0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
LTC3731CUH#TRPBF

LTC3731CUH#TRPBF

  • 厂商:

    AD(亚德诺)

  • 封装:

    QFN-32_5X5MM-EP

  • 描述:

    IC REG CTRLR BUCK 32QFN

  • 数据手册
  • 价格&库存
LTC3731CUH#TRPBF 数据手册
LTC3731 3-Phase, 600kHz, Synchronous Buck Switching Regulator Controller DESCRIPTION FEATURES 3-Phase Current Mode Controller with Onboard MOSFET Drivers n ±5% Output Current Matching Optimizes Thermal Performance and Size of Inductors and MOSFETs n Differential Amplifier Accurately Senses V OUT n ±1% V Accuracy Over Temperature REF n V OUT Range: 0.6V to 5.5V without Diffamp n V OUT Range: 0.6V to (VCC – 1.2V) with Diffamp n 250kHz to 600kHz Per Phase, PLL, Fixed Frequency n PWM, Stage Shedding™ or Burst Mode® Operation n OPTI-LOOP® Compensation Minimizes C OUT n Adjustable Soft-Start Current Ramping n Short-Circuit Shutdown Timer with Defeat Option n Overvoltage Soft Latch n Adjustable Undervoltage Lockout Threshold n Selectable Phase Output for Up to 12-Phase Operation n Available in 5mm × 5mm QFN and 36-Pin Narrow (0.209") SSOP Packages The LTC®3731 is a PolyPhase® synchronous step-down switching regulator controller that drives all N-channel external power MOSFET stages in a phase-lockable fixed frequency architecture. The 3-phase controller drives its output stages with 120° phase separation at frequencies of up to 600kHz per phase to minimize the RMS current losses in both the input and output filter capacitors. The 3‑phase technique effectively triples the fundamental frequency, improving transient response while operating each controller at an optimal frequency for efficiency and ease of thermal design. Light load efficiency is optimized by using a choice of output Stage Shedding or Burst Mode operation. n A differential amplifier provides true remote sensing of both the high and low side of the output voltage at the point of load. Soft-start and a defeatable, timed short-circuit shutdown protect the MOSFETs and the load. Current foldback provides protection for the external MOSFETs under short-circuit or overload conditions. APPLICATIONS L, LT, LTC, LTM, Bust Mode, OPTI-LOOP, PolyPhase, Linear Technology and the Linear logo are registered and Stage Shedding is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents, including 5481178, 5929620, 6177787, 6144194, 6100678, 5408150, 6580258, 6462525, 630466, 5705919. Desktop Computers and Servers n High Performance Notebook Computers n High Output Current DC/DC Power Supplies n TYPICAL APPLICATION VCC 4.5V TO 7V VCC 10µF LTC3731 BOOST1 BOOST2 BOOST3 0.1µF SW3 SW2 SW1 PGOOD PLLIN POWER GOOD INDICATOR OPTIONAL SYNC IN PLLFLTR VIN TG1 0.8µH 0.003Ω 0.8µH 0.003Ω 0.8µH 0.003Ω SW1 + VIN 5V TO 28V 22µF 35V BG1 SENSE1+ SENSE1– TG2 VIN SW2 VOUT 1.35V 55A BG2 PGND 36k UVADJ 12k 680pF 5k 0.01µF 7.5k 6.04k 100pF SENSE2+ SENSE2– ITH TG3 RUN/SS SW3 SGND EAIN DIFFOUT IN – IN + VIN BG3 SENSE3+ SENSE3– + COUT 470µF 4V 3731 F01 Figure 1. High Current Triple Phase Step-Down Converter 3731fc 1 LTC3731 ABSOLUTE MAXIMUM RATINGS (Note 1) Topside Driver Voltages (BOOSTn).............. 38V to –0.3V Switch Voltage (SWn).................................... 32V to –5V Boosted Driver Voltage (BOOSTn – SWn)..... 7V to –0.3V Peak Output Current < 1ms (TGn, BGn).......................5A Supply Voltages (VCC, VDR), PGOOD Pin Voltage.................................................... 7V to –0.3V RUN/SS, PLLFLTR, PLLIN, UVADJ, FCB Voltages ...............................................VCC to –0.3V SENSE+, SENSE– Voltages........................ 5.5V to –0.3V ITH Voltage ................................................ 2.4V to –0.3V Operating Ambient Temperature Range LTC3731C................................................. 0°C to 70°C LTC3731I...............................................–40°C to 85°C Junction Temperature (Note 2).............................. 125°C Storage Temperature Range................... –65°C to 125°C Lead Temperature G Package (Soldering, 10 sec).. 300°C Peak Body Temperature UH Package.................... 240°C PIN CONFIGURATION TOP VIEW 33 TG1 IN+ 5 32 SW1 IN– 6 31 BOOST2 DIFFOUT 7 EAIN SGND SW1 34 BOOST1 4 TG1 3 FCB BOOST1 PLLFLTR TOP VIEW CLKOUT 35 PGOOD PLLIN 2 PLLFLTR PLLIN FCB 36 CLKOUT IN + VCC 1 32 31 30 29 28 27 26 25 IN – 1 24 BOOST2 DIFFOUT 2 23 TG2 30 TG2 EAIN 3 22 SW2 8 29 SW2 SENSE1 + 9 28 VDR SENSE1 – 5 SENSE1+ 10 27 BG1 SENSE2 + 6 19 PGND SENSE1– 11 26 PGND SENSE2 – 7 18 BG2 SENSE2 + 12 25 BG2 SENSE3 – 8 SENSE2 – 13 24 BG3 SENSE3 – 14 23 SW3 SENSE3+ 15 22 TG3 ITH 17 UVADJ 18 21 BOOST3 20 PHASMD 19 SGND2 G PACKAGE 36-LEAD PLASTIC SSOP TJMAX = 125°C, θJA = 95°C/W, θJC = 32°C/W 21 VCC 33 SGND 20 BG1 17 BG3 SW3 TG3 BOOST3 UVADJ ITH RUN/SS SENSE3 + 9 10 11 12 13 14 15 16 PHASMD/PG RUN/SS 16 4 UH PACKAGE 32-LEAD (5mm × 5mm) PLASTIC QFN TJMAX = 125°C, θJA = 34°C/W EXPOSED PAD (PIN 33) IS SGND, MUST BE SOLDERED TO PCB 3731fc 2 LTC3731 ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING PACKAGE DESCRIPTION TEMPERATURE RANGE LTC3731CG#PBF LTC3731CG#TRPBF LTC3731CG 36-Lead Plastic SSOP 0°C to 70°C LTC3731IG#PBF LTC3731IG#TRPBF LTC3731IG 36-Lead Plastic SSOP –40°C to 85°C LTC3731CUH#PBF LTC3731CUH#TRPBF 3731 32-Lead (5mm × 5mm) Plastic QFN 0°C to 70°C LTC3731IUH#PBF LTC3731IUH#TRPBF 3731I 32-Lead (5mm × 5mm) Plastic QFN –40°C to 85°C Consult LTC Marketing for parts specified with wider operating temperature ranges. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VCC = VRUN/SS = 5V unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS LTC3731I l l 0.596 0.594 0.591 0.600 0.600 0.604 0.606 0.609 V V V VEAIN = 0.5V, VITH Open, VSENSE1–, VSENSE2–, VSENSE3– = 0.6V, 1.8V LTC3731I l l 65 62 60 75 75 85 88 90 mV mV mV 5 % 0.5 0.7 –0.5 –0.7 % % % % Main Control Loop VREGULATED Regulated Voltage at IN+ VSENSEMAX Maximum Current Sense Threshold VITH = 1.2V (Note 3) IMATCH Maximum Current Threshold Match Worst-Case Error at VSENSEMAX VLOADREG Output Voltage Load Regulation (Note 3) Measured in Servo Loop, ∆ITH Voltage = 1.2V to 0.7V LTC3731I Measured in Servo Loop, ∆ITH Voltage = 1.2V to 2V LTC3731I VREFLNREG Output Voltage Line Regulation VCC = 4.5V to 7V gm Transconductance Amplifier gm ITH = 1.2V, Sink/Source 25µA (Note 3) LTC3731I gmOL Transconductance Amplifier GBW ITH = 1.2V (gm • ZL, ZL = Series 1k-100kΩ-1nF) VFCB Forced Continuous Threshold IFCB FCB Bias Current VFCB = 0.65V VBINHIBIT Burst Inhibit Threshold Measured at FCB Pin VCC Lowered Until the RUN/SS Pin is Pulled Low LTC3731I –5 0.1 0.1 –0.1 –0.1 l l l l 0.03 %/V l l 4 3 5 5 6 7 l l 0.58 0.54 0.60 0.60 0.62 0.66 V V 0.2 0.7 µA 3 mmho mmho MHz VCC – 1.5 VCC – 0.7 VCC – 0.3 V 3.3 3.8 4.5 V 1.13 1.18 1.23 V At UVADJ Threshold 0.2 50 nA Input DC Supply Current Normal Mode Shutdown (Note 4) VCC = 5V VRUN/SS = 0V 2.3 50 3.5 100 mA µA Soft-Start Charge Current VRUN/SS = 1.9V –1.5 –2.5 µA UVR Undervoltage RUN/SS Reset UVADJ Undervoltage Lockout Threshold IUVADJ Undervoltage Bias Current IQ IRUN/SS –0.8 3731fc 3 LTC3731 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VCC = VRUN/SS = 5V unless otherwise noted. SYMBOL PARAMETER CONDITIONS VRUN/SS RUN/SS Pin ON Threshold VRUN/SS, Ramping Positive VRUN/SSARM RUN/SS Pin Arming Threshold MIN TYP MAX 1 1.5 1.9 UNITS V VRUN/SS, Ramping Positive Until Short-Circuit Latch-Off is Armed 3.8 4.5 V 3.2 VRUN/SSLO RUN/SS Pin Latch-Off Threshold VRUN/SS, Ramping Negative ISCL RUN/SS Discharge Current Soft-Short Condition VEAIN = 0.375V, VRUN/SS = 4.5V ISDLHO Shutdown Latch Disable Current VEAIN = 0.375V, VRUN/SS = 4.5V 1.5 5 µA ISENSE SENSE Pins Source Current SENSE1+, SENSE1–, SENSE2+, SENSE2–, SENSE3+, SENSE3– All Equal 1.2V; Current at Each Pin 13 20 µA DFMAX Maximum Duty Factor In Dropout, VSENSEMAX ≤ 30mV TG tR,tF Top Gate Rise Time Top Gate Fall Time CLOAD = 3300pF CLOAD = 3300pF 30 40 90 90 ns ns BG tR, tF Bottom Gate Rise Time Bottom Gate Fall Time CLOAD = 3300pF CLOAD = 3300pF 30 20 90 90 ns ns TG/BG t1D Top Gate Off to Bottom Gate On Delay All Controllers, CLOAD = 3300pF Each Driver Synchronous Switch-On Delay Time 50 ns BG/TG t2D Bottom Gate Off to Top Gate On Delay All Controllers, CLOAD = 3300pF Each Driver Top Switch-On Delay Time 60 ns tON(MIN) Minimum On-Time Tested with a Square Wave (Note 5) 110 ns 0.1 0.5 0.3 1.0 1 µA –10 ±3 10 µA –7 7 –10 10 –13 13 % % 100 150 µs –5 95 V –1.5 µA 98.5 % Power Good Output Indication VPGL PGOOD Voltage Output Low IPGOOD = 2mA, G Package IPGOOD = 1.6mA, UH Package IPGOOD PGOOD Output Leakage VPGOOD = 5V, G Package IPGOOD PGOOD/PHASMD Bias I 0 ≤ VPHASMD/PG ≤ VCC, UH Package VPGTHNEG VPGTHPOS PGOOD Trip Thresholds VDIFFOUT Ramping Negative VDIFFOUT Ramping Positive VDIFFOUT with Respect to Set Output Voltage, HGOOD Goes Low After VUVDLY Delay VPGDLY Power Good Fault Report Delay After VEAIN is Forced Outside the PGOOD Thresholds V V Oscillator and Phase-Locked Loop fNOM Nominal Frequency VPLLFLTR = 1.2V 360 400 440 kHz fLOW Lowest Frequency VPLLFLTR = 0V 190 225 260 kHz 600 680 750 kHz fHIGH Highest Frequency VPLLFLTR = 2.4V VPLLTH PLLIN Input Threshold Minimum Pulse Width > 100ns RPLLIN PLLIN Input Resistance IPLLFLTR Phase Detector Output Current Sinking Capability Sourcing Capability RRELPHS Controller 2-Controller 1 Phase Controller 3-Controller 1 Phase CLKOUT Controller 1 TG to CLKOUT Phase fPLLIN < fOSC fPLLIN > fOSC PHASMD = 0V PHASMD = 5V 1 V 50 kΩ 20 20 µA µA 120 240 Deg Deg 30 60 Deg Deg 3731fc 4 LTC3731 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VCC = VRUN/SS = 5V unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS 0.995 1.000 1.005 V/V 0.5 5 mV Differential Amplifier AV Differential Gain VOS Input Offset Voltage Magnitude IN+ = IN– = 1.2V, I CMRR Common Mode Rejection Ratio 0V < IN+ = IN– < 5V, IOUT = 1mA, Input Referred ICL Output Current Sourcing GBP Gain-Bandwidth Product IOUT = 1mA SR Slew Rate RL = 2k VO(MAX) Maximum High Output Voltage IOUT = 1mA RIN Input Resistance Measured at IN+ Pin OUT = 1mA, Input Referred; Gain = 1 Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: TJ is calculated from the ambient temperature TA and power dissipation PD according to the following formula: LTC3731CG/LTC3731IG: TJ = TA + (PD • 95°C/W) LTC3731CG/LTC3731IG: TJ = TCASE + (PD • 32°C/W) LTC3731CUH/LTC3731IUH: TJ = TA + (PD • 34°C/W) Note 3: The IC is tested in a feedback loop that includes the differential amplifier loaded with 100µA to ground driving the error amplifier and servoing the resultant voltage to the midrange point for the error amplifier (VITH = 1.2V). 