PB58

厂商：
APEX
封装：
TO3-8
描述：
IC OPAMP POWER 1MHZ TO3-8

数据手册：

下载PB58.pdf

立即购买

数据手册
价格&库存

PB58 数据手册

�� FEATURES • WIDE SUPPLY RANGE — ±15V to ±150V • HIGH OUTPUT CURRENT — 1.5A Continuous (PB58) 2.0A Continuous (PB58A) • VOLTAGE AND CURRENT GAIN • HIGH SLEW — 50V/µs Minimum (PB58) 75V/µs Minimum (PB58A) • PROGRAMMABLE OUTPUT CURRENT LIMIT • HIGH POWER BANDWIDTH — 320 kHz Minimum • LOW QUIESCENT CURRENT — 12mA Typical • EVALUATION KIT — See EK50 8-PIN TO-3 PACKAGE STYLE CE EQUIVALENT SCHEMATIC � �� APPLICATIONS • HIGH VOLTAGE INSTRUMENTATION • Electrostatic TRANSDUCERS & DEFLECTION • Programmable Power Supplies Up to 280V p-p �� DESCRIPTION The PB58 is a high voltage, high current ampliﬁer designed to provide voltage and current gain for a small signal, general purpose op amp. Including the power booster within the feedback loop of the driver ampliﬁer results in a composite ampliﬁer with the accuracy of the driver and the extended output voltage range and current capability of the booster. The PB58 can also be used without a driver in some applications, requiring only an external current limit resistor to function properly. The output stage utilizes complementary MOSFETs, providing symmetrical output impedance and eliminating second breakdown limitations imposed by Bipolar Transistors. Internal feedback and gainset resistors are provided for a pin-strapable gain of 3. Additional gain can be achieved with a single external resistor. Compensation is not required for most driver/gain conﬁgurations, but can be accomplished with a single external capacitor. Enormous ﬂexibility is provided through the choice of driver ampliﬁer, current limit, supply voltage, voltage gain, and compensation. This hybrid circuit utilizes a beryllia (BeO) substrate, thick ﬁlm resistors, ceramic capacitors and semiconductor chips to maximize reliability, minimize size and give top performance. Ultrasonically bonded aluminum wires provide reliable interconnections at all operating temperatures. The 8-pin TO-3 package is electrically isolated and hermetically sealed using one-shot resistance welding. The use of compressible isolation washers voids the warranty. �� EXTERNAL CONNECTIONS �� TYPICAL APPLICATION �� Figure 1. Inverting composite ampliﬁer. �� APEX MICROTECHNOLOGY CORPORATION • TELEPHONE (520) 690-8600 • FAX (520) 888-3329 • ORDERS (520) 690-8601 • EMAIL prodlit@apexmicrotech.com 1 PB58 • PB58A ABSOLUTE MAXIMUM RATINGS SUPPLY VOLTAGE, +VS to –VS OUTPUT CURRENT, within SOA POWER DISSIPATION, internal at TC = 25°C1 INPUT VOLTAGE, referred to COM TEMPERATURE, pin solder—10 sec max TEMPERATURE, junction1 TEMPERATURE, storage OPERATING TEMPERATURE RANGE, case ABSOLUTE MAXIMUM RATINGS SPECIFICATIONS 300V 2.0A 83W ±15V 300°C 175°C –65 to +150°C –55 to +125°C SPECIFICATIONS PARAMETER INPUT OFFSET VOLTAGE, initial OFFSET VOLTAGE, vs. temperature INPUT IMPEDANCE, DC INPUT CAPACITANCE CLOSED LOOP GAIN RANGE GAIN ACCURACY, internal Rg, Rf GAIN ACCURACY, external Rf PHASE SHIFT OUTPUT VOLTAGE SWING VOLTAGE SWING VOLTAGE SWING CURRENT, continuous SLEW RATE CAPACITIVE LOAD SETTLING TIME to .1% POWER BANDWIDTH SMALL SIGNAL BANDWIDTH SMALL SIGNAL BANDWIDTH POWER SUPPLY VOLTAGE, ±VS4 CURRENT, quiescent TEST CONDITIONS2 MIN PB58 TYP ±.75 –4.5 50 3 10 ±10 ±15 10 60 VS –8 VS –7 