AM79C961A

Am79C961A PCnet™-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA DISTINCTIVE CHARACTERISTICS s Single-chip Ethernet controller for the Industry Standard Architecture (ISA) and Extended Industry Standard Architecture (EISA) buses s Supports IEEE 802.3/ANSI 8802-3 and Ethernet standards s Supports full duplex operation on the 10BASE-T, AUI, and GPSI ports s Direct interface to the ISA or EISA bus s Pin compatible to Am79C961 PCnet-ISA+ Jumperless Single-Chip Ethernet Controller s Software compatible with AMD’s Am7990 LANCE register and descriptor architecture s Low power, CMOS design with sleep mode allows reduced power consumption for critical battery powered applications s Individual 136-byte transmit and 128-byte receive FIFOs provide packet buffering for increased system latency, and support the following features: — Automatic retransmission with no FIFO reload — Automatic receive stripping and transmit padding (individually programmable) — Automatic runt packet rejection — Automatic deletion of received collision frames s Dynamic transmit FCS generation programmable on a frame-by-frame basis s Single +5 V power supply s Internal/external loopback capabilities s Supports 8K, 16K, 32K, and 64K Boot PROMs or Flash for diskless node applications s Supports Microsoft’s Plug and Play System configuration for jumperless designs s Supports staggered AT bus drive for reduced noise and ground bounce s Integrated Magic Packet™ support for remote wake up of Green PCs s Supports 8 interrupts on chip s Look Ahead Packet Processing (LAPP) allows protocol analysis to begin before end of receive frame s Supports 4 DMA channels on chip s Supports 16 I/O locations s Supports 16 boot PROM locations s Provides integrated Attachment Unit Interface (AUI) and 10BASE-T transceiver with 2 modes of port selection: — Automatic selection of AUI or 10BASE-T — Software selection of AUI or 10BASE-T s Automatic Twisted Pair receive polarity detection and automatic correction of the receive polarity s Supports bus-master, programmed I/O, and shared-memory architectures to fit in any PC application s Supports edge and level-sensitive interrupts s DMA Buffer Management Unit for reduced CPU intervention which allows higher throughput by by-passing the platform DMA s JTAG Boundary Scan (IEEE 1149.1) test access port interface for board level production test s Integrated Manchester Encoder/Decoder s Supports the following types of network interfaces: — AUI to external 10BASE2, 10BASE5, 10BASE-T or 10BASE-F MAU — Internal 10BASE-T transceiver with Smart Squelch to Twisted Pair medium s Supports LANCE General Purpose Serial Interface (GPSI) s 132-pin PQFP and 144-pin TQFP packages s Supports Shared Memory and PIO modes s Supports PCMCIA mode (144-TQFP version only) s Support for operation in industrial temperature range (–40°C to +85°C) available in both packages Publication# 19364 Rev: D Amendment/0 Issue Date: March 2000 GENERAL DESCRIPTION The PCnet-ISA II controller, a single-chip Ethernet controller, is a highly integrated system solution for the PC-AT Industry Standard Architecture (ISA) architecture. It is designed to provide flexibility and compatibility with any existing PC application. This highly integrated VLSI device is specifically designed to reduce parts count and cost, and addresses applications where higher system throughput is desired. The PCnet-ISA II controller is fabricated with AMD’s advanced low-power CMOS process to provide low standby current for power sensitive applications. The PCnet-ISA II controller can be configured into one of three different architecture modes to suit a particular PC application. In the Bus Master mode, all transfers are performed using the integrated DMA controller. This configuration enhances system performance by allowing the PCnet-ISA II controller to bypass the platform DMA controller and directly address the full 24-bit memory space. The implementation of Bus Master mode allows minimum parts count for the majority of PC applications. The PCnet-ISA II can also be configured as a Bus Slave with either a Shared Memory or Programmed I/O architecture for compatibility with low-end machines, such as PC/XTs that do not support Bus Masters, and high-end machines that require local packet buffering for increased system latency. The PCnet-ISA II controller is designed to directly interface with the ISA or EISA system bus. It contains an ISA Plug and Play bus interface unit, DMA Buffer Management Unit, 802.3 Media Access Control function, individual 136-byte transmit and 128-byte receive FIFOs, IEEE 802.3 defined Attachment Unit Interface (AUI), and a Twisted Pair Transceiver Media Attachment Unit. Full duplex network operation can be enabled on any of the device’s network ports. The PCnet-ISA II controller is also register compatible with the LANCE (Am7990) Ethernet controller and PCnet-ISA (Am79C960). The DMA Buffer Management Unit supports the LANCE descriptor software model. External remote boot and Ethernet physical address PROMs and Electrically Erasable Proms are also supported. This advanced Ethernet controller has the built-in capability of automatically selecting either the AUI port or the Twisted Pair transceiver. Only one interface is active at any one time. The individual 136-byte transmit and 128-byte receive FIFOs optimize system overhead, providing sufficient latency during packet transmission and reception, and minimizing intervention during normal network error recovery. The integrated Manchester encoder/decoder eliminates the need for an external Serial Interface Adapter (SIA) in the node system. If support for an external encoding/decoding scheme is desired, the embedded General Purpose Serial Interface (GPSI) allows direct access to/from the MAC. In addition, the device provides programmable on-chip LED drivers for transmit, receive, collision, receive polarity, link integrity and activity, or jabber status. The PCnet-ISA II controller also provides an External Address Detection InterfaceTM (EADITM) to allow external hardware address filtering in internetworking applications. For power sensitive applications where low stand-by current is desired, the device incorporates a sleep function to reduce over-all system power consumption, excellent for notebooks and Green PCs. In conjunction with this low power mode, the PCnet-ISA II controller also has integrated functions to support Magic Packet, an inexpensive technology that allows remote wake up of Green PCs. With the rise of embedded networking applications operating in harsh environments where temperatures may exceed the normal commercial temperature (0°C to +70°C) window, an industrial temperature (–40°C to +85°C) version is available in all two packages; 132-pin PQFP and 144-pin TQFP. The industrial temperature version of the PCnet-ISA II Ethernet controller is characterized across the industrial temperature range (–40°C to +85°C) within the published power supply specification (4.75 V to 5.25 V; i.e., ±5% VCC). 2 Am79C961A BLOCK DIAGRAM: BUS MASTER MODE AEN DACK[3, 5–7] DRQ[3, 5–7] IOCHRDY IOCS16 IOR IOW IRQ[3, 4, 5, 9, 10, 11, 12] MASTER MEMR MEMW REF RESET SBHE BALE FIFO Control Private Bus Control RXD+/– 10BASE-T MAU TXD+/– TXPD+/– ISA Bus Interface Unit RCV FIFO 802.3 MAC Core DXCVR/EAR CI+/– Encoder/ Decoder (PLS) & AUI Port XMT FIFO DI+/– XTAL1 XTAL2 DO+/– SD[0-15] IRQ15/APCS BPCS LED[0–3] PRDB[0–7] LA[17-23] SA[0-19] SLEEP SHFBUSY EEDO EEDI EESK EECS Buffer Management Unit TDO EEPROM Interface Unit JTAG Port Control TMS TDI TCK DVDD[1-7] DVSS[1-13] AVDD[1-4] AVSS[1-2] 19364B-1 Am79C961A 3 TABLE OF CONTENTS Am79C961A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 DISTINCTIVE CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 BLOCK DIAGRAM: BUS MASTER MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Standard Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 CONNECTION DIAGRAMS: BUS MASTER MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 PQFP 132 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 PIN DESIGNATIONS: BUS MASTER MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Listed by Pin Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 PIN DESIGNATIONS: BUS MASTER MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Listed by Pin Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 PIN DESIGNATIONS: BUS MASTER MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Listed by Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Listed by Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 PIN DESCRIPTION: BUS MASTER MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 IEEE P996 Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 ISA Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 AEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 BALE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 DACK 3, 5-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 DRQ 3, 5-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 IOCHRDY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 IOCS16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 IOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 IOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 IRQ 3, 4, 5, 9, 10, 11, 12, 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 LA17-23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 MASTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 MEMR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 MEMW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 REF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 SA0-19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 SBHE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 SD0-15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Board Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 IRQ12/FlashWE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 IRQ15/APCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 BPCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 DXCVR/EAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 LEDO-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 PRDB3-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 PRDB2/EEDO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 PRDB1/EEDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 PRDB0/EESK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 SHFBUSY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 EECS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 SLEEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 XTAL1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 XTAL2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 CONNECTION DIAGRAMS: BUS SLAVE MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 PQFP 132 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 BLOCK DIAGRAM: BUS SLAVE MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 PIN DESIGNATIONS: BUS SLAVE MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 4 Am79C961A LISTED BY PIN NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 PIN DESIGNATIONS: BUS SLAVE MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Listed by Pin Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 PIN DESIGNATIONS: BUS SLAVE MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Listed by Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 PIN DESIGNATIONS: BUS SLAVE MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Listed by Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 PIN DESCRIPTION: BUS SLAVE MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 ISA Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 AEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 IOCHRDY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 IOCS16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 IOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 IOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 IRQ3, 4, 5, 9, 10, 11, 12, 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 MEMR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 MEMW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 REF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 SA0-15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 SBHE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 SD0-15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Board Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 APCS/IRQ15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 BPAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 BPCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 DXCVR/EAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 LED0-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 PRAB0-15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 PRDB3-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 PRDB2/EEDO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 PRDB1/EEDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 PRDB0/EESK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 SHFBUSY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 EECS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 SLEEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 SMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 SMAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 SROE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 SRCS/IRQ12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 SRWE/WE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 XTAL1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 XTAL2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 PIN DESCRIPTION: NETWORK INTERFACES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 AUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 DI+, DI– . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Twisted Pair Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 RXD+, RXD– . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 TXD+, TXD– . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 TXP+, TXP– . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 PIN DESCRIPTION: IEEE 1149.1 (JTAG) TEST ACCESS PORT . . . . . . . . . . . . . . . . . . . . . . . . . . .31 TCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 TDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 TDO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 TMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 PIN DESCRIPTION: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 POWER SUPPLIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 AVDD1–4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Am79C961A 5 AVSS1–2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 DVDD1–7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 DVSS1–13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 CONNECTION DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 TQFP 144 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 PIN DESIGNATIONS: BUS MASTER MODE (TQFP 144) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Listed by Pin Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 PIN DESIGNATIONS: BUS MASTER MODE (TQFP 144) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Listed by Pin Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 PIN DESIGNATIONS: BUS SLAVE (PIO AND SHARED MEMORY) MODES (TQFP 144) . . . . . . .35 Listed by Pin Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 PIN DESIGNATIONS: BUS SLAVE (PIO AND SHARED MEMORY) MODES (TQFP 144) . . . . . . .36 Listed by Pin Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 BLOCK DIAGRAM: PCMCIA MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 PIN DESIGNATIONS: PCMCIA MODE (TQFP 144) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Listed by Pin Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 PIN DESIGNATIONS: PCMCIA MODE (TQFP 144) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Listed by Pin Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 PIN DESCRIPTION: PCMCIA MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 PCMCIA vs. ISA Pinout Comparison . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 PCMCIA Pin Specification Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 PCMCIA MODE BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 PCMCIA Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Serial EEPROM Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Flash Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Flash Memory Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Shared Memory vs. Programmed I/O Implications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 FLASH MEMORY MAP AND CARD REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Important Note About The EEPROM Byte Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Bus Master Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Bus Slave Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 PLUG AND PLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 Auto-Configuration Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 ADDRESS PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 WRITE_DATA PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 READ_DATA PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 Initiation Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 Isolation Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Hardware Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Software Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 Plug and Play Card Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 Plug and Play Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 PLUG AND PLAY LOGICAL DEVICE CONFIGURATION REGISTERS . . . . . . . . . . . . . . . . . . . . .54 DETAILED FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 Important Note About The EEPROM Byte Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 Basic EEPROM Byte Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 AMD Device Driver Compatible EEPROM Byte Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 Plug and Play Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 PCnet–ISA II’s Legacy Bit Feature Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 Plug & Play Register Locations Detailed Description (Refer to the Plug & Play Register Map above) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 6 Am79C961A Vendor Defined Byte (PnP 0xF0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 Checksum Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 Use Without EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 External Scan Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 Flash PROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 Optional IEEE Address PROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 EISA Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 Bus Interface Unit (BIU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 DMA Transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 1. Initialization Block DMA Transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 2. Descriptor DMA Transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 3. FIFO DMA Transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 Buffer Management Unit (BMU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Reinitialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Suspend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Buffer Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Descriptor Rings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Descriptor Ring Access Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 Polling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Transmit Descriptor Table Entry (TDTE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 Receive Descriptor Table Entry (RDTE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 Media Access Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 Transmit and Receive Message Data Encapsulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 Media Access Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 Manchester Encoder/Decoder (MENDEC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 External Crystal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 External Clock Drive Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 MENDEC Transmit Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 Transmitter Timing and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 Receive Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 Input Signal Conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 Clock Acquisition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 PLL Tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 Carrier Tracking and End of Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 Data Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 Differential Input Terminations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 Collision Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 Jitter Tolerance Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 Attachment Unit Interface (AUI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 Twisted Pair Transceiver (T-MAU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 Twisted Pair Transmit Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 Twisted Pair Receive Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 Link Test Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 Polarity Detection and Reversal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78 Twisted Pair Interface Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78 Collision Detect Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78 Signal Quality Error (SQE) Test (Heartbeat) Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Jabber Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Power Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Full Duplex Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 EADI (External Address Detection Interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 General Purpose Serial Interface (GPSI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 Boundary Scan Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 TAP FSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 Supported Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 Am79C961A 7 Instruction Register and Decoding Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 Boundary Scan Register (BSR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 Other Data Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 Power Saving Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 Access Operations (Software) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 I/O Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 I/O Register Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 IEEE Address Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 Boot PROM Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 Static RAM Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 Bus Cycles (Hardware) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 Bus Master Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 Address PROM Cycles External PROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 Address PROM Cycles Using EEPROM Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 Ethernet Controller Register Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 Transmit Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 Transmit Function Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 Automatic Pad Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 Transmit FCS Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 Transmit Exception Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 Receive Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92 Receive Function Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92 Automatic Pad Stripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92 Receive FCS Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93 Receive Exception Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93 Loopback Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94 MAGIC PACKET OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 Magic Packet Mode Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 Magic Packet Receive Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 PCNET-ISA II CONTROLLER REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96 Register Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96 RAP: Register Address Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96 Control and Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96 CSR0: PCnet-ISA II Controller Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96 CSR1: IADR[15:0] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 CSR2: IADR[23:16] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 CSR3: Interrupt Masks and Deferral Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 CSR4: Test and Features Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100 CSR5: Control 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101 CSR6: RCV/XMT Descriptor Table Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 CSR8: Logical Address Filter, LADRF[15:0] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 CSR9: Logical Address Filter, LADRF[31:16] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 CSR10: Logical Address Filter, LADRF[47:32] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 CSR11: Logical Address Filter, LADRF[63:48] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 CSR12: Physical Address Register, PADR[15:0] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 CSR13: Physical Address Register, PADR[31:16] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 CSR14: Physical Address Register, PADR[47:32] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 CSR15: Mode Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 CSR16: Initialization Block Address Lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105 CSR17: Initialization Block Address Upper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105 CSR18-19: Current Receive Buffer Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105 CSR20-21: Current Transmit Buffer Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105 CSR22-23: Next Receive Buffer Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 CSR24-25: Base Address of Receive Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 CSR26-27: Next Receive Descriptor Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 CSR28-29: Current Receive Descriptor Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 CSR30-31: Base Address of Transmit Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 8 Am79C961A CSR32-33: Next Transmit Descriptor Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 CSR34-35: Current Transmit Descriptor Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 CSR36-37: Next Next Receive Descriptor Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 CSR38-39: Next Next Transmit Descriptor Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 CSR40-41: Current Receive Status and Byte Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 CSR42-43: Current Transmit Status and Byte Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 CSR44-45: Next Receive Status and Byte Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 CSR46: Poll Time Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 CSR47: Polling Interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 CSR48-49: Temporary Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 CSR50-51: Temporary Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 CSR52-53: Temporary Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 CSR54-55: Temporary Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 CSR56-57: Temporary Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 CSR58-59: Temporary Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 CSR60-61: Previous Transmit Descriptor Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 CSR62-63: Previous Transmit Status and Byte Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 CSR64-65: Next Transmit Buffer Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 CSR66-67: Next Transmit Status and Byte Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 CSR70-71: Temporary Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 CSR72: Receive Ring Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 CSR74: Transmit Ring Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 CSR76: Receive Ring Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 CSR78: Transmit Ring Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 CSR80: Burst and FIFO Threshold Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 CSR82: Bus Activity Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 CSR84-85: DMA Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 CSR86: Buffer Byte Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 CSR88-89: Chip ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 CSR92: Ring Length Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 CSR94: Transmit Time Domain Reflectometry Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 CSR96-97: Bus Interface Scratch Register 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 CSR98-99: Bus Interface Scratch Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 CSR104-105: SWAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 CSR108-109: Buffer Management Scratch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 CSR112: Missed Frame Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 CSR114: Receive Collision Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 CSR124: Buffer Management Unit Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 ISACSR0: Master Mode Read Active/SRAM Data Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114 ISACSR1: Master Mode Write Active/SRAM Address Pointer . . . . . . . . . . . . . . . . . . . . . . . .114 ISACSR2: Miscellaneous Configuration 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115 ISACSR3: EEPROM Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116 ISACSR4: LED0 Status (Link Integrity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117 ISACSR5: LED1 Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117 ISACSR6: LED2 Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118 ISACSR7: LED3 Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119 ISACSR8: Software Configuration Register (Read-Only Register) . . . . . . . . . . . . . . . . . . . . .120 ISACSR9: Miscellaneous Configuration 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120 Initialization Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120 RLEN and TLEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120 RDRA and TDRA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121 LADRF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121 PADR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121 MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121 Receive Descriptors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 RMD0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 RMD1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 RMD2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 Am79C961A 9 RMD3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123 Transmit Descriptors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123 TMD0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123 TMD1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123 TMD2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124 TMD3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124 Register Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126 Ethernet Controller Registers (Accessed via RDP Port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126 Register Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127 REGISTER SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 ISACSR—ISA Bus Configuration Registers (Accessed via IDP Port) . . . . . . . . . . . . . . . . . .128 SYSTEM APPLICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 ISA Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 Compatibility Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 Bus Master . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 Shared Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 Optional Address PROM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132 Boot PROM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132 Static RAM Interface (for Shared Memory Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133 AUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133 EEPROM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133 10BASE-T Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133 ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 OPERATING RANGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 Commercial (C) Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 Industrial (I) Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 DC CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 SWITCHING CHARACTERISTICS: BUS MASTER MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137 SWITCHING CHARACTERISTICS: BUS MASTER MODE—FLASH READ CYCLE . . . . . . . . . . 140 SWITCHING CHARACTERISTICS: BUS MASTER MODE—FLASH WRITE CYCLE . . . . . . . . . .140 SWITCHING CHARACTERISTICS: SHARED MEMORY MODE . . . . . . . . . . . . . . . . . . . . . . . . . 141 SWITCHING CHARACTERISTICS: SHARED MEMORY MODE—FLASH READ CYCLE . . . . . .144 SWITCHING CHARACTERISTICS: SHARED MEMORY MODE—FLASH WRITE CYCLE . . . . . .144 SWITCHING CHARACTERISTICS: EADI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 SWITCHING CHARACTERISTICS: JTAG (IEEE 1149.1) INTERFACE . . . . . . . . . . . . . . . . . . . . .145 SWITCHING CHARACTERISTICS: GPSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146 SWITCHING CHARACTERISTICS: AUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147 SWITCHING CHARACTERISTICS: 10BASE-T INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . .148 SWITCHING CHARACTERISTICS: SERIAL EEPROM INTERFACE . . . . . . . . . . . . . . . . . . . . . . 148 SWITCHING TEST CIRCUITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 SWITCHING WAVEFORMS: BUS MASTER MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152 SWITCHING WAVEFORMS: SHARED MEMORY MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .162 SWITCHING WAVEFORMS: GPSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172 SWITCHING WAVEFORMS: EADI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 SWITCHING WAVEFORMS: JTAG (IEEE 1149.1) INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 SWITCHING WAVEFORMS: AUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .174 SWITCHING WAVEFORMS: 10BASE-T INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .178 PHYSICAL DIMENSIONS* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180 PQB132 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180 PHYSICAL DIMENSIONS* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181 PQB132 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181 PCnet-ISA II Compatible Media Interface Modules . . . . . . . . . . . . . . . . . . . . . . . . . .183 PCNET-ISA II COMPATIBLE 10BASE-T FILTERS AND TRANSFORMERS . . . . . . . . . . . . . . . . . 183 PCNET-ISA II COMPATIBLE AUI ISOLATION TRANSFORMERS . . . . . . . . . . . . . . . . . . . . . . . . . 183 PCNET-ISA II COMPATIBLE DC/DC CONVERTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 MANUFACTURER CONTACT INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 10 Am79C961A Layout Recommendations for Reducing Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . .185 DECOUPLING LOW-PASS R/C FILTER DESIGN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 Digital Decoupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .185 Analog Decoupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .185 AVSS1 and AVDD3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .185 AVSS2 and AVDD2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .185 AVSS2 and AVDD2/AVDD4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .186 Sample Plug and Play Configuration Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187 SAMPLE CONFIGURATION FILE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 Alternative Method for Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .189 Introduction of the Look-Ahead Packet Processing (LAPP) Concept . . . . . . . . . .191 Outline of the LAPP Flow: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .191 SETUP: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192 FLOW: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192 LAPP Enable Software Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .194 LAPP Enable Rules for Parsing of Descriptors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .194 Some Examples of LAPP Descriptor Interaction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .195 Buffer Size Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .196 Some Characteristics of the XXC56 Serial EEPROMs . . . . . . . . . . . . . . . . . . . . . . .201 SWITCHING CHARACTERISTICS OF A TYPICAL XXC56 SERIAL EEPROM INTERFACE . . . .201 INSTRUCTION SET FOR THE XXC56 SERIES OF EEPROMS . . . . . . . . . . . . . . . . . . . . . . . . . . . 202 Am79C961A PCnet-ISA II Silicon Errata Report . . . . . . . . . . . . . . . . . . . . . . . . . . . .203 AM79C961A REV FD SILICON STATUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 Am79C961A 11 ORDERING INFORMATION Standard Products AMD standard products are available in several packages and operating ranges. The order number (Valid Combination) is formed by a combination of: AM79C961A K C \W ALTERNATE PACKAGING OPTION \W=Trimmed and Formed (PQB132) OPTIONAL PROCESSING Blank=Standard Processing TEMPERATURE RANGE C=Commercial (0°C to +70°C) I =Industrial (–40°C to +85°C) PACKAGE TYPE (per Prod. Nomenclature/16-038) K=132-pin Plastic Quad Flat Pack (PQR132) V=144-pin Thin Quad Flat Package (PQT144) SPEED Not Applicable DEVICE NUMBER/DESCRIPTION Am79C961A PCnet-ISA II Jumperless Single-Chip Ethernet Controller for ISA Valid Combinations KC, KC\W AM79C961A VC, VC\W KI, KI\W AM79C961A VI, VI\W Valid Combinations Valid Combinations list configurations planned to be supported in volume for this device. Consult the local AMD sales office to confirm availability of specific valid combinations and to check on newly released combinations. 12 Am79C961A CONNECTION DIAGRAMS: BUS MASTER MODE DVSS3 MASTER DRQ7 DRQ6 DRQ5 DVSS10 DACK7 DACK6 DACK5 LA17 LA18 LA19 LA20 DVSS4 LA21 LA22 LA23 SBHE DVDD3 SA0 SA1 SA2 DVSS5 SA3 SA4 SA5 SA6 SA7 SA8 SA9 DVSS6 SA10 SA11 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 PQFP 132 Am79C961A Am79C961AKC DVDD4 SA12 SA13 SA14 SA15 DVSS7 SA16 SA17 SA18 SA19 AEN IOCHRDY MEMW MEMR DVSS11 IRQ15/APCS IRQ12/FLASHWE IRQ11 DVDD5 IRQ10 IOCS16 BALE IRQ3 IRQ4 IRQ5 REF DVSS12 DRQ3 DACK3 IOR IOW IRQ9 RESET 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 XTAL2 AVSS2 XTAL1 AVDD3 TXD+ TXPD+ TXD– TXPD– AVDD4 RXD+ RXD– DVSS13 SD15 SD7 SD14 SD6 DVSS9 SD13 SD5 SD12 SD4 DVDD7 SD11 SD3 SD10 SD2 DVSS8 SD9 SD1 SD8 SD0 SLEEP DVDD6 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 DVDD2 TCK TMS TDO TDI EECS BPCS SHFBUSY PRDB0/EESK PRDB1/EEDI PRDB2/EEDO PRDB3 DVSS2 PRDB4 PRDB5 PRDB6 PRDB7 DVDD1 LED0 LED1 DVSS1 LED2 LED3 DXCVR/EAR AVDD2 CI+ CI– DI+ DI– AVDD1 DO+ DO– AVSS1 19364B-2 13 PIN DESIGNATIONS: BUS MASTER MODE Listed by Pin Number Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Pin Name DVSS3 MASTER DRQ7 DRQ6 DRQ5 DVSS10 DACK7 DACK6 DACK5 LA17 LA18 LA19 LA20 DVSS4 LA21 LA22 LA23 SBHE DVDD3 SA0 SA1 SA2 DVSS5 SA3 SA4 SA5 SA6 SA7 SA8 SA9 DVSS6 SA10 SA11 Pin No. 