50 70 10 40 mA 2 MHz 5 V/µs VCC – 1.2 VCC – 0.8 80 dB V kΩ Note 4: Dynamic supply current is higher due to the gate charge being delivered at the switching frequency. See Applications Information. Note 5: The minimum on-time condition corresponds to an inductor peak-to-peak ripple current of ≥ 40% of IMAX (see minimum on-time considerations in the Applications Information Section). Note 6: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. Junction temperature will exceed 125°C when overtemperature protection is active. Continuous operation above the specified maximum operating junction temperature may impair device reliability. 3731fc 5 LTC3731 TYPICAL PERFORMANCE CHARACTERISTICS Efficiency vs IOUT (Figure 14) Efficiency vs VIN (Figure 14) 100 95 80 VFCB = 5V VFCB = 0V 70 90 60 50 40 0.1 1 10 VIN = 5V IL = 45A 70 60 50 100 5 0 10 15 VIN (V) 20 600 595 5.5 5.0 4.5 4.0 –50 125 –25 0 25 50 75 TEMPERATURE (°C) 700 700 VO = 1.75V 75 VO = 0.6V 70 65 –50 125 –25 0 25 50 75 TEMPERATURE (°C) 100 125 3731 G06 Undervoltage Reset Voltage vs Temperature Operating Frequency vs VPLLFLTR 5 VPLLFLTR = 2.4V 500 VPLLFLTR = 1.2V 300 VPLLFLTR = 0V 100 0 –50 –25 0 25 50 75 100 125 TEMPERATURE (°C) 3731 G07 600 UNDERVOLTAGE RESET (V) VPLLFLTR = 5V OPERATING FREQUENCY (kHz) FREQUENCY (kHz) 100 80 3731 G05 Oscillator Frequency vs Temperature 200 Maximum ISENSE Threshold vs Temperature 85 3731 G04 400 600 500 3731 G03 MAXIMUM ISENSE THRESHOLD (mV) 605 400 300 FREQUENCY (kHz) 6.0 ERROR AMPLIFIER gm (mmho) REFERENCE VOLTAGE (mV) 610 100 VIN = 20V 75 200 25 Error Amplifier gm vs Temperature 0 25 50 75 TEMPERATURE (°C) VIN = 8V 3731 G02 Reference Voltage vs Temperature 600 VIN = 12V 85 55 3731 G01 –25 90 80 LOAD CURRENT (A) 590 –50 ILOAD = 20A VOUT = 1.5V 95 75 20 0 IL = 15A 80 65 VIN = 8V VOUT = 1.5V VOUT = 1.5V f = 250kHz 85 30 10 Efficiency vs Frequency (Figure 14) 100 EFFICIENCY (%) 90 VFCB = OPEN EFFICIENCY (%) EFFICIENCY (%) 100 500 400 300 200 0 0.5 1 1.5 2 PLLFLTR PIN VOLTAGE (V) 2.5 4 3 2 1 0 –50 –25 0 25 50 75 100 125 TEMPERATURE (°C) 3731 G08 3731 G09 3731fc 6 LTC3731 TYPICAL PERFORMANCE CHARACTERISTICS Short-Circuit Arming and Latchoff vs Temperature 80 2.4 SUPPLY CURRENT (mA) 4 LATCHOFF 3 2 1 2.0 60 1.6 40 1.2 0.8 20 2.5 SHUTDOWN CURRENT (µA) RUN/SS PIN VOLTAGE (V) ARMING 100 VCC = 5V 2.8 0.4 0 –50 –25 0 25 50 75 100 0 –50 125 –25 0 TEMPERATURE (°C) 25 50 75 100 0 125 0 25 50 75 TEMPERATURE (°C) 40 30 20 5 100 50 25 0 6 0 20 40 60 DUTY FACTOR (%) 3731 G13 30 20 0 10 20 30 40 50 60 70 80 90 100 PERCENTAGE OF NOMINAL OUTPUT VOLTAGE (%) 3731 G16 0 0.6 1.2 VITH (V) 1.8 30 98 96 94 92 90 –50 2.4 ISENSE Pin Current vs VOUT 20 10 0 –10 –20 10 0 0 40 ISENSE PIN CURRENT (µA) MAXIMUM DUTY FACTOR (%) 40 15 3731 G15 VPLLFLTR = 0V 70 50 30 Maximum Duty Factor vs Temperature 100 60 45 –15 100 80 60 3731 G14 Percentage of Nominal Output vs Peak ISENSE (Foldback) 125 Peak Current Threshold vs VITH 10 PEAK ISENSE VOLTAGE (mV) –25 75 ISENSE VOLTAGE THRESHOLD (mV) ISENSE VOLTAGE (mV) MAXIMUM ISENSE (mV) 50 80 0.5 Maximum Current Sense Threshold vs Duty Factor 60 3 4 VRUN/SS VOLTAGE (V) 1.0 3731 G12 70 2 1.5 0 –50 75 1 2.0 3731 G11 Maximum ISENSE vs VRUN/SS 0 VRUN/SS = 1.9V TEMPERATURE (°C) 3731 G10 0 RUN/SS PULL-UP CURRENT (µA) 5 80 RUN/SS Pull-Up Current vs Temperature Supply Current vs Temperature –25 0 25 50 75 TEMPERATURE (°C) 100 125 3731 G17 –30 0 1 3 2 VOUT (V) 4 5 3731 G18 3731fc 7 LTC3731 TYPICAL PERFORMANCE CHARACTERISTICS Differential Amplifier Gain-Phase 0 –3 –45 –6 –90 –9 –135 –12 –180 –15 0001 0.01 0.1 1 10 PHASE (DEG) GAIN (dB) 0 –225 FREQUENCY (MHz) 3731 G19 Shed Mode at 1 Amp, Light Load Current (Circuit of Figure 14) Burst Mode at 1 Amp, Light Load Current (Circuit of Figure 14) VOUT AC, 20mV/DIV VOUT AC, 20mV/DIV VSW1 10V/DIV VSW1 10V/DIV VSW2 10V/DIV VSW3 10V/DIV VSW2 10V/DIV VSW3 10V/DIV 4µs/DIV VIN = 12V VOUT = 1.5V VFCB = VCC FREQUENCY = 250kHz 4µs/DIV VIN = 12V VOUT = 1.5V VFCB = OPEN FREQUENCY = 250kHz 3731 G20 Transient Load Current Response: 0 Amp to 50 Amp (Circuit of Figure 14) Continuous Mode at 1 Amp, Light Load Current (Circuit of Figure 14) VOUT AC, 20mV/DIV 3731 G21 VOUT AC, 20mV/DIV VSW1 10V/DIV ILOAD 20A/DIV VSW2 10V/DIV VSW3 10V/DIV VIN = 12V 4µs/DIV VOUT = 1.5V VFCB = 0V FREQUENCY = 250kHz 3731 G22 VIN = 12V 20µs/DIV VOUT = 1.5V VFCB = VCC FREQUENCY = 250kHz 3731 G23 3731fc 8 LTC3731 PIN FUNCTIONS BG1 to BG3: High Current Gate Drives for Bottom N‑Channel MOSFETs. Voltage swing at these pins is from ground to VCC. BOOST1 to BOOST3: Positive Supply Pins to the Topside Floating Drivers. Bootstrapped capacitors, charged with external Schottky diodes and a boost voltage source, are connected between the BOOST and SW pins. Voltage swing at the BOOST pins is from boost source voltage (typically VCC) to this boost source voltage + VIN (where VIN is the external MOSFET supply rail). CLKOUT: Output clock signal available to synchronize other controller ICs for additional MOSFET stages/phases. DIFFOUT: Output of the Remote Output Voltage Sensing Differential Amplifier. EAIN: This is the input to the error amplifier that compares the feedback voltage to the internal 0.6V reference voltage. FCB: Forced Continuous Control Input. The voltage applied to this pin sets the operating mode of the controller. The forced continuous current mode is active when the applied voltage is less than 0.6V. Burst Mode operation will be active when the pin is allowed to float and a Stage Shedding mode will be active if the pin is tied to the VCC pin. (Do not apply voltage directly to this pin prior to the application of voltage on the VCC pin.) PGOOD: This open-drain output is pulled low when the output voltage has been outside the PGOOD tolerance window for the VPGDLY delay of approximately 100µs. IN+, IN–: Inputs to a precision, unity-gain differential amplifier with internal precision resistors. This provides true remote sensing of both the positive and negative load terminals for precise output voltage control. ITH: Error Amplifier Output and Switching Regulator Compensation Point. All three current comparator’s thresholds increase with this control voltage. PGND: Driver Power Ground. This pin connects directly to the sources of the bottom N-channel external MOSFETs and the (–) terminals of CIN. PHASMD: This pin determines the phase shift between the first controller’s rising TG signal and the rising edge of the CLKOUT signal. Logic 0 yields 30 degrees and Logic 1 yields 60 degrees. Note: the PHASMD and PGOOD functions are internally tied together in the LTC3731 UH package. PLLIN: Synchronization Input to Phase Detector. This pin is internally terminated to SGND with 50kΩ. The phase-locked loop will force the rising top gate signal of controller 1 to be synchronized with the rising edge of the PLLIN signal. PLLFLTR: The phase-locked loop’s lowpass filter is tied to this pin. Alternatively, this pin can be driven with an AC or DC voltage source to vary the frequency of the internal oscillator. (Do not apply voltage directly to this pin prior to the application of voltage on the VCC pin.) RUN/SS: Combination of Soft-Start, Run Control Input and Short-Circuit Detection Timer. A capacitor to ground at this pin sets the ramp time to full current output as well as the time delay prior to an output voltage short-circuit shutdown. A minimum value of 0.01µF is recommended on this pin. SENSE1+, SENSE2+, SENSE3+, SENSE1–, SENSE2–, SENSE3–: The Inputs to Each Differential Current Comparator. The ITH pin voltage and built-in offsets between SENSE– and SENSE+ pins, in conjunction with RSENSE, set the current trip threshold level. SGND: Signal Ground. This pin must be routed separately under the IC to the PGND pin and then to the main ground plane. The exposed pad on the LTC3731 UH package is SGND and must be soldered to the PCB. SW1 to SW3: Switch Node Connections to Inductors. Voltage swing at these pins is from a Schottky diode (external) voltage drop below ground to VIN (where VIN is the external MOSFET supply rail). TG1 to TG3: High Current Gate Drives for Top N-channel MOSFETs. These are the outputs of floating drivers with a voltage swing equal to the boost voltage source superimposed on the switch node voltage SW. UVADJ: Input to the Undervoltage Shutdown Comparator. When the applied input voltage is less than 1.2V, this comparator turns off the output MOSFET driver stages and discharges the RUN/SS capacitor. 3731fc 9 LTC3731 PIN FUNCTIONS VDR: (LTC3731G Package Only) Supplies power to the bottom gate drivers only. This pin needs to be very carefully and closely decoupled to the IC’s PGND pin. VCC: Main Supply Pin. This pin supplies the controller circuit power. In the LTC3731 UH package, it also supplies the high power pulses to drive the external MOSFET gates. This pin needs to be very carefully and closely decoupled to the IC’s PGND pin. FUNCTIONAL DIAGRAM PLLIN PHASE DET FIN 50k RLP PLLFLTR CLP CLKOUT CLK1 CLK2 CLK3 OSCILLATOR PHASMD** PGOOD** – 0.66V DUPLICATE FOR SECOND AND THIRD CONTROLLER CHANNELS + 100µs DELAY DROP OUT DET PROTECTION + + 0.6V – IN – FCB 40k 40k 0.54V S RS LATCH R 40k B 0.55V 40k PGND – + – + + R1 0.600V + + 0.660V – + 36k SENSE 54k SS CLAMP OV RSENSE COUT + EA L VCC – 36k SENSE 54k VOUT 2.4V – FCB 1.2V SHED 0.600V VCC RC I2 5(VFB) 0.86V ITH CC – + 3mV SLOPE COMP – BG BOT FCB SHDN I1 VFB CIN VCC (VDR)*** DIFFOUT EAIN + SW SWITCH LOGIC Q CB TG TOP FORCE BOT Q – A1 + IN+ BOT VIN DB BOOST EAIN – FCB R2 VCC 1.5µA SHDN RST 5(VFB) 6V RUN SOFTSTART INTERNAL SUPPLY UV RESET UVADJ VREF VCC SGND* VCC + CCC RUN/SS – 1.2V CSS + 3731 F02 *THE LTC3731UH USES THE EXPOSED DIE ATTACH PAD FOR THE SGND CONNECTIONS **THE PHASMD AND PGOOD PIN FUNCTIONS ARE TIED TOGETHER IN THE LTC3731 UH PACKAGE ***LTC3731CG/IG ONLY 10 Figure 2 3731fc LTC3731 OPERATION (Refer to Functional Diagram) Main Control Loop Low Current Operation The IC uses a constant frequency, current mode step-down architecture. During normal operation, each top MOSFET is turned on each cycle when the oscillator sets the RS latch, and turned off when the main current comparator, I1, resets each RS latch. The peak inductor current at which I1 resets the RS latch is controlled by the voltage on the ITH pin, which is the output of the error amplifier EA. The EAIN pin receives a portion of output voltage feedback signal via the DIFFOUT pin through the external resistive divider and is compared to the internal reference voltage. When the load current increases, it causes a slight decrease in the EAIN pin voltage relative to the 0.6V reference, which in turn causes the ITH voltage to increase until each inductor’s average current matches one third of the new load current (assuming all three current sensing resistors are equal). In Burst Mode operation and Stage Shedding mode, after each top MOSFET has turned off, the bottom MOSFET is turned on until either the inductor current starts to reverse, as indicated by current comparator