EVAL-AD2S1210SDZ

EVAL-AD2S1210SDZ User Guide UG-709 One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com Evaluating the AD2S1210 10-Bit to16-Bit Resolver-to-Digital Converter FEATURES GENERAL DESCRIPTION Full featured evaluation board for the AD2S1210 On-board power supplies Standalone capability System demonstration platform (SDP) compatible (EVAL-SDP-CB1Z) PC software for control and data analysis The EVAL-AD2S1210SDZ is a full featured evaluation board designed to allow the user to easily evaluate all the features of the AD2S1210 resolver-to-digital converter (RDC). The evaluation board can be controlled via the SDP connector (J2) or via the J3 and J4 connectors. The SDP board (EVAL-SDP-CB1Z) allows the evaluation board to be controlled through the USB port of a PC using the evaluation board software available for download from the AD2S1210 product page. EVALUATION KIT CONTENTS EVAL-AD2S1210SDZ evaluation board Mains power supply adapter Evaluation software CD The EVAL-AD2S1210SDZ on-board components include:    ADDITIONAL EQUIPMENT NEEDED EVAL-SDP-CB1Z (must be ordered separately), includes a USB cable Resolver PC running Windows 7 or later, with CD-ROM drive and USB 2.0 port  The AD8662 low noise, precision 16 V rail-to-rail op amp The AD8397 high current, precision rail-to-rail op amp The ADP1621 constant frequency, current-mode step-up dc-to-dc converter The ADP3303 200 mA low dropout linear regulator TYPICAL EVALUATION SETUP WALL OUTLET 100V AC TO 240V AC 47Hz TO 63Hz SWITCHING POWER SUPPLY TO RESOLVER PC RUNNING EVALUATION BOARD SOFTWARE Figure 1. Typical Setup Using the EVAL-AD2S1210SDZ (Left) and the EVAL-SDP-CB1Z (Right) PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | Page 1 of 16 12385-001 FROM RESOLVER UG-709 EVAL-AD2S1210SDZ User Guide TABLE OF CONTENTS Features .............................................................................................. 1 Power Supplies ...............................................................................7 Evaluation Kit Contents ................................................................... 1 Link Configuration Options ............................................................8 Additional Equipment Needed ....................................................... 1 Setup Conditions ...........................................................................8 General Description ......................................................................... 1 Evaluation Board Circuitry ........................................................... 10 Typical Evaluation Setup ................................................................. 1 Sockets/Connectors ................................................................... 10 Revision History ............................................................................... 2 Test Points ................................................................................... 10 Getting Started .................................................................................. 3 Launching the Evaluation Software ......................................... 11 Quick Start Steps .......................................................................... 3 Description of Main Window ................................................... 12 Software Installation Procedures ................................................ 4 Acquisition .................................................................................. 13 Evaluation Board Setup Procedures........................................... 6 Position/Velocity—Histogram ................................................. 14 Evaluation Board Hardware ............................................................ 7 Saving Files .................................................................................. 15 AD2S1210 Description ................................................................ 7 Opening Files .............................................................................. 16 Hardware Link Options ............................................................... 7 REVISION HISTORY 10/14—Revision 0: Initial Version Rev. 0 | Page 2 of 16 EVAL-AD2S1210SDZ User Guide UG-709 GETTING STARTED 3. QUICK START STEPS Follow these steps to quickly evaluate the AD2S1210 RDC: 2. Install the evaluation software supplied on the included evaluation software CD. Ensure that the EVAL-SDP-CB1Z board is disconnected from the USB port of the PC while installing the software. The PC may need to be restarted after the installation. Ensure that the various link options are configured as shown in Table 2. 