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 Pin Name DVDD4 SA12 SA13 SA14 SA15 DVSS7 SA16 SA17 SA18 SA19 AEN IOCHRDY MEMW MEMR DVSS11 IRQ15/APCS IRQ12/FlashWE IRQ11 DVDD5 IRQ10 IOCS16 BALE IRQ3 IRQ4 IRQ5 REF DVSS12 DRQ3 DACK3 IOR IOW IRQ9 RESET Pin No. 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 Pin Name DVDD6 SLEEP SD0 SD8 SD1 SD9 DVSS8 SD2 SD10 SD3 SD11 DVDD7 SD4 SD12 SD5 SD13 DVSS9 SD6 SD14 SD7 SD15 DVSS13 RXD– RXD+ AVDD4 TXPD– TXD– TXPD+ TXD+ AVDD3 XTAL1 AVSS2 XTAL2 Pin No. 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 Pin Name AVSS1 DO– DO+ AVDD1 DI– DI+ CI– CI+ AVDD2 DXCVR/EAR LED3 LED2 DVSS1 LED1 LED0 DVDD1 PRDB7 PRDB6 PRDB5 PRDB4 DVSS2 PRDB3 PRDB2/EEDO PRDB1/EEDI PRDB0/EESK SHFBUSY BPCS EECS TDI TDO TMS TCK DVDD2 14 Am79C961A PIN DESIGNATIONS: BUS MASTER MODE Listed by Pin Name Pin Name AEN AVDD1 AVDD2 AVDD3 AVDD4 AVSS1 AVSS2 BALE BPCS CI– CI+ DACK3 DACK5 DACK6 DACK7 DI– DI+ DO– DO+ DRQ3 DRQ5 DRQ6 DRQ7 DVDD1 DVDD2 DVDD3 DVDD4 DVDD5 DVDD6 DVDD7 DVSS1 DVSS10 DVSS11 Pin No. 44 103 108 96 91 100 98 55 126 106 107 62 9 8 7 104 105 101 102 61 5 4 3 115 132 19 34 52 67 78 112 6 48 Pin Name DVSS12 DVSS13 DVSS2 DVSS3 DVSS4 DVSS5 DVSS6 DVSS7 DVSS8 DVSS9 DXCVR/EAR EECS IOCHRDY IOCS16 IOR IOW IRQ10 IRQ11 IRQ12/FlashWE IRQ15/APCS IRQ3 IRQ4 IRQ5 IRQ9 LA17 LA18 LA19 LA20 LA21 LA22 LA23 LED0 LED1 Pin No. 60 88 120 1 14 23 31 39 73 83 109 127 45 54 63 64 53 51 50 49 56 57 58 65 10 11 12 13 15 16 17 114 113 Pin Name LED2 LED3 MASTER MEMR MEMW PRDB0/EESK PRDB1/EEDI PRDB2/EEDO PRDB3 PRDB4 PRDB5 PRDB6 PRDB7 REF RESET RXD– RXD+ SA0 SA1 SA10 SA11 SA12 SA13 SA14 SA15 SA16 SA17 SA18 SA19 SA2 SA3 SA4 SA5 Pin No. 111 110 2 47 46 124 123 122 121 119 118 117 116 59 66 89 90 20 21 32 33 35 36 37 38 40 41 42 43 22 24 25 26 Pin Name SA6 SA7 SA8 SA9 SBHE SD0 SD1 SD10 SD11 SD12 SD13 SD14 SD15 SD2 SD3 SD4 SD5 SD6 SD7 SD8 SD9 SHFBUSY SLEEP TCK TDI TDO TMS TXD– TXD+ TXPD– TXPD+ XTAL1 XTAL2 Pin No. 27 28 29 30 18 69 71 75 77 80 82 85 87 74 76 79 81 84 86 70 72 125 68 131 128 129 130 93 95 92 94 97 99 Am79C961A 15 PIN DESIGNATIONS: BUS MASTER MODE Listed by Group Pin Name ISA Bus Interface AEN BALE DACK[3, 5–7] DRQ[3, 5–7] IOCHRDY IOCS16 IOR IOW IRQ[3, 4, 5, 9, 10, 11, 12, 15] LA[17-23] MASTER MEMR MEMW REF RESET SA[0 –19] SBHE SD[0 –15] Board Interfaces IRQ15/APCS BPCS DXCVR/EAR LED0 LED1 LED2 LED3 PRDB[3–7] SLEEP XTAL1 XTAL2 SHFBUSY PRDB(0)/EESK PRDB(1)/EEDI PRDB(2)/EEDO EECS IRQ15 or Address PROM Chip Select Boot PROM Chip Select Disable Transceiver LED0/LNKST LED1/SFBD/RCVACT LED2/SRD/RXDATPOL LED3/SRDCLK/XMTACT PROM Data Bus Sleep Mode Crystal Input Crystal Output Read access from EEPROM in process Serial Shift Clock Serial Shift Data In Serial Shift Data Out EEPROM Chip Select O O I/O O O O O I/O I I O I/O I/O I/O O TS1 TS1 TS1 TS2 TS2 TS2 TS2 TS1 Address Enable Bus Address Latch Enable DMA Acknowledge DMA Request I/O Channel Ready I/O Chip Select 16 I/O Read Select I/O Write Select Interrupt Request Unlatched Address Bus Master Transfer in Progress Memory Read Select Memory Write Select Memory Refresh Active System Reset System Address Bus System Byte High Enable System Data Bus I I I I/O I/O O I I O I/O O O O I I I/O I/O I/O TS3 TS3 TS3 TS3/OD3 TS3 OD3 TS3 TS3 TS3 OD3 OD3 Pin Function I/O Driver 16 Am79C961A PIN DESIGNATIONS: BUS MASTER MODE (continued) Listed by Group Pin Name Attachment Unit Interface (AUI) CI± DI± DO± Twisted Pair Transceiver Interface (10BASE-T) RXD± TXD± TXPD± 10BASE-T Receive Data 10BASE-T Transmit Data 10BASE-T Predistortion Control I O O Collision Inputs Receive Data Transmit Data I I O Pin Function I/O Driver IEEE 1149.1 Test Access Port Interface (JTAG) TCK TDI TDO TMS Power Supplies AVDD AVSS DVDD DVSS Analog Power [1-4] Analog Ground [1-2] Digital Power [1-7] Digital Ground [1-13] Test Clock Test Data Input Test Data Output Test Mode Select I I O I TS2 Output Driver Types Name TS1 TS2 TS3 OD3 Type Tri-State Tri-State Tri-State Open Drain IOL (mA) 4 12 24 24 IOH (mA) –1 –4 –3 –3 pF 50 50 120 120 Am79C961A 17 PIN DESCRIPTION: BUS MASTER MODE These pins are part of the bus master mode. In order to understand the pin descriptions, definition of some terms from a draft of IEEE P996 are included. between back-to-back DMA requests. See the Back-to-Back DMA Requests section for details. Because of the operation of the Plug and Play registers, the DMA Channels on the PCnet-ISA II must be attached to the specific DRQ and DACK signals on the PC/AT bus as indicated by the pin names. IEEE P996 Terminology Alternate Master : Any device that can take control of the bus through assertion of the MASTER signal. It has the ability to generate addresses and bus control signals in order to perform bus operations. All Alternate Masters must be 16 bit devices and drive SBHE. Bus Ownership: The Current Master possesses bus ownership and can assert any bus control, address and data lines. Current Master : The Permanent Master, Temporary Master or Alternate Master which currently has ownership of the bus. Permanent Master : Each P996 bus will have a device known as the Permanent Master that provides certain signals and bus control functions as described in Section 3.5 (of the IEEE P996 spec.), “Permanent Master”. The Permanent Master function can reside on a Bus Adapter or on the backplane itself. Temporary Master : A device that is capable of generating a DMA request to obtain control of the bus and directly asserting only the memory and I/O strobes during bus transfer. Addresses are generated by the DMA device on the Permanent Master. IOCHRDY I/O Channel Ready Input/Output When the PCnet-ISA II controller is being accessed, IOCHRDY HIGH indicates that valid data exists on the data bus for reads and that data has been latched for writes. When the PCnet-ISA II controller is the Current Master on the ISA bus, it extends the bus cycle as long as IOCHRDY is LOW. IOCS16 I/O Chip Select 16 Output When an I/O read or write operation is performed, the PCnet-ISA II controller will drive the IOCS16 pin LOW to indicate that the chip supports a 16-bit operation at this address. (If the motherboard does not receive this signal, then the motherboard will convert a 16-bit access to two 8-bit accesses). The PCnet-ISA II controller follows the IEEE P996 specification that recommends this function be implemented as a pure decode of SA0-9 and AEN, with no dependency on IOR, or IOW; however, some PC/AT clone systems are not compatible with this approach. For this reason, the PCnet-ISA II controller is recommended to be configured to run 8-bit I/O on all machines. Since data is moved by memory cycles there is virtually no performance loss incurred by running 8-bit I/O and compatibility problems are virtually eliminated. The PCnet-ISA II controller can be configured to run 8-bit-only I/O by clearing Bit 0 in Plug and Play register F0. ISA Interface AEN Address Enable Input This signal must be driven LOW when the bus performs an I/O access to the device. BALE Used to latch the LA20–23 address lines. IOR I/O Read Input IOR is driven LOW by the host to indicate that an Input/ Output Read operation is taking place. IOR is only valid if the AEN signal is LOW and the external address matches the PCnet-ISA II controller’s predefined I/O address location. If valid, IOR indicates that a slave read operation is to be performed. DACK 3, 5-7 DMA Acknowledge Input Asserted LOW when the Permanent Master acknowledges a DMA request. When DACK is asserted the PCnet-ISA II controller becomes the Current Master by asserting the MASTER signal. DRQ 3, 5-7 DMA Request Input/Output When the PCnet-ISA II controller needs to perform a DMA transfer, it asserts DRQ. The Permanent Master acknowledges DRQ with the assertion of DACK. When the PCnet-ISA II does not need the bus it desserts DRQ. The PCnet-ISA II provides for fair bus bandwidth sharing between two bus mastering devices on the ISA bus through an adaptive delay which is inserted IOW I/O Write Input IOW is driven LOW by the host to indicate that an Input/ Output Write operation is taking place. IOW is only valid if AEN signal is LOW and the external address matches the PCnet-ISA II controller’s predefined I/O address location. If valid, IOW indicates that a slave write operation is to be performed. 18 Am79C961A IRQ 3, 4, 5, 9, 10, 11, 12, 15 Interrupt Request Output An attention signal which indicates that one or more of the following status flags is set: BABL, MISS, MERR, RINT, IDON, RCVCCO, JAB, MPCO, or TXDATSTRT. All status flags have a mask bit which allows for suppression of IRQ asser tion. These flags have the following meaning: BABL RCVCCO JAB MISS MERR MPCO RINT IDON TXDATSTRT Babble Receive Collision Count Overflow Jabber Missed Frame Memory Error Missed Packet Count Overflow Receive Interrupt Initialization Done Transmit Start (DRQ), the Ethernet controller asserts the MASTER signal to indicate to the Permanent Master that the PCnet-ISA II controller is becoming the Current Master. MEMR Memory Read Input/Output MEMR goes LOW to perform a memory read operation. MEMW Memory Write Input/Output MEMW g oes LOW to perfor m a memor y wr ite operation. REF Memory Refresh Input When REF is asserted, a memory refresh is active. The PCnet-ISA II controller uses this signal to mask inadvertent DMA Acknowledge assertion during memory refresh periods. If DACK i s asserted when REF i s active, DACK assertion is ignored. REF is monitored to eliminate a bus arbitration problem observed on some ISA platforms. Because of the operation of the Plug and Play registers, the interrupts on the PCnet-ISA II must be attached to specific IRQ signals on the PC/AT bus. RESET Reset Input When RESET is asserted HIGH the PCnet-ISA II controller performs an internal system reset. RESET must be held for a minimum of 10 XTAL1 periods before being deasserted. While in a reset state, the PCnet-ISA II controller will tristate or deassert all outputs to predefined reset levels. The PCnet-ISA II controller resets itself upon power-up. LA17-23 Unlatched Address Bus Input/Output The unlatched address bus is driven by the PCnet-ISA II controller during bus master cycle. The functions of these unlatched address pins will change when GPSI mode is invoked. The following table shows the pin configuration in GPSI mode. Please refer to the section on General Purpose Serial Interface for detailed information on accessing this mode. Pin Number 10 11 12 13 15 16 17 Pin Function in Bus Master Mode LA17 LA18 LA19 LA20 LA21 LA22 LA23 Pin Function in GPSI Mode RXDAT SRDCLK RXCRS CLSN STDCLK TXEN TXDAT SA0-19 System Address Bus Input/Output This bus contains address information, which is stable during a bus operation, regardless of the source. SA17-19 contain the same values as the unlatched address LA17-19. When the PCnet-ISA II controller is the Current Master, SA0-19 will be driven actively. When the PCnet-ISA II controller is not the Current Master, the SA0-19 lines are continuously monitored to determine if an address match exists for I/O slave transfers or Boot PROM accesses. SBHE System Byte High Enable Input/Output This signal indicates the high byte of the system data bus is to be used. SBHE is driven by the PCnet-ISA II controller when performing bus mastering operations. MASTER Master Mode Input/Output This signal indicates that the PCnet-ISA II controller has become the Current Master of the ISA bus. After the PCnet-ISA II controller has received a DMA Acknowledge (DACK) in response to a DMA Request SD0-15 System Data Bus Input/Output These pins are used to transfer data to and from the PCnet-ISA II controller to system resources via the ISA data bus. SD0-15 is driven by the PCnet-ISA II control- Am79C961A 19 ler when performing bus master writes and slave read operations. Likewise, the data on SD0-15 is latched by the PCnet-ISA II controller when performing bus master reads and slave write operations. If EADI mode is selected, this pin becomes the EAR input. The incoming frame will be checked against the internally active address detection mechanisms and the result of this check will be OR’d with the value on the EAR pin. The EAR pin is defined as REJECT. (See the EADI section for details regarding the function and timing of this signal). Board Interface IRQ12/FlashWE Flash Write Enable Output Optional interface to the Flash memory boot PROM Write Enable. LEDO-3 LED Drivers Output These pins sink 12 mA each for driving LEDs. Their meaning is software configurable (see section The ISA Bus Configuration Registers) and they are active LOW. When EADI mode is selected, the pins named LED1, LED2 , and LED3 c hange in function while LED0 continues to indicate 10BASE-T Link Status. LED 1 2 3 EADI Function SF/BD SRD SRDCLK IRQ15/APCS Address PROM Chip Select Output When programmed as APCS in Plug and Play Register F0, this signal is asserted when the external Address PROM is read. When an I/O read operation is performed on the first 16 bytes in the PCnet-ISA II controller’s I/O space, APCS is asserted. The outputs of the external Address PROM drive the PROM Data Bus. The PCnet-ISA II controller buffers the contents of the PROM data bus and drives them on the lower eight bits of the System Data Bus. When programmed to IRQ15 (default), this pin has the same function as IRQ 3, 4, 5, 9, 10, 11, or 12. BPCS Boot PROM Chip Select Output This signal is asserted when the Boot PROM is read. If SA0-19 lines match a predefined address block and MEMR is active and REF inactive, the BPCS signal will be asserted. The outputs of the external Boot PROM drive the PROM Data Bus. The PCnet-ISA II controller buffers the contents of the PROM data bus and drives them on the lower eight bits of the System Data Bus. PRDB3-7 Private Data Bus Input/Output This is the data bus for the Boot PROM and the Address PROM. PRDB2/EEDO Private data bus bit 2/Data Out Input/Output A multifunction pin which serves as PRDB2 of the private data bus and, when ISACSR3 bit 4 is set, changes to become DATA OUT from the EEPROM. DXCVR/EAR Disable Transceiver/ External Address Reject Input/Output PRDB1/EEDI Private data bus bit 1/Data In Input/Output A multifunction pin which serves as PRDB1 of the private data bus and, when ISACSR3 bit 4 is set, changes to become DATA In to the EEPROM. This pin can be used to disable external transceiver circuitry attached to the AUI interface when the internal 10BASE-T port is active. The polarity of this pin is set by the DXCVRP bit (PnP register 0xF0, bit 5). When DXCVRP is cleared (default), the DXCVR pin is driven HIGH when the Twisted Pair port is active or SLEEP mode has been entered and driven LOW when the AUI port is active. When DXCVRP is set, the DXCVR pin is driven LOW when the Twisted Pair port is active or SLEEP mode has been entered and driven HIGH when the AUI port is active. PRDB0/EESK Private data bus bit 0/ Serial Clock Input/Output A multifunction pin which serves as PRDB0 of the private data bus and, when ISACSR3 bit 4 is set, changes to become Serial Clock to the EEPROM. 20 Am79C961A SHFBUSY Shift Busy Input/Output This pin indicates that a read from the external EEPROM is in progress. It is active only when data is being shifted out of the EEPROM due to a hardware RESET or assertion of the EE_LOAD bit (ISACSR3, bit 14). If this pin is left unconnected or pulled low with a pull-down resistor, an EEPROM checksum error is forced. Normally, this pin should be connected to VCC through a 10K Ω pull-up resistor. and proceeds into a power savings mode. All outputs will be placed in their normal reset condition. All PCnet-ISA II controller inputs will be ignored except for the SLEEP pin itself. Deassertion of SLEEP results in the device waking up. The system must delay the starting of the network controller by 0.5 seconds to allow internal analog circuits to stabilize. XTAL1 Crystal Connection Input The internal clock generator uses a 20 MHz crystal that is attached to pins XTAL1 and XTAL2. Alternatively, an external 20 MHz CMOS-compatible clock signal can be used to drive this pin. Refer to the section on External Crystal Characteristics for more details. EECS EEPROM CHIP SELECT Output This signal is asserted when read or write accesses are being performed to the EEPROM. It is controlled by ISACSR3. It is driven at Reset during EEPROM Read. XTAL2 Crystal Connection Output The internal clock generator uses a 20 MHz crystal that is attached to pins XTAL1 and XTAL2. If an external clock is used, this pin should be left unconnected. SLEEP Sleep Input When SLEEP pin is asserted (active LOW), the PCnet-ISA II controller performs an internal system reset Am79C961A 21 22 DVSS3 SMA SA0 SA1 SA2 DVSS10 SA3 SA4 SA5 SA6 SA7 SA8 SA9 DVSS4 SA10 SA11 SA12 SBHE DVDD3 PRAB0 PRAB1 PRAB2 DVSS5 PRAB3 PRAB4 PRAB5 PRAB6 PRAB7 PRAB8 PRAB9 DVSS6 PRAB10 PRAB11 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 CONNECTION DIAGRAMS: BUS SLAVE MODE PQFP 132 Am79C961AKC Am79C961A DVDD4 PRAB12 PRAB13 PRAB14 PRAB15 DVSS7 SA13 SA14 SA15 SRWE AEN IOCHRDY MEMW MEMR DVSS11 APCS/IRQ15 SRCS/IRQ12 IRQ11 DVDD5 IRQ10 IOCS16 BPAM IRQ3 IRQ4 IRQ5 REF DVSS12 SROE SMAM IOR IOW IRQ9 RESET 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 XTAL2 AVSS2 XTAL1 AVDD3 TXD+ TXPD+ TXD– TXPD– AVDD4 RXD+ RXD– DVSS13 SD15 SD7 SD14 SD6 DVSS9 SD13 SD5 SD12 SD4 DVDD7 SD11 SD3 SD10 SD2 DVSS8 SD9 SD1 SD8 SD0 SLEEP DVDD6 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 DVDD2 TCK TMS TDO TDI EECS BPCS SHFBUSY PRDB0/EESK PRDB1/EEDI PRDB2/EEDO PRDB3 DVSS2 PRDB4 PRDB5 PRDB6 PRDB7 DVDD1 LED0 LED1 DVSS1 LED2 LED3 DXCVR/EAR AVDD2 CI+ CI– DI+ DI– AVDD1 DO+ DO– AVSS1 19364B-3 BLOCK DIAGRAM: BUS SLAVE MODE AEN 802.3 MAC Core DXCVR/EAR IOCHRDY IOR IOW IRQ[3, 4, 5, 9, 10, 11, 12] IOCS16 MEMR MEMW REF RESET SA[0-15] SBHE ISA Bus Interface Unit RCV FIFO CI+/Encoder/ Decoder (PLS) & AUI Port XMT FIFO DI+/XTAL1 XTAL2 DO+/- RXD+/10BASE-T MAU TXD+/TXPD+/- SD[0-15] FIFO Control Private Bus Control Buffer Management Unit SMA SLEEP BPAM SMAM SHFBUSY EEDO EEDI EESK EECS IRQ15/APCS BPCS LED[0-3] PRAB[0-15] PRDB[0-7] SROE SRWE TDO EEPROM Interface Unit JTAG Port Control TMS TDI TCK DVDD[1-7] DVSS[1-13] AVDD[1-4] AVSS[1-2] 19364B-4 Am79C961A 23 PIN DESIGNATIONS: BUS SLAVE MODE Listed by Pin Number Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Name DVSS3 SMA SA0 SA1 SA2 DVSS10 SA3 SA4 SA5 SA6 SA7 SA8 SA9 DVSS4 SA10 SA11 SA12 SBHE DVDD3 PRAB0 PRAB1 PRAB2 DVSS5 PRAB3 PRAB4 PRAB5 PRAB6 PRAB7 PRAB8 PRAB9 DVSS6 PRAB10 PRAB11 DVDD4 PRAB12 PRAB13 PRAB14 PRAB15 DVSS7 SA13 SA14 SA15 SRWE AEN Pin # 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 Name IOCHRDY MEMW MEMR DVSS11 IRQ15 IRQ12 IRQ11 DVDD5 IRQ10 IOCS16 BPAM IRQ3 IRQ4 IRQ5 REF DVSS12 SROE SMAM IOR IOW IRQ9 RESET DVDD6 SLEEP SD0 SD8 SD1 SD9 DVSS8 SD2 SD10 SD3 SD11 DVDD7 SD4 SD12 SD5 SD13 DVSS9 SD6 SD14 SD7 SD15 DVSS13 Pin # 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 Name RXDRXD+ AVDD4 TXPDTXDTXPD+ TXD+ AVDD3 XTAL1 AVSS2 XTAL2 AVSS1 DODO+ AVDD1 DIDI+ CICI+ AVDD2 DXCVR/EAR LED3 LED2 DVSS1 LED1 LED0 DVDD1 PRDB7 PRDB6 PRDB5 PRDB4 DVSS2 PRDB3 PRDB2/EEDO PRDB1/EEDI PRDB0/EESK SHFBUSY BPCS EECS TDI TDO TMS TCK DVDD2 24 Am79C961A PIN DESIGNATIONS: BUS SLAVE MODE Listed by Pin Name Name AEN AVDD1 AVDD2 AVDD3 AVDD4 AVSS1 AVSS2 BPAM BPCS CICI+ DIDI+ DODO+ DVDD1 DVDD2 DVDD3 DVDD4 DVDD5 DVDD6 DVDD7 DVSS1 DVSS10 DVSS11 DVSS12 DVSS13 DVSS2 DVSS3 DVSS4 DVSS5 DVSS6 DVSS7 DVSS8 DVSS9 DXCVR/EAR EECS IOCHRDY IOCS16 IOR IOW IRQ10 IRQ11 IRQ12 Pin# 44 103 108 96 91 100 98 55 126 106 107 104 105 101 102 115 132 19 34 52 67 78 112 6 48 60 88 120 1 14 23 31 39 73 83 109 127 45 54 63 64 53 51 50 Name IRQ15 IRQ3 IRQ4 IRQ5 IRQ9 LED0 LED1 LED2 LED3 MEMR MEMW PRAB0 PRAB1 PRAB10 PRAB11 PRAB12 PRAB13 PRAB14 PRAB15 PRAB2 PRAB3 PRAB4 PRAB5 PRAB6 PRAB7 PRAB8 PRAB9 PRDB0/DO PRDB0/D1 PRDB0/SCLK PRDB3 PRDB4 PRDB5 PRDB6 PRDB7 REF RESET RXDRXD+ SA0 SA1 SA10 SA11 SA12 Pin# 49 56 57 58 65 114 113 111 110 47 46 20 21 32 33 35 36 37 38 22 24 25 26 27 28 29 30 124 123 122 121 119 118 117 116 59 66 89 90 3 4 15 16 17 Name SA13 SA14 SA15 SA2 SA3 SA4 SA5 SA6 SA7 SA8 SA9 SBHE SD0 SD1 SD10 SD11 SD12 SD13 SD14 SD15 SD2 SD3 SD4 SD5 SD6 SD7 SD8 SD9 SHFBUSY SLEEP SMA SMAM SROE SRWE TCK TDI TDO TMS TXDTXD+ TXPDTXPD+ XTAL1 XTAL2 Pin# 40 41 42 5 7 8 9 10 11 12 13 18 69 71 75 77 80 82 85 87 74 76 79 81 84 86 70 72 125 68 2 62 61 43 131 128 129 130 93 95 92 94 97 99 Am79C961A 25 PIN DESIGNATIONS: BUS SLAVE MODE Listed by Group Pin Name ISA Bus Interface AEN IOCHRDY IOCS16 IOR IOW IRQ[3, 4, 5, 9, 10, 11, 12, 15] MEMR MEMW REF RESET SA[0–15] SBHE SD[0–15] Board Interfaces IRQ15/APCS BPCS BPAM DXCVR/EAR LED0 LED1 LED2 LED3 PRAB[0–15] PRDB[3–7] SLEEP SMA SMAM SROE SRWE XTAL1 XTAL2 SHFBUSY PRDB(0)/EESK PRDB(1)/EEDI PRDB(2)/EEDO EECS IRQ15 or Address PROM Chip Select Boot PROM Chip Select Boot PROM Address Match Disable Transceiver LED0/LNKST LED1/SFBD/RCVACT LED2/SRD/RXDATD01 LED3/SRDCLK/XMTACT PRivate Address Bus PRivate Data Bus Sleep Mode Slave Mode Architecture Shared Memory Address Match Static RAM Output Enable Static RAM Write Enable Crystal Oscillator Input Crystal Oscillator OUTPUT Read access from EEPROM in process Serial Shift Clock Serial Shift Data In Serial Shift Data Out EEPROM Chip Select O O I I/O O O O O I/O I/O I I I O O I O O I/O I/O I/O O TS3 TS1 TS1 TS2 TS2 TS2 TS2 TS3 TS1 TS1 TS1 Address Enable I/O Channel Ready I/O Chip Select 16 I/O Read Select I/O Write Select Interrupt Request Memory Read Select Memory Write Select Memory Refresh Active System Reset System Address Bus System Byte High Enable System Data Bus I O O I I O I I I I I I I/O TS3 TS3/OD3 OD3 OD3 Pin Function I/O Driver 26 Am79C961A PIN DESIGNATIONS: BUS SLAVE MODE Listed by Group Pin Name Attachment Unit Interface (AUI) CI± DI± DO± Twisted Pair Transceiver Interface (10BASE-T) RXD± TXD± TXPD± 10BASE-T Receive Data 10BASE-T Transmit Data 10BASE-T Predistortion Control I O O Collision Inputs Receive Data Transmit Data I I O Pin Function I/O Driver IEEE 1149.1 Test Access Port Interface (JTAG) TCK TDI TDO TMS Power Supplies AVDD AVSS DVDD DVSS Analog Power [1-4] Analog Ground [1-2] Digital Power [1-7] Digital Ground [1-13] Test Clock Test Data Input Test Data Output Test Mode Select I I O I TS2 Output Driver Types Name TS1 TS2 TS3 OD3 Type Tri-State Tri-State Tri-State Open Drain IOL (mA) 4 12 24 24 IOH (mA) –1 –4 –3 –3 pF 50 50 120 120 Am79C961A 27 PIN DESCRIPTION: BUS SLAVE MODE ISA Interface AEN Address Enable Input This signal must be driven LOW when the bus performs an I/O access to the device. IRQ3, 4, 5, 9, 10, 11, 12, 15 Interrupt Request Output An attention signal which indicates that one or more of the following status flags is set: BABL, MISS, MERR, RINT, IDON or TXSTRT. All status flags have a mask bit which allows for suppression of IRQ assertion. These flags have the following meaning: BABL RCVCCO JAB MISS MERR Babble Receive Collision Count Overflow Jabber Missed Frame Memory Error Missed Packet Count Overflow Receive Interrupt Initialization Done Transmit Start IOCHRDY I/O Channel Ready Output When the PCnet-ISA II controller is being accessed, a HIGH on IOCHRDY indicates that valid data exists on the data bus for reads and that data has been latched for writes. IOCS16 I/O Chip Select 16 Input/Output When an I/O read or write operation is performed, the PCnet-ISA II controller will drive this pin LOW to indicate that the chip supports a 16-bit operation at this address. (If the motherboard does not receive this signal, then the motherboard will convert a 16-bit access to two 8-bit accesses). The PCnet-ISA II controller follows the IEEE P996 specification that recommends this function be implemented as a pure decode of SA0-9 and AEN, with no dependency on IOR, or IOW; however, some PC/AT clone systems are not compatible with this approach. For this reason, the PCnet-ISA II controller is recommended to be configured to run 8-bit I/O on all machines. Since data is moved by memory cycles there is vir tually no performance loss incurred by running 8-bit I/O and compatibility problems are virtually eliminated. The PCnet-ISA II controller can be configured to run 8-bit-only I/ O by clearing Bit 0 in Plug and Play Register F0. MPCO RINT IDON TXSTRT MEMR Memory Read Input ME M R g o es L OW to pe rfo r m a me mo r y r ea d operation. MEMW Memory Write Input MEMW goes LOW to perform a memory write operation. REF Memory Refresh Input When REF is asserted, a memory refresh cycle is in progress. During a refresh cycle, MEMR a ssertion is ignored. IOR I/O Read Input To perform an Input/Output Read operation on the device IOR must be asserted. IOR is only valid if the AEN signal is LOW and the external address matches the PCnet-ISA II controller’s predefined I/O address location. If valid, IOR indicates that a slave read operation is to be performed. RESET Reset Input When RESET is asserted HIGH, the PCnet-ISA II controller performs an internal system reset. RESET must be held for a minimum of 10 XTAL1 periods before being deasserted. While in a reset state, the PCnet-ISA II controller will tristate or deassert all outputs to predefined reset levels. The PCnet-ISA II controller resets itself upon power-up. IOW I/O Write Input To perform an Input/Output write operation on the device IOW must be asserted. IOW is only valid if AEN signal is LOW and the external address matches the PCnet-ISA II controller’s predefined I/O address location. If valid, IOW indicates that a slave write operation is to be performed. SA0-15 System Address Bus Input This bus carries the address inputs from the system address bus. Address data is stable during command active cycle. 28 Am79C961A SBHE System Bus High Enable Input This signal indicates the HIGH byte of the system data bus is to be used. There is a weak pull-up resistor on this pin. If the PCnet-ISA II controller is installed in an 8-bit only system like the PC/XT, SBHE will always be HIGH and the PCnet-ISA II controller will perform only 8-bit operations. There must be at least one LOW going edge on this signal before the PCnet-ISA II controller will perform 16-bit operations. DXCVR/EAR Disable Transceiver/ External Address Reject Input/Output This pin disables the transceiver. The DXCVR output is configured in the initialization sequence. A high level indicates the Twisted Pair Interface is active and the AUI is inactive, or SLEEP mode has been entered. A low level indicates the AUI is active and the Twisted Pair interface is inactive. If EADI mode is selected, this pin becomes the EAR input. The incoming frame will be checked against the internally active address detection mechanisms and the result of this check will be OR’d with the value on the EAR pin. The EAR pin is defined as REJECT. (See the EADI section for details regarding the function and timing of this signal). SD0-15 System Data Bus Input/Output This bus is used to transfer data to and from the PCnet-ISA II controller to system resources via the ISA data bus. SD0-15 is driven by the PCnet-ISA II controller when performing slave read operations. Likewise, the data on SD0-15 is latched by the PCnet-ISA II controller when performing slave write operations. LED0-3 LED Drivers Output These pins sink 12 mA each for driving LEDs. Their meaning is software configurable (see section The ISA Bus Configuration Registers) and they are active LOW. When EADI mode is selected, the pins named LED1, LED2 , and LED3 c hange in function while LED0 continues to indicate 10BASE-T Link Status. The DXCVR input becomes the EAR input. LED 1 2 3 EADI Function SF/BD SRD SRDCLK Board Interface APCS/IRQ15 Address PROM Chip Select Output This signal is asserted when the external Address PROM is read. When an I/O read operation is performed on the first 16 bytes in the PCnet-ISA II controller’s I/O space, APCS is asserted. The outputs of the external Address PROM drive the PROM Data Bus. The PCnet-ISA II controller buffers the contents of the PROM data bus and drives them on the lower eight bits of the System Data Bus. IOCS16 is not asserted during this cycle. BPAM Boot PROM Address Match Input This pin indicates a Boot PROM access cycle. If no Boot PROM is installed, this pin has a default value of HIGH and thus may be left connected to VDD. PRAB0-15 Private Address Bus Input/Output The Private Address Bus is the address bus used to drive the Address PROM, Remote Boot PROM, and SRAM. BPCS Boot PROM Chip Select Output This signal is asserted when the Boot PROM is read. If BPAM is active and MEMR is active, the BPCS signal will be asserted. The outputs of the external Boot PROM drive the PROM Data Bus. The PCnet-ISA II controller buffers the contents of the PROM data bus and drives them on the System Data Bus. IOCS16 is not asserted during this cycle. If 16-bit cycles are performed, it is the responsibility of external logic to assert MEMCS16 signal. PRDB3-7 Private Data Bus Input/Output This is the data bus for the static RAM, the Boot PROM, and the Address PROM. PRDB2/EEDO Private Data Bus Bit 2/Data Out Input/Output A multifunction pin which serves as PRDB2 of the private data bus and, when ISACSR3 bit 4 is set, changes to become DATA OUT from the EEPROM. Am79C961A 29 PRDB1/EEDI Private Data Bus Bit 1/Data In Input/Output A multifunction pin which serves as PRDB1 of the private data bus and, when ISACSR3 bit 4 is set, changes to become DATA In to the EEPROM. cess or Programmed I/O access through the PIOSEL bit (ISACSR2, bit 13). SMAM Shared Memory Address Match Input When the Shared Memory architecture is selected (ISACSR2, bit 13), this pin is an input that indicates an access to shared memory when asserted. The type of access is decided by MEMR or MEMW. When the Programmed I/O architecture is selected, this pin should be permanently tied HIGH. PRDB0/EESK Private Data Bus Bit 0/ Serial Clock Input/Output A multifunction pin which serves as PRDB0 of the private data bus and, when ISACSR3 bit 4 is set, changes to become Serial Clock to the EEPROM. SHFBUSY Shift Busy Input/Output This pin indicates that a read from the external EEPROM is in progress. It is active only when data is being shifted out of the EEPROM due to a hardware RESET or assertion of the EE_LOAD bit (ISACSR3, bit 14). If this pin is left unconnected or pulled low with a pull-down resistor, an EEPROM checksum error is forced. Normally, this pin should be connected to VCC through a 10K Ω pull-up resistor. SROE Static RAM Output Enable Output This pin directly controls the external SRAM’s OE pin. SRCS/IRQ12 Static RAM Chip Select Output This pin directly controls the external SRAM’s chip select (CS) pin when the Flash boot ROM option is selected. When Flash boot ROM option is not selected, this pin becomes IRQ12. EECS EEPROM CHIP SELECT Output This signal is asserted when read or write accesses are being performed to the EEPROM. It is controlled by ISACSR3. It is driven at Reset during EEPROM Read. SRWE/WE Static RAM Write Enable/ Write Enable Output This pin (SRWE) directly controls the external SRAM’s W E p i n w h e n a F l a s h m e m o r y d ev i c e i s n o t implemented. When a Flash memory device is implemented, this pin becomes a global write enable (WE) pin. SLEEP Sleep Input When SLEEP input is asserted (active LOW), the PCnet-ISA II controller performs an internal system reset and proceeds into a power savings mode. All outputs will be placed in their normal reset condition. All PCnet-ISA II controller inputs will be ignored except for the SLEEP pin itself. Deassertion of SLEEP results in the device waking up. The system must delay the starting of the network controller by 0.5 seconds to allow internal analog circuits to stabilize. XTAL1 Crystal Connection Input The internal clock generator uses a 20 MHz crystal that is attached to pins XTAL1 and XTAL2. Alternatively, an external 20 MHz CMOS-compatible clock signal can be used to drive this pin. Refer to the section on External Crystal Characteristics for more details. SMA Slave Mode Architecture Input This pin must be permanently pulled LOW for operation in the Bus Slave mode. It is sampled after the hardware RESET sequence. In the Bus Slave mode, the PCnet-ISA II can be programmed for Shared Memory ac- XTAL2 Crystal Connection Output The internal clock generator uses a 20 MHz crystal that is attached to pins XTAL1 and XTAL2. If an external clock is used, this pin should be left unconnected. 30 Am79C961A PIN DESCRIPTION: NETWORK INTERFACES AUI CI+, CI– Control Input Input This is a differential input pair used to detect Collision (Signal Quality Error Signal). TDO Test Data Output Output This is the test data output path from the PCnet-ISA II controller. TDO is tri-stated when JTAG port is inactive. TMS Test Mode Select Input This is a serial input bit stream used to define the specific boundary scan test to be executed. If left unconnected, this pin has a default value of HIGH. DI+, DI– Data In Input This is a differential receive data input pair to the PCnet-ISA II controller. PIN DESCRIPTION: POWER SUPPLIES All power pins with a “D” prefix are digital pins connected to the digital circuitry and digital I/O buffers. All power pins with an “A” prefix are analog power pins connected to the analog circuitry. Not all analog pins are quiet and special precaution must be taken when doing board layout. Some analog pins are more noisy than others and must be separated from the other analog pins. DO+, DO– Data Out Output This is a differential transmit data output pair from the PCnet-ISA II controller. Twisted Pair Interface RXD+, RXD– Receive Data Input This is the 10BASE-T port differential receive input pair. AVDD1–4 Analog Power (4 Pins) Power Supplies power to analog portions of the PCnet-ISA II controller. Special attention should be paid to the printed circuit board layout to avoid excessive noise on these lines. TXD+, TXD– Transmit Data Output These are the 10BASE-T port differential transmit drivers. TXP+, TXP– Transmit Predistortion Control Output These are 10BASE-T transmit waveform pre-distortion control differential outputs. AVSS1–2 Analog Ground (2 Pins) Power Supplies ground reference to analog portions of PCnet-ISA II controller. Special attention should be paid to the printed circuit board layout to avoid excessive noise on these lines. PIN DESCRIPTION: IEEE 1149.1 (JTAG) TEST ACCESS PORT TCK Test Clock Input This is the clock input for the boundary scan test mode operation. TCK can operate up to 10 MHz. TCK does not have an internal pull-up resistor and must be connected to a valid TTL level of high or low. TCK must not be left unconnected. DVDD1–7 Digital Power (7 Pins) Power Supplies power to digital portions of PCnet-ISA II controller. Four pins are used by Input/Output buffer drivers and two are used by the internal digital circuitry. DVSS1–13 Digital Ground (13 Pins) Power Supplies ground reference to digital portions of PCnet-ISA II controller. Ten pins are used by Input/Output buffer drivers and two are used by the internal digital circuitry. TDI Test Data Input Input This is the test data input path to the PCnet-ISA II controller. If left unconnected, this pin has a default value of HIGH. Am79C961A 31 CONNECTION DIAGRAM TQFP 144 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 Am79C961AVC 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 19364B-5 32 Am79C961A PIN DESIGNATIONS: BUS MASTER MODE (TQFP 144) Listed by Pin Number Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Pin Name NC DVSS3 MASTER DRQ7 DRQ6 DRQ5 DVSS10 DACK7 DACK6 DACK5 LA17 LA18 LA19 LA20 DVSS4 LA21 LA22 LA23 SBHE DVDD3 SA0 SA1 SA2 DVSS5 SA3 SA4 SA5 SA6 SA7 SA8 SA9 DVSS6 SA10 SA11 NC NC Pin No. 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 Pin Name NC DVDD4 SA12 SA13 SA14 SA15 DVSS7 SA16 SA17 SA18 SA19 AEN IOCHRDY MEMW MEMR DVSS11 IRQ15/APCS IRQ12/FlashWE IRQ11 DVDD5 IRQ10 IOCS16 BALE IRQ3 IRQ4 IRQ5 REF DVSS12 DRQ3 DACK3 IOR IOW IRQ9 RESET NC NC Pin No. 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 Pin Name NC DVDD6 SLEEP SD0 SD8 SD1 SD9 DVSS8 SD2 SD10 SD3 SD11 DVDD7 SD4 SD12 SD5 SD13 DVSS9 SD6 SD14 SD7 SD15 DVSS13 RXD– RXD+ AVDD4 TXPD– TXD– TXPD+ TXD+ AVDD3 XTAL1 AVSS2 XTAL2 NC NC Pin No. 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 Pin Name NC AVSS1 DO– DO+ AVDD1 DI– DI+ CI– CI+ AVDD2 DXCVR/EAR LED3 LED2 DVSS1 LED1 LED0 DVDD1 PRDB7 PRDB6 PRDB5 PRDB4 DVSS2 PRDB3 PRDB2/EEDO PRDB1/EEDI PRDB0/EESK SHFBUSY BPCS EECS TDI TDO TMS TCK DVDD2 NC NC Am79C961A 33 PIN DESIGNATIONS: BUS MASTER MODE (TQFP 144) Listed by Pin Name Pin Name AEN AVDD1 AVDD2 AVDD3 AVDD4 AVSS1 AVSS2 BALE BPCS CI+ CI– DACK3 DACK5 DACK6 DACK7 DI+ DI– DO+ DO– DRQ3 DRQ5 DRQ6 DRQ7 DVDD1 DVDD2 DVDD3 DVDD4 DVDD5 DVDD6 DVDD7 DVSS1 DVSS10 DVSS11 DVSS12 DVSS13 DVSS2 Pin No. 48 113 118 103 98 110 105 59 136 117 116 66 10 9 8 115 114 112 111 65 6 5 4 125 142 20 38 56 74 85 122 7 52 64 95 130 Pin Name DVSS3 DVSS4 DVSS5 DVSS6 DVSS7 DVSS8 DVSS9 DXCVR/EAR EECS IOCHRDY IOCS16 IOR IOW IRQ10 IRQ11 IRQ12/FlashWE IRQ15/APCS IRQ3 IRQ4 IRQ5 IRQ9 LA17 LA18 LA19 LA20 LA21 LED0 LED1 LED2 LED3 MASTER MEMR MEMW NC NC NC Pin No. 2 15 24 32 43 80 90 119 137 49 58 67 68 57 55 54 53 60 61 62 69 11 12 13 14 16 124 123 121 120 3 51 50 1 35 36 Pin Name NC NC NC NC NC NC NC NC NC PRDB0/EESK PRDB1/EEDI PRDB2/EEDO PRDB3 PRDB4 PRDB5 PRDB6 PRDB7 REF RESET RXD+ RXD– SA0 SA1 SA10 SA11 SA12 SA13 SA14 SA15 SA16 SA17 SA18 SA19 SA2 SA22 SA23 Pin No. 37 71 72 73 107 108 109 143 144 134 133 132 131 129 128 127 126 63 70 97 96 21 22 33 34 39 40 41 42 44 45 46 47 23 17 18 Pin Name SA3 SA4 SA5 SA6 SA7 SA8 SA9 SBHE SD0 SD1 SD10 SD11 SD12 SD13 SD14 SD15 SD2 SD3 SD4 SD5 SD6 SD7 SD8 SD9 SHFBUSY SLEEP TCK TDI TDO TMS TXD+ TXD– TXPD+ TXPD– XTAL1 XTAL2 Pin No. 25 26 27 28 29 30 31 19 76 78 82 84 87 89 92 94 81 83 86 88 91 93 77 79 135 75 141 138 139 140 102 100 101 99 104 106 34 Am79C961A PIN DESIGNATIONS: BUS SLAVE (PIO AND SHARED MEMORY) MODES (TQFP 144) Listed by Pin Number Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Pin Name NC DVSS3 SMA SA0 SA1 SA2 DVSS10 SA3 SA4 SA5 SA6 SA7 SA8 SA9 DVSS4 SA10 SA11 SA12 SBHE DVDD3 PRAB0 PRAB1 PRAB2 DVSS5 PRAB3 PRAB4 PRAB5 PRAB6 PRAB7 PRAB8 PRAB9 DVSS6 PRAB10 PRAB11 NC NC Pin No. 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 Pin Name NC DVDD4 PRAB12 PRAB13 PRAB14 PRAB15 DVSS7 SA13 SA14 SA15 SRWE AEN IOCHRDY MEMW MEMR DVSS11 IRQ15 IRQ12 IRQ11 DVDD5 IRQ10 IOCS16 BPAM IRQ3 IRQ4 IRQ5 REF DVSS12 SROE SMAM IOR IOW IRQ9 RESET PCMCIA_MODE NC Pin No. 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 Pin Name NC DVDD6 SLEEP SD0 SD8 SD1 SD9 DVSS8 SD2 SD10 SD3 SD11 DVDD7 SD4 SD12 SD5 SD13 DVSS9 SD6 SD14 SD7 SD15 DVSS13 RXDRXD+ AVDD4 TXPDTXDTXPD+ TXD+ AVDD3 XTAL1 AVSS2 XTAL2 NC NC Pin No. 