AWL6254RS35P8

2.4 GHz 802.11b/g/n WLAN PA, LNA, and RF Switch Data Sheet - Rev 2.0 AWL6254 FEATURES • 3.3 % EVM @ POUT = +16 dBm with IEEE 802.11g 64 QAM OFDM at 54 Mbps • 75 mA Transmit Path Current Consumption at POUT = +16 dBm • SP3T RF Switch to Enable Bluetooth Path • Single +3.6 V Supply • Transmit Path Linear Power Gain of 28 dB • Temperature-Compensated Linear Power Detector with Positive Slope • Receive Path In-Band Gain of 13 dB • Receive Path Noise Figure of 2.3 dB • 3 mm x 3 mm x 0.55 mm ULPCC Package AW L6 254 APPLICATIONS • 802.11b/g WLAN in Cell Phone Designs • 802.11n in WLAN MIMO Systems • 2.4 GHz Cordless Phone Handsets/Basestations S35 Package 16 Pin 3 mm x 3 mm x 0.55 mm Surface Mount ULPCC PRODUCT DESCRIPTION The antenna port is switched between WLAN transmit, WLAN receive, and Bluetooth paths with a low-loss single-pole triple-throw RF switch. The transmit path PA exhibits unparalleled linearity for both IEEE 802.11b/g/n WLAN systems under the toughest signal configurations within these standards. The WLAN receive path from the antenna port to receiver output port provides a low noise, high-gain path to the system receiver chain. The positive slope power detector is temperaturecompensated on the chip, enabling a single-ended output voltage with excellent accuracy over a wide range of operating temperatures. The AWL6254 is biased by a single +3.6 V supply and consumes ultralow current in the OFF mode. 02/2008 Bias Network Output Match Rx RFOUT WLAN Rx Enable BLUETOOTH Enable WLAN Tx Enable Tx RFIN BLUETOOTH GND The ANADIGICS AWL6254 is a high performance InGaP HBT power amplifier, low-noise amplifier, and RF switch integrated on a single IC. It is particularly applicable to cell phone designs that integrate 802.11b/g WLAN in the 2.4 - 2.5 GHz band. Matched to 50  on all RF ports, the part requires no additional RF matching components off-chip. The AWL6254 is manufactured using advanced InGaP HBT technology that offers state-of-the-art reliability, temperature stability and ruggedness. It is provided in a 3 mm x 3 mm x 0.55 mm ULPCC package optimized for a 50  system. VCC Antenna Control Logic Input Match Output Match Power Detector Bias Network Figure 1: Block Diagram and Pinout DET_OUT GND VCC AWL6254 Table 1: Pin Description PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 NAME DESCRIPTION BLUETOOTH Bluetooth RF Port GND RX_RF GND LNA_EN BT_EN PA_EN GND PA_IN GND NC VCC DET_OUT GND ANT GND Ground Receive RF Port Ground LNA Enable. On/Off control for the Rx path low noise amplifier Bluetooth Enable. On/Off control for the Bluetooth path Power Amplifier Enable. On/Off control for the Tx path power amplfier Ground Power Amplfier Input Ground No Connection Power Supply. Bias for the transistors in the part Power Detector Output. DC coupled power detector output. An emitter follower BJT supplies the output for this pin. Ground Antenna Port. Common connection for the PA, LNA, and Bluetooth paths Ground 2 Data Sheet - Rev 2.0 02/2008 AWL6254 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER DC