BD2130J5050AHF

Model BD2130J5050AHF Rev D Ultra Low Profile 0805 Balun 50Ω to 50Ω Balanced Description The BD2130J5050AHF is a low profile sub-miniature balanced to unbalanced transformer designed for differential inputs and output locations on next generation wireless chipsets in an easy to use surface mount package covering 802.11b+g+n. The BD2130J5050AHF is ideal for high volume manufacturing and is higher performance than traditional ceramic and lumped element baluns. The BD2130J5050AHF has an unbalanced port impedance of 50Ω and a 50Ω balanced port impedance. This transformation enables single ended signals to be applied to differential ports on modern semiconductors. The output ports have equal amplitude (-3dB) with 180 degree phase differential. The BD2130J5050AHF is available on tape and reel for pick and place high volume manufacturing. Detailed Electrical Specifications*: Specifications subject to change without notice. ROOM (25°C) Features: • • • • • • • • • • • • 2.1 – 3.0 GHz 0.7mm Height Profile 50 Ohm to 2 x 25 Ohm 802.11 b & g +n Compliant Low Insertion Loss DCS, PCS & UMTS Input to Output DC Isolation Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant Halogen Free Parameter Min. Frequency Unbalanced Port Imp. Balanced Port Imp. Return Loss Insertion Loss* Amplitude Balance Phase Balance CMRR Power Handling @85C Power Handling @105C Operating Temperature Typ. 2.4 12 50 50 17 0.75 0.45 2 35 Max Min. 2.5 2.1 0.9 0.65 5 -55 Unit 3.0 GHz Ω Ω dB dB dB Degrees dB Watts Watts ºC 1.2 1.0 5 2 1.2 +140 -55 * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Max 50 50 12 1.0 0.7 2 35 10 2 1.2 +140 Typ. Outline Drawing TOP VIEW (Near Side) 2.04±0.10 SIDE VIEW BOTTOM VIEW (Far Side) 0.68±0.07 1 4x 0.37 2 3 2x 0.15 1.29±0.10 6x 0.98 Orientation Marker Denotes Pin Location Mechanical Outline -Dimensions are in Millimeters Orientation Marker Denotes Pin Location 6x 0.22 6 5 4 4x 0.65 6x 0.30 Pin Designation 1 In 2 GND/DC Feed +RF GND 3 Out 1 4 Out 2 5 GND 6 NC Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model BD2130J5050AHF Rev D Typical Performance: 1.9 GHz. to 3.1 GHz Return Loss -3 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 -15 -1.5 -18 -1.8 -21 -2.1 -24 -2.4 -27 -2.7 -3 -30 -3.3 -33 -36 Differential insertion loss 0 [dB] [dB] 0 -3.6 1.9 2.1 2.3 2.5 2.7 2.9 3.1 1.9 2.1 2.3 Freq [GHz] Amplitude Balance 2.7 2.9 3.1 2.7 2.9 3.1 Phase balance 20 1.5 15 1 10 0.5 5 [degree] [dB] 2 2.5 Freq [GHz] 0 -0.5 0 -5 -10 -1 -15 -1.5 -2 1.9 -20 2.1 2.3 2.5 2.7 2.9 3.1 1.9 2.1 2.3 2.5 Freq [GHz] Freq [GHz] CMRR 0 -5 -10 -15 [dB] -20 -25 -30 -35 -40 -45 -50 1.9 2.1 2.3 2.5 2.7 2.9 3.1 Freq [GHz] Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model BD2130J5050AHF Rev D Typical Broadband Performance: 0.01 GHz to 8.01 GHz Return Loss 0 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 -15 -1.5 -18 -1.8 [dB] [dB] -3 -21 -2.1 -24 -2.4 -27 -2.7 -3 -30 -3.3 -33 -36 0.01 Differential insertion loss 0 1.01 2.01 3.01 4.01 5.01 6.01 7.01 -3.6 0.01 8.01 1.01 2.01 Amplitude Balance 6.01 7.01 8.01 5.01 6.01 7.01 8.01 15 1 10 0.5 5 [degree] [dB] 5.01 Phase balance 20 1.5 0 -0.5 0 -5 -10 -1 -15 -1.5 -2 0.01 4.01 Freq [GHz] Freq [GHz] 2 3.01 1.01 2.01 3.01 4.01 5.01 6.01 7.01 8.01 5.01 6.01 7.01 8.01 Freq [GHz] -20 0.01 1.01 2.01 3.01 4.01 Freq [GHz] CMRR 0 -5 -10 -15 [dB] -20 -25 -30 -35 -40 -45 -50 0.01 1.01 2.01 3.01 4.01 Freq [GHz] Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model BD2130J5050AHF Rev D Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from organic PTFE based composites which possess excellent electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier. An example of the PCB footprint used in the testing of these parts is shown below. An example of a DC-biased footprint is also shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. DC Bias Footprint No Bias Footprint Circuit Pattern Dimensions are in Millimeters Mounting Footprint Footprint Pad (s) Footprint Pad (s) Dimensions are in Millimeters Mounting Footprint Plated thru holes to ground Solder Resist Solder Resist 6x .41 Circuit Pattern 0402 Capacitor 4x .25 6x .41 Plated thru holes to ground .04 6x .33 3x Transmission lines .04 6x .33 .66 .66 Plated thru holes to ground 4x .25 Visit us at www.anaren.com 3x Transmission lines Plated thru holes to ground USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model BD2130J5050AHF Rev D Packaging and Ordering Information Parts are available in reel and are packaged per EIA 481-D. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. 2.00 .25 4.00 1.75 3.50 8.00 1.60 2.41 .81 4.00 Direction of Part Feed (Unloading) Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282