BD0810J50200AHF

Model BD0810J50200AHF Rev A Ultra Low Profile 0805 Balun 50Ω to 200Ω Balanced Description The BD0810J50200AHF is a low profile sub-miniature balanced to unbalanced transformer designed for differential inputs and output locations on next generation wireless chipsets in an easy to use surface mount package covering the GSM frequency. The BD0810J50200AHF is ideal for high volume manufacturing and is higher performance than traditional ceramic and lumped element baluns. The BD0810J50200A00 has an unbalanced port impedance of 50Ω and a 200Ω balanced port impedance. This transformation enables single ended signals to be applied to differential ports on modern semiconductors. The output ports have equal amplitude (-3dB) with 180 degree phase differential. The BD0810J50200AHF is available on tape and reel for pick and place high volume manufacturing. Detailed Electrical Specifications: Specifications subject to change without notice. ROOM (25°°C) Features: • • • • • • • • • • • 800 – 1000 MHz 0.7mm Height Profile 50 Ohm to 2 x 100 Ohm GSM Low Insertion Loss Input to Output DC Isolation Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant Halogen Free Parameter Min. Frequency Unbalanced Port Impedance Balanced Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance CMRR Power Handling 800 Typ. Unit 1000 2 MHz Ω Ω dB dB dB Degrees dB Watts +85 ºC 50 200 19 0.7 0.6 5.9 24.6 14.5 Operating Temperature Max 1.0 1.1 8.0 -55 * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing TOP VIEW (Near Side) 2.04±0.10 SIDE VIEW BOTTOM VIEW (Far Side) 0.68±0.07 1 4x 0.37 2 3 2x 0.15 1.29±0.10 6x 0.98 Orientation Marker Denotes Pin Location Orientation Marker Denotes Pin Location 6x 0.22 6 5 4 4x 0.65 Mechanical Outline -Dimensions are in Millimeters 6x 0.30 Pin Designation 1 Unbalanced Port 2 GND/DC Feed +RF GND 3 Balanced Port 4 Balanced Port 5 GND 6 NC Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model BD0810J50200AHF Rev A Typical Broadband Performance: 100 MHz. to 4.0 GHz. Insertion Loss -3 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 -15 -1.5 Frequency [MHz] 3100 3300 3500 3700 3900 3500 3700 3900 2300 2500 2500 2300 2100 1900 1700 1500 1300 1100 900 700 500 3900 3700 3500 3300 3100 2900 2700 -20 2500 -15 -2 2300 -1.5 2100 -10 1900 -1 1700 -5 1500 -0.5 300 0 100 0 1300 3300 5 900 2900 0.5 1100 3100 10 700 2700 1 500 2900 15 deg 2 1.5 300 2100 Phase Balance 20 100 1900 Frequency [MHz] Amplitude Balance [dB] 2700 Frequency [MHz] 1700 1500 100 3900 3700 3500 3300 3100 2900 2700 2500 2300 2100 1900 1700 1500 1300 900 1100 -3.6 700 -36 500 -3.3 300 -3 -33 1300 -2.7 -30 900 -2.4 -27 1100 -2.1 -24 700 -1.8 -21 500 -18 300 [dB] 0 0 100 [dB] Return Loss - Input Frequency [MHz] CM RR 0 -3 -6 -9 -12 -18 -21 -24 -27 -30 -33 3900 3700 3500 3300 3100 2900 2700 2500 2300 2100 1900 1700 1500 1300 1100 900 700 500 300 -36 100 [dB] -15 Frequency [MHz] Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model BD0810J50200AHF Rev A Typical Performance: 600 MHz. to 1200 MHz. Return Loss - Input Insertion Loss 0 -3 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 -15 -1.5 [dB] -18 -1.8 -21 -2.1 -24 -2.4 -27 -2.7 -30 -3 -33 -3.3 1150 1200 1150 1200 950 900 850 800 1200 1200 750 1150 1150 Frequency [MHz] 700 1100 -20 1100 -2 1050 -15 1050 -1.5 1000 -10 1000 -1 650 0 -5 600 0 -0.5 950 1100 5 900 1100 0.5 850 1050 10 800 1050 15 1 750 1000 1.5 deg 20 700 950 Phase Balance 2 650 1000 Amplitude Balance 600 900 Frequency [MHz] Frequency [MHz] [dB] 850 800 750 600 1200 1150 1100 1050 1000 950 900 850 800 750 700 650 600 700 -3.6 -36 650 [dB] 0 Frequency [MHz] CMRR 0 -3 -6 -9 -12 -18 -21 -24 -27 -30 -33 950 900 850 800 750 700 650 -36 600 [dB] -15 Frequency [MHz] Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model BD0810J50200AHF Rev A Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from organic PTFE based composites which possess excellent electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier. An example of the PCB footprint used in the testing of these parts is shown below. An example of a DC-biased footprint is also shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. No Bias Footprint Circuit Pattern Dimensions are in Millimeters Mounting Footprint Footprint Pad (s) DC Bias Footprint Circuit Pattern Footprint Pad (s) Solder Resist Dimensions are in Millimeters Mounting Footprint Plated thru holes to ground Solder Resist Capacitor 6x .41 4x .25 DC Bias Plated thru holes to ground 6x .41 3x Transmission lines 3x Transmission lines .04 .04 6x .33 6x .33 .66 .66 4x .25 Plated thru holes to ground Visit us at www.anaren.com Plated thru holes to ground USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model BD0810J50200AHF Rev A Packaging and Ordering Information Parts are available in reel and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information. 2.00 .81 4.00 1.75 3.50 8.00 1.60 4.00 2.41 .25 Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282