S
Multiprocessing Bus Requests. Used by multiprocessing ADSP-2106xs to arbitrate for bus master-ship. An
ADSP-2106x only drives its own BRx line (corresponding to the value of its ID2-0 inputs) and monitors all
others. In a multiprocessor system with less than six ADSP-2106xs, the unused BRx pins should be pulled
high; the processor’s own BRx line must not be pulled high or low because it is an output.
ID2–0
O (O/D)
Multiprocessing ID. Determines which multiprocessing bus request (BR1– BR6) is used by ADSP-2106x.
ID = 001 corresponds to BR1, ID = 010 corresponds to BR2, etc. ID = 000 in single-processor systems. These
lines are a system configuration selection that should be hardwired or changed at reset only.
RPBA
I/S
Rotating Priority Bus Arbitration Select. When RPBA is high, rotating priority for multiprocessor bus
arbitration is selected. When RPBA is low, fixed priority is selected. This signal is a system configuration
selection that must be set to the same value on every ADSP-2106x. If the value of RPBA is changed during
system operation, it must be changed in the same CLKIN cycle on every ADSP-2106x.
CPA
I/O (O/D)
Core Priority Access. Asserting its CPA pin allows the core processor of an ADSP-2106x bus slave to interrupt
background DMA transfers and gain access to the external bus. CPA is an open drain output that is connected
to all ADSP-2106xs in the system. The CPA pin has an internal 5 k pull-up resistor. If core access priority is
not required in a system, the CPA pin should be left unconnected.
DTx
O
Data Transmit (Serial Ports 0, 1). Each DT pin has a 50 k internal pull-up resistor.
DRx
I
Data Receive (Serial Ports 0, 1). Each DR pin has a 50 k internal pull-up resistor.
TCLKx
I/O
Transmit Clock (Serial Ports 0, 1). Each TCLK pin has a 50 k internal pull-up resistor.
RCLKx
I/O
Receive Clock (Serial Ports 0, 1). Each RCLK pin has a 50 k internal pull-up resistor.
A = Asynchronous, G = Ground, I = Input, O = Output, P = Power Supply, S = Synchronous, (A/D) = Active Drive, (O/D) = Open Drain,
T = Three-State (when SBTS is asserted, or when the ADSP-2106x is a bus slave)
Rev. H |
Page 11 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Table 3. Pin Descriptions (Continued)
Pin
TFSx
RFSx
LxDAT3–0
Type
I/O
I/O
I/O
Function
Transmit Frame Sync (Serial Ports 0, 1).
Receive Frame Sync (Serial Ports 0, 1).
Link Port Data (Link Ports 0–5). Each LxDAT pin has a 50 k internal pull-down resistor that is enabled or
disabled by the LPDRD bit of the LCOM register.
LxCLK
I/O
Link Port Clock (Link Ports 0–5). Each LxCLK pin has a 50 k internal pull-down resistor that is enabled or
disabled by the LPDRD bit of the LCOM register.
LxACK
I/O
Link Port Acknowledge (Link Ports 0–5). Each LxACK pin has a 50 k internal pull-down resistor that is
enabled or disabled by the LPDRD bit of the LCOM register.
EBOOT
I
EPROM Boot Select. When EBOOT is high, the ADSP-2106x is configured for booting from an 8-bit EPROM.
When EBOOT is low, the LBOOT and BMS inputs determine booting mode. See the table in the BMS pin
description below. This signal is a system configuration selection that should be hardwired.
LBOOT
I
Link Boot. When LBOOT is high, the ADSP-2106x is configured for link port booting. When LBOOT is low,
the ADSP-2106x is configured for host processor booting or no booting. See the table in the BMS pin
description below. This signal is a system configuration selection that should be hardwired.
I/OT
Boot Memory Select. Output: Used as chip select for boot EPROM devices (when EBOOT = 1, LBOOT = 0).
BMS
In a multiprocessor system, BMS is output by the bus master. Input: When low, indicates that no booting will
occur and that ADSP-2106x will begin executing instructions from external memory. See table below. This
input is a system configuration selection that should be hardwired. *Three-statable only in EPROM boot
mode (when BMS is an output).
EBOOT
LBOOT
BMS
Booting Mode
1
0
Output
EPROM (Connect BMS to EPROM chip select.)
0
0
1 (Input)
Host Processor
0
1
1 (Input)
Link Port
0
0
0 (Input)
No Booting. Processor executes from external memory.
0
1
0 (Input)
Reserved
1
1
x (Input)
Reserved
CLKIN
I
Clock In. External clock input to the ADSP-2106x. The instruction cycle rate is equal to CLKIN. CLKIN should
not be halted, changed, or operated below the minimum specified frequency.
RESET
I/A
Processor Reset. Resets the ADSP-2106x to a known state and begins program execution at the program
memory location specified by the hardware reset vector address. This input must be asserted (low) at
power-up.
TCK
I
Test Clock (JTAG). Provides an asynchronous clock for JTAG boundary scan.
TMS
I/S
Test Mode Select (JTAG). Used to control the test state machine. TMS has a 20 k internal pull-up resistor.
TDI
I/S
Test Data Input (JTAG). Provides serial data for the boundary scan logic. TDI has a 20 k internal pull-up
resistor.
TDO
O
Test Data Output (JTAG). Serial scan output of the boundary scan path.
TRST
I/A
Test Reset (JTAG). Resets the test state machine. TRST must be asserted (pulsed low) after power-up or held
low for proper operation of the ADSP-2106x. TRST has a 20 k internal pull-up resistor.
EMU
O
Emulation Status. Must be connected to the ADSP-2106x EZ-ICE target board connector only.
ICSA
O
Reserved, leave unconnected.
VDD
P
Power Supply; nominally 5.0 V dc for 5 V devices or 3.3 V dc for 3.3 V devices. (30 pins).
GND
G
Power Supply Return. (30 pins).
NC
Do Not Connect. Reserved pins which must be left open and unconnected.
A = Asynchronous, G = Ground, I = Input, O = Output, P = Power Supply, S = Synchronous, (A/D) = Active Drive, (O/D) = Open Drain,
T = Three-State (when SBTS is asserted, or when the ADSP-2106x is a bus slave)
Rev. H |
Page 12 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
TARGET BOARD CONNECTOR FOR EZ-ICE PROBE
The ADSP-2106x EZ-ICE® Emulator uses the IEEE
1149.1JTAG test access port of the ADSP-2106x to monitor and
control the target board processor during emulation. The
EZ-ICE probe requires the ADSP-2106x’s CLKIN, TMS, TCK,
TRST, TDI, TDO, EMU, and GND signals be made accessible
on the target system via a 14-pin connector (a 2-row 7-pin strip
header) such as that shown in Figure 5. The EZ-ICE probe plugs
directly onto this connector for chip-on-board emulation. You
must add this connector to your target board design if you
intend to use the ADSP-2106x EZ-ICE. The total trace length
between the EZ-ICE connector and the furthest device sharing
the EZ-ICE JTAG pin should be limited to 15 inches maximum
for guaranteed operation. This length restriction must include
EZ-ICE JTAG signals that are routed to one or more
ADSP-2106x devices, or a combination of ADSP-2106x devices
and other JTAG devices on the chain.
The JTAG signals are terminated on the EZ-ICE probe as shown
in Table 4.
Table 4. Core Instruction Rate/CLKIN Ratio Selection
Signal
TMS
TCK
TRST1
TDI
TDO
CLKIN
EMU
1
GND
1
2
3
4
5
TMS
7
8
BTCK
TCK
9
BTRST
10
TRST
9
11
12
BTDI
GND
Connecting CLKIN to Pin 4 of the EZ-ICE header is optional.
The emulator only uses CLKIN when directed to perform operations such as starting, stopping, and single-stepping multiple
ADSP-2106xs in a synchronous manner. If you do not need
these operations to occur synchronously on the multiple processors, simply tie Pin 4 of the EZ-ICE header to ground.
6
BTMS
TDI
13
14
TRST is driven low until the EZ-ICE probe is turned on by the emulator at software
start-up. After software start-up, is driven high.
Figure 6 shows JTAG scan path connections for systems that
contain multiple ADSP-2106x processors.
EMU
GND
KEY (NO PIN)
Termination
Driven Through 22 Resistor (16 mA Driver)
Driven at 10 MHz Through 22 Resistor (16 mA
Driver)
Active Low Driven Through 22 Resistor (16 mA
Driver) (Pulled-Up by On-Chip 20 k Resistor)
Driven by 22 Resistor (16 mA Driver)
One TTL Load, Split Termination (160/220)
One TTL Load, Split Termination (160/220)
Active Low 4.7 k Pull-Up Resistor, One TTL Load
(Open-Drain Output from the DSP)
TDO
TOP VIEW
Figure 5. Target Board Connector for ADSP-2106x EZ-ICE Emulator
(Jumpers in Place)
The 14-pin, 2-row pin strip header is keyed at the Pin 3 location—Pin 3 must be removed from the header. The pins must be
0.025 inch square and at least 0.20 inch in length. Pin spacing
should be 0.1 0.1 inches. Pin strip headers are available from
vendors such as 3M, McKenzie, and Samtec. The BTMS, BTCK,
BTRST, and BTDI signals are provided so that the test access
port can also be used for board-level testing.
When the connector is not being used for emulation, place
jumpers on the Bxxx pins as shown in Figure 5. If you are not
going to use the test access port for board testing, tie BTRST to
GND and tie or pull up BTCK to VDD. The TRST pin must be
asserted (pulsed low) after power-up (through BTRST on the
connector) or held low for proper operation of the ADSP2106x. None of the Bxxx pins (Pins 5, 7, 9, and 11) are connected on the EZ-ICE probe.
Rev. H |
If synchronous multiprocessor operations are needed and
CLKIN is connected, clock skew between the multiple
ADSP-2106x processors and the CLKIN pin on the EZ-ICE
header must be minimal. If the skew is too large, synchronous
operations may be off by one or more cycles between processors. For synchronous multiprocessor operation TCK, TMS,
CLKIN, and EMU should be treated as critical signals in terms
of skew, and should be laid out as short as possible on your
board. If TCK, TMS, and CLKIN are driving a large number of
ADSP-2106xs (more than eight) in your system, then treat them
as a “clock tree” using multiple drivers to minimize skew. (See
Figure 7 and “JTAG Clock Tree” and “Clock Distribution” in
the “High Frequency Design Considerations” section of the
ADSP-2106x User’s Manual, Revision 2.1.)
If synchronous multiprocessor operations are not needed (i.e.,
CLKIN is not connected), just use appropriate parallel termination on TCK and TMS. TDI, TDO, EMU and TRST are not
critical signals in terms of skew.
For complete information on the SHARC EZ-ICE, see the
ADSP-21000 Family JTAG EZ-ICE User's Guide and Reference.
Page 13 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
TR
ST
TRST
EMU
EM U
TRST
TMS
TCK
TDO
TDI
TCK
TDO
TDI
TRST
EMU
TCK
EZ-ICE
JTAG
CONNECTOR
OTHER
JTAG
CONTROLLER
TDO
TDI
TMS
TDI
ADSP-2106x
n
TMS
JTAG
DEVICE
(OPTIONAL)
ADSP-2106x
#1
TCK
TMS
EMU
TRST
TDO
CLKIN
OPTIONAL
Figure 6. JTAG Scan Path Connections for Multiple ADSP-2106x Systems
*
TDI
EMU
*
TDI
TDO
TDI
TDO
TDI
TDO
TDI
TDO
TDI
TDO
TDI
TDO
5k⍀
5k⍀
TCK
TMS
TRST
TDO
CLKIN
EMU
*OPEN-DRAIN DRIVER OR EQUIVALENT, i.e.,
Figure 7. JTAG Clock Tree for Multiple ADSP-2106x Systems
Rev. H |
Page 14 of 64 |
March 2013
SYSTEM
CLKIN
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
ADSP-21060/ADSP-21062 SPECIFICATIONS
Note that component specifications are subject to change
without notice.
OPERATING CONDITIONS (5 V)
A Grade
Parameter
VDD
TCASE
VIH11
VIH22
VIL 1, 2
Description
Supply Voltage
Case Operating Temperature
High Level Input Voltage @ VDD = Max
High Level Input Voltage @ VDD = Max
Low Level Input Voltage @ VDD = Min
Min
4.75
–40
2.0
2.2
–0.5
Max
5.25
+85
VDD + 0.5
VDD + 0.5
+0.8
C Grade
Min
4.75
–40
2.0
2.2
–0.5
Max
5.25
+100
VDD + 0.5
VDD + 0.5
+0.8
K Grade
Min
4.75
–40
2.0
2.2
–0.5
Max
5.25
+85
VDD + 0.5
VDD + 0.5
+0.8
Unit
V
C
V
V
V
1
Applies to input and bidirectional pins: DATA47–0, ADDR31–0, RD, WR, SW, ACK, SBTS, IRQ2–0, FLAG3–0, HGB, CS, DMAR1, DMAR2, BR6–1, ID2–0, RPBA, CPA, TFS0,
TFS1, RFS0, RFS1, LxDAT3–0, LxCLK, LxACK, EBOOT, LBOOT, BMS, TMS, TDI, TCK, HBR, DR0, DR1, TCLK0, TCLK1, RCLK0, RCLK1.
2
Applies to input pins: CLKIN, RESET, TRST.
ELECTRICAL CHARACTERISTICS (5 V)
Parameter
VOH1, 2
VOL1, 2
IIH3, 4
IIL3
IILP4
IOZH5, 6, 7, 8
IOZL5, 9
IOZHP9
IOZLC7
IOZLA10
IOZLAR8
IOZLS6
CIN11, 12
Description
High Level Output Voltage
Low Level Output Voltage
High Level Input Current
Low Level Input Current
Low Level Input Current
Three-State Leakage Current
Three-State Leakage Current
Three-State Leakage Current
Three-State Leakage Current
Three-State Leakage Current
Three-State Leakage Current
Three-State Leakage Current
Input Capacitance
Test Conditions
@ VDD = Min, IOH = –2.0 mA
@ VDD = Min, IOL = 4.0 mA
@ VDD = Max, VIN = VDD Max
@ VDD = Max, VIN = 0 V
@ VDD = Max, VIN = 0 V
@ VDD = Max, VIN = VDD Max
@ VDD = Max, VIN = 0 V
@ VDD = Max, VIN = VDD Max
@ VDD = Max, VIN = 0 V
@ VDD = Max, VIN = 1.5 V
@ VDD = Max, VIN = 0 V
@ VDD = Max, VIN = 0 V
fIN = 1 MHz, TCASE = 25°C, VIN = 2.5 V
1
Min
4.1
Max
0.4
10
10
150
10
10
350
1.5
350
4.2
150
4.7
Unit
V
V
μA
μA
μA
μA
μA
μA
mA
μA
mA
μA
pF
Applies to output and bidirectional pins: DATA47–0, ADDR31-0, MS3–0, RD, WR, PAGE, ADRCLK, SW, ACK, FLAG3–0, TIMEXP, HBG, REDY, DMAG1, DMAG2,
BR6–1, CPA, DT0, DT1, TCLK0, TCLK1, RCLK0, RCLK1, TFS0, TFS1, RFS0, RFS1, LxDAT3–0, LxCLK, LxACK, BMS, TDO, EMU, ICSA.
