LT1170/LT1171/LT1172
100kHz, 5A, 2.5A and 1.25A
High Efficiency Switching Regulators
Features
Description
Wide Input Voltage Range: 3V to 60V
n Low Quiescent Current: 6mA
n Internal 5A Switch
(2.5A for LT1171, 1.25A for LT1172)
n Shutdown Mode Draws Only 50µA Supply Current
n Very Few External Parts Required
n Self-Protected Against Overloads
n Operates in Nearly All Switching Topologies
n Flyback-Regulated Mode Has Fully Floating Outputs
n Comes in Standard 5-Pin Packages
n LT1172 Available in 8-Pin MiniDIP and
Surface Mount Packages
n Can Be Externally Synchronized
The LT®1170/LT1171/LT1172 are monolithic high powerswitching regulators. They can be operated in all standard
switching configurations including buck, boost, flyback,
forward, inverting and “Cuk.” A high current, high efficiency
switch is included on the die along with all oscillator, control and protection circuitry. Integration of all functions
allows the LT1170/LT1171/LT1172 to be built in a standard
5-pin TO-3 or TO-220 power package as well as the 8-pin
packages (LT1172). This makes them extremely easy to
use and provides “bust proof” operation similar to that
obtained with 3-pin linear regulators.
n
Applications
n
n
n
n
n
Logic Supply 5V at 10A
5V Logic to ±15V Op Amp Supply
Battery Upconverter
Power Inverter (+ to –) or (– to +)
Fully Floating Multiple Outputs
USER NOTE:
This data sheet is only intended to provide specifications, graphs, and a general functional
description of the LT1170/LT1171/LT1172. Application circuits are included to show the capability
of the LT1170/LT1171/LT1172. A complete design manual (AN19) should be obtained to assist in
developing new designs. This manual contains a comprehensive discussion of both the LT1070
and the external components used with it, as well as complete formulas for calculating the values
of these components. The manual can also be used for the LT1170/LT1171/LT1172 by factoring in
the higher frequency. A CAD design program called SwitcherCAD is also available.
The LT1170/LT1171/LT1172 operate with supply voltages
from 3V to 60V, and draw only 6mA quiescent current.
They can deliver load power up to 100W with no external power devices. By utilizing current-mode switching
techniques, they provide excellent AC and DC load and
line regulation.
The LT1170/LT1171/LT1172 have many unique features not
found even on the vastly more difficult to use low power
control chips presently available. They use adaptive antisat
switch drive to allow very wide ranging load currents with
no loss in efficiency. An externally activated shutdown
mode reduces total supply current to 50µA typically for
standby operation.
L, LT, LTC, LTM, Linear Technology, the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
Typical Application
Boost Converter (5V to 12V)
L1**
50µH
D1
MBR330
VIN
VSW
+
LT1170
C3*
100µF
L2
10µH
+
OUTPUT
FILTER
* ROUGH GUIDE ONLY. BUCK MODE
POUT = (5A)(VOUT)
SPECIAL TOPOLOGIES DELIVER
MORE POWER.
** DIVIDE VERTICAL POWER SCALE
BY TWO FOR LT1171, BY FOUR
FOR LT1172.
LT1170
80
C3
100µF
C2
1000µF
R1
10.7k
1%
12V
1A
POWER (W) **
5V
Maximum Output Power*
100
BUCK-BOOST
VO = 30V
60
BOOST
LT1170/1/2 TA02
FLYBACK
40
FB
GND
20
VC
R2
1.24k
1%
R3
1k
C1
1µF
*REQUIRED IF INPUT LEADS ≥ 2"
** COILTRONICS 50-2-52
PULSE ENGINEERING 92114
0
BUCK-BOOST
VO = 5V
0
10
30
20
INPUT VOLTAGE (V)
40
50
1170/1/2 TA01
For more information www.linear.com/LT1170
117012fi
1
LT1170/LT1171/LT1172
Absolute Maximum Ratings
(Note 1)
Supply Voltage
LT1170/LT1171/LT1172HV (Note 2)........................60V
LT1170/LT1171/LT1172 (Note 2).............................40V
Switch Output Voltage
LT1170/LT1171/LT1172HV......................................75V
LT1170/LT1171/LT1172..........................................65V
LT1172S8...............................................................60V
Feedback Pin Voltage (Transient, 1ms).................... ±15V
Storage Temperature Range................... –65°C to 150°C
Lead Temperature (Soldering, 10 sec..................... 300°C
Operating Junction Temperature Range
LT1170M/LT1171M (OBSOLETE)........ –55°C to 150°C
LT1172M (OBSOLETE)........................ –55°C to 125°C
LT1170/LT1171/LT1172HVC,
LT1170/LT1171/LT1172C (Oper.).............. 0°C to 100°C
LT1170/LT1171/LT1172HVC
LT1170/LT1171/LT1172C (Sh. Ckt.)......... 0°C to 125°C
LT1170/LT1171/LT1172HVI,
LT1170/LT1171/LT1172I (Oper.)........... –40°C to 100°C
LT1170/LT1171/LT1172HVI,
LT1170/LT1171/LT1172I (Sh. Ckt.)....... –40°C to 125°C
Pin Configuration
BOTTOM VIEW
VSW
TOP VIEW
GND 1
8
E2
VC 2
7
VSW
FB 3
6
E1
NC* 4
5
VIN
J8 PACKAGE
8-LEAD CERDIP
TJMAX = 125°C, θJA = 100°C/W
* Do not connect Pin 4 of the LT1172 DIP or SO to external
circuitry. This pin may be active in future revisions.
OBSOLETE
VC
1
4
2
3
TOP VIEW
CASE
IS GND
VIN
FB
K PACKAGE
4-LEAD TO-3 METAL CAN
LT1170MK: TJMAX = 150°C, θJC = 2°C/W, θJA = 35°C/W
LT1170CK: TJMAX = 100°C, θJC = 2°C/W, θJA = 35°C/W
LT1171MK: TJMAX = 150°C, θJC = 4°C/W, θJA = 35°C/W
LT1171CK: TJMAX = 100°C, θJC = 4°C/W, θJA = 35°C/W
LT1172MK: TJMAX = 150°C, θJC = 8°C/W, θJA = 35°C/W
LT1172CK: TJMAX = 100°C, θJC = 8°C/W, θJA = 35°C/W
Based on continuous operation.
TJMAX = 125°C for intermittent fault conditions.
OBSOLETE
GND 1
8
E2
VC 2
7
VSW
FB 3
6
E1
NC* 4
5
VIN
N8 PACKAGE
8-LEAD PDIP
S8 PACKAGE
8-LEAD PLASTIC SO
TJMAX = 100°C, θJA = 100°C/W (N)
TJMAX = 100°C, θJA = 120°C/W to 150°C/W
depending on board layout (S)
* Do not connect Pin 4 of the LT1172 DIP or SO to external
circuitry. This pin may be active in future revisions.
TOP VIEW
FRONT VIEW
TAB IS
GND
5
4
3
2
1
VIN
VSW
GND
FB
VC
Q PACKAGE
5-LEAD DD
TJMAX = 100°C, θJA = *°C/W
* θ will vary from approximately 25°C/W with 2.8 sq.
in. of 1oz. copper to 45°C/W with 0.20 sq. in. of 1oz.
copper. Somewhat lower values can be obtained with
additional copper layers in multilayer boards.
