PI90LV017AUEX

PI90LV031A PI90LV027A PI90LV017A 3V LVDS High-Speed Differential Line Drivers Features Description • Signaling Rates >400Mbps (200 MHz) The PI90LV031A, PI90LV027A, and PI90LV017A are differential line drivers that use low-voltage differential signaling (LVDS) to support data rates in excess of 400 Mbps. These products are designed for applications requiring high-speed, low-power consumption and low noise generation. • Single 3.3V Power Supply Design • ±350mV Differential Swing • Maximum Differential Skew of 0.4ns A low voltage TTL/CMOS input level is translated by the device into a low-voltage (350mV) differential output signal. Exclusive to the PI90LV031A quad driver is a power-down mode that 3-states the outputs and places the device in a low-power idle state (13mW typical). • Maximum Propagation Delay of 2.0ns • Maximum Power Dissipation: 25mW @ 200 MHz/driver • Low Voltage TTL (LVTTL) Inputs • Industrial Temperature Operating Range: -40°C to 85°C Applications Applications include point-to-point and multidrop baseband data transmission over controlled impedance media of approximately 100 ohms. The transmission media can be printed circuit board traces, backplanes, or cables. • Meets or Exceeds IEEE 1596.3 SCI LVDS Standard • Meets or Exceeds ANSI/TIA/EIA-644 LVDS Standard The PI90LV031A, PI90LV027A, PI90LV017A and companion line receivers (PI90LV032A, PI90LV028A, and PI90LV018A) provide new alternatives to RS-232, PECL, and ECL devices for high-speed, point-to-point interface applications. • Packaging (Pb-free & Green available): PI90LV017A & PI90LV027A - 8-pin SOIC (W) - 8-pin MSOP (U) PI90LV031A - 16-pin SOIC (W) - 16-pin TSSOP (L) PI90LV027A PI90LV031A DIN1 DOUT1+ DOUT1EN DOUT2DOUT2+ DIN2 GND 1 2 3 4 16-Pin 5 L,W 6 7 8 16 15 14 13 12 11 10 9 VCC DIN4 DOUT4+ DOUT4EN* DOUT3DOUT3+ DIN3 DIN1 D1 DIN2 D2 DIN3 D3 DIN4 D4 VCC DIN1 DIN2 GND DOUT1+ DOUT1- DOUT1DOUT1+ DOUT2+ DOUT2- DIN1 D1 DIN2 D2 DIN1 D1 DOUT1+ DOUT1DOUT2+ DOUT2- DOUT2+ DOUT2- PI90LV017A DOUT3+ DOUT3DOUT4+ VCC DIN1 NC GND DOUT4- EN EN* 13-0018 1 8 2 8-Pin 7 3 U,W 6 4 5 1 1 8 2 8-Pin 7 3 U,W 6 4 5 DOUT1DOUT1+ NC NC PS8422D DOUT1+ DOUT1- 12/12/12 PI90LV031A / PI90LV027A / PI90LV017A 3V LVDS High-Speed Differential Line Drivers Function Tables Pin Descriptions PI90LV031A Enables Input Outputs Name Description EN EN DIN DOUT+ DOUT– DIN TTL/CMOS driver input pins H X H H L DO+ Non-inverting driver output pins H X L L H DO– Inverting driver output pins X L H H L GND Ground pin X L L L H VCC Positive power supply pin, +3.3V ±10% L H X Z Z Recommended Operating Conditions PI90LV027A Input Outputs DIN DOUT+ DOUT- H H L L L H PI90LV017A Input Min. Typ. Max. Units Supply Voltage (VCC) +3.0 +3.3 +3.6 V Operating Free Air Temperature –40 +25 +85 °C Outputs DIN DOUT+ DOUT- H H L L L H Absolute Maximum Ratings (see Note 1, Page 4) Supply Voltage (VCC) .........................................................–0.3V to +4.0V Input Voltage (DIN)..............................................................–0.3V to (VCC +0.3V) Enable Input Voltage (EN, EN*)........................................–0.3V to (VCC +0.3V) Output Voltage (DOUT+, DOUT-).............................................–0.3V to +3.9V Short Circuit Duration (DOUT+, DOUT-).......................................................................Continuous S Package.............................................................................. 750mW Derate S Package ................................................................8.5mW/°C above +25°C Note: Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Storage Temperature Range................................................-65°C to +150°C Lead Temperature Range Soldering (4s)............................. +260°C Maximum Junction Temperature........................................ +150°C ESD Rating............................................................................. ≥6kV 13-0018 2 PS8422D 12/12/12 PI90LV031A / PI90LV027A / PI90LV017A 3V LVDS High-Speed Differential Line Drivers Electrical Characteristics Over supply voltage and operating temperature ranges, unless otherwise specified. (Notes 2,3,4) Symbol Parameter Conditions Pin Min. Typ. Max. Units 250 350 450 mV 4 35 ImVI 1.25 1.375 V 5 25 ImVI 1.38 1.6 VOD1 Differential Output Voltage DVOD1 Change in Magnitude of VOD1 for Complementary Output States VOS Offset Voltage DVOS Change in Magnitude of VOS for Complementary Output States VOH Output Voltage High VOL Output Voltage Low VIH Input Voltage High VIL Input Voltage Low IIH Input Current VIN = VCC or 2.5V -10 ±1 +10 IIL Input Current VIN = GND or 0.4V -10 ±1 +10 VCL Input Clamp Voltage ICL = -18mA -1.5 -0.8 IOS Output Short Circuit Current ENABLED,(10) DIN = VCC, DOUT+ = 0V or DIN = GND, DOUT- = 0V IOSD Differential Output Short Circuit Current ENABLED, VOD = 0V(10) IOFF Power-off Leakage VOUT = 0V or 3.6V, VCC = 0V or Open IOZ Output Three-State Current EN = 0.8V and EN* = 2.0V VOUT = 0V or VCC ICC No Load Supply Current Drivers Enable DIN = VCC or GND ICCL Loaded Supply Current Drivers Enabled RL = 100W All Channels, DIN = VCC or GND (all inputs) ICCZ No Load Supply Current Drivers Disabled DIN = VCC or GND, EN = GND, EN* = VCC 13-0018 DOUTDOUT+ RL = 100W (Fig.1) 1.125 0.90 DIN EN EN* 1.03 2.0 VCC GND 3 DOUTDOUT+ V 0.8 mA V -6.0 -9.0 -6.0 -9.0 -20 ±1 +20 -10 ±1 +10 5.0 8.0 23 30 2.6 6.0 VCC PS8422D mA mA mA 12/12/12 PI90LV031A / PI90LV027A / PI90LV017A 3V LVDS High-Speed Differential Line Drivers Switching Characteristics VCC = +3.3V ±10%, TA = -40°C to +85°C (Notes 3,9,11) Symbol Parameter Conditions Min. Typ. Max. Rl = 100W, Cl = 10pF (Figures 2 & 3) 0.8 1.18 2.0 0.8 1.25 2.0 0 0.07 0.4 0.1 0.5 tphld Differential Propagation Delay High to Low tplhd Differential Propagation Delay Low to High tskd1 Differential Pulse Skew Itphld - tplhdI tskd2 Channel-to-Channel Skew(6) 0 tskd3 Differential Part-to-Part Skew (7) 0 1.0 tskd4 Differential Part-to-Part Skew (8) 0 1.2 ttlh Rise Time 0.38 1.5 tthl Fall Time 0.40 1.5 tphz Disable Time High to Z tplz Disable Time Low to Z tpzh Enable Time Z to High 7 tpzl Enable Time Z to Low 7 tmax Maximum Operating Frequency(13) (5) Rl = 100W, Cl = 10pF (Figures 4 & 5) Units ns 5 5 200 250 MHz Notes: 1. “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The table of “Electrical Characteristics” specifies conditions of device operation. 2. Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground except: VOD1 and ∆VOD1. 3. All typicals are given for: VCC = +3.3V, TA = +25°C. 4. The PI90LV031A/PI90LV027A/PI90LV017A are current mode devices and only functions within datasheet specifications when a resistive load is applied to the driver outputs typical range is (90Ω to 110Ω). 5. tskd1, Itphld - tplhdI is the magnitude difference in differential propagation delay time between the positive going edge and the negative going edge of the same channel. 6. tskd2 is the Differential Channel-to-Channel Skew of any event on the same device. 7. tskd3, Differential Part-to-Part Skew, is defined as the difference between the minimum and maximum specified differential propagation delays. This specification applies to devices at the same Vcc and with 5°C of each other within the operating temperature range. 8. tskd4, Part-to-Part Skew, is the differential Channel-to-Channel skew of any event between devices. This specification applies to devices over recommended operating temperature and voltage ranges, and across process distribution. tskd4 is defined as IMax - MinI differential propagation delay. 