2
See Figure 31, Output Drive Currents 5 V, for typical drive current capabilities.
3
Applies to input pins: ACK, SBTS, IRQ2–0, HBR, CS, DMAR1, DMAR2, ID2–0, RPBA, EBOOT, LBOOT, CLKIN, RESET, TCK.
4
Applies to input pins with internal pull-ups: DR0, DR1, TRST, TMS, TDI.
5
Applies to three-statable pins: DATA47–0, ADDR31–0, MS3–0, RD, WR, PAGE, ADRCLK, SW, ACK, FLAG3–0, HBG, REDY, DMAG1, DMAG2, BMS, BR6–1, TFSx, RFSx,
TDO, EMU. (Note that ACK is pulled up internally with 2 k during reset in a multiprocessor system, when ID2–0 = 001 and another ADSP-2106x is not requesting bus
mastership.)
6
Applies to three-statable pins with internal pull-ups: DT0, DT1, TCLK0, TCLK1, RCLK0, RCLK1.
7
Applies to CPA pin.
8
Applies to ACK pin when pulled up. (Note that ACK is pulled up internally with 2 k during reset in a multiprocessor system, when ID2–0 = 001 and another ADSP-2106xL
is not requesting bus mastership).
9
Applies to three-statable pins with internal pull-downs: LxDAT3–0, LxCLK, LxACK.
10
Applies to ACK pin when keeper latch enabled.
11
Applies to all signal pins.
12
Guaranteed but not tested.
Rev. H |
Page 15 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
INTERNAL POWER DISSIPATION (5 V)
These specifications apply to the internal power portion of VDD
only. For a complete discussion of the code used to measure
power dissipation, see the technical note “SHARC Power Dissipation Measurements.”
Specifications are based on the operating scenarios.
Operation
Instruction Type
Instruction Fetch
Core memory Access
Internal Memory DMA
Peak Activity (IDDINPEAK)
Multifunction
Cache
2 Per Cycle (DM and PM)
1 Per Cycle
High Activity (IDDINHIGH)
Multifunction
Internal Memory
1 Per Cycle (DM)
1 Per 2 Cycles
Low Activity (IDDINLOW)
Single Function
Internal Memory
None
1 Per 2 Cycles
To estimate power consumption for a specific application, use
the following equation where% is the amount of time your program spends in that state:
%PEAK IDDINPEAK +%HIGH IDDINHIGH +%LOW IDDINLOW +
%IDLE IDDIDLE = Power Consumption
Parameter
IDDINPEAK Supply Current (Internal)1
IDDINHIGH Supply Current (Internal)2
IDDINLOW Supply Current (Internal)2
IDDIDLE Supply Current (Idle)3
Test Conditions
tCK = 30 ns, VDD = Max
tCK = 25 ns, VDD = Max
tCK = 30 ns, VDD = Max
tCK = 25 ns, VDD = Max
tCK = 30 ns, VDD = Max
tCK = 25 ns, VDD = Max
VDD = Max
Max
745
850
575
670
340
390
200
1
Unit
mA
mA
mA
mA
mA
mA
mA
The test program used to measure IDDINPEAK represents worst case processor operation and is not sustainable under normal application conditions. Actual internal power
measurements made using typical applications are less than specified.
2
IDDINHIGH is a composite average based on a range of high activity code. IDDINLOW is a composite average based on a range of low activity code.
3
Idle denotes ADSP-2106x state during execution of IDLE instruction.
Rev. H |
Page 16 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
EXTERNAL POWER DISSIPATION (5 V)
Total power dissipation has two components, one due to internal circuitry and one due to the switching of external output
drivers. Internal power dissipation is dependent on the instruction execution sequence and the data operands involved.
Internal power dissipation is calculated in the following way:
drive high and low at a maximum rate of 1/(2tCK). The write
strobe can switch every cycle at a frequency of 1/tCK. Select pins
switch at 1/(2tCK), but selects can switch on each cycle.
Example: Estimate PEXT with the following assumptions:
• A system with one bank of external data memory RAM
(32-bit)
PINT = IDDIN VDD
• Four 128K 8 RAM chips are used, each with a load of
10 pF
The external component of total power dissipation is caused by
the switching of output pins. Its magnitude depends on:
• External data memory writes occur every other cycle, a rate
of 1/(4tCK), with 50% of the pins switching
• the number of output pins that switch during each cycle
(O)
• The instruction cycle rate is 40 MHz (tCK = 25 ns)
• the maximum frequency at which they can switch (f)
The PEXT equation is calculated for each class of pins that can
drive:
• their load capacitance (C)
A typical power consumption can now be calculated for these
conditions by adding a typical internal power dissipation:
• their voltage swing (VDD)
and is calculated by:
PTOTAL = PEXT + (IDDIN2 5.0 V)
PEXT = O C VDD2 f
Note that the conditions causing a worst-case PEXT are different
from those causing a worst-case PINT. Maximum PINT cannot
occur while 100% of the output pins are switching from all ones
to all zeros. Note also that it is not common for an application to
have 100% or even 50% of the outputs switching
simultaneously.
The load capacitance should include the processor’s package
capacitance (CIN). The switching frequency includes driving
the load high and then back low. Address and data pins can
Table 5. External Power Calculations (5 V Devices)
Pin Type
Address
MS0
WR
Data
ADDRCLK
No. of Pins
15
1
1
32
1
% Switching
50
0
–
50
–
Rev. H |
C
44.7 pF
44.7 pF
44.7 pF
14.7 pF
4.7 pF
Page 17 of 64 |
f
10 MHz
10 MHz
20 MHz
10 MHz
20 MHz
March 2013
VDD2
25 V
25 V
25 V
25 V
25 V
= PEXT
= 0.084 W
= 0.000 W
= 0.022 W
= 0.059 W
= 0.002 W
PEXT = 0.167 W
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
ADSP-21060L/ADSP-21062L SPECIFICATIONS
Note that component specifications are subject to change
without notice.
OPERATING CONDITIONS (3.3 V)
A Grade
Parameter
VDD
TCASE
VIH11
VIH22
VIL 1, 2
Description
Supply Voltage
Case Operating Temperature
High Level Input Voltage @ VDD = Max
High Level Input Voltage @ VDD = Max
Low Level Input Voltage @ VDD = Min
Min
3.15
–40
2.0
2.2
–0.5
Max
3.45
+85
VDD + 0.5
VDD + 0.5
+0.8
C Grade
Min
3.15
–40
2.0
2.2
–0.5
Max
3.45
+100
VDD + 0.5
VDD + 0.5
+0.8
K Grade
Min
3.15
–40
2.0
2.2
–0.5
Max
3.45
+85
VDD + 0.5
VDD + 0.5
+0.8
Unit
V
C
V
V
V
1
Applies to input and bidirectional pins: DATA47–0, ADDR31–0, RD, WR, SW, ACK, SBTS, IRQ2–0, FLAG3–0, HGB, CS, DMAR1, DMAR2, BR6–1, ID2–0, RPBA, CPA,
TFS0, TFS1, RFS0, RFS1, LxDAT3–0, LxCLK, LxACK, EBOOT, LBOOT, BMS, TMS, TDI, TCK, HBR, DR0, DR1, TCLK0, TCLK1, RCLK0, RCLK1.
2
Applies to input pins: CLKIN, RESET, TRST.
ELECTRICAL CHARACTERISTICS (3.3 V)
Parameter
VOH1, 2
VOL1, 2
IIH3, 4
IIL3
IILP4
IOZH5, 6, 7, 8
IOZL5, 9
IOZHP9
IOZLC7
IOZLA10
IOZLAR8
IOZLS6
CIN11, 12
Description
High Level Output Voltage
Low Level Output Voltage
High Level Input Current
Low Level Input Current
Low Level Input Current
Three-State Leakage Current
Three-State Leakage Current
Three-State Leakage Current
Three-State Leakage Current
Three-State Leakage Current
Three-State Leakage Current
Three-State Leakage Current
Input Capacitance
Test Conditions
@ VDD = Min, IOH = –2.0 mA
@ VDD = Min, IOL = 4.0 mA
@ VDD = Max, VIN = VDD Max
@ VDD = Max, VIN = 0 V
@ VDD = Max, VIN = 0 V
@ VDD = Max, VIN = VDD Max
@ VDD = Max, VIN = 0 V
@ VDD = Max, VIN = VDD Max
@ VDD = Max, VIN = 0 V
@ VDD = Max, VIN = 1.5 V
@ VDD = Max, VIN = 0 V
@ VDD = Max, VIN = 0 V
fIN = 1 MHz, TCASE = 25°C, VIN = 2.5 V
1
Min
2.4
Max
0.4
10
10
150
10
10
350
1.5
350
4.2
150
4.7
Unit
V
V
μA
μA
μA
μA
μA
μA
mA
μA
mA
μA
pF
Applies to output and bidirectional pins: DATA47–0, ADDR31–0, MS3–0, RD, WR, PAGE, ADRCLK, SW, ACK, FLAG3–0, TIMEXP, HBG, REDY, DMAG1, DMAG2,
BR6–1, CPA, DT0, DT1, TCLK0, TCLK1, RCLK0, RCLK1, TFS0, TFS1, RFS0, RFS1, LxDAT3–0, LxCLK, LxACK, BMS, TDO, EMU, ICSA.
2
See Figure 35, Output Drive Currents 3.3 V, for typical drive current capabilities.
3
Applies to input pins: ACK, SBTS, IRQ2–0, HBR, CS, DMAR1, DMAR2, ID2–0, RPBA, EBOOT, LBOOT, CLKIN, RESET, TCK.
4
Applies to input pins with internal pull-ups: DR0, DR1, TRST, TMS, TDI.
5
Applies to three-statable pins: DATA47–0, ADDR31–0, MS3–0, RD, WR, PAGE, ADRCLK, SW, ACK, FLAG3–0, HBG, REDY, DMAG1, DMAG2, BMS, BR6–1, TFSx, RFSx,
TDO, EMU. (Note that ACK is pulled up internally with 2 k during reset in a multiprocessor system, when ID2–0 = 001 and another ADSP-2106x is not requesting bus
mastership.)
6
Applies to three-statable pins with internal pull-ups: DT0, DT1, TCLK0, TCLK1, RCLK0, RCLK1.
7
Applies to CPA pin.
8
Applies to ACK pin when pulled up. (Note that ACK is pulled up internally with 2 k during reset in a multiprocessor system, when ID2–0 = 001 and another ADSP-2106xL
is not requesting bus mastership).
9
Applies to three-statable pins with internal pull-downs: LxDAT3–0, LxCLK, LxACK.
10
Applies to ACK pin when keeper latch enabled.
11
Applies to all signal pins.
12
Guaranteed but not tested.
Rev. H |
Page 18 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
INTERNAL POWER DISSIPATION (3.3 V)
These specifications apply to the internal power portion of VDD
only. For a complete discussion of the code used to measure
power dissipation, see the technical note “SHARC Power Dissipation Measurements.”
Specifications are based on the operating scenarios.
Operation
Instruction Type
Instruction Fetch
Core memory Access
Internal Memory DMA
Peak Activity (IDDINPEAK)
Multifunction
Cache
2 Per Cycle (DM and PM)
1 Per Cycle
High Activity (IDDINHIGH)
Multifunction
Internal Memory
1 Per Cycle (DM)
1 Per 2 Cycles
Low Activity (IDDINLOW)
Single Function
Internal Memory
None
1 Per 2 Cycles
To estimate power consumption for a specific application, use
the following equation where % is the amount of time your program spends in that state:
%PEAK IDDINPEAK + %HIGH IDDINHIGH + %LOW IDDINLOW +
%IDLE IDDIDLE = Power Consumption
Parameter
IDDINPEAK Supply Current (Internal)1
IDDINHIGH Supply Current (Internal)2
IDDINLOW Supply Current (Internal)2
IDDIDLE Supply Current (Idle)3
Test Conditions
tCK = 30 ns, VDD = Max
tCK = 25 ns, VDD = Max
tCK = 30 ns, VDD = Max
tCK = 25 ns, VDD = Max
tCK = 30 ns, VDD = Max
tCK = 25 ns, VDD = Max
VDD = Max
Max
540
600
425
475
250
275
180
1
Unit
mA
mA
mA
mA
mA
mA
mA
The test program used to measure IDDINPEAK represents worst case processor operation and is not sustainable under normal application conditions. Actual internal power
measurements made using typical applications are less than specified.
2
IDDINHIGH is a composite average based on a range of high activity code. IDDINLOW is a composite average based on a range of low activity code.
3
Idle denotes ADSP-2106xL state during execution of IDLE instruction.
Rev. H |
Page 19 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
EXTERNAL POWER DISSIPATION (3.3 V)
drive high and low at a maximum rate of 1/(2tCK). The write
strobe can switch every cycle at a frequency of 1/tCK. Select pins
switch at 1/(2tCK), but selects can switch on each cycle.
Total power dissipation has two components, one due to internal circuitry and one due to the switching of external output
drivers. Internal power dissipation is dependent on the instruction execution sequence and the data operands involved.
Internal power dissipation is calculated in the following way:
Example: Estimate PEXT with the following assumptions:
• A system with one bank of external data memory RAM
(32-bit)
PINT = IDDIN VDD
• Four 128K 8 RAM chips are used, each with a load of
10 pF
The external component of total power dissipation is caused by
the switching of output pins. Its magnitude depends on:
• External data memory writes occur every other cycle, a rate
of 1/(4tCK), with 50% of the pins switching
• the number of output pins that switch during each cycle
(O)
• The instruction cycle rate is 40 MHz (tCK = 25 ns)
• the maximum frequency at which they can switch (f)
The PEXT equation is calculated for each class of pins that can
drive:
• their load capacitance (C)
A typical power consumption can now be calculated for these
conditions by adding a typical internal power dissipation:
• their voltage swing (VDD)
and is calculated by:
PTOTAL = PEXT + (IDDIN2 3.3 V)
PEXT = O C VDD2 f
Note that the conditions causing a worst-case PEXT are different
from those causing a worst-case PINT. Maximum PINT cannot
occur while 100% of the output pins are switching from all ones
to all zeros. Note also that it is not common for an application to
have 100% or even 50% of the outputs switching
simultaneously.
The load capacitance should include the processor’s package
capacitance (CIN). The switching frequency includes driving
the load high and then back low. Address and data pins can
Table 6. External Power Calculations (3.3 V Devices)
Pin Type
Address
MS0
WR
Data
ADDRCLK
No. of Pins
15
1
1
32
1
C
44.7 pF
44.7 pF
44.7 pF
14.7 pF
4.7 pF
% Switching
50
0
–
50
–
f
10 MHz
10 MHz
20 MHz
10 MHz
20 MHz
VDD2
10.9 V
10.9 V
10.9 V
10.9 V
10.9 V
= PEXT
= 0.037 W
= 0.000 W
= 0.010 W
= 0.026 W
= 0.001 W
PEXT = 0.074 W
ABSOLUTE MAXIMUM RATINGS
Stresses greater than those listed Table 7 may cause permanent
damage to the device. These are stress ratings only; functional
operation of the device at these or any other conditions greater
than those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
Table 7. Absolute Maximum Ratings
ADSP-21060/ADSP-21060C
ADSP-21062
5V
–0.3 V to +7.0 V
–0.5 V to VDD + 0.5 V
–0.5 V to VDD + 0.5 V
200 pF
–65C to +150C
280C
130C
Parameter
Supply Voltage (VDD)
Input Voltage
Output Voltage Swing
Load Capacitance
Storage Temperature Range
Lead Temperature (5 seconds)
Junction Temperature Under Bias
Rev. H |
Page 20 of 64 |
March 2013
ADSP-21060L/ADSP-21060LC
ADSP-21062L
3.3 V
–0.3 V to +4.6 V
–0.5 V to VDD +0.5 V
–0.5 V to VDD + 0.5 V
200 pF
–65C to +150C
280C
130C
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
ESD CAUTION
TIMING SPECIFICATIONS
ESD (electrostatic discharge) sensitive device.
