NLP150L-96S8

NLP150L Series • • • • • • • • • • • Single and triple outputs 1 LOW TO MEDIUM POWER AC/DC POWER SUPPLIES 110-150W AC/DC Universal Input Switch Mode Power Supplies 90VAC to 264VAC universal input range Provides low voltage outputs of 3.3V EN61000-3-2 compliant Overvoltage and short circuit protection Power fail detection Current sharing (on VA and VB) 3.8 x 6.8 x 1.26 inches UL, CSA and VDE safety approvals and CE-marked to LVD Compliance to EN55022-B conducted noise standard Compliance to EN55022-A radiated noise standard Meets all applicable and relevant immunity standards EN61000-4-2, -3, -4, -5 and -6 The NLP150L series of 150 Watt AC/DC open frame power supplies are available with single, triple or quad outputs. The single and triple output versions described in this datasheet are housed in a 3.8 x 6.8 x 1.26 inch package. All NLP150L series power supplies are harmonic current corrected to meet the EN61000-3-2 standard, and support current sharing. The power supplies are designed for use in 1U shelves or boxes, and are primarily intended for networking applications that have a heavy logic content, such as access concentrators, midrange routers, LAN switches and shared media hubs. All specifications are typical at nominal input, full load at 25°C unless otherwise stated Patent No. 5600546 and 5652700 2 YEAR WARRANTY SPECIFICATIONS (11) OUTPUT SPECIFICATIONS Total regulation (Line and load) Turn-on delay Transient response Main output Auxiliary outputs @ 120VAC Input Main output 75% to 100% step at 0.1A/µs ±2.0% ±5.0% 2.0s, max. 5.0% or 250mV max. dev., 1ms max. recovery to 1% ±0.02%/°C Main outputs Cyclic operation Singles and multiple 125%, ±10% Continuous See table EMC CHARACTERISTICS (continued) Surge Fast transients Radiated immunity Conducted immunity EN61000-4-5 EN61000-4-4 EN61000-4-3 EN61000-4-6 Level Level Level Level 3 3 3 3 GENERAL SPECIFICATIONS Hold-up time Efficiency (See Note 13) Isolation voltage Approvals and standards pending Weight 120VAC @ 60Hz 120VAC @ 150W Input/output Input/chassis 20ms @ 150W 73% typical 3000VAC 1500VAC Temperature coefficient Overvoltage protection Short circuit protection Minimum output current INPUT SPECIFICATIONS Input voltage range (See Note 12) Input frequency range Input surge current Safety ground leakage current Input current Input fuse 264VAC (cold start) 264VAC, 60Hz 120VAC @ 150W 230VAC @ 150W UL/IEC127 (11) EN60950, VDE0805, IEC950 UL1950, CSA C22.2 No. 950 540g (19oz) MIL-HDBK-217F Bellcore (8) Universal input 90 to 264VAC 47Hz to 63Hz 40A max. 0.99mA 1.95A rms 1.10A rms F3.15A H, 250VAC MTBF (@ 25°C) 350,000 hours min. 800,000 hours min. ENVIRONMENTAL SPECIFICATIONS Thermal performance EMC CHARACTERISTICS Conducted emissions Radiated emissions Harmonic current emission correction ESD air ESD contact Operating ambient, 0°C to +50°C (See derating curve) Non-operating -40°C to +85°C 50°C to 70°C ambient, Derate to convection cooled 50% load 0°C to 50°C ambient, 110W convection cooled 0°C to 50°C ambient, 150W 300LFM forced air Peak (0°C to +50°C) (See Note 3) Non-condensing Operating Non-operating 5Hz to 500Hz per MIL-STD-810E 5% to 95% RH 10,000 feet max. 30,000 feet max. 2.4G rms peak 516.4 Part IV EN55022, FCC part 15 EN55022, FCC part 15 EN61000-3-2 EN61000-4-2 EN61000-4-2 Level B Level A Compliant Level 3 Level 3 Relative humidity Altitude Vibration (See Note 6) Shock File Name: NLP150LST.PDF Rev: 24 June 2002 NLP150L Series OUTPUT VOLTAGE 3.3V (VA) 5.1V (VA) +12V (VA) 24V (VA) 48V (VA) +5.1V (VA) +3.3V (VB) +12V (VC) +12V (VA) +5.1V (VB) +24V (VC) Notes 1 Free air convection. Multiple output units: maximum continuous output power not to exceed 110W and the output current not to exceed: IA+IB+2(IC)≤23A. 300LFM forced air cooling from the longer side. Multiple output units: maximum continuous output power not to exceed 150W and the output current not to exceed: IA+IB+2(IC)≤32A. Peak power at 115% lasting less than 30 seconds with duty cycle less than 5%. During peak loading, output voltage may exceed total regulation limits. Figure is peak-to-peak for room temperature rating. Output noise measurements are made across a 20MHz bandwidth using a 6 inch twisted pair, terminated with a 10µF electrolytic capacitor and a 0.1µF ceramic capacitor. Minimum load required for correct start-up and operation on single outputs and on main output of multiple versions. Failure to observe minimum load on main output will not allow the supply to start-up correctly. Some electronic test loads have a large delay time