4. 5. 6. 7. 12385-002 1. Connect the EVAL-SDP-CB1Z board to the EVALAD2S1210SDZ evaluation board, as shown in Figure 2. Connect the 9 V power supply adapter included in the kit to Connecter J702 on the evaluation board. Connect the EVAL-SDP-CB1Z board to the PC via the USB cable. Launch the evaluation software from the Analog Devices subfolder in the Programs menu. Connect the EXC, EXC, SIN, SIN, COS, and COS wires of the resolver to Connector J5 and Connector J6, as shown in Figure 1. Figure 2. Evaluation Board (Left) Connected to the SDP Board (Right) Rev. 0 | Page 3 of 16 UG-709 EVAL-AD2S1210SDZ User Guide SOFTWARE INSTALLATION PROCEDURES The EVAL-AD2S1210SDZ kit includes a CD containing software to be installed on your PC before using the evaluation board. 5. A license agreement appears. Read the agreement, select I accept the License Agreement, and click Next. There are two parts to the installation:   EVAL-AD2S1210SDZ evaluation software installation EVAL-SDP-CB1Z driver installation Warning The evaluation board software and drivers must be installed before connecting the evaluation board and the SDP board to the USB port of the PC to ensure that the evaluation system is correctly recognized when it is connected to the PC. Installing the Evaluation Board Software To install the EVAL-AD2S1210SDZ evaluation board software, take the following steps: 1. 2. 3. Insert the included evaluation software installation CD into the CD drive of a Windows®-based PC, and open the contents of the CD. Double-click the setup.exe file to begin the installation. By default, the software is saved to the following location: C:\Program Files\Analog Devices\AD2S1210\. A dialog box appears asking for permission to allow the program to make changes to your computer. Click Yes to begin the installation process. Figure 5. Evaluation Software Installation—License Agreement 6. An installation summary appears. Click Next to continue. Figure 6. Evaluation Software Installation—Start Installation 7. Figure 3. Evaluation Software Installation—User Account Control 4. Select the location to install the software, and then click Next. Figure 4. Evaluation Software Installation—Destination Directory A dialog box informs you when the evaluation software installation is complete. Click Next to proceed with the installation of the drivers. Figure 7. Evaluation Software Installation—Installation Complete Rev. 0 | Page 4 of 16 EVAL-AD2S1210SDZ User Guide UG-709 Installing the System Demonstration Platform Board Drivers 3. Click Install to proceed with the installation. After the installation of the evaluation board software is complete, the ADI SDP Drivers Setup wizard window opens for the installation of the EVAL-SDP-CB1Z system demonstration platform board drivers. 1. Make sure that all other applications are closed, and then click Next to begin the driver installation process. Figure 10. EVAL-SDP-CB1Z Drivers Installation—Windows Security 4. To complete the drivers installation, click Finish, which closes the installation wizard. Figure 8. EVAL-SDP-CB1Z Drivers Installation—Setup Wizard 2. Select the location to install the drivers, and then click Install. Figure 11. EVAL-SDP-CB1Z Drivers Installation—Complete Figure 9. EVAL-SDP-CB1Z Drivers Installation—Choose Install Location Rev. 0 | Page 5 of 16 UG-709 EVAL-AD2S1210SDZ User Guide EVALUATION BOARD SETUP PROCEDURES The EVAL-AD2S1210SDZ connects to the EVAL-SDP-CB1Z system demonstration platform. The EVAL-SDP-CB1Z board is the controller board, which provides the communication link between the PC and the main evaluation board. Before connecting the EVAL-SDP-CB1Z board to the PC, ensure that the evaluation software has been installed. The full software installation procedure is detailed in the Software Installation Procedures section. Figure 2 shows a photograph of the connections between the EVAL-AD2S1210SDZ daughter board and the EVAL-SDP-CB1Z board. Finally, connect the EVAL-SDP-CB1Z board to the PC via the USB cable enclosed in the EVAL-SDP-CB1Z kit. To evaluate the AD2S1210, an external resolver must be connected to the EVAL-AD2S1210SDZ. Connect EXE and EXC signal wires from the resolver to the J6 screw terminal. Connect the SIN, SIN, COS, and COS resolver wires to the J5 screw terminal. 