Charged devices and circuit boards can discharge
without detection. Although this product features
patented or proprietary protection circuitry, damage
may occur on devices subjected to high energy ESD.
Therefore, proper ESD precautions should be taken to
avoid performance degradation or loss of functionality.
The ADSP-2106x processors are available at maximum processor speeds of 33 MHz (–133), and 40 MHz (–160). The timing
specifications are based on a CLKIN frequency of 40 MHz
tCK = 25 ns). The DT derating factor enables the calculation for
timing specifications within the min to max range of the tCK
specification (see Table 9). DT is the difference between the
derated CLKIN period and a CLKIN period of 25 ns:
DT = tCK – 25 ns
PACKAGE MARKING INFORMATION
Figure 8 and Table 8 provide information on detail contained
within the package marking for the ADSP-2106x processors
(actual marking format may vary). For a complete listing of
product availability, see Ordering Guide on Page 62.
Use the exact timing information given. Do not attempt to
derive parameters from the addition or subtraction of others.
While addition or subtraction would yield meaningful results
for an individual device, the values given in this data sheet
reflect statistical variations and worst cases. Consequently, you
cannot meaningfully add parameters to derive longer times.
For voltage reference levels, see Figure 28 on Page 48 under Test
Conditions.
Timing Requirements apply to signals that are controlled by circuitry external to the processor, such as the data input for a read
operation. Timing requirements guarantee that the processor
operates correctly with other devices. (O/D) = Open Drain,
(A/D) = Active Drive.
a
ADSP-2106x
tppZccc
Switching Characteristics specify how the processor changes its
signals. You have no control over this timing—circuitry external
to the processor must be designed for compatibility with these
signal characteristics. Switching characteristics tell you what the
processor will do in a given circumstance. You can also use
switching characteristics to ensure that any timing requirement
of a device connected to the processor (such as memory) is
satisfied.
vvvvvv.x n.n
yyww country_of_origin
S
Figure 8. Typical Package Brand
Table 8. Package Brand Information
Brand Key
t
pp
Z
ccc
vvvvvv.x
n.n
yyww
Field Description
Temperature Range
Package Type
Lead (Pb) Free Option
See Ordering Guide
Assembly Lot Code
Silicon Revision
Date Code
Rev. H |
Page 21 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Clock Input
Table 9. Clock Input
Parameter
Timing Requirements
tCK
CLKIN Period
tCKL
CLKIN Width Low
tCKH CLKIN Width High
tCKRF CLKIN Rise/Fall (0.4 V to 2.0 V)
1
ADSP-21060
ADSP-21062
40 MHz, 5 V
Min
Max
ADSP-21060
ADSP-21062
33 MHz, 5 V
Min
Max
ADSP-21060L
ADSP-21062L
40 MHz, 3.3 V
Min
Max
ADSP-21060L
ADSP-21062L
33 MHz, 3.3 V
Min
Max
25
7
5
30
7
5
25
8.75
5
30
8.751
5
100
100
3
100
3
3
Unit
100
ns
ns
ns
ns
3
For the ADSP-21060LC, this specification is 9.5 ns min.
tCK
CLKIN
tCKH
tCKL
Figure 9. Clock Input
Reset
Table 10. Reset
Parameter
Timing Requirements
tWRST
RESET Pulse Width Low1
tSRST
RESET Setup Before CLKIN High2
Min
5 V and 3.3 V
Max
4tCK
14 + DT/2
tCK
1
Unit
ns
ns
Applies after the power-up sequence is complete. At power-up, the processor’s internal phase-locked loop requires no more than 100 μs while RESET is low, assuming stable
VDD and CLKIN (not including start-up time of external clock oscillator).
2
Only required if multiple ADSP-2106xs must come out of reset synchronous to CLKIN with program counters (PC) equal. Not required for multiple ADSP-2106xs communicating over the shared bus (through the external port), because the bus arbitration logic automatically synchronizes itself after reset.
CLKIN
tSRST
tWRST
RESET
Figure 10. Reset
Rev. H |
Page 22 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Interrupts
Table 11. Interrupts
Parameter
Timing Requirements
tSIR
IRQ2–0 Setup Before CLKIN High1
tHIR
IRQ2–0 Hold Before CLKIN High1
tIPW
IRQ2–0 Pulse Width2
1
2
5 V and 3.3 V
Max
Min
18 + 3DT/4
12 + 3DT/4
2+tCK
Unit
ns
ns
ns
Only required for IRQx recognition in the following cycle.
Applies only if tSIR and tHIR requirements are not met.
CLKIN
tSIR
tHIR
IRQ2–0
tIPW
Figure 11. Interrupts
Timer
Table 12. Timer
Parameter
Switching Characteristic
tDTEX
CLKIN High to TIMEXP
Min
5 V and 3.3 V
Max
Unit
15
ns
CLKIN
tDTEX
tDTEX
TIMEXP
Figure 12. Timer
Rev. H |
Page 23 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Flags
Table 13. Flags
Parameter
Timing Requirements
tSFI
FLAG3–0 IN Setup Before CLKIN High1
tHFI
FLAG3–0 IN Hold After CLKIN High1
tDWRFI
FLAG3–0 IN Delay After RD/WR Low1
tHFIWR
FLAG3–0 IN Hold After RD/WR Deasserted1
Switching Characteristics
FLAG3–0 OUT Delay After CLKIN High
tDFO
tHFO
FLAG3–0 OUT Hold After CLKIN High
tDFOE
CLKIN High to FLAG3–0 OUT Enable
tDFOD
CLKIN High to FLAG3–0 OUT Disable
1
Min
5 V and 3.3 V
Max
8 + 5DT/16
0 – 5DT/16
5 + 7DT/16
0
16
4
3
14
Flag inputs meeting these setup and hold times for instruction cycle N will affect conditional instructions in instruction cycle N+2.
CLKIN
tDFOE
tDFO
tDFO
tHFO
FLAG3–0 OUT
FLAG OUTPUT
CLKIN
tSFI
tHFI
FLAG3–0 IN
tDWRFI
tHFIWR
RD/WR
FLAG INPUT
Figure 13. Flags
Rev. H |
Page 24 of 64 |
March 2013
tDFOD
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
bus master accessing external memory space in asynchronous
access mode. Note that timing for ACK, DATA, RD, WR, and
DMAGx strobe timing parameters only applies to asynchronous
access mode.
Memory Read—Bus Master
Use these specifications for asynchronous interfacing to memories (and memory-mapped peripherals) without reference to
CLKIN. These specifications apply when the ADSP-2106x is the
Table 14. Memory Read—Bus Master
5 V and 3.3 V
Parameter
Min
Max
Timing Requirements
tDAD
Address Selects Delay to Data Valid1, 2
18 + DT+W
tDRLD
RD Low to Data Valid1
12 + 5DT/8 + W
3
tHDA
Data Hold from Address, Selects
0.5
tHDRH
Data Hold from RD High3
2.0
tDAAK
ACK Delay from Address, Selects2, 4
14 + 7DT/8 + W
4
ACK Delay from RD Low
8 + DT/2 + W
tDSAK
Switching Characteristics
tDRHA
Address Selects Hold After RD High
0+H
2
tDARL
Address Selects to RD Low
2 + 3DT/8
tRW
RD Pulse Width
12.5 + 5DT/8 + W
tRWR
RD High to WR, RD, DMAGx Low
8 + 3DT/8 + HI
Address, Selects Setup Before ADRCLK High2
0 + DT/4
tSADADC
W = (number of wait states specified in WAIT register) × tCK.
HI = tCK (if an address hold cycle or bus idle cycle occurs, as specified in WAIT register; otherwise HI = 0).
H = tCK (if an address hold cycle occurs as specified in WAIT register; otherwise H = 0).
1
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Data delay/setup: user must meet tDAD or tDRLD or synchronous spec tSSDATI.
The falling edge of MSx, SW, BMS is referenced.
3
Data hold: user must meet tHDA or tHDRH or synchronous spec tHSDATI. See Example System Hold Time Calculation on Page 48 for the calculation of hold times given capacitive
and dc loads.
4
ACK is not sampled on external memory accesses that use the internal wait state mode. For the first CLKIN cycle of a new external memory access, ACK must be valid by
tDAAK or tDSAK or synchronous specification tSACKC for wait state modes external, either, or both (both, if the internal wait state is zero). For the second and subsequent cycles
of a wait stated external memory access, synchronous specifications tSACKC and tHACK must be met for wait state modes external, either, or both (both, after internal wait
states have completed).
2
ADDRESS
MSx, SW
BMS
tDARL
tDRHA
tRW
RD
tHDA
tDRLD
tDAD
tHDRH
DATA
tDSAK
tRWR
tDAAK
ACK
WR, DMAG
tSADADC
ADRCLK
(OUT)
Figure 14. Memory Read—Bus Master
Rev. H |
Page 25 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Memory Write—Bus Master
Use these specifications for asynchronous interfacing to memories (and memory-mapped peripherals) without reference to
CLKIN. These specifications apply when the ADSP-2106x is the
bus master accessing external memory space in asynchronous
access mode. Note that timing for ACK, DATA, RD, WR, and
DMAGx strobe timing parameters only applies to asynchronous
access mode.
Table 15. Memory Write—Bus Master
5 V and 3.3 V
Parameter
Min
Max
Timing Requirements
tDAAK
ACK Delay from Address, Selects1, 2
14 + 7DT/8 + W
tDSAK
ACK Delay from WR Low1
8 + DT/2 + W
Switching Characteristics
tDAWH
Address Selects to WR Deasserted2
17 + 15DT/16 + W
tDAWL
Address Selects to WR Low2
3 + 3DT/8
WR Pulse Width
12 + 9DT/16 + W
tWW
tDDWH
Data Setup Before WR High
7 + DT/2 + W
tDWHA
Address Hold After WR Deasserted
0.5 + DT/16 + H
tDATRWH
Data Disable After WR Deasserted3
1 + DT/16 +H
6 + DT/16+H
tWWR
WR High to WR, RD, DMAGx Low
8 + 7DT/16 + H
tDDWR
Data Disable Before WR or RD Low
5 + 3DT/8 + I
WR Low to Data Enabled
–1 + DT/16
tWDE
tSADADC
Address, Selects Setup Before ADRCLK High2
0 + DT/4
W = (number of wait states specified in WAIT register) × tCK.
H = tCK (if an address hold cycle occurs, as specified in WAIT register; otherwise H = 0).
HI = tCK (if an address hold cycle or bus idle cycle occurs, as specified in WAIT register; otherwise HI = 0).
I = tCK (if a bus idle cycle occurs, as specified in WAIT register; otherwise I = 0).
1
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ACK is not sampled on external memory accesses that use the internal wait state mode. For the first CLKIN cycle of a new external memory access, ACK must be valid by
tDAAK or tDSAK or synchronous specification tSACKC for wait state modes external, either, or both (both, if the internal wait state is zero). For the second and subsequent cycles
of a wait stated external memory access, synchronous specifications tSACKC and tHACK must be met for wait state modes external, either, or both (both, after internal wait
states have completed).
2
The falling edge of MSx, SW, BMS is referenced.
3
See Example System Hold Time Calculation on Page 48 for calculation of hold times given capacitive and dc loads.
Rev. H |
Page 26 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
ADDRESS
MSx, SW
BMS
tDAWH
tDAWL
tDWHA
tWW
WR
tWWR
tDDWH
tWDE
tDATRWH
DATA
tDSAK
tDAAK
ACK
RD, DMAG
tSADADC
ADRCLK
(OUT)
Figure 15. Memory Write—Bus Master
Rev. H |
Page 27 of 64 |
March 2013
tDDWR
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Synchronous Read/Write—Bus Master
Use these specifications for interfacing to external memory systems that require CLKIN—relative timing or for accessing a
slave ADSP-2106x (in multiprocessor memory space). These
synchronous switching characteristics are also valid during
asynchronous memory reads and writes except where noted (see
Memory Read—Bus Master on Page 25 and Memory Write—
Bus Master on Page 26). When accessing a slave ADSP-2106x,
these switching characteristics must meet the slave’s timing
requirements for synchronous read/writes (see Synchronous
Read/Write—Bus Slave on Page 30). The slave ADSP-2106x
must also meet these (bus master) timing requirements for data
and acknowledge setup and hold times.
Table 16. Synchronous Read/Write—Bus Master
Parameter
Timing Requirements
tSSDATI
tHSDATI
tDAAK
tSACKC
tHACK
Switching Characteristics
tDADRO
tHADRO
tDPGC
tDRDO
tDWRO
tDRWL
tSDDATO
tDATTR
tDADCCK
tADRCK
tADRCKH
tADRCKL
Min
Data Setup Before CLKIN
Data Hold After CLKIN
ACK Delay After Address, Selects1, 2
ACK Setup Before CLKIN2
ACK Hold After CLKIN
5 V and 3.3 V
Max
3 + DT/8
3.5 – DT/8
14 + 7DT/8 + W
6.5+DT/4
–1 – DT/4
Address, MSx, BMS, SW Delay After CLKIN1
Address, MSx, BMS, SW Hold After CLKIN
PAGE Delay After CLKIN
RD High Delay After CLKIN
WR High Delay After CLKIN
RD/WR Low Delay After CLKIN
Data Delay After CLKIN
Data Disable After CLKIN3
ADRCLK Delay After CLKIN
ADRCLK Period
ADRCLK Width High
ADRCLK Width Low
7 – DT/8
–1 – DT/8
9 + DT/8
–2 – DT/8
–3 – 3DT/16
8 + DT/4
0 – DT/8
4 + DT/8
tCK
(tCK /2 – 2)
(tCK /2 – 2)
1
16 + DT/8
4 – DT/8
4 – 3DT/16
12.5 + DT/4
19 + 5DT/16
7 – DT/8
10 + DT/8
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
The falling edge of MSx, SW, BMS is referenced.
ACK delay/setup: user must meet tDAAK or tDSAK or synchronous specification tSAKC for deassertion of ACK (low), all three specifications must be met for assertion of ACK
(high).
3
See Example System Hold Time Calculation on Page 48 for calculation of hold times given capacitive and dc loads.
2
Rev. H |
Page 28 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
CLKIN
tADRCK
tDADCCK
tADRCKH
tDADRO
tDAAK
tADRCKL
ADDRCLK
tHADRO
ADDRESS,
BMS, SW, MSx
tDPGC
PAGE
tHACK
tSACKC
ACK
(IN)
READ CYCLE
tDRWL
tDRDO
RD
tSSDATI
tHSDATI
DATA (IN)
WRITE CYCLE
tDWRO
tDRWL
WR
tDATTR
tSDDATO
DATA
(OUT)
Figure 16. Synchronous Read/Write—Bus Master
Rev. H |
Page 29 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Synchronous Read/Write—Bus Slave
Use these specifications for bus master accesses of a slave’s IOP
registers or internal memory (in multiprocessor memory space).
