AMT8650-H1

AMT8650 10 Gb/s 1310/1550nm PIN-TIA ADVANCED PRODUCT INFORMATION – Rev 0.0 FEATURES • • • • • • 10 Gb/s differential output TIA 8.5 GHz Bandwidth -19 dBm Typical Sensitivity +3 dBm Optical Overload 1250-1620nm PIN Photodetector Transimpedance gain of 10K and 600mVpp output APPLICATIONS • • SONET OC-192/SDH STM-64 10Gb/s Ethernet High speed 5-pin package Product Description The ANADIGICS AMT8650 is a low cost optical receiver capable of operation to 10Gb/s. A high performance PIN photodiode and a low noise, high gain transimpedance pre-amplifier (TIA) are incorporated in a hermetic, high speed header. The bandwidth is 8.5Ghz and dynamic range is over 22dB. High gain of the TIA eliminates the need for a separate post amplifier in most applications. These devices are readily designed into receivers, transceivers and transponders for SONET OC192/SDH STM-64 and 10 Gigabit Ethernet. VPD 2 VTIA 3 RF PIN 1 VOUTP VOUTN 4 Vref 5 Figure 1: Functional Block Diagram 01/2006 AMT8650 ELECTRICAL CHARACTERISTICS Table 1: Absolute Maximum Ratings PARAMETER Supply Voltage Photodiode bias Voltage Optical Input Power Storage Temperature MIN -0.5 2.5 - 40 MAX 5.5 10 +4 + 85 UNIT V V dBm oC Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 2: Electrical Specifications PARAMETER Wavelength (1) Sensitivity Overload Responsivity 1550nm Responsivity 1310nm Dark current Small signal transimpedance gain (differential) Small signal 3dB bandwidth Low frequency cutoff Output return loss (differential)(2) Output voltage swing (differential) Optical return loss Photodiode bias voltage TIA supply voltage TIA supply current Power consumption Operating temperature (1) (2) 10Gb/s PRBS 2 -, 1550nm, ER >12dB ½(S11 - S21 + S22 - S12), 100MHz – 9GHz 31 MIN 1250 0.80 0.75 50 4 4.7 -40 TYP -19 3 0.90 0.85 0.2 10 8.5 30 9 600 55 5 5 48 240 25 MAX 1620 5 9 5.3 85 UNIT nm dB dBm A/W A/W nA KΩ GHz KHz dB mVP-P dB V V mA mW oC Figure 2: Pin location 2 3 PIN 1 2 3 4 5 NAME VOUTP VPD VTIA VOUTN Ground Table 3: Pin description DESCRIPTION Non-inverted output voltage. Logical ‘1’ with an optical input. Output is not AC coupled. Photodiode bias: 5V Amplifier supply voltage: 5V Inverted output voltage: Logical ‘0’ with an optical input. Output is not AC coupled Ground 1 4 5 ADVANCED PRODUCT INFORMATION – Rev 0.0 01/2006 2 AMT8650 PERFORMANCE 12 10 8 6 4 dB 2 0 -2 -4 -6 0 1 2 3 4 5 6 GHz 7 8 9 10 11 12 Figure 3: Frequency response of AMT8650-T46L-EVA (-20dBm optical input) Figure 4: Optical input power: –5dBm, extinction ratio: 12dB. (100mV/Div, 20ps/Div) Figure 5: Optical input power: –10dBm, extinction ratio: 12dB. (100mV/Div, 20ps/Div) Figure 6: Optical input power: –15dBm, extinction ratio: 12dB. (50mV/Div, 20ps/Div) Figure 7: Optical input power: –20dBm, extinction ratio: 12dB. (20mV/Div, 20ps/Div) ADVANCED PRODUCT INFORMATION – Rev 0.0 01/2006 3 AMT8650 PACKAGE DIMENSIONS (mm [Inches]) 3.18 [0.1251] 4.71 [0.1857] 1.32 [0.0520] 1.17 [0.0461] 4x R0.23 [R0.0089] R0.12 [R0.0049] R0.23 [R0.0089] 0.89 [0.0351] 5.41 [0.2132] 4.76 [0.1875] 1.23 [0.0485] 0.56 [0.0219] 3.66 [0.1440] 0.38 [0.0150] 2.54 [0.1001] EVALUATION BOARD VTIA 180nH 22uF/20V GND GND 100nF GND 10nF RF out (P) V TIA V PD VPD 180nH 330R 22uF/20V 100nF GND GND 10nF GND 10nF 100nF GND VOUTP VOUTN GND 100nF RF out (N) GND GND ORDERING INFORMATION Part Number AMT8650-T46L AMT8650-H1 AMT8650-T46L-EVA AMT8650-H1-EVA PACKAGE DESCRIPTION 5V High speed 5 pin package with ball lens 5V High speed 5 pin package with SC/APC pigtail 5V High speed 5 pin package with ball lens mounted on evaluation board 5V High speed 5 pin package with pigtail mounted on evaluation board ANADIGICS, Inc. 829 Flynn Road Camarillo, California 93012, U.S.A. Tel: +1 (805) 445-4500 Fax: +1 (805) 445-4502 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibility for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices, or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. ADVANCED PRODUCT INFORMATION – Rev 0.0 01/2006 4