APTGT100TA60P

APTGT100TA60P Triple phase leg Trench + Field Stop IGBT® Power Module VBUS1 VBUS2 VBUS3 VCES = 600V IC = 100A @ Tc = 80°C Applicatio n • Welding converters • Switched Mode Power Supplies • Uninterruptible Power Supplies • Motor control W G1 G3 G5 E1 U E3 V E5 G2 G4 G6 E2 0/VBUS1 E4 0/VBUS2 E6 0/VBUS3 Features • Trench + Field Stop IGBT® Technology - Low voltage drop - Low tail current - Switching frequency up to 20 kHz - Soft recovery parallel diodes - Low diode VF - Low leakage current - Avalanche energy rated - RBSOA and SCSOA rated • Kelvin emitter for easy drive • Very low stray inductance - Symmetrical design - Lead frames for power connections • High level of integration Benefits • Stable temperature behavior • Very rugged • Solderable terminals for easy PCB mounting • Direct mounting to heatsink (isolated package) • Low junction to case thermal resistance • Easy paralleling due to positive TC of VCEsat • Very low (12mm) profile • Each leg can be easily paralleled to achieve a phase leg of three times the current capability • Module can be configured as a three phase bridge • Module can be configured as a boost followed by a full bridge Max ratings 600 150 100 200 ±20 340 200A @ 550V Unit V APTGT100TA60P – Rev 0 May, 2005 VBUS 1 VBUS 2 VBUS 3 G1 0/VBUS 1 E1 E2 G2 0/VBUS 2 G3 E3 E4 G4 0/VBUS 3 G5 E5 E6 G6 U V W Absolute maximum ratings Symbol VCES IC ICM VGE PD RBSOA Parameter Collector - Emitter Breakdown Voltage Continuous Collector Current Pulsed Collector Current Gate – Emitter Voltage Maximum Power Dissipation TC = 25°C TC = 80°C TC = 25°C TC = 25°C Tj = 150°C A V W Reverse Bias Safe Operating Area These Devices are sensitive to Electrostatic Discharge. Proper Handing Procedures Should Be Followed. APT website – http://www.advancedpower.com 1-5 APTGT100TA60P All ratings @ Tj = 25°C unless otherwise specified Electrical Characteristics Symbol Characteristic ICES VCE(sat) VGE(th) IGES Zero Gate Voltage Collector Current Collector Emitter Saturation Voltage Gate Threshold Voltage Gate – Emitter Leakage Current Test Conditions VGE = 0 V, VCE = 600V Tj = 25°C VGE =15V IC = 100A Tj = 150°C VGE = VCE , IC = 1.5 mA VGE = 20V, VCE = 0 V Min Typ 1.5 1.7 5.8 Max 250 1.9 6.5 400 Unit µA V V nA 5.0 Dynamic Characteristics Symbol Cies Coes Cres Td(on) Tr Td(off) Tf Td(on) Tr Td(off) Tf Eon Eoff Characteristic Input Capacitance Output Capacitance Reverse Transfer Capacitance Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time Turn on Energy Turn off Energy Test Conditions VGE = 0 V VCE = 25V f = 1MHz Inductive Switching (25°C) VGE = ±15V VBus = 300V IC = 100A R G = 10Ω Inductive Switching (150°C) VGE = ±15V VBus = 300V IC = 100A R G = 10Ω Min Typ 6100 390 190 115 45 225 55 130 50 300 70 1.8 3.5 Max Unit pF ns ns mJ Reverse diode ratings and characteristics Symbol Characteristic VRRM Maximum Peak Repetitive Reverse Voltage IRM IF(A V) VF trr Qrr Maximum Reverse Leakage Current Maximum Average Forward Current Diode Forward Voltage Reverse Recovery Time Reverse Recovery Charge Test Conditions VR=600V 50% duty cycle Min 600 Tj = 25°C Tj = 150°C Tc = 80°C Tj = 25°C Tj = 150°C Tj = 25°C Tj = 150°C Tj = 25°C Tj = 150°C Typ Max 250 500 Unit V µA A IF = 100A VGE = 0 V IF = 100A VR = 300V di/dt =2000A/µs 100 1.6 1.5 125 220 4.7 9.9 2 V ns µC APTGT100TA60P – Rev 0 May, 2005 APT website – http://www.advancedpower.com 2-5 APTGT100TA60P Thermal and package characteristics Symbol Characteristic RthJC VISOL TJ TSTG TC Torque Wt Junction to Case Operating junction temperature range Storage Temperature Range Operating Case Temperature Mounting torque Package Weight IGBT Diode 2500 -40 -40 -40 3 Min Typ Max 0.44 0.77 175 125 100 5 250 Unit °C/W V °C N.m g RMS Isolation Voltage, any terminal to case t =1 min, I isol