2
NC 1
16 NC
NC 2
15 NC
GND 3
14 E2
TAB IS
GND
FRONT VIEW
5
VIN
4
VSW
VC 4
13 VSW
3
GND
FB 5
12 E1
2
FB
NC 6
11 VIN
1
VC
NC 7
10 NC
NC 8
9
NC
SW PACKAGE
16-LEAD PLASTIC SO WIDE
TJMAX = 100°C, θJA = 150°C/W
Based on continuous operation.
TJMAX = 125°C for intermittent fault conditions.
T PACKAGE
5-LEAD PLASTIC TO-220
LT1170CT/LT1170HVCT: TJMAX =100°C, θJC = 2°C/W, θJA = 75°C/W
LT1171CT/LT1171HVCT: TJMAX =100°C, θJC = 4°C/W, θJA = 75°C/W
LT1172CT/LT1172HVCT: TJMAX =100°C, θJC = 8°C/W, θJA = 75°C/W
Based on continuous operation.
TJMAX = 125°C for intermittent fault conditions.
117012fi
For more information www.linear.com/LT1170
LT1170/LT1171/LT1172
Order Information
http://www.linear.com/product/LT1170#orderinfo
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT1172MJ8 (OBSOLETE)
LT1172MJ8#TR
LT1172
8-Lead CERDIP
–55°C to 125°C
LT1172CJ8#PBF (OBSOLETE)
LT1172CJ8#TRPBF
8-Lead CERDIP
0°C to 100°C
LT1170MK#PBF (OBSOLETE)
LT1170MK#TRPBF
4-Lead TO-3 Metal Can
–55°C to 125°C
LT1170CK#PBF (OBSOLETE)
LT1170CK#TRPBF
4-Lead TO-3 Metal Can
0°C to 100°C
LT1171MK#PBF (OBSOLETE)
LT1171MK#TRPBF
4-Lead TO-3 Metal Can
–55°C to 125°C
LT1171CK#PBF (OBSOLETE)
LT1171CK#TRPBF
4-Lead TO-3 Metal Can
0°C to 100°C
LT1172MK#PBF (OBSOLETE)
LT1172MK#TRPBF
4-Lead TO-3 Metal Can
–55°C to 125°C
LT1172CK#PBF (OBSOLETE)
LT1172CK#TRPBF
4-Lead TO-3 Metal Can
0°C to 100°C
LT1172CN8#PBF
LT1172CN8#TRPBF
LT1172
8-Lead PDIP or 8-Lead Plastic SO
0°C to 100°C
LT1172IN8#PBF
LT1172IN8#TRPBF
LT1172
8-Lead PDIP or 8-Lead Plastic SO
–40°C to 100°C
LT1172CS8#PBF
LT1172CS8#TRPBF
1172
8-Lead PDIP or 8-Lead Plastic SO
0°C to 100°C
LT1172IS8#PBF
LT1172IS8#TRPBF
1172I
8-Lead PDIP or 8-Lead Plastic SO
–40°C to 100°C
LT1170CQ#PBF
LT1170CQ#TRPBF
LT1170
5-Lead DD
0°C to 100°C
LT1170IQ#PBF
LT1170IQ#TRPBF
LT1170
5-Lead DD
–40°C to 100°C
LT1170HVCQ#PBF
LT1170HVCQ#TRPBF
LT1170HV
5-Lead DD
0°C to 100°C
LT1171CQ#PBF
LT1171CQ#TRPBF
LT1171
5-Lead DD
0°C to 100°C
LT1171IQ#PBF
LT1171IQ#TRPBF
LT1171
5-Lead DD
–40°C to 100°C
LT1171HVCQ#PBF
LT1171HVCQ#TRPBF
LT1171HV
5-Lead DD
0°C to 100°C
LT1171HVIQ#PBF
LT1171HVIQ#TRPBF
LT1171HV
5-Lead DD
–40°C to 100°C
LT1172CQ#PBF
LT1172CQ#TRPBF
LT1172
5-Lead DD
0°C to 100°C
LT1172HVCQ#PBF
LT1172HVCQ#TRPBF
LT1172HV
5-Lead DD
0°C to 100°C
LT1172HVIQ#PBF
LT1172HVIQ#TRPBF
LT1172HV
5-Lead DD
–40°C to 100°C
LT1172CSW#PBF
LT1172CSW#TRPBF
LT1172CSW
16-Lead Plastic SO Wide
0°C to 100°C
LT1170CT#PBF
LT1170CQ#TRPBF
LT1170
5-Lead Plastic TO-220
0°C to 100°C
LT1170IT#PBF
LT1170IT#TRPBF
LT1170
5-Lead Plastic TO-220
–40°C to 100°C
LT1170HVCT#PBF
LT1170HVCT#TRPBF
LT1170HV
5-Lead Plastic TO-220
0°C to 100°C
LT1170HVIT#PBF
LT1170HVIT#TRPBF
LT1170
5-Lead Plastic TO-220
–40°C to 100°C
LT1171CT#PBF
LT1171CT#TRPBF
LT1171
5-Lead Plastic TO-220
0°C to 100°C
LT1171IT#PBF
LT1171IT#TRPBF
LT1171
5-Lead Plastic TO-220
–40°C to 100°C
LT1171HVCT#PBF
LT1171HVCT#TRPBF
LT1171HV
5-Lead Plastic TO-220
0°C to 100°C
LT1171HVIT#PBF
LT1171HVIT#TRPBF
LT1171HV
5-Lead Plastic TO-220
–40°C to 100°C
LT1172CT#PBF
LT1172CT#TRPBF
LT1172
5-Lead Plastic TO-220
0°C to 100°C
LT1172HVCT#PBF
LT1172HVCT#TRPBF
LT1172HV
5-Lead Plastic TO-220
0°C to 100°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/. Some packages are available in 500 unit reels through
designated sales channels with #TRMPBF suffix.
117012fi
For more information www.linear.com/LT1170
3
LT1170/LT1171/LT1172
Electrical
Characteristics
The
l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 15V, VC = 0.5V, VFB = VREF, output pin open, unless otherwise noted.
