96LEDK-A121XG50NE1

G121XN01 V0 ( V ) Preliminary Specifications ( ) Final Specifications Module 12.1 Inch Color TFT-LCD Model Name G121XN01 V0 Customer Date Approved by Debbie Chiu Checked & Approved by 2010/01/08 Prepared by Vivian Huang Note: This Specification is subject to change without notice. Date 2010/01/08 General Display Business Division / AU Optronics corporation G121XN01 V0 rev. 0.2 Page 1/24 G121XN01 V0 Contents 1. Operating Precautions .........................................................................................4 2. General Description .............................................................................................5 2.1 Display Characteristics ...................................................................................................... 5 2.2 Optical Characteristics....................................................................................................... 6 3. Functional Block Diagram ...................................................................................9 4. Absolute Maximum Ratings ..............................................................................10 4.1 Absolute Ratings of TFT LCD Module ............................................................................. 10 4.2 Absolute Ratings of Environment..................................................................................... 10 5. Electrical Characteristics ..................................................................................11 5.1 TFT LCD Module ............................................................................................................. 11 5.2 Backlight Unit................................................................................................................... 13 6. Signal Characteristics........................................................................................14 6.1 Pixel Format Image .......................................................................................................... 14 6.2 Scanning Direction........................................................................................................... 14 6.3 TFT-LCD Interface Signal Description ............................................................................. 15 6.4 The Input Data Format ..................................................................................................... 16 6.5 TFT-LCD Interface Timing................................................................................................ 17 6.6 Power ON/OFF Sequence ............................................................................................... 18 7. Connector & Pin Assignment............................................................................19 7.1 TFT-LCD Signal (CN1): LCD Connector.......................................................................... 19 7.2 LED Backlight Unit (CN2): Backlight Connector .............................................................. 19 8. Reliability Test Criteria.......................................................................................20 9. Mechanical Characteristics ...............................................................................21 9.1 LCM Outline Dimension (Front View) .............................................................................. 21 9.2 LCM Outline Dimension (Rear View)(Pin 1 position) ....................................................... 21 10. Label and Packaging........................................................................................23 10.1 Shipping Label (on the rear side of TFT-LCD display) .................................................. 