AM10TW-2412D-NZ

Click on Series name for product info on aimtec.com Series AM10TW-NZ 10 Watt | DC-DC Converter FEATURES: • • • • • • Ultra-Wide 4:1 input range • Operating temperature -40oC to + 85oC Efficiency up to 88% • Remote on/off control Low power consumption 0.12W • Input/Output Isolation 1500VDC Continuous short circuit protection • Over voltage & over current protection Meet EN55032 Class A with no external component needed Design to meet EN62368 and EN50155 Models Single output Model Input Voltage (V) Output Voltage (Vdc) Output Current max (mA) Isolation (VDC) 9-36 9-36 9-36 9-36 9-36 18-75 18-75 18-75 18-75 18-75 3.3 5 12 15 24 3.3 5 12 15 24 2400 2000 833 667 416 2400 2000 833 667 416 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1200 1000 470 330 100 1200 1000 470 330 100 87 88 87 87 88 86 87 87 87 88 Input Voltage (V) Output Voltage (V) Output Current max (mA) Isolation (VDC) Max Capacitive Load(uF) Efficiency (%) AM10TW-2403S-NZ AM10TW-2405S-NZ AM10TW-2412S-NZ AM10TW-2415S-NZ AM10TW-2424S-NZ AM10TW-4803S-NZ AM10TW-4805S-NZ AM10TW-4812S-NZ AM10TW-4815S-NZ AM10TW-4824S-NZ Max Capacitive Load (uF) Efficiency (%) Models Dual output Model AM10TW-2405D-NZ 9-36 ±5 ±1000 1500 ±1000 83 AM10TW-2412D-NZ 9-36 ±12 ±416 1500 ±470 87 AM10TW-2415D-NZ 9-36 ±15 ±330 1500 ±330 87 AM10TW-4805D-NZ 18-75 ±5 ±1000 1500 ±1000 83 AM10TW-4812D-NZ 18-75 ±12 ±416 1500 ±470 87 AM10TW-4815D-NZ 18-75 ±15 ±330 1500 ±330 87 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity1 000 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25°C) 1.5mm from case for 10 sec 300 g °C Environment Specifications Test Parameters Conditions Vibration EN50155 EN62368 IEC/EN 61373 Category 1, class B 10-150Hz, 5g, every axis tested Safety Specifications Parameters Agency approvals CE, UL pending EMI - Conducted and radiated emission Standards Electrostatic Discharge Immunity RF, Electromagnetic Field Immunity www.aimtec.com F 051e R1.A REV:07/20/A CISPR32 / EN55032 Class A, without external circuit CISPR32 / EN55032 Class B, with the EMC recommended circuit part B EN50121-3-2, with the EMC recommended circuit part B EN55016-2-1, with the EMC recommended circuit part B IEC61000-4-2, Contact ±4kV, Criteria B EN50121-3-2, Contact ±6kV/ Air ±8kV, Criteria B IEC61000-4-3, 10V/m, Criteria A EN50121-3-2, 20V/m, Criteria A Tel: +1 514 620 2722 2 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10TW-NZ 10 Watt | DC-DC Converter Electrical Fast Transient/ Burst Immunity Surge Immunity RF, Conducted Disturbance Immunity Voltage dips, short interruptions, and voltage variations immunity IEC61000-4-4, ±2kV with the EMC recommended circuit part A, Criteria B EN50121-3-2, ±2kV with the EMC recommended circuit part A, Criteria A IEC61000-4-5, L-L ±2KV with the EMC recommended circuit part A, Criteria B EN50121-3-2, L-L ±1KV with the EMC recommended circuit part A, Criteria A IEC61000-4-6, 10Vrms, Criteria A EN50121-3-2, 10Vrms, Criteria A IEC61000-4-29, 0%-70%, Criteria B Derating Free Air Convection ±5V output 100 Others output 80 Safe Operating Area 60 40 20 0 0 - 40 - 20 20 65 71 40 60 85 80 100 Ambient Temperature º C Dimensions Pin Out Specifications 22.86 (0.90) 0.50 (0.02) 20.00 (0.79) 1 2 3 9 Bottom View 23 22 16 Pin Single Dual 1 2 3 9 11 14 16 22 23 Remote On/Off -V Input -V Input No Pin N.C. +V Output -V Output +V Input +V Input Remote On/Off -V Input -V Input Common -V Output +V Output Common +V Input +V Input 11 15.24 (0.60) 32.00 (1.26) 14 2.54 (0.10) 5.08 (0.20) Printed Face 4.10 (0.16) 10.80 (0.43) All dimensions are typical: millimeters (inches) Pin Diameter: 0.50 ± 0.1 (0.02 ± 0.004) General Tolerance: ± 0.5 (±0.02) Typical application circuit Single output models + Vin + Vin + Vout + Cin - Vin DC www.aimtec.com F 051e R1.A REV:07/20/A DC +Vout + Vin Cin 100µF 10-47µF - Vout + Vin + Vout +Vout + Cout + + Cin Cout - Vin Vin 24V 48V Dual output models DC DC Common + Cout - Vout - Vin - Vin - Vout - Vout Cout 10µF 10µF Tel: +1 514 620 2722 3 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10TW-NZ 10 Watt | DC-DC Converter EMC Recommended Circuit For 3.3V/5V single output models CY1 1nF/2KV LCM 1.4~1.7mH FUSE + Vin + Vin + + C1 C2 C3 C4 DC - Vin - Vin DC Cout - Vout - Vout + Vout +Vout CY2 1nF/2KV B A +Vout + Vout For other models LDM 10uH FUSE CY1 1nF/2KV + Vin + Vin + + C1 C2 C3 C4 DC - Vin - Vin B A DC - Vout Cout - Vout CY2 1nF/2KV Part A for EMS. Part B for EMI. Model FUSE C1, C4 C2, C3 24V 48V Choose based on actual current 330µF/50V 330µF/100V 10µF/50V 10µF/100V NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity