HMC597LP4TR

HMC597LP4 / 597LP4E v07.1213 Typical Applications Features The HMC597LP4 / HMC597LP4E is suitable for various modulation systems: High Linearity: +23 dBm IIP3 & +60 dBm IIP2 • Cellular/PCS/3G High Integration: On-Chip RF Balun Low Noise Figure: 15 dB • Base Stations & Repeaters • GSM/GPRS, WCDMA & TD-SCDMA The HMC597LP4(E) are highly integrated SiGe wideband direct conversion I/Q Demodulator RFICs which are ideal for high dynamic range receivers operating from 100 - 4000 MHz in cellular and broadband wireless infrastructure applications. Providing a very high level of integration compared with discrete solutions, the HMC597LP4(E) features an on-chip RF balun which allows for singled ended RF input. An off-chip capacitor allows the reconfiguration of the RF port to operate over the whole 100 - 4000 MHz band without additional off-chip components. Also ideal for software radio and other multi-band receivers, the HMC597LP4(E) demodulator is housed in a compact 4 x 4 mm SMT QFN package and delivers exceptionally high dynamic range. The LO requires -6 to +6 dBm and can be driven in single-ended mode. The I and Q output ports are differential with an output impedance of 400 Ohms, allowing direct connection to channel filters and ADCs. This device is optimized for a supply voltage of +4.5V to +5.5V and consumes 200 mA @ +5V supply. LE Functional Diagram General Description TE • WiMAX, WiBro & Fixed Wireless B SO Demodulators - SMT SiGe WIDEBAND DIRECT DEMODULATOR RFIC, 100 - 4000 MHz Electrical Specifications, See Test Conditions on following page herein. O Parameter Min. RF Input Frequency (Direct LO) Input P1dB SSB Noise Figure Input IP3 Typ. Max. Units 0.1 - 4.0 GHz 12 dBm 15 dB +20 +23 -5 -3.5 -2 I/Q Gain Mismatch 0.1 0.25 LO to RF Leakage @ +3 dBm LO -66 IF Port Bandwidth 600 MHz IF Output Impedance (Diff.) 400 Ohms -6 to +6 dBm Input IP2 Conversion Gain LO Input Power +26 +60 LO/RF Return Loss 12/12 Total Supply Current 200 dBm dBm dB dB dBm dB 230 mA [1] Data taken at 1970 MHz RF Input frequency for two tone test, fundamental frequencies are 1970 MHz and 1971 MHz. 1 Information furnished by Analog Devices is believed to be accurate andMicrowave reliable. However, no For price,2delivery, and Drive, to placeChelmsford, orders: AnalogMA Devices, For price, delivery and to place orders: Hittite Corporation, Elizabeth 01824Inc., responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Phone: 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC597LP4 / 597LP4E v07.1213 SiGe WIDEBAND DIRECT DEMODULATOR RFIC, 100 - 4000 MHz AC Test Conditions [1] Parameter Condition Parameter Condition Supply 200 mA @ +5V RF Input Frequency 1970 MHz 124 mA @ +2.8V RF Input Frequency for IIP3 1970 & 1971 MHz 76 mA @ +3.5V RF Input Power for IIP3 0 dBm per Tone LO Frequency 1960 MHz LO Input Power 0 dBm single ended through LOP VccLO [2] QN, QP, IN, IP [2] [1] Unless otherwise specified, the following test conditions were used. Please refer to the HMC597LP4(E) application schematic. LE P1dB, Noise Figure, Gain vs. Frequency [1] Input IP3 vs. Frequency [1] 40 C26= 0pF C26= 6.8pF C26= 0.9pF 20 NF 15 10 35 30 P1dB 5 0 -5 INPUT IP3 (dBm) 25 B SO NF (dB), P1dB (dBm) & GAIN (dB) 30 TE [2] Voltages at these pins are supplied through bias resistors from Vsupply, 5V (see application circuit). Power dissipation on chip is 124 x 2.8 + 76 x 3.5 = 613.2 mW. Thermal rise calculations should be based on this power dissipation level. 