The bus master must meet the bus slave timing requirements.
Table 17. Synchronous Read/Write—Bus Slave
Parameter
Timing Requirements
tSADRI
Address, SW Setup Before CLKIN
tHADRI
Address, SW Hold After CLKIN
tSRWLI
RD/WR Low Setup Before CLKIN1
tHRWLI
RD/WR Low Hold After CLKIN2
tRWHPI
RD/WR Pulse High
Data Setup Before WR High
tSDATWH
tHDATWH
Data Hold After WR High
Switching Characteristics
tSDDATO
Data Delay After CLKIN3
tDATTR
Data Disable After CLKIN4
tDACKAD
ACK Delay After Address, SW5
ACK Disable After CLKIN5
tACKTR
5 V and 3.3 V
Max
Min
Unit
15 + DT/2
8 + 7DT/16
ns
ns
ns
ns
ns
ns
ns
18 + 5DT/16
7 – DT/8
9
6 – DT/8
ns
ns
ns
ns
5 + DT/2
9.5 + 5DT/16
–4 – 5DT/16
3
5
1
0 – DT/8
–1 – DT/8
1
tSRWLI (min) = 9.5 + 5DT/16 when Multiprocessor Memory Space Wait State (MMSWS bit in WAIT register) is disabled; when MMSWS is enabled, tSRWLI (min)= 4 + DT/8.
For ADSP-21060C specification is –3.5 – 5DT/16 ns min, 8 + 7DT/16 ns max; for ADSP-21060LC specification is –3.75 – 5DT/16 ns min, 8 + 7DT/16 ns max.
3
For ADSP-21062/ADSP-21062L/ADSP-21060C specification is 19 + 5DT/16 ns max; for ADSP-21060LC specification is 19.25 + 5DT/16 ns max.
4
See Example System Hold Time Calculation on Page 48 for calculation of hold times given capacitive and dc loads.
5
tDACKAD is true only if the address and SW inputs have setup times (before CLKIN) greater than 10 + DT/8 and less than 19 + 3DT/4. If the address and inputs have setup times
greater than 19 + 3DT/4, then ACK is valid 14 + DT/4 (max) after CLKIN. A slave that sees an address with an M field match will respond with ACK regardless of the state
of MMSWS or strobes. A slave will three-state ACK every cycle with tACKTR.
2
CLKIN
tS A DR I
tH A DR I
ADDRESS
t AC K TR
t D AC K AD
ACK
t SR WLI
READ ACCESS
tH RW L I
t R W HP I
RD
t D AT T R
tSD D AT O
DATA
(OU T)
WRITE ACCESS
tH RW L I
t SR W LI
t R WH PI
WR
DATA
(IN)
t S D AT WH
Figure 17. Synchronous Read/Write—Bus Slave
Rev. H |
Page 30 of 64 |
March 2013
t H D ATW H
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Multiprocessor Bus Request and Host Bus Request
Use these specifications for passing of bus mastership between
multiprocessing ADSP-2106xs (BRx) or a host processor, both
synchronous and asynchronous (HBR, HBG).
Table 18. Multiprocessor Bus Request and Host Bus Request
Parameter
Timing Requirements
tHBGRCSV
HBG Low to RD/WR/CS Valid1
tSHBRI
HBR Setup Before CLKIN2
tHHBRI
HBR Hold After CLKIN2
tSHBGI
HBG Setup Before CLKIN
tHHBGI
HBG Hold After CLKIN High
BRx, CPA Setup Before CLKIN3
tSBRI
tHBRI
BRx, CPA Hold After CLKIN High
tSRPBAI
RPBA Setup Before CLKIN
tHRPBAI
RPBA Hold After CLKIN
Switching Characteristics
tDHBGO
HBG Delay After CLKIN
HBG Hold After CLKIN
tHHBGO
tDBRO
BRx Delay After CLKIN
tHBRO
BRx Hold After CLKIN
tDCPAO
CPA Low Delay After CLKIN4
tTRCPA
CPA Disable After CLKIN
tDRDYCS
REDY (O/D) or (A/D) Low from CS and HBR Low5, 6
tTRDYHG
REDY (O/D) Disable or REDY (A/D) High from HBG6, 7
REDY (A/D) Disable from CS or HBR High6
tARDYTR
Min
5 V and 3.3 V
Max
20 + 5DT/4
20 + 3DT/4
14 + 3DT/4
13 + DT/2
6 + DT/2
13 + DT/2
6 + DT/2
21 + 3DT/4
12 + 3DT/4
7 – DT/8
–2 – DT/8
7 – DT/8
–2 – DT/8
–2 – DT/8
8 – DT/8
4.5 – DT/8
8.5
44 + 23DT/16
10
1
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
For first asynchronous access after HBR and CS asserted, ADDR31-0 must be a non-MMS value 1/2 tCK before RD or WR goes low or by tHBGRCSV after HBG goes low. This is
easily accomplished by driving an upper address signal high when HBG is asserted. See the “Host Processor Control of the ADSP-2106x” section in the ADSP-2106x SHARC
User’s Manual, Revision 2.1.
2
Only required for recognition in the current cycle.
3
CPA assertion must meet the setup to CLKIN; deassertion does not need to meet the setup to CLKIN.
4
For ADSP-21060LC, specification is 8.5 – DT/8 ns max.
5
For ADSP-21060L, specification is 9.5 ns max, For ADSP-21060LC, specification is 11.0 ns max, For ADSP-21062L, specification is 8.75 ns max.
6
(O/D) = open drain, (A/D) = active drive.
7
For ADSP-21060C/ADSP-21060LC, specification is 40 + 23DT/16 ns min.
Rev. H |
Page 31 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
CLKIN
tSH B R I
tH H B R I
HBR
tD HB GO
tH H B GO
HBG (OUT)
tD B R O
tH B R O
BRx (OUT)
tTRC P A
tD C PA O
CPA (OUT, O/D)
tSH B GI
tH H B GI
HBG (I N)
tSB R I
tH B R I
BRx, CPA (IN, O/ D)
tS R PB A I
tH R PB A I
RPBA
HBR
CS
tTR D YH G
tD RD Y C S
REDY
(O/D)
tA R DY TR
REDY
(A/D)
tH B GR C SV
HBG (OUT)
RD
WR
CS
O/D = O PEN DRAIN, A/D = ACTIVE DRIVE
Figure 18. Multiprocessor Bus Request and Host Bus Request
Rev. H |
Page 32 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Asynchronous Read/Write—Host to ADSP-2106x
Use these specifications for asynchronous host processor
accesses of an ADSP-2106x, after the host has asserted CS and
HBR (low). After HBG is returned by the ADSP-2106x, the host
can drive the RD and WR pins to access the ADSP-2106x’s
internal memory or IOP registers. HBR and HBG are assumed
low for this timing. Not required if and address are valid tHBGRCSV
after goes low. For first access after asserted, ADDR31–0 must
be a non-MMS value 1/2 tCLK before or goes low or by tHBGRCSV
after goes low. This is easily accomplished by driving an upper
address signal high when is asserted. See the “Host Processor
Control of the ADSP-2106x” section in the ADSP-2106x
SHARC User’s Manual, Revision 2.1.
Table 19. Read Cycle
Parameter
Timing Requirements
tSADRDL
Address Setup/CS Low Before RD Low1
tHADRDH
Address Hold/CS Hold Low After RD
tWRWH
RD/WR High Width
tDRDHRDY
RD High Delay After REDY (O/D) Disable
tDRDHRDY
RD High Delay After REDY (A/D) Disable
Switching Characteristics
tSDATRDY
Data Valid Before REDY Disable from Low
tDRDYRDL
REDY (O/D) or (A/D) Low Delay After RD Low2
tRDYPRD
REDY (O/D) or (A/D) Low Pulse Width for Read
tHDARWH
Data Disable After RD High3
Min
5 V and 3.3 V
Max
0
0
6
0
0
Unit
ns
ns
ns
ns
ns
2
10
45 + 21DT/16
2
8
ns
ns
ns
ns
1
Not required if RD and address are valid tHBGRCSV after HBG goes low. For first access after HBR asserted, ADDR31-0 must be a non-MMS value 1/2 tCLK before RD or WR goes
low or by tHBGRCSV after HBG goes low. This is easily accomplished by driving an upper address signal high when HBG is asserted. See the “Host Processor Control of the
ADSP-2106x” section in the ADSP-2106x SHARC User’s Manual, Revision 2.1.
2
For ADSP-21060L, specification is 10.5 ns max; for ADSP-21060LC, specification is 12.5 ns max.
3
For ADSP-21060L/ADSP-21060LC, specification is 2 ns min, 8.5 ns max.
Table 20. Write Cycle
Parameter
Timing Requirements
tSCSWRL
CS Low Setup Before WR Low
tHCSWRH
CS Low Hold After WR High
tSADWRH
Address Setup Before WR High
Address Hold After WR High
tHADWRH
tWWRL
WR Low Width
tWRWH
RD/WR High Width
tDWRHRDY
WR High Delay After REDY (O/D) or (A/D) Disable
tSDATWH
Data Setup Before WR High
tHDATWH
Data Hold After WR High
Switching Characteristics
REDY (O/D) or (A/D) Low Delay After WR/CS Low
tDRDYWRL
tRDYPWR
REDY (O/D) or (A/D) Low Pulse Width for Write
tSRDYCK
REDY (O/D) or (A/D) Disable to CLKIN
Rev. H |
Page 33 of 64 |
Min
5 V and 3.3 V
Max
0
0
5
2
7
6
0
5
1
ns
ns
ns
ns
ns
ns
ns
ns
ns
10
15 + 7DT/16
1 + 7DT/16
March 2013
Unit
8 + 7DT/16
ns
ns
ns
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
CLKIN
t SR D YC K
REDY (O/D)
REDY (A/D)
O/D = OPEN DRAIN, A/D = ACTIVE DRIVE
Figure 19. Synchronous REDY Timing
READ CYCLE
ADDRESS/CS
tH AD R D H
tS A DR D L
tW RW H
RD
tH DA R WH
DATA (OUT)
tD R D H RD Y
tSD ATR DY
t DR DY R DL
tR D YPR D
REDY (O /D )
REDY (A/D)
WRITE CYCLE
ADDRESS
tSA D WR H
tS C SWR L
tH A D WR H
tH CS WR H
CS
tW WR L
tWR WH
WR
tH D ATWH
tS DA TWH
DATA (IN)
tD WR H R DY
tD R D YWR L
tR DYP WR
REDY (O/D)
REDY (A/D)
O/D = OPEN DRAIN, A/D = ACTIVE DRIVE
Figure 20. Asynchronous Read/Write—Host to ADSP-2106x
Rev. H |
Page 34 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Three-State Timing—Bus Master, Bus Slave
These specifications show how the memory interface is disabled
(stops driving) or enabled (resumes driving) relative to CLKIN
and the SBTS pin. This timing is applicable to bus master transition cycles (BTC) and host transition cycles (HTC) as well as the
SBTS pin.
Table 21. Three-State Timing—Bus Master, Bus Slave
Parameter
Timing Requirements
tSTSCK
SBTS Setup Before CLKIN
tHTSCK
SBTS Hold Before CLKIN
Switching Characteristics
Address/Select Enable After CLKIN1
tMIENA
tMIENS
Strobes Enable After CLKIN2
tMIENHG
HBG Enable After CLKIN
tMITRA
Address/Select Disable After CLKIN3
tMITRS
Strobes Disable After CLKIN2
tMITRHG
HBG Disable After CLKIN
Data Enable After CLKIN4
tDATEN
tDATTR
Data Disable After CLKIN4
tACKEN
ACK Enable After CLKIN4
tACKTR
ACK Disable After CLKIN4
tADCEN
ADRCLK Enable After CLKIN
tADCTR
ADRCLK Disable After CLKIN
tMTRHBG
Memory Interface Disable Before HBG Low5
Memory Interface Enable After HBG High5
tMENHBG
Min
5 V and 3.3 V
Max
12 + DT/2
6 + DT/2
–1.5 – DT/8
–1.5 – DT/8
–1.5 – DT/8
0 – DT/4
1.5 – DT/4
2.0 – DT/4
9 + 5DT/16
0 – DT/8
7.5 + DT/4
–1 – DT/8
–2 – DT/8
7 – DT/8
6 – DT/8
8 – DT/4
0 + DT/8
19 + DT
1
For ADSP-21060L/ADSP-21060LC/ADSP-21062L, specification is –1.25 – DT/8 ns min, for ADSP-21062, specification is –1 – DT/8 ns min.
Strobes = RD, WR, PAGE, DMAG, BMS, SW.
3
For ADSP-21060LC, specification is 0.25 – DT/4 ns max.
4
In addition to bus master transition cycles, these specs also apply to bus master and bus slave synchronous read/write.
5
Memory Interface = Address, RD, WR, MSx, SW, PAGE, DMAGx, and BMS (in EPROM boot mode).
2
HBG
tMTRHBG
tMENHBG
MEMORY
INTERFACE
MEMORY INTERFACE = ADDRESS, RD, WR, MSx, SW, PAGE, DMAGx. BMS (IN EPROM BOOT MODE)
Figure 21. Three-State Timing (Bus Transition Cycle, SBTS Assertion)
Rev. H |
Page 35 of 64 |
March 2013
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
CLKIN
tSTSCK
tHTSCK
SBTS
tMIENA, tMIENS, tMIENHG
tMITRA, tMITRS, tMITRHG
MEMORY
INTERFACE
tDATTR
tDATEN
DATA
tACKTR
tACKEN
ACK
tADCEN
tADCTR
ADRCLK
Figure 22. Three-State Timing (Bus Transition Cycle, SBTS Assertion)
Rev. H |
Page 36 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
DMA Handshake
These specifications describe the three DMA handshake modes.
In all three modes, DMARx is used to initiate transfers. For
Handshake mode, DMAGx controls the latching or enabling of
data externally. For External handshake mode, the data transfer
is controlled by the ADDR31–0, RD, WR, PAGE, MS3–0, ACK,
and DMAGx signals. For Paced Master mode, the data transfer
is controlled by ADDR31–0, RD, WR, MS3–0, and ACK (not
DMAG). For Paced Master mode, the Memory Read-Bus Master, Memory Write-Bus Master, and Synchronous Read/WriteBus Master timing specifications for ADDR31–0, RD, WR,
MS3–0, PAGE, DATA63–0, and ACK also apply.