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 Pin Name NC AVSS1 DODO+ AVDD1 DIDI+ CICI+ AVDD2 DXCVR/EAR LED3 LED2 DVSS1 LED1 LED0 DVDD1 PRDB7 PRDB6 PRDB5 PRDB4 DVSS2 PRDB3 PRDB2/ EEDO PRDB1/EEDI PRDB0/EESK SHFBUSY BPCS EECS TDI TDO TMS TCK DVDD2 NC NC Am79C961A 35 PIN DESIGNATIONS: BUS SLAVE (PIO AND SHARED MEMORY) MODES (TQFP 144) Listed by Pin Name Pin Name AEN AVDD1 AVDD2 AVDD3 AVDD4 AVSS1 AVSS2 BPAM BPCS CI+ CI– DI+ DI– DO+ DO– DVDD1 DVDD2 DVDD3 DVDD4 DVDD5 DVDD6 DVDD7 DVSS1 DVSS10 DVSS11 DVSS12 DVSS13 DVSS2 DVSS3 DVSS4 DVSS5 DVSS6 DVSS7 DVSS8 DVSS9 DXCVR/EAR Pin No. 48 113 118 103 98 110 105 59 136 117 116 115 114 112 111 125 142 20 38 56 74 85 122 7 52 64 95 130 2 15 24 32 43 80 90 119 Pin Name EECS IOCHRDY IOCS16 IOR IOW IRQ10 IRQ11 IRQ12 IRQ15 IRQ3 IRQ4 IRQ5 IRQ9 LED0 LED1 LED2 LED3 MEMR MEMW NC NC NC NC NC NC NC NC NC NC NC PCMCIA_MODE PRAB0 PRAB1 PRAB10 PRAB11 PRAB12 Pin No. 137 49 58 67 68 57 55 54 53 60 61 62 69 124 123 121 120 51 50 1 35 36 37 72 73 107 108 109 143 144 71 21 22 33 34 39 Pin Name PRAB13 PRAB14 PRAB15 PRAB2 PRAB3 PRAB4 PRAB5 PRAB6 PRAB7 PRAB8 PRAB9 PRDB0/EESK PRDB1/EEDI PRDB2/EEDO PRDB3 PRDB4 PRDB5 PRDB6 PRDB7 REF RESET RXD+ RXD– SA0 SA1 SA10 SA11 SA12 SA13 SA14 SA15 SA2 SA3 SA4 SA5 SA6 Pin No. 40 41 42 23 25 26 27 28 29 30 31 134 133 132 131 129 128 127 126 63 70 97 96 4 5 16 17 18 44 45 46 6 8 9 10 11 Pin Name SA7 SA8 SA9 SBHE SD0 SD1 SD10 SD11 SD12 SD13 SD14 SD15 SD2 SD3 SD4 SD5 SD6 SD7 SD8 SD9 SHFBUSY SLEEP SMAM SMA SROE SRWE TCK TDI TDO TMS TXD+ TXD– TXPD+ TXPD– XTAL1 XTAL2 Pin No. 12 13 14 19 76 78 82 84 87 89 92 94 81 83 86 88 91 93 77 79 135 75 66 3 65 47 141 138 139 140 102 100 101 99 104 106 36 Am79C961A BLOCK DIAGRAM: PCMCIA MODE REG CE2 CE1 WAIT INPACK STSCHG IORD IOWR IREQ IOIS16 OE WE VCC RESET A[0-15] FIFO Control Private Bus Control 10BASE-T MAU PCMCIA Bus Interface Unit RCV FIFO 802.3 MAC Core DXCVR/EAR CI± Encoder/ Decoder (PLS) & AUI Port XMT FIFO DI± XTAL1 XTAL2 DO± RXD± TXD± TXPD± D[0-15] PCMCIA_MODE SMA SLEEP SMAM SHFBUSY EEDO EEDI EESK EECS Buffer Management Unit FLCS LED[0-3] PRAB[0-15] PRDB[0–7] SROE SRWE SRCS TDO EEPROM Interface Unit JTAG Port Control TMS TDI TCK Optional DVDD[1-7] DVSS[1-13] AVDD[1-4] AVSS[1-2] 19364B-6 Am79C961A 37 PIN DESIGNATIONS: PCMCIA MODE (TQFP 144) Listed by Pin Number Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Pin Name NC DVSS3 SMA SA0 SA1 SA2 DVSS10 SA3 SA4 SA5 SA6 SA7 SA8 SA9 DVSS4 SA10 SA11 SA12 CE2 DVDD3 PRAB0 PRAB1 PRAB2 DVSS5 PRAB3 PRAB4 PRAB5 PRAB6 PRAB7 PRAB8 PRAB9 DVSS6 PRAB10 PRAB11 NC NC Pin No. 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 Pin Name NC DVDD4 PRAB12 PRAB13 PRAB14 PRAB15 DVSS7 SA13 SA14 SA15 SRWE REG WAIT WE OE DVSS11 NC SRCS INPACK DVDD5 STSCHG IOIS16 CE1 IREQ NC NC REF DVSS12 SROE SMAM IORD IOWR NC RESET PCMCIA_MODE NC Pin No. 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 Pin Name NC DVDD6 SLEEP SD0 SD8 SD1 SD9 DVSS8 SD2 SD10 SD3 SD11 DVDD7 SD4 SD12 SD5 SD13 DVSS9 SD6 SD14 SD7 SD15 DVSS13 RXD– RXD+ AVDD4 TXPD– TXD– TXPD+ TXD+ AVDD3 XTAL1 AVSS2 XTAL2 NC NC Pin No. 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 Pin Name NC AVSS1 DO– DO+ AVDD1 DI– DI+ CI– CI+ AVDD2 DXCVR/EAR LED3 LED2 DVSS1 LED1 LED0 DVDD1 PRDB7 PRDB6 PRDB5 PRDB4 DVSS2 PRDB3 PRDB2/EEDO PRDB1/EEDI PRDB0/EESK SHFBUSY FLCS EECS TDI TDO TMS TCK DVDD2 NC NC 38 Am79C961A PIN DESIGNATIONS: PCMCIA MODE (TQFP 144) Listed by Pin Name Pin Name AVDD1 AVDD2 AVDD3 AVDD4 AVSS1 AVSS2 CE1 CE2 CI+ CI– DI+ DI– DO+ DO– DVDD1 DVDD2 DVDD3 DVDD4 DVDD5 DVDD6 DVDD7 DVSS1 DVSS10 DVSS11 DVSS13 DVSS2 DVSS3 DVSS4 DVSS5 DVSS6 DVSS7 DVSS8 DVSS9 DXCVR/EAR EECS FLCS Pin No. 113 118 103 98 110 105 59 19 117 116 115 114 112 111 125 142 20 38 56 74 85 122 7 52 95 130 2 15 24 32 43 80 90 119 137 136 Pin Name INPACK IOIS16 IORD IOWR IREQ LED0 LED1 LED2 LED3 NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC OE PCMCIA_MODE PRAB0 PRAB1 PRAB10 PRAB11 PRAB12 PRAB13 PRAB14 PRAB15 PRAB2 PRAB3 Pin No. 55 58 67 68 60 124 123 121 120 1 35 36 37 53 61 62 69 72 73 107 108 109 143 144 51 71 21 22 33 34 39 40 41 42 23 25 Pin Name PRAB4 PRAB5 PRAB6 PRAB7 PRAB8 PRAB9 PRDB0/EESK PRDB1/EEDI PRDB2/EEDO PRDB3 PRDB4 PRDB5 PRDB6 PRDB7 REF REG RESET RXD+ RXD– SA0 SA1 SA10 SA11 SA12 SA13 SA14 SA15 SA2 SA3 SA4 SA5 SA6 SA7 SA8 SA9 SD0 Pin No. 26 27 28 29 30 31 134 133 132 131 129 128 127 126 63 48 70 97 96 4 5 16 17 18 44 45 46 6 8 9 10 11 12 13 14 76 Pin Name SD1 SD10 SD11 SD12 SD13 SD14 SD15 SD2 SD3 SD4 SD5 SD6 SD7 SD8 SD9 SHFBUSY SLEEP SMAM SMAM SRCS SROE SRWE STSCHG TCK TDI TDO TMS TXD+ TXD– TXPD+ TXPD– VSS WAIT WE XTAL1 XTAL2 Pin No. 78 82 84 87 89 92 94 81 83 86 88 91 93 77 79 135 75 64 66 54 65 47 57 141 138 139 140 102 100 101 99 3 49 50 104 106 Am79C961A 39 PIN DESCRIPTION: PCMCIA MODE The PCMCIA pins function as described in the PCMCIA Specification Revision 2.1. Please refer to it for more details. The non-PCMCIA pins used by the 144-pin TQFP package have the same functions as described by “Pin Description: Bus Slave Mode” for ISA operation beginning on page 26 of the Am79C961A PCnet-ISA II data sheet (PID #19364A) with the exception of pin 71, PCMCIA_MODE. PCMCIA_MODE Input Sets the device for PCMCIA operation when tied high. This pin is not available in the 132-pin PQFP package option. 40 Am79C961A PCMCIA vs. ISA Pinout Comparison The pins listed below are pin definition changes specific to PCMCIA mode: In PCMCIA mode, a number of the input pins have internal resistors turned on with a resistance greater than 100 KΩ. These resistors are either connected to V CC o r V SS. The diagram below shows the pin connections for the ISA slave mode and PCMCIA mode. PCMCIA Input Pin Resistance > 100 KΩ to VCC to VCC Pin Number TQFP144 19 48 49 50 51 53 54 55 57 58 59 60 61 62 67 68 69 70 71 75 ISA Slave Mode SBHE AEN IOCHRDY MEMW MEMR IRQ15 IRQ12 IRQ11 IRQ10 IOCS16 BPAM IRQ3 IRQ4 IRQ5 IOR IOW IRQ9 RESET PCMCIA_MODE SLEEP SD0–SD15 SA0–SA15 1 PCMCIA Mode CE2 REG WAIT WE OE NC SRCS INPACK STSCHG IOIS16 CE1 IREQ NC NC IORD IOWR NC RESET PCMCIA_MODE SLEEP3 D0–D15 A0–A15 2 to VCC to VCC to VCC to VCC to VCC to VCC to GND to GND PCMCIA Pin Specification Changes In ISA mode, the IOCHRDY and IOCS16 signals are defined as Open Drain outputs. In PCMCIA mode, the WAIT and IOIS16 s ignals are full CMOS drivers. In PCMCIA mode, the Max values for t IOR8, t MR8 and tSFR10 c hange from 10 ns to –40 ns. — PCMCIA-MODE1 should be tied to VSS in ISA slave mode — PCMCIA-MODE2 should be tied to VCC in PCMCIA mode — SLEEP3 pin remains functional in PCMCIA mode, it is recommended to tie it to VCC Am79C961A 41 PCMCIA MODE BLOCK DIAGRAM [0] A[1–19] A[0] WE CS D[0–7] Flash/EPROM 120 ns OE SA[0–15] System Address Bus PCMCIA Bus PCMCIA Control PCnet-ISA II Controller PRDB[0–7] FLCS SROE PRAB[0–15] A[0–15] SRWE 16-Bit System Data SD[0–15] SMAM SRCS WE CS SRAM 70 ns D[0–7] OE (Upper Address pin) 19364B-7 Note: SMAM shown only for Shared Memory architecture designs. SMAM should be tied HIGH on the PCnet-ISA II for Programmed I/O architecture designs in order to access the flash memory at common memory location zero. Plug and Play Compatible with Flash Memory Support 42 Am79C961A FUNCTIONAL DESCRIPTION PCMCIA Operation When a PCMCIA card is first plugged into a PCMCIA host, all PCMCIA cards respond as a memory only device. In the PCMCIA standard there are two memory spaces, common memory and attribute memory. The REG pin determines which memory space is selected. After the host detects that the PCMCIA card is inserted, the host reads a section of the attribute memory called the CIS (Card Information Structure) which provides configuration information about the inserted card. The attribute memory is a byte wide memory which is only addressable on even bytes. Consequently, odd byte accesses are not defined for attribute memory. Mapped in the CIS area are four Card Configuration Registers which are physically located inside the PCnet-ISA II device. In the PCnet-ISA II device there are four registers which are located at decimal byte address 1008, 1010, 1012 and 1014, respectively. Inside the CIS data structure, there is information which provides the base address of the Card Configuration Registers. Inside first Card Configuration Register is a configuration index region which allows programming the device to support I/O accesses. The PCnet-ISA II supports PCMCIA’s Independent I/O address window mechanism. When I/O Enable is set in the CCR 0 register the PCnet-ISA II controller will respond to I/O commands. The lower 5 address bits decode register accesses. The PCMCIA host is expected to decode I/O address bits 6 and above and only assert CE1 and/or CE2 if the upper I/O address lines match. After the host has mapped the PCMCIA’s card resources to the system, the card should be visible by the system and the driver may be loaded. EEPROM. For cost purposes, it is recommended to place the IEEE address in the CIS (Card Information Structure) Attribute Memory. Flash Memory Map The PCnet-ISA II device supports either a single Flash or EPROM device. The external flash device contains the CIS area as well as an area located in common memory used to hold software drivers. The attribute memory origin is located at byte 0. The common memory region is accessed when REG is deasserted and an access to common memory occurs. SMAM is normally connected to an upper address line on the PCMCIA card. When a high order address is asserted the Flash Memory will be selected. Accesses to common memory when SMAM is low will access the Shared RAM when Shared Memory mode is selected. If Programmed I/O mode is used, the SMAM can be tied high which will result in the Flash’s base address being mapped to location zero. Flash Memory Programming The Flash Memory device can be read at anytime. In order to program the flash device, the APWEN bit must be set in ISACSR2 register to allow write operations to the Flash or non-volatile EEPROM device. Shared Memory vs. Programmed I/O Implications The PCnet-ISA II controller in PCMCIA modes allows for the local packet buffer memory to be mapped into common memory or indirectly accessed through I/O accesses. If shared memory is chosen, the local SRAM will be mapped as a memory resource. Consequently, the CIS will have to indicate this requirement to the system. If Programmed I/O is used no additional memory resources will be required to be allocated by the system. Serial EEPROM Support The Serial EEPROM is not required in PCMCIA mode but can be used to hold the contents of the IEEE address Am79C961A 43 FLASH MEMORY MAP AND CARD REGISTERS 131070 Byte (1FFFEh) Common Memory FLASH Common Memory 1024 Byte (400h) 1022 Byte (3FEh) Reserved 1016 Byte (3F8h) CCR 3 CCR 2 CCR 1 Attribute Memory (Not Available) CIS Data CCR 0 1014 Byte (3F6h) 1012 Byte (3F4h) 1010 Byte (3F2h) 1008 Byte (3F0h) 1006 Byte (3EEh) (Unused) 0 Byte (0h) 19364B-8 44 Am79C961A FUNCTIONAL DESCRIPTION The PCnet-ISA II controller is a highly integrated system solution for the PC-AT ISA architecture. It provides a Full Duplex Ethernet controller, AUI port, and 10BASE-T transceiver. The PCnet-ISA II controller can be directly interfaced to an ISA system bus. The PCnet-ISA II controller contains an ISA bus interface unit, DMA Buffer Management Unit, 802.3 Media Access Control function, separate 136-byte transmit and 128-byte receive FIFOs, IEEE defined Attachment Unit Interface (AUI), and Twisted-Pair Transceiver Media Attachment Unit. In addition, a Sleep function has been incorporated which provides low standby current for power sensitive applications. The PCnet-ISA II controller is register compatible with the LANCE (Am7990) Ethernet controller and PCnet-ISA (Am79C960). The DMA Buffer Management Unit supports the LANCE descriptor software model and the PCnet-ISA II controller is software compatible with the Novell NE2100 and NE1500T add-in cards. External remote boot PROMs and Ethernet physical address PROMs are supported. The location of the I/O registers, Ethernet address PROM, and the boot PROM are determined by the programming of the registers internal to PCnet-ISA II. These registers are loaded at RESET from the EEPROM, if an EEPROM is utilized. Normally, the Ethernet physical address will be stored in the EEPROM with the other configuration data. This reduces the parts count, board space requirements, and power consumption. The option to use a standard parallel 8 bit PROM is provided to manufactures who are concer ned about the non-volatile nature of EEPROMs. The PCnet-ISA II controller’s bus master architecture brings to system manufacturers (adapter card and motherboard makers alike) something they have not been able to enjoy with other architectures—a low-cost system solution that provides the lowest parts count and highest performance. As a bus-mastering device, costly and power-hungry external SRAMs are not needed for packet buffering. This results in lower system cost due to fewer components, less real-estate and less power. The PCnet-ISA II controller’s advanced bus mastering architecture also provides high data throughput and low CPU utilization for even better performance. To offer greater flexibility, the PCnet-ISA II controller has a Bus Slave mode to meet varying application needs. The bus slave mode utilizes a local SRAM memory to store the descriptors and buffers that are located in system memory when in Bus Master mode. The SRAM can be slave accessed on the ISA bus through memory cycles in Shared Memory mode or I/O cycles in Programmed I/O mode. The Shared Memory and Programmed I/O architectures offer maximum compatibility with low-end machines, such as PC/XTs that do not support bus mastering, and very high end machines which require local packet buffering for increased system latency. The network interface provides an Attachment Unit Interface and Twisted-Pair Transceiver functions. Only one interface is active at any particular time. The AUI allows for connection via isolation transformer to 10BASE5 and 10BASE2, thick and thin based coaxial cables. The Twisted-Pair Transceiver interface allows for connection of unshielded twisted-pair cables as specified by the Section 14 supplement to IEEE 802.3 Standard (Type 10BASE-T). Important Note About The EEPROM Byte Map The user is cautioned that while the Am79C961A (PCnet-ISA II) and its associated EEPROM are pin compatible to their predecessors the Am79C961 (PCnet-ISA+) and its associated EEPROM, the byte map structure in each of the EEPROMs are different from each other. The EEPROM byte map structure used for the Am79C961A PCnet-ISA II has the addition of “MISC Config 2, ISACSR9" at word location 10Hex. The EEPROM byte map structure used for the Am79C961 PCnet-ISA+ does not have this. Therefore, should the user intend to replace the PCnet-ISA+ with the PCnet-ISA II, care MUST be taken to reprogram the EEPROM to reflect the new byte map structure needed and used by the PCnet-ISA II. For additional information, refer to the section in this data sheet under EEPROM and the Am79C961 PCnet-ISA+ data sheet (PID #18183) under the sections entitled EEPROM and Serial EEPROM Byte Map. Bus Master Mode System Interface The PCnet-ISA II controller has two fundamental operating modes, Bus Master and Bus Slave. Within the Bus Slave mode, the PCnet-ISA II can be programmed for a Shared Memory or Programmed I/O architecture. The selection of either the Bus Master mode or the Bus Slave mode must be done through hard wiring; it is not software configurable. When in the Bus Slave mode, the selection of the Shared Memory or Programmed I/O architecture is done through software with the PIOSEL bit (ISACSR2, bit 13). The optional Boot PROM is in memory address space and is expected to be 8–64K. On-chip address comparators control device selection is based on the value in the EEPROM. The address PROM, board configuration registers, and the Ethernet controller occupy 24 bytes of I/O space and can be located at 16 different starting addresses. Am79C961A 45 16-Bit System Data SD[0-15] BPCS PRDB[0-7] CE D[0-7] OE ISA Bus PRDB[2]/EEDO PCnet-ISA II PRDB[1]/EEDI Controller PRDB[0]/EESK 24-Bit System Address SA[0-19] LA[17-23] SHFBUSY VCC EECS VCC Boot PROM (Optional) A[0-15] DO DI SK CS ORG EEPROM (Optional, Common) 19364B-9 Bus Master Block Diagram Plug and Play Compatible SD[0-15] 16-Bit System Data PCnet-ISA II Controller BPCS PRDB[0-7] PRDB[0]/EESK PRDB[1]/EEDI PRDB[2]/EEDO EECS A[0-4] D[0-7] IEEE Address PROM (Optional) G 24-Bit System Address ISA Bus SA[0-19] LA[17-23] A[0-15] D[0-7] Flash (Optional) OE WE IRQ15/APCS IRQ12/FlashWE SHFBUSY VCC CS SK DI DO CS EEPROM (Optional, Common) ORG VCC 19364B-10 Bus Master Block Diagram Plug and Play Compatible with Flash and parallel Address PROM Support 46 Am79C961A Bus Slave Mode System Interface The Bus Slave mode is the other fundamental operating mode available on the PCnet-ISA II controller. Within the Bus Slave mode, the PCnet-ISA II can be programmed for a Shared Memory or Programmed I/O architecture. In the Bus Slave mode the PCnet-ISA II controller uses the same descriptor and buffer architecture as in the Bus Master mode, but these data structures are stored in a static RAM controlled by the PCnet-ISA II controller. When operating with the Shared Memory architecture, the local SRAM is visible as a memory resource on the PC which can be accessed through memory cycles on the ISA bus interface. When operating with the Programmed I/O architecture, the local SRAM is accessible through I/O cycles on the ISA bus. Specifically, the SRAM is accessible using the RAP and IDP I/O ports to access the ISACSR0 and ISACSR1 registers, which serve as the SRAM Data port and SRAM Address Pointer port, respectively. In the Bus Slave mode, the PCnet-ISA II registers and optional Ethernet physical address PROM look the same and are accessed in the same way as in the Bus Master mode. The Boot PROM is selected by an external device which drives the Boot PROM Address Match (BPAM) input to the PCnet-ISA II controller. The PCnet-ISA II controller can perform two 8-bit accesses from the 8-bit Boot PROM and present 16-bits of data to accommodate 16 bit read accesses on the ISA bus. When using the Shared Memory architecture mode, access to the local SRAM works the same way as access to the Boot PROM, with an external device generating the Shared Memory Address Match (SMAM) signal and the PCnet-ISA II controller performing the SRAM read or write and the 8/16 bit data conversion. External logic must also drive MEMCS16 appropriately for the 128Kbyte segment decoded from the LA[23:17] signals. The Programmed I/O architecture mode uses the RAP and IDP ports to allow access to the local SRAM hence, external address decoding is not necessary and the SMAM pin is not used in Programmed I/O architecture mode (SMAM s hould be tied HIGH in the Programmed I/O architecture mode). Similar to the Shared Memory architecture mode, in the Programmed I/O architecture mode, 8/16 bit conversion occurs when 16 bit reads and writes are performed on the SRAM Data Port (ISACSR1). Converting the local SRAM accesses from 8-bit cycles to 16-bit cycles allows use of the much faster 16-bit cycle timing while cutting the number of bus cycles in half. This raises performance to more than 400% of what could be achieved with 8-bit cycles. When the Shared Memory architecture mode is used, converting boot PROM accesses to 16-bit cycles allows the two memory resources to be in the same 128 Kbyte block of memory without a clash between two devices with different data widths. The PCnet-ISA II prefetches data from the SRAM to allow fast, minimum wait-state read accesses of consecutive SRAM addresses. In both the Shared Memory architecture and the Programmed I/O architecture, prefetch data is read from a speculated address that assumes that successive reads in time will be from adjacent ascending addresses in the SRAM. At the beginning of each SRAM read cycle, the PCnet-ISA II determines whether the prefetched data can be assumed to be valid. If the prefetched data can be assumed to be valid, it is driven onto the ISA bus without inserting any wait states. If the prefetched data cannot be assumed to be valid, the PCnet-ISA II will insert wait states into the ISA bus read cycle until the correct word is read from the SRAM. Am79C961A 47 A[0–15] Flash (Optional) D[0–7] 16-Bit System Data SD[0] PRAB[0-15] PRDB[0] BPCS SROE PRDB[2]/EEDO PRDB[1]/EEDI PRDB[0]/EESK WE CS OE 24-Bit System Address PCnet-ISA II Controller SA[0] DO DI SK CS ORG EEPROM VCC EECS SRWE SHFBUSY SMAM BPAM IRQ12/SRCS ISA Bus A[0-15] SRAM WE CS OE D[0-7] MEMCS16 SIN VCC CLK BPAM External Glue Logic SMAM SHFBUSY SA[16] LA[17-23] 19364B-11 Note: SMAM shown only for Shared Memory architecture designs. SMAM should be tied HIGH on the PCnet-ISA II for Programmed I/O architecture designs. Bus Slave Block Diagram Plug and Play Compatible with Flash Memory Support 48 Am79C961A PLUG AND PLAY Plug and Play is a standardized method of configuring jumperless adapter cards in a system. Plug and Play is a Microsoft standard and is based on a central software configuration program, either in the operating system or elsewhere, which is responsible for configuring all Plug and Play cards in a system. Plug and Play is fully supported by the PCnet-ISA II ethernet controller. For a copy of the Microsoft Plug and Play specification contact Microsoft Inc. This specification should be referenced in addition to PCnet-ISA II Technical Reference Manual and this data sheet. Port Name ADDRESS WRITE-DATA Location 0X279 (Printer Status Port) 0xA79 (Printer status port + 0x0800) Relocatable in range 0x0203-0x03FF Type Write-only Write-only READ-DATA Read-only Operation If the PCnet-ISA II ethernet controller is used to boot off the network, the device will come up active at RESET, otherwise it will come up inactive. Information stored in the serial EEPROM is used to identify the card and to describe the system resources required by the card, such as I/O space, Memory space, IRQs and DMA channels. This information is stored in a standardized Read Only format. Operation of the Plug and Play system is shown as follows: s Isolate the Plug and Play card s Read the cards resource data s Identify the card s Configure its resources The Plug and Play mode of operation allows the following benefits to the end user. s Eliminates all jumpers or dip switches from the adapter card s Ease of use is greatly enhanced s Allows the ability to uniquely address identical cards in a system, without conflict s Allows the software configuration program or OS to read out the system resource requirements required by the card s Defines a mechanism to set or modify the current configuration of each card s Maintain backward compatibility with other ISA bus adapters The address and Write_DATA ports are located at fixed, predefined I/O addresses. The Write_Data port is located at an alias of the Address port. All three auto-configuration ports use a 12-bit ISA address decode. The READ_DATA port is relocatable within the range 0 x 2 0 3 – 0 x 3 F F by a c o m m a n d w r i t t e n t o t h e WRITE_DATA port. ADDRESS PORT The internal Plug and Play registers are accessed by writing the address to the ADDRESS PORT and then either reading the READ_DATA PORT or writing to the WRITE_DATA PORT. Once the ADDRESS PORT has been written, any number of reads or writes can occur without having to rewrite the ADDRESS PORT. The ADDRESS PORT is also the address to which the initiation key is written to, which is described later. WRITE_DATA PORT The WRITE_DATA PORT is the address to which all writes to the internal Plug and Play registers occur. The destination of the data written to the WRITE_DATA PORT is determined by the last value written to the ADDRESS PORT. READ_DATA PORT The READ_DATA PORT is used to read information from the internal Plug and Play registers. The register to be read is determined by the last value of the ADDRESS PORT. The I/O address of the READ_DATA PORT is set by writing the chosen I/O location to Plug and Play Register 0. The isolation protocol can determine that the address chosen is free from conflict with other devices I/O ports. Auto-Configuration Ports Three 8 bit I/O ports are used by the Plug and Play configuration software on each Plug and Play device to communicate with the Plug and Play registers. The ports are listed in the table below. The software configuration space is defined as a set of 8 bit registers. These registers are used by the Plug and Play software configuration to issue commands, access the resource information, check status, and configure the PCnet-ISA II controller hardware. Initiation Key The PCnet-ISA II controller is disabled at reset when operating in Plug and Play mode. It will not respond to any memory or I/O accesses, nor will the PCnet-ISA II controller drive any interrupts or DMA channels. The initiation key places the PCnet-ISA II device into the configuration mode. This is done by writing a predefined pattern to the ADDRESS PORT. If the proper sequence of I/O writes are detected by the PCnet-ISA II device, the Plug and Play auto-configuration ports Am79C961A 49 are enabled. This pattern must be sequential, i.e., any other I/O access to this I/O port will reset the state machine which is checking the pattern. Interrupts should be disabled during this time to eliminate any extraneous I/O cycles. The exact sequence for the initiation key is listed below in hexadecimal. 6A, B5, DA, ED, F6, FB, 7D, BE DF, 6F, 37, 1B, 0D, 86, C3, 61 B0, 58, 2C, 16, 8B, 45, A2, D1 E8, 74, 3A, 9D, CE, E7, 73, 39 The key element of this mechanism is that each card contains a unique number, referred to as the serial identifier for the rest of the discussion. The serial identifier is a 72-bit unique, non-zero, number composed of two, 32-bit fields and an 8-bit checksum. The first 32-bit field is a vendor identifier. The other 32 bits can be any value, for example, a serial number, part of a LAN address, or a static number, as long as there will never be two cards in a single system with the same 64 bit number. The serial identifier is accessed bit-serially by the isolation logic and is used to differentiate the cards. Isolation Protocol A simple algorithm is used to isolate each Plug and Play card. This algorithm uses the signals on the ISA bus and requires lock-step operation between the Plug and Play hardware and the isolation software. Checksum Serial Vendor Number ID Byte Byte Byte Byte Byte Byte Byte Byte Byte 0 3 2 1 0 3 2 1 0 Shift 19364B-13 Shifting of Serial Identifier State Isolation Read from serial isolation register Yes Get one bit from serial identifier No The shift order for all Plug and Play serial isolation and resource data is defined as bit[0], bit[1], and so on through bit[7]. Hardware Protocol The isolation protocol can be invoked by the Plug and Play software at any time. The initiation key, described earlier, puts all cards into configuration mode. The hardware on each card expects 72 pairs of I/O read accesses to the READ_DATA por t. The card ’ s response to these reads depends on the value of each bit of the serial identifier which is being examined one bit at a time in the sequence shown above. If the current bit of the serial identifier is a “1", then the card will drive the data bus to 0x55 to complete the first I/O read cycle. If the bit is “0", then the card puts its data bus driver into high impedance. All cards in high impedance will check the data bus during the I/O read cycle to sense if another card is driving D[1:0] to “01". During the second I/O read, the card(s) that drove the 0x55, will now drive a 0xAA. All high impedance cards will check the data bus to sense if another card is driving D[1:0] to “10". Between pairs of Reads, the software should wait at least 30 µs. If a high impedance card sensed another card driving the data bus with the appropriate data during both cycles, then that card ceases to participate in the current iteration of card isolation. Such cards, which lose out, will participate in future iterations of the isolation protocol. 19364B-12 ID bit = “1H” Drive “55H” on SD[7:0] Leave SD in high-impedance No SD[1:0] = “01" Yes Wait for next read from serial isolation register Drive “AAH” on SD[7:0] Leave SD in high-impedance No After I/O read completes, fetch next ID bit from serial identifier No Read all 72 bits from serial identifier Yes One Card Isolated SD[1:0] = “10" Yes ID = 0; other card ID = 1 State Sleep Plug and Play ISA Card Isolation Algorithm Note: During each read cycle, the Plug and Play hardware drives the entire 8-bit databus, but only checks the lower 2 bits. 50 Am79C961A If a card was driving the bus or if the card was in high impedance and did not sense another card driving the bus, then it should prepare for the next pair of I/O reads. The card shifts the serial identifier by one bit and uses the shifted bit to decide its response. The above sequence is repeated for the entire 72-bit serial identifier. At the end of this process, one card remains. This card is assigned a handle referred to as the Card Select Number (CSN) that will be used later to select the card. Cards which have been assigned a CSN will not participate in subsequent iterations of the isolation protocol. Cards must be assigned a CSN before they will respond to the other commands defined in the specification. It should be noted that the protocol permits the 8-bit checksum to be stored in non-volatile memory on the card or generated by the on-card logic in real-time. The same LFSR algorithm described in the initiation key section of the Plug and Play specification is used in the checksum generation. During the first 64 bits, software generates a checksum using the received data. The checksum is compared with the checksum read back in the last 8 bits of the sequence. There are two other special considerations for the software protocol. During an iteration, it is possible that the 0x55 and 0xAA combination is never detected. It is also possible that the checksum does not match If either of these cases occur on the first iteration, it must be assumed that the READ_DATA port is in conflict. If a conflict is detected, then the READ_DATA port is relocated. The above process is repeated until a nonconflicting location for the READ_DATA port is found. The entire range between 0x203 and 0x3FF is available, however in practice it is expected that only a few locations will be tried before software determines that no Plug and Play cards are present. During subsequent iterations, the occurrence of either of these two special cases should be interpreted as the absence of any further Plug and Play cards (i.e. the last card was found in the previous iteration). This terminates the isolation protocol. Note: The software must delay 1 ms prior to starting the first pair of isolation reads, and must wait 250 µsec between each subsequent pair of isolation reads. This delay gives the ISA card time to access information from possibly very slow storage devices. Software Protocol The Plug and Play software sends the initiation key to all Plug and Play cards to place them into configuration mode. The software is then ready to perform the isolation protocol. The Plug and Play software generates 72 pairs of l/O read cycles from the READ_DATA port. The software checks the data returned from each pair of I/O reads for the 0x55 and 0xAA driven by the hardware. If both 0x55 and 0xAA are read back, then the software assumes that the hardware had a “1" bit in that position. All other results are assumed to be a “0.” Plug and Play Card Control Registers The state transitions and card control commands for the PCnet-ISA II controller are shown in the following figure. Am79C961A 51 Power up RESET_DRV Set CSN = 0 State Wait for Key Active Commands no active commands Initiation Key State Active Commands Reset Wait for Key Wake[CSN] Sleep Lose serial location OR WAKE CSN (WAKE CSN) State Active Commands Reset Wait for Key Set RD_DATA Port Serial Isolation Wake[CSN] Set CSN State Active Commands Reset Wait for Key Wake[CSN] Resource Data Status Logical Device I/O Range Check Activate Configuration Registers Isolation Config Notes: 1. CSN = Card Select Number. 2. RESET_DRV causes a state transition from the current state to Wait for Key and sets all CSNs to zero. All logical devices are set to their power-up configuration values. 3. The Wait for Key command causes a state transition from the current state to Wait for Key. 19364B-13 Plug and Play ISA Card State Transitions Plug and Play Registers The PCnet-ISA II controller supports all of the defined Plug and Play card control registers. Refer to the tables on the following pages for detailed information. 52 Am79C961A Plug and Play Standard Registers Name Set RD_DATA Port Address Port Value 0x00 Definition Writing to this location modifies the address of the port used for reading from the Plug and Play ISA cards. Bits[7:0] become I/O read port address bits [9:2]. Reads from this register are ignored. I/O Address bits 11:10 should = 00, and 1:0 = 11. Serial Isolation 0x01 A read to this register causes a Plug and Play card in the Isolation state to compare one bit of the board’s ID. This process is fully described above. This register is read only. Bit[0] - Reset all logical devices and restore configuration registers to their power-up values. Bit[1] - Return to the Wait for Key state Bit[2] - Reset CSN to 0 A write to bit[0] of this register performs a reset function on all logical devices. This resets the contents of configuration registers to their default state. All card’s logical devices enter their default state and the CSN is preserved. A write to bit[1] of this register causes all cards to enter the Wait for Key state but all CSNs are preserved and logical devices are not affected. A write to bit[2] of this register causes all cards to reset their CSN to zero. This register is write-only. The values are not sticky, that is, hardware will automatically clear them and there is no need for software to clear the bits. Wake[CSN] 0x03 A write to this port will cause all cards that have a CSN that matches the write data[7:0] to go from the Sleep state to either the Isolation state if the write data for this command is zero or the Config state if the write data is not zero. This register is write-only. Writing to this register resets the EEPROM pointer to the beginning of the Plug and Play Data Structure. A read from this address reads the next byte of resource information. The Status register must be polled until bit[0] is set before this register may be read. This register is read-only. Bit[0] when set indicates it is okay to read the next data byte from the Resource Data register. This register is read-only. A write to this port sets a card’s CSN. The CSN is a value uniquely assigned to each ISA card after the serial identification process so that each card may be individually selected during a Wake [CSN] command. This register is read/write. Selects the current logical device. This register is read only. The PCnet-ISA II controller has only 1 logical device, and this register contains a value of 0x00 Config Control 0x02 Resource Data 0x04 Status Card Select Number 0x05 0x06 Logical Device Number 0x07 Am79C961A 53 PLUG AND PLAY LOGICAL DEVICE CONFIGURATION REGISTERS The PCnet-ISA II controller supports a subset of the defined Plug and Play logical device control registers. The reason for only supporting a subset of the registers is that the PCnet-ISA II controller does not require as many system resources as Plug and Play allows. For instance, Memory Descriptor 2 is not used, as the PCnet-ISA II controller only requires two memor y descriptors, one for the Boot PROM/Flash, and one for the SRAM in Shared Memory Mode. Plug and Play Logical Device Control Registers Name Activate Address Port Value 0x30 Definition For each logical device there is one activate register that controls whether or not the logical device is active on the ISA bus. Bit[0], if set, activates the logical device. Bits[7:1] are reserved and must be zero. This is a read/write register. Before a logical device is activated, I/O range check must be disabled. This register is used to perform a conflict check on the I/O port range programmed for use by a logical device. Bit[7:2] Reserved Bit 1[1] Enable I/O Range check, if set then I/O Range Check is enabled. I/O range check is only valid when the logical device is inactive. Bit[0], if set, forces the logical device to respond to I/O reads of the logical device’s assigned I/O range with a 0x55 when I/O range check is in operation. If clear, the logical device drives 0xAA. This register is read/write. Memory Space Configuration Name Memory base address bits[23:16] descriptor 0 Memory base address bits [15:08] descriptor 0 Memory control Register Index 0x40 0x41 0x42 Definition Read/write value indicating the selected memory base address bits[23:16] for memory descriptor 0. This is the Boot Prom Space. Read/write value indicating the selected memory base address bits[15:08] for memory descriptor 0. Bit[1] specifies 8/16-bit control. The encoding relates to memory control (bits[4:3]) of the information field in the memory descriptor. Bit[0], =0, indicates the next field is used as a range length for decode (implies range length and base alignment of memory descriptor are equal). Bit[0] is read-only. Memory upper limit address; bits [23:16] or range length; bits [15:08] for descriptor 0 Memory upper limit bits [15:08] or range length; bits [15:08] for descriptor 0 Memory descriptor 1 0x43 Read/write value indicating the selected memory high address bits[23:16] for memory descriptor 0. If bit[0] of memory control is 0, this is the range length. If bit[0] of memory control is 1, this is considered invalid. I/O Range Check 0x31 0x44 Read/write value indicating the selected memory high address bits[15:08] for memory descriptor 0, either a memory address or a range length as described above. 0x48-0x4C Memory descriptor 1. This is the SRAM Space for Shared Memory. I/O Space Configuration Name I/O port base address bits[15:08] descriptor 0 I/O port base address bits[07:00] descriptor 0 Register Index 0x60 Definition Read/write value indicating the selected I/O lower limit address bits[15:08] for I/O descriptor 0. If a logical device indicates it only uses 10 bit encoding, then bits[15:10] do not need to be supported. Read/write value indicating the selected I/O lower limit address bits[07:00] for I/O descriptor 0. 0x61 54 Am79C961A I/O Interrupt Configuration Register Index 0x70 Name Interrupt request level select 0 Definition Read/write value indicating selected interrupt level. Bits[3:0] select which interrupt level used for Interrupt 0. One selects IRQL 1, fifteen selects IRQL fifteen. IRQL 0 is not a valid interrupt selection and represents no interrupt selection. Read/write value indicating which type of interrupt is used for the Request Level selected above. Interrupt request type select 0 0x71 Bit[1] : Level, Bit[0] : Type, 1 = high, 0 = low 1 = level, 0 = edge The PCnet-ISA II controller only supports Edge High and Level Low Interrupts. DMA Channel Configuration Name Register Index Definition Read/write value indicating selected DMA channels. Bits[2:0] select which DMA channel is in use for DMA 0. Zero selects DMA channel 0, seven selects DMA channel 7. DMA channel 4, the cascade channel is used to indicate no DMA channel is active. Read only with a value of 0x04. DMA channel select 0 0x74 DMA channel select 1 0x75 DETAILED FUNCTIONS EEPROM Interface The EEPROM supported by the PCnet-ISA II controller is an industry standard 93C56 2-Kbit EEPROM device which uses a 4-wire interface. This device directly interfaces to the PCnet-ISA II controller through a 4-wire interface which uses 3 of the private data bus pins for Data In, Data Out, and Serial Clock. The Chip Select pin is a dedicated pin from the PCnet-ISA II controller. Note: All data stored in the EEPROM is stored in bit-reversal format. Each word (16 bits) must be written into the EEPROM with bit 15 swapped with bit 0, bit 14 swapped with bit 1, etc. This is a 2-Kbit device organized as 128 x 16 bit words. A map of the device as used in the PCnet-ISA II controller is below. The information stored in the EEPROM is as follows: IEEE address 6 bytes Reserved10 bytes EISA ID4 bytes ISACSRs14 bytes Plug and Play Defaults19 bytes 8-Bit Checksum1 byte External Shift Chain2 bytes Plug and Play Config Info192 bytes Important Note About The EEPROM Byte Map The user is cautioned that while the Am79C961A (PCnet-ISA II) and its associated EEPROM are pin comp at i bl e t o th e i r p r e d ec es s o r s th e A m 7 9 C9 6 1 (PCnet-ISA+) and its associated EEPROM, the byte map structure in each of the EEPROMs are different from each other. The EEPROM byte map structure used for the Am79C961A PCnet-ISA II has the addition of “MISC Config 2, ISACSR9" at word location 10Hex. The EEPROM byte map structure used for the Am79C961 PCnet-ISA+ does not have this. Therefore, should the user intend to replace the PCnet-ISA+ with the PCnet-ISA II, care MUST be taken to reprogram the EEPROM to reflect the new byte map structure needed and used by the PCnet-ISA II. For additional information, refer to the Am79C961 PCnet-ISA+ data sheet (PID #18183) under the sections entitled EEPROM and Serial EEPROM Byte Map. Am79C961A 55 Basic EEPROM Byte Map The following is a byte map of the XXC56 series of EEPROMs used by the PCnet-ISA II E ther net Controller. This byte map is for the case where a non-PCnet Family compatible software driver is implemented. Byte 1 IEEE Address (0h) (Bytes 0 – 5) Byte 3 Byte 5 Byte 7 Byte 9 Byte 11 Byte 13 Byte 15 (8h) EISA Config Reg. (Ah) EISA Byte 1 EISA Byte 3 Byte 0 Byte 2 Byte 4 Byte 6 Byte 8 Byte 10 Byte 12 Byte 14 EISA Byte 0 EISA Byte 2 MSRDA, ISACSR0 MSWRA, ISACSR1 MISC Config 1, ISACSR2 Word Location 0 1 2 3 4 5 6 7 8 9 A B C D E F 10 11 12 13 14 15 16 17 18 19 Vendor Byte 1B 1C 1F 20 RAM Memory I/O Ports Interrupts DMA Channels ROM Memory Internal Registers LED1 Config, ISACSR5 LED2 Config, ISACSR6 LED3 Config, ISACSR7 MISC Config 2, ISACSR9 (11h) PnP 0x61 Pnp 0x71 Unused PnP 0x60 PnP 0x70 PnP 0x74 PnP 0x40 PnP 0x42 PnP 0x44 PnP 0x48 PnP 0x4A PnP 0x4C PnP 0xF0 Plug and Play Reg. PnP 0x41 PnP 0x43 Unused PnP 0x49 PnP 0x4B Unused (1Ah) (1Bh) (1Ch) 8–Bit Checksum External Shift Chain Unused Locations . . (20h) Plug and Play Starting Location Note: Checksum is calculated on words 0 through 0x1Bh (first 56 bytes). 