9. Generator waveform for all tests unless otherwise specified: f = 1 MHz, Zo = 50Ω, tr ≤ 1ns, and tf ≤ 1ns. 10. Output short circuit current (IOS) is specified as magnitude only, minus sign indicates direction only. 11. CL includes probe and jig capacitance. 12. All input voltages are for one channel unless otherwise specified. Other inputs are set to GND. 13. fmax generator input conditions: tR = tF < 1ns, (0% to 100%), 50% duty cycle, 0V to 3V. Output Criteria: duty cycle = 45%/55%, VOD > 250mV, all channels switching. 13-0018 4 PS8422D 12/12/12 PI90LV031A / PI90LV027A / PI90LV017A 3V LVDS High-Speed Differential Line Drivers Parameter Measurement Information DOUT+ RL/2 VCC DIN GND VOS D S1 VOD RL/2 DOUT- Driver ENABLED Figure 1. Driver VOD and VOS Test Circuit CL DOUT+ Generator DIN RL D 50-Ohm DOUT- Driver ENABLED CL Figure 2. Driver Propagation Delay and Transition Time Test Circuit 13-0018 5 PS8422D 12/12/12 PI90LV031A / PI90LV027A / PI90LV017A 3V LVDS High-Speed Differential Line Drivers Figure 3. Driver Propagation Delay and Transition Time Waveforms Figure 4. Driver Three-State Delay Test Circuit 13-0018 6 PS8422D 12/12/12 PI90LV031A / PI90LV027A / PI90LV017A 3V LVDS High-Speed Differential Line Drivers Figure 5. Driver 3-State Delay Waveform Figure 6. Point-to-Point Application 13-0018 7 PS8422D 12/12/12 DATE: 06/15/12 PI90LV031A / PI90LV027A / PI90LV017A 3V LVDS High-Speed Differential Line Drivers Packaging Mechanical: 16-Pin SOIC (W) DATE: 06/15/12 DESCRIPTION: 16-Pin, 150mil Wide SOIC PACKAGE CODE: W DOCUMENT CONTROL #: PD-1004 REVISION: F 2012-0398 13-0018 8 PS8422D 12/12/12 PI90LV031A / PI90LV027A / PI90LV017A 3V LVDS High-Speed Differential Line Drivers Packaging Mechanical: 8-Pin SOIC (W) DOCUMENT CONTROL NO. 8 PD - 1001 REVISION: F .149 .157 DATE: 03/09/05 3.78 3.99 .0099 .0196 0.25 x 45˚ 0.50 1 .189 .196 4.80 5.00 .0075 .0098 0-8˚ 0.19 0.25 0.40 .016 1.27 .050 1 .016 .026 0.406 0.660 .2284 .2440 5.80 6.20 1.35 1.75 .053 .068 SEATING PLANE REF .050 BSC 1.27 .0040 .0098 0.10 0.25 .013 0.330 .020 0.508 Pericom Semiconductor Corporation 3545 N. 1st Street, San Jose, CA 95134 1-800-435-2335 • www.pericom.com X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS Notes: 1) Controlling dimensions in millimeters. 2) Ref: JEDEC MS-012D/AA 13-0018 DESCRIPTION: 8-Pin, 150-Mil Wide, SOIC PACKAGE CODE: W 9 PS8422D 12/12/12 PI90LV031A / PI90LV027A / PI90LV017A 3V LVDS High-Speed Differential Line Drivers Packaging Mechanical: 16-Pin TSSOP (L) DATE: 05/03/12 Notes: 1. Refer JEDEC MO-153F/AB 2. Controlling dimensions in millimeters 3. Package outline exclusive of mold flash and metal burr DESCRIPTION: 16-Pin, 173mil Wide TSSOP PACKAGE CODE: L DOCUMENT CONTROL #: PD-1310 REVISION: F 12-0372 13-0018 10 PS8422D 12/12/12 PI90LV031A / PI90LV027A / PI90LV017A 3V LVDS High-Speed Differential Line Drivers Packaging Mechanical: 8-pin MSOP (U) PD - 1261 REVISION: E DATE: 03/09/05 .003 .012 0.07 0.30 Gauge Plane .010 0.25 DOCUMENT CONTROL NO. .003 .012 0.07 0.30 15˚ Max. .016 .028 0.40 0.70 15˚ Max. .037 0.95 REF 0˚- 6˚ Detail A .112 2.85 .120 3.05 Detail A 1 15˚ MAX .114 2.90 .122 3.10 15˚ MAX .114 2.90 .122 3.10 Pericom Semiconductor Corporation 3545 N. 1st Street, San Jose, CA 95134 1-800-435-2335 • www.pericom.com Notes: 1) Controlling Dimensions inMillimeters 2) Ref. JEDEC MO-187E/AA Ordering Information Ordering Code DESCRIPTION: 8-Pin Mini Small Outline Package, MSOP PACKAGE CODE: U Package Code Package Description PI90LV017AWE W Pb-free & Green, 8-pin SOIC PI90LV017AUE U Pb-free & Green, 8-pin MSOP PI90LV027AWE W Pb-free & Green, 8-pin SOIC PI90LV027AUE U Pb-free & Green, 8-pin MSOP PI90LV031AWE W Pb-free & Green, 16-pin SOIC PI90LV031ALE L Pb-free & Green, 16-pin TSSOP Notes: 1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ Pericom Semiconductor Corporation • 1-800-435-2336  •  www.pericom.com 13-0018 11 PS8422D 12/12/12