I2, or the beginning of the next cycle. The FCB pin is a logic input to select between three modes of operation. The top MOSFET drivers are biased from floating bootstrap capacitor CB, which is normally recharged through an external Schottky diode when the top FET is turned off. When VIN decreases to a voltage close to VOUT, however, the loop may enter dropout and attempt to turn on the top MOSFET continuously. The dropout detector counts the number of oscillator cycles that the bottom MOSFET remains off and periodically forces a brief on period to allow CB to recharge. The main control loop is shut down by pulling the RUN/ SS pin low. Releasing RUN/SS allows an internal 1.5µA current source to charge soft-start capacitor CSS. When CSS reaches 1.5V, the main control loop is enabled and the internally buffered ITH voltage is clamped but allowed to ramp as the voltage on CSS continues to ramp. This “softstart” clamping prevents abrupt current from being drawn from the input power source. When the RUN/SS pin is low, all functions are kept in a controlled state. The RUN/SS pin is pulled low when the supply input voltage is below 4V, when the undervoltage lockout pin (UVADJ) is below 1.2V, or when the IC die temperature rises above 150°C. A) Burst Mode Operation When the FCB pin voltage is below 0.6V, the controller performs as a continuous, PWM current mode synchronous switching regulator. The top and bottom MOSFETs are alternately turned on to maintain the output voltage independent of direction of inductor current. When the FCB pin is below VCC – 1.5V but greater than 0.6V, the controller performs as a Burst Mode switching regulator. Burst Mode operation sets a minimum output current level before turning off the top switch and turns off the synchronous MOSFET(s) when the inductor current goes negative. This combination of requirements will, at low current, force the ITH pin below a voltage threshold that will temporarily shut off both output MOSFETs until the output voltage drops slightly. There is a burst comparator having 60mV of hysteresis tied to the ITH pin. This hysteresis results in output signals to the MOSFETs that turn them on for several cycles, followed by a variable “sleep” interval depending upon the load current. The resultant output voltage ripple is held to a very small value by having the hysteretic comparator after the error amplifier gain block. B) Stage Shedding Operation When the FCB pin is tied to the VCC pin, Burst Mode operation is disabled and the forced minimum inductor current requirement is removed. This provides constant frequency, discontinuous current operation over the widest possible output current range. At approximately 10% of maximum designed load current, the second and third output stages are shut off and the phase 1 controller alone is active in discontinuous current mode. This “stage shedding” optimizes efficiency by eliminating the gate charging losses and switching losses of the other two output stages. Additional cycles will be skipped when the output load current drops below 1% of maximum designed load current in order to maintain the output voltage. This stage shedding operation is not as efficient as Burst Mode operation at very light loads, but does provide lower noise, constant frequency operating mode down to very light load conditions. 3731fc 11 LTC3731 OPERATION (Refer to Functional Diagram) C) Continuous Current Operation Tying the FCB pin to ground will force continuous current operation. This is the least efficient operating mode, but may be desirable in certain applications. The output can source or sink current in this mode. When sinking current while in forced continuous operation, the controller will cause current to flow back into the input filter capacitor. If large enough, the input capacitor will prevent the input supply from boosting to unacceptably high levels. See CIN/COUT Selection in the Applications Information section. Frequency Synchronization The phase-locked loop allows the internal oscillator to be synchronized to an external source using the PLLIN pin. The output of the phase detector at the PLLFLTR pin is also the DC frequency control input of the oscillator, which operates over a 250kHz to 600kHz range corresponding to a voltage input from 0V to 2.4V. When locked, the PLL aligns the turn on of the top MOSFET to the rising edge of the synchronizing signal. When no frequency information is supplied to the PLLIN pin, PLLFLTR goes low, forcing the oscillator to minimum frequency. A DC source can be applied to the PLLFLTR pin to externally set the desired operating frequency. A discharge current of approximately 20µA will be present at the pin with no PLLIN input signal. Input capacitance ESR requirements and efficiency losses are reduced substantially in a multiphase architecture because the peak current drawn from the input capacitor is effectively divided by the number of phases used and power loss is proportional to the RMS current squared. A 3-stage, single output voltage implementation can reduce input path power loss by 90%. Differential Amplifier This amplifier provides true differential output voltage sensing. Sensing both VOUT+ and VOUT– benefits regulation in high current applications and/or applications having electrical interconnection losses. This sensing also isolates the physical power ground from the physical signal ground preventing the possibility of troublesome “ground loops” on the PC layout and prevents voltage errors caused by board-to-board interconnects, particularly helpful in VRM designs. Power Good The PGOOD pin is connected to the drain of an internal N‑channel MOSFET. The MOSFET is turned on once an internal delay of about 100µs has elapsed and the output voltage has been away from its nominal value by greater than 10%. If the output returns to normal prior to the delay timeout, the timer is reset. There is no delay time for the rising of the PGOOD output once the output voltage is within the ±10% “window.” Phase Mode The PHASMD pin determines the phase shift between the rising edge of the TG1 output and the rising edge of the CLKOUT signal. Grounding the pin will result in 30 degrees phase shift and tying the pin to VCC will result in 60 degrees. These phase shift values enable extension to 6- and 12-phase systems. The PGOOD function above and the PHASMD function are tied to a common pin in the UH package. Undervoltage Shutdown Adjust The voltage applied to the UVADJ pin is compared to the internal 1.2V reference to have an externally programmable undervoltage shutdown. The RUN/SS pin is internally held low until the voltage applied to the UVADJ pin exceeds the 1.2V threshold. Short-Circuit Detection The RUN/SS capacitor is used initially to turn on and limit the inrush current from the input power source. Once the controllers have been given time, as determined by the capacitor on the RUN/SS pin, to charge up the output capacitors and provide full load current, the RUN/SS capacitor is then used as a short-circuit timeout circuit. If the output voltage falls to less than 70% of its nominal output voltage, the RUN/SS capacitor begins discharging, assuming that the output is in a severe overcurrent and/ or short-circuit condition. If the condition lasts for a long enough period, as determined by the size of the RUN/SS 3731fc 12 LTC3731 OPERATION (Refer to Functional Diagram) capacitor, the controller will be shut down until the RUN/ SS pin voltage is recycled. This built-in latchoff can be overridden by providing >5µA at a compliance of 3.8V to the RUN/SS pin. This additional current shortens the soft-start period but prevents net discharge of the RUN/SS capacitor during a severe overcurrent and/or short-circuit condition. Foldback current limiting is activated when the output voltage falls below 70% of its nominal level whether or not the short-circuit latchoff circuit is enabled. Foldback current limit can be overridden by clamping the EAIN pin such that the voltage is held above the (70%)(0.6V) or 0.42V level even when the actual output voltage is low. Up to 100µA of input current can safely be accommodated by the RUN/SS pin. Input Undervoltage Reset The RUN/SS capacitor will be reset if the input voltage (VCC) is allowed to fall below approximately 4V. The capacitor on the RUN/SS pin will be discharged until the short-circuit arming latch is disarmed. The RUN/SS capacitor will attempt to cycle through a normal soft-start ramp up after the VCC supply rises above 4V. This circuit prevents power supply latchoff in the event of input power switching break-before-make situations. The PGOOD pin is held low during start-up until the RUN/SS capacitor rises above the short-circuit latchoff arming threshold of approximately 3.8V. APPLICATIONS INFORMATION Operating Frequency The IC uses a constant frequency, phase-lockable architecture with the frequency determined by an internal capacitor. This capacitor is charged by a fixed current plus an additional current which is proportional to the voltage applied to the PLLFLTR pin. Refer to the Phase-Locked Loop and Frequency Synchronization section for additional information. A graph for the voltage applied to the PLLFLTR pin versus frequency is given in Figure 3. As the operating frequency is increased the gate charge losses will be higher, reducing 700 OPERATING FREQUENCY (kHz) The basic application circuit is shown in Figure 1 on the first page of this data sheet. External component selection is driven by the load requirement, and normally begins with the selection of an inductance value based upon the desired operating frequency, inductor current and output voltage ripple requirements. Once the inductors and operating frequency have been chosen, the current sensing resistors can be calculated. Next, the power MOSFETs and Schottky diodes are selected. Finally, CIN and COUT are selected according to the voltage ripple requirements. The circuit shown in Figure 1 can be configured for operation up to a MOSFET supply voltage of 28V (limited by the external MOSFETs and possibly the minimum on-time). 