56 Am79C961A AMD Device Driver Compatible EEPROM Byte Map The following is a byte map of the XXC56 series of EEPROMs used by the PCnet-ISA II E thernet Controller. This byte map is for the case where a PCnet Family compatible software driver is implemented. (This byte map is an application reference for use in developing AMD software devices.) Word Location 0 1 2 3 4 5 6 7 8 EISA Config Reg. 9 A B C Internal Registers D E F 10 11 12 13 Plug and Play Reg. 14 15 16 17 18 19 1A 1B 1C 1F 20 Byte 1 Byte 3 Byte 5 Reserved HWID (01H) User Space 1 16-Bit Checksum 1 ASCII W (0 x 57H) EISA Byte 1 EISA Byte 3 Byte 0 Byte 2 Byte 4 Reserved Reserved IEEE Address (Bytes 0–5) ASCII W (0 x 57H) EISA Byte 0 EISA Byte 2 MSRDA, ISACSR0 MSWRA, ISACSR1 MISC Config, ISACR2 LED1 Config, ISACSR5 LED2 Config, ISACSR6 LED3 Config, ISACSR7 MISC Config 2, ISACSR9 PnP 0x61 Pnp 0x71 Unused PnP 0x41 PnP 0x43 Unused PnP 0x49 PnP 0x4B Unused 8-Bit Checksum External Shift Chain Unused Locations PnP 0x60 PnP 0x70 PnP 0x74 PnP 0x40 PnP 0x42 PnP 0x44 PnP 0x48 PnP 0x4A PnP 0x4C PnP 0xF0 Vendor Byte RAM Memory I/O Ports Interrupts DMA Channels ROM Memory . . See Appendix C Plug and Play Starting Location See Appendix C Note: Checksum 1 is calculated on words 0 through 5 plus word 7. Checksum 2 is calculated on words 0 through 0x1Bh (first 56 bytes). Am79C961A 57 Plug and Play Register Map The following chart and its bit descriptions show the internal configuration registers associated with the Plug and Play Register 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x30 0x31 0 0 0 0 0 0 0 0 0 0 0 0 Bit 7 Bit 6 Bit 5 Plug and Play operation. These registers control the configuration of the PCnet-ISA II controller. Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 READ_DATA SERIAL ISOLATION 0 WAKE [CSN] RESOURCE_DATA 0 CSN LOGICAL DEVICE NUMBER 0 0 0 0 0 0 0 IORNG ACTIVATE IORNG 0 0 0 READ STATUS 0 RST CSN WAIT KEY RST ALL READ_DATA SERIAL_ISOLATION RST_CSN WAIT_KEY RST_ALL WAKE [CSN] READ_STATUS RESOURCE_DATA CSN ACTIVATE IORNG Address of Plug and Play READ_DATA Port. Used in the Serial Isolation process. Resets CSN register to zero. Resets Wait for Key State. Resets all logical devices. Will wake up if write data matches CSN Register. Read Status of RESOURCE DATA. Next pending byte read from EEPROM. Plug and Play CSN Value. Indicates that the PCnet-ISA II device should be activated. Bits used to enable the I/O Range Check Command. 58 Am79C961A The following chart and its bit descriptions show the internal command registers associated with the Plug Plug and Play Register 0x60 0x61 0x70 0x71 0x74 0x40 0x41 0x42 0x43 0x44 0x48 0x49 0x4A 0x4B 0x4c 0xF0 Bit 7 0 IOAM2 0 0 0 0 BPAM2 0 1 BPSZ2 0 SRAM2 0 1 SRSZ2 0 Bit 6 0 IOAM1 0 0 0 0 BPAM1 0 1 BPSZ1 0 SRAM1 0 1 SRSZ1 LGCY_EN Bit 5 0 IOAM0 0 0 0 0 BPAM0 0 1 BPSZ0 0 SRAM0 0 1 SRSZ0 DXCVRP Bit 4 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 and Play operation. These registers control the PCnet-ISA II controller Plug and Play operation. Bit 3 0 0 IRQ3 0 0 1 0 0 1 0 1 0 0 1 0 BP_CS Bit 2 0 0 IRQ2 0 DMA2 1 0 0 1 0 1 0 0 1 0 APROM_EN Bit 1 1 0 IRQ1 IRQ_LVL DMA1 0 0 BP_16B 1 0 SRAM4 0 SR16B 1 0 AEN_CS Bit 0 IOAM3 0 IRQ0 IRQ_TYPE DMA0 BPAM3 0 0 BPSZ3 0 SRAM3 0 0 SRSZ3 0 IO_MODE FL_SEL PCnet–ISA II’s Legacy Bit Feature Description The current PCnet-ISA II chip is designed such that it always responds to Plug and Play configuration software. There are situations where this response to the Plug and Play software is undesirable. An example of this is when a fixed configuration is required, or when the only possible resource available for the PCnet-ISA II conflicts with a present but not used resource such as IRQ, or when the chip is used in a system with a buggy PnP BIOS. To function in the situations above, a new feature has been added to the PCnet-ISA II chip. This new feature makes the chip ignore the PnP software’s special initiation key sequence (6A). This will effectively turn the chip into the “Legacy” mode operation, where it will be visible in the I/O space, and only special setup programs will be able to reconfigure it. In case the EEPROM is missing, empty, or corrupted, the chip will still recognize AMD’s special initiation key sequence (6B). To enable this feature, a one has to be written into the LGCY_EN bit, which is bit 6 of the Plug and Play register 0xF0. A preferred method would be set this bit in the Vendor Byte (PnP 0xF0) field of the EEPROM located in word offset 0x1A. Am79C961A 59 Plug & Play Register Locations Detailed Description (Refer to the Plug & Play Register Map above) IOAM[3:0] I/O Address Match to bits [8:5] of SA bus (PnP 0x60–0x61). Controls the base address of PCnet-ISA II. The IOAM will be written with a value from the EEPROM. 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Base Address (Hex) 200 220 240 260 280 2A0 2C0 2E0 300 320 340 360 380 3A0 3C0 3E0 DMA[2:0] 0 1 1 1 1 1 0 1 1 0 register will be written with a value from the EEPROM. {For Bus Master Mode Only} The DRQ signals will not be driven unless Plug and Play activate register bit is set. DMA Channel (DRQ/DACK Pair) 1 1 0 1 0 Channel 3 Channel 5 Channel 6 Channel 7 No DMA Channel 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 IOAM[3:0] 0 0 0 0 0 1 0 1 1 0 1 0 1 1 1 1 0 0 0 0 0 1 0 1 1 0 1 0 1 1 1 1 BPAM[3:0] Boot PROM Address Match to bits [16:13] of SA bus (PnP 0x40–0x41). Selects the location where the Boot PROM Address match decode is started. The BPAM will be written with a value from the EEPROM. Address Location (Hex) C0000 C2000 C4000 C6000 C8000 CA000 CC000 CE000 D0000 D2000 D4000 D6000 D8000 DA000 DC000 DE000 Size Supported (K bytes) 8, 16, 32, 64 8 8, 16 8 8, 16, 32 8 8, 16 8 8, 16, 32, 64 8 8, 16 8 8, 16, 32 8 8, 16 8 IRQ[3:0] IRQ selection on the ISA bus (PnP 0x70). Controls which interrupt will be asserted. ISA Edge sensitive or EISA level mode is controlled by IRQ_TYPE bit in PnP 0x71. Default is ISA Edge Sensitive. The IRQ signals will not be driven unless PnP activate register bit is set. ISA IRQ Pin 1 0 1 1 0 1 1 0 IRQ3 (Default) IRQ4 IRQ5 IRQ9 IRQ10 IRQ11 IRQ12 IRQ15 1 0 0 0 1 1 0 1 IRQ[3:0] 0 0 0 1 1 1 1 1 0 1 1 0 0 0 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 BPAM[3:0] 0 0 0 0 0 1 0 1 1 0 1 0 1 1 1 1 0 0 0 0 0 1 0 1 1 0 1 0 1 1 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 BP_16B Boot PROM 16-bit access (PnP 0x42). Is asserted if Boot PROM cycles should respond as an 16-bit device. In Bus Master mode, all boot PROM cycles will only be 8 bits in width. Boot PROM Size (PnP 0x43–0x44). Selects the size of the boot PROM selected. Boot PROM Size x 1 0 0 0 No Boot PROM Selected 8K 16 K 32 K 64 K x 1 1 0 0 BPSZ[3:0] IRQ Type IRQ Type(PnP 0x71). Indicates the type of interrupt setting; Level is 1, Edge is 0. IRQ Level (PnP 0x71). A read-only register bit that indicates the type of setting, active high or low. Always complement of IRQ_TYPE. See ISA CSR2 (EISA_LVL). DMA Channel Select (PnP 0x74). Controls the DRQ and DMA selection of PCnet-ISA II. The DMA[2:0] BPSZ[3:0] 0 1 1 1 1 x 1 1 1 0 IRQ_LVL DMA[2:0] SRAM[4:0] Static RAM Address Match to bits [17:13] of SA bus (PnP 0x48-0x49). Selects the starting location of the Shared Memory when using the 60 Am79C961A Shared Memory architecture mode. The SRAM[2:0] bits are used for performing address decoding on the SA[15:13] address bits as shown in the table below. S RAM[4] an d SRAM[3] must reflect the external address match logic for SA[17] and SA[16], respectively. The SRAM[4:0] bits are ignored when in the Bus Master mode or in the Programmed I/O Architecture mode. SRAM[2:0] 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 0 0 0 1 1 1 1 SA[15:13] 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 SRAM Size (K bytes) 8, 16, 32, 64 8 8, 16 8 8, 16, 32 8 8, 16 8 PCnet-ISA II will respond to the 6A key sequence if the EEPROM read was successful, otherwise it will respond to the 6B key sequence. DXCVRP DXCVR Polarity. The DXCVRP bit sets the polarity of the DXCVR pin. When DXCVRP is cleared (default), the DXCVR pin is driven HIGH when the Twisted Pair port is active or SLEEP mode has been entered and driven LOW when the AUI port is active. When DXCVRP is set, the DXCVR pin is driven LOW when the Twisted Pair port is active or SLEEP mode has been entered and driven HIGH when the AUI port is active. The DXCVRP should generally be left cleared when the PCnet-ISA II is being used with an external DC-DC conver ter that has an active low enable pin. The DXCVRP should generally be set when the PCnet-ISA II is being used with an external DC-DC converter that has an active high enable pin. IO_MODE I/O Mode. When set to one, the internal selection will respond as a 16-bit port, (i.e. drive IOCS16 pin). When IO_MODE is set to zero, (Default), the internal I/O selection will respond as an 8-bit port. External Decode Logic for I/O Registers. When written with a one, the PCnet-ISA II will use the AEN pin as I/O chip select bar, to allow for external decode logic for the upper address bit of SA [9:5]. The purpose of this pin is to allow I/O locations, not suppor ted with the IOAM[3:0], selection, to be defined outside the range 0x200–0x3F7. When set to a zero, (Default), I/O Selection will use IOAM[3:0]. External Parallel IEEE Address PROM. When set, the IRQ15 pin is reconfigured to be an Address Chip Select low, similar to APCS pin in the existing PCnet-ISA (Am79C960) device. The purpose of this bit is to allow for both a serial EEPROM and parallel PROM to coexist. When APROM_EN is set, the IEEE address located in the serial EEPROM will be ignored and parallel access will occur over the PRDB SR_16B Static RAM 16-bit access (PnP 0x4A). If asserted, the PCnet-ISA II will respond to SRAM cycles as a 16-bit device. This bit should be set if external logic is designed to assert the MEMCS16 signal when accesses to the shared memory are decoded. This bit is ignored when in the Bus Master mode or in the Programmed I/O Architecture mode. Static RAM size (PnP 0x4B-0x4C). Selects the size of the static RAM. The SRSZ[3:0] bits are ignored when in the Bus Master mode or in the Programmed I/O Architecture mode. Shared Memory Size x 1 0 0 0 No Static RAM Selected 8K 16 K 32 K 64 K x 1 1 0 0 AEN_CS SRSZ[3:0] SRSZ[3:0] 0 1 1 1 1 x 1 1 1 0 APROM_EN Vendor Defined Byte (PnP 0xF0) LGCY_EN Legacy mode enable. When written with a one, the PCnet-ISA II will not respond to the Plug and Play initiation key sequence (6A) but will respond to the AMD key sequence (6B). Therefore, it cannot be reconfigured by the Plug and Play software. When set to zero (default), the Am79C961A 61 bus. When APROM_EN is cleared, default state, the IEEE address will be read in from the serial device and written to an internal RAM. When the I/O space of the IEEE PROM is selected, PCnet-ISA II, will access the contents of this RAM for I/O read cycles. I/O wr ite cycles will be ignored. BP_CS Boot PROM Chip Select. When BP_CS is set to one, BALE will act as an external chip select (active low) above bit 15 of the address bus. BALE = 0, will select the boot PROM when MEMR is asserted low if the BP_CS bit is set and BPAM[2:0] match SA[15:13] and BPSZ[3:0] matches the selected size. When BP_CS is set to zero. BALE will act as the normal address latch strobe to capture the upper address bits for memory access to the boot PROM. BP_CS is by default low. The primary purpose of this bit is to allow non-ISA bus applications to support larger Boot PROMS or non-standard Boot PROM/Flash locations. Flash Memory Device Selected. W h e n s e t , t h e B o o t P RO M i s replaced with an external Flash memor y device. In Bus Master M o d e, B P CS i s r e p l a c e d w i t h Flash_OE. IRQ12 becomes Flash _WE . The Flash ’s CS pin is grounded. In shared memory mode, BPCS i s replaced with Flash_CS. IRQ12 becomes Static _RAM _CS pin. The SROE and SRWE signals are connected to both the SRAM and Flash memory devices. FL_SEL is cleared by a reset, which is the default. respond to the same initiation key as Plug and Play supports. Instead, a different key is used to bring PCnet-ISA II controller out of the Wait For Key state. This key is as follows: 6B, 35, 9A, CD, E6, F3, 79, BC 5E, AF, 57, 2B, 15, 8A, C5, E2 F1, F8, 7C, 3E, 9F, 4F, 27, 13 09, 84, 42, A1, D0, 68, 34, 1A Use Without EEPROM In some designs, especially PC motherboard applicat i o n s , i t m ay b e d e s i r a b l e t o e l i m i n a t e t h e EEPROM altogether. This would save money, space, and power consumption. The operation of this mode is similar to when the PCnet-ISA II controller encounters a checksum error, except that to enter this mode the SHFBUSY pin is left unconnected. The device will enter software relocatable mode, and the BIOS on the motherboard can wake up the device, configure it, load the IEEE address (possibly stored in Flash ROM) into the PCnet-ISA II controller, and activate the device. External Scan Chain The External Scan Chain is a set of bits stored in the EEPROM which are not used in the PCnet-ISA II controller but which can be used with external hardware to allow jumperless configuration of external devices. A f t e r R E S E T, t h e P C n e t -I S A I I c o n t r o l l e r begins reading the EEPROM and storing the informat i o n i n r e g i s t e r s i n s i d e t h e P C n e t -I S A I I controller. SHFBUSY is held high during the read of the EEPROM. If external circuitry is added, such as a shift register, which is clocked from SCLK and is attached to DO from the EEPROM, data read out of the EEPROM will be shifted into the shift register. After reading the EEPROM to the end of the External Shift Chain, and if there is a correct checksum, SHFBUSY will go low. This will be used to latch the infor mation from the EEPROM into the shift register. If the checksum is invalid, SHFBUSY will not go low, indicating that the EEPROM may be bad. FL_SEL Checksum Failure After RESET, the PCnet-ISA II controller begins reading the EEPROM and storing the information in registers inside PCnet-ISA II controller. PCnet-ISA II controller does a checksum on word locations 0-1Bh inclusive and if the byte checksum = FFh, then the data read from the EEPROM is considered good. If the checksum is not equal to FFh, then the PCnet-ISA II controller enters what is called software relocatable mode. In software relocatable mode, the device functions the same as in Plug and Play mode, except that it does not Flash PROM Use Instead of using a PROM or EPROM for the Boot PROM, it may be desirable to use a Flash or EEPROM type of device for storing the Boot code. This would allow for in-system updates and changes to the information in the Boot ROM without opening up the PC. It may also be desirable to store statistics or drivers in the Flash device. 62 Am79C961A Interface To use a Flash-type device with the PCnet-ISA II controller, Flash Select is set in register 0F0h of the Plug and Play registers. Flash Select is cleared by RESET (default). In bus master mode, BPCS becomes Flash_OE and IRQ12 becomes Flash_WE. The Flash ROM devices CS pin is connected to ground. In shared memory mode, BPCS becomes Flash_CS and IRQ12 becomes the static RAM Chip Select, and the SROE and SRWE signals are connected to both the SRAM and Flash devices. are received. IOCHRDY is asynchronously driven LOW if the PCnet-ISA II controller needs a wait state. It is released synchronously when the PCnet-ISA II controller is ready. When the PCnet-ISA II controller is the Current Master, all the signals it generates are synchronous to the on-chip 20 MHz clock. DMA Transfers The BIU will initiate DMA transfers according to the type of operation being performed. There are three primary types of DMA transfers: 1. Initialization Block DMA Transfers During initialization, the PCnet-ISA II transfers 12 words from the initialization block in memory to internal registers. These 12 words are transferred through different bus mastership period sequences, depending on whether the TIMER bit (CSR4, bit 13) is set and, if TIMER is set, on the value in the Bus Activity Timer register (CSR82). If the TIMER bit is reset (default), the 12 words are always transferred during three separate bus mastership periods. During each bus mastership period, four words (8 bytes) will be read from contiguous memory addresses. If the TIMER bit is set, the 12 words may be transferred using anywhere from 1 to 3 bus mastership periods, depending on the value of the Bus Activity Timer register (CSR82). During each bus mastership period, a minimum of four words (8 bytes) will be read from contiguous memory addresses. If the TIMER bit is set and the value in the Bus Activity Timer register allows it, 8 or all 12 words of the initialization block are read during a single bus mastership period. 2. Descriptor DMA Transfers Descriptor DMA transfers are performed to read or write to transmit or receive descriptors. All transmit and receive descriptor READ accesses require 3 word reads (TMD1, TMD0, then TMD2 for transmit descriptors and RMD1, RMD0, then RMD2 for receive descriptors). Transmit and receive descr iptor WRITE accesses to unchained descriptors or the last descriptor in a chain (ENP set) require 2 word writes (TMD1 then TMD3 for transmit and RMD1 then RMD3 for receive). Transmit and receive descriptor WRITE accesses to chained descriptors that do not have ENP set require 1 word write (TMD1 for transmit and RMD1 for receive). During descriptor write accesses, only the bytes which need to be written are written, as controlled by the SA0 and SBHE pins. If the TIMER bit is reset (default), all accesses during a single bus mastership period will be either all read or all write and will be to only one descriptor. Hence, when the TIMER bit is reset, the bus mastership periods for Optional IEEE Address PROM Normally, the Ethernet physical address will be stored in the EEPROM with the other configuration data. This reduces the parts count, board space requirements, and power consumption. The option to use a standard parallel 8 bit PROM is provided to manufacturers who a r e c o n c e r n e d a b o u t t h e n o n -vo l a t i l e n a t u r e of EEPROMs. To use a 8 bit parallel PROM to store the IEEE address data instead of stor ing it in the EEPROM, the APROM_EN bit is set in the Plug and Play registers by the EEPROM upon RESET. IRQ15 is redefined by the setting of this bit to be APCS, or ADDRESS PROM CHIP SELECT. This pin is connected to an external 8 bit PROM, such as a 27LS19. The address pins of the PROM are connected to the lower address pins of the ISA bus, and the data lines are connected to the private data bus. In this mode, any accesses to the IEEE address will be passed to the external PROM and the data will be passed through the PCnet-ISA II controller to the system data bus. EISA Configuration Registers The PCnet-ISA II controller has support for the 4-byte EISA Configuration Registers. These are used in EISA systems to identify the card and load the appropriate configuration file for that card. This feature is enabled using bit 10 of ISACSR2. When set to 1, the EISA Configuration registers will be enabled and will be read at I/O location 0xC80–0xC83. The contents of these 4 registers are stored in the EEPROM and are automatically read in at RESET. Bus Interface Unit (BIU) The bus interface unit is a mixture of a 20 MHz state machine and asynchronous logic. It handles two types of accesses; accesses where the PCnet-ISA II controller is a slave and accesses where the PCnet-ISA II controller is the Current Master. In slave mode, signals like IOCS16 are asserted and deasser ted as soon as the appropr iate inputs Am79C961A 63 descriptor accesses are always either 3, 2, or 1 cycles long, depending on which descriptor operation is being performed. If the TIMER bit is set, the 3, 2, or 1 cycles required in a descriptor access may be performed as a part of a bus mastership period in which any combination of descriptor reads and writes and buffer reads and writes are performed. When the TIMER bit is set, the Bus Activity Timer (CSR82) and the bus access requirements of the PCnet-ISA II govern the operations performed during a single bus mastership period. 3. FIFO DMA Transfers FIFO DMA transfers occur when the PCnet-ISA II microcode determines that transfers to and/or from the FIFOs are required. Once the PCnet-ISA II BIU has been granted bus mastership, it will perform a series of consecutive transfer cycles before relinquishing the bus. When the Bus Activity Timer is disabled by clearing the TIMER (CSR4, bit 13) bit, all FIFO DMA transfers within a bus mastership period will be either read or write cycles, and all transfers will be to adjacent, ascending addresses. When the Bus Activity Timer is enabled by setting the TIMER bit, DMA transfers within a bus mastership period may consist of any mixture of read and write cycles, without restriction on the address ordering. This mode of operation allows the PCnet-ISA II to accomplish more during each bus ownership period. The number of data transfer cycles contained within a single bus mastership period is in general dependent on the programming of the DMAPLUS (CSR4, bit 14) and the TIMER (CSR4, bit 13) options. Several other factors will also affect the length of the bus mastership period. The possibilities are as follows: If DMAPLUS = 0 and TIMER = 0, a maximum of 16 transfers to or from the FIFO will be performed by default. This default value may be changed by writing to the DMA Burst Register (CSR80, bits 7:0). Since TIMER = 0, all FIFO DMA transfers within a bus mastership period will be either read or write cycles, and all transfers will be to adjacent, ascending addresses. Note that DMAPLUS = 0 merely sets a maximum value for the number of FIFO transfers that may occur during one bus mastership period. The minimum number of transfers in the bus mastership period will be determined by the settings of the FIFO watermarks and the conditions of the FIFOs, and the value of the Bus Activity Timer (CSR82) if the TIMER bit is set. If DMAPLUS = 1 and TIMER = 0, the bus mastership period will continue until the transmit FIFO is filled to its high threshold (read transfers) or the receive FIFO is emptied to its low threshold (write transfers). Other variables may also affect the end point of the bus mas- tership period in this mode, including the particular conditions existing within the FIFOs, and receive and transmit status conditions. Since TIMER = 0, all FIFO DMA transfers within a bus mastership period will be either read or write cycles, and all transfers will be to adjacent, ascending addresses. If TIMER = 1, the bus mastership period will continue until all “pending bus operations” are completed or until the Bus Activity Timer value (CSR82) has expired. These bus operations may consist of any mixture of descriptor and buffer read and write accesses. If DMAPLUS = 1, “pending bus operations” includes any descriptor accesses and buffer accesses that need to be performed. If DMAPLUS = 0, “pending bus operations” include any descriptor accesses that need to be performed and any buffer accesses that need to be performed up to the limit specified by the DMA Burst Register (CSR80, bits 7:0). Note that when TIMER=1, following a last bus transaction during a bus mastership period, the PCnet-ISA II may keep ownership of the bus for up to approximately 1 µs. The PCnet-ISA II determines whether there are further pending bus operations by waiting approximately 1 µs after the completion of every bus operation (e.g. a descriptor or FIFO access). If, during the 1 µs period, no further bus operations are requested by the internal Buffer Management Unit, the PCnet-ISA II determines that there are no further pending operations and gives up bus ownership. This 1 µs of unused bus ownership time is more than made up for by the efficiency gained by being able to perform any mixture of descriptor and buffer read and write accesses during a single bus ownership period. The FIFO thresholds are programmable (see description of CSR80), as are the DMA Burst Register and Bus Activity Timer values. The exact number of transfer cycles in the case of DMAPLUS = 1 will be dependent on the latency of the system bus to the PCnet-ISA II controller’s DMA request and the speed of bus operation, but will be limited by the value in the Bus Activity Timer register (if the TIMER bit is set), the FIFO condition, and receive and transmit status. Barring a time-out by either of these registers, or exceptional receive and transmit events, or an end of packet signal from the FIFO, the FIFO watermark settings and the extent of Bus Grant latency will be the major factors determining the number of accesses performed during any given arbitration cycle when DMAPLUS = 1. The IOCHRDY response of the memory device will a l s o a f fe c t t h e n u m b e r o f t r a n s fe r s w h e n DMAPLUS = 1, since the speed of the accesses will affect the state of the FIFO. During accesses, the FIFO may be filling or emptying on the network end. A slower memory response will allow additional data to accumulate inside of the FIFO (during write transfers from the receive FIFO). If the accesses are slow enough, a com- 64 Am79C961A plete word may become available before the end of the arbitration cycle and thereby increase the number of transfers in that cycle. The general rule is that the longer the Bus Grant latency or the slower the bus transfer operations (or clock speed) or the higher the transmit watermark or the lower the receive watermark or any combination thereof, the longer will be the average bus mastership period. Buffer Management Unit (BMU) The buffer management unit is a microcoded 20 MHz state machine which implements the initialization block and the descriptor architecture. Initialization PCnet-ISA II controller initialization includes the reading of the initialization block in memory to obtain the operating parameters. The initialization block is read when the INIT bit in CSR0 is set. The INIT bit should be set before or concurrent with the STRT bit to insure correct operation. See previous section “1. Initialization Block DMA Transfer.” Once the initialization block has been read in and processed, the BMU knows where the receive and transmit descriptor rings are. On completion of the read operation and after internal registers have been updated, IDON will be set in CSR0, and an interrupt generated if IENA is set. The Initialization Block is vectored by the contents of CSR1 (least significant 16 bits of address) and CSR2 (most significant 8 bits of address). The block contains the user defined conditions for PCnet-ISA II controller operation, together with the address and length information to allow linkage of the transmit and receive descriptor rings. There is an alternative method to initialize the PCnet-ISA II controller. Instead of initialization via the initialization block in memory, data can be written directly into the appropriate registers. Either method may be used at the discretion of the programmer. If the registers are written to directly, the INIT bit must not be set, or the initialization block will be read in, thus overwriting the previously written information. Please refer to Appendix D for details on this alternative method. Reinitialization The transmitter and receiver section of the PCnet-ISA II controller can be turned on via the initialization block (MODE Register DTX, DRX bits; CSR15[1:0]). The state of the transmitter and receiver are monitored through CSR0 (RXON, TXON bits). The PCnet-ISA II controller should be reinitialized if the transmitter and/ or the receiver were not turned on during the original initialization and it was subsequently required to activate them, or if either section shut off due to the detection of an error condition (MERR, UFLO, TX BUFF error). Reinitialization may be done via the initialization block or by setting the STOP bit in CSR0, followed by writing to CSR15, and then setting the START bit in CSR0. Note that this form of restart will not perform the same in the PCnet-ISA II controller as in the LANCE. In particular, the PCnet-ISA II controller reloads the transmit and receive descriptor pointers (working registers) with their respective base addresses. This means that the software must clear the descriptor’s own bits and reset its descriptor ring pointers before the restart of the PCnet-ISA controller. The reload of descriptor base addresses is performed in the LANCE only after initialization, so a restart of the LANCE without initialization leaves the LANCE pointing at the same descriptor locations as before the restart. Suspend The PCnet-ISA II controller offers a suspend mode that allows easy updating of the CSR registers without going through a full reinitialization of the device. The suspend mode also allows stopping the device with orderly termination of all network activity. The host requests the PCnet-ISA II controller to enter the suspend mode by setting SPND (CSR5, bit 0) to ONE. The host must poll SPND until it reads back ONE to determine that the PCnet-ISA II controller has entered the suspend mode. When the host sets SPND to ONE, the PCnet-ISA II controller first finishes all on-going transmit activity and updates the corresponding transmit descriptor entries. It then finishes all on-going receive activity and updates the corresponding receive descriptor entries. It then sets the read-version of SPND to ONE and enters the suspend mode. In suspend mode, all of the CSR registers are accessible. As long as the PCnet-ISA II controller is not reset while in suspend mode (by asserting the RESET pin, reading the RESET register, or by setting the STOP bit), no reinitialization of the device is required after the device comes out of suspend mode. When SPND is set to ZERO, the PCnet-ISA II controller will leave the suspend mode and will continue at the transmit and receive descriptor ring locations where it had left when it entered the suspend mode. Buffer Management Buffer management is accomplished through message descriptor entries organized as ring structures in memory. There are two rings, a receive ring and a transmit ring. The size of a message descriptor entry is 4 words (8 bytes). Descriptor Rings Each descriptor ring must be organized in a contiguous area of memory. At initialization time (setting the INIT bit in CSR0), the PCnet-ISA II controller reads the user-defined base address for the transmit and receive descriptor rings, which must be on an 8-byte boundary, as well as the number of entries contained in the Am79C961A 65 descriptor rings. By default, a maximum of 128 ring entries is permitted when utilizing the initialization block, which uses values of TLEN and RLEN to specify the transmit and receive descriptor ring lengths. However, the ring lengths can be manually defined (up to 65535) by writing the transmit and receive ring length registers (CSR76,78) directly. Each ring entry contains the following information: s The address of the actual message data buffer in user or host memory s The length of the message buffer s Status information indicating the condition of the buffer Receive descriptor entries are similar (but not identical) to transmit descriptor entries. Both are composed of four registers, each 16 bits wide for a total of 8 bytes. To permit the queuing and de-queuing of message buffers, ownership of each buffer is allocated to either the PCnet-ISA II controller or the host. The OWN bit within the descriptor status information, either TMD or RMD (see section on TMD or RMD), is used for this purpose. “Deadly Embrace” conditions are avoided by the ownership mechanism. Only the owner is permitted to relinquish ownership or to write to any field in the descriptor entry. A device that is not the current owner of a descriptor entry cannot assume ownership or change any field in the entry. Descriptor Ring Access Mechanism At initialization, the PCnet-ISA II controller reads the base address of both the transmit and receive descriptor rings into CSRs for use by the PCnet-ISA II controller during subsequent operation. When transmit and receive functions begin, the base address of each ring is loaded into the current descriptor address registers and the address of the next descriptor entry in the transmit and receive rings is computed and loaded into the next descriptor address registers. 66 Am79C961A N N N N • • 24-Bit Base Address Pointer to Initialization Block • RCV Descriptor Ring RX DESCRIPTOR RINGS CSR1 1st desc. start 2nd desc. start CSR2 RES IADR[23:16] IADR[15:0] RMD0 RMD1 RMD2 RMD0 RMD3 Initialization Block MODE PADR[15:0] PADR[31:16] PADRF[47:32] LADRF[15:0] LADRF[31:16] LADRF[47:32] LADRF[63:48] RDRA[15:0] RLEN TLEN RES RDRA[23:16] TDRA[15:0] TDRA[23:16] RES RCV Buffers Data Buffer 1 Data Buffer 2 Data Buffer N • • • M M M M • RX DESCRIPTOR RINGS XMT Descriptor Ring RX DESCRIPTOR RINGS 1st desc. start 2nd desc. start • • TMD0 TMD1 TMD2 TMD0 TMD3 XMT Buffers Data Buffer 1 Data Buffer 2 Data Buffer M 19364B-15 • • • Initialization Block and Descriptor Rings Polling When there is no channel activity and there is no preor post-receive or transmit activity being performed by the PCnet-ISA II controller then the PCnet-ISA II controller will periodically poll the current receive and transmit descriptor entries in order to ascertain their ownership. If the DPOLL bit in CSR4 is set, then the transmit polling function is disabled. A typical polling operation consists of the following: The PCnet-ISA II controller will use the current receive descriptor address stored internally to vector to the appropriate Receive Descriptor Table Entry (RDTE). It will then use the current transmit descriptor address (stored internally) to vector to the appropriate Transmit Descriptor Table Entry (TDTE). These accesses will be made to RMD1 and RMD0 of the current RDTE and TMD1 and TMD0 of the current TDTE at periodic poll- Am79C961A 67 ing intervals. All information collected during polling activity will be stored internally in the appropriate CSRs. (i.e. CSR18–19, CSR40, CSR20–21, CSR42, CSR50, CSR52). Unowned descriptor status will be internally ignored. A typical receive poll occurs under the following conditions: 1. PCnet-ISA II controller does not possess ownership of the current RDTE and the poll time has elapsed and RXON = 1, or 2. PCnet-ISA II controller does not possess ownership of the next RDTE and the poll time has elapsed and RXON = 1, If RXON = 0, the PCnet-ISA II controller will never poll RDTE locations. If RXON = 1, the system should always have at least one RDTE available for the possibility of a receive event. When there is only one RDTE, there is no polling for next RDTE. A typical transmit poll occurs under the following conditions: 1. PCnet-ISA II controller does not possess ownership of the current TDTE and DPOLL = 0 and TXON = 1 and the poll time has elapsed, or 2. PCnet-ISA II controller does not possess ownership of the current TDTE and DPOLL = 0 and TXON = 1 and a packet has just been received, or 3. PCnet-ISA II controller does not possess ownership of the current TDTE and DPOLL = 0 and TXON = 1 and a packet has just been transmitted. The poll time interval is nominally defined as 32,768 crystal clock periods, or 1.6 ms. However, the poll time register is controlled internally by microcode, so any other microcode controlled operation will interrupt the incrementing of the poll count register. For example, when a receive packet is accepted by the PCnet-ISA II controller, the device suspends execution of the poll-time-incrementing microcode so that a receive m ic r o c o de r o u ti n e may i ns t e ad b e exec u te d . Poll-time-incrementing code is resumed when the receive operation has completely finished. Note, how68 ever, that following the completion of any receive or transmit operation, a poll operation will always be performed. The poll time count register is never reset. Note that if a non-default is desired, then a strict sequence of setting the INIT bit in CSR0, waiting for the IDON bit in CSR0, then writing to CSR47, and then setting STRT in CSR0 must be observed, otherwise the default value will not be overwritten. See the CSR47 section for details. Setting the TDMD bit of CSR0 will cause the microcode controller to exit the poll counting code and immediately perform a polling operation. If RDTE ownership has not been previously established, then an RDTE poll will be performed ahead of the TDTE poll. Transmit Descriptor Table Entry (TDTE) If, after a TDTE access, the PCnet-ISA II controller finds that the OWN bit of that TDTE is not set, then the PCnet-ISA II controller resumes the poll time count and re-examines the same TDTE at the next expiration of the poll time count. If the OWN bit of the TDTE is set, but STP = 0, the PCnet-ISA II controller will immediately request the bus in order to reset the OWN bit of this descriptor; this condition would normally be found following a LCOL or RETRY error that occurred in the middle of a transmit packet chain of buffers. After resetting the OWN bit of this descriptor, the PCnet-ISA II controller will again immediately request the bus in order to access the next TDTE location in the ring. If the OWN bit is set and the buffer length is 0, the OWN bit will be reset. In the LANCE the buffer length of 0 is interpreted as a 4096-byte buffer. It is acceptable to have a 0 length buffer on transmit with STP=1 or STP=1 and ENP = 1. It is not acceptable to have 0 length buffer with STP = 0 and ENP = 1. If the OWN bit is set and the start of packet (STP) bit is set, then microcode control proceeds to a routine that will enable transmit data transfers to the FIFO. If the transmit buffers are data chained (ENP = 0 in the first buffer), then the PCnet-ISA II controller will look ahead to the next transmit descriptor after it has performed at least one transmit data transfer from the first buffer. More than one transmit data transfer may possibly take place, depending upon the state of the transmitter. The transmit descriptor look ahead reads TMD0 first and TMD1 second. The contents of TMD0 and TMD1 will be stored in Next TX Descriptor Address (CSR32), Next TX Byte Count (CSR66) and Next TX Status (CSR67) regardless of the state of the OWN bit. This transmit descriptor lookahead operation is performed only once. If the PCnet-ISA II controller does not own the next TDTE (i.e. the second TDTE for this packet), then it will complete transmission of the current buffer and then Am79C961A update the status of the current (first) TDTE with the BUFF and UFLO bits being set. If DXSUFLO is 0 (bit 6 CSR3), then this will cause the transmitter to be disabled (CSR0, TXON = 0). The PCnet-ISA II controller will have to be restarted to restore the transmit function. The situation that matches this description implies that the system has not been able to stay ahead of the PCnet-ISA II controller in the transmit descriptor ring and therefore, the condition is treated as a fatal error. To avoid this situation, the system should always set the transmit chain descriptor own bits in reverse order. If the PCnet-ISA II controller does own the second TDTE in a chain, it will gradually empty the contents of the first buffer (as the bytes are needed by the transmit operation), perform a single-cycle DMA transfer to update the status (reset the OWN bit in TMD1) of the first descriptor, and then it may perform one data DMA access on the second buffer in the chain before executing another lookahead operation. (i.e. a lookahead to the third descriptor). The PCnet-ISA II controller can queue up to two packets in the transmit FIFO. Call them packet “X ” a nd packet “Y”, where “Y” is after “X”. Assume that packet “X” is currently being transmitted. Because the PCnet-ISA II controller can perform lookahead data transfer over an ENP, it is possible for the PCnet-ISA II controller to update a TDTE in a buffer belonging to packet “ Y ” w hile packet “ X ” i s being transmitted if packet “Y” uses data chaining. This operation will result in non-sequential TDTE accesses as packet “X” completes transmission and the PCnet-ISA II controller writes out its status, since packet “X”’s TDTE is before the TDTE accessed as part of the lookahead data transfer from packet “Y”. This should not cause any problem for properly written software which processes buffers in sequence, waiting for ownership before proceeding. If an error occurs in the transmission before all of the bytes of the current buffer have been transferred, then TMD2 and TMD1 of the current buffer will be written; in that case, data transfers from the next buffer will not commence. Instead, following the TMD2/TMD1 update, the PCnet-ISA II controller will go to the next transmit packet, if any, skipping over the rest of the packet which experienced an error, including chained buffers. This is done by returning to the polling microcode where it will immediately access the next descriptor and find the condition OWN = 1 and STP = 0 as described earlier. In that case, the PCnet-ISA II controller will reset the own bit for this descriptor and continue in like manner until a descriptor with OWN = 0 (no more transmit packets in the ring) or OWN = 1 and STP = 1 (the first buffer of a new packet) is reached. At the end of any transmit operation, whether successful or with errors, and the completion of the descriptor updates, the PCnet-ISA II controller will always perform another poll operation. As described earlier, this poll operation will begin with a check of the current RDTE, unless the PCnet-ISA II controller already owns that descriptor. Then the PCnet-ISA II controller will proceed to polling the next TDTE. If the transmit descriptor OWN bit has a zero value, then the PCnet-ISA II controller will resume poll time count incrementation. If the transmit descriptor OWN bit has a value of ONE, then the PCnet-ISA II controller will begin filling the FIFO with transmit data and initiate a transmission. This end-of-operation poll avoids inserting poll time counts between successive transmit packets. Whenever the PCnet-ISA II controller completes a transmit packet (either with or without error) and writes the status information to the current descriptor, then the TINT bit of CSR0 is set to indicate the completion of a transmission. This causes an interrupt signal if the IENA bit of CSR0 has been set and the TINTM bit of CSR3 is reset. Receive Descriptor Table Entry (RDTE) If the PCnet-ISA II controller does not own both the current and the next Receive Descriptor Table Entry, then the PCnet-ISA II controller will continue to poll according to the polling sequence described above. If the receive descriptor ring length is 1, there is no next descriptor, and no look ahead poll will take place. If a poll operation has revealed that the current and the next RDTE belongs to the PCnet-ISA II controller, then additional poll accesses are not necessary. Future poll operations will not include RDTE accesses as long as the PCnet-ISA II controller retains ownership to the current and the next RDTE. When receive activity is present on the channel, the PCnet-ISA II controller waits for the complete address of the message to arrive. It then decides whether to accept or reject the packet based on all active addressing schemes. If the packet is accepted the PCnet-ISA II controller checks the current receive buffer status register CRST (CSR40) to determine the ownership of the current buffer. If ownership is lacking, then the PCnet-ISA II controller will immediately perform a (last ditch) poll of the current RDTE. If ownership is still denied, then the PCnet-ISA II controller has no buffer in which to store the incoming message. The MISS bit will be set in CSR0 and an interrupt will be generated if IENA = 1 (CSR0) and MISSM = 0 (CSR3). Another poll of the current RDTE will not occur until the packet has finished. If the PCnet-ISA II controller sees that the last poll (either a normal poll or the last-ditch effort described in Am79C961A 69 the above paragraph) of the current RDTE shows valid ownership, then it proceeds to a poll of the next RDTE. Following this poll, and regardless of the outcome of this poll, transfers of receive data from the FIFO may begin. Regardless of ownership of the second receive descriptor, the PCnet-ISA II controller will continue to perform receive data DMA transfers to the first buffer, using burst-cycle DMA transfers. If the packet length exceeds the length of the first buffer, and the PCnet-ISA II controller does not own the second buffer, ownership of the current descriptor will be passed back to the system by writing a zero to the OWN bit of RMD1 and status will be written indicating buffer (BUFF = 1) and possibly overflow (OFLO = 1) errors. If the packet length exceeds the length of the first (current) buffer, and the PCnet-ISA II controller does own the second (next) buffer, ownership will be passed back to the system by writing a zero to the OWN bit of RMD1 when the first buffer is full. Receive data transfers to the second buffer may occur before the PCnet-ISA II controller proceeds to look ahead to the ownership of the third buffer. Such action will depend upon the state of the FIFO when the status has been updated on the first descriptor. In any case, lookahead will be performed to the third buffer and the information gathered will be stored in the chip, regardless of the state of the ownership bit. As in the transmit flow, lookahead operations are performed only once. This activity continues until the PCnet-ISA II controller recognizes the completion of the packet (the last byte of this receive message has been removed from the FIFO). The PCnet-ISA II controller will subsequently update the current RDTE status with the end of packet (ENP) indication set, write the message byte count (MCNT) of the complete packet into RMD2 and overwrite the “current” entries in the CSRs with the “next” entries. or post-message processing. These features include the ability to disable retries after a collision, dynamic FCS generation on a packet-by-packet basis, and automatic pad field insertion and deletion to enforce minimum frame size attributes. The two primary attributes of the MAC engine are: s Transmit and receive message data encapsulation — Framing (frame boundary delimitation, frame synchronization) — Addressing (source and destination address handling) — Error detection (physical medium transmission errors) s Media access management — Medium allocation (collision avoidance) — Contention resolution (collision handling) Transmit and Receive Message Data Encapsulation The MAC engine provides minimum frame size enforcement for transmit and receive packets. When APAD_XMT = 1 (bit 11 in CSR4), transmit messages will be padded with sufficient bytes (containing 00h) to ensure that the receiving station will observe an information field (destination address, source address, length/type, data and FCS) of 64-bytes. When ASTRP_RCV = 1 (bit 10 in CSR4), the receiver will automatically strip pad bytes from the received message by observing the value in the length field, and stripping excess bytes if this value is below the minimum data size (46 bytes). Both features can be independently over-ridden to allow illegally short (less than 64 bytes of packet data) messages to be transmitted and/or received. The use of these features reduce bus bandwidth usage because the pad bytes are not transferred to or from host memory. Framing (frame boundary delimitation, frame synchronization) The MAC engine will autonomously handle the construction of the transmit frame. Once the Transmit FIFO has been filled to the predetermined threshold (set by XMTSP in CSR80), and providing access to the channel is currently permitted, the MAC engine will commence the 7-byte preamble sequence (10101010b, where first bit transmitted is a 1). The MAC engine will subsequently append the Start Frame Delimiter (SFD) byte (10101011b) followed by the serialized data from the Transmit FIFO. Once the data has been completed, the MAC engine will append the FCS (most significant bit first) which was computed on the entire data portion of the message. Note that the user is responsible for the correct ordering and content in each of the fields in the frame, Media Access Control The Media Access Control engine incorporates the essential protocol requirements for operation of a compliant Ethernet/802.3 node, and provides the interface between the FIFO sub-system and the Manchester Encoder/Decoder (MENDEC). This section describes operation of the MAC engine when operating in Half Duplex mode. When in Half Duplex mode, the MAC engine is fully compliant to Section 4 of ISO/IEC 8802-3 (ANSI/IEEE Standard 1990 Second Edition) and ANSI/IEEE 802.3 (1985). When operating in Full Duplex mode, the MAC engine behavior changes as described in the Full Duplex Operation section. The MAC engine provides programmable enhanced features designed to minimize host supervision and pre 70 Am79C961A including the destination address, source address, length/type and packet data. The receive section of the MAC engine will detect an incoming preamble sequence and lock to the encoded clock. The internal MENDEC will decode the serial bit stream and present this to the MAC engine. The MAC will discard the first 8 bits of information before searching for the SFD sequence. Once the SFD is detected, all subsequent bits are treated as part of the frame. The MAC engine will inspect the length field to ensure minimum frame size, strip unnecessary pad characters (if enabled), and pass the remaining bytes through the Receive FIFO to the host. If pad stripping is performed, the MAC engine will also strip the received FCS bytes, although the normal FCS computation and checking will occur. Note that apart from pad stripping, the frame will be passed unmodified to the host. If the length field has a value of 46 or greater, the MAC engine will not attempt to validate the length against the number of bytes contained in the message. If the frame terminates or suffers a collision before 64 bytes of infor mation (after SFD) have been received, the MAC engine will automatically delete the f r a m e f r o m t h e R e c e i v e F I F O, w i t h o u t h o s t intervention. Addressing (source and destination address handling) The first 6 bytes of information after SFD will be interpreted as the destination address field. The MAC engine provides facilities for physical, logical, and broadcast address reception. In addition, multiple physical addresses can be constructed (perfect address filtering) using external logic in conjunction with the EADI interface. Error detection (physical medium transmission errors) The MAC engine provides several facilities which report and recover from errors on the medium. In addition, the network is protected from gross errors due to inability of the host to keep pace with the MAC engine activity. On completion of transmission, the following transmit status is available in the appropriate TMD and CSR areas: s The exact number of transmission retry attempts (ONE, MORE, or RTRY). s Whether the MAC engine had to Defer (DEF) due to channel activity. s Loss of Carrier, indicating that there was an interruption in the ability of the MAC engine to monitor its own transmission. Repeated LCAR errors indicate a p o ten ti a ll y fau l ty tra n sc e ive r or ne two r k connection. s Late Collision (LCOL) indicates that the transmission suffered a collision after the slot time. This is indicative of a badly configured network. Late collisions should not occur in a normal operating network. s Collision Error (CERR) indicates that the transceiver did not respond with an SQE Test message within the predetermined time after a transmission completed. This may be due to a failed transceiver, disconnected or faulty transceiver drop cable, or the fact the transceiver does not support this feature (or the feature is disabled). In addition to the reporting of network errors, the MAC engine will also attempt to prevent the creation of any network error due to the inability of the host to service the MAC engine. During transmission, if the host fails to keep the Transmit FIFO filled sufficiently, causing an underflow, the MAC engine will guarantee the message is either sent as a runt packet (which will be deleted by the receiving station) or has an invalid FCS (which will also cause the receiver to reject the message). The status of each receive message is available in the appropriate RMD and CSR areas. FCS and Framing errors (FRAM) are reported, although the received frame is still passed to the host. The FRAM error will only be reported if an FCS error is detected and there are a non-integral number of bits in the message. The MAC engine will ignore up to seven additional bits at the end of a message (dribbling bits), which can occur under normal network operating conditions. The reception of eight additional bits will cause the MAC engine to de-serialize the entire byte, and will result in the received message and FCS being modified. The PCnet-ISA II controller can handle up to 7 dribbling bits when a received packet terminates. During the reception, the CRC is generated on every serial bit (including the dribbling bits) coming from the cable, although the internally saved CRC value is only updated on the eighth bit (on each byte boundary). The framing error is reported to the user as follows: 1. If the number of the dribbling bits are 1 to 7 and there is no CRC error, then there is no Framing error (FRAM = 0). 2. If the number of the dribbling bits are less than 8 and there is a CRC error, then there is also a Framing error (FRAM = 1). 3. If the number of dribbling bits = 0, then there is no Framing error. There may or may not be a CRC (FCS) error. Counters are provided to report the Receive Collision Count and Runt Packet Count used for network statistics and utilization calculations. Note that if the MAC engine detects a received packet which has a 00b pattern in the preamble (after the first Am79C961A 71 8 bits, which are ignored), the entire packet will be ignored. The MAC engine will wait for the network to go inactive before attempting to receive the next packet. Media Access Management The basic requirement for all stations on the network is to provide fairness of channel allocation. The 802.3/ Ethernet protocol defines a media access mechanism which permits all stations to access the channel with equality. Any node can attempt to contend for the channel by waiting for a predetermined time (Inter Packet Gap interval) after the last activity, before transmitting on the medium. The channel is a multidrop communications medium (with various topological configurations permitted) which allows a single station to transmit and all other stations to receive. If two nodes simultaneously contend for the channel, their signals will interact, causing loss of data (defined as a collision). It is the responsibility of the MAC to attempt to avoid and recover from a collision, to guarantee data integrity for the end-to-end transmission to the receiving station. Medium Allocation (collision avoidance) The IEEE 802.3 Standard (ISO/IEC 8802-3 1990) requires that the CSMA/CD MAC monitor the medium traffic by looking for carrier activity. When carrier is detected the medium is considered busy, and the MAC should defer to the existing message. The IEEE 802.3 Standard also allows optional two part deferral after a receive message. See ANSI/IEEE Std 802.3-1990 Edition, 4.2.3.2.1: “Note: It is possible for the PLS carrier sense indication to fail to be asserted during a collision on the media. If the deference process simply times the interpacket gap based on this indication it is possible for a short interFrame gap to be generated, leading to a potential reception failure of a subsequent frame. To enhance system robustness the following optional measures, as specified in 4.2.8, are recommended when InterFrameSpacingPart1 is other than zero: (1) Upon completing a transmission, start timing the interpacket gap, as soon as transmitting and carrier Sense are both false. (2) When timing an interpacket gap following reception, reset the interpacket gap timing if carrier Sense becomes true during the first 2/3 of the interpacket gap timing interval. During the final 1/3 of the interval the timer shall not be reset to ensure fair access to the medium. An initial period shorter than 2/3 of the interval is permissible including zero.” The MAC engine implements the optional receive two p a r t d e fe r r a l a l g o r i t h m , w i t h a f i r s t p a r t i n ter-frame-spacing time of 6.0 µs. The second part of the inter-frame-spacing interval is therefore 3.6 µs. The PCnet-ISA II controller will perform the two-part deferral algorithm as specified in Section 4.2.8 (Process Deference). The Inter Packet Gap (IPG) timer will start timing the 9.6 µs InterFrameSpacing after the receive carrier is de-asserted. During the first part deferral (InterFrameSpacingPart1 – I FS1) the PCnet-ISA II controller will defer any pending transmit frame and respond to the receive message. The IPG counter will be reset to zero continuously until the carrier de-asserts, at which point the IPG counter will resume the 9.6 µs count once again. Once the IFS1 period of 6.0 µs has elapsed, the PCnet-ISA II controller will begi n timin g the s econ d p ar t defer ral (InterFrameSpacingPart2 – IFS2) of 3.6 µs. Once IFS1 has completed, and IFS2 has commenced, the PCnet-ISA II controller will not defer to a receive packet if a transmit packet is pending. This means that the PCnet-ISA II controller will not attempt to receive the receive packet, since it will start to transmit, and generate a collision at 9.6 µs. The PCnet-ISA II controller will guarantee to complete the preamble (64-bit) and jam (32-bit) sequence before ceasing transmission and invoking the random backoff algorithm. In addition, transmit two part deferral is implemented as an option which can be disabled using the DXMT2PD bit (CSR3). Two-part deferral after transmission is useful for ensuring that severe IPG shrinkage cannot occur in specific circumstances, causing a transmit message to follow a receive message so closely as to make them indistinguishable. During the time period immediately after a transmission has been completed, the external transceiver (in the case of a standard AUI connected device), should generate the SQE Test message (a nominal 10 MHz burst of 5-15 bit times duration) on the CI± pair (within 0.6 µs – 1.6 µs after the transmission ceases). During the time period in which the SQE Test message is expected the PCnet-ISA II controller will not respond to receive carrier sense. See ANSI/IEEE Std 802.3-1990 Edition, 7.2.4.6 (1): “At the conclusion of the output function, the DTE opens a time window during which it expects to see the signal_quality_error signal asserted on the Control In circuit. The time window begins when the CARRIER_STATUS becomes CARRIER_OFF. If execution of the output function does not cause CARRIER_ON to occur, no SQE test occurs in the DTE. The duration of the window shall be at least 4.0 µs but no more than 8.0 µs. During the time window the Carrier Sense Function is inhibited.” The PCnet-ISA II controller implements a carrier sense “blinding” period within 0 – 4.0 µs from de-assertion of carrier sense after transmission. This effectively means that when transmit two par t deferral is enabled (DXMT2PD is cleared) the IFS1 time is from 4 µs to 6 72 Am79C961A µs after a transmission. However, since IPG shrinkage below 4 µs will rarely be encountered on a correctly configured network, and since the fragment size will be larger than the 4 µs blinding window, then the IPG counter will be reset by a worst case IPG shrinkage/ fragment scenario and the PCnet-ISA II controller will defer its transmission. In addition, the PCnet-ISA II controller will not restart the “blinding” period if carrier is detected within the 4.0 µs – 6.0 µs IFS1 period, but will commence timing of the entire IFS1 period. Contention resolution (collision handling) Collision detection is performed and reported to the MAC engine by the integrated Manchester Encoder/ Decoder (MENDEC). If a collision is detected before the complete preamble/ SFD sequence has been transmitted, the MAC Engine will complete the preamble/SFD before appending the jam sequence. If a collision is detected after the preamble/SFD has been completed, but prior to 512 bits being transmitted, the MAC Engine will abort the transmission, and append the jam sequence immediately. The jam sequence is a 32-bit all zeroes pattern. The MAC Engine will attempt to transmit a frame a total of 16 times (initial attempt plus 15 retries) due to normal collisions (those within the slot time). Detection of collision will cause the transmission to be re-scheduled, dependent on the backoff time that the MAC Engine computes. If a single retry was required, the ONE bit will be set in the Transmit Frame Status (TMD1 in the Transmit Descriptor Ring). If more than one retry was required, the MORE bit will be set. If all 16 attempts experienced collisions, the RTRY bit (in TMD3) will be set (ONE and MORE will be clear), and the transmit message will be flushed from the FIFO. If retries have been disabled by setting the DRTY bit in the MODE register (CSR15), the MAC Engine will abandon transmission of the frame on detection of the first collision. In this case, only the RTRY bit will be set and the transmit message will be flushed from the FIFO. If a collision is detected after 512 bit times have been transmitted, the collision is termed a late collision. The MAC Engine will abort the transmission, append the jam sequence, and set the LCOL bit. No retry attempt will be scheduled on detection of a late collision, and the FIFO will be flushed. The IEEE 802.3 Standard requires use of a “truncated binary exponential backoff” algorithm which provides a controlled pseudo-random mechanism to enforce the collision backoff interval, before re-transmission is attempted. See ANSI/IEEE Std 802.3-1990 Edition, 4.2.3.2.5: “At the end of enforcing a collision (jamming), the CSMA/CD sublayer delays before attempting to re-transmit the frame. The delay is an integer multiple of slot Time. The number of slot times to delay before the nth re-transmission attempt is chosen as a uniformly distributed random integer r in the range: 0 ≤ r < 2k, where k = min (n,10).” The PCnet-ISA II controller provides an alternative algorithm, which suspends the counting of the slot time/IPG during the time that receive carrier sense is detected. This algorithm aids in networks where large numbers of nodes are present, and numerous nodes can be in collision. The algorithm effectively accelerates the increase in the backoff time in busy networks, and allows nodes not involved in the collision to access the channel while the colliding nodes await a reduction in channel activity. Once channel activity is reduced, the nodes resolving the collision time out their slot time counters as normal. Manchester Encoder/Decoder (MENDEC) The integrated Manchester Encoder/Decoder provides the PLS (Physical Layer Signaling) functions required for a fully compliant IEEE 802.3 station. The MENDEC provides the encoding function for data to be transmitted on the network using the high accuracy on-board oscillator, driven by either the crystal oscillator or an external CMOS-level compatible clock. The MENDEC also provides the decoding function from data received from the network. The MENDEC contains a Power On Reset (POR) circuit, which ensures that all analog portions of the PCnet-ISA II controller are forced into their correct state during power-up, and prevents erroneous data transmission and/or reception during this time. External Crystal Characteristics When using a crystal to drive the oscillator, the crystal specification shown in the specification table may be used to ensure less than ±0.5 ns jitter at DO±. Am79C961A 73 External Crystal Characteristics Parameter 1. Parallel Resonant Frequency 2. Resonant Frequency Error (CL = 20 pF) 3.Change in Resonant Frequency With Respect To Temperature (0° – 70° C; CL = 20 pF)* 4. Crystal Capacitance 5. Motional Crystal Capacitance (C1) 6. Series Resistance 7. Shunt Capacitance 8. Drive Level 0.022 25 7 –50 Min Nom Max Unit 20 +50 MHz PPM –40 +40 PPM 20 pF pF Ω pF TBD mW Requires trimming crystal spec; no trim is 50 ppm total 74 Am79C961A External Clock Drive Characteristics When driving the oscillator from an external clock source, XTAL2 must be left floating (unconnected). An external clock having the following characteristics must be used to ensure less than ±0.5 ns jitter at DO±. Clock Frequency: Rise/Fall Time (tR/tF): XTAL1 HIGH/LOW Time (tHIGH/tLOW): XTAL1 Falling Edge to Falling Edge Jitter: 20 MHz ±0.01% < 6 ns from 0.5 V to VDD–0.5 40 – 60% duty cycle < ±0.2 ns at 2.5 V input (VDD/2) Receive Path The principal functions of the receiver are to signal the PCnet-ISA II controller that there is information on the receive pair, and to separate the incoming Manchester encoded data stream into clock and NRZ data. The receiver section (see Receiver Block Diagram) consists of two parallel paths. The receive data path is a zero threshold, wide bandwidth line receiver. The carrier path is an offset threshold bandpass detecting line receiver. Both receivers share common bias networks to allow operation over a wide input common mode range. Input Signal Conditioning Transient noise pulses at the input data stream are rejected by the Noise Rejection Filter. Pulse width rejection is proportional to transmit data rate which is fixed at 10 MHz for Ethernet systems but which could be different for proprietary networks. DC inputs more negative than minus 100 mV are also suppressed. The Carrier Detection circuitry detects the presence of an incoming data packet by discerning and rejecting noise from expected Manchester data, and controls the stop and start of the phase-lock loop during clock acquisition. Clock acquisition requires a valid Manchester bit pattern of 1010b to lock onto the incoming message. When input amplitude and pulse width conditions are met at DI±, a clock acquisition cycle is initiated. Clock Acquisition When there is no activity at DI± (receiver is idle), the receive oscillator is phase-locked to STDCLK. The first negative clock transition (bit cell center of first valid Manchester “0") after clock acquisition begins interrupts the receive oscillator. The oscillator is then restarted at the second Manchester “0" (bit time 4) and is phase-locked to it. As a result, the MENDEC acquires the clock from the incoming Manchester bit pattern in 4 bit times with a “1010" Manchester bit pattern. The internal receiver clock, IRXCLK, and the internal received data, IRXDAT, are enabled 1/4 bit time after clock acquisition in bit cell 5. IRXDAT is at a HIGH state when the receiver is idle (no IRXCLK). IRXDAT however, is undefined when clock is acquired and may remain HIGH or change to LOW state whenever IRXCLK is enabled. At 1/4 bit time through bit cell 5, the controller portion of the PCnet-ISA II controller sees the first IRXCLK transition. This also strobes in the incoming fifth bit to the MENDEC as Manchester “1". IRXDAT may make a transition after the IRXCLK rising edge in bit cell 5, but its state is still undefined. The Manchester “1" at bit 5 is clocked to IRXDAT output at 1/4 bit time in bit cell 6. MENDEC Transmit Path The transmit section encodes separate clock and NRZ data input signals into a standard Manchester encoded serial bit stream. The transmit outputs (DO ± ) are designed to operate into terminated transmission lines. When operating into a 78 Ω terminated transmission line, the transmit signaling meets the required output levels and skew for Cheaper net, Ethernet, and IEEE-802.3. Transmitter Timing and Operation A 20 MHz fundamental-mode crystal oscillator provides the basic timing reference for the MENDEC portion of the PCnet-ISA II controller. The crystal input is divided by two to create the internal transmit clock reference. Both clocks are fed into the Manchester Encoder to generate the transitions in the encoded data stream. The internal transmit clock is used by the MENDEC to internally synchronize the Internal Transmit Data (ITXDAT) from the controller and Internal Transmit Enable (ITXEN). The internal transmit clock is also used as a stable bit-rate clock by the receive section of the MENDEC and controller. The oscillator requires an external 0.005% crystal, or an external 0.01% CMOS-level input as a reference. The accuracy requirements, if an external crystal is used, are tighter because allowance for the on-chip oscillator must be made to deliver a final accuracy of 0.01%. Transmission is enabled by the controller. As long as the ITXEN request remains active, the serial output of the controller will be Manchester encoded and appear at DO±. When the internal request is dropped by the controller, the differential transmit outputs go to one of two idle states, dependent on TSEL in the Mode Register (CSR15, bit 9): The idle state of DO± yields “zero” differential to operate transformer-coupled loads In this idle state, DO+ is positive with respect to DO– (logical HIGH). TSEL LOW: TSEL HIGH: Am79C961A 75 PLL Tracking After clock acquisition, the phase-locked clock is compared to the incoming transition at the bit cell center (BCC) and the resulting phase error is applied to a correction circuit. This circuit ensures that the phase-locked clock remains locked on the received signal. Individual bit cell phase corrections of the Voltage Controlled Oscillator (VCO) are limited to 10% of the phase difference between BCC and phaselocked clock. DI ± Data Receiver Manchester Decoder IRXDAT* IRXCLK* Noise Reject Filter Carrier Detect Circuit IRXCRS* *Internal signal 19364B-16 Receiver Block Diagram Carrier Tracking and End of Message The carrier detection circuit monitors the DI± inputs after IRXCRS is asserted for an end of message. IRXCRS de-asserts 1 to 2 bit times after the last positive transition on the incoming message. This initiates the end of reception cycle. The time delay from the last rising edge of the message to IRXCRS deassert allows the last bit to be strobed by IRXCLK and transferred to the controller section, but prevents any extra bit(s) at the end of message. When IRXCRS de-asserts an IRXCRS hold off timer inhibits IRXCRS assertion for at least 2 bit times. Data Decoding The data receiver is a comparator with clocked output to minimize noise sensitivity to the DI± inputs. Input error is less than ±35 mV to minimize sensitivity to input rise and fall time. IRXCLK strobes the data receiver output at 1/4 bit time to determine the value of the Manchester bit, and clocks the data out on IRXDAT on the following IRXCLK. The data receiver also generates the signal used for phase detector comparison to the internal MENDEC voltage controlled oscillator (VCO). Differential Input Terminations The differential input for the Manchester data (DI ±) should be externally terminated by two 40.2 Ω ±1% resistors and one optional common-mode bypass capacitor, as shown in the Differential Input Termination diagram below. The differential input impedance, ZIDF, and the common-mode input impedance, ZICM, 76 are specified so that the Ethernet specification for cable termination impedance is met using standard 1% resistor terminators. If SIP devices are used, 39 Ω is the nearest usable equivalent value. The CI± differential inputs are terminated in exactly the same way as the DI± pair. AUI Isolation Transformer DI+ PCnet-ISA II DI 40.2 Ω 40.2 Ω 0.01 µF to 0.1 µF 19364A-17 Differential Input Termination Collision Detection A MAU detects the collision condition on the network and generates a differential signal at the CI± inputs. This collision signal passes through an input stage which detects signal levels and pulse duration. When the signal is detected by the MENDEC it sets the internal collision signal, ICLSN, HIGH. The condition contin- Am79C961A ues for approximately 1.5 bit times after the last LOW-to-HIGH transition on CI±. Jitter Tolerance Definition The MENDEC utilizes a clock capture circuit to align its internal data strobe with an incoming bit stream. The clock acquisition circuitry requires four valid bits with the values 1010b. Clock is phase-locked to the negative transition at the bit cell center of the second “0" in the pattern. Since data is strobed at 1/4 bit time, Manchester transitions which shift from their nominal placement through 1/4 bit time will result in improperly decoded data. With this as the criteria for an error, a definition of “Jitter Handling” is: The peak deviation approaching or crossing 1/4 bit cell position from nominal input transition, for which the MENDEC section will properly decode data. Attachment Unit Interface (AUI) The AUI is the PLS (Physical Layer Signaling) to PMA (Physical Medium Attachment) interface which connects the DTE to a MAU. The differential interface provided by the PCnet-ISA II controller is fully compliant with Section 7 of ISO 8802-3 (ANSI/IEEE 802.3). After the PCnet-ISA II controller initiates a transmission, it will expect to see data “looped-back” on the DI± pair (when the AUI port is selected). This will internally generate a “carrier sense”, indicating that the integrity of the data path to and from the MAU is intact, and that the MAU is operating correctly. This “carrier sense” signal must be asserted within sometime before end of transmission. If “carrier sense” does not become active in response to the data transmission, or becomes inactive before the end of transmission, the loss of carrier (LCAR) error bit will be set in the Transmit Descriptor Ring (TMD3, bit 11) after the packet has been transmitted. Twisted Pair Transmit Function The differential driver circuitry in the TXD± and TXP± pins provides the necessary electrical driving capability and the pre-distortion control for transmitting signals over maximum length Twisted Pair cable, as specified by the 10BASE-T supplement to the IEEE 802.3 Standard. The transmit function for data output meets the propagation delays and jitter specified by the standard. Twisted Pair Receive Function The receiver complies with the receiver specifications of the IEEE 802.3 10BASE-T Standard, including noise immunity and received signal rejection criteria (‘Smart Squelch’). Signals meeting these criteria appearing at the RXD ± d ifferential input pair are routed to the MENDEC. The receiver function meets the propagation delays and jitter requirements specified by the standard. The receiver squelch level drops to half its threshold value after unsquelch to allow reception of minimum amplitude signals and to offset carrier fade in the event of worst case signal attenuation conditions. Note that the 10BASE-T Standard defines the receive input amplitude at the external Media Dependent Interface (MDI). Filter and transformer loss are not specified. The T-MAU receiver squelch levels are designed to account for a 1 dB insertion loss at 10 MHz for the type of receive filters and transformers usually used. Normal 10BASE-T compatible receive thresholds are invoked when the LRT bit (CSR15, bit 9) is LOW. When the LRT bit is set, the Low Receive Threshold option is invoked, and the sensitivity of the T-MAU receiver is increased. Increasing T-MAU sensitivity allows the use of lines longer than the 100 m target distance of standard 10BASE-T (assuming typical 24 AWG cable). Increased receiver sensitivity compensates for the increased signal attenuation caused by the additional cable distance. However, making the receiver more sensitive means that it is also more susceptible to extraneous noise, primarily caused by coupling from co-resident services (crosstalk). For this reason, end users may wish to invoke the Low Receive Threshold option on 4-pair cable only. Multi-pair cables within the same outer sheath have lower crosstalk attenuation, and may allow noise emitted from adjacent pairs to couple into the receive pair, and be of sufficient amplitude to falsely unsquelch the T-MAU. Link Test Function The link test function is implemented as specified by 10BASE-T standard. During periods of transmit pair inactivity,’Link beat pulses’ will be periodically sent over the twisted pair medium to constantly monitor medium integrity. Twisted Pair Transceiver (T-MAU) This section describes operation of the T-MAU when operating in the Half Duplex mode. When in Half Duplex mode, the T-MAU implements the Medium Attachment Unit (MAU) functions for the Twisted Pair Medium as specified by the supplement to IEEE 802.3 standard (Type 10BASE-T). When operating in Full Duplex mode, the MAC engine behavior changes as described in the Full Duplex Operation section. The T-MAU provides twisted pair driver and receiver circuits, including on-board transmit digital predistortion and receiver squelch, and a number of additional features including Link Status indication, Automatic Twisted Pair Receive Polarity Detection/Correction and Indication, Receive Carrier Sense, Transmit Active and Collision Present indication. Am79C961A 77 When the link test function is enabled (DLNKTST bit in CSR15 is cleared), the absence of link beat pulses and receive data on the RXD± pair will cause the TMAU to go into the Link Fail state. In the Link Fail state, data transmission, data reception, data loopback and the collision detection functions are disabled and remain disabled until valid data or greater than 5 consecutive link pulses appear on the RXD± pair. During Link Fail, the Link Status (LNKST indicated by LED0) signal is inactive. When the link is identified as functional, the LNKST signal is asserted, and LED0 o utput will be activated. Upon power up or assertion of the RESET pin, the T-MAU will be forced into the Link Fail state. Reading the RESET register of the PCnet-ISA+ (software RESET) has no effect on the T-MAU In order to inter-operate with systems which do not implement Link Test, this function can be disabled by setting the DLNKTST bit. With Link Test disabled, the Data Driver, Receiver and Loopback functions as well as Collision Detection remain enabled irrespective of the presence or absence of data or link pulses on the RXD± pair. Link Test pulses continue to be sent regardless of the state of the DLNKTST bit. Polarity Detection and Reversal The T-MAU receive function includes the ability to invert the polarity of the signals appearing at the RXD± pair if the polarity of the received signal is reversed (such as in the case of a wiring error). This feature allows data packets received from a reverse wired RXD± input pair to be corrected in the T-MAU prior to transfer to the MENDEC. The polarity detection function is activated following reset or Link Fail, and will reverse the receive polarity based on both the polarity of any previous link beat pulses and the polarity of subsequent packets with a valid End Transmit Delimiter (ETD). When in the Link Fail state, the T-MAU will recognize link beat pulses of either positive or negative polarity. Exit from the Link Fail state occurs at the reception of 5 – 6 consecutive link beat pulses of identical polarity. On entry to the Link Pass state, the polarity of the last 5 link beat pulses is used to determine the initial receive polarity configuration and the receiver is reconfigured to subsequently recognize only link beat pulses of the previously recognized polarity. Positive link beat pulses are defined as transmitted signal with a positive amplitude greater than 585 mV with a pulse width of 60 ns – 200 ns. This positive excursion may be followed by a negative excursion. This definition is consistent with the expected received signal at a correctly wired receiver, when a link beat pulse, which fits the template of Figure 14-12 of the 10BASE-T Standard, is generated at a transmitter and passed through 100 m of twisted pair cable. Negative link beat pulses are defined as transmitted signals with a negative amplitude greater than 585 mV with a pulse width of 60 ns – 200 ns. This negative excursion may be followed by a positive excursion. This definition is consistent with the expected received signal at a reverse wired receiver, when a link beat pulse which fits the template of Figure 14-12 in the 10BASE-T Standard is generated at a transmitter and passed through 100 m of twisted pair cable. The polarity detection/correction algorithm will remain “armed” until two consecutive packets with valid ETD of identical polarity are detected. When “ armed, ” t he receiver is capable of changing the initial or previous polarity configuration according to the detected ETD polarity. On receipt of the first packet with valid ETD following reset or link fail, the T-MAU will use the inferred polarity information to configure its RXD± input, regardless of its previous state. On receipt of a second packet with a valid ETD with correct polarity, the detection/correction algorithm will “lock-in” the received polarity. If the second (or subsequent) packet is not detected as confirming the previous polarity decision, the most recently detected ETD polarity will be used as the default. Note that packets with invalid ETD have no effect on updating the previous polarity decision. Once two consecutive packets with valid ETD have been received, the T-MAU will lock the correction algorithm until either a Link Fail condition occurs or RESET is asserted. During polarity reversal, an internal POL signal will be active. During normal polarity conditions, this internal POL signal is inactive. The state of this signal can be read by software and/or displayed by LED when enabled by the LED control bits in the ISA Bus Configuration Registers (ISACSR5, 6, 7). Twisted Pair Interface Status Three internal signals (XMT, RCV and COL) indicate whether the T-MAU is transmitting, receiving, or in a collision state. These signals are internal signals and the behavior of the LED outputs depends on how the LED output circuitry is programmed. The T-MAU will power up in the Link Fail state and the normal algorithm will apply to allow it to enter the Link Pass state. In the Link Pass state, transmit or receive activity will be indicated by assertion of RCV signal going active. If T-MAU is selected using the PORTSEL bits in CSR15, when moving from AUI to T-MAU selection, the T-MAU will be forced into the Link Fail state. In the Link Fail state, XMT, RCV and COL are inactive. Collision Detect Function Activity on both twisted pair signals RXD± and TXD± constitutes a collision, thereby causing the COL signal to be asserted. (COL is used by the LED control circuits) COL will remain asserted until one of the two col- 78 Am79C961A liding signals changes from active to idle. COL stays active for 2 bit times at the end of a collision. Signal Quality Error (SQE) Test (Heartbeat) Function The SQE function is disabled when the 10BASE-T port is selected and in Link Fail state. Jabber Function The Jabber function inhibits the twisted pair transmit function of the T-MAU if the TXD± circuit is active for an excessive period (20 ms–150 ms). This prevents any one node from disrupting the network due to a ‘stuck-on’ or faulty transmitter. If this maximum transmit time is exceeded, the T-MAU transmitter circuitry is disabled, the JAB bit is set (CSR4, bit 1), and the COL signal asserted. Once the transmit data stream to the T-MAU is removed, an “unjab” time of 250 ms – 750 ms will elapse before the T-MAU deasserts COL and re-enables the transmit circuitry. Power Down The T-MAU circuitry can be made to go into low power mode. This feature is useful in battery powered or low duty cycle systems. The T-MAU will go into power down mode when RESET is active, coma mode is active, or the T-MAU is not selected. Refer to the Power Down Mode section for a description of the various power down modes. Any of the three conditions listed above resets the internal logic of the T-MAU and places the device into power down mode. In this mode, the Twisted Pair driver pins (TXD±,TXP±) are asserted LOW, and the internal T-MAU status signals (LNKST, RCVPOL, XMT, RCV and COLLISION) are inactive. Once the SLEEP pin is deasserted, the T-MAU will be forced into the Link Fail state. The T-MAU will move to the Link Pass state only after 5–6 link beat pulses and/ or a single received message is detected on the RXD± pair. In S nooze m ode, the T-MAU receive circuitry will remain enabled even while the SLEEP pin is driven LOW. The T-MAU circuitry will always go into power down mode if RESET is asserted, coma is enabled, or the T-MAU is not selected. erating in the Full Duplex mode, the following changes to device operation are made: Bus Interface/Buffer Management Unit changes: 1. The first 64 bytes of every transmit frame are not preserved in the transmit FIFO during transmission of the first 512 bits transmitted on the network, as described in the Transmit Exception Conditions section. Instead, when Full Duplex mode is active and a frame is being transmitted, the XMTFW bits (CSR80, bits 9, 8) always govern when transmit DMA is requested. 2. Successful reception of the first 64 bytes of every receive frame is not a requirement for Receive DMA to begin as described in the Receive Exception Conditions section. Instead, receive DMA will be requested as soon as either the RCVFW threshold (CSR80 bits 12, 13) is reached or a complete valid receive frame is in the Receive FIFO, regardless of length. This receive FIFO operation is identical to when the RPA bit (CSR124, bit 3) is set during Half Duplex mode operation. MAC Engine changes: 1. Changes to the Transmit Deferral mechanism: A. Transmission is not deferred while receive is active. B. The Inter Packet Gap (IPG) counter which governs transmit deferral during the IPG between back-to-back transmits is started when transmit activity for the first packet ends instead of when transmit and carrier activity ends. 2. When the AUI or GPSI port is active, Loss of Carrier (LCAR) reporting is disabled (LCAR is still reported when the 10BASE-T port is active if a packet is transmitted while in the Link Fail state). 3. The 4.0 µs carrier sense blinding period after a transmission during which the SQE test normally occurs is disabled. 4. When the AUI or GPSI port is active, the SQE Test error (Collision Error, CERR) reporting is disabled (CERR is still reported when the 10BASE-T port is active if a packet is transmitted while in the Link Fail state). 5. The collision indication input to the MAC Engine is ignored. T-MAU changes: 1. The transmit to receive loopback path in the T-MAU is disabled. 2. The collision detect circuit is disabled. 3. The “heartbeat” generation (SQE Test function) is disabled. Full Duplex Operation The PCnet-ISA II supports Full Duplex operation on the 10BASE-T, AUI, and GPSI ports. Full Duplex operation allows simultaneous transmit and receive activity on the TXD± and RXD± pairs of the 10BASE-T port, the DO± and DI± pairs of the AUI port, and the TXDAT and RXDAT pins of the GPSI port. It is enabled by the FDEN and AUIFD bits located in ISACSR9. When op- Am79C961A 79 EADI (External Address Detection Interface) This interface is provided to allow external address filtering. It is selected by setting the EADISEL bit in ISACSR2. This feature is typically utilized for terminal servers, bridges and/or router type products. The use of external logic is required to capture the serial bit stream from the PCnet-ISA II controller, compare it with a table of stored addresses or identifiers, and perform the desired function. The EADI interface operates directly from the NRZ decoded data and clock recovered by the Manchester decoder or input to the GPSI, allowing the external address detection to be performed in parallel with frame reception and address comparison in the MAC Station Address Detection (SAD) block. SRDCLK is provided to allow clocking of the receive bit stream into the external address detection logic. SRDCLK runs only during frame reception activity. Once a received frame commences and data and clock are available, the EADI logic will monitor the alternating (“1,0") preamble pattern until the two ones of the Start Frame Delimiter (“1,0,1,0,1,0,1,1") are detected, at which point the SF/BD output will be driven HIGH. After SF/BD is asserted the serial data from SRD should be de-serialized and sent to a content addressable memory (CAM) or other address detection device. To allow simple serial to parallel conversion, SF/BD is provided as a strobe and/or marker to indicate the delineation of bytes, subsequent to the SFD. This provides a mechanism to allow not only capture and/or decoding of the physical or logical (group) address, it also facilitates the capture of header information to determine protocol and or inter-networking information. The EAR pin is driven LOW by the external address comparison logic to reject the frame. If an internal address match is detected by comparison with either the Physical or Logical Address field, the frame will be accepted regardless of the condition of EAR. Incoming frames which do not pass the internal address comparison will continue to be received. This allows approximately 58 byte times after the last destination address bit is available to generate the EAR signal, assuming the device is not configured to accept runt packets. EAR will be ignored after 64 byte times after the SFD, and the frame will be accepted if EAR has not been asserted before this time. If Runt Packet Accept is configured, the EAR s ignal must be generated prior to the receive message completion, which could be as short as 12 byte times (assuming 6 bytes for source address, 2 bytes for length, no data, 4 bytes for FCS) after the last bit of the destination address is available. EAR must have a pulse width of at least 200 ns. Note that setting the PROM bit (CSR15, bit 15) will cause all receive frames to be received, regardless of the state of the EAR input. If the DRCUPA bit (CSR15.B) is set and the logical address (LADRF) is set to zero, only frames which are not rejected by EAR will be received. The EADI interface will operate as long as the STRT bit in CSR0 is set, even if the receiver and/or transmitter are disabled by software (DTX and DRX bits in CSR15 set). This situation is useful as a power down mode in that the PCnet-ISA II controller will not perform any DMA operations; this saves power by not utilizing the ISA bus driver circuits. However, external circuitry could still respond to specific frames on the network to facilitate remote node control. The table below summarizes the operation of the EADI features. Internal/External Address Recognition Capabilities PROM 1 0 0 EAR X 1 0 Required Timing No timing requirements No timing requirements Low for 200 ns within 512 bits after SFD Received Messages All Received Frames All Received Frames Physical/Logical Matches General Purpose Serial Interface (GPSI) The PCnet-ISA II controller contains a General Purpose Serial Interface (GPSI) designed for testing the digital portions of the chip. The MENDEC, AUI, and twisted pair interface are by-passed once the device is set up in the special “test mode” for accessing the GPSI functions. Although this access is intended only for testing the device, some users may find the non-enc od e d d at a fu n c ti o n s u s ef u l i n s o me s p e c i al applications. Note, however, that the GPSI functions can be accessed only when the PCnet-ISA II devices operate as a bus master. The PCnet-ISA II GPSI signals are consistent with the LANCE digital serial interface. Since the GPSI functions can be accessed only through a special test mode, expect some loss of functionality to the device when the GPSI is invoked. The AUI and 10BASE-T analog interfaces are disabled along with the internal 80 Am79C961A MENDEC logic. The LA (unlatched address) pins are removed and become the GPSI signals, therefore, only 20 bits of address space is available. The table below shows the GPSI pin configuration: To invoke the GPSI signals, follow the procedure below: 1. After reset or I/O read of Reset Address, write 10b to PORTSEL bits in CSR15. 2. Set the ENTST bit in CSR4 3. Set the GPSIEN bit in CSR124 (see note below) (The pins LA17–LA23 will change function after the completion of the above three steps.) 4. Clear the ENTST bit in CSR4 5. Clear Media Select bits in ISACSR2 6. Define the PORTSEL bits in the MODE register (CSR15) to be 10b to define GPSI port. The MODE register image is in the initialization block. Note: LA pins will be tristated before writing to GPSIEN bit. After writing to GPSIEN, LA[17–21] will be inputs, LA[22–23] will be outputs. GPSI Pin Configurations GPSI Function Receive Data Receive Clock Receive Carrier Sense Collision Transmit Clock Transmit Enable Transmit Data GPSI I/O Type I I I I I O O LANCE GPSI Pin RX RCLK RENA CLSN TCLK TENA TX PCnet-ISA II GPSI Pin RXDAT SRDCLK RXCRS CLSN STDCLK TXEN TXDAT PCnet-ISA II Pin Number 5 6 7 9 10 11 12 PCnet-ISA II Normal Pin Function LA17 LA18 LA19 LA20 LA21 LA22 LA23 Note: The GPSI Function is available only in the Bus Master Mode of operation. Am79C961A 81 IEEE 1149.1 Test Access Port Interface An IEEE 1149.1 compatible boundary scan Test Access Port is provided for board-level continuity test and diagnostics. All digital input, output, and input/output pins are tested. Analog pins, including the AUI differential driver (DO±) and receivers (DI±, CI±), and the crystal input (XTAL1/XTAL2) pins, are tested. The T-MAU drivers TXD±, TXP±, and receiver RXD± are also tested. The following is a brief summary of the IEEE 1149.1 compatible test functions implemented in the PCnet-ISA II controller. Boundary Scan Circuit The boundary scan test circuit requires four extra pins (TCK, TMS, TDI and TDO), defined as the Test Access Port (TAP). It includes a finite state machine (FSM), an instruction register, a data register array, and a power-on reset circuit. Internal pull-up resistors are provided for the TDI, TCK, and TMS pins. The TCK pin must not be left unconnected. The boundary scan circuit remains active during sleep. TAP FSM The TAP engine is a 16-state FSM, driven by the Test Clock (TCK) and the Test Mode Select (TMS) pins. This FSM is in its reset state at power-up or RESET. An independent power-on reset circuit is provided to ensure the FSM is in the TEST_LOGIC_RESET state at power-up. Supported Instructions In addition to the minimum IEEE 1149.1 requirements (BYPASS, EXTEST and SAMPLE instructions), three additional instructions (IDCODE, TRIBYP and SETBYP) are provided to further ease board-level testing. All unused instruction codes are reserved. See the table below for a summary of supported instructions. Instruction Register and Decoding Logic After hardware or software RESET, the IDCODE instruction is always invoked. The decoding logic gives signals to control the data flow in the DATA registers according to the current instruction. Boundary Scan Register (BSR) Each BSR cell has two stages. A flip-flop and a latch are used in the SERIAL SHIFT STAGE and the PARALLEL OUTPUT STAGE, respectively. There are four possible operational modes in the BSR cell: 1 2 3 4 Capture Shift Update System Function Other Data Registers (1) BYPASS REG (1 BIT) (2) DEV ID REG (32 bits) Bits 31–28: Bits 27–12: Bits 11–1: Version Part number (2261h) Manufacturer ID. The 11 bit manufacturer ID code for AMD is 00000000001 according to JEDEC Publication 106-A. Always a logic 1 Bit 0: IEEE 1149.1 Supported Instruction Summary Instruction Name EXTEST IDCODE SAMPLE TRIBYP SETBYP BYPASS Selected Data Reg BSR ID REG BSR Bypass Bypass Bypass Instruction Code 0000 0001 0010 0011 0100 1111 Description External Test ID Code Inspection Sample Boundary Force Tristate Control Boundary to 1/0 Bypass Scan Mode Test Normal Normal Normal Test Normal Power Saving Modes The PCnet-ISA II controller supports two hardware power-savings modes. Both are entered by asserting the SLEEP pin LOW. In coma mode, the PCnet-ISA II controller will go into deep sleep with no support to automatically wake itself up. Sleep mode is enabled when the AWAKE bit in ISACSR2 is reset. This mode is the default powerdown mode. In Snooze mode, enabled by setting the AWAKE bit in ISACSR2 and driving the SLEEP pin LOW, the T-MAU receive circuitry will remain enabled even while the SLEEP pin is driven LOW. The LED0 output will also continue to function, indicating a good 10BASE-T link if 82 Am79C961A there are link beat pulses or valid frames present. This LED0 pin can be used to drive a LED and/or external hardware that directly controls the SLEEP pin of the PCnet-ISA II controller. This configuration effectively wakes the system when there is any activity on the 10BASE-T link. IEEE Address Access The address PROM may be an external memory device that contains the node’s unique physical Ethernet address and any other data stored by the board manufacturer. The software accesses must be 16-bit. This information may be stored in the EEPROM. Boot PROM Access The boot PROM is an external memory resource located by the address selected by the EEPROM or the BPAM i nput in s lave m ode. It may be software accessed as an 8-bit or 16-bit resource but the latter is recommended for best performance. Static RAM Access The static RAM is only present in the Bus Slave mode. In the Bus Slave mode, two SRAM access schemes are available. When the Shared Memory architecture mode is selected, the SRAM is accessed using ISA memory cycles to the address range selected by the SMAM input. It may be accessed as an 8 or 16-bit resource but the latter is recommended for best performance. When the Programmed I/O architecture mode is selected, the SRAM is accessed through ISACSR0 and ISACSR1 using the RAP and IDP. Access Operations (Software) We begin by describing how byte and word data are addressed on the ISA bus, including conversion cycles where 16-bit accesses are turned into 8-bit accesses because the resource accessed did not support 16-bit operations. Then we describe how registers and other resources are accessed. This section is for the device programmer, while the next section (bus cycles) is for the hardware designer. I/O Resources The PCnet-ISA II controller has both I/O and memory resources. In the I/O space the resources are organized as indicated in the following table: Offset 0h 10h 12h 14h 16h #Bytes 16 2 2 2 2 Register IEEE Address RDP RAP(shared by RDP and IDP) Reset IDP Bus Cycles (Hardware) The PCnet-ISA II controller supports both 8-bit and 16-bit hardware bus cycles. The following sections outline where any limitations apply based upon the architecture mode and/or the resource that is being accessed (PCnet-ISA II controller registers, address PROM, boot PROM, or shared memory SRAM). For completeness, the following sections are arranged by architecture (Bus Master Mode or Bus Slave Mode). SRAM resources apply only to Bus Slave Mode. All resources (registers, PROMs, SRAM) are presented to the ISA bus by the PCnet-ISA II controller. With few exceptions, these resources can be configured for either 8-bit or 16-bit bus cycles. The I/O resources (registers, address PROM) are width configured using the EEPROM. The memory resources (boot PROM, SRAM) are width configured by external hardware. For 16-bit memory accesses, hardware external to the PCnet-ISA II controller asserts MEMCS16 when either of the two memory resources is selected. The ISA bus requires that all memory resources within a block of 128 Kbytes be the same width, either 8- or 16-bits. The reason for this is that the MEMCS16 signal is generally a decode of the LA17-23 address lines. 16-bit memory capability is desirable since two 8-bit accesses take the same amount of time as four 16-bit accesses. All accesses to 8-bit resources (which do not return MEMCS16 or IOCS16) use SD0-7. If an odd byte is accessed, the Current Master swap buffer turns on. The PCnet-ISA II controller does not respond to any addresses outside of the offset range 0-17h. I/O offsets 18h and up are not used by the PCnet-ISA II controller. I/O Register Access The register address port (RAP) is shared by the register data port (RDP) and the ISACSR data port (IDP) to save registers. To access the Ethernet controller’s RDP or IDP, the RAP should be written first, followed by the read or write access to the RDP or IDP. I/O register accesses should be coded as 16-bit accesses, even if the PCnet-ISA II controller is hardware configured for 8-bit I/O bus cycles. It is acceptable (and transparent) for the motherboard to turn a 16-bit software access into two separate 8-bit hardware bus cycles. The motherboard accesses the low byte before the high byte and the PCnet-ISA II controller has circuitry to specifically support this type of access. The reset register causes a reset when read. Any value will be accepted and the cycle may be 8 or 16 bits wide. Writes are ignored. All PCnet-ISA II controller register accesses should be coded as 16-bit operations. “Note that the RAP is cleared on Reset.” Am79C961A 83 During an odd byte read the swap buffer copies the data from SD0-7 to the high byte. During an odd byte write the Current Master swap buffer copies the data from the high byte to SD0-7. The PCnet-ISA II controller can be configured to be an 8-bit I/O resource even in a 16-bit system; this is set by the EEPROM. It is recommended that the PCnet-ISA II controller be configured for 8-bit only I/O bus cycles for maximum compatibility with PC/AT clone motherboards. When the PCnet-ISA II controller is in an 8-bit system such as a PC/XT, SBHE a nd IOCS16 must be left unconnected (these signals do not exist in the PC/XT). This will force ALL resources (I/O and memory) to support only 8-bit bus cycles. The PCnet-ISA II controller will function in an 8-bit system only if configured for Bus Slave Mode. Accesses to 16-bit resources (which do retur n MEMCS16 or IOCS16) use either or both SD0–7 and SD8 – 15. A word access is indicated by A0=0 and SBHE=0 and data is transferred on all 16 data lines. An even byte access is indicated by A0=0 and SBHE=1 and data is transferred on SD0–7. An odd-byte access is indicated by A0=1 and SBHE=0 and data is transferred on SD8-15. It is illegal to have A0=1 and SBHE=1 in any bus cycle. The PCnet-ISA II controller returns only IOCS16; MEMCS16 must be generated by external hardware if desired. The use of MEMCS16 applies only to Shared Memory Mode. The following table describes all possible types of ISA bus accesses, including Permanent Master as Current Master and PCnet-ISA II controller as Current Master. The PCnet-ISA II controller will not work with 8-bit memory while it is Current Master. Any descriptions of 8-bit memory accesses are for when the Permanent Master is Current Master. The two byte columns (D0 – 7 and D8 – 15) indicate whether the bus master or slave is driving the byte. CS16 is a shorthand for MEMCS16 and IOCS16. Bus Master Mode The PCnet-ISA II controller can be configured as a Bus Master only in systems that support bus mastering. In addition, the system is assumed to support 16-bit memory (DMA) cycles (the PCnet-ISA II controller does not use the MEMCS16 signal on the ISA bus). This does not preclude the PCnet-ISA II controller from doing 8-bit I/O transfers. The PCnet-ISA II controller will not function as a bus master in 8-bit platforms such as the PC/XT. Refresh Cycles Although the PCnet-ISA II controller is neither an originator or a receiver of refresh cycles, it does need to avoid unintentional activity during a refresh cycle in bus master mode. A refresh cycle is performed as follows: First, the REF signal goes active. Then a valid refresh address is placed on the address bus. MEMR goes active, the refresh is performed, and MEMR goes inactive. The refresh address is held for a short time and them goes invalid. Finally, REF goes inactive. During a refresh cycle, as indicated by REF being active, the PCnet-ISA II controller ignores DACK if it goes active until it goes inactive. It is necessary to ignore DACK during a refresh because some motherboards generate a false DACK at that time. ISA Bus Accesses R/W RD RD RD RD RD WR WR WR WR WR A0 0 1 0 1 0 0 1 0 1 0 SBHE 1 0 0 0 0 1 0 0 0 0 CS16 x 1 1 0 0 x 1 1 0 0 D0–7 Slave Slave Slave Float Slave Master Master Master Float Master D8–15 Float Float Float Slave Slave Float Float Master Master Master Comments Low byte RD High byte RD with swap 16-Bit RD converted to low byte RD High byte RD 16-Bit RD Low byte WR High byte WR with swap 16-Bit WR converted to low byte WR High byte WR 16-Bit WR Address PROM Cycles External PROM The Address PROM is a small (16 bytes) 8-bit PROM connected to the PCnet-ISA II controller Private Data Bus. The PCnet-ISA II controller will support only 8-bit ISA I/O bus cycles for the address PROM; this limitation is transparent to software and does not preclude 16-bit software I/O accesses. An access cycle begins 84 Am79C961A with the Permanent Master driving AEN LOW, driving the addressess valid, and driving IOR active. The PCnet-ISA II controller detects this combination of signals and arbitrates for the Private Data Bus (PRDB) if necessary. IOCHRDY is driven LOW during accesses to the address PROM. When the Private Data Bus becomes available, the PCnet-ISA II controller drives APCS active, releases IOCHRDY, turns on the data path from PRD0-7, and enables the SD0-7 drivers (but not SD8-15). During this bus cycle, IOCS16 is not driven active. This condition is maintained until IOR goes inactive, at which time the bus cycle ends. Data is removed from SD0-7 within 30 ns. Address PROM Cycles Using EEPROM Data Default mode. In this mode, the IEEE address information is stored not in an external parallel PROM but in the EEPROM along with other configuration information. PCnet-ISA II will respond to I/O reads from the IEEE address (the first 16 bytes of the I/O map) by supplying data from an internal RAM inside PCnet-ISA II. This internal RAM is loaded with the IEEE address at RESET and is write protected. Ethernet Controller Register Cycles Ethernet controller registers (RAP, RDP, IDP) are naturally 16-bit resources but can be configured to operate with 8-bit bus cycles provided the proper protocol is followed. This means on a read, the PCnet-ISA II controller will only drive the low byte of the system data bus; if an odd byte is accessed, it will be swapped down. The high byte of the system data bus is never driven by the PCnet-ISA II controller under these conditions. On a write cycle, the even byte is placed in a holding register. An odd byte write is internally swapped up and augmented with the even byte in the holding register to provide an internal 16-bit write. This allows the use of 8-bit I/O bus cycles which are more likely to be compatible with all ISA-compatible clones, but requires that both bytes be written in immediate succession. This is accomplished simply by treating the PCnet-ISA II controller registers as 16-bit software resources. The motherboard will convert the 16-bit accesses done by software into two sequential 8-bit accesses, an even byte access followed immediately by an odd byte access. An access cycle begins with the Permanent Master driving AEN LOW, driving the address valid, and driving IOR or IOW active. The PCnet-ISA II controller detects this combination of signals and drives IOCHRDY LOW. IOCS16 will also be driven LOW if 16-bit I/O bus cycles are enabled. When the register data is ready, IOCHRDY will be released HIGH. This condition is maintained until IOR or IOW goes inactive, at which time the bus cycle ends. RESET Cycles A read to the reset address causes an PCnet-ISA II controller reset. This has the same effect as asserting the RESET pin on the PCnet-ISA+ controller (which happens on system power up or on a hard boot) except that the T-MAU is NOT reset. The T-MAU will retain its link pass/fail state, disregarding the software RESET command. The subsequent write cycle needed in the NE2100 LANCE based family of Ethernet cards is not required but does not have any harmful effects. IOCS16 is not asserted in this cycle. ISA Configuration Register Cycles The ISA configuration registers are accessed by placing the address of the desired register into the RAP and reading the IDP. The ISACSR bus cycles are identical to all other PCnet-ISA II controller register bus cycles. Boot PROM Cycles The Boot PROM is an 8-bit PROM connected to the PCnet-ISA II controller Private Data Bus (PRDB) and can occupy up to 64K of address space. Since the PCnet-ISA II controller does not generate MEMCS16, only 8-bit ISA memory bus cycles to the boot PROM are supported in Bus Master Mode; this limitation is transparent to software and does not preclude 16-bit software memory accesses. A boot PROM access cycle begins with the Per manent Master driving the addresses valid, REF inactive, and MEMR active. (AEN is not involved in memory cycles). The PCnet-ISA II controller detects this combination of signals, drives IOCHRDY LOW, and reads a byte out of the Boot PROM. The data byte read is driven onto the lower system data bus lines and IOCHRDY is released. This condition is maintained until MEMR goes inactive, at which time the access cycle ends. The BPCS signal generated by the PCnet-ISA II controller is three 20 MHz clock cycles wide (300 ns). Including delays, the Boot PROM has 275 ns to respond to the BPCS signal from the PCnet-ISA II controller. This signal is intended to be connected to the CS pin on the boot PROM, with the PROM OE pin tied to ground. Current Master Operation Current Master operation only occurs in the Bus Master mode. It does not occur in the Bus Slave mode. There are three phases to the use of the bus by the PCnet-ISA II controller as Current Master, the Obtain Phase, the Access Phase, and the Release Phase. Obtain Phase A Master Mode Transfer Cycle begins by asserting DRQ. When the Permanent Master asserts DACK, the PCnet-ISA II controller asserts MASTER, signifying it has taken control of the ISA bus. The Permanent Master tristates the address, command, and data lines Am79C961A 85 within 60 ns of DACK g oing active. The Permanent Master drives AEN inactive within 71 ns of MASTER going active. Access Phase The ISA bus requires a wait of at least 125 ns after MASTER is asserted before the new master is allowed to drive the address, command, and data lines. The PCnet-ISA II controller will actually wait 3 clock cycles or 150 ns. The following signals are not driven by the Permanent Master and are simply pulled HIGH: BALE, IOCHRDY, IOCS16, MEMCS16, SRDY. Therefore, the PCnet-ISA II controller assumes the memory which it is accessing is 16 bits wide and can complete an access in the time programmed for the PCnet-ISA II controller MEMR and MEMW s ignals. Refer to the ISA Bus Configuration Register description section. Release Phase When the PCnet-ISA II controller is finished with the bus, it drives the command lines inactive. 50 ns later, the controller tri-states the command, address, and data lines and drives DRQ inactive. 50 ns later, the controller drives MASTER inactive. The Permanent Master drives AEN active within 71 ns of MASTER going inactive. The Permanent Master is allowed to drive the command lines no sooner than 60 ns after DACK goes inactive. Master Mode Memory Read Cycle After the PCnet-ISA II controller has acquired the ISA bus, it can perform a memory read cycle. All timing is generated relative to the 20 MHz clock (network clock). Since there is no way to tell if memory is 8-bit or 16-bit or when it is ready, the PCnet-ISA II controller by default assumes 16-bit, 1 wait state memory. The wait state assumption is based on the default value in the MSRDA register in ISACSR0. The cycle begins with SA0-19, SBHE, and LA17-23 being presented. The ISA bus requires them to be valid for at least 28 ns before a read command and the PCnet-ISA II controller provides one clock or 50 ns of setup time before asserting MEMR. The ISA bus requires MEMR to be active for at least 219 ns, and the PCnet-ISA II controller provides a default of 5 clocks, or 250 ns, but this can be tuned for faster systems with the Master Mode Read Active (MSRDA) register (see section 2.5.2). Also, if IOCHRDY is driven LOW, the PCnet-ISA II controller will wait. The wait state counter must expire and IOCHRDY must be HIGH for the PCnet-ISA II controller to continue. The PCnet-ISA II controller then accepts the memory read data. The ISA bus requires all command lines to remain inactive for at least 97 ns before starting another bus cycle and the PCnet-ISA II controller provides at least two clocks or 100 ns of inactive time. The ISA bus requires read data to be valid no more than 173 ns after receiving MEMR active and the PCnet-ISA II controller requires 10 ns of data setup time. The ISA bus requires read data to provide at least 0 ns of hold time and to be removed from the bus within 30 ns after MEMR goes inactive. The PCnet-ISA II controller requires 0 ns of data hold time. Master Mode Memory Write Cycle After the PCnet-ISA II controller has acquired the ISA bus, it can perform a memory write cycle. All timing is generated relative to a 20 MHz clock which happens to be the same as the network clock. Since there is no way to tell if memory is 8- or 16-bit or when it is ready, the PCnet-ISA II controller by default assumes 16-bit, 1 wait state memory. The wait state assumption is based on the default value in the MSWRA register in ISACSR1. The cycle begins with SA0-19, SBHE, and LA17-23 being presented. The ISA bus requires them to be valid at least 28 ns before MEMW goes active and data to be valid at least 22 ns before MEMW goes active. The PCnet-ISA II controller provides one clock or 50 ns of setup time for all these signals. The ISA bus requires MEMW to be active for at least 219 ns, and the PCnet-ISA II controller provides a default of 5 clocks, or 250 ns, but this can be tuned for faster systems with the Master Mode Write Active (MSWRA) register (ISACSR1). Also, if IOCHRDY is driven LOW, the PCnet-ISA II controller will wait. IOCHRDY must be HIGH for the PCnet-ISA II controller to continue. The ISA bus requires data to be valid for at least 25 ns after MEMW goes inactive, and the PCnet-ISA II controller provides one clock or 50 ns. The ISA bus requires all command lines to remain inactive for at least 97 ns before starting another bus cycle. The PCnet-ISA II controller provides at least two clocks or 100 ns of inactive time when bit 4 in ISACSR2 is set. The EISA bus requires all command lines to remain inactive for at least 170 ns before starting another bus cycle. When bit 4 in ISACSR4 is cleared, the PCnet-ISA II controller provides 200 ns of inactive time. Back-to-Back DMA Requests The PCnet-ISA II provides for fair bus bandwidth sharing between two bus mastering devices on the ISA bus through an adaptive delay which is inserted between back-to-back DMA requests. When the PCnet-ISA II requires bus access immediately following a bus ownership period, it first checks the status of the three currently unused DRQ pins. If a 86 Am79C961A lower priority DRQ pin than the one currently being used by the PCnet-ISA II is asserted, the PCnet-ISA II will wait 2.6 µs after the deassertion of DACK before re-asserting its DRQ pin. If no lower priority DRQ pin is asserted, the PCnet-ISA II may re-assert its DRQ pin after as short as 1.1 µs following DACK deassertion. The priorities assumed by the PCnet-ISA II are ordered DRQ3, DRQ5, DRQ6, DRQ7, with DRQ3 having highest priority and DRQ7 having the lowest priority. This priority ordering matches that used by typical ISA bus DMA controllers. This adaptive delay scheme allows for fair bus bandwidth sharing when two bus mastering devices, e.g. two PCnet-ISA II devices, are on an ISA bus. The controller using the higher priority DMA channel cannot lock out the controller using the lower priority DMA channel because of the 2.6 µs delay that is inserted before DRQ reassertion when a lower priority DRQ pin is asserted. When there is no lower priority DMA request asserted, the PCnet-ISA II re-requests the bus immediately, providing optimal performance when there is no competition for bus access. Bus Slave Mode The PCnet-ISA II can be configured to be a bus slave for systems that do not support bus mastering or require a local memory to tolerate high bus latencies. In the Bus Slave mode, the I/O map of the PCnet-ISA II is identical to the I/O map when in the Bus Master mode (see I/O Resources section). Hence, the address PROM, controller registers, and Reset por t are accessed through I/O cycles on the ISA bus. However, the initialization block, descriptor rings, and buffers, which are located in system memory when in the Bus Master mode, are located in a local SRAM when in the Bus Slave mode. The local SRAM can be accessed by memory cycles on the ISA bus (Shared Memory architecture) or by I/O cycles on the ISA bus (Programmed I/O mode). Address PROM Cycles External PROM The Address PROM is a small (16 bytes) 8-bit PROM connected to the PCnet-ISA II controller Private Data Bus (PRDB). The PCnet-ISA II controller will support only 8-bit ISA I/O bus cycles for the address PROM; this limitation is transparent to software and does not preclude 16-bit software I/O accesses. An access cycle begins with the Permanent Master driving AEN LOW, driving the addresses valid, and driving IOR active. The PCnet-ISA II controller detects this combination of signals and arbitrates for the Private Data Bus if necessary. IOCHRDY is always driven LOW during address PROM accesses. When the Private Data Bus becomes available, the