VS –5 100 2200 2 320 100 1 ±60 11 12 14 1.2 1.6 30 25 ±150 18 1.3 1.8 85 * MAX ±1.75 –7 * 25 ±15 ±25 * MIN PB58A TYP * * * * * * * * * VS–11 * * * * * * * * * * * * * * * * * * * * * MAX ±1.0 * * * * UNITS V mV/°C kΩ pF V/V % % ° ° V V V A V/µs pF µs kHz kHz MHz V mA mA mA °C/W °C/W °C/W °C Full temperature range3 25 3 AV = 3 AV = 10 f = 10kHz, AVCL = 10, CC = 22pF f = 200kHz, AVCL = 10, CC = 22pF Io = 1.5A (PB58), 2A (PB58A) Io = 1A Io = .1A Full temperature range Full temperature range RL = 100Ω, 2V step VC = 100 Vpp CC = 22pF, AV = 25, Vcc = ±100 CC = 22pF, AV = 3, Vcc = ±30 Full temperature range VS = ±15 VS = ±60 VS = ±150 Full temp. range, f > 60Hz Full temp. range, f < 60Hz Full temperature range Meets full range speciﬁcations VS–11 VS–10 VS–8 1.5 50 160 VS–15 * * 2.0 75 240 ±156 * THERMAL RESISTANCE, AC junction to case5 RESISTANCE, DC junction to case RESISTANCE, junction to air TEMPERATURE RANGE, case –25 NOTES: * The speciﬁcation of PB58A is identical to the speciﬁcation for PB58 in applicable column to the left. 1. Long term operation at the maximum junction temperature will result in reduced product life. Derate internal power dissipation to achieve high MTTF (Mean Time to Failure). 2. The power supply voltage speciﬁed under typical (TYP) applies, TC = 25°C unless otherwise noted. 3. Guaranteed by design but not tested. 4. +VS and –VS denote the positive and negative supply rail respectively. 5. Rating applies if the output current alternates between both output transistors at a rate faster than 60Hz. 6. +VS/–VS must be at least 15V above/below COM. CAUTION The PB58 is constructed from MOSFET transistors. ESD handling procedures must be observed. The internal substrate contains beryllia (BeO). Do not break the seal. If accidentally broken, do not crush, machine, or subject to temperatures in excess of 850°C to avoid generating toxic fumes. APEX MICROTECHNOLOGY CORPORATION • 5980 NORTH SHANNON ROAD • TUCSON, ARIZONA 85741 • USA • APPLICATIONS HOTLINE: 1 (800) 546-2739 2 TYPICAL PERFORMANCE GRAPHS PB58 • PB58A � �� APEX MICROTECHNOLOGY CORPORATION • TELEPHONE (520) 690-8600 • FAX (520) 888-3329 • ORDERS (520) 690-8601 • EMAIL prodlit@apexmicrotech.com �� 3 PB58 • PB58A GENERAL Please read Application Note 1 "General Operating Considerations" which covers stability, supplies, heat sinking, mounting, current limit, SOA interpretation, and speciﬁcation interpretation. Visit www.apexmicrotech.com for design tools that help automate tasks such as calculations for stability, internal power dissipation, current limit; heat sink selection; Apex’s complete Application Notes library; Technical Seminar Workbook; and Evaluation Kits. OPERATING CONSIDERATIONS STABILITY Stability can be maximized by observing the following guidelines: 1. Operate the booster in the lowest practical gain. 2. Operate the driver ampliﬁer in the highest practical effective gain. 3. Keep gain-bandwidth product of the driver lower than the closed loop bandwidth of the booster. 