A2557SEB

2557 A2557xLB (SOIC) OUT1 K OUT2 GROUND GROUND OUT3 FAULT OUT4 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 IN 1 IN2 ENABLE GROUND GROUND V CC IN 3 IN 4 PROTECTED QUAD LOW-SIDE DRIVER WITH FAULT DETECTION & SLEEP MODE The A2557xB, A2557xEB, and A2557xLB have been specifically designed to provide cost-effective solutions to relay-driving applications with up to 300 mA drive current per channel. They may also be used for driving incandescent lamps in applications where turn-on time is not a concern. Each of the four outputs will sink 300 mA in the on state. The outputs have a minimum breakdown voltage of 60 V and a sustaining voltage of 40 V. A low-power Sleep Mode is activated with either ENABLE low or all inputs low. In this mode, the supply current drops to below 100 µA. Over-current protection for each channel has been designed into these devices and is activated at a nominal 500 mA. It protects each output from short circuits with supply voltages up to 32 V. When an output experiences a short circuit, the output current is limited at the 500 mA current clamp. In addition, foldback circuitry decreases the current limit if an excessive voltage is present across the output and assists in keeping the device within its SOA (safe operating area). An exclusive-OR circuit compares the input and output state of each driver. If either a short or open load condition is detected, a single FAULT output is turned on (active low). Similar devices, for operation to 1.3 A, are available as the UDx2547B/EB. Continuous or multiple overload conditions causing the channel temperature to reach approximately 165°C will result in an additional linear decrease in the output current of the affected driver. If the fault condition is corrected, the output stage will return to its normal saturated condition. The first character of the part number suffix determines the device operating temperature range. Suffix ‘S-’ is the standard -20°C to +85°C; suffix ‘E-’ is -40°C to +85°C; suffix ‘K-’ is for the industrial temperature range of -40°C to +125°C. Package suffix ‘-B’ devices are 16-pin power DIPs; suffix ‘-EB’ devices are 28-lead power PLCCs; and suffix ‘-LB’ are 16lead power wide-body SOICs for surface-mount applications. All packages are of batwing construction to provide for maximum package power dissipation. Data Sheet 29317.16F Dwg. PP-017-4 Note that the A2557xB (DIP) and the A2557xLB (SOIC) are electrically identical and share a common terminal number assignment. ABSOLUTE MAXIMUM RATINGS Output Voltage, VO .............................. 60 V Over-Current Protected Output Voltage, VO ..................................................... 32 V Output Current, IO ......................... 500 mA* FAULT Output Voltage, VFLT ............. 60 V Logic Supply Voltage, VCC ................. 7.0 V Input Voltage, VI or VOE ..................... 7.0 V Package Power Dissipation, PD ........................................... See Graph Operating Temperature Range, TA Suffix ‘S-’ ...................... -20°C to +85°C Suffix ‘E-’ ...................... -40°C to +85°C Suffix ‘K-’ ................... -40°C to +125°C Junction Temperature, TJ ............................................... +150°C* Storage Temperature Range, TS ................................. -55°C to +150°C *Outputs are current limited at approximately 500 mA per driver and junction temperature limited if higher current is attempted. FEATURES s 300 mA Output Current per Channel s Independent Over-Current Protection &Thermal Limiting for Each Driver s Output Voltage to 60 V s Output SOA Protection s Fault-Detection Circuitry for Open or Shorted Load s Low Quiescent Current Sleep Mode s Integral Output Flyback/Clamp Diodes s TTL- and 5 V CMOS-Compatible Inputs Complete part number includes a suffix to identify operating temperature range (E-, K-, or S-) and package type (-B, -EB, or -LB). Always order by complete part number, e.g., A2557KLB . 2557 PROTECTED QUAD DRIVER WITH FAULT DETECTION & SLEEP MODE FUNCTIONAL BLOCK DIAGRAM FAULT ENABLE SLEEP CONTROL 60 µA K COMMON CONTROL ONE OF FOUR DRIVERS V CC – + 2.5 V OUTN IN N THERMAL LIMIT CURRENT LIMIT 30 µA