PCnet-ISA II controller drives APCS active, releases IOCHRDY, turns on the data path from PRD0-7, and enables the SD0-7 drivers (but not SD8-15). During this bus cycle, IOCS16 is not driven active. This condition is maintained until IOR goes inactive, at which time the access cycle ends. Data is removed from SD0-7 within 30 ns. The PCnet-ISA II controller will perform 8-bit ISA bus cycle operation for all resources (registers, PROMs, SRAM) if SBHE has been left unconnected, such as in the case of an 8-bit system like the PC/XT. Ethernet Controller Register Cycles Ethernet controller registers (RAP, RDP, ISACSR) are naturally 16-bit resources but can be configured to operate with 8-bit bus cycles provided the proper protocol is followed. This is programmable by the EEPROM. This means on a read, the PCnet-ISA II controller will only drive the low byte of the system data bus; if an odd byte is accessed, it will be swapped down. The high byte of the system data bus is never driven by the PCnet-ISA II controller under these conditions. On a write, the even byte is placed in a holding register. An odd-byte write is internally swapped up and augmented with the even byte in the holding register to provide an internal 16-bit write. This allows the use of 8-bit I/O bus cycles which are more likely to be compatible with all clones, but requires that both bytes be written in immediate succession. This is accomplished simply by treating the PCnet-ISA II controller controller registers as 16-bit software resources. The motherboard will convert the 16-bit accesses done by software into two sequential 8-bit accesses, an even-byte access followed immediately by an odd-byte access. An access cycle begins with the Permanent Master driving AEN LOW, driving the address valid, and driving IOR or IOW active. The PCnet-ISA II controller detects this combination of signals and drives IOCHRDY LOW. IOCS16 will also be driven LOW if 16-bit I/O bus cycles are enabled. When the register data is ready, IOCHRDY will be released HIGH. This condition is maintained until IOR or IOW goes inactive, at which time the bus cycle ends. The PCnet-ISA II controller will perform 8-bit ISA bus cycle operation for all resources (registers, PROMs, SRAM) if SBHE has been left unconnected, such as in the case of an 8-bit system like the PC/XT. RESET Cycles A read to the reset address causes an PCnet-ISA II controller reset. This has the same effect as asserting the RESET pin on the PCnet-ISA+ controller (which happens on system power up or on a hard boot) except that the T-MAU is NOT reset. The T-MAU will retain its link pass/fail state, disregarding the software RESET command. The subsequent write cycle needed in the NE2100 LANCE- based family of Ethernet cards is not required but does not have any harmful effects. IOCS16 is not asserted in this cycle. Am79C961A 87 ISA Configuration Register Cycles The ISA configuration register is accessed by placing the address of the desired register into the RAP and reading the IDP. The ISACSR bus cycles are identical to all other PCnet-ISA II controller register bus cycles. Boot PROM Cycles The Boot PROM is an 8-bit PROM connected to the PCnet-ISA II controller Private Data Bus (PRDB), and can occupy up to 64 Kbytes of address space. In Shared Memory Mode, an external address comparator is responsible for asserting BPAM to the PCnet-ISA II controller. BPAM is intended to be a perfect decode of the boot PROM address space, i.e. LA17-23, SA16. The LA bus must be latched with BALE in order to provide stable signal for BPAM . REF i nactive must be used by the external logic to gate boot PROM address decoding. This same logic must assert MEMCS16 to the ISA bus if 16-bit Boot PROM bus cycles are desired. In the Bus Slave mode, boot PROM cycles can be programmed to be 8 or 16-bit ISA memory cycles with the BP_16B bit (PnP 0x42). If the BP_16B bit is set, the PCnet-ISA II assumes 16-bit ISA memory cycles for the boot PROM. In this case, the external hardware responsible for generating BPAM must also generate MEMCS16. A 16-bit boot PROM bus cycle begins with the Permanent Master driving the addresses valid and MEMR active. (AEN is not involved in memory cycles). External hardware would assert BPAM and MEMCS16. The PCnet-ISA II controller detects this combination of signals, drives IOCHRDY LOW, and reads two bytes out of the boot PROM. The data bytes read from the PROM are driven by the PCnet-ISA II controller onto SD0-15 and IOCHRDY is released. This condition is maintained until MEMR goes inactive, at which time the access cycle ends. The PCnet-ISA II controller will perform 8-bit ISA bus cycle operation for all resource (registers, PROMs, SRAM) if SBHE has been left unconnected, such as in the case of an 8-bit system like the PC/XT. The BPCS signal generated by the PCnet-ISA II controller is three 20 MHz clock cycles wide (350 ns). Including delays, the Boot PROM has 275 ns to respond to the BPCS signal from the PCnet-ISA II controller. This signal is intended to be connected to the CS pin on the boot PROM, with the PROM OE pin tied to ground. Static RAM Cycles – Shared Memory Architecture In the Shared Memory Architecture mode, the SRAM is an 8-bit device connected to the PCnet-ISA II controller Private Bus, and can occupy up to 64 Kbytes of address space. The SRAM is memory mapped into the ISA memory space at an address range determined by external decode logic. The external address compara- tor is responsible for asserting SMAM to the PCnet-ISA II controller. SMAM is intended to be a perfect decode of the SRAM address space, i.e. LA17-23, SA16 for 64 Kbytes of SRAM. The LA signals must be latched by BALE in order to provide a stable decode for SMAM. The PCnet-ISA II controller assumes 16-bit ISA memory bus cycles for the SRAM, so this same logic must assert MEMCS16 to the ISA bus if 16-bit bus cycles are to be supported. A 16-bit SRAM bus cycle begins with the Permanent Master driving the addresses valid, REF inactive, and either MEMR or MEMW active. (AEN is not involved in memory cycles). External hardware would assert SMAM a nd MEMCS16 . The PCnet-ISA II controller detects this combination of signals and initiates the SRAM access. In a write cycle, the PCnet-ISA II controller stores the data into an internal holding register, allowing the ISA bus cycle to finish normally. The data in the holding register will then be written to the SRAM without the need for ISA bus control. In the event the holding register is already filled with unwritten SRAM data, the PCnet-ISA II controller will extend the ISA write cycle by driving IOCHRDY LOW until the unwritten data is stored in the SRAM. The current ISA bus cycle will then complete normally. In a read cycle, the PCnet-ISA II controller arbitrates for the Private Bus. If it is unavailable, the PCnet-ISA II controller drives IOCHRDY LOW. The PCnet-ISA II controller compares the 16 bits of address on the System Address Bus with that of a data word held in an internal pre-fetch register. If the address does not match that of the prefetched SRAM data, then the PCnet-ISA II controller drives IOCHRDY LOW and reads two bytes from the SRAM. The PCnet-ISA II controller then proceeds as though the addressed data location had been prefetched. If the internal prefetch buffer contains the correct data, then the pre-fetch buffer data is driven on the System Data bus. If IOCHRDY was previously driven LOW due to either Private Data Bus arbitration or SRAM access, then it is released HIGH. The PCnet-ISA II controller remains in this state until MEMR is de-asserted, at which time the PCnet-ISA II controller performs a new prefetch of the SRAM. In this way memory read wait states can be minimized. The PCnet-ISA II controller performs prefetches of the SRAM between ISA bus cycles. The SRAM is prefetched in an incrementing word address fashion. Prefetched data are invalidated by any other activity on the Private Bus, including Shared Memory Writes by either the ISA bus or the network interface, and also address and boot PROM reads. 88 Am79C961A The only way to configure the PCnet-ISA II controller for 8-bit ISA bus cycles for SRAM accesses is to configure the entire PCnet-ISA II controller to support only 8-bit ISA bus cycles. This is accomplished by leaving the SBHE pin disconnected. The PCnet-ISA II controller will perform 8-bit ISA bus cycle operation for all resources (registers, PROMs, SRAM) if SBHE h as never been driven active since the last RESET, such as in the case of an 8-bit system like the PC/XT. In this case, the external address decode logic must not assert MEMCS16 to the ISA bus, which will be the case if MEMCS16 is left unconnected. It is possible to manufacture a dual 8/16 bit PCnet-ISA II controller adapter card, as the MEMCS16 and SBHE signals do not exist in the PC/XT environment. At the memory device level, each SRAM Private Bus read cycle takes two 50 ns clock periods for a maximum read access time of 75 ns. The timing looks like this: Address and data are valid 20 ns after the rising edge of the first clock period. SRWE goes active 20 ns after the falling edge of the first clock period. SRWE goes inactive 20 ns after the falling edge of the third clock period. Address and data remain valid until the end of the third clock period. Rise and fall times are nominally 5 ns. Non-negative setup and hold times for address and data with respect to SRWE are guaranteed. SRWE has a pulse width of typically 100 ns, minimum 75 ns. Static RAM Cycles – Programmed I/O Architecture In the Programmed I/O Architecture mode, the SRAM is an 8-bit device connected to the PCnet-ISA II controller Private Bus, and can occupy up to 64 Kbytes of address space. The SRAM is accessed through the ISACSR0 and ISACSR1 registers which serve as the SRAM Data port and SRAM Address pointer, respectively. Since the ISACSRs are used to access the SRAM, simple I/O accesses (to RAP and IDP) which are decoded by the PCnet-ISA II are used to access the SRAM without any external decoding logic. The RAP and IDP ports are naturally 16-bit resources and can be accessed with 16-bit ISA I/O cycles if the IO_MODE bit (PnP 0xF0) is set. As discussed in the Ethernet Controller Register Cycles section, 8-bit I/O cycles are also allowed, provided the proper protocol is followed. This protocol requires that byte accesses must be performed in pairs, with the even byte access always being followed by associated odd byte access. In the Programmed I/O architecture mode, when a c c e s s i n g t h e S R A M D a t a Po r t i n p a r t i c u l a r (ISACSR0), the restrictions on byte accesses are slightly different. Even byte accesses (accesses where A0 = 0, SBHE = 1) may be performed to ISACSR0 without any restriction. A corresponding odd byte access need not be performed following the even byte access as is required when accessing all other controller registers. In fact, odd byte accesses (accesses where A0 = 1, SBHE = 1) may not be performed to ISACSR0, except when they are the result of a software 16-bit access that are automatically converted to two byte accesses by motherboard logic. Since the internal PCnet-ISA II registers are used to access the SRAM in the Programmed I/O architecture mode, the access cycle on the ISA bus is identical to that described in the Ethernet Controller Register Cycles section. To minimize the number of I/O cycles required to access the SRAM, the PCnet-ISA II auto-increments the SRAM Address Pointer (ISACSR1) by one or two following every read or write to the SRAM Data Port (ISACSR0). If a single byte read or write to the SRAM Data Port occurs, the SRAM Address Pointer is automatically incremented by 1. If a word read or write to the SRAM Data Port occurs, the SRAM Address Pointer is automatically incremented by 2. This allows XTAL1 (20 MHz) Address SROE 19364B-18 Static RAM Read Cycle The address and SROE go active within 20 ns of the clock going HIGH. Data is required to be valid 5 ns before the end of the second clock cycle. Address and SROE have a 0 ns hold time after the end of the second clock cycle. Note that the PCnet-ISA II controller does not normally provide a separate SRAM CS signal; SRAM CS must always be asserted. SRAM Private Bus write cycles require three 50 ns clock periods to guarantee non-negative address setup and hold times with regard to SRWE. The timing is illustrated as follows: XTAL1 (20 MHz) Address/ Data SRWE Static 19364B-19 Am79C961A 89 reads and writes to adjacent ascending addresses in the SRAM to be performed without intervening writes to the SRAM Address Pointer. Since buffer accesses comprise a high percentage of all accesses to the SRAM, and buffer accesses are typically performed in adjacent ascending order, the auto-increment of the SRAM Address Pointer reduces the required ISA bus cycles significantly. In addition to the auto-incrementing of the SRAM Address pointer, the PCnet-ISA II performs write posting on writes to the SRAM and read prefetching on reads from the SRAM to maximize performance in the Programmed I/O architecture mode. Write Posting: When a write cycle to the SRAM Data Port occurs, the PCnet-ISA II controller stores the data into an internal holding register, allowing the ISA bus cycle to finish normally. The data in the holding register will then be written to the SRAM without the need for ISA bus control. In the event that the holding register is already filled with unwritten SRAM data, the PCnet-ISA II controller will extend the ISA write cycle by driving OCHRDY LOW until the unwritten data is stored in the SRAM. Once the data is written into the SRAM, the new write data is stored into the internal holding register and IOCHRDY is released allowing the ISA bus cycle to complete. Read Prefetching: To gain performance on read accesses to the SRAM, the PCnet-ISA II performs prefetches of the SRAM after every read from the SRAM Data Port. The prefetch is performed using the speculated address that results from the auto-increment that occurs on the SRAM Address Pointer following every access to the SRAM Data Port. Following every read access, the 16-bit word following the just-read SRAM byte or word is prefetched and placed in a holding register. If a word read from the SRAM Data Port occurs before a “prefetch invalidation event” occurs, the prefetched word is driven onto the SD[15:0] pins without a wait state (no IOCHRDY LOW assertion). A “prefetch invalidation event” is defined as any activity on the Private Bus other than SRAM reads. This includes SRAM writes by either the ISA bus or the network interface, address or boot PROM reads, or any write to the SRAM Address Pointer. The PCnet-ISA II interface to the SRAM in the Programmed I/O architecture mode is identical to that in the Shared Memory Architecture mode. Hence, the SRAM Read and Write cycle descriptions and diagrams shown in the “Static RAM Cycles – S hared Memory Architecture” section apply. Transmit Function Programming Automatic transmit features, such as retry on collision, FCS generation/transmission, and pad field insertion, can all be programmed to provide flexibility in the (re-)transmission of messages. Disable retry on collision (DRTY) is controlled by the DRTY bit of the Mode register (CSR15) in the initialization block. Automatic pad field insertion is controlled by the APAD_XMT bit in CSR4. If APAD_XMT is set, automatic pad field insertion is enabled, the DXMTFCS feature is over-ridden, and the 4-byte FCS will be added to the transmitted frame unconditionally. If APAD_XMT is cleared, no pad field insertion will take place and runt packet transmission is possible. The disable FCS generation/transmission feature can be programmed dynamically on a frame by frame basis. See the ADD_FCS description of TMD1. Transmit FIFO Watermark (XMTFW in CSR80) sets the point at which the BMU (Buffer Management Unit) requests more data from the transmit buffers for the FIFO. This point is based upon how many 16-bit bus transfers (2 bytes) could be performed to the existing empty space in the transmit FIFO. Transmit Start Point (XMTSP in CSR80) sets the point when the transmitter actually tries to go out on the media. This point is based upon the number of bytes written to the transmit FIFO for the current frame. When the entire frame is in the FIFO, attempts at transmission of preamble will commence regardless of the value in XMTSP. The default value of XMTSP is 10b, meaning 64 bytes full. Automatic Pad Generation Transmit frames can be automatically padded to extend them to 64 data bytes (excluding preamble). This allows the minimum frame size of 64 bytes (512 bits) for 802.3/Ethernet to be guaranteed with no software intervention from the host/controlling process. Setting the APAD_XMT bit in CSR4 enables the automatic padding feature. The pad is placed between the LLC data field and FCS field in the 802.3 frame. FCS is always added if the frame is padded, regardless of the state of DXMTFCS. The transmit frame will be padded by bytes with the value of 00h. The default value of APAD_XMT is 0, and this will disable auto pad generation after RESET. It is the responsibility of upper layer software to correctly define the actual length field contained in the message to correspond to the total number of LLC Data bytes encapsulated in the packet (length field as defined in the IEEE 802.3 standard). The length value contained in the message is not used by the PCnet-ISA II controller to compute the actual number of pad bytes Transmit Operation The transmit operation and features of the PCnet-ISA II controller are controlled by programmable options. 90 Am79C961A to be inserted. The PCnet-ISA II controller will append pad bytes dependent on the actual number of bits transmitted onto the network. Once the last data byte of the frame has completed prior to appending the FCS, the PCnet-ISA II controller will check to ensure that 544 bits have been transmitted. If not, pad bytes are added to extend the frame size to this value, and the FCS is then added. The 544 bit count is derived from the following: Minimum frame size (excluding preamble, including FCS) 64 bytes 512 bits Preamble/SFD size 8 bytes 64 bits FCS size 4 bytes 32 bits To be classed as a minimum-size frame at the receiver, the transmitted frame must contain: Preamble + (Min Frame Size + FCS) bits generate and append the FCS to the transmitted frame. I f t h e a u t o m a t i c p a d d i n g fe a t u r e i s i n vo k e d (APAD_XMT is SET in CSR4), the FCS will be appended by the PCnet-ISA II controller regardless of the state of DXMTFCS. Note that the calculated FCS is transmitted most-significant bit first. The default value of DXMTFCS is 0 after RESET. Transmit Exception Conditions Exception conditions for frame transmission fall into two distinct categories; those which are the result of normal network operation, and those which occur due to abnormal network and/or host related events. Normal events which may occur and which are handled autonomously by the PCnet-ISA II controller are basically collisions within the slot time with automatic retry. The PCnet-ISA II controller will ensure that collisions which occur within 512 bit times from the start of transmission (including preamble) will be automatically retried with no host intervention. The transmit FIFO ensures this by guaranteeing that data contained within the FIFO will not be overwritten until at least 64 bytes (512 bits) of data have been successfully transmitted onto the network. If 16 total attempts (initial attempt plus 15 retries) fail, the PCnet-ISA II controller sets the RTRY bit in the current transmit TDTE in host memory (TMD2), gives up ownership (sets the OWN bit to zero) for this packet, and processes the next packet in the transmit ring for transmission. At the point that FCS is to be appended, the transmitted frame should contain: Preamble 64+ + (Min Frame Size - FCS) bits (512- 32) bits A minimum-length transmit frame from the PCnet-ISA II controller will, therefore, be 576 bits after the FCS is appended. Transmit FCS Generation Automatic generation and transmission of FCS for a transmit frame depends on the value of DXMTFCS bit in CSR15. When DXMTFCS = 0 the transmitter will Preamble 1010....1010 56 Bits SYNC 10101011 8 Bits Dest. ADDR 6 Bytes SRCE. ADDR. 6 Bytes Length 2 Bytes LLC Data Pad FCS 4 Bytes 46-1500 Bytes 19364B-20 ISO 8802-3 (IEEE/ANSI 802.3) Data Frame Am79C961A 91 Abnormal network conditions include: s Loss of carrier s Late collision s SQE Test Error (Does not apply to 10BASE-T port.) These should not occur on a correctly configured 802.3 network, and will be reported if they do. When an error occurs in the middle of a multi-buffer frame transmission, the error status will be written in the current descriptor. The OWN bit(s) in the subsequent descriptor(s) will be reset until the STP (the next frame) is found. Loss of Carrier A loss of carrier condition will be reported if the PCnet-ISA II controller cannot observe receive activity while it is transmitting on the AUI port. After the PCnet-ISA II controller initiates a transmission, it will expect to see data “looped back” on the DI± pair. This will internally generate a “carrier sense,” indicating that the integrity of the data path to and from the MAU is intact, and that the MAU is operating correctly. This “carrier sense” signal must be asserted before the end of the transmission. If “carrier sense” does not become active in response to the data transmission, or becomes inactive before the end of transmission, the loss of carrier (LCAR) error bit will be set in TMD2 after the frame has been transmitted. The frame will not be re-tried on the basis of an LCAR error. In 10BASE-T mode LCAR will indicate that Jabber or Link Fail state has occurred. Late Collision A late collision will be reported if a collision condition occurs after one slot time (512 bit times) after the transmit process was initiated (first bit of preamble commenced). The PCnet-ISA II controller will abandon the transmit process for the particular frame, set Late Collision (LCOL) in the associated TMD3, and process the next transmit frame in the ring. Frames experiencing a late collision will not be re-tried. Recovery from this condition must be performed by upper-layer software. SQE Test Error During the inter packet gap time following the completion of a transmitted message, the AUI CI ± p air is asserted by some transceivers as a self-test. The integral Manchester Encoder/Decoder will expect the SQE Test Message (nominal 10 MHz sequence) to be returned via the CI± pair within a 40 network bit time period after DI± pair goes inactive. If the CI± inputs are not asserted within the 40 network bit time period following the completion of transmission, then the PCnet-ISA II controller will set the CERR bit in CSR0. CERR will be asserted in 10BASE-T mode after transmit if T-MAU is in Link Fail state. CERR will never cause INTR to be activated. It will, however, set the ERR bit in CSR0. Host related transmit exception conditions include BUFF and UFLO as described in the Transmit Descriptor section. Receive Operation The receive operation and features of the PCnet-ISA II controller are controlled by programmable options. Receive Function Programming Automatic pad field stripping is enabled by setting the ASTRP_RCV bit in CSR4; this can provide flexibility in the reception of messages using the 802.3 frame format. All receive frames can be accepted by setting the PROM bit in CSR15. When PROM is set, the PCnet-ISA II controller will attempt to receive all messages, subject to minimum frame enforcement. Promiscuous mode overrides the effect of the Disable Receive Broadcast bit on receiving broadcast frames. The point at which the BMU will start to transfer data from the receive FIFO to buffer memory is controlled by the RCVFW bits in CSR80. The default established during reset is 10b, which sets the threshold flag at 64 bytes empty. Automatic Pad Stripping During reception of an 802.3 frame the pad field can be stripped automatically. ASTRP_RCV (bit 10 in CSR4) = 1 enables the automatic pad stripping feature. The pad field will be stripped before the frame is passed to the FIFO, thus preserving FIFO space for additional frames. The FCS field will also be stripped, since it is computed at the transmitting station based on the data and pad field characters, and will be invalid for a receive frame that has had the pad characters stripped. The number of bytes to be stripped is calculated from the embedded length field (as defined in the IEEE 802.3 definition) contained in the frame. The length indicates the actual number of LLC data bytes contained in the message. Any received frame which contains a length field less than 46 bytes will have the pad field stripped (if ASTRP_RCV is set). Receive frames which have a length field of 46 bytes or greater will be passed to the host unmodified. Since any valid Ethernet Type field value will always be greater than a normal 802.3 Length field (≥46), the PCnet-ISA II controller will not attempt to strip valid Ethernet frames. Note that for some network protocols the value passed in the Ethernet Type and/or 802.3 Length field is not compliant with either standard and may cause problems. The diagram below shows the byte/bit ordering of the received length field for an 802.3 compatible frame format. 92 Am79C961A 56 Bits Preamble 1010....1010 8 Bits SYNCH 10101011 6 Bytes Dest. ADDR. 6 Bytes Srce. ADDR. 2 Bytes Length LLC DATA Bytes 4 Bytes Pad FCS 1–1500 Bytes 45–0 Bytes Start of Packet at Time= 0 Bit 0 Bit Bit 70 Bit 7 Increasing Time Most Significant Byte Least Significant Byte 19364B-21 IEEE/ANSI 802.3 Frame and Length Field Transmission Order Receive FCS Checking Reception and checking of the received FCS is performed automatically by the PCnet-ISA II controller. Note that if the Automatic Pad Stripping feature is enabled, the received FCS will be verified against the value computed for the incoming bit stream including pad characters, but it will not be passed to the host. If a FCS error is detected, this will be reported by the CRC bit in RMD1. Receive Exception Conditions Exception conditions for frame reception fall into two distinct categories; those which are the result of normal network operation, and those which occur due to abnormal network and/or host related events. Normal events which may occur and which are handled autonomously by the PCnet-ISA II controller are basically collisions within the slot time and automatic runt packet rejection. The PCnet-ISA II controller will ensure that collisions which occur within 512 bit times from the start of reception (excluding preamble) will be automatically deleted from the receive FIFO with no host intervention. The receive FIFO will delete any frame which is composed of fewer than 64 bytes provided that the Runt Packet Accept (RPA bit in CSR124) feature has not been enabled. This criteria will be met regardless of whether the receive frame was the first (or only) frame in the FIFO or if the receive frame was queued behind a previously received message. Abnormal network conditions include: s FCS errors s Late collision These should not occur on a correctly configured 802.3 network and will be reported if they do. Host related receive exception conditions include MISS, BUFF, and OFLO. These are described in the Receive Descriptor section. Loopback Operation Loopback is a mode of operation intended for system diagnostics. In this mode, the transmitter and receiver are both operating at the same time so that the controller receives its own transmissions. The controller provides two types of internal loopback and three types of external loopback. In internal loopback mode, the transmitted data can be looped back to the receiver at one of two places inside the controller without actually transmitting any data to the external network. The receiver will move the received data to the next receive buffer, where it can be examined by software. Alternatively, external loopback causes transmissions to go off-chip. For the AUI port, frame transmission occurs normally and assumes that an external MAU will loop the frame back to the chip. For the 10BASE-T port, two external loopback options are available, both of which require a valid link pass state and both of which transmit data frames at the RJ45 interface. Selection of these modes is defined by the TMAU_LOOPE bit in ISACSR2. One option loops the data frame back inside the chip, and is compatible with a ‘live’ network. The Am79C961A 93 other option requires an external device (such as a ‘loopback plug’) to loop the data back to the chip, a function normally not available on a 10BASE-T network. The PCnet-ISA II chip has two dedicated FCS generators, eliminating the traditional LANCE limitations on loopback FCS operation. The receive FCS generation logic is always enabled. The transmit FCS generation logic can be disabled (to emulate LANCE type loopback operation) by setting the DXMTFCS bit in the Mode register (CSR15). In this configuration, software must generate the FCS and append the four FCS bytes to the transmit frame data. The loopback facilities of the MAC Engine allow full operation to be verified without disturbance to the network. Loopback operation is also affected by the state of the Loopback Control bits (LOOP, MENDECL, and INTL) in CSR15. This affects whether the internal MENDEC is considered part of the internal or external loop- backpath. The receive FCS generation logic in the PCnet-ISA II chip is used for multicast address detection. Since this FCS logic is always enabled, there are no restrictions to the use of multicast addressing while in loopback mode. When performing an internal loopback, no frame will be transmitted to the network. However, when the PCnet-ISA II controller is configured for internal loopback the receiver will not be able to detect network traffic. External loopback tests will transmit frames onto the network if the AUI port is selected, and the PCnet-ISA II controller will receive network traffic while configured for external loopback when the AUI port is selected. Runt Packet Accept is automatically enabled when any loopback mode is invoked. Loopback mode can be performed with any frame size. Runt Packet Accept is internally enabled (RPA bit in CSR124 is not affected) when any loopback mode is invoked. This is to be backwards compatible to the LANCE (Am7990) software. Signal COL FDLS JAB LNKST RCV RVPOL Behavior Active during collision activity on the network Active when Full Duplex operation is enabled and functioning on the selected network port Active when the PCnet-ISA II is jabbering on the network Active during Link OK Not active during Link Down Active while receiving data Active during receive polarity is OK Not active during reverse receive polarity RCVADDM Active during Receive with Address Match XMT Active while transmitting data Each status signal is ANDed with its corresponding enable signal. The enabled status signals run to a common OR gate: FDLS FDLSE RCVM RCVM E XMT XMT E RVPOL RVPOL E RCV RCV E JAB JAB E COL COL E RCVADDM RCVADDE AND AND OR AND AND AND AND AND AND 19364B-22 To Pulse Stretcher LEDs The PCnet-ISA II controller’s LED control logic allows programming of the status signals, which are displayed on 3 LED outputs. One LED (LED0) is dedicated to displaying 10BASE-T Link Status. The status signals available are Collision, Jabber, Receive, Receive Polarity, Transmit, Receive Address Match, and Full Duplex Link Status. If more than one status signal is enabled, they are ORed together. An optional pulse stretcher is available for each programmable output. This allows emulation of the TPEX (Am79C98) and TPEX + (Am79C100) LED outputs. LED Control Logic The output from the OR gate is run through a pulse stretcher, which consists of a 3-bit shift register clocked at 38 Hz. The data input of the shift register is at logic 0. The OR gate output asynchronously sets all three bits of the shift register when its output goes active. The output of the shift register controls the associated LEDx pin. Thus, the pulse stretcher provides an LED output of 52 ms to 78 ms. 94 Am79C961A Refer to the section “ISA Bus Configuration Registers” for information on LED control via the ISACSRs. deactivated by setting the STOP bit or resetting the MP_ENBL bit (CSR5, bit 2). Interrupt Indication. Interrupt pin could be activated by the receive of the Magic Packet. The MP_I_ENBL bit (CSR5, bit 3) and IENA bit (CSR0, bit 6) should be set to enable this feature. Bit 1 Name MP_MODE Description Magic Packet Mode. Setting this bit is a prerequisite for entering the Magic Packet mode. It also redefines the SLEEP pin to be a Magic Packet enable pin. Read/Write accessible always. It is cleared by asserting the RESET pin, or reading the RESET register. Magic Packet Enable. This bit when set, will force the PCnet-ISA II into the Magic Packet mode. Read/Write accessible always. It is cleared by asserting the RESET pin or reading the RESET register. Magic Packet Interrupt Enable. Acts as an unmask bit for the MP_INT (CSR5, bit 4). Read/ Write accessible always. It is cleared by asserting the RESET pin or reading the RESET register, or setting the STOP bit. Magic Packet Receive Interrupt. Will be set when a Magic Packet has been received. Writing a “one” will clear this bit. It is cleared by asserting the RESET pin, or reading the RESET register. Magic Packet LED Enable. When set, the LED output will be asserted to indicate that a Magic Packet has been received. MAGIC PACKET OPERATION In the Magic Packet mode, PCnet-ISA II completes any transmit and receive operations in progress, suspends normal activity, and enters into a state where only a Magic Packet could be detected. A Magic Packet frame is a frame that contains a data sequence which repeats the Physical Address (PADR[47:00]) at least sixteen times frame sequentially, with bit[00] received first. In Magic Packet suspend mode, the PCnet-ISA II remains powered up. Slave accesses to the PCnet-ISA II are still possible, the same as any other mode. All of the received packets are flushed from the receive FIFO. An LED and/or interrupt pin could be activated, indicating the receive of a Magic Packet frame. This indication could be used for a variety of management tasks. Magic Packet Mode Activation This mode can be enabled by either software or external hardware means, but in either case, the MP_MODE bit (CSR5, bit 1) must be set first. Hardware Activation. T his is done by driving the SLEEP pin low. Deasserting the SLEEP pin will return the PCnet-ISA II to normal operation. Software Activation. T his is done by setting the MP_ENBL bit (CSR5, bit 2). Resetting this bit will return the PCnet-ISA II to normal operation. Magic Packet Receive Indicators The reception of a Magic Packet can be indicated either through one of the LEDs 1, 2 or 3, and/or the activation of the interrupt pin. MP_INT bit (CSR5, bit 4) will also be set upon the receive of the Magic Packet. LED Indication. Either one of the LEDs 1, 2, or 3 could be activated by the receive of the Magic Packet. The “Magic Packet enable” bit (bit 9) in the ISACSR 5, 6 or 7 should be set to enable this feature. Note that the polarity of the LED2 could be controlled by the LEDXOR bit (ISACSR6, bit 14). The LED could be 2 MP_ENBL 3 MP_I_ENBL 4 MP_INT 9 MP Am79C961A 95 PCNET-ISA II CONTROLLER REGISTERS The PCnet-ISA II controller implements all LANCE (Am7990) registers, plus a number of additional registers. The PCnet-ISA II controller registers are compatible with the original LANCE, but there are some places where previously reserved LANCE bits are now used by the PCnet-ISA II controller. If the reserved LANCE bits were used as recommended, there should be no compatibility problems. 13 CERR Register Access Internal registers are accessed in a two-step operation. First, the address of the register to be accessed is written into the register address port (RAP). Subsequent read or write operations will access the register pointed to by the contents of the RAP. The data will be read from (or written to) the selected register through the data port, either the register data port (RDP) for control and status registers (CSR) or the ISACSR register data por t (IDP) for ISA control and status registers (ISACSR). RAP: Register Address Port Bit 15-7 6-0 Name RES RAP Description Reserved locations. Read and written as zeroes. Register Address Port select. Selects the CSR or ISACSR location to be accessed. RAP is cleared by RESET. 