1. Verifying the Board Connection There are two excitation driver options provided on the EVALAD2S1210SDZ. Use Link 14 to Link 17 to select the desired driver (see Table 2). The default excitation driver combines an AD8662 precision, rail-to-rail, dual op-amp with a push-pull transistor network. An alternative driver available employs the AD8397 high current, precision rail-to-rail op-amp to drive the excitation signals. In both driver options, a dc bias of 3.75 V is applied to the EXE and EXC signals. Link 10 to Link 13 are used to adjust the excitation gain for each of the drivers (see Table 2). Before connecting the power supply, connect the EVALAD2S1210SDZ evaluation board to Connector A or Connector B on the EVAL-SDP-CB1Z board. A nylon screw/nut set is included in the evaluation kit and can be used to ensure that the evaluation board and the EVAL-SDP-CB1Z board are connected firmly together. After the evaluation board and the EVAL-SDP-CB1Z board are connected securely, connect the power supply to the evaluation board. The EVAL-AD2S1210SDZ evaluation board requires an external 9 V power supply adapter, which is included in the evaluation board kit. Connect this power supply to Connector J702 on the evaluation board. For further details on the required power supply connections and options, see the Power Supplies section. Rev. 0 | Page 6 of 16 Allow the Found New Hardware Wizard to run after the EVAL-SDP-CB1Z board is plugged into your PC. Check that the board is connected to the PC correctly using the Device Manager of the PC. a. Access the Device Manager as follows: i. Right-click My Computer and then click Manage. ii. A dialog box appears asking for permission to allow the program to make changes to your computer. Click Yes. iii. The Computer Management box appears. From the list of System Tools, click Device Manager. b. Under ADI Development Tools, Analog Devices System Development Platform SDP-B appears (see Figure 12), indicating that the EVAL-SDP-CB1Z driver software is installed and that the board is connected to the PC correctly. Figure 12. Device Manager EVAL-AD2S1210SDZ User Guide UG-709 EVALUATION BOARD HARDWARE 50 Hz to 60 Hz. The output from the supply is provided through a 2.0 mm inner diameter jack that connects to the evaluation board at J702. When supplied via J702, the evaluation board uses the ADP1621 and the ADP3303 to supply the various rails on the board. AD2S1210 DESCRIPTION The AD2S1210 is a complete 10-bit to 16-bit, resolution tracking RDC, integrating an on-board programmable sinusoidal oscillator that provides sine wave excitation for resolvers. The converter accepts 3.15 V p-p ± 27% input signals, in the range of 2 kHz to 20 kHz on the sine and cosine inputs. A Type II servo loop is employed to track the inputs and converts the input sine and cosine information into a digital representation of the input angle and velocity. The maximum tracking rate is 3125 RPS. If the evaluation board is used without the 9 V adapter, an external power supply in the range of 4.75 V to 5.25 V must be connected to the DVDD and AVDD connectors to supply the AD2S1210 DVDD and AVDD pins. In addition, an external 12 V supply must be connected to the 12 V input to supply the excitation drivers. VDRIVE is by default supplied from the DVDD connector. Optionally, VDRIVE can be supplied by connecting an external supply in the range of 2.3 V to 5.25 V to the VDRIVE input. Consult Table 2 and Table 3 when externally supplying the EVAL-AD2S1210SDZ. Complete specifications for the AD2S1210 are available in the AD2S1210 data sheet, which should be consulted in conjunction with this user guide when using the evaluation board. Full details on the EVAL-SDP-CB1Z are available at the SDP board product page. There are two main ground planes, AGND and DGND. These ground planes are connected at one location close to the RDC. AVDD and DVDD are both decoupled using 10 μF tantalum and 10 nF multilayer ceramic capacitors. HARDWARE LINK OPTIONS The functions of the link options are described in Table 2. The default setup is configured to operate the EVAL-AD2S1210SDZ evaluation board with the mains power supply adapter and to interface to the EVAL-SDP-CB1Z board. Table 1. External Power Supplies POWER SUPPLIES Before applying power and signals to