600 500 400 300 200 0 0.5 1 1.5 2 PLLFLTR PIN VOLTAGE (V) 2.5 3731 F03 Figure 3. Operating Frequency vs VPLLFLTR efficiency (see Efficiency Considerations). The maximum switching frequency is approximately 680kHz. Inductor Value Calculation and Output Ripple Current The operating frequency and inductor selection are interrelated in that higher operating frequencies allow the use of smaller inductor and capacitor values. So why would anyone ever choose to operate at lower frequencies with larger components? The answer is efficiency. A higher frequency generally results in lower efficiency because of MOSFET gate charge and transition losses. In addition to 3731fc 13 LTC3731 APPLICATIONS INFORMATION The inductor value has a direct effect on ripple current. The inductor ripple current ∆IL per individual section, N, decreases with higher inductance or frequency and increases with higher VIN or VOUT:  V  V ∆IL = OUT  1− OUT  fL  VIN  where f is the individual output stage operating frequency. In a PolyPhase converter, the net ripple current seen by the output capacitor is much smaller than the individual inductor ripple currents due to the ripple cancellation. The details on how to calculate the net output ripple current can be found in Application Note 77. Figure 4 shows the net ripple current seen by the output capacitors for the different phase configurations. The output ripple current is plotted for a fixed output voltage as the duty factor is varied between 10% and 90% on the x‑axis. The output ripple current is normalized against the inductor ripple current at zero duty factor. The graph can be used in place of tedious calculations. As shown in Figure 4, the zero output ripple current is obtained when: VOUT k = where k = 1, 2, ..., N – 1 VIN N So the number of phases used can be selected to minimize the output ripple current and therefore the output ripple voltage at the given input and output voltages. In applications having a highly varying input voltage, additional phases will produce the best results. Accepting larger values of ∆IL allows the use of low inductances but can result in higher output voltage ripple. A reasonable starting point for setting ripple current is ∆IL = 0.4(IOUT)/N, where N is the number of channels and IOUT is the total load current. Remember, the maximum ∆IL occurs at the maximum input voltage. The individual inductor ripple currents are constant, determined by the input and output voltages and the inductance. 1.0 1-PHASE 2-PHASE 3-PHASE 4-PHASE 6-PHASE 12-PHASE 0.9 0.8 0.7 IO(P-P) VO/fL this basic trade-off, the effect of inductor value on ripple current and low current operation must also be considered. The PolyPhase approach reduces both input and output ripple currents while optimizing individual output stages to run at a lower fundamental frequency, enhancing efficiency. 0.6 0.5 0.4 0.3 0.2 0.1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 DUTY FACTOR (VOUT/VIN) 0.8 0.9 3731 F04 Figure 4. Normalized Peak Output Current vs Duty Factor [IRMS = 0.3(IO(P-P)] Inductor Core Selection Once the value for L1 to L3 is determined, the type of inductor must be selected. High efficiency converters generally cannot afford the core loss found in low cost powdered iron cores, forcing the use of ferrite, molypermalloy or Kool Mµ cores. Actual core loss is independent of core size for a fixed inductor value, but it is very dependent on inductance selected. As inductance increases, core losses go down. Unfortunately, increased inductance requires more turns of wire and therefore copper losses will increase. Ferrite designs have very low core loss and are preferred at high switching frequencies, so design goals can concentrate on copper loss and preventing saturation. Ferrite core material saturates “hard,” which means that inductance collapses abruptly when the peak design current is exceeded. This results in an abrupt increase in inductor ripple current and consequent output voltage ripple. Do not allow the core to saturate! Molypermalloy (from Magnetics, Inc.) is a very good, low loss core material for toroids, but it is more expensive than ferrite. A reasonable compromise from the same manufacturer is Kool Mµ. Toroids are very space efficient, especially when you can use several layers of wire. Because they lack a bobbin, mounting is more difficult. However, designs for surface mount are available which do not increase the height significantly. 3731fc 14 LTC3731 APPLICATIONS INFORMATION Power MOSFET and D1, D2, D3 Selection At least two external power MOSFETs must be selected for each of the three output sections: One N-channel MOSFET for the top (main) switch and one or more N-channel MOSFET(s) for the bottom (synchronous) switch. The number, type and “on” resistance of all MOSFETs selected take into account the voltage step-down ratio as well as the actual position (main or synchronous) in which the MOSFET will be used. A much smaller and much lower input capacitance MOSFET should be used for the top MOSFET in applications that have an output voltage that is less than one-third of the input voltage. In applications where VIN >> VOUT, the top MOSFETs’ “on” resistance is normally less important for overall efficiency than its input capacitance at operating frequencies above 300kHz. MOSFET manufacturers have designed special purpose devices that provide reasonably low “on” resistance with significantly reduced input capacitance for the main switch application in switching regulators. The peak-to-peak MOSFET gate drive levels are set by the voltage, VCC, requiring the use of logic-level threshold MOSFETs in most applications. Pay close attention to the BVDSS specification for the MOSFETs as well; many of the logic-level MOSFETs are limited to 30V or less. Selection criteria for the power MOSFETs include the “on” resistance RDS(ON), input capacitance, input voltage and maximum output current. MOSFET input capacitance is a combination of several components but can be taken from the typical “gate charge” curve included on most data sheets (Figure 5). The curve is generated by forcing a constant input current into the gate of a common source, current source VIN VGS MILLER EFFECT a V b QIN CMILLER = (QB – QA)/VDS + VGS – Figure 5. Gate Charge Characteristic +V DS – 3731 F05 loaded stage and then plotting the gate voltage versus time. The initial slope is the effect of the gate-to-source and the gate-to-drain capacitance. The flat portion of the curve is the result of the Miller multiplication effect of the drain-to-gate capacitance as the drain drops the voltage across the current source load. The upper sloping line is due to the drain-to-gate accumulation capacitance and the gate-to-source capacitance. The Miller charge (the increase in coulombs on the horizontal axis from a to b while the curve is flat) is specified for a given VDS drain voltage, but can be adjusted for different VDS voltages by multiplying by the ratio of the application VDS to the curve specified VDS values. A way to estimate the CMILLER term is to take the change in gate charge from points a and b on a manufacturer’s data sheet and divide by the stated VDS voltage specified. CMILLER is the most important selection criteria for determining the transition loss term in the top MOSFET but is not directly specified on MOSFET data sheets. CRSS and COS are specified sometimes but definitions of these parameters are not included. When the controller is operating in continuous mode the duty cycles for the top and bottom MOSFETs are given by: Main Switch Duty Cycle = VOUT VIN  V –V  Synchronous Switch Duty Cycle =  IN OUT  VIN   The power dissipation for the main and synchronous MOSFETs at maximum output current are given by: V I  PMAIN = OUT  MAX  VIN  N  VIN2 2 (1+ δ )RDS(ON) + IMAX (R )(C )• 2N DR MILLER  1  1 +   ( f)  VCC – VTH(IL) VTH(IL)  V –V I  PSYNC = IN OUT  MAX   N  VIN 2 (1+ δ )RDS(ON) 3731fc 15 LTC3731 APPLICATIONS INFORMATION Both MOSFETs have I2R losses while the topside N‑channel equation includes an additional term for transition losses, which peak at the highest input voltage. For VIN < 12V, the high current efficiency generally improves with larger MOSFETs, while for VIN > 12V, the transition losses rapidly increase to the point that the use of a higher RDS(ON) device with lower CMILLER actually provides higher efficiency. The synchronous MOSFET losses are greatest at high input voltage when the top switch duty factor is low or during a short-circuit when the synchronous switch is on close to 100% of the period. The term (1 + δ ) is generally given for a MOSFET in the form of a normalized RDS(ON) vs temperature curve, but δ = 0.005/°C can be used as an approximation for low voltage MOSFETs. The Schottky diodes (D1 to D3 in Figure 1) conduct during the dead time between the conduction of the two large power MOSFETs. This prevents the body diode of the bottom MOSFET from turning on, storing charge during the dead time and requiring a reverse recovery period which could cost as much as several percent in efficiency. A 2A to 8A Schottky is generally a good compromise for both regions of operation due to the relatively small average current. Larger diodes result in additional transition loss due to their larger junction capacitance. CIN and COUT Selection In continuous mode, the source current of each top N‑channel MOSFET is a square wave of duty cycle VOUT/ VIN. A low ESR input capacitor sized for the maximum RMS current must be used. The details of a close form equation can be found in Application Note 77. Figure 6 shows the input capacitor ripple current for different phase configurations with the output voltage fixed and input voltage varied. The input ripple current is normalized against the DC output current. The graph can be used in place of tedious calculations. The minimum input ripple current can be achieved when the product of phase number and output voltage, N(VOUT), is approximately equal to the input voltage VIN or: VOUT k = where k = 1, 2, ..., N – 1 VIN N So the phase number can be chosen to minimize the input capacitor size for the given input and output voltages. In the graph of Figure 4, the local maximum input RMS capacitor currents are reached when: VOUT 2k – 1 = where k = 1, 2, ..., N VIN N These worst-case conditions are commonly used for design because even significant deviations do not offer much relief. Note that capacitor manufacturer’s ripple current ratings are often based on only 2000 hours of life. This makes it advisable to further derate the capacitor or to choose a capacitor rated at a higher temperature than required. Several capacitors may also be paralleled to meet size or 0.6 RMS INPUT RIPPLE CURRENT DC LOAD CURRENT where N is the number of output stages, δ is the temperature dependency of RDS(ON), RDR is the effective top driver resistance (approximately 2Ω at VGS = VMILLER), VIN is the drain potential and the change in drain potential in the particular application. VTH(IL) is the data sheet specified typical gate threshold voltage specified in the power MOSFET data sheet at the specified drain current. CMILLER is the calculated capacitance using the gate charge curve from the MOSFET data sheet and the technique described above. 