Power Supply Voltage (VCC) DC Power Control Voltage (VPA_EN) DC Power Control Voltage (VLNA_EN) DC Power Control Voltage (VBT_EN) DC Current Consumption Tx RF Input Level (RFIN) Ant RF Input Level (RFIN) Bluetooth RF Input Level (RFIN) Storage Case Temperature Operating Case Temperature ESD Tolerance MSL Rating Reflow Temperature MIN -55 -40 500 MAX +5.0 +5.0 +5.0 +5.0 300 0 -3 23 +150 +85 MSL-2 260 °C UNIT V V V V mA dBm dBm dBm °C °C VDC All pins, forward and reverse voltage. Human Body Model (HBM) COMMENTS No RF Signal Applied No RF Signal Applied No RF Signal Applied No RF Signal Applied Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER Operating Frequency (f) DC Power Supply Voltage (VCC) Control Voltage (VPA_EN, VLNA_EN, VBT_EN) Case Temperature (TC) Control Pin Impedance (VPA_EN, VLNA_EN, VBT_EN) MIN 2400 +3.3 +2.0 0 -40 TYP +3.6 +3.3 720 MAX 2500 +4.2 +4.2 +0.4 +85 UNIT MHz V V °C k PA "ON" PA "SHUTDOWN" COMMENTS The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Data Sheet - Rev 2.0 02/2008 3 AWL6254 Table 4: DC Electrical Specifications - Tx Path Continuous Wave (TC = +25 °C, VCC = +3.6 V, VPA_EN = +3.3 V, VLNA_EN = 0 V , VBT_EN = 0 V) PARAMETER P1dB Current at P1dB Shutdown Current Quiescent Current Harmonics 2fo 3fo Input Return Loss, Tx RFIN Output Return Loss, Antenna Port, Switch in Transmit Mode Reverse Isolation (Antenna Port to Tx Input Port) Stability (Spurious) TON Settling Time MIN 20 140 18 TYP 22 175 25 26 MAX 210 75 34 UNIT dBm mA A mA Shutdown Mode VCC = +3.6 V, VPA_EN = +3.3 V, VLNA_EN = 0 V, VBT_EN = 0 V, RF = off COMMENTS - -48 -68 -7 -40 -60 -3 dBc dB POUT=+18 dBm (1) - -9 -4 dB Switch in Tx Position Switch in Tx Position, signal injected into Antenna port and measured at Tx input port, PA = "ON" 6:1 VSWR, POUT = +18 dBm(1), -40 OC 10% to 90% of maximum RF power. POUT = +16 dBm(1) 30 - 40 -60 1.0 -50 2.0 dB dBc s Note: (1) Power as measured at Antenna port of AWL6254. 4 Data Sheet - Rev 2.0 02/2008 AWL6254 Table 5: Electrical Specifications - Tx Path 802.11g (TC = +25 °C, VCC = +3.6 V, VPA_EN = +3.3 V, VLNA_EN = 0 V , VBT_EN = 0 V, 64 QAM OFDM 54 Mbps) PARAMETER Operating Frequency Power Gain Gain Ripple Error Vector Magnitude (EVM) Tx Spectrum Mask Current Consumption Power Detector Voltage Power Detector Sensitivity MIN 2400 25 Pass 60 650 50 TYP 28 1.5 3.3 -29.6 75 780 68 MAX 2500 32 2.0 5.0 -26 95 900 85 UNIT MHz dB dB % dB N/A mA mV Across 100 MHz band POUT = +16 dBm (1), (2) POUT = +16 dBm (2) POUT = +16 dBm (2) POUT = +16 dBm (2) COMMENTS mV/dB 10 dBm < POUT < +17 dBm (2) Note: (1) EVM includes system noise floor of 1% (-40 dB). (2) Power as measured at Antenna port of AWL6254 Table 6: Electrical Specifications - Tx Path 802.11b (TC = +25 °C, VCC = +3.6 V, VPA_EN = +3.3 V, VLNA_EN = 0 V , VBT_EN = 0 V, 1 Mbps, Gaussian Filtering, bT=0.50) PARAMETER Operating Frequency Power Gain Gain Ripple Adjacent Channel Power (ACPR) 1st Sidelobe (11 - 22 MHz Offset) Adjacent Channel Power (ACPR) 2nd Sidelobe (>22 MHz Offset) Tx Spectrum Mask Current Consumption Power Detector Voltage Power