Evaluation Board User Guide
UG-079
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluation Board for the AD7781 20-Bit, Pin-Programmable,
Low Power, Sigma-Delta ADC
an on-chip digital filter. The analog input channel of the
AD7781 accepts analog input signals of ±VREF or ±VREF/128.
With the update rate programmed to 10 Hz, the rms noise
is 44 nV when the gain is 128. Simultaneous 50 Hz/60 Hz
rejection is available at both output data rates.
FEATURES
Full-featured evaluation board for the AD7781
Standalone USB interface
Various linking options
PC software for control of AD7781
Full data on the AD7781 is available in the AD7781 data sheet
available from Analog Devices, Inc., and should be consulted in
conjunction with this user guide when using the evaluation board.
GENERAL DESCRIPTION
This user guide describes the evaluation board for the AD7781,
which is a pin programmable, low power, 20-bit sigma-delta
(Σ-Δ) ADC. The AD7781 is a complete analog front end for
low frequency measurement applications such as bridge sensor
systems. It contains one differential input and includes a low
noise instrumentation amplifier. The output data rate can be
programmed to 10 Hz or 16.7 Hz. The AD7781 also has an
on-board clock, eliminating the need for an external clock. It
employs a Σ-Δ conversion technique to realize up to 20 bits
of no missing codes performance. The input signal is applied
to an analog modulator. The modulator output is processed by
The evaluation board interfaces to the USB port of an IBMcompatible PC. Software is available with the evaluation board
that allows users to easily communicate with the AD7781.
Note that the AD7781 evaluation board software should be
installed before connecting the AD7781 evaluation board
to the PC.
Another component on the AD7781 evaluation board is the
ADP3303 high precision, low power, 3.3 V output voltage
regulator, which is used to power the USB/SPI interface.
FUNCTIONAL BLOCK DIAGRAM
AVDD
VOLTAGE
REGULATOR
ANALOG
INPUTS
AD7781
SPI/USB
INTERFACE
USB
CONNECTOR
Figure 1.
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. 0 | Page 1 of 16
PC AND
LabVIEW™
BASED
SOFTWARE
08749-001
LOADCELL
CONNECTOR
UG-079
Evaluation Board User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1
Evaluation Board Software ...............................................................6
General Description ......................................................................... 1
Software Description ....................................................................6
Functional Block Diagram .............................................................. 1
Installing the Software ..................................................................6
Revision History ............................................................................... 2
Using the Software ........................................................................6
Evaluation Board Hardware ............................................................ 3
Main Window ................................................................................7
Power Supplies .............................................................................. 3
Weighscale Demo Window ..........................................................8
Links ............................................................................................... 3
Evaluation Board Schematic and Artwork.....................................9
Setup Conditions .......................................................................... 4
Ordering Information .................................................................... 13
Sockets ........................................................................................... 4
Bill of Materials ........................................................................... 13
Interfacing to the Evaluation Board ........................................... 5
REVISION HISTORY
2/10—Revision 0: Initial Version
Rev. 0 | Page 2 of 16
Evaluation Board User Guide
UG-079
EVALUATION BOARD HARDWARE
POWER SUPPLIES
LINKS
The AD7781 evaluation board is powered via the 5 V supply
from the USB connector, J1. This 5 V supply can be used to
power the AD7781 directly. A 3.3 V regulated voltage from the
on-board ADP3303 (a high precision, low power, 3.3 V output
voltage regulator) can also be used. Alternatively, the AD7781 can
be powered using an external 3 V or 5 V power supply via J2.
There are sixteen groups of link options that must be set for the
required operating setup before using the evaluation board. The
functions of these link options are outlined in Table 1.
Table 1. Evaluation Board Link Settings
Link
LK1, LK2
Default
In
LK3, LK4
In
LK5
3.3 V
LK6 to LK11
In
LK12, LK13, LK14
In
LK15
10 Hz
LK16
128
Description
These links are used to connect the AIN(+) and AIN(−) inputs to AVDD/2. With this configuration, a noise
analysis can be performed. With these links removed, an external voltage may be applied to AIN(+)/AIN(−)
using the SMB connectors.
With LK3 and LK4 in place, AVDD is used as the reference to the AD7781. REFIN(+) is connected to AVDD and
REFIN(−) is connected to GND. To use another reference source, remove LK3 and LK4.
LK5 is used to select the power source for AVDD on the AD7781.