SYMBOL PARAMETER
VREF
IB
Reference Voltage
Feedback Input Current
CONDITIONS
MIN
TYP
MAX
UNITS
Measured at Feedback Pin
VC = 0.8V
1.224
1.214
1.244
1.244
1.264
1.274
V
V
350
750
1100
nA
nA
l
VFB = VREF
l
gm
Error Amplifier Transconductance
Error Amplifier Source or Sink Current
AV
∆IC = ±25µA
6000
7000
µmho
µmho
150
120
200
l
350
400
µA
µA
2.30
0.52
V
V
0.03
%/V
VC = 1.5V
Error Amplifier Clamp Voltage
Hi Clamp, VFB = 1V
Lo Clamp, VFB = 1.5V
Reference Voltage Line Regulation
3V ≤ VIN ≤ VMAX
VC = 0.8V
Error Amplifier Voltage Gain
0.9V ≤ VC ≤ 1.4V
1.80
0.25
500
Supply Current
3V ≤ VIN ≤ VMAX, VC = 0.6V
Control Pin Threshold
Duty Cycle = 0
Normal/Flyback Threshold on Feedback Pin
Flyback Reference Voltage (Note 5)
IFB = 50µA
l
Change in Flyback Reference Voltage
0.05 ≤ IFB ≤ 1mA
Flyback Reference Voltage Line Regulation
(Note 5)
IFB = 50µA
7V ≤ VIN ≤ VMAX
Flyback Amplifier Transconductance (gm)
∆IC = ±10µA
Flyback Amplifier Source and Sink Current
VC = 0.6V
IFB = 50µA
BV
Output Switch Breakdown Voltage
VSAT
ILIM
∆IIN
∆ISW
f
V/V
3.0
6
9
0.8
0.6
0.9
1.08
1.25
V
V
0.4
0.45
0.54
V
15.0
14.0
16.3
17.6
18.0
V
V
4.5
V
mA
6.8
9
0.01
0.03
%/V
150
300
650
µmho
l
l
15
25
32
40
70
70
µA
µA
3V ≤ VIN ≤ VMAX, LT1170/LT1171/LT1172
ISW = 1.5mA
LT1170HV/LT1171HV/LT1172HV
LT1172S8
l
l
l
65
75
60
90
90
80
Output Switch “On” Resistance (Note 3)
LT1170
LT1171
LT1172
l
l
l
Control Voltage to Switch Current
Transconductance
LT1170
LT1171
LT1172
Switch Current Limit (LT1170)
Duty Cycle = 50%
Duty Cycle = 50%
Duty Cycle = 80% (Note 4)
TJ ≥ 25°C
TJ < 25°C
l
l
l
5
5
4
10
11
10
A
A
A
(LT1171)
Duty Cycle = 50%
Duty Cycle = 50%
Duty Cycle = 80% (Note 4)
TJ ≥ 25°C
TJ < 25°C
l
l
l
2.5
2.5
2.0
5.0
5.5
5.0
A
A
A
(LT1172)
Duty Cycle = 50%
Duty Cycle = 50%
Duty Cycle = 80% (Note 4)
TJ ≥ 25°C
TJ < 25°C
l
l
l
1.25
1.25
1.00
3.0
3.5
2.5
A
A
A
25
35
mA/A
100
112
115
kHz
kHz
Source
Sink
0.15
0.30
0.60
Supply Current Increase During Switch
On-Time
Switching Frequency
88
85
V
V
V
V
0.24
0.50
1.00
8
4
2
l
4
800
2.6
l
l
VFB
0.38
l
Minimum Input Voltage (Note 5)
IQ
3000
2400
4400
l
Ω
Ω
Ω
A/V
A/V
A/V
117012fi
For more information www.linear.com/LT1170
LT1170/LT1171/LT1172
Electrical
Characteristics
The
l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 15V, VC = 0.5V, VFB = VREF, output pin open, unless otherwise noted.
SYMBOL PARAMETER
DCMAX
CONDITIONS
MIN
Maximum Switch Duty Cycle
l
Shutdown Mode
Supply Current
3V ≤ VIN ≤ VMAX
VC = 0.05V
Shutdown Mode
Threshold Voltage
3V ≤ VIN ≤ VMAX
l
Flyback Sense Delay Time (Note 5)
100
50
(R ) I L + Vf
VIN (max, output shorted) = 15V +
( t) ( f)
buck and inverting mode
R = Inductor DC resistance
IL = 10A for LT1170, 5A for LT1171, and 2.5A for LT1172
Vf = Output catch diode forward voltage at IL
t = 0.6µs, f = 100kHz switching frequency
Maximum input voltage can be increased by increasing R or Vf.
External current limiting such as that shown in AN19, Figure 39, will
provide protection up to the full supply voltage rating. C1 in Figure 39
should be reduced to 200pF.
MAX
UNITS
92
97
%
100
250
µA
150
250
300
mV
mV
1.5
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Minimum effective switch “on” time for the LT1170/LT1171/
LT1172 (in current limit only) is ≈ 0.6µs. This limits the maximum safe
input voltage during an output shorted condition. Buck mode and inverting
mode input voltage during an output shorted condition is limited to:
( )
85
TYP
µs
Transformer designs will tolerate much higher input voltages because
leakage inductance limits rate of rise of current in the switch. These
designs must be evaluated individually to assure that current limit is well
controlled up to maximum input voltage.
Boost mode designs are never protected against output shorts because
the external catch diode and inductor connect input to output.
Note 3: Measured with VC in hi clamp, VFB = 0.8V. ISW = 4A for LT1170,
2A for LT1171, and 1A for LT1172.
Note 4: For duty cycles (DC) between 50% and 80%, minimum guaranteed
switch current is given by ILIM = 3.33 (2 – DC) for the LT1170, ILIM = 1.67
(2 – DC) for the LT1171, and ILIM = 0.833 (2 – DC) for the LT1172.
Note 5: Minimum input voltage for isolated flyback mode is 7V. VMAX = 55V
for HV grade in fully isolated mode to avoid switch breakdown.
117012fi
For more information www.linear.com/LT1170
5
LT1170/LT1171/LT1172
Typical Performance Characteristics
Switch Current Limit vs Duty Cycle*
Minimum Input Voltage
25°C
–55°C
8
125°C
4
* DIVIDE VERTICAL SCALE BY TWO FOR
LT1171, BY FOUR FOR LT1172.
0
1.6
SWITCH CURRENT = IMAX
2.8
2.7
2.6
SWITCH CURRENT = 0A
2.5
2.4
2.3
–75 –50 –25
10 20 30 40 50 60 70 80 90 100
DUTY CYCLE (%)
REFERENCE VOLTAGE (V)
0
TJ = –55°C
TJ = 25°C
–2
–3
–5
0
10
30
40
20
INPUT VOLTAGE (V)
60
50
700
1.246
1.244
1.242
1.240
1.238
1.234
–75 –50 –25
40
20
0
0
10
30
20
40
SUPPLY VOLTAGE (V)
50
60
1170/1/2 G07
6
400
300
200
0 25 50 75 100 125 150
TEMPERATURE (°C)
1170/1/2 G06
Supply Current vs Input Voltage*
TJ = 25°C
14
NOTE THAT THIS CURRENT DOES NOT
INCLUDE DRIVER CURRENT, WHICH IS
A FUNCTION OF LOAD CURRENT AND
DUTY CYCLE.
13
120
100
TJ = –55°C
80
60
TJ = ≥ 25°C
40
0
8
500
15
12
11
10
90% DUTY CYCLE
9
50% DUTY CYCLE
8
10% DUTY CYCLE
7
20
VC = 0V
7
600
Driver Current* vs Switch Current
DRIVER CURRENT (mA)
SUPPLY CURRENT (µA)
60
4
5
6
3
SWITCH CURRENT (A)*
0
–75 –50 –25
25 50 75 100 125 150
TEMPERATURE (°C)
0
140
VC = 50mV
80
2
1
1170/1/2 G05
TJ = 25°C
100
0
100
160
120
* DIVIDE CURRENT BY TWO FOR
LT1171, BY FOUR FOR LT1172.
0.2
1.248
Supply Current vs Supply Voltage
(Shutdown Mode)
140
0.4
800
1170/1/2 G04
160
0.6
1.250
1.236
–4
–55°C
Feedback Bias Current
vs Temperature
SUPPLY CURRENT (mA)
REFERENCE VOLTAGE CHANGE (mV)
4
1
25°C
0.8
1170/1/2 G03
FEEDBACK BIAS CURRENT (nA)
5
2
100°C
1.0
Reference Voltage vs Temperature
TJ = 150°C
150°C
1.2
1170/1/2 G02
Line Regulation
–1
1.4
0
0 25 50 75 100 125 150
TEMPERATURE (°C)
1170/1/2 G01
3
SWITCH SATURATION VOLTAGE (V)
MINIMUM INPUT VOLTAGE (V)
SWITCH CURRENT (A)
12
0
Switch Saturation Voltage
2.9
16
6
0
1
2
3
SWITCH CURRENT (A)
4
5
1170/1/2 G08
* AVERAGE LT1170 POWER SUPPLY CURRENT IS
FOUND BY MULTIPLYING DRIVER CURRENT BY
DUTY CYCLE, THEN ADDING QUIESCENT CURRENT.
