ACD0900S3CTR

ACD0900 VHF/UHF CATV/TV Tuner Downconverter Data Sheet - Rev 2.2 FEATURES • • • • • • • • Integrated Monolithic Downconverter 8 dB Noise Figure 10 dB Conversion Gain High Linearity Small Size Low Cost High Reliability RoHS-Compliant Package Option S3 Package Modified 16 Pin SOIC PRODUCT DESCRIPTION The ACD0900 MMIC is a high performance downconverter fabricated entirely in GaAs. It is designed for use as the second conversion stage in double-conversion tuners and cable modems, downconverting 900 -1200 MHz RF inputs to a fixed IF of 35 - 150 MHz (depending on LO frequency). The IC incorporates a low noise amplifier, high linearity double balanced mixer, phase splitter and oscillator in a modified SOIC 16 lead surface mount package. The high degree of functionality allows tuner manufactures to reduce size and cost by lowering the component count and decreasing the amount of production alignment steps, while significantly improving performance and reliability. IF1,+5V 1 MXR 15 16 IF2, + 5V GND GND 2 14 OSCOUT N/C 3 PHASE SPLITTER 4 13 GND 12 GND 5 OSC 11 TCKT RFIN 6 LOW NOISE AMP. ISET 10 7 +5V GND 8 9 N/C Figure 1: Functional Block Diagram 05/2005 ACD0900 Table 1: Pin Description PIN 1 2 3 4 5 6 7 8 DESCRIPTION IF1, VDDIF GND NC GND GND RFIN ISET GND PIN 9 10 11 12 13 14 15 16 DESCRIPTION NC* V D D LO TCKT GND GND OSC OUT GND IF2, VDDIF * Do not connect pin 9 to GND 2 Data Sheet - Rev 2.2 05/2005 ACD0900 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER VDDIF, VDDLO, VOSC VRF, VTCKT (1) Storage Temperature Soldering Temperature Soldering Time RF Input Power LO Input Power Thermal Resistance MIN - 55 MAX 9 0 200 260 5 + 10 + 17 25 UNIT Volts Volts °C °C S e c. dB m dB m °C/W Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Note: (1) VTCKT : Maximum voltage that may be applied to pin 11 of the device without damaging the IC. DC blocking capacitor (1500 pF) between pin 11 and the external tuning circuit is mandatory. Table 3: Operating Ranges PARAMETER Frequency RF LO IF VDDIF, VDDLO Case Temperature 900 935 35 4.75 - 55 5.0 1200 1350 150 5.25 85 MHz VD C °C MIN TYP MAX UNIT The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Data Sheet - Rev 2.2 05/2005 3 ACD0900 Table 4: Electrical Specifications ( TA = +25°C; V , V = +5V) DDIF DDLO PARAMETER Frequencies RF LO IF Phase Noise @ 10 KHz Offset Noise Figure Gain ( 200 Ω Load)(1) 3rd Order IMD (200 Ω Load)(2) 3rd Order Input IP ( 200Ω Load)(2) Cross Modulation @ 15 KHz, (2) 99% AM Modulation Current Consumption Power Consumption @ 5.0V MIN 7.8 + 12 - TYP 1170 1245 75 - 89 8.0 9.5 - 59 - 56 80 400 MAX - 85.5 9.5 - 54 110 - UNIT COMMENTS MHz dBc/Hz dB dB dB c dB m dB c mA mW Notes: (1) Combined output ( IF1 + IF2) using a balun. NOTE: Gain at either port (uncombined), with unused port terminated in 50 W, is 3 dB lower (2) Two tones @ -15 dBm per tone 4 Data Sheet - Rev 2.2 05/2005 ACD0900 IFOUT N:1 +5V 0.01 µF IF1 1 16 IF2 MIXER 2 15 NC 3 PHASE SPLITTER 14 0.001 µF OSC Output to Prescalar 4 13 5 12 3.3 pF OSC 0.01 µF 2 KΩ 12 K Ω 0.1 µF RFIN 6 0.001 µF 7 5.6 Ω 8 LOW NOISE AMP 11 1SV245 10 100 pF 9 NC L 330 µF Vtune +5V Figure 2: Test Circuit Schematic Data Sheet - Rev 2.2 05/2005 5 ACD0900 PERFORMANCE DATA Figure 3: RF Input Impedance START:50MHz STOP: 2000MHz 1 .5 2 1: 50 MHz 183.00Ω - 21.75 jΩ 250 MHz 135.48Ω -58.21 jΩ 2: .2 5 0 3: .2 .5 5 1 4 3 -5 2 5 2 1 750 MHz 75.92Ω - 43.12 jΩ 1000 MHz 64.93Ω - 32.29 jΩ 2000 MHz 43.79Ω -4.71 jΩ -.2 4: -.5 -.1 -2 5: MEASURED IN 50Ω SYSTEM IMPEDANCE REFERENCE PLANE AT PIN 6 Figure 4: IF Output Impedance START: 50 MHz STOP: 500 MHz 1 .5 2 1: 50 MHz 251.64Ω - 222.35 jΩ 150 MHz 60.89Ω -144.22 jΩ 2: .2 5 3: 0 .2 .5 1 2 5 1 -.2 3 5 -.5 -1 4 -2 2 250 MHz 26.32Ω - 89.16 jΩ 400 MHz 13.24Ω - 49.55 jΩ 500 MHz 10.08Ω - 34.10 jΩ 4: -5 5: MEASURED IN 50Ω SYSTEM IMPEDANCE REFERENCE PLANE AT PIN 16 6 Data Sheet - Rev 2.2 05/2005 ACD0900 Figure 5: LO Impedance START: 50 MHz STOP: 2000 MHz .5 1 1: 50 MHz 259.67Ω - 1200 jΩ 612 MHz - 20.97Ω - 50.63 jΩ 2: 2 .2 5 5 4 -.17 1 3 -5 -5.8 3: 1000 MHz - 9.28Ω - 14.88 jΩ 1500 MHz - 5.36Ω 7.99 jΩ 2000 MHz 0.64Ω 27.12 jΩ 4: 2 -.2 -2 5: -.5 -1 MEASURED IN 50Ω SYSTEM IMPEDANCE REFERENCE PLANE AT PIN 11 Data Sheet - Rev 2.2 05/2005 7 ACD0900 PACKAGE OUTLINE Figure 6: S3 Package Outline - Modified 16 Pin SOIC 8 Data Sheet - Rev 2.2 05/2005 ACD0900 NOTES Data Sheet - Rev 2.2 05/2005 9 ACD0900 NOTES 10 Data Sheet - Rev 2.2 05/2005 ACD0900 NOTES Data Sheet - Rev 2.2 05/2005 11 ACD0900 ORDERING INFORMATION ORDER NUMBER ACD0900S3CTR ACD0900RS3P1 TEMPERATURE RANGE -55°C to +85°C -55°C to +85°C PACKAGE DESCRIPTION Modified 16 Pin SOIC RoHS Compliant Modified 16 Pin SOIC COMPONENT PACKAGING Tape & Reel, 3500 pieces per reel Tape & Reel, 3500 pieces per reel ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 12 Data Sheet - Rev 2.2 05/2005