Detector Sensitivity MIN 2400 25 Pass 75 810 60 TYP 28 1.5 -33 -53 100 970 78 MAX 2500 32 2.0 -30 -50 125 1115 95 UNIT MHz dB dB dBr dBr N/A mA mV Across 100 MHz band POUT = +18 dBm (1) POUT = +18 dBm (1) POUT = +18 dBm (1) POUT = +18 dBm (1) POUT = +18 dBm (1) COMMENTS mV/dB 10 dBm < POUT < +20 dBm (1) Note: (1) Power as measured at Antenna port of AWL6254 Data Sheet - Rev 2.0 02/2008 5 AWL6254 Table 7: DC Electrical Specifications - Rx Path Continuous Wave (TC = +25 °C, VCC = +3.6 V, VPA_EN = 0 V, VLNA_EN = +3.3 V , VBT_EN = 0 V) PARAMETER Power Gain Gain Ripple P1dB Current at P1dB Quiescent Current Noise Figure Return Loss, Rx RF Port Return Loss, Antenna Port, Switch in Receive Mode Isolation (Antenna Port to Rx Port) S21 Performance (@ 1.9 GHz) Stability MIN 10 4 9 9 TYP 13 0.5 6 13 13 2.3 -12 MAX 16 1.0 17 17 3.9 -8 UNIT dB dB dBm mA mA dB dB Includes RF switch and LNA Switch in Rx position, Antenna port terminated in 50  load Switch in Rx position, with 50  Rx port load Switch in Tx position, signal injected into Antenna port and measured at Rx port, PA = "ON" Across 100 MHz Band COMMENTS - -7 -3 dB 22 29 - dB - -6 -60 0 -50 dB dBc 6 Data Sheet - Rev 2.0 02/2008 AWL6254 Table 8: DC Electrical Specifications - Bluetooth Path Continuous Wave (TC = +25 °C, VCC = +3.6 V, VPA_EN = 0 V, VLNA_EN = 0 V , VBT_EN = +3.3 V) PARAMETER Insertion Loss Quiescent Current P1dB Return Loss, Bluetooth RF Port Return Loss, Antenna Port, Switch in Bluetooth Mode Isolation (Antenna Port to Rx Port) MIN 20 TYP 0.8 60 25 -10 MAX 1.5 125 -8 UNIT dB A dBm dB Switch in Bluetooth position, Antenna port terminated in 50  load Switch in Bluetooth position, Bluetooth port terminated in 50  load Switch in Bluetooth position, signal injected into Antenna port and measured at Rx port COMMENTS 2.4 GHz to 2.5 GHz - -10 -8 dB 30 38 - dB Table 9: Control Logic Truth Table FEIC MODE Shutdown WLAN Rx Bluetooth WLAN Tx PA ENABLE 0 0 0 1 BLUETOOTH ENABLE 0 0 1 0 LNA ENABLE 0 1 0 0 PA STATUS Off Off Off On LNA STATUS Off On Off Off SWITCH STATUS Not Connected WLAN Rx Bluetooth WLAN Tx Note: 1. Logic State 0 = 0 - 0.4 V; Logic State 1 = 2.0 - 4.2 V Table 10: Control Voltages and Timing (TC = +25 °C, VCC = +3.6 V, Other Voltages Defined by Logic Below) PARAMETER LNA Enable Pin Control Voltage Bluetooth Enable Pin Control Voltage PA Enable Pin Control Voltage MIN +2.0 +2.0 +2.0 TYP MAX +0.4 +0.4 +0.4 UNIT V V V COMMENTS LNA = 1 LNA = 0 Switch = 1 Switch = 0 PA = 1 PA = 0 Note: 1. Logic State 0 = 0 - 0.4 V; Logic State 1 = 2.0 - 4.2 V Data Sheet - Rev 2.0 02/2008 7 AWL6254 PERFORMANCE DATA Figure 2: Tx Path Gain and Icc vs. Output Power o AcrossTxFreq (VCC vs. Output Power Across FrequencyC) Figure 2: Path Gain and Icc = +3.6 V, TA = +25 Vcc = +3.6 V, T = +25 C 802.11g 54 Mbps OFDM 802.11g 54 Mbps OFDM 32 30 28 26 24 22 20 320 300 280 260 240 220 34 32 30 28 26 24 22 Figure 3: Path Gain and ICC vs. Output Power Across Temp Gain and Icc= 2.45 Power Across CC = +3.6 V) (Freq vs. Output GHz, V Temperature Figure 3: Tx Path Frequency 2.45 Mbps = +3.6 V 802.11g= 54 