23 10.2 Carton Package ............................................................................................................. 23 11 Safety..................................................................................................................24 11.1 Sharp Edge Requirements ............................................................................................. 24 11.2 Materials ........................................................................................................................ 24 11.3 Capacitors ...................................................................................................................... 24 11.4 National Test Lab Requirement...................................................................................... 24 G121XN01 V0 rev. 0.2 Page 2/24 G121XN01 V0 Record of Revision Version and Date Page Old description 0.0 2009/09/14 All First Edition 0.1 2009/12//11 21 22 16 LCM Outline Dimension (Front view) LCM Outline Dimension (Rear view) The input data format 0.2 2010/01/08 New Description Update mounting help position Update pin assignment Update SEL68 input data format G121XN01 V0 rev. 0.2 Page 3/24 G121XN01 V0 1. Operating Precautions 1) Since front polarizer is easily damaged, please be cautious and not to scratch it. 2) Be sure to turn off power supply when inserting or disconnecting from input connector. 3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or soft cloth. 5) Since the panel is made of glass, it may be broken or cracked if dropped or bumped on hard surface. 6) To avoid ESD (Electro Static Discharde) damage, be sure to ground yourself before handling TFT-LCD Module. 7) Do not open nor modify the module assembly. 8) Do not press the reflector sheet at the back of the module to any direction. 9) In case if a module has to be put back into the packing container slot after it was taken out from the container, do not press the center of the LED light bar edge. Instead, press at the far ends of the LED light bar edge softly. Otherwise the TFT Module may be damaged. 10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector of the TFT Module. 11) TFT-LCD Module is not allowed to be twisted & bent even force is added on module in a very short time. Please design your display product well to avoid external force applying to module by end-user directly. 12) Small amount of materials without flammability grade are used in the TFT-LCD module. The TFT-LCD module should be supplied by power complied with requirements of Limited Power Source (IEC60950 or UL1950), or be applied exemption. 13) Severe temperature condition may result in different luminance, response time and lamp ignition voltage. 14) Continuous operating TFT-LCD display under low temperature environment may accelerate lamp exhaustion and reduce luminance dramatically. 15) The data on this specification sheet is applicable when LCD module is placed in landscape position. 16) Continuous displaying fixed pattern may induce image sticking. It’s recommended to use screen saver or shuffle content periodically if fixed pattern is displayed on the screen. G121XN01 V0 rev. 0.2 Page 4/24 G121XN01 V0 2. General Description This specification applies to the Color Active Matrix Liquid Crystal Display G121XN01 V0 composed of a TFT-LCD display, a driver and power supply circuit, and a LED backlight system. The screen format is intended to support XGA (1024(H) x 768(V)) screen and 16.2M (RGB 8-bits) or 262k colors (RGB 6-bits). LED driving board for backlight unit is included in G121XN01 V0 and the LED unit is replaceable. All input signals are LVDS interface and compatible with G121SN01 V3 and G121SN01 V4. G121XN01 V0 designed with wide viewing angle; wide temperature and long life LED backlight is well suited for industial applications. G121XN01 V0 is a RoHS product. 