Table 22. DMA Handshake
Parameter
Min
Timing Requirements
tSDRLC
DMARx Low Setup Before CLKIN1
5
tSDRHC
DMARx High Setup Before CLKIN1
5
tWDR
DMARx Width Low (Nonsynchronous)
6
Data Setup After DMAGx Low2
tSDATDGL
tHDATIDG
Data Hold After DMAGx High
2
tDATDRH
Data Valid After DMARx High2
tDMARLL
DMARx Low Edge to Low Edge
23 + 7DT/8
2
tDMARH
DMARx Width High
6
Switching Characteristics
tDDGL
DMAGx Low Delay After CLKIN
9 + DT/4
tWDGH
DMAGx High Width
6 + 3DT/8
tWDGL
DMAGx Low Width
12 + 5DT/8
tHDGC
DMAGx High Delay After CLKIN
–2 – DT/8
3
tVDATDGH
Data Valid Before DMAGx High
8 + 9DT/16
tDATRDGH
Data Disable After DMAGx High4
0
tDGWRL
WR Low Before DMAGx Low5
0
DMAGx Low Before WR High
10 + 5DT/8 +W
tDGWRH
tDGWRR
WR High Before DMAGx High
1 + DT/16
tDGRDL
RD Low Before DMAGx Low
0
tDRDGH
RD Low Before DMAGx High
11 + 9DT/16 + W
tDGRDR
RD High Before DMAGx High
0
tDGWR
DMAGx High to WR, RD, DMAGx Low
5 + 3DT/8 + HI
Address/Select Valid to DMAGx High
17 + DT
tDADGH
6
tDDGHA
Address/Select Hold After DMAGx High
–0.5
W = (number of wait states specified in WAIT register) × tCK.
HI = tCK (if data bus idle cycle occurs, as specified in WAIT register; otherwise HI = 0).
1
5 V and 3.3 V
Max
10 + 5DT/8
16 + 7DT/8
15 + DT/4
6 – DT/8
7
2
3 + DT/16
2
3
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Only required for recognition in the current cycle.
tSDATDGL is the data setup requirement if DMARx is not being used to hold off completion of a write. Otherwise, if DMARx low holds off completion of the write, the data can
be driven tDATDRH after DMARx is brought high.
3
tVDATDGH is valid if DMARx is not being used to hold off completion of a read. If DMARx is used to prolong the read, then tVDATDGH = tCK – 0.25tCCLK – 8 + (n × tCK) where n equals
the number of extra cycles that the access is prolonged.
4
See Example System Hold Time Calculation on Page 48 for calculation of hold times given capacitive and dc loads.
5
For ADSP-21062/ADSP-21062L specification is –2.5 ns min, 2 ns max.
6
For ADSP-21060L/ADSP-21062L specification is –1 ns min.
2
Rev. H |
Page 37 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
CLKIN
tSDRLC
tDMARLL
tSDRHC
tWDR
tDMARH
DMARx
tHDGC
tDDGL
tWDGL
tWDGH
DMAGx
TRANSFERS BETWEEN ADSP-2106x
INTERNAL MEMORY AND EXTERNAL DEVICE
tDATRDGH
tVDATDGH
DATA
(OUT)
(FROM ADSP-2106x TO EXTERNAL DEVICE)
tDATDRH
tSDATDGL
DATA
(IN)
tHDATIDG
(FROM EXTERNAL DEVICE TO ADSP-2106x)
TRANSFERS BETWEEN EXTERNAL DEVICE AND
EXTERNAL MEMORY* (EXTERNAL HANDSHAKE MODE)
tDGWRL
WR
tDGWRH
tDGWRR
(EXTERNAL DEVICE TO EXTERNAL MEMORY)
tDGRDR
RD
tDGRDL
(EXTERNAL MEMORY TO EXTERNAL DEVICE)
tDRDGH
tDADGH
ADDR
MSx, SW
*MEMORY READ BUS MASTER, MEMORY WRITE BUS MASTER, OR SYNCHRONOUS READ/WRITE BUS MASTER
TIMING SPECIFICATIONS FOR ADDR31–0, RD, WR, SW MS3–0, AND ACK ALSO APPLY HERE.
Figure 23. DMA Handshake
Rev. H |
Page 38 of 64 |
March 2013
tDDGHA
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Link Ports —1 × CLK Speed Operation
Table 23. Link Ports—Receive
Parameter
Timing Requirements
tSLDCL
Data Setup Before LCLK Low1
Data Hold After LCLK Low
tHLDCL
tLCLKIW
LCLK Period (1 Operation)
tLCLKRWL
LCLK Width Low
tLCLKRWH
LCLK Width High
Switching Characteristics
tDLAHC
LACK High Delay After CLKIN High2, 3
LACK Low Delay After LCLK High
tDLALC
tENDLK
LACK Enable From CLKIN
tTDLK
LACK Disable From CLKIN
5V
Max
Min
3.3 V
Max
Min
3.5
3
tCK
6
5
3
3
tCK
6
5
18 + DT/2
–3
5 + DT/2
28.5 + DT/2
+13
Unit
ns
ns
ns
ns
ns
18 + DT/2
–3
5 + DT/2
28.5 + DT/2
+13
20 + DT/2
20 + DT/2
ns
ns
ns
ns
1
For ADSP-21062, specification is 3 ns min.
LACK goes low with tDLALC relative to rise of LCLK after first nibble, but does not go low if the receiver’s link buffer is not about to fill.
3
For ADSP-21060C, specification is 18 + DT/2 ns min, 29 + DT/2 ns max.
2
Table 24. Link Ports—Transmit
Parameter
Timing Requirements
tSLACH
LACK Setup Before LCLK High1
tHLACH
LACK Hold After LCLK High
Switching Characteristics
tDLCLK
Data Delay After CLKIN (1
Operation)2
tDLDCH
Data Delay After LCLK High3
Data Hold After LCLK High
tHLDCH
tLCLKTWL
LCLK Width Low4
tLCLKTWH
LCLK Width High5
tDLACLK
LCLK Low Delay After LACK High6
tENDLK
LACK Enable From CLKIN
tTDLK
LACK Disable From CLKIN
Min
5V
Max
18
–7
Min
3.3 V
Max
18
–7
15.5
3
–3
(tCK /2) – 2
(tCK /2) – 2
(tCK /2) + 8.5
5 + DT/2
(tCK /2) + 2
(tCK /2) + 2
(3 tCK /2) + 17
20 + DT/2
1
–3
(tCK /2) – 1
(tCK /2) – 1.25
(tCK /2) + 8
5 + DT/2
Unit
ns
ns
15.5
ns
2.5
ns
ns
ns
ns
ns
ns
ns
(tCK /2) + 1.25
(tCK /2) + 1
(3 tCK /2) + 17.5
20 + DT/2
For ADSP-21060L/ADSP-21060LC, specification is 20 ns min.
2
For ADSP-21060L, specification is 16.5 ns max; for ADSP-21060LC, specification is 16.75 ns max.
3
For ADSP-21062, specification is 2.5 ns max.
4
For ADSP-21062, specification is (tCK/2) – 1 ns min, (tCK/2) + 1.25 ns max; for ADSP-21062L, specification is (tCK/2) – 1 ns min, (tCK/2) + 1.5 ns max; for ADSP-21060LC
specification is (tCK/2) – 1 ns min, (tCK/2) + 2.25 ns max.
5
For ADSP-21062, specification is (tCK/2) – 1.25 ns min, (tCK/2) + 1 ns max; for ADSP-21062L, specification is (tCK/2) – 1.5 ns min, (tCK/2) + 1 ns max; for ADSP-21060C
specification is (tCK/2) – 2.25 ns min, (tCK/2) + 1 ns max.
6
For ADSP-21062, specification is (tCK/2) + 8.75 ns min, (3 × tCK/2) + 17 ns max; for ADSP-21062L, specification is (tCK/2) + 8 ns min, (3 × tCK/2) + 17 ns max; for
ADSP-21060LC specification is (tCK/2) + 8 ns min, (3 × tCK/2) + 18.5 ns max.
Rev. H |
Page 39 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Table 25. Link Port Service Request Interrupts: 1 and 2 Speed Operations
Parameter
Timing Requirements
tSLCK
LACK/LCLK Setup Before CLKIN Low1
tHLCK
LACK/LCLK Hold After CLKIN Low1
1
5V
Max
Min
10
2
Min
3.3 V
Max
10
2
Unit
ns
ns
Only required for interrupt recognition in the current cycle.
Link Ports —2 × CLK Speed Operation
Hold skew is the maximum delay that can be introduced in
LCLK relative to LDATA:
Calculation of link receiver data setup and hold relative to link
clock is required to determine the maximum allowable skew
that can be introduced in the transmission path between
LDATA and LCLK. Setup skew is the maximum delay that can
be introduced in LDATA relative to LCLK:
Hold Skew = tLCLKTWL min – tHLDCH – tHLDCL
Calculations made directly from 2 speed specifications will
result in unrealistically small skew times because they include
multiple tester guardbands.
Setup Skew = tLCLKTWH min – tDLDCH – tSLDCL
Note that link port transfers at 2× CLK speed at 40 MHz
(tCK = 25 ns) may fail. However, 2× CLK speed link port transfers at 33 MHz (tCK = 30 ns) work as specified.
Table 26. Link Ports—Receive
Parameter
Timing Requirements
tSLDCL
Data Setup Before LCLK Low
tHLDCL
Data Hold After LCLK Low
tLCLKIW
LCLK Period (2 Operation)
tLCLKRWL
LCLK Width Low1
LCLK Width High2
tLCLKRWH
Switching Characteristics
tDLAHC
LACK High Delay After CLKIN High3
tDLALC
LACK Low Delay After LCLK High4
Min
5V
Max
2.5
2.25
tCK/2
4.5
4.25
18 + DT/2
6
Min
3.3 V
Max
2.25
2.25
tCK/2
5.25
4
28.5 + DT/2
16
1
18 + DT/2
6
Unit
ns
ns
ns
ns
ns
29.5 + DT/2
16
ns
ns
For ADSP-21060L, specification is 5 ns min.
For ADSP-21062, specification is 4 ns min, for ADSP-21060LC, specification is 4.5 ns min.
3
LACK goes low with tDLALC relative to rise of LCLK after first nibble, but does not go low if the receiver’s link buffer is not about to fill.
4
For ADSP-21060L, specification is 6 ns min, 18 ns max. For ADSP-21060C, specification is 6 ns min, 16.5 ns max. For ADSP-21060LC, specification is 6 ns min, 18.5 ns max.
2
Rev. H |
Page 40 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Table 27. Link Ports—Transmit
Parameter
Timing Requirements
tSLACH
LACK Setup Before LCLK High
tHLACH
LACK Hold After LCLK High
Switching Characteristics
tDLCLK
Data Delay After CLKIN
tDLDCH
Data Delay After LCLK High1
tHLDCH
Data Hold After LCLK High2
tLCLKTWL
LCLK Width Low3
LCLK Width High4
tLCLKTWH
tDLACLK
LCLK Low Delay After LACK High
Min
5V
Max
19
–6.75
Min
19
–6.5
8
2.25
–2.0
(tCK /4) – 1
(tCK /4) – 1.25
(tCK /4) + 9
3.3 V
Max
(tCK /4) + 1.25
(tCK /4) + 1
(3 tCK /4) + 16.5
1
ns
ns
8
2.25
–2
(tCK /4) – 0.75
(tCK /4) – 1.5
(tCK /4) + 9
Unit
(tCK /4) + 1.5
(tCK /4) + 1
(3 tCK /4) + 16.5
ns
ns
ns
ns
ns
ns
For ADSP-21060/ADSP-21060C, specification is 2.5 ns max.
For ADSP-21062L, specification is –2.25 ns min.
3
For ADSP-21060, specification is (tCK/4) – 1 ns min, (tCK/4) + 1 ns max; for ADSP-21060C/ADSP-21062L, specification is (tCK/4) – 1 ns min, (tCK/4) + 1.5 ns max.
4
For ADSP-21060, specification is (tCK/4) – 1 ns min, (tCK/4) + 1 ns max; for ADSP-21060C, specification is (tCK/4) – 1.5 ns min, (tCK/4) + 1 ns max.
2
Rev. H |
Page 41 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
TRANSMIT
CLKIN
tDLCLK
tLCLKTWH
tLCLKTWL
LAST NIBBLE
TRANSMITTED
FIRST NIBBLE
TRANSMITTED
LCLK 1x
OR
LCLK 2x
LCLK INACTIVE
(HIGH)
tDLDCH
tHLDCH
LDAT(3:0)
OUT
tDLACLK
tSLACH
tHLACH
LACK (IN)
THE tSLACH REQUIREMENT APPLIES TO THE RISING EDGE OF LCLK ONLY FOR THE FIRST NIBBLE TRANSMITTED.
RECEIVE
CLKIN
tLCLKIW
tLCLKRWH
tLCLKRWL
LCLK 1x
OR
LCLK 2x
tHLDCL
tSLDCL
LDAT(3:0)
IN
tDLALC
tDLAHC
LACK (OUT)
LINK PORT ENABLE/THREE-STATE DELAY FROM INSTRUCTION
CLKIN
tENDLK
t TDLK
LCLK
LDAT(3:0)
LACK
LINK PORT ENABLE OR THREE-STATE TAKES EFFECT 2 CYCLES AFTER A WRITE TO A LINK PORT CONTROL REGISTER.
LINK PORT INTERRUPT SETUP TIME
CLKIN
tSLCK
t HLCK
LCLK
LACK
Figure 24. Link Ports—Receive
Rev. H |
Page 42 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Serial Ports
For serial ports, see Table 28, Table 29, Table 30, Table 31,
Table 32, Table 33, Table 35, Figure 26, and Figure 25. To determine whether communication is possible between two devices
at clock speed n, the following specifications must be confirmed:
1) frame sync delay and frame sync setup and hold, 2) data delay
and data setup and hold, and 3) SCLK width.
Table 28. Serial Ports—External Clock
Parameter
Min
Timing Requirements
tSFSE
TFS/RFS Setup Before TCLK/RCLK1
tHFSE
TFS/RFS Hold After TCLK/RCLK1, 2
tSDRE
Receive Data Setup Before RCLK1
tHDRE
Receive Data Hold After RCLK1
tSCLKW
TCLK/RCLK Width3
TCLK/RCLK Period
tSCLK
3.5
4
1.5
6.5
9
tCK
5 V and 3.3 V
Max
Unit
ns
ns
ns
ns
ns
ns
1
Referenced to sample edge.
RFS hold after RCK when MCE = 1, MFD = 0 is 0 ns minimum from drive edge. TFS hold after TCK for late external TFS is 0 ns minimum from drive edge.
3
For ADSP-21060/ADSP-21060C/ADSP-21060LC, specification is 9.5 ns min.
2
Table 29. Serial Ports—Internal Clock
1
2
Parameter
Min
Timing Requirements
tSFSI
TFS Setup Before TCLK1; RFS Setup Before RCLK1
tHFSI
TFS/RFS Hold After TCLK/RCLK1, 2
tSDRI
Receive Data Setup Before RCLK1
tHDRI
Receive Data Hold After RCLK1
8
1
3
3
5 V and 3.3 V
Max
Unit
ns
ns
ns
ns
Referenced to sample edge.
RFS hold after RCK when MCE = 1, MFD = 0 is 0 ns minimum from drive edge. TFS hold after TCK for late external TFS is 0 ns minimum from drive edge.
Table 30. Serial Ports—External or Internal Clock
1
Parameter
Min
Switching Characteristics
tDFSE
RFS Delay After RCLK (Internally Generated RFS)1
tHOFSE
RFS Hold After RCLK (Internally Generated RFS)1
3
5 V and 3.3 V
Max
13
Unit
ns
ns
Referenced to drive edge.