GHz, VoltageOFDM 802.11g 54 Mbps OFDM 340 320 300 280 260 Gain Gain Gain -40C Current -40C Gain +25C Current +25C Gain +85C Current +85C 240 220 200 180 160 140 120 100 80 60 Gain (dB) 18 16 14 12 10 8 6 4 2 0 0 1 180 160 140 120 100 80 60 Gain (dB) Current 2.40 GHz Current 2.45 GHz Current 2.50 GHz Current (mA) 20 18 16 14 12 10 8 6 4 2 0 0 1 Current 40 20 0 Current 40 20 0 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Output Power (dBm) Output Power (dBm) Figure 4: Tx Path Gain and ICC vs. Output Power Across4:Powern SupplyutVoltage (Freq upply VoltageGHz, Figure Tx Path Gai and Icc vs. O put Power Across Power S = 2.45 Freq = 2.45 GHz, T = +25 C TA = +25oC)802.11g 54 Mbps OFDM Mbps OFDM 802.11g 54 32 30 28 26 24 22 20 320 300 280 Figure 5: Tx Path EVM vs. Output Power Across o igure 5: x ath EVM V, ut A P +25 C) 802.11g FreqF(VCC T=P+3.6 vs. OTput=ower Across Frequency Vcc = +3.6 V, T = +25 C 54802.11g 54 Mbps OFDM Mbps OFDM 10 9 8 7 Gain 260 240 EVM 2.40 GHz EVM 2.45 GHz EVM 2.50 GHz Gain 3.3V Icc 3.3V Gain 3.6V Icc 3.6V Gain 4.2V Icc 4.2V 220 Gain (dB) 16 14 12 10 8 6 4 2 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 160 140 120 100 80 60 EVM (%) 18 180 Current (mA) 200 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Current 40 20 0 Output Power (dBm) Output Power (dBm) Figure 6: Tx Path EVM vs. Output Power Across Temp (Freq = 2.45 GHz, VCC = +3.6 V) 802.11g 54 Mbps OFDM 10 9 8 7 6 Figure 7: Tx Path EVM vs. Output Power Across Power Tx Path EVM vs. Output Power (Freq = Supply Voltage Supply Voltage Across Power 2.45 GHz, Figure 7: 802.11g = +25 C TA = +25oC)Freq = 2.45 GHz, T54 Mbps OFDM 802.11g 54 Mbps OFDM 10 9 8 7 6 5 4 3 2 1 0 EVM -40C EVM +25C EVM +85C EVM 3.3V EVM 3.6V EVM 4.2V EVM (%) 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 EVM (%) 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Output Power (dBm) Output Power (dBm) 8 Data Sheet - Rev 2.0 02/2008 Current (mA) 20 Gain 2.40 GHz Gain 2.45 GHz Gain 2.50 GHz 200 AWL6254 Figure 8: Tx Path Detector Voltage vs. Output Power: Tx Path Detector Voltage (TOut= t +ower oC, Vrequency+3.6 V) Figure 8 Across Freq vs. A pu P 25 Across F CC = Vcc = +3.6 V, = +25 C 802.11g5454T Mbps OFDM 802.11g Mbps OFDM 1.2 1.1 1.0 0.9 Figure 9: Tx Path Detector Voltage vs. Output Power Across Temp (Freq = 2.45 GHz, VCC = +3.6 V) Figure 9: Tx Path Detector Voltage vs. Output Power Across Temperature Frequency = 2.45 GHz, Voltage = +3.6OFDM 802.11g 54 Mbps V 802.11g 54 Mbps OFDM 1.2 1.1 1.0 0.9 Det. Volt. 2.40GHz Det. Volt. 2.45GHz Detector Voltage (V) Det. Volt. -40C Det. Volt. +25C Det. Volt.+85C Detector Voltage (V) 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0 1 2 Det. Volt. 2.50GHz 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Output Power (dBm) Output Power (dBm) Figure 10: Tx Path Detector Voltage vs. Output Power Across Supply Voltage (Freq = 2.45 GHz, Voltage = TA = +25OFreq =802.11g +25 C Mbps OFDM C) 2.45 GHz, T OFDM 54 802.11g 54 Mbps 1.2 1.1 1.0 0.9 Figure 11: Tx Path and ICC vs. Output Power Across Path Gain and Icc = +25oC ,VCC