0.5 1-PHASE 2-PHASE 3-PHASE 4-PHASE 6-PHASE 12-PHASE 0.4 0.3 0.2 0.1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 DUTY FACTOR (VOUT/VIN) 0.8 0.9 3731 F06 Figure 6. Normalized Input RMS Ripple Current vs Duty Factor for One to Six Output Stages 3731fc 16 LTC3731 APPLICATIONS INFORMATION height requirements in the design. Always consult the capacitor manufacturer if there is any question. where f = operating frequency of each stage, N is the number of output stages, COUT = output capacitance and ∆IL = ripple current in each inductor. The output ripple is highest at maximum input voltage since ∆IL increases with input voltage. The output ripple will be less than 50mV at max VIN with ∆IL = 0.4IOUT(MAX) assuming: The Figure 6 graph shows that the peak RMS input current is reduced linearly, inversely proportional to the number N of stages used. It is important to note that the efficiency loss is proportional to the input RMS current squared and therefore a 3-stage implementation results in 90% less power loss when compared to a single phase design. Battery/input protection fuse resistance (if used), PC board trace and connector resistance losses are also reduced by the reduction of the input ripple current in a PolyPhase system. The required amount of input capacitance is further reduced by the factor, N, due to the effective increase in the frequency of the current pulses. and Ceramic capacitors are becoming very popular for small designs but several cautions should be observed. “X7R”, “X5R” and “Y5V” are examples of a few of the ceramic materials used as the dielectric layer, and these different dielectrics have very different effect on the capacitance value due to the voltage and temperature conditions applied. Physically, if the capacitance value changes due to applied voltage change, there is a concommitant piezo effect which results in radiating sound! A load that draws varying current at an audible rate may cause an attendant varying input voltage on a ceramic capacitor, resulting in an audible signal. A secondary issue relates to the energy flowing back into a ceramic capacitor whose capacitance value is being reduced by the increasing charge. The voltage can increase at a considerably higher rate than the constant current being supplied because the capacitance value is decreasing as the voltage is increasing! Nevertheless, ceramic capacitors, when properly selected and used, can provide the lowest overall loss due to their extremely low ESR. Manufacturers such as Nichicon, Nippon Chemi-Con and Sanyo should be considered for high performance throughhole capacitors. The OS-CON semiconductor dielectric capacitor available from Sanyo and the Panasonic SP surface mount types have a good (ESR)(size) product. Once the ESR requirement for COUT has been met, the RMS current rating generally far exceeds the IRIPPLE(P-P) requirement. Ceramic capacitors from AVX, Taiyo Yuden, Murata and Tokin offer high capacitance value and very low ESR, especially applicable for low output voltage applications. The selection of COUT is driven by the required effective series resistance (ESR). Typically once the ESR requirement is satisfied the capacitance is adequate for filtering. The steady-state output ripple (∆VOUT) is determined by:  1  ∆VOUT ≈ ∆IRIPPLE  ESR + 8NfCOUT   COUT required ESR < N • RSENSE COUT > 1/(8Nf)(RSENSE) The emergence of very low ESR capacitors in small, surface mount packages makes very small physical implementations possible. The ability to externally compensate the switching regulator loop using the ITH pin allows a much wider selection of output capacitor types. The impedance characteristics of each capacitor type is significantly different than an ideal capacitor and therefore requires accurate modeling or bench evaluation during design. In surface mount applications, multiple capacitors may have to be paralleled to meet the ESR or RMS current handling requirements of the application. Aluminum electrolytic and dry tantalum capacitors are both available in surface mount configurations. New special polymer surface mount capacitors offer very low ESR also but have much lower capacitive density per unit volume. In the case of tantalum, it is critical that the capacitors are surge tested for use in switching power supplies. Several excellent choices are the AVX TPS, AVX TPSV, the KEMET T510 series of surface-mount tantalums or the Panasonic SP series of surface mount special polymer capacitors 3731fc 17 LTC3731 APPLICATIONS INFORMATION available in case heights ranging from 2mm to 4mm. Other capacitor types include Sanyo POSCAP, Sanyo OS-CON, Nichicon PL series and Sprague 595D series. Consult the manufacturers for other specific recommendations. RSENSE Selection for Output Current Once the frequency and inductor have been chosen, RSENSE1, RSENSE2, RSENSE3 are determined based on the required peak inductor current. The current comparator has a typical maximum threshold of 75mV/RSENSE and an input common mode range of SGND to (1.1) • VCC. The current comparator threshold sets the peak inductor current, yielding a maximum average output current IMAX equal to the peak value less half the peak-to-peak ripple current, ∆IL. Allowing a margin for variations in the IC and external component values yields: 50mV RSENSE = N IMAX The IC works well with values of RSENSE from 0.002Ω to 0.02Ω. VCC Decoupling The VCC pin supplies power not only to the internal circuits of the controller but also to the top and bottom gate drivers in the LTC3731 UH package, and therefore must be bypassed very carefully to ground with a ceramic capacitor, type X7R or X5R (depending upon the operating temperature environment) of at least 1µF immediately next to the IC and preferably an additional 10µF placed very close to the IC due to the extremely high instantaneous currents involved. The total capacitance, taking into account the voltage coefficient of ceramic capacitors, should be 100 times as large as the total combined gate charge capacitance of ALL of the MOSFETs being driven. Good bypassing close to the IC is necessary to supply the high transient currents required by the MOSFET gate drivers while keeping the 5V supply quiet enough so as not to disturb the very small-signal high bandwidth of the current comparators. Topside MOSFET Driver Supply (CB, DB) External bootstrap capacitors, CB, connected to the BOOST pins, supply the gate drive voltages for the topside MOSFETs. Capacitor CB in the Functional Diagram is charged though diode DB from VCC when the SW pin is low. When one of the topside MOSFETs turns on, the driver places the CB voltage across the gate-source of the desired MOSFET. This enhances the MOSFET and turns on the topside switch. The switch node voltage, SW, rises to VIN and the BOOST pin follows. With the topside MOSFET on, the boost voltage is above the input supply (VBOOST = VCC + VIN). The value of the boost capacitor CB needs to be 30 to 100 times that of the total gate charge capacitance of the topside MOSFET(s) as specified on the manufacturer’s data sheet. The reverse breakdown of DB must be greater than VIN(MAX). Differential Amplifier/Output Voltage Programming The IC has a true remote voltage sense capability. The sensing connections should be returned from the load, back to the differential amplifier’s inputs through a common, tightly coupled pair of PC traces. The differential amplifier rejects common mode signals capacitively or inductively radiated into the feedback PC traces as well as ground loop disturbances. The differential amplifier output signal is divided down with an external resistive divider and compared with the internal, precision 0.6V voltage reference by the error amplifier. The differential amplifier has an output swing range of 0V to VCC – 1.2V. The output uses an NPN emitter follower without any internal pull-down current. A DC resistive load to ground is required in order to sink current. The differential amplifier is not recommended for high output voltage applications. However, if it is used, monitor the VCC rail with the UVADJ function to turn off the controller before the differential amplifier runs out of headroom. The output voltage is set by an external resistive divider according to the following formula:  R1 VOUT = 0.6V  1+   R2  3731fc 18 LTC3731 APPLICATIONS INFORMATION The resistive divider is connected to the output as shown in Figure 2, allowing remote voltage sensing. Soft-Start/Run Function The RUN/SS pin provides three functions: 1) ON/OFF, 2) soft-start and 3) a defeatable short-circuit latch off timer. Soft-start reduces the input power sources’ surge currents by gradually increasing the controller’s current limit (proportional to an internal buffered and clamped VITH). The latchoff timer prevents very short, extreme load transients from tripping the overcurrent latch. A small pull-up current (>5µA) supplied to the RUN/SS pin will prevent the overcurrent latch from operating. A maximum pullup current of 200µA is allowed into the RUN/SS pin even though the voltage at the pin may exceed the absolute maximum rating for the pin. This is a result of the limited current and the internal protection circuit on the pin. The following explanation describes how this function operates. An internal 1.5µA current source charges up the CSS capacitor. When the voltage on RUN/SS reaches 1.5V, the controller is permitted to start operating. As the voltage on RUN/SS increases from 1.5V to 3.5V, the internal current limit is increased from 20mV/RSENSE to 75mV/RSENSE. The output current limit ramps up slowly, taking an additional 1s/µF to reach full current. The output current thus ramps up slowly, eliminating the starting surge current required from the input power supply. If RUN/SS has been pulled all the way to ground, there is a delay before starting of approximately: 1.5V tDELAY = C = (1s/µF ) CSS 1.5µA SS tIRAMP = 3V − 1.5V C = (1s/µF ) CSS 1.5µA SS By pulling the RUN/SS controller pin below 0.4V the IC is put into low current shutdown (IQ < 100 µA). The RUN/SS pin can be driven directly from logic as shown in Figure 7. Diode, D1, in Figure 7 reduces the start delay but allows CSS to ramp up slowly, providing the soft-start function. The RUN/SS pin has an internal 6V zener clamp (see the Functional Diagram). 3.3V OR 5V RUN/SS PIN VCC RUN/SS PIN 5V D1 SHDN CSS RSS SHDN CSS 3731 F07 Figure 7. RUN/SS Pin Interfacing Fault Conditions: Overcurrent Latchoff The RUN/SS pins also provide the ability to latch off the controllers when an overcurrent condition is detected. The RUN/SS capacitor is used initially to turn on and limit the inrush current of all three output stages. After the controllers have been started and been given adequate time to charge up the output capacitor and provide full load current, the RUN/SS capacitor is used for a short-circuit timer. If the output voltage falls to less than 70% of its nominal value, the RUN/SS capacitor begins discharging on the assumption that the output is in an overcurrent condition. If the condition lasts for a long enough period, as determined by the size of the RUN/SS capacitor, the discharge current, and the circuit trip point, the controller will be shut down until the RUN/SS pin voltage is recycled. If the overload occurs during start-up, the time can be approximated by: tLO1 >> (CSS • 0.6V)/(1.5µA) = 4 • 105 (CSS) If the overload occurs after start-up, the voltage on the RUN/SS capacitor will continue charging and will provide additional time before latching off: tLO2 >> (CSS • 3V)/(1.5µA) = 2 • 106 (CSS) This built-in overcurrent latchoff can be overridden by providing a pull-up resistor to the RUN/SS pin from VCC as shown in Figure 7. When VCC is 5V, a 200k resistance will prevent the discharge of the RUN/SS capacitor during an overcurrent condition but also shortens the soft-start period, so a larger RUN/SS capacitor value may be required. Why should you defeat overcurrent latchoff? During the prototyping stage of a design, there may be a problem with noise pick-up or poor layout causing the protection circuit to latch off the controller. Defeating this feature allows 3731fc 19 LTC3731 APPLICATIONS INFORMATION troubleshooting of the circuit and PC layout. The internal foldback current limiting still remains active, thereby protecting the power supply system from failure. A decision can be made after the design is complete whether to rely solely on foldback current limiting or to enable the latchoff feature by removing the pull-up resistor. The value of the soft-start capacitor CSS may need to be scaled with output current, output capacitance and load current characteristics. The minimum soft-start capacitance is given by: CSS > (COUT )(VOUT) (10 –4) (RSENSE) The minimum recommended soft-start capacitor of CSS = 0.1µF will be sufficient for most applications. Current Foldback In certain applications, it may be desirable to defeat the internal current foldback function. A negative impedance is experienced when powering a switching regulator. That is, the input current is higher at a lower VIN and decreases as VIN is increased. Current foldback is designed to accommodate a normal, resistive load having increasing current draw with increasing voltage. The EAIN pin should be artificially held 70% above its nominal operating level of 0.6V, or 0.42V in order to prevent the IC from “folding back” the peak current level. A suggested circuit is shown in Figure 8. The emitter of Q1 will hold up the EAIN pin to a voltage in the absence of VOUT that will prevent the internal sensing circuitry from reducing the peak output current. Removing the function in this manner eliminates the external MOSFET’s protective feature under short-circuit conditions. This technique will also prevent the short-circuit latchoff VCC VCC LTC3731 Q1 CALCULATE FOR 0.42V TO 0.55V EAIN 3731 F08 Figure 8. Foldback Current Elimination function from turning off the part during a short-circuit event and the peak output current will only be limited to N • 75mV/RSENSE. Undervoltage Reset In the event that the input power source to the IC (VCC) drops below 4V, the RUN/SS capacitor will be discharged to ground. When VCC rises above 4V, the RUN/SS capacitor will be allowed to recharge and initiate another soft-start turn-on attempt. This may be useful in applications that switch between two supplies that are not diode connected, but note that this cannot make up for the resultant interruption of the regulated output. Phase-Locked Loop and Frequency Synchronization The IC has a phase-locked loop comprised of an internal voltage controlled oscillator and phase detector. This allows the top MOSFET of output stage 1’s turn-on to be locked to the rising edge of an external source. The frequency range of the voltage controlled oscillator is ±50% around the center frequency fO. A voltage applied to the PLLFLTR pin of 1.2V corresponds to a frequency of approximately 400kHz. The nominal operating frequency range of the IC is 225kHz to 680kHz. The phase detector used is an edge sensitive digital type that provides zero degrees phase shift between the external and internal oscillators. This type of phase detector will not lock the internal oscillator to harmonics of the input frequency. The PLL hold-in range, ∆fH, is equal to the capture range, ∆fC: ∆fH = ∆fC = ±0.5 fO The output of the phase detector is a complementary pair of current sources charging or discharging the external filter components on the PLLFLTR pin. A simplified block diagram is shown in Figure 9. If the external frequency (fPLLIN) is greater than the oscillator frequency, fOSC, current is sourced continuously, pulling up the PLLFLTR pin. When the external frequency is less than fOSC, current is sunk continuously, pulling down the PLLFLTR pin. If the external and internal frequencies are the same, but exhibit a phase difference, the current sources turn on for an amount of time corresponding to 3731fc 20 LTC3731 APPLICATIONS INFORMATION PHASE DETECTOR/ OSCILLATOR EXTERNAL OSC RLP 10k 2.4V CLP OSC PLLIN 50k PLLFLTR DIGITAL PHASE/ FREQUENCY DETECTOR 3731 F09 Figure 9. Phase-Locked Loop Block Diagram the phase difference. Thus, the voltage on the PLLFLTR pin is adjusted until the phase and frequency of the external and internal oscillators are identical. At this stable operating point, the phase comparator output is open and the filter capacitor CLP holds the voltage. The IC PLLIN pin must be driven from a low impedance source such as a logic gate located close to the pin. When using multiple ICs for a phase-locked system, the PLLFLTR pin of the master oscillator should be biased at a voltage that will guarantee the slave oscillator(s) ability to lock onto the master’s frequency. A voltage of 1.7V or below applied to the master oscillator’s PLLFLTR pin is recommended in order to meet this requirement. The resultant operating frequency will be approximately 550kHz for 1.7V. The loop filter components (CLP, RLP) smooth out the current pulses from the phase detector and provide a stable input to the voltage controlled oscillator. The filter components CLP and RLP determine how fast the loop acquires lock. Typically RLP =10k and CLP ranges from 0.01µF to 0.1µF. Minimum On-Time Considerations Minimum on-time, tON(MIN), is the smallest time duration that the IC is capable of turning on the top MOSFET. It is determined by internal timing delays and the gate charge of the top MOSFET. Low duty cycle applications may approach this minimum on-time limit and care should be taken to ensure that: tON(MIN ) < VOUT VIN ( f ) If the duty cycle falls below what can be accommodated by the minimum on-time, the IC will begin to skip every other cycle, resulting in half-frequency operation. The output voltage will continue to be regulated, but the ripple current and ripple voltage will increase. The minimum on-time for the IC is generally about 110ns. However, as the peak sense voltage decreases the minimum on-time gradually increases. This is of particular concern in forced continuous applications with low ripple current at light loads. If the duty cycle drops below the minimum on-time limit in this situation, a significant amount of cycle skipping can occur with correspondingly larger current and voltage ripple. If an application can operate close to the minimum on-time limit, an inductor must be chosen that is low enough in value to provide sufficient ripple amplitude to meet the minimum on-time requirement. As a general rule, keep the inductor ripple current for each channel equal to or greater than 30% of IOUT(MAX) at VIN(MAX). Efficiency Considerations The percent efficiency of a switching regulator is equal to the output power divided by the input power times 100%. It is often useful to analyze individual losses to determine what is limiting the efficiency and which change would produce the most improvement. Percent efficiency can be expressed as: %Efficiency = 100% – (L1 + L2 + L3 + ...) where L1, L2, etc. are the individual losses as a percentage of input power. Checking Transient Response The regulator loop response can be checked by looking at the load transient response. Switching regulators take several cycles to respond to a step in DC (resistive) load current. When a load step occurs, VOUT shifts by an amount equal to ∆ILOAD • ESR, where ESR is the effective series resistance of COUT. ∆ILOAD also begins to charge or discharge COUT, generating the feedback error signal that forces the regulator to adapt to the current change and return VOUT to its steady-state value. During 3731fc 21 LTC3731 APPLICATIONS INFORMATION this recovery time, VOUT can be monitored for excessive overshoot or ringing, which would indicate a stability problem. The availability of the ITH pin not only allows optimization of control loop behavior, but also provides a DC coupled and AC filtered closed-loop response test point. The DC step, rise time and settling at this test point truly reflects the closed-loop response. Assuming a predominantly second order system, phase margin and/ or damping factor can be estimated using the percentage of overshoot seen at this pin. The bandwidth can also be estimated by examining the rise time at the pin. The ITH external components shown in the Figure 1 circuit will provide an adequate starting point for most applications. The ITH series RC-CC filter sets the dominant pole-zero loop compensation. The values can be modified slightly (from 0.2 to 5 times their suggested values) to maximize transient response once the final PC layout is done and the particular output capacitor type and value have been determined. The output capacitors need to be decided upon because the various types and values determine the loop feedback factor gain and phase. An output current pulse of 20% to 80% of full load current having a rise time of 1µF) supply bypass capacitors. The discharged bypass capacitors are effectively put in parallel with COUT, causing a rapid drop in VOUT. No regulator can alter its delivery of current quickly enough to prevent this sudden step change in output voltage if the load switch resistance is low and it is driven quickly. If CLOAD is greater than 2% of COUT , the switch rise time should be controlled so that the load rise time is limited to approximately 1000 • RSENSE • CLOAD. Thus a 250µF capacitor and a 2mΩ RSENSE resistor would require a 500µs rise time, limiting the charging current to about 1A. Automotive Considerations: Plugging into the Cigarette Lighter As battery-powered devices go mobile, there is a natural interest in plugging into the cigarette lighter in order to conserve or even recharge battery packs during operation. But before you connect, be advised: you are plugging into the supply from hell. The main battery line in an automobile is the source of a number of nasty potential transients, including load dump, reverse battery and double battery. Load dump is the result of a loose battery cable. When the cable breaks connection, the field collapse in the alternator can cause a positive spike as high as 60V which takes several hundred milliseconds to decay. Reverse battery is just what it says, while double battery is a consequence of tow-truck operators finding that a 24V jump start cranks cold engines faster than 12V. The network shown in Figure 10 is the most straightforward approach to protect a DC/DC converter from the ravages of an automotive battery line. The series diode prevents current from flowing during reverse battery, while the transient suppressor clamps the input voltage during load dump. Note that the transient suppressor should not conduct during double-battery operation, but must still clamp the input voltage below breakdown of the converter. Although the IC has a maximum input voltage of 32V on 3731fc 22 LTC3731 APPLICATIONS INFORMATION VBAT 12V VCC 5V + Next verify the minimum on-time is not violated. The minimum on-time occurs at maximum VCC: LTC3731 3731 F10 Figure 10. Automotive Application Protection the SW pins, most applications will be limited to 30V by the MOSFET BVDSS. tON(MIN ) = = 1.3V  1.3V  1− ( 400kHz )(30%)(15A )  20V  PMAIN ≈ RSENSE1, RSENSE2 and RSENSE3 can be calculated by using a conservative maximum sense current threshold of 65mV and taking into account half of the ripple current: RSENSE = 65mV = 0.0037Ω  34%  15A  1+  2  Use a commonly available 0.003Ω sense resistor. 1.8V 2 15) 1+ ( 0.005) ( 50°C − 25°C)  ( 20V 2  45A  0.007Ω + ( 20 )   ( 2Ω ) (1000pF )  ( 2) ( 3)  1  1   5V – 1.8V + 1.8V  ( 400kHz ) = 2.2W The worst-case power dissipation by the synchronous MOSFET under normal operating conditions at elevated ambient temperature and estimated 50°C junction temperature rise is: ≥ 0.68µH Using L = 0.6µH, a commonly available value results in 34% ripple current. The worst-case output ripple for the three stages operating in parallel will be less than 11% of the peak output current. 1.3V = 162ns 20V ( 400kHz ) The power dissipation on the topside MOSFET can be estimated. Using a Fairchild FDS6688 for example, RDS(ON) = 7mΩ, CMILLER = 15nC/15V = 1000pF. At maximum input voltage with T(estimated) = 50°C: As a design example, assume VCC = 5V, VIN = 12V(nominal), VIN = 20V(max), VOUT = 1.3V, IMAX = 45A and f = 400kHz. The inductance value is chosen first based upon a 30% ripple current assumption. The highest value of ripple current in each output stage occurs at the maximum input voltage. VOUT  VOUT  1− f ( ∆I)  VIN  VIN(MAX) ( f ) = The output voltage will be set by the resistive divider from the DIFFOUT pin to SGND, R1 and R2 in the Functional Diagram. Set R1 = 13.3k and R2 = 11.3k. Design Example L= VOUT PSYNC = 20V − 1.3V (15A )2 (1.25)(0.007Ω) = 1.84W 20V A short-circuit to ground will result in a folded back current of: ISC ≈ 25mV 1  150ns ( 20V )  +  = 7.5A (2 + 3)mΩ 2  0.6µH  with a typical value of RDS(ON) and d = (0.005/°C)(50°C) = 0.25. The resulting power dissipated in the bottom MOSFET is: PSYNC = (7.5A)2(1.25)(0.007Ω) ≈ 0.5W 3731fc 23 LTC3731 APPLICATIONS INFORMATION which is less than one third of the normal, full load conditions. Incidentally, since the load no longer dissipates any power, total system power is decreased by over 90%. Therefore, the system actually cools significantly during a shorted condition! PC Board Layout Checklist When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the IC. These items are also illustrated graphically in the layout diagram of Figure 11. Check the following in the PC layout: L1 SW1 RSENSE1 D1 L2 VIN SW2 RIN + CIN VOUT RSENSE2 COUT D2 BOLD LINES INDICATE HIGH, SWITCHING CURRENTS. KEEP LINES TO A MINIMUM LENGTH. + RL L3 SW3 RSENSE3 D3 3731 F11 Figure 11. Branch Current Waveforms 3731fc 24 LTC3731 APPLICATIONS INFORMATION 1) Are the signal and power ground paths isolated? Keep the SGND at one end of a printed circuit path thus preventing MOSFET currents from traveling under the IC. The IC signal ground pin should be used to hook up all control circuitry on one side of the IC, routing the copper through SGND, under the IC covering the “shadow” of the package, connecting to the PGND pin and then continuing on to the (–) plates of CIN and COUT. The VCC decoupling capacitor should be placed immediately adjacent to the IC between the VCC pin and PGND. A 1µF ceramic capacitor of the X7R or X5R type is small enough to fit very close to the IC to minimize the ill effects of the large current pulses drawn to drive the bottom MOSFETs. An additional 5µF to 10µF of ceramic, tantalum or other very low ESR capacitance is recommended in order to keep the internal IC supply quiet. The power ground returns to the sources of the bottom N‑channel MOSFETs, anodes of the Schottky diodes and (–) plates of CIN, which should have as short lead lengths as possible. 2) Does the IC IN+ pin connect to the (+) plates of COUT? A 30pF to 300pF feedforward capacitor between the IN+ and EAIN pins should be placed as close as possible to the IC. 3) Are the SENSE– and SENSE+ printed circuit traces for each channel routed together with minimum PC trace spacing? The filter capacitors between SENSE+ and SENSE– for each channel should be as close as possible to the pins of the IC. Connect the SENSE– and SENSE+ pins to the pads of the sense resistor as illustrated in Figure 12. INDUCTOR LTC3731 SENSE+ SENSE– 1000pF SENSE RESISTOR 3731 F12 4) Do the (+) plates of CPWR connect to the drains of the topside MOSFETs as closely as possible? This capacitor provides the pulsed current to the MOSFETs. 5) Keep the switching nodes, SWITCH, BOOST and TG away from sensitive small-signal nodes (SENSE+, SENSE –, IN+, IN–, EAIN). Ideally the SWITCH, BOOST and TG printed circuit traces should be routed away and separated from the IC and especially the “quiet” side of the IC. Separate the high dv/dt traces from sensitive small-signal nodes with ground traces or ground planes. 6) Use a low impedance source such as a logic gate to drive the PLLIN pin and keep the lead as short as possible. 7) The 47pF to 330pF ceramic capacitor between the ITH pin and signal ground should be placed as close as possible to the IC. Figure 11 illustrates all branch currents in a three-phase switching regulator. It becomes very clear after studying the current waveforms why it is critical to keep the high switching current paths to a small physical size. High electric and magnetic fields will radiate from these “loops” just as radio stations transmit signals. The output capacitor ground should return to the negative terminal of the input capacitor and not share a common ground path with any switched current paths. The left half of the circuit gives rise to the “noise” generated by a switching regulator. The ground terminations of the synchronous MOSFETs and Schottky diodes should return to the bottom plate(s) of the input capacitor(s) with a short isolated PC trace since very high switched currents are present. A separate isolated path from the bottom plate(s) of the input and output capacitor(s) should be used to tie in the IC power ground pin (PGND). This technique keeps inherent signals generated by high current pulses taking alternate current paths that have finite impedances during the total period of the switching regulator. External OPTI-LOOP compensation allows overcompensation for PC layouts which are not optimized but this is not the recommended design procedure. OUTPUT CAPACITOR Figure 12. Kelvin Sensing RSENSE 3731fc 25 LTC3731 APPLICATIONS INFORMATION Simplified Visual Explanation of How a 3-Phase Controller Reduces Both Input and Output RMS Ripple Current The effect of multiphase power supply design significantly reduces the amount of ripple current in both the input and output capacitors. The RMS input ripple current is divided by, and the effective ripple frequency is multiplied up by the number of phases used (assuming that the input voltage is greater than the number of phases used times the output voltage). The output ripple amplitude is also reduced by, and the effective ripple frequency is increased by the number of phases used. Figure 13 graphically illustrates the principle. The worst-case input RMS ripple current for a single stage design peaks at twice the value of the output voltage. The worst-case input RMS ripple current for a two stage design results in peaks at one-fourth and three-fourths of the input voltage, and the worst-case input RMS ripple current for a three stage design results in peaks at one-sixth, one-half and five-sixths of the input voltage. The peaks, however, are at ever decreasing levels with the addition of more phases. A higher effective duty factor results because the duty factors “add” as long as the currents in each stage are balanced. Refer to AN19 for a detailed description of how to calculate RMS current for the single stage switching regulator. Figure 6 illustrates the RMS input current drawn from the input capacitance versus the duty cycle as determined by the ratio of input and output voltage. The peak input RMS current level of the single phase system is reduced by two-thirds in a 3-phase solution due to the current splitting between the three stages. The output ripple current is reduced significantly when compared to the single phase solution using the same inductance value because the VOUT/L discharge currents term from the stages that has their bottom MOSFETs on subtract current from the (VCC – VOUT)/L charging current resulting from the stage which has its top MOSFET on. The output ripple current for a 3-phase design is: IP-P = VOUT (1– 3DC) VIN > 3VOUT ( f )(L ) SINGLE PHASE VSW ICIN ICOUT TRIPLE PHASE VSW1 VSW2 VSW3 IL1 IL2 IL3 ICIN ICOUT 3731 F13 Figure 13. Single and PolyPhase Current Waveforms 3731fc 26 LTC3731 APPLICATIONS INFORMATION The ripple frequency is also increased by three, further reducing the required output capacitance when VCC < 3VOUT as illustrated in Figure 6. The addition of more phases, by phase locking additional controllers, always results in no net input or output ripple at VOUT/VIN ratios equal to the number of stages implemented. Designing a system with multiple stages close to the VOUT/VIN ratio will significantly reduce the ripple