the evaluation board, ensure that all link positions are set according to the required operating mode. See Table 2 for the complete list of link options. The EVAL-AD2S1210SDZ evaluation board is supplied with a wall-mountable switching power supply that provides a 9 V dc output. Connect the supply to a 100 V to 240 V ac wall outlet at Power Supply DC Jack Voltage Range 9 V ± 5% DVDD AVDD VDRIVE 12 V 4.75 V to 5.25 V 4.75 V to 5.25 V 2.3 V to 5.25 V 12 V ± 5% Purpose Supplies power to on-board power management devices AD2S1210 digital supply rail AD2S1210 analog supply rail Digital interface supply rail Excitation driver supply VDRIVE GND AVDD GND DVDD GND DC JACK ON-BOARD POWER SUPPLY EXC EXC SIN SINLO COS COSLO B A B A EXC EXC VDRIVE AVDD SIN DVDD DATA BUS DB0 TO DB15 AD2S1210 SINLO COS COSLO CS RD SAMPLE WR/FSYNC ADSP-BF527 DSP SDP-B BOARD DB0 TO DB15 A, B, NM, DIR DOS, LOT SAMPLE, WR/FSYNC, SCLK,SDI, SDO, A0, A1 26-WAY CONNECTOR 12-WAY CONNECTOR Figure 13. EVAL-AD2S1210SDZ Functional Block Diagram Rev. 0 | Page 7 of 16 12385-013 B A UG-709 EVAL-AD2S1210SDZ User Guide LINK CONFIGURATION OPTIONS Multiple link options must be set correctly to select the appropriate operating setup before using the evaluation board. The functions of these options are described in Table 2. evaluation board. The evaluation board can be operated in SDP-B controlled mode to be used with the EVAL-SDP-CB1Z board, or the evaluation board can be used in standalone mode. SETUP CONDITIONS Table 2 shows the default positions in which the links are set when the evaluation board is packaged. When the board is shipped, it is set up to operate in SDP-B controlled mode, with the power supplied from the included 9 V dc switching power supply. Before applying power and signals to the evaluation board, ensure that all link positions are configured as required by the operating mode. There are two modes in which to operate the Table 2. Link Options Link LK701 Default Position A LK702 A LK703 A LK501 A Excitation Driver Selection LK14 to LK17 A Excitation Driver Gain LK10 to LK13 B AD2S1210 Configuration Pins LK4 C LK5 C LK6 C LK7 C LK9 A Category Power Supplies Function This link is used to select the source of the AVDD supply for the AD2S1210. In Position A, AVDD is supplied via the on-board ADP3303 linear regulator. In Position B, AVDD is supplied via Connector J703. This link is used to select source of the DVDD supply for the AD2S1210. In Position A, DVDD is supplied via the on-board ADP3303 linear regulator. In Position B, DVDD is supplied via Connector J701. This link is used to select the source of the VDRIVE supply for the AD2S1210. In Position A, VDRIVE is tied to DVDD. In Position B, the VDRIVE is supplied externally via Connector J704. This link is used to select the source of the 12 V supply for the excitation drivers. In Position A, 12 V is supplied via the on-board ADP1621 dc-to-dc converter. In Position B, 12 V must be supplied externally via Connector J500. These links select the excitation drivers used. In Position A, the AD8662 in conjunction with a push-pull driver circuit is used. In Position B, the high current AD8397 op amp is used. LK14 to LK17 must be placed in the same position. These links select the gain applied to the EXC and EXC signals. In Position A, the user can set the gain. Gain = R/10 kΩ, where R = R1 = R4. In Position B, a gain of 1.54 is applied. In Position C, a gain of 0.866 is applied. A0: In Position A, A0 is tied to VDRIVE. In Position B, A0 is tied to DGND. In Position C, A0 is controlled via J2 or J4 A1: In Position A, A1 is tied to VDRIVE. In Position B, A1 is tied to DGND. In Position C, A1 is controlled via J2 or J4. RES0: In Position A, RES0 is tied to VDRIVE. In Position B, RES0 is tied to DGND. In Position C, RES0 is controlled via J2. RES1: In Position A, RES1 is tied to VDRIVE. In Position B, RES1 is tied to DGND. In Position C, RES1 is controlled via J2. SOE: In Position A, SOE is tied to VDRIVE In Position B, SOE is tied to DGND Rev. 0 | Page 8 of 16 EVAL-AD2S1210SDZ User Guide Category Digital Interface Options Link LK2 Default Position C UG-709 Function CS source: In Position A, CS is controlled via tact switch S2. In Position B, CS is tied to DGND. In Position C, CS is controlled via J2 or J4. LK3 C RD source: In Position A, RD is tied to CS. In Position B, RD is tied to VDRIVE. In Position C, RD is controlled via