HMC1161LP5E

FUNCTIONAL BLOCK DIAGRAM APPLICATIONS 1 2 3 4 5 6 7 8 HMC1161 NC 9 NC 10 GND 11 RFOUT/2 12 NC 13 NC 14 NC 15 NC 16 Point to point and multipoint radios Test equipment and industrial controls Very small aperture terminals (VSATs) NC NC NC NC GND NC NC NC 24 23 22 21 20 19 18 17 NC NC NC VCC NC RFOUT NC NC 13382-001 Dual output frequency range fOUT = 8.71 GHz to 9.55 GHz fOUT/2 = 4.355 GHz to 4.775 GHz Output power (POUT): 11 dBm Single-sideband (SSB) phase noise: −115 dBc/Hz at 100 kHz No external resonator needed RoHS-compliant, 5 mm × 5 mm, 32-lead LFCSP: 25 mm² NC NC NC VTUNE NC NC NC NC FEATURES 32 31 30 29 28 27 26 25 Data Sheet 8.71 GHz to 9.55 GHz MMIC VCO with Half Frequency Output HMC1161 Figure 1. GENERAL DESCRIPTION The HMC1161 is a monolithic microwave integrated circuit (MMIC), voltage controlled oscillator (VCO) that integrates a resonator, a negative resistance device, and a varactor diode, and features a half frequency output. Rev. B Because of the monolithic construction of the oscillator, the output power and phase noise performance are excellent over temperature. The output power is 11 dBm typical from a 5 V supply voltage. The VCO is housed in a RoHS-compliant LFCSP and requires no external matching components. Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2015 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com HMC1161 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Interface Schematics .....................................................................6 Applications ....................................................................................... 1 Typical Performance Characteristics ..............................................7 Functional Block Diagram .............................................................. 1 Applications Information .................................................................9 General Description ......................................................................... 1 Evaluation Printed Circuit Board (PCB) ..................................... 10 Revision History ............................................................................... 2 Bill of Materials ........................................................................... 10 Specifications..................................................................................... 3 Packaging and Ordering Information ......................................... 11 Absolute Maximum Ratings ....................................................... 4 Outline Dimensions ................................................................... 11 ESD Caution .................................................................................. 4 Ordering Guide .......................................................................... 11 Pin Configuration and Function Descriptions ............................. 5 REVISION HISTORY 11/15—Rev. A to Rev. B Changes to Figure 3 and Figure 4 ................................................... 6 Changes to Ordering Guide, Note 1............................................. 