AP1184K5-33L-U

NOT RECOMMENDED FOR NEW DESIGN AP1184 4A ULTRA LOW DROPOUT POSITIVE ADJUSTABLE OR FIXED-MODE REGULATOR General Description Features         0.85V maximum dropout voltage at 4A load current Built-in Thermal shutdown Output current limiting Adjustable or fixed output voltage1.5V, 1.8V, 2.5V, 3.3V, 5.0V Fast transient response Good noise rejection Packages: TO220-5L and TO263-5L Lead Free Finish/ RoHS Complian (Note 1) AP1184 is a 4A regulator with extremely low dropout voltage. This product is specifically designed to provide well regulated supply for applications requiring 2.8V or lower voltages from 3.3V ATX power supplies where high efficiency of the switch can be achieved without the cost and complexity associated with switching regulator. One such application is the new graphic chipsets that requires anywhere from 2.4V to 2.7V supply. Ordering Information AP1184 XX - XX L - X Package Vout Lead Free Packing K5 : TO263-5L T5 : TO220-5L Blank : Adj 15 = 1.5V 18 = 1.8V 25 = 2.5V 33 = 3.3V 50 = 5.0V L : Lead Free U : Tube 13 : Tape & Reel Device Lead-free Lead-free AP1184K5XXL-U AP1184K5XXL-13 AP1184T5XXL-U Package Code Packaging (Note 2) K5 K5 T5 TO263-5L TO263-5L TO220-5L Tube Part Number Quantity Suffix 50 -U NA NA 50 -U 13” Tape and Reel Part Number Quantity Suffix NA NA 800/Tape & Reel -13 NA NA Lead-free Notes: 1. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied, see EU Directive 2002/95/EC Annex Notes. 2. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at http://www.diodes.com/datasheets/ap02001.pdf. AP1184 Rev. 6 - 3 1 of 12 www.diodes.com OCTOBER 2014 © Diodes Incorporated NOT RECOMMENDED FOR NEW DESIGN AP1184 4A ULTRA LOW DROPOUT POSITIVE ADJUSTABLE OR FIXED-MODE REGULATOR Pin Assignments FRONT VIEW FRONT VIEW 5 4 3 2 1 Vin Vctrl Vout Adj(GND) Vsense Vin Vctrl Vout Adj(GND) Vsense 5 4 3 2 1 Tab is Vout Tab is Vout TO263-5L TO220-5L Pin Descriptions Pin Numbers with standard type are for TO220-5L, TO263-5L packages. Name I/O Description Adj A resistor divider from this pin to the Vout pin and ground sets the output voltage. (GND (GND) only for fixed mode) This pin is the positive side of the reference that allows remote load sensing to achieve Vsense I excellent load regulation. A minimum of 10uF capacitor must be connected from this pin to ground to insure stability. The input of the regulator. Typically a large storage capacitor is connected from this pin to ground to insure that the input voltage does not sag below the minimum dropout Vin I voltage during the load transient response. This pin must always be higher than Vout in order for the device to regulate. This pin is the supply pin for the internal control circuit as well as the base drive for the pass transistor. This pin must always be higher than the Vout pin in order to regulate the Vctrl I device. A minimum of 100uF capacitor must be connected from this pin to ground to insure stability. The output of the regulator. A minimum of 100uF capacitor must be connected from this Vout O pin to ground to insure stability. Block Diagram Vin Vout Vsense Vctrl + + － 1.25V + CURRENT LIMIT + AP1184 Rev. 6 - 3 － THERMAL SHUTDOWN 2 of 12 www.diodes.com Adj OCTOBER 2014 © Diodes Incorporated NOT RECOMMENDED FOR NEW DESIGN AP1184 4A ULTRA LOW DROPOUT POSITIVE ADJUSTABLE OR FIXED-MODE REGULATOR Typical Application Circuit (1) Adjustable Regulator 5V 3.3V 470µF 470µF Vin Vctrl Vout 2.5V/ 4A R1 121 Ω Adj 470µF R2 121 Ω Vsense Tab is Vout R Note : V V  (1  2 ) OUT REF R 1 (2) 3.3V to 2.5V Fixed Mode Regulator 5V 3.3V 470µF 470µF Vin Vctrl 2.5V/ 4A Vout GND 470µF Vsense Tab is Vout Absolute Maximum Ratings Symbol VIN Vctrl PD TST TOP Parameter Input Voltage Control Input voltage Power dissipation Storage temperature Range Operation Junction Temperature Range AP1184 Rev. 6 - 3 3 of 12 www.diodes.com Rating Unit 16 18 Internally limited -65 to +150 0 to +125 V V o C C o OCTOBER 2014 © Diodes Incorporated NOT RECOMMENDED FOR NEW DESIGN AP1184 4A ULTRA LOW DROPOUT POSITIVE ADJUSTABLE OR FIXED-MODE REGULATOR Electrical Characteristics (Under Operating Conditions) Unless otherwise specified, these specifications apply over, Cin = 1uF, Cout = 10uF, and Tj = 0 to 150oC. Typical value refer to TA = 25oC. Vout = Vsense Sym. Parameter Test Condition Min Typ. Max Unit 1.225 1.250 1.275 V 0.2 % 1.470 1.500 1.530 V 1.764 1.800 1.836 V 2.450 2.500 2.550 V 3.235 3.300 3.365 V 4.900 5.000 5.100 V 1 % 12 15 mV 15 18 mV 20 25 mV 26 33 mV 40 50 mV 1.10 1.15 1.18 1.25 0.26 0.50 0.70 0.38 0.60 0.85 o VREF Reference Voltage Line Regulation Vout Output Voltage Load Regulation Dropout Voltage (Vctrl –Vout) Dropout Voltage (Vin – Vout) Io =10mA, TA = 25 C, (Vin-Vout) = 0.7V, AP1184-Adj Vctrl = VIN+1V o I = 10mA, VOUT+0.7V