Table 31. Serial Ports—External Clock
1
Parameter
Min
Switching Characteristics
tDFSE
TFS Delay After TCLK (Internally Generated TFS)1
tHOFSE
TFS Hold After TCLK (Internally Generated TFS)1
tDDTE
Transmit Data Delay After TCLK1
tHDTE
Transmit Data Hold After TCLK1
3
13
16
5
Referenced to drive edge.
Rev. H |
Page 43 of 64 |
5 V and 3.3 V
Max
March 2013
Unit
ns
ns
ns
ns
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Table 32. Serial Ports—Internal Clock
Parameter
Switching Characteristics
tDFSI
TFS Delay After TCLK (Internally Generated TFS)1
TFS Hold After TCLK (Internally Generated TFS)1
tHOFSI
tDDTI
Transmit Data Delay After TCLK1
tHDTI
Transmit Data Hold After TCLK1
tSCLKIW
TCLK/RCLK Width2
1
2
Min
Max
Unit
4.5
0
0.5tSCLK –2.5
0.5tSCLK +2.5
ns
ns
ns
ns
ns
Min
Max
Unit
–1.5
7.5
Referenced to drive edge.
For ADSP-21060L/ADSP-21060C, specification is 0.5TSCLK – 2 ns min, 0.5tSCLK + 2 ns max.
Table 33. Serial Ports—Enable and Three-State
Parameter
Switching Characteristics
tDDTEN
Data Enable from External TCLK1, 2
Data Disable from External TCLK1, 3
tDDTTE
tDDTIN
Data Enable from Internal TCLK1
tDDTTI
Data Disable from Internal TCLK1, 4
tDCLK
TCLK/RCLK Delay from CLKIN
tDPTR
SPORT Disable After CLKIN
4
3
22 + 3 DT/8
17
ns
ns
ns
ns
ns
ns
Max
Unit
tCK/2
ns
ns
Max
Unit
12
ns
10.5
0
1
Referenced to drive edge.
For ADSP-21060L/ADSP-21060C, specification is 3.5 ns min; for ADSP-21062 specification is 4.5 ns min.
3
For ADSP-21062L, specification is 16 ns max.
4
For ADSP-21062L, specification is 7.5 ns max.
2
Table 34. Serial Ports—GATED SCLK with External TFS (Mesh Multiprocessing)1
Parameter
Switching Characteristics
tSTFSCK
TFS Setup Before CLKIN
tHTFSCK
TFS Hold After CLKIN
1
Min
4
Applies only to gated serial clock mode used for serial port system I/O in mesh multiprocessing systems.
Table 35. Serial Ports—External Late Frame Sync
Parameter
Switching Characteristics
tDDTLFSE
Data Delay from Late External TFS or External RFS with MCE = 1,
MFD = 01, 2
tDDTENFS
Data Enable from Late FS or MCE = 1, MFD = 01, 3
1
Min
3.5
MCE = 1, TFS enable and TFS valid follow tDDTLFSE and tDDTENFS.
2
For ADSP-21062/ADSP-21062L, specification is 12.75 ns max; for ADSP-21060L/ADSP-21060LC, specification is 12.8 ns max.
3
For ADSP-21060/ADSP-21060C, specification is 3 ns min.
Rev. H |
Page 44 of 64 |
March 2013
ns
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
DATA RECEIVE— INTERNAL CLOCK
DRIVE
EDGE
DATA RECEIVE— EXTERNAL CLOCK
DRIVE
EDGE
SAMPLE
EDGE
SAMPLE
EDGE
tSCLKW
tSCLKIW
RCLK
RCLK
tDFSE
tDFSE
tSFSI
tHOFSE
tHOFSE
tHFSI
RFS
tSFSE
tHFSE
tSDRE
tHDRE
RFS
tSDRI
tHDRI
DR
DR
NOTE: EITHER THE RISING EDGE OR FALLING EDGE OF RCLK, TCLK CAN BE USED AS THE ACTIVE SAMPLING EDGE.
DATA TRANSMIT— INTERNAL CLOCK
DRIVE
EDGE
DATA TRANSMIT— EXTERNAL CLOCK
SAMPLE
EDGE
tSCLKIW
DRIVE
EDGE
SAMPLE
EDGE
tSCLKW
TCLK
TCLK
tDFSE
tDFSI
tHOFSI
tSFSI
tHFSI
tHOFSE
TFS
tSFSE
tHFSE
TFS
tDDTI
tDDTE
tHDTE
tHDTI
DT
DT
NOTE: EITHER THE RISING EDGE OR FALLING EDGE OF RCLK, TCLK CAN BE USED AS THE ACTIVE SAMPLING EDGE.
DRIVE EDGE
DRIVE EDGE
TCLK/RCLK
TCLK
(EXT)
tDDTTE
tDDTEN
DT
DRIVE
EDGE
TCLK
(INT)
DRIVE
EDGE
TCLK/RCLK
tDDTIN
tDDTTI
DT
CLKIN
CLKIN
tHTFSCK
tDPTR
TCLK, RCLK
TFS, RFS, DT
TCLK (INT)
RCLK (INT)
SPORT DISABLE DELAY
FROM INSTRUCTION
SPORT ENABLE AND
THREE-STATE
LATENCY
IS TWO CYCLES
tDCLK
tSTFSCK
TFS (EXT)
NOTE: APPLIES ONLY TO GATED SERIAL CLOCK MODE WITH
EXTERNAL TFS, AS USED IN THE SERIAL PORT SYSTEM I/O
FOR MESH MULTIPROCESSING.
LOW TO HIGH ONLY
Figure 25. Serial Ports
Rev. H |
Page 45 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
EXTERNAL RFS WITH MCE = 1, MFD = 0
DRIVE
SAMPLE
DRIVE
RCLK
tSFSE/I
tHOFSE/I
RFS
DT
tDDTE/I
tHDTE/I
tDDTENFS
1ST BIT
2ND BIT
tDDTLFSE
LATE EXTERNAL TFS
DRIVE
SAMPLE
DRIVE
TCLK
tHOFSE/I
tSFSE/I
TFS
tDDTE/I
TDDTENFS
tHDTE/I
1ST BIT
DT
2ND BIT
tDDTLFSE
Figure 26. Serial Ports—External Late Frame Sync
Rev. H |
Page 46 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
JTAG Test Access Port and Emulation
For JTAG Test Access Port and Emulation, see Table 36 and
Figure 27.
Table 36. JTAG Test Access Port and Emulation
Parameter
Timing Requirements
tTCK
TCK Period
tSTAP
TDI, TMS Setup Before TCK High
tHTAP
TDI, TMS Hold After TCK High
tSSYS
System Inputs Setup Before TCK Low1
System Inputs Hold After TCK Low1, 2
tHSYS
tTRSTW
TRST Pulse Width
Switching Characteristics
tDTDO
TDO Delay from TCK Low
tDSYS
System Outputs Delay After TCK Low3
Min
Max
tCK
5
6
7
18
4tCK
Unit
ns
ns
ns
ns
ns
ns
13
18.5
1
ns
ns
System Inputs = DATA63–0, ADDR31–0, RD, WR, ACK, SBTS, HBR, HBG, CS, DMAR1, DMAR2, BR6–1, ID2–0, RPBA, IRQ2–0, FLAG3–0, PA, BRST, DR0, DR1, TCLK0,
TCLK1, RCLK0, RCLK1, TFS0, TFS1, RFS0, RFS1, LxDAT7–0, LxCLK, LxACK, EBOOT, LBOOT, BMS, CLKIN, RESET.
2
For ADSP-21060L/ADSP-21060LC/ADSP-21062L, specification is 18.5 ns min.
3
System Outputs = DATA63–0, ADDR31–0, MS3–0, RD, WR, ACK, PAGE, CLKOUT, HBG, REDY, DMAG1, DMAG2, BR6–1, PA, BRST, CIF, FLAG3–0, TIMEXP, DT0,
DT1, TCLK0, TCLK1, RCLK0, RCLK1, TFS0, TFS1, RFS0, RFS1, LxDAT7–0, LxCLK, LxACK, BMS.
tTCK
TCK
tSTAP
tHTAP
TMS
TDI
tDTDO
TDO
tSSYS
SYSTEM
INPUTS
tDSYS
SYSTEM
OUTPUTS
Figure 27. JTAG Test Access Port and Emulation
Rev. H |
Page 47 of 64 |
March 2013
tHSYS
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
TEST CONDITIONS
For the ac signal specifications (timing parameters), see Timing
Specifications on Page 21. These specifications include output
disable time, output enable time, and capacitive loading. The
timing specifications for the DSP apply for the voltage reference
levels in Figure 28.
INPUT
OR
OUTPUT
1.5V
1.5V
Figure 28. Voltage Reference Levels for AC Measurements (Except Output
Enable/Disable)
Output Disable Time
Output pins are considered to be disabled when they stop driving, go into a high impedance state, and start to decay from their
output high or low voltage. The time for the voltage on the bus
to decay by V is dependent on the capacitive load, CL, and the
load current, IL. This decay time can be approximated by the following equation:
L V
P EXT = C
------------IL
output has reached a specified high or low trip point, as shown
in the Output Enable/Disable diagram (Figure 29). If multiple
pins (such as the data bus) are enabled, the measurement value
is that of the first pin to start driving.
Example System Hold Time Calculation
To determine the data output hold time in a particular system,
first calculate tDECAY using the equation given above. Choose V
to be the difference between the ADSP-2106x’s output voltage
and the input threshold for the device requiring the hold time. A
typical V will be 0.4 V. CL is the total bus capacitance (per data
line), and IL is the total leakage or three-state current (per data
line). The hold time will be tDECAY plus the minimum disable
time (i.e., tDATRWH for the write cycle).
Capacitive Loading
Output delays and holds are based on standard capacitive loads:
50 pF on all pins (see Figure 30). The delay and hold specifications given should be derated by a factor of 1.5 ns/50 pF for
loads other than the nominal value of 50 pF. Figure 32,
Figure 33, Figure 37, and Figure 38 show how output rise time
varies with capacitance. Figure 34 and Figure 36 show
graphically how output delays and holds vary with load capacitance. (Note that this graph or derating does not apply to output
disable delays; see the previous section Output Disable Time
under Test Conditions.) The graphs of Figure 32, Figure 33,
Figure 37, and Figure 38 may not be linear outside the ranges
shown.
The output disable time tDIS is the difference between
tMEASURED and tDECAY as shown in Figure 29. The time tMEASURED is
the interval from when the reference signal switches to when the
output voltage decays V from the measured output high or
output low voltage. tDECAY is calculated with test loads CL and IL,
and with V equal to 0.5 V.
IOL
TO
OUTPUT
PIN
+1.5V
50pF
REFERENCE
SIGNAL
tMEASURED
tDIS
tENA
VOH (MEASURED)
VOL (MEASURED)
VOH (MEASURED) - ⌬V
2.0V
VOL (MEASURED) + ⌬V
1.0V
tDECAY
OUTPUT STOPS
DRIVING
IOH
VOH (MEASURED)
Figure 30. Equivalent Device Loading for AC Measurements (Includes All
Fixtures)
VOL (MEASURED)
Output Drive Characteristics
OUTPUT STARTS
DRIVING
Figure 31 shows typical I-V characteristics for the output drivers of the ADSP-2106x. The curves represent the current drive
capability of the output drivers as a function of output voltage.
HIGH IMPEDANCE STATE.
TEST CONDITIONS CAUSE
THIS VOLTAGE TO BE
APPROXIMATELY 1.5V
Figure 29. Output Enable/Disable
Output Enable Time
Output pins are considered to be enabled when they have made
a transition from a high impedance state to when they start driving. The output enable time tENA is the interval from when a
reference signal reaches a high or low voltage level to when the
Rev. H |
Page 48 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Output Characteristics (5 V)
3.5
RISE AND FALL TIMES - ns (0.8V to 2.0V)
75
SOURCE CURRENT - mA
50
25
5.25V, -40°C
5.0V, +25°C
0
4.75V, +100°C
-25
4.75V,+100°C
-50
5.0V, +25°C
-75
5.25V, -40°C
-100
-125
-150
0
2.5
RISE TIME
2.0
Y = 0.009x + 1.1
1.5
FALL TIME
1.0
Y = 0.005x + 0.6
0.5
0
0.75
1.50
2.25
3.00
3.75
SOURCE VOLTAGE - V
4.50
0
5.25
20
40
60
80
100 120 140
LOAD CAPACITANCE - pF
160
180
200
Figure 33. Typical Output Rise Time (0.8 V to 2.0 V) vs. Load Capacitance
(VDD = 5 V)
Figure 31. ADSP-21062 Typical Output Drive Currents (VDD = 5 V)
5
16.0
OUTPUT DELAY OR HOLD - ns
14.0
RISE AND FALL TIMES - ns
(0.5V to 4.5V, 10% to 90%)
3.0
12.0
RISE TIME
10.0
Y = 0.005x + 3.7
8.0
FALL TIME
6.0
4.0
Y = 0.03x - 1.45
4
3
2
1
NOMINAL
2.0
0
Y = 0.0031x + 1.1
-1
0
20
40
60
80
100 120 140
LOAD CAPACITANCE - pF
160
180
25
200
Figure 32. Typical Output Rise Time (10% to 90% VDD) vs. Load Capacitance
(VDD = 5 V)
Rev. H |
50
75
100
125
150
LOAD CAPACITANCE - pF
175
200
Figure 34. Typical Output Delay or Hold vs. Load Capacitance (at Maximum
Case Temperature) (VDD = 5 V)
Page 49 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Output Characteristics (3.3 V)
120
18
3.3V, +25°C
80
SOURCE CURRENT - mA
RISE AND FALL TIMES - ns (10% to 90%)
100
3.6V, -40°C
60
40
3.0V, +85°C
VOH
20
0
3.0V, +85°C
-20
3.3V, +25°C
-40
3.6V, -40°C
-60
-80
16
14
Y = 0.0796x + 1.17
12
10
RISE TIME
8
6
0
-120
0
0.5
1.0
1.5
2.0
2.5
SOURCE VOLTAGE - V
3.0
0
3.5
20
40
60
80
100
120
140
160
180
200
LOAD CAPACITANCE - pF
Figure 37. Typical Output Rise Time (10% to 90% VDD) vs. Load Capacitance
(VDD = 3.3 V)
Figure 35. ADSP-21062 Typical Output Drive Currents (VDD = 3.3 V)
5
9
RISE AND FALL TIMES - ns (0.8V to 2.0V)
OUTPUT DELAY OR HOLD - ns
FALL TIME
2
VOL
-100
Y = 0.0467x + 0.55
4
4
3
Y = 0.0329x - 1.65
2
1
NOMINAL
-1
25
50
75
100
125
150
LOAD CAPACITANCE - pF
175
8
7
5
RISE TIME
4
Y = 0.0305x + 0.24
3
FALL TIME
2
1
0
200
Y = 0.0391x + 0.36
6
0
20
40
60
80
100
120
140
160
180
200
LOAD CAPACITANCE - pF
Figure 36. Typical Output Delay or Hold vs. Load Capacitance (at Maximum
Case Temperature) (VDD = 3.3 V)
Rev. H |
Page 50 of 64 |
Figure 38. Typical Output Rise Time (0.8 V to 2.0 V) vs. Load Capacitance
(VDD = 3.3 V)
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
ENVIRONMENTAL CONDITIONS
Thermal Characteristics for CQFP Package
The ADSP-2106x processors are rated for performance under
TCASE environmental conditions specified in the Operating Conditions (5 V) on Page 15 and Operating Conditions (3.3 V) on
Page 18.
