PRFS-P2020-007

Preliminary R FSP2020 2.4–2.5 GHz Power Amplifier Applications • • Product Description The RFSP2020 power amplifier is a highperformance GaAs HBT IC designed for use in transmit applications in the 2.4-2.5 GHz frequency band. With a P1dB of 25 dBm, the device is ideal as a final stage for wireless LAN applications requiring high transmit linearity. Designed with advanced linearizing techniques, the device achieves a specific error vector magnitude (EVM) with lesser backoff than conventional PA designs. The PA exhibits unparalleled linearity and efficiency for both 802.11b- and 802.11g-based WLAN systems. The on-chip detector is perfect for systems where power sensing is necessary. The part operates off a single +3.3V supply. 802.11b/g WLAN 2.4 GHz ISM band wireless equipment 16 VCC1 VCC2 VCC3 15 GND 14 13 RF IN 1 12 GND GND 2 Input Match Output Match 11 RF OUT VPC1 3 Bias Bias Detector 10 GND Product Features 9 NC VPC2/3 4 • • • • • 5 VBC1 6 VBC2/3 3.00 7 DET REF 8 DET OUT 1.00 0.80 4 0.275 0.225 Functional Block Diagram • • 25 dBm P1dB@3.3V 30 dB gain 1.5 % EVM @ POUT = +18 dBm with 54 Mbps OFDM signal 110 mA @ POUT = +18 dBm with 54 Mbps OFDM signal Single +3.3V supply voltage PA power on/off logic Input and output matched to 50 ohms Pin 1 Index Area 0.45 0.35 3.00 16 1 0.50 TYP 1. All dimensions are in millimeters, angles in degrees. 2. The terminal #1 identifier and pad numbering convention shall conform to JESD 95-1 SPP-012 3. Lead coplanarity: 0.05 max. 4. Dimension applies to metalized pad and is measured between 0.25 and 0.30 MM from pad tip. 1.50 0.05 1.80 SQ Top View Side View Bottom View 3x3 mm Package Outline 05/2003 RFSP2020 2.4–2.5 GHz Power Amplifier Parameter 1 Specification Min. Typ. Max. 2500 25 30 1.5 ±0.75 -27 -50 -60 40 10 10 3.3 110 215 0.5 0.1 3.3 0.7 1 0.8 1.0 Unit MHz dBm dB % dB dBc dBc dBc/30 kHz dB dB dB V mA mA V V V V µA µs µs Condition Overall Frequency Range Output P1dB Gain Error Vector Magnitude2 Gain Flatness Harmonics 2nd Harmonic 3rd Harmonic Spurious (Stability)3 Reverse Isolation Input Return Loss Output Return Loss Power Supply Operating Voltage Current Consumption Detector Characteristics Output Voltage Output Voltage Reference Diode Shutdown Control Device On Logic High Device Off Logic Low Device Off Current Turn-On Time Turn-Off Time 2400 POUT = +18 dBm POUT = +18 dBm; 54 Mbps OFDM signal Across 100 MHz Band @ P1dB @ P1dB POUT = -20 dBm to P1dB POUT = +18 dBm; 54 Mbps OFDM signal POUT = +23 dBm; 802.11b ACPR compliant POUT = +25 dBm; RL = 5 k POUT = +19 dBm; RL = 5 k Available as part of matched pair With 50Ω source With 50Ω source Note 1: Test Conditions: VCC = 3. 3V, Freq. = 2450 MHz, T =25°C, Small Signal Conditions unless otherwise stated. Note 2: Increase in EVM over system EVM floor. Note 3: Load VSWR is set to 7:1 and the angle is varied 360 degrees. Absolute Maximum Ratings Parameter DC Power Supply DC Supply Current Maximum RF input level Operating Ambient Temperature Storage Temperature Rating 6.0 400 -1 -40 to +85 -55 to +150 Unit V mA dBm °C °C Ordering Information Part Number PRFS-P2020-EVL PRFS-P2020-005 PRFS-P2020-006 PRFS-P2020-007 PRFS-P2020-008 PRFS-P2020-009 Temp. Range (°C) -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 Package Description Evaluation Board 13" Reverse Tape/Reel 13" Tape/Reel 7" Reverse Tape/Reel 7" Tape/Reel Bulk – 4x4 mm 24-pin LPCC Quantity 1 2500 pcs. 2500 pcs. 1000 pcs. 1000 pcs. 1-999 pcs. 2 05/2003 NOTES 05/2003 3 ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059,U.S.A. Tel: +1(908)668-5000 Fax: +1(908)668-5132 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 4 05/2003