2.1 Display Characteristics The following items are characteristics summary on the table under 25 ℃ condition: Items Unit Specifications Screen Diagonal [inch] 12.1 Active Area [mm] 245.76 (H) x 184.32 (V) Pixels H x V Pixel Pitch 1024 x 768 [mm] 0.24 x 0.24 Pixel Arrangement R.G.B.W Rectangle Display Mode TN, Normally White Nominal Input Voltage VDD [Volt] 3.3 (typ.) Typical Power Consumption [Watt] TBD All black pattern Weight [Grams] 495 (Max.) Physical Size [mm] 279.0(H) x 209.0(V) x 9.0(D) (Max.) Electrical Interface 1 channel LVDS Surface Treatment Anti-glare, Hardness 3H Support Color 16.2M / 262K colors Temperature Range Operating Storage (Non-Operating) RoHS Compliance o [ C] [oC] -30 to +80 -30 to +80 RoHS Compliance G121XN01 V0 rev. 0.2 Page 5/24 G121XN01 V0 2.2 Optical Characteristics The optical characteristics are measured under stable conditions at 25℃ (Room Temperature): Item Unit White Luminance [cd/m2] Uniformity % Conditions IF= 120mA/1 LED Line (center point) 5 Points Contrast Ratio Response Time Viewing Angle Typ. Max. Remark 375 500 - Note 1 75 - - Note 2, 3 500 700 - Note 4 [msec] Rising - 25 35 [msec] Falling - 10 20 [msec] Raising + Falling - 35 55 (Right) (Left) 70 80 - 70 80 - (Upper) (Lower) 70 80 - 70 80 - Red x TBD TBD TBD Red y TBD TBD TBD Green x TBD TBD TBD Green y TBD TBD TBD Blue x TBD TBD TBD Blue y TBD TBD TBD White x TBD 0.310 TBD White y TBD 0.330 TBD - 70 - [degree] [degree] Horizontal CR = 10 [degree] [degree] Vertical CR = 10 Color / Chromaticity Coordinates (CIE 1931) Color Gamut Min. % Note 5 Note 6 Note 1: Measurement method Equipment Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter (SR_3 or equivalent) Aperture 1∘with 50cm viewing distance Test Point Center Environment < 1 lux LCD Module SR_3 or equivalent Measuring distance Module Driving Equipment G121XN01 V0 rev. 0.2 Page 6/24 G121XN01 V0 Note 2: Definition of 5 points position (Display active area: 245.76mm (H) x 184.32mm (V)) W W /4 W /4 W /4 W /4 H /4 1 2 H /4 3 H H /4 4 5 H /4 Note 3: The luminance uniformity of 5 points is defined by dividing the minimum luminance values by the maximum test point luminance Minimum Brightness of five points δW9 = Maximum Brightness of five points Note 4: Definition of contrast ratio (CR): Contrast ratio (CR)= Brightness on the “White” state Brightness on the “Black” state Note 5: Definition of response time: The output signals of photo detector are measured when the input signals are changed from “White” to “Black” (falling time) and from “Black” to “White” (rising time), respectively. The response time interval is between 10% and 90% of amplitudes. Please refer to the figure as below. % Tf Tr 100 90 Optical White Black White response 10 0 Note 6: Definition of viewing angle Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180° horizontal an d 180° vertical range (off-normal viewing angles). Th e 180° viewing angle range is broken down as below: 90° ( θ) horizontal left and right, and 90° ( Φ) vertical high (up) and low (down). The measurement direction is typically perpendicular to the display surface with the screen rotated to its center to develop G121XN01 V0 rev. 0.2 Page 7/24 G121XN01 V0 the desired measurement viewing angle. G121XN01 V0 rev. 0.2 Page 8/24 G121XN01 V0 3. Functional Block Diagram The following diagram shows the functional block of the 12.1 inch color TFT/LCD module: G121XN01 V0 rev. 0.2 Page 9/24 G121XN01 V0 4. Absolute Maximum Ratings 4.1 Absolute Ratings of TFT LCD Module Item Symbol Min Max Unit Logic/LCD Drive Vin -0.3 +3.6 [Volt] 4.2 Absolute Ratings of Environment Item Symbol Min Max Unit