In Position A, LK5 selects an external power supply, supplied via J2.
In Position B, LK5 selects the 3.3 V regulated output from the on-board ADP3303 voltage regulator.
In Position C, LK5 selects the 5 V supply from the USB connector, J1.
These links connect the serial interface pins of the AD7781 to the SPI interface of the microcontroller. The
links should be in place to use the AD7781 evaluation board software. With these links removed, the AD7781
can be interfaced to an external microcontroller.
These links are used for the bridge power-down switch. With LK12 inserted, the bridge power-down switch is
connected to AVDD through an LED. When the bridge power-down switch is closed, the LED turns on. LK13
should be open when LK12 is inserted.
LK13 and LK14 are used when a load cell is connected to Header J4. LK12 should be left open. With LK13
inserted, the bridge power-down switch is connected to Header J4. The low side of the load cell can be
connected to GND through the bridge power-down switch. With LK14 inserted, the low side of the load cell is
connected directly to GND. The terminal REFIN(−) should be shorted to the GND/PSW terminal on Header J4
to enable the previous functions.
LK15 is used to select the output data rate for the AD7781. With LK15 in Position 10 Hz, the output data rate is
set to 10 Hz. When LK15 is in Position 16.7 Hz, the output data rate is set to 16.7 Hz.
LK16 is used to select the gain of the AD7781. With LK16 in Position 1, the gain is set to 1. With LK16 in
Position 128, the gain of the AD7781 is set to 128.
Rev. 0 | Page 3 of 16
UG-079
Evaluation Board User Guide
SETUP CONDITIONS
SOCKETS
Take care before applying power and signals to the evaluation
board to ensure that all link positions are set per the required
operating mode. Table 2 shows the position in which all the
links are initially set.
There are five sockets relevant to the operation of the AD7781
on this evaluation board. The functions of these sockets are
outlined in Table 3.
Table 2. Initial Links and Positions
Link No.
LK1, LK2
LK3, LK4
LK5
LK6 to LK11
LK12
LK13
LK14
Position
In
In
B
In
In
Out
In
Function
AIN(+) and AIN(−) are shorted to AVDD/2.
The reference voltage is set to 3.3 V (AVDD).
The 3.3 V supply is used as AVDD for the AD7781.
The AD7781 is interfaced to the on-board microcontroller.
The bridge power-down switch is connected to AVDD.
The bridge power-down switch is disconnected from Header J4.
Terminal GND/PSW of Header J4 is connected to GND.
Table 3. Socket Functions
Socket
AIN+
AIN−
REFIN+
REFIN−
J4
Description
Subminiature BNC (SMB) connector. The analog input signal for the AIN(+) input of the AD7781 is applied to this socket.
Subminiature BNC (SMB) connector. The analog input signal for the AIN(−) input of the AD7781 is applied to this socket.
Subminiature BNC (SMB) connector. This socket is used in conjunction with REFIN− to apply an external reference to the AD7781.
The voltage for the REFIN(+) input of the AD7781 is applied to this socket.
Subminiature BNC (SMB) connector. This socket is used in conjunction with REFIN+ to apply an external reference to the AD7781.
The voltage for the REFIN(−) input of the AD7781 is applied to this socket.
6-pin terminal block. This is used to connect an external load cell to the AD7781 evaluation board.
Rev. 0 | Page 4 of 16
Evaluation Board User Guide
UG-079
INTERFACING TO THE EVALUATION BOARD
To set up the USB/SPI interface, use the following procedure:
Interface to the evaluation board is via a standard USB
connector, J1. J1 is used to connect the evaluation board
to the USB port of a PC. A standard USB connector cable
is included with the AD7781 evaluation board to allow the
evaluation board to interface with the USB port of the PC.
Because the board is powered via the USB connector, there
is no need for an external power supply, although if preferred,
one may be connected via J2.
1.
3.
08749-002
Communication between the AD7781 and the PC is via the
USB/SPI interface. The on-board USB controller (U2) handles
this communication.
2.
Install the AD7781 evaluation board software using the
supplied AD7781 evaluation board CD before connecting
the board to the PC.
After the AD7781 evaluation board software is installed,
connect the board to the PC via J1 on the AD7781 evaluation
board and via the USB port on the PC using the supplied
USB connector cable. The PC automatically finds the new
USB device and identifies it as the AD779x Evaluation Board.