Frequency V) Figure 11: Tx Freq (TA vs. Output Power Across = +3.6 Vcc = +25 802.11b Gaussian +3.6 V, T =(bT =C (bT=0.5), 1 Mbps 802.11b Gaussian Filtering 1 Mbps Filtering 0.5), 32 30 28 320 300 280 26 24 22 20 Det. Volt. 3.3V Det. Volt. 3.6V Det. Volt. 4.2V Gain (dB) Gain 260 240 220 Detector Voltage (V) 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 18 16 14 12 10 8 6 4 2 0 0 1 Current 2.40 GHz Current 2.45 GHz Current 2.50 GHz 180 160 140 120 100 80 Current 60 40 20 0 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Output Power (dBm) Output Power (dBm) Figure 13: Tx Path Gain and Icc vs. Output Power Figure 12: Tx Path Gain and ICC vs. Output Power Supply Voltage Power Across Power Supply TA Across Temp (Freq =and Icc vs.GHz, VCC = +3.6 V) 802.11b Across Tx Path Gain and Icc vs. Output(Freq=2.45 GHz,Voltage= +25oC) 2.45 Output Power Across Temperature Figure 13: Figure 12: Tx Path Gain Frequency = 2.45 GHz, Voltage = +3.6 V Freq = 2.45 Filtering = C 802.11b Gaussian GHz, T(bT+250.5), 1(bT=0.5), 1 Mbps Gaussian Filtering (bT=0.5),bps Mbps 1 802.11b Gaussian Filtering (bT = 0.5), 1 M 802.11b Gaussian Filtering = Mbps 34 32 30 28 26 24 22 340 320 300 280 260 32 30 28 26 24 22 320 300 280 Gain 260 240 220 Gain 240 220 Gain (dB) Gain (dB) 20 18 16 14 12 10 8 6 4 2 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 200 Current (mA) 20 18 16 14 12 10 8 6 4 2 0 0 1 Gain 3.3V Icc 3.3V Gain 3.6V Icc 3.6V Gain 4.2V Icc 4.2V 200 180 160 140 120 100 80 Gain -40C Current -40C Gain +25C Current +25C Gain +85C Current +85C 180 160 140 120 100 80 Current 60 40 20 0 Current 60 40 20 0 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Output Power (dBm) Output Power (dBm) Data Sheet - Rev 2.0 02/2008 Current (mA) 0.8 Gain 2.40 GHz Gain 2.45 GHz Gain 2.50 GHz 200 9 AWL6254 Figure 14: Tx Path ACPR Sidelobes 1 & 2 vs. Figure 15: Tx Path ACPR Sidelobes 1 & 2 vs. Output Figure 4: Tx Path A nd idelobes Output 1Power CPR 1st &F2requency vs. Output=ower Across TA = Across SFreq (Vcc P +3.6 V, emperature Power Across Temp T(Freq = 2.45 GHz, VCC = +3.6 V) Frequency = 2.45 GHz, Voltage = +3.6 V Vcc = +3.6 T = +25 C +25oC) 802.11b GaussianV,FilteringM(bT=0.5), 1 Mbps 802.11b GaussianFiltering (bT = 0.5), (bT=0.5), 1 Mbps 802.11b Gaussian Filtering 1 Mbps 802.11b Gaussian Filtering (bT = 0.5), 1 bps -22 -26 -30 -34 -22 -26 -30 -34 ACPR Sidelobe (dBr) -42 -46 -50 -54 -58 -62 -66 0 1 1st Sidelobe 2.40GHz 1st Sidelobe 2.45GHz 1st Sidelobe 2.50GHz 2nd Sidelobe 2.40GHz 2nd Sidelobe 2.45GHz 2nd Sidelobe 2.50GHz ACPR Sidelobe (dBr) -38 -38 -42 1st Sidelobe -40C 1st Sidelobe +25C 1st Sidelobe +85C 2nd Sidelobe -40C 2nd Sidelobe +25C 2nd Sidelobe +85C -46 -50 -54 -58 -62 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 -66 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Output Power (dBm) Output Power (dBm) Figure 16: Tx Path ACPR Sidelobes 1 & 2 vs. Output Power Across Supply Voltage (Freq = 2.45 GHz, TA = Voltage Freq = 2.45 = C Filtering (bT=0.5), 1 Mbps +25oC) 802.11b GaussianGHz, T(bT+250.5), 1 Mbps 802.11b Gaussian Filtering = -22 -26 -30 -34 Figure 17: Tx Path Detector Voltage vs. Output o Across Freq (VCC = vs.3.6 V, TA = +Frequency Figure 17: Tx Path Detector Voltage + Output Power Across 25 C) Vcc = +3.6 V, T = +25 C 802.11b Gaussian Filtering=(bT=0.5), 1 Mbps 802.11b Gaussian Filtering (bT 0.5), 1 Mbps 1.2 1.1 1.0 0.9 Det. Volt. 2.40GHz Det. Volt. 2.45GHz Det. Volt. 2.50GHz ACPR Sidelobe (dBr) -38 -42 -46 -50 -54 -58 -62 -66 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 1st Sidelobe 3.30V 1st Sidelobe 3.60V 1st Sidelobe 4.20V 2nd Sidelobe 3.30V 2nd Sidelobe 3.60V 2nd Sidelobe 4.20V Detector Voltage (V) 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Output Power (dBm) Output Power (dBm) Figure 18: Tx Path Detector Voltage vs. Output Across Temp (Freq =vs. Output GHz, VCC = +3.6 V) Figure 18: Tx Path Detector Voltage 2.45 Po wer Across Temperature Frequency = 802.11b Gaussian2.45 GHz, Voltage0.5), 1 MVbps Filtering = +3.6 (bT=0.5), 1 Mbps 802.11b Gaussian Filtering (bT = 1.2 1.1 1.0 0.9 Figure 19: Tx Path Detector Voltage vs. Output Across Supply Voltage (Freq = 2.45 GHz, TA= Voltage Freq = 2.45 GHz, T = +25 C +25oC) 802.11b Gaussian Filtering bps 802.11b Gaussian Filtering (bT = 0.5), 1 M (bT=0.5), 1 Mbps 1.2 1.1 1.0 0.9 Det. Volt. -40C Det. Volt. +25C Det. Volt.+85C Det. Volt. 3.3V Det. Volt. 3.6V Det. Volt. 4.2V Detector Voltage (V) 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Detector Voltage (V) 0.8 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0 1 2 Output Power (dBm) 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Output Power (dBm) 10 Data Sheet - Rev 2.0 02/2008 AWL6254 Figure 20: Tx Path S-Parameters S21 Response Figure 20: Tx Path S-Parameters S21 Response= (VCC = +3.6 V, T= +25 C+25oC) A Vcc = +3.6 V, T 35 30 25 20 15 10 5 0 0 -2 -4 -6 -8 -10 Figure 21: Tx Figure 21: S-Parameters S11 & S22 Path Tx Path S-Parameters S22 Response (VS11=&+3.6+ResponseC TA = +25oC) CC = 3.6 V, Vcc V, T = +25 S11/S22 (dB) S21 Mag (dB) -12 -14 -16 -18 -20 -22 -24 -26 -28 -30 -32 -34 S21 (dB) -5 -10 -15 -20 -25 -30 -35 -40 -45 -50 -55 -60 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 S11 Mag (dB) S22 Mag (dB) 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Frequency (GHz) Frequency (GHz) Figure 22: Receive Path Noise Figure Across Figure 22: Receive Path Noise Supply Voltage (VLNA_ENT=+25 C Figure TA = +25oC) =+3.3 V, =+3.3 V, V LNA_EN Figure 23: Receive Path Output P1dB Across Figure 23: Receive Path =+3.3 V, Freq (VCC = +3.6 V, VLNA_ENOutput P1dB TA = +25oC) 15 2.5 Vcc=+3.6 V, VLNA_EN=+3.3 V, T=+25 C 2.45 +3.3V Noise Figure 2.4 +3.6V Noise Figure +4.2V Noise Figure 14 2.4GHz 2.45GHz 2.50GHz OP1dB Points Noise Figure (dB) 2.35 13 2.3 2.25 Gain (dB) 12 11 2.2 2.15 2.1 2.4 2.41 2.42 2.43 2.44 2.45 2.46 2.47 2.48 2.49 2.5 10 -11 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 Frequency (GHz) Output Power (dBm) Figure 24: Receive Path Output P1dB Across Supply Voltage (Freq =2.45 GHz, VLNA_EN=+3.3 V, Figure 24: Receive Path Output P1dB =+3.3 Frequency = 2.45 = +V TA GHz, 25oC) V, T=+25 C 15 LNA_EN Figure 25: Rx Path S-Parameters S21 Response Figure 25: Rx Path S-Parameters S21 Response= (VCC = +3.6 V, T= +25 C+25oC) A Vcc = +3.6 V, T 20 15 10 5 0 -5 -10 +3.3 V 14 +3.6 V +4.2 V OP1dB Points Gain (dB) S21 (dB) 13 -15 -20 -25 -30 -35 -40 12 S21 Mag (dB) 11 -45 -50 -55 -60 0 -11 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Frequency (GHz) Output Power (dBm) Data Sheet - Rev 2.0 02/2008 11 AWL6254 Figure 26: Rx Path S-Parameters S21 & S22 Figure 26: Rx Response (VS11 &=Path S-Parameters = +25oC) CC S22 Response TA +3.6 V, 4 2 0 -2 -4 -6 -8 -10 -12 -14 -16 -18 -20 -22 -24 -26 -28 -30 -32 -34 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Figure 27: Bluetooth S-Parameters S21 Figure 27: Bluetooth S-Parameters S21 +3.6 Response (VCC =Response V, TA = +25oC) 3.0 2.5 2.0 1.5 1.0 0.5 0.0 Vcc = +3.6 V, T = +25 C Vcc = +3.6 V, T = +25 C S21 Mag (dB) S11/S22 (dB) S21 (dB) -0.5 -1.0 -1.5 -2.0 -2.5 -3.0 -3.5 -4.0 -4.5 -5.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 S11 Mag (dB) S22 Mag (dB) Frequency (GHz) Frequency (GHz) 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 Figure 28:Bluetooth S-Parameters S11 & S22 Figure 28: Bluetooth S-Parameters S11 S22 CC = +Response 3.6 V, Response (VVcc =&+3.6 V, T = +25 C TA = +25oC) S11 Mag (dB) S22 Mag (dB) S11/S22 (dB) 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Frequency (GHz) 12 Data Sheet - Rev 2.0 02/2008 AWL6254 APPLICATION INFORMATION CONNECT TO ANTENNA DETECTOR OUTPUT CONNECT TO BLUETOOTH 16 15 14 13 VCC C1 0.1 F 16 V 20 % 1 2 DET_OUT GND GND ANT BLUETOOTH GND RX_RF GND VCC NC GND PA_IN 12 11 10 9 CONNECT TO RX 3 4 AWL6254 LNA_EN PA_EN 7 BT_EN 5 6 8 GND **NOTES** 3- BIT CONTROL CONNECT TO TX RF traces should be 18 mils wide with 20 mils of clearance. DC traces should be 8 mils wide with 8 mils of clearance. Figure 29: Application Circuit Data Sheet - Rev 2.0 02/2008 13 AWL6254 PACKAGE OUTLINE C 4 A D I G 16 1 H B Pin 1 Index Area Top View MILLIMETERS DIMENSION A B C D E F G H I MIN 2.90 2.90 0.50 0.00 1.55 TYP MAX 3.00 3.10 3.00 3.10 0.55 0.60 0.02 0.05 1.70 1.85 1.50 BSC. 0.18 0.25 0.30 0.50 BSC. 0.20 0.30 0.40 Side View F E Bottom View 1. All dimensions are in millimeters, angles in degrees. 2. The terminal #1 identifier and pad numbering convention shall conform to JESD 95-1 SPP-012 . 3. Lead coplanarity: 0.05 max. 4. Dimension applies to metalized pad and is measured between 0.25 and 0.30 MM from pad tip. Figure 30: S35 Package Outline - 16 Pin 3 mm x 3 mm x 0.55 mm ULPCC Figure 31: Branding Specification 14 Data Sheet - Rev 2.0 02/2008 AWL6254 Figure 32: Recommended PCB Layout (all units are in mils) Data Sheet - Rev 2.0 02/2008 15 AWL6254 ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE -40 °C to +85 °C PACKAGE DESCRIPTION RoHS-compliant 16 Pin 3 mm x 3 mm x 0.55 mm Surface Mount IC RoHS-compliant 16 Pin 3 mm x 3 mm x 0.55 mm Surface Mount IC COMPONENT PACKAGING AWL6254RS35P8 2,500 piece Tape and Reel EVA6254RS35 -40 °C to +85 °C 1 piece Evaluation Board ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. WARNING 16 Data Sheet - Rev 2.0 02/2008