Operating Temperature TOP -30 +80 [ C] Operation Humidity HOP 5 90 [%RH] Storage Temperature TST -30 +80 [oC] Storage Humidity HST 5 90 [%RH] o Note: Maximum Wet-Bulb should be 39℃ and no condensation. G121XN01 V0 rev. 0.2 Page 10/24 G121XN01 V0 5. Electrical Characteristics 5.1 TFT LCD Module 5.1.1 Power Specification Symbol Parameter Min Typ Max Units VDD Logic/LCD Input Voltage 3.0 3.3 3.6 [Volt] IVDD LCD Input Current - TBD - [mA] VDD=3.3V at 60 HZ, all Black Pattern PVDD LCD Power comsumption - TBD - [Watt] VDD=3.3V at 60 HZ, all Black Pattern Irush LCD LCD Inrush Current - - TBD [A] - - TBD Allowable Logic/LCD Drive Ripple Voltage VDDrp Remark Note 1; VDD=3.3V Black Pattern, Rising time=470us [mV] p-p VDD=3.3V at 60 HZ, all Black Pattern Note 1: Measurement condition: +3.3V Q3 AO6402 D6 D5 D2 D1 F1 S VCC VDD (LCD Module Input) G R1 47K (High to Low) Control Signal D1 D2 D5 D6 C1 1uF/16V Q3 AO6402 R2 S G 1K 2 C3 +12.0V SW1 1 SW MAG-SPST VR1 R2 0.01uF/25V 47K 1K C2 1uF/25V 3.3V 90% 10% 0V 470 us VDD rising time G121XN01 V0 rev. 0.2 Page 11/24 G121XN01 V0 5.1.2 Signal Electrical Characteristics Input signals shall be low or Hi-Z state when VDD is off. Symbol Item Min. Typ. Max. Unit Remark VTH Differential Input High Threshold - - 100 [mV] VCM=1.2V VTL Differential Input Low Threshold 100 - - [mV] VCM=1.2V Input Differential Voltage 100 400 600 [mV] Differential Input Common Mode Voltage 1.1 - 1.45 [V] ｜VID｜ ｜ VICM VTH/VTL=+-100mV Note: LVDS Signal Waveform. G121XN01 V0 rev. 0.2 Page 12/24 G121XN01 V0 5.2 Backlight Unit 5.2.1 Parameter guideline for LCD Following characteristics are measured under a stable condition using a inverter at 25℃. (Room Temperature): Symbol Parameter Min. Typ. Max. Unit VCC Input Voltage 10.8 12 12.6 [Volt] IVCC Input Current - TBD - [A] 100% PWM Duty PVCC Power Consumption - TBD TBD [Watt] 100% PWM Duty Irush LED Inrush Current - - TBD [A] FPWM Dimming Frequency 200 - 20K [Hz] Swing Voltage 3 3.3 5.5 [Volt] Dimming duty cycle 5 - 100 % LED Forward Current - 120 - [mA] Ta = 25oC - TBD TBD [Volt] IF = 120mA, Ta = -30oC - TBD TBD [Volt] IF = 120mA, Ta = 25oC - TBD TBD [Volt] IF = 120mA, Ta = 85oC - TBD TBD [Watt] 50,000 - - Hrs IF VF PLED LED Forward Voltage LED Power Consumption Operation Life Remark at rising time=470us IF=120mA, Ta= 25oC Note 1: Ta means ambient temperature of TFT-LCD module. Note 2: VCC, IVCC, Irush LED, PVCC are defined for LED backlight.(100% duty of PWM dimming) Note 3: IF, VF are defined for one channel LED. There are two LED channel in back light unit. Note 4: If G121XN01 V0 module is driven by high current or at high ambient temperature & humidity condition. The operating life will be reduced. Note 5: Operating life means brightness goes down to 50% initial brightness. Minimum operating life time is estimated data. G121XN01 V0 rev. 0.2 Page 13/24 G121XN01 V0 6. Signal Characteristics 6.1 Pixel Format Image Following figure shows the relationship between input signal and LCD pixel format. st nd 1 Pixel 1st th 2 th 1023 Pixel 1024 Pixel Pixel R G B R G B R G B R G B R G B R G B R G B R G B Line 768th Lin 6.2 Scanning Direction The following figures show the image seen from the front view. The arrow indicates the direction of scan. Fig. 1 Normal scan (Pin19, RSV = Low or NC) Fig. 2 Reverse scan (Pin19, RSV = High or VDD) G121XN01 V0 rev. 0.2 Page 14/24 G121XN01 V0 6.3 TFT-LCD Interface Signal Description The module using a LVDS receiver embaded in AUO’s ASIC. LVDS is a differential signal technology for LCD interface and a high-speed data transfer device. Input Signal Interface Pin No. Symbol 1 VDD Power Supply, 3.3V (typical) 2 VDD Power Supply, 3.3V (typical) 3 GND Ground 4 SEL68 6/ 8bits LVDS data input selection [H: 8bits L/NC: 6bit] 5 RIN0- LVDS receiver signal channel 0 6 RIN0+ LVDS Differential Data Input (R0, R1, R2, R3, R4, R5, G0) 7 GND 8 RIN1- Ground LVDS receiver signal channel 1 9 RIN1+ LVDS Differential Data Input (G1, G2, G3, G4, G5, B0, B1) 10 GND Ground 11 RIN2- LVDS receiver signal channel 2 12 RIN2+ LVDS Differential Data Input (B2, B3, B4, B5, HS, VS, DE) 13 GND 14 CLKIN- 15 CLKIN+ 16 GND Ground 17 RIN3- LVDS receiver signal channel 3, NC for 6 bit LVDS Input 18 RIN3+ LVDS Differential Data Input (R6, R7, G6, G7, B6, B7, RSV) 19 RSV 20 Description Ground LVDS receiver signal clock Reverse Scan Function [H: Enable; L/NC: Disable] NC/GND Reserved for AUO internal test. Please treat it as NC. Note 1: Input Signals shall be in low status when VDD is off. Note 2: High stands for “3.3V”, Low stands for “0V”, NC stands for “No Connection”. Note 3: RSV stands for “Reserved”. G121XN01 V0 rev. 0.2 Page 15/24 G121XN01 V0 6.4 The Input Data Format 6.4.1 SEL68 SEL68 =“Low” or “NC” for 6 bits LVDS Input SEL68 = “High” for 8 bits LVDS Input Note1: Please follow PSWG. Note2: R/G/B data 7:MSB, R/G/B data 0:LSB Signal Name Description +RED5(R5) Red Data 5 (MSB) Red-pixel Data +RED4(R4) Red Data 4 Each red pixel’s brightness data consists of these +RED3(R3) Red Data 3 6 bits pixel data. +RED2(R2) Red Data 2 +RED1(R1) Red Data 1 +RED0(R0) Red Data 0 (LSB) Red-pixel Data +GREEN5(G5) Green Data 5 (MSB) Green-pixel Data +GREEN4(G4) Green Data 4 Each green pixel’s brightness data consists of these +GREEN3(G3) Green Data 3 6 bits pixel data. +GREEN2(G2) Green Data 2 +GREEN1(G1) Green Data 1 +GREEN0(G0) Green Data 0 (LSB) Green-pixel Data +BLUE5(B5) Blue Data 5 (MSB) Blue-pixel Data +BLUE4(B4) Blue Data 4 Each blue pixel’s brightness data consists of these +BLUE3(B3) Blue Data 3 6 bits pixel data. Blue Data 2 +BLUE2(B2) +BLUE1(B1) Blue Data 1 Blue Data 0 (LSB) +BLUE0(B0) Blue-pixel Data CLK Data Clock The typical frequency is 40MHz. The signal is used to strobe the pixel data and DE signals. All pixel data shall be valid at the falling edge when the DE signal is high. DE Display Timing This signal is strobed at the falling edge of CLK. When the signal is high, the pixel data shall be valid to be displayed. Note: Output signals from any system shall be low or Hi-Z state when VDD is off. G121XN01 V0 rev. 0.2 Page 16/24 G121XN01 V0 6.5 TFT-LCD Interface Timing 6.5.1 Timing Characteristics Signal Symbol Min. Typ. Max. Unit Clock Frequency 1/ TClock 50 65 80 MHz Period TV 776 806 1023 Active TVD - 768 - Blanking TVB 8 38 255 Period TH 1054 1344 2047 Active THD - 1024 - THB 40 320 1023 Vertical Section Horizontal Section Blanking Note 1: Frame rate is 60 Hz. Note 2: DE mode. TLine TClock 6.5.2 Input Timing Diagram G121XN01 V0 rev. 0.2 Page 17/24 G121XN01 V0 6.6 Power ON/OFF Sequence VDD power and lamp on/off sequence is as below. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when VDD is off. Power ON/OFF sequence timing Value Parameter Units Min. Typ. Max. T1 0.5 - 10 [ms] T2 30 40 50 [ms] T3 200 - - [ms] T4 10 - - [ms] T5 10 - - [ms] T6 0 - - [ms] T7 10 - - [ms] T8 100 - - [ms] T9 0 16 50 [ms] T10 - - 10 [ms] T11 1000 - - [ms] The above on/off sequence should be applied to avoid abnormal function in the display. Please make sure to turn off the power when you plug the cable into the input connector or pull the cable out of the connector. G121XN01 V0 rev. 0.2 Page 18/24 G121XN01 V0 7. Connector & Pin Assignment Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components. 7.1 TFT-LCD Signal (CN1): LCD Connector Connector Name / Designation Manufacturer Signal Connector STM or compatible Connector Model Number MSB240420-E or compatible Adaptable Plug P240420 or compatible Pin No. 1 3 5 7 9 11 13 15 17 19 Symbol VDD GND RIN0GND RIN1+ RIN2GND CLKIN+ RIN3RSV Pin No. 2 4 6 8 10 12 14 16 18 20 Symbol VDD SEL68 RIN0+ RIN1GND RIN2+ CLKINGND RIN3+ NC/GND 7.2 LED Backlight Unit (CN2): Driver Connector Connector Name / Designation Lamp Connector Manufacturer ENTERY or compatible Connector Model Number 3808K-F05N-02R or compatible Mating Model Number H208K–P05N-02B or compatible Pin No. Pin1 Pin2 Pin3 Pin4 Pin5 symbol VCC GND On/OFF Dimming NA description 12V input GND 5V-ON,0V-OFF PWM 7.3 LED Backlight Unit (CN4): Light bar Connector Connector Name / Designation Lamp Connector Manufacturer ENTERY or compatible Connector Model Number H208K–P03N-02B or compatible Mating Model Number(CN3) 3808K-F03N-02R or compatible Pin No. Pin1 Pin2 Pin3 symbol H L L description LED anode LED cathode LED cathode Color Red White Black G121XN01 V0 rev. 0.2 Page 19/24 G121XN01 V0 8. Reliability Test Criteria Items Required Condition Temperature Humidity Bias 40℃, 90%RH, 300 hours Note High Temperature Operation 80℃, 300 hours Low Temperature Operation -30℃, 300 hours Hot Storage 80℃, 300 hours Cold Storage -30℃, 300 hours Thermal Shock Test -20℃/ 30 min, 60℃/ 30 min, 100cycles, Hot Start Test 80℃/ 1Hr min. power on/off per 5 minutes, 5 times Cold Start Test -30℃/ 1Hr min. power on/off per 5 minutes, 5 times 40℃ minimun ramp rate Shock Test (Non-Operating) 50G, 20ms, Half-sine wave, ( ±X, ±Y, ±Z) Vibration Test (Non-Operating) 1.5G, (10~200Hz, Sine wave) On/off test On/10 sec, Off/10 sec, 30,000 cycles 30 mins/axis, 3 direction (X, Y, Z) Contact Discharge: ± 8KV, 150pF(330Ω ) 1sec, 8 points, 25 times/ ESD Note 1 point Air Discharge: ± 15KV, 150pF(330Ω ) 1sec, 8 points, 25 times/ point EMI 30-230 MHz, limit 30 dBu V/m, 230-1000 MHz, limit 37 dBu V/m Note1: According to EN61000-4-2, ESD class B: Some performance degradation allowed. No data lost Self-recoverable. No hardware failures. Note2:
Water condensation is not allowed for each test items.
Each test is done by new TFT-LCD module. Don’t use the same TFT-LCD module repeatedly for reliability test.
The reliability test is performed only to examine the TFT-LCD module capability.
To inspect TFT-LCD module after reliability test, please store it at room temperature and room humidity for 24 hours at least in advance. G121XN01 V0 rev. 0.2 Page 20/24 G121XN01 V0 9. Mechanical Characteristics 9.1 LCM Outline Dimension (Front View) G121XN01 V0 rev. 0.2 Page 21/24 G121XN01 V0 9.2 LCM Outline Dimension (Rear View) G121XN01 V0 rev. 0.2 Page 22/24 G121XN01 V0 10. Label and Packaging 10.1 Shipping Label (on the rear side of TFT-LCD display) TBD 10.2 Carton Package TBD G121XN01 V0 rev. 0.2 Page 23/24 G121XN01 V0 11 Safety 11.1 Sharp Edge Requirements There will be no sharp edges or comers on the display assembly that could cause injury. 11.2 Materials 11.2.1 Toxicity There will be no carcinogenic materials used anywhere in the display module. If toxic materials are used, they will be reviewed and approved by the responsible AUO toxicologist. 11.2.2 Flammability All components including electrical components that do not meet the flammability grade UL94-V1 in the module will complete the flammability rating exception approval process. The printed circuit board will be made from material rated 94-V1 or better. The actual UL flammability rating will be printed on the printed circuit board. 11.3 Capacitors If any polarized capacitors are used in the display assembly, provisions will be made to keep them from being inserted backwards. 11.4 National Test Lab Requirement The display module will satisfy all requirements for compliance to: UL 1950, First Edition U.S.A. Information Technology Equipment G121XN01 V0 rev. 0.2 Page 24/24