J2 or J4. L1 B SAMPLE source: In Position A, SAMPLE is controlled via tact switch S2. In Position B, SAMPLE is controlled via J2 or J4. Rev. 0 | Page 9 of 16 UG-709 EVAL-AD2S1210SDZ User Guide EVALUATION BOARD CIRCUITRY SOCKETS/CONNECTORS TEST POINTS The connectors and sockets on the EVAL-AD2S1210SDZ are described in Table 3. There are numerous test points on the EVAL-AD2S1210SDZ board. These test points provide easy access to the signals from the evaluation board for probing, evaluation, and debugging. The default interface to this evaluation board is via the 120-way Connector J2, which connects theAD2S1210 to the EVAL-SDPCB1Z board. Table 3. On-Board Connectors Connector J2 J3 J4 J5 J6 J500 J701 J702 J703 J704 Function EVAL-SDP-CB1Z connector Parallel interface Serial interface Resolver input to AD2S1210 Excitation signal output External 12 V supply External DVDD supply 9 V dc barrel socket External AVDD supply External VDRIVE supply Rev. 0 | Page 10 of 16 EVAL-AD2S1210SDZ User Guide UG-709 LAUNCHING THE EVALUATION SOFTWARE After the evaluation board and the EVAL-SDP-CB1Z board are correctly connected to the PC, the evaluation software can be launched. From the Start menu, go to Programs > Analog Devices > AD2S1210. The main window of the software then opens (see Figure 15). If the evaluation board is not connected to the USB port via the EVAL-SDP-CB1Z when the software is launched, a connectivity error displays (see Figure 14). Connect the evaluation board to the USB port of the PC, wait a few seconds, click Rescan, and follow the instructions that appear. Figure 14. Connectivity Error Alert 1 4 6 3 12385-015 2 5 Figure 15. Evaluation Software Main Window Rev. 0 | Page 11 of 16 UG-709 EVAL-AD2S1210SDZ User Guide DESCRIPTION OF MAIN WINDOW Control Buttons, Drop-Down Boxes, and Indicators When the software is launched, the main software window opens (see Figure 15). The evaluation software includes the following control buttons, drop-down boxes, and indicators. The main software window shown in Figure 15 has the following features:        Menu bar Control buttons Configuration display Data capture display (position and velocity) Fault register display Menu Bar The menu bar, Label 1 in Figure 15, consists of the File, Edit, Graph Options, and Help menus. File Menu        Save Data. Saves captured data in comma separated values (CSV) format for future analysis. Save Register Configuration. Saves the current device configuration as an XML file for later use. Load Data. Loads previously captured data in CSV format for analysis. Save Register Configuration. Loads a previously saved AD2S1210 register configuration. Save Screenshot. Saves a screenshot of the current window as a JPEG file. Exit. Exits the program.  #Samples. Label 4. Selects the number of samples to be obtained in a single acquisition. Read Mode. Label 5. Selects between the two read modes: o Continuous Acquisition. Repeatedly acquires data from the part one sample at a time. This mode has no fixed sampling rate and streams data from the part as fast as the software will allow. o Single Acquisition. Captures a defined sample set with the number of samples per acquisition defined in the #Samples control, then transfers the data back to the software for display and analysis. This mode has a fixed sampling rate of 500 kHz. Read. Label 6. Initiates acquisition from the RDC. Click a second time to stop data acquisition when in Continuous Acquisition mode. Fault. Label 3. Displays the status of the fault register. The LED is active when fault bits are set in the fault register. Configuration Buttons There are three configuration register buttons contained within the block diagram under the Configuration tab. Clicking the blue button (see Figure 16) produces a pop-up box that allow the user to configure the respective section of the block diagram. Figure 16. Configuration Register Button Edit Menu The three buttons control the Excitation Outputs (Reference Oscillator (DAC)), the Configuration Registers, and the Fault Detection. Refer to the AD2S1210 data sheet for details on available configuration options. Reinitialize to default. Places the evaluation board and software in a known default state. Graph Options    Data Capture Display AutoScale X. Toggles AutoScale on the x-axis. AutoScale Y. Toggles AutoScale on the y-axis. Clear Graphs/Data. Clears all graphs and numeric indicators. There are four tabs (Label 2) to choose from in the software: Configuration, Acquisition, Position Histogram, and Position Histogram. See Label 2 in Figure 15. Help Menu    Context Help. Turns on context sensitive help. User Guide. Opens the evaluation kit webpage with a link to the evaluation board user guide. About. Provides evaluation software version information. The tools shown in Figure 17 allow user control of the different chart displays within the Acquisition, Position Histogram, and Position Histogram tabs. 1 2 3 1. USED FOR CONTROLLING THE CURSOR, IF PRESENT. 