voltage at the input and outputs and thereby improve efficiency, physical size and heat generation of the overall switching power supply. Refer to Application Note 77 for more information on PolyPhase circuits. Efficiency Calculation To estimate efficiency, the DC loss terms include the input and output capacitor ESR, each MOSFET RDS(ON), inductor resistance RL, the sense resistance RSENSE and the forward drop of the Schottky rectifier at the operating output current and temperature. Typical values for the design example given previously in this data sheet are: Main MOSFET RDS(ON) = 7mΩ (9mΩ at 90°C) Sync MOSFET RDS(ON) = 7mΩ (9mΩ at 90°C) CINESR = 20mΩ COUTESR = 3mΩ RL = 2.5mΩ RSENSE = 3mΩ VSCHOTTKY = 0.8V at 15A (0.7V at 90°C) VOUT = 1.3V VIN = 12V IMAX = 45A δ = 0.5%°C (MOSFET temperature coefficient) N=3 f = 400kHz The main MOSFET is on for the duty factor VOUT/VIN and the synchronous MOSFET is on for the rest of the period or simply (1 – VOUT/VIN). Assuming the ripple current is small, the AC loss in the inductor can be made small if a good quality inductor is chosen. The average current, IOUT, is used to simplify the calculations. The equation below is not exact but should provide a good technique for the comparison of selected components and give a result that is within 10% to 20% of the final application. Determining the MOSFETs’ die temperature may require iterative calculations if one is not familiar with typical performance. A maximum operating junction temperature of 90° to 100°C for the MOSFETs is recommended for high reliability applications. Common output path DC loss: I  PCOMPATH ≈N  MAX   N  2 (RL +RSENSE ) + COUTESR Loss This totals 3.7W + COUTESR loss. Total of all three main MOSFETs’ DC loss: V I  PMAIN = N  OUT   MAX   VIN   N  2 ( 1+ δ ) RDS(ON) + CINESR Loss This totals 0.87W + CINESR loss (at 90°C). Total of all three synchronous MOSFETs’ DC loss:  I V  PSYNC = N  1– OUT   MAX  VIN   N   2 ( 1+ δ ) RDS(ON) This totals 7.2W at 90°C. Total of all three main MOSFETs’ AC loss: PMAIN ≈ 3(VIN )2 45A (2Ω)(1000pF) (2)(3) 1  1   5V – 1.8V + 1.8V  (400kHz) = 6.3W 3731fc 27 LTC3731 APPLICATIONS INFORMATION This totals 1W at VIN = 8V, 2.25W at VIN = 12V and 6.25W at VIN = 20V. Total of all three synchronous MOSFETs’ AC gate loss: (3)QG VIN VDSSPEC (f) = (6)(15nC) VIN VDSSPEC (4E5) This totals 0.08W at VIN = 8V, 0.12W at VIN = 12V and 0.19W at VIN = 20V. The bottom MOSFET does not experience the Miller capacitance dissipation issue that the main switch does because the bottom switch turns on when its drain is close to ground. The Schottky rectifier loss assuming 50ns nonoverlap time: 2 • 3(0.7V)(15A)(50ns)(4E5) This totals 1.26W. The total output power is (1.3V)(45A) = 58.5W and the total input power is approximately 60W so the % loss of each component is as follows: Main switch’s AC loss (VIN = 12V) 2.25W 3.75% Main switch’s DC loss 0.87W 1.5% Synchronous switch AC loss 0.19W 0.3% Synchronous switch DC loss 7.2W 12% Power path loss 3.7W 6.1% The numbers above represent the values at VIN = 12V. It can be seen from this simple example that two things can be done to improve efficiency: 1) Use two MOSFETs on the synchronous side and 2) use a smaller MOSFET for the main switch with smaller CMILLER to better balance the AC loss with the DC loss. A smaller, less expensive MOSFET can actually perform better in the task of the main switch. 3731fc 28 LTC3731 TYPICAL APPLICATIONS 1µF OPTIONAL FILTER FOR SYNCHRONIZATION 1000pF 10k 1 VCC SYNC IN 300kHz 0.01µF 2 3 4 5 100pF 300pF 6.04k 6 9.09k 7 8 9 10 S1+ 1000pF S1– 11 12 S2+ 0.01µF 1000pF S2– 13 S3– 14 1000pF S3+ 15 16 ITH 17 330pF 3.3nF 2.2k VIN 18 18k VCC 10Ω CLK VCC PLLIN PLLFLTR PGOOD BOOST1 FCB TG1 IN+ SW1 IN– LTC3731G BOOST2 DIFFOUT TG2 EAIN SW2 SGND VDR SENSE1+ BG1 SENSE1– PGND SENSE2+ BG2 SENSE2– BG3 SENSE3– SW3 SENSE3+ TG3 RUN/SS ITH UVADJ BOOST3 PHASMD SGND 36 35 PGOOD NC 47k 34 0.1µF 33 1Ω M1 32 VCC 31 0.1µF 30 VCC 5V TO 7V VIN M2 29 VOUT 1.5V AT 65A L1 D1 0.002Ω + S1 S1– 10µF 6.3V ×3 + VIN 28 M3 27 1µF 26 10µF 25 L2 M4 0.002Ω D2 S2+ 10µF 25V ×5 + COUT VIN CIN 3.3V TO 20V 68µF 25V S2– 24 23 VIN 22 M5 0.1µF 21 20 M6 L3 0.002Ω D3 S3+ 19 S3– VCC 12k 3731 F14 VIN: 3.3V TO 20V VOUT: 1.5V AT 65A SWITCHING FREQUENCY: 300kHz CIN: SANYO OS-CON 25SP68M COUT: 270F/2V ×8 PANASONIC SP EEUE0D271R OR 470F/2.5V ×6 SANYO POSCAP 2R5 TPD470M D1 TO D3: DIODES INC. B340A L1 TO L3: 0.8H SUMIDA CEP125-0R8 M1, M3, M5: IRF7821W ×2, Si7860DP OR HAT2168 ×2 M2, M4, M6: IRF7832 ×2, Si7892DP ×2 OR HAT2165 ×2 Figure 14. 3-Phase 65A Power Supply 3731fc 29 LTC3731 TYPICAL APPLICATIONS VCC VCC VCC 8.2k 4 5 VOUTS+ 220pF VOUTS– 15k 8 EAIN 9 10 1000pF S1– 11 12 S2+ 1000pF S2– 13 14 S3– 1000pF S3+ 0.1µF DIFFOUT 10Ω ×6 S1+ 6 7 330pF 15 16 RUN/SS VIN 2 3 3.3k 4.7k 1 17 357k 18 CLKOUT VCC PLLIN PLLFLTR PGOOD BOOST1 FCB TG1 IN+ SW1 IN– LTC3731G BOOST2 DIFFOUT TG2 EAIN SW2 SGND VDR SENSE1+ BG1 SENSE1– PGND SENSE2+ BG2 SENSE2– BG3 SENSE3– SW3 SENSE3+ TG3 RUN/SS ITH BOOST3 PHASMD UVADJ SGND2 36 35 + 10Ω 1µF PGOOD 10k CLK1 34 1Ω 0.1µF 33 BOOST2 L1 X2 M2,3 31 0.1µF BOOST3 10µF CER 10µF 10V VIN M1 32 30 BOOST1 D1 29 0.002Ω S1+ S1– VIN 28 1µF + CER 27 26 M4 4.7µF 25 L2 X2 M5,6 0.002Ω D2 S2+ S2– 24 23 VIN 22 0.1µF 21 20 19 M7 L3 X2 M8,9 VCC 0.002Ω D3 S3+ S3– VOUT 121k + 100pF 1000pF VCC 0.01µF CLK1 1 2 3 4 1000pF VOUTS+ 5 VOUTS– 6 DIFFOUT S4+ S4– S5+ S5– S6– ITH 100pF S6+ 10pF 10Ω ×6 9 10 1000pF 11 12 1000pF 13 14 1000pF 15 16 RUN/SS 1.2k 7 8 EAIN 270pF V5 UVADJ 1000pF 10k V5 17 18 2700pF VCC CLKOUT PLLIN PLLFLTR PGOOD BOOST4 FCB TG4 IN+ SW4 IN– LTC3731G BOOST5 DIFFOUT TG5 EAIN SW5 SGND VDR SENSE4+ BG4 SENSE4– PGND SENSE5+ BG5 SENSE5– BG6 SENSE6– SW6 SENSE6+ TG6 RUN/SS ITH UVADJ BOOST6 PHASMD SGND2 36 35 CLKOUT PGOOD BOOST4 34 33 0.1µF BOOST5 10Ω 0.1µF 29 L4 D4 VIN CIN 0.002Ω S4+ S4– VIN 28 26 + VIN X2 M11,12 31 27 BOOST6 M10 32 30 COUT 1µF + CER M13 4.7µF 25 X2 M14,15 L5 0.002Ω D5 S5+ S5– 24 23 VIN 22 21 0.1µF M16 19 0.002Ω 3731 F15 X2 M17,18 20 L6 D6 S6+ S6– UVADJ NOTES: V5: 5V TO 7V VIN: 10V TO 14V; VOUT: 2.5V/100A SWITCHING FREQUENCY: 500kHz (V5 = 5V) M1, M4, M7, M10, M13, M16: SILICONIX Si7390DP OR HAT2168 M2, M3, M5, M6, M8, M9, M11, M12, M14, M15, M17, M18: SILICONIX Si7356DP OR HAT2165 D1 TO D6: B320A L1 TO L6: TOKO FDH1040: 0.56µH CIN: 10µF/16V CERAMIC × 10 + 270F/16V SANYO OS-CON COUT: 100µF/6.3V/X5R × 10 + 330F/4V × 8 Figure 15. 2.5V/100A Power Supply 3731fc 30 LTC3731 PACKAGE DESCRIPTION G Package 36-Lead Plastic SSOP (5.3mm) (Reference LTC DWG # 05-08-1640) 12.50 – 13.10* (.492 – .516) 1.25 ±0.12 7.8 – 8.2 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 5.3 – 5.7 0.42 ±0.03 7.40 – 8.20 (.291 – .323) 0.65 BSC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 RECOMMENDED SOLDER PAD LAYOUT 2.0 (.079) MAX 5.00 – 5.60** (.197 – .221) 0° – 8° 0.09 – 0.25 (.0035 – .010) 0.55 – 0.95 (.022 – .037) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS MILLIMETERS 2. DIMENSIONS ARE IN (INCHES) 0.65 (.0256) BSC 0.22 – 0.38 (.009 – .015) TYP 0.05 (.002) MIN G36 SSOP 0204 3. DRAWING NOT TO SCALE *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED .152mm (.006") PER SIDE **DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED .254mm (.010") PER SIDE 3731fc 31 LTC3731 PACKAGE DESCRIPTION UH Package 32-Lead Plastic QFN (5mm × 5mm) (Reference LTC DWG # 05-08-1693 Rev D) 0.70 ±0.05 5.50 ±0.05 4.10 ±0.05 3.50 REF (4 SIDES) 3.45 ± 0.05 3.45 ± 0.05 PACKAGE OUTLINE 0.25 ± 0.05 0.50 BSC RECOMMENDED SOLDER PAD LAYOUT APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 5.00 ± 0.10 (4 SIDES) BOTTOM VIEW—EXPOSED PAD 0.75 ± 0.05 R = 0.05 TYP 0.00 – 0.05 R = 0.115 TYP PIN 1 NOTCH R = 0.30 TYP OR 0.35 × 45° CHAMFER 31 32 0.40 ± 0.10 PIN 1 TOP MARK (NOTE 6) 1 2 3.50 REF (4-SIDES) 3.45 ± 0.10 3.45 ± 0.10 (UH32) QFN 0406 REV D 0.200 REF NOTE: 1. DRAWING PROPOSED TO BE A JEDEC PACKAGE OUTLINE M0-220 VARIATION WHHD-(X) (TO BE APPROVED) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 0.25 ± 0.05 0.50 BSC 3731fc 32 LTC3731 REVISION HISTORY (Revision history begins at Rev C) REV DATE DESCRIPTION PAGE NUMBER C 7/11 Updated Features section 1 Updated Differential Amplifier section in Electrical Characteristics 5 Updated text in Differential Amplifier/Output Voltage Programming 18 Updated Typical Application and Related Parts 34 3731fc Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 33 LTC3731 TYPICAL APPLICATION 1µF 1 VCC 2 3 SHORT PLLFLTR TO SGND 4 5 100pF 20k 6 147k 7 8 9 10 S1+ 1000pF S1– 11 12 S2+ 0.01µF 1000pF S2– 13 S3– 14 1000pF S3+ 15 16 ITH 17 100pF 10nF 3.01k VIN 18 18k V5 10Ω CLK VCC PLLIN PGOOD PLLFLTR BOOST1 FCB TG1 IN+ SW1 LTC3731G BOOST2 IN– DIFFOUT TG2 EAIN SW2 SGND VDR SENSE1+ BG1 SENSE1– PGND SENSE2+ BG2 SENSE2– BG3 SENSE3– SW3 SENSE3+ TG3 RUN/SS ITH BOOST3 PHASMD UVADJ SGND 36 35 PGOOD NC 47k 34 1Ω 0.1µF 33 M1 32 V5 31 0.1µF 30 V5 5V TO 7V VIN M2 29 D1 0.003Ω + S1 S1– 47µF 10V ×3 + VIN 28 M3 27 26 VOUT 5V AT 40A L1 10µF 1µF 25 M4 L2 0.003Ω D2 S2+ 4.7µF 50V ×6 + S2– COUT VIN CIN 9V TO 28V 47µF 35V ×4 24 23 VIN 22 M5 0.1µF 21 20 M6 L3 0.003Ω D3 S3+ 19 S3– V5 12k 3731 TA01 VIN: 9V TO 28V VOUT: 5V AT 40A SWITCHING FREQUENCY: 225kHz CIN: KEMET T521X476M035ATE070 ×4 COUT: SANYO 6TPE220MI ×3 D1 TO D3: DIODES INC. B340A L1 TO L3: 2.2µH WURTH 7443320220 M1, M3, M5: RJK0305DPB M2, M4, M6: RJK0330DPB RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC3829 3-Phase, Single Output Synchronous Step-Down Controller with Diff Amp and DCR Temperature Compensation Phase-Lockable Fixed 250kHz to 770kHz Frequency, 4.5V ≤ VIN ≤ 38V, 0.8V ≤ VOUT ≤ 5V LTC3856 2-Phase, Single Output Synchronous Step-Down DC/DC Controller with Diff Amp and DCR Temperature Compensation Phase-Lockable Fixed 250kHz to 770kHz Frequency, 4.5V ≤ VIN ≤ 38V, 0.8V ≤ VOUT ≤ 5V LTC3855 Dual, Multiphase, Synchronous Step-Down DC/DC Controller with Diffamp and DCR Temperature Compensation Phase-Lockable Fixed Frequency 250kHz to 770kHz, 4.5V ≤ VIN ≤ 38V, 0.8V ≤ VOUT ≤ 12V LTC3860 Dual, Multiphase, Synchronous Step-Down DC/DC Controller with Diffamp and Three-State Output Drive Operates with Power Blocks or DRMOS Devices, 3V ≤ VIN ≤ 24V, tON(MIN) = 20ns Triple Output, Multiphase Synchronous Step-Down DC/DC Controller, Phase-Lockable Fixed 250kHz to 750kHz Frequency, 4V ≤ VIN ≤ 24V, VOUT3 Up to 13.5V RSENSE or DCR Current Sensing and Tracking LTC3869/LTC3869-2 Dual Output, 2-Phase Synchronous Step-Down DC/DC Controller, PLL Fixed 250kHz to 750kHz Frequency, with Accurate Current Share 4V ≤ VIN ≤ 38V, 0.6V ≤ VOUT ≤ 12.5V LTC3853 3731fc 34 Linear Technology Corporation LT 0711 REV C • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com  LINEAR TECHNOLOGY CORPORATION 2005
LTC3731CUH#TRPBF 价格&库存

很抱歉,暂时无法提供与“LTC3731CUH#TRPBF”相匹配的价格&库存,您可以联系我们找货

免费人工找货