11 8/15—Revision A: Initial Version This Hittite Microwave Products data sheet has been reformatted to meet the styles and standards of Analog Devices, Inc. Rev. B | Page 2 of 11 Data Sheet HMC1161 SPECIFICATIONS TA = −40°C to +85°C, VCC = 5 V, unless otherwise noted. Table 1. Parameter FREQUENCY Range Output Frequency (fOUT) Half Output Frequency (fOUT/2) Drift Rate Pulling Pushing OUTPUT POWER (POUT) RFOUT RFOUT/2 Supply Current (ICC) Min 8.71 4.355 Max Unit 9.55 4.755 GHz GHz 0.75 3.5 2 8 0 200 HARMONICS, SUBHARMONICS 1/2 3/2 Second Third TUNING Voltage (VTUNE) Sensitivity Tune Port Leakage Current OUTPUT RETURN LOSS SSB PHASE NOISE 10 kHz Offset 100 kHz Offset Typ 11 4 230 250 270 16 8 300 23 40 20 30 2 50 MHz/°C MHz p-p MHz/V Pulling into a 2.0:1 voltage standing wave ratio (VSWR) At VTUNE = 5 V dBm dBm mA mA mA VCC = 4.75 V VCC = 5.00 V VCC = 5.25 V dBc dBc dBc dBc 13 250 10 V MHz/V µA dB −83 −109 dBc/Hz dBc/Hz 2.5 −90 −115 Test Conditions/Comments VTUNE = 13 V Rev. B | Page 3 of 11 HMC1161 Data Sheet ABSOLUTE MAXIMUM RATINGS Table 2. Parameter VCC VTUNE Temperature Operating Storage Nominal Junction (to Maintain 1 Million Hours Mean Time to Failure (MTTF)) Nominal Junction (TA = 85°C) Maximum Reflow Temperature (MSL3 Rating) Thermal Resistance (Junction to Ground Paddle) ESD Sensitivity (Human Body Model) Rating 5.5 V dc 0 V to 15 V −40°C to +85°C −65°C to +150°C 135°C Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. ESD CAUTION 126.7°C 260°C 31.4°C/W Class 1A Rev. B | Page 4 of 11 Data Sheet HMC1161 32 31 30 29 28 27 26 25 NC NC NC VTUNE NC NC NC NC PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 1 2 3 4 5 6 7 8 HMC1161 TOP VIEW (Not to Scale) 24 23 22 21 20 19 18 17 NC NC NC VCC NC RFOUT NC NC NOTES 1. NC = NO CONNECT. HOWEVER, THESE PINS CAN BE CONNECTED TO RF/DC GROUND WITHOUT AFFECTING THE PERFORMANCE OF THE DEVICE. 2. EXPOSED PAD. THE PACKAGE BOTTOM HAS AN EXPOSED METAL PAD THAT MUST BE CONNECTED TO RF/DC GROUND. 13382-002 NC 9 NC 10 GND 11 RFOUT/2 12 NC 13 NC 14 NC 15 NC 16 NC NC NC NC GND NC NC NC Figure 2. Pin Configuration Table 3. Pin Function Descriptions Pin No. 1 to 4, 6 to 10, 13 to 18, 20, 22 to 28, 30 to 32 5, 11 12 19 21 29 Mnemonic NC GND RFOUT/2 RFOUT VCC VTUNE EP Description No Connect. However, these pins can be connected to RF/dc ground without affecting the performance of the device. Ground. These pins must be connected to RF/dc ground. Half Frequency Output. This pin is ac-coupled. RF Output. This pin is ac-coupled. Supply Voltage (5 V). Control Voltage and Modulation Input. The modulation bandwidth is dependent on the drive source impedance. Exposed Pad. The package bottom has an exposed metal pad that must be connected to RF/dc ground. Rev. B | Page 5 of 11 HMC1161 Data Sheet INTERFACE SCHEMATICS 3nH 4pF Figure 3. RFOUT/2 Interface 43pF Figure 6. VTUNE Interface GND Figure 4. RFOUT Interface Figure 7. GND Interface 15pF 13382-005 VCC 13382-007 13382-003 RFOUT Figure 5. VCC Interface Rev. B | Page 6 of 11 13382-006 RFOUT/2 13382-004 VTUNE Data Sheet HMC1161 TYPICAL PERFORMANCE CHARACTERISTICS 10.0 300 290 +85°C +25°C –40°C 280 SUPPLY CURRENT (mA) OUTPUT FREQUENCY (GHz) 9.5 9.0 8.5 +85°C +25°C –40°C 8.0 270 260 250 240 230 220 7.5 0 1 2 3 4 5 6 7 8 9 10 11 12 13 TUNING VOLTAGE (V dc) 200 13382-008 7.0 0 2 3 4 5 6 7 8 9 10 12 13 Figure 11. Supply Current (ICC) vs. Tuning Voltage 5.00 RFOUT/2 OUTPUT FREQUENCY (GHz) 14 12 10 8 +85°C +25°C –40°C 6 4 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 TUNING VOLTAGE (V dc) 4.50 4.25 +85°C +25°C –40°C 4.00 3.75 3.50 13382-009 2 4.75 0 1 2 3 4 5 6 7 8 9 10 11 12 13 TUNING VOLTAGE (V dc) 13382-012 16 Figure 12. RFOUT/2 Output Frequency vs. Tuning Voltage Figure 9. Output Power vs. Tuning Voltage 600 10 9 RFOUT/2 OUTPUT POWER (dBm) 500 400 300 +85°C +25°C –40°C 200 100 +85°C +25°C –40°C 8 7 6 5 4 3 2 0 0 1 2 3 4 5 6 7 8 9 10 TUNING VOLTAGE (V dc) 11 12 13 Figure 10. Sensitivity vs. Tuning Voltage 0 0 1 2 3 4 5 6 7 8 9 10 11 12 TUNING VOLTAGE (V dc) Figure 13. RFOUT/2 Output Power vs. Tuning Voltage Rev. B | Page 7 of 11 13 13382-013 1 13382-010 SENSITIVITY (MHz/V) 