AM50E-2424S-NZ-K

Series AM50E-NZ 50 Watt | DC-DC Converter FEATURES: • • • • Wide Input range 2:1 High Efficiency up to 93% Remote On/Off Control Trim Adjustment • • • • Input to Output Isolation of 1500VDC Input Over Voltage and Under Voltage Lockout Output OVP, OCP & SCP Operating Temperature -40 to +85°C Models Single output Model Input Voltage (VDC) Output Voltage (VDC) Output Current max (A) Full load/No load Input Current (mA) Max Capacitive Load(uF) Efficiency (%) AM50E-2403S-NZ 18-36 3.3 10 1545/55 27000 91 AM50E-2405S-NZ 18-36 5 10 2341/105 18900 91 AM50E-2412S-NZ 18-36 12 4.167 2290/105 3700 93 AM50E-2415S-NZ 18-36 15 3.333 2290/105 2000 93 AM50E-2424S-NZ 18-36 24 2.083 2341/65 1000 91 AM50E-4805S-NZ 36-75 5 10 1171/55 18900 91 AM50E-4812S-NZ 36-75 12 4.167 1145/55 3700 93 AM50E-4815S-NZ 36-75 15 3.333 1145/70 2000 93 AM50E-4824S-NZ 36-75 24 2.083 1158/50 1000 92 *Add suffix “-ST” for optional screw terminal bottom plate or “-STD” for optional DIN Rail screw terminal bottom plate. **Add suffix “-K” for optional heatsink, “-K-ST” for optional heatsink and screw terminal bottom plate or “-K-STD” for optional heatsink and DIN Rail screw terminal bottom plate. The AM50E-NZ series will be discontinued (EOL) by December 30, 2020; for new designs, please refer to AM50E-Z series. NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity1000 2000 1500 VDC MOhm pF Tel: +1 514 620 2722 1 of 8 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM50E-NZ 50 Watt | DC-DC Converter Output Specifications Parameters Conditions Voltage accuracy Maximum Units ±1 ±3 3.9 6.2 15 18 30 % 3.3V output 5V output 12V output 15V output 24V output Over voltage protection* Over current protection Short Circuit protection Short circuit restart Line voltage regulation Load voltage regulation Temperature coefficient Ripple & Noise Typical 135 Hiccup, continuous Auto-restart ±0.2 ±0.5 LL-HL 10-100% load 3.3V/5V Vout AM50E-4824S-NZ Ohters Conditions Typical 100% load See derating curve 300 24V Vout Others 25% load step Transient recovery deviation *Restart needed to function properly ±0.5 ±1 ±0.03 250 350 300 25% load step Voltage adjustment range Transient recovery time % 100 200 200 ±10 500 200 ±3 20MHz Bandwidth VDC % of Vin % %/oC mV p-p % 1000 500 ±5 µS % General Specifications Parameters Switching frequency Operating temperature Storage temperature Maximum case temperature Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF Maximum soldering temperature Maximum Units 105 KHz o C o C o C 95 % RH -40 to +85 -55 to +125 Free Air Convection Aluminum alloy Pin mountable 35 With optional -ST mounting plate 57 With optional -STD mounting plate 77 g With optional -K Pin mountable 43 With optional -ST-K mounting plate 65 With optional -STD-K mounting plate 85 Pin mountable 2.00 x 1.00 x 0.46inches 50.80 x 25.40 x 11.80mm With optional -ST mounting plate 2.99 x 1.24 x 0.84inches 76.00 x 31.50 x 21.20mm With optional -STD mounting plate 2.99 x 1.24 x 1.02inches 76.00 x 31.50 x 25.80mm With optional -K Pin mountable 2.02 x 1.03 x 0.65inches 51.40 x 26.20 x 16.50mm With optional -ST-K mounting plate 2.99 x 1.24 x 1.00inches 76.00 x 31.50 x 25.30mm With optional -STD-K mounting plate 2.99 x 1.24 x 1.18inches 76.00 x 31.50 x 29.90mm >1 000 000 hrs (MIL-HDBK-217 F at +25 °C) o 10sec, 1.5mm from case 