PI5A4157TAEX

PI5A4157 Low Voltage SPDT 0.8Ω Analog Switch Features Description  The PI5A4157 is a high-bandwidth, fast single-pole double-throw (SPDT) CMOS switch. It can be used as an analog switch or as a low-delay bus switch. The device features ultra low RON of 0.8Ω typical at 3.0V VCC and will operate over the wide VCC range of 1.65V to 5.5V. The PI5A4157 features very low quiescent current even when the control voltage is lower than the VCC supply. This feature services the mobile handset applications very well by allowing direct interface with baseband processor general purpose I/Os. Break-before-make switching prevents both switches being enabled simultaneously. This eliminates signal disruption during switching. The control input, S, is independent of supply voltage.         CMOS Technology for Bus and Analog Applications Low On-Resistance: 0.8Ω at 3.0V Wide VCC Range: 1.65V to 5.5V Rail-to-Rail Signal Range Control Input Overvoltage Tolerance: 5.5V(Min) Fast Transition Speed: 12ns at 5.0V High Bandwidth: 150 MHz Extended Industrial Temperature Range: -40°C to 85°C Packaging (Pb-free & Green): -6-pin SOT23 -6-pin SC70 -6-Pin UDFN 1mm×1mm Applications      Cell Phones PDAs Portable Instrumentation Battery powered Communications Computer Peripherals Pin Assignment B1 1 6 S GND 2 5 VCC B0 3 4 A SOT23-6 and SC70-6(Top View) B0 2 5 B1 A 4 S 3 UDFN-6 1×1 (Top View) Pin Description Pin No SOT23-6 UDFN-6 SC70-6 1×1 1 5 2 1 3 2 4 3 5 6 6 4 6 VCC GND 1 Logic Function Table Pin Name B1 GND B0 A VCC S Description Logic Inputs(S) 0 B0 connect to A 1 B1 connect to A Data Port Ground Data Port (Normally connected) Common Output/Data Port Positive Power Supply Logic control All trademarks are property of their respective owners. 2017-01-0009 www.diodes.com 1 Function 1/18/2017 PT0386-4 PI5A4157 Maximum Ratings Storage Temperature…………………………………...-65℃ to +150℃ Ambient Temperature with Power Applied......................-40℃ to +85℃ Supply Voltage VCC ……………………………………..-0.5V to +7.0V DC Switch Voltage VS ……………………………-0.5V to VCC+0.5V DC Input Voltage VIN … ……………………………..-0.5V to +7.0V DC Output Current VOUT……………………………………….128mA DC VCC or Ground Current ICC /IGND … ………………………±100mA Junction Temperature under Bias (TJ) ...........................................150°C Junction Lead Temperature (TL) (Soldering, 10 seconds) ................................................................ 260°C ESD（HBM）.................................................................................5KV Power Dissipation (PD) @ +85°C ...................................SOT23 250mW SC70 200mW UDFN1x1 150mW Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Recommended Operating Conditions Symbol VCC VIN VS VOUT TA Parameter Operating Voltage Control Input Voltage Switch Input Voltage Output Voltage Operating Temperature Conditions Control Input VCC = 2.7V to 3.6V Input Rise and Fall Time tr, tf Control Input VCC = 4.5V to 5.5V Note: Control input must be held HIGH or LOW; it must not float. All trademarks are property of their respective owners. 2017-01-0009 Min. 1.65 0 0 0 -40 0 0 www.diodes.com 2 Typ. 25 - Max. 5.5 VCC VCC VCC 85 10 5 Unit V V V V °C ns/V ns/V 1/18/2017 PT0386-4 PI5A4157 DC Electrical Characteristics (TA = –40°C to 85°C, unless otherwise noted.) Parameter Description Test Conditions Supply Voltage Min Typ Max Units VIAR Analog Input Signal Range - VCC 0 - VCC V 4.5V 3.0V 2.3V 1.65V - 0.7 0.6 0.8 0.8 0.9 1.0 1.2 1.3 2.0 0.01 0.02 0.03 0.03 1.1 1.0 1.2 1.3 1.9 1.5 1.8 1.9 2.8 0.03 0.04 0.06 0.06 4.5V - 0.2 RON ∆RON RONF (1) ON Resistance ON Resistance Match Between Channels(1,2,3) ON Resistance Flatness(1,2,4) IO = 100mA, VIN = 0V IO = 100mA, VIN = 2.4V IO = 100mA, VIN = 4.5V IO = 100mA, VIN = 0V IO = 100mA, VIN = 3.0V IO = 100mA, VIN = 0V IO = 100mA, VIN = 2.3V IO = 100mA, VIN = 0V IO = 100mA, VIN = 1.65V IA =100mA, VBn =3.15V IA = 100mA, VBn = 2.1V IA =100mA, VBn = 1.6V IA = 100mA, VBn = 1.15V IA = 100mA, VBn = 0V,2.4V,4.5V IA = 100mA, VBn = 0V,1.5V,3.3V IA = 100mA, VBn = 0V,1.1V,2.5V IA = 100mA, VBn = 0V, 0.7V,1.8V 4.5V 3.0V 2.3V 1.65V   0.4 3.3V - 0.2 2.5V - 0.4 0.6 1.8V - 1.0 1.4 VCC = 1.65V VCC = 2.3V VCC = 3V VCC = 4.2V VCC = 5.5V VCC = 1.65V VCC = 2.3V VCC = 3V VCC = 4.2V VCC = 5.5V 0.9 1.0 1.1 1.2 1.3 - - 0.6 0.6 0.6 0.8 0.8  VIH Input High Voltage Logic High Level VIL Input Low Voltage Logic Low Level IOFF (NO) or IOFF (NC) INC(ON), INO(ON), ICOM (ON) Source Off Leakage Current VCC=5.5V, VA =1V, 4.5V VBn =1V, 4.5V VCC = 3V -20 - +20 Channel On Leakage Current - VCC = 1.65 to 5.5V -40 - +40 All channels ON or OFF, VIN = VCC or GND, IOUT=0 VCC = 3.6V VCC = 5.5V - 0.002 0.002 0.1 0.1 µA Input at 2.7V VCC = 4.3V - 0.2 10.0 µA ICC ICCT Quiescent Supply Current Increase in ICC per Input V V nA Notes: 1. Measured by voltage drop between A and B pins at the indicated current through the device. ON resistance is determined by the lower of the voltages on two ports (A or B). 2. Parameter is characterized but not tested in production. 3. ∆RON = RON max –RON min. measured at identical VCC, temperature and voltage levels. 4. Flatness is defined as difference between maximum and minimum value of ON resistance over the specified range of conditions. All trademarks are property of their respective owners. 2017-01-0009 www.diodes.com 3 1/18/2017 PT0386-4 PI5A4157 Capacitance (1) Symbol CIN CIO-B CIOA-ON Parameter Control Input For B Port, Switch OFF For A Port, Switch ON Test Conditions VCC = 5.0V, f =1 MHz, TA=25°C Min - Typ 3.5 15.0 34.0 Max - Units pF Notes: 1. Capacitance is characterized but not tested in production Switch and AC Characteristics (1) Parameter Description Test Conditions Supply Voltage Break Before Make Time See Figure 2 tON Turn on Time See Figure 1 tOFF Turn off Time Q Charge Injection CL = 1nF, VGEN = 0V, RGEN=0. See Figure 3 Off Isolation tBBM Min Typ Max VCC = 2.7V to 3.6V - 10 20 VCC = 4.5V to 5.5V - 6 12 VCC = 2.7V to 3.6V - 12 25 VCC = 4.5V to 5.5V - 9 18 17 35 10 20 - VCC = 2.7V to 3.6V See Figure 1 VCC = 4.5V to 5.5V - Units ns VCC = 5.0V - 35 - VCC = 3.3V - 25 - RL=50, VGEN=0V, RGEN =0, f =1MHz. See Figure 4 (2) VCC =1.65V to 5.5V - -70 - Crosstalk Isolation f=1MHz, See Figure 5 VCC =1.65V to 5.5V - -70 - f3dB –3dB Bandwidth See Figure 8 VCC =1.65V to 5.5V - 150 - MHz THD Total Harmonic Distortion RL=600Ω, VIN=0.5Vpp, f=20Hz to 20kHz See Figure 9 VCC =2.7V to 4.2V - 0.015 - % OIRR XTALK pC dB Notes: 1. Guaranteed by design. 2. Off Isolation = 20 Log10 [ VBn/VA ] and is measured in dB. All trademarks are property of their respective owners. 2017-01-0009 www.diodes.com 4 1/18/2017 PT0386-4 PI5A4157 Test Circuits and Timing Diagrams Figure 1. Turn ON/OFF Timing 50Ω 35pF Figure 2. Break Before Make Interval Timing All trademarks are property of their respective owners. 2017-01-0009 www.diodes.com 5 1/18/2017 PT0386-4 PI5A4157 1nF Figure 3. Charge Injection Test 0V or VIH Figure 5. Crosstalk Figure 4. Off Isolation 0V or VIH 0V or VIH Figure 6. Channel Off Capacitance Figure 7. Channel On Capacitance All trademarks are property of their respective owners. 2017-01-0009 www.diodes.com 6 1/18/2017 PT0386-4 PI5A4157 0V or VIH Figure 8. Bandwidth 600Ω Figure 9. Harmonic Distortion All trademarks are property of their respective owners. 2017-01-0009 www.diodes.com 7 1/18/2017 PT0386-4 PI5A4157 Mechanical Information TA (6-pin SOT23) All trademarks are property of their respective owners. 2017-01-0009 www.diodes.com 8 1/18/2017 PT0386-4 PI5A4157 C (6-pin SC70) All trademarks are property of their respective owners. 2017-01-0009 www.diodes.com 9 1/18/2017 PT0386-4 PI5A4157 ZU (6-pin UDFN 1x1) Marking Description Shortened Date Code 6 5 4 gX 1 2 3 Shortened Part No All trademarks are property of their respective owners. 2017-01-0009 www.diodes.com 10 1/18/2017 PT0386-4 PI5A4157 Note: For latest package info, please check: http://www.pericom.com/products/packaging/mechanicals.php Ordering Information Part Number Package Code PI5A4157CEX C Package Top Marking 6-Pin, SOT363 (SC70), Tape & Reel mA mA PI5A4157TAEX TA 6-Pin, Small Outline Transistor Plastic Package (SOT23), Tape & reel PI5A4157ZUEX ZU 6-Pin, 1x1 (UDFN), Tape & reel g Notes: • Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ • E = Pb-free and Green • X suffix = Tape/Reel All trademarks are property of their respective owners. 2017-01-0009 www.diodes.com 11 1/18/2017 PT0386-4 PI5A4157 IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2016, Diodes Incorporated www.diodes.com All trademarks are property of their respective owners. 2017-01-0009 www.diodes.com 12 1/18/2017 PT0386-4