before they start drawing current even though the voltage from the supply is present. During this time delay, there is no load on the output and as a result, the supply may not be able to start-up properly and maintain its correct output voltage. In these instances, a dummy resistive load across the output may be necessary to load the output of the supply until the test load can function correctly and draw the intended minimum load. Minimum load required on auxiliary outputs to maintain regulation. Three orthogonal axes, random vibration 10 minutes for each axes, 2.4G rms 5Hz to 500Hz. For optimum reliability no part of the heatsink should exceed 110°C and no semi-conductor case temperature should exceed 115°C. CAUTION: Allow a minimum of 1 second after disconnecting line power when making thermal measurements. This product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. The EMI specifications reference measurements made with the power supply mounted on a grounded metal sheet extending 1 inch beyond each edge, using an unshielded cable. No external filtering required during conducted emissions testing but some applications may require additional filtering to achieve system compliance All models require a minimum mounting stand-off of 6.35mm (0.25 inches) in the end use product. Operational range 90VAC to 264VAC. For 3.3V ouput (single), typical efficiency is 69%. Single and triple outputs 2 LOW TO MEDIUM POWER AC/DC POWER SUPPLIES 110-150W AC/DC Universal Input Switch Mode Power Supplies For the most current data and application support visit www.artesyn.com/powergroup/products.htm OUTPUT CURRENT RIPPLE MIN 1A 1A 0.3A 0.15A 0.1A 1.5A 0.5A 0A 0.6A 0.5A 0A (5) (4) TOTAL REGULATION MODEL NUMBERS NLP150L-96S3 NLP150L-96S5 NLP150L-96S6 NLP150L-96S8 NLP150L-96S9 NLP150L-96T536 MAX (1) 300 LFM 30A 30A 12.5A 6.5A 3.2A 30A 15A 3A 12.5A 8A 3.0A (2) 22A 22A 9.2A 4.6A 2.3A 20A 10A 2A 9.2A 6A 2.0A 50mV 50mV 120mV 240mV 480mV 50mV 50mV 120mV 120mV 50mV 240mV ±2.0% ±2.0% ±2.0% ±2.0% ±2.0% ±2.0% ±2.0% ±5.0% ±2.0% ±2.0% ±5.0% NLP150L-96T658 DERATING CURVE Output Power (Watts) 2 150W 110W 3 4 300 LFM FORCED AIR COOLING 5 NATURAL CONVECTION COOLING 75W 55W 0°C 10°C 20°C 30°C 40°C 50°C 60°C 70°C 6 7 8 9 10 International Safety Standard Approvals VDE0805/EN60950/IEC950 UL1950 11 12 13 Please consult our website for the following items: Application Note www.artesyn.com File Name: NLP150LST.PDF Rev: 24 June 2002 NLP150L Series Mechanical Notes A All dimensions are in inches (mm). Single and triple outputs 3 LOW TO MEDIUM POWER AC/DC POWER SUPPLIES 110-150W AC/DC Universal Input Switch Mode Power Supplies For the most current data and application support visit www.artesyn.com/powergroup/products.htm 1 6.800 (172.72) 6.450 (163.83) 3.925 (99.70) J2 1 2 1 0.175 (4.45) 4 3 J3 3.800 (96.52) 3.450 (87.63) 2 Recommended direction for forced air relative to power supply orientation shown below. 1 2 3 4 Best. Good. Not recommended. Not recommended. J5 T1 (REF.) 1 3 J1 F1 J6 5 1 2 Ø0.156 (Ø3.96) 0.175 (4.45) JCS JRM3 JRM5 2 1 2 1 2 1 (5 PLS) ALL DIMENSIONS IN INCHES (MM) MAXIMUM COMPONENT HEIGHT 1.26 (32.00) CONNECTOR J1 J2 J3 J5 J6 JRM3, JRM5 & JCS TYPE CONNECTOR AND MATING CONNECTOR TYPES MATING CONNECTOR TYPE Molex 09-50-3031 or equivalent with Molex 08-50-0105 or equivalent crimp terminals Molex AA-5261, AA22-01 or equivalent Molex 09-50-3021 or equivalent with Molex 2478 phosphor bronze or equivalent crimp terminals N/A Molex 22-01-2021 and contact 08-50-0113 terminals or equivalent Leoco 2420S02000 and contact 2453TPB00V1 Molex 26-60-4030 or equivalent Male 0.250 quick disconnect Molex 26-60-4040 or equivalent Beau Interconnect 70505-C-50 or equivalent Molex 22-23-3021 or equivalent Leoco 2421P02H000 or equivalent J1 PIN CONNECTIONS Pin 1 Neutral Pin 2 Void Pin 3 Line J3 PIN CONNECTIONS Pin 1 VD Positive Pin 2 VD RTN Note: VD is a floating output. It can be configured as positibe or negative J5 PIN CONNECTIONS Pin 1 VA Positive Pin 2 VA Positive Pin 3 Main RTN Pin 4 Main RTN Pin 5 VB Positive JRM5 PIN CONNECTIONS Pin 1 VA Sense + Pin 2 VA Sense JRM3 PIN CONNECTIONS Pin 1 Pin 2 VB Sense + VB Sense - J6 PIN CONNECTIONS Pin 1 Signal Pin 2 RTN JCS PIN CONNECTIONS Pin 1 Load A Current Sharing Pin 2 Load B Current Sharing Data Sheet © Artesyn Technologies® 2002 The information and specifications contained in this data sheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein. Please consult our website for the following items: Application Note www.artesyn.com File Name: NLP150LST.PDF Rev: 24 June 2002