300 C Environmental Specifications Parameters Vibration Test mode Acceleration Converter operation www.aimtec.com F 051e R15 REV: 04/20/A 10-55Hz 10G, 30min one cycle, every axis tested Before and after test, body mounted (on chassis) Tel: +1 514 620 2722 2 of 8 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM50E-NZ 50 Watt | DC-DC Converter Safety Specifications Parameters Approval UL (AM50E-4812S-NZ only) Information Technology Equipment Electrostatic Discharge Immunity RF, Electromagnetic Field Immunity Electrical Fast Transient / Burst Immunity Surge Immunity RF, Conducted Disturbance Immunity Standards UL60950-1 CISPR32/EN55032 Class B, with the EMC recommended circuit IEC 61000-4-2, Contact ±4KV, Criteria B IEC 61000-4-3, 10V/m, Criteria A IEC 61000-4-4, ±2KV, Criteria B, with the EMC recommended circuit IEC 61000-4-5, L-L ±2KV, Criteria B, with the EMC recommended circuit IEC 61000-4-6, 3 Vrms, Criteria A Pin Out Specifications 50.80 (2.00) 2 5 1 4 45.72 (1.80) 2.54 10.16 (0.10) (0.40) Top View 6 3 7.62 (0.30) 25.40 (1.00) 2.54 (0.10) 5.08 (0.20) Bottom View 10.16 2.54 (0.40) (0.10) Dimensions Pin 1 2 3 4 5 6 Single On/Off Control -Vin +Vin Trim -Vout +Vout 11.80 (0.47) Printed Face Note: Unit: mm (inch) General tolerances: ±0.50 (±0.02) Side View 4.10 (0.16) 1.00 (0.04) Heatsink Option: AM50E-NZ-K Top View 51.40 (2.02) 6 10.16 (0.40) 3 2 5 10.16 (0.40) 7.62 (0.30) 26.20 (1.03) 2.54 (0.10) 5.08 (0.20) Bottom View 1 4 16.50 (0.65) 45.72 (1.80) www.aimtec.com 4.10 (0.16) 1.00 (0.04) F 051e R15 REV: 04/20/A Note: Unit: mm (inch) General tolerances: ±0.50 (±0.02) Side View Tel: +1 514 620 2722 3 of 8 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM50E-NZ 50 Watt | DC-DC Converter Screw Terminal Option: AM50E-NZ-ST 76.00 (2.99) 61.60 (2.43) 23.00 (0.91) Ø3.30 31.50 (1.24) Pin Out Specifications 1 2 3 Top View 4 5 6 Pin Single 1 2 3 4 5 6 On/Off Control -Vin +Vin Trim - Vout + Vout Side View 8.80 (0.35) 21.20 (0.84) Ø3.30 Note: Unit: mm (inch) Wire range: 24-12 AWG Tightening torque: Max 0.4 N*m General tolerances: ±0.50 (±0.02) Screw Terminal with Heatsink Option: AM50E-NZ-K-ST Top View 76.00 (2.99) 61.60 (2.43) 23.00 (0.91) 31.50 (1.24) Ø3.30 1 2 3 4 5 6 www.aimtec.com F 051e R15 REV: 04/20/A Side View 8.80 (0.35) 25.30 (1.00) 21.20 (0.84) Ø3.30 Tel: +1 514 620 2722 4 of 8 Note: Unit: mm (inch) Wire range: 24-12 AWG Tightening torque: Max 0.4 N*m General tolerances: ±0.50 (±0.02) Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM50E-NZ 50 Watt | DC-DC Converter DIN-RAIL Option: AM50E-NZ-K-STD 76.00 (2.99) 61.60 (2.43) 23.00 (0.91) Ø3.30 31.50 (1.24) Pin Out Specifications 1 2 3 4 5 6 Top View Pin Single 1 2 3 4 5 6 On/Off Control -Vin +Vin Trim - Vout + Vout Side View 9.80 (0.39) 22.20 (0.87) 25.80 (1.00) Ø3.30 Note: Unit: mm (inch) Mounting rail: TS35 Wire range: 24-12 AWG Tightening torque: Max 0.4 N*m General tolerances: ±0.50 (±0.02) DIN-RAIL with heatsink Option: AM50E-NZ-K-STD Top View 76.00 (2.99) 61.60 (2.43) 23.00 (0.91) 31.50 (1.24) Ø3.30 1 2 3 4 5 6 www.aimtec.com F 051e R15 REV: 04/20/A Side View 9.80 (0.39) 25.80 (1.00) 29.90 (1.18) 22.20 (0.87) Ø3.30 Tel: +1 514 620 2722 5 of 8 Note: Unit: mm (inch) Mounting rail: TS35 Wire range: 24-12 AWG Tightening torque: Max 0.4 N*m General tolerances: ±0.50 (±0.02) Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM50E-NZ 