0 0.5 1 1.5 2 2.5 3 3.5 25 20 15 10 C26= 0pF C26= 6.8pF C26= 0.9pF 5 GAIN -10 0 4 0 0.5 1 RF FREQUENCY (GHz) 1.5 2 2.5 3 3.5 4 3.5 4 RF FREQUENCY (GHz) LO & Return Loss vs. Frequency O RF Return Loss vs. Frequency 0 0 C26=0pF RETURN LOSS (dB) RF RETURN LOSS (dB) Demodulators - SMT DC Test Conditions [1] -5 C26=6.8pF -10 -5 -10 -15 C26=0.9pF -15 -20 0 0.5 1 1.5 2 2.5 RF FREQUENCY (GHz) 3 3.5 4 0 0.5 1 1.5 2 2.5 3 RF FREQUENCY (GHz) [1] IF Frequency= 10 MHz Information furnished by Analogand Devices believedorders: to be accurate and Microwave reliable. However,Corporation, no For price, 2delivery, and Drive, to placeChelmsford, orders: AnalogMA Devices, Inc., For price, delivery to isplace Hittite Elizabeth 01824 responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order 781-329-4700 On-line at www.hittite.com • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com 2 HMC597LP4 / 597LP4E v07.1213 SiGe WIDEBAND DIRECT DEMODULATOR RFIC, 100 - 4000 MHz Noise Figure, P1dB, Gain @ 900 MHz vs. LO Power [1] LO - RF Isolation vs. Frequency 25 -60 -80 NF 20 15 10 P1dB 5 0 TE NF (dB), P1dB (dBm) & GAIN (dB) -40 -5 GAIN -10 0 0.5 1 1.5 2 2.5 3 3.5 -9 4 -6 -3 0 3 6 9 LO POWER (dBm) RF FREQUENCY (GHz) 25 Noise Figure, P1dB, Gain @ 3500 MHz vs. LO Power [1] LE Noise Figure, P1dB, Gain @ 1970 MHz vs. LO Power [1] 25 20 NF 15 10 5 0 -5 B SO P1dB GAIN -10 -9 -6 -3 0 3 6 9 NF 20 15 10 P1dB 5 0 -5 GAIN -10 -9 -6 -3 0 3 6 9 LO POWER (dBm) O LO POWER (dBm) NF (dB), P1dB (dBm) & GAIN (dB) LO-RF ISOLATION (dB) -20 -100 NF (dB), P1dB (dBm) & GAIN (dB) Demodulators - SMT 0 [1] IF Frequency = 10 MHz 3 Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 2delivery, and Drive, to placeChelmsford, orders: AnalogMA Devices, Inc., For price, delivery and to place orders: Hittite Microwave Corporation, Elizabeth 01824 responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order 781-329-4700 On-line at www.hittite.com • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC597LP4 / 597LP4E v07.1213 SiGe WIDEBAND DIRECT DEMODULATOR RFIC, 100 - 4000 MHz +12 dBm Channel Temperature 150 °C Thermal Resistance (Rth) (channel to ground paddle) 8.9 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C ESD Sensitivity (HBM) Class 1B ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS TE +6V LO Input Power LE Vcc1, Vcc2 B SO Outline Drawing Demodulators - SMT Absolute Maximum Ratings NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY O 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. P  AD BURR LENGTH SHALL BE 0.15 mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05 mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05 mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC597LP4 Low Stress Injection Molded Plastic Sn / Pb Solder MSL1 [1] HMC597LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 [2] Package Marking [3] H597 XXXX H597 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX Information furnished by Analogand Devices believedorders: to be accurate and Microwave reliable. However,Corporation, no For price, 2delivery, and to placeChelmsford, orders: Analog MA Devices, Inc., For price, delivery to isplace Hittite Elizabeth Drive, 01824 responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order781-329-4700 On-line at www.hittite.com • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks areApplication the property of their respective owners. Support: Phone: 978-250-3343 or apps@hittite.com 4 HMC597LP4 / 597LP4E v07.1213 SiGe WIDEBAND DIRECT DEMODULATOR RFIC, 100 - 4000 MHz Function Description Interface Schematic 1 VccLO Supply for LO Amplifier. Typically draws 124mA @ 2.8V. 2, 5, 8, 11, 12, 14, 17, 19, 20, 23 GND These pins and the ground paddle should be connected to a high quality RF/DC ground. 