4. Minimize phase shift within the loop. A good compromise for (1) and (2) is to set booster gain from 3 to 10 with total (composite) gain at least a factor of 3 times booster gain. Guideline (3) implies compensating the driver as required in low composite gain conﬁgurations. Phase shift within the loop (4) is minimized through use of booster and loop compensation capacitors Cc and Cf when required. Typical values are 5pF to 33pF. Stability is the most difﬁcult to achieve in a conﬁguration where driver effective gain is unity (ie; total gain = booster gain). For this situation, Table 1 gives compensation values for optimum square wave response with the op amp drivers listed. DRIVER OP07 741 LF155 LF156 TL070 CCH 22p CF 22p 18p 4.7p 4.7p 15p CC 22p 10p 10p 10p 10p FPBW 4kHz 20kHz 60kHz 80kHz 80kHz SR 1.5 7 >60 >60 >60 CURRENT LIMIT For proper operation, the current limit resistor (RCL) must be connected as shown in the external connection diagram. The minimum value is 0.33Ω with a maximum practical value of 47Ω. For optimum reliability the resistor value should be set as high as possible. The value is calculated as follows: +IL= .65/RCL + .010, -IL = .65/RCL. �� For: RF = 33K, RI = 3.3K, RG = 22K Table 1: Typical values for case where op amp effective gain = 1. �� SAFE OPERATING AREA NOTE: The output stage is protected against transient ﬂyback. However, for protection against sustained, high energy ﬂyback, external fast-recovery diodes should be used. �� COMPOSITE AMPLIFIER CONSIDERATIONS Cascading two ampliﬁers within a feedback loop has many advantages, but also requires careful consideration of several ampliﬁer and system parameters. The most important of these are gain, stability, slew rate, and output swing of the driver. Operating the booster ampliﬁer in higher gains results in a higher slew rate and lower output swing requirement for the driver, but makes stability more difﬁcult to achieve. �� Figure 2. Non-inverting composite ampliﬁer. SLEW RATE The slew rate of the composite ampliﬁer is equal to the slew rate of the driver times the booster gain, with a maximum value equal to the booster slew rate. GAIN SET RG = [ (Av-1) • 3.1K] – 6.2K R + 6.2K Av = G +1 3.1K The booster’s closed-loop gain is given by the equation above. The composite ampliﬁer’s closed loop gain is determined by the feedback network, that is: –Rf/Ri (inverting) or 1+Rf/Ri (non-inverting). The driver ampliﬁer’s “effective gain” is equal to the composite gain divided by the booster gain. Example: Inverting conﬁguration (ﬁgure 1) with R i = 2K, R f = 60K, R g = 0 : Av (booster) = (6.2K/3.1K) + 1 = 3 Av (composite) = 60K/2K = – 30 Av (driver) = – 30/3 = –10 OUTPUT SWING The maximum output voltage swing required from the driver op amp is equal to the maximum output swing from the booster divided by the booster gain. The Vos of the booster must also be supplied by the driver, and should be subtracted from the available swing range of the driver. Note also that effects of Vos drift and booster gain accuracy should be considered when calculating maximum available driver swing. This data sheet has been carefully checked and is believed to be reliable, SHANNON ROAD • TUCSON, ARIZONA 85741 omissions. All speciﬁcations are subject APEX MICROTECHNOLOGY CORPORATION • 5980 NORTHhowever, no responsibility is assumed for possible inaccuracies•orUSA • APPLICATIONS HOTLINE:to1change without notice. (800) 546-2739 4 PB58U REV I OCTOBER 2004 © 2004 Apex Microtechnology Corp.

下载 PDF

PB58 价格&库存

-> 查询更多价格&库存

很抱歉，暂时无法提供与“PB58”相匹配的价格&库存，您可以联系我们找货

免费人工找货

搜索历史

PB58

推荐型号

相关技术文章