50 Watt | DC-DC Converter Derating For 3.3 & 5V output models For 12, 15 & 24V output models Free Air Convection Free Air Convection Without heatsink Without heatsink 100 With heatsink 80 Output Power (%) Output Power (%) 100 Safe Operating Area 60 40 With heatsink 80 Safe Operating Area 60 40 20 20 0 - 20 - 40 0 20 40 55 65 60 85 80 0 100 - 20 - 40 0 Ambient Temperature º C 20 40 60 70 85 80 100 Ambient Temperature º C Typical Application Circuit + Vin C1 100uF + Vin Model C2 +Vout + Vout + Vin DC + DC - Vin C2 - Vout - Vout Single output models 3.3V/5V Vout 12V/15V Vout 470µF 100µF 24V Vout 47µF EMC Recommended Circuit CY1 3.3nF/250VAC LCM 2.2mH FUSE + Vin MOV - Vin + + C1 C2 C3 +Vout + Vout + Vin DC DC - Vin - Vout C4 - Vout CY2 3.3nF/250VAC www.aimtec.com F 051e R15 REV: 04/20/A Tel: +1 514 620 2722 6 of 8 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM50E-NZ 50 Watt | DC-DC Converter Model FUSE MOV C1 C2 C3 C4 24V Vin 48V Vin Choose based on actual input current S20K30 S14K60 680µF/50V 330µF/100V 330µF/50V 330µF /100V 4.7µF/50V 2.2µF/100V Refer to the C2 in typical application circuit Trimming Output voltage can be externally trimmed by utilizing the methods as shown below Fixed Resistor Variable Potentiometer Leave open if not used. AM50E-xx03S-NZ Trim down % 1 Vout (VDC) 3.27 Rt down (KΩ) 236.27 Trim up % 1 Vout (VDC) 3.33 Rt up (KΩ) 263.512 2 3.23 106.095 2 3.37 81.826 3 3.20 71.347 3 3.40 50.017 4 3.17 51.633 4 3.43 33.939 5 3.14 38.931 5 3.47 21.804 6 3.10 27.676 6 3.50 16.033 7 3.07 21.71 7 3.53 11.826 8 3.04 17.076 8 3.56 8.624 9 3.00 12.299 9 3.60 5.38 10 2.97 9.457 10 3.63 3.447 AM50E-xx05S-NZ Trim down % 1 Vout (VDC) 4.95 Rt down (KΩ) 128.53 Trim up % 1 Vout (VDC) 5.05 Rt up (KΩ) 131.399 2 4.9 56.78 2 5.1 59.65 3 4.85 32.863 3 5.15 35.733 4 4.8 20.905 4 5.2 23.775 5 4.75 13.73 5 5.25 16.6 6 4.7 8.947 6 5.3 11.817 7 4.65 5.53 7 5.35 8.4 8 4.6 2.968 8 5.4 5.838 9 4.55 0.974 9 5.45 3.844 10 4.5 -0.62 10 5.5 2.25 www.aimtec.com F 051e R15 REV: 04/20/A Tel: +1 514 620 2722 7 of 8 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM50E-NZ 50 Watt | DC-DC Converter AM50E-xx12S-NZ Trim down % 1 2 3 4 5 6 7 8 9 10 11.88 11.76 11.64 11.52 11.4 11.28 11.16 11.04 10.92 10.8 489.091 294.452 205.527 154.585 121.573 98.442 81.332 68.164 57.716 49.223 1 2 3 4 5 6 7 8 9 10 12.12 12.24 12.36 12.48 12.6 12.72 12.84 12.96 13.08 13.2 699.444 151.922 76.879 47.075 31.077 21.095 14.274 9.317 5.552 2.595 6 14.1 171.333 6 15.9 19.667 7 13.95 141.571 7 16.05 13.714 8 9 13.8 13.65 119.25 101.889 8 9 16.2 16.35 9.25 5.778 10 13.5 88 10 16.5 3 Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) AM50E-xx15S-NZ Trim down % Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) AM50E-xx24S-NZ Trim down % Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 1 14.85 1213 1 15.15 228 2 14.7 588 2 15.3 103.001 3 14.55 379.667 3 15.45 61.333 1 23.76 1038.04 8 1 24.24 2 23.52 638.01 5 2 24.48 143.11 6 3 23.28 455.25 6 3 24.72 4 23.04 350.55 3 4 24.96 5 22.8 282.70 2 5 25.2 6 22.56 235.15 9 6 25.44 7 22.32 199.99 3 7 25.68 8 22.08 172.92 8 8 25.92 9 21.84 151.45 3 9 26.16 10 21.6 133.99 9 10 26.4 74.892 47.797 33.252 24.178 17.977 13.47 10.047 7.359 640.98 4 14.4 275.5 4 15.6 40.5 5 14.25 213 5 15.75 28 NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity