12104D107MAT2A

X5R Dielectric General Specifications GENERAL DESCRIPTION • General Purpose Dielectric for Ceramic Capacitors • EIA Class II Dielectric • Temperature variation of capacitance is within ±15% from -55°C to +85°C • Well suited for decoupling and filtering applications • Available in High Capacitance values (up to 100μF) PART NUMBER (see page 2 for complete part number explanation) 1210 Size (L" x W") 4 Voltage 4 = 4V 6 = 6.3V Z = 10V Y = 16V 3 = 25V D = 35V 5 = 50V D Dielectric D = X5R 107 Capacitance Code (In pF) 2 Sig. Digits + Number of Zeros M Capacitance Tolerance K = ±10% M = ±20% A Failure Rate A = N/A T Terminations T = Plated Ni and Sn 2 Packaging 2 = 7" Reel 4 = 13" Reel 7 = Bulk Cass. 9 = Bulk A Special Code A = Std. NOTE: Contact factory for availability of Tolerance Options for Specific Part Numbers. Contact factory for non-specified capacitance values. TYPICAL ELECTRICAL CHARACTERISTICS Insulation Resistance (Ohm-Farads) Temperature Coefficient 20 15 Insulation Resistance vs Temperature 10,000 Capacitance 10 5 0 -5 -10 -15 -20 -60 -40 -20 0 +20 +40 +60 +80 1,000 100 % Temperature °C 0 0 20 40 60 80 100 120 Temperature °C 23 X5R Dielectric Specifications and Test Methods Parameter/Test Operating Temperature Range Capacitance Dissipation Factor X5R Specification Limits -55ºC to +85ºC Within specified tolerance ≤ 2.5% for ≥ 50V DC rating ≤ 3.0% for 25V DC rating ≤ 12.5% Max. for 16V DC rating and lower Contact Factory for DF by PN 100,000MΩ or 500MΩ - μF, whichever is less No breakdown or visual defects No defects ≤ ±12% Meets Initial Values (As Above) ≥ Initial Value x 0.3 ≥ 95% of each terminal should be covered with fresh solder No defects, 10 μF, 0.5Vrms @ 120Hz Charge device with rated voltage for 120 ± 5 secs @ room temp/humidity Charge device with 300% of rated voltage for 1-5 seconds, w/charge and discharge current limited to 50 mA (max) Deflection: 2mm Test Time: 30 seconds 1mm/sec Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance Resistance to Flexure Stresses Solderability Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength Dip device in eutectic solder at 230 ± 5ºC for 5.0 ± 0.5 seconds Resistance to Solder Heat Thermal Shock Load Life Repeat for 5 cycles and measure after 24 ± 2 hours at room temperature Charge device with 1.5X rated voltage in test chamber set at 85ºC ± 2ºC for 1000 hours (+48, -0). Note: Contact factory for *optional specification part numbers that are tested at < 1.5X rated voltage. Remove from test chamber and stabilize at room temperature for 24 ± 2 hours before measuring. Store in a test chamber set at 85ºC ± 2ºC/ 85% ± 5% relative humidity for 1000 hours (+48, -0) with rated voltage applied. Remove from chamber and stabilize at room temperature and humidity for 24 ± 2 hours before measuring. Load Humidity 24 X5R Dielectric Capacitance Range PREFERRED SIZES ARE SHADED SIZE Soldering Packaging (L) Length (W) Width (t) Terminal MM (in.) MM (in.) MM (in.) WVDC 100 150 220 330 470 680 1000 1500 2200 3300 4700 6800 Cap (μF) 0.010 0.015 0.022 0.033 0.047 0.068 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 10 22 47 100 WVDC 0201 Reflow Only All Paper 0.60 ± 0.03 (0.024 ± 0.001) 0.30 ± 0.03 (0.011 ± 0.001) 0.15 ± 0.05 (0.006 ± 0.002) 4 6.3 10 16 25 A A A A A A A A A A 0402 Reflow Only All Paper 1.00 ± 0.10 (0.040 ± 0.004) 0.50 ± 0.10 (0.020 ± 0.004) 0.25 ± 0.15 (0.010 ± 0.006) 4 6.3 10 16 25 50 0603 Reflow Only All Paper 0805 Reflow/Wave Paper/Embossed 1206 Reflow/Wave Paper/Embossed 1210 Reflow/Wave Paper/Embossed 1812 Reflow Only All Embossed 1.60 ± 0.15 (0.063 ± 0.006) 0.81 ± 0.15 (0.032 ± 0.006) 0.35 ± 0.15 (0.014 ± 0.006) 4 6.3 10 16 25 35 50 6.3 2.01 ± 0.20 3.20 ± 0.20 (0.079 ± 0.008) (0.126 ± 0.008) 1.25 ± 0.20 1.60 ± 0.20 (0.049 ± 0.008) (0.063 ± 0.008) 0.50 ± 0.25 0.50 ± 0.25 (0.020 ± 0.010) (0.020 ± 0.010) 10 16 25 35 50 6.3 10 16 25 35 50 3.20 ± 0.20 4.50 ± 0.30 (0.126 ± 0.008) (0.177 ± 0.012) 2.50 ± 0.20 3.20 ± 0.20 (0.098 ± 0.008) (0.126 ± 0.008) 0.50 ± 0.25 0.61 ± 0.36 (0.020 ± 0.010) (0.024 ± 0.014) 4 6.3 10 16 25 35 50 6.3 10 25 50 Cap (pF) C C C C C C C C C C C C C G G G G G G G G G G G G G G G G G G G G G G N N N N N N N N N N N N* * N N N N N N N N N* Q Q Q Q Q Q Q Q Q P* Q Q Q Q N N Q Q Q Q Q Q Z Q Q X Z Z Z X X L W T A A A A A A A A t C C C C C C C C C C C C C N N N N N Q X X G G G G G G J K G J G J G J J X Z 4 6.3 10 16 25 4 6.3 10 16 25 50 4 6.3 10 16 25 35 50 6.3 10 16 25 35 50 6.3 10 16 25 35 50 ZZZZ Z Z Z* 4 6.3 10 16 25 35 50 6.3 10 25 50 SIZE Letter Max. Thickness A 0.33 (0.013) 0201 C 0.56 (0.022) E 0.71 (0.028) PAPER 0402 G 0.90 (0.035) J 0.94 (0.037) 0603 K 1.02 (0.040) M 1.27 (0.050) N 1.40 (0.055) 0805 P Q 1.52 1.78 (0.060) (0.070) EMBOSSED 1206 X 2.29 (0.090) Y 2.54 (0.100) 1210 Z 2.79 (0.110) 1812 = Under Development *Optional Specifications – Contact factory NOTE: Contact factory for non-specified capacitance values 25