Follow the on-screen instructions that appear. During the
installation process if the Hardware Installation Wizard
appears as shown in Figure 2, click Continue Anyway
to successfully complete the installation of the AD7781
evaluation board.
Figure 2. Hardware Installation Window
Rev. 0 | Page 5 of 16
UG-079
Evaluation Board User Guide
EVALUATION BOARD SOFTWARE
3.
SOFTWARE DESCRIPTION
The AD7781 evaluation board is shipped with a CD containing
software that can be installed onto a standard PC to control the
AD7781. The software communicates with the AD7781 through
the USB cable, which accompanies the board. The software allows
you to read conversion data from the AD7781. Data can be read
from the AD7781 and displayed or stored for later analysis. For
further information, see the AD7781 data sheet available from
Analog Devices.
4.
At the prompt, select a destination directory, which is
C:\Program Files\Analog Devices\AD7781 by default.
Once the directory is selected, the installation procedure
copies the files into the relevant directories on the hard
drive. The installation program creates a program group
called Analog Devices with the subgroup AD7781 in the
Start menu of the taskbar.
Once the installation procedure is complete, double-click
on the AD7781 icon to start the program.
INSTALLING THE SOFTWARE
USING THE SOFTWARE
Use the following steps to install the software:
Figure 3 shows the main window that is displayed when the
program starts. The Main Window section briefly describes
the various menu and button options in the main window.
Start Windows® and insert the CD.
The installation software should launch automatically. If it
does not, use Windows Explorer to locate the setup.exe file
on the CD. Double-click this file to start the installation
procedure.
The data that has been read can be exported to other packages,
such as MathCAD™ or Microsoft® Excel, for further analysis.
08749-003
1.
2.
Figure 3. AD7781 Evaluation Software Main Window
Rev. 0 | Page 6 of 16
Evaluation Board User Guide
UG-079
MAIN WINDOW
Weighscale Demo
Menu Bar
File
This button allows you to access the weighscale demonstration
software.
The File menu allows you to read previously stored data for
display or analysis, write the current set of data to a file for
later use, and exit the program.
Output Data Rate
This text box displays the output data rate of the AD7781.
Gain
About
This text box displays the gain of the AD7781.
The About menu provides information on the revision of
software used.
Status Bits
Buttons
Reset
This text box displays the status bits of the AD7781.
This button allows you to reset the AD7781 software.
The gathered conversions are displayed in graph form.
Exit
Histogram
This button allows you to exit the software. It serves the same
purpose as Quit in the File pull-down menu.
The gathered samples are used to generate a histogram.
Sample
The gathered samples can be displayed in codes or in voltage
format. When the Codes button is selected, the values are
displayed as code. The Codes button changes to Volts. To
display the information in volts, click Volts.
Waveform
This button allows you to read a number of samples from
the AD7781. Noise analysis is then performed on the samples.
These samples can be stored for further analysis. The sample
size is entered in the Num Samples text box.
Continuous
This button allows you to read a number of samples continuously.
The software gathers a number of samples as specified by the
Num Samples text box, performs noise analysis on the samples,
and gathers the next group of samples.
Codes
Reference
Enter the value of the external reference in the Reference (V)
text box.
Rev. 0 | Page 7 of 16
UG-079
Evaluation Board User Guide
WEIGHSCALE DEMO WINDOW
To stop conversions, click the STOP button. To exit the
Weighscale Demo, click the BACK button.
08749-004
Click Weighscale Demo (in the main window) to access
the weighscale demo window (see Figure 4). The AD7781
evaluation board has a header, J3/J4, which allows you to
interface the ADC to a load cell. To connect a load cell to the
AD7781 evaluation board, LK1, LK2, LK3 and LK4 must be
removed. A 6-wire load cell can be connected to J3/J4. With
the load cell connected to the evaluation board, click the
RUN button (the button changes to a STOP button after
being clicked). The software then begins reading conversions
from the AD7781. The output data rate and gain are continuously monitored so you can change either the gain or output
data rate within the weighscale demo window. The output data
rate and gain being used by the AD7781 are reflected in the
Output Data Rate and Gain windows. The maximum weight
being applied to the load cell must be entered in the Full-Scale
Weight (Kg) window. The Zero-Scale Calibration button
performs an offset calibration, which is useful to remove the
load cell TARE. With the full-scale weight placed on the load
cell, a full-scale calibration is performed by clicking the FullScale Calibration button.
