UDN2916EB-T

2916 Dual Full-Bridge PWM Motor Driver Discontinued Product This device is no longer in production. The device should not be purchased for new design applications. Samples are no longer available. Date of status change: January 30, 2012 Recommended Substitutions: For existing customer transition, and for new customers or new applications, refer to the A4970. NOTE: For detailed information on purchasing options, contact your local Allegro field applications engineer or sales representative. Allegro MicroSystems, Inc. reserves the right to make, from time to time, revisions to the anticipated product life cycle plan for a product to accommodate changes in production capabilities, alternative product availabilities, or market demand. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringements of patents or other rights of third parties which may result from its use. 2916 Dual Full-Bridge PWM Motor Driver Features and Benefits Description ▪ 750 mA continuous output current ▪ 45 V output sustaining voltage ▪ Internal clamp diodes ▪ Internal PWM current control ▪ Low output saturation voltage ▪ Internal thermal shutdown circuitry ▪ Similar to dual PBL3717 or UC3770 The UDx2916 motor drivers drive both windings of a bipolar stepper motor or bidirectionally control two DC motors. Both bridges are capable of sustaining 45 V and include internal pulse-width modulation (PWM) control of the output current to 750 mA. The outputs have been optimized for a low output saturation voltage drop (less than 1.8 V total source plus sink at 500 mA). For PWM current control, the maximum output current is determined by user selection of a reference voltage and sensing resistor. Two logic-level inputs select output current limits of 0%, 33%, 67%, or 100% of the maximum level. A PHASE input to each bridge determines load current direction. Packages Package B 24-pin Batwing DIP The bridges include both ground-clamp and flyback diodes for protection against inductive transients. Internally generated delays prevent crossover currents when switching current direction. Special power-up sequencing is not required. Thermal protection circuitry disables the outputs if the chip temperature exceeds safe operating limits. Package LB 24-pin Batwing SOICW The device is supplied in a 24-pin dual in-line plastic (DIP, package B) with two pairs of batwing leads as heat-sinkable tabs for enhanced power dissipation capabilities. The LB package is a 24-lead surface-mount wide SOIC with two pairs Package EB 44-pin PLCC with internally-fused leads Continued on the next page… Not to scale PWM Current-Control Circuitry VBB 'B' PACKAGE, CHANNEL 1 PIN NUMBERS SHOWN. 24 OUT B 1 21 OUT A V REF 15 23 20 k7 w10 40 k7 I 0 20 I 1 17 E SENSE – 22 ONE SHOT + RC 10 k7 RS 14 C C R T SOURCE DISABLE RC C T Dwg. EP-007B 29319.20R 2916 Dual Full-Bridge Motor Driver Description (continued) of batwing leads. The EB package is a 44-lead power PLCC with 11 internally-fused leads on two sides. Their webbed-lead construction provides for maximum package power dissipation in the smallest possible construction. The devices are available for operation from –20°C to 85°C (range N), and from –40°C to 105°C (range Q). All packages are lead (Pb) free, with 100% matte tin leadframe plating. Selection Guide Part Number Package Ambient Temperature (°C) Packing UDN2916B-T1 24-pin batwing DIP UDN2916EBTR-T1 44-pin internally fused lead PLCC 450 per reel UDN2916LBTR-T2 24-pin batwing SOICW 1000 per reel UDQ2916LBTR-T2 24-pin batwing SOICW 1000 per reel 15 per tube –20 to 85 –40 to 105 1This variant is in production, however, it has been deemed Pre-End of Life. The product is approaching end of life. Within a minimum of 6 months, the device will enter its final, Last Time Buy, order phase. Status change: November 1, 2010. 2This variant is in production, however, it has been deemed Pre-End of Life. The product is approaching end of life. Within a minimum of 6 months, the device will enter its final, Last Time Buy, order phase. Status change: January 31, 2011. Absolute Maximum Ratings Characteristic Symbol Rating Units 45 V VCC 7.0 V VIN –0.3 to VCC + 0.3 V VE 1.5 V 1.0 A 750 mA Motor Supply Voltage VBB Logic Supply Voltage Input Voltage Output Emitter Voltage Notes Peak Output Current* IOUT Continuous Package Power Dissipation PD See graph Output current rating may be limited by duty cycle, ambient temperature, and heat sinking. Under any set of conditions, do not exceed the specified current rating or TJ(max) — W Range N –20 to 85 ºC Range Q –40 to 105 ºC Operating Ambient Temperature TA Maximum Junction Temperature TJ(max) 150 ºC Tstg –55 to 150 ºC Storage Temperature Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 8535000 www.allegromicro.com 2 2916 Dual Full-Bridge Motor Driver 39 7 PWM 1 37 VBB 1 10 36 11 35 12 34 13 33 2 14 32 31 15 16 17 29 SUFFIX 'B', R 2 SUFFIX 'LB', R θJA = 55°C/W* 1 26 27 28 V REF 2 RC 2 25 50 75 100 TEMPERATURE IN °C 1 B Package (DIP) 24 LOAD SUPPLY 23 OUT 2B 22 SENSE 2 OUT 1A 1 OUT 2A 2 2 PHASE 2 3 V REF 2 4 21 E2 RC 2 5 20 OUT 2A GROUND 6 19 GROUND GROUND 7 18 GROUND LOGIC SUPPLY 8 17 OUT 1A I RC 1 99 16 E1 I 12 99 V REF 1 10 15 SENSE 1 P HAS E 2 10 PHASE 1 11 14 OUT 1B V REF 2 11 I 11 12 13 I 01 RC 2 12 VBB 2 V CC E2 PWM 1 1 Q1 150 *Measured on a single-layer board, with 1 sq. in. of 2 oz copper area. For additional information, refer to the Allegro Web site. I 12 Q2 125 Dwg. GP-035B Dwg. PP-006A PWM 2 02 = 40°C/W 3 LB Package (SOIC) I θJA 0 PHASE 2 I12 25 I02 24 OUT 2B 23 21 SENSE 2 SUFFIX 'EB', RθJA = 30°C/W GND Q2 NC E2 20 OUT 2A 18 NO CONNECTION 19 NC NO CONNECTION 22 GND 30 PWM 2 4 VBB 1 3 2 24 LOAD S UP P LY 23 E1 22 S E NS E 1 21 OUT 1B S E NS E 2 4 OUT 2B 5 20 I 01 G R OUND 6 19 G R OUND G R OUND 7 18 G R OUND 8 17 I 11 16 P HAS E 1 15 V REF 1 14 RC 1 13 LOG IC S UP P LY 02 θ2 P WM 1 9 38 R θJT = 6.0°C/W P WM 2 8 GND ALLOWABLE PACKAGE POWER DISSIPATION IN WATTS RC1 41 LOGIC SUPPLY VREF 1 42 VCC Q1 GND 5 40 I11 I01 1 PHASE 1 LOAD SUPPLY 2 43 OUT 1B 3 Power Dissipation 44 SENSE 1 4 1 OUT 1A E 6 5 EB Package (PLCC) θ1 V CC Dwg. P P -005 Dwg. PP-047 Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 8535000 www.allegromicro.com 3 2916 Dual Full-Bridge Motor Driver ELECTRICAL CHARACTERISTICS at TA = +25°C, TJ ≤ 150°C, VBB = 45 V, VCC = 4.75 V to 5.25 V, VREF = 5.0 V (unless otherwise noted). Limits Characteristic Symbol Test Conditions Min. Typ. Max. Units 10 — 45 V VOUT = VBB — < 1.0 50 μA VOUT = 0 —