11 TUNING VOLTAGE (V dc) Figure 8. Output Frequency vs. Tuning Voltage OUTPUT POWER (dBm) 1 13382-011 210 HMC1161 Data Sheet –70 –75 –60 SSB PHASE NOISE (dBc/Hz) –80 10kHz –90 –95 –100 –105 –110 100kHz –120 1 2 3 4 5 6 7 –70 –80 –90 –100 –110 –120 –130 –115 0 +85°C +25°C –40°C 8 9 10 11 TUNING VOLTAGE (V dc) 12 13 –140 10k 100k 1M 10M OFFSET FREQUENCY (Hz) Figure 15. SSB Phase Noise vs. Offset Frequency at VTUNE = 5 V Figure 14. SSB Phase Noise vs. Tuning Voltage Rev. B | Page 8 of 11 13382-015 –85 13382-014 SSB PHASE NOISE (dBc/Hz) –50 +85°C +25°C –40°C Data Sheet HMC1161 APPLICATIONS INFORMATION The HMC1161 serves as the local oscillator (LO) in microwave synthesizer applications. The primary applications are point-topoint microwave radios, military, radars, test and measurement, as well as industrial and medical equipment. The low phase noise allows higher orders of modulation and offers improved bit error rates in communication systems, whereas the linear, monotonic tuning sensitivity allows a stable loop filter design. The higher output power minimizes the gain required to drive subsequent stages. The half frequency output reduces the input frequency to the prescaler without the addition of residual phase noise to the input of the phase-locked loop synthesizer. LOOP FILTER HOST SCK SDI SEN SYNTH CP RFOUT RFOUT/2 REF XREFP VCO INPUT Figure 16. Typical Application Diagram Rev. B | Page 9 of 11 13382-016 VTUNE HMC1161 Data Sheet 13382-017 EVALUATION PRINTED CIRCUIT BOARD (PCB) Figure 17. Evaluation PCB The circuit board used in an application uses RF circuit design techniques. Ensure that the signal lines have 50 Ω impedance and that the package ground leads and backside ground paddle are connected directly to the ground plane. Use a sufficient number of via holes to connect the top and bottom ground planes. The evaluation circuit board shown in Figure 17 is available from Analog Devices, Inc., upon request. BILL OF MATERIALS Table 4. Bill of Materials for the EV1HMC1161LP5 Item J1 to J4 J5, J6 C1 to C3 C4 C5 to C7 C8 U1 PCB1 1 2 Description PCB mount SMA RF connectors 2 mm dc headers 100 pF capacitors, 0402 package 1000 pF capacitor, 0402 package 2.2 μF tantalum capacitors 0.01 μF capacitor, 0603 package HMC1161 VCO 110225 evaluation board2 Circuit board material is Rogers 4350. Reference this number when ordering the complete evaluation PCB. Rev. B | Page 10 of 11 Data Sheet HMC1161 PACKAGING AND ORDERING INFORMATION OUTLINE DIMENSIONS 0.30 0.25 0.18 1 24 0.50 BSC 3.80 3.65 SQ 3.50 EXPOSED PAD 17 TOP VIEW 1.00 0.90 0.80 8 16 9 BOTTOM VIEW 3.50 REF 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF SEATING PLANE PKG-000000 0.45 0.40 0.35 PIN 1 INDICATOR 32 25 0.20 MIN FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. 03-04-2015-A PIN 1 INDICATOR 5.10 5.00 SQ 4.90 COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-4. Figure 18. 32-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 5 mm × 5 mm Body, Very Thin Quad (HCP-32-1) Dimensions shown in millimeters ORDERING GUIDE Model1 HMC1161LP5E Temperature Range −40°C to +85°C MSL Rating2 MSL3 Package Description 32-Lead LFCSP_VQ Package Option HCP-32-1 Qty. HMC1161LP5ETR −40°C to +85°C MSL3 32-Lead LFCSP_VQ, 7” Tape and Reel HCP-32-1 500 EV1HMC1161LP5 1 2 3 Evaluation Board The HMC1161LP5E and HMC1161LP5ETR are RoHS compliant parts. See the Absolute Maximum Ratings section, Table 2. XXXX is a placeholder for the 4-digit lot number. ©2015 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D13382-0-11/15(B) www.analog.com/HMC1161 Rev. B | Page 11 of 11 Branding3 H1161 XXXX H1161 XXXX