12 MISS Control and Status Registers CSR0: PCnet-ISA II Controller Status Register Bit 15 Name ERR Description Error is set by the ORing of BABL, CERR, MISS, and MERR. ERR remains set as long as any of the error flags are true. ERR is read only; write operations are ignored. Babble is a transmitter time-out error. It indicates that the transmitter has been on the channel longer than the time required to send the maximum length frame. BABL will be set if 1519 bytes or greater are transmitted. When BABL is set, IRQ is asserted if IENA = 1 and the mask bit BABLM (CSR3.14) is clear. BABL assertion will set the ERR bit. BABL is set by the MAC layer and cleared by writing a “1". Writing a “0" has no effect. BABL 11 MERR 14 BABL is cleared by RESET or by setting the STOP bit. Collision Error indicates that the collision inputs to the AUI port failed to activate within 20 network bit times after the chip terminated transmission (SQE Test). This feature is a transceiver test feature. CERR will be set in 10BASE-T mode during transmit if in Link Fail state. CERR assertion will not result in an interrupt being generated. CERR assertion will set the ERR bit. CERR is set by the MAC layer and cleared by writing a “1". Writing a “0" has no effect. CERR is cleared by RESET or by setting the STOP bit. Missed Frame is set when PCnet-ISA II controller has lost an incoming receive frame because a Receive Descriptor was not available. This bit is the only indication that receive data has been lost since there is no receive descriptor available for status information. When MISS is set, IRQ is asserted if IENA = 1 and the mask bit MISSM (CSR3.12) is clear. MISS assertion will set the ERR bit. MISS is set by the Buffer Management Unit and cleared by writing a “1". Writing a “0" has no effect. MISS is cleared by RESET or by setting the STOP bit. Memory Error is set when PCnet-ISA II controller is a bus master and has not received DACK assertion after 50 µs after DRQ assertion. Memory Error indicates that PCnet-ISA II controller is not receiving bus mastership in time to prevent overflow/underflow conditions in the receive and transmit FIFOs. (MERR indicates a slightly different condition for the LANCE; for the LANCE MERR occurs when READY has not been asserted 25.6 µs after the address has been asserted.) When MERR is set, IRQ is asserted if IENA = 1 and the mask bit MERRM (CSR3.11) is clear. MERR assertion will set the ERR bit. 96 Am79C961A 10 RINT 9 TINT 8 IDON 7 INTR MERR is set by the Bus Interface Unit and cleared by writing a “1". Writing a “0" has no effect. MERR is cleared by RESET or by setting the STOP bit. Receive Interrupt is set after reception of a receive frame and toggling of the OWN bit in the last buffer in the Receive Descriptor Ring. When RINT is set, IRQ is asserted if IENA = 1 and the mask bit RINTM (CSR3.10) is clear. RINT is set by the Buffer Management Unit after the last receive buffer has been updated and cleared by writing a “1". Writing a “0" has no effect. RINT is cleared by RESET or by setting the STOP bit. Transmit Interrupt is set after transmission of a transmit frame and toggling of the OWN bit in the last buffer in the Transmit Descriptor Ring. When TINT is set, IRQ is asserted if IENA = 1 and the mask bit TINTM (CSR3.9) is clear. TINT is set by the Buffer Management Unit after the last transmit buffer has been updated and cleared by writing a “1". Writing a “0" has no effect. TINT is cleared by RESET or by setting the STOP bit. Initialization Done indicates that the initialization sequence has completed. When IDON is set, PCnet-ISA II controller has read the Initialization block from memory. When IDON is set, IRQ is asserted if IENA = 1 and the mask bit IDONM (CSR3.8) is clear. IDON is set by the Buffer Management Unit after the initialization block has been read from memory and cleared by writing a “1". Writing a “0" has no effect. IDON is cleared by RESET or by setting the STOP bit. Interrupt Flag indicates that one or more of the following interrupt causing conditions has occurred: BABL, MISS, MERR, MPCO, RCVCCO, RINT, TINT, IDON, JAB or TXSTRT; and its associated mask bit is clear. If 6 IENA 5 RXON 4 TXON 3 TDMD IENA = 1 and INTR is set, IRQ will be active. INTR is cleared automatically when the condition that caused interrupt is cleared. INTR is read only. INTR is cleared by RESET or by setting the STOP bit. Interrupt Enable allows IRQ to be active if the Interrupt Flag is set. If IENA = “0" then IRQ will be disabled regardless of the state of INTR. IENA is set by writing a “1" and cleared by writing a “0". IENA is cleared by RESET or by setting the STOP bit. Receive On indicates that the Receive function is enabled. RXON is set if DRX (CSR15.0) = “0" after the START bit is set. If INIT and START are set together, RXON will not be set until after the initialization block has been read in. RXON is read only. RXON is cleared by RESET or by setting the STOP bit. Transmit On indicates that the Transmit function is enabled. TXON is set if DTX (CSR15.1) = “0" after the START bit is set. If INIT and START are set together, TXON will not be set until after the initialization block has been read in. TXON is read only. TXON is cleared by RESET or by setting the STOP bit. Transmit Demand, when set, causes the Buffer Management Unit to access the Transmit Descriptor Ring without waiting for the poll-time counter to elapse. If TXON is not enabled, TDMD bit will be reset and no Transmit Descriptor Ring access will occur. TDMD is required to be set if the DPOLL bit in CSR4 is set; setting TDMD while DPOLL = 0 merely hastens the PCnet-ISA II controller’s response to a Transmit Descriptor Ring Entry. TDMD is set by writing a “1". Writing a “0" has no effect. TDMD will be cleared by the Buffer Management Unit when it fetches a Transmit Descriptor. Am79C961A 97 2 STOP 1 STRT 0 INIT TDMD is cleared by RESET or by setting the STOP bit. STOP assertion disables the chip from all external activity. The chip remains inactive until either STRT or INIT are set. If STOP, STRT and INIT are all set together, STOP will override STRT and INIT. STOP is set by writing a “1" or by RESET. Writing a “0" has no effect. STOP is cleared by setting either STRT or INIT. STRT assertion enables PCnetISA II controller to send and receive frames, and perform buffer management operations. Setting STRT clears the STOP bit. If STRT and INIT are set together, PCnet-ISA II controller initialization will be performed first. STRT is set by writing a “1". Writing a “0" has no effect. STRT is cleared by RESET or by setting the STOP bit. INIT assertion enables PCnet-ISA II controller to begin the initialization procedure which reads in the initialization block from memory. Setting INIT clears the STOP bit. If STRT and INIT are set together, PCnet-ISA II controller initialization will be performed first. INIT is not cleared when the initialization sequence has completed. INIT is set by writing a “1". Writing a “0" has no effect. INIT is cleared by RESET or by setting the STOP bit. Description Lower address of the Initialization address register. Bit location 0 must be zero. Whenever this register is written, CSR16 is updated with CSR1’s contents. Read/Write accessible only when the STOP or SPND bits are set. Unaffected by RESET. Description Reserved locations. Read and written as zero. Upper 8 bits of the address of the Initialization Block. Bit locations 15-8 must be written with zeros. Whenever this register is written, CSR17 is updated with CSR2’s contents. Read/Write accessible only when the STOP or SPND bits are set. Unaffected by RESET. CSR3: Interrupt Masks and Deferral Control Bit 15 14 Name RES BABLM Description Reserved location. Written as zero and read as undefined. Babble Mask. If BABLM is set, the BABL bit in CSR0 will be masked and will not set INTR flag in CSR0. BABLM is cleared by RESET and is not affected by STOP. Reserved location. Written as zero and read as undefined. Missed Frame Mask. If MISSM is set, the MISS bit in CSR0 will be masked and will not set INTR flag in CSR0. MISSM is cleared by RESET and is not affected by STOP. Memory Error Mask. If MERRM is set, the MERR bit in CSR0 will be masked and will not set INTR flag in CSR0. MERRM is cleared by RESET and is not affected by STOP. Receive Interrupt Mask. If RINTM is set, the RINT bit in CSR0 will be masked and will not set INTR flag in CSR0. RINTM is cleared by RESET and is not affected by STOP. Transmit Interrupt Mask. If TINTM is set, the TINT bit in CSR0 will be masked and will not set INTR flag in CSR0. TINTM is cleared by RESET and is not affected by STOP. Initialization Done Mask. If IDONM is set, the IDON bit in CSR0 will be masked and will not set INTR flag in CSR0. IDONM is cleared by RESET and is not affected by STOP. Reserved locations. Written as zero and read as undefined. Disable Transmit Stop on Underflow error. 7-0 IADR [23:16] 13 12 RES MISSM 11 MERRM 10 RINTM CSR1: IADR[15:0] Bit Name 9 TINTM 15-0 IADR [15:0] 8 IDONM CSR2: IADR[23:16] Bit 15-8 Name RES 7 6 RES DXSUFLO 98 Am79C961A 5 LAPPEN When DXSUFLO is set to ZERO, the transmitter is turned off when an UFLO error occurs (CSR0, TXON = 0). When DXSUFLO is set to ONE, the PCnet-ISA II controller gracefully recovers from an UFLO error. It scans the transmit descriptor ring until it finds the start of a new frame and starts a new transmission. Read/Write accessible always. DXSUFLO is cleared by asserting the RESET pin or reading the Reset register and is not affected by STOP. Look Ahead Packet Processing (LAPPEN). When set to a one, the LAPPEN bit will cause the PCnet-ISA II controller to generate an interrupt following the descriptor write operation to the first buffer of a receive packet. This interrupt will be generated in addition to the interrupt that is generated following the descriptor write operation to the last buffer of a receive packet. The interrupt will be signaled through the RINT bit of CSR0. Setting LAPPEN to a one also enables the PCnet-ISA II controller to read the STP bit of the receive descriptors. PCnet-ISA II controller will use STP information to determine where it should begin writing a receive packet’s data. Note that while in this mode, the PCnet-ISA II controller can write intermediate packet data to buffers whose descriptors do not contain STP bits set to one. Following the write to the last descriptor used by a packet, the PCnet-ISA II controller will scan through the next descriptor entries to locate the next STP bit that is set to a one. The PCnet-ISA II controller will begin writing the next packet’s data to the buffer pointed to by that descriptor. Note that because several descriptors may be allocated by the host for each packet, and not all messages may need all of the descriptors that are allocated between descriptors that contain STP = one, then some descriptors/buffers may be skipped in the ring. While performing the 4 DXMT2PD 3 EMBA search for the next STP bit that is set to one, the PCnet-ISA II controller will advance through the receive descriptor ring regardless of the state of ownership bits. If any of the entries that are examined during this search indicate OWN = one, PCnet-ISA II will RESET the OWN bit to zero in these entries. If a scanned entry indicates host ownership with STP=“0", then the PCnet-ISA II controller will not alter the entry, but will advance to the next entry. When the STP bit is found to be true, but the descriptor that contains this setting is not owned by the PCnet-ISA II controller, then the PCnet-ISA II controller will stop advancing through the ring entries and begin periodic polling of this entry. When the STP bit is found to be true, and the descriptor that contains this setting is owned by the PCnet-ISA II controller, then the PCnet-ISA II controller will stop advancing through the ring entries, store the descriptor information that is has just read, and wait for the next receive to arrive. This behavior allows the host software to pre-assign buffer space in such a manner that the “header” portion of a receive packet will always be written to a particular memory area, and the “data” portion of a receive packet will always be written to a separate memory area. The interrupt is generated when the “header” bytes have been written to the “header” memory area. Read/Write accessible always. The LAPPEN bit will be reset zero by RESET and will unaffected by the STOP. See Appendix E for more information on LAPP. Disable Transmit Two Part Deferral. (Described in the Media Access Management section). If DXMT2PD is set, Transmit Two Part Deferral will be disabled. DXMT2PD is cleared by RESET and is not affected by STOP. Enable Modified Back-off Algorithm. If EMBA is set, a modified Am79C961A 99 back-off algorithm is implemented as described in the Media Access Management section. Read/Write accessible. EMBA is cleared by RESET and is not affected by STOP. 2-0 RES Reserved locations. Written as zero and read as undefined. CSR4: Test and Features Control Bit 15 Name ENTST Description Enable Test Mode operation. When ENTST is set, writing to test mode registers CSR124 and CSR126 is allowed, and other register test functions are enabled. In order to set ENTST, it must be written with a “1" during the first write access to CSR4 after RESET. Once a “0" is written to this bit location, ENTST cannot be set until after the PCnet-ISA II controller is reset. ENTST is cleared by RESET. When DMAPLUS = “1", the burst transaction counter in CSR80 is disabled. If DMAPLUS = “0", the burst transaction counter is enabled. Caution: When using DMAPLUS AND/OR TIMER bits in a PC environment, care must be taken not to hold the bus for more than the required refresh time. DMAPLUS is cleared by RESET. Timer Enable Register. If TIMER is set, the Bus Activity Timer register (CSR82) is enabled and the PCnet-ISA II may perform any combination of accesses (buffer reads, buffer writes, descriptor reads, and descriptor writes) during a single bus mastership period. The bus is held until either the Bus Activity Timer expires or there are no further pending operations to be performed. The PCnet-ISA II determines whether there are further pending bus operations by waiting approximately 1 µs after the completion of every bus operation (e.g. a descriptor or FIFO access). If, during the 1 µs period, no further bus operations are requested by the internal Buffer Management Unit, the PCnet-ISA II determines that 12 DPOLL 14 DMAPLUS 11 APAD_XMT 13 TIMER 10 ASTRP_RCV 9 MFCO 8 MFCOM there are no further pending operations and gives up bus ownership. If TIMER is cleared, the Bus Activity Timer register is disabled and the PCnet-ISA II performs only one type of access (descriptor read, descriptor write, buffer read, or buffer write) and buffer accesses are performed to adjacent ascending addresses during each bus mastership period. TIMER is cleared by RESET. Disable Transmit Polling. If DPOLL is set, the Buffer Management Unit will disable transmit polling. Likewise, if DPOLL is cleared, automatic transmit polling is enabled. If DPOLL is set, TDMD bit in CSR0 must be periodically set in order to initiate a manual poll of a transmit descriptor. Transmit descriptor polling will not take place if TXON is reset. DPOLL is cleared by RESET. Auto Pad Transmit. When set, APAD_XMT enables the automatic padding feature. Transmit frames will be padded to extend them to 64 bytes, including FCS. The FCS is calculated for the entire frame (including pad) and appended after the pad field. APAD_XMT will override the programming of the DXMTFCS bit (CSR15.3). APAD_ XMT is reset by activation of the RESET pin. ASTRP_RCV enables the automatic pad stripping feature. The pad and FCS fields will be stripped from receive frames and not placed in the FIFO. ASTRP_ RCV is reset by activation of the RESET pin. Missed Frame Counter Overflow Interrupt. This bit indicates the MFC (CSR112) has overflowed. Can be cleared by writing a “1" to this bit. Also cleared by RESET or setting the STOP bit. Writing a “0" has no effect. Missed Frame Counter Overflow Mask. If MFCOM is set, MFCO will not set INTR in CSR0. 100 Am79C961A 7-6 5 RES RCVCCO 4 RCVCCOM 3 TXSTRT 2 TXSTRTM 1 JAB 0 JABM MFCOM is set by Reset and is not affected by STOP. Reserved locations. Read and written as zero. Receive Collision Counter Overflow. This bit indicates the Receive Collision Counter (CSR114) has overflowed. It can be cleared by writing a 1 to this bit. Also cleared by RESET or setting the STOP bit. Writing a 0 has no effect. Receive Collision Counter Overflow Mask. If RCVCCOM is set, RCVCCO will not set INTR in CSR0. RCVCCOM is set by RESET and is not affected by STOP. Transmit Start status is set whenever PCnet-ISA II controller begins transmission of a frame. When TXSTRT is set, IRQ is asserted if IENA = 1 and the mask bit TXSTRTM (CSR4.2) is clear. TXSTRT is set by the MAC Unit and cleared by writing a “1", setting RESET or setting the STOP bit. Writing a “0" has no effect. Transmit Start Mask. If TXSTRTM is set, the TXSTRT bit in CSR4 will be masked and will not set INTR flag in CSR0. TXSTRTM is set by RESET and is not affected by STOP. Jabber Error is set when the PCnet-ISA II controller Twisted-pair MAU function exceeds an allowed transmission limit. Jabber is set by the TMAU circuit and can only be asserted in 10BASE-T mode. When JAB is set, IRQ is asserted if IENA = 1 and the mask bit JABM (CSR4.4) is clear. The JAB bit can be reset even if the jabber condition is still present. JAB is set by the TMAU circuit and cleared by writing a “1". Writing a “0" has no effect. JAB is also cleared by RESET or setting the STOP bit. Jabber Error Mask. If JABM is set, the JAB bit in CSR4 will be masked and will not set INTR flag in CSR0. JABM is set by RESET and is not affected by STOP. CSR5: Control 1 Bit 0 Name SPND Description Suspend. Setting SPND to ONE will cause the PCnet-ISA II controller to start entering the suspend mode. The host must poll SPND until it reads a ONE back, to determine that the PCnet-ISA II controller has entered the suspend mode. Setting SPND to ZERO will get the PCnet-ISA II controller out of suspend mode and back into its active state. SPND can only be set to ONE if STOP (CSR0, bit 2) is set to ZERO. Asserting the RESET pin, reading the RESET register, or setting the STOP bit forces the PCnet-ISA II controller out of suspend mode. When the host requests the PCnet-ISA II controller to enter the suspend mode, the device first finishes all on-going transmit activity and updates the corresponding transmit descriptor entries. It then completes any frame reception occurring at the time the SPND bit was set, and updates the corresponding receive descriptor entries. Any subsequent frames incident upon the PCnet-ISA II during suspend mode will not be received, nor will any notification be given as to the missed frames (the MISS bit in CSR0 will not be updated while in suspend mode). It then sets the read-version of SPND to ONE and enters the suspend mode. In suspend mode, all of the CSR registers are accessible. As long as the PCnet-ISA II controller is not reset while in suspend mode (by asserting the RESET pin, reading the RESET register, or setting the STOP bit), no reinitialization of the device is required after the device comes out of suspend mode. The PCnet-ISA II controller will continue at the transmit and receive descriptor ring locations, where it had left, when it entered the suspend mode. Am79C961A 101 Read/Write accessible always. SPND is cleared by asserting the RESET pin, reading the RESET register, or setting the STOP bit 1 MP_MODE Magic Packet Mode. Setting this bit is a prerequisite for entering the Magic Packet mode. It also redefines the SLEEP pin to be a Magic Packet enable pin. Read/Write accessible always. It is cleared by asserting the RESET pin, or reading the RESET register. 2 MP_ENBL Magic Packet Enable. This bit when set, will force the PCnet-ISA II into the Magic Packet mode. Read/Write accessible always. It is cleared by asserting the RESET pin or reading the RESET register. 3 MP_I_ENBL Magic Packet Interrupt Enable. Acts as an unmask bit for the MP_INT (CSR5, bit 4). Read/ Write accessible always. It is cleared by asserting the RESET pin or reading the RESET register, or setting the STOP bit. 4 MP_INT Magic Packet Receive Interrupt. Will be set when a Magic Packet has been received. Writing a “one” will clear this bit. It is cleared by asserting the RESET pin, or reading the RESET register. CSR6: RCV/XMT Descriptor Table Length Bit 15-12 Name TLEN Description Contains a copy of the transmit encoded ring length (TLEN) field read from the initialization block during PCnet-ISA II controller initialization. This field is written during the PCnet-ISA II controller initialization routine. Read accessible only when STOP or SPND bits are set. Write operations have no effect and should not be performed. TLEN is only defined after initialization. Contains a copy of the receive encoded ring length (RLEN) read from the initialization block during PCnet-ISA II controller initialization. This field is written during the PCnet-ISA II controller initialization routine. Read accessible only when STOP or SPND bits are set. Write operations have no effect and should not be performed. RLEN is only defined after initialization. 7-0 RES Reserved locations. Read as zero. Write operations should not be performed. CSR8: Logical Address Filter, LADRF[15:0] Bit Name Description 15-0 LADRF[15:0] Logical Address Filter, LADRF [15:0]. Undefined until initialized either automatically by loading the initialization block or directly by an I/O write to this register. Read/write accessible only when STOP or SPND bits are set. CSR9: Logical Address Filter, LADRF[31:16] Bit Name Description 15-0 LADRF[31:16] Logical Address Filter, LADRF[31:16]. Undefined until initialized either automatically by loading the initialization block or directly by an I/O write to this register. Read/write accessible only when STOP or SPND bits are set. CSR10: Logical Address Filter, LADRF[47:32] Bit Name Description 15-0 LADRF[47:32] Logical Address Filter, LADRF[47:32]. Undefined until initialized either automatically by loading the initialization block or directly by an I/O write to this register. Read/write accessible only when STOP or SPND bits are set. CSR11: Logical Address Filter, LADRF[63:48] Bit Name Description 11-8 RLEN 15-0 LADRF[63:48] Logical Address Filter, LADRF[63:48]. Undefined until initialized either automatically by loading the initialization block or directly by an I/O write to this register. 102 Am79C961A Read/write accessible only when STOP or SPND bits are set. CSR12: Physical Address Register, PADR[15:0] Bit Name Description 15 PROM 15-0 PADR[15:0] Physical Address Register, PADR[15:0]. Undefined until initialized either automatically by loading the initialization block or directly by an I/O write to this register. The PADR bits are transmitted PADR[0] first and PADR[47] last. Read/write accessible only when STOP or SPND bits are set. CSR13: Physical Address Register, PADR[31:16] Bit Name Description 14 DRCVBC 15-0PADR[31:16] Physical Address Register, PADR[31:16]. Undefined until initialized either automatically by loading the initialization block or directly by an I/O write to this register. The PADR bits are transmitted PADR[0] first and PADR[47] last. Read/write accessible only when STOP or SPND bits are set. CSR14: Physical Address Register, PADR[47:32] Bit Name Description 13 DRCVPA 12 DLNKTST 15-0 PADR[47:32] Physical Address Register, PADR[47:32]. Undefined until initialized either automatically by loading the initialization block or directly by an I/O write to this register. The PADR bits are transmitted PADR[0] first and PADR[47] last. Read/write accessible only when STOP or SPND bits are set. CSR15: Mode Register Bit Name Description This register’s fields are loaded during the PCnet-ISA II controller initialization routine with the corresponding Initialization Block values. The register can also be loaded directly by an I/O write. 11 DAPC Activating the RESET pin clears all bits of CSR15 to zero. Promiscuous Mode. When PROM = “1", all incoming receive frames are accepted. Read/write accessible only when STOP or SPND bits are set. DisableReceiveBroadcast . When set, disables the PCnet-ISA II controller from receiving broadcast messages. Used for protocols that do not support broadcast addressing, except as a function of multicast. DRCVBC is cleared by activation of the RESET pin (broadcast messages will be received). Read/write accessible only when STOP or SPND bits are set. Disable Receive Physical Address. When set, the physical address detection (Station or node ID) of the PCnet-ISA II controller will be disabled. Frames addressed to the nodes individual physical address will not be recognized (although the frame may be accepted by the EADI mechanism). Read/write accessible only when STOP or SPND bits are set. Disable Link Status. When DLNKTST = “1", monitoring of Link Pulses is disabled. When DLNKTST = “0", monitoring of Link Pulses is enabled. This bit only has meaning when the 10BASE-T network interface is selected. Read/write accessible only when STOP or SPND bits are set. Disable Automatic Polarity Correction. When DAPC = “1", the 10BASE-T receive polarity reversal algorithm is disabled. Likewise, when DAPC = “0", the polarity reversal algorithm is enabled. This bit only has meaning when the 10BASE-T network interface is selected. Read/write accessible only when STOP or SPND bits are set. Am79C961A 103 10 MENDECL 9 LRT/TSEL LRT TSEL 8-7 PORTSEL [1:0] MENDEC Loopback Mode. See the description of the LOOP bit in CSR15. Read/write accessible only when STOP or SPND bits are set. Low Receive Threshold (T-MAU Mode only) Transmit Mode Select (AUI Mode only) Low Receive Threshold. When LRT = “1", the internal twisted pair receive thresholds are reduced by 4.5 dB below the standard 10BASE-T value (approximately 3/5) and the unsquelch threshold for the RXD circuit will be 180-312 mV peak. When LRT = “0", the unsquelch threshold for the RXD circuit will be the standard 10BASE-T value, 300-520 mV peak. In either case, the RXD circuit post squelch threshold will be one half of the unsquelch threshold. This bit only has meaning when the 10BASE-T network interface is selected. Read/write accessible only when STOP or SPND bits are set. Cleared by RESET. Transmit Mode Select. TSEL controls the levels at which the AUI drivers rest when the AUI transmit port is idle. When TSEL = 0, DO+ and DO- yield “zero” differential to operate transformer coupled loads (Ethernet 2 and 802.3). When TSEL = 1, the DO+ idles at a higher value with respect to DO-, yielding a logical HIGH state (Ethernet 1). This bit only has meaning when the AUI network interface is selected. Not available under Auto-Select Mode. Read/write accessible only when STOP or SPND bits are set. Cleared by RESET. Port Select bits allow for software controlled selection of the network medium. PORTSEL active only when Media-Select Bit set to 0 in ISACSR2. Read/write accessible only when STOP or SPND bits are set. Cleared by RESET. The network port configuration are as follows: PORTSEL[1:0] 00 01 10 11 Network Port AUI 10BASE-T GPSI* Reserved *Refer to the section on General Purpose Serial Interface for detailed information on accessing GPSI. 6 INTL 5 DRTY 4 FCOLL 3 DXMTFCS Internal Loopback. See the description of LOOP, CSR15.2. Read/write accessible only when STOP bit is set. Disable Retry. When DRTY = “1", PCnet-ISA II controller will attempt only one transmission. If DRTY = “0", PCnet-ISA II controller will attempt to transmit 16 times before signaling a retry error. Read/write accessible only when STOP or SPND bits are set. Force Collision. This bit allows the collision logic to be tested. PCnet-ISA II controller must be in internal loopback for FCOLL to be valid. If FCOLL = “1", a collision will be forced during loopback transmission attempts; a Retry Error will ultimately result. If FCOLL = “0", the Force Collision logic will be disabled. Read/write accessible only when STOP or SPND bits are set. Disable Transmit CRC (FCS). When DXMTFCS = “0", the transmitter will generate and append a FCS to the transmitted frame. When DXMTFCS = “1", the FCS logic is allocated to the receiver and no FCS is generated or sent with the transmitted frame. See also the ADD_FCS bit in TMD1. If DXMTFCS is set, no FCS will be generated. If both DXMTFCS is set and ADD_FCS is clear for a particular frame, no FCS will be generated. If ADD_FCS is set for a particular frame, the state of DXMTFCS is ignored and a FCS will be appended on that frame by the transmit circuitry. 104 Am79C961A 2 LOOP In loopback mode, this bit determines if the transmitter appends FCS or if the receiver checks the FCS. This bit was called DTCR in the LANCE (Am7990). Read/write accessible only when STOP or SPND bits are set. Loopback Enable allows PCnet-ISA II controller to operate in full duplex mode for test purposes. When LOOP = “1", loopback is enabled. In combination with INTL and MENDECL, various loopback modes are defined as follows. MENDECL X X 0 1 Loopback Mode Non-loopback External Loopback Internal Loopback Include MENDEC Internal Loopback Exclude MENDEC CSR16: Initialization Block Address Lower Bit 15-0 Name IADR Description Lower 16 bits of the address of the Initialization Block. Bit location 0 must be zero. This register is an alias of CSR1. Whenever this register is written, CSR1 is updated with CSR16’s contents. Read/Write accessible only when the STOP or SPND bits are set. Unaffected by RESET. CSR17: Initialization Block Address Upper Name RES Description Bit 15-8 LOOP 0 1 1 1 INTL X 0 1 1 1 DTX 0 DRX Read/write accessible only when STOP or SPND bits are set. LOOP is cleared by RESET. Disable Transmit. If this bit is set, the PCnet-ISA II controller will not access the Transmit Descriptor Ring and, therefore, no transmissions will occur. DTX = “0" will set TXON bit (CSR0.4) after STRT (CSR0.1) is asserted. DTX is defined after the initialization block is read. Read/write accessible only when STOP or SPND bits are set. Disable Receiver. If this bit is set, the PCnet-ISA II controller will not access the Receive Descriptor Ring and, therefore, all receive frame data are ignored. DRX = “0" will set RXON bit (CSR0.5) after STRT (CSR0.1) is asserted. DRX is defined after the initialization block is read. Read/write accessible only when STOP or SPND bits are set. Reserved locations. Written as zero and read as undefined. 7-0 IADR Upper 8 bits of the address of the Initialization Block. Bit locations 15-8 must be written with zeros. This register is an alias of CSR2. Whenever this register is written, CSR2 is updated with CSR17’s contents. Read/Write accessible only when the STOP or SPND bits are set. Unaffected by RESET. CSR18-19: Current Receive Buffer Address Bit 31-24 Name RES Description Reserved locations. Written as zero and read as undefined. 23-0 CRBA Contains the current receive buffer address to which the PCnet-ISA II controller will store incoming frame data. Read/write accessible only when STOP or SPND bits are set. CSR20-21: Current Transmit Buffer Address Bit 31-24 23-0 Name RES CXBA Description Reserved locations. Written as zero and read as undefined. Contains the current transmit buffer address from which the PCnet-ISA II controller is transmitting. Read/write accessible only when STOP or SPND bits are set. Am79C961A 105 CSR22-23: Next Receive Buffer Address Bit 31-24 Name RES Description Read/write accessible only when STOP or SPND bits are set. CSR32-33: Next Transmit Descriptor Address Bit 31-24 Name RES Description Reserved locations. Written as zero and read as undefined. 23-0 NRBA Contains the next receive buffer address to which the PCnet-ISA II controller will store incoming frame data. Read/write accessible only when STOP or SPND bits are set. CSR24-25: Base Address of Receive Ring Bit 31-24 Name RES Description Reserved locations. Written as zero and read as undefined. 23-0 NXDA Contains the next TDRE address pointer. Read/write accessible only when STOP or SPND bits are set. CSR34-35: Current Transmit Descriptor Address Bit Name RES Description Reserved locations. Written as zero and read as undefined. 23-0 BADR Contains the base address of the Receive Ring. Read/write accessible only when STOP or SPND bits are set. CSR26-27: Next Receive Descriptor Address Bit 31-24 Name RES Description 31-24 Reserved locations. Written as zero and read as undefined. 23-0 CXDA Contains the current TDRE address pointer. Read/write accessible only when STOP or SPND bits are set. CSR36-37: Next Next Receive Descriptor Address Bit Name NNRDA Description Reserved locations. Written as zero and read as undefined. 23-0 NRDA Contains the next RDRE address pointer. Read/write accessible only when STOP or SPND bits are set. CSR28-29: Current Receive Descriptor Address Bit 31-24 Name RES Description 31-0 Contains the next next RDRE address pointer. Read/write accessible only when STOP or SPND bits are set. CSR38-39: Next Next Transmit Descriptor Address Bit 31-0 Name NNXDA Description Reserved locations. Written as zero and read as undefined. 23-0 CRDA Contains the current RDRE address pointer. Read/write accessible only when STOP or SPND bits are set. CSR30-31: Base Address of Transmit Ring Bit 31-24 23-0 Name RES BADX Description Reserved locations. Written as zero and read as undefined. Contains the base address of the Transmit Ring. Contains the next next TDRE address pointer. Read/write accessible only when STOP or SPND bits are set. CSR40-41: Current Receive Status and Byte Count Bit Name Description Current Receive Status. This field is a copy of bits 15:8 of RMD1 of the current receive descriptor. Read/write accessible only when STOP or SPND bits are set. Reserved locations. Written as zero and read as undefined. 31-24 CRST 23-12 RES 106 Am79C961A 11-0 Current Receive Byte Count. This field is a copy of the BCNT field of RMD2 of the current receive descriptor. Read/write accessible only when STOP or SPND bits are set. CSR42-43: Current Transmit Status and Byte Count Bit Name Description CRBC CSR47: Polling Interval Bit 31-16 Name RES Description 31-24 CXST Current Transmit Status. This field is a copy of bits 15:8 of TMD1 of the current transmit descriptor. Read/write accessible only when STOP or SPND bits are set. 23-12 RES Reserved locations. Written as zero and read as undefined. 11-0 CXBC Current Transmit Byte Count. This field is a copy of the BCNT field of TMD2 of the current transmit descriptor. Read/write accessible only when STOP or SPND bits are set. CSR44-45: Next Receive Status and Byte Count Bit Name Description 31-24 NRST Next Receive Status. This field is a copy of bits 15:8 of RMD1 of the next receive descriptor. Read/write accessible only when STOP or SPND bits are set. 23-12 RES Reserved locations. Written as zero and read as undefined. 11-0 NRBC Next Receive Byte Count. This field is a copy of the BCNT field of RMD2 of the next receive descriptor. Read/write accessible only when STOP or SPND bits are set. CSR46: Poll Time Counter Bit 15-0 Name POLL Description Reserved locations. Written as zero and read as undefined. 15-0 POLLINT Polling Interval. This register contains the time that the PCnet-ISA II controller will wait between successive polling operations. The POLLINT value is expressed as the two’s complement of the desired interval, where each bit of POLLINT represents one-half of an XTAL1 period of time. POLLINT[3:0] are ignored. (POLINT[16] is implied to be a one, so POLLINT[15] is significant, and does not represent the sign of the two’s complement POLLINT value.) The default value of this register is 0000. This corresponds to a polling interval of 32,768 XTAL1 periods. The POLINT value of 0000 is created during the microcode initialization routine, and therefore might not be seen when reading CSR47 after RESET. If the user desires to program a value for POLLINT other than the default, then the correct procedure is to first set INIT only in CSR0. Then, when the initialization sequence is complete, the user must set STOP in CSR0. Then the user may write to CSR47 and then set STRT in CSR0. In this way, the default value of 0000 in CSR47 will be overwritten with the desired user value. Read/write accessible only when STOP or SPND bits are set. CSR48-49: Temporary Storage Bit 31-0 Name TMP0 Description Poll Time Counter. This counter is incriminated by the PCnet-ISA II controller microcode and is used to trigger the descriptor ring polling operation of the PCnet-ISA II controller. Read/write accessible only when STOP or SPND bits are set. Temporary Storage location. Read/write accessible only when STOP or SPND bits are set. CSR50-51: Temporary Storage Bit 31-0 Name TMP1 Description Temporary Storage location. Am79C961A 107 Read/write accessible only when STOP or SPND bits are set. CSR52-53: Temporary Storage Bit 31-0 Name TMP2 Description Temporary Storage location. Read/write accessible only when STOP or SPND bits are set. CSR54-55: Temporary Storage Bit 31-0 Name TMP3 Description Temporary Storage location. Read/write accessible only when STOP or SPND bits are set. CSR56-57: Temporary Storage Bit 31-0 Name TMP4 Description Read/write accessible only when STOP or SPND bits are set. 23-12 RES Reserved locations. Written as zero and read as undefined. Accessible only when STOP bit is set. 11-0 PXBC Previous Transmit Byte Count. This field is a copy of the BCNT field of TMD2 of the previous transmit descriptor. Read/write accessible only when STOP or SPND bits are set. CSR64-65: Next Transmit Buffer Address Bit 31-24 Name RES Description Temporary Storage location. Read/write accessible only when STOP or SPND bits are set. CSR58-59: Temporary Storage Bit 31-0 Name TMP5 Description Reserved locations. Written as zero and read as undefined. 23-0 NXBA Contains the next transmit buffer address from which the PCnet-ISA II controller will transmit an outgoing frame. Read/write accessible only when STOP or SPND bits are set. CSR66-67: Next Transmit Status and Byte Count Bit Name Description Next Transmit Status. This field is a copy of bits 15:8 of TMD1 of the next transmit descriptor. Read/write accessible only when STOP or SPND bits are set. Reserved locations. Written as zero and read as undefined. Accessible only when STOP bit is set. Next Transmit Byte Count. This field is a copy of the BCNT field of TMD2 of the next transmit descriptor. Read/write accessible only when STOP or SPND bits are set.CSR68-69: Transmit Status Temporary Storage Description Transmit Status Temporary Storage location. Read/write accessible only when STOP or SPND bits are set. Temporary Storage location. Read/write accessible only when STOP or SPND bits are set. CSR60-61: Previous Transmit Descriptor Address Bit 31-24 Name RES Description 31-24 NXST 23-12 RES Reserved locations. Written as zero and read as undefined. 23-0 PXDA Contains the previous TDRE address pointer. The PCnet-ISA II controller has the capability to stack multiple transmit frames. Read/write accessible only when STOP or SPND bits are set. CSR62-63: Previous Transmit Status and Byte Count Bit Name Description 11-0 NXBC Bit 31-0 Name XSTMP 31-24 PXST Previous Transmit Status. This field is a copy of bits 15:8 of TMD1 of the previous transmit descriptor. Am79C961A 108 CSR70-71: Temporary Storage Bit Name Description Read/write accessible only when STOP or SPND bits are set. CSR78: Transmit Ring Length Bit Name Description 31-0 Temporary Storage location. Read/write accessible only when STOP or SPND bits are set. CSR72: Receive Ring Counter Bit Name Description TMP8 Receive Ring Counter location. Contains a Two’s complement binary number used to number the current receive descriptor. This counter interprets the value in CSR76 as pointing to the first descriptor; a two’s complement value of -1 (FFFFh) corresponds to the last descriptor in the ring. Read/write accessible only when STOP or SPND bits are set. CSR74: Transmit Ring Counter Bit Name Description 15-0 RCVRC Transmit Ring Length. Contains the two’s complement of the transmit descriptor ring length. This register is initialized during the PCnet-ISA II controller initialization routine based on the value in the TLEN field of the initialization block. This register can be manually altered; the actual transmit ring length is defined by the current value in this register. Read/write accessible only when STOP or SPND bits are set. CSR80: Burst and FIFO Threshold Control Bit Name Description 15-0 XMTRL 15-14 RES 13-12RCVFW[1:0] Transmit Ring Counter location. Contains a Two’s complement binary number used to number the current transmit descriptor. This counter interprets the value in CSR78 as pointing to the first descriptor; a two’s complement value of -1 (FFFFh) corresponds to the last descriptor in the ring. Read/write accessible only when STOP or SPND bits are set. CSR76: Receive Ring Length Bit 15-0 Name RCVRL Description Receive Ring Length. Contains the Two’s complement of the receive descriptor ring length. This register is initialized during the PCnet-ISA II controller initialization routine based on the value in the RLEN field of the initialization block. This register can be manually altered; the actual receive ring length is defined by the current value in this register. 15-0 XMTRC Reserved locations. Read as ones. Written as zero. Receive FIFO Watermark. RCVFW controls the point at which ISA bus receive DMA is requested in relation to the number of received bytes in the receive FIFO. RCVFW specifies the number of bytes which must be present (once the frame has been verified as a non-runt) before receive DMA is requested. Note however that, if the network interface is operating in half-duplex mode, in order for receive DMA to be performed for a new frame, at least 64 bytes must have been received. This effectively avoids having to react to receive frames which are runts or suffer a collision during the slot time (512 bit times). If the Runt Packet Accept feature is enabled, receive DMA will be requested as soon as either the RCVFW threshold is reached, or a complete valid receive frame is detected (regardless of length). RCVFW is set to a value of 10b (64 bytes) after RESET. Read/write accessible only when STOP or SPND bits are set. Am79C961A 109 . RCVFW[1:0] 00 01 10 11 Bytes Received 16 32 64 Reserved XMTFW[1:0] 10 11 Write Cycles 32 Reserved 7-0 11-10XMTSP[1:0]Transmit Start Point. XMTSP controls the point at which preamble transmission attempts commence in relation to the number of bytes written to the transmit FIFO for the current transmit frame. When the entire frame is in the FIFO, transmission will start regardless of the value in XMTSP. XMTSP is given a value of 10b (64 bytes) after RESET. Regardless of XMTSP, the FIFO will not internally over-write its data until at least 64 bytes (or the entire frame if