For more information www.linear.com/LT1170
5
0% DUTY CYCLE
0
10
30
40
20
INPUT VOLTAGE (V)
50
60
1170/1/2 G09
* UNDER VERY LOW OUTPUT CURRENT CONDITIONS,
DUTY CYCLE FOR MOST CIRCUITS WILL APPROACH
10% OR LESS.
117012fi
LT1170/LT1171/LT1172
Typical Performance Characteristics
Error Amplifier Transconductance
4500
160
4000
140
TJ = 150°C
120
100
80
60
–55°C ≤ TJ ≤ 125°C
40
gm =
3000
2500
2000
1500
0
–75 –50 –25
10 20 30 40 50 60 70 80 90 100
VC PIN VOLTAGE (mV)
Idle Supply Current vs Temperature
5
4
3
25°C
250
150°C
200
150
200
100
0
0
–75 –50 –25
–50
0
25 50 75 100 125 150
TEMPERATURE (°C)
0
1170/1/2 G16
VSUPPLY
= 55V
0
10 20 30 40 50 60 70 80 90 100
SWITCH VOLTAGE (V)
Isolated Mode Flyback
Reference Voltage
23
22
FLYBACK VOLTAGE (V)
–100
VC VOLTAGE IS REDUCED UNTIL
REGULATOR CURRENT DROPS
BELOW 300µA
VSUPPLY
= 40V
1170/1/2 G15
2.0
1.8
TIME (µs)
VC PIN VOLTAGE (mV)
–150
100
50
0
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
FEEDBACK CURRENT (mA)
2.2
VC PIN CURRENT (µA)
–200
VOLTAGE
2.5
300
50
–350
–250
150
500 VSUPPLY
= 3V
400
VSUPPLY
= 15V
1170/1/2 G14
–300
200
600
100
–400
250
1.5
2.0
1.0
VC PIN VOLTAGE (V)
700
Flyback Blanking Time
300
0.5
800
–55°C
Shutdown Thresholds
CURRENT (OUT OF VC PIN)
0
Switch “Off” Characteristics
900
300
0 25 50 75 100 125 150
TEMPERATURE (°C)
400
VFB = 0.8V (CURRENT OUT OF VC PIN)
1170/1/2 G12
450
1170/1/2 G13
350
–400
1000
350
2
1
–75 –50 –25
0 25 50 75 100 125 150
TEMPERATURE (°C)
SWITCH CURRENT (µA)
8
VSUPPLY = 3V
–200
500
400
FEEDBACK VOLTAGE (mV)
IDLE SUPPLY CURRENT (mA)
9
VSUPPLY = 60V
TJ = 25°C
–100
Feedback Pin Clamp Voltage
VC = 0.6V
6
0
1170/1/2 G11
11
7
100
–300
500
0
VFB = 1.5V (CURRENT INTO VC PIN)
200
1000
1170/1/2 G10
10
∆I (VC PIN)
∆V (FB PIN)
3500
20
0
VC Pin Characteristics
300
VC PIN CURRENT (µA)
5000
180
TRANSCONDUCTANCE (µmho)
SUPPLY CURRENT (µA)
Shutdown Mode Supply Current
200
1.6
1.4
1.2
21
RFB = 500Ω
20
19
RFB = 1k
18
17
RFB = 10k
16
1.0
–75 –50 –25 0 25 50 75 100 125 150
JUNCTION TEMPERATURE (°C)
1170/1/2 G17
15
–75 –50 –25
0 25 50 75 100 125 150
TEMPERATURE (°C)
1170/1/2 G18
117012fi
For more information www.linear.com/LT1170
7
LT1170/LT1171/LT1172
Typical Performance Characteristics
Transconductance of Error
Amplifier
Normal/Flyback Mode Threshold on
Feedback Pin
–30
7000
30
5000
4000
60
gm
90
3000
120
2000
1000
150
0
180
–1000
210
10M
1k
10k
1M
100k
FREQUENCY (Hz)
–24
490
–22
480
–20
470
–18
FEEDBACK PIN VOLTAGE
(AT THRESHOLD)
460
–16
–14
450
–12
440
FEEDBACK PIN CURRENT
(AT THRESHOLD)
430
420
–10
–8
FEEDBACK PIN CURRENT (µA)
FEEDBACK PIN VOLTAGE (mV)
0
θ
PHASE (DEG)
TRANSCONDUCTANCE (µmho)
6000
500
–6
410
400
–50 –25
0
–4
25 50 75 100 125 150
TEMPERATURE (°C)
1170/1/2 G19
1170/1/2 G20
Block Diagram
VIN
SWITCH
OUT
16V
2.3V
REG
FLYBACK
ERROR
AMP
LT1172
5A, 75V
SWITCH
100kHz
OSC
LOGIC
DRIVER
ANTISAT
MODE
SELECT
COMP
–
FB
ERROR
AMP
VC
+
+
SHUTDOWN
CIRCUIT
1.24V
REF
CURRENT
AMP
GAIN ≈ 6
–
0.02Ω
(0.04Ω LT1171)
(0.16Ω LT1172)
0.16Ω
0.15V
(LT1170 AND LT1171 ONLY)
E1†
† ALWAYS CONNECT E1 TO THE GROUND PIN ON MINIDIP, 8- AND 16-PIN SURFACE MOUNT PACKAGES.
E1 AND E2 INTERNALLY TIED TO GROUND ON TO-3 AND TO-220 PACKAGES.
8
E2
1170/1/2 BD
117012fi
For more information www.linear.com/LT1170
LT1170/LT1171/LT1172
Operation
The LT1170/LT1171/LT1172 are current mode switchers.
This means that switch duty cycle is directly controlled by
switch current rather than by output voltage. Referring to
the block diagram, the switch is turned “on” at the start of
each oscillator cycle. It is turned “off” when switch current
reaches a predetermined level. Control of output voltage
is obtained by using the output of a voltage sensing error amplifier to set current trip level. This technique has
several advantages. First, it has immediate response to
input voltage variations, unlike ordinary switchers which
have notoriously poor line transient response. Second,
it reduces the 90° phase shift at midfrequencies in the
energy storage inductor. This greatly simplifies closed
loop frequency compensation under widely varying input
voltage or output load conditions. Finally, it allows simple
pulse-by-pulse current limiting to provide maximum switch
protection under output overload or short conditions. A
low dropout internal regulator provides a 2.3V supply for
all internal circuitry on the LT1170/LT1171/LT1172. This
low dropout design allows input voltage to vary from 3V
to 60V with virtually no change in device performance. A
100kHz oscillator is the basic clock for all internal timing.
It turns “on” the output switch via the logic and driver
circuitry. Special adaptive anti-sat circuitry detects onset
of saturation in the power switch and adjusts driver current
instantaneously to limit switch saturation. This minimizes
driver dissipation and provides very rapid turnoff of the
switch.
A 1.2V bandgap reference biases the positive input of the
error amplifier. The negative input is brought out for output
voltage sensing. This feedback pin has a second function;
when pulled low with an external resistor, it programs the
LT1170/LT1171/LT1172 to disconnect the main error amplifier output and connects the output of the flyback amplifier
to the comparator input. The LT1170/LT1171/LT1172 will
then regulate the value of the flyback pulse with respect
to the supply voltage.* This flyback pulse is directly proportional to output voltage in the traditional transformer
coupled flyback topology regulator. By regulating the
amplitude of the flyback pulse, the output voltage can be
regulated with no direct connection between input and
output. The output is fully floating up to the breakdown
voltage of the transformer windings. Multiple floating
outputs are easily obtained with additional windings.
A special delay network inside the LT1170/ LT1171/LT1172
ignores the leakage inductance spike at the leading edge
of the flyback pulse to improve output regulation.
The error signal developed at the comparator input is
brought out externally. This pin (VC) has four different functions. It is used for frequency compensation, current limit
adjustment, soft-starting, and total regulator shutdown.
During normal regulator operation this pin sits at a voltage
between 0.9V (low output current) and 2.0V (high output
current). The error amplifiers are current output (gm) types,
so this voltage can be externally clamped for adjusting
current limit. Likewise, a capacitor coupled external clamp
will provide soft-start. Switch duty cycle goes to zero if
the VC pin is pulled to ground through a diode, placing the
LT1170/LT1171/LT1172 in an idle mode. Pulling the VC pin
below 0.15V causes total regulator shutdown, with only
50µA supply current for shutdown circuitry biasing. See
Application Note 19 for full application details.
Extra Pins on the MiniDIP and Surface Mount
Packages
The 8- and 16-pin versions of the LT1172 have the emitters
of the power transistor brought out separately from the
ground pin. This eliminates errors due to ground pin voltage
drops and allows the user to reduce switch current limit
2:1 by leaving the second emitter (E2) disconnected. The
first emitter (E1) should always be connected to the ground
pin. Note that switch “on” resistance doubles when E2 is
left open, so efficiency will suffer somewhat when switch
currents exceed 300mA. Also, note that chip dissipation
will actually increase with E2 open during normal load
operation, even though dissipation in current limit mode
will decrease. See “Thermal Considerations” next.
Thermal Considerations When Using the MiniDIP and
SW Packages
The low supply current and high switch efficiency of the
LT1172 allow it to be used without a heat sink in most
applications when the TO-220 or TO-3 package is selected. These packages are rated at 50°C/W and 35°C/W
respectively. The miniDIPs, however, are rated at 100°C/W
in ceramic (J) and 130°C/W in plastic (N).
*See note under Block Diagram.
117012fi
For more information www.linear.com/LT1170
9
LT1170/LT1171/LT1172
Operation
Care should be taken for miniDIP applications to ensure that
the worst case input voltage and load current conditions
do not cause excessive die temperatures. The following
formulas can be used as a rough guide to calculate LT1172
power dissipation. For more details, the reader is referred
to Application Note 19 (AN19), “Efficiency Calculations”
section.
Average supply current (including driver current) is:
IIN ≈ 6mA + ISW (0.004 + DC/40)
ISW = switch current
DC = switch duty cycle
Switch power dissipation is given by:
PSW = (ISW)2 • (RSW)(DC)
RSW = LT1172 switch “on” resistance (1Ω maximum)
Total power dissipation is the sum of supply current times
input voltage plus switch power:
PD(TOT) = (IIN)(VIN) + PSW
In a typical example, using a boost converter to generate
12V at 0.12A from a 5V input, duty cycle is approximately
60%, and switch current is about 0.65A, yielding:
IIN = 6mA + 0.65(0.004 + DC/40) = 18mA
PSW = (0.65)2 • (1Ω)(0.6) = 0.25W
PD(TOT) = (5V)(0.018A) + 0.25 = 0.34W
Temperature rise in a plastic miniDIP would be 130°C/W
times 0.34W, or approximately 44°C. The maximum ambient temperature would be limited to 100°C (commercial
temperature limit) minus 44°C, or 56°C.
In most applications, full load current is used to calculate
die temperature. However, if overload conditions must
also be accounted for, four approaches are possible. First,
if loss of regulated output is acceptable under overload
conditions, the internal thermal limit of the LT1172 will
protect the die in most applications by shutting off switch
current. Thermal limit is not a tested parameter, however,
and should be considered only for noncritical applications
with temporary overloads. A second approach is to use the
10
larger TO-220 (T) or TO-3 (K) package which, even without
a heat sink, may limit die temperatures to safe levels under
overload conditions. In critical situations, heat sinking of
these packages is required; especially if overload conditions
must be tolerated for extended periods of time.
The third approach for lower current applications is to
leave the second switch emitter (miniDIP only) open. This
increases switch “on” resistance by 2:1, but reduces switch
current limit by 2:1 also, resulting in a net 2:1 reduction in
I2R switch dissipation under current limit conditions.
The fourth approach is to clamp the VC pin to a voltage
less than its internal clamp level of 2V. The LT1172 switch
current limit is zero at approximately 1V on the VC pin
and 2A at 2V on the VC pin. Peak switch current can be
externally clamped between these two levels with a diode.
See AN19 for details.
LT1170/LT1171/LT1172 Synchronizing
The LT1170/LT1171/LT1172 can be externally synchronized in the frequency range of 120kHz to 160kHz. This
is accomplished as shown in the accompanying figures.
Synchronizing occurs when the VC pin is pulled to ground
with an external transistor. To avoid disturbing the DC
characteristics of the internal error amplifier, the width of
the synchronizing pulse should be under 0.3µs. C2 sets
the pulse width at ≅ 0.2µs. The effect of a synchronizing
pulse on the LT1170/LT1171/LT1172 amplifier offset can
be calculated from:
ΔVOS
VC ⎞
⎛ KT ⎞
⎛
⎜⎝ q ⎟⎠ ( tS ) ( fS ) ⎜⎝I C + R3 ⎟⎠
=
IC
KT
= 26mV at 25°C
q
tC = pulse width
fS = pulse frequency
IC = VC source current (≈200µA)
VC = operating VC voltage (1V to 2V)
R3 = resistor used to set mid-frequency “zero” in
frequency compensation network.
117012fi
For more information www.linear.com/LT1170
LT1170/LT1171/LT1172
Operation
With tS = 0.2µs, fS = 150kHz, VC = 1.5V, and R3 = 2k, offset
voltage shift is ≈ 3.8mV. This is not particularly bothersome, but note that high offsets could result if R3 were
reduced to a much lower value. Also, the synchronizing
transistor must sink higher currents with low values of
R3, so larger drives may have to be used. The transistor
must be capable of pulling the VC pin to within 200mV of
ground to ensure synchronizing.
Synchronizing with Bipolar Transistor
Synchronizing with MOS Transistor
VIN
VIN
LT1170
LT1170
VC
GND
VC
GND
R3
C2
39pF
2N2369
C1
R1
3k
R2
2.2k
D1
1N4158
R3
VN2222*
C1
FROM 5V
LOGIC
C2
100pF
R2
2.2k
D2
1N4158
* SILICONIX OR EQUIVALENT
1170/1/2 OP01
FROM 5V
LOGIC
1170/1/2 OP02
Typical Applications
Flyback Converter
L2 OPTIONAL
FILTER
5µH
C4
100µF
N* = 1/3
VIN
20V TO 30V
D3
25V
1W
D2
MUR110
VIN
C4*
100µF
VSW
+
1 N*
VIN
D1
VOUT
5V
6A
+
CLAMP TURN-ON
SPIKE
VSNUB
a
b
0V
VOUT + Vf
c
C1
2000µF
0V
R1
3.74k
N • VIN
d
∆I
PRIMARY CURRENT
IPRI/N
FB
GND
VC
SECONDARY CURRENT
0
R3
1.5k
C2
0.15µF
*REQUIRED IF INPUT LEADS ≥ 2"
R2
1.24k
0
0
SECONDARY VOLTAGE
AREA “c” = AREA “d” TO MAINTAIN
ZERO DC VOLTS ACROSS SECONDARY
IPRI
0
LT1170
V
+ Vf
PRIMARY FLYBACK VOLTAGE = OUT
N
LT1170 SWITCH VOLTAGE
AREA “a” = AREA “b” TO MAINTAIN
ZERO DC VOLTS ACROSS PRIMARY
IPRI
LT1170 SWITCH CURRENT
IPRI
SNUBBER DIODE CURRENT
(I )(L )
t = PRI L
VSNUB
1170/1/2 TA03
117012fi
For more information www.linear.com/LT1170
11
LT1170/LT1171/LT1172
Typical Applications
(Note that maximum output currents are divided by 2 for LT1171, by 4 for LT1172.)
LCD Contrast Supply
5V*
L1**
50µH
VIN
VSW
LT1172
E1
GND
VC
R2
100k
FB
R1
200k
C1
1µF
TANTALUM
VOUT
–10V TO –26V
D2
C4
0.047µF
VN2222
+
D1
1N914
R3
15k
C3
0.0047µF
D3
+
E2
OPTIONAL
SHUTDOWN
VBAT*
3V TO 20V
C2***
2µF
TANTALUM
D2, D3 = ER82.004 600mA SCHOTTKY. OTHER FAST SWITCHING TYPES MAY BE USED.
* VIN AND BATTERY MAY BE TIED TOGETHER. MAXIMUM VALUE FOR VBAT IS EQUAL TO THE |NEGATIVE OUTPUT| + 1V. WITH HIGHER
BATTERY VOLTAGES, HIGHEST EFFICIENCY IS OBTAINED BY RUNNING THE LT1172 VIN PIN FROM 5V. SHUTTING OFF THE 5V SUPPLY
WILL AUTOMATICALLY TURN OFF THE LT1172. EFFICIENCY IS ABOUT 80% AT IOUT = 25mA.
R1, R2, R3 ARE MADE LARGE TO MINIMIZE BATTERY DRAIN IN SHUTDOWN, WHICH IS APPROXIMATELY VBAT /(R1 + R2 + R3).
** FOR HIGH EFFICIENCY, L1 SHOULD BE MADE ON A FERRITE OR MOLYPERMALLOY CORE. PEAK INDUCTOR CURRENTS ARE ABOUT
600mA AT POUT = 0.7Ω. INDUCTOR SERIES RESISTANCE SHOULD BE LESS THAN 0.4Ω FOR HIGH EFFICIENCY.
*** OUTPUT RIPPLE IS ABOUT 200mVP-P TO 400mVP-P WITH C2 = 2µF TANTALUM. IF LOWER RIPPLE IS DESIRED, INCREASE C2, OR ADD
A 10Ω, 1µF TANTALUM OUTPUT FILTER.
1170/1/2 TA04
Driving High Voltage FET
(for Off-Line Applications, See AN25)
G
VIN
10V TO
20V
+
External Current Limit
VX
D
Q1
D1
LT1170
R2
VSW
≈ 2V
R1
500Ω
LT1170
D1
GND
VC
GND
1170/1/2 TA06
1170/1/2 TA05
12
117012fi
For more information www.linear.com/LT1170
LT1170/LT1171/LT1172
Typical Applications
(Note that maximum output currents are divided by 2 for LT1171, by 4 for LT1172.)
Negative-to-Positive Buck-Boost Converter†
External Current Limit
L1**
50µH
L2
OPTIONAL
OUTPUT
FILTER
D1
VIN
C4*
100µF
OPTIONAL
INPUT FILTER
+
VSW
+
R1
11.3k
C2
1000µF
LT1170
VIN
C3
LT1170
+
VOUT
12V
2A
–
VIN
FB
VC
L3
R3
2.2k
C1
0.22µF
VIN
–20V
Q1
R2
1.24k
VC
GND
R1
1k
Q1
GND
VSW
FB
R2
C1
1000pF
C2
RS
NOTE THAT THE LT1170
GND PIN IS NO LONGER
COMMON TO VIN–.
* REQUIRED IF INPUT LEADS ≥ 2"
** PULSE ENGINEERING 92114, COILTRONICS 50-2-52
† THIS CIRCUIT IS OFTEN USED TO CONVERT –48V TO 5V. TO GUARANTEE
FULL SHORT-CIRCUIT PROTECTION, THE CURRENT LIMIT CIRCUIT SHOWN
IN AN19, FIGURE 39, SHOULD BE ADDED WITH C1 REDUCED TO 200pF.
1170/1/2 TA08
1170/1/2 TA07
Negative Buck Converter
+
D1
* REQUIRED IF INPUT LEADS ≥ 2"
** PULSE ENGINEERING 92114
COILTRONICS 50-2-52
VIN
C3*
100µF
OPTIONAL
INPUT FILTER
L3
L1**
50µH
VSW
+
Q1
2N3906
LT1170
GND
VC
LOAD
R1
4.64k
R4
12k
FB
OPTIONAL
OUTPUT
FILTER
C1
R3
VIN
–20V
C2
1000µF
–5.2V
4.5A
+
C4
200µF
R2
1.24k
1170/1/2 TA09
117012fi
For more information www.linear.com/LT1170
13
LT1170/LT1171/LT1172
Typical Applications
Positive-to-Negative Buck-Boost Converter
D3†
1N4001
R5†
470Ω, 1W
+
VIN
C4
1µF
+
VSW
LT1170
R3
5k
C2
0.1µF
+
R2
1.24k
* REQUIRED IF INPUT LEADS ≥ 2"
** PULSE ENGINEERING 92114, COILTRONICS 50-2-52
† TO AVOID STARTUP PROBLEMS FOR INPUT VOLTAGES
BELOW 10V, CONNECT ANODE OF D3 TO VIN, AND
REMOVE R5. C1 MAY BE REDUCED FOR LOWER OUTPUT
CURRENTS. C1 ≈ (500µF)(IOUT).
FOR 5V OUTPUTS, REDUCE R3 TO 1.5k, INCREASE C2 TO
0.3µF, AND REDUCE R6 TO 100Ω.
C5
100µF*
D2
1N914
R1
10.7k
FB
VC
GND
VIN
10V TO
30V
R4
47Ω
+
C3
2µF
C1†
1000µF
R6
470Ω
D1
VOUT
–12V
2A
L1**
50µH
1170/1/2 TA10
High Efficiency Constant Current Charger
INPUT VOLTAGE
> VBAT + 2V < 35V
R3
25k
VSW
D1
1N5819
LT1171
VIN
C1
200µF
35V
C2
2.2µF
35V
TANTALUM
+
RUN = 0V
SHUTDOWN = 5V
R2
1k
VC
GND
+
V+
+
C3
0.47µF
V–
C4
0.01µF
R4
1k
R5
0.05Ω
L2*
10µH, 1A
+
D2
MBR340
R8
1k
R7
22k
+
L1
100µH, 1A
2N3904
R6
78k
* L2 REDUCES RIPPLE CURRENT INTO
THE BATTERY BY ABOUT 20:1.
IT MAY BE OMITTED IF DESIRED.
–
LT1006
FB
1.244V • R4
= 1A AS SHOWN
R3 • R5
ICHRG =
C4
200µF
25V
1A
+
BATTERY
2V TO 25V
1170/1/2 TA11
Backlight CCFL Supply (see AN45 for details)
INPUT VOLTAGE†
4.5V TO 20V
L2***
1k
L1**
300µH
1N5818
A
33pF
3kV
LAMP
Q1*
10µF
TANT
+
V IN
E2
VSW
0.02µF
LT1172
Q2*
B
E1 GND
VC
+
2µF
14
FB
C6
1µF
D1
1N914
R3
10k
D2
1N914
50k
INTENSITY
ADJUST
R1
560Ω
* Q1,Q2 = BCP56 OR MPS650/561
1170/1/2 TA12
** COILTRONICS CTX300-4
*** SUMIDA 6345-020 OR COILTRONICS 110092-1
† A MODIFICATION WILL ALLOW OPERATION DOWN TO 4.5V. CONSULT FACTORY.