Figure 4. AD7781 Evaluation Software Weighscale Demo Window
Rev. 0 | Page 8 of 16
Evaluation Board User Guide
UG-079
EVALUATION BOARD SCHEMATIC AND ARTWORK
08749-005
Figure 5. AD7781 Evaluation Board Schematic
Rev. 0 | Page 9 of 16
Evaluation Board User Guide
08749-006
UG-079
Figure 6. AD7781 Evaluation Board—Solder Side View
Rev. 0 | Page 10 of 16
UG-079
08749-007
Evaluation Board User Guide
Figure 7. AD7781 Evaluation Board—Component Side View
Rev. 0 | Page 11 of 16
Evaluation Board User Guide
08749-008
UG-079
Figure 8. AD7781 Evaluation Board—Component Layout Diagram
Rev. 0 | Page 12 of 16
Evaluation Board User Guide
UG-079
ORDERING INFORMATION
BILL OF MATERIALS
Table 4.
Qty
3
1
1
1
1
2
1
1
4
2
15
3
2
1
2
7
2
4
2
4
1
2
13
2
1
16
4
1
2
1
Reference Designator
Integrated Circuits
U1, U5, U6
U2
U3
U4
Y1
D1, D2
L1
D3
Capacitors
C1 to C4
C5, C6
C8, C9, C11, C15, C16, C18, C22, C23, C25
to C31
C7, C10, C14, C21, C24
C12, C13
C17
C19, C20
Resistors
R1 to R4, R9, R18
R5, R6
R10 to R15
R16, R17
R19
R7, R20
R21, R22
Links
LK1 to LK4, LK6 to LK14, (2 × 1 way)
LK15, LK16 (3 × 1 way)
LK5 (3 × 2 way)
At LK1 to LK16
Connectors
AIN+, AIN−, REFIN+, REFIN−
J1
J3, J4
J2
Description
Manufacturer, Part No.
24-bit Σ-Δ ADC
USB controller
EEPROM
3.3 V Regulator
24 MHz crystal
Green LED
Ferrite bead
Diode
Analog Devices, AD7781BRZ
Cypress Semiconductor Corporation, CY7C68013A-56LFXC
Microchip Technology, Inc., 24LC64-I/SN
Analog Devices, ADP3303ARZ-3.3
AEL Crystals, X24M000000S244
Kingbright, Elec. Co., Ltd, KP-2012SGC
Meggitt Sigma, BMB2A0300AN1
Micro Commercial Components Corp., DL4001-TP
Capacitors
100 pF ceramic
0.1 μF ± 10% ceramic
Not inserted
AVX Corporation, 06035A101JAT2A
AVX Corporation, CM105X7R104K16AT
10 μF tantalum
1 μF ceramic
2.2 μF tantalum
12 pF ceramic
AVX Corporation, TAJA106M016R
Yageo Corporation, 2238 246 19863
EPCOS AG, B45196E2225K109
Phycomp, 2238 867 15129
0 Ω resistor
5 kΩ resistor
1 MΩ resistor
100 kΩ resistor
10 kΩ resistor
1 kΩ resistor
2.2 kΩ resistor
Phycomp, 232270296001
Tyco Electronics, RN73C2A4K99BTG
Multicomp, MC 0.063W 0603 1% 1M
Multicomp, MC 0.063W 0603 1% 100K
Multicomp, MC 0.063W 0603 1% 10K
Multicomp, MC 0.063W 0603 1% 1K
Multicomp, MC 0.063W 0603 1% 2K2
Pin headers
Pin headers
Pin headers
Shorting plugs
Harwin Plc, M20-9990246
Harwin Plc, M20-9990246
Harwin Plc, M20-9980346
Harwin Plc, M7566-05
SMB connector
USB Mini-B connector
3-way terminal block
2-way terminal block
Not inserted
Molex, 565790576
Phoenix, 1725672
Camden Electronics Ltd., CTB5000/2
Rev. 0 | Page 13 of 16
UG-079
Evaluation Board User Guide
NOTES
Rev. 0 | Page 14 of 16
Evaluation Board User Guide
UG-079
NOTES
Rev. 0 | Page 15 of 16
UG-079
Evaluation Board User Guide
NOTES
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2010 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG08749-0-2/10(0)
Rev. 0 | Page 16 of 16
工商网监
湘ICP备2023018690号