3 LOP LO input. Need a DC decoupling capacitor. Typically at 1.5 - 1.8 VDC. 4 LON This pin should be AC grounded. Also can be used to optimize the IP2 performances 6, 7, 24 N/C Not Connected 9, 10 QN, QP 21, 22 IP, IN LE TE Pin Number O B SO Demodulators - SMT Pin Descriptions 5 Differential baseband outputs. 400 Ohms differential output impedance. Each port should draw 38 mA @ 3.5V. 12, 19 VccQ, VccI Decoupling for the Q and I mixer stages. 13, 18 CTRFQ, CTRFI Center tap of the RF transformer. Should be connected to a high quality RF/DC ground. Information furnished by Analogand Devices believedorders: to be accurate and Microwave reliable. However,Corporation, no For price, 2delivery, and Drive, to placeChelmsford, orders: AnalogMA Devices, Inc., For price, delivery to isplace Hittite Elizabeth 01824 responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order 781-329-4700 On-line at www.hittite.com • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC597LP4 / 597LP4E v07.1213 SiGe WIDEBAND DIRECT DEMODULATOR RFIC, 100 - 4000 MHz Pin Descriptions (Continued) Description Interface Schematic 15 RFN RF Input. 16 RFP Can be DC or RF grounded. This pin is used to match the RF port over the desired frequency range. Also can be used to drive the RF port differentially if needed. LE O B SO Demodulators - SMT Function TE Pin Number Information furnished by Analog and Devices believedorders: to be accurate and Microwave reliable. However,Corporation, no For price, 2 delivery, and to place Chelmsford, orders: Analog MA Devices, Inc., For price, delivery toisplace Hittite Elizabeth Drive, 01824 responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that mayPhone: result from 978-250-3343 its use. Specifications subject to change without notice. No Fax: 978-250-3373 Phone: Order781-329-4700 On-line at www.hittite.com • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks areApplication the property of their respective owners. Support: Phone: 978-250-3343 or apps@hittite.com 6 HMC597LP4 / 597LP4E v07.1213 SiGe WIDEBAND DIRECT DEMODULATOR RFIC, 100 - 4000 MHz B SO LE TE Demodulators - SMT Evaluation PCB Evaluation PCB 115775 [1][2] Item J1 - J6 PCB Mount SMA Connector 2 mm DC Header O J7, J8 Description C11, C20 - C24 1000 pF Capacitor, 0402 Pkg. C12 100 pF Capacitor, 0402 Pkg. C25 0.3 pF Capacitor, 0402 Pkg. C26 0.9 pF Capacitor, 0402 Pkg. C30 - C32 0.1 µF Capacitor, 0805 Pkg. R3, R4 39.2 Ohm Resistor, 0402 Pkg. R5 18.2 Ohm Resistor, 0402 Pkg. L1 - L4 5.6 nH Inductor, 0402 Pkg. T1, T2 2 - 800 MHz Balun U1 HMC597LP3 / HMC597LP3E Direct Demodulator PCB [2] 116265 Evaluation PCB The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 7 Information furnished by Analogand Devices is believed to be accurate andMicrowave reliable. However, no For price,2delivery, and Drive, to placeChelmsford, orders: AnalogMA Devices, Inc., For price, delivery to place orders: Hittite Corporation, Elizabeth 01824 responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Phone: 781-329-4700 • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC597LP4 / 597LP4E v07.1213 SiGe WIDEBAND DIRECT DEMODULATOR RFIC, 100 - 4000 MHz Demodulators - SMT O B SO LE TE Application & Evaluation PCB Schematic * Short to ground for single ended mode. Information furnished by Analogand Devices believedorders: to be accurate and Microwave reliable. However,Corporation, no For price, 2delivery, and Drive, to placeChelmsford, orders: AnalogMA Devices, Inc., For price, delivery to isplace Hittite Elizabeth 01824 responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Phone: Order 781-329-4700 On-line at www.hittite.com • Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com 8