The ADSP-21060C/ADSP-21060LC are available in 240-lead
thermally enhanced ceramic QFP (CQFP). There are two package versions, one with a copper/tungsten heat slug on top of the
package (CZ) for air cooling, and one with the heat slug on the
bottom (CW) for cooling through the board. The ADSP-2106x
is specified for a case temperature (TCASE). To ensure that the
TCASE data sheet specification is not exceeded, a heatsink and/or
an air flow source may be used. A heatsink should be attached
with a thermal adhesive.
Thermal Characteristics for MQFP_PQ4 and PBGA
Packages
The ADSP-21060/ADSP-21060L and ADSP-21062/ADSP21062L are available in 240-lead thermally enhanced
MQFP_PQ4 and 225-ball plastic ball grid array packages. The
top surface of the thermally enhanced MQFP_PQ4 contains a
metal slug from which most of the die heat is dissipated. The
slug is flush with the top surface of the package. Note that the
metal slug is internally connected to GND through the device
substrate.
Both packages are specified for a case temperature (TCASE). To
ensure that the TCASE is not exceeded, a heatsink and/or an airflow source may be used. A heatsink should be attached with a
thermal adhesive.
TCASE = TAMB + (PD CA)
TCASE = TAMB + (PD CA)
TCASE = Case temperature (measured on top surface of package)
TAMB = Ambient temperature C
PD = Power dissipation in W (this value depends upon the specific application; a method for calculating PD is shown under
Power Dissipation).
CA =Value from Table 39 below.
Table 39. Thermal Characteristics for Thermally Enhanced
240-Lead CQFP1
Parameter
Airflow (LFM2)
ADSP-21060CW/ADSP-21060LCW
CA
0
CA
100
CA
200
CA
400
CA
600
ADSP-21060CZ/ADSP-21060LCZ
CA
0
CA
100
CA
200
CA
400
CA
600
TCASE = Case temperature (measured on top surface of package)
TAMB = Ambient temperature C
PD =Power dissipation in W (this value depends upon the specific application; a method for calculating PD is shown under
Power Dissipation).
CA =Values from Table 37 and Table 38 below.
Table 37. Thermal Characteristics for Thermally Enhanced
240-Lead MQFP_PQ41
Parameter
CA
CA
CA
CA
CA
Airflow (LFM2)
0
100
200
400
600
Typical
10
9
8
7
6
Unit
°C/W
°C/W
°C/W
°C/W
°C/W
1
This represents thermal resistance at total power of 5 W. With airflow, no
variance is seen in CA at 5 W.
CA at 0 LFM varies with power:
at 2 W, CA = 14°C/W
at 3 W, CA = 11°C/W
2
LFM = Linear feet per minute of airflow.
Table 38. Thermal Characteristics for BGA
Parameter
CA
CA
CA
1
Airflow (LFM1)
0
200
400
Typical
20.70
15.30
12.90
1
Unit
19.5
16
14
12
10
°C/W
°C/W
°C/W
°C/W
°C/W
20
16
14
11.5
9.5
°C/W
°C/W
°C/W
°C/W
°C/W
This represents thermal resistance at total power of 5 W. With airflow, no
variance is seen in CA at 5W.
CA at 0 LFM varies with power.
ADSP-21060CW/ADSP-21060LCW:
at 2 W, CA = 23°C/W
at 3 W, CA = 21.5°C/W
ADSP-21060CZ/ADSP-21060LCZ:
at 2 W, CA = 24°C/W
at 3 W, CA = 21.5°C/W
JC = 0.24°C/W for all CQFP models.
2
LFM = Linear feet per minute of airflow.
Unit
°C/W
°C/W
°C/W
LFM = Linear feet per minute of airflow.
Rev. H |
Typical
Page 51 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
225-BALL PBGA BALL CONFIGURATION
Table 40. ADSP-2106x 225-Ball Metric PBGA Ball Assignments (B-225-2)
Ball Name
BMS
ADDR30
DMAR2
DT1
RCLK1
TCLK0
RCLK0
ADRCLK
CS
CLKIN
PAGE
BR3
DATA47
DATA44
DATA42
MS0
SW
ADDR31
HBR
DR1
DT0
DR0
REDY
RD
ACK
BR6
BR2
DATA45
DATA43
DATA39
MS3
MS1
ADDR28
SBTS
TCLK1
RFS1
TFS0
RFS0
WR
DMAG1
BR4
DATA46
DATA41
DATA38
DATA36
Ball
Number
A01
A02
A03
A04
A05
A06
A07
A08
A09
A10
A11
A12
A13
A14
A15
B01
B02
B03
B04
B05
B06
B07
B08
B09
B10
B11
B12
B13
B14
B15
C01
C02
C03
C04
C05
C06
C07
C08
C09
C10
C11
C12
C13
C14
C15
Ball Name
ADDR25
ADDR26
MS2
ADDR29
DMAR1
TFS1
CPA
HBG
DMAG2
BR5
BR1
DATA40
DATA37
DATA35
DATA34
ADDR21
ADDR22
ADDR24
ADDR27
GND
GND
GND
GND
GND
GND
NC
DATA33
DATA30
DATA32
DATA31
ADDR17
ADDR18
ADDR20
ADDR23
GND
GND
VDD
VDD
VDD
GND
GND
DATA29
DATA26
DATA28
DATA27
Ball
Number
D01
D02
D03
D04
D05
D06
D07
D08
D09
D10
D11
D12
D13
D14
D15
E01
E02
E03
E04
E05
E06
E07
E08
E09
E10
E11
E12
E13
E14
E15
F01
F02
F03
F04
F05
F06
F07
F08
F09
F10
F11
F12
F13
F14
F15
Ball Name
ADDR14
ADDR15
ADDR16
ADDR19
GND
VDD
VDD
VDD
VDD
VDD
GND
DATA22
DATA25
DATA24
DATA23
ADDR12
ADDR11
ADDR13
ADDR10
GND
VDD
VDD
VDD
VDD
VDD
GND
DATA18
DATA19
DATA21
DATA20
ADDR9
ADDR8
ADDR7
ADDR4
GND
VDD
VDD
VDD
VDD
VDD
GND
DATA12
DATA15
DATA16
DATA17
Rev. H |
Ball
Number
G01
G02
G03
G04
G05
G06
G07
G08
G09
G10
G11
G12
G13
G14
G15
H01
H02
H03
H04
H05
H06
H07
H08
H09
H10
H11
H12
H13
H14
H15
J01
J02
J03
J04
J05
J06
J07
J08
J09
J10
J11
J12
J13
J14
J15
Page 52 of 64 |
Ball Name
ADDR6
ADDR5
ADDR3
ADDR0
ICSA
GND
VDD
VDD
VDD
GND
GND
DATA8
DATA11
DATA13
DATA14
ADDR2
ADDR1
FLAG0
FLAG3
RPBA
GND
GND
GND
GND
GND
NC
DATA4
DATA7
DATA9
DATA10
FLAG1
FLAG2
TIMEXP
TDI
LBOOT
L5ACK
L5DAT2
L4DAT2
L3DAT0
L2DAT3
L1DAT1
L0DAT0
DATA2
DATA5
DATA6
March 2013
Ball
Number
K01
K02
K03
K04
K05
K06
K07
K08
K09
K10
K11
K12
K13
K14
K15
L01
L02
L03
L04
L05
L06
L07
L08
L09
L10
L11
L12
L13
L14
L15
M01
M02
M03
M04
M05
M06
M07
M08
M09
M10
M11
M12
M13
M14
M15
Ball Name
EMU
TDO
IRQ0
IRQ1
ID2
L5DAT1
L4CLK
L3CLK
L3DAT3
L2DAT0
L1ACK
L1DAT3
L0DAT3
DATA1
DATA3
TRST
TMS
EBOOT
ID0
L5CLK
L5DAT3
L4DAT0
L4DAT3
L3DAT2
L2CLK
L2DAT2
L1DAT0
L0ACK
L0DAT1
DATA0
TCK
IRQ2
RESET
ID1
L5DAT0
L4ACK
L4DAT1
L3ACK
L3DAT1
L2ACK
L2DAT1
L1CLK
L1DAT2
L0CLK
L0DAT2
Ball
Number
N01
N02
N03
N04
N05
N06
N07
N08
N09
N10
N11
N12
N13
N14
N15
P01
P02
P03
P04
P05
P06
P07
P08
P09
P10
P11
P12
P13
P14
P15
R01
R02
R03
R04
R05
R06
R07
R08
R09
R10
R11
R12
R13
R14
R15
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
15
14
13
12
11
10
9
DATA47
BR3
PAGE
CLKIN
CS
DATA39
DATA43 DATA45
BR2
BR6
ACK
RD
REDY
DATA36
DATA38 DATA41
DATA46
BR4
DMAG1
WR
DATA34
DATA35 DATA37
DATA40
BR1
BR5
DATA42 DATA44
8
7
6
ADRCLK RCLK0
5
4
3
2
BMS
A
SW
MS0
B
MS1
MS3
C
DMAR2 ADDR30
TCLK0
RCLK1
DT1
DR0
DT0
DR1
HBR
ADDR31
RFS0
TFS0
RFS1
TCLK1
SBTS
ADDR28
DMAG2
HBG
CPA
TFS1
DMAR1
ADDR29
MS2
GND
1
ADDR26 ADDR25
D
GND
ADDR27 ADDR24 ADDR22 ADDR21
E
DATA31 DATA32
DATA30
DATA33
NC
GND
GND
GND
GND
DATA27 DATA28
DATA26
DATA29
GND
GND
VDD
VDD
VDD
GND
GND
ADDR23 ADDR20 ADDR18 ADDR17
F
DATA23 DATA24 DATA25
DATA22
GND
VDD
VDD
VDD
V
DD
VDD
GND
ADDR19
ADDR16 ADDR15 ADDR14
G
DATA20
DATA21
DATA19 DATA18
GND
VDD
VDD
VDD
VDD
VDD
GND
ADDR10 ADDR13 ADDR11 ADDR12
H
DATA17
DATA16
DATA15 DATA12
GND
VDD
VDD
VDD
VDD
VDD
GND
ADDR4
ADDR7
ADDR8
ADDR9
J
DATA14
DATA13
DATA11
DATA8
GND
GND
V
V
V
GND
ICSA
ADDR0
ADDR3
ADDR5
ADDR6
K
DATA10
DATA9
DATA7
DATA4
NC
GND
GND
GND
GND
GND
RPBA
FLAG3
FLAG0
ADDR1
ADDR2
L
DATA6
DATA5
DATA2
L0DAT0
L1DAT1
L2DAT3
L3DAT0
L4DAT2
L5DAT2
L5ACK
LBOOT
TDI
TIMEXP
FLAG2
FLAG1
M
DATA3
DATA1
L0DAT3
L1DAT3
L1ACK
L2DAT0
L3DAT3
L3CLK
L4CLK
L5DAT1
ID2
IRQ1
IRQ0
TDO
EMU
N
DATA0
L0DAT1
L0ACK
L1DAT0
L2DAT2
L2CLK
L3DAT2
L4DAT3
L4DAT0
L5DAT3
L5CLK
ID0
EBOOT
TMS
TRST
P
L0DAT2
L0CLK
L1DAT2
L1CLK
L2DAT1
L2ACK
L3DAT1
L3ACK
L4DAT1
L4ACK
L5DAT0
ID1
RESET
IRQ2
TCK
R
DD
DD
DD
Figure 39. ADSP-21060/ADSP-21062 PBGA Ball Assignments (Top View, Summary)
Rev. H |
Page 53 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
240-LEAD MQFP_PQ4/CQFP PIN CONFIGURATION
Table 41. ADSP-2106x MQFP_PQ4 and ADSP-21060CZ CQFP Pin Assignments (SP-240-2, QS-240-2A, QS-240-2B)
Pin Name
TDI
TRST
VDD
TDO
TIMEXP
EMU
ICSA
FLAG3
FLAG2
FLAG1
FLAG0
GND
ADDR0
ADDR1
VDD
ADDR2
ADDR3
ADDR4
GND
ADDR5
ADDR6
ADDR7
VDD
ADDR8
ADDR9
ADDR10
GND
ADDR11
ADDR12
ADDR13
VDD
ADDR14
ADDR15
GND
ADDR16
ADDR17
ADDR18
VDD
VDD
ADDR19
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Pin Name
ADDR20
ADDR21
GND
ADDR22
ADDR23
ADDR24
VDD
GND
VDD
ADDR25
ADDR26
ADDR27
GND
MS3
MS2
MS1
MS0
SW
BMS
ADDR28
GND
VDD
VDD
ADDR29
ADDR30
ADDR31
GND
SBTS
DMAR2
DMAR1
HBR
DT1
TCLK1
TFS1
DR1
RCLK1
RFS1
GND
CPA
DT0
Pin No.
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
Pin Name
TCLK0
TFS0
DR0
RCLK0
RFS0
VDD
VDD
GND
ADRCLK
REDY
HBG
CS
RD
WR
GND
VDD
GND
CLKIN
ACK
DMAG2
DMAG1
PAGE
VDD
BR6
BR5
BR4
BR3
BR2
BR1
GND
VDD
GND
DATA47
DATA46
DATA45
VDD
DATA44
DATA43
DATA42
GND
Rev. H |
Pin No.
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
Pin Name
DATA41
DATA40
DATA39
VDD
DATA38
DATA37
DATA36
GND
NC
DATA35
DATA34
DATA33
VDD
VDD
GND
DATA32
DATA31
DATA30
GND
DATA29
DATA28
DATA27
VDD
VDD
DATA26
DATA25
DATA24
GND
DATA23
DATA22
DATA21
VDD
DATA20
DATA19
DATA18
GND
DATA17
DATA16
DATA15
VDD
Page 54 of 64 |
March 2013
Pin No.
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
Pin Name
DATA14
DATA13
DATA12
GND
DATA11
DATA10
DATA9
VDD
DATA8
DATA7
DATA6
GND
DATA5
DATA4
DATA3
VDD
DATA2
DATA1
DATA0
GND
GND
L0DAT3
L0DAT2
L0DAT1
L0DAT0
L0CLK
L0ACK
VDD
L1DAT3
L1DAT2
L1DAT1
L1DAT0
L1CLK
L1ACK
GND
GND
VDD
L2DAT3
L2DAT2
L2DAT1
Pin No.
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
Pin Name
L2DAT0
L2CLK
L2ACK
NC
VDD
L3DAT3
L3DAT2
L3DAT1
L3DAT0
L3CLK
L3ACK
GND
L4DAT3
L4DAT2
L4DAT1
L4DAT0
L4CLK
L4ACK
VDD
GND
VDD
L5DAT3
L5DAT2
L5DAT1
L5DAT0
L5CLK
L5ACK
GND
ID2
ID1
ID0
LBOOT
RPBA
RESET
EBOOT
IRQ2
IRQ1
IRQ0
TCK
TMS
Pin No.