117012fi
For more information www.linear.com/LT1170
LT1170/LT1171/LT1172
Typical Applications
Positive Buck Converter
VIN
* REQUIRED IF INPUT LEADS ≥ 2"
** PULSE ENGINEERING 92114
COILTRONICS 50-2-52
D3
C3
2.2µF
+
VIN
+
L2
4µH
VSW
LT1170
C5*
100µF
FB
VC
GND
R3
470Ω
C1
1µF
D2
1N914
R1
3.74k
+
R2
1.24k
OPTIONAL
OUTPUT
FILTER
C2
1µF
R4
10Ω
L1**
50µH
r
C4
1000µF
D1
C5
200µF
+
5V, 4.5A
100mA
MINIMUM
1170/1/2 TA13
Negative Boost Regulator
D2
VSW
VIN
R1
27k
LT1170
C4*
470µF
VIN
–15V
+
GND
L1
50µH
VC
+
+
C3
10µF
C1
1000µF
RO
(MINIMUM
LOAD)
FB
R3
3.3k
C2
0.22µF
R2
1.24k
D1
VOUT
–28V, 1A
1170/1/2 TA14
* REQUIRED IF INPUT LEADS ≥ 2"
Driving High Voltage NPN
C1
D2
R2**
R1*
Q1
D1
VIN
VSW
LT1170
GND
* SETS IB (ON)
** SETS IB (OFF)
1170/1/2 TA15
117012fi
For more information www.linear.com/LT1170
15
LT1170/LT1171/LT1172
Typical Applications
Forward Converter
L1
25µH
D1
T1
C2
R4
1
M
N
D2
C1
2000µF
VOUT
5V, 6A
+
R1
3.74k
D3
VIN
VSW
VIN
20V TO 30V
D4
LT1170
FB
R6
330Ω
VC
GND
Q1
R3
R2
1.24k
R5
1Ω
C4
C3
1170/1/2 TA16
High Efficiency 5V Buck Converter
VIN
+
VSW
C1
330µF
35V
FB
LT1170
VC
10µH
3A
VIN
GND
C6
0.02µF
R1
680Ω
C5
0.03µF
C4
0.1µF
D1
MBR330p
2.5V = SHUTDOWN
OPEN = BURST MODE
DIODE
LT1432
+
OPTIONAL
OUTPUT
FILTER
+
L1
50µH
R2*
0.013Ω
+
VC
VIN
MODE LOGIC
220pF
C3
4.7µF
TANT
100µF
16V
D2
1N4148
V+
×
C2
390µF
16V
VOUT
5V
3A**
VLIM
VOUT
MODE
GND
* R2 IS MADE FROM PC BOARD
COPPER TRACES.
** MAXIMUM CURRENT IS DETERMINED
BY THE CHOICE OF LT1070 FAMILY.
SEE APPLICATION SECTION.
1170/1/2 TA17
16
117012fi
For more information www.linear.com/LT1170
LT1170/LT1171/LT1172
Package Description
Please refer to http://www.linear.com/product/LT1170#packaging for the most recent package drawings.
J8 Package
8-Lead CERDIP (Narrow .300 Inch, Hermetic)
(Reference LTC DWG # 05-08-1110)
CORNER LEADS OPTION
(4 PLCS)
.005
(0.127)
MIN
.023 – .045
(0.584 – 1.143)
HALF LEAD
OPTION
.405
(10.287)
MAX
8
7
6
5
.025
(0.635)
RAD TYP
.045 – .068
(1.143 – 1.650)
FULL LEAD
OPTION
.220 – .310
(5.588 – 7.874)
1
.300 BSC
(7.62 BSC)
2
3
4
.200
(5.080)
MAX
.015 – .060
(0.381 – 1.524)
.008 – .018
(0.203 – 0.457)
0 – 15
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE
OR TIN PLATE LEADS
.045 – .065
(1.143 – 1.651)
.014 – .026
(0.360 – 0.660)
.100
(2.54)
BSC
.125
3.175
MIN
J8 0801
K Package
4-Lead TO-3 Metal Can
(Reference LTC DWG # 05-08-1311)
1.177 – 1.197
(29.90 – 30.40)
.320 – .350
(8.13 – 8.89)
.760 – .775
(19.30 – 19.69)
.470 TP
P.C.D.
.060 – .135
(1.524 – 3.429)
.655 – .675
(16.64 – 19.05)
.151 – .161
(3.84 – 4.09)
DIA 2 PLC
.167 – .177
(4.24 – 4.49)
R
.420 – .480
(10.67 – 12.19)
.038 – .043
(0.965 – 1.09)
72°
18°
.490 – .510
(12.45 – 12.95)
R
K4(TO-3) 0801
(OBSOLETE PACKAGE)
117012fi
For more information www.linear.com/LT1170
17
LT1170/LT1171/LT1172
Package Description
Please refer to http://www.linear.com/product/LT1170#packaging for the most recent package drawings.
N Package
8-Lead PDIP (Narrow .300 Inch)
(Reference LTC DWG # 05-08-1510 Rev I)
.400*
(10.160)
MAX
8
7
6
5
1
2
3
4
.255 ±.015*
(6.477 ±0.381)
.300 – .325
(7.620 – 8.255)
.008 – .015
(0.203 – 0.381)
(
+.035
.325 –.015
8.255
+0.889
–0.381
)
.045 – .065
(1.143 – 1.651)
.065
(1.651)
TYP
.100
(2.54)
BSC
.130 ±.005
(3.302 ±0.127)
.120
(3.048) .020
MIN
(0.508)
MIN
.018 ±.003
N8 REV I 0711
(0.457 ±0.076)
NOTE:
1. DIMENSIONS ARE
INCHES
MILLIMETERS
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm)
18
117012fi
For more information www.linear.com/LT1170
LT1170/LT1171/LT1172
Package Description
Please refer to http://www.linear.com/product/LT1170#packaging for the most recent package drawings.
Q Package
5-Lead Plastic DD Pak
(Reference LTC DWG # 05-08-1461 Rev F)
.256
(6.502)
.060
(1.524)
TYP
.060
(1.524)
.390 – .415
(9.906 – 10.541)
.165 – .180
(4.191 – 4.572)
.045 – .055
(1.143 – 1.397)
15° TYP
.060
(1.524)
.183
(4.648)
+.008
.004 –.004
+0.203
0.102 –0.102
.059
(1.499)
TYP
.330 – .370
(8.382 – 9.398)
(
)
.095 – .115
(2.413 – 2.921)
.075
(1.905)
DETAIL A
.300
(7.620)
+.012
.143 –.020
+0.305
3.632 –0.508
(
BOTTOM VIEW OF DD PAK
HATCHED AREA IS SOLDER PLATED
COPPER HEAT SINK
.067
(1.702)
.028 – .038 BSC
(0.711 – 0.965)
TYP
)
.013 – .023
(0.330 – 0.584)
.050 ±.012
(1.270 ±0.305)
DETAIL A
0° – 7° TYP
.420
.276
.080
.420
0° – 7° TYP
.325
.350
.205
.585
.585
.320
.090
.090
.067
.042
RECOMMENDED SOLDER PAD LAYOUT
NOTE:
1. DIMENSIONS IN INCH/(MILLIMETER)
2. DRAWING NOT TO SCALE
.067
.042
RECOMMENDED SOLDER PAD LAYOUT
FOR THICKER SOLDER PASTE APPLICATIONS
Q(DD5) 0811 REV F
117012fi
For more information www.linear.com/LT1170
19
LT1170/LT1171/LT1172
Package Description
Please refer to http://www.linear.com/product/LT1170#packaging for the most recent package drawings.