2. USED FOR ZOOMING IN AND OUT. 3. USED FOR PANNING. Figure 17. Chart Tools Rev. 0 | Page 12 of 16 12385-017  EVAL-AD2S1210SDZ User Guide UG-709 Figure 18 illustrates the tab used for Acquisition. The units pertaining to these statistics are specified in the Units drop-down box. The two charts under this tab show the position and velocity data acquired from the AD2S1210. The units for these charts are selected using the Units drop-down box (Label 1 in Figure 18). Two options for units are available: Decimal and Deg/RPS. The Fault Register indicator (Label 3) provides a detailed view of the AD2S1210 fault register status. Clicking the Clear Fault Register button (Label 4) runs through a sequence to clear the AD2S1210 fault register. Indicators on the rights of this tab (Label 2) provide statistics on the acquired data, including maximum, minimum, and mean. The fault register is read during software initialization, after each acquisition, and after clearing the fault register. ACQUISITION 1 2 3 12385-018 4 Figure 18. Acquisition Tab Rev. 0 | Page 13 of 16 UG-709 EVAL-AD2S1210SDZ User Guide POSITION/VELOCITY—HISTOGRAM Figure 19 shows the Position Histogram tab. The Velocity Histogram tab follows the same format. The graph shown in each of these tabs displays a histogram of the position or velocity data acquired. Below the graph are three indicators (Label 1) providing statistics on the acquired data. 12385-019 1 Figure 19. Position Histogram Tab Rev. 0 | Page 14 of 16 EVAL-AD2S1210SDZ User Guide UG-709 SAVING FILES Saving Device Configurations The evaluation software can save the current captured data for future analysis. The software can save the current device configuration, the position and velocity data, and a screenshot of the current window To save the current device configuration in XML format, go to the File menu, click Save, and then click Save Register Configuration. The Save As dialog box in Figure 22 opens, prompting for a location to save the XML file. Saving Data 12385-022 To save data, go to the File menu, click Save, and click Save Data. This option saves both the position and velocity data captured (as seen in the Acquisition tab) to a CSV file. When Save Data is clicked, the Save As dialog box in Figure 20 opens, prompting for a location to save the CSV file. 12385-020 Figure 22. Save Register Configuration Dialog Box Figure 20. Save File Dialog Box Saving Screenshots To save a screenshot of the current window, go to the File menu and click Save Screenshot. The Save As dialog box in Figure 21 opens, prompting for a location to save the JPEG file. 12385-021 The images are saved in JPEG format and do not contain any raw data information. Figure 21. Save Image Dialog Box Rev. 0 | Page 15 of 16 UG-709 EVAL-AD2S1210SDZ User Guide Loading Device Configurations Loading Captured Data The software can load a previously used device configuration. The software can load previously captured data for analysis. Go to the File menu, click Load, and click Load Data. The waveform data is a raw data capture that rebuilds the histogram analysis upon being loaded into the evaluation platform. Go to the File menu, click Load, and click Load Register Configuration. The software loads all previously used device settings to the RDC and updates the evaluation platform appropriately. When Load Data is clicked, the open dialog box in Figure 23 appears for loading an appropriate CSV file. When Load Register Configuration is clicked, the Open dialog box in Figure 24 appears for loading an appropriate XML file. 12385-023 12385-024 OPENING FILES Figure 24. Open Configuration Dialog Box Figure 23. Open File Dialog Box ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed. ©2014 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG12385-0-10/14(0) Rev. 0 | Page 16 of 16