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Table 42. ADSP-21060CW/21060LCW CQFP Pin Assignments (QS-240-1A, QS-240-1B)
Pin Name
GND
DATA0
DATA1
DATA2
VDD
DATA3
DATA4
DATA5
GND
DATA6
DATA7
DATA8
VDD
DATA9
DATA10
DATA11
GND
DATA12
DATA13
DATA14
VDD
DATA15
DATA16
DATA17
GND
DATA18
DATA19
DATA20
VDD
DATA21
DATA22
DATA23
GND
DATA24
DATA25
DATA26
VDD
VDD
DATA27
DATA28
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Pin Name
DATA29
GND
DATA30
DATA31
DATA32
GND
VDD
VDD
DATA33
DATA34
DATA35
NC
GND
DATA36
DATA37
DATA38
VDD
DATA39
DATA40
DATA41
GND
DATA42
DATA43
DATA44
VDD
DATA45
DATA46
DATA47
GND
VDD
GND
BR1
BR2
BR3
BR4
BR5
BR6
VDD
PAGE
DMAG1
Pin No.
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
Pin Name
DMAG2
ACK
CLKIN
GND
VDD
GND
WR
RD
CS
HBG
REDY
ADRCLK
GND
VDD
VDD
RFS0
RCLK0
DR0
TFS0
TCLK0
DT0
CPA
GND
RFS1
RCLK1
DR1
TFS1
TCLK1
DT1
HBR
DMAR1
DMAR2
SBTS
GND
ADDR31
ADDR30
ADDR29
VDD
VDD
GND
Rev. H |
Pin No.
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
Pin Name
ADDR28
BMS
SW
MS0
MS1
MS2
MS3
GND
ADDR27
ADDR26
ADDR25
VDD
GND
VDD
ADDR24
ADDR23
ADDR22
GND
ADDR21
ADDR20
ADDR19
VDD
VDD
ADDR18
ADDR17
ADDR16
GND
ADDR15
ADDR14
VDD
ADDR13
ADDR12
ADDR11
GND
ADDR10
ADDR9
ADDR8
VDD
ADDR7
ADDR6
Page 55 of 64 |
March 2013
Pin No.
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
Pin Name
ADDR5
GND
ADDR4
ADDR3
ADDR2
VDD
ADDR1
ADDR0
GND
FLAG0
FLAG1
FLAG2
FLAG3
ICSA
EMU
TIMEXP
TDO
VDD
TRST
TDI
TMS
TCK
IRQ0
IRQ1
IRQ2
EBOOT
RESET
RPBA
LBOOT
ID0
ID1
ID2
GND
L5ACK
L5CLK
L5DAT0
L5DAT1
L5DAT2
L5DAT3
VDD
Pin No.
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
Pin Name
GND
VDD
L4ACK
L4CLK
L4DAT0
L4DAT1
L4DAT2
L4DAT3
GND
L3ACK
L3CLK
L3DAT0
L3DAT1
L3DAT2
L3DAT3
VDD
NC
L2ACK
L2CLK
L2DAT0
L2DAT1
L2DAT2
L2DAT3
VDD
GND
GND
L1ACK
L1CLK
L1DAT0
L1DAT1
L1DAT2
L1DAT3
VDD
L0ACK
L0CLK
L0DAT0
L0DAT1
L0DAT2
L0DAT3
GND
Pin No.
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
OUTLINE DIMENSIONS
23.20
23.00 SQ
22.80
A1 CORNER
INDEX AREA
15 13 11 9
7
5
3
1
14 12 10 8
6
4
2
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
BALL A1
INDICATOR
20.10
20.00 SQ
19.90
TOP VIEW
18.00
BSC SQ
1.27
BSC
0.50 R
3 PLACES
BOTTOM VIEW
DETAIL A
2.70 MAX
DETAIL A
0.70
0.60
0.50
SEATING
PLANE
0.15 MAX
COPLANARITY
0.90
0.75
0.60
BALL DIAMETER
COMPLIANT TO JEDEC STANDARDS MS-034-AAJ-2
Figure 40. 225-Ball Plastic Ball Grid Array [PBGA]
(B-225-2)
Dimensions shown in millimeters
Rev. H |
Page 56 of 64 |
1.30
1.20
1.10
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
34.60 BSC
SQ
0.66
0.56
0.46
29.50 REF
SQ
4.10
3.78
3.55
181
240
1
180
SEATING
PLANE
PIN 1
24.00 REF
SQ
HEAT SLUG
TOP VIEW
(PINS DOWN)
32.00 BSC
SQ
121
60
3.50
3.40
3.30
0.20
0.09
0.38
0.25
7°
0°
VIEW A
0.076
COPLANARITY
120
61
0.50
BSC
LEAD PITCH
3.92 × 45°
(4 PLACES)
0.27 MAX
0.17 MIN
VIEW A
ROTATED 90° CCW
COMPLIANT WITH JEDEC STANDARDS MS-029-GA
Figure 41. 240-Lead Metric Quad Flat Package, Thermally Enhanced “PowerQuad” [MQFP_PQ4]
(SP-240-2)
Dimensions shown in millimeters
Rev. H |
Page 57 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
36.60
36.13 SQ
35.65
28.05
27.80 SQ
27.55
32.00 BSC SQ
PIN 1
INDICATOR
181
240
181
240
1
180
180
1
SEAL RING
LID
TOP VIEW
(PINS DOWN)
BOTTOM VIEW
(PINS UP)
HEAT SLUG
121
60
61
4.30
3.62
2.95
3.70
3.22
2.75
0.90
0.75
0.60
0.23
0.20
0.17
60
120
61
VIEW A
19.00
REF SQ
7°
-3°
121
120
0.50 BSC
0.60
0.40
0.20
1.70
0.15
0.35
0.30
0.25
0.175
0.156
0.137
NOTES:
1. LEAD FINISH = GOLD PLATE
2. LEAD SWEEP/LEAD OFFSET = 0.013mm MAX
(Sweep and/or Offset can be used as the controlling dimension).
0.180
0.155
0.130
LEAD THICKNESS
2.06 REF
VIEW A
Figure 42. 240-Lead Ceramic Quad Flat Package, Heat Slug Up [CQFP]
(QS-240-2A)
Dimensions shown in millimeters
Rev. H |
Page 58 of 64 |
0.15
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
2.60
2.55
2.50
75.00 BSC SQ
29.50 BSC
16.50 (8×)
2.05
3.60
3.55
3.50
120
120
61
61
121
121
60
60
SEAL RING
LID
65.90
BSC
29.50
BSC
TOP VIEW
BOTTOM VIEW
HEAT SLUG
1
1
180
240 INDEX 1
181
INDEX 2
1.50 DIA
NO GOLD
GOLD
PLATED
240
1.22 (4×)
NONCONDUCTIVE
CERAMIC TIE BAR
70.00 BSC SQ
75.50 BSC SQ
0.50
3.42
3.17
2.92
0.90
0.80
0.70
SIDE VIEW
Figure 43. 240-Lead Ceramic Quad Flat Package, Mounted with Cavity Down [CQFP]
(QS-240-2B)
Dimensions shown in millimeters
Rev. H |
Page 59 of 64 |
March 2013
180
181
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
36.60
36.13 SQ
35.65
19.00
REF SQ
32.00 BSC SQ
PIN 1
INDICATOR
181
240
181
240
1
180
180
1
SEAL RING
LID
TOP VIEW
(PINS DOWN)
BOTTOM VIEW
(PINS UP)
HEAT SLUG
121
60
61
28.05
27.80 SQ
27.55
4.20
3.52
2.85
7°
-3°
121
0.90
0.75
0.60
0.23
0.20
0.17
60
120
120
61
VIEW A
3.70
3.22
2.75
0.50 BSC
0.50
0.30
0.10
1.70
0.15
0.35
0.30
0.25
0.175
0.156
0.137
NOTES:
1. LEAD FINISH = GOLD PLATE
2. LEAD SWEEP/LEAD OFFSET = 0.013mm MAX
(Sweep and/or Offset can be used as the controlling dimension).
0.180
0.155
0.130
LEAD THICKNESS
2.06 REF
VIEW A
Figure 44. 240-Lead Ceramic Quad Flat Package, Heat Slug Down [CQFP]
(QS-240-1A)
Dimensions shown in millimeters
Rev. H |
Page 60 of 64 |
0.15
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
2.60
2.55
2.50
75.00 BSC SQ
29.50 BSC
16.50 (8×)
2.05
3.60
3.55
3.50
120
120
61
61
121
121
60
60
SEAL RING
LID
65.90
BSC
29.50
BSC
TOP VIEW
BOTTOM VIEW
HEAT SLUG
240 INDEX 1
181
180
1
1
180
INDEX 2
2.00 DIA
NO GOLD
GOLD
PLATED
240
181
1.22 (4×)
NONCONDUCTIVE
CERAMIC TIE BAR
70.00 BSC SQ
75.50 BSC SQ
0.50
3.42
3.17
2.92
0.90
0.80
0.70
SIDE VIEW
Figure 45. 240-Lead Ceramic Quad Flat Package, Mounted with Cavity Up [CQFP]
(QS-240-1B)
Dimensions shown in millimeters
SURFACE-MOUNT DESIGN
Table 43 is provided as an aide to PCB design. For industrystandard design recommendations, refer to IPC-7351, Generic
Requirements for Surface-Mount Design and Land Pattern
Standard.
Table 43. BGA Data for Use with Surface-Mount Design
Package
225-Ball Grid Array (PBGA)
Ball Attach Type
Solder Mask Defined
Rev. H |
Page 61 of 64 |
Solder Mask Opening
0.63 mm diameter
March 2013
Ball Pad Size
0.76 mm diameter
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
ORDERING GUIDE
Model
ASDP-21060CZ-133
ASDP-21060CZ-160
ASDP-21060CW-133
ASDP-21060CW-160
ADSP-21060KS-133
ADSP-21060KSZ-133
ADSP-21060KS-160
ADSP-21060KSZ-160
ADSP-21060KB-160
ADSP-21060KBZ-160
ADSP-21060LKSZ-133
ADSP-21060LKS-160
ADSP-21060LKSZ-160
ADSP-21060LKB-160
ADSP-21060LAB-160
ADSP-21060LABZ-160
ADSP-21060LCB-133
ADSP-21060LCBZ-133
ASDP-21060LCW-160
ADSP-21062KS-133
ADSP-21062KSZ-133
ADSP-21062KS-160
ADSP-21062KSZ-160
ADSP-21062KB-160
ADSP-21062KBZ-160
ADSP-21062CS-160
ADSP-21062CSZ-160
ADSP-21062LKSZ-133
ADSP-21062LKS-160
ADSP-21062LKSZ-160
ADSP-21062LKB-160
ADSP-21062LKBZ-160
ADSP-21062LAB-160
ADSP-21062LABZ-160
ADSP-21062LCS-160
ADSP-21062LCSZ-160
Temperature
Notes Range
1, 2
–40C to +100C
1, 2
–40C to +100C
1, 2
–40C to +100C
1, 2
–40C to +100C
0C to 85C
2
0C to 85C
0C to 85C
2
0C to 85C
0C to 85C
2
0C to 85C
2
0C to 85C
0C to 85C
2
0C to 85C
0C to 85C
–40C to +85C
2
–40C to +85C
–40C to +100C
2
–40C to +100C
1, 2
–40C to +100C
0C to 85C
2
0C to 85C
0C to 85C
2
0C to 85C
0C to 85C
2
0C to 85C
–40C to +100C
2
–40C to +100C
2
0C to 85C
0C to 85C
2
0C to 85C
0C to 85C
2
0C to 85C
–40C to 85C
2
–40C to 85C
–40C to +100C
2
–40C to +100C
Instruction
Rate
33 MHz
40 MHz
33 MHz
40 MHz
33 MHz
33 MHz
40 MHz
40 MHz
40 MHz
40 MHz
33 MHz
40 MHz
40 MHz
40 MHz
40 MHz
40 MHz
33 MHz
33 MHz
40 MHz
33 MHz
33 MHz
40 MHz
40 MHz
40 MHz
40 MHz
40 MHz
40 MHz
33 MHz
40 MHz
40 MHz
40 MHz
40 MHz
40 MHz
40 MHz
40 MHz
40 MHz
On-Chip
SRAM
4M Bit
4M Bit
4M Bit
4M Bit
4M Bit
4M Bit
4M Bit
4M Bit
4M Bit
4M Bit
4M Bit
4M Bit
4M Bit
4M Bit
4M Bit
4M Bit
4M Bit
4M Bit
4M Bit
2M Bit
2M Bit
2M Bit
2M Bit
2M Bit
2M Bit
2M Bit
2M Bit
2M Bit
2M Bit
2M Bit
2M Bit
2M Bit
2M Bit
2M Bit
2M Bit
2M Bit
Operating
Voltage
5V
5V
5V
5V
5V
5V
5V
5V
5V
5V
3.3 V
3.3 V
3.3 V
3.3 V
3.3 V
3.3 V
3.3 V
3.3 V
3.3 V
5V
5V
5V
5V
5V
5V
5V
5V
3.3 V
3.3 V
3.3 V
3.3 V
3.3 V
3.3 V
3.3 V
3.3 V
3.3 V
1
Package Description
240-Lead CQFP [Heat Slug Up]
240-Lead CQFP [Heat Slug Up]
240-Lead CQFP [Heat Slug Down]
240-Lead CQFP [Heat Slug Down]
240-Lead MQFP_PQ4
240-Lead MQFP_PQ4
240-Lead MQFP_PQ4
240-Lead MQFP_PQ4
225-Ball PBGA
225-Ball PBGA
240-Lead MQFP_PQ4
240-Lead MQFP_PQ4
240-Lead MQFP_PQ4
225-Ball PBGA
225-Ball PBGA
225-Ball PBGA
225-Ball PBGA
225-Ball PBGA
240-Lead CQFP [Heat Slug Down]
240-Lead MQFP_PQ4
240-Lead MQFP_PQ4
240-Lead MQFP_PQ4
240-Lead MQFP_PQ4
225-Ball PBGA
225-Ball PBGA
240-Lead MQFP_PQ4
240-Lead MQFP_PQ4
240-Lead MQFP_PQ4
240-Lead MQFP_PQ4
240-Lead MQFP_PQ4
225-Ball PBGA
225-Ball PBGA
225-Ball PBGA
225-Ball PBGA
240-Lead MQFP_PQ4
240-Lead MQFP_PQ4
Package
Option
QS-240-2A
QS-240-2A
QS-240-1A
QS-240-1A
SP-240-2
SP-240-2
SP-240-2
SP-240-2
B-225-2
B-225-2
SP-240-2
SP-240-2
SP-240-2
B-225-2
B-225-2
B-225-2
B-225-2
B-225-2
QS-240-1A
SP-240-2
SP-240-2
SP-240-2
SP-240-2
B-225-2
B-225-2
SP-240-2
SP-240-2
SP-240-2
SP-240-2
SP-240-2
B-225-2
B-225-2
B-225-2
B-225-2
SP-240-2
SP-240-2
Model refers to package with formed leads. For model numbers of unformed lead versions (QS-240-1B, QS-240-2B), contact Analog Devices or an Analog Devices sales
representative.
2
RoHS compliant part.
Rev. H |
Page 62 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Rev. H |
Page 63 of 64 |
March 2013
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
©2013 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D00167-0-3/13(H)
Rev. H |
Page 64 of 64 |
March 2013