S8 Package
8-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610 Rev G)
.189 – .197
(4.801 – 5.004)
NOTE 3
.045 ±.005
.050 BSC
8
.245
MIN
.160 ±.005
.010 – .020
× 45°
(0.254 – 0.508)
NOTE:
1. DIMENSIONS IN
.053 – .069
(1.346 – 1.752)
0°– 8° TYP
.014 – .019
(0.355 – 0.483)
TYP
INCHES
(MILLIMETERS)
2. DRAWING NOT TO SCALE
3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
4. PIN 1 CAN BE BEVEL EDGE OR A DIMPLE
20
5
.150 – .157
(3.810 – 3.988)
NOTE 3
1
RECOMMENDED SOLDER PAD LAYOUT
.016 – .050
(0.406 – 1.270)
6
.228 – .244
(5.791 – 6.197)
.030 ±.005
TYP
.008 – .010
(0.203 – 0.254)
7
2
3
4
.004 – .010
(0.101 – 0.254)
.050
(1.270)
BSC
SO8 REV G 0212
117012fi
For more information www.linear.com/LT1170
LT1170/LT1171/LT1172
Package Description
Please refer to http://www.linear.com/product/LT1170#packaging for the most recent package drawings.
SW Package
16-Lead Plastic Small Outline (Wide .300 Inch)
(Reference LTC DWG # 05-08-1620)
.050 BSC .045 .005
.030 .005
TYP
.398 – .413
(10.109 – 10.490)
NOTE 4
16
N
15
14
13
12
11
10
9
N
.325 .005
.420
MIN
.394 – .419
(10.007 – 10.643)
NOTE 3
1
2
3
N/2
N/2
RECOMMENDED SOLDER PAD LAYOUT
1
.005
(0.127)
RAD MIN
.009 – .013
(0.229 – 0.330)
NOTE:
1. DIMENSIONS IN
.291 – .299
(7.391 – 7.595)
NOTE 4
.010 – .029 × 45°
(0.254 – 0.737)
2
3
4
5
6
.093 – .104
(2.362 – 2.642)
7
8
.037 – .045
(0.940 – 1.143)
0 – 8 TYP
NOTE 3
.016 – .050
(0.406 – 1.270)
.050
(1.270)
BSC
.014 – .019
(0.356 – 0.482)
TYP
INCHES
(MILLIMETERS)
2. DRAWING NOT TO SCALE
3. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS.
THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS
4. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
.004 – .012
(0.102 – 0.305)
S16 (WIDE) 0502
117012fi
For more information www.linear.com/LT1170
21
LT1170/LT1171/LT1172
Package Description
Please refer to http://www.linear.com/product/LT1170#packaging for the most recent package drawings.
T Package
5-Lead Plastic TO-220 (Standard)
(Reference LTC DWG # 05-08-1421)
.390 – .415
(9.906 – 10.541)
.165 – .180
(4.191 – 4.572)
.147 – .155
(3.734 – 3.937)
DIA
.045 – .055
(1.143 – 1.397)
.230 – .270
(5.842 – 6.858)
.460 – .500
(11.684 – 12.700)
.570 – .620
(14.478 – 15.748)
.330 – .370
(8.382 – 9.398)
.700 – .728
(17.78 – 18.491)
.620
(15.75)
TYP
SEATING PLANE
.152 – .202
.260 – .320 (3.861 – 5.131)
(6.60 – 8.13)
BSC
.067
(1.70)
.095 – .115
(2.413 – 2.921)
.155 – .195*
(3.937 – 4.953)
.013 – .023
(0.330 – 0.584)
.028 – .038
(0.711 – 0.965)
.135 – .165
(3.429 – 4.191)
* MEASURED AT THE SEATING PLANE
T5 (TO-220) 0801
22
117012fi
For more information www.linear.com/LT1170
LT1170/LT1171/LT1172
Revision History
(Revision history begins at Rev G)
REV
DATE
DESCRIPTION
PAGE NUMBER
G
3/10
Updated to Reactivate LT1172M from Obsoleted Parts List
2
H
6/16
Removed #PBF from MJ8 part number in first line
3
I
3/17
Corrected Flyback Amplifier Source and Sink Current units to µA from mA
Obsoleted LT1172M and LT1172MJ8
4
2, 3
117012fi
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representaFor more
information
www.linear.com/LT1170
tion that the interconnection
of its circuits
as described
herein will not infringe on existing patent rights.
23
LT1170/LT1171/LT1172
Typical Application
Positive Current Boosted Buck Converter
VIN
28V
470Ω
2W
C3
0.47µF
C6
0.002µF
D2
VIN
R6
470Ω
1: N
VSW
LT1170
FB
+
7
R3
680Ω
N ≈ 0.25
D1
VIN
VC
GND
C5*
100µF
R2
1.24k
R7
1k
C4
0.01µF
6
–
2
+
3
LM308
C1
0.33µF
4
8
200pF
R5
5k
R4
1.24k
R1
5k
+
* REQUIRED IF INPUT LEADS ≥ 2"
VOUT
5V, 10A
C2
5000µF
1170/1/2 TA18
Related Parts
PART NUMBER
DESCRIPTION
COMMENTS
LT1070/LT1071/LT1072 5A/2.5A/1.25A High Efficiency Switching Regulators
40kHz, VIN to 60V, VSW to 75V
LT1074/LT1076
5.5A/2A Step-Down Switching Regulators
100kHz, Also for Positive-to-Negative Conversion
LT1082
1A, High Voltage, High Efficiency Switching Regulator
VIN to 75V, VSW to 100V, Telecom
LT1268/LT1268B
7.5A, 150kHz Switching Regulators
VIN to 30V, VSW to 60V
LT1269/LT1271
4A High Efficiency Switching Regulators
100kHz/60kHz, VIN to 30V, VSW to 60V
LT1270/LT1270A
8A and 10A High Efficiency Switching Regulators
60kHz, VIN to 30V, VSW to 60V
LT1370
500kHz High Efficiency 6A Switching Regulator
High Power Boost, Flyback, SEPIC
LT1371
500kHz High Efficiency 3A Switching Regulator
Good for Boost, Flyback, Inverting, SEPIC
LT1372/LT1377
500kHz and 1MHz High Efficiency 1.5A Switching Regulators
Directly Regulates ±VOUT
LT1373
250kHz Low Supply Current High Efficiency 1.5A Switching Regulator
Low 1mA Quiescent Current
LT1374
4A, 500kHz Step-Down Switching Regulator
Synchronizable, VIN to 25V
LT1375/LT1376
1.5A, 500kHz Step-Down Switching Regulators
Up to 1.25A Out from an SO-8
LT1425
Isolated Flyback Switching Regulator
6W Output, ±5% Regulation, No Optocoupler Needed
LT1507
500kHz Monolithic Buck Mode Switching Regulator
1.5A Switch, Good for 5V to 3.3V
LT1533
Ultralow